CATHODE RAY TOMES

Silent Scope EX Kit (400875 GEA13)

Silent Scope EX (ver EAC 1.20) (Konami, 2001) · Manual · 42 pages · 38 sections · original scan

Page 1

ORIGINAL VIDEO GAME —” _ OPERATOR'S MANUAL KONAMI

@Failure to operate the machine correctly could result in malfunction or accidents,so please read this manual carefully before commencing operation. Be sure to operate the machine as described in this manual. @Keep this manual carefully so as to be ready for use when necessary.

Page 2

About this product

Thank you for purchasing this KONAMI product. This manual explains how to operate your game machine correctly and safely.

This manual covers the following models: This kit can replace the following machine models. Never use it for any other types of machines.

“SILENT SCOPE: 830251

*SILENT SCOPE 2 DARK SILHOUETTE: 931251

*The specifications of this product are subject to change without notice for reasons such as improving the performance.

The contents of this game, its main devices and design are protected under each law concerning patent, copyright and other intellectual properties.

*Unauthorized reproduction of this document or any of its contents is strictly forbidden.

© 2001 KONAMI ALL RIGHTS RESERVED.

Portions of this product©1996-1999 3DIx Interactive, Inc.

Page 3

Contents

Bl Precautions for USC csssessssssssscscccssersesescesssstesesssseeessossssnusseesseeereesereseeeescsssnssees 2 Bi Locations of warning and other safety labels Specifications . HIKit set-up outline and flowchart

1 Setting up in the machine 1-1 Replacing the PCB unit. 1-2 Setting the memory card 1-3 Setting the PCB unit... 1-4 Replacing the title panel 1-5 Applying the decorative labels

2 Game settings 2-1 Checking the game start up 2-2 Setting and adjustment of game mode 2-3 Mode descriptions 3 How to play 4 Troubleshooting 5 Annex 5-1 Exploded view .. 5-2 Wiring diagram.

Page 4

i Precautions for use

The following safety precautions are given throughout this manual. They must be strictly followed to protect those who install, use or maintain this product as well as to prevent other bodily injury and property damage.

Be sure to read the following

*The following suggestions show the degree of danger and damage caused when the product is used improperly with the suggestions disregarded.

A WARNING

Indicates a situation where disregarding the suggestions could result in death or serious injury.

Indicates a situation where disregarding the suggestions could result in injury or product damage. P

*The following graphic suggestions describe the types of precautions to be followed.

Indicates a matter of which care should be taken.

Indicates a matter which is forbidden.

Indicates a matter which should be performed without fail.

Definitions of qualified in-shop maintenance persons and industry specialist who handle this product. ein this instruction manual, some procedures require a qualified in-shop maintenance person or industry specialist. For such instructions, a qualified person must take care of the jobs. -Otherwise an electric shock, machine trouble, or a serious accident may result. ‘Replacing the machine parts, inspecting and maintaining the machines, and troubleshooting must be assigned only to a qualified in-shop maintenance person or industry specialist. This booklet gives instructions that hazardous jobs in particular must be handied by an industry specialist. Qualified in-shop maintenance persons and industry specialist are defined as follows. Qualified in-shop maintenance persons -A qualified in-shop maintenance person must have experience in maintaining amusement machines, money changers and the like. Under the supervision of an amusement machines shop owner or manager, he or She routinely assembles, installs, inspects and maintains the amusement machines, or rprecee their component units and consumable parts, in the amusement machines workshop and/or shop. Jobs handled by qualified in-shop maintenance persons Assembling, installing, inspecting and maintaining amusement machines and money changers, and replacing their component units and consumable parts. Industry specialist . . .

  • An industry specialist must be engaged in designing, manufacturing, inspecting and servicing amusement machines. or he or she must have an education in electrical, electronic and mechanical engineering, and routinely maintain and repair amusement machines. Jobs handled by industry specialist .
  • Assembling and installing amusement machines and money changers, and repairing and adjusting their electrical, electronic and mechanical component parts.
Page 5

Precautions for use

A WARNING

*Be sure to carefully read this manual before setting up this product. Improper handling may cause machine trouble or accident. Ask a qualified industry specialist to set up this product or contact your nearest dealer. (You will be charged.) _

Handle this product with enough care when setting it up in the machine. Improper handling may cause machine trouble or accident. *The parts inside the machine become hot. Do not touch any internal parts until the machine cools down. *This product and some in-machine parts have projections. Be very careful not to injure yourself with such sharp points.

Do not place containers holding chemicals or water on or near the game machine. *Electrical shock or damage could be caused by water or foreign matter entering the inside of the machine.

Before setting up this product, be sure to turn OFF the machine’s main power switch and unplug the power cord from the receptacle. *Olherwise, machine trouble or electric shock may result.

¢There is high voltage inside the machine. Only a qualified industry specialist should Open the machine's side door and back door. With the door open, be very careful not to touch the monitor and its nearby parts. *Otherwise, an accident or electric shock may result.

Before installing the PCB unit, clean up the inside of the machine with a vacuum cleaner or the like. Dust deposits on the electrical parts may invite an electric shock or fire.

When setting up this product, connect the connectors tightly. *Otherwise, machine trouble or fire may result.

