Centipede Cocktail TM-188 2nd Printing
Centipede (revision 4) (Atari, 1980) · Technical Manual · 64 pages · 37 sections · original scan
\) oy) N ®) Operation, Maintenance
NW fri LJr\
GAME SERIAL NUMBER LOCATION Your game’s serial number is stamped on a silver identification label, located on the outside of the game. The same number is also stamped on the chassis of the monitor, Regulator/Audio || PCB, the power supply, and Centipede™ Game PCB. Please mention this number whenever calling your distributor for service.
MONITOR
CENTIPEDE™, GAME PCB
GAME SERIAL NUMBER IDENTIFICATION TAG
REGULATORIAUDIO II PCB
POWER SUPPLY
™
oIN LA Q
Cockt. =
il
peration, Maintenance 4 and Service Manual
Complete with Illustrated Parts Lists
Copyright © 1981 by Atari,Inc. All rights reserved. No part of this publication may be reproduced by any mechanical, photographic, or electronic process, or in the form of a phonographic recording, nor may it be stored in a retrieval system, transmitted, or otherwise copied for public or private use, without permission from the publisher.
Published by: ATARI INC. 1265 Borregas Avenue P.O. Box 427 Sunnyvale, California 94086
Lithographed in the U.S.A. 9K
Notice Regarding Non-Atari Parts
WARNING
Use of non-Atari parts or modifications of your Atari game circuitry may adversely affect the safety of your game, and may cause injury to you and your players.
Atari, Inc.’s warranty (printed on the inside back cover of this manual) may be voided, if you do any of the following:
1.) you substitute non-Atari parts in your coin-operated game, or
2.) you modify or alter any circuits in your Atari game by using kits or parts not supplied by Atari.
Not only may the use of any non-Atari parts void your warranty, but any such alteration may also adversely affect the safety of your game, and may cause injury to you and your players.
Table of Contents
1 Set-Up Procedures A.
omm New Features................00005 ee Opening the Game Cabinet .
- Opening the Table Top .
- Access Panel.......
- Closing the Table Top Game Inspection . . Game Installation. .
- Voltage Plug Selection ....
- Interlock and Power On/Off Switches . Adjusting the Table Legs............ Self-Test Procedure .... Option Switch Settings .
- Bonus Play Feature. . wee
- Coin Mechanism Multipliers ............. ++. 10
- Examples of Game Price Settings Game Play
- Attract Mode
- Ready-to-Play Mode 2.00.0... cece cece eee cence ee
- PlayMode ..........
- High Score Initial Mode NORA WHOKWOWH4
2 Maintenance and Repair A B. Cleaning... 6... ete teen eee ees Fuse Replacement. The Control Panel ..........
- LED Start-Switch Replacement .
- Leaf Switch Replacement
- Mini-Trak Bail™ Maintenance and Repair Monitor Removal ..............-..- Printed-Circuit Board Removal ws
- Game PCB Removal ......- 0.00. e eee e nce eee tee eee neces
- Regulator/Audio Il PCB Removal ..........0.202 200 e cece eee ee 25 Speaker Replacement . Game Operation... 00... n eee ene
3 Illustrated Parts Lists Illustrations and parts lists begin on page ............. 0.0 eee eee 31
List of Illustrations
Figure 1 Overview of Game .... 6.6... eect eee tee teeta 2 Figure 2 Installation Requirements . 4 Figure 3 Voltage Plug Selection 4 Figure 4 Interlock and Power On/Off Switches ......... 2.2.0.0. c cence eee 5
Figure 5 Adjusting the Table Legs .......... 0... cece eee eee 6 Figure 6 Location of Self-Test Switch, Volume Control and Option Switches ... 7 Figure 7 Self-Test Procedure. . 8 Figure 8 Game Option Settings 1
Figure 9 Game Price Settings. ..... 6.0.0.0. e eee cette eee 12 Figure 10 Coin Counter Option Settings . Figure 11. Opening the Control Panel and Replacing witches . : : 20 Figure 12 Control Panel Wiring ........ 6.200. e eee eect tenets 21
Figure 13 Mini-Trak Ball™ Maintenance and Repair. -. 23 Figure 14 Monitor Removal ............... .. 24 Figure 15 Printed-Circuit Board Removal . rs) Figure 16 Speaker Replacement ............ 0.0. ese cee cence eee eee eee 26
Figure 17 Power Distribution .... 2.2.0... 6. cece cee eee eee ee 28 Figure 18 Signal Distribution ......... 06. e eee eeee 29
I/lustrated Parts Lists: Figure 19 | Cabinet-Mounted Assembiies Figure 20 Control Panel Assembly. . . Figure 21 Mini-Trak Ball Assembly ....... Figure 22 Centipede™ Game PCB Assembly ... om oe see eee. 40
Figure 23 Regulator/Audio lIlIPCBAssembly ..............-0 00 cece sees eee Figure 24 Power Supply Assembly for Color Raster-Scan Games . Figure 25 Double Coin Acceptor/Mount Assembly............-
Centipede™/Cocktai!
WEST and CENTRAL U.S.A. Parts for all Atari customers in the U.S.A. Game sales and service
Atari, Inc. California Customer Service Office 1105 N. Fair Oaks Avenue P. O. Box 427, Sunnyvale, CA 94086 Telex 17-1103 (Monday-Friday, 7:30-4:00 pm Pacific Time) roy From California, Alaska or Hawaii (408) 745-2900 From anywhere else in this area ‘toll-ree (800) 538-1611
EAST U.S.A. Game sales and service only
Atari, Inc. New Jersey Customer Service Office Cottontail Lane, Somerset, NJ 08873 Telex 37-9347 (Monday-Friday, 7:30-4:00 pm éastern time) age From New Jersey 2 (201) 469-5993
ae From anywhere eise in this area 2 toll-free (800) 526-3849
EUROPE Parts for all Atari customers in Western Europe. Game sales and service
Atari Ireland Limited European Customer Service Office TIPPERARY TOWN, Tipperary Town, Ireland (RELAND Telex 28165 (Monday-Friday, 9:00-6:00 pm GMT)
@ 06252155
vi
Set-Up Procedures
GTN XS
A. New Features
The Centipede™ game has four new features. Even if you are familiar with Atari games, you should
are: panels. The coin box is accessible only from the
@ = Mini-Trak Ball™. The widely used Trak Baill as- outside of the cabinet. sembly has been redesigned. The basis for this @ The newly-designed adjustable table legs procompact, simplified design is a two-part molded Plastic frame. Fewer parts in this control make servicing easier, and its very smooth action is designed for greater player accuracy. The circuitry has non-volatile memory for part of the high score table. This means that even if power is removed from the game, the three highvide improved cabinet stability while allowing two cocktail-table height settings: 27% and 30 inches. A third “upright” setting is 3934 inches high, and allows the game to be placed in locations with other upright games.
These new parts, as well as ail other major parts in the game, are illustrated in Figure 1. Throughout this manual, wherever one of these new parts is est scores will permanently stay in memory. To erase these scores follow the instructions in Figure 7, Self-Test Procedure. mentioned, you will see this symbol:
se SS
SECURITY BAR “>
‘COLOR MONITOR _—
SUPPORT ARM [_—— TABLETOP
CONTROL PANEL CENTIPEDE™ GAME PCB
Lock
POWER SUPPLY
UTILITY COIN SWITCH, POWER ON/OFF SWITCH SELF-TEST SWITCH, & VOLUME CONTROL
REGULATOR AUDIO Il PCB On apy ACCESS ——— PANEL ADJUSTABLE LEG
SPEAKER
COIN ACCEPTORS
COIN COUNTER
Figure 1 Overview of Game
aN
B. Opening the Game Cabinet
- Opening the Table Top @ To open the game cabinet, uniock and open the two locks at one end of the game, located immediately below the table top (see Figure 1). © Carefully lift the table top until the support arm locks into place. Do not jam the table top at the end of its upward swing.
- Access Panel
@ To open the access panel, lift up the steel security bar inside the cabinet wall. @ The access panel near the bottom of the cabinet will then come out. This small pane! was designed with a bar instead of the usual lock to reduce the number of keys required for this game.
- Closing the Table Top @ To close the cabinet, stand on the start-switch side of the cabinet and grasp the table top with your right hand. @ With your left hand, press the button at the middle of the support arm and push the support arm down towards the right. @ Gently lower the table top to the closed position. @ Lock the two latches on the left end of the cabinet, located just underneath the table top.
C. Game Inspection
This new game is ready to play upon removal trom the shipping carton. However, your careful inspection is needed to supply the final touch of quality control. Please follow these steps to help us insure that your new game was delivered to you in good condition.
- Examine the exterior of the game cabinet for dents, chips, or broken parts.
- Unlock the table top and open the access panel of the cabinet; inspect the interior of the game as follows: @ Check that all plug-in connectors (on the game harness) are firmly seated. Repiug any connectors found unplugged. Don’t force connectors together. The connectors are keyed so they only go on in the proper orientation. A reversed edge connector will damage a PCB and will void your warranty. @ Check that all plug-in integrated circuits on the game PCB are firmly seated in their sockets.
@ Note the location of the game’s serial number—it is printed on the special label on the outside of the game cabinet. Verify that the serial numbers also stamped on the Centipede™ Game PCB, Regulator/Audio || PCB, power supply, and monitor are all identical. A drawing of the serial-numbered components is on the inside front cover of this manual. Please mention this number whenever you call your distributor for service. ®@ Check ali major subassemblies such as the power supply, control panel and monitor for secure mounting.
(®
Centipede™/ Cocktail
D. Game Installation
Figure 2 Installation Requirements
Power 135 watts Temperature 0 to 38°C (32 to 100°F) Humidity Not over 95% relative Space Required 62% x 82V2 cm (2412 x 3212 in.) Game Height 65 to 101 cm (25% to 39% in.)
- Voltage Selection This power supply has four colored voltageselection plugs and operates on the line voltage of almost any country in the world.
Before plugging in your game, check your power supply. Make sure that the voltage selection plug on it is correct for your location’s line voltage. Check the wire color on the plug and see if it is correct per Figure 3.
