Battlezone Cabaret DP-166-1st-01B
Battlezone (rev 2) (Atari, 1980) · Drawing Package · 1 pages · original scan

Figure 1
AUXILIARY PCB [000000000000
PORTION OF AUXILIARY PCB
Sheet 1, Side B
1DP-166.01 1st printing Figure 2A Figure 2B
PORTION OF AUXILIARY PCB
4FUF
92F3 Aas 3050 H8F9
The Auxiliary PCB Math Box Circuitry
‘The Math Box Circuitry of the Battlezone Auxiliary PCB is connected to the Analog Vector-Generator PCB vi the PCB harness interconnector. The Math Box Circultry receives addresses EABO thru
EABA (external address bus 0 thru 4) and provides data EDBO thru
£EDB7 that results inthe three-dimensional video of the Battiezone™ ‘game.
{A second connector on the Auxiliary PCB connects the control
signals ofthe signature analyzer (SA). This header accepts a special
hamess connector that makes signature analysis extremely easy.
GND Signature Analysis of the Math Box Circuitry During the self-test procedure, the Math Box Circuitry is quizzed. T displayed in the upper rightshand comer of the self-test video display indicates that the Math Box Circuitry does not answer the
uestion in the amount of time expected. Therefore, aT indicates a
Math Box Circuitry failure,
Due to the complexity ofthis cicultry, we offer signature analysis a8 a simple means of Isolating falling circuits. Signatures for this Circuitry are presented in two forms:
- at the actual test points in the Auxiliary POB Math Box Circuitry schematic diagram (on Sheet 3, Side 8), and
- foryour convenience, onthe detail drawing ofthe Auxiliary PCB. to the left of this text
Since the Analog Vector-Generator PCB must be connected to the Auxiliary PCB, you may take signatures while the PCBS are in stalled in the game.
The following Is the procedure for signature analysis of the Math Box Circuitry of the Auxiliary PCB:
A. Equipment Required:
- Signature Analyzer (one ofthe following: lati CeAeT ComputerAssisted Troubleshooter. This is a signature analyzer and a RAMIROM tester combined. For more information contact Ala, Ine, Feld ServiceCoin-Op Division, P.O. Box 427, Sunnyvale, CA 84086. oR KureKasch Signature I! signature analyzer For more informa: tion contact KurzKaseh, 711 Hunter Drive, Wilmington, Ono 457, on Hewilot-Packard Model S004A signature analyzer. For more information contact Hewlet Packard, Scientific iniruments DW, 1801 Page Mill Road, Palo Alto, CA 94308, For local dealer, chock the Yellow Pages under “Electronic Equipment and Supplies”
883A 1074 20P9 Figure 3 nape
H/J2
S255 Saag PORTION OF AUXILIARY PCB S.A. Hamess Assembly 12cIRCUMT HOUSING MOLEX PLN. 0850-7121
ono -
cock i. r] TERMINAL START. - MOLEX P.N. 08-50-0106 Sean ote stop
#23951 #33951
SA Harness Assembly: Atari part numbor AG3683601. You can make one of these yourself. Above Is an illustration ofits construction. ‘Three Jumper wires with “hook” connectors on each end, Pullup resistor as follows: 1K to 1.5K ohm, v4 watt resistor.
Signature Analysis Setup Procedure Connect Signature Analyze tothe matching pins of SA con nector on tho SA Hamoss assembly. In other words, GND Should matchup with GND, ete.
Set Self-Test Switch of Battlezone™ game to ON. Alter approximately three seconds, the TV monitor should display the selt test patter.
‘Jumper top end of 1K:ohm resistor 129 (located immediately between and below C [center] and L [let] COIN test points) of Analog Vector-Generator PCB to ground five times, or until video display is blank. You will hear a short beep after the Sth grounding; also, the screen will display only a tiny dot in its Center. NOTE: To avoid accidentally turing off the game by brushing against the interlock switch, we recommend putting tape over the switch, ‘Altemate: Jumper pin § of Analog Vector-Generator PCB edge- Gonnectr J20 to ground five times, or unt vdeo espa is
C. Signature Analysis Test #1 Procedure lug_SA Harness Assembly Test #1 connector onto Signal ‘Analyzer header on Auxiliary PCB (the black wire on the conrector should be at the top).