¢Strictly refrain trom disassembly and repair of parts which are not indicated in this manual, as well as settings and remodelling. *Otherise, a fire, malfunction or trouble may result. In case of any trouble, ask your nearest dealer for repairs and other services. KONAM} will not assume any responsibility for damage to the product attributable to disassembly and repair of parts which are not indicated in this manual, as well as settings and remodeling. OA @

Page 6

Precautions for use

A CAUTION

*This product is specifically designed for the following machine. Never use it for any other types of machines. Other types of machines may get in trouble. *SILENT SCOPE (830251) Dark Silhouette SILENT SCOPE 2 (931251)

“Before detaching and attaching the memory card and PCB unit, put on a grounding band as an anti-static measure. Do not handle these parts on a carpet or rug. *Static electricity may damage the electronic parts in the PCB unit.

While the PCB unit is running, do not pull out or push in the memory card. *Otherwise, the game may fail to play.

Make settings of the DIP switches on the PCB unit only as specified in this manual. *Otherwise, the program may fail to install itself or the game may fail to play. OOO ©

elf any connectors or cables of the machine or the PCB unit is found damaged, immediately stop using the machine and contact your nearest dealer for replacing the damaged part. Continued use of the damaged part may cause fire or electric shock.

PRECAUTION IN HANDLING

*When setting up or handling this product, follow the procedures and instructions set forth in this manual and perform such work safely. *Do not remove labels of “WARNING”, “CAUTION”, etc. attached to the product. *Do not set up or handle this product under conditions equivalent to the condition of “WARNING” or “CAUTION” specified in this manual. lf a new owner is to have this product as a result of transfer, etc., be sure to give this manual to the new owner.

Page 7

Mi Locations of warning and other safety labels

Mi Types of warning and other safety labels

| (peer Do not place any objects her

‘They may be knocked off byte Gun,

*To avold injuries, please keep observers away from the guns white game is inpiay.

To avoid breaking the gun, please do not place any weight on it. Also, please do not touch the scope.

Page 8

i Specifications

Name Silent Scope EX CONVERSION KIT (Software and PCB unit) Kits supplies *struction MANUAL... eeseeeseseseeseeecesssenecetseseeenenseeees This manual PCB unit... *Relay PCB *Memory card .. Relay wires ... *@screws(M3x8L) *Spacer.... *Title panel .. Decorative label

(— Preparations for set-up *@ screwdriver (#2) L *Grounding band (required to remove static electricity in handling the devices)

*lf any part is defective or not found, contact your nearest dealer. *The specifications of this product are subject to change without notice for reasons such as improving the performance.

Page 9

MEMO

Page 10

li Kit set-up outline and flowchart

WKit set-up outline = = ee ee ee eee

a

i g

2 & 3 S

jelay wires

(Employ the currently used one.)

s ‘> Re

if = g “ / ; s* ya 5 vy 3 8

5288 y2 2g ce js sees ", Bese y 32 ra bee

19 (0 the number of

s & S <

mS Se,

Connect the connectors

‘of the machine.

Match the connector codes.

Back side] Connect the connectors referrin pins indicated in the figure.

Page 11

Kit set-up outline and flowchart

WiSet-up flowchart eee Be sure to take the following procedure to set up this product. 1 Replacing the PCB 1 Tum OFF the main power switch and unplug the power cord from the receptacle. wm See Page 10 (A qualified industry specialist must take care of the steps below.) oe i 2 Remove the machine's side door or back door. |» See Page 10 os 3 Remove the PCB unit. 1a) See Page 11

4 Set the PCB unit of this kit on the wooden board. |» See Page 13 2 Setting the memory card

1 Set the memory card in place. > See Page 15 + => 2 Make sure the DIP switches on the PCB unit are all at OFF. 1 See Page 15 3 Setting the PCB unit 1 Set the PCB unit of this kit and connect the wires to it. |» See Page 16 se 2 Fit the side door. ® See Page 16

4Replace the start button1m See Page 17
5.Replace the title panel1m See Pageld
6Apply the decorative labels™ See Page 20
7Turn ON the main power switch and make the game settings> See Page 21
Page 12

1 Installation

1-1 Replacing the PCB unit

main power switch and unplug the & 1 | Be sure to turn OFF the machine's AC power cord from the receptacle.

2 Wear a grounding band to prevent static electricity. Be sure to keep on the grounding band for the later procedures too. (The grounding band does not come with the kit.)

*Static electricity may damage the electronic parts in the PCB unit. fy

Clip this end onto a grounded ‘metalic part such as the coin input port and retum por.

3 | Detach the side door of the control unit (see at right).

*The side door may fall down when the screws are removed. Hold the side door with one hand and remove the screws. Your cabinet may not have a side door. If so, open the back door for access and skip to step 6.

MEMO Main power switch ‘AC power cord

Page 13

1 Installation

Disconnect all the connectors from the PCB unit as well as the connectors 1 , 2 and the networking cable. Once network cable is disconnected, remove the network cable and clamp filter completely.

Remove network cable and clamp filter completely. This version of the game software does not utilize network capability. MEMO

1:Speaker cable (Red, Black, Gray, White) 2:AMP Power cable (Orange, Black) MEMO

Remove the wing bolts. Hold the grip and gently draw out the wooden board with the PCB unit attached.

6 Pull out the connector, undo the clamp and disconnect the wires from the PCB unit. See at right.

*The speaker cable (red, black, gray, white) will be reconnected to the PCB unit of this kit. Keep them in a safe place until then. MEMO [engl] CNZH|

N31 | i CNS g Networking cable . Le CNS rex [ce unit ait | Do not disconnect these cables. Audio cable (red / white) (OPTION)| ]

Jo Lon2} [CN1}

Wooden board

(reused for setting up)

Clamp

Page 14

1 Installation

AMP power cable, as shown at 7 | Disconnect the audio cable and the right.

