CATHODE RAY TOMES

Gravitar Black Widow Retrofit TM-232 1st Printing

Gravitar (version 3) (Atari, 1982) · Technical Manual · 24 pages · 13 sections · original scan

Page 1

TM282 ‘4st Printing

| GRAVITAR™ RETROFIT

Instructions

ATARI, INC. | 720 SYCAMORE DAVE i P.O. BOX + MILPITAS, “Sugar 95035 ATARI 408/942-3100 * TELEX 35-7488.

| amor Communicators Company

Page 2

If reading through this manual does noi lead tc soiving 4 certain maintenance problem, cail EHELP® at the Atari Customer Service office in your geographicai area, as shown below.

WEST and CENTRAL U.S.A. Parts and Service

Atari, Inc. Califomia Customer Service Cfice 1705 N. Fair Oaks Avenue >. 0. Box 427, Sunnyvale, CA 94086 Telex 17-1103 (Monday-Friday, 7:30=4:00 em Pacific Time) From California, Alaska, or Hawaii 2 (408) 745-2900 ge Service from anywhere in the area shown in white ‘= tollstree (800) 538-1671

EAST U.S.A.

Service only

Atari, Inc, New Jersey Customer Service Office 12A World's Fair Drive, Somerset, NJ 08673 Telex 37-9347 (Moncay-Friday, 7:30-4:00 pm Eastern time) From New Jersey @ 205) <s0-s008 age 70M anywhere else in this area 9 toll-free (800) 526-3849.

EUROPE

Parts and Service

Atari Ireland Limited European Customer Service Office Ticoerery Town, Ireland Telex 28165 TIPPERARY TOWN, (Monday-Friday, 9:00-8:00 pm GMT) IRELAND

BZ 062-62155

Page 3

Gravitar™ Retrofit Instructions

Introduction

The following information includes the necessary retrofit instructions for changing the Gravitar upright game into a Black Widow game. The modifications include changing the cabinet graphics, the control panel, the hamess assembly, certain game board components, and the self-test label. Information is also provided for changing the Gravitar Schematic Package Supplement (SP-206) to reflect the Black Widow circuitry.

Kit Parts Inventory

Check the contents of the Black Widow Retrofit Kit (A040037-01) before proceeding with the retrofit procedure. Note that the integrated cirauit (IC) components included in the retrofit kit are labeled with their respective part numbers. The parts included in this retrofit kit are listed in Table 1.

Table 1 Retrofit Kit Contents

Part No. Quantity Description

A040039-01avElectronics Kit—Includes the following:
110000-223a22 kh, 45%, 1/4 W resistor
128002-1011100 pF, 100 V fixed mica capacitor

136017-101 to -110 10 , Integrated circuits

A039975-011Control panel with decal
A039989-01yjControl panel harness assembly
A039990-011Main conversion harness assembly
A040040-011Attraction glass assembly
ST-234-011Self-test chart
™H234aBlack Widow Operators Manual
62-0392SPDT momentary pushbutton start switch with

red light-emitting diode

75-01083#10 flat washer
75-5112B810-24 x 3/4-inch black carriage bolt
75-9418810-24 hexagonal locknut
036895-012Black molded switch bezel

(continued on next page)

Page 4

Table 1 Retrofit Kit Contents (continued)

Part No. Quantity Description

039978-011Left side-panel decal
039978-021Right side-panel decal
040002-011Printed-circuit board (PCB) label
171021-00128-position joystick

Tools Required for Retrofit

The tools listed in Table 2 (or their equivalents) are required to perform a complete retrofit modification.

Table 2 Tools Required for Retrofit

QuantityDescriptionPurpose
1L1/8-inch Allen wrenchInstall attraction glass
13/8-inch hex-nut driverAssemble control panel
17/16-inch hex-nut driverInstall control-panel
1Diagonal cuttersRemave PCB components
%Needle-nose pliersInstall PCB components
afPhillips-head screwdriverRemove access panel and PCB
116-27 W soldering ironInstall PCB components
1SqueegeeInstall decal graphics

Retrofit Instructions

NOTE

These procedures mist be performed by qualified service personnel.

The following procedures are arranged in a sequence reccmmended for performing the retrofit modification. The parts of the Gravitar game that are affected by the modification (see Figure 1) are removed first. Next, the game PCB is modified. Then, the modified PCB and the remaining kit parts are installed.

