Gauntlet Dark Legacy 27in
Gauntlet Dark Legacy (version DL 2.52) (Midway Games, 1999) · Manual · 61 pages · 50 sections · original scan
- Use of non-Midway parts or circuit modifications may cause serious injury or equipment damage! Federal copyright, trademark and patent laws protect this game. Unauthorized modifications may be illegal under Federal law. The modification ban also applies to Midway Games Incorporated and game logos, designs, publications and assemblies. Moreover, facsimiles of Midway equipment (or any feature thereof) may be illegal under federal law, regardless of whether or not such facsimiles are manufactured with Midway components.
Tf you or anyone in your family has experienced symptoms linked to an epileptic condition (e.g. seizures or loss of awareness), immediately consult your physician before using any video games.
We recommend that parents observe their children while they play video games. If you or your child experience the following symptoms: dizziness, altered vision, eye or muscle twitching, involuntary movements, loss of awareness, disorientation, or convulsions, DISCONTINUE USE IMMEDIATELY and consult your physician.
COPYRIGHT & TRADEMARK NOTICE. You may not reproduce any part of this publication by mechanical, photographic, or electronic means. You may not produce phonograph recordings of this document. You may not transmit this publication or otherwise copy it for public or private use, without permission from the publisher.
For Service: Call your Authorized Midway Games West Inc. Distributor.
©1998, 1999 Midway Games West Inc. All rights reserved. MIDWAY?® is a trademark of Midway Amusement Games, LLC. Used by permission. GAUNTLET® DARK LEGACY™ is a trademark of Midway Games West Inc.
675 sycamore drive
milpitas, california 95035
http://www.midway.com bmn
GAUNTLET
Operations Manua
Setup + Service + Sy
The manufacturer intends that any federal, state or local law o operators of this game are resp turer's factory settings for this g specific jurisdiction. It is the op to make the appropriate adjust
675 syca
Setup
ce NOTICE: Information in this manual may change without notice. Midway Games West Inc. reserves the right to make improvements in equipment function, design, or components as progress in engineering or manufacturing methods may warrant.
Chapter | Setup
Safety Notices
The following safety instructions apply to all operators and service personnel. Specific warnings and cautions appear throughout this manual. Read this page before preparing your game for play.
NOTICE. Ensure proper mating of all connectors. If a connector does not slip on easily, do not force. Reversed connectors may damage your machine and void the warranty. Connectors are keyed to fit specific pins on each board.
EPILEPSY WARNING
‘A very small portion of the population has a condition which may cause them to experience epileptic seizures or have momentary loss of consciousness when viewing certain kinds of flashing lights or patterns that are present in our daily environment. These persons may experience seizures while watching some kinds of television pictures or playing certain video games. People who have not had any previous seizures may nonetheless have an undetected epileptic condition.
If you or anyone in your family has experienced symptoms linked to an epileptic condition (¢.g., seizures or loss of awareness), immediately consult your physician before using any video games.
Parents should observe their children while they play video games. If you or your child experience the following symptoms: dizziness, altered vision, eye or muscle twitching, involuntary movements, loss of awareness, disorientation, or convulsions, DISCONTINUE USE IMMEDIATELY and consult your physician.
Product specifications Chapter 1 Setup
Operating Requirements Electrical Power Temperature Humidity
| Domestic 120VAC @ 60Hz 3.0 Amps | 37°F to 100°F | Not to exceed 95% rela- |
| Foreign 230VAC @ 50Hz 2.0 Amps | (3°C to 38°C) | tive |
Japan 100VAC @ 50Hz 3.0 Amps
Cabinet Statistics
| Shipping Dimensions | Shipping Weight | Design Type |
Width 28.5 in (72.4 cm) Depth 43.5 in (111 cm) Height 74.0 in (188 cm) 486 Ibs (221 kg) Dedicated video game machine with 49-way optodetector joysticks
Equipment Characteristics
Video Display Monitor Medium resolution RGB 27 in (68.5 cm) CRT Audio System 2 channel audio 2 full range speakers Currency Acceptors Standard coin door 2 coin mechanisms, DBV ready 1 coin counter
Game Characteristics
Player Variables 1 to 4 players per game High score recognition Operator Variables Coinage, game options, difficulty, volume, demo mode, audits, statistics Diagnostics Automatic power-up test Manual multi-level Menu System
MAINTENANCE
Viewing Glass
You need not switch off AC power to clean the glass. Apply a mild glass cleaner to a clean cloth or sponge, then use this to wipe the viewing glass. Do not apply cleaner directly onto glass. Liquid could drip down into video game machine circuits or onto detectors and cause erratic operation.
Cabinet
Use plastic-safe non-abrasive cleaners to avoid damage. Apply cleaner to clean cloth or sponge, then use this to wipe the controls or cabinet. Do not apply cleaner directly on controls or cabinet.
Chapter 1 Setup
INSTALLATION AND INSPECTION
Remove packing material and set control panel box aside. Inspect cabinet exterior for signs of damage.
- KEYS Reach down through control panel opening into front of cabinet and remove keys from hook on coin door. Unlock and open coin and cash box doors. Electrical cords, spare parts, levelers, mounting hardware, tools, and other items are packed in cash box.
- Move cabinet to intended location. Ensure vent holes at rear of cabinet are not blocked or next to heat registers. Adjust leg levelers as necessary to stabilize cabinet and raise wheels above floor. Distribute weight equally on each corner Use cabinet in fixed position only.
LEG LEVELER ~N\Z STATIONARY CASTERS & CABINET WELDMENTS
- SHOWN FOR REFERENCE
CASTERS AND LEG LEVELERS UNDER CABINET
- CONTROL PANEL Place carton containing control panel on floor face down. Open container carefully and remove packing material. Inspect control panel for signs of damage.
- Lift control panel assembly from box and set on its front side. Remove wing nuts from bolts protruding from underside of control panel and retain them for reinstallation.
SPACER TUBE
CONTROL PANEL TOP. g
AND HOUSING Ne CORNER PAD Ne :
CARTON CORNER PAD
BOTTOM PAD
CENTER PAD
CONTROL PANEL HOUSING ASSEMBLY PACKAGE
Chapter 1 Setup
- Reach into control panel from underside and open latches that hold control panel top to control panel housing. Leave panel closed until it is installed on cabinet.