*The disconnected audio cable and AMP power cable (orange, black) will not be used. Keep them ina safe place. MEMO

PCB unit and take it off of the 8 | Remove the wood screws fixing the wooden board.

The four wood screws removed from the PCB unit will be reused to mount the PCB unit of this kit. Keep them in a safe place. ¢The PCB unit, the audio cable and the AMP power cable (orange, black) will not be used for this game. Keep them in a safe place. (Secure the audio cable and the AMP power cable with the clamp atop the PCB unit.) MEMO

Next install the PCB unit.

Page 15

1 Installation

HHow to install the PCB urit© == mw me oe aoe

memory card on top of the PCB unit 1 | Peel off the tape that attaches the of this kit.

«Instructions for installing the memory card canbe found on page 15.

MEMO

in Step 8 on page 12 ), fix the PCB 2 | Using the wood screws (removed unit in the position shown at right.

Place and fix the PCB unit in the specified direction as shown in the figure. Referring to this screw hole, place and fix the PCB unit of this kit. Existing PCB unit

UHL AL TTT UNL ‘ova iit ‘OSU AT

PCB unit of this kit Wooden board Top view

3 | Screw down the spacers of this kit into the PCB unit hand-iight.

*Do not use any tool to tighten up the spacers. The PCB unit may be damaged.

Page 16

1 Installation

Press the relay PCB of this kit evenly and firmly to the PCB unit. Fix this PCB with the accompanying screws of this kit.

Press on the connector of the relay PCB.

fo} af Relay PCB Do not push here. Press here. x45

Do not push on the other Connector end of the relay PCB.

Press on the connector of the relay PCB. MEMO

Relay wires 8 Pins 18 Pins Relay PCB

Screws (M3xX8L)

Hold the relay PCB evenly right and left.

Connect the relay wires of this kit to the PCB unit. Bundle the wires neatly. Place the accompanying clamp filter as close to the connectors as possible and secure the wires with the band.

codes.

Reconnect the connector (removed in Step 6 on page 11) of the speaker cable (red, black, gray, white) to the specified position on the relay PCB. Be careful to connect the wires, matching the number of pins and the ial |

RK PCB unit

Relay PCB eN

Speaker cable (red, black, grey, vie)

™~w™™ <

Page 17

1 Installation

1-2 Setting the memory card

MiHow to set up the memory Card == == = a me oe ou es oo ee

Insert the memory card of this kit in the upper slot (SLOT2) of the PCB unit. Be careful not to turn the card upside down.

*There are two memory card slots in the PCB unit. Be sure to insert the memory card, with the printed side up, deep into the upper slot (SLOT2). With the card in, make sure the eject button beside the slot is out.

  • Be sure to insert the memory card of this kit in the slot. MEMO

Make sure ail the DIP switches on the PCB unit are at the OFF position.

  • I Eject button PCB unit

PCB unit

BGAB x 1234 Allto be at OFF

Page 18

1 Installation

1-3 Setting the PCB unit

HiHow to set the PCB unit =

1 Take the wires, which are to be | faginewres connected to the PCB unit, out of ‘out of the contrat the control unit as shown at right. a Push the PCB unit deep into position.

2 Make sure the PCB unit is deep in a Place. Fix the wooden board with 7 7

  • ‘ake the wires the wing bolts. out of the controll

3 Reconnect the connectors (removed in Step 4 on page 11) to the relay PCB of the PCB unit.

Gy ‘Speaker cable

(red, black, grey, white)

CNS

CNG CNO

Relay PCB SS & Do not reconnect the AMP power cable (orange, black). (removed in Step 4 on page 17.) cnt

4 | Place the side door (removed in Step 3 on page 10) in position and fix it with the screws.

Page 19

1 Installation

1-4 Replacing the title panel

Hi How to replace the title pan) = = === sees eee eee ee

an

*|

‘| Be sure to turn OFF the machine’s main power switch and unplug the AC power cord from the receptacle.

Remove the screws off the top bracket that secures the title panel. See at right.

Pull up the title panel and replace it with the kit's one.

To fit the new title panel Make sure the new title panel fits into the bottom bracket. Then secure the top bracket with the screws. Top bracket f ‘Screws } Title pane

g hel,

Page 20

1 Installation

1-5 Applying the decorative labels

HApplying the decorative labels == == am me me ae me econ oe ee Just apply the decorative labels of this kit over the existing labels.

a 10.

*The label 5 is already attached on the rear Cover. *The labels 16 and 17 are already attached on the front cover.

1 | 400872Decal, Player Instructions1
2_|400867Decal, Square "Green Light"2
3 | 400868Decal, "Insert Coins"1
4 | 400869Decal, “Start Button"1
5 | 400870Decal, "How to play"1
6 | 400871Decal, "Don't Let the Enemy..."1
7_|400873Decal, Monitor Glass1
8 | 400866jecal, Gun Pedestal Side2
9 | 400865Decal, Control Cabinet Side2
10 | 400874[Plexigiass, Printed Marquee1
Page 21

2 Game seitings

2-1 Checking the game start up

When the power switch is turned ON, the self-diagnostic test will get started. The test results will be displayed on the screen. The power does not turn ON if the back door is not tightly fixed.

