Missile Command Cocktail TM-152 1st Printing
Missile Command (rev 3, A035467-02/04 PCBs) (Atari, 1980) · Technical Manual · 44 pages · 39 sections · original scan
WLADOD GCNEMUUWO>)
GAME SERIAL NUMBER LOCATION Your game’s serial number is stamped on a plate on the outside of the game. The same number is also stamped on the chassis of the TV monitor, Regulator/Audio I! PCB, and Game PCB. Please mention this number whenever calling your distributor for service.
REGULATORI/AUDIO Il PCB
GAME SERIAL # IDENTIFICATION TAG
GAME PCB
@ COCKTAIL
Nll_JS ILE COMMUN 2
Operation, Maintenance and Service Manual
Complete with Illustrated Parts Lists
Published by: ATARI INC 1265 Borregas Avenue P. O. Box 427 Sunnyvale, California 94086
Copyright © 1980 by Atari, Inc. All rights reserved. No part of this publication may be reproduced by any mechanical, photographic, or electronic process, or in the form of a phonographic recording, nor
may it be stored in a retrieval system, transmitted, or otherwise copied for 4y
public or private use, without permission from the publisher. y @ Lithographed in the U.S.A. 7 A.
ATARI
Table of Contents
Location Setup A. N@WPAMts 0.00 teen ete tenes 1 B. Opening the Game Cabinet 3 C. Game Inspection . ea 3 D. Game Installation. 3
- Voltage Selection . 4
- Interlock and Power On/Off Switche 4 E. Adjusting the Table Legs. 5 F. Self-Test Procedure .. . 6 G. GamePlay ...... 9
- Attract Mode... 9
- Ready-to-Play Mode 9
- PlayMode .......... 9
- High Score Initial Mode ... 9
Maintenance and Repair A, Cleaning... 0... cece eee nee eens 12 B. Fuse Replacement........... see +t . 12 C. Opening the Control Panel .. 12
- LED Switch Replacement 12
- Mini-Trak Ball™ Maintenance and Repair . 13 D. TV Monitor Removal .14 E. Printed-Circuit Board Replacement 15
- Game PCB Removal ......... 15
- Regulatori/Audio Il PCB Removal . . 15 F. GameOperation...........0 0. cece cece cence eee n ne eene 16
Illustrated Parts Lists
e List of Illustrations
Figure 1 Overview of Game ..... 6.6... cece ence nce eee enn ene 2 Figure 2 Installation Requirements . 3 Figure 3 Power Supply ...........-5 - 4 Figure 4 Interlock and Power On/Off Switches .........-6-0+. eee eee eee 5
Figure 5 Adjusting the Table Legs wee 6 Figure 6 Location of Self-Test Switch, Volume Control and Option Switches 6 Figure 7 _— Self-Test Procedure wee Figure 8 Option Switch Settings ..... 2.6... eee cece eee eee
Figure 9 Opening the Control Panel and Replacing Switches ............. 12 Figure 10 Mini-Trak Ball™ Maintenance and Repair : 22 13 Figure 11. TV Monitor Removal..................000 . 14 Figure 12 Game and Regulator/Audio Il PCB Replacement . . . 16 @ Figure 13. Power Distribution ......... 0.6.6. cece cee cence eee 16 Figure 14 Signal Distribution ..... 20.0... 6... eee eee 17
Illustrated Parts Lists: Figure 15 Cabinet-Mounted Assemblies Figure 16 Control Panel Assembly .. Figure 17 Mini-Trak Ball™ Assembly . Figure 18 Missile Command™ Game PCB Assembly
Figure 19 Regulator/Audio IIPCB Assembly.............0..-..0 0s ee eee Figure 20 Power Supply Assembly for Color Raster-Scan Games . . Figure 21 Coin Acceptor Mount Assembly ............. 000. c eae cee ee eee
lf reading through this manual does not lead to solving a certain maintenance problem, call Tele-Help™ at the Atari Customer Service office in your geographical area, as shown in one of the two maps below. Order all parts from the California office.
WEST and CENTRAL U.S.A.
Parts for all Atari Customers. Sales and Service
Atari Coin-Op Customer Service 1344 Bordeaux Drive, Sunnyvale, CA 94086 Telex 17-1103
(Monday - Friday, 7:30 - 4:00 pm Pacific Time)
From California, Alaska or Hawaii es (408) 745-2900
a» From anywhere else in this area tollfree (800) 538-1611
EAST U.S.A.
Sales and Service Only
Atari Inc. New Jersey Customer Service Office Cottontail Lane, Somerset, NJ 08873 Telex 37-9347
(Monday - Friday, 7:30 - 4:00 pm Eastern time)
z From New Jersey (201) 469-5993
From anywhere else in this area toll-free (800) 526-3849
A. New Parts
The Cocktail Missile Command™ game has four new parts. If you have worked on Atari games in the past, then you should be aware of these important differences. The new parts are: —-14-Inch Color TV Monitor. Made to Atari specifications by either Matsushita or Sanyo, it has high reliability, a compact size, and should maintain its color convergence for a long period of time. © Mini-Trak Ball™ Assembly. The widely used Trak Ball Assembly has been redesigned and scaled down for use in Atari's compact cocktail-table and Cabaret games.
TABLE TOP,
START SWITCHES
, COIN ACCEPTOR
SPEAKER
COIN COUNTER
Figure 1 Overview of Game SUPPORT ARM
COLOR TV =
MONITOR
TRAK BALL™
REGULATOR! AUDIO Il PCB
POWER SUPPLY
oR, © Cocktail Table Cabinet. This new cabinet design allows for adjustable height and easy access for servicing. The tempered-glass top eliminates the possibility of spilled liquids entering into the cabinet. ¢ Coin Acceptor. This is one of the first uses of this fixed-mounting coin acceptor.
These new parts, as well as all other major parts in the game, are illustrated in Figure 1. Throughout this manual, wherever one of these new parts is mentioned, you will see this symbol in the page
margin: oC
B. Opening the Game Cabinet
Refer to Figure 1 and do the following:
Unlock and open the access panel.
- Reach inside and unfasten the hook-type latch on each end of the cabinet.
- Lift the table top until the support arm locks into place.
The inside of the cabinet, excluding the two control panels, is fully accessible for servicing.
To close the cabinet, do the following:
- Stand on the access-panel side of the cabinet and grasp the table top with your left hand.
- With the right hand, press the button at the middle of the support arm and pull the support arm toward you.
- Gently lower the table top to the closed position.
- Reach inside the access panel and lock the two latches.
- Close and lock the access panel.
C. Game Inspection
This new game is ready to play upon removal from the shipping carton. However, your careful inspection is needed to supply the final touch of quality control. Please follow these steps to help us insure that your new game was delivered to you in good condition.
- Examine the exterior of the game cabinet for dents, chips, or broken parts.
- Unlock and open the access panel of the cabinet and inspect the interior of the game as follows: @ Check that all plug-in connectors (on the game harness) are firmly seated. Replug any connectors found unplugged. DON’T FORCE CONNECTORS TOGETHER. The connectors are keyed so they only go on in the proper orientation. A reversed edge connector will damage a PCB. @ Check that all plug-in integrated circuits on the game PCB are firmly seated in their sockets.