- Place control panel assembly on cabinet ledge. Slide control panel housing toward monitor. Align gasketed control panel bracket with bottom of viewing glass.
- Lift control panel and hold it open. Align mounting screw holes in control panel box with those in cabinet. Use four 4-20 hex-head bolts, flat washers, and lock washers in spare parts kit to secure control panel to cabinet. Tighten bolts firmly.
- Remove retaining clip at bottom center of the viewing glass. Reinstall screw in mounting hole. Keep clip with spare parts for reinstallation when relocating cabinet.
- WIRING Mate control panel wiring harness connectors with main wiring harness connectors. Attach control panel ground wire to hinge assembly with wing nut. Close control panel. Reach up through open coin door to secure and fasten latches at sides of control panel.
- Reach through coin door and locate threaded ends of control panel attachment bolts. Install a wing nut on each bolt where it protrudes through control panel housing into cabinet. Hand-tighten nuts snugly.
- MARQUEE Locate T-27 tamper-resistant fastener wrench in spare parts kit. Remove and retain screws and washers from either side of top of cabinet. Pivot marquee lightbox assembly upright. Reinstall screws and washers through top of cabinet into lower lightbox holes. Do not overtighten screws.
TOP RETAINING STRIP MARQUEE LIGHTBOX ASSEMBLY
7 CONTROL PANEL TOP. HOLE FOR UPRIGHT POSITION
HOLE FOR LAYDOWN POSITION
CARRIAGE BOLT : a
FLAT WASHER ™ \
TAMPER RESISTANT ———~ SCREW WING NUT
MACHINE SCREW
RETAINING CLIP LOCK WASHER
FLAT SHEET METAL WASHER’
SCREW
CONTROL PANEL HOUSING
CONTROL PANEL AND MARQUEE SETUP
Chapter | Setup
- ELECTRONICS Remove rear door. Inspect cabinet interior for signs of damage. Check all major assemblies to ensure secure mounting. Clear path to allow open airflow from fan.
- SECURITY To install an extra padlock to secure the rear door, remove lock bracket nuts from inside cabinet. A hasp is attached inside cabinet above rear door. Reverse hasp on bolts so it protrudes through slot in back of cabinet. Reinstall nuts. Hold shackle guard in place over hasp when installing lock. Order an extra shackle guard and install it over the game electronics hasp for additional security.
CARRIAGE BOLT FLANGE GRIP NUT KEPS NUT PADLOCK BRACKET <2 FLAT WASHER
KEY LOCK BRACKET aan PLATE
A csamsce BOLT A J SHACKLE GUARD
HASP BRACKET AND LOCK PLATE ASSEMBLY INSTALLATION
- AC POWER Find the power cord in the spare parts kit. Match holes on IEC plug with the prongs in receptacle and push firmly to seat line cord. Route cord away from areas of foot traffic.
pe aeaeterty
oN LINE CORD
LINE CORD INSTALLATION
- Refer to Main Cabinet Wiring Diagram on page 51 and check that all cable connectors are correctly secured. Inspect for damaged connectors. Avoid forcing connectors or reversing connections.
- Plug line cord into grounded (3-terminal) wall outlet. Switch AC power on using the ON/OFF switch on the power supply. The game powers up and begins self-diagnostics. If there are no errors, Attract Mode begins.
- POP For added visibility, slide the POP display artwork (“Check Me Out”) into the plastic holder.
- Remove adhesive backing from bottom of holder and center on top of marquee top retaining strip. Or remove center screw on top of retaining strip and remove adhesive tape from bottom of holder. Slide holder under retaining strip. ON/OFF SWITCH
GAY een Tr
Service
ce NOTICE: Information in this manual may change without notice. Midway Games West Inc. reserves the right to make improvements in equipment function, design, or components as progress in engineering or manufacturing methods may warrant.
Chapter 2 Service Only qualified service personnel should perform maintenance and repairs. Product guidelines apply to all game operators and service personnel. Specific notes, cautions, and warnings abound throughout this manual where applicable. Read the safety pages before beginning service.
This video game machine uses complex electronic components that are very sensitive to static electricity. Observe and follow these precautions prior to handling the game electronics: ¢ Ensure AC power is turned off prior to servicing electronics.
- Discharge any static electricity build up in your body by first touching the metal power supply chassis. Do this before touching or handling the electronic assemblies. Store electronic assemblies in an anti-static area. Use anti-static bags to store or transport hard disk drive, CPU Board Assembly, and all other electronics.
- Do not remove or connect electronics with AC power on, as this will damage them and void the warranty.
- Always replace ground wires, shields, covers, etc., when maintenance or service is completed.
Marquee
Remove tamper-resistant screws and washers at either side of cabinet. Lower marquee lightbox assembly backwards to a horizontal position. From rear of machine, remove three hex-head sheet metal screws holding marquee retaining strip to cabinet while holding strip in place. Restrain glass when removing strip to avoid breakage. Remove strip and set aside. Lift marquee glass, plastic channel, and artwork out of groove and set in safe place. Do not cross-thread screws during re-installation.
Fluorescent Lamp and Starter
Lower marquee as described above. Remove retaining strip, glass, and artwork. Turn tube a quarter turn and pull from sockets. Starter also requires quarter turn for removal or installation. Carefully place new tube into socket and rotate quarter turn to reinstall. Clean tube to remove fingerprints and dust.
Fluorescent Light Assembly
Lower marquee as described above. Remove retaining strip, glass, and artwork. Disconnect power cable from fluorescent light assembly. Loosen but do not remove fasteners holding assembly to cabinet. Remove ground wire. Slide assembly slightly forward to disengage screws from keyholes. Lift out assembly.
Chapter 2 Service Control Panel Switches
Unlock and open coin door. Reach through door and remove wing nuts. Release toggle latches. Open control panel. Label and disconnect wires. Separate switch from its button housing. Bend large prong away from switch just enough to slide switch off housing. Unscrew switch mounting nut and pull entire button assembly out toward front of control panel.
