CATHODE RAY TOMES

Midway Sportstation 25in Conversion Kit

NBA Showtime Gold Edition / NFL Blitz 2000 Gold Edition (Midway, 2000) · Kit Manual · 128 pages · 51 sections · original scan

Page 1

FEBRUARY 2000 Cb MIDWAY 16-15909-101 www.midway.com

4-PLAYER, 25”

VIDEO GAME CONVERSION KIT

Dual Product with Player-Selectable Games

e1-Assembly ¢2-Operation 3-NFL Audits 4-NBA Audits 5-Wiring 6-Troubleshooting

Midway Amusement Games, LLC — 3401 North California Avenue, Chicago, Illinois 60618-5899 USA

Page 2

Midway Amusement Games, LLC — 3401 North California Avenue, Chicago, Illinois 60618-5899 USA

Page 3

NBA SHOWTIME Gop Eoirion/ NFL Bi1z72000 Goin Ebivion

CONVERSION KIT

CHAPTER

ONE

ASSEMBLY

WARNING: Use of non-Midway parts or circuit modifications may cause serious injury or equipment damage! Use only Midway authorized parts. For safety and reliability, don’t substitute parts or modify Midway products. Substitute parts or modifications may void EMC directive or FCC type acceptance.

NOTICE: The term VGM refers to the video game machine.

Assembly 1-1

Page 4

SAFETY INSTRUCTIONS

The following safety instructions apply to operators and service personnel. Read these instructions before preparing your video game machine (VGM) for play. Other safety instructions appear throughout this manual.

DEFINITIONS OF SAFETY TERMS

DANGER indicates an imminent hazard. If you fail to avoid this hazard, it will cause death or serious injury.
WARNING indicates a potential hazard. If you fail to avoid this hazard, it could cause death or serious injury.
CAUTION indicates a potential hazard. If you fail to avoid this hazard, it may cause minor or moderate injury. CAUTION also alerts you about unsafe practices.

NOTICE indicates information of special importance.

WARNING: DISCONNECT POWER. Always turn the power off and unplug the VGM before attempting service or adjustments. Installing or repairing PC boards with power on can damage components and void the warranty. Be sure that you securely install ground wires.
WARNING: GROUNDING. Avoid electrical shocks! Don’t plug in a VGM until you have inspected and properly grounded it. Only plug this VGM into a grounded, three-wire outlet. Don’t use a “cheater” plug, or cut off the ground pin on the line cord.
WARNING: SALVAGED PARTS. Kit completion requires salvaging parts from old VGMs. Salvaged parts must operate perfectly. Otherwise, the converted VGM can’t perform properly or safely. Before you attempt conversion, repair circuit board malfunctions and cabinet damage.
WARNING: HANDLE FLUORESCENT TUBE AND CRT WITH CARE. If you drop a fluorescent tube or CRT and it breaks, it will implode! Shattered glass can fly eight feet or more from the implosion. PHI OF
WARNING: HAZARD TO EPILEPTICS. A small portion of the population has a condition that may cause epileptic seizures. Affected persons experience seizures while watching some television pictures or playing certain video games. People who have not had seizures may still have an undetected epileptic condition.

If anyone in your family has experienced epilepsy symptoms (e.g., seizures or loss of awareness), consult your physician before using video games.

While children play video games, a parent should observe. Be alert to the following symptoms: Dizziness, altered vision, eye or muscle twitching, involuntary movements, loss of awareness, disorientation, or convulsions. If you or your child experience these symptoms, discontinue use immediately and consult your physician.

Assembly 1-2

Page 5
CAUTION: HANDLING ELECTRONIC DEVICES. This kit’s electronic components are sensitive to static electricity. Before handling electronics, observe the following precautions...

¢ Before servicing electronics, turn off AC power to the VGM. ¢ Before handling electronics, discharge static electricity on your body. Touch the power supply’s safety ground stud before touching electronics. ¢ Store electronic assemblies in an anti-static area. Use an anti-static bag to store the CPU board assembly. After you install the new unit, reuse the same bag to protect the old CPU board. e Don’t remove or connect electronics when cabinet power is on. Otherwise, you'll damage VGM electronics and void your warranty.

CAUTION: USE PROPER FUSE. Avoid electrical shock! Replacement fuses must be of the same type as those they replace. Fuse voltage and current ratings must match ratings on the original fuse.
CAUTION: WIRING. This kit uses as much of the existing wiring as possible. Avoid improper operation! After you complete the conversion, but before applying power, check the wiring. Verify that the wiring matches the diagrams.
CAUTION: TAKE CARE WHEN SHIPPING HARD DISKS. The hard disk drive must be packed in an anti-static bag. When shipping the drive for repair or replacement, pack it in an approved container (P/N 08-8068). Never stack or drop hard disk drives. |}PR B

NOTICE: POWER SUPPLY. Be sure that your old VGM’s power supply can produce these voltages and currents: +5VDC at 6A, -5VDC at 1A and +12VDC at 4A. Meter these operating voltages before you disconnect the old electronics from the VGM. Power supply voltages must measure within +/-5% under load. Your power supply must be FCC approved.

NOTICE: MONITOR TYPE. This kit isn’t compatible with X-Y monitors. Suitable monitors have horizontally mounted CRTs and raster electronics. Only use a monitor with inputs for RGB video and composite, positive or negative sync.

NOTICE: COIN MECHANISMS. Clean your VGM’s coin mechanisms. Also test coin mechanisms with appropriate currency. Servicing these mechanisms is crucial to your VGM'’s earning potential.

NOTICE: COIN METERS. This kit doesn’t include coin meters. For your convenience, the factory provides meter wiring information. You may use salvaged meters if they operate satisfactorily.

NOTICE: 2-PLAYER CONTROL PANELS. You can use this kit to convert VGMs with 2-player control panels. A DIP-switch setting allows two-player operation. See DIP SWITCH TESTS in chapters 3 and 4.

Assembly 1-3

Page 6

PRODUCT SPECIFICATIONS Equipment Characteristics Video Display Monitor « Standard or medium resolution, RGB « Composite, positive or negative sync DIP switch U12-2 sets resolution « SIO Jumper J2 sets sync polarity

VGM Characteristics Player Variables « 1 to 4 players per game « High Score Recognition Audio System Digital Stereo Sound for 2 Coaxial, Full-Range Speakers

Operator Variables Coinage, Game Options, Difficulty, Volume, Audits, Currency Acceptors « 4 Mechanical Coin Switch Inputs Dollar Bill Validator Input ¢ Electronic Coin Acceptor Input

Diagnostics, Audits, Adjustments

  • Automatic, Power-Up Self-Test « Manual, Multi-Level Menu System Parental Advisory Disclosure: “Suitable Statistics for all Ages”

vr) 5 NOTICE: FCC COMPLIANCE. Installation of this kit into any existing product does not j guarantee compliance with FCC requirements. You are solely responsible for FCC

  • compliance for installations in other products. You must remove any existing FCC compliance label. Don’t install a new label on the converted product until you have verified FCC compliance.

INSPECT KIT 15909 Kit 15909 includes joysticks, buttons and cables to convert a player control panel. Unpack the materials from the carton and check for obvious signs of damage. Use this checklist to be sure the kit is complete. You must supply the remainder of the materials required for this conversion. Item Part # Qty Item Part # Qty ARTWORK COMPONENTS, MAJOR

O Artwork, Backlit Marquee31-35861Q Board, Auxiliary Adapter04-126521
Q Decal, Bottom Bezel Instrs31-34841Q Board, CPUA-237021
Q Decal, Cabinet Side Panel31-34762__|Q Ba, I-40 Joystick Adapter04-110891
Q Decal, NBA Hologram31-17681Q Board, Sound /OA-237041
Q Decal, Player Panel Add-Ons_|31-3481.11Q Bracket, Hard Drive01-150291
Q Decal, Player Panel Hsg31-3479-12__|Q Drive, Hard (Assy)A-237031
Q Decal, Player Pni Hsg-Front31-3479-31O Electronics (w / Video PCB) | A-232051
Q Decal, Player Pnl Wallpaper31-3480.11Q JoystickA-21939-14
Q Decal, Side Panel Logo31-35872_| DOCUMENTS
Q Decal, Top Bezel Instructions | 31-34831OQ Card, VGM Registration16-106501
QO Header, Cardboard31-3482.11Q Label, Epilepsy Warning16-9922.11
BUTTONSQ Label, FBI Warning16-8587-8251
Q Button, Blue, Long Shaft20-10209-34Q Manual, Kit16-15909-1011
Q Button, Orange, Long Shaft20-10209-74 | Q Sheet, Caution, Elec Dev16-100771
Q Button, Red, Long Shaft20-10209-14 | Q Template, Player panel16-108301
Q Button, White, Long Shaft20-10209-24MISCELLANEOUS
Q Bead, 1-1/4” Ferrite5556-13956-001
CABLESOQ Cage, EMI04-126551
Q Cable, Fan and DiskH-22900.21Clamp, 14” Cable03-7655-46
Q Cable, 20-Pin Ribbon5795-10937-09 | 1OQ Container, Hard Drive Ship | 08-80681
Q Cable, 40-Pin Ribbon5795-16308-121QO Cover, Plastic Ctl Panel03-99611
OQ Cable, Pod ExtensionH-229481OQ Grommet, 7” PlasticRM-37-111
QO Cable, Shielded Video20-104931Q Spacer, %4” PCB Mounting03-8338-16
@ Harness, Player panelH-227851_|O Spacer, Wood11-12744
Q Harness, Main Wire (JAMMA) | H-232081Q Wrench, T-20, Tamper-Res | 20-96201

Assembly 1-4

Page 7

ROX TOP

/-CARTON PAD DOCUMENTS J

ARTWORK.

INTROL

04-1 1089 [148 BOARD ASSEMBLY /. 04-124043 1 ff ELEC. PLATE

Aziose1 \ 49—WAN

~—FOAM BLOCK H-23208, fe ) MAIN. HARNESS.

111274 WOOD SPACERS \

//ASSEMALIES INNER TRAY DIVIDER

PACKAGING DETAILS FOR KIT 15909 (NO PLAYER CONTROL PANEL)

NOTICE: PLAYER CONTROL PANEL. Kit 15909 doesn’t include a player control panel. Instead, you must convert or build a player panel. Midway Games offers a plugand-play panel kit, including the housing. Your kit 15909 is 100 percent compatible with the optional player panel. If you want to order the optional panel, ask for kit 45494.

Assembly 1-5

Page 8

YOU’LL NEED THESE TOOLS AND SUPPLIES

Q_Black, semi-gloss paintQ ~~ 180 grit sandpaper or electrical sanderQ~Razor knife
QElectric drill and wood bit setQ~Wood filler (putty, board, etc.)QSqueegee or soft sponge
Q~ScrewdriversQElectrical tapeQ_Soldering iron and solder
QLiquid Soap (dish detergent)Q~Small screw assortmentQ~Wire cutters
Q~Grease pencil or markerQ ~~ Nut drivers or socket wrench setQ > Pliers

Qa Hole saw or equivalent

PUSH BUTTON

04-10849-1__ JOYSTICK KNOB, BLACK” ~~

—~__ 03-9656 COVER SLIDE

44-4274

17-1129 CENTERING MMET

4108-01219- #8 x 11/ PUSHBUTTON ASSEMBLY 03-8411 Ls

03-9722 STOP SPACER

___ 20-8712-25 "E” RING 1/4”

04-11135 OPTO BOARD

03-8419 SLIDE CARRIAGI BLITZ 2000 PUSHBUTTON TABLE ‘SHOWTIME PUSHBUTTON TABLE

oS 03-8412.1-3,

0—10209-7 1-5/4 FH PH PLASTITE i i

IN 4108-01211-28 #8-10 x

JOYSTICK ASSEMBLY

Assembly 1-6

Page 9

CONVERTING A TYPICAL VIDEO GAME CABINET

Beer ARE THE CABINET Verify operation of the old VGM before making changes to the cabinet. Pay special attention to components that you will reuse. (Power supply, video monitor, currency acceptors, wiring harnesses, cabinet locks, lighted marquee, etc.)

  • Switch off power to the VGM. Disconnect the line cord from the AC power. Clear the work area. Cover or protect non-wood items. (Marquee, monitor, coin door, brackets, line cord, etc.)
  • Remove old decals and artwork from the cabinet sides. Clean off glue residue. Fill gouges, unused holes, etc. with quick-hardening wood putty. Sand smooth and remove dust.
  • Evenly cover the entire cabinet with black paint. Allow the paint to dry completely before continuing.
  • Pencil a line roughly at the top of the previous graphic. Lightly moisten the cabinet with soapy water. Remove the backing and apply the decal. Start at the top and work down. Working outward from the center of the decal, smooth down the decal. Take care to squeeze out air bubbles. If you can’t remove a bubble, pop it with a knife or pin. Allow at least 12 hours for the adhesive in the decal to set.

[]6. Remove the backlit marquee artwork from the old marquee on the VGM cabinet. Check the fluorescent tube. If you find cracks or darkened ends, replace the tube. Clean the inside of the marquee. Use the old marquee artwork as a guide, and trim the new artwork to size. Deburr the Assembly 1-7

Page 10

[]7.

[]8.

[]9.

} 10. edges of the new marquee artwork. Crease the new artwork as necessary to match the shape of the old artwork. Clean the new marquee artwork and the marquee glass. Install the new artwork on the VGM.

Remove the viewing glass and set it in a safe place. Clean the CRT and monitor bezel. Locate the player moves and game-play instruction decals. Apply them to the top and bottom-front of the monitor bezel. Find the epilepsy warning label. Place this label on the top-front of the monitor bezel. Be sure that decals and labels don’t obstruct the viewing area Don't reinstall the viewing glass yet.

Remove and save the screws at the top and sides of the rear door. Unlock the rear door, and then lift it off of the cabinet and set it aside. Cover the VGM electronics. Use a vacuum cleaner to remove dirt or debris from inside the cabinet.

Compare your player control panel to the player panel template. If the player panel and template match, then skip to the next step. Otherwise, proceed with the rest of this step. Locate the player panel latches or fasteners. Free the player panel from its operating position. Separate the control panel’s earth ground (green) wiring from other control panel wiring. Cut cable ties as necessary to achieve this separation. Leave the earth ground (green) wiring in place. Disconnect and remove the remaining old wiring from the CPU Board and player controls. Remove the player panel and housing from the VGM cabinet. Save the mounting brackets and hardware for reinstallation later.

Some cabinets have speakers on the player panel or other removable pieces of the cabinet. If you must disconnect speaker harnesses, mark the polarity and functions of the wires. Incorrectly phased speakers can cause weak low frequencies or a thin, hollow sound quality.

NOTICE: FCC COMPLIANCE. Installation of this kit into any existing product does not guarantee compliance with FCC requirements. You are solely responsible for FCC compliance for installations in other products. You must remove any existing FCC compliance label. Don’t install a new label on the converted product until you have verified FCC compliance.

}11.

} 12. 31-3482.1

Unfold the cardboard marquee header from your kit. Make sure that the triangular brace supports the middle of the marquee.

Install the marquee header on top of the marquee. You must supply the four wood screws necessary for fastening down the marquee.

Assembly 1-8

Page 11

NBA SHOWTIME

PLAYER PANEL BUTTONS

31-3586 BACKLIT MARQUEE

31-3587

  • LOGO DECAL D

IN —7

31-3476 a L DECAL

31-1768 NBA HOLOGRAM

GOLD

TYPICAL DECAL MOUNTING DETAILS

Assembly 1-9 31-3587 D L— 31-3476 PANEL

Page 12

INSTALL PLAYER CONTROLS

NOTICE: This isn’t an actual-size drawing. Use the template to help you position and drill mounting holes. Don’t attempt to substitute this drawing for the template.

+031 18.50°.909

(]1.

(]2.

[]3.

[] 4. #031 b 40.754 031 4

16-10830

PLAYER PANEL TEMPLATE 16-10830

If you’re assembling both kit 15909 and optional player panel 45494, skip to Step 19. If you're assembling just kit 15909, proceed with the next step.

Locate and unfold the player panel template. Temporarily stack newspapers, books, magazines, etc., on the template. The weight will flatten the template sufficiently for use.

If necessary, remove buttons, joysticks and T-nuts from the old player panel and cabinet front. Remove the panel covering and artwork from the previous game. Remove and save hinges or mounting brackets.

If necessary, fill the old player panel holes with wood, putty, glue, etc. Allow adequate time for materials to dry. Sand or file the player panel to a flat surface on both sides.

31-3480.

\ 3134798 \

Assembly 1-10

Page 13

(117.

[] 18.

[] 19.

(120. 10.

11.

12.

13.

14.

15.

16. Place the player panel face down on top of the clear plastic cover. Center the player panel. Mark the outside shape of the panel on the cover. Also mark hole locations. Remove the player panel and set it aside. Cut and deburr holes for player panel buttons. Trim the cover to panel shape.

Lightly moisten the cabinet with soapy water. Remove the backing from the wallpaper decal. Apply the decal to the player panel. Start at the top and work down. After you've positioned the decal, smooth it outwards. Take care to squeeze out air bubbles. If you can’t remove a bubble, pop it with a knife or pin. Then smooth the bubble down. Allow the decal adhesive to set.

Use a sharp knife to trim edges and cut holes for player panel buttons. Position control decals next to the appropriate hole locations. Allow the decal adhesive to set.

Install the NBA hologram decal on the player panel.

Install the plastic cover over the decals and panel. Attach the cover and deburr the edges. Group player controls by color (orange, red, blue and white). Joysticks are black. You must disassemble controls for panel mounting.

Separate the switch from the orange PLAYER 1 START (left START) button. Bend the large prong away from the switch just enough to slide the switch off the housing. Unscrew the nut from the housing. Insert the button housing through its hole from the player panel's front. Screw the nut finger-tight onto the switch housing from the panel back. Rotate the housing so that switch terminals face the panel center. Tighten nuts firmly. Snap the switch back onto the housing.

Repeat the previous step with the other three start buttons.

Consult this chapter's illustration Player Panel Buttons. Install the other buttons.

Tighten the pushbutton nuts firmly. Replace player panel components and hardware that you removed earlier.

Measure the thickness of the player panel. If it is less than % inch (13 mm), use wooden spacers to recess the joysticks below the surface. Thicker player panels don’t require wooden spacers.

Install a carriage bolt in each small hole near each joystick opening. If the player panel is thin, place wood spacers over the carriage bolts. The spacers correct joystick-mounting depth.

Invert one joystick. Remove the "E"-ring from the shaft. Remove the handle and plastic ring (large washer) from the joystick base. The bushings must remain in the base. The top of the joystick base fits against the bottom of the player panel (or spacer, if used). Orient the connector toward the START buttons. Align mounting holes. Attach the base to the player panel bottom. Slide the plastic ring around the shaft so that the rough side is beside the knob handle. Slide the shaft through the player panel and base. Replace the "E"-ring. Repeat this step for the remaining joysticks.

Locate the I-40 Joystick Interface Board. Insert a plastic spacer into the bottom of a mounting hole. Press the spacer to seat it fully. Repeat this procedure until all spacers attach to the board.

Place the I-40 Interface Board inside the player panel housing. See the housing drawing. Position the I-40 Board near the housing’s right side. Assure that controls don’t hit components when you open and close the panel. Leave space above and beside board connectors for mating connectors. Mount the I-40 Board with a screw through each plastic spacer.

The completed player panel should now resemble the illustration below. Install the modified panel housing onto the cabinet with the original mounting hardware. Firmly tighten fasteners.

Install the side and front player panel decals onto the player panel housing. Assembly 1-11

Page 14

A21939-1 CONTROL PANEL 49 WAY JOYSTICK ASSEMBLY \_ 20-10209-1 PUSH BUTTON PLAYER RED

CONTROL PANEL q LU 20-10209-2 > pus BUTTON WHITE

20-10209-3 PUSH BUTTON BLUE

TYPICAL MODIFIED PLAYER PANEL.

SCREENED MARQUEE——

FLUORESCENT BULB

MARQUEE GLASS ae

SPEAKER GRILL

VIDEO MONITOR ——

  • GLASS COVER

CONTROL PANEL ASSEMBLY (SEE DETAIL DR,

7 MONITOR BEZEL

COIN DOOR (SEE APPLICATION CHART)

H_ DOOR——

“— CONTROL PANEL

—— LEVELER ADJUSTER

TYPICAL COMPLETED CABINET

Assembly 1-12

Page 15

INSTALL ELECTRONICS TRAY COMPONENTS

CAUTION: Board set electronic components are static sensitive. Prepare an anti-static work area. Ground yourself before removing circuit boards from their protective shipping materials.
WARNING: Don’t connect cables to the circuit boards or power supply when the power is on. Otherwise, you'll damage VGM electronics and void your warranty.
CAUTION: Hard disk drives are fragile. Don’t stack or drop hard disk drives.

NOTICE: If your monitor requires positive sync, remove jumper J2 on the SIO Board.

  • Switch off power and disconnect the line cord from AC line voltage. Disconnect cables from the VGM's printed circuit boards. Remove the old printed circuit boards. If your VGM includes a disk drive or drive mounting plates, remove them. Store these items in anti-static packaging from new components.
  • You can attach the new electronics directly to a cabinet wall or to a separate panel. If the cabinet doesn’t have a suitable surface, install a wood piece approximately 8 inches (20 cm) from the rear door.
  • Unpack the Electronics Tray and place it on a flat work surface. Take note of the Banshee Video Board, which is bolted to the Electronics Tray. The Banshee Video Board is a small, rectangular circuit card. You'll notice a steel header bracket at one of the Video Board’s short ends.
  • Unpack the three, unmounted circuit boards and position them over the Electronics Tray.
  • Find the CPU Board. The CPU Board is a roughly square board, and has a seven-segment LED display. In the center of the CPU Board are two large, heat-sinked ICs. Position the CPU Board’s 15-pin connector beside the Video Board’s header bracket. Then plug the CPU Board into the Banshee Video Board.
  • Find the Sound I/O Board. The Sound I/O Board is a roughly square board, with a JAMMA connector on one side. This board also includes the VGM’s DIP-switch banks. Plug the Sound I/O Board into the CPU Board.
  • Align circuit board mounting holes with standoff posts on the Electronics Tray. Mount the circuit boards to standoffs with 8-32 Phillips pan head screws.
  • Find the Auxiliary Output Adapter Board. This is a small, rectangular board, with two connectors. It doesn’t plug into any of the other boards. Notice the ribbon connector on the side of the Auxiliary Output Adapter Board. Position this connector close to the Sound I/O Board. Screw the Auxiliary Output Adapter Board to standoff posts on the Electronics Tray.
  • The factory installed the fans for you. They reside beneath the board set and hard drive. If you mounted the boards vertically, the fans should blow upward, across the electronics. You'll want to check the airflow later. (For now, check fan markings that indicate airflow direction.)

Assembly 1-13

Page 16

03-7655-4 5795-10937-09

04-12652

03-7655-4 03-7655-4

5795-16308-12 _ 04-12404.3 ISK DRIV

20-10493 5556-13956-00 SUED VIDEO CAB 01-14923 _

20-10516 *

TYPICAL ELECTRONICS LAYOUT

WIRE THE CIRCUIT BOARDS

NOTICE: You must install the Main (JAMMA) Wiring Harness supplied with this conversion kit. This VGM’s 49-way joysticks require wires and circuits not found in earlier VGMs. If the connectors in your cabinet don’t fit onto the CPU Board or wire colors don’t match the JAMMA Chart, contact your authorized distributor for assistance.

CAUTION: Insulate unused wires within the JAMMA cable, especially red, yellow, orange and black power wires. Secure unused connectors away from the CPU Board and its cover.
CAUTION: ATTACH CONNECTORS PROPERLY. Be sure that printed circuit board (PCB) connectors mate properly. If connectors don’t slip on easily, don’t force them. A reversed connector may damage your VGM and void the warranty. Connector keys allow a connector to fit only one set of pins on a board.

]1. Connect the shielded video cable between Video Board jack J4 and CPU Board plug P4. Your video monitor requires either positive or negative sync. If necessary, add or remove the video sync jumper at SIO Board jumper block J2. The default mode is positive sync (no jumper between pins 1 and 2). For negative sync, jump pins 1 and 2. Assembly 1-14

Page 17
  • Locate disk drive power cable H-22900.2. (This cable has separate wires and plastic connectors at each end). Attach the power cable to SIO connector P3 (near a large heatsink). Mate the plug and jack. Press them firmly to seat contacts. The connector is keyed. Don’t use excessive force.
  • The disk drive power cable includes three plugs for the fans. Connect these plugs to the fans.
  • Secure hard disk drive and fan cables with three cable clamps from the kit. Attach the cable clamps to standoffs at three corners of the SIO Board. Use the board’s mounting screws to fasten the clamps to the standoffs: Position the first clamp near the SIO Board’s large heatsink. Position the second clamp directly across from the first, near the Auxiliary Adapter Board. Position the third clamp near the hard drive.
  • Locate the hard drive data cable, a ribbon cable. Orient the data cable connector over CPU Board plug P5. Align the connector’s striped edge with Pin 1, near the video connector. (The stripe may be red, blue or another color.) Mate the connector halves. Press them firmly to seat contacts.
  • Connect the Main Harness to the SIO Board edge (JAMMA). This cable has wires for the coin door, control buttons, I-40 Joystick Interface Board, speakers, video monitor, power supply, and so forth. Insulate and secure all extra wires (unused slam tilt switch, coin meter, etc.).
  • Search through the Main Harness for the Player 4 and Player 3 cables. Player 4 has gray wires with stripes. Player 3 has blue wires with colored stripes. Connect Player 3’s plug to SIO Board jack P14, and Player 4’s plug to P7.
  • Find the coin door power connector. (Look for the black, red and orange wire bundle.) Attach this connector to plug P23 on the SIO Board.
  • Search through the Main Harness for the six-pin monitor connector. Plug this into your monitor.
  • Connect the Main Harness to the Aux Out Adapter Board at connector P1.
  • Connect the 20-pin ribbon cable to the Aux Out Adapter Board at jack P1. Connect the other end of this ribbon cable to SIO Board at jack P15.