Page 5

Attraction Glass Assy.

Decals Right & Lett Side

Game PCB See Figure 2

Main Hamess See Figures 3 & 4

Control Panel Assy. ‘See Figure 3

Biack Widow version.

Figure 1 Location of Gravitar Parts Affected by Retrofit

Page 6
WARNING

Unplug the game before performing the following procedures.

Remove the Attraction Glass

1. Use the 1/8-inch Allen wrench to remove the three screws and washers that fasten the top retainer to the cabinet. Remove the retainer. Keep the screws and washers for reassembly.

Loosen the three screws that fasten the bottom retainer to the cabinet. Remove the attraction glass.

Remove the three screws and washers from the bottom retainer. Keep the screws and washers for reassembly.

Remove and discard the foam tape from the underside of the top and ‘bottom retainers. Keep the retainers for reassembly.

the Control Panel

Use the Phillips-head screwiriver to remove the screws that fasten the access panel to the back of the game cabinet. Remove the access panel. Reach inside the game cabinet and release the two spring-draw latches on the back of the control panel.

Grasp the top edge of the control panel from the front of the game

cabinet and swing the panel down to expose the three mounting bolts.

Disconnect the cable connector at the back of the control panel.

Use the 7/16-inch hex-nut driver to remove the Gravitar control panel from the cabinet. Keep the bolts, washers, and nuts for reassembly.

the Game PCB

Disconnect the two edge connectors from the game PCB.

Use the Phillips-head screwdriver to remove the screw and spacer that

secure the game PCB to the cabinet. Keep the screw and spacer for

reassembly.

Carefully slide the PCB straight out of its slots. Be careful not to twist the board to avoid loosening connections ar components.

Page 7

Modify the Game PCB

NOTE

‘The game PCB must be removed from the cabinet before performing this procedure.

a Remove the 10 integrated circuits (EPROMS) from the locations shown in Figure 2.

  • Install the 10 integrated circuits from the retrofit kit in the PCB locations shown in Table 3. Refer to the part numbers labeled on each IC and use Figure 2 to determine their locations.

Table 3 IC Component Locations

IC Part No. Location’

136017-101 DL 136017-102 E/Fl 136017-103 HL 136017-104 JL

136017-105 K/LL 136017-106 ML 136017-107 L7 136017-108 M/NT 136017-109 N/P7 136017-110 RT

NOTE

Refer to Figure 2 for the locations of the components removed and replaced in steps 3 through 5.

  • Use the diagonal cutters to remove capacitors C28 (0.001 uF) and C34 (0.22 uF). These components are not used in the Black Widow game.
Page 8

Figure 2 Location of PCB Components Affected by Retrofit Replace Label “Floplace these integrated circults with those from the retrofit kit that have part numbers as shown in each focation.

Page 9

5. Use the soldering iron and needle-nose pliers to remove capacitor C27 (0.001 uF) and resistor R46 (10 Ki). Replace C27 with the 100 pF capacitor and R46 with the 22 kt resistor from the kit. Be careful not to overheat the PCB. Excessive heat can separate the conductive material from the board.

Remove the protective backing and attach PCB label (040002-01).

Page 10

Assemble the Control Panel

NOTE

Refer to Figure 3, Assembling the Control Panel, when performing the following procedure.

Insert the two black molded switch bezels into the two holes on the left front of the control panel. Make sure the switch bezel tabs are inserted into the hole slots.

Hold the bezels in position and hand-tighten the two pushbutton start switches into the bezels.

Insert the 8-positicn joystick handles through the control panel. holes and use the 3/8-inch hex-nut driver to attach the carriage bolts, flat washers, and hexagonal locknuts.

Connect the wire harness leads to the pushbutton start switches and joysticks. The lead pairs to each joystick switch can be attached to either terminal.

Peel the protective backing from the l-inch wire hamess cable mounts and firmly attach the wire harness to the control panel.

Attach the ground clip to the control-panel latch bracket so that the clip contacts rest in the clean unpainted area on the bracket.

Install the Wiring Hamess

1. Insert the four wires from the main conversion harness assembly into the pin sockets of the 44-pin PCB edge connector as shown in Figure 4. Make sure the contacts are positioned properly before locking the pins in place.