Coin Counter
Unlock and open coin and cash doors. Meter is in a lower corner of door opening. Record meter count before testing or replacing. Disconnect wiring harnesses and ground wires to coin mechanisms. Reach through coin door and locate meter wires. Disconnect wiring at connector. Remove coin door mounting screws. Remove coin door assembly from cabinet and set it on a work surface. Remove meter mounting screws from front. Ensure replacement unit has a diode across the terminals. Remember to reconnect wiring harnesses and ground wire upon reinstallation.
a RETAINING STRIP
f 7 A BACKLIT MARQUEE MARQUEE GLASS
SPEAKERS.
CRT GLASS
VIDEO MONITOR
CRT BEZEL
CONTROL PANEL
o “ DBV COVER PLATE
COIN DOOR
FRONT VIEW OF CABINET
Gauntlet: Dark Legacy ll
Chapter 2 Service Monitor Bezel
Unlock and open coin door. Reach through door and remove attachment bolt wing nuts. Release toggle latches. Open control panel. Push viewing glass up just enough to swing it out of the cabinet and then pull it out and down to remove it. Grasp monitor bezel at bottom and lift it out of groove.
-D\ age with an isolation transformer.
Monitor
Unlock and remove rear door. Disconnect monitor from wiring harness and ground wires. Unlock and open coin door. Reach through door and remove attachment bolt wing nuts. Release toggle latches. Open control panel. Remove viewing glass and monitor bezel. Remove four 4-20 flange nuts securing monitor mounting flanges to mounting panel. Pull monitor carefully from cabinet and set aside.
To install a different monitor, remove three 3/8-16 hex bolts from bracket at bottom of monitor. Install bracket and bolts onto bottom of new monitor. Slide bottom of monitor into cabinet and tilt it up from the top. Replace flange nuts at top of monitor, and screws on outside of cabinet.
Power Supply
Switch off AC power. Remove screws, then unlock and remove rear door. Unplug the IEC AC connector from rear and DC connector from top of supply. Remove two top and two bottom screws holding supply to power chassis, then lift off chassis. Note voltage setting.
To reinstall supply, remove voltage switch cover if necessary and set voltage to correct value. Set supply on chassis and align mounting holes. Install four screws and two power connectors.
Chapter 2 Service REAR VIEW OF CABINET (30046)
an FLUORESCENT LAMP ASSEMBLY
HANDLE PULL VENT
ELECTRONICS ASSEMBLY
POWER SUPPLY ASSEMBLY
Ne LINE CORD
LOWER CABINET VENTS.
REAR DOOR ASSEMBLY
CPU Board Assembly
Switch off AC power. Open rear door. Remove metal electronics cover. Carefully note orientation of JAMMA connector and other cables. Extract harnesses and hard disk drive ribbon cable from board connectors. Remove groundplane mounting screws and security lock. Slide entire electronics assembly toward rear of cabinet and lift to remove it. Set electronics assembly in a static-free place. Disconnect VGA connector. Remove security mounting bolts and screws connecting circuit boards to groundplane. Carefully remove Sound I/O Board, pulling gently to disconnect PCI edge connector from CPU Board. Set Sound I/O board in a static-free place. Carefully remove CPU Board, pulling gently to disconnect it from Video Card. Use anti-static bags and protective containers from new parts to store board if it is not reinstalled.
Chapter 2 Service Hard Disk Drive
Switch off AC power. Unlock and remove cabinet door. Remove electronics cover. Disconnect DC power cable from hard disk drive. Unplug ribbon cable from hard drive and leave it attached to CPU board. Carefully remove screws and lift drive assembly out of cabinet. Store drives in anti-static bags or approved shipping containers.
SHIELDED VIDEO CABLE
HARD DISK DRIVE RIBBON CABLE VIDEO CARD BRACKET HARD DISK DRIVE POWER CABLE FAN ASSEMBLY
HARD DISK DRIVE ASSEMBLY
VIDEO CARD ASSEMBLY
CPU ASSEMBLY SOUND I/O ASSEMBLY
FERRITE BEAD 1-1/4
ELECTRONICS ASSEMBLY
Sound I/O Assembly
Switch off AC power. Open rear door. Remove electronics cover. Carefully note orientation of JAMMA connector and other cables. Extract harnesses and hard disk drive ribbon cable from board connectors. Remove groundplane mounting screws and security lock. Slide entire electronics assembly toward rear of cabinet and lift to remove it. Set assembly in static-free place. Remove security mounting bolts and screws connecting circuit board to groundplane. Carefully remove Sound I/O Board, pulling gently to disconnect PCI edge connector from CPU Board. Use anti-static bags and protective containers from new parts to store board if it is not reinstalled.
Chapter 2 Service Video Card
Switch off AC power. Remove rear door. Remove Electronics Assembly cover. Disconnect VGA connector. Remove screws holding the Video Card to groundplane. Carefully slide Video Card away from CPU Board, disconnecting PCI edge connector. Use anti-static bags and protective containers from new parts to store the board if it is not reinstalled.
Battery
Switch off AC power. Remove rear door. Remove Electronics Assembly cover. Hold battery edges and pull up firmly to remove. When installing new battery, note position of keyhole in socket. Replace only with same or equivalent type recommended by manufacturer. Dispose of used batteries according to instructions on battery package.
Memory
The ROM (Read Only Memory) circuits contain game operating instructions. Switch off AC power. Carefully note position, then remove using a chip extraction tool.
To reinstall, orient chip over its socket and press firmly to seat pins. Do not force.
CARRIAGE BOLT -“GROUNDPLANE (REAR VIEW) LOCK HASP (PART OF GROUNDPLANE)
KEPS HEX NUT SHACKLE GUARD
WOOD BARRIER PANEL (FRONT VIEW)
Game Electronics Security
The shackle guard shipped with cabinet is intended for use on rear door. An additional guard may be used to safeguard game electronics.
Gauntlet: Dark Legacy 15,
Chapter 2 Service
Memory Replacement
The ROM (Read Only Memory) circuits contain game operating instructions. Memory devices are especially sensitive to static charges. Use grounding precautions when handling these parts.