MOUNT THE ELECTRONICS TRAY

  • Set the electronics against the wood panel. Use the tray as a template to mark mounting hole locations. (If you plan to mount the electronics vertically: Orient the Electronics Tray so that its long edges are vertical and large heatsinks are at the top.)
  • If necessary, drill pilot holes for mounting screws. Use sheet metal screws to secure the Electronics Tray to the cabinet. Attach the tray with only four corner screws. Don’t use excessive force.
  • | Remove the hard drive from its package. Locate the hard drive mounting bracket. Set the drive in the mounting bracket. Align screw holes and install the 6-32 screws with spring washers.
  • Orient the drive and drive mounting bracket over threaded studs on the Electronics Tray. Align the holes. Attach the bracket with 8-32 KEPS® nuts.
  • Temporarily hold the perforated metal cover over the electronics. Be certain that cover mounting holes are accessible. Relocate the plate if necessary. Don’t install the metal cover yet.

Assembly 1-15

Page 18

(16.

[]7. Locate the data and power connectors on the hard drive. Connect the free end of the hard drive power cable to the disk drive. Mate the plug and jack. Press them firmly to seat contacts. Don’t use excessive force.

Position the striped edge of the hard drive data cable by the power cable. Attach the cable to the drive’s data connector. The data connector is keyed. Don’t use excessive force.

WIRE THE CABINET

Kit 15909, Without Optional Player Panel 45494...

NOTICE: This player panel uses 49-way joysticks and an I-40 Joystick Interface Board (input-multiplexer circuit). The VGM requires additional wiring harnesses. These items must be field installed to customize the unit for each kit.

Locate cable H-22785. This cable includes a fuse for protection of the Joystick Interface that mounts in the player panel housing. This cable must be mounted in the player panel housing. Remove the fuse from the fuse holder and retain it for reuse.

Open the player panel. Place the fuse holder beside the wall of the player panel housing. Attach the fuse holder with a #6 short sheet metal screw (not supplied). Reinstall the fuse in the holder.

Connect cable H-22785 between the I-40 Joystick Interface Board and each joystick. Player 1 wire colors are mostly white, Player 2 wires are violet, Player 3 are blue, and Player four are gray. The 1-40 connectors are User 0 (Player 1), User 1 (Player 2), User 2 (Player 3), and User 3 (Player 4). This VGM doesn’t use the User 4 connector. Consult the Cabinet Wiring Diagram, and connect the cable wires to the switches. Secure wiring with a cable clamp and cable ties.

Connect the Common terminal of each button on the panel with a black wire. Join this wire with the black wire from the cable. Connect the Normally Open terminals to each of the switch wires.

All Kits...

CAUTION: Prevent electrical fires and power supply damage! When attaching JAMMA pigtails to the power supply, maintain fusing from the original VGM wiring. If a line was fused before, then the new line must have a fuse, too.

See the Cabinet Wiring Diagram. Connect your power supply to the pigtail leads from the Main (JAMMA) Harness. Red wires connect to +5 volts DC. Yellow wires connect to -5 volts DC. Orange wires connect to +12 volts DC. Black wires connect to ground. If necessary, solder the appropriate connector onto the Main Harness, or design your own adapter. Thoroughly insulate soldered or pigtail connections.

Connect cabinet speakers to the pigtail leads from the Main Harness. Red-gray and brown-gray wires connect to the left speaker. Red-white and brown-white wires connect to the right speaker. To eliminate serious distortion, be sure to phase the speakers properly. With either speaker, connect the red wire to the speaker's positive phase terminal. On many speakers, a dot marks this terminal. To test for positive phase, connect a 1.5-volt battery to the speaker and observe the cone. If the cone moves inward, reverse the battery leads. When the cone moves outward, the positive battery lead connects to the positive phase terminal. Mark this terminal with a dot.

Assembly 1-16

Page 19

(17.

10.

11. Locate the square, split ferrite bead. The factory has installed one ferrite bead around DC power conductors (solid color heavy gauge wires with pin numbers 1-6 or A-F). A second bead encircles player panel conductors (striped color lighter gauge wires). Install the remaining ferrite beads on the video monitor cable and power supply wires. The video cable bead should trap a loop of cable. Place all beads as close to the JAMMA connector as possible. Then close and lock each bead. Assure that no wires are pinched or caught in the latches. LOOP VIDEO CABLE THROUGH BEAD

Locate the central power ground point for the cabinet. (Ground wires are usually green. Some may have a yellow stripe.) Assure that the previously installed ground wire from the controller port still connects to the same central point. Reconnect ground wires that you loosened or removed in previous steps (monitor, player panel, coin door, etc.).

Find the electronics cover. Install plastic grommet RM-37-11 over the aperture where cables pass through the cover. This grommet part is a tough, plastic sleeve. It protects your fingers and your cables from the cover’s sharp, metal edge.

Locate the sheet metal screws from the kit. If necessary, drill pilot holes for the screws. Install the electronics cover. Insert a screw in every mounting hole. Fasten the Electronics Tray to the cabinet. Tighten the screws firmly. Take care not to pinch wires.

Connect your coin door switches to the pigtail leads from the Main Harness. If your cabinet doesn’t include diagnostic switches, you may add them now. (These momentary switches speed up routine service calls.) Refer to the cabinet wiring diagram in Chapter Five. Thoroughly insulate soldered or pigtail connections.

NOTICE: You can order the diagnostic switch bracket and switches as Midway part number A-19542-1.

NOTICE: IF YOU’RE INSTALLING A BILL VALIDATOR, set the validator for 1 pulse per dollar. Also adjust the pulse width setting. The validator must generate pulses with these timing parameters: 50ms on (minimum) and 50ms off (minimum).

Assembly 1-17

Page 20

CHECK YOUR CABLING JOB

[]1.

(]2. Carefully inspect cables between peripherals and the board set. The main wiring harness edge connector (JAMMA) attaches to the SIO Board.

The hard drive data (ribbon) cable connects the hard drive to CPU Board jack P5. Be sure that you've also connected the hard drive power connector to power cable H-22900.2. The other end of this cable should connect to the SIO Board at P3.

CABLE BLOCK DIAGRAM

Assembly 1-18

Page 21

[]3.

[] 4.

[] 5.

(16.

(17.

(18. The Player 3 connector (blue wires) attaches to the SIO Board at P14. The Player 4 connector (gray wires) attaches to the SIO Board at P7. This connector links SIO circuits to the I-40 Joystick Interface Board.

Open the player control panel and locate player panel cable H-22785. This cable connects to the joysticks, switches, fuses, and !-40 adapter. Connectors designated Player 1 (mostly white wire colors) and Player 2 (violet) mate with the same color cables from the main harness. Player 3 (blue) and Player 4 (gray) connectors mate with the same color cables from the main harness. Power connectors (red and black) from player panel fuses mate with the same color cable from the main harness.

Check wiring to the Auxiliary Output Adapter Board against instructions in Wire the Cabinet. The block diagram below also depicts this wiring.

A shielded cable should join Video Board jack J4 and CPU Board plug P4.

Have you connected the monitor to the Main Harness?

Assure that you’ve reinstalled all fuses. Check that you've set DIP switches correctly (Chapter Three).

meters ee OS xe

a aace : & : < ‘ Ss <n os ee satete BH cee see 6% Sone ae SOS cee ones me secarcee seis % SE rere SS SSS mee scatts ss se EERE SORES SS os a aeseen = =< se seine SES

TYPICAL REAR VIEW OF COMPLETED CABINET Assembly 1-19

Page 22

POWER UP AND TEST THE VGM

1.

10.

11. Plug the power cord into the AC line and turn on the VGM. Circuit board indicators should illuminate.

The VGM system loads the program and begins self-diagnostics. If the system doesn’t find any errors, the system automatically enters its Attract Mode. If problems occur, check wiring and troubleshoot the machine.

Unlock and open the coin door. Press and hold the TEST MODE button until the Menu System appears on the screen.

Select MONITOR SETUP at the Diagnostics Menu. Confirm proper video display operation and adjust the monitor as necessary.

Select DISK TESTS at the Diagnostics Menu. Run all the tests in order to verify correct drive operation.

Select SWITCH TESTS at the Diagnostics Menu. Check to be sure that all control switches work.

Select DIP-SWITCH TESTS at the Diagnostics Menu. Verify that all switches are set to optimum positions for this VGM.

Select SPEAKER TEST at the Diagnostics Menu. Verify operation of audio system components.

Select EXIT at the Main Menu. The system should enter Game-Over Mode. Open the coin door and press the SERVICE CREDITS button to allow game play. Choose a joystick and press the START button to begin play. Listen to the audio while playing the game. Note sound irregularities (phase problems, no low frequencies, mono audio from stereo speakers, etc.). Check the wiring harness for internal shorts or strapped connections.

Close and lock the coin door. Replace the rear cabinet door. Allow the system to operate for several hours before attempting any game changes.

After you confirm proper operation, submit the VGM for FCC or other agency approval.

CAUTION: You are solely responsible, and Midway has no responsibility for FCC compliance of installed kits. Don’t install an FCC compliance label on the product until the FCC acknowledges compliance.

Assembly 1-20

Page 23

NBA SHOWTIME Gotp EDITION/ NFL Bi1z72000 Goin EDITion

CONVERSION KIT

CHAPTER

TWO

OPERATION

NOTICE: The term VGM refers to the video game machine.

Operation 2-1

Page 24

VIDEO GAME MACHINE (VGM) OPERATION

STARTING UP

Whenever you turn on the machine or restore power, the system executes boot ROM code. The boot ROM contains self-diagnostic tests. These tests automatically verify and report the condition of the disk drive and other hardware. The screen is blank during these tests. If the hardware fails a test, the system displays an error message. The message appears for 30 seconds or until someone presses a button.

« If nobody presses a button, the system quickly completes tests, and then loads game software.

« To skip boot ROM tests and activate the Menu System, press and hold the TEST MODE button. You'll find this button behind the coin door.

Having passed power-up tests, the VGM computer enters Attract Mode. Attract Mode consists of typical game scenes and sounds, alternating with high scores. Attract Mode continues until game play commences.

Players insert currency or tokens to start the game. Pressing a START determines which player receives the credit. The VGM computer asks the players which game that they want to play: NBA Showtime Gold Edition or NFL Blitz 2000 Gold Edition. Players request one or the other via player panel controls. Then players select a team. The VGM computer associates one team with the Player—1 and Player-2 joysticks. The Player—3 and Player-4 joysticks assume control of the opposing team. Play begins after a countdown period. Play progresses like a real-life football or basketball game. At Game-Over Mode, players may choose to begin again. If players choose not to continue, then the VGM computer returns to Attract Mode.

GAME RULES FOR NFL BLITZ 2000 GOLD EDITION

INSTRUCTIONS Play instructions appear on the information panel over and under the video monitor.

ONE TO FOUR PLAYERS Players may enter their names for future reference. Then they select teams and run the first play. Players may choose an offensive or defensive play. Additional game information appears on the screen as needed. Team statistics appear at the end of each quarter.

CONTROLLING CHARACTERS The joystick and action buttons control characters on the field. The joysticks respond to different amounts of deflection as well as direction.

GAME ACTION Standard league football rules apply, with two exceptions: First downs require 30 yards, and teams only have seven active players. Game adjustment settings determine game length and speed.

The player view of the action changes automatically whenever a better camera angle becomes available. The game sounds include announcer comments and crowd noises.

SCORING Touchdowns and goals score points, just as in real football games.

PLAY SELECTION FOR NFL BLITZ 2000 GOLD EDITION STANDARD PLAYS The player may select any of the offensive or defensive plays in the game. Players can choose from pages of standard plays loaded into the game. Use the indicated pushbuttons to view and select any play. Operation 2-2

Page 25

CUSTOM PLAYS Players may choose to create their own offensive plays rather than depend on the standard plays in the game. Players can design and name their plays using the CREATE PLAY feature, then store these plays for future use. These custom plays become available on an additional page of game plays.

PLAYER CONTROLS FOR NFL BLITZ 2000 GOLD EDITION The player controls are used to maneuver the team members and attack or defend against adversaries.

NOTICE: Use joystick and button combinations to discover secret moves.

« START. This button allows players to begin or continue play. Use PLAYER 1 START and PLAYER 2 START to begin a two-player game. START has no game action or service function.

« JUMP / TACKLE. This button lifts the offensive team member up or causes the defensive player to tackle opponents. Use this same button to create plays or select menu items during service.

« PASS / CHANGE PLAYER. This button activates offensive throws. The defense move switches active control to another teammate. Use this same button to create plays or select menu items during service.

« TURBO. The TURBO button gives any active character an extra burst of power or speed. Use this same button to create plays or select menu items during service.

« JOYSTICK. Each player has a joystick to control the movements of one on-screen character at a time. Use the joystick to create plays or select menu items during service.

RECOMMENDED PLAYER CONTROL LOCATIONS

Operation 2-3

Page 26

GAME RULES FOR NBA SHOWTIME GOLD EDITION

INSTRUCTIONS Play instructions appear on the information panel over and under the video monitor.

ONE TO FOUR PLAYERS The player or players insert currency to start the game. Each player chooses a joystick and presses the nearest START button. Players select a team and two characters. In four-player games, each player controls one character. In games with fewer players, each player controls one character. The VGM computer controls remaining characters. The VGM computer displays team scores and statistics at the end of each quarter. Additional game information appears on screen as needed.

CONTROLLING CHARACTERS The joystick and action buttons control characters on the basketball court. The joysticks respond to different amounts of deflection as well as direction.

GAME ACTION Standard NBA basketball rules apply, except that the game only includes four active characters. Game settings determine game length and speed. The player view of the action changes automatically whenever a better camera angle becomes available. Game sounds include announcer comments and crowd noises.

SCORING The game awards points for baskets, just as in real basketball games.

PLAYER CONTROLS FOR NBA SHOWTIME GOLD EDITION

« JOYSTICK. Each player’s joystick controls the position of that player’s characters on the video screen.

« PASS/STEAL (the blue button) controls character actions on the video screen. Press PASS/STEAL to attempt to pass or steal the ball.

e SHOOT/BLOCK (the red button) controls character actions on the video screen. Press SHOOT/BLOCK to shoot or attempt to block the ball.

« START (orange buttons). Each START button allows the corresponding player to begin or continue play.

« TURBO (The white button) controls character actions on the video screen. Press TURBO to speed up the pace of a play.

GAME FEATURES OF NBA SHOWTIME GOLD EDITION

NBA Showtime is a thrilling, two-on-two basketball game with world-class realism. Each player selects an NBA team, and then chooses a favorite character. Players can also create their own players. If fewer than four players are in the game, the computer operates the remaining characters.

Operation 2-4

Page 27

The red team comprises players 1 and 2. Players 3 and 4 make up the challenging, blue team. The red and blue teams square off for the jump and the action begins. Run the ball down court! A steal! Dribble up court! A snap shot! The breathless announcer describes every pass, every shot, every block, every move!

After each quarter, new players can join the fun. Players can also switch to different characters. When the game concludes, team and individual scores appear on the screen. Top scorers may enter their initials or names with a joystick. NBA Showtime displays these initials in a high score table.

DIAGNOSTIC CONTROL SWITCH LOCATIONS (TYPICAL INSTALLATION)

OPERATOR CONTROLS

CABINET CONTROLS

  • The DIP Switches set some system variables. You can set other variables with diagnostic control switches.

¢ The Monitor Remote Control Board allows you to adjust the video display for optimum viewing.

  • The POWER Switch turns off the video game machine, but does not reset game variables.

DIAGNOSTIC CONTROL SWITCHES,

¢ The SERVICE CREDITS Button allots credits without changing the game's bookkeeping total. SERVICE CREDITS has no function in the Menu System.

Operation 2-5

Page 28

« The TEST MODE Button causes the VGM to enter the service Menu System. Press the TEST MODE button briefly to run automatic tests. To make game adjustments, press and hold TEST MODE until the Main Menu appears. Within the Menu System, TEST MODE assumes another function. There, it selects a menu line item and calls up the item’s submenu. The screen displays this submenu.

« VOLUME DOWN and VOLUME UP Buttons set game sound levels. To make minor volume changes, press either button briefly. To make major changes, press and hold a button. In the Menu System, VOLUME UP moves the item highlight bar up the menu. VOLUME DOWN moves the item highlight bar downward.

( »)) NOTICE: You must adjust Attract Mode volume independently of Game Mode volume. Ca For greater profits, increase volume levels to draw attention to this game.

MAINTENANCE

¢ Cabinet Use only non-abrasive cleaners to avoid damaging game graphics. Apply cleaner to a clean cloth or sponge. Wipe the screen clean with this cloth or sponge. Do not apply cleaner directly on the cabinet!

¢ Control Panel Dirt or debris on the joysticks or buttons can affect earnings. Apply the cleaner to a clean cloth. Use the cloth to wipe the controls. Don't apply the cleaner directly to the controls!

e Viewing Glass To clean the glass, you don’t need to switch off power to the VGM. Apply a mild glass cleaner to a clean cloth or sponge. Use this to wipe the viewing glass. Do not apply the cleaner directly on the glass! Liquid could drip down into switch or motor circuits and cause erratic VGM operation.

SERVICING Only qualified service personnel should perform maintenance and repairs. The following product guidelines apply to all VGM operators and service personnel. Notes, cautions and warnings appear throughout this manual where they apply. Read the SAFETY pages thoroughly before beginning service.

« Circuit Board Set The VGM computer uses a set of three circuit boards. The three boards include the CPU Board, I/O Board and Video Board. Switch off power to the VGM. Open the rear door. To expose the circuit boards, remove their perforated metal cover. Carefully note the orientation of the JAMMA connector and other cables. Extract the harness and hard disk drive ribbon cable from the board connectors. Remove circuit board mounting screws. Lift the circuit boards out of the cabinet and set them in a safe place. Use anti-static packaging from new parts to store boards that you won't reinstall.

Operation 2-6

Page 29
CAUTION: Circuit board edge connectors are fragile. Take care when separating boards in the board set. Never jam the board connectors together. Never plug them together on an extreme angle. If necessary, carefully straighten bent pins with a small, grounded flat blade screwdriver. Also, don’t touch exposed foil on printed circuit boards. Skin oils are corrosive.

NOTICE: Avoid damage to VGM electronics! Turn off VGM power before servicing circuit boards or any electronic assembly. Never “hot plug” circuit boards.

Coin Mechanism Switch off power to the VGM. Unlock the coin door and swing it open. To clean or replace a coin mechanism, unlatch and remove it. After reinstallation, ensure that the mechanism seats fully its bracket. Close and lock the release latch, and then close the door. Turn on the VGM and change the mechanism setup. Test known good and bad coins to verify operation.

Coin Meter Switch off power to the VGM. Unlock the cash door and swing it open. The coin meter mounts to a metal plate at the bottom the cash vault. Record the meter count before testing or replacement. Remove the plate’s four mounting screws, and then remove the plate.

Disconnect the meter wiring harness at the connectors. Remove front screws and slide the meter out. Assure that a protective diode connects across the replacement meter’s terminals. The diode prevents driver circuit damage.

Hard Disk Drive Switch off power to the VGM. Unlock and remove the rear cabinet door. Remove the perforated metal cover over the VGM electronics. Disconnect the DC power cable from the hard disk drive. Unplug the ribbon cable from the hard drive. Don’t disconnect the cables from the CPU Board. Loosen the drive mounting screws and lift the drive out of its mounting bracket. Remove the screws. Save them for reuse in future hard drive installations. When returning a hard drive to your distributor, pack it in an anti-static bag. Box the drive in approved shipping container 08-8068.

NOTICE: Hard disk drives are very fragile! Handle them with care. Do not stack or drop hard disk drives. Keep disk drives away from magnets, heat and vibration.

Joysticks Switch off power to the VGM. Open the player control panel. Mark and disconnect the wiring harness from a joystick. To separate the joystick from the player panel, first remove the joystick shaft. An Ering secures the shaft. Disengage this E-ring with a small, flatblade screwdriver. Grasp the joystick knob. Extract the stick from the assembly. Then remove 8-32 KEPS® nuts from the corners of the joystick base. Retain fasteners for reassembly.

Operation 2-7

Page 30

Memory

ry CAUTION: Static electricity builds up on your body. This static can damage or

destroy sensitive VGM circuits. BEFORE touching or handling electronic \V assemblies, discharge static electricity by touching the electronics mounting plate.

NOTICE: CPU Board and SI/O Board chips don’t face same direction. When mounting chips on either board, refer only to chips on the same board for reference. Never use chips another board for reference.

ROM (Read Only Memory) circuits contain computer operating instructions for this VGM. Switch off power to the VGM. Unlock and remove the rear door. Remove the perforated metal cover. Note the ROM chip position. Remove the device with a chip extraction tool. To reinstall a ROM chip, orient the device over its socket. Press the chip firmly to seat pins. Don’t force the chip into the socket.

Operation 2-8

Page 31

VGM ELECTRONICS

INTERNAL COMPONENTS ¢ Monitor

CAUTION: The video monitor is heavy, with most of the weight toward the front of the assembly. Support the monitor as you remove it from the cabinet.

Switch off power to the VGM. Open the control panel. Remove the viewing glass and monitor bezel. Unlock and remove the rear door. Disconnect the monitor from the wiring harness, remote adjustment board, and ground wires. Remove the fasteners that secure the monitor frame to its mounting panel. Carefully pull the monitor from the cabinet. Set the monitor in a safe place. Remove the remote adjustment board from the cabinet and reconnect it to the monitor before servicing or replacement. Clean the face of the CRT before reinstalling the monitor bezel.

Operation 2-9

Page 32

NOTES

Operation 2-10

Page 33

NBA SHOWTIME Gotp Eoirion/ NFL Bi1z2000 Gown Ebivion

CONVERSION KIT

CHAPTER

THREE

DIAGNOSTIC, AUDIT & ADJUSTMENT MENU SYSTEM

FOR NFL BLITZ 2000 GOLD EDITION GAMES

NOTICE: This manual is subject to change without notice. Midway reserves the right to make improvements in equipment as progress in engineering warrants.

NOTICE: GAME-SELECTION SWITCH. Select NBA Showtime or NFL Blitz by flipping switch 8 at DIP bank U13. Then power down and up again. The Attract Mode for the game you select will appear. The player can still play either game.

Diagnostic, Audit & Adjustment Menu System for NFL 3-1

Page 34

MENU SYSTEM

WHAT IS THE MENU SYSTEM? The game’s Menu System is a series of auditing, game adjustment and diagnostic screens. We call these screens menus, because they present options in menu-like lists. You can easily access and apply menus to optimize game performance. For instance...

« Use game audits menus to assess game performance. « Use adjustment menus to help you to customize game performance. For instance, you can restore factory default game settings. You can also calibrate player controls for accuracy. e Use diagnostic menus to verify proper equipment operation.

ACTIVATING THE MENU SYSTEM Open the coin door. Find the TEST MODE switch inside. Press TEST MODE to invoke the Menu System. The game system responds by exiting Game Mode and entering Diagnostic Mode. You can also invoke the Menu System by turning on DIP bank U12, switch 8. (To reenter Game Mode, turn off switch 8.)

AUTOMATIC TESTS In Diagnostic Mode, the Power-On Self-Test (POST) activates. This routine runs automatically. It can detect faults that cause game or Menu System malfunctions. POST usually takes less than a minute. The test doesn’t display anything. Instead, the system boot loader indicates the software revision number and serial numbers. The system boot loader also displays a sound-loading message and other useful information.

At the end of POST, the system displays the Control Functions Menu.

CONTROL FUNCTIONS MENU The Control Functions Menu is purely informational. It appears for five seconds. Then the Menu System automatically displays the Dual Game Adjustment Menu.

The Control Functions Menu introduces the menu navigation controls. The key point is that you can use either player or diagnostic controls to navigate menus. Diagnostic control switches are particularly helpful when you must troubleshoot player switches. This manual discusses the controls in more detail in this chapter’s Main Menu section. Also see the page on the menu that interests you.