WResult of self test lf test is OK.

  • The machine goes to the game mode and the demonstration game gets started. If “BAD” or “ERROR” appears onscreen, take proper measures, referring to “4 Troubleshooting” on page 35.

c_Getting started after conversion

  • When the machine gets started for the first time after conversion, the following message appears on the screen. Press the test button on the service panel.

BACKUP DATA ERROR

SCOPE SCREEN ADJUST DATA GUN VOLUME DATA PRESS TEST SWITCH to FACTORY/DEFAULT SETTINGS ‘AND MANUAL TEST MODE

Now the message below appeai Press the test button once again.

The main menu screen reapnears with “>” and “<” displayed flashing before and after the next item. Select and enter the mode, and go to the adjustments. + GUN CHECK... +. Page 22

  • SCOPE SCREEN ADJUST .... page 23
  • BOOKKEEPING ... + page 28
  • If the system clock is not set, “> <” is also displayed flashing before and after “BOOKKEEPING” to prompt you to make the time setting.
  • If an error occurs with “SCOPE SCREEN ADJUST DATA” or “GUN VOLUME DATA’ at the startup, “> <” is displayed flashing before and after the “SCOPE SCREEN ADJUST’ or “GUN CHECK”. Call this item and make necessary settings and adjustments. The “GAME MODE’ items are not displayed until these settings are made, which means the game cannot be played.
Page 22

2 Game settings

2-2 Setting and adjustment of game mode

Manually check and change the settings for the screen displays and game contents and change them as required. WiStarting the test mode = me am mm me me me ee ee 1 Turn ON the main power switch. 2 While the demonstration game is playing, press the test button on the service panel. (Do not turn ON the main power switch with the test button held down. The current settings as well as the BOOKKEEPING data will be erased and the machine will revert to the factory settings.) ‘The main menu is displayed on the screen. Wi Quit the manual test mode mv mms me mm a oe ee ee 1 Pull the rifle unit's trigger to select “GAME MODE’ on the main menu screen. 2 Press the start button. -The screen returns to the game mode. a <r s Main menu screen (basic items) Displaying the products destination and version. Checking the controls. —>Page 21 MAIN MENU + Checking the performance of the rifle unit. age 22 YO CHECK —————___—_______} Adjusting the monitor screen distortion. GUN CHECK ~->Page 22 SCREEN CHECK Adjusting the scope screen position. SCOPE SCREEN ADJUST -->Page 23 COLOR CHECK. ——————______—___ ‘Adjusting the display color. DISK MEDIA CHECK § ———————_—____—_ ~>Page 23 €.G, BOARD CHECK ‘Checking the content of the DISK MEDIA . SOUND OPTIONS ~>Page 24 GAME OPTIONS Checking board performance. COIN OPTIONS —————__________ ~>Page 25 Setting various sound options. BOOKKEEPING ——————______—_ ~>Page 25 ALL FACTORY SETTING Setting various game options. GAME MODE “| ~>Page 26

PRESS START BUTTO!

Displaying the bookkeeping information of coins. —>Page 28 Retuming all the settings to factory ones. ~>Page 30 Retuming to game mode. Selecting each mode @ 2 2 2 SS 2 a eee How to select each mode from the main menu. -SELECT --> Pull the rifle unit's trigger. “SET --> Press the start button. After selecting a mode, refer to the page on which that mode is described in details. Wetting the time me a a ms ae oe If the timer is not set yet in the ‘BOOKKEEPING’, the following message appears on the screen. “PLEASE SET the TIME for the BOOKKEEPING” Press the test button, and the “MAIN MENU” screen shows up instead in the test mode. Select the “BOOKKEEPING” screen and set the time. Without this setting, the above message appears each time the machine gets started.

Page 23

2 Game settings

2-3 Mode descriptions

MThe original factory settings are displayed in green; the changed settings are displayed in red. ‘Pull the rifle unit's trigger to select a setting to be modified, and press the start button to change the setting. ‘After the setting has been changed, select “SAVE AND NEXT” and press the start button for entry. “NOW SAVING?” wiil appear, the modified settings will be saved, and the screen returns to the main menu. ‘If “EXIT” is selected after the modification of the settings, the following message will appear. “YOU DID NOT SAVE. DO YOU WANT TO SAVE? YES/NO’ select “YES” or “NO”. Pull the rifle unit’s trigger to select “YES” or “NO”. Press the start button for entry. If “YES” is selected, the new settings will be saved with “NOW SAVING’ displayed and the screen will return to the main menu. If “NO” is selected, the message “NO MODIFY SETTINGS’ will appear, the modified settings will not be saved, but the main menu will show up again on the screen.

*lf “FACTORY SETTINGS’ is selected and the start button is pressed, all the settings of the mode will go back to the factory ones. *if ‘DEFAULT SETTINGS?’ is selected, the settings of the mode will become the default ones. SE ——OOOOO MEMO

Checking the controls MMode for checking the performance of the controls. To return to the main menu screen, pull the rifle unit’s trigger while pressing the start button. according to th the input. VO CHECK itoh turr “OFF. ‘Switch turned OFF. ‘Switches on and off the scope by holding down the service ‘andltest buttons at once .Grid pattern on the scope screen. ‘Nothing on the scope screen. Press the start button and the ON/OFF (Lights up/Goes up status changes alternately. Lights up. 1@ hexadecimal value corresponding to the Tight-and-lott motion.

rking shits to LERT when the rifle points

to RIGHT when rightward. ‘Detects the backlash between the rifle unit's right / left control gears. ‘Displays the hexadecimal value corresponding to the Lunia up-and-down motion “Thi jt ‘The shits © BOTTOM when the rie points This screen is just an example. Gowniwa ark nay obes io BC Tpward Poir Detects the backlash between the rifle unit's up / down control gears. ‘Holding down the start button, press the test button and you can see the DIP switch settings on the PCB unit.