@ Note the location of the game’s serial number—it is printed on the special label on the outside of the game cabinet. Verify that the serial numbers also stamped on the Game PCB, Regulator/Audio || PCB and TV Monitor are all identical. A drawing of the serial number locations is on the inside front cover of this manual. Please mention this number whenever you call your distributor for service. @ Check all major subassemblies such as the power supply, control panel and TV monitor for secure mounting.
D. Game Installation
°
Figure 2 Installation Requirements
Power 100 watts Temperature 0 to 38° C (32 to 100°F) Humidity Not over 95% relative Space Required 60 x 81 cm (2334 x 31% in.) Game Height 61 to 71 cm (24 to 28% in.)
VOLTAGE SELECTION PLUGS
Figure 3 Power Supply
- Voltage Selection Before plugging in your game, make sure that the voltage selection plug on the power supply (see Figure 3) is correct for your location's line voltage. Check the wire color on the plug and see if it is correct per the list below.
Voltage Selection Line Voltage Range Plug Color 90-110 VAC (100) Violet 105-135 VAC (120) Yellow 200-240 VAC (225) Blue 220-260 VAC (240) Brown
- Interlock and Power On/Off Switches
To minimize the hazard of electrical shock while working on the inside of the game cabinet, an interlock switch has been installed (see Figure 4). This switch removes all AC line power from the game cir- Cuitry when the access panel is opened.
Check for proper operation of the interlock switch by doing the following: @ Unlock and open the access panel. @ Plug the AC line power cord into an AC outlet. @ Close the access panel. @ Set the power on/off switch to the on position. Within approximately 30 seconds the TV monitor should display a picture. @ Slowly open the rear access panel. The TV monitor picture should disappear when the panel is opened approximately 2.5 cm (1 inch). Close and lock the access panel.
POWER ON/OFF SWITCH
Figure 4 Interlock and Power On/Off Switches
E. Adjusting the NOTE Table Legs To ensure Cabinet strength, you must use
all three bolts when attaching table legs. If you use only two bolts, you may break This cocktail-table game is designed for three ad- the cabinet wall when sliding the cabinet justable heights, from 61 to 71 cm. The table may be across the floor. set at 61, 66, or 71 cm. To adjust the table height, refer to Figure 5.
Before removing the table legs, be sure to support the game on its bottom surface with books or a tool chest, etc. An assistant can also hold one end of the game. Then change the position of the legs. Atari does not recommend tilting the game up and standing it on its end!
USE ALL THREE BOLTS: WHEN ATTACHING TABLE LEGS!
Figure 5 Adjusting the Table Legs
F. Self-Test Procedure Part of the self-test procedure includes a
display of the operator-selectable game options. Therefore, we suggest you run the self-test pro- This game wiil test itself and provide data to cedure anytime you need to change the game’s demonstrate that the game’s circuitry and con- options. trols are operating properly. The data is provided on the TV monitor and the game speaker; no addi- To run the self-test, follow the instructions outtional equipment is necessary. lined in Figure 7.
W VOLUME CONTROL 7 Ser test SWITCH VOLUME DECREASE: TURN CLOCKWISE
OPTION SWITCHES Figure 6 Location of Self-Test Switch,
Volume Control and Option Switches
Instruction Figure 7 Self-Test Procedure Result if Test Passes Result if Test Fails
- Set self-test switch to on position (see Figure 5). Note: entering self-test will set the HIGH SCORE TODAY display to 7500.
- Roll the player 1 Trak Ball control in ail directions.
Press any player 1 fire switch and screen will flip 180°. Roll player 2 Trak Ball in all directions.
- Press the following switches: © Coin switch trip wires @ Slam switch @ All six fire switches @ Player start buttons
- Set self-test switch to off Position. After about 5 seconds of frozen attract mode, a low raspy tone is followed by a low beep, then high beep. TV monitor screen displays picture as shown below: ROM OK MAP OK RAM OK + ..plus the options display—see Figure 8 for explanation. Both LED start buttons will also be lighted.
The + moves around on the screen in directions corresponding to Trak Ball control—up to an invisible border along the screen’s edges.
A sound is heard as each switch is pressed. The background color also changes. A continuous raspy tone means V BLANK is malfunctioning. Self-test will not continue. A RAM failure is indicated by a blank or “garbage”-filled screen and a repeated series of 8 beeps, separated by a low raspy tone. See note 1 below. Self-test will not restart. ROM failure is i see note 2 below. BAD MAP means bit-mapping hardware has failed. BAD CHIP means custom audio I/O chip at location P8/9 has failed. dicated by BAD ROM;
The + doesn’t move in same direction as ball, or not at all. One of the Steering PCBs on Trak Ball control may be bad, harness wires or connector may be loose, Trak Ball reading circuitry on Game PCB may be bad, or Trak Ball bearings may need oiling.
No sound or color changes are produced when pressing one of these switches: indicates a bad switch, loose harness wires, or loose connector.
In test no. 1, a low beep means a good chip; a
Figure 8 Option Switch Settings
verify proper results on the TV e@
To change toggle positions on the switch assemblies, you need When changing the options, not remove the game PCB. The switches, usually colored blue, are monitor display by performing the self-test. Note that changing an easily accessible when the game PCB is mounted in place. option on any toggle will cause an immediate change on the TV monitor screen during the self-test.
Toggle Settings of 8-Toggle Switch on Game PCB (at R10) 7 6
| 8 | 4 | 3 | 2 | 1 | Option |
| On | On | 1 coin* for 1 play |
Off On Free play
| On | Off | 2coins* for1 play | $ | |
| 3 | Off | Off | 1 coin* for 2 plays | |
| =. | -- | -- | a | Switch positions are irrelevant for Cocktail Missile |
3 Command
| = | On | On | English janguage |
| On | Off | French language | |
| Off | On | German language | |
| Off | Off | ‘Spanish language |
Toggle Settings of 8-Toggle Switch on Game PCB (at R8)
| 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | Option |
| Off | Off | Game starts with 7 cities | ||||||
| On | On | Game starts with 6 cities | $ | |||||
| Off | On | Game starts with 5 cities | ||||||
| On | Off | Game starts with 4 cities |
On No bonus credit
| 3 | Off | 1 bonus credit for 4 successive coins | $ |
| 8 | -_ | Switch position is irrelevant for Cocktail Missile Com- |
mand
| 2 | Of | Off | On | Bonus city every 8,000 points |
| On | On | On | Bonus city every 10,000 points | $ |
| On | On | Off | Bonus city every 12,000 points | |
| On | Off | On | Bonus city every 14,000 points | |
| On | Off | Off | Bonus city every 15,000 points | |
| Off | On | On | Bonus city every 18,000 points | |
| Off | On | Off | Bonus city every 20,000 points | |
| Off | Off | Off | No bonus city |
The format of the self-test display is as follows: An example of an actual option switch display is as follows:
| Bonus city every | points (line disappears if no bonus city is | BONUS CITY EVERY 10,000 POINTS |
chosen) + + 2 COINS 1 PLAY Coinage setting 6 CITIES
| 4, 5, 6, or 7 cities (always in English) | 1 | 1 | x |
A B cD
A, B, C: Ignore these three displays for Cocktail Missile Command. * In the U.S, a “coin” is defined as 25°. Dis an “X" if switch 3 (of R8) is off. $ Manufacturer’s suggested settings
@ G. Game Play
Missile Command" is a 1- or 2-player game witha color monitor. The game depicts an Armageddonstyle war in which players defend their bases and cities with antiballistic missiles (ABMs). The enemy—the game computer—launches incoming waves of attack missiles. These weapons may be either individual or branching-attack missiles. In addition, the enemy occasionally launches missiles from a fast-moving “killer” satellite or from bombers. The enemy also launches “smart” missiles that almost always can avoid explosions.