STICK UP/VOLUME UP — MOVE UP

STICK DOWN/VOLUME DOWN — MOVE DOWN

STICK RIGHT — MOVE RIGHT

STICK LEFT —- MOVE LEFT

PUSH BUTTON/TEST BUTTON - SELECT

5 SECONDS TO DIAG ENTRY

CONTROL FUNCTIONS MENU

Diagnostic, Audit & Adjustment Menu System for NFL 3-2

Page 35

DUAL GAME ADJUSTMENT MENU The Dual Game Adjustment Menu is another informational, read-only menu. It appears until you choose to exit. This menu reminds you that some NFL settings also affect NBA game play. Press any button to exit to the Main Menu.

ATTENTION!

ANY CHANGES TO THE FOLLOWING ADJUSTMENTS,

UPDATE BOTH NBA AND NFL.

PRICING

FREE PLAY

VOLUME LEVEL

DISCOUNT PRICE / CREDITS

ATTRACT MODE SOUND ON / OFF

THIS ALSO INCLUDES DEFAULT ADJUSTMENTS,

AND

FULL FACTORY RESTORE FUNCTIONS.

PRESS ANY BUTTON TO EX!

DUAL GAME ADJUSTMENT MENU

MAIN MENU The Main Menu offers you access to the game machine’s test, bookkeeping and programmable features. Game audits, adjustments and diagnostics are line items on the Main Menu. Selecting an item opens its submenu. Every submenu presents various options that you may act upon.

NFL MAIN MENU

DIAGNOSTICS AUDITS ADJUSTMENTS VOLUME LEVEL ATTRACT VOLUME LEVEL UTILITIES NBA MAIN MENU EXIT TO NBA EXIT TO NFL

MAIN MENU

MENU LAYOUT Menus differ, but related information tends to occupy the same menu locations.

e The block at the top, center of each menu displays the current menu title. « Data (menu items, video signals, statistics, reports, etc.) appears in the center of the menu. « Messages (explanations, control functions, revision levels) display at the bottom of the menu.

MENU NAVIGATION CONTROLS Use any player panel joystick to highlight a desired menu item. You can only select one highlighted item at a time. To select a highlighted item, press any player panel button. Operator control buttons inside the

Diagnostic, Audit & Adjustment Menu System for NFL 3-3

Page 36

coin door serve as backup menu navigation controls. Press VOLUME UP or VOLUME DOWN buttons to highlight a menu item. Press TEST MODE to select a highlighted item.

EXIT OPTIONS To exit the NFL menus and simultaneously enter the NBA menus, choose NBA MAIN MENU. To return the game to play, highlight either EXIT TO NFL or EXIT TO NBA. Your choice determines the game that will boot. Next, press any button.

NOTICE: This manual depicts some menus as having two pages. Your video game machine may present these same menus as one-pagers. Monitor resolution affects whether a menu has a second screen.

Main Menu (continued) Diagnostics Menu

DIAGNOSTICS Select DIAGNOSTICS at the Main Menu. Diagnostic tests allow you to verify the condition of the electrical and electronic hardware in the game.

Highlight a test with any player panel joystick. Select the option with any player panel button.

DIAGNOSTICS

MONITOR SETUP.

SYSTEM INFO

SOUND SUBSYSTEM

DISK TESTS

SWITCH TESTS

DIP-SWITCH TESTS

SPEAKER TEST

EXIT

DIAGNOSTICS MENU

Diagnostic tests assist you in checking and adjusting the game’s major systems. By running diagnostics, you can gain an insight into both system hardware and game software. Periodically running diagnostics is a crucial part of maintaining game performance and player satisfaction. Sometimes you can improve game performance by running a diagnostic test and making appropriate adjustments.

Diagnostic, Audit & Adjustment Menu System for NFL 3-4

Page 37

Main Menu (continued) Diagnostics Menu (continued) Monitor Setup Menu

MONITOR SETUP Select MONITOR SETUP at the Diagnostics Menu. The Monitor Patterns routine provides test screens to verify monitor performance or make adjustments.

Highlight an option with any player panel joystick. Select the option with any player panel button.

MONITOR SETUP.

COLOR BARS

CROSSHATCH

RED SCREEN

BLUE SCREEN

GREEN SCREEN

WHITE SCREEN

BLACK SCREEN

50 PCT. GRAY SCREEN

25 PCT. GRAY SCREEN

EXIT

MONITOR SETUP MENU

Color Bars fills the screen with colored stripes. Use the color bars to help you to check or adjust monitor brightness and contrast. The color bars also expose defects in horizontal linearity. Each color bar consists of 32 intensity levels. On a properly adjusted monitor, the top 31 of these levels are visible. Each bar should appear sharp, clear and distinct from bars on either side. Incorrect adjustment can cause missing detail at the top or bottom of a bar. Bent bars indicate horizontal linearity flaws, such as pie crust, pincushion or barrel distortion. (Correct color bar colors, left to right: Red, Green, Blue, Black, White, Cyan, Yellow, Violet.) Set controls as follows: 1. Adjust BRIGHTNESS and CONTRAST to minimum. 2. Turn up BRIGHTNESS until the pixels in the black stripe begin to glow (turn dark gray). 3. Bring up the CONTRAST control until you can see 31 bars.

Crosshatch Patterns fill the screen with a grid and a series of dots. Crosshatch Patterns help you to check or adjust several monitor parameters: These include convergence, linearity, active viewing area and dynamic focus. The grid and the dots should be all white in color, with no fringes or parallel images. The lines should be straight and the dots round. For more detail on these adjustments, consult service literature from the monitor manufacturer.

Color Screen tests fill the screen with 100% of the chosen color at normal intensity. The Color Screen tests help you to check or adjust monitor intensity, black level, blanking and color purity. Each screen should be absolutely uniform from top to bottom and side to side. No retrace lines or noise should be visible. Color Screens may not hold their uniformity if the monitor degaussing circuit is defective.

White, Gray and Black Screens fill the screen with black, gray or white at various intensities. These monochrome screens help you to check or adjust monitor convergence, purity, contrast and intensity. These screens also simplify black level and color gun control settings. The screens should be uniform with no color tints or distortion. No retrace lines or noise should be visible.

If tests indicate a need for adjustment, use controls on the Monitor Remote Adjustment Board.

Diagnostic, Audit & Adjustment Menu System for NFL 3-5

Page 38

Main Menu (continued) Diagnostics Menu (continued) System Information Menu

SYSTEM INFORMATION Select SYSTEM INFO at the Diagnostics Menu. The System Information Menu provides the current version numbers of this game’s hardware and software. Use these numbers to describe the system during parts replacement, service calls, etc.

Highlight an option with any player panel joystick. Select the option with any player panel button.

SYSTEM INFORMATION

MIDWAY GAMES, INC. XXXXXXX SYSTEM

SERIAL NUMBER: XXXXXXXXX

GAME: XXXXXXXXXX

DATE OF MANUFACTURE: XX/XX/XX

PRESS ANY BUTTON TO EXIT

SYSTEM INFORMATION MENU

The System Information screen reports information, but doesn’t permit you to make changes. The Title line identifies the manufacturer of this game and the electronic board set used in this product. The Serial Number, Game and Date of Manufacture identify the game name and production run.

Diagnostic, Audit & Adjustment Menu System for NFL 3-6

Page 39

Main Menu (continued) Diagnostics Menu (continued) Sound Subsystem Menu

SOUND SUBSYSTEM TEST Select SOUND SUBSYSTEM at the Diagnostics Menu. Sound Subsystem Tests verify that audio components are connected and operate properly.

Highlight an option with any player panel joystick. Select the option with any player panel button.

SOUND SUBSYSTEM TEST

BOOT VERSION: XX.XX

SDRC VERSION: XX.XX

PORT STATUS: GOOD

CHECKSUM: XXXX

SRAM: OK

DRAM: OK

TONE STATUS: GOOD

OS VERSION: XX.XX

PRESS ANY BUTTON TO EXIT

SOUND SUBSYSTEM MENU

Version, Status, Checksum and RAM Reports are diagnostic routines. These routines analyze the digital sound circuits and can detect sound memory problems. Test results appear as numbers or messages. Sounds may also accompany some tests. Reports other than GOOD or OK indicate a problem.

Diagnostic, Audit & Adjustment Menu System for NFL 3-7

Page 40

Main Menu (continued) Diagnostics Menu (continued) Disk Tests Menu

DISK TESTS Select DISK TESTS at the Diagnostics Menu. Disk Tests allow you to verify proper operation of the hard disk drive assembly.

Highlight an option with any player panel joystick. Select the option with any player panel button.

DISK TESTS

DISK INFORMATION

SEQUENTIAL READ

SEQUENTIAL CACHE READ RANDOM READ

RANDOM CACHE READ

DATA INTEGRITY TEST

FILE SYSTEM CHECK

SURFACE SCAN

EXIT

DISK TESTS MENU

Disk Information. The Disk Information routine verifies the interface between the CPU Board Assembly and hard disk drive. The processor requests disk information. Data cannot be retrieved successfully if there is a problem.

Sequential Disk Read. This routine tries to access every bit of data in the order it is stored directly on the disk. The hard disk drive media may be defective if this routine cannot be completed successfully.

Sequential Cache Read. This routine tries to access every bit of data in the order it is stored in the temporary disk memory cache. If this test is not successful, the memory circuits may be faulty.

Random Disk Read. This routine tries to access every bit of data in no particular order directly from the disk. This test may detect problems with ability to position the drive heads accurately over the requested data.

Random Cache Read. This routine tries to access every bit of data in no particular order from the temporary disk memory cache. If the cache fails this test, memory circuits may contain a fault.

Data Integrity Test. This test analyzes the data on the disk drive. The test determines if corrupted data is on the disk. Bad data can cause the program to falter even though the hard disk operates correctly.

File System Check. This routine performs a file-by-file check of the data stored on the hard disk.

Surface Scan. The magnetic material on the disk can become damaged, causing data to be unreadable. This routine locates unusable areas on the disk and marks them for future reference.

Diagnostic, Audit & Adjustment Menu System for NFL 3-8

Page 41

Main Menu (continued) Diagnostics Menu (continued) Switch Tests Menu

SWITCH TESTS

Select SWITCH TESTS at the Diagnostics Menu. Switch Tests verify proper operation of the game’s switches, including buttons and joystick switches.

Activate each switch, and the indicator on the menu changes state. Release the switch and the indicator returns to its previous, normally open or closed condition. You can test any combination of switches together. To exit the test, simultaneously press the middle two control buttons inside the coin door. The Switch Test Menu refers to these buttons as “volume buttons.”

PLAYER SWITCH INPUTS TEST

P1UPP3UPLEFT COIN
P1DOWNP3DOWNRIGHT COIN
P1LEFTP3LEFTP1 START
P1RIGHTP3RIGHTSLAM/TILT
P1JUMPP3JUMPTEST
P1PASSP3PASSP2 START
P1TURBOP3TURBOSERVICE CREDIT

CENTER COIN

P2UPP4UPEXTRA COIN
P2DOWNP4DOWNP3 START
P2LEFTP4LEFTP4 START
P2RIGHTP4RIGHTVOLUME DOWN
P2JUMPP4JUMPVOLUME UP
P2PASSP4PASS
P2TURBOP4TURBOBILL VALID.7

P1 49 WAY P2 49 WAY P3 49 WAY P4 49 WAY 24 24 24 24

PRESS BOTH PLAYER 1 AND PLAYER 2 START BUTTONS TO EXIT

SWITCH TEST MENU

Switches appear on the menu as colored boxes. Red boxes indicate an open state. Green indicates closed. Any other color indicates a fault condition. A single indication on the menu should exactly duplicate a button or joystick change. You'll notice a unique number for a switch recognized by game electronics.

Use Switch Tests to locate crossed wires, intermittent conditions and stuck switches.

NOTICE: Some switches may not be used with this game. If you can’t find one of the listed switches, check the wiring diagram.

Diagnostic, Audit & Adjustment Menu System for NFL 3-9

Page 42

Main Menu (continued) Diagnostics Menu (continued) DIP Switch Tests Menu

DIP-SWITCH TESTS Select DIP-SWITCH TESTS at the Diagnostics Menu. Two 8-position DIP switch banks reside on the SIO Board. DIP-Switch Tests allow you to check the position of the 16 switches in these banks. You can change the setting of any DIP switch without removing the circuit board cage.

The menu displays an illustration of each switch block and the current settings. You can change DIPswitch positions with power on. Set any switch, and then check the menu to verify that the new setting is enabled.

Refer to the charts for assistance in choosing switch positions. (* indicates factory defaults.) To exit the DIP-switch Test, press the left control button (inside the coin door).

Game-Selection Switch. Select NBA Showtime or NFL Blitz by flipping switch 8 at DIP bank U13. Then power down and up again. After you change the game play, you must change game artwork.

DIP Switch 1 (U13) Swi _| Sw2 | Sw3 | Sw4 | Sws | SW6 | SW7 | SW8 Coinage Control DIP Switch Off

CMOS: On*

USA1 Gert FrECA1 UK1 Off* | Off* | Off*

USA2 Ger2 FrECA2 UK2OnOffOff
USA3 Ger3 FrECA3 UK3OffOnOff
USA4 Ger4 FrECA4 UK4OnOnOff
USAS Ger5 FrECA5 UK5OffOffOn
USA9 Ger9 FrECA9 UK9OnOffOn
USA10 Ger10 Fr ECA10 UK ECAOffOnOn
USA ECA / Ger ECA / Fr ECA8OnOnOn
Free Play (All Countries)OnOnOn

Country USA Off* Off*

France On Off

Germany Off On

UK** On On Game Selection By player Off* By Switch 8 On Game at powerup NBA Showtime Off* NEL Blitz On **Except Free Play, which is “on” for SW2 through SW6.

DIP Switch 2 (U12) Swi | Sw2 | Sw3 | Sw4 | Sws | SW6 | SW7 | Sw8 Joystick Type 8-Way Off 49-Way On*

Monitor ResolutionMedium ResOff*

Low Res On

Unused7Off

= On

Unused-Off

7 On

Unused-Off

7 On Player Panel Type = 2-Player Off 4-Player On*

Power Up Test Active Off

Inactive On*

Operating Mode Game Mode Off* Test Mode On

Diagnostic, Audit & Adjustment Menu System for NFL 3-10

Page 43

Main Menu (continued) Diagnostics Menu (continued) Speaker Test Menu

SPEAKER TEST

Select SPEAKER TEST at the Diagnostics Menu. The Speaker Test provides audio signals to test the loudspeakers.

Use tests on the Speaker Test menu to verify operation of audio system components. Highlight an option with any player panel joystick. Select the option with any player panel button.

SPEAKER TESTS

LEFT CHANNEL

CENTER CHANNEL

RIGHT CHANNEL.

100 HZ TONE

1 KHZ TONE

PLAY TUNE

EXIT

SPEAKER TEST MENU

Channel and Tone Tests. The channel subtests employ voice announcements to verify speaker locations. Use the 100 Hz tone to check the speakers’ bass response. Small speakers with weak magnets or poor baffles may cause poor bass response.

Play Tune repeats a series of game sounds. Use PLAY TUNE to check speaker operation and fidelity. If your game has stereo speakers, run PLAY TUNE and test speaker phasing. Muddy, weak or distorted sound during this test may indicate crossed wires or out-of-phase speaker connections. Missing sounds may indicate audio cabling errors.

increase the volume level. Before returning to Game-Over Mode, reset the volume « ) NOTICE: Check the volume setting before testing. To test the speakers thoroughly, f level to its original setting.

Diagnostic, Audit & Adjustment Menu System for NFL 3-11

Page 44

Main Menu (continued) Audits Menu

AUDITS Select AUDITS at the Main Menu. The Audits menus permit you to review game play statistics. Additional menus give detailed reports for each player position on game starts, ends, cabinet abuse, fault conditions, etc.

Highlight an option with any player panel joystick. Select the option with any player panel button. The menu displays a list of the statistics available to you. Select an item to view the detailed report.

AUDITS

COIN AUDITS

CREDITS AUDITS

GAME AUDITS

TEAM STATS

OFFENSIVE PLAYS

DEFENSIVE PLAYS

EXCEPTION DUMP

CLEAR AUDITS

EXIT

AUDITS MENU

Data in the Audits menus helps you to keep records of the game’s popularity and earning potential. Use the highlight bar to select the desired subject on the Audits Menu. Each entry on the Audits Menu is the subject for an entire menu of bookkeeping information. On these menus, you can track favorite teams, frequently used offensive and defensive plays, etc.

Some audits menus also include histograms. Histogram menus allow graphical analysis of statistics. This permits visual comparisons between games. Histograms have no bar graphs until the system acquires enough data to plot.

Examine and record all game audit values before performing game service or repairs.

NOTICE: Be careful when clearing audit information. Once you clear data, you can’t restore it.

Diagnostic, Audit & Adjustment Menu System for NFL 3-12

Page 45

Main Menu (continued) Audits Menu (continued) Coin Audits Menu

COIN AUDITS Select COIN AUDITS at the Audits Menu. The Coin Audits menu permits you to assess the currency collection. This report menu presents revenue quantities and other important game statistics. Coin Audits is a read-only menu.

To exit, press any player panel button.

COIN AUDITS — PAGE:

LEFT SLOT COINS XXXXXXXX

RIGHT SLOT COINS XXXXXXXX

BILLS XXXXXXXX

CENTER SLOT COINS XXXXXXXX

EXTRA SLOT COINS XXXXXXXX

GAME STARTS XXXXXXXX

MID-GAME STARTS XXXXXXXX

CONTINUES XXXXXXXX

FREE QUARTERS AWARDED XXXXXXXX

FREE GAMES AWARDED XXXXXXXX

SERVICE CREDITS XXXXXXXX

TOTAL PLAYS XXXXXXXX

UP - NEXT / BUTTON - EXIT COIN AUDITS MENU, PAGE 1

The Coin Audits menu reports total quantities of coins, bills or credits collected by each active device. The menu doesn’t calculate the value of the collected currency.

This menu reports information, but doesn’t permit you to make changes. To reset the coin, bill and credit counters to zero, use the Clear Audits menu.

We recommend that you examine and record audit information before you make changes. Once you’ve cleared the counters, you can’t retrieve the previous data from the system.

COIN AUDITS — PAGE: 2

TOTAL PAID CREDITS = XXXXXXXX TOTAL XXXXXXXX

DOWN - PREV / BUTTON - EXIT COIN AUDITS MENU, PAGE 2

Diagnostic, Audit & Adjustment Menu System for NFL 3-13

Page 46

Main Menu (continued) Audits Menu (continued) Credits Audits Menu

CREDITS AUDITS Select CREDITS AUDITS at the Audits Menu. The Credits Audits menu permits you to assess the currency collection. This report menu presents revenue quantities and other important game statistics. Credits Audits is a read-only menu.

To exit, press any player panel button.

CREDITS AUDITS

CREDITS AVAILABLE XXXXXXXX

PRESS ANY BUTTON TO EXIT

CREDITS AUDITS MENU

Diagnostic, Audit & Adjustment Menu System for NFL 3-14

Page 47

Main Menu (continued) Audits Menu (continued) Game Audits Menu

GAME AUDITS Select GAME AUDITS at the Audits Menu. The Game Audits menus permit you to review the game play statistics. Game Audits is a read-only menu.

To exit, press any player panel button.

GAME AUDITS - PAGE: 1

TOTAL UPTIME 2 QUARTER GAMES TOTAL PLAY TIME 3 QUARTER GAMES GAME STARTED 4 QUARTER GAMES INITIALS ENTERED WENT INTO OVERTIME 1 <FG> PURCHASED AT START WENT INTO OVERTIME 2 CREATE PLAY SESSIONS WENT INTO OVERTIME 3 1 PLAYER 1 PLAYER FINISHES 2 PLAYER 2 PLAYER FINISHES 3 PLAYER 3 PLAYER FINISHES 4 PLAYER 4 PLAYER FINISHES 2P V CPU 2P V CPU FINISHES. 1 QUARTER GAMES HVS HLSW’S CPU WINS (FG) AVG H VS H TOTAL SCORE (FG) AVG H VS CPU TOTAL SCORE (FG) AVG H VS H WIN SCORE (FG)

UP — NEXT / BUTTON - EXIT

GAME AUDITS MENU, PAGE 1

The Game Audits menu reports information, but doesn’t permit you to make changes. Examine and record information at GAME AUDITS before deleting data at the Clear Audits Menu. Once you've cleared the counters, you can’t retrieve the previous data from the system.

GAME AUDIT MENU TERMS

TERM DEFINITION TERM DEFINITION

AVGAverageLSwYourgamecomputer’s _ internal

record-keeping counters CPU Central Processing Unit: The game

computerMachineNumber of power cycles (game turn-

Power-On ons) <FG>, (FG) | Full Game oT Overtime HVS CPU | Human versus CPU: Competition that

pits players against the game computerPVPlayer versus...

HVSH Human versus human: Competition | Total Uptime | Overall on-time for the game between human players computer

2PV Two players versus...

Diagnostic, Audit & Adjustment Menu System for NFL 3-15

Page 48

GAME AUDITS - PAGE: 2

AVG H VS HLOSS SCORE (FG) BIGGEST CPU WIN MARGIN (FG) BIGGEST CPU LOSS MARGIN (FG) TLF'S SBLF’S

DOWN — PREV / BUTTON - EXIT

GAME AUDITS MENU, PAGE 2

Diagnostic, Audit & Adjustment Menu System for NFL 3-16

Page 49

Main Menu (continued) Audits Menu (continued) Team Stats Menu

TEAM STATS Select TEAM STATS at the Audits Menu. Team Stats details the number of games played by each team in the league. Team Stats is a read-only menu.

To exit, press any player panel button.

TEAM STATS — PAGE: 1

ARIZONA CARDINALS

ATLANTA FALCONS,

BALTIMORE RAVENS

BUFFALO BILLS

CAROLINA PANTHERS.

CHICAGO BEARS

CINCINNATI BENGALS

CLEVELAND BROWNS

DALLAS COWBOYS

DENVER BRONCOS

DETROIT LIONS

GREEN BAY PACKERS

INDIANAPOLIS COLTS.

JACKSONVILLE JAGUARS

KANSAS CITY CHIEFS

MIAMI DOLPHINS MINNESOTA VIKINGS

NEW ENGLAND PATRIOTS

NEW ORLEANS SAINTS

NEW YORK GIANTS

NEW YORK JETS

OAKLAND RAIDERS

PHILADELPHIA EAGLES

PITTSBURCH STEELERS

SAN DIEGO CHARGERS

SAN FRANCISCO

SEATTLE SEAHAWKS

ST. LOUIS RAMS

TAMPA BAY BUCS

TENNESSEE TITANS

WASHINGTON REDSKINS

PRESS ANY BUTTON TO EXIT

TEAM STATS MENU

Diagnostic, Audit & Adjustment Menu System for NFL 3-17

Page 50

Main Menu (continued) Audits Menu (continued) Offensive Plays Menu

OFFENSIVE PLAYS Select OFFENSIVE PLAYS at the Audits Menu. Offensive Plays accounts for each play type as a percentage of all offensive plays. Offensive Plays is a read-only menu.

To exit, press any player panel button.

OFFENSIVE PLAYS — PAGE: 1

TEAMPLAY 1 0% BLIZZARD

TEAMPLAY 2 CRISS CROSS

TEAMPLAY 3 UP THE GUT

ZIG ZAG SCREEN RIGHT

SPIDER LEGS SUPER FLY

MONKEY MIDDLE PICK

SLIP SLIDE Kc SWEEP RIGHT

QB POST REVERSE ZIP

QUICK DISH Kc HB BLOCK

UPPER CUT EXTRA PLAY 1

DA BOMB EXTRA PLAY 2

HAIL MARY 2 EXTRA PLAY 3

TURMOIL EXTRA PLAY 4

BACK SPLIT EXTRA PLAY 5

SUBZERO EXTRA PLAY 6

DAWG HOOK EXTRA PLAY 7

U.T.B. DEEP EXTRA PLAY 8

CROSS SLANT EXTRA PLAY 9

PRESS ANY BUTTON TO EXIT

OFFENSIVE PLAYS MENU, PAGE 1

OFFENSIVE PLAYS — PAGE: 2 }PUNT = (“asiti|Sitsi‘—sSCSY FAKE PUNT

FIELD GOAL

FAKE F.G.

EXTRA POINT

PRESS ANY BUTTON TO EXIT

OFFENSIVE PLAYS MENU, PAGE 2

Diagnostic, Audit & Adjustment Menu System for NFL 3-18

Page 51

Main Menu (continued) Audits Menu (continued) Defensive Plays Menu

DEFENSIVE PLAYS Select DEFENSIVE PLAYS at the Audits Menu. Defensive Plays accounts for each play type as a percentage of all defensive plays. Defensive Plays is a read-only menu.

To exit, press any player panel button.

DEFENSIVE PLAYS — PAGE: 1

SAFE COVER 0%

1 MAN BLITZ0%BLOCK FG
2 MAN BLITZ0%BLOCK PUNT
SUICIDE BLITZ0%PUNT RETURN

ZONE BLITZ 0%

NEAR ZONE 0%

MEDIUM ZONE 0%

DEEP ZONE 0%

GOAL LINE 0%

EXTRA PLAY 1 0%

EXTRA PLAY 2 0%

EXTRA PLAY 3 0%

EXTRA PLAY 4 0%

EXTRA PLAY 5 0%

EXTRA PLAY 6 0%

EXTRA PLAY 7 0%

EXTRA PLAY 8

EXTRA PLAY 9

DEFENSIVE PLAYS MENU

Diagnostic, Audit & Adjustment Menu System for NFL 3-19

Page 52

Main Menu (continued) Audits Menu (continued) Exception Dump Menu

EXCEPTION DUMP Select EXCEPTION DUMP at the Audits Menu. Game programmers use the Exception Dump Menu to view register contents during program development. This menu has no field purpose. Exception Dump is a read-only menu.