- Interlock and Power On/Off Switches To minimize the hazard of electrical shock while working on the inside of the game cabinet, an interlock switch has been installed under the table top (see Figure 4). This switch removes all AC line power from the game circuitry when the table top is opened.
Check for proper operation of the interlock switch by performing the following steps: @ Be sure the table top is closed. @ Plug the AC line power cord into an AC outlet. @ Set the power on/off switch to the “on” position. Within 30 seconds the monitor should display a picture. @ Slowly open the table top. The monitor picture should disappear when the top is lifted approximately 2¥2 cm (1 inch). @ If the results of the preceding step are satisfactory, the interlock switch is operating properly. If the monitor doesn’t go off as described, check to see if the interlock switch is broken from its mounting or stuck in the “on” position.
Fuse cover must be in place during game operation.
voutace = SELECTION
Figure 3 Line Voltage Range Voltage Selection Plug Color 90-110 VAC (100) Violet 105-135 VAC (120) Yellow 200-240 VAC (220) Blue 220-260 VAC (240) Brown
Voltage Plug Selection
“sCocktail Centipede™
SWITCH COVER SAFETY
SWITCH fy INTERLOCK
POWER ON/OFF SWITCH @ &: & & £
Figure 4 Interlock and Power On/Off Switches
@ Remove or empty the coin box. Loose coins may slide out of the coin box and into the game cabinet. © Lay the table on its side. Place a support (the coin box, books or tool box) under the recessed side of the cabinet. @ Loosen the two Allen-head screws on each leg. Grasp the legs and slide them into the desired position. Then tighten the screws.
REMOVE COIN BOX. USE TWO SCREWS WHEN ATTACHING EACH TABLE LEG!
| ‘ SHIPPING POSITION (25% in.)
Figure 5 Adjusting the Table Legs
E. Adjusting the @ Table Legs
This cocktail-table game is designed for four adjustable heights—65, 70, 76 or 101 cm (2534, 27%, 30 or 39% inches). To adjust the table height, refer to Figure 5.
F. Self-Test Procedure
This game will test itself and provide data to demonstrate that the game’s circuitry and controls are operating properly. The data is provided on the monitor, light-emitting-diode start switches, and game speaker; no additional equipment is necessary. Part of the self-test procedure includes a display of the operator-selectable game options. Therefore, we suggest you run the self-test procedure anytime you need to change the game’s options. The locations of the self-test and option switches are shown in Figure 6. To run the self-test, follow the instructions outlined in Figure 7.
OPERATOR OPTION SWITCH (one of three sets)
CENTIPEDE™ GAME PCB a SELF-TEST SWITCH
VOLUME CONTROL (For volume increase, turn clockwise) COIN SWITCH
Figure 6 Location of Self-Test Switch,
Volume Control and Option Switches
Figure 7
Instruction Self-Test Procedure
Results if Test Passes (if results are not as indicated, see list of failures that follows)
- Begin: Set self-test switch to on position (see Figure 6).
- Mini-Trak Ball Test: Roll the Mini-Trak Ball controls in ail directions.
- Switch Test: One after another, activate and release all control-panel switches, the slam switch, and coin switches.*
- Audio I/O Chip Test: One after another, press and hold 2 of the control-panel ‘switches and at least one of the coin switches.
- Audio /0 Channel Test: Press 1-player start button four times.
- Background Color Test: Press 1-player start button at least 16 times.
- Object Color Test: Press 2-player start button at least 16 times.
- Moving Object Test: Watch the screen, and move the Mini-Trak Ball around. Place the moving object in an open area of the screen. Press fire button several times.
- Erasing the High Score Table (optional) The monitor displays the picture below. The game produces no sound at all. The two start-switch LEDs will stay on throughout self-test.
The centipede head moves around on the screen in directions corresponding to Mini-Trak Ball control.
As long as you activate (close) each switch, you'll hear a high beep.
Volume increases and pitch decreases with each additional switch that is activated.
You'll hear a high beep tor each press of the button.
Background color changes with each press of the 1-player stan button.
Objects on playfield change color.
Each press of the fire button changes the moving object to another moving object. At certain points in the series, the object will disappear. This is not a failure indication. The current three highest scores are held in permanent memory, even if the game is .N) unplugged. If you want to erase these scores, simultaneously press either fire and both start buttons. The 4 FF message in the upper left corner of the screen will then be displayed. The average game time data will also be erased, but still displayed on the screen.
- End: When satisfied with test, set self-test switch to off position.
- Activate coin switches by inserting at least one coin in each coin slot. You will not trip the coin counters as long as you stay in self-test.
NO. OF LIVES AT START OF GAME
ALL SWITCHES & TRAK-BALL INPUTS
BONUS COIN SETTING (means “for every 3 coins inserted, logic adds 1 more coin"). Blank it no bonus coins(s) given. See Fig. 8 for switch settings.
GAME DIFFICULTY SETTING ENTIRE CHARACTER SET
L, RCOIN MECH MULTIPLIERS:
TOTAL NO. OF CREDITS PLAYED
_OS PLAYS: AVG. GAME TIME 1559 GAME TIME x (accurate to +4 secs.)
Figure 7 Self-Test Procedure, continued
Results if Test Fails
- Begin: RAM FAILURE is indicated by one to 10 beeps. Note the number of beeps and determine which RAM may be bad. To restart the test, press the reset pushbutton on the game PCB, of set the selftest switch to off, then again to the on position. Possible Bad Number of Beeps Given RAM Chip Location H2 F2 K7
L7 ©ONS GROW «= a
10 NS Any bad RAM must be replaced before the computer can check the other RAMs, as well as continue with the self-test.
ROM/PAOM FAILURE is indicated by two groups of numbers in the upper left corner of the screen. The number at the far left indicates the location of the failing PROM/ROM(s). Identify the bad ROM/PROM with the table below. If the screen displays “garage," or the logic produces strange audio or randomly activates the coin counters, the chip at location J1 is probably bad. Ignore the hexadecimal numbers just to the right of the chiplocation number. Failing ROMPROM Displayed Number Chip Location 0O oO1 1 Et 2 FIH1
- or “garbage” wt 4* E5* 5 BICIDS *If you replace or erase this ROM, the number 4 FF will be dispiayed throughout the self-test. The next time you enter self-test, the 4 disappears after a game is played. Otherwise the self-test will continue to display the numbers 4 FF.
- Mini-Trak Ball Test: The character doesn't move in same direction as ball, jumps rather than moves smoothly, or doesn’t move at all. One of the Coupler PCBs in either Mini-Trak Ball control may be bad, harness wires or connector may be loose, Mini-Trak Ball reading circuitry on Game PCB may be bad, or Mini-Trak Ball bearings may need oiling.
- Switch Test: Sound is constantly on, even though you are not activating any switch. Or, no beep is given for any switch, or LED is dark. indicates a bad switch, loose harness wires, bad LED-driving circuitry, volume turned ail the way down, or loose connector.
- Audio /O Chip Test. No increase in volume or decrease in pitch indicates bad custom audio I/O chip at location B/C/D3.
- Audio I/O Channel Test: ‘On one out of the four activations, no audio is produced. Indicates one channel is bad in the custom /O audio chip at location B/C/D3 (reptace entire chip),
- Background Color Test: Background doesn't change color, or doesn’t display all 16 colors. Indicates bad color RAM chip. (RAM failure would have been indicated earlier with from 3 through 10 beeps.)
- Object Color Test: Objects don’t change color, or don't display all 16 colors. RAM failure.
- Moving Object Test: Object doesn’t change to another object. ROM/RAM failure. “SS
G. Option Switch Settings
- Bonus Play Feature Centipede™ offers a bonus play for certain combinations of coins inserted. This bonus feature is operator-selectable, meaning you may choose to offer it or not.
With your game set at 25¢ per play, players who deposit four successive quarters or a $1.00 coin, then press the start button, can receive a bonus coin. Therefore, players can receive 5 plays for $1.00.
This bonus feature encourages players to insert more money than just the minimum 25¢ you could require for one game. Various other bonuses are also available (see Figure 9).
- Coin Mechanism Multipliers The Atari coin acceptor mount for this game is available with about a dozen different mechanisms. You may have both mechanisms accept the same or different denominations. Regardless of the type of mechanism you install, you must correctly set the mech “multipliers” on the game PCB. The multipliers determine how much each mechanism wil! be worth to the game’s logic.
The basic unit of measurement is 25¢, which equals a multiplier of x1. Therefore, if you have a 25¢/$1 coin acceptors, you will probably want to set the left and right option-switch multipliers at xx 4.
You can set these multipliers with toggles 3 thru 5 on the Centipede PCB switch assembly at location N8. For exact settings of these toggles, refer to Figure 9.
- Examples of Game
Price Settings
Figure 9 explains the options, giving twelve examples of the most common U.S. situations. The toggles mentioned are ali in the switch at location N8; they only relate to game price, coin mechanism multipliers, and bonus “coins” for inserting multiple quarters or the $1.00 coin. You should set the toggles relating to other functions as you see fit, although Figures 8, 9, and 10 provide “$” symbols indicating Atari's recommendations.
Figure 8 Game Option Settings To change toggle positions on the switch assemblies, you need not remove the game PCB. The switches, usually colored blue, are easily accessible when the Centipede Game PCB is mounted in place. When changing the options, verity proper results on the monitor display by performing the self-test. Note that changing an option on any of the following eight toggles will not cause an immediate change on the monitor screen during the attract mode.
Toggle Settings of 8-Toggle Switch on Centipede Game PCB (CENTER switch assembly when PCB is in game) 8 7 6 5 4 3 2 (at N9)
1 Option
On On Off Off
On On On Off
Off On
Off Off
On On On Off
On Off
On Off On English $
Off German
On French Off Spanish 2 lives per game Slives pergame $ 4 lives per game 5 lives per game Bonus life granted at every: 10,000 points 12,000 points $ 15,000 points 20,000 points Hard game difficulty* Easy game difficulty* $ 1-credit minimum $ 2-credit minimum
$ Manufacturer's suggested settings *Refer to Section F. Game Play, in this manual for information on game difficulty. For pricing for “credits,” see Figure 9. Changing toggles 3-7 erases the high score table.
a
Figure 9 Game Price Settings The white block below contains Atari's suggested settings. All Circled numbers refer to game pricing labels you should use numbers 1 thru 8 are toggle settings on the 8-toggle switch at lo- with each situation fiabels are on the following page). Use the cation N8, on the Centipede™ game PCB (the LEFT switch label no. 6 (indicated with) only if you set toggle 8 at PCB switch assembly). assembly NQ of off.