Use five wire ties from the retrofit kit to secure the four harness assembly wires to the existing Gravitar min wire harness that runs underneath the game PCE and toward the control panel.

Page 11

@Position Ground Clip

Figure 3 Assembling the Control Panel

Page 12
NOTE

Insert new pins with spring contact facing center of connector.

Figure 4 Hamess Wire Installation

Page 13

Install the PCB

a, Carefully slide the modified game PCB into its mounting slots. Make sure the foam pad is secured to the cabinet near the center of the PCB.

Z Attach the PCE to the cabinet with the screw and spacer.

  • Connect the two edge connectors to the PCB. Make sure the PCB is inserted firmly against the back of the connectors.
  • Secure the edge connectors to the PCB by fastening a wire tie around

the eye at each end of the two connectors and through the hole in the

PCB as shown in Figure 5 (total of four ties).

il

Page 14

Figure 5 PCB Edge-Connector Wire-Tie Installation

Page 15

Install the Control Panel

A Securely fasten the Black Widow control panel to the game cabinet with the three mounting bolts, washers, ani nuts previously removed from the Gravitar control panel.

2: Securely fasten the two comectors at the back of the control panel to their mating connectors on the main hamess assenbly.

  • Close the control panel. Reach into the back of the game cabinet and fasten the two spring-draw latches at the top edge of the control panel.

Install the Attraction Glass

  • Loosely fasten the bottom retainer to the game cabinet with the three mounting screws and washers.
  • Slide the Black Widow attraction glass into the bottom retainer.
  • Hold the top retainer tight against the top of the attraction glass and securely attach the top retainer to the game cabinet with the three mounting screws and washers.
  • Press the bottom retainer tight against the attraction glass and tighten the three mounting screws.

Install the Decals

NOTE

We recommend that the following installation procedure be performed by two persons. One person may have difficulty handling the cabinet and the large decals.

bs Tip the game cabinet sideways and gently lay it on a soft blanket.

  • Thoroughly clean the side of the game cabinet to ensure the removal of all dust.

Eu Grasp the top edge of the appropriate decal for the side of the game cabinet. Hold the decal up off the floor and peel away the protective backing.

  • Gently lay the decal, sticky side down, in the center of the game cabinet. Position the decal to allow about three-quarters of an inch between the edges of the decal and the edges of the cabinet.
Page 16
NOTE

‘The adhesive side of the decal has glass beads that will permit positioning of the decal. DO

NOT PRESS DOWN on the decal until it is in

position or the glass beads will break and set the adhesive.

5. With the decal down and in position, use the squeagee to break the

glass beads and set. the adhesive by quickly working from the center to the outside edges.

  • When the wrinkles are removed and the decal is in position, gently tum the game cabinet over to the opposite side. Be careful to avoid damaging the freshly applied decal.
  • Repeat steps 1 through 6 for the remaining decal.
  • Carefully raise the cabinet to the upright position.
  • When both decals are firmly affixed, remove the protective covering. Allow time to dry before proceeding!

Change the Model Number

Permanently mark the game identification serial number label (see Figure 1) with model number 33100-01.

Install the Self-Test Chart

Replace the Gravitar self-test chart on the inside of the rear access panel with the Black Widow self-test chart.

Set the Option Switches

1, Set the option switches as described in the Black Widow Operators Manual.

  • Replace the rear access panel on the game cabinet.

Perform a Self-Test

lL. Plug the game in.

2 Set the power on/off switch to the on position.

Page 17

EP Perform the self-test procedure as described in the Black Widow game manual. Be sure to adjust the x- and y-axis potentiometers as described on sheet 8B in the Gravitar Schematic Package Supplement.

Change the Gravitar Schematic Package

The circuitry given in the Gravitar Schematic Package Supplement, SP-206, applies to the Black Widow game after the following changes have been made:

® Sheet 18, Gravitar Main Wiring Diagram: Replace the Control Panel section of the wiring diagram with Figure 6.

® Sheet 5A, Gravitar PCB Schematic Diagram: Replace the Option Switch Input, Audio Output, and Coin Door and Control Panel Input schematics with Figures 7 and 7A.

© Sheet 5B, 6A, 6B, 7A & 7B, Gravitar PCB Schematic Diagrams: The signatures shown in color do not apply for the Black Widow game.