To exit, press any player panel button.

Main Menu (continued) Audits Menu (continued) Clear Audits Menu

CLEAR AUDITS Select CLEAR AUDITS at the Audits Menu. The Clear Audits menu allows you to clear individual memory counters or to reset them all at once.

Highlight an option with any player panel joystick. Select the option with any player panel button.

CLEAR AUDITS

CLEAR COIN AUDITS

CLEAR CREDIT AUDITS

CLEAR GAME AUDITS

CLEAR TEAM STATS

CLEAR OFFENSIVE PLAYS

CLEAR DEFENSIVE PLAYS

CLEAR EXCEPTION DUMP.

CLEAR ALL

EXIT

CLEAR AUDITS MENU

You can reset any audit menu from the Clear Audits Menu. Choose an item and zero its counter. CLEAR ALL simultaneously changes all audit categories to factory default values. After you’ve selected an item, the system gives you the opportunity to escape this change. For example:

WANT TO CLEAR COIN AUDI

LAST CHANCE MENU

After you’ve selected and verified a clear function, the values reset. The system can’t restore the previous values. Examine and record utility values before you make changes.

Diagnostic, Audit & Adjustment Menu System for NFL 3-20

Page 53

Main Menu (continued) Adjustments Menu

ADJUSTMENTS Select ADJUSTMENTS at the Main Menu. The Adjustments menus permit you to change game characteristics. Use these menus to optimize game performance and earnings.

Highlight an option with any player panel joystick. Select the option with any player panel button.

ADJUSTMENTS

PRICING

FREE PLAY

ATTRACT SOUND

ADDITIONAL ADJUSTMENTS,

FULL FACTORY RESTORE

EXIT

ADJUSTMENTS MENU

Main Menu (continued) Adjustments Menu (continued) Pricing Menu

PRICING Select PRICING at the Adjustments Menu. The Pricing menus allow you to view current settings or change the cost of games. Custom pricing allows you to select the number of coins or credits required for each game. The game restores factory default values if you exchange the CPU Board or if the backup battery fails.

Highlight an option with any player panel joystick. Select the option with any player panel button.

You may reset options to factory defaults or change an option after viewing it. We recommend examining and recording pricing options before making changes.

You may save several custom prices and then choose between them as needed. On-screen instructions guide you through the process of creating custom price settings.

PRICING

SHOW CURRENT NORTH AMERICA SOUTH AMERICA EUROPE (A-H) EUROPE (I-U) ASIA AUSTRALIA ISTOM PRICING EXIT PRICING MENU

An additional box appears on screen to explain the available functions as you select each item.

Diagnostic, Audit & Adjustment Menu System for NFL 3-21

Page 54

STANDARD PRICING TABLE

NAMESTARTCONTINUE | CREDITSICOINCOIN? [ COIN?[COINS[COINa[BILL
ANTILLES,221725¢, 4G25¢1G)
AUSTRALIA 1221/3X20¢, 2/S7.0020¢$1.00
AUSTRALIA 2111/5X20¢, 1/$1.0020¢$1.00
AUSTRIA 1221/6Sch, 210Sch5Sch_| 10 Sch
AUSTRIA 2221/2X8Sch, 3/2X10Sch5Sch__|10Sch
BELGIUM 1221/20BF20BF| 20BF
BELGIUM 2223/20BF208F| 20BF
BELGIUM 3222/208F20BF| 20BF
BELGIUM ECA221/20BFspr| 208F__|SBF
CANADA 12272x 25¢, 3/8125¢25¢
CANADA 2221/2x 25¢,3/$125¢$1.00
CANADA 3223/ $1.00, 6 /$2.00$1.00| $2.00
CANADA ECA221/2x 25¢,3/$125¢$1.00 __| $2.00
DENMARK223/SDKr, 7ODKrSDKr__|10DKr
FINLAND22a/Fmk,iFmk__|5Fmk
FRANCE 1222ISFr, 5/10FrSFr10Fr
FRANCE 2212ISFr, 4/10FrSFr10Fr
FRANCE 3211/5Fr, 3/10FrSFr10Fr
FRANCE 4211/5Fr, 2/10FrSFr10Fr
FRANCE 5212ISFr, 5/10Fr, 11/2 X 10FrSFr10Fr
FRANCE 6212ISFr, 4/10Fr, 9/2 X 10FrSFr10Fr
FRANCE 7211/5Fr, 3/10Fr, 7/2 X 10FrSFr10Fr
FRANCE 8211/5Fr, 2/10Fr, 5/2 X 10FrSFr10Fr
FRANCE 92113 X 1Fr, 2/5Fr1FrSFr
FRANCE 10211/2 X 1 Fr, 3/5Fr1FrSFr
FRANCE 11211/3 X 1Fr, 2/5Fr, 5/2 X SFr1FrSFr
FRANCE 12211/2 X 1Fr, 3/5Fr, 7/2 X SFr1FrSFr
FRANCE ECA 171DISFr, 5/10FrFrSFr10Fr20Fr
FRANCE ECA 2112ISFr, 4/10Fr1FrSFr10Fr20Fr
FRANCE ECA 3111/5Fr, 3/10Fr1FrSFr10Fr20Fr
FRANCE ECA 4111/5Fr, 2/10Fr1FrSFr10Fr20Fr
FRANCE ECA 5112ISFr, 5/10Fr, 11/2 X 10Fr1FrSFr10Fr20Fr
FRANCE ECA 6112ISFr, 4/10Fr, 9/2 X 10Fr1FrSFr10Fr20Fr
FRANCE ECA 7111/5Fr, 3/10Fr, 7/2 X 10Fr1FrSFr10Fr20Fr
FRANCE ECA 8111/5Fr, 2/10Fr, 5/2 X 10Fr1FrSFr10Fr20Fr
FRANCE ECA 9111/3 X 1Fr, 2/5Fr1FrSFr10Fr20Fr
FRANCE ECA 10 | 111/2 X 1Fr, 3/5Fr1FrSFr10Fr20Fr
FRANCEECA11| 111/3 X 1 Fr, 2/5Fr, 5/10Fr1FrSFr10Fr20Fr
FRANCE ECA 12 | 111/2 X 1 Fr, 3/5Fr, 7 0Fr1FrSFr10Fr20Fr
FRANCEECA13 | 111/10F , 2/20Fr, 4/30Fr4FrSFr10Fr20Fr
FREE PLAY===None__|None__|None | None | None
GERMANY 422TDM, 6/5DM1DM‘SDM
GERMANY 2211/1DM, 7/5DM1DM5DM
GERMANY 3211/1DM, 8/5DM1DM5DM
GERMANY 4211/1DM, 5/5DM1DM5DM
GERMANY 5211/1DM, 6/5DM1DM5DM
GERMANY ECA1 | 221/1DM, 2/2DM, 6/5DM1DM2DM5DM
GERMANY ECA2 | 211/1DM, 2/2DM, 6/5DM1DM2DM5DM
GERMANYECA3 | 111/1DM, 2/2DM, 6/5DM1DM2DM5DM
HUNGARY22T2X10Ft, S/2X20FtT0Ft2OFt
ITALY221/500LItSo0Lit__|S00Lit
JAPAN 1221100¥en100100
JAPAN 2222/100Yen100100
JAPAN 3111/100Yen100100
JAPAN 4112m100Yen100100
JAPAN 5114mooYen100100
JAPAN 6111/2X100Yen100100
NETHERLANDS | 22TAHFI, 372.5HFITHI2.5HFI
NEW ZEALAND T| 111781$1$2
NEW ZEALAND 2_ | 112181St$2
NORWAY22SISNKr, 6/TONKrSNKr__|_10NKr
SPAIN 42217100Pta, 6/500Pla700Pta | 500Pta
SPAIN 2221/100Pta, 5/500Pta100Pta_|500Pta
SWEDEN22T/X1SKr, 2/6SKrSKr_|58Kr
SWITZERLAND?| 22T/ASFr, 6/5SFr1SFr___| 5SFr
SWITZERLAND 2 | 221/NSFr, 7/5SFt1sFr| 5SFr
SWITZERLAND 3_|221/ASFr, 8/5SFr1SFrSSFr

(Table continues on next page)

Diagnostic, Audit & Adjustment Menu System for NFL 3-22

Page 55

STANDARD PRICING TABLE, continued

NAMESTARTCONTINUE [ CREDITS/COINCOINT[COIN2[COINS | COIN4 | BILL
UK ECA111/50p, 3/81.00£1.00 | 50p20p0p.£2.00
UK ECA2711750p, 2181.00£1,00___|50p20p0p£2.00
UK ECAS111730p, 2/50p, 5/£1.00£1.00 | 50p20p0p.£2.00
UK4111150p, 3/81.00£1.00__|50p
UKS111150p, 2/81.00£1.00 | 50p
UK ECA 6111730p, 2/50p, 4/£1,00£1,00___|50p20p0p£2,00
UK ECATii3721.00£1.00__|50p20p0p.£2.00
UK ECA8111/50p, 2781.00, 4/£2.00£1.00 | 50p20p0p.£2.00
USAT221/25625¢25¢$1.00
usA2211/25¢25¢25¢$1.00
USA3111/25¢25¢25¢$1.00
usa111/50¢, 3/$1.0025¢25¢$1.00
USAS211/50¢, 4/$1.0025¢25¢$1.00
uUSAG6111/50¢25¢25¢$1.00
USAT111/50¢, 3/$1.0025¢25¢$1.00
usas221/50¢, 4/$1.0025¢25¢$1.00
usa321/25¢, 4/$1.0025¢25¢$1.00
USA10331/25¢, 4/$1.0025¢25¢$1.00
usA1t421/25¢, 4/$1.0025¢25¢$1.00
uSA12431/25¢, 4/$1.0025¢25¢$1.00
USA13441/25¢, 4/$1.0025¢25¢$1.00
USA ECA331/25¢, 4/$1.00$1.00 | 25¢10¢O5¢$1.00

Main Menu (continued) Adjustments Menu (continued) Pricing Menu (continued) Current Pricing Menu

Current Pricing Select SHOW CURRENT at the Pricing Menu. The Current Pricing Menu is a read-only menu. Use it to check pricing parameters for the pricing table your game is using. To select a new pricing table, return to the Pricing Menu. To invent your own pricing table, select Custom Pricing on the Pricing Menu.

Press any START button to exit from the menu.

CURRENT PRICING

LEFT SLOT UNITS

RIGHT SLOT UNITS

CENTER SLOT UNITS

EXTRA SLOT UNITS

BILL VALIDATOR UNITS

UNITS PER CREDIT

UNITS PER BONUS

MINIMUM UNITS

CREDITS TO START

CREDITS TO CONTINUE

MAX CREDITS

COINS PER BILL

PRESS ANY BUTTON TO EXIT

CURRENT PRICING MENU

Diagnostic, Audit & Adjustment Menu System for NFL 3-23

Page 56

The following table clarifies Pricing Menu terms...

MENU TERM DISCUSSION Slot Units; Cyber-currency. This adjustment assigns a number of “units” to each coin mechanism Bill Validator (DBV) or bill acceptor. For instance, if a quarter buys 1 unit, then $1 buys 4 units. (See Coins Units per Bill.) You insert a coin into a 1-unit coin acceptor. The system, due to its programming, knows that your coin is worth one unit. Units per Credit How many units equal one credit. (Units buy credit, the price of one game.) Units per Bonus Units awarded when a player earns a bonus. Minimum Units Until this many units accumulate, the system awards no credits. Credits to Start Number of games a player must purchase to begin play. Credits to Continue Number of games a player must purchase to resume play. Max Credits Limits the number of credits that the game will accept. Coins per Bill How many coins one bill is worth.

Main Menu (continued) Adjustments Menu (continued) Pricing Menu (continued) Custom Pricing Menu

Custom Pricing Select CUSTOM PRICING at the Pricing Menu. The Custom Pricing Menu permits you to program and use your own pricing table. You can save several pricing schemes and chose between them as desired.

Highlight an option with any player panel joystick. Change the option with any player panel button. Press any START button to save your pricing table and exit from the menu.

CUSTOM PRICING

CUSTOM PRICING OPENING MENU

Add allows you to write a new custom pricing scheme. If you choose ADD, the system directs you to... [] 1. Name your scheme. [] 2. Program pricing information. [] 3. Select the coin denomination for your scheme. [] 4. Retain or alter the pricing screen message. (Later, check it in Game Mode by pressing START.) [] 5. Save your pricing scheme. [] 6. Use your pricing scheme by selecting it.

Delete permits you to eliminate a single custom pricing scheme.

Edit lets you modify a stored custom pricing scheme.

Delete, when enabled, clears all custom pricing schemes.

Select enables you to choose which custom pricing scheme is the active one. Diagnostic, Audit & Adjustment Menu System for NFL 3-24

Page 57

Main Menu (continued) Adjustments Menu (continued) Pricing Menu (continued) Custom Pricing Menu (continued) Creating Pricing Scheme Menu

Creating Pricing Scheme After you name your custom pricing scheme, you encounter the Creating Pricing Scheme Menu. This menu is where you program the pricing scheme. You can save several pricing schemes and choose between them as desired.

Highlight an option with any player panel joystick. Select Change Mode with any player panel button. Use a joystick to change the option. Save your setting by pressing any player panel button. Press any START button to exit from the menu. Exiting invokes the Select Currency Menu. Use this menu to choose the coin denomination that players will use. Exit by choosing DONE.

CREATING XXXX

LEFT UNITS RIGHT UNITS

CENTER UNITS EXTRA UNITS

DBV UNITS UNITS PER CREDIT

UNITS / BONUS MIN UNITS

CREDITS TO START CREDITS TO CONT.

MAX CREDITS COINS / BILL

SHOW FRACTIONS LEFT COUNT

RIGHT COUNT CENTER COUNT

EXTRA COUNT DBV COUNT

USE STICK TO SELECT AN ITEM TO MODIFY PRESS ANY BUTTON TO MODIFY THE ITEM

PRESS ANY START BUTTON TO SAVE AND EXIT

CUSTOM PRICING MENU

SELECT CURRENC

DOLLAR POUND GUILDER SCHILLING FRANC KRONE MARKKA DEUTSCHE MARK LIRE FORINT PESETA YET DONE

SELECT CURRENCY MENU (PAGE 2 OF CREATING XXXX MENU)

Diagnostic, Audit & Adjustment Menu System for NFL 3-25

Page 58

The Custom Pricing Menu employs the same terms that appear on the Current Pricing Table. See the table below for definitions of these terms.

PRICING MENU TERMS MENU TERM DISCUSSION Slot Units; Cyber-currency. This adjustment assigns a number of “units” to each coin mechanism Bill Validator (DBV) or bill acceptor. For instance, if a quarter buys 1 unit, then $1 buys 4 units. (See Coins Units per Bill.) You insert a coin into a 1-unit coin acceptor. The system, due to its programming, knows that your coin is worth one unit. Units per Credit How many units equal one credit. (Units buy credit, the price of one game.) Units per Bonus Units awarded when a player earns a bonus. Minimum Units Until this many units accumulate, the system awards no credits. Credits to Start Number of games a player must purchase to begin play. Credits to Continue Number of games a player must purchase to resume play. Max Credits Limits the number of credits that the game will accept. Coins per Bill How many coins one bill is worth.

BASIC CUSTOM PRICING. Custom pricing creates an imaginary currency exchange. In this currency exchange, the coins of the realm are “units.” Think of units as a type of cyber-currency, useful only within the game software. By inserting coins, you purchase units.

Since units are only negotiable within game software, the system stores your units for you. When the system receives enough units, it buys a game for you. The price of a game is one “credit.” You can think of credits as a second form of cyber-currency.

Even though you've now bought one game, you may not be able to begin playing. In many pricing schemes, you must buy two or more credits to begin play. The idea here is something like a minimum order of goods at a store. That is, the operator can “shrink-wrap” two or more games in a package. You can’t play unless you buy the entire package.

1 /25¢ COIN; 1 CREDIT TO START. In a simple, quarter pricing scheme, the player inserts one coin to buy one unit. The system exchanges that unit for one credit. If CREDITS TO START contains the value one, then play commences. A dollar bill buys four units.

Left Slot UnitsValidator UnitsUnits / CreditCredits to StartCoins / Bill
14114

e1 / 3 X 25¢; 2 CREDITS TO START. Again, assuming quarter slots, here’s one way to implement 75¢ pricing... In this scheme, each coin that the player inserts buys one unit. The system exchanges three units for one credit. CREDITS TO START contains the value two. To play, the player must pay for two credits. In this scheme, a dollar buys four units.

Left Slot UnitsValidator UnitsUnits / CreditCredits to StartCoins / Bill
14324

«2 / 1 COIN; 6 CREDITS TO START. Now let’s consider a more unusual pricing scheme. Here, the player can buy two units with one coin. The system exchanges each of these units for one credit. Notice that CREDITS TO START contains the value six. To play, the player must insert two more coins to pay for six credits. Also notice that if the player pays with a bill, the system throws in an extra unit.

Left Slot UnitsValidator UnitsUnits / CreditCredits to StartCoins / Bill
29164

Diagnostic, Audit & Adjustment Menu System for NFL 3-26

Page 59

Main Menu (continued) Adjustments Menu (continued) Pricing Menu (continued) Custom Pricing Menu (continued) Current Pricing Prompt

Pricing Prompt After you exit the Select Currency Menu, you encounter the Current Pricing Prompt Menu. The Current Pricing Prompt Menu allows you to enter a brief pricing or advertising message. The video game machine displays your message during the Attract Mode.

Select YES at the menu’s first page. The Screen Message Entry Menu opens. You may enter up to three lines of text. Each line may include up to 32 alphanumeric characters. Here’s an example message...

1 CREDIT /2 COINS EAT AT JOE’S

Highlight a letter with any player panel joystick. Select the letter with any player panel button. Delete the rightmost character of the default message by selecting the on-screen asterisk (*). Watch the bottom of the screen to see your message line develop. Save the entire line and proceed to the second line by selecting the arrow (>). CURRENT PRICING PROMPT

1 CREDIT / 2 COINS

DO YOU WANT TO CHANGE?

CURRENT PRICING PROMPT MENU

PRICING — LINE 1

1 CREDIT /2 COINS

USE STICK TO MOVE / BUTTON TO SELECT

SCREEN MESSAGE ENTRY MENU (PRICING — LINE 1)

Diagnostic, Audit & Adjustment Menu System for NFL 3-27

Page 60

After you complete your message, you may edit it by reentering the Screen Message Entry Menu. To reenter the menu, choose EDIT from the Custom Pricing Menu.

Main Menu (continued) Adjustments Menu (continued) Pricing Menu (continued) Custom Pricing Menu (continued) Save Pricing Scheme

Save Pricing Scheme Exiting from the Screen Message Entry Menu invokes the Save Pricing Scheme Menu. The Save Pricing Scheme Menu allows you to save your pricing scheme.

Highlight an option with any player panel joystick. Select YES to save, or NO to delete your pricing scheme.

DO YOU WANT TO SAVE XXXXX?

YES

SAVE PRICING SCHEME MENU

To use the new pricing scheme, you must now select it. The program returns you to the Custom Pricing Menu. You'll notice a few more entries on the menu. Besides ADD and EXIT, you'll see that you can now EDIT or SELECT a pricing scheme.

Highlight SELECT with any player panel joystick. To use your pricing scheme, press any player panel button. The program acknowledges your pricing scheme choice and returns you to Custom Pricing Menu. Choose EXIT to return to the Pricing Menu.

DELETE

EDIT SELECT

EXIT

CUSTOM PRICING OPENING MENU

Diagnostic, Audit & Adjustment Menu System for NFL 3-28

Page 61

Main Menu (continued) Adjustments Menu (continued) Free Play Menu

Free Play Select FREE PLAY at the Adjustments Menu. Free play is a useful feature for promotions and long-term testing under play conditions. Enable free play to allow players to play the game without inserting currency. Disable free play to sell games.

Highlight an option with any player panel joystick. Select the option with any player panel button.

Main Menu (continued) Adjustments Menu (continued) Attract Sound Menu

Attract Sound Select ATTRACT SOUND at the Adjustments Menu. The Attract Mode operates between games. It attempts to lure prospective players into trying your game. Attract Mode sound may not be appropriate for some locations. The Attract Sound Menu allows you to enable or disable the Attract Mode sound feature. You can turn Attract Mode sound on or off without changing the game volume level.

Highlight an option with any player panel joystick. Select the option with any player panel button.

ENABLE ATTRACT MODE SOUNDS?

ATTRACT SOUND MENU

. NOTICE: After you enable Attract Mode sound, you can adjust the Attract Mode A volume level. See the Main Menu.

Diagnostic, Audit & Adjustment Menu System for NFL 3-29

Page 62

Main Menu (continued) Adjustments Menu (continued) Additional Adjustments Menu

ADDITIONAL ADJUSTMENTS Select ADDITIONAL ADJUSTMENTS at the Adjustments Menu. Additional Adjustments menu items allow you to set the game to match player requirements. These adjustments affect speed, challenge, rewards, etc. that determine player enjoyment.

Highlight an option with any player panel joystick. Select the option with any player panel button.

ADDITIONAL ADJUSTMENTS,

GAME DIFFICULTY DISCOUNT PRICE / CREDITS CLOCK SPEED

FREE GAME - FULL 4 PLR.

FREE GAME — FULL 1 ON 1

FREE GAME - FULL V. CPU

FREE QUARTER — 4 PLR.

FREE QUARTER — 1 ON 1 FREE QUARTER - V. CPU VIOLENCE

BAD LANGUAGE

CLEAR PLAYER RECORDS

TOURNAMENT MODE

ATTRACT MOVIE SOUND

EXIT

ADDITIONAL ADJUSTMENTS MENU

Game Difficulty allows you to alter the challenge that a game poses to players. Choose the level that most closely matches the players’ skills.

Discount Price / Credits adjusts the quantity of buy-in points to encourage multiple game purchases.

Clock Speed alters how much game time that a player can purchase for one credit. Choose one of these settings: Extra slow, slow, medium, fast or extra fast.

Free Games and Free Quarters. Use these features to provide incentives to good players.

Violence. You can remove violence from the game without affecting other game play characteristics.

Bad Language. You can remove rough language without affecting other game play characteristics.

Clear Player Records allows you to delete stored game play data.

Tournament Mode, when enabled, adapts your game’s scoring for tournament-style play.

Attract Movie Sound, when enabled, allows Attract Mode movie sound with Attract Mode sound off. The Attract Mode movie is only one component of the Attract Mode graphics.

Diagnostic, Audit & Adjustment Menu System for NFL 3-30

Page 63

Main Menu (continued) Adjustments Menu (continued) Full Factory Restore Menu

FULL FACTORY RESTORE Select FULL FACTORY RESTORE at the Adjustments Menu. The Full Factory Restore menu allows you to clear all memory counters at once.

Highlight an option with any player panel joystick. Select the option with any player panel button.

FULL FACTORY RESTORE MENU

NOTICE: Examine and record audit information before you make changes. Once you've cleared the counters, you can’t retrieve previous data from the system.

Examine and record utility values before you make changes. If you choose YES, the system restores all adjustments and audits to factory default values. This change isn’t reversible. The system can’t restore the previous values. With the settings restored, the system displays the Reset Complete Menu.

AUDITS & ADJUSTMENTS RESTORED

PRESS ANY BUTTON TO EXIT

RESET COMPLETED MENU

Diagnostic, Audit & Adjustment Menu System for NFL 3-31

Page 64

Main Menu (continued) Set Volume Level Menu

SET VOLUME LEVEL Select VOLUME LEVEL at the Main Menu. The Set Volume Level Menu appears, and music plays continuously.

Raise or lower the game’s sound level with any player panel joystick. (You can also use the volume up/down buttons on the diagnostic switch bracket.) Save your change and return to the Main Menu by pressing any player panel button.

SET VOLUME LEVEL

I —— =€=—S—tCS=«~

IP / DOWN TO ADJUST VOLUME

PRESS ANY BUTTON TO SET VOLUME AND EXIT

SET VOLUME LEVEL MENU

Loud games attract more player interest than games with low-level sound.

You can turn Attract Mode sound on or off without changing the game volume level. (See Adjustments.)

NOTICE: Sound level adjustments affect the volume of tests as well as of game play. If you set volume levels to minimum (zero), the speakers are silent during audio tests. We recommend setting volume levels to a moderately high value whenever you perform sound tests. After you complete tests, you may return sound levels to previous settings.

NOTICE: You can also change the volume level during Game Mode. Press VOLUME UP or VOLUME DOWN as necessary until you achieve the desired volume. These buttons are inside the coin door.