50¢ PER CREDIT:
Bonus Bonus $.75 = 2 plays No bonus $1.00 $1.00 = 3 plays
25c/25¢ Mechanisms
25¢/$1.00 Mechanisms
25¢ PER CREDIT:
Bonus Bonus
No bonus $.50 = 3 plays $1.00 = 5 plays
| 8 | 7 | 6 | 5 | e | |
| 250/25¢ | ® | Off | Off | Off | Off |
Mechanisms
| 4 | 3 | 2 | 1 |
| Off | Off | On |
25¢/$1.00 Mechanisms
Figure 9 Game Price Settings, continued For your information, we have defined below the switch set- To achieve bonus plays, all coins must be inserted before presstings for those options relating to game price, coin mechanism ing the start button. The labet no. 6 shown below shauld be used. multipliers, and bonus play. This information is useful in case you only if you set toggle 8 at PCB switch assembly Ng to off. need to temporarily set the Centipede™ game on free play, or if you have German coin mechanisms in your door.
Toggle Settings of 8-Toggle Switch on Centipede PCB (at N8—LEFT switch when PCB is in game)
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | Option |
On
On
On
Off
Off
| On | On | Free play | |
| On | Off | 1 coin* for 2 credits | |
| Off | On | 1 coin* for 1 credit | $ |
| Oft | Off | 2 coins* for 1 credit | |
| On | on | Right coin mech x 1 | $ |
| On | Off | Right coin mech x 4 | |
| Off | On | Right coin mech x 5 | |
| Off | Off | Right coin mech x 6 | |
| On | Left coinmech x 1 | $ |
Off Left coin mech x 2
| On | On | No bonus coins | $ |
| On | Off | For every 2 coins* inserted, game logic adds 1 more |
coin*
| Off | On | For every 4 coins* inserted, game logic adds 1 more |
coin*
| Off | Off | For every 4 coins* inserted, game logic adds 2 more |
coins*
| On | On | For every 5 coins* inserted, game logic adds 1 more |
coin*
| On | otf | For every 3 coins* inserted, game logic adds 1 more |
coin*
*in the U.S., a “coin” is defined as 25%, In Germany a “coin” is 1 DM. $ Manufacturer's suggested settings To achieve bonus plays, alt coins must be inserted before pressne @@ 2 coins | @@@ 3 coins ing start button. 008 @ 4 coins Game Pricing Labels: oe 6 e@ 2 coins = 1 play Js @@ 2 coins =1 play A $1 coin =3 plays (Susan B. Anthony coi
e o @ 1 coin = 1 play
| A | in | = | A |
AS @ 1 coin = 1 play ame 2 play minimum
(2 coins = 2 plays)
(For operator use—write in the appropriate phrase. Use @ permanent-ink water-resistant marker) AO @@ 2 coins = 1 play ATARI
@ 000 4 coins = 3 plays
Figure 10 Coin Counter Option Settings
[These toggles determine which coin mechanisms activate which counters]
Toggle Settings of 4Toggle switch on Game PCB (N11)
| 4 | 3 | 2 | 1 |
Two coin acceptors in the coin door: Two coin acceptors and a pushbution utility coin switch in the game: Three coin acceptors in the coin door:
| On | On | Both acceptors activate all coin |
counters simultaneously.
| > | > | On | Off | Both acceptors activate 2 count- |
| gs | 3 | ers separately. |
a > 3 g 3 wat at co
| Off | On | Both acceptors activate all coin |
counters simultaneously.
| Off | Off | Both acceptors activate 2 count- |
ers separately. Do not use this setting.
Do not use this setting.
Utility coin switch will not activate a coin counter, if you do not hook it up. Both acceptors activate one coin counter. $
Utility coin switch will not activate a coin counter, if you do not hook it up. Left and right acceptors activate 2 coin counters All 3 are same denomination and they activate all coin counters simultaneously.
Left and center acceptor activate ‘one coin counter; right acceptor activates another coin counter.
Left acceptor activates one cain counter; center and right acceptor activate another coin counter. Not for any currently designed 3-mech coin door.
Left, center and right acceptors activate 3 coin counters separately.
separately. $$
$ Manufacturer's suggested settings for games with 1 counter $$ Manufacturer's suggested settings for games with 2 counters
H. Game Play
Atari's Centipede™ is a one- or two-player game with a color raster-scan monitor. The fast-moving action includes a variety of creatures dropping down from the top of the screen or flying in from its sides, most of them to attack the player. The piayer's shooter is represented on the screen by a somewhat humanoid head.
The player's goal is to shoot at and destroy as many of these creatures and mushrooms as possible for a high point score, before the player's lives are used up. Players can maneuver their Mini-Trak Ball™ control anywhere within approximately the bottom fifth of the screen. However, they must move around mushrooms, since these are fixed, not “transparent”, objects. A fire button shoots individual shots upwards, or fires a hail of shots if pressed constantly. (Only one shot appears on the screen at atime.) The game has five possible modes of operation: attract, ready-to-play, play, high score initial, and self-test. Self-test is a special mode for checking the game switches and computer functions. You may enter this mode at any time. When entered, all game credits are cancelled. Wait at least eight seconds after a game has been played before entering self-test or turning off the power. Otherwise, you may erase the high score table.
- Attract Mode The attract mode begins when power is applied to the game, after a play or high score initial mode, or after self-test. This mode is continuous and is only interrupted when a game is paid for and accepted or when in self-test. In this mode, the monitor displays two pictures simultaneously.
One of the pictures is operator-selectable for one of four languages. Placed in the center of the screen, the picture shows the high score table, game price, and the bonus-life achievement level. If the operator sets the Centipede game for free play, the game will not display a game price message.
The high score table shows the eight highest scores and their matching initials. If you erase the special “permanent” memory (see Figure 7, Self- Test Procedure), then this table will contain fictitious scores and initials. The table is redeveloped from subsequent games with scores of more than 12,102 points. Subsection 4, High Score Initial Mode, explains this table in more detail.
Operators may choose one- or two-credit minimums by selecting one of the option switch settings on the game PCB (see Figure 7, Game Option Settings).
\f the game is set for a 2-credit minimum, that message will be displayed on the screen. (No special message appears if Centipede is set to the opposite setting, namely 1-credit minimum.)
QZ a.” The other picture surrounds the high score table, game price and bonus-life achievement ievel messages. That picture displays a typical game-play sequence, with a field of colorful mushrooms through which a centipede crawls. The spiders bounce in from the sides of the screen, and fleas occasionally drop down from the top. In addition, scorpions will cross the screen at almost any point.
In this mode, the action exactly duplicates a typicai game played by a moderately skilled player: the player's shooter moves freely within the limits of motion, shooting at spiders, centipedes, fleas and scorpions. Periodically the player is “destroyed” when a flea, spider or centipede head or body collides with the player's shooter.
All the colors on the screen change with each wave. A new wave occurs when the player shoots all centipede parts remaining on the screen. At this point, a new centipede starts snaking its way down from the top of the screen.
The attract mode differs from real game play in that no head figures are shown at the top of the screen to represent the number of lives remaining, no sounds are produced, no scores are incremented, and none of the player controls work.
At any time when the game is powered up, if the slam switch is closed, you will hear a special alarm sound. This sound alerts location personnel that the game has been abused.
- Ready-to-Play Mode This mode begins when sufficient coins are accepted for a one- or two-player game. It ends when the 1-player start or 2-player start pushbutton is pressed. When this mode begins, the message CRE- DITS __ is displayed in the middle of the screen. The pictures are otherwise the same as those shown in the attract mode.
If you select the two-credit minimum and a player inserts enough money for only one credit, the message 2 CREDITS MINIMUM flashes on the screen until enough coins for the second credit are inserted.
In addition, CREDITS 0% is displayed if you have selected the option of two coins per credit, and the player has inserted only one coin. A “credit” is defined as the cost for each player to play one game. In other words, two credits will pay for:
@ one player playing two games, or @ two players playing one game.
- Play Mode The play mode begins when any flashing start pushbutton is pressed. The mode ends when the player's last life is lost.
If a two-player game is being played on a cocktailtable game, the screen image will invert 180 degrees with each new life. This places the shooter immediately in front of each player.
A player's shooter is enabled at the beginning of the play mode, and the audio starts. The appropriate LED start switch will then stay lighted until the end of the game. At this point it will flash if any credit remains. The game begins with a playfield of randomly placed mushrooms. A centipede starts snaking its way across from the center top of the screen. The centipede changes direction when it runs into a mushroom or either the left or right boundaries of the playfield. When a centipede is shot, it breaks into two smaller ones, each with a head. Also the part of the centipede that was shot leaves a mushroom in its place on the screen. When any centipedes reach the bottom of the screen, they start back up, but remain within the area of the player's shooter (the bottom fifth of the screen).
When a large centipede (that hasn't been shot yet) reaches the bottom, it releases its tail, and this part changes into a new head. Also to provide player challenge, if a centipede is still alive when it reaches the bottom, new heads will enter the screen almost at the bottom of the sides. More of these heads will appear as time progresses.
The randomly moving spiders also appear in the first wave. The spiders can destroy a player, as well as any mushrooms they move over. This eliminates many mushroom targets for a player.
The player's shooter is moved by rotating the Mini-Trak Ball™ control. The shooter can be moved in all directions, but only within the bottom fifth of the screen. Pressing the fire button causes the shooter to fire shots upward, either singly or in rapid-fire mode, if held down constantly.
Mushrooms count 1 point when shot, and a player must fire four shots into a mushroom before it is destroyed and disappears. Centipede body parts count 10 points each, and the elusive heads (represented with small eyes on them) are worth 100 points each. Spiders are worth 300, 600 or 900 points, depending on how close they are to the player when shot.