Connect jumper between pin 1 of IC 86 on the Analog Vector-Generator PCB and ground, This places a continuous RESET to the microprocessor on the Analog Vector-Generator Pos.
Set Signature Analyzer START to _/~ , STOP to /~, and ‘CLOCK to_—
Connect a jumper wire to each end of a 1K to 1.6Kohm resistor. Connect one jumper wire to + SV test point on AUXlary POB. Connect other jumper wire to the tip of the Signature Analyzer probe.
Verity that setup procedure was correst by probing (touching probe to) the + 5V test point. The Signature Analyzer should Indicate C34. If not C34, remove the jumper from pint of IC B6. Retumn to B. Signature Analysis Setup Procedure and once again do step 3.
Probe for signatures as shown in Figure 1 to the left. If all signatures are correct, continue with D. Signature Analysis Test #2A Procedure. i any signatures are incorrect, probe for signature of CC34 on +5V test point. If not COSA, remove jumper from pin 1 of 1G B6. Return to B. Signature Analysis Setup Procedure ard once again do step 3. If +5V is CC34, reer to G. Isolating a Failing Circult.
‘Signature Analysis Test #2A Procedure Remove 1K to 1.5Kohm jumper wire from Signature Analyzer probe.
Plug SA Harness Assembly Test #2 connector onto Signature ‘Analyzer header on Auxiliary PCB.
Remove jumper from pin 1 of IC BS on the Analog Vector: Generator PCB.
‘Set Signature Analyzer START to_/~ , STOP to —\., and CLOCK to
Verity that setup procedure was correct by probing + SV for a signature of 3951. If not 9954, return to B. Signature Analysis Setup Procedure and once again do step 3, then return to this step.
Probe for signatures as shown in Figure #2A to the left. fall signatures are correct, continue with E Signature Analysis Test #28 Procedure. It a signature is incorrect, refer to G. Isolating a Falling Circutt. E. Signature Analysis Test #2B Procedure
- Make sure the SA Hamess Assembly Test #2 connector is plugged onto Signature Analyzer header on Auxiliary PCB.
- Make sure jumper is removed from pin 1 of CB on the Analog Vector-Generator PCB.
3, Set Signature Analyzer START to_/~ , STOP to —\_, and CLOCK to“.
- Verity that setup procedure was correct by probing +5V for a signature of 3951. If not 3951, retun to B. Signature Analysis ‘Setup Procedure and once again do step 3, then return to this step.
5, Probe for signatures as shown in Figure #28 to the left. I all ‘signatures are correct, continue with F. Signature Analysis Test 143 Procedure. ta signature Is incorrect, refer to G. Isolating @ Failing Circuit.
F. Signature Analysis Test #3 Procedure Plug SA Hamess Assembly Test #3 connector onto Signature ‘Analyzer header on Auxiliary PCB.
- Make sure jumper is removed from pin 1 of IC B6 on the Analog ‘Vector Generator PCB.
- Set Signature Analyzer START to_/~ , STOP to, and CLOCK to
- Verity that setup procedure was correct by probing +5V for £3951. If not 3951, return to B. Signature Analysis Setup Pro- ‘cedure and once again do step 3, then return to this step.
- Probe for signatures. as. shown. in Figure. #3.to. the left fall signatures are correct, then Math Box Circultyy of Analog Vector Generator PCB is OK.
G. Isolating a Failing Circuit '¥ you find an incortet signature, tind the signature test point of the Math Box Circulty on Sheet 3, Side B, Locate the IC from which the signature is being output. Check al inputs ofthat IC Hall input signatures are correct: Remove the Auxillary POB from the circult. Check the circuit traces common to the falling IC pin on both the top and bottom of the PCB for shorts to another circuit ‘race Ifthe lrcult traces are not shorted, then replace the falling IC. Han input signature is incorrect: Locate on the schematic the IC ‘source of the failing signature. Check the input signatures of that IC. fall input signatures are correc, then that isthe failing I. If this [Chas a falling input signature, then continue “upstream” in the cir- Cult flow until the failing IC is isolate.
A. ATARI
BATTLEZONE™
CABARET
Auxiliary PCB
Signature Analysis Procedure
Section of 035678-01 A