Diagnostic, Audit & Adjustment Menu System for NFL 3-32

Page 65

Main Menu (continued) Set Attract Volume Level Menu

SET ATTRACT VOLUME LEVEL Select ATTRACT VOLUME LEVEL at the Main Menu. You must enable Attract Mode sound before setting the Attract Mode volume level. (You can enable Attract Sound from the Adjustments Menu.)

When you display the Set Attract Volume Level Menu, music plays continuously. Raise or lower the game’s Attract Mode sound level with any player panel joystick. (You can also use the volume up/down buttons on the diagnostic switch bracket.) Save your change and return to the Main Menu by pressing any player panel button. Your setting won't affect the game play sound level.

SET ATTRACT VOLUME LEVEL

I =€=—tSC«~

UP / DOWN TO ADJUST VOLUME

PRESS ANY BUTTON TO SET VOLUME AND EXIT

SET ATTRACT VOLUME LEVEL MENU

A loud Attract Mode encourages player interest. You can turn Attract Mode sound on or off without changing the game volume level. (See Adjustments.)

Diagnostic, Audit & Adjustment Menu System for NFL 3-33

Page 66

Main Menu (continued) Utilities Menu

UTILITIES Select UTILITIES at the Main Menu. Utilities Menu items allow you to clear bookkeeping totals. From the Utilities Menu, you can also restore game adjustments to factory settings.

Highlight an option with any player panel joystick. Select the option with any player panel button.

UTILITIES

DUMP AUDITS CLEAR CREDITS CLEAR AUDITS RESET HIGH SCORES DEFAULT ADJUSTMENTS FULL FACTORY RESTORE

EXIT

UTILITIES MENU

Dump Audits allows you to send data to the game computer's serial port. You can connect a serial printer to make a paper record of your audit data.

Clear Credits opens a menu that allows you to zero the game’s credit data. Examine and record audit information before you make changes.

Clear Audits opens a menu that allows you to zero the game’s audit data.

Reset High Scores permits you to delete player names and scores that appear in the Attract Mode. This feature may be useful if players insert inappropriate language into the high score table.

Default Adjustments opens a menu that allows you to reset game adjustments to factory settings.

Full Factory Restore allows you to reset game adjustments and audits to factory settings.

NOTICE: Be careful when clearing audit information. Once you clear data, you can’t restore it.

Diagnostic, Audit & Adjustment Menu System for NFL 3-34

Page 67

NBA SHOWTIME Gop Eoirion/ NFL Bi1z72000 Goin Epivion

CONVERSION KIT

CHAPTER

FOUR

DIAGNOSTIC, AUDIT & ADJUSTMENT MENU SYSTEM FOR NBA SHOWTIME GAMES

NOTICE: Information in this manual is subject to change without notice. Midway reserves the right to make improvements in equipment as progress in engineering warrants.

NOTICE: GAME-SELECTION SWITCH. Select NBA Showtime or NFL Blitz by flipping switch 8 at DIP bank U13. Then power down and up again. After you change the game play, you must change game artwork.

Diagnostic, Audit & Adjustment Menu System for NBA 4-1

Page 68

MENU SYSTEM

WHAT IS THE MENU SYSTEM? The game’s Menu System is a series of auditing, game adjustment and diagnostic screens. We call these screens menus, because they present options in menu-like lists. You can easily access and apply menus to optimize game performance. For instance...

« Use game audits menus to assess game performance. « Use adjustment menus to help you to customize game performance. For instance, you can restore factory default game settings. You can also calibrate player controls for accuracy. « Use diagnostic menus to verify proper equipment operation.

ACTIVATING THE MENU SYSTEM Open the coin door. Find the TEST MODE switch inside. Press TEST MODE to invoke the Menu System. The game system responds by exiting Game Mode and entering Diagnostic Mode. You can also invoke the Menu System by turning on DIP bank U12, switch 8. (To reenter Game Mode, turn off switch 8.)

AUTOMATIC TESTS In Diagnostic Mode, the Power-On Self-Test (POST) activates. This routine runs automatically. It can detect faults that cause game or Menu System malfunctions. POST usually takes less than a minute. The test doesn’t display anything. Instead, the system boot loader indicates the software revision number and serial numbers. The system boot loader also displays a sound-loading message and other useful information.

At the end of POST, the system displays the Control Functions Menu.

CONTROL FUNCTIONS The Control Functions Menu is purely informational. It appears for five seconds. Then the Menu System automatically displays the Dual Game Adjustment Menu.

The Control Functions Menu introduces the menu navigation controls. The key point is that you can use either player or diagnostic controls to navigate menus. Diagnostic control switches are particularly helpful when you must troubleshoot player switches. This manual discusses the controls in more detail in this chapter’s Main Menu section. Also see the page on the menu that interests you.

STICK UP/VOLUME UP — MOVE UP

STICK DOWN/VOLUME DOWN — MOVE DOWN

STICK RIGHT — MOVE RIGHT

STICK LEFT —- MOVE LEFT

PUSH BUTTON/TEST BUTTON - SELECT

5 SECONDS TO DIAG ENTRY

CONTROL FUNCTIONS MENU

Diagnostic, Audit & Adjustment Menu System for NBA 4-2

Page 69

DUAL GAME ADJUSTMENT MENU The Dual Game Adjustment Menu is another informational, read-only menu. It appears until you choose to exit. This menu reminds you that some NBA settings also affect NFL game play. Press any button to exit to the Main Menu.

ATTENTION!

ANY CHANGES TO THE FOLLOWING ADJUSTMENTS.

UPDATE BOTH NBA AND NFL.

PRICING

FREE PLAY

VOLUME LEVEL

DISCOUNT PRICE / CREDITS

ATTRACT MODE SOUND ON / OFF

THIS ALSO INCLUDES DEFAULT ADJUSTMENTS.

AND

FULL FACTORY RESTORE FUNCTIONS.

PRESS ANY BUTTON TO EX!

DUAL GAME ADJUSTMENT MENU

MAIN MENU The Main Menu offers you access to the game machine’s test, bookkeeping and programmable features. Game audits, adjustments and diagnostics are line items on the Main Menu. Selecting an item opens its submenu. Every submenu presents various options that you may act upon.

NBA MAIN MENU

DIAGNOSTICS AUDITS ADJUSTMENTS VOLUME LEVEL ATTRACT VOLUME LEVEL UTILITIES NFL MAIN MENU EXIT TO NFL EXIT TO NBA

MAIN MENU

MENU LAYOUT Menus differ, but related information tends to occupy the same menu locations.

e The block at the top, center of each menu displays the current menu title. « Data (menu items, video signals, statistics, reports, etc.) appears in the center of the menu. « Messages (explanations, control functions, revision levels) display at the bottom of the menu.

MENU NAVIGATION CONTROLS Use any player panel joystick to highlight a desired menu item. You can only select one highlighted item at a time. To select a highlighted item, press any player panel button. Operator control buttons inside the

Diagnostic, Audit & Adjustment Menu System for NBA 4-3

Page 70

coin door serve as backup menu navigation controls. Press VOLUME UP or VOLUME DOWN buttons to highlight a menu item. Press TEST MODE to select a highlighted item.

EXIT OPTIONS To exit the NBA menus and simultaneously enter the NFL menus, choose NFL MAIN MENU. To return the game to play, highlight either EXIT TO NFL or EXIT TO NBA. Your choice determines the game that will boot. Next, press any button.

NOTICE: This manual depicts some menus as having two pages. Your video game machine may present these same menus as one-pagers. Monitor resolution affects whether a menu has a second screen.

Main Menu (continued) Diagnostics Menu

DIAGNOSTICS Select DIAGNOSTICS at the Main Menu. Diagnostic tests allow you to verify the condition of the electrical and electronic hardware in the game.

Highlight a test with any player panel joystick. Select the option with any player panel button.

DIAGNOSTICS

MONITOR SETUP.

SYSTEM INFO

SOUND SUBSYSTEM

DISK TESTS

SWITCH TESTS

DIP-SWITCH TESTS

SPEAKER TEST

EXIT

DIAGNOSTICS MENU

Diagnostic tests assist you in checking and adjusting the game’s major systems. By running diagnostics, you can gain an insight into both system hardware and game software. Periodically running diagnostics is a crucial part of maintaining game performance and player satisfaction. Sometimes you can improve game performance by running a diagnostic test and making appropriate adjustments.

Diagnostic, Audit & Adjustment Menu System for NBA 4-4

Page 71

Main Menu (continued) Diagnostics Menu (continued) Monitor Setup Menu

MONITOR SETUP. Select MONITOR SETUP at the Diagnostics Menu. The Monitor Patterns routine provides test screens to verify monitor performance or make adjustments.

Highlight an option with any player panel joystick. Select the option with any player panel button.

MONITOR SETUP.

COLOR BARS

CROSSHATCH

RED SCREEN

BLUE SCREEN

GREEN SCREEN

WHITE SCREEN

BLACK SCREEN

50 PCT. GRAY SCREEN

25 PCT. GRAY SCREEN

EXIT

MONITOR SETUP MENU

Color Bars fills the screen with colored stripes. Use the color bars to help you to check or adjust monitor brightness and contrast. The color bars also expose defects in horizontal linearity. Each color bar consists of 32 intensity levels. On a properly adjusted monitor, the top 31 of these levels are visible. Each bar should appear sharp, clear and distinct from bars on either side. Incorrect adjustment can cause missing detail at the top or bottom of a bar. Bent bars indicate horizontal linearity flaws, such as pie crust, pincushion or barrel distortion. (Correct color bar colors, left to right: Red, Green, Blue, Black, White, Cyan, Yellow, Violet.) Set controls as follows: 1. Adjust BRIGHTNESS and CONTRAST to minimum. 2. Turn up BRIGHTNESS until the pixels in the black stripe begin to glow (turn dark gray). 3. Bring up the CONTRAST control until you can see 31 bars.

Crosshatch Patterns fill the screen with a grid and a series of dots. Crosshatch Patterns help you to check or adjust several monitor parameters: These include convergence, linearity, active viewing area and dynamic focus. The grid and the dots should be all white in color, with no fringes or parallel images. The lines should be straight and the dots round. For more detail on these adjustments, consult service literature from the monitor manufacturer.

Color Screen tests fill the screen with 100% of the chosen color at normal intensity. The Color Screen tests help you to check or adjust monitor intensity, black level, blanking and color purity. Each screen should be absolutely uniform from top to bottom and side to side. No retrace lines or noise should be visible. Color Screens may not hold their uniformity if the monitor degaussing circuit is defective.

White, Gray and Black Screens fill the screen with black, gray or white at various intensities. These monochrome screens help you to check or adjust monitor convergence, purity, contrast and intensity. These screens also simplify black level and color gun control settings. The screens should be uniform with no color tints or distortion. No retrace lines or noise should be visible.

If tests indicate a need for adjustment, use controls on the Monitor Remote Adjustment Board.

Diagnostic, Audit & Adjustment Menu System for NBA 4-5

Page 72

Main Menu (continued) Diagnostics Menu (continued) System Information Menu

SYSTEM INFORMATION Select SYSTEM INFO at the Diagnostics Menu. The System Information Menu provides the current version numbers of this game’s hardware and software. Use these numbers to describe the system during parts replacement, service calls, etc.

Highlight an option with any player panel joystick. Select the option with any player panel button.

SYSTEM INFORMATION

MIDWAY GAMES, INC. XXXXXXX SYSTEM

SERIAL NUMBER: XXXXXXXXX

GAME: XXXXXXXXXX

DATE OF MANUFACTURE: XX/XX/XX

PRESS ANY BUTTON TO EXIT

SYSTEM INFORMATION MENU

The System Information menu reports information, but doesn’t permit you to make changes. The Title line identifies the manufacturer of this game and the electronic board set used in this product. The Serial Number, Game and Date of Manufacture identify the game name and production run.

Diagnostic, Audit & Adjustment Menu System for NBA 4-6

Page 73

Main Menu (continued) Diagnostics Menu (continued) Sound Subsystem Menu

SOUND SUBSYSTEM TEST Select SOUND SUBSYSTEM at the Diagnostics Menu. Sound Subsystem Tests verify that audio components are connected and operate properly.

Highlight an option with any player panel joystick. Select the option with any player panel button.

SOUND SUBSYSTEM TEST

BOOT VERSION: XX.XX

SDRC VERSION: XX.XX

PORT STATUS: GOOD

CHECKSUM: XXXX

SRAM: OK

DRAM: OK

TONE STATUS: GOOD

OS VERSION: XX.XX

PRESS ANY BUTTON TO EXIT

SOUND SUBSYSTEM MENU

Version, Status, Checksum and RAM Reports are diagnostic routines. These routines analyze the digital sound circuits and can detect sound memory problems. Test results appear as numbers or messages. Sounds may also accompany some tests. Reports other than GOOD or OK indicate a problem.

Diagnostic, Audit & Adjustment Menu System for NBA 4-7

Page 74

Main Menu (continued) Diagnostics Menu (continued) Disk Tests Menu

DISK TESTS Select DISK TESTS at the Diagnostics Menu. Disk Tests allow you to verify proper operation of the hard disk drive assembly.

Highlight an option with any player panel joystick. Select the option with any player panel button.

DISK TESTS

DISK INFORMATION

SEQUENTIAL READ

SEQUENTIAL CACHE READ RANDOM READ

RANDOM CACHE READ

DATA INTEGRITY TEST

FILE SYSTEM CHECK

SURFACE SCAN

EXIT

DISK TESTS MENU

Disk Information. The Disk Information routine verifies the interface between the CPU Board Assembly and hard disk drive. The processor requests disk information. Data cannot be retrieved successfully if there is a problem.

Sequential Read. This routine tries to access every bit of data in the order it is stored directly on the disk. The hard disk drive media may be defective if this routine cannot be completed successfully.

Sequential Cache Read. This routine tries to access every bit of data in the order it is stored in the temporary disk memory cache. If this test is not successful, the memory circuits may be faulty.

Random Read. This routine tries to access every bit of data in no particular order directly from the disk. This test may detect problems with ability to position the drive heads accurately over the requested data.

Random Cache Read. This routine tries to access every bit of data in no particular order from the temporary disk memory cache. If the cache fails this test, memory circuits may contain a fault.

Data Integrity Test. This test analyzes the data on the disk drive. The test determines if corrupted data is on the disk. Bad data can cause the program to falter even though the hard disk operates correctly.

File System Check. This routine performs a file-by-file check of the data stored on the hard disk.

Surface Scan. The magnetic material on the disk can become damaged, causing data to be unreadable. This routine locates unusable areas on the disk and marks them for future reference.

Diagnostic, Audit & Adjustment Menu System for NBA 4-8

Page 75

Main Menu (continued) Diagnostics Menu (continued) Switch Tests Menu

SWITCH TESTS

Select SWITCH TESTS at the Diagnostics Menu. Switch Tests verify proper operation of the game’s switches, including buttons and joystick switches.

Activate each switch, and the indicator on the menu changes state. Release the switch and the indicator returns to its previous, normally open or closed condition. You can test any combination of switches together. To exit the test, simultaneously press the middle two control buttons inside the coin door. The Switch Test Menu refers to these buttons as “volume buttons.”

PLAYER SWITCH INPUTS TEST

P1UPP3UPLEFT COIN
P1DOWNP3DOWNRIGHT COIN
P1LEFTP3LEFTP1 START
P1RIGHTP3RIGHTSLAM/TILT
P1SHOOTP3SHOOTTEST
P1PASSP3PASSP2 START
P1TURBOP3TURBOSERVICE CREDIT

CENTER COIN

P2UPP4UPEXTRA COIN
P2DOWNP4DOWNP3 START
P2LEFTP4LEFTP4 START
P2RIGHTP4RIGHTVOLUME DOWN
P2SHOOTP4SHOOTVOLUME UP
P2PASSP4PASS
P2TURBOP4TURBOBILL VALID.7

P1 49 WAY P2 49 WAY P3 49 WAY P4 49 WAY 24 24 24 24

PRESS BOTH PLAYER 1 AND PLAYER 2 START BUTTONS TO EXIT

SWITCH TEST MENU

Switches appear on the menu as colored boxes. Red boxes indicate an open state. Green indicates closed. Any other color indicates a fault condition. A single indication on the menu should exactly duplicate a button or joystick change. You'll notice a unique number for a switch recognized by game electronics.

Use Switch Tests to locate crossed wires, intermittent conditions and stuck switches.

NOTICE: Some switches may not be used with this game. If you can’t find one of the listed switches, check the wiring diagram.

Diagnostic, Audit & Adjustment Menu System for NBA 4-9

Page 76

Main Menu (continued) Diagnostics Menu (continued) DIP Switch Tests Menu

DIP-SWITCH TESTS Select DIP-SWITCH TESTS at the Diagnostics Menu. Two 8-position DIP switch banks reside on the SIO Board. DIP-Switch Tests allow you to check the position of the 16 switches in these banks. You can change the setting of any DIP switch without removing the circuit board cage.

The menu displays an illustration of each switch block and the current settings. You can change DIPswitch positions with power on. Set any switch, and then check the menu to verify that the new setting is enabled.

Refer to the charts for assistance in choosing switch positions. (* indicates factory defaults.) To exit the DIP-switch Test, press the left control button (inside the coin door).

Game-Selection Switch. Select NBA Showtime or NFL Blitz by flipping switch 8 at DIP bank U13. Then power down and up again. After you change the game play, you must change game artwork.

DIP Switch 1 (U13) Swi _| Sw2 | Sw3 | Sw4 | Sws | SW6 | SW7 | SW8 Coinage Control DIP Switch Off

CMOS: On*

USA1 Gert FrECA1 UK1 Off ) Off* | Off*

USA2 Ger2 FrECA2 UK2OnOffOff
USA3 Ger3 FrECA3 UK3OffOnOff
USA4 Ger4 FrECA4 UK4OnOnOff
USAS Ger5 FrECA5 UK5OffOffOn
USA9 Ger9 FrECAQ UK9OnOffOn
USA10 Ger10 Fr ECA10 UK ECAOffOnOn
USA ECA / Ger ECA / Fr ECA8OnOnOn
Free Play (All Countries)OnOnOn

Country USA Off* Off*

France On Off

Germany Off On

UK** On On Game Selection By player Off* By Switch 8 On Game at powerup NBA Showtime Off* NEL Blitz On **Except Free Play, which is “on” for SW2 through SW6.

DIP Switch 2 (U12) Swi | Sw2 | Sw3 | Sw4 | SwWs5 | SW6 | SW7 | Sw8 Joystick Type 8-Way Off 49-Way On*

Monitor ResolutionMedium ResOff*

Low Res On

Unused7Off

= On

Unused-Off

= On

Unused-Off

7 On Player Panel Type = 2-Player Off 4-Player On*

Power Up Test Active Off

Inactive On*

Operating Mode Game Mode Off* Test Mode On

Diagnostic, Audit & Adjustment Menu System for NBA 4-10

Page 77

Main Menu (continued) Diagnostics Menu (continued) Speaker Test Menu

SPEAKER TEST

Select SPEAKER TEST at the Diagnostics Menu. The Speaker Test provides audio signals to test the loudspeakers.

Use tests on the Speaker Test menu to verify operation of audio system components. Highlight an option with any player panel joystick. Select the option with any player panel button.

SPEAKER TEST

LEFT CHANNEL

CENTER CHANNEL

RIGHT CHANNEL.

100 HZ TONE

1 KHZ TONE

PLAY TUNE

EXIT

SPEAKER TEST MENU

Channel and Tone Tests. The channel subtests employ voice announcements to verify speaker locations. Use the 100 Hz tone to check the speakers’ bass response. Small speakers with weak magnets or poor baffles may cause poor bass response.

Play Tune repeats a series of game sounds. Use PLAY TUNE to check speaker operation and fidelity. If your game has stereo speakers, run PLAY TUNE and test speaker phasing. Muddy, weak or distorted sound during this test may indicate crossed wires or out-of-phase speaker connections. Missing sounds may indicate audio cabling errors.

increase the volume level. Before returning to Game-Over Mode, reset the volume « y NOTICE: Check the volume setting before testing. To test the speakers thoroughly, f level to its original setting.

Diagnostic, Audit & Adjustment Menu System for NBA 4-11

Page 78

Main Menu (continued) Audits Menu

AUDITS Select AUDITS at the Main Menu. The Audits menus permit you to review game play statistics. Additional menus give detailed reports for each player position on game starts, ends, cabinet abuse, fault conditions, etc.

Highlight an option with any player panel joystick. Select the option with any player panel button. The menu displays a list of the statistics available to you. Select an item to view the detailed report.

AUDITS

COIN AUDITS

CREDITS AUDITS

GAME AUDITS

TEAM STATS

GAME FEATURES

EXCEPTION DUMP

CLEAR AUDITS

EXIT

AUDITS MENU

Data in the Audits menus helps you to keep records of the game’s popularity and earning potential. Use the highlight bar to select the desired subject on the Audits Menu. Each entry on the Audits Menu is the subject for an entire menu of bookkeeping information. On these menus, you can track favorite teams, frequently used offensive and defensive plays, etc.

Some audits menus also include histograms. Histogram menus allow graphical analysis of statistics. This permits visual comparisons between games. Histograms have no bar graphs until the system acquires enough data to plot.

Examine and record all game audit values before performing game service or repairs.

NOTICE: Be careful when clearing audit information. Once you clear data, you cannot restore it.

Diagnostic, Audit & Adjustment Menu System for NBA 4-12

Page 79

Main Menu (continued) Audits Menu (continued) Coin Audits Menu

COIN AUDITS Select COIN AUDITS at the Audits Menu. The Coin Audits menu permits you to assess the currency collection. This report menu presents revenue quantities and other important game statistics. Coin Audits is a read-only menu.

To exit, press any player panel button.

COIN AUDITS - PAGE: 1

XXXXXXXX

XXXXXXXX

XXXXXXXX

CENTER SLOT COINS XXXXXXXX

EXTRA SLOT COINS XXXXXXXX

GAME STARTS XXXXXXXX

MID-GAME STARTS XXXXXXXX

CONTINUES XXXXXXXX

CHALLENGER ACCEPTED XXXXXXXX

FREE QUARTERS AWARDED — XXXXXXXX FREE GAMES AWARDED XXXXXXXX

SERVICE CREDITS XXXXXXXX

UP — NEXT / BUTTON - EXIT COIN AUDITS MENU

The Coin Audits menu reports total quantities of coins, bills or credits collected by each active device. The menu doesn’t calculate the value of the collected currency.

This menu reports information, but doesn’t permit you to make changes. To reset the coin, bill and credit counters to zero, use the Clear Audits menu.

We recommend that you examine and record audit information before you make changes. Once you've cleared the counters, you can’t retrieve the previous data from the system.

COIN AUDITS — PAG

TOTAL PLAYS XXXXXXX

TOTAL PAID CREDITS = XXXXXXX TOTAL XXXXXXX

DOWN - PREV / BUTTON - EXIT COIN AUDITS MENU, PAGE 2

Diagnostic, Audit & Adjustment Menu System for NBA 4-13

Page 80

Main Menu (continued) Audits Menu (continued) Credits Audits Menu

CREDITS AUDITS Select CREDITS AUDITS at the Audits Menu. The Credits Audits menu permits you to assess the currency collection. This report menu presents revenue quantities and other important game statistics. Credits Audits is a read-only menu.

To exit, press any player panel button.

CREDITS AUDITS

CREDITS AVAILABLE XXXXXXXX

PRESS ANY BUTTON TO EXIT

CREDITS AUDITS MENU

Diagnostic, Audit & Adjustment Menu System for NBA 4-14

Page 81

Main Menu (continued) Audits Menu (continued) Game Audits Menu

GAME AUDITS Select GAME AUDITS at the Audits Menu. The Game Audits menus permit you to review the game play statistics. Game Audits is a read-only menu.

To exit, press any player panel button.

GAME AUDITS - PAGE: 1

MACHINE POWER-ONXXWENT INTO OVERTIME 1
TOTAL UPTIMEXXWENT INTO OVERTIME 2
TOTAL PLAYTIMEXXWENT INTO OT 3
GAMES STARTEDXX1 PLAYER FINISHES
INITIALS ENTEREDXX2 PLAYER FINISHES
<FG> PURCHASED AT STARTXX3 PLAYER FINISHES
CREATE PLAYER SESSIONSXX4 PLAYER FINISHES
1 PLAYERXX2P V CPU FINISHES
2 PLAYERXXHVS HLSW'S.
3 PLAYERXXCPU WINS (FG)
4 PLAYERXXAVG H VS H TOTAL SCORE (FG)
2P V CPUXXAVG H VS CPU TOTAL SCORE (FG) AVG
1 QUARTER GAMESXXAVG H VS H WIN SCORE (FG)
2 QUARTER GAMESXXAVG H VS HLOSS SCORE (FG)
3 QUARTER GAMESXXBIGGEST CPU WIN MARGIN (FG)
4 QUARTER GAMESXXBIGGEST CPU LOSS MARGIN (FG)

XX XX XX XX XX XX

GAME AUDITS MENU

The Game Audits menu reports information, but doesn’t permit you to make changes. Examine and record information at GAME AUDITS before deleting data at the Clear Audits Menu. Once you've cleared the counters, you can't retrieve the previous data from the system.