A bombardment of fleas starts in the second In the hard setting, the spider moves slowly only wave; as the fleas descend, they leave a trail of new for the first 1,000 points, and then speeds up. It also mushrooms behind them. changes direction more often throughout the game. In either setting, the spider always moves at a In the second wave, the fleas appear when a cer- 45-degree angle or straight up and down. tain number of mushrooms remains at the bottom of the screen. This number increases as the game progresses, meaning fleas appear more often later on in the game. Another operator option is the number of lives per game, ranging from 2 to 5 (see Figure 8 for switch settings). This number is displayed as small shooters at the top of the screen. The number is decreased by one each time a player is destroyed. The number is increased by one each time the player scores multiples of 10, 12, 15 or 20 thousand points, depending on the operator selection. Fleas have a value of 200 points when shot, and players must hit them twice to destroy them (the first shot just speeds them up).
The scorpion enters from either side starting in . ae the fourth wave; it moves at a relatively slow speed. 4. High Score Initial Mode Later it increases its Speed. When shot, a Srorall. If a player’s score exceeds the minimum on the counts 1000 points—the highest-value target of all. high score initial list, he or she may put up to three As it travels across the soreen, it “poisons” the initials on this list at the end of the game. At the be-
- ; ginning of this mode, the characters A _____ appear mushrooms that it moves over and changes their nthe screen. The logic will also display the mescolors. These mushrooms cause any centipedes T RI that would collide with them to head straight toward sages GREAT SCORE and ENTER YOUR INITIALS. the bottom of the screen, rather than continue snak- Players enter initials one character at a time, ing around. Players can stop a poisoned centipede choosing from the characters A thru Z and a blank by shooting its head. space. Pressing the fire button selects the letter, and rolling the Mini-Trak Ball™ control changes the In addition, these poisoned mushrooms as well letters on the screen. as any partially shot mushrooms add 5 points to the player's score at the end of each life when the screen is resetting. After the fire button is pressed the third time, the initials and score are transferred to the table. This table contains eight scores and appears during the If the players are very skilled and earn at least attract and ready-to-play mode. 60,000 points, two things happen to increase player All but the highest three scores are erased whenchallenge: the fleas descend at a faster speed and ever you enter the self-test, or press the RESET butthe spiders restrict their movement to a smaller area ton on the game PCB, or iurn off the power. The rea” the bottom of the screen. setting replaces the lowest five scores with fictii initials.
An important new feature of this game is the oper- Housiseores ancl Initisls SS
ator option for easy/hard game difficulty. In the easy If you erase the special “permanent” memory, the game, the spider moves slowly up to a 5,000-point high score table is replaced with eight fictitious score, and then bounces at a higher speed. It also scores and initials. In other words, the table will alchanges direction less often throughout the game ways be displayed on the screen, possibly consisting than at the hard setting. of one or more realistic scores and players’ initials.
Ww
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
Maintenance and Kepair
All games require certain maintenance to keep them in good working order. Clean, properly maintained games will attract players and earn more profits.
The most important maintenance item is running the self-test every time you collect money from the coin box. Just looking at a game will not tell you if Mini-Trak Ball™ controls, light-emitting-diode switches or leaf switches are broken, or if LEDs have burned out. The self-test will inform you of any of these possible problems.
Second, you should regularly clean the outside of the game and the coin mechanisms. In addition, you will need to regularly clean the leaf switch contacts SEES and lubricate the Mini-Trak Bal! control: for details Ui see this chapter. N
LEAF SWITCH
TURN NUT TO RE- MOVE WHITE BUTTON
Figure 11
A. Cleaning
The exterior of the game cabinet and the metal, glass, and plastic surfaces may be cleaned with any non-abrasive household cleaner. If desired, special coin machine cleaners that leave no residue can be obtained from your distributor.
The large table top is made of tempered glass and should be scratch-resistant. If cleaned without abrasive substances, you should hardly ever have to replace it.
B. Fuse Keplacement
This game contains six fuses—all on the power supply assembly (not including the monitor fuses). Replace fuses only with the same type as listed in Figure 24 of this manual. See the Matsushita monitor manual, TM-153, for the monitor fuse data. COMMON CONTACT \ a Vt NORMALLY OPEN EX ——~__ (N10) CONTACT
NORMALLY CLOSED (N.C) CONTACT LIGHT-EMITTING-DIODE (L.E.D.) CONTACTS
To Remove LED Switch: Remove all wires from the faulty switch. @ Turn the switch counterclockwise while holding the black cone-shaped bushing on the outside of the contro! panel. @ Install a new switch using the reverse procedure. Reconnect the harness wires.
Opening the Control Panel and Replacing Switches
C. The Control Panel
Prior to repairing or replacing any switch or the Mini-Trak Ball™ on the control panel, unplug the game. Next, open the game top as described in Chapter 1, Section B, Opening the Game Cabinet.
Finally, remove the two sets of button-head screws and lock washers at the top edge of the control panel. Once this hardware is removed, the control panel will tilt toward you.
After servicing the start switches or any components on the control panels, be sure you reconnect the harness wires to the proper termination points, as shown in Figure 12. Otherwise the controls may not work properly—causing frustration in players and possibly reduced income from the game. y.)
- LED Start-Switch Replacement The light-emitting diode (LED) switches near the control panel have a very low failure rate. In case a switch should ever be suspect, first test it per the description that follows. To replace the switch, refer to Figure 11.
@ Remove the wires from the suspected switch. @ Set multimeter to ohms scale. Set ohms scale to Rx1, then zero the meter. @ Connect multimeter leads to appropriate LED switch contacts (see Figure 11 for designation of switch contacts and meter lead placement). @ Check coniacts (push and release the switch button) for closed and open continuity. @ If the contacts do not operate sharply or always remain closed or open, then replace the LED switch as outlined in the figure.
- Leaf Switch Replacement
Adjust switches for a narrow gap. When a switch button is depressed, the resulting wiping action of the contacts provides a self-cleaning feature.
All five of these leaf switches operate on 5 volts at a very low current. Therefore, pitting of these switches would be extremely rare. Probably the only reason that pitting would occur is that the game is in a very high-humidity location.
Don’t burnish the switches. Burnishing them removes their plating, thus increasing the corrosion of the contacts. The best method of cleaning the switch contacts is to wipe them with a non-abrasive surface. A business card works very well.
RED
GREY STRIPE
WHT. WITH BROWN STRIPE VERT.-MOTION PCB: GREEN RED, BLACK & YELLOW WIRES. BLACK
IRE SWITCH:
HORIZ..MOTION PCB: BLUE, RED, BLACK & VIOLET WIRES. UP EITHER WAY WHT. WITH ———— +
WHT, WITH BLACK STRIPE
2 WIRES MAY BE HOOKED 2-PLAYER START SWITCH
1-PLAYER START SWITCH
WHT. WITH. RED STRIPE RED
Figure 12 Control Panel Wiring
To replace any switch, remove both of its screws with a Phillips-head screwdriver—see Figure 11.
lf the white button itself needs to be replaced, turn the stamped nut with a wrench in a counterclockwise direction, as seen from the inside of the control panel. The white ring on the outside of the control panel should not spin, due to its design.
- Mini-Trak Ball™ Maintenance
an and Repair
The Mini-Trak Ball™ control requires lubrication of its bearingsapproximately every 6,000 credits or every 3 months. To lubricate or repair the control, remove the control from the control panel and disassemble it as illustrated in Figure 13.
Use only 2 drops of 3-in-One® oil in each of six ball bearings of the Mini-Trak Ball control.
For further instructions on how to replace the ball, either coupler PCB or either encoding wheel, see Figure 13.
Disassemble in the order indicated. (Circled numbers match the steps described below.)
Ball Replacement
- First remove the entire Mini-Trak Ball assembly from the control panel as shown in Figure 11. Now locate the six “twin-lead” thread-forming screws in the black frames (plastic pieces); remove these six screws.
- Lift off the top frame; remove and replace the ball.
Coupler PCB and Encoding Wheel Replacement
- Lift the PCB out of its slot. Carefully unplug the red connector on the coupler PCB. 4, To replace eitehr encoding wheel, remove the PCB from its slot. Remove the socket-head machine ‘screw, flat washer, and split lock washer that secure the encoding wheel. Remove the wheel. When replacing the coupler PCB, be certain that the black metal encoding wheel has not been bent or damaged. It should turn freely between the two halves of the red photosensor device.
LUBRICATE HERE (6 PLACES)
Figure 13 Mini-Trak Ball™ Maintenance and Repair
Centipede™sCocktail
D. Monitor Kemoval
- Be sure the game is unplugged from its wall outlet! Unlock and open the table top.
- Lift up the “U”-shaped security bar, located along the inside wall of the cabinet. Remove the bar entirely from the cabinet. Remove the access panel from the side of the game.
- Locate the 6-pin monitor and 3-pin power connectors underneath the monitor, just above the power-supply transformer. Unplug these connectors.
- Remove the four Phillips-head screws and flat washers (one set at each corner of the monitor screen). These attach the large monitor brackets to the cabinet.
- Carefully lift the monitor assembly up and out the cabinet.
Disassemble in the order indicated. (Circled numbers match the steps above.)
Figure 14 Monitor Removal
ow
CENTIPEDE™ GAME PCB
REGULATOR! AUDIO II PCB =
Figure 15 Printed-Circuit Board Removal
E. Printed-Circuit Board Kemoval
You may wish to remove the game printed-circuit board (PCB) or the Regulator/Audio II PCB for service or inspection. To do this, refer to Figure 15 and Proceed as follows:
- Game PCB Removal @ Unlock and open the table top. @ Remove the four beaded nylon tie-wraps from the top side of the game PCB. Then remove the two edge connectors. @ Locate the Phillips-head screws that extend through the PCB and into the two wood blocks near the top of the game. Remove and save these screws and the associated fiber washers. @ Remove the PCB from the game by carefully sliding it straight up out of the plastic PCB retainers. Be careful not to twist the board, as this may loosen connections or components. Replace or repair as required. @ After servicing it, reinstall the PCB, making sure that the edge connectors are properly plugged in. Note that the connectors are keyed to fit on only one way, So if they don’t slip on easily, don’t force them! A reversed connector will probably damage your game and wil! void the warranty. ®@ Check that the operation of the game is correct by performing the self-test. This is especially important with any game when you replace a PCB.
