CATHODE RAY TOMES

Arkanoid 2 Revenge of DOH

Arkanoid 2 Revenge of DOH (Romstar Inc., 1987) · Manual · 16 pages · 18 sections · original scan

Page 1

ROMSTAR inc.

ARKANOID 2, REWENGE OF DO

Instruction Manual

Romstar, Inc.

Page 2

WARRANTY, REPAIR AND RETURN POLICY

*45 DAY FULL PARTS WARRANTY.

*60 DAY FULL ELECTRONICS WARRANTY (SEE RMA BELOW).

MINIMUM $40.00 SERVICE CHARGE FOR ALL NON-WARRANTY REPAIRS OR

RETURNS.

ANY UNAUTHORIZED NON-FACTORY REPAIR OR ATTEMPTED REPAIR VOIDS

WARRANTY.

(“ALL WARRANTY PERIODS BEGIN ON THE DATE OF PURCHASE FROM ROMSTAR)

RETURN MERCHANDISE AUTHORIZATION — (RMA)

ALL RETURNED MERCHANDISE MUST HAVE AN RMA NUMBER CLEARLY VISIBLE ON THE OUTSIDE OF THE PACKAGE.

ALL RMA NUMBERS MUST BE OBTAINED FROM ROMSTAR BY AN AUTHORIZED ROMSTAR DISTRIBUTOR. (PLEASE HAVE ROMSTAR SERIAL NUMBER AVAILABLE WHEN CALLING FOR AN RMA #).

ALL PC BOARDS RETURNED TO ROMSTAR WITHOUT AN RMA NUMBER WILL NOT BE ACCEPTED.

ROMSTAR WILL SHIP ADVANCE REPLACEMENT BOARDS TO DISTRIBUTORS OR AT DISTRIBUTORS REQUEST, DROP-SHIP BOARDS DIRECT TO THE OPERATOR.

ADVANCE REPLACEMENT BOARDS WILL BE BILLED TO THE DISTRIBUTOR UNTIL RECEIPT OF A RETURNED BOARD BY ROMSTAR AT WHICH TIME A CREDIT WALL BE

ISSUED.

ALL REPAIRS AND/OR REPLACEMENTS WILL 8E SHIPPED BY ROMSTAR WITHIN 24 HOURS OF RECEIPT OR REQUEST. (SUBJECT TO AVAILABILITY OF BOARDS).

FOR ANY ROMSTAR PRODUCT PURCHASED AFTER 3/1/86, A ROMSTAR WARRANTY CARD MUST BE ON FILE FOR EACH BOARD TO FACILITATE REPAIR & RETURN.

ROMSTAR WILL REPAIR OR REPLACE ROMSTAR PCB's FOR A MINIMAL CHARGE FOR A PERIOD OF | YEAR.

ANY QUESTIONS CONCERNING THESE POLICIES SHOULD BE DIRECTED TO DARRYL WILLIAMS, SENIOR TECHNICIAN OR SHAWN ZENKER, OPERATIONS OFFICER.

Page 3

Installing and Servicing Your

ARKANOID 2

REVENGE OF DOR

New Game Package

Table of Contents

New: Game:Packageé Contents... 2004 ees reg eae ee ele cas Hee 2

Power and Monitor Requirements «2.0.6.7. Gam. bas oi oy eo ake ye 2 Recommended Tools and Supplies....... gino. Weee) oP vce he bee OR eG een? 3 Dip SWC TaD OSs Fes to a eae ie hee tre wate lg SEE rae tl 384 Game-OPeration 6.30 OR BREN EY on ale HR el Gaiam. 8S eae es + 5 JeistallatiGrr PrGeOer ese. ies seem wrs vis ehe eee ane + ae quays wives eR eT 9 6

Control Panel POSIGRING 52s isch bees sss eles dS CER a ee 1 TEC ASTI PS aig race wpa tbcRee GR ws Say sleyese eyeps ce ome aBE elaine reece Saran eeaeeTE graces 12-13

Main Harnéss Connections: <2... sie ee Hep ee ios 6 See a ae outside back cover

haglo fg

Page 4

NEW GAME PACKAGE CONTENTS

Main Printed Circuit Board (PCB) Monitor Bezel Set Legs, Bolts, & Spacers Connecting Wire Harness Arkanoid Control Assembly Player Button Assemblies ae Een Marquee Control Panel Overlay Plex Control Cover Set Side Graphics Set Play Instructions & Function Labels Service and Installation Manual

Note: Replacement accessories availabie through your exclusive Romstar distributor

MONITOR REQUIREMENTS

i +5 VDC | 7 amp minimum

; +12 VDC } Famp minimum POWER REQUIREMENTS |

Verticle Mount Raster Scan Negative Composite Sync eran eterno rere aR A

Page 5

Stop!