Switch off AC power. Unlock and remove rear door. Remove electronics cover. Carefully note each IC position, then remove them using a chip extraction tool. To reinstall memory circuits, orient chip over socket and press firmly to seat pins. Do not force.
Dollar Bill Validator
(Use MARS AE2411-U3 ULL. Recognized currency changer) Install dollar bill validators or other currency acceptors with the additional wiring connector. Switch off AC power and unplug line cord. Unlock and open coin door. Read door label for additional information. Disassemble validator and remove material to fit it inside coin door as illustrated, then reassemble unit.
Remove nuts, spacers, and cover plate from door. Change switch settings or make adjustments before mounting the unit. If the manufacturer has supplied an adapter plate, place it over the door cutout at this time. Install spacers on threaded studs, then align the validator mounting holes with the studs and seat the unit in the door opening. Install the nuts and tighten firmly. Attach the ground wire (green with yellow stripe) lug to the door ground stud next to the hinge. Mate the wiring harnesses and press to fully seat connectors. Route wires away from door edges and hinge. Inspect for proper bill chute alignment. Plug in the line cord and turn on the game. Change the mechanism setup and pricing, then test known good and bad bills to verify proper operation. Close and lock the coin door when correct. Reverse these steps to remove a validator for service or replacement.
DOLLAR BILL VALIDATOR
GAU sen Tr
CHAPTER
System
ce NOTICE: Information in this manual may change without notice. Midway Games West Inc. reserves the right to make improvements in equipment function, design, or components as progress in engineering or manufacturing methods may warrant.
Chapter 3 System STARTING UP
Each time the game is first turned on or power is restored, it begins executing code out of the boot ROM. These self-diagnostic tests automatically verify and report condition of the hardware and the disk drive. The screen is blank during these tests. If any of the individual tests fails, then an error message will be displayed for each test. The message will be displayed for 30 seconds or until any button is pressed. ¢ Ifno buttons are pressed, the system will quickly complete all tests then load and run the game.
- Press and hold the TEST button inside the coin door to skip the boot ROM tests and activate the Menu System.
Once all Power-up tests have been passed, the game goes into Attract Mode. Scenes and sounds from a typical game are alternated with previous high scores in an endless pattern until game play starts.
Insert currency to start game. Play begins after a mission is chosen. The game progresses until time runs out. If no more play is required, the game automatically returns to the "attract mode".
GAME RULES
Play instructions are on information panel between speakers. Up to four players at a time can explore a world, facing hordes of monsters, searching for treasure, avoiding traps, finding and using magic, and adventuring their way to the exits.
Players choose from eight characters (and, later, eight alternate characters) to face the hordes of monsters. that have overrun the land of Gauntlet. With more than 100 unique monsters and 10 intimidating boss characters, players have their hands full, defeating each of the eight world bosses and collecting keys before meeting the demon Skorne. Following Skorne’s defeat, players must defeat him yet again in an underworld level, after which they face the evil overlord Garm. Numerous power-up enhancements are scattered throughout the land to help players get to the finish.
Players can save their character with player IDs. One password saves all eight different characters. During game variable selection, players simply enter their initials and their own 3-letter player ID that they choose. The characters, with their experience levels and current ratings for strength, speed, toughness, and magic are automatically saved along with any Rune Stones players find.
To access the alternate characters, players first build characters to level 10. Depending upon which character they have played, they then can choose to play as the Minotaur (Warrior), Falconess (Valkyrie), Jackal (Wizard), Tigress (Archer), Hyena (Jester), Ogre (Dwarf), Medussa (Sorceress), and Unicorn (Knight).
To defeat Garm, players must find all 13 Rune Stones and defeat Skorne twice. Three Stones are hidden in each world. Upon finding a Stone, a character is saved permanently with a password.
There are over 35 unique special weapons found throughout the game that will help players in their quest. These power-ups are found in chests and barrels, in nooks and crannies, and even in plain view and can be bought with gold in the Shop.
Chapter 3 System INDIVIDUAL AND MULTIPLE PLAY
Insert currency to start game. Select a joystick/button combination and press START. Select a password, character, and journey. In multi-player games the first to select a journey determines everyone’s path. Onscreen life counters decrease as characters are wounded until they reach zero, at which point the player must deposit more coins to continue. You can continue playing after others drop out. When coins are inserted, the character joins in the middle of the action.
PLAYER CONTROLS
START buttons let players begin or continue play and also select items from the service menu.
FIGHT/MAGIC/TURBO Buttons attach enemies. Players access special turbo movies by pressing TURBO and FIGHT at the same time when their "fight bar" has been charged up.
Magic is used by pressing TURBO + MAGIC and FIGHT + MAGIC during game play.
Between levels, players redeem accumulated gold for valuable power-ups and things that will enhance their characters like strength, toughness, speed, and magic.
JOYSTICKS advance a character along a journey and select items from service menu.
PLAYER 3. PLAYER 4 PUSHBUTTONS, REI PLAYER 2 PUSHBUTTONS, BLUE
PLAYER 1 PUSHBUTTONS, YELLOW_-/
VA START
PLAYER CONTROL LOCATIONS
Chapter 3 System
OPERATOR CONTROLS
Operators have lock-and-key access to the menu system for statistics, adjustments, and testing to prevent tampering. On-screen messages guide the operator through menu options.
Cabinet Switches
The Power Switch (located on the power supply at the rear of the cabinet) turns off the game during service. It does not reset the game variables.
Monitor Remote Adjustments
The Monitor Remote Adjustment Board (located just behind the coin door) sets the video display for optimum viewing.
Control Switches
Volume Down and Volume Up Buttons (mounted on a bracket behind the coin door) increase or decrease game sound levels.
For greater profits, adjust volume levels to a loud setting to draw attention to this game.
Test Mode Button The Test Mode push-button switch enters the menu system. Press the Test Mode button briefly to run automatic tests. To make changes, press and hold Test until the system menu is displayed.
Service Credit Button: this button allots credits without changing the game's bookkeeping total.
These buttons may also be used instead of the control panel buttons and joystick when operating the menu system.