GAME AUDIT MENU TERMS

TERM DEFINITION TERM DEFINITION

AVGAverageLSwYourgamecomputer’s _ internal

record-keeping counters CPU Central Processing Unit: The game

computerMachineNumber of power cycles (game turn-

Power-On ons) <FG>, (FG) | Full Game oT Overtime HVS CPU | Human versus CPU: Competition that

pits players against the game computerPVPlayer versus...

HVSH Human versus human: Competition | Total Uptime | Overall on-time for the game between human players computer

2PV Two players versus...

Diagnostic, Audit & Adjustment Menu System for NBA 4-15

Page 82

Main Menu (continued) Audits Menu (continued) Team Stats Menu

TEAM STATS Select TEAM STATS at the Audits Menu. The Team Stats Menu details the number of games played by each team in the league. Team Stats is a read-only menu.

To exit, press any player panel button.

TEAM STATS — PAGE: 1

NEW JERSEY NETS ATLANTA HAWKS.

BOSTON CELTICS

CHARLOTTE HORNETS

CHICAGO BULLS

CLEVELAND CAVALIERS

DALLAS MAVERICKS

DENVER NUGGETS

DETROIT PISTONS

GOLDEN STATE WARRIORS

HOUSTON ROCKETS.

INDIANAPOLIS PACERS.

LOS ANGELES CLIPPERS

LOS ANGELES LAKERS

MIAMI HEAT

MILWAUKEE BUCKS 0%

NEW YORK NICKS

ORLANDO MAGIC.

PHILADELPHIA 76ERS.

PHOENIX SUNS

PORTLAND TRAILBLAZERS.

SACRAMENTO KINGS

SAN ANTONIO SPURS

SEATTLE SUPERSONICS

TORONTO RAPTORS

UTAH JAZZ

VANCOUVER GRIZZLIES

WASHINGTON WIZARDS

MINNESOTA TIMBERWOLVES

PRESS ANY B: IN TO EXIT

TEAM STATS MENU

Diagnostic, Audit & Adjustment Menu System for NBA 4-16

Page 83

Main Menu (continued) Audits Menu (continued) Game Features Menu

GAME FEATURES Select GAME FEATURES at the Audits Menu. Game Features tracks play statistics that relate characters in the game and game play. Game Features is a read-only menu.

To exit, press any player panel button.

GAME FEATURES — PAGE: 1

NUMBER OF PLAYER RECORDS. CREATP CUSTOM UNIFORM

NUMBER OF LRU RECORDS CREATP TEAM UNIFORM

RECORDS FROM CREATE PLAYER CREATP NICKNAME

NUMBER OF PLAYER FIRE CREATP AVG HEIGHT PTS

AVG PTS PLAYER FIRE CREATP AVG WEIGHT PTS

NUMBER OF TEAM FIRE CREATP AVG PWR PTS

AVG PTS TEAM FIRE CREATP AVG SPEED PTS

NUMBER OF ALLEY OOPS

NUMBER OF DOUBLE DUNKS

CREATP MASCOT HEADS

CREATP NBA HEADS

CREATP FEMALE HEADS CREATP AVG TWOPTS PTS

CREATP AVG STEAL PTS

CREATP AVG BLOCK PTS

CREATP AVG DUNK PTS

CREATP AVG DRIBBLE PTS

CREATP UM HEADS PRIV1

CREATP MID HEADS PRIV2

CREATP OTHER HEADS PRIV3

CREATP DEFAULT UNIFORM PRIV4

PRIVS

PRIV6

PRIV7

GAME FEATURES MENU, PAGE 1

Number Of Player Records. Number of player initial sets entered in CMOS RAM.

Number Of LRU Records. Number of record slots (space for player data) left in CMOS RAM.

Records From Create Player. Number of player records produced in Create Player Mode.

Number Of Player Fire. Number of times a player has started on fire.

Avg Pts Player Fire. Average number of points that player scored while player was on fire.

Number Of Team Fire. Number of times that the team has started on fire.

Diagnostic, Audit & Adjustment Menu System for NBA 4-17

Page 84

Avg Pts Team Fire. Average number of points that the team scored while it was on fire. Number Of Alley Oops. Total number of alley oops performed. Number Of Double Dunks. Total number of double dunks performed. Creatp Mascot Heads. Number of player-created characters with mascot heads. Creatp NBA Heads. Number of player-created characters with NBA-personality heads. Creatp Female Heads. Number of player-created characters with female heads. Creatp UM Heads. Number of player-created characters with Universal Studios® monster heads. Creatp Mid Heads. Number of player-created characters with Midway Games® heads. Creatp Other Heads. Number of player-created characters with custom heads. Creatp Default Uniform. Number of player-created characters with the selected team’s uniforms. Creatp Custom Uniform. Number of player-created characters with custom uniforms. Creatp Team Uniform. Number of player-created characters with specific team uniforms. Creatp Nickname. Number of player-created characters with nicknames. Creatp Avg Height Pts. Average height attribute setting. Creatp Avg Weight Pts. Average weight attribute setting. Creatp Avg Pwr Pts. Average power attribute setting. Creatp Avg Speed Pts. Average speed attribute setting. Creatp Avg TwoPts Pts. Average two-point shot attribute setting. Creatp Avg Steal Pts. Average stealing attribute setting. Creatp Avg Block Pts. Average blocking attribute setting. Creatp Avg Dunk Pts. Average dunking attribute setting. Priv1. Number of times player-created characters include privilege 1 (a player selection). Priv2. Number of times player-created characters include privilege 2 (a player selection). Priv3. Number of times player-created characters include privilege 3 (a player selection). Priv4. Number of times player-created characters include privilege 4 (a player selection). Priv5. Number of times player-created characters include privilege 5 (a player selection). Priv6. Number of times player-created characters include privilege 6 (a player selection). Priv7. Number of times player-created characters include privilege 7 (a player selection). Priv8. Number of times player-created characters include privilege 8 (a player selection). Game With Creatp. Number of games played with player-created characters. Win V CPU With Creatp. Number of player-won games with player-created characters. Win V Human With Creatp. Number of computer-won games with player-created characters. Tournament Games. Number of games played in Tournament-Scoring Mode. Timer Level. Speed at which game machine produces time-released and created characters. TLF’s. A counter employed by designers (has no purpose in the field). SBLF’s. A counter employed by designers (has no purpose in the field).

Highlight an option with any player panel joystick. Select the option with any player panel button.

Diagnostic, Audit & Adjustment Menu System for NBA 4-18

Page 85

GAME FEATURES — PAGE: 2

PRIV4

PRIVS

PRIV6

PRIV7

PRIV8

GAME WITH CREATP.

WIN V CPU WITH CREATP.

WIN V HUMAN WITH CREATP

TOURNAMENT GAMES

TIMER LEVEL

TLF’S

SBLF’S

DOWN — PREV / BUTTON - EXIT.

GAME FEATURES MENU, PAGE 2

Diagnostic, Audit & Adjustment Menu System for NBA 4-19

Page 86

Main Menu (continued) Audits Menu (continued) Exception Dump Menu

EXCEPTION DUMP Select EXCEPTION DUMP at the Audits Menu. Game programmers use the Exception Dump Menu to view register contents during program development. This menu has no field purpose. Exception Dump is a read-only menu.

To exit, press any player panel button.

Main Menu (continued) Audits Menu (continued) Clear Audits Menu

CLEAR AUDITS Select CLEAR AUDITS at the Audits Menu. The Clear Audits menu allows you to clear individual memory counters or to reset them all at once.

Highlight an option with any player panel joystick. Select the option with any player panel button.

CLEAR AUDITS

CLEAR COIN AUDITS

CLEAR CREDITS AUDITS

CLEAR GAME AUDITS

CLEAR TEAM STATS

CLEAR GAME FEATURES

CLEAR GAME RESETS

CLEAR EXCEPTION DUMP.

CLEAR ALL

EXIT

CLEAR AUDITS MENU

You can reset any audit menu from the Clear Audits Menu. Choose an item and zero its counter. CLEAR ALL simultaneously changes all audit categories to factory default values. After you’ve selected an item, the system gives you the opportunity to escape this change. For example:

WANT TO CLEAR COIN AUDIT:

LAST CHANCE MENU

After you’ve selected and verified a clear function, the values reset. The system can’t restore the previous values. Examine and record utility values before you make changes.

Diagnostic, Audit & Adjustment Menu System for NBA 4-20

Page 87

Main Menu (continued) Adjustments Menu

ADJUSTMENTS Select ADJUSTMENTS at the Main Menu. The Adjustments menus permit you to change game characteristics. Use these menus to optimize game performance and earnings.

Highlight an option with any player panel joystick. Select the option with any player panel button.

ADJUSTMENTS

PRICING

FREE PLAY

ATTRACT SOUND

ADDITIONAL ADJUSTMENTS,

FULL FACTORY RESTORE

EXIT

ADJUSTMENTS MENU

Main Menu (continued) Adjustments Menu (continued) Pricing Menu

PRICING Select PRICING at the Adjustments Menu. The Pricing menus allow you to view current settings or change the cost of games. Custom pricing allows you to select the number of coins or credits required for each game. The game restores factory default values if you exchange the CPU Board or if the backup battery fails.

Highlight an option with any player panel joystick. Select the option with any player panel button.

You may reset options to factory defaults or change an option after viewing it. We recommend examining and recording pricing options before making changes.

You may save several custom prices and then choose between them as needed. On-screen instructions guide you through the process of creating custom price settings.

PRICING

SHOW CURRENT NORTH AMERICA SOUTH AMERICA EUROPE (A-H) EUROPE (I-U) ASIA AUSTRALIA ISTOM PRICING EXIT

PRICING MENU

An additional box appears on screen to explain the available functions as you select each item.

Diagnostic, Audit & Adjustment Menu System for NBA 4-21

Page 88

STANDARD PRICING TABLE

NAMESTARTCONTINUE | CREDITSICOINCOIN?[COIN2[COINS[COINa[BILL
ANTILLES,221725¢, 4G25¢1G
AUSTRALIA 1221/3206, 2/$7.0020¢$1.00
AUSTRALIA 2111/5X20¢, 1/$1.0020¢$1.00
AUSTRIA 1221/6Sch, 210Sch5Sch_| 10 Sch
AUSTRIA 2111/2X5Sch, 3/2X10Sch5Sch__|10Sch
BELGIUM 1221/20BF20BF| 20BF
BELGIUM 2223/20BF208F| 20BF
BELGIUM 3222/208F20BF| 20BF
BELGIUM ECA221/20BFsopF | 208F | SBF
CANADA 12272x 25¢, 378125¢25¢
CANADA 2221/2x 25¢,3/$125¢$1.00
CANADA 3223/ $1.00, 6 /$2.00$1.00| $2.00
CANADA ECA221/2x 25¢,3/$125¢$1.00 __| $2.00
DENMARK22SISDKr, 7ODKrSDKr__|10DKr
FINLAND22a/AFmk,iFmk | S5Fmk
FRANCE 1222ISFr, 5/10FrSFr10Fr
FRANCE 2212ISFr, 4/10FrSFr10Fr
FRANCE 3211/5Fr, 3/10FrSFr10Fr
FRANCE 4211/5, 2/10FrSFr10Fr
FRANCE 5212ISFr, 5/10Fr, 11/2 X 10FrSFr10Fr
FRANCE 6212ISFr, 4/10Fr, 9/2 X 10FrSFr10Fr
FRANCE 7211/5Fr, 3/10Fr, 7/2 X 10FrSFr10Fr
FRANCE 8211U5Fr, 2/10Fr, 5/2 X 10FrSFr10Fr
FRANCE 92113 X 1 Fr, 2/5Fr1FrSFr
FRANCE 10211/2 X 1 Fr, 3/5Fr1FrSFr
FRANCE 11211/3 X 1Fr, 2/5Fr, 5/2 X SFr1FrSFr
FRANCE 12211/2 X 1Fr, 3/5Fr, 7/2 X SFr4FrSFr
FRANCE ECA 171DISFr, 5/10FrFrSFr10Fr20Fr
FRANCE ECA 2112ISFr, 4/10Fr1FrSFr10Fr20Fr
FRANCE ECA 3111/5Fr, 3/10Fr1FrSFr10Fr20Fr
FRANCE ECA 4111/5Fr, 2/10Fr1FrSFr10Fr20Fr
FRANCE ECA 5112I5Fr, 5/10Fr, 11/2 X 10Fr1FrSFr10Fr20Fr
FRANCE ECA 6112ISFr, 4/10Fr, 9/2 X 10Fr1FrSFr10Fr20Fr
FRANCE ECA 7111/5Fr, 3/10Fr, 7/2 X 10Fr1FrSFr10Fr20Fr
FRANCE ECA 8111/5Fr, 2/10Fr, 5/2 X 10Fr1FrSFr10Fr20Fr
FRANCE ECA 9111/3 X 1 Fr, 2/5Fr1FrSFr10Fr20Fr
FRANCE ECA 10 | 111/2 X 1Fr, 3/5Fr1FrSFr10Fr20Fr
FRANCEECA11| 1113 X 1Fr, 2/5Fr, 5/10Fr1FrSFr10Fr20Fr
FRANCE ECA 12 | 111/2 X 1Fr, 3/5Fr, 7 0Fr1FrSFr10Fr20Fr
FRANCEECA13 | 111/10F , 2/20F, 4/30Fr4FrSFr10Fr20Fr
FREE PLAY===None__|None| None | None | None
GERMANY 422TDM, 6/5DM1DM‘SDM
GERMANY 2211/1DM, 7/5DM1DM5DM
GERMANY 3211/1DM, 8/5DM1DM5DM
GERMANY 4211/1DM, 5/5DM1DM5DM
GERMANY 5211/1DM, 6/5DM1DM5DM
GERMANY ECA1 | 221/1DM, 2/2DM, 6/5DM1DM2DM5DM
GERMANY ECA2 | 211/1DM, 2/2DM, 6/5DM1DM2DM5DM
GERMANYECA3 | 111/1DM, 2/2DM, 6/5DM1DM2DM5DM
HUNGARY22T2X10Ft, S/2X20FtT0Ft2OFt
ITALY221/500LItS00LIt | S00LIt
JAPAN 1221100¥en100100
JAPAN 2222m00Yen100100
JAPAN 3111/100Yen100100
JAPAN 4112i00Yen100100
JAPAN 5114mooYen100100
JAPAN 6111/2X100Yen100100
NETHERLANDS | 22TAHFI, 372.5HFITHFI2.5HFI
NEW ZEALAND 1| 111781St$2
NEW ZEALAND 2__|112181$t$2
NORWAY22SISNKr, 6/1ONKrSNKr__|_10NKr
SPAIN 42217100Pta, 6/500PIa700Pta | 500Pta
SPAIN 2221/100Pta, 5/500Pta100Pta_|500Pta
SWEDEN22T/X1SKr, 2/6SKrSKr_|58Kr
SWITZERLAND?| 22T/ASFr, 6/5SFr1SFr___|5SFr
SWITZERLAND 2 | 221/ISFr, 7/5SFt1sFr| 5SFr
SWITZERLAND 3_|221/ASFr, 8/5SFr1SFrSSFr

(Table continues on next page)

Diagnostic, Audit & Adjustment Menu System for NBA 4-22

Page 89

STANDARD PRICING TABLE, continued

NAMESTARTCONTINUE [ CREDITS/COINCOINT[COIN2[COINS | COIN4 | BILL
UK ECA111/50p, 3/81.00£1.00 | 50p20p0p.£2.00
UK ECA2111750p, 2181.00£1,00__|50p20p0p£2.00
UK ECAS111730p, 2/50p, 5/£1.00£1.00__|50p20p0p.£2.00
UK4111150p, 3/81.00£1.00 | 50p
UK5111750p, 2/81.00£1.00__|50p
UK ECA 6171730p, 2/50p, 481,00£1,00___|50p20pTop£2,00
UK ECATii3721.00£1.00__|50p20p0p.£2.00
UK ECA8111/50p, 2/81.00, 4/£2.00£1.00 | 50p20p0p.£2.00
USAT221/25625¢25¢$1.00
usaA2211/25¢25¢25¢$1.00
USA3111/25¢25¢25¢$1.00
usa111/50¢, 3/$1.0025¢25¢$1.00
USAS211/50¢, 4/$1.0025¢25¢$1.00
uUsAG6111/50¢25¢25¢$1.00
USAT111/50¢, 3/$1.0025¢25¢$1.00
usas221/50¢, 4/$1.0025¢25¢$1.00
usa321/25¢, 4/$1.0025¢25¢$1.00
USA10331/25¢, 4/$1.0025¢25¢$1.00
USA11421/25¢, 4/$1.0025¢25¢$1.00
usA12431/25¢, 4/$1.0025¢25¢$1.00
USA13441/25¢, 4/$1.0025¢25¢$1.00
USA ECA331/25¢, 4/$1.00$1.00 | 25¢10¢O5¢$1.00

Main Menu (continued) Adjustments Menu (continued) Pricing Menu (continued) Current Pricing Menu

Current Pricing Select SHOW CURRENT at the Pricing Menu. The Current Pricing Menu is a read-only menu. Use it to check pricing parameters for the pricing table your game is using. To select a new pricing table, return to the Pricing Menu. To invent your own pricing table, select Custom Pricing on the Pricing Menu.

Press any START button to exit from the menu.

CURRENT PRICING

LEFT SLOT UNITS

RIGHT SLOT UNITS

CENTER SLOT UNITS

EXTRA SLOT UNITS

BILL VALIDATOR UNITS

UNITS PER CREDIT

UNITS PER BONUS

MINIMUM UNITS

CREDITS TO START

CREDITS TO CONTINUE

MAX CREDITS.

COINS PER BILL

CURRENT PRICING MENU

Diagnostic, Audit & Adjustment Menu System for NBA 4-23

Page 90

The following table clarifies Pricing Menu terms...

MENU TERM DISCUSSION Slot Units; Cyber-currency. This adjustment assigns a number of “units” to each coin mechanism Bill Validator (DBV) or bill acceptor. For instance, if a quarter buys 1 unit, then $1 buys 4 units. (See Coins Units per Bill.) You insert a coin into a 1-unit coin acceptor. The system, due to its programming, knows that your coin is worth one unit. Units per Credit How many units equal one credit. (Units buy credit, the price of one game.) Units per Bonus Units awarded when a player earns a bonus. Minimum Units Until this many units accumulate, the system awards no credits. Credits to Start Number of games a player must purchase to begin play. Credits to Continue Number of games a player must purchase to resume play. Max Credits Limits the number of credits that the game will accept. Coins per Bill How many coins one bill is worth.

Main Menu (continued) Adjustments Menu (continued) Pricing Menu (continued) Custom Pricing Menu

Custom Pricing Select CUSTOM PRICING at the Pricing Menu. The Custom Pricing Menu permits you to program and use your own pricing table. You can save several pricing schemes and chose between them as desired.

Highlight an option with any player panel joystick. Change the option with any player panel button. Press any START button to save your pricing table and exit from the menu.

CUSTOM PRICING

CUSTOM PRICING OPENING MENU

Add allows you to write a new custom pricing scheme. If you choose ADD, the system directs you to... [] 1. Name your scheme. [] 2. Program pricing information. [] 3. Select the coin denomination for your scheme. [] 4. Retain or alter the pricing screen message. (Later, check it in Game Mode by pressing START.) [] 5. Save your pricing scheme. [] 6. Use your pricing scheme by selecting it.

Delete permits you to eliminate a single custom pricing scheme.

Edit lets you modify a stored custom pricing scheme.

Delete, when enabled, clears all custom pricing schemes.

Select enables you to choose which custom pricing scheme is the active one. Diagnostic, Audit & Adjustment Menu System for NBA 4-24

Page 91

Main Menu (continued) Adjustments Menu (continued) Pricing Menu (continued) Custom Pricing Menu (continued) Creating Pricing Scheme Menu

Creating Pricing Scheme After you name your custom pricing scheme, you encounter the Creating Pricing Scheme Menu. This menu is where you program the pricing scheme. You can save several pricing schemes and choose between them as desired.

Highlight an option with any player panel joystick. Select Change Mode with any player panel button. Use a joystick to change the option. Save your setting by pressing any player panel button. Press any START button to exit from the menu. Exiting invokes the Select Currency Menu. Use this menu to choose the coin denomination that players will use. Exit by choosing DONE.

CREATING XXXX

LEFT UNITS RIGHT UNITS

CENTER UNITS EXTRA UNITS

DBV UNITS UNITS PER CREDIT

UNITS / BONUS MIN UNITS

CREDITS TO START CREDITS TO CONT.

MAX CREDITS COINS / BILL

SHOW FRACTIONS LEFT COUNT

RIGHT COUNT CENTER COUNT

EXTRA COUNT DBV COUNT

USE STICK TO SELECT AN ITEM TO MODIFY PRESS ANY BUTTON TO MODIFY THE ITEM

PRESS ANY START BUTTON TO SAVE AND EXIT

CUSTOM PRICING MENU

SELECT CURRENC

DOLLAR POUND GUILDER SCHILLING FRANC KRONE MARKKA DEUTSCHE MARK LIRE FORINT PESETA YET DONE

SELECT CURRENCY MENU (PAGE 2 OF CREATING XXXX MENU)

Diagnostic, Audit & Adjustment Menu System for NBA 4-25

Page 92

The Custom Pricing Menu employs the same terms that appear on the Current Pricing Table. See the table below for definitions of these terms.

PRICING MENU TERMS MENU TERM DISCUSSION Slot Units; Cyber-currency. This adjustment assigns a number of “units” to each coin mechanism Bill Validator (DBV) or bill acceptor. For instance, if a quarter buys 1 unit, then $1 buys 4 units. (See Coins Units per Bill.) You insert a coin into a 1-unit coin acceptor. The system, due to its programming, knows that your coin is worth one unit. Units per Credit How many units equal one credit. (Units buy credit, the price of one game.) Units per Bonus Units awarded when a player earns a bonus. Minimum Units Until this many units accumulate, the system awards no credits. Credits to Start Number of games a player must purchase to begin play. Credits to Continue Number of games a player must purchase to resume play. Max Credits Limits the number of credits that the game will accept. Coins per Bill How many coins one bill is worth.

BASIC CUSTOM PRICING. Custom pricing creates an imaginary currency exchange. In this currency exchange, the coins of the realm are “units.” Think of units as a type of cyber-currency, useful only within the game software. By inserting coins, you purchase units.

Since units are only negotiable within game software, the system stores your units for you. When the system receives enough units, it buys a game for you. The price of a game is one “credit.” You can think of credits as a second form of cyber-currency.

Even though you've now bought one game, you may not be able to begin playing. In many pricing schemes, you must buy two or more credits to begin play. The idea here is something like a minimum order of goods at a store. That is, the operator can “shrink-wrap” two or more games in a package. You can’t play unless you buy the entire package.

1 /25¢ COIN; 1 CREDIT TO START. In a simple, quarter pricing scheme, the player inserts one coin to buy one unit. The system exchanges that unit for one credit. If CREDITS TO START contains the value one, then play commences. A dollar bill buys four units.

Left Slot UnitsValidator UnitsUnits / CreditCredits to StartCoins / Bill
14114

e1 / 3 X 25¢; 2 CREDITS TO START. Again, assuming quarter slots, here’s one way to implement 75¢ pricing... In this scheme, each coin that the player inserts buys one unit. The system exchanges three units for one credit. CREDITS TO START contains the value two. To play, the player must pay for two credits. In this scheme, a dollar buys four units.

Left Slot UnitsValidator UnitsUnits / CreditCredits to StartCoins / Bill
14324

«2 / 1 COIN; 6 CREDITS TO START. Now let’s consider a more unusual pricing scheme. Here, the player can buy two units with one coin. The system exchanges each of these units for one credit. Notice that CREDITS TO START contains the value six. To play, the player must insert two more coins to pay for six credits. Also notice that if the player pays with a bill, the system throws in an extra unit.

Left Slot UnitsValidator UnitsUnits / CreditCredits to StartCoins / Bill
29164

Diagnostic, Audit & Adjustment Menu System for NBA 4-26

Page 93

Main Menu (continued) Adjustments Menu (continued) Pricing Menu (continued) Custom Pricing Menu (continued) Current Pricing Prompt

Pricing Prompt After you exit the Select Currency Menu, you encounter the Current Pricing Prompt Menu. The Current Pricing Prompt Menu allows you to enter a brief pricing or advertising message. The video game machine displays your message during the Attract Mode.

Select YES at the menu’s first page. The Screen Message Entry Menu opens. You may enter up to three lines of text. Each line may include up to 32 alphanumeric characters. Here’s an example message...

1 CREDIT /2 COINS EAT AT JOE’S

Highlight a letter with any player panel joystick. Select the letter with any player panel button. Delete the rightmost character of the default message by selecting the on-screen asterisk (*). Watch the bottom of the screen to see your message line develop. Save the entire line and proceed to the second line by selecting the arrow (>). CURRENT PRICING PROMPT

1 CREDIT /2 COINS

DO YOU WANT TO CHANGE?

CURRENT PRICING PROMPT MENU

PRICING — LINE 1

1 CREDIT /2 COINS

USE STICK TO MOVE / BUTTON TO SELECT

SCREEN MESSAGE ENTRY MENU (PRICING — LINE 1)

Diagnostic, Audit & Adjustment Menu System for NBA 4-27

Page 94

After you complete your message, you may edit it by reentering the Screen Message Entry Menu. To reenter the menu, choose EDIT from the Custom Pricing Menu.