Players receive varying numbers of points for intercepting attack missiles, for having unused missiles still in their bases’ arsenals, and for having their cities undamaged after a missile wave.
The game has five possible modes of operation: attract, ready-to-play, play, high-score initial, and self-test. The latter is a special mode for checking the game switches and computer functions. You may enter this mode at any time. When entered, all game credits are cancelled, and the “HIGH SCORE TODAY” is reset to 7500. A list of eight “highest” scores and initials are also reset onto the screen (to provide player challenge).
- Attract Mode The attract mode begins when power is applied to the game, after a play or high-score initial mode, or after self-test. This mode is continuous and is only interrupted when a game is paid for and accepted, or when entering self-test.
In this mode, the Missile Command name is displayed, then the computer plays one wave—handling both offense and defense. Following this, the computer displays the high score table, then the Missile Command graphics reappear.
- Ready-to-Play Mode This mode begins when sufficient coins have been accepted for a one- or two-player game. It ends when the 1 PLAYER START or 2 PLAYER START pushbutton is pressed.
When this mode begins, the message PRESS START scrolls along the bottom of the screen. DE- FEND CITIES and red arrows pointing down to each city also appear on the screen. The displayed pictures are otherwise the same as those shown in the attract mode.
- Play Mode The play mode begins when either start pushbutton is pressed. The mode ends when the player's last city is destroyed.
The three bases—Alpha, Delta and Omega—each have 10 ABMs ready to be fired (shown as 4 ’s). Players must be careful to fire the missiles more or less evenly from among those bases, because no more missiles are granted until the screen resets in preparation for a new wave of attack missiles. if the enemy missiles strike a city, the colorful buildings will change to the solid color of the landscape.
The game continues until all cities are destroyed. Missile Command™ has no operator-selectable fixed time length. Thus a highly skilled player can play longer than the novice.
If the 2 PLAYER START pushbutton was pressed, at the beginning of each new wave of missiles the screen image will invert or turn 180° so the players can see it correctly. A flashing arrow indicates which score applies to the current player.
During the second wave, a “killer” satellite and/or bomber will appear on the screen, moving quickly and launching attack missiles at the bases and cities. Players get bonus points for shooting down the satellites or bombers.
The general approach for getting high point scores is fairly quickly discovered: try to launch your ABMs when the enemy missiles have just appeared at the top of the screen. Then they are clustered together, where one ABM can usually destroy several enemy missiles.
- High Score Initial Mode If a player’s score exceeds the minimum on the high score initial list, he or she may put up to three initials on this list at the end of the game. Spinning the Mini-Trak Ball™ control changes the letters (A thru Z and a blank are available). Pressing any fire switch will fix that letter on the screen, and move the choice to the next letter. If the player doesn’t enter his or her initials within 90 seconds, three blank spaces will be entered automatically.
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
“and Repair
All games require certain maintenance to keep them in good working order. Clean, properly maintained games will attract players and earn more profits.
The most important maintenance item is running the self-test every time you collect money from the cash box. Just looking at a game will not tell you if Mini-Trak Ball™ controls or light-emitting-diode switches are broken, or if LEDs have burned out. The self-test will inform you of any of these possible problems.
Second, you should regularly clean the outside of the game and the coin mechanisms. In addition, you will need to regularly lubricate the Mini-Trak Ball control: for details see this chapter.
A. Cleaning
The exterior of the game cabinet and the metal and glass surfaces may be Cleaned with any nonabrasive household cleaner. If desired, special coin machine cleaners that leave no residue can be obtained from your distributor. The large monitor shield is made of tempered glass and should be scratch-resistant: if cleaned without abrasive substances, you should hardly ever have to replace it.
B. Fuse Replacement
This game contains six fuses—all on the power supply assembly (not including the TV monitor fuses). Replace fuses only with the same type as listed in Figure 20 of this manual. For the monitor fuse data, see the Matsushita TV monitor manual, TM-153, or the Sanyo TV monitor manual, TM-157.
C. Opening the Control Panel
Prior to repairing or replacing any switch or the Mini-Trak Ball™ on the control panel, unplug the game. First open the game top. Then, to open the control panel, simply unscrew the two Allen-head screws at the top edge of the control panel. Once these screws are removed, the control panel will tilt towards you.
- LED Switch Replacement The light-emitting diode (LED) switches on the control panel have a very low failure rate. In case a switch should ever be suspect, first test it per the description that follows. To replace the switch, refer to Figure 9.
- Remove the wires from the suspected switch.
- Set multimeter to ohms scale. Set ohms scale to Rx 1, then zero the meter.
TO SERVICE OR REPLACE TRAK BALL ASSY., REMOVE THREE BLACK SCREWS, SELF-LOCKING HEX NUTS AND FLAT WASHERS.
To remove LED switch: Remove all wires from the faulty switch. Tum the switch counterclockwise while holding the black cone-shaped bushing on the outside of the control panel. Install a new switch using the reverse procedure. Reconnect the harness wires.
Figure 9 Opening the Control Panel and Replacing Switches
Disassemble in the order indicated. (Circled numbers match the steps described below.)
LUBRICATE HERE (5 PLACES)
Ball Replacement Coupler PCB Replacement
| 1. | First remove the entire Mini-Trak Ball assembly from the con- | 3. | Unplug the red connector on the coupler PCB. Remove the |
trol panel as shown in Figure 9. Now locate the three counter- two socket-head machine screws, flat and lock washers, and sunk machine screws in the acrylic top plate; remove these hex nuts from the coupler PCB.
| ‘screws, flat washers, and lock nuts. (When the assembly is in- | 4. | Remove the coupler PCB. |
| stalled, these three screws are right undemeath the control | 5. | When replacing this PCB assembly, be certain that the black |
panel.) metal encoding wheel turns freely between the two halves ot
| 2. | Lift off the acrylic top plate; remove and replace the ball. | the red photosensor device. |
Figure 10 Mini-Trak Ball™ Maintenance and Repair
2. Mini-Trak Ball™ Maintenance ys)
and Repair To maintain this control, you will only have to
| 3. | Connect muitimeter leads to appropriate LED | lubricate the bearings approximately every 2,000 |
switch contacts (see Figure 9 for designation of credits. The number of credits can be read off the switch contacts). coin counter, located on the floor of the cabinet, . next to the coin box. Use only 2 drops of 3-in-One®
| 4. | Check contacts (push and release the switch | oil in each of the ball bearings.-(Each Mini-Trak |
button) for closed and open continuity. Ball™ control has five bearings.)