SERVICE VOL. VOL. TEST CREDIT DOWN UP MODE
~ TEST SWITCH BRACKET
Chapter 3 System
MENU SYSTEM
SYSTEM OVERVIEW
Game variables and diagnostics are presented in a series of on-screen menus. The Main Menu allows you to view information, change or verify equipment operation. Submenus display further choices, after which more data appears or tests run. Use both operator and player controls to navigate menus and start or stop routines.
SCREEN LAYOUT
The color bar at the top center of each screen displays the current menu title. The center of the screen holds data (menu items, video signals, statistics, reports, etc.) The bottom of the screen contains messages (control functions, revision levels, etc.).
ORGANIZATION
Main Menu screen items are either options or tests. Submenu screen items offer choices within a category. A Menu may have zero, one, or several Submenus. You can always return to the previous menu, and often advance to the next menu. Detail Menu screen items contain specific information. You interact with the system to get results or to make changes.
Use the indicated control to highlight an item. You can only select one highlighted at a time. To return to game play, select EXIT TO GAME, then press the indicated button.
TYPICAL SELECT TEST MENU SCREEN
Chapter 3 System
ADJUST VOLUME
You can adjust Attract Mode volume independently of Game volume. Use the joystick to raise or lower volume level. Music plays continuously while setting volume.
VOLUME ADJUSTMENT MENU SCREEN
Use the Player 1 START button to choose Game or Attract volume adjustment. When the selected variable flashes, use the joystick to change the level.
Game volume adjusts from zero to maximum. The game seems more realistic if players experience loud sounds during play. These weapons do not have silencers.
Attract volume is continuously adjustable from Mute (zero) to maximum. For greater profits, make Attract Mode loud to draw attention to Gauntlet: Dark Legacy.
You adjust Attract and Game volume levels independently, but Attract cannot be louder than Game volume. If you try this, Attract level automatically lowers proportionately. Lowering Attract level does not affect Game setting.
Volume level is represented a bar made of dots. The longer the bar, the higher the volume.
Press the Player 2 START button after making volume adjustments. The Player 1 START button cancels your recent changes and returns both levels to what they were before you touched them.
Chapter 3 System
STATISTICS
The Statistics report allows the operator to assess how well the game is being played. In addition to the earnings, various game aspects are tracked to determine the player skill levels.
Statistics may be reset to zero or allowed to increase after each viewing.
STATISTICS REPORT MENU SCREEN
The illustration shows how the report screen looks after the game is reset or is first turned on. Most statistics increase in value as the game is played. It is normal for some values to remain at zero: for example, the Aux Coins count will not change unless an additional Currency Acceptor has been installed in the game, and the Error Count will not change if no errors have occurred.
Low counts in both coin and player statistics may suggest the game is too difficult for the skill levels of the players at this location; high continue counts may indicate the game is too easy. Difficulty level and other play characteristics may be adjusted from the Game Options menu.
Record statistics before performing service or making repairs on the game.
Press Player 2 START or service credit button to view system errors, which tell you the status of the hardware. Press Player 2 START again, and you will see user messages. Press Player 2 START again and you will see histograms. Press Player 2 START again to see level histograms.
Press both START buttons to cancel settings on screen and return all counts to factory default values.
The HISTOGRAMS screens will have no bar graphs until the system has enough data to plot.
The USER MSGS screen will contain no messages until the system detects an error.
Chapter 3 System
GAME OPTIONS
These adjustments allow you to customize the game. Each variable changes an aspect of game appearance or play. Optimum settings cause high player interest and increase earnings.
Use the joystick to select a menu item and to view the range of choices or change their value. Options may be reset to factory defaults or changed after each viewing.
GAME OPTIONS MENU SCREEN
Factory defaults are displayed in green text.
The illustration shows how this report screen looks after game is reset or first turned on. Use joystick to advance variables through range of choices. Some items have more options than others. View all options before selecting one.
The effects of these options can be judged by comparing statistics reports before and after changes were made. As players become more familiar with the game, new features or increased difficulty will make the game challenging and continue to generate interest.
Difficulty adjusts the level of play difficulty. It ranges from easiest to hardest in several steps. Default is Medium.
Health Per Credit determines amount of health credits added to the timer each time a player uses a credit by pressing the START button. It ranges from 300 to 1000. Factory default is 500.
Blood controls whether blood and gore appear on screen when a character is killed. Factory default is ‘Yes.
Chapter 3 System Freeplay Demo Mode incre: the maximum number of health credits allowed on the health timer per game credit beyond normal game limits. Factory default is Off.
Health Decrease Timer sets the speed of the Health timer. It ranges from Off to Fast in several steps. Factory default is Normal.
Texts In selects the language of the on-screen announcements and hints. Selection of a different language changes the player information presented only on the screen. It does not change any of the voice announcements, menu screens or tests. Factory default is English.
Reduce Hints sets the frequency of visual and verbal assistance to a player during the game. Yes decreases the frequency of hints. Factory default is No.
Audio Mode sets the audio output of the game. Use Stereo for cabinets with more than one speaker. Use Mono for cabinets with a single speaker. Factory default is Stereo.
Audio in Attract sets the frequency of game play instructions while the game is idle and in Attract mode. It ranges from Never to Always. Factory default is Often.
Cabinet Type configures the number and type of inputs for the cabinet. Factory default is 4 Players 1 Cabinet.
Allow Password controls whether the game will save a player's character experience with a three-digit password for later games. Factory default is Yes. Take special caution before changing this setting, as many registered players invest much time and money into building up their characters, which can only be accessed with passwords.
Contest Enabled allows Midway sponsored T-shirt promotion. Players who defeat Garm by collecting all 13 rune stones and winning the final battle are eligible for an "I Beat Garm" T-shirt. Factory default is Yes.
Codes Enabled allows use of secret codes. Factory default is Yes
Clear Password files controls password file deletion. Set this feature to Yes to delete all saved character experience and passwords. Factory default is No.
Auto Clear Highscores sets whether the game will automatically reset the high score table from time to time. Factory default is No.
Restore Factory Game Options resets the Game Options. Set this option to Yes to reset the game to factory default options. Factory default is No.
Record the High Scores before making any option changes to the game.
Chapter 3 System
COIN OPTIONS
PRICING OPTIONS
Use the Player 1 joystick to select menu items, view the range of choices, and change values. Options may be reset to factory defaults or changed after each viewing.