Page 24

2 Game settings

N CHECK Checking the performance of the rifle unit Mode for adjusting and checking the rifle unit's swing range. Look at the screen for the marker that the gun barrel is pointing to. If the marker is extremely out of position, press the test bution on the service panel to call the gun adjustment mode. To return to the main menu screen or interrupt the gun adjustment mode, press the start button.

Gun check mode

Marker Make sure the marker is whare the gun barrel is pointing to.

Butiot mark Pull the rifle unit's trigger and make sure the bullet mark appears,

This screen is just an example. Gun adjustment mode This mode is intended to adjust the aim of the rifle unit. Take the following adjustment procedure. 1 Point the gun barrel to the lower-left corner of the screen, and pull the rifle unit's trigger. 2 Point the gun barrel to the upper-right corner of the screen, and puil the rifle unit's trigger. 3 The “NOW SAVING” message appears and the settings will be saved. Then the “GUN CHECK” screen shows up again. Move the rifle unit and make sure the marker is in position.

¢lf an error happens in “GUN VOLUME DATA” at the start of the machine, the “Gun adjustment mode” screen appears automatically. *No image appears on the scope while in the “Gun check mode” and “Gun adjustment mode”. MEMO

SCREEN CHECK

Adjusting the monitor screen distortion @Mode for checking the monitor screen display. Adjust the focus, distortion and size of the image on the screen while watching the crosshatch pattern. Use the monitor adjustment PCB to make adjustments. To return to the main menu screen, press the start button.

Page 25

2 Game settings

SCOPE SCREEN ADJUS

Adjusting the scope screen position Mode for adjusting the display position on the scope screen. Pull the rifle unit’s trigger to select an item. Press the start button to modify the setting. Looking into the scope, adjust so that the crosshatch pattern is centered. To return to the main menu screen, select “SAVE AND EXIT” or “EXIT” and press the start button.

SCOPE SCREEN ADJUST

X-5 ¥: § Displays the displacement from the default settings. up Used to move up the scope screen by pressing the Down, ————___—______J start button. LEFT RIGHT ‘Used to move down the scope screen by prassing the start button,

DEFAULT SETTINGS

‘SAVE AND EXIT ‘Used to move the scope screen to the left by pressing EXIT the start button.

Used to move the scope screen to the right by pressing the start button. Used to move back the scope screen to the default settings by pressing the start button. *This screen is just an example.

*The crosshatch pattern may appear slightly tilted on the scope screen. The game is not affected, however.

MEMO

COLOR CHECK

Adjusting the display color MMode for checking the display color. Make the adjustment using the monitor adjustment PCB so that the colors of the color bars should appear properly graduated and the background should become black sufficiently. To return to the main menu screen, press the start button.

Page 26

2 Game settings

DISK MEDIA CHEC Checking the disk media MiMode for checking the DISK MEDIA. In this mode, the disk media check sums are checked one after the other. “OK” appears on the screen when no problems are detected, “BAD” if a problem occurs. When the game is put into this mode, the check starts automatically. Press the start button to interrupt the checking or return to the main menu screen.

DISK MEDIA CHECK

DISK MEDIA CHECK

100. ———__——— ‘Counts down from "100" ‘Checking is complete when "0" is reached

PRESS STARTBUTTON = CANCEL

When the disk media has been completely checked, “OK” appears.

DISK MEDIA CHECK OK

If anything wrong is found in check, “BAD” appears.

DISK MEDIA CHECK BAD

If “BAD” appears, immediately turn “OFF” the main power switch, unplug the AC power cord from the machine and contact your nearest KONAMI approved dealer.

Page 27

2 Game settings

BOARD CHECK Checking the C.G. board performance MMode for checking the C.G. board function. Check the function of the C.G. board by watching the motion on the screen in this mode to see if the board works normally or not. To return to the main menu screen, press the start button.

‘Two tuming cubes zoom in and out repeatedly behind ‘the . (Two cubes marge together from time to time.)

Pe

‘The product logo mark flashes translucent here. (The same logo mark appears in the scope.) ane

SOUND OPTIONS Setting various sound options Mode for setting and checking the sound options. Pull the rifle unit's trigger to select an item. Press the start button to modify the setting. To return to the main menu screen, select “SAVE AND EXIT” or “EXIT” and press the start button.

Th and off the demo und. SOUND OPTIONS UTNE TIME ee

SOUND IN ATTRACT MODE

ALL THE TIME VOLUME SETTING 20 ‘Adjusts the sound volume level of voice and sound effects Eee in the range of 0 (mute) to 30 (maximum). “To raise the sound level, press the start button. “To lower the sound level, press the start button so many times that the zero level is reached and make a new setting. FACTORY SETTINGS. ——————_—__—_____ SAVE AND EXIT ‘You will hear a do-re mi...do musical scale from EXIT the left speaker first and then from the right ‘speaker, which is repeated twice. (Sound affect is given for the 2nd round.) SCALE CHECK BGMINGAME MODE ON

PULL GUN TRIGGER = SELECT OPTION h a panes START EUTrONe exECUTE Sets to give background music while the game is being ON son Background music heard, *This screen is just an example. -OFF....... Background music nat heard.