Main Menu (continued) Adjustments Menu (continued) Pricing Menu (continued) Custom Pricing Menu (continued) Save Pricing Scheme

Save Pricing Scheme Exiting from the Screen Message Entry Menu invokes the Save Pricing Scheme Menu. The Save Pricing Scheme Menu allows you to save your pricing scheme.

Highlight an option with any player panel joystick. Select YES to save, or NO to delete your pricing scheme.

DO YOU WANT TO SAVE XXXXX?

YES

SAVE PRICING SCHEME MENU

To use the new pricing scheme, you must now select it. The program returns you to the Custom Pricing Menu. You'll notice a few more entries on the menu. Besides ADD and EXIT, you'll see that you can now EDIT or SELECT a pricing scheme.

Highlight SELECT with any player panel joystick. To use your pricing scheme, press any player panel button. The program acknowledges your pricing scheme choice and returns you to Custom Pricing Menu. Choose EXIT to return to the Pricing Menu.

DELETE

EDIT SELECT

EXIT

CUSTOM PRICING OPENING MENU

Diagnostic, Audit & Adjustment Menu System for NBA 4-28

Page 95

Main Menu (continued) Adjustments Menu (continued) Free Play Menu

Free Play Select FREE PLAY at the Adjustments Menu. Free Play is a useful feature for promotions and long-term testing under play conditions. Enable Free Play to allow players to play the game without inserting currency. Disable Free Play to sell games.

Highlight an option with any player panel joystick. Select the option with any player panel button.

Main Menu (continued) Adjustments Menu (continued) Attract Sound Menu

Attract Sound Select ATTRACT SOUND at the Adjustments Menu. The Attract Mode operates between games. It attempts to lure prospective players into trying your game. Attract Mode sound may not be appropriate for some locations. The Attract Sound Menu allows you to enable or disable the Attract Mode sound feature. You can turn Attract Mode sound on or off without changing the game volume level.

Highlight an option with any player panel joystick. Select the option with any player panel button.

ENABLE ATTRACT MODE SOUNDS?

ATTRACT SOUND MENU

=> NOTICE: After you enable Attract Mode sound, you can adjust the Attract Mode A volume level. See the Main Menu.

Diagnostic, Audit & Adjustment Menu System for NBA 4-29

Page 96

Main Menu (continued) Adjustments Menu (continued) Additional Adjustments Menu

ADDITIONAL ADJUSTMENTS Select ADDITIONAL ADJUSTMENTS at the Adjustments Menu. Additional Adjustments menu items allow you to set the game to match player requirements. These adjustments affect speed, challenge, rewards, etc. that determine player enjoyment.

Highlight an option with any player panel joystick. Select the option with any player panel button.

ADDITIONAL ADJUSTMENTS,

GAME DIFFICULTY DISCOUNT PRICE / CREDITS CLOCK SPEED FREE GAME — FULL 4 PLR. FREE GAME - FULL 1 ON 1 FREE GAME - FULL V. CPU FREE QUARTER - FULL 4 PLR. FREE QUARTER - FULL 1 ON 1 FREE QUARTER — FULL V. CPU CLEAR PLAYER RECORDS CLEAR WORLD RECORDS PLAYER HEAD SIZE TOURNAMENT MODE COMPUTER ASSISTANCE ATTRACT MOVIE SOUND EXIT ADDITIONAL ADJUSTMENTS MENU

Game Difficulty allows you to alter the challenge that a game poses to players. Choose the level that most closely matches the players’ skills.

Discount Price / Credits adjusts the quantity of buy-in points to encourage multiple game purchases.

Clock Speed alters how much game time that a player can purchase for one credit. Choose one of these settings: Extra slow, slow, medium, fast or extra fast.

Free Game, when enabled, allows the program to award a free game. The free game may be a fourplayer or a one-on-one game. The free game may also involve competition against the game computer.

Free Quarter. The program divides games into quarters, as in NBA rules. The Free Quarter feature, when enabled, allows the program to award a free game quarter. The free quarter may be a four-player or a one-on-one quarter. The free quarter may also involve competition against the game computer.

Clear Player Records allows you to zero out game play data. Examine and record this information before you clear it. Once you've cleared player records, you can’t retrieve the previous data.

Clear World Records allows you to zero out world record data. Examine and record this information before you clear it. Once you've cleared player records, you can’t retrieve the previous data.

Player Head Size allows you to alter the head size of on-screen characters. This feature determines whether the characters appear more lifelike, or more like caricatures. Choose “normal” or “big.”

Tournament Mode, when enabled, adapts your game’s scoring for tournament-style play.

Diagnostic, Audit & Adjustment Menu System for NBA 4-30

Page 97

Computer Assistance, when enabled, permits the game computer to aid players in play action.

Attract Movie Sound, when enabled, allows Attract Mode movie sound with Attract Mode sound off. The Attract Mode movie is only one component of the Attract Mode graphics.

Main Menu (continued) Adjustments Menu (continued) Full Factory Restore Menu

FULL FACTORY RESTORE Select FULL FACTORY RESTORE at the Adjustments Menu. The Full Factory Restore menu allows you to clear all memory counters at once.

Highlight an option with any player panel joystick. Select the option with any player panel button.

RESTORE ADJUSTMENTS & AUDITS’

FULL FACTORY RESTORE MENU

NOTICE: Examine and record audit information before you make changes. Once you've cleared the counters, you can’t retrieve previous data from the system.

Examine and record utility values before you make changes. If you choose YES, the system restores all adjustments and audits to factory default values. This change isn’t reversible. The system can’t restore the previous values. With the settings restored, the system displays the Reset Complete Menu.

AUDITS & ADJUSTMENTS RESTORED

PRESS ANY BUTTON TO EXIT

RESET COMPLETED MENU

Diagnostic, Audit & Adjustment Menu System for NBA 4-31

Page 98

Main Menu (continued) Set Volume Level Menu

SET VOLUME LEVEL Select VOLUME LEVEL at the Main Menu. The Set Volume Level Menu appears, and music plays continuously.

Raise or lower the game’s sound level with any player panel joystick. (You can also use the volume up/down buttons on the diagnostic switch bracket.) Save your change and return to the Main Menu by pressing any player panel button.

SET VOLUME LEVEL

I —— =€=—S—tCS=«~

IP / DOWN TO ADJUST VOLUME

PRESS ANY BUTTON TO SET VOLUME AND EXIT

SET VOLUME LEVEL MENU

Loud games attract more player interest than games with low-level sound.

You can turn Attract Mode sound on or off without changing the game volume level. (See Adjustments.)

NOTICE: Sound level adjustments affect the volume of tests as well as of game play. If you set volume levels to minimum (zero), the speakers are silent during audio tests. We recommend setting volume levels to a moderately high value whenever you perform sound tests. After you complete tests, you may return sound levels to previous settings.

NOTICE: You can also change the volume level during Game Mode. Press VOLUME UP or VOLUME DOWN as necessary until you achieve the desired volume. These buttons are inside the coin door.

Diagnostic, Audit & Adjustment Menu System for NBA 4-32

Page 99

Main Menu (continued) Set Attract Volume Level Menu

SET ATTRACT VOLUME LEVEL Select ATTRACT VOLUME LEVEL at the Main Menu. You must enable Attract Mode sound before setting the Attract Mode volume level. (You can enable Attract Sound from the Adjustments Menu.)

When you display the Set Attract Volume Level Menu, music plays continuously. Raise or lower the game’s Attract Mode sound level with any player panel joystick. (You can also use the volume up/down buttons on the diagnostic switch bracket.) Save your change and return to the Main Menu by pressing any player panel button. Your setting won't affect the game play sound level.

SET ATTRACT VOLUME LEVEL

I =€=—tSC«~

UP / DOWN TO ADJUST VOLUME

PRESS ANY BUTTON TO SET VOLUME AND EXIT

SET ATTRACT VOLUME LEVEL MENU

A loud Attract Mode encourages player interest. You can turn Attract Mode sound on or off without changing the game volume level. (See Adjustments.)

Diagnostic, Audit & Adjustment Menu System for NBA 4-33

Page 100

Main Menu (continued) Utilities Menu

UTILITIES Select UTILITIES at the Main Menu. Utilities Menu items allow you to clear bookkeeping totals. From the Utilities Menu, you can also restore game adjustments to factory settings.

Highlight an option with any player panel joystick. Select the option with any player panel button.

UTILITIES

DUMP AUDITS CLEAR CREDITS CLEAR AUDITS RESET HIGH SCORES DEFAULT ADJUSTMENTS FULL FACTORY RESTORE EXIT

UTILITIES MENU

Dump Audits allows you to send data to the game computer's serial port. You can connect a serial printer to make a paper record of your audit data.

Clear Credits opens a menu that allows you to zero the game’s credit data. Examine and record audit information before you make changes.

Clear Audits opens a menu that allows you to zero the game’s audit data.

Reset High Scores permits you to delete player names and scores that appear in the Attract Mode. This feature may be useful if players insert inappropriate language into the high score table.

Default Adjustments opens a menu that allows you to reset game adjustments to factory settings.

Full Factory Restore allows you to reset game adjustments and audits to factory settings.

NOTICE: Be careful when clearing audit information. Once you clear data, you can’t restore it.

Diagnostic, Audit & Adjustment Menu System for NBA 4-34

Page 101

NBA SHOWTIME Gop EDITIoN/ NFL Bi172000 Goin Epivion

CONVERSION KIT

CHAPTER

FIVE

i eenoy i Fai aur reconnect ground wires or replace metal shields may result in radio requency interference.

NOTICE: The term VGM refers to the video game machine.

Wiring 5-1

Page 102

Function Wire Color JAMMA Chart

Function Wire Color

Ground Black Ground Black Ground Black Ground Black +5VDC Red +5VDC Red +5VDC Red +5VDC Red -5VDC Yellow -5VDC. Yellow +12VDC Orange +12VDC Orange Key N/C Key N/C Coin Counter 2 Brown-Red Coin Counter 1 Brown Not Used N/C Not Used N/C Speaker -, Left Brown-Gray Speaker +, Left Red-Gray Speaker -, Right Brown-White Speaker +, Right Red-White Video Green Yellow-Green Video Red Yellow-Red Video Sync Yellow-White Video Blue Yellow-Blue Service Credits White-Gray Video Ground Yellow-Black Slam Tilt Black-Green Test Black-Blue Coin 2 Black-Red Coin 1 Black-Brown 2 Start Violet-White 1 Start White 2Up Violet-Black 1Up White-Black 2 Down Violet-Brown 1 Down White-Brown 2 Left Violet-Red 1 Left White-Red 2 Right Violet-Orange 1 Right White-Orange 2 Button A Violet-Yellow 1 Button A White-Yellow 2 Button B Violet-Green 1 Button B White-Green 2 Turbo Violet-Blue 1 Turbo White-Blue Not Used Violet Not Used White-Violet Not Used N/C Not Used N/C Ground Black -5V Ground Yellow-Brown Ground Black —|olalololp|N|<|x<|S}</C)A]o] a] 0) z]/=/-]a}C} rz] m|m|ol/o}a|> Ground Black Solder Sid

Function je of Circuit Board Component Side of Circuit Board

Control Panel Wires That Aren’t Part of Main JAMMA Harness SIO Bd, P7- Function Wire* SIO Bd, P14- 4 Digital Ground 3 Digital Ground Blk +5 Volts +5 Volts Red Unused 3/4/5/15 Unused NC 3/4/5/15 4 Start 3 Start Blu-Wht 4 Stick Up, Bit 0 3 Stick Up, Bit 0 Blu-Blk 4 Stick Down, Bit 1 3 Stick Down, Bit 1 Blu-Brn 4 Stick Left, Bit 2 3 Stick Left, Bit 2 Blu-Red 4 Stick Right, Bit 3 3 Stick Right, Bit 3 Blu-Orn 4 Button A 3 Button A Blu-Yel 4 Button B 3 Button B Blu-Grn 4 Button C, Turbo 3 Button C, Turbo Blu 4 Button D (N/U) 3 Button D (N/U) Blu-Vio *Abbreviations: Bd = Board; NC = Not Connected; Blk = Black; Brn = Brown; Orn = Orange; Yel = Yellow; Grn = Green; Blu = Blue; Vio = Violet; Gry = Gray; Wht = White.

Wiring 5-2

Page 103

Wires That Aren’t Part of Main JAMMA Harness

FunctioniAux Adptr, P1-FunctionWire*SIO Bd, P23-
Digital GroundDigital GroundBik
Output Bit 0Coin 3Bik- Orn
Output Bit 1+5 VoltsRed
Output Bit 2+12 VoltsOrn
Output Bit 3iUnusedKey
UnusedCoin 4Blk-Yel
UnusedDollar BillBlk-Wht
UnusedVolume DownOrn-Red
UnusedVolume UpOrn-Grn
UnusedUnusedNC
UnusedUnusedNC

Unused Function Wire Color*

Unused+12 VoltsOrn
UnusedDigital GroundBlk
Digital GroundDigital GroundBlk
o-+5 VoltsRed

*Abbreviations: Bd = Board; NC = Not Connected; Blk = Black; Brn = Brown; Orn = Orange; Yel = Yellow; Grn = Green; Blu = Blue; Vio = Violet; Gry = Gray; Wht = White. ©]a]N] oa} A]oo|no] =

D.C. Power Source Voltage Limits

FunctionRange LimitsFunctionRange LimitsID
Digital Circuits+4.90V to +5.10V.Audio, Lights-4.75V to -5.25V-5V
Audio, DBV+11.5V to +12.5VNOTE: +5V is adjustable at the Power Supply

Wiring 5-3

Page 104

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 105

CONTROL PANEL WIRING DIAGRAM

ass 55

USER 0 USER 1 USER 2 USER 3

Optical Joystick I40 Board

P2 (OUTPUT) P8 (POWER) P1 (INPUT)

KIT CONTROL PANEL CABLE

22785

Wiring 5-5

Page 106

TO MAIN HARNESS CABL

DIAGRAM OF EXTENSION CABLE FOR 39” VGM

FEW RED BLU.

FOR 39” GAMES ONLY

POD EXTENSION CABLE H-22948

wiYYVC CROT0Of

‘BRN COIN MTR COIN | Door BRN RED com-eTR_2 FUNCTIONS

BRN GRYSpee CeFtcp

ORRNWET She Right SPEAKER r RED WHT +Sokr Right FUNCTIONS

cu a9} PLE TOP Ww EIS SLY Now NU wT RTO? Soe coer no 8 DRED Rcurnu wwe aaa 2 tro Sw a We Ply Sw-B WHT oRv!97 PL yet Tua wit SLU)

poe ister var*714 PLAYER 1

oxo.BLKSy

REF toe Leuve 2.up nu vit aie ]28 {rtve 2 nowN Nu vic_aaN]9? PLYR 2 LEPT_NUL Vio REDIOS CYR 2 RIGHT NUL WIG-CRG PLYe 2 Sw A VIO VEL PLYR 2 Sw_8 VIO GRN Powe 2 TURBO —vig-aLu 8 PLYR 2 Sw 4 WU WI 0 PCYR 2 START —vIo-wHT Oy? PLAYER 2 Sam TT GaN COIN DOOR —seve-cenr oR FUNCTIONS i = ET

VoL_DOW RET 1 UP CRN D HRN,

< Spe Lety RED Ry SPEAKER SiS (eet hen cay FUNCTIONS =She-Riget ian WHT Spar Right RED WHT

a 3 Stan ow 3 Shar ae Pore f PCre 1 DO so] Poe Tee . : PLT RIG PLAYER 1] § 9 Pore ew i 5a ECreT Sot gol FCP TTR 25 FCYET SW no pLve1 START

aL oun 3 Nu pLye 2 up ; ULPCYR 2 DOW é Hac pcve Seer 9| 2 Sve pee na rere > rer PLAYER 2) ¢ dtp ya Ses Soo 3 Shvic-can— pee 2 su 8 hic Ru —pcve 2 TREC joGhvic wu pve 2 ow (Oqryie wa Pore 2 Sta

a 1 TRU NT eee Clg sev NU ALYR 3 DOWN 3 Olbturrea nu _ecve a 4 CleturonG nu eye 3 RIGHT er $6 3| § Smo. sw PLAYER 3] 7 oft ees vn 8 orate TORE 2,Saco-w Sw OTTO WHR Siar

aL Tam 3 Sloe sen nu 3 ote 2 Sfcerep nw cp 4) 2 Sleerorenu PLAYER 4] 6 ottay-ore 3 Steer cew § Steer stu 2, 2}eey Vion Oley WHEN

POWER 394 FOR 30} l40 | of Er

5 oxp 5 Ofte cay — eeu ET P1 ON] $9treteey—oureur-ert igo. | 2¢hetresy—nereurere 05 | Soren —nureuretr BOARD | 2913 oD 76]

2 ssvoc anc Hav DOLLAR | Soe BILL | #9 al Bll $ Sree es ACCEPTOR | ¢ oLRK EL CaN 7 of Bik wH

Reon TOL are Sse uses § Creer ack —JeveaeT bara 1 RN BRNJUYEORT Data 2 opt | 4 opeey bet seven bate 2] JOYPORT| $3 (NOT USED)| 6 ef (NOT USED)] § . He oD

Wiring 5-6 ono. aLK PLY SUP WU aL aL PCY 9 DUWR NUL BLUBRNTOS PCYR 3 LEPT_NU SLU REDO? Byes Riga na scu CRC RENTS? | pave Lewes sya ares [PLAYER 3 raat TR wa) ‘Sw 4 NULL {Oia STARTNU ALU WHT|STt

ee PLYR «UP WU oey BLISS {PLyR = DmuNC NU cey BRN OS Leuye «vert nu. oRy Rea (oS [ety “2 RIGHT NUL cRY oRG | 1 Boyes guy Ne Gey Gee los |PLAYER 4

PLYe_@ Sw 4 WU_GRY VIO PCYR @ STARTNUL GRY -WHITO)!

‘Sin SE] POWER er 385 | FOR

ceaSk—9 |40

{oxo AK taureur-anr-o Eee crv f BuTPUT-eir ver erv 195 | P1 ON thoreuranme sree 193 | Jaq spores | oak pS

syneeepay
HEVICDRE193

@etie3 | DOLLAR

expz3

tenga BILL

toonrome|ACCEPTO!

totem —shewirjos [ACCEPTOR

xp ALK SVD USD — Reo (SGYeORT DATA T—GeRELTS § SEYPORT Data eGR sRNTO ie 83 fyovPoRT HETH95 (NOT USED) weet?

LownaK19,

PANEL CABLE

TO CONTRO!

Page 107

CONTROL WIRING DIAGRAM (49-WAY JOYSTICK)

vee [ye ee ote ye cL Dp oo oir im

BDtoI4
v2Sermon.

= i

vee vee

OF Fos] os

POSITION LOGIC TABLE

DIRECTIONFULLYMODERATELY | SLIGHTLYDEADSLIGHTLY | MODERATELY | _ FULLY
LEFTLEFTLEFTCENTERRIGHTRIGHTRIGHT.
FULLY011101110111001101110001(011100000111110001111110O1tttit1
uP.(00)(01)(02)(03)(04)(05)(06)
MODERATELY | 001101710011001700110001(001100000011710000111110oottt111
uP.(07)(08)(09)(10)(14)(12)(13)
SLIGHTLY000101770001007700010007(000100000001110000011110(00011171
uP.(14)(15)(24)(24)(24)(19)(20)
DEAD000001170000001700000001(00000000(0000110000001110(00001171
CENTER(21)(22)(24)(24)(24)(26)(27)
SLIGHTLY71000117770000177700000714000000110011001100111011001117
DOWN(28)(29)(24)(24)(24)(33)(34)
MODERATELY | 11100111441000111410000114100000111011001110111011101117
DOWN(35)(36)(37)(38)(39)(40)(41)
FULLY111101114411001114110001141100001411110011111110Tt
DOWN(42)(43)(44)(45)(46)(47)(48)
NOTE: 1. Connector pin sequence for the above data is as follows: 9 8 7 6 5 4 3 2 referred to ground at pin 12.
  • Numbers in parentheses are found in the Switch Test. Program does not use the “slightly” positions.

Wiring 5-7

Page 108

CPU BOARD INDICATOR AND SWITCH LOCATIONS

CPU BOARD SWITCH

Switch Location Function Positions State Meaning

Ssi* Edge Near U10 and Resets and 2 Off Normal Operation u12 Restarts Game On Forced Reset

*Notes This switch resets the CPU Board without shutting off power at the power supply.

Wiring 5-8

Page 109

CPU BOARD JUMPER LOCATION TABLE

Jumper J3 J6

Located U28 & U22 & U27 Near... Connector P5

CPU BOARD JUMPER POSITION TABLE

ROM Type | Default Options*

27C080, 1M X 8, EPROM

27C040, 512K x 8, EPROM

27C010, 128K x 8, EPROM

29F040, 512K x 8, Flash

29F020, 256K x 8, Flash

29F010, 128K x 8, Flash

Expansion 27C080, 1M x 8, EPROM (U28) 27C040, 512K x 8, EPROM

27C010, 128K x 8, EPROM

External Boot from CPU ROM Boot Boot from SIO ROM

*Notes 1.-- = Not Applicable

  • Memory type numbers shown are for blank parts. Your game requires programmed parts.

Wiring 5-9

Page 110

CPU BOARD LED INDICATOR STATUS TABLE

Location Function Meaning

Insufficient Power Near U6, U7 & 3.3V CPU

U16 Power On Power OK

Indicator

Blinking Power Supply Fault Off Disk Not in Use

Near U28 & Hard Disk Connector P5 Drive On Locked Up Disk Activity

Blinking Normal Disk Activity

Off* Near U22 & Indicator See Note 3, Below. U26 On*

Blinking* Sequentially

  • LED1 monitors CPU power (+3.3 volts). If his LED is off or blinking, investigate processor circuits. If other LEDs are off or blinking at the same time, check +5-volt circuits or the game power supply.
  • LED2 flashes when the hard disk is operating during game play. LED2 may light continuously during startup. If this LED remains lighted, the hard drive may be locked up or faulty.
  • Software controls RP63. In this game, RP63 initially indicates program startup stages. This LED is a sevensegment, alphanumeric display device. Normally, RP63 displays a lowercase “b,” or an “O” pattern with sequentially blinking segments. During Self-Test screens, RP63 displays a “bouncing bar” that resembles a hyphen (‘-“).

Wiring 5-10

Page 111

SOUND I/O BOARD ASSEMBLY A-23704

Gj fe iS) . — ® & = t i (

mm . 2 3 | 7 qg | 2 3S a 8 3 6 5 _

iE} eo |— T ] E 2 =

qc a . 8 2 5 z oS « A 5 3 5 2 < g 3 = L—_ 7 «| O \ 8 a

& bs = : & a > x

e Bt 4 §

[o3)

o _- ) -_—_ 5 so =—— C LEDS! a = a [ees] 5|\=—

S 9 ro) . 3 Oo © 7 g i i .

v

:

@ LJ

  • | L26 ] - ~ OS a ) @) c

PCI EDGE CONNECTOR

Wiring 5-11

Page 112

SOUND I/O BOARD JUMPER POSITION TABLE *

Location Function Meaning Position

Near U9 & Crystal Y3/O Connector P2Input ModePins 1&2

Output Mode Pins 2&3

Between U35 & U10Video SyncPositive SyncJumper Not

Installed

Negative Sync Pins 1&2

Near U15VO Connector P4Input ModePins 1&2

(Note 2) Output Mode Pins 2&3

J4NoneNoneNot UsedNone
J5Between U15 &/O Connector P4Input ModePins1&2

(Note 2) | Connector P2 Output Mode Pins 2&3

NoneNoneNot UsedNone
NoneNoneNot UsedNone
Between U9 &/O Connector P2Input ModePins1&2

(Note 1) | Connector P4 Output Mode Pins 2&3

Notes

  • Configure I/O port P2 by setting both jumpers J1 and J8 to input or output mode.
  • Configure I/O port P4 by setting both jumpers J3 and J5 to input or output mode.