PRICING OPTIONS MENU SCREEN
Custom pricing sets credits required to start and continue a game, rewards for buy-in and winning, etc. Factory default are shown above. View all choices before selecting, as some items have more options than others. Free offers no options. Free game incentives may reduce earnings.
Chapter 3 System
COIN OPTIONS
PRICING OPTIONS
Mech setup permits operators to add or remove coin or bill mechanisms. Values are shown for all devices, but changes to unused inputs have no effect if the mechanism is not in the game.
MECH SETUP MENU SCREEN
The two DIP switches located at U13 and U12 on the SIO Board configure the Electronics Assembly for various input and output devices. The on screen display shows the switch status for easy reference. See Wiring Chapter for specific information on the function of switch positions.
Chapter 3 System
These tests allow the operator to manually check each switch in the game.
Use the joystick to select the Controls Test. Press Player 1 START button to begin test. Activate each switch and the indication on the screen changes state. Release the switch and the indicator returns to its previous normally open or closed condition. Test switches in any combination.
CONTROLS TEST MENU SCREEN
Each switch change should be exactly duplicated by a single indication on the menu screen. The alphanumeric indicators next to each joystick should display three distinct settings as the stick is moved in each direction toward its outermost limit.
Player Controls Tests verify crossed wires, intermittent conditions, and stuck switches.
OPERATOR CONTROLS are shown on screen under the MISC heading. Each switch change should be exactly duplicated by a single indication on the menu screen.
Operator Controls Tests verify crossed wires, intermittent conditions, and stuck switches.
Coin and Cabinet Switches are shown on the screen without regard for their actual game location. Each switch change should be exactly duplicated by a single indication on the menu screen.
Chapter 3 System
SOUND TESTS
These tests verify the proper connection and operation of the audio components. There are no custom settings or variables in these tests, which are performed automatically.
MENU SCREEN
SPEAKER TEST sends alternating voice sounds to the left and right speakers. Voices should be clear and distinct from each other. Each voice must come from the location identified. Refer to ADJUST VOLUME screen if necessary to increase loudness for this test.
The Speaker Test screen verifies crossed connections, incorrect phase, and distortion. Press the Player 2 START button to end the Audio Speaker Test and return to the SOUND TESTS menu.
AUDIO HARDWARE TEST REPORT SCREEN
AUDIO HARDWARE TEST automatically tests the electronic components of the audio amplifier for problems and reports the results as "passed" or "failed." Each "failed" result should be noted and referred to qualified service personnel. This test also shows the revision numbers for the audio EPROMs and other components. Press SERVICE CREDIT to return to the SOUND refer to the Troubleshooting Chapter.
Chapter 3 System
MONITOR TESTS
Monitor Tests provide patterns to verify monitor performance or make adjustments. Gauntlet: Dark Legacy uses a medium-resolution monitor. Other monitors may cause poor performance.
Use the joystick to select a menu item. Press the Player 1 START button to begin the test. Once the menu is open, use the joystick to select an option, and the Player 1 START button to begin it. Use the Player 1 START button to select various elements of each test. Press the Player 2 START button to return to the Monitor Tests menu screen.
MONITOR TESTS
COLOR BARS
CONVERGENCE
PURITY
To select test, Use joystick To run test, press P1 START or TEST To return to menu, press P2 START or CREDIT
MONITOR TESTS MENU SCREEN
COLOR BARS fills the screen with shades of colors to verify red, green, blue and white level dynamic adjustments. Each bar should appear sharp, clear, and distinct from bars on either side.
Borders must be visible on top, bottom, and sides of screen. Bars should not change screen position or color as the background or border are removed or restored from the video display.
Color Bars screen is useful in adjusting the monitor brightness and contrast.
CONVERGENCE tests fill the screen with a grid and a series of dots. Grid and the dots should be all one color, with no fringes or parallel images. Lines should be straight and dots round.
Borders must be visible on top, bottom, and sides of screen. Lines and dots should not change position or color as background or border are removed or restored from video display.
Convergence tests are useful in verifying the monitor convergence, linearity, and dynamic focus.
PURITY tests fill the screen with 100% of the chosen color at normal intensity. Each screen should be uniform from top to bottom and side to side. No retrace lines or noise should be visible.
Borders must be visible on top, bottom, and sides of screen. Image color should not change position or color as the background or border are removed or restored from the video display.
Purity tests help verify monitor intensity, black level, blanking and automatic degaussing.
Chapter 3 System
DISK TESTS
These verify Hard Disk Drive functions. Some files can be repaired. These tests are automatic and the results appear on the menu screen as they occur. There are no custom settings or adjustable variables in these tests. The Player 2 START button aborts the tests.
DRIVE READ TEST MENU SCREEN
Hard Drive Connected test verifies interface between CPU Board Assembly and Hard Disk Drive. The processor requests disk information. Data cannot be retrieved if there is a problem.
Drive ID is an industry standard identification for Hard Disk type and capacity. This is a manufacturer hardware number only; it does not identify software or program stored on drive assembly.
Logical Sector Test performs a sector by sector read/verify test on the drive. As the status of each block of sectors is checked, the speed of data transfer is compared to its acceptance limits.
Tests Completed These tests run over and over. The number increases each time the test cycle repeats (approx. every 5 minutes). After at least one cycle ("pass") is complete, note any errors and press the Player 2 START button to end the test.
FILE SYSTEM TEST SCREEN
Checking File performs a file by file check of data stored on the hard disk drive and reports its findings. If there are errors, the system tries to fix them (approx. 5 minutes per cycle). The system reports on the severity of the errors and advises if they will affect game performance.
Chapter 3 System
SET RTC
Use this menu to set the correct time and date for your location.
SET RTC
Date: day mo date year Time hr min
SET RTC MENU SCREEN
SWITCHES AND JUMPERS
The CPU and Sound I/O Boards have several hardware variables that can be changed to adapt this assembly to other uses. Jumpers activate circuit paths, and DIP switches select instructions.
Switches
The CPU Board Assembly has one pushbutton switch, which resets the CPU Board and restarts the game without turning off AC power. There are two DIP switches on the Sound I/O Assembly at U12 and U13. See Wiring Chapter for further explanation.