- If the contacts do not operate sharply or always remain closed or open, then replace the LED For further instructions on how the replace the switch as outlined in the figure. ball or either coupler PCB, see Figure 10.
D
- TV Monitor Removal
monitor, follow steps 1 thru 5 below. Refer also to e@
Figure 11.
- Unlock and open the access panel.
- Unfasten and open the table top.
- Locate the 12-pin Molex connector between the game PCB and the TV monitor. Unplug this connector.
- Locate the four Phillips-head screws (one at each corner of the TV monitor screen) that attach the TV monitor to the cabinet. Remove these screws.
- Carefully lift the TV monitor chassis up and out of the cabinet.
Disassemble in the order indicated. (Circled numbers match the steps above.)
Figure 11. TV Monitor Removal @
REGULATOR! AUDIO I PCB
GAME PCB
Figure 12 Game and Regulator/Audio Il PCB Replacement
E. Printed-Circuit Board Replacement
You may wish to remove the game printed circuit board (PCB) or the Regulator/Audio Il PCB for service or inspection. To do this, refer to Figure 12 and proceed as follows:
1. e
e Game PCB Removal Unlock and open the access panel. Remove the 44-pin edge connector from the right side of the game PCB. Locate the Phillips-head screws that extend through the PCB and into the two wood blocks at the lock side of the access panel. Remove these two screws. Remove the PCB from the access panel by lifting up and pulling it out of the plastic PCB retainer at the hinge side of the access panel. Reinstall the PCB, making sure that the 44-pin edge connector is properly plugged in. Note that the connector is keyed to fit on only one way, So if it doesn’t slip on easily, don’t force it! A reversed connector will probably damage your game and will void the warranty. Check that the operation of the game is correct by performing the self-test. This is especially
Regulator/Audio II PCB Removal Unlock and open the access panel. Remove the five plug-in connectors. Locate the two Phillips-head screws that extend through the PCB and into the wood blocks at the top two corners of the PCB. Remove these two screws. Remove the PCB from the wall of the cabinet by pulling it up and out of the wood slot.
F. Game Operation
With this manual you received two large sheets that contain the wiring and schematic diagrams for your game. Sheet 1, Side A, includes information that explains the functions of the circuits and defines inputs and outputs.
Atari's Cocktail Missile Command™ is a microprocessor-controlled game. The microprocessor is mounted on the game PCB. The game PCB receives switch inputs from the control panel and coin mechanism. These inputs are processed by the game PCB and output to the TV monitor, Regulator/Audio II PCB, loudspeakers, and control panel.
The Regulator/Audio || PCB performs two functions: 1) it regulates the +10 VDC from the power supply to +5 VDC, and 2) it amplifies the audio output from the game PCB. The +5 VDC from the Regulator/Audio Il PCB provides most logic power to the game PCB. The audio output from the Regulator/Audio Il PCB directly drives the game speakers and is controlled by the volume control, mounted on the bracket inside the game.
The Power Supply is the source of all voltages in the game. These voltages are protected by three fuses (F3, F4 and F5) on the power supply chassis. The primary winding of the power supply transformer is protected by the fuses F1 and F2 on the power supply chassis.
Figure 13 illustrates the distribution of power in this game. Figure 14 illustrates the distribution of signals.
oS TV MONITOR COIN MECHANISM
100 VAC
POWER SUPPLY GAME PCB INTERLOCK SWITCH
REGULATOR! AUDIO II PCB
POWER ON/OFF SWITCH
Figure 13 Power Distribution ae
~ COLOR MONITOR SS START SWITCHES TRAK BALL SPEAKER : FIRE SWITCHES COIN MECHANISM i
CENTER FIRE Wy, RIGHT FIRE
TRAK BALL _V DIR & CK
START2LED
START2
START1LED
START
LEFT FIRE
TRAK BALL _H DIR & CK
REGULATOR! SLAM SWITCH ED AUDIO PCB GAME PCB VOLUME CONTROL SELF-TEST SWITCH COIN COUNTER
Figure 14 Signal Distribution
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
is Illustrated 'S Parts Lists
The purpose of this chapter is to provide you with the necessary information for ordering replacement parts for your game. Please note that, for simplicity, common hardware has been deleted from most of these parts lists. This includes screws, nuts, washers, bolts, etc.
The parts lists have been arranged in alphanumeric order. For example, all ‘‘A-” prefix numbers. come first. Following this are numbers in sequence evaluated up to the hyphen, namely 00-thru 99-, then 000598: thru approximately 110000-.
When ordering parts from your distributor, give the part number, part name, applicable figure number of this manual, and serial number of your game. This will help to avoid confusion and mistakes in your order. We hope the results will be less downtime and more profit from your game.
035852-01 (Crnr. Brkt.)
036078-01 (Monitor Bezel)
035850-01 (Latch Bracket).
62.039 (Start Switch)
A035916-01 (Start Sw/Brkt. Assy.)
78-3408 a (Latch)
Coin Acceptor— See Figure 21
48-004 (Speaker)
(Screw)
A036320-01 (Vol. Ctrl/Test Sw. Coin Sw. Assy) [>>
62.041 (Coin Sw.) 49.9932 (Wol. Cntrl.)
A035896-01 (Leg Assy.)
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific written permission of Atari, Inc., ‘Sunnyvale, CA. This drawing is only conditionally issued, and neither receipt nor possession thereo! confers or transters any right in, or license to use, the subject matter of the drawing or any design of technical information shown thereon, nor an ight to reproduce this drawing or any part thereo! Except for manufacture by vendors of Atati, Inc., and for manufacture under the corporation’s writ: ten license, no right to reproduce this drawing is, Granted of the subject matter thereof unless by written agreement with orwritten permission from the corporation, 000869.01 (Spkr. Grite) 82-8940 = 035851-01 (Hinge) 036077-01 (Glass Top) *S A036084.01 035867-02 (Sanyo Monitor) (4 -viic Overlay) A036083-01 (Matsu. Monitor)
A035906-01 (Top Support)
035854-01 (End-Pni. Grille) 034487-14 (Screw wiThread-Lock. Cpd.)