Wiring 5-12

Page 113

LED SOUND

Location /O BOARD LED INDICATO

Function State R STATUS TABLE

Meaning

LED1 (Note 1) Near U11 Not Used (Remains Off) Off On Blinking

LED2 (Note 2) Near U34 & Crystal Y1 Linking Connector Status Off Not in Use (No Game Linking)

Link Continuity Good

LED3 (Note 2) Near the JAMMA Connector -5V Power Indicator No Power

Normal Operation

LED4 (Note 2) Near U35 & Connector P14 +12V Power Indicator No Power On Normal Operation LEDS (Note 2) Near Connector P23 +5V Power Indicator Off No Power On Normal Operation

LED6 (Note 2) Near U34 & Crystal Y1 CPU Linking Activity Off Not in Use On CPU Communicating with Ethernet Controller

LED7 (Note 2) Near U34 & Crystal Y1 Linking Transmitting Data Off Not in Use (No Game Linking) On Sending Data Blinking Normal Operation

LED8 (Note 1) Near U14 & Crystal Y1 Audio Activity Yellow Off No Sound Boot ROM On Locked Up Blinking Normal Operation LED9 (Note 2) Near U34 & Crystal Y1 Linking Receiving Data Yellow Off Not in Use (No Game Linking) On Receiving Data

LED10 (Note 1) Near U44 & Crystal Y2 Green Not Used (Remains On) Off On Blinking

LED11 (Note 1) Near U44 & Crystal Y2 Red Not Used (Remains On) Off On Blinking

LED12 (Note 1) Near U44 & Crystal Y2 Yellow Not Used (Remains On) Off On Blinking

LED13 (Note 1)

Notes Near U44 & Crystal Y2 Yellow Not Used (Remains On) Off On Blinking

  • Software controls this LED. Indications are game and revision-specific. Changing the EPROMs on this board may alter the function of this LED. Firmware damage may also cause new of different LED behavior.
  • Hardware controls this LED. Indications depend on hard-wired circuitry. A change in normal LED behavior may indicate a circuit fault. Changing the EPROMs on this board shouldn't alter the function of this LED.

Wiring 5-13

Page 114

VIDEO BOARD INDICATOR AND SWITCH LOCATIONS

JL _d J4

Note This video board has no jumpers or LEDs.

Wiring 5-14

Page 115

NBA SHOWTIME Gotp Ebirion/ NFL Bitz 2000 Goin Ebivion

CONVERSION KiT

CHAPTER

SIX

TROUBLESHOOTING

NOTICE: The term VGM refers to the video game machine.

CY CAUTION: This VGM uses complex electronic components that are very sensitive to static electricity. Observe the following precautions before handling VGM electronics. \ Failure to do so may void your warranty and could damage electronic assemblies.

Before servicing electronics, turn off AC power to the VGM. Wait for capacitors to discharge. Before touching or handling electronic assemblies, discharge static electricity on your body. To discharge this static, begin by connecting the line cord to a grounded outlet. Don’t turn on the VGM! Next, touch the safety ground stud of the power supply chassis. Store electronic assemblies in an anti-static area. Use anti-static bags to store or transport VGM circuit boards. Transport the hard drive in its shipping container. Don’t remove or connect electronic assemblies when cabinet power is on. Otherwise, you'll damage electronic assemblies and void the VGM warranty. After you complete maintenance or service, replace ground wires, shields, safety covers, etc. Install and tighten ground and mounting screws.

Troubleshooting 6-1

Page 116

Coin Mechanism and Pricing Troubleshooting Table

accepts currency or tokens, but number of credits per coin or bill is incorrect. SYMPTOM CAUSE REQUIRED ACTION

Improper settings at From Coin Options Menu, choose PRICING ¢ VGM (video game machine) | Pricing Menu OPTIONS MENU. Verify that units and credits are set correctly. Incorrect pulse width on bill validators Consult bill validator manufacturer's literature. Adjust pulse width on validator to long setting. Retest validator operation.

Faulty wiring Check that cabinet wiring is correct for this VGM. Assure that coin meter and coin switches connect properly to control input wires. Faulty coin mechanism Verify that coin mechanism works correctly by testing it in working VGM. If mechanism is bad, replace it.

« VGM won't accept currency or tokens.

¢ —VGM won't start. Improper currency Unlock and open cash door. Empty cash box. Inspect revenue for counterfeit currency. Check vault. Remove any items that block path from mechanism.

« Audio and video are present. Faulty coin mechanism OMRON Unlock and open coin door. Check each mechanism for proper mounting. Remove mechanism. Clear currency path. Reinstall mechanism and latch it. Enter Menu System by pressing and holding TEST MODE switch inside coin door. From Main Menu, choose CONTROLS TEST. Use tests to confirm operation of coin switches.

Tilted coin mechanism or VGM Verify that mechanism is level after doors close. Repair or replace coin door if it is bent or damaged. If necessary, adjust cabinet leg levelers to keep mechanisms vertical. « — Coin indicators don't light Burned-out bulb Burned-out bulbs may appear white or darkened. Check continuity with DVM. Replace burned-out bulb with same type. Open fuse circuit ePaiN Check fuse continuity with DVM. If fuse is blown, replace fuse with same type. If fuse isn't blown, check wiring.

CAUTION: Don’t remove or install any connector when power is turned on. Installation under power will damage the circuit boards or hard disk drive and void the warranty.

Typical Coin Mechanism Mounting

Troubleshooting 6-2

Page 117

VGM Startup Troubleshooting Table

SYMPTOM CAUSE REQUIRED ACTION

« VGM (video game machine) doesn't start.

« VGM appears completely non-functional.

¢ No audio

¢ No illumination

« No video display Power problem Check that VGM power switch is on. Inspect electronics to see if fans are turning. If not: Is power supply connected to its power cable? Is power supply turned on? Plug VGM into AC power outlet. Verify presence of AC line voltage.

Improper line voltage switch setting Turn off VGM power. Unplug AC line cord. Check line voltage switch. If necessary, set it to agree with local AC line voltage. Retest VGM.

Open fuse RON Turn off VGM power. Examine AC fuse on power supply. Examine DC fuses inside coin door vault. Replace faulty fuses with identically rated parts. Turn on VGM power. If fuse opens again, check DC wiring harness and connectors.

Faulty wiring Remove line cord. Test line cord, power plug, and IEC connector for breaks or damage. Verify continuity of each wire in cord. Install cord at power chassis. Press connector firmly to seat it. Check other cables in same manner. Assure that cabinet wiring harness connectors fully seat in corresponding power supply and board connectors. Inspect wiring for breaks or damage.

Faulty circuit boards Turn off power for one minute and turn VGM on again. Power On Self-Test checks electronics. Replace faulty parts and rerun self-test.

Typical Location of Power Supply and Line Cord

Troubleshooting 6-3

Page 118

VGM Startup Troubleshooting Table, continued

SYMPTOM CAUSE REQUIRED ACTION

VGM (video game machine) appears non-functional.

Currency acceptor price indicator is illuminated. Power problem Inspect circuit boards under low-light conditions. LEDs glow if processor circuits receive voltage. Fan should be turning. These indications prove presence of DC from power supply. Still, voltages or signals may not be normal. Turn on VGM power. Using 20-volt DC setting on digital voltmeter, measure DC voltages at power connector pins. Using 2-volt AC setting on digital voltmeter, measure same DC voltages as above. Any reading indicates ripple or noise. In that case, service power supply.

Faulty wiring Turn off VGM power. Assure that wiring harness connectors attach and fully seat onto mating board connectors. Improper jumper or DIP switch settings Verify that circuit board jumpers are set as intended. Check DIP switch settings.

Faulty circuit boards

2. Run power-up self-test sequence. Note errors or failures during tests. Compare LEDs with LED indicator status charts. Note discrepancies. Replace faulty PC boards and rerun self-test.

CAUTION: Don’t remove or install any connector while power is turned on. Doing so will damage circuit boards or hard disk drive, and void warranty.

¢

Front View Of Coin Door

Troubleshooting Interior View Of Electronics

Page 119

VGM Startup Troubleshooting Table, continued

SYMPTOM CAUSE REQUIRED ACTION

doesn't start.

tokens. « VGM (video game machine) | Faulty coin

« VGM accepts currency or

e Audio and video are present. mechanism Unlock and open coin door. Check each currency acceptor to assure proper mounting. Verify that each release latch is closed and locked. Does mechanism accept and reject currency correctly? Test mechanism with good and bad coins. Inspect to see if external acceptor indicators (Pricing, Flashing Arrows, etc.) are lit. Verify that each acceptor operates properly by placing it in working VGM. Replace bad parts.

Faulty switches Enter Menu System by pressing and holding TEST MODE switch inside coin door. From Main Menu, choose CONTROLS TEST. Use tests to confirm operation of each switch. Assure that no loose parts or wires are caught in switch contacts. Check for continuity in each suspect switch connection (Common to Normally Open or Common to Normally Closed). Replace faulty switches (bent levers, broken actuators, etc.).

Faulty wiring Assure that no wires are caught in hinges, latches or switch contacts. Check wiring continuity from circuit board connectors to acceptors. Repair faulty wiring.

Interior View of Coin Door and Cash Door

Troubleshooting 6-5

Page 120

Audio Troubleshooting Table

SYMPTOM CAUSE REQUIRED ACTION

  • From Main Menu, choose VOLUME LEVEL.
«No audioImproper volumeCheck that Attract Music is on (enabled). Verify

setting that all volume levels are set well above zero.

«Video is present2.If necessary, change levels to make VGM

audible.

« VGM (video game machine)1.From Main Menu, enter Diagnostics Menu.
appears to operate normally | Faulty SIO BoardSelectSOUNDSUBSYSTEMTEST.Test

checks entire sound system.

  • Run power-up self-test sequence. Note errors that VGM finds during tests. Compare Sound I/O. Board (SIO) LEDs with LED indicator status charts. Note discrepancies.
  • Verify proper operation of SIO Board by placing it in working VGM. If board is faulty, replace it.
  • Check that cabinet wiring is correct for this VGM.
*Constant low hum from allFaulty wiring2.Verify that cabinet wiring provides separate

speakers. wires (not common return) for each speaker.

  • Check connection of all cabinet ground wires.
  • Repair faulty wiring. Using 2 Volt AC setting on digital voltmeter, Faulty power supply measure voltages at speaker terminals. Any reading indicates ripple or noise. In that case, service power supply.
  • Turn off VGM power. Remove grilles and check
©Audio is distorted, muffled or | Faulty or improperspeakers. Assure that speakers are full range
has missing frequencies.speaker(100 to 10,000 Hz) and rated for at least 20 W.

Woofers must be rated for at least 40 W.

  • Verify proper speaker operation by connecting speaker in question to working VGM. If speaker is faulty, replace it.
1.Multiple-speakerinstallations: © Checkfor

Faulty wiring reversed wires at one speaker. Weak low frequencies and thin or hollow sound quality is symptom of incorrectly phased speakers. Sound tests may not detect this condition, but you can hear it during VGM operation.

  • Repair faulty wiring.
1.FromMain Menu,choose SOUND TEST.
«Dead sound channelFaulty speakerRecheck speakers with audio signals in test.
  • Verify proper speaker operation by connecting speaker in question to working VGM. If speaker is faulty, replace it.
  • From Main Menu, enter Diagnostics Menu.
Faulty circuit boardSelectSOUNDSUBSYSTEMTEST.Test

checks entire sound system.

  • Run power-up self-test sequence. Note errors that VGM finds during tests. Compare circuit board LEDs with LED indicator status charts.
Note discrepancies.
  • Verify SIO Board operation by connecting board to working VGM. If board is faulty, replace it.
  • Verify that cabinet wiring is correct. Assure that Faulty wiring all speakers connect to audio wires. Check for broken or shorted wires.
  • Repair faulty wiring.

Troubleshooting 6-6

Page 121

Joystick Troubleshooting Table

SYMPTOM CAUSE REQUIRED ACTION

Enter game Menu System by pressing and ¢ Players complain that Faulty switch holding TEST MODE switch inside coin door. joystick operates erratically From Diagnostics Menu, choose SWITCH TEST. or unreliably Operate joystick in question. Check for proper readings of up, down, left and right. e¢ Game starts normally 1. Check for wires caught in door hinges, latches or Faulty switch wiring switch contacts.

  • Verify that harness connectors are attached and fully seated.
  • Assure that joystick switches connect properly to control input wires.
  • Reconnect loose cables.
  • Check joystick cable ground connections.
  • Check that cabinet wiring is correct for this VGM (video game machine).
  • Repair faulty wiring.
  • Inspect joystick for: Missing, loose or damaged Faulty mechanical parts, torn rubber T-band, etc. parts 2. Replace bad parts. Clean dust out of optos with swab and cleaner. Dirty optos Don't apply cleaner directly into opto. Never use solvents!
  • Check fuses on 1-40 Joystick Interface Board Faulty joystick fuse inside player control panel. Each joystick has its own fuse.
  • Replace bad fuses.
  • If joystick fuses are okay, install joystick in Faulty joystick working VGM (video game machine) and retest electronics it.
  • _ If joystick still doesn’t work, replace it.
  • If joystick works in second VGM, I-40 Joystick Faulty 1-40 Joystick Interface Board may be bad. Interface Board 2. Replace board and retest joystick.

Joystick Parts

Troubleshooting 6-7

Page 122

Video Troubleshooting Table

SYMPTOM CAUSE REQUIRED ACTION

«Monitor appears nonfunctional

e Audio is present

« VGM (video game machine) controls operate normally Power problem Verify connection of AC Power to video monitor. Inspect CRT neck in dim light. Glowing filament near CRT base proves that some monitor circuits receive power. Still, voltages or signals may not be normal.

Faulty wiring Turn off VGM power. Verify that video signal and Remote Adjustment Board connectors seat properly on Video Monitor Board. Assure that video cables connect to circuit boards. Assure that no wires are caught on chassis or mounting brackets. Improper monitor adjustments Check that BRIGHTNESS (intensity) and CONTRAST are set above their minimum levels. If necessary, adjust these settings.

Faulty monitor circuitry Examine AC line fuse on Video Monitor Board. If fuse is faulty, replace it with identical fuse. If fuse is good: Verify that video monitor operates correctly by placing it in working VGM. If monitor is bad: Check monitor power supply. lf power supply is good: Check monitor horizontal output transistor and related circuitry.

WARNING: HIGH VOLTAGE. VGM monitors generate and store potentially lethal high voltages. Avoid touching any part of the monitor until power has been off for some time. A picture tube can maintain a hazardous charge for up to several days. Only qualified technicians should service monitors. Turn off the power, unplug the VGM and discharge the CRT before attempting service. Even properly discharged tubes can revert to a highly charged state, without reapplication of power.
WARNING: In normal operation, the monitor doesn’t require isolation from AC line voltage. During bench servicing, you may need to operate the monitor outside the cabinet. If you do, isolate the monitor from line voltage with an isolation transformer.
CAUTION: Don’t operate the monitor without the Remote Adjustment Board.

Typical Cutaway Rear View Troubleshooting 6-8

Page 123

Video Troubleshooting Table, continued

SYMPTOM CAUSE REQUIRED ACTION

Game screens don’t appear

No audio

Power-up self-test runs Improper components Verify that hard disk drive is correct for this VGM (video game machine). Label on drive records manufacturer name, assembly number and program version. Verify that circuit boards are correct for this VGM. Label on each board records manufacturer name, assembly number and hardware version. Verify that ROM instruction set is correct for this VGM. VGM set only has one ROM. Label on ROM records assembly number and software version. Replace improper ROMs with correct ones.

Hard drive problems Turn VGM on. Immediately look under hard drive. Hard Drive Activity LED flashes if drive is operating properly. Allow VGM to load normally. Note and record any error messages that occur during self-test. Remove hard drive and install it in working VGM. If symptom recurs there, hard drive is faulty. Replace it.

Blotches of color appear on screen Picture tube aperture mask is magnetized Remove diskettes from room. Demagnetize monitor with external degaussing coil. Take care not to magnetize neighboring VGMs. Monitor may be on or off for this procedure.

White areas in center of screen appear tinged with color

Object edges have fringe of one or more colors Picture tube purity or static convergence is out of alignment Turn on VGM (video game machine). Press and hold TEST MODE to enter Menu System. At Main Menu, select Monitor Tests Menu. Run through Crosshatch, Red, Green and Blue screens to find clearest display of problem. Display screen with greatest problem. Display Crosshatch Screen. Locate purity and static convergence ring magnets on back of monitor neck. Watch screen in mirror. Adjust magnets to minimize problem. Follow instructions from monitor manufacturer. Display Crosshatch Screen. Touch up adjustments while watching screen in mirror.

Background of Attract Mode screens seems out of sync

Words on screen read OK Medium resolution monitor, and DIP switch set for low resolution Press and hold TEST MODE to enter Menu System. At Main Menu, select Diagnostics. Then select DIP Switch Tests Menu. Locate DIP switch bank U12 on the Sound I/O Board. Turn off switch 2. Reenter Attract Mode and check screens.

CAUTION: Don’t operate the monitor without its Remote Adjustment Board.
WARNING: HANDLE FLUORESCENT TUBE AND CRT WITH CARE. If you drop a fluorescent tube or CRT and it breaks, it will implode! Shattered glass can fly eight feet or more from the implosion.

Troubleshooting 6-9

Page 124

Video Troubleshooting Table, continued

SYMPTOM CAUSE REQUIRED ACTION

White areas at screen edges appear tinged with color

Dots at screen edges appear oval or cylindrical Picture tube dynamic convergence is out of alignment Have service bureau dynamically reconverge monitor. This procedure requires removing and repositioning yoke. Service bureau must follow instructions from monitor manufacturer.

Video tears or rolls, or has black bar down middle of screen

Video may appear as colored bars of dashed lines Improper sync signals Check to see if Video Board puts out type of sync that your monitor requires. Adjust sync for monitor you're using: On SIO Board, set DIP switch bank U12, switch 2. Off = medium resolution (default); on = low resolution. Verify that jumpers are set correctly for monitor. If necessary, add or remove video sync jumper at Sound I/O Board jumper block J2. With no pins connected (or pins 2 and 3 connected), board outputs positive sync. With pins 1 and 2 connected, board outputs negative sync.

Faulty wiring

Checkconnectorsandcablesforwiring

continuity. Video cables connect graphics card to circuit boards, and then to video monitor. Assure connection of all cabinet ground wires, especially at video monitor chassis. If you find faulty wiring, repair it.

Faulty monitor circuitry Check video monitor operation by connecting it to working VGM (video game machine). Assure that monitor is correct type for this VGM. Monitors with wrong resolution can’t lock sync. If you have wrong type monitor, replace it. Electromagnetic fields

Movecabinetfarawayfrommachines,

appliances, or competitors’ VGMs. Missing colors Faulty wiring

Checkconnectorsandcablesforwiring

continuity from circuit boards to video monitor. Repair faulty wiring. Faulty monitor color drive circuitry Verify that video monitor operates correctly by connecting it to working VGM.

One color is dimmer or brighter than others

Whites appear tinted everywhere on screen Maladjusted color bias pots BONS

Da Turn on VGM (video game machine). Enter Monitor Tests Menu. Watch Color Bars screen in mirror. Adjust three bias pots for best colors. (Most monitor neck boards include these pots.) Also check White Screen. Touch up controls. If whites still seem tinted, have service bureau rejuvenate picture tube.

Picture is dim or faded Maladjusted BRIGHTNESS pot or subnormal picture tube emission Watch Color Bars screen. Adjust BRIGHTNESS and CONTRAST pots for greatest number of grays. You'll find these pots on Monitor Remote Control Board, behind coin door. If pots have no effect, have service bureau rejuvenate picture tube.

Troubleshooting 6-10

Page 125

Video Troubleshooting Table, continued

Picture is too narrow Maladjusted WIDTH pot Enter Monitor Tests Menu. Watch Crosshatch Screen while adjusting WIDTH pot for best picture. You'll find this pot on Monitor Remote Control Board, behind coin door.

Picture is too short Maladjusted HEIGHT pot or damaged vertical circuit Enter Monitor Tests Menu. Watch Crosshatch Screen while adjusting HEIGHT pot for best picture. You'll find this pot on Monitor Remote Control Board, behind coin door.

  • __ If pot has no effect, service vertical output circuit. Enter Monitor Tests Menu. Watch Crosshatch
¢Picture seems shifted to one | MaladjustedScreen while adjusting HORIZONTAL POSITION
sideHORIZONTALpot for best picture. You'll find this pot on Monitor

POSITION pot Remote Control Board, behind coin door.

  • Substitute working yoke.
¢Keystone-shaped pictureShorted turns in yoke | 2.Have service bureau converge monitor.

3.__ Retest monitor.

Software Update Troubleshooting Table

SYMPTOM CAUSE REQUIRED ACTION

Update didn’t work You skipped steps or performed them out of sequence. Return update components to kit, reinstall original parts in cabinet, and try process again.

eAfter update procedure,Installation error may | 1.Inspect for bent or broken pins.
screen reports lower thanhave damaged2.If you have another kit, try it.
latest versiondevice.3.Ask your distributor to check your floppy disk.
  • Once you've updated disk drive, CPU
«No Attract Mode screensMismatched bootinstructions must be at correct version to make

update version and use of new data stored on disk. Be certain that

©Board indicators illuminate,hard drive.boot ROM device resides in proper socket.

i is completely 1. Install disk ROM. Only use upgrade socket for

You may have hard disk drive updates. During game play, installed devices in upgrade socket must be empty.

wrong sockets.2.Load ROM contents onto drive.
  • Remove ROM from game.

NOTICE: Someday, software updates for your VGM (video game machine) might become available. These upgrades may improve your VGM’s performance or add new VGM features. Such upgrades tend to appear sometime after factory first releases VGM. Contact your distributor for information about updates.

Troubleshooting 6-11

Page 126

Miscellaneous Problem Troubleshooting Table

SYMPTOM CAUSE REQUIRED ACTION

«Marquee lamp is intermittent or non-functional

« VGM (video game machine) starts and plays normally Faulty fluorescent tube Remove fluorescent tube from its sockets. If you find cracks or darkened ends, install new lamp. Clean tube. Check continuity of both fluorescent tube filaments. Verify that fluorescent tube operates by placing it in working VGM. Faulty lamp fixture Verify that lamp pins make good connection with socket contacts. Check ballast for continuity. Faulty wiring Measure fluorescent lamp AC voltages. Check wiring and connector continuity from AC power chassis to lamp assembly. If you find faulty wiring, repair or replace it.

« VGM operates normally

  • Cabinet becomes warm after several hours of use Obstructed fan Check bottom and rear of cabinet for blocked airflow. Move VGM away from sources of heat. Turn off VGM power. Remove dust from vent holes with high-power vacuum cleaner. Faulty wiring Check fan wiring and connectors. If you find faulty wiring, repair or replace it. Faulty fan Check operation of all fans, including power supply fan. If fan is faulty, replace it.

« Error messages appear on screen Faulty hardware Check any assembly (RAM, ROM, Battery, etc.) identified in error messages. Replace faulty parts. Call your authorized distributor for help with unresolved screen messages.

Troubleshooting

Fan Location and Mounting

6-12

Page 127

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 128

WARNINGS & NOTICES

WARNING e — Use of non-Midway parts or circuit modifications may cause serious injury or equipment damage! e Use only Midway authorized components and parts. Failure to do so will void your warranty and may result in incorrect or unsafe operation. Substitute parts or modifications may void the EMC directive or FCC type acceptance. « Federal copyright, trademark and patent laws protect this game. Unauthorized modifications may be illegal under Federal law. The modification ban also applies to Midway game logos, designs, publications and assemblies. Moreover, facsimiles of Midway equipment (or any feature thereof) may be illegal under federal law, regardless of whether or not such facsimiles are manufactured with Midway components.
WARNING Prevent shock hazard and assure proper game operation. Plug this game into a properly grounded outlet. Do not use a cheater plug to defeat the power cord's grounding pin. Do not cut off the ground pin.
WARNING: A small portion of the population has an epileptic condition that may cause seizures. Affected persons experience seizures while watching some television pictures or playing certain video games. People who have not had seizures may still have an undetected epileptic condition.

If anyone in your family has experienced epilepsy symptoms (e.g., seizures or loss of awareness), consult your physician before using video games.

While children play video games, a parent should observe. Be alert to the following symptoms: Dizziness, altered vision, eye or muscle twitching, involuntary movements, loss of awareness, disorientation, or convulsions. If you or your child experience these symptoms, discontinue use immediately and consult your physician.

NOTICE This kit has been tested. It complies with limits for a Class A digital device, under FCC Rules, Part 15. These limits provide reasonable protection against harmful interference when the equipment operates in a commercial environment. This equipment generates, uses and can radiate radio frequency energy. If not installed and used according to the instruction manual, this equipment may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference. If interference occurs, the user must correct it at his own expense.

CAUTION Installation of this kit does not guarantee compliance with FCC requirements. You are solely responsible, and Midway has no responsibility for FCC compliance of installed kits. Don’t install an FCC compliance label on the product until the FCC acknowledges compliance.

NOTICE You may not reproduce any part of this publication by mechanical, photographic, or electronic means. You may not prepare phonograph recordings of this document. You may not transmit this publication or otherwise copy it for public or private use, without permission from the publisher.

COPYRIGHT & TRADEMARK NOTICE Entire contents of this manual copyright © 2000 Midway Amusement Games, LLC. All rights reserved. The following are trademarks of Midway Amusement Games, LLC: Midway®, SportStation™, NBA Showtime™, NFL Blitz 2000 Gold Edition™ ©2000 NBA. © 2000 NFLP. Team names and logos are trademarks of indicated teams. The NBA logo is a trademark of the National Basketball Association. Officially Licensed Product of the National Basketball Association. The NFL shield, Super Bow! and Pro Bowl are trademarks of the National Football League Players. The Players Inc. logo is a registered trademark of the NFL Players. The NBC logo is a registered trademark of the National Broadcasting Company.

FOR SERVICE Call your Authorized Midway Distributor.

MIDWAY AMUSEMENT GAMES, LLC 3401.N. CALIFORNIA AVE., CHICAGO, ILLINOIS 60618-5899 USA