Berens. it complete?) ply all the required voltages, .

Before You Get Start d

“Does your fnew ga game patcaenen “2. Isthe game you have chosen totransfor mable for the new game?

Note: Some games, {i.¢. Ms. Pac Man, G etc.) regulate their voltages on the main PC.B. This makes the existin supply inefficient. These games’ will require a change in power supply fo: your new game. Many game supply houses can offer you a switching regulated power supply fora relatively low cost.
  • Is the monitor configuration compatible?.In most games it is rather difficult to change the monitor from a vertical mount to a horizontal mount. We recommend you choose a game cabinet with the same mount as your new game requires.
  • Do you have the necessary tools? (See the recommended tool list)

Caution

F.C.C. Regulation Compliance Operation of this equipment in a residential area is likely to cause interference

  • in which case, the user at his own expense, will be required to take whatever measures may be required to correct the interference.

Recommended Tools and Supplies

ROMSTAR new game package. Phillips and Slot Screwdrivers Socket Set Enthusiastic Attitude Wire Cutters and Strippers Pliers or Channel Locks Planning and Careful Thought Electric Drill 3/32" © 1/4" © 7/16” Drill Bits 1/4” Plex Bit 1-3/16” Chassis or Sheet Metal Punch 1 1/4” Plex Hole Saw Glass of Water and a Snack Small File Razor Knife and Sharp Blades Straight Edge Patience Common Sense

Dip Switch Tables

Optimize Your Profits Painting Supplies (if you do your own i painting) | Paint Brush and Paint (don’t forget _ the primer) Paint Roller and Pan | Sand Paper Putty Knife and Wood Putty A Good Night’ Sleep Staple Gun and Staples Soldering Iron and 60/40 Resin Core older Vacuum Cleaner Assorted Fastening Hardware Shrink Tubing: 3/32” © 1/8” © 3/16" Masking Tape 3 1/2" OR 4” Wire Ties Spray Window Cleaner and Rags (baby diapers work GREAT!)

Thorough Research shows that two and a half minute games both satisty I players and also keep the quarters flowing. If games aren't running about two and a half minutes long, then collections probably aren't at their peak. You'll want to tailor your game to your location. The trick is to adjust a’few DIP switches. (See the chart in this book.) It’s easy!

Page 6

Game Style" Upright Monitor i Normal Invert

Test Normal Game

Test Mode

Attract Sound on

off Coin 1-Coin 1-Play

1-Coin

Dip Switch “B”

Difficulty Normal

Hard

Very Hard 100 K / 200K 100 K ONLY 50 K Only 50K/ 150K Number of VAUS

NOT USED

Continue

  • Denotes Recommended Settings
Page 7

—__Game Operation

Revenge af

IN 30 ROUNDS OUT OF THE TOTAL 34, THE PLAYER CAN CHOOSE EITHER RIGHT OR LEFT TYPE OF THE NEXT ROUND WHICH DIFFERS IN DIFFICULTY HIS CHOICE DEPENDS WHICH SIDE OF THE SCREEN VAUS IS LOCATED WHEN THE LAST BLOCK IS DESTROYED.

Page 8

Installation Procedures

Something To Think About

Your final product will be a new game. You have made a wise decision to transform a game that has seen better days in the all important cash box into a mew game. This is by far the most cost effective alternative to maximize the return of your initial investment. All you provide is the cabinet with a power supply and a monitor. Oh yes, you will need a touch of elbow grease. And that's it! We provide the rest. The end result is... amew game ata very low cost. Fact: Spend alittle time on the cabinet’s appearance (i.e. marquee, control panel and cabinet graphics). With a little paint, some wood putty and new lights, you will raise the profits of any game. . .especially with the introduction of anew game package. The new game look should always apply to the inside of your game as well as the outside. A few wire ties and shrink tubing on your harness; some fastening hardware on your subassemblies and a sweep with the ol’ vacuum cleaner will ensure that unnecessary glitches do not occur. Remember: You are creating anew game . If you have any questions or just need some advice on any of your new game

  • transformations, don’t hesitate in giving a member of our technical staff a call.