- Regulator/Audio II PCB Removal @ Unlock and open the table top. @ Remove the five plug-in connectors on the Regulator/Audio Il PCB. Note that all of these connectors are keyed for proper orientation. @ Remove the PCB from the inside wall of the Cabinet by pulling it up and out of the wood retainers.
PLUG-IN CONNECTORS
SPEAKER
Figure 16 Speaker Replacement
F. Speaker Keplacement
- Probably the only cause of speaker failure is an open voice coil or a ruptured cone, but both of these failures are highly unlikely.
Open the table top. Unplug both speaker-wire connectors. Use a very short-handled Phillips screwdriver to remove the two screws. For greater ease in reaching these screws, and to prevent slip- Ping and damaging the Regulator/Audio {| PCB, remove this PCB first.
G. Game Operation
With this manual you received two large sheets that contain the wiring and schematic diagrams for the Centipede™/Cocktail game. Sheet 1, Side A, includes a “table of contents” that shows the arrangement of these diagrams. They explain the functions of the circuits; the diagrams also define inputs and outputs. BR Atari’s Centipede™ is a microprocessor-controlled game. The microprocessor is mounted on the game PCB. The game PCB receives switch inputs from the control panels and coin acceptors. These inputs are processed by the game PCB and output to the monitor, Regulator/Audio I PCB, loudspeaker and control panel. Centipede™/Cocktait
The Regulator/Audio \| PCB performs two functions: 1) it regulates the +10 VDC from the power supply to +5 VDC, and 2) it amplifies the audio output from the game PCB. The +5 VDC from the Regulator/Audio (I PCB provides most logic power to the game PCB. The audio output from the Regulator/- Audio {I PCB directly drives the game speaker and is controlled by the volume control, mounted on a bracket inside the game cabinet.
The power supply is the source of all voltages in the game. These voltages are protected by three fuses (F3, F4 and F5) on the power supply chassis. The primary winding of the power-supply transformer is protected by the fuses F1 and F2 on the power-supply chassis.
Figure 17 illustrates the distribution of power in this game. Figure 18 illustrates the distribution of signals.
COLOR MONITOR
GAME PCB INTERLOCK SWITCHES ,
REGULATORIAUDIO Il PCB
FAN (OPTIONAL)
COIN ACCEPTORS ef
AC POWER CORD
POWER SUPPLY
POWER ON/OFF SWITCH
Figure 17 Power Distribution
Centipede™/Cockiail
COLOR MONITOR
GAME PCB
VOLUME CONTROL, SELF-TEST SWITCH & UTILITY COIN SWITCH
CONTROL PANEL A
(1 of 2)
AUuDio QUT
SPEAKER
REGULATORIAUDIO II PCB
COIN ACCEPTORS
Figure 18 Signal Distribution
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
Illustrated
Parts Lists
This chapter provides the necessary information for you to order replacement parts for the Centipede™/Cocktail game. Please note that, for simplicity, common hardware has been deleted from most of these parts lists. This includes screws, nuts, washers, bolts, etc.
The parts lists are arranged in alphanumeric order. For example, ail ‘‘A-” prefix numbers come first. Following these are numbers in sequence evaluated up to the hyphen, namely 00- through 99-, then 000598: through approximately 190000-.
When ordering parts from your distributor, give the part number, part name, applicable figure number of this manual, and seriai number of your game. This will help to avoid confusion and mistakes in your order. We hope the results will be less downtime and more profit from your game.
Atari Customer Service numbers are listed on page vi for your convenience.
Centipede™/Cocktait
037759-01 (Wood Table Top) 03585201 (Comer Brkt.)
037755.01 (Glass Table Top) 82-406 (Eyebolt)
02-305006 (Thltop. T-Moidi (roltop. ng) 034536-03
(Vibra. Damper)
037681.01 (Mon. Bezel)
035851-01 (Hinge) 178015-001 (labletop Support)
74-3003A, {Tubular Spacer)
A036189-01 (interl, Sw. w/Brt.) 007882.02 (Inter, Sw. Cvr.)
037686-01 (Cab, Grille)
A034841-08, A034863-08 or A035989.08 A005133-01 (Power Cord) (Fan—optionaly
037768-01 (Fan Grille)
78-3205 (Endcap) Ns < Gf (Brace)
02-305010 (Cab. T-Molding) 037791-01 (Secur. Bar) NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL; Reproduction forbidden without the spe Gilic written permission of Atari, Inc., Sunnyvale, CA. This, ‘drawing is only conditionally issued, and neither receipt nor possession thereof confers or transfers any right in, oF Ii: cense to use, the subject matter of the drawing or any de: Sign oF technical infermation shown thereon, "or any right to reproduce this drawing or any part thereot. Except Tor manulacture by vendors of Atari, Inc., and for manufacture under the corporation's written license, no right is granted te reproduce this drawing oF the subject matter thereo!. unless by written agreement with or written permission from the corporation
A037541-01 (Mon. Adapt. Hins.) 477001-130 (Metric Hex Nut)
92.054 (Electr. Mon.) “&
037792-01 (Mon, Mntg, Brkt.) “>
71-2110 (Lock)
71-3201 (Wsr. for Locks)
036774-01 (End-Pal. Grilie)
A037793-01 Pe Ne) (Cab. Base Assy)
A037292-01 (Leg Supp.)
78-3206 (Leg)
A037246-01 os (Leg Assy.)
Figure 19 Cabinet-Mounied Assemblies A037760-xx E
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific written permission of Atari Inc., Sunnyvale, CA. This drawing is only conditionally issued, and neither receipt nor Possession thereo! confers or transfers any right in, oF Ii cense to use, the subject matter of the drawing or any design or technical information shown thereon, ner any right to reproduce this drawing or any part thereof, Except for manufacture by vendors of Atari, Inc., and for manufacture under the corporation’s written license, no right is granted 10 reproduce this drawing or the subject matter thereof, un. less by written agreement with or written permission trom the corporation’ 035745-02 (PCB Retainer) 036764-01 Centipede Game PCB— (Hook-Type Cam) see Figure 22
A037945-01 (Main Harns.)
78-24012 (Tie Wrap),
75-07017 (PCB Spacer)
Control Panel Assy.— see Figure 20 Mini-Trak Ball— see Figure 21
035848-01 (Leg Backplate),
036773-01 (Grille) Power Supply— see Figure 24
61-162A (On/Off Sw.) 009992-01 (On/Off Sw. Cvr.) 006450-01 (On/Ott-Sw Plate)
037785-01 (Access Panel)
‘A036775-01 (Coin Box)
Figure 19 Schematics, Self-Test Labei & Manuals— see parts list on following page
78-6900401 ee AFoam zee)
035867-02 (Mon. Overlay)
Reg/Audio I! PCB— see Figure 23
036321-01 (Bracket) 69-001 {SellTest Sw.) 19-9032 (Vol. Ctrl.) 62.041 (Util Coin Sw! 75-9910NO {Stamped Nut)
48-004 (Speaker)
« 000869-01 (Spkr. Grille)
A002465-01 (Coin Counter)
A037760-xx E Ser 4 75-9910W0 « (Stamped Nut) 62.039 (LED Sw.) 033127-01 (Sw. Bushing) 03768201 (Mntg. Plate)
03775301 (Retng. Bracket)
Coin Accep/Mt. Assy.— see Figure 25
Cabinet-Mounted Assemblies
Centipede™/ Cocktail
Figure 19 Cabinet-Mounted Assemblies, continued Parts List
Part No. Description A002465-01 Coin Counter A005133-01 Cooling Fan {optiona/ equipment)
| A034841-08 | Strain-Relief Power Cord | (U.S.) |
| A034863-08 | Strain-Relief Power Cord | (Austria, Belgium, Chile, Denmark, Finland, France, Germany, Greece, |
Indonesia, Italy, Netherlands, Norway, Spain, Sweden, and Uruguay)
| A035989-08 | Strain-Relief Power Cord | (Australia and New Zealand) |
| A036189-01 | Interlock Switch with Bracket | (modified for safety) |
A036775-01 Coin Box Assembly (inciudes lock) A037246-01 Leg Assembly (includes leg, 2 adjustable feet and 2 endcaps)
| A037292-01 | Leg Support Assembly | (inc/udes 2 panel nuts and endcap) |
| A037541-01 | Monitor Adapter Harness | (for 14-inch Electrohome monitor only) |
A037793-01 Cabinet Base Assembly (inc/udes grilles, PCB retainers, leg backplate and hinges) me.) A037945-01 Main Harness Assembly The following six items are the technical information supplements to this game: DP-188-01 Centipede/Cocktail Schematic Drawings (Sheet 1) DP-188-02 Centipede/Cocktail Schematic Drawings (Sheet 2) ST-188 CentipedeiCocktail Label with Self-Test Procedure and Option Switch Settings TM-187 Service Manual for 14-Inch Electrohome Color Raster-Scan Monitor TM-188, Centipede/Cocktail Operation, Maintenance and Service Manual TM-192 Centipede Signature Analysis Guide
| 02-305006 | '¥-Inch Black Plastic T-Molding | (for table top) |
| 02-305010 | %-inch Black Plastic T-Molding | (for cabinet base) |
19-9032 50-Ohm, 12%2-Watt Wire-Wound Rheostat (for volume control) 48-004 5-Inch, 8-Ohm, 5-Watt, Round High-Fidelity Speaker 61-162A DPST Power On/Off Toggle Switch 62-039 Momentary-Contact SPDT Light-Emitting-Diode Switch with Red Cap 62-041 SPDT Momentary-Contact Pushbutton Utility Coin Switch with Black Cap 69-001 DPDT Self-Test Switch
| 71-2110 | Panel Cartridge Lock Mechanism | (for table top) |
71-3201 Anchor Washer for Table Top Locks 74-3003A #10 x %,-Inch-Long Aluminum Tubular Spacer (for table top support) 75-07017 Spacer for Mounting Printed Circuit Boards 75-9910NO #5,-11 Steel Stamped Nut (for utility coin switch) 75-9910W0 #°%,,-32 Steel Stamped Nut (for start switches)
| 78-24012 | 5-Inch Beaded Nylon Tie Wrap | (for game PCB edge connectors) |
78-3205 Square Black Endcap for Leg Assembly 78-3206 Cabinet-Leveling Leg 78-6900401 Vinyl Foam Single-Coated-Adhesive Tape, %4-Inch Wide x %.-Inch Thick (10% feet req'd.) 82-406 #14-20 x 2-Inch-Long Eyebolt, with 34-Inch Threads 92-054 14-Inch Color Raster-Scan Electrohome Monitor, mode! GO7-914 ms.) 000869-01 Speaker Grille 006450-01 On/Off Switch Mounting Plate 007882-02 Interlock Switch Cover 009992-01 On/Off Switch Cover 033127-01 Black Molded Switch Bushing 03453603 Foam Vibration Damper 035745-02 18-Inch-Long Plastic PCB Retainer 035848-01 Backplate for Attaching Leg [Continued on next page]
Figure 19 Cabinet-Mounted Assemblies, continued Parts List
Part No. Description 035851-01 Table Top Hinge 035852-01 Corner Bracket for Table Top 035867-02 Smoke-Color Acrylic Monitor Overlay 036321-01 Bracket for Volume Control, Self-Test and Utility Coin Switches 036764-01 Hook-Type Cam for Lock 036773-01 Grille in Cabinet Base 036774-01 Upper End-Panel Grille 037335-01 Leg Brace 037681-01 Cardboard Monitor Bezel 037682-01 Mounting Plate for Start Switches 037686-01 Slip-in Cabinet Grille (above coniro! panel) 037753-01 Coin Acceptor Retaining Bracket 037755-01 Tempered-Glass Table Top with Graphics 037759-01 Wood Table Top oniy 037768-01 Fan Grille (fan is optional—see part no. AQ05133-01) 037785-01 Access Panel 037791-01 Security Bar e 037792-01 Monitor Mounting Bracket 477001-130 Metric M5-0.8 Zinc-Plated Steel Hex Nut (for monitor mounting bracket) 178015-001 Hinged Table Top Support
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific written permission of Atari, Inc., Sunnyvale, CA. This crawing is only conditionally ‘ssued, and neither receipt nor possession thereof confers or transters aay right ip, OF lr Cense to use, the subject matter of the drawing or any design or technical information shown thereon, nor any right to reproduce this drawing or any part thereof. Except for manulaciure by vendors of Atari, inc. and for manufacture under the corporation's written license, no right is granted to reproduce this drawing or the subject matter thereof, unless by written agreement with or writen permission from the corporation.