Mini-Trak Ball Assy.— See Figure 17
‘Control Panel Assy.— ~ See Figure 16
Z 68.002 (inter, Sw) 000268.02 QS 5 (Inter. Sw. Brkt.) oo ‘4036093-01 (Main Harness)
034536-04 (Foam Damper)
035848-01 (Leg Reinfmt. Plate) Reg /Audio Il PCB Assy.— See Figure 19 VF
A035843-01 (AC Harness)
Game PCB Assy.— NY See Figure 18 RIN Ve A034631-01 74.2110 (OnOft Sw.) (Lock) 035847.01 034537-01 : {Coin Box) (Vent. Grille) 69-001 035745-02 (Self-Test Sw.) {PCB Retainer) A002485-01 (Coin Counter) Power Supply Assy.— ‘See Figure 20
Figure 15 Cabinet-Mounted Assemblies A036080-xx B
Figure 15 Cabinet-Mounted Assemblies Parts List
Part No. Description
A002465-01 Coin Counter A007638-01 Slam Switch Assembly A034631-01 15 Amp @ 125V (10 Amp @ 250V) DPDT Toggle Switch A035843-01 AC Harness Assembly A035896-01 Leg Assembly A035906-01 Top Support Assembly A035916-01 Start Switches/Bracket Assy. (includes switches, stamped nuts, bushings and bracket) A035992-01 Strain-Relief Power Cord Assembly (for use in USA and Japan) yx) A036083-01 14” Matsushita Monitor Assembly (includes adapter harness and steel side supports) A036084-01 14” Sanyo Monitor Assembly (includes steel side supports) A036093-01 Main Harness A036320-01 Volume Control/Test Switch/Coin Switch Assembly (includes bracket) DP-152-01 Sheet 1 of Schematic Drawing Package DP-152-02 Sheet 2 of Schematic Drawing Package ST-152 Self-Test Label TM-152 Technical Manual for Cocktail Missile Command™ TM-153, Manual for Matsushita 14” Color Monitor TM-157 Manual for Sanyo 14” Color Monitor 19-9032 50-Ohm, 12'2-Watt, Wirewound Rheostat (Volume Control) 48-004 16-Ohm, 4-Watt, 4-Inch High-Fidelity Loudspeaker 62-039 SPDT Momentary-Contact Pushbutton Start Switch with Red Light-Emitting Diode 62-041 SPDT Momentary-Contact Pushbutton Coin Switch (for operator convenience) 68-002 30-Amp. Interlock Switch 69-001 DPDT Slide Switch (se/f-test) 71-2110 Panel Cartridge Lock Mechanism 7507017 Spacer for Mounting Printed-Circuit Boards 75-9910W0 15/32-32 Steel Stamped Nut (for start switch) 78-24012 5" Beaded Nylon Tie Wrap (for securing edge connector to Game PCB) 78-3408 Spring Draw Latch 78-6900402 Adhesive Foam Tape (for glass top) 82-8940 3/8-16 x 2%” Button-Head Hex Socket Machine-Thread Screw 000268-02 Interlock Switch Mounting Bracket 000869-01 Speaker Grille 007882-02 Interlock Switch Cover 033127-01 Black Molded Polycarbonate Switch Bushing 034487-14 10-32 x 7/8" Button-Head Hex-Head Machine-Thread Screw with Thread-Locking Compound 034536-04 Foam Vibration Damper 034537-01 Ventilation Grille 035745-02 18"-Long Plastic PCB Retainer 035845-01 Coin Box Lid 035847-04 Coin Box 035848-01 Leg Reinforcement Plate 035850-01 Latch Bracket 035851-01 Hinge 035852-01 Comer Bracket 035854-01 End-Panel Grille (2 per game) 035867-02 Bronze-Color Acrylic Overlay 035917-01 On/Off Switch Cover 036077-01 Glass Top with Graphics 036078-01 Cardboard Monitor Bezel q9- IS0O12 Pusn Barren FOF 99-1500! fist Burro ¢ 35g
Mini-Trak Ball Assy.— See Figure 17
62-041
ON 033127-01 036067-01
NOTICE TO ALL PERSONS RECEIVING THIS AWING CONFIDENTIAL: Reproduction forbidden without the specific written permission of Atari, Inc., ‘Sunnyvale, CA. This drawing is only conditionally issued, and neither receipt nor possession thereot confers or transfers any right in, or license to use, the subject matter of the drawing or any design oF technical information shown thereon, nor an right to reproduse this drawing or any part thereo! Except for manufacture by vendors of Atari, Inc., and for manufacture under the corporation's writ: teh license, no right to reproduce this drawing is granted or the subject matter thereof unless by Written agreement with or written permission from the corporation,
Figure 16 Control Panel Assembly A036076-01 A
Parts List
Part No. Description
A036095-01 Control Panel Harness Assembly 62-041 Pushbutton Switch with Black Cap (3 per game) 7507054 Flat Nylon Washer, 0.470” inside diameter x 0.968” outside diameter x 0.075" thick 75-99511 #10-24 Steel Stamped Nut 033127-01 Black Molded Switch Bushing 036067-01 Control Panel with Graphics
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
A035940-01 Figure 17 Mini-Trak Ball™ Assembly A 75-3608S (3 PLACES) (4 PLACES)
75-0468 (4 PLACES) — 03592701
75-9448 75-1606S (@PLACES) (4 PLACES) 75-8406 J
(4 PLACES) 75-0148, 72-8406
- hos - ~ |
na a f A f Hi J L,
A035220-01 . WY Not shown for clarity: Harness Assembly, part no. A036096-01 2 PACES! Lubrication Label, part no. 034168-01
72-8808 75-048S
Figure 17 Mini-Trak Ball” Assembly Parts List *
Part No. Description
A035220-01 Coupler PCB Assembly A036096-01 Harness Assembly 72-1606S #6-32 x 3/8" Cross-Recessed Pan-Head Cadmium-Plated Steel Machine Screw 72-8406 #4-40 x 3/8" Hex Socket-Head Cap Alloy Steel Machine Screw 72-8516 4-20 x 1” Hex Socket-Head Cap Alloy Steel Machine Screw 72-8808 #8-32 x 2" Hex Socket-Head Cap Alloy Steel Machine Screw 75-014S #4 Flat Plain SAE-Standard Zinc-Plated Steel Washer 75-016S #6 Flat Plain SAE-Standard Zinc-Plated Steel Washer 75-018S #8 Flat SAE-Standard Zinc-Plated Steel Washer 75-044S, #4 Zinc-Plated Steel Split Lock Washer 75-046S, #6 Zinc-Plated Steel Split Lock Washer 75-048S #8 Zinc-Plated Steel Split Lock Washer 75-944S, #4-40 Self-Locking Steel/Polymer Hex Nut 75-945S 4-20 Self-Locking Steel/Polymer Hex Nut 75-946S #6-32 Self-Locking Steel/Polymer Hex Nut 85-1808B #8-32 x 1%” Socket Cap Flat Countersunk-Head Black-Oxide Steel Screw 034168-01 Label with Lubrication Instructions 035926-01 Base Plate 035927-01 Top Plate (Metal) 035928-01 Top Plate (Acrylic) 035929-01 Corner Post 035930-01 End Post 035931-01 Roller Shaft 035932-01 Standoff 035933-01 Adjustable Post 035934-01 Spacer 035935-01 Angle Bracket 035936-01 Mini-Trak Ball™ 035937-01 Bearing 035938-01 Encoding Wheel
SEE DETAIL
or =03 VERSION ray BUS +5¥ BUS ev Bu
2708 ENABLE SAt6 ous S3GE ENABLE
DETAIL TWP. 6PL
SCALE: NONE
Z3PL.
SPLIT PAD CONNECTIONS AS DETAILED ARE
APPLICABLE TO USE OF 83IGE'S.USE OF 2708'S
REQUIRE BRIDGING OF OPEN PADS AND CUTTING
‘OF CONNECTED PAOS.