Let’s Get Our Hands Dirty

Preparing the Original Game for the New Game

Remove the following:

1,Main logic board(s}4.Monitor Bezel
2.Control panel5.Marquee
3.Monitor plexiglass6.Graphics

| would recommend painting your cabinet to give it a fresh new look. You may consider having an auto body shop take care of your painting needs.

If your cabinet has wood grain sides; remove old graphics and adhesive (adhesive may be removed with lacquer thinner. : If you intend to use your original plexiglass, be sure it is in mint condition or it should be replaced. Thoroughly clean out your cabinet.

Page 9

Time To Install Your New Goodies

Before You Start. ..Remember DO NOT Do This Work With The Power On!

Logic P.C.B. Cage

Mount the logic board securely (away from power supply). A Mark and drill pilot holes (3.32”). B Install the P.C.B, into cabinet. Use feet and spacers supplied and adjust them so that the screws will go through the holes in the cabinet.

Wire Harness

Attach the wire harness connector to the main logic board. CAUTION: Sometimes the connector is not keyed and it is very easy to install it reversed on the logic board. Even if it is keyed, always triple check to be sure the wire inputs were connected correctly to the connector and the connector to the logic board.

Connecting the Wire Harness to the Existing Wires When you hook up the control panel, power supply, monitor or other | subassemblies that remain in the game cabinet to your new wire harness, try and use their existing secondary connectors. 1, Cut the original wire approximately three inches from the original connector. Strip off about one half inch of insulation.

  • Solder the new wire designated for that position to the original wire you just stripped.
Warning: DO NOT JUST TIE THE WIRES TOGETHER. THIS CAN CAUSE NAGGING INTERMITTENT PROBLEMS THROUGH LOOSE'CONNECTIONS OR OXIDATION OR BOTH. Always take the time to do it right.
  • Melt shrink tubing around all your in-line wire connections. Do not use electrical tape. Tape could unravel over a period of time due to the cabinet heat and cause you a great deal of trouble.
  • Use wire tie wraps, and secure the cable to the cabinet whenever it seems necessary. Remember this is anew game , not a sloppy conversion.

Power Wires

  • Connect the wires that are designated for your power supply. You will need a supply of +5V, +12V & ground. Your new game package may not require all of the voltages that were used in the original game. Tie off any unused wires.
  • You will notice that you probably have more than one wire for each voltage. It is a good idea to use all wires supplied (double up if it is necessary). This will help to ensure that you don't overload the edge connector pins and cause them to “burn”.

EAU, FAA aia Nea eS Ca

Page 10

You will be connecting the wires designated for the RED, GREEN & BLUE video guns along with the SYNC & GROUND wires. .

NOTE... .CONCERNING SYNC: Your new game only calls for one sync wire connection, this is called composite syne (horizontal and vertical tied together). This composite sync is also negative. Most monitors have supply positions for both negative and positive sync. You can check your monitor manual or call our technical department for assistance.

Speaker Wires Find the two wires that are designated for the speaker and hook ‘em on up.

Coin Door Wires ‘

Connect the designated wires to the°coin switches and meter. (See tech tips}

  • Youcan connect your door lamps to the unused -5V power supply. Some games have separate power outputs for the coin door lamps.
  • Be sure to clean and lubricate your old coin mechanisms. Keep the money coming in.

GUESS WHAT?

You are almost done with the electrical connections of your new game. All you have left is the control panel wiring. But we are going to hold off on that for right now. We have a few other things we need to do first. So why don’t you go ahead and get yourself a drink of water and stretch your legs. W/hen you return, we can take a fresh look at your progress and then move forward.

Smoke Test

What Test?

Don't worry. All this means is that you are ready to apply power to the system for the first time and you pray that there will be no smoke from a simple oversight. You are just about ready to power up the logic board. But first we need to recheck your work.

  • Carefully inspect the game for loose power wires, exposed connections and extra fastening hardware.
  • Make sure the logic board, monitor and power supply are securely fastened in place.
  • Double check the connectors to be sure they are wired and connected properly.
  • Set the dip switches on the logic board to the factory recommendations. (Refer to page 5.) Also, be sure you set the dip switches for “DEMO WITH SOUND”. This will enable you to hear as well as see that your new PC.B. is functional.
Page 11

Time to Apply Power: Look and smell for smoke. (TURN OFF LITE IF ANY IS NOTICED}

  • Listen for game sounds. If after one minute you have not heard any sounds: A] Check for proper dip switch settings. B) Adjust volume control and check speaker connections. C) Check the +12V power supply to the logic board.
NOTE: If you do get sounds, but they are a little fuzzy, switch the wires around on the speaker.
  • How is the monitor image? A) Is the picture in sync? If your picture has the top and bottom halves of the screen reversed and it will not stop rolling, change your sync polarity on the monitor. (Positive to negative (see tech tips section).