Jumpers
Jumpers control signals to other components in this game. These signals match production audio amplifiers, speaker system, and video monitors.
Active circuit paths are factory optimized during the board test procedure. Leave jumpers in original positions to avoid program error messages.
Errors
The system detects errors at startup or during diagnostic tests and reports them on screen. The system automatically repairs errors such as minor disk data faults. Fix other errors, such as player control calibration, by manually resetting values in game memory. Gauntlet: Dark Legacy generally continues to operate (but with reduced performance) after discovering minor errors.
Record error messages before attempting to correct a problem. The USER MESSAGES report may store additional temporary messages (refer to STATISTICS earlier in this chapter).
After recording messages, turn off AC power, wait a few minutes, then turn AC power on. Pay attention to the startup screens and note any error messages during Power On Self Tests. If possible, enter the SELF TEST MENU SYSTEM and run all tests related to where errors occurred. Record and compare any new messages to the previous ones to determine whether errors are random or chronic.
NOTICE. Do not ignore error messages even if you can start and operate the game. Poor performance in caused by playing games with errors may reduce earnings.
CHAPTER
Parts
ce NOTICE: Information in this manual may change without notice. Midway Games West Inc. reserves the right to make improvements in equipment function, design, or components as progress in engineering or manufacturing methods may warrant.
Chapter 4 Parts
CABINET FRONT VIEW (30046)
31-3505 UPPER DECAL, BEZEL—
03-9764 RT BEZEL —— 01-14878 TOP RETAINER — Fah tad ‘. ALT MARQUEE ~ A-23643 LIGHTBOX —— 31-3506 ASSEMBLY LOWER DECAL, BEZEL, 08-8196 4H BLANK MARQUEE i GLAS 4020-01070-20 1/4-20x1-1/4 4H
08-8197.1 4701-00005-00 cRT GLASS —I Lw 1/4 SPLIT
4700-00034-00 \—FW .265x.875x.067
@ MOUNTING 5675-15355-00 RACKET MONITOR PANEL ASSEMBLY TAIL DRAWING) 04-12935 | ae REENED Oahe 4408-01128-00 NUT 8-32 KEPS.
4308-01123-16B —BOLT #8-32x1 Ca
01-14886-1
R/UNDER COIN DOOR EE APPLICATION CHART D OETAIL DRAWING)
—04-11229-1 FRONT PANEL Cl
WARE NOT SHOWN:
4010-01007-08 = MS. 0-32x1/2 P=PH 4020-01100-32 TR 1/4 20x2 BH CS 4106-01001-10 = SVS f6x5/8 2-PH 4106-01115-20 SMS fl6x7—1/4 PL—-HWH-A 4420-01141-00 = \UT + /4~20 FLANORP. 4420-01119-00 = NUT 1/4—20 ESN/NE 4320-01123-20B 0.1 1/4 20x11 /4 CB 4320-01123-28 © 30.7 1/4—20x1-3/4 CB 4320-01 123-40B 20x2-1/2 CB 4700-00032-00B 4700-00139-00 250%.03
Chapter 4 Parts
CABINET REAR VIEW (30046)
31-3581 SCREENED
20-10482 RUBBER BUMPER
4410-00129-00. -_ NUT 10-32 KEPS
20-10480 STARTER
08-7377 —/ EVELER DETAIL DR INSTALLAT
02-4404 CASTER SHAFT /— STAND, EXTENDED S$ 20-10412
AND. ADHESIVE
FLUORESCENT LAMP ASSEMBLY (SEE DETAIL DRAWNG))
_-=~ 24-8809 FLUORESCENT BULB,
—— 4310-01136-12B BOLT 10-32x3/4 CB
08-8326 HANDLE PULL VENT
~ 4108-01219-11 SCREW #8x11/16 PH AB-SPCL
A MBLY (SEE DETAIL DRAWING)
POWER SUPPLY ASSEMBLY || AND MOUNTING BRACKET (SEE DETAIL DRAW!
(SEE APPLICATION CHART)
| 4108-01115-20B j SCREW #8x1- =HWH ——
01-9359
- WHEEL BRACKET
20-8712-37 “"E" RING 3/8 SHAFT
9627 WHEEL
REAR DOO (SEE 0
Chapter 4 Parts
REAR DOOR LOCK ASSEMBLY (A-22403)
,— 01-8989
/ 01-7264 RETAINER PLATE
_» 4410-01129-00 NUT 1 KEPS UNF
20-10350 DOOR LOCK CAM ASSEMBLY
4700-00129-00 FW. .203x.468x.030 ———~ 4310-01136-20B 10-32x1-1/4 CB
01-14877 —_— LOCK PLATE
4420-01141-00 4320-01123-20B AGE BOLT FLANGE GRIP NUT——~ 4410-01129-00 KEPS NUT
4700-00129-00 01-11286 tie
PAD LOCK B 01-14877 LOCK PLATE 01-11287 / K BRACKET —“ 4310-01136-20B -— CARI E BOLT S 01-14882 LE GUARD
Chapter 4 Parts
CONTROL PANEL AND HOUSING ASSEMBLIES (A-23603)
20-10209-4 A-23605 PUSHBUTTONS N CONTROL PANEL ASSEMBLY
01-14879 SS RETAINER ——\
A-21939-1 49-WAY JOYSTICK AS: DECAL OVERLAY
20-10209-3 4108-01199-10B PUSHBUTTONS, BLUE —\ 20-10209-5 ; = PANEL HINGE RR 20-10209-1 16-8587-583 PUSHBUTTONS, RED GROUND STRAP
4322-01124-128 4108-01219-11 BOLT 3/8-16x8 #8x11/16 PINHD
4308-01123-16B BOLT 8—32x1 ¢ 20-10483 STAMPED STEEL NU — a INN 4700-00032-00 01-11955 Xe SSC FLATWASHER .265%.625 LATCH BRACKET __ fy r YX 4701-00005-00 4408-00128-00 : HER 1/4 SPLIT
NUT 8-32 KEPS 4020-01070-24 \— SCREW 1/4-20x1-1/2 HH
4408-00128-00 \— NUT 8-32 KEPS
04-12934 EENED HOUSING
04-11235-1 —— PANEL HOUSING FRONT 01-14884 CORNER BRACKET
31-3502-3 “—— DECAL, CONTROL PANEL FRONT
20-10484 WINGNUT ——J A-23604 CONTROL PANEL HOUSING ASSEMBLY
Chapter 4 Parts 49-WAY JOYSTICK ASSEMBLY (A-21939-1)
04- 10849- 1 — JOYSTICK
) CONTROL PANE HOWN FOR RE
03-9656 COVER SLIDE
JOYSTICK TOP
4700-00129-00 FLATWASHER .203x.468x.030 —— 17-1129 ¥ CENTERING GROMMET
4410-01129-00 HEX NUT 10-32 KEPS PINHO-A8._ SPC
o9-8411.24 |
a 20-8712-25 RING 1/4"
03-8412.1-4 OPTO BREAKER SLIDE, LONG
03-8420 i A ~ OPTO BOARD SLIDE RETAINER fl i u OPTO BREAK! & I ~ Lato. 01211-28 #8-10x1-3/4 FH PH PLASTITE
Chapter 4 Parts PUSHBUTTON ASSEMBLY
5647-12133-00
Part No. Description Qty 20-10209-1 | pushbutton long shaft, red 20-10209-3 | pushbutton long shaft, blue 20-10209-4 | pushbutton long shaft, green BLA, ALA
20-10209-5 | pushbutton long shaft, yellow
VIDEO ASSEMBLY (A-22923)
8675-15355-00
03-9764
When ordering video components, identify monitor and CRT manufacturers. Manufacturer is marked on the neck or main board assemblies. CRT brand is typically marked on the tube near the deflection yoke.