Press the start button to return all the settings to the factory settings.

Page 28

2 Game settings

GAME OPTIONS

Setting various game options MMode for setting and checking the game options. Pull the rifle unit's trigger to select an item. Press the start button to modify the setting. To return to the main menu screen, select “SAVE AND EXIT” or “EXIT” and press the start button. Satya cies lel rm te Sor, 1:EASIEST .. ces 2ERY EASY ‘S:EASY 4:MEDIUM...

Makes 7 initia! settings for the players condition ‘guage. (displayed in percentage.) {50, 80, 100, 120, 150, 200%) Sets the violence level when enemies are hitin play or during demo scenes. STRONG ... Hit effect on the haad displayed onscreen, "MILD. fit effect not displayed onscreen. Sets the hit effect when an enemy is gunned down, GAME OPTIONS + FLASH ..... Flashing DIFFICULTY LEVEL START CONDITION VIOLENT MODE Red effect spurts. Blue effect spurts, Green effect spurts, HIT EFFECT NIGHT MODE BRIGHT SCOPE IN ATTRACT MODE REAL TIME WINDOW

INTERNET RANKING RECORD SAVE RECORD DATA CLEAR

  • YELLOW..... Yellow effect spurts. Adjusts the dark-acene brightness from 1 to 16. ‘Awindow appears on the right of the screon with ladies at the left front, at the center, and at ight in the background. ‘Adjust so that the lady at right in the background disappears. Decides on whether the scope-screen image is displayed ‘on the main screen during the demonstration game. " COMPLETELY OFF.Of al the te (scope sereon image net displayed). Scope-screen image tumed on whan teres an pout during the demonstration gar But automatcaly umed off there Is no input/output for 30 seconds (effective to prolong the LCD's backlight le.)

Sets the window on the main screen EVENT AND SCOPE.....Displayed by stationary ‘camera when an enemy Is hit or the boss focused ‘on. Scope screen in other cases splayed by stationary camera when an enemy is hit or the boss focused on Scope screen all the time FACTORY SETTINGS SAVE AND EXIT enn + AUTO CONTROL

PULL GUN TRIGGER = SELECT OPTION PRESS START BUTTON = EXECUTE

ALWAYS SCOPE.. ‘Sets whether or not to display the INTERNET RANKING password OFF.

Press the start button to return all the settings to the factory settings.

Page 29

2 Game settings

COIN OPTIONS

Setting various coin options MMode for setting and checking the coin options. Pull the rifle unit’s trigger to select an item. Press the start button to modify the setting. To return to the main menu screen, select “SAVE AND EXIT” or “EXIT” and press the start button.

Selects free play mode. COIN OPTIONS + YES........Available for free play. FREEPLAY NO —_——— * NO. Not available for tree play. ‘Always keep it set to COMMON. EDIT OT2 1COIN(S) 1CREDIT( ‘Sets the number of credits for the coin. (Presettable to 16 coins for 1 credit through 1 coin START 2CREDIT(S) to START —————— for 16 credits)

CONTINUE —1CREDIT(S) to CONTINUE

Sets the number of credits required to start the FACTORY SETTINGS —————_—____— ame! SAVE AND EXIT Presettable to 1 thru 16 credits) ‘Sets the number of credits required to continue the amo. Presottabie to 1 thru 16 credits) Prass the start button to return all the settings to the factory settings.

“This screen is just an example.

Page 30

2 Game settings

BOOKKEEPING Displaying the bookkeeping information of coins ™Mode for displaying the total data on the number of coins put in the machine. If the time is preset on the “CLOCK SETUP” screen, the total data on the number of coins put into the machine can be checked for each coin slot. Pull the rifle unit's trigger to select “HOUR”, “MINUTE”, and “SECOND”. Press the start button to adjust the current time. Make sure the current time is correct, select “SAVE AND EX!T” and press the siart button. (The current time is now set and the main menu screen shows up.)

BOOKKEEPING

CLOCK SETUP

SETTO HOUR : MINUTE. : SECOND

SAVE AND Ext? ————_——— EXIT ———_—_—— 7

=H Retum to main menu with time saved

SYSTEM CLOCK 620 -Retum to main menu without saving time

PULL GUN TRIGGER = SELECT OPTION PRESS START BUTTON = EXECUTE

This screen is just an example.

*lf the time setting has not been made — for example, after the machine has been set up or initialized —, the “CLOCK SETUP” screen shows up. “When the time setting has been modified, the bookkeeping information is automatically cleared. With the current time not set, the total of received coins and other bookkeeping data are not displayed. (The data once erased can not be resumed.) MEMO

When the time has been preset on the “CLOCK SETUP” screen as shown above, the following “BOOKKEEPING?” information is displayed on the screen. Select “NEXT DATA SUMMARY’ and press the start button, and the screen will switch in the following sequence. To return to the main menu screen, select “EXIT” and press the start button.