SPL. FARSIDE NOTICE TO ALL PERSONS RECEIVING THIS DRAWING ing is only con possession th
55 by ten permission from the corp
D Figure 18 Game PCB Assembly A035467-01 thru -04
Figure 18 Game PCB Assembly Parts List
Part No. Description (Reference Designations and Locations in Bold)
| C012294-01 | Audio /O N-Channel MOSILSI Custom Chip | (P8/9) |
21-101683 .068 uf, + 10%, Radial-Lead Epoxy-Dipped 100V Mylar Capacitor (C65-68)
| 24-250105 | 1 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor | (C76-79, 98, 100-104) |
| 24-250106 | 10 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor | (C20, 23, 39) |
| 24-250107 | 100 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor | (C9, 10, 46, 57, 91) |
| 24-250226 | 22 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor | (C90) |
| 27-250103 | .01 uf Ceramic-Disc 25V Radial-Lead Capacitor | (C76-79) |
28-101102 1000 pf Epoxy-Dipped 100V Radial-Lead Mica Capacitor (C99, 105)
| 29-088 | -1 uf Ceramic-Disc 25V Radial-Lead Capacitor | (C1-8, 13-16, 18, 19, 21, 22, 30, 38, 43-45, 47-56, |
58-64, 69-75, 80-89, 92-97, 106) 31-1N914 75V Type-1N914 Switching Diode (CR2) 34-2N3643 Type 2N3643 NPN Switching Transistor (Q8) 34-2N6044 Type 2N6044 NPN Darlington Transistor (Q1-3)
| 37-4584B | Type 14584 Integrated Circuit | (C9, C11) |
| 37-7400 | Type 7400 Integrated Circuit | (C5, D8) |
| 37-74S00 | Type 74S00 Integrated Circuit | (A8) |
| 37-7404 | Type 7404 Integrated Circuit | (E6, K7) |
| 37-74HO4 | Type 74H04 Integrated Circuit | (B6) |
| 37-74S04 | Type 74804 Integrated Circuit | (D7) |
| 37-7407 | Type 7407 Integrated Circuit | (N11) |
| 37-74LS08 | Type 74LS08 Integrated Circuit | (H7) |
| 37-7408 | Type 7408 Integrated Circuit | (R2, J6) |
| 37-74S08 | Type 74S08 Integrated Circuit | (M3) |
| 37-74LS10 | Type 74LS10 Integrated Circuit | (E3) |
| 37-7410 | Type 7410 Integrated Circuit | (B5) |
| 37-74LS14 | Type 74LS14 Integrated Circuit | (D3) |
| 37-7414 | Type 7414 Integrated Circuit | (J9) |
| 37-7427 | Type 7427 Integrated Circuit | (B7) |
| 37-7432 | Type 7432 Integrated Circuit | (C3, R5) |
| 37-74LS32 | Type 74LS32 Integrated Circuit | (J7) |
| 37-74832 | Type 74S32 Integrated Circuit | (C4, L5, K6) |
| 37-7442 | Type 7442 Integrated Circuit | (N2, E8) |
| 37-7474 | Type 7474 Integrated Circuit | (H6, A7, E7, F7, J8, A9) |
| 37-74874 | Type 74S74 Integrated Circuit | (A6, B8, C8) |
| 37-7475 | Type 7475 Integrated Circuit | (R7) |
| 37-7493 | Type 7493 Integrated Circuit | (D4) |
| 37-74109 | Type 74109 Integrated Circuit | (D6) |
| 37-74125 | Type 74125 Integrated Circuit | (R6) |
| 37-74LS139 | Type 74LS139 Integrated Circuit | (P2, M5) |
| 37-74LS153 | Type 74LS153 Integrated Circuit | (F5, H5, J5, K5, P7) |
| 37-74153 | Type 74153 Integrated Circuit | (F3, H3, J3, K3) |
| 37-74LS157 | Type 74LS157 Integrated Circuit | (H2, J2, K2, L2, M2, M7, D9) |
| 37-74S157 | Type 748157 Integrated Circuit | (E4) |
| 37-74160 | Type 74160 Integrated Circuit | (E5) |
Ce Figure 18 Game PCB Assembly, continued Parts List
Part No. Description (Reference Designations and Locations in Bold)
| 37-74163 | Type 74163 Integrated Circuit | (D5) |
| 37-74LS163A, | Type 74LS163A Integrated Circuit | (R4) |
| 37-74LS166 | Type 74LS166 Integrated Circuit | (P6) |
| 37-74175 | Type 74175 Integrated Circuit | (L8) |
| 37-74LS175 | Type 74LS175 Integrated Circuit | (C7) |
| 37-74LS191 | Type 74LS191 Integrated Circuit | (K8, K9) |
| 37-74191 | Type 74191 Integrated Circuit | (A4, B4) |
| 37-74LS195 | Type 74LS195 Integrated Circuit | (M6, N7) |
| 37-74LS244 | Type 74LS244 Integrated Circuit | (A/B1, E2, F2, P5, L9, M9, P10, B/C1, N/P3) |
| 37-74LS251 | Type 74LS251 Integrated Circuit | (N5) |
| 37-74S260 | Type 74S260 Integrated Circuit | (A5) |
| 37-74LS273 | Type 74LS273 integrated Circuit | (N6, F9) |
| 37-LM324 | Type LM324 Integrated Circuit | (N10) |
| 38-MV5053 | Type MV5053 Light-Emitting Diode | (CR1) |
62-001 SPST Pushbutton Switch (B3) 66-118P1T 8-Station Single-Throw, Dual-Inline-Package Bit Switch (R8, R10) 79-42C24 24-Contact Medium-Insertion-Force Integrated Circuit Socket (For -01 and -03 PCB Assemblies: D1, E1, F1, H1, J/K1, K/L1, M1, M/N1, N/P1, R1, R3; For -02 and -04 PCB Assemblies: H1, JiK1, K/L1, LM1, N/P1, R1) 79-42C40 40-Contact Medium-Insertion-Force Integrated Circuit Socket (C2, P8/9) 81-4302 Nylon Snap-In Fastener
| 90-123 | 10.000 MHz, + .005%, Crystal | (¥1) |
90-6013 Microprocessor (C2) «90-7005 Random-Access Memory (L7) 020670-01 Test Point
| (2935826-0 | Programmable Read-Only Memory | (L6) |
£4001
110000-103 110000-152 110000-220 110000-221
110000-222 110000-332 110000-270 110000-331
110000-391 110000-471 110000-472 110000-682
110000-822 122004-224 137002-001 137149-001 Random-Access Memory (F4, H4, J4, K4, L4, M4, N4, P4) 1K Ohm, +5%, %4W Resistor (R1, 2, 4, 13, 16, 21-26, 39, 60, 61, 73, 74, 85, 95, 109-122)
10K Ohm, +5%, %4W Resistor (R3, 17-20, 30-38, 66-71, 83, 84, 86-88, 93, 94, 96-100) 1.5K Ohm, +5%, %4W Resistor (R79) 22 Ohm, +5%, YaW Resistor (R46, 47, 82) 220 Ohm, +5%, VW Resistor (R72)
2.2K Ohm, +5%, YW Resistor (R76) 3.3K Ohm, +5%, YW Resistor (R56-59, 89-92) 27 Ohm, +5%, %4W Resistor (RS§-12, 27-29) 330 Ohm, +5%, %4W Resistor (R14, 15, 78)
390 Ohm, +5%, %4W Resistor (R45, 81) 470 Ohm, +5%, %4W Resistor (R40-44, 48-55, 80) 4.7K Ohm, +5%, %W Resistor (R75) 6.8K Ohm, +5%, %W Resistor (R101-108)
8.2K Ohm, +5%, %W Resistor (R77) .22 uf Ceramic-Disc 25V Radial-Lead Capacitor (C24-29, 31-37, 40-42) Type 74S86 Integrated Circuit (L3) Type 74LS11 Integrated Circuit (F6, N3)
For remaining memory components and their part numbers, see list on next page.