A037763-01 (Ctrl. Pr.)
‘A037676-01 (Harness)
MiniTrak Ball™ Assy.— see Figure 21
178030-001 (Pushbtn, Assy.)
75-9910NO (Stamped Nut)
160013-001 (Leaf Sw Button Holder) 460012-001 (Leaf Sw. Only)
Figure 20 Control Panel Assembly A037764-01 A
Parts List
Part No. Description
A037676-01 Control-Panel Harness A037763-01 Control Panel with Graphics 75-9910NO #5,-11 Steel Stamped Nut
160013-001 Leaf Switch and Button Holder (leaf switch only is part no. 160012-001) 178030-001 Pushbutton Assembly
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
176010-106 —F (6 PLACES) 1 (Screw)
oN
036193-01 (Idler Shatt) le
035938-01 (Wheel)
75-0148 (@ PLACES) (Washer)
75-0448 (2 PLACES) (Waster)
72-8406 (2 PLACES) (Screw)
03619201 (Lower Frame)
034168-01 (Label—not shown for clarity) we NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the speerfic written permission of Atari, Inc., Sunnyvale, CA. This drawing isonly conditionally issued, and neither receipt nor Possession thereot confers or transfers any right iN, OF li cense to use, the subject matter of the drawing of any do- Sigh or technical information shown thereon, noz any right to reproduce this drawing or any part thereot. Except tor manufacture by vendors of Alan. Inc., and for manufacture under Ne corporation's written license, no righ is granted toreprocuce irs drawing or the Subjeci matter thereo!. un less by wntten agreement with or wilten permission from the corporation.
036191-01 (Upper Frame)
035936-01 (Bali)
035937-01 @) (Ball Bearing) 035931-01 (Rolter Shaft)
‘A036096-01 (Harness)
(PCB)
Mini-Trak Ball™ Assembly A036190-01
Figure 21 Mini-Trak Ball™ Assembly Parts List -.\)
Part No. Description A035220-01 Coupler PCB Assembly A036096-01 Harness Assembly 72-8406 #4-40 x %-Inch Hex Socket-Head Cap Alloy Steel Machine Screw 75-0148 #4 Flat Plain SAE-Standard Zinc-Plated Steel Washer 75-044S, #4 Zinc-Plated Steel Split Lock Washer 034168-01 Label with Lubrication Instructions
| 035931-01 | Roller Shaft | (2 per assembly) |
035936-01 Mini-Trak Ball™
| 035937-01 | Ball Bearing | (6 per assembly) |
035938-01 Etched Encoding Wheel 036191-01 Upper Black Plastic Frame 036192-01 Lower Black Plastic Frame
| 036193-01 | idler Shaft | (7 per assembly) |
176010-106 #8 x %-Inch Cross-Recessed Pan-Head Thread-Forming Twin-Lead Zinc-Plated Steel Screw
Pe asl <= Hoel | pain FES*; Get FSF) Gees
353 a | (esr [ess neater earerd [sane 3034 keer} : as Ea Gs ae as Fad aE waza} (ast rs) ce (amt Gm Gam f3
$hat u 4 mas SS ae oil
a
G Figure 22 Centipede™ Game PCB Assembly A037241-01
Figure 22 Centipede™ Game PCB Assembly Parts List
Part No. Description (Reference Designations and Locations in Bold)
C012294-01 Audio 1/0 N-Channel MOS/LSI Custom Chip (C3) 24-250106 10 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (C83) 24-250107 100 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (C52, 78) 24-500105 1 uf Aluminum Electrolytic Fixed Axial-Lead 50V Capacitor (C79-82, 84, 86, 90, 94-97, 100, 105-108)
24-500106 10 uf Aluminum Electrolytic Fixed Axial-Lead 50V Capacitor (C85) 29-088 .1 uf Ceramic-Disc 25V Radial-Lead Capacitor (C3, 5-37, 40-51, 54-64, 66-77, 87, 88) 31-1N914 75V Type-1N914 Switching Diode (CR1, 2) 31-1N4001 75V Type-1N4001 Switching Diode (CR4, 5) 33-2N3906 Type-2N3906 PNP Switching and Amplifying Transistor (Q3) 34-2N3904 Type-2N3904 NPN Silicon Transistor (Q1, 2, 4, 5) 34-2N6044 Type-2N6044 Darlington NPN Transistor (Q6-8) 37-LM324 Type-LM324 Integrated Circuit (K10)
37-4584B Type-4584B CMOS Integrated Circuit (E/F10, E/F11) 37-555 Type-555 Timer Integrated Circuit (A11) 37-74LS00 Type-74LS00 Integrated Circuit (L8) 37-74LS04 Type-74LS04 Integrated Circuit (K3)
37-74LS08 Type-74LS08 Integrated Circuit (B7, K4) 37-74LS10 Type-74LS10 Integrated Circuit (L3, K2) 37-74LS20 Type-74LS20 Integrated Circuit (A7) 37-74LS32 Type-74LS32 Integrated Circuit (A4, C5, E3, F3, J3)
37-74LS42 Type-74LS42 Integrated Circuit (H3) 37-74LS74 Type-74LS74 Integrated Circuit (D4, D11, M3) 37-74LS83 Type-74LS83 Integrated Circuit (F6, H6) 37-74LS86 Type-74LS86 Integrated Circuit (E7) 37-74LS90 Type-74LS90 Integrated Circuit (L2) 37-74LS139 Type-74LS139 Integrated Circuit (C4, J2) 37-74LS153 Type-74LS153 Integrated Circuit (C7, E8, K6, L6, M6, N6, P6) 37-74LS157 Type-74LS157 Integrated Circuit (D7, D8, D/E11, F8, H8, J8, K8, P5)
37-74LS163A Type-74LS163A Integrated Circuit (A5, B5, M2, N2, N3, P2, P3) 37-74LS166 Type-74LS166 Integrated Circuit (H9, J9) 37-74LS174 Type-74LS174 Integrated Circuit (C6, D6, E6, J4) 37-74LS175 Type-74LS175 Integrated Circuit (A8, E4, M4, N4)
37-74LS191 Type-74LS191 Integrated Circuit (B11, C11) 37-74LS244 Type-74LS244 Integrated Circuit (B1, C1, H5) 37-74LS245 Type-74LS245 Integrated Circuit (E2) 37-74LS257 Type-74LS257 Integrated Circuit (D9, D/E10, K9, L9, P7, M8, M9)
37-74LS259 Type-74LS259 Integrated Circuit (M10) 37-74LS273 Type-74LS273 Integrated Circuit (B4, J6) 37-74LS373 Type-74LS373 Integrated Circuit (J5) 37-74LS374 Type-74LS374 Integrated Circuit (H4)
37-74S04 Type-74S04 Integrated Circuit (N1) 37-74S74 Type-74S74 Integrated Circuit (E9, F9) 37-7407 Type-7407 Integrated Circuit (A9, A/B10) 37-7815 + 15V Voltage Regulator (VR2)
37-7915 -15V Voltage Regulator (VR1) 38-MV5053 Type-MV5053 Light-Emitting Diode (CR3) [Continued on next page]
Figure 22 Centipede™ PCB Assembly, continued Parts List
Part No. Description (Reference Designations and Locations in Bold) 41-3003 100 uH, + 5%, Hot-Molded Plastic Fixed R.F. Choke (L1-3) 62-001 SPST Momentary Pushbutton Switch (Reset) 66-114P1T 4-Station, Singie-Throw, Dual-Inline-Package Bit Switch (N11) 66-118P1T 8-Station, Single-Throw, Dual-Inline-Package Bit Switch (N8, NS) 79-42C016 16-Contact Medium-insertion-Force Integrated Circuit Socket (P4) 79-42622 22-Contact Medium-Insertion-Force Iniegrated Circuit Socket (E5) 79-42C24 24-Contact Medium-Insertion-Force Integrated Circuit Socket (F7, H/J7, D1, E1, F/H1, J1) 79-42C40 40-Contact Medium-Insertion-Force Integrated Circuit Socket (C2, C3) 81-4302 Nylon Snap-In Fastener 90-102 12.096 MHz + .005%, Crystal (Y¥1) Acceptabie substitute is part no. 144000-001. 90-6013 Microprocessor 6502A (C2) 90-7005 Random-Access Memory (C8) 90-7018 Random-Access Memory (K5, K7, L5, L7, M5, M7, N5, N7) 90-7033 Random-Access Memory (F2, H2) 020670-01 Test Point 110000-102 1K Ohm, +5%, %4W Resistor (R9-11, 13-16, 23-28, 31-38, 55-60, 67, 68, 77, 79, 80, 87-89, 94, 95, 99, 104, 109, 114-123, 134, 136-141, 148, 149) 110000-103 10K Ohm, +5%, %W Resistor (R1, 2, 6-8, 12, 17-22, 29, 30, 39-54, 70, 71, 83-86, 130-133, 147, 150) 110000-104 110K Ohm, +5%, %W Resistor (R81, 82, 105, 106) 110000-105 100 MegOhm, +5%, 14W Resistor (R5) 110000-152 1.5K Ohm, +5%, %4W Resistor (R108) 110000-221 220 Ohm, +5%, %4W Resistor (R3, 62, 64, 66, 72, 74-76, 78, 135) 110000-222 2.2K Ohm, +5%, %4W Resistor (R107) 410000-331 330 Ohm, +5%, %W Resistor (R61, 63, 65, 73) 110000-332, 3.3K Ohm, +5%, %W Resistor (R69, 143-146, 151-154) 110000-471 470 Ohm, +5%, %W Resistor (R90-93, 96-98, 100, 110-113, 124-129, 142) 110000-560 56 Ohm, +5%, YW Resistor (R101, 102) 119000-563 56K Ohm, +5%, %4W Resistor (R4) 122002-102 .001 uf Ceramic-Disc 50V Radial-Lead Capacitor (C4) 122004-224 .22 uf Ceramic-Disc 25V Radial-Lead Capacitor (C65) 122005-103 .01 uf Ceramic-Disc 25V Radial-Lead Capacitor (C53) 128002-101 100 pf Radial-Lead Epoxy-Dipped 100V Mica Capacitor (C1) 128002-102 1000 pf Radial-Lead Epoxy-Dipped 100V Mica Capacitor (C98, 99) 128002-221 220 pf Radial-Lead Epoxy-Dipped 100V Mica Capacitor (C38, 39) 128002-390, 39 pf Radial-Lead Epoxy-Dipped 100V Mica Capacitor (C2) 136001-201 or -211 136001-202 or -212