Total number of Total number off "Total number of Indication of Total number of

coins for last coins for past 52 coins for each slay eonditi 7 days wae Pest Ea Event —

Also, when the current time has been set and “INCOME DATA CLEAR’ has been selected and the start button pressed, the current time and BOOKKEEPING data can be cleared. At this time, the question “DO YOU WANT TO CLEAR DATA? YES/NO” is indicated on the screen. Pull the rifle unit's trigger to select “YES” or “NO”. If “YES” is selected, “NOW CLEARING” appears on the screen and the “BOOKKEEPING” data will be deleted. The data will be saved in the factory settings and the main menu screen will show itself up. If “NO” is selected, “NO MODIFIED” is indicated and the main menu appears again without deletion of the data.

Page 31

2 Game settings

Screen of the total number of coins for last 7 days BOOKKEEPING COIN DATA OF LAST 7DAY S.o: store 700 Number of coins of today. ° Avarage number of colns of last 7 days. Tolal number of coins after the time being set. 120 ‘Number of coins of yesterday, Number of coins of 2 days ago. Number of coins of 3 days ago. ‘Number of coins of 4 days ago. ‘Number of coins of 5 days ago. Number of Goins of 6 days ago. Number of coins of 7 days ago. 0" appears for the day whose data is not totalled, joes (9 the next date. lears the current time and the income date. *This screen is just an example. Screen of the total number of coins for past 52 weeks

BOOKKEEPING ee oe ‘Number of coins of 1 week before. on 9 lumber of coins of 2 weeks before. ‘Number of coins of 3 weeks before,

"0" appears for the wosk whose data is not totaled. Displays the total numbar of coing for the cain slott and slo. ‘Goes to the next date. Clears the current time and the income date.

¢This screen is just an example. Screen of the total number of coins by hours and days of the week

Total number of coins since the setting of time. ‘Number of coins for Sunday. Number of coins for Monday. Number of coins for Tuesday, ‘Number of coins for Wednesday. Number of coins for Thursdzy. Number of coins for Friday. Number of coins for Saturday. "0" appears for a day of the week whase data is not totalled. Goes (o the nex date. ‘Clears the current time and the income date. This screen is just an example. Screen of indication of play conditions BOOKKEEPING A " ‘otal active time since the setting ol time. ‘Total piay time since the setting of time. A time oe Shorest play time. Teial count for coin slat 1. ‘Total count for Coin siot 2 Tolal pay time since the seting of time ‘Total ital play rounds since the seting of time. ‘Total continue play rounds since the selting of time, Goes to the next date. Clears the current time and the income date.

«This screen is just an example.

Page 32

2 Game settings

Screen of the total number of coins per hour

BOOKKEEPING

COIN DATA OF EACH HOUR

: 4 16:00 Total number of coins per hour. 02:00 10:00 5 03:00 41:00 “0” appears for the hour whose data is not totalled. Displays the total number of coins for the coin slott and slot, Goes to the next date. Clears the current time and the income date.

PULL GUNTRIGGER = SELECTITEM

PRESS START BUTTON = EXECUTE

*This screen is just an example.

FACTORY SETTINGS

Returning all the settings to factory ones Mode for returning the test-mode settings to the factory settings. Pull the rifle unit's trigger to select “YES” or “NO” and press the start button for entry. If “YES” is selected, the question for re-confirmation appears on the screen. If “YES” is selected again, the “NOW SAVING” message appears on the screen and the test-mode settings, are saved as the factory settings.

  • SOUND OPTIONS
  • GAME OPTIONS ¢ COIN OPTIONS

It“NO” is selected, “NO MODIFY SETTING’ is indicated. This means the modified settings are not saved.

Page 33

3 How to play

This gun shooting game is designed to allow you to look into the scope of the rifle unit and shoot at enemies. You can see telescopic and night vision images that are not clearly displayed onthe main monitor screen. Search for targets quickly and shoot them with pinpoint accuracy & precision.

MHow to play the game = em me me ee oe ee ee

1 Put coin(s) in the slot and press the start button once.

2 The play mode selection screen shows up. Within 15 seconds, move the rifle unit to select a play mode. Pull the trigger to enter your choice. (you may press the start button instead to enter a choice.)

*SHOOTING RANGE mode.....You try to get the highest score possible within a certain period of time in the shooting range. STORY... .0+ssssersseesetesssseerenesesee YOU Will be a sniper of a special anti-terrorist squad, stationed in the story to counter frequent terrorist activity. *SHOOTING RANGE mode You can keep playing the game until the preset time is ‘0’. The game is over at this point. Each time a target is hit, your score increases. (The score value is different depending on where the bullet hits.) The game is over when you successfully hit the last target. The remaining time is added as a bonus to your score and the final score is displayed.

3 With the play mode selected, the game starts automatically. Watch the monitor screen and search for an enemy. Look into the scope and shoot the the enemy. Initially, the rifle is loaded with 5 bullets, but will reload automatically and is limitless. From the second stage, you can select a mission or route. When a mission has been successfully completed, you can go to the next stage. If not however, the mission select screen shows up again. (You can now select another mission not yet played, or an aborted mission again.) You can keep playing the game until the condition gauge on the screen reaches ‘0’. The game is over at this point. The ‘STORY’ mode ends in TWO ways, ‘HAPPY ENDING’ or ‘BAD ENDING.........

Page 34

3 How to play

The condition gauge gets boosted in the following cases: When an enemy has been hit. When a mission has been successfully completed. (A bonus is added according to the performance evaluation.) When a woman (in a nurses uniform) appearing in certain scenes has been caught in the scope for a certain period of time. The condition gauge gets reduced in the following cases: If a civilian, not an enemy, has been hit. If you have been attacked by an enemy. If a mission has been aborted. The gauge drops gradually with the passing of game time. Setting the hit-effect when gunning down enemies = == ====2===— On this machine, the violence expression when an enemy is hit can be chosen from several options.