NOTES: “oy

B) Now how’s your picture? © Is it centered?

  • Is it too bright or dim? ® Is it in focus? Check your monitor manual for these adjustments. If your screen looks “off”, then your new game transformation may have been in vain. So let's take the time to make the monitor look great. C) Is the picture upside-down? Refer to your monitor manual - switch two horizontal yoke wires and then switch two vertical wires. (Pull the pins in the connector on the monitor P.C.B. to switch them.) or check Dip Switch Tables

SESS ET SEAL TES RD LTE RTH TEP EST EEE

Page 12

Control Panel Assembly

  • Remove the buttons, joysticks and wire harness and put them aside for now. Do not remove the original panel overlay until the new holes have been drilled.
  • Mark positions on the panel for the new holes. ROMSTAR supplies a clear 1/8” thick piece of plexiglass with every new game package to cover the control panel. We feel that your new game | investment is well worth protecting. . .and the control panel is the first place to show wear and tear. You will need to cut this piece to size. Use the control panel as a template. Use a razor knife to score the plexiglass deeply. Then use a Pair of pliers to break away the extra plexiglass.
  • Now drill the holes in your panel that you have marked off for the buttons, Joystick and bolts. ‘ Hint: For best results, use a chassis or sheet metal punch for button holes.
  • _ Drillthe same holes on your plexiglass panel protector. Once again use your panel as a template. Hint: To avoid chipping while you are drilling the holes, place the plexiglass securely on a soft wood surface and use a plexiglass drill bit and hole cutter.
  • The holes are now all cut. Smooth them out on your panel and plexiglass with a fine toothed file.
  • Remove the original graphics overlay from the panel. Clean up the panel and install your ROMSTAR graphics. Make It Easier: Peel the top half of the protective backing off of your graphics. Start from the center and smooth out your overlay. Make sure you have about an inch extra coming off the top. Vo bubbles please. Now peel off the bottom half and do the same as you did for the top.
  • Adhere the instruction and function labels.
  • Install the Plex Control Cover over your completed new game panel.
Note: Be sure to bolt the plexiglass securely to the panel.
  • Mount the joystick and the buttons to the panel and wire them up. (Use the existing Panel wiring if possible)

Marquee Installation

Using the original marquee as a template, Center your new game marquee graphics and score the new marquee deeply to fit the cabinet. Break off the excess with pliers.

Note: when cutting marquee to size, check to make sure that you are cutting as ~ little of the necessary art as possible (name, manufacturer, etc.)

Be sure the light behind the marquee works. Everything should always work on anew game. : Take your time ... Don’t forget this is going to be a new game.

Page 13

Side Graphic Installation

is Pa

3:

4. Be sure sides of game are clean'and free of old adhesive, dust, etc. Mark position of decal with eraseable pen or pencil (centered on upper half of cabinet). 2 Peel off top 1/4 of decal backing and apply to cabinet with a smoothing motion (use a soft rag). Continue peeling off backing and smoothing. Remove any small bubbles with a pin or razor blade (pop them!)

Finishing Touches

ig Check the game inside and out for any imperfections. Secure any loose wiring or fastening hardware. Make sure the coin door is tight and the coin mechs are well adjusted. A game is no good to anybody if you can’t get a coin into it. Once again go over every step of this mew game transformation in your mind. Be sure everything is correct and to your liking. Power up the game. A. Check all the coin switches. (Does the coin meter work?) B. Play your new game . ¢ Are all the player controls working? ¢ Are the game sounds present?

  • Is the volume level proper? ° Are the dip switches set properly? Well, that’s about it. Good Luck.

-*

ARKANOID CONTROL ASSEMBLY

Page 14

Star Tech Tips ‘ We are grateful to Star Tech Journaltm for allowing us to publish the following excerpts from their journal. &

  • Monitor Sync ~ : Ifyour monitor does not have dual polarity positions for sync, you may use one of the following methods to get your game going.