136001-303 or -307 136001-304 or -308 136001-305 or -309 136001-306 or -310
136001-213 137161-001
137169-001 137170-001 Read-Only Memory (F7) Read-Only Memory (H/J7) Read-Only Memory (D1) Read-Only Memory (E1) Read-Only Memory (F/H1) Read-Only Memory (J1)
Programmable Read-Only Memory (P4) Type-ER2055 Integrated Circuit (E5) Note: If you replace this part, you must erase this ROM before locking up the game. See Figure 7, Self-Test Procedure, in this manual for instructions. Type-74LS107 Integrated Circuit (L4) Random-Access Memory {A6, B6) Acceptable substitute is part no. 90-7035.
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
Centipede™/Cocktaid
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without tne spe- Gific written permission of Atari, inc., Sunnyvale, CA. This, drawing is only conditionally issued, and neither receipt nor possession thereof confers or transfers any right in, oF li- Bense to use, the subject matter of the drawing or any de ‘sign or technical information shown thereon, nor any right to reproduce this drawing or any part thereot. Except for manufacture by vendors of Atari, Inc., and for manufacture under the corporation's written licer'se, no right to reproduce this drawing is granted or the subject matter thereot unless by written agreement with or written permission from the corparation. R33 Sci f—a)
| ” | «eet 5,7 | | | ||
| c| | cRo | 4 | Q | |
| A | & | a | =| | 9 |
| a= See | tee | é |
ao ac
| C20 | oe | 0 | es |
a C19 a
| —j | 3300, | fF |
35V
| 4 | So | + | |
| ds | _ | C23 | cai |
L___3a¥__ feet} 4e22+ as {ane} Pez 22 24, | QoQ ' = — Nel.) Q9 ees} 2612 7905
8 =o
| Oo | 35 | 4R24,10,7 | oO |
Zz er
TIP 32 TOA2Z002 A TDA2002A Slag NaSae 05 io 2 R54 ia ASS C3] coma = RB x|s0 Bs
| ceG@e | {o}" | paris |
ristow
RO 1/2W
Q 8
Figure 23 Regulator/Audio Il PCB Assembly A035435-02 E
Centipede™/ Cocktail
Figure 23 Regulator/Audio Il PCB Assembly Parts List
Part No, Description (Reference Designations and Locations in Bold) 12-52P7 2.7 Ohm, +5%, 1W Resistor (R5)
| 16-54P0 | 4 Ohm, +5%, 5W Wirewound Resistor | (R25) |
19-100P1015 1 Ohm, +3%, 7W Wirewound Resistor (R24) 19-315102 1K Ohm Vertical PCB-Mounting Cermet Trimpot (R8)
| 24-250108 | 1000 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor | (C13) |
| 24-250477 | 470 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor | (C1, 4, 12) |
24-350226 22 uf Aluminum Electrolytic Fixed Axial-Lead 35V Capacitor (C24, 31)
| 24-350338 | 3300 uf Aluminum Electrolytic Fixed Axial-Lead 35V Capacitor | (C9, 10, 18, 19) |
| 24-500105, | 1 uf Aluminum Electrolytic Fixed Axial-Lead 50V Capacitor | (C22, 23) |
29-088 .1 uf Ceramic-Disc 25V Radial-Lead Capacitor (C3, 11, 20, 21) 31-1N4002 100V 1-Amp. Silicon Rectifier Type 1N4002 Diode (CR1, 4) 31-1N5401 100V 3-Amp. Silicon Rectifier Type 1N5401 Diode (CRS5-8)
| 33-TIP32 | PNP Power Transistor, Type TIP32 | (Q2) |
| 34-2N3055, | NPN Silicon Transistor, Type 2N3055 | (Q3) |
| 37-LM305 | 5V Linear Voltage Regulator | (Q1) |
| 37-7812 | +12V Voltage Regulator, Type 7812 | (Q8) |
| 37-7905 | -5V Voltage Regulator, Type 7905 | (Q9) |
72-1608C #6-32 x ‘2-Inch Cross-Recessed Pan-Head Corrosion-Resistant Steel Machine Screw 726606S #6 x %-Inch Pan-Head Thread-Forming Cross-Recessed Type-AB Zinc-Plated-Steel Screw (Q8)
| 75-F60405 | #6-32 x ¥-Inch Binder-Head Nylon Screw | (Q5, 7) |
75-99516 #6-32 Nut/Washer Assembly
| 78-16008 | Thermally Conductive Compound | (Q3) |
| 78-16014 | Thermally Conductive Silicon Insulator | (Q2, 9) |
| 79-58306 | 6-Position Connector Receptacle | (J6, 9) |
| 79-58308 | 9-Position Connector Receptacle | (J7) |
| 79-58346, | 12-Position Connector Receptacle | (J10) |
| 79-58354 | 4-Position Connector Receptacle | (J8) |
020670-01 Test Point 034531-01 Heat Sink 100015-103, .01 uf Ceramic-Disc 25V Radial-Lead Capacitor (C5, C14) 110000-010 1 Ohm, +5%, %4W Resistor (R10, 19)
| 110000-100 | 10 Ohm, +5%, YW Resistor | (R11, 20, 29, 30) |
110000-101 100 Ohm, +5%, YW Resistor (R4, 12, 22)
| 110000-102 | 1K Ohm, +5%, %W Resistor | (R27, 28) |
| 110000-103 | 10K Ohm, +5%, YW Resistor | (R13, 14) |
| 110000-271 | 270 Ohm, +5%, %4W Resistor | (R1) |
110000-330 33 Ohm, +5%, %4W Resistor (R3)
| 110000-392 | 3.9K Ohm, +5%, YW Resistor | (R6) |
| 110000-562 | 5.6K Ohm, +5%, %W Resistor | (R32, 33) |
| 110000-752 | 7.5K Ohm, +5%, %W Resistor | (R7) |
| 110001-221 | 220 Ohm, +5%, %2W Resistor | (R9, 21) |
| 116000-220 | 22 Ohm, +5°%, 10W Wirewound Resistor | (R31) |
| 122002-102 | .001 uf Ceramic-Disc Minimum 25V Radial-Lead Capacitor | (C2, 7, 16) |
| 122004-224 | .22 uf Ceramic-Disc 25V Capacitor | (C6, 8, 15, 17) |
| 137151-002 | Type TDA2002A 8W Linear Audio Amplifier Integrated Circuit | (Q5, 7) |
79-4411001 (Fuse Post) 034544-01 46-2017002 (Fuse Block Cvr.) 46-2013002 (Fuse) (Fuse)
034482-02 (Chassis)
A034623-03, (Power Supply Harn. Assy.) A035674-01 (Volt. Plug Assy.) 79-3206 (Fuse Block)
78-2708 (Bushing)
78-70501SC: TOP VIEW (Bracket) NOTICE TO ALL PERSONS RECEIVING THIS DRAWING e' CONFIDENTIAL: Reproduction forbidden without the spe- 29.053 cific written permission cf Atari, Inc., Sunnyvale, CA This drawing is ony conditionally isstied, and neither recelpt nor (Elec. Cap possession thereof confers or transfers any right in, oF li Gense to use, the subject matter of the drawing or any de- Sign or technical information shown thereon, "or any right to recroduce this drawing or any part thereo!. Except for manufacture by vendors Of Atari, Inc., and for manufacture Under the corporation's written license, no right is granted 442001-001 10 reproduce this drawing or the subjeci matter thereof, unless by written agreement with or written permission from (Transformer Only) ‘the corporation BOTTOM VIEW A006555-01 (Rect. PCB Assy.)