Figure 18 Game PCB Assembly, continued
Memory Components and Their Equivalents Parts List
(Locations Shown in Bold)
-01 P.C. Boards 02 P.C. Boards 03 P.C. Boards 04 P.C, Boards (mostly PROMs) (ROMs) (mostly PROMs) (ROMs)
03581201 KILI 03581202 K/L1 03682201 KILI 03582202 KILI 035813-01 F1 035813-02 Ft
03682301 LIM1 03582301 UIM1 03682302 UM1 03682302 UM1
035816-01 NIP1 03581602 NIP1 035824-01 NIP1 03582402 NIP1 03681701 MIN1 03881702 MIN1
03681801 RI 035818-02 RI 035825-01 RI 036825-02 RI 036819-01 R3 03581902 R3
036808-01 Ht 03680802 H1 03682001 H1 03582002 H1 036809-01 D1 03580902 D1
03681001 J/K1 03581002 JIK1 038821.01 JIK1 03682102 JIK1 03681101 £1 03681102 1
anon
3013 3LIS0dd0 NO guv NWOHS S29V4L NOTICE TO ALL PERSONS RECEIVING THIS AWING: oF CONFIDENTIAL: Reproduction forbidden without the specific written permission of Atari, Inc., ‘Sunnyvale, CA. This drawing is only conditionally. issued, and neither receipt nor possession thereot confers or transfers any right in, of license to use, the subject matter of the drawing or any design of technical information shown thereon, nor any right to reproduce this drawing or any part thereof. Except for manufacture by vendors of Atari, Inc., and for manufacture under the corporation's writ ten license, no right to reproduce this drawing is, granted or the subject matter thereof unless by written agreement with or written permission from the corporation.
Figure 19 Regulator/Audio II PCB Assembly A035435-02
Figure 19 Regulator/Audio Ii PCB Assembly Parts List
Part No. Description (Reference Designations and Locations in Bold)
| 12-52P7 | 2.7 Ohm, + 5%, 1W Resistor | (R5) |
| 16-54P0 | 4 Ohm, + 5%, 5W Wirewound Resistor | (R25) |
| 19-100P1015 | .1. Ohm, + 3%, 7W Wirewound Resistor | (R24) |
19-315102 1K Ohm Vertical PCB-Mounting Cermet Trimpot (R8) 24-250106 10 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (C5, 15) 24-250108 1000 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (C9, 10, 13) 24-250477 470 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (C1, 4, 12) 24-250478 4700 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (C29)
| 24-250108 | 1000 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor | (C13) |
| 24-250477 | 470 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor | (C1, 4, 12) |
24-350226 22 uf Aluminum Electrolytic Fixed Axial-Lead 35V Capacitor (C24, 31)
| 24-350338 | 3300 uf Aluminum Electrolytic Fixed Axial-Lead 35V Capacitor | (C9, 10, 18, 19) |
24-500105 1 uf Aluminum Electrolytic Fixed Axial-Lead 50V Capacitor (C22, 23) 27-250102 .001 uf Ceramic-Disc 35V Radial-Lead Capacitor (C2, 7, 16) 27-250103 .01 uf Ceramic-Disc 25V Radial-Lead Capacitor (C5, C14) 29-088 .1 uf Ceramic-Disc 25V Radial-Lead Capacitor (C3, 11, 20, 21) 31-A14F 50V 2.5A Miniature Axial-Lead High-Current Rectifier (CR1, 4-8)
| 33-TIP32 | PNP Power Transistor, Type TIP32 | (Q2) |
| 34-2N3055 | NPN Silicon. Transistor, Type 2N3055 | (Q3) |
| 37-LM305 | 5V Linear Voltage Regulator | (Q1) |
| 37-7812 | +12V Voltage Regulator, Type 7812 | (Q8) |
| 37-7905 | —5V Voltage Regulator, Type 7905 | (Q9) |
72-1608C #6-32 x Ye" Cross-Recessed Pan-Head Corrosion-Resistant Steel Machine Screw 75-F60405 #6-32 x 4” Binder-Head Nylon Screw 75-99516 #6-32 Nut/Washer Assembly
| 78-16008 | Thermally Conductive Compound | (Q3) |
| 78-16014 | Thermally Conductive Compound | (Q2, 5, 7-9) |
| 79-58306 | 6-Position Connector Receptacle | (J6, 9) |
79-58308 9-Position Connector Receptacle (J7) 79-58346 12-Position Connector Receptacle (J10)
| 79-58354 | 4-Position Connector Receptacle | (J8) |
020670-01 Test Point 034531-01 Heat Sink
| 110000-010 | 1 Ohm, + 5%, “%W Resistor | (R10, 19) |
| 110000-100 | 10 Ohm, + 5%, %W Resistor | (R11, 20, 29, 30) |
| 110000-101 | 100 Ohm, + 5%, 1%4W Resistor | (R4, 12, 22) |
| 110000-102 | 1K Ohm, + 5%, %4W Resistor | (R27, 28) |
| 110000-103 | 10K Ohm, + 5%, %W Resistor | (R13, 14) |
| 110000-271 | 270 Ohm, + 5%, %W Resistor | (R1) |
| 110000-330 | 33 Ohm, + 5%, %W Resistor | (R3) |
110000-392 3.9K Ohm, + 5%, YW Resistor (R6)
| 110000-562 | 5.6K Ohm, + 5%, %W Resistor | (R32, 33) |
| 110000-752 | 7.5K Ohm, + 5%, %4W Resistor | (R7) |
| 110001-221 | 220 Ohm, + 5%, ¥2W Resistor | (R9, 21) |
| 116000-220 | 22 Ohm, + 5%, 10W Wirewound Resistor | (R31) |
122004-224 .22 uf Ceramic-Disc 25V Capacitor (C6, 8, 15, 17)
| 137151-002 | Type TDA2002A 8W Linear Audio Amplifier Integrated Circuit | (Q5, 7) |
TOP VIEW a 034482.01
(Cc
78-70501S¢ 462017002
©
29-053
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the Specific written permission of Atari, Inc., Sunnyvale, CA. This drawing is only conditionally’ issued, and neither receipt nor possession thereof conters or transfers any Fight in, or license to use, the subject matter of the drawing of any design or technical intormation shown thereon, nor any Tight to reproduce this drawing or any oart thereot. Except for manufacture by vendors of Atari, Inc., and for manufacture under the corporation's written, license, no right 10 reproduce this drawing is granted or the subject matter thereof uniess by written agreement with or written permission from the corporation.