CURE 1: Install a simple one 1.C. Circuit on your logic board. This I.C. may be “piggy backed” on to another 7404 series chip for power by bending up all but the two power pins so that they are parallel to the top surface of the new I.C. and then connecting the power pins only to the existing chip. (See Fig. 1) Next connect the sync wires as shown in Fig. 2. (Note: Figure 2 shows a hookup for either composite or separate syncs.) HORIZONTAL SYNC INPUT FROM P.C.B. 5S Vcc SVODC [PIN 14) {OR COMPOSITE SYNC INPUT)

SOLDER TO HORIZONTAL SYNC OUTPUT TO MONITOR EXISTING CHIP. {OR COMPOSITE SYNC OUTPUT) VERTICAL SYNC INPUT FROM P.C.B

VERTICAL SYNC OUTPUT TO MONITOR

FIG. 2

BENT PINS | NEW LC. | J GND (PIN 7) EXISTING I.-C. vil ee FIG.1 SOLDER

CURE 2: Used for Wells-Gardner Video-Sync boards with positive sync connections only. (Vertical mount board 85x140B.

“Cut the traces on the solder side of the board between input pins 5 & 6to the unbanded (anode) ends of diodes X201 & X202. Add MPSAS56 transistor as follows: Collector to anode leads of diodes X201 & X202. Base to pins 5 & 6 of the video input connector. Emitter to cathode (banded) lead of zener diode ZD 201. Insert a IN4148 diode - cathode to the emitter of the MPSAS6 and anode to the base. (See Fig. 3) RED!

GREEN 2

4 BLUE 3

GND4 FIG.3 VERT. S

HORIZ. 6 MPSASG 0000 IN4148

2D201 a CUT TRACES & a

412 X20!

Page 15
  • Horizontal Tearing ? CAUSE: The negative sync signal of most logic sets are slightly different than the GO7-CBO monitor =~ negative sync inputs. The result of this mismatch is a horizontal “wave” or “curl”. CURE 1: On the monitor deflection board, replace C303 with a 10uf 25V radial lead capacitor with the Positive lead towards the collector of X305. (CAUTION: be sure to check this step as the original cap is not polarized.) Then replace C501 with the cap removed from the C303 location. CURE 2: Connect 1N4148 fast-switching diodes across both the positive and negative sync inputs to the monitor. (See Fig. 4) NOTE: Both diodes must be installed or you will not have vertical stability.

IN4148,

NEG: SYNC INPUT

FIG.4 BLUE GREEN RED *

IN4148

CURE 3: Join negative sync inputs J2 and J3 together with a jumper. Locate \W/102 and install a jumper from W102 to either J2 or J3.

CURE 3: For Wells-Gardner K4600 series monitors Replace C356 (4 7uf 25V) on the Horizontal vertical board (vertically mounted board nearest the flyback transformer) and center the horizontal hold pot. Turn L351 for the best horizontal stability and fine-tune with the horizontal width pot.

Ges)as. G52) OPTO-COUPLER PCB 1502 { OPTO-COUPLER PCB WW —-6 2] +5V-RED (Connector Side) oA 9 : ° ° NG #

hes ib [1] RIGHT-GREEN/BLUE 150Q mw—

4] LEFT-RED/YELLOW ‘ {3] GND-BLACK TO REMOVE KNOB & SHAFT ASSEMBLY - REMOVE NUT, SPROCKET, & E-CLIP FROM MAIN SHAFT,

NOTE : USE CONTROL ASSY. AS A TEMPLATE FOR MOUNTING HOLES ON CONTROL PANEL.

SELES PT TR a ay eT IT EE HL STE ee TSI SPRL PTE ETRY TET OAT

Page 16

-& Solder Side

Ground Parts Side

Ground

Ground Ground

+5VDC +5VDC

+5VDC +5VDC

N/A N/A +12VDC ee ht

+12VDC

» Post t t= Post"

Coin Counter 2 Coin Counter 1 Violet

Coin Lockout Coin Lockout Speaker (-} _ Speaker (+) Gray N/A Video. Green N/A’:

  • Video Red Red

Pink ~ Video SyNC tcompsnea) «

Service Switch “.. Video Blue Blue Video Ground . Black

Yellow Orange Tilt Switch

Coin 2 N/U ~ Blue

Coin 1 Tan Gray 2P Start

Green Blue N/U 7 & = IP Start Brown N/U Green

N/U N/U Blue

Violet 2P Left x} <}<}.c} a] | 2] 0] zf et efpate

IP Left Violet Yellow 2P Right IP Right Yellow Red 2P Fire Orange N/U IP Fire Red

N/U Orange N/A ~ NA N/A N/A N/A N/A Ground Ground

Ground Ground (2P - Table Kit Only Except 2P Start)