4034630-01 7915021001 (RFI Filter) (Block)
A034629-01 (AC Harness Assy}
Figure 24 Power Supply Assembly for Color Raster-Scan Games A036099-01 A
Centipede™ Cocktail
Figure 24 Power Supply Assembly for Color Raster-Scan Games Parts List
Part No. Description A006555-01 Rectifier Printed Circuit Board Assembly A036098-01 Transformer and Harness Assembly (includes shielded power transformer) (Tt) A034629-01 AC Harness Assembly A034630-01 RFI Filter Assembly (FL1) A035674-01 Voltage Plug Assembly (set of four plugs) 29-053 26,000 uf 15V Electrolytic Capacitor (C1) 46-2013002 3-Amp. 250V 3AG Stow-Biow Glass Cartridge-Type Fuse (F4-F6) 46-2017002 7-Amp. 250V 3AG Slow-Blow Glass Cartridge-Type Fuse (F1-F3) 78-2708 Nylon Type 6/6 Hole Bushing with %-Inch Inside Diameter x °%,-Inch Outside Diameter x Ya-lnch Thick 78-70501SC_ 2-Inch-Diameter Capacitor Mounting Bracket 79-15021004 2-Circuit Single-Row Terminal Block 79-3206 5-Position 3AG Fuse Block with %4-Inch Quick-Disconnect Terminals 79-4411001 Panel-Mounting Non-Indicating 3AG Cartridge-Type Fuse Post 034482-02 Metal Power-Supply Chassis (acceptable substitute is Atari part no. 034482-01) 03454401 Fuse Block Cover 142001-001 Shielded Power Transformer Only (with isolation windings)
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING 99-15038 CONFIDENTIAL: Reproduction forbidden without tye spe- 99-15001 thru 99-15017 _(gezel for Button) cific written permission of Atari, Inc., Sunnyvale, CA. This (Ret. Button) ‘drawing is only conditionally issued, and neither receint nor possession thereo! confere or transfers any vight in, oF Cense to use, the subject matter of the drawing oF any desian or techrical information shown hereon, néranyvght to reproduce this drawing or any part thereo!, Except Tor manufacture by vendors of Atari, Ie, and for manufacture Under the corporation's written licenge, no nght's granted to reproduce this drawing or the subject matter thereat, un less by writen agreement with or written permission from the corporation.
—— 10.15052
(Spring for Button) 99-15051 (Lamp Holder)
LY
~~ 99-15026 2 beeeea
Lé (Lever) 99-15056 (Coin intet) (Screw tor Bezel)
\ Oe 99-15039 \ (Coin Inlet) (Bezel tor Cover)
99-15036 (Cover)
99-15055, 99-15041 (Retng. Screw) (Lockout Coil)
99-15053 (Lockt. Coil Spring) 99-15054 (Pivot for Lever) 99-15027 (Coin Ret. Box)
+ 99-15028 (Coin Ret. Box)
99-15056 djust (Sw. Adjuster) (Screw for Bezel)
99-15060 _— (Sw. Cover)
‘A036597-01 (Harness—not shown for clarity) 99-15029 (Bracket) eosose——~ ES (Switch)
Figure 25 Double Coin Acceptor/Mount Assembly A036693-01 thru -20 c
Figure 25
A036693-01 — US. 25¢/25¢ Coin Door A036693-02 1.S. 50¢/50¢ Coin Door ‘A036693-03 — British 10 P/10 P Coin Door ‘A036693-04 — British 10 P/50 P Coin Door ‘A036693-05 — British 20 P/50 P Coin Door A036693-06 — German 1 DM/1t DM Coin Door ‘A036693-07 — German 2 DM/1 DM Coin Door Double Coin Acceptor/Mount Assembly Parts List
‘A036693-08 — German 2 DM/5 DM Coin Door A036693-09 — German 1 DM/5 DM Coin Door A036693-10 — Belgian 5 Fr/S Fr Coin Door A036693-11 — French 1 Frit Fr Coin Door ‘A036693-12 — French 2 Frit Fr Coin Door A036693-13 — Swedish 1 Kr/1 Kr Coin Door ‘A036693-14 — Hong Kong $1/$1 Coin Door A036693-15 — Canadian 25¢/25¢ Coin Door ‘A036693-16 — Spanish 25 Pts/25 Pts Coin Door A036693-17 — Swiss 1 Frit Fr Coin Door ‘A036693-18 — Italian 100 L/100 L Coin Door A036693-19 — Japanese 100Y/100Y Coin Door ‘A036693-20 — Australian 20¢/20¢ Coin Door
Part No. Description A036597-01 Double Coin Acceptor Harness Assy. 99-15001 Coin Return Button with U.S. 25¢ Price Plate 99-15002 Coin Return Button with U.S. $1 Price Plate 99-15003 Coin Return Button with German 1 DM Price Plate 99-15004 Coin Return Button with German 2 DM Price Plate 99-15005 Coin Return Button with German 5 DM Price Plate 99-15006 Coin Return Button with Belgian 5 Fr Price Plate 99-15007 Coin Return Button with French 1 Fr Price Plate 99-15008 Coin Return Button with Japanese 100 Yen Price Plate 99-15009 Coin Return Button with British 10 Pence Price Plate 99-15010 Coin Return Button with Australian 20¢ Price Plate 99-15011 Coin Return Button with Italian 100 Lire Price Plate 99-15012 Coin Return Button with U.S. 50¢ (2 x 25¢) Price Plate 99-15013 Coin Return Button with British 20 Pence Price Plate 99-15014 Coin Return Button with British 50 Pence Price Plate 99-15015, Coin Return Button with French 2 Franc Price Plate 99-15016 Coin Return Button with Swiss 1 Franc Price Plate 99-15017 Coin Return Button with Hong Kong $1 Price Plate 99-15025 Left Half of Coin Inlet 99-15026 Right Half of Coin Inlet 99-15027 Side Plate of Coin Return Box 99-15028 Base Plate of Coin Return Box 99-15029 Switch Bracket 99-15030 Flap for Lockout Coil (U.S. 25¢) 99-15036 Coin Return Cover 99-15037 Switch Adjuster 99-15038 Bezel for Coin Return Button 99-15039 Bezel for Coin Return Cover 99-15040 Coin Return Lever 99-15041 Lockout Coil 99-15042 Coin Switch for U.S. 25¢ 99-15051 Lamp Holder 99-15052 Spring for Coin Return Button 99-15053. Spring for Lockout Coil 99-15054 Pivot for Coin Return Lever 99-15055 Retaining Screw 99-15056 Screw for Both Bezels 99-15060 Switch Cover
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
YOUR COMMENTS, PLEASE! Centipede" Cocktail 2nd printing
Your comments will assist Atari in improving the usefuiness of our publications. They are an important part of preparing for revisions of manuals and parts catalogs. No postage stamp is necessary if mailed in the U.S.A.
If you have any technical questions about certain Atari or Kee Games products, of are requesting additional publications, we will immediately forward your note to the appropriate person.
Page: Comments:
Fill in if you wish a reply:
Name.
Firm © Distributor
Address Cl Operator
City State Zip Ci Other_ Area Code Phone
First fold
No Postage Necessary if mailed in the United States
BUSINESS REPLY MAIL
FIRST CLASS PERMIT NO. 1004 SUNNYVALE, CA
POSTAGE WILL BE PAID BY ADDRESSEE
Atari, Inc. Attn.: Field Service/Coin-Op Division P. O. Box 427 Sunnyvale, California 94086
Second foid
re a
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
En Aen RES RN REN BE BE RES Bea a
Warranty
Seller warrants that its printed circuit boards and parts thereon are free from defects in material and workmanship under normal use and service for a period of ninety (90) days from date of shipment. Seller warrants that its television monitors (in games supplied with monitors) are free from defects in material and workmanship under normal use and service for a period of thirty
- days from date of shipment. None of the Seller's other products or parts thereof are warranted.
If the products described in this manual fail to conform to this warranty, Sellers’ sole liability shall be, at its option, to repair, replace, or credit Buyer's account for such products which are returned to Seller during said warranty period, provided:
- Seller is prompily notified in writing upon discovery by Buyer that said products are defective;
- Such products are returned prepaid to Sellers’ plant; and
- Seller's examination of said products discloses to Seller's satisfaction that such alleged defects existed and were not caused by accident, misuse, neglect, alteration, improper repair, installation or improper testing.
In no event shall Seller be liable for loss of profits, loss of use, incidental or consequential damages.
Except for any express warranty set forth in a written contract between Seller and Buyer which contract supersedes the terms of this order, this warranty is expressed in lieu of all other warranties expressed or implied, including the implied warranties of merchantability and fitness for a particular purpose, and of all other obligations or liabilities on the Seller's part, and it neither assumes nor authorizes any other person to assume for the Seller any other liabilities in connection with the sale of products under this order.
The use of any non-Atari parts may void your warranty, according to the terms of the warranty. The use of any non-Atari parts may also adversely affect the safety of your game and cause injury to yourself and others. Be very cautious in using non-Atari-supplied components with our games, in order to insure your safety.
Atari distributors are independent, being privately owned and operated. In their judgment they may sell parts or accessories other than Atari parts or accessories. Atari cannot be responsible for the quality, suitability or safety of any non-Atari part or any modification including labor which is performed by such distributor.
This document is and contains contidential trade secret information of Atari, Inc.
This document is loaned under confidential custody for the sole purpose of operation, maintenance or repair of Atari equipment and may not be used by or disclosed to any person for any other purpose whatever, and remains the property of Atari, Inc.
Neither it nor the information it contains may be reproduced, used, or disclosed to persons not having a need to know consistent with the purpose of the loan, without written consent of Atari, Inc.
AN ATARI
ATARI INC 1265 BORREGAS AVENUE P.O. BOX 427 SUNNYVALE, CALIFORNIA 94086 408/745-2000 * TELEX 35-7488