Continuing the game === === —====5 858888888888 ==8=

The game can be continued within 10 counts after a game is over. There are some scenes and modes in which you cannot continue.

Page 35

4 Troubleshooting

If the power switch is turned ON but the machine fails to start properly, take the following measures. If the machine still malfunctions or any other problem than described below occurs, immediately turn OFF the main power switch, unplug the power cord from the receptacle and contact your nearest dealer.

No image on main screen, title unit fluorescent light failure to light up. *No power tumed ON.

*Power cord disconnected from the machine or wall outlet.

Circuit protector activated. *Tum ON the main power switch. Check also the shop’s circuit breaker.

*Reconnect the power cord tightly.

*Take measures, referring to the machine’s Operator's Manual.

No image on screen : title unit fluorescent light on. *Memory card not or loosely inserted.

*Some connectors disconnected or wires broken.

PCB unit defective.

Monitor defective. *Check the memory card for wrong position.

Turn OFF the main power switch, unplug the power cord from the receptacle and check all the connectors for poor contact. If all the connectors are tightly connected but the same trouble occurs, contact your nearest dealer.

«Immediately turn OFF the main power switch, unplug the power cord from the receptacle and contact your nearest dealer.

Title unit fluorescent lamp failure to light up. Fluorescent lamp or glow lamp broken. Replace the fiuorescent lamp or glow lamp with new one of the same type.

Screen too dark or too bright. *Monitor maladjusted. *Readjust the brightness on the monitor adjustment PCB.

Start button malfunctioning. Switch wires and connectors disconnected from start button.

*Start button defective. Reconnect the switch wires and connectors to the socket.

*Replace the start button with new one.

Page 36

4 Troubleshootiing

Coin selector malfunctioning.

No sound or too loud (or too soft) sound. Coin selector defective. *Check the performance on the “VO CHECK” screen. lf malfunctioning, replace the coin selector or microswitch with new one.

*Sound level maladjusted. Make proper setting on the “SOUND OPTIONS” screen.

Game started, but no image on Scope screen. Wires (connectors) disconnected on PCB unit. *Check to see if PCB unit wires (connectors) are all connected.

Rifle unit's trigger malfunctioning. «Wires (connectors) disconnected on PCB unit. *Check to see if PCB unit wires (connectors) are all connected.

“BAD” displayed on the “DISK MEDIA CHECK’ screen in test mode.

“HARDWARE ERROR (***)” displayed on screen: game failure to start. *Memory card defective. Immediately turn OFF the main power switch, unplug the power cord from the receptacle and contact your nearest dealer.

*Something wrong with the “Write down the error code hardware. displayed. Immediately turn OFF the main power switch, unplug the power cord from the receptacle and contact your nearest dealer.

“OK” appears at the initial device check, but this check is repeated without going to the game mode. *Some connectors disconnected or wires broken. Turn OFF the main power switch, unplug the power cord from the receptacle and check all the connectors for poor contact. If all the connectors are tightly connected but the same trouble occurs, contact your nearest dealer.

Page 37

5 Annex

5-1 Exploded view

HRFIG.1 ONUT, ROFL me oe a

ao i i al yt | (Eva : EAB

Be il | il gles] | EISEl8

Page 38

5 Annex

HEFIG.2 ASS’Y, SCOPE. = = me men mes oe ee oe

5 ; a

ils lal | HGH GAG [eleg| (Il lsal (2eTeLee] (RIIEN FEAL UI] Die | lated SEI aa ABELL LT LLL HLL al leet fatal (aisle! (slalslsls| (Sisisislele we. of oy ic

Page 39

Ue a a eee TINH ‘ASSY &Dis Xx@UUY G

Page 40

5 Annex

HNFIG.4 UNIT, MECHANISM = me ms oo

[5] zg ele fed 3 = Ed FI RIKKI [elalafal—-[ [=i rele) S PRtiereciricarion pry] Nore RI-25 EWS-UOAS25E53 JOR-S- 15X25 NB-35, wR PHC 10.5 wuz vo. ‘NO IN . E! . Fi SCREW, CROSS PAN SEMS [M@xi0 BOLT. HEX SOCKET CAP —|WOxt8

BASE ‘02 | 500878 |RUBBER, STOPPER 03] 500005 |BRACKET, BEARING [GEAR

[SPACER

GEAR BRACKET, P. METER FRAME FRAME. 10 s00873_|PIN, STOPPER 61] s00est_|STOPPER, RUBBER 65] 00814 | SUSPENSION, RUBBER 22] so0s23 _|WIRE

Page 41

5 Annex

5-2 Wiring Diagrams

Page 42

Hea oa ROB! en = = ‘naex Suze oo” ave ne

qnercsur-aa] | xs 14 am + > oreex RGB2 em ==Es ey ismwe = ze PCB BOX

pers

Som COUNTER? Lae came? SP+ SP. rc

i} !

' ' ' com comrrent t

I \

' '

i}

i I i stinnSabbbentis

oor} Inep-sur-aan ities 3383585555558

cmao

ccm7| wa suP-aa g

en rc

The sections in broken-lined boxes denote the wires of the machine.