@ Sheet 11A, Gravitar PCB Troubleshooting: Replace the Memory Map with Figure 8.

© Sheet, 11B, Gravitar PCB Troubleshooting: Replace Table 4, Player and DIP Switch Inputs, with Figure 9.

© Sheet 128, Gravitar PCR Troubleshooting (2nd printing only): Delete Troubleshooting with Checksums procedure.

Page 18

Pesa J24A,

To P2O-8 FIRE UP aa TO P2O-K FIRE DOWN enc] =| [ex 70 P20-$ FIRE LEFT rarips TO PaO-L FIRE RIGHT

Figure 6 Sheet 1B (Gravitar Main Wiring Diagram) Changes

Page 19

Figure 7 Sheet 5A (Gravitar PCB Schematic Diagram) Changes

Page 20

Coin Door and Control Panel Input

aah Lees i pur EEF ont

ornen 22ee
oremreeee
gsnndresoe
°eR,aAtea
moveurfferaTry owae
move nicHT £3raeoebee

queda delsh Repepepes BE ee ee nett et

Figure 7A Sheet 5A (Gravitar PCB Schematic Diagram) Changes

Page 21

Figure 8 Sheet 11A (Gravii itar PCB Troubleshootit ing) Changes S/PRSEEER De>eer eoccece beane> eacoccs bearer eooneae Pepper ensoose peer er anes cette pppere > prprre Drree peorrr be>eee been ee borer ‘AIS At ATS AI2 ANI AN AD_AB_AT AS AS MAAS AZ AT AD

Sa8n888

goucc000G eoecc0ess eo00000000 eovoveve09 go0cc0000 oouvcce000 soncc9000 saga g MEMORY MAP

Page 22

Table 4 Player and DIP Switch Inputs

ADDRESS INPUT SWITCH TEST RESULTS

7800Right coin switch,DATA dispiay changes when any

Left coin switch, coin switch or the Self-Test Auxiliary coin switch,| switch is activated. Upper nyb- Self-Test switch ble of DATA dispiay is unstable.

* 8000Left JoystickDATA display changes when any

of these input switches is activated.

8800Right JoystickDATA display changes when any

Start 1 of these input switches is ac- Start 2 tivated.

Figure 9 Sheet 11B (Gravitar PCB Troubleshooting) Changes

Page 23

Pres ARISES BS a nt 4) ist SARS

Warranty

Seller warrants that its printed-circult boards and parts thereon are free from defects in material and workmanship under normal use and service for a period of ninety (20) days from date of shipment. Seller warrants that Its video displays (in games supplied with displays) are free from defects in material and workmanship under normal use and service for a period of thirty (30) days from date of shipment. None of the Seller's other products or parts thereof are warranted. If the products described in this manual fail to conform to this warranty, Seller's sole liability shall be, at its option, to repair replace, or credit Buyer's account for such products which are retumed to Seller during said warranty period, provided: {e)Seller is promptly notified in writing upon discovery by Buyer that sald products are defective; (b)Such products are returned prepaid to Seller's plant; and (©)Selier’s examination of said products discloses to Seller's satisfaction that such alleged defects existed and were not caused by accident, misuse, neglect, alteration, improper repair installation, or improper testing. In no event shall Seller be liabie for loss of profits, loss of use, incidental or consequential damages. Except for any express warranty set forth ina written contract between Seller and Buyer which contract supersedes the terms herein, this warranty is expressed in lieu of all other warranties expressed or implied, including the implied warranties of merchantability and fitness tor a particular purpose, and of all other obligations or liabilities on the Seller's part, and it neither assumes nor authonizes any other person to assume for the Seller any other liabilities in connection with the sale of products by Seller ae ie & > d ‘

‘

The use of any non-Atari parts may void your warranty, according to the terms of the warranty. The use of any nor-Atari parts may also adversely affect the safety of your game and cause injury to you and others, Be very cautious in using nor-Atari-supplied components with our games, in order to insure your safety. Atari distributors are independent, being privately owned and operated. in their judgment they may sell parts or accessories other than Atari parts or accessories. Atari cannot be responsible for the quality, suitability or safety of any non-Atari part or any modification including labor which is performed by such distributor.

Page 24

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.