BOTTOM VIEW
Figure 20 Power Supply Assembly for Color Raster-Scan Games A036099-01 A
Figure 20 Power Supply Assembly for Color Raster-Scan Games Parts List
Part No. Description
A006555-01 Rectifier Printed Circuit Board Assembly A036098-01 Transformer and Harness Assembly (includes Shielded Power Transformer) A034629-01 AC Harness Assembly A034630-01 RFI Filter Assembly A035674-01 Voltage Plug Assembly (set of four plugs) 29-053 26,000 uf 15V Electrolytic Capacitor 46-2013002 3-Amp. 250V 3AG Slow-Blow Glass Cartridge-Type Fuse 46-2017002 7-Amp. 250V 3AG Slow-Blow Glass Cartridge-Type Fuse 78-2708 Nylon Type 6/6 Hole Bushing with 5/8” Inside Diameter x 55/64” Outside Diameter x 1%" Thick 78-70501SC. 2”-Diameter Capacitor Mounting Bracket 79-15021001 2-Circuit Single-Row Terminal Block 79-3206 5-Position 3AG Fuse Block with 4” Quick-Disconnect Terminals 79-4411006 Panel-Mounting Non-Indicating 3AG Cartridge-Type Fuse Post 034544-01 Fuse Block Gover AS 142001-001 Shielded Power Transformer Only (with isolation windings)
035872-01 SS
° | 71-104xx
i A Ly | | a \ jo ‘ Ib) | \
| | | \ | NOTICE TO ALL ERRONS | RECEIVING THIS: | ||
| By | | | ‘ | Z | CONFIDENTIAL: Reproduction forbidden without |
Dy 4 the specific written permission of Atari, Inc.,
| Ey | ~G& | Eauieneheencermneuciatot |
v confers or transfers any right in, or license to use, SS) the subject matter of he arawing or any design of technical information shown thereon, nor any Fight to reproduce this drawing or any part thereof. 8 Except for manufacture by vendors of Atari, Inc., and for manufacture under the corporation's writ- % ten license, no right to reproduce this drawing is Granted or the subject matter thereof unless by Written agreement with or written permission from the corporation.
a Figure 21. Coin Acceptor Mount Assembly A035912-xx D
Parts List
Part No. Description
| A035837-01 | Coin Acceptor Face Plate | (25¢) |
| A035837-02 | Coin Acceptor Face Plate | (100 Yen) |
| A035837-03 | Coin Acceptor Face Plate | (70 Pence) |
| A035837-04 | Coin Acceptor Face Plate | (1 DM) |
| A035837-05, | Coin Acceptor Face Plate | (2 DM) |
| A035837-06 | Coin Acceptor Face Plate | (100 Lire) |
| A035837-07 | Coin Acceptor Face Plate | (7 Kr Swedish) |
| A035837-08. | Coin Acceptor Face Plate | (20¢ Australian) |
| A035837-09 | Coin Acceptor Face Plate | (1 Fr French) |
| A035837-10 | Coin Acceptor Face Plate | (5 Fr Belgian) |
A035838-01 Coin Mechanism Harness 035872-01 Coin Acceptor Mount
| 71-10425CU | Coin Acceptor | (25%) |
| 71-104100YJ | Coin Acceptor | (100 Yen) |
| 71-10410PE | Coin Acceptor | (10 Pence) |
| 71-10401MG | Coin Acceptor | (7 DM) |
| 71-10402MG | Coin Acceptor | (2 DM) |
| 71-104100LI | Coin Acceptor | (700 Lire) |
| 71-10401KS | Coin Acceptor | (1 Kr Swedish) |
| 71-10420CA | Coin Acceptor | (20¢ Australian) |
| 71-10401FF | Coin Acceptor | (1 Fr French) |
| 71-10405FB | Coin Acceptor | (5 Fr Belgian) |
= Cocktail Missile Command 1st printing
YOUR COMMENTS, PLEASE!
Your comments will assist Atari in improving the usefulness of our publications. They are an important part of preparing for revisions of manuals and parts catalogs. No postage stamp is necessary if mailed in the U.S.A.
If you have any technical questions about certain Atari or Kee Games products, or are requesting additional publications, we will immediately forward your note to the appropriate person.
Page: Comments:
Fill in if you wish a reply:
Name Firm O Distributor
Address. UO Operator City State Zip O Other.
First fold
BUSINESS REPLY MAIL
FIRST CLASS PERMIT NO. 1004 SUNNYVALE.CA
POSTAGE WILL BE PAID BY ADDRESSEE
Atari, Inc. Attn.: Field Service/Coin-Op Division P. O. Box 427 Sunnyvale, California 94086 No Postage Necessary if mailed in the United States
Second fold
eBpe siyy eday swiol4 Cut along this line ~*~]
Bes BER ES BEN WER 2S
h
a
Pdiee Sata Natee! Natue) ated Naked Satee, Salad Na
Warranty
Seller warrants that its printed circuit boards and parts thereon are free from defects in material and workmanship under normal use and service for a period of ninety (90) days from date of shipment. Seller warrants that its television monitors (in games supplied with monitors) are free from defects in material and workmanship under normal use and service for a period of thirty
- days from date of shipment. None of the Seller's other products or parts thereof are warranted.
if the products described in this manual fail to conform to this warranty, Sellers’ sole iiability shall be, at its option, to repair, replace, or credit Buyer's account for such products which are returned to Seller during said warranty period, provided:
{a) Seller is promptly notified in writing upon discovery by Buyer that said products are defective,
- Such products are returned prepaid to Sellers’ plant; and
- Seller's examination of said products discloses to Seller's satisfaction that such alleged defects existed and were not caused by accident, misuse, neglect, alteration, improper repair, installation or improper testing.
In no event shall Seller be liable for loss of profits, loss of use, incidental or consequential damages.
Except for any express warranty set forth in a written contract between Seller and Buyer which contract supersedes the terms of this order, this warranty is expressed in lieu of all other warranties expressed or implied, including the implied warranties of merchantability and fitness for a particular purpose, and of all other obligations or liabilities on the Seller’s part, and it neither assumes nor authorizes any other person to assume for the Seller any other liabilities in connection with the sale of products uhder this order.
The use of any non-Atari parts may void your warranty, according to the terms of the warranty. The use of any non-Atari parts may also adversely affect the safety of your game and cause injury to yourself and others. Be very cautious in using non-Atari-supplied components with our games, in order to insure your safety.
Atari distributors are independent, being privately owned and operated. In their judgment they may sell parts or accessories other than Atari parts or accessories. Atari cannot be responsible for the quality, suitability or satety of any non-Atari part or any modification including labor which is performed by such distributor.
This document is and contains confidential trade secret information of Atari, Inc.
This document is loaned under confidential custody for the sole purpose of operation, maintenance or repair of Atari equipment and may not be used by or disclosed to any person for any other purpose whatever, and remains the property of Atari, Inc.
Neither it nor the information it contains may be reproduced, used, or disclosed to persons not having a need to know consistent with the purpose of the loan, without written consent of Atari, Inc. ©
£
©
ISN
ATARI
ATARI INC 1265 SOEEGLS AVENUE P.O. BOX 4
SUNNYVALE, CALIFORNIA 94086
408/745-2000 ¢ TELEX 35-7488 Qi were: commricaion igen