CRT, frame, deflection yoke, and remote adjustment board assembly are unavailable separately. These components are specific to monitors and cannot be interchanged. Monitors use CRTs with slightly different shapes. Each bezel fits only one shape correctly. Each monitor board set consists of a neck board assembly and a main board assembly as a matched set. CRTs use different glorification yokes. Each board set matches only one CRT and yoke correctly.
Each video assembly consists of a complete monitor and matched bezel. Complete video assemblies are electrically and mechanically interchangeable in a cabinet.
Chapter 4 Parts
ELECTRONICS ASSEMBLY (A-23601)
04-12393 COVER
RM-37-11 FLEXIBLE GROMMET
4408-01128-00 20-10493 | NUT #8-32 KEPS SHIELDED VIDEO CABLE \ | \ a 00012-00 5795-15344-07 \ HARD DISK DRIVE CABLE 7”
H-23127 —~ HARD DRIVE R AND FAN HAR
HARD DRIVE
4308-01 123-20 BOLT 8-32xi-1/
4006-01209-04 /4 P-PH— OFF, HEX NYLON
20-10601 RD ASSEMBLY PRIN:
4008-01005-16 8-32x1 P—PH
A-23620 SOUND 1/0 MBLY
4700-00011-00 FLATWASHER .172x.437x.059 —“ 5556-13956-00 FERRITE BEAD 1-1/4—/
Chapter 4 Parts
ELECTRONICS SECURITY
PANEL
Chapter 4 Parts
FLUORESCENT LAMP ASSEMBLY (A-22365) 20-10443 eet ASScELy ; LAMP HOLDER W/STARTER oN ; 20-10480 STARTER
: >a 4408-01128-00 os ~— NUT 8-32 KEPS
20-10444 LAMP HOLDER
24-8809 OR 24-8874 FLUORESCENT BULB 18” 15W 20-8749-8 BALLAST 120V 60HZ
FLUORESCENT LAMP ASSEMBLY (A-22506)
20-10444 aa LAMP HOLDER 4002-01105-04 a SCREW #2-56 P-PH ¥
ss 20-10481.2 >Z—~_ ELECTRONIC BALLAST 04-11241.1 FLUORESCENT HOUSING ~~~
Lo 0444 LAMP HOLDER
ne 24-8809 OR 24-8874
FLUORESCENT BULB 18” 15W
SPEAKER PANEL ASSEMBLY (A-22524) 4408-01128-00 e NUT 8-32 KEPS ~ 4700-00009-00 FLATWASHER .172 X .487 X .032 mN
5555-15098-00 f SPEAKER 8 OHM _ ; 5-1/2 FULL SHIELDED RM-22-37 FOAM TAPE 24”
H-22499 GROUND WIRE 04-01128-00 SPEAKER PANEL
Chapter 4 Parts COIN DOOR ASSEMBLY
27-3729
27-3730 or 27-3733
- 27-3731
03-8863
5580-13476-00
COIN DOOR AND LINE CORD CHART
Country Coin Door Line Cord
| US | 09-72000-1 | 5850-15521-01 |
| Germany | 09-96010.1 | 5850-15521-02 |
| France | 09-96010.1 | 5850-15521-02 |
| UK | 09-96010.1 | 5850-15521-03 |
| Italy | 09-96010.1 | 5850-15521-00 |
| Japan | 09-72000-15 | 5850-15521-06 |
| Spain | 09-96010.1 | 5850-15521-02 |
Chapter 4 Parts
POWER SUPPLY ASSEMBLY (20-10400.1)
LINE VOLTAGE ———, SWITCH
POWER SWITCH
UNE FUSE
LINE CONNE!
\— INTERNAL. 12vDC_FAN
| A.C. AUXILIARY POWER | D.C. MAIN POWER | HARD DISK DRIVE POWER | |||||
| CONNECTOR | CONNECTOR | CONNECTOR | |||||
| PINS | FUNCTION | PINS | FUNCTION | COLOR | PINS | FUNCTION | COLOR |
| 1 | LINE | 1,2,3 | +5 VDC | 1 | +5 | VDC | RED |
| 2 | GROUND | 45,6 | RETUR | 2.3. | RETURN | BLAC | |
| 3 | NEUTRA | 7 | 4 | 12 VDC YELLOW |
4408-01128-00 NUT 8-32 KEPS
4406-01128-00 —— NUT 6-32. KE!
4700-00008-00 FLAT W 156x.625x 20-10400.1 _/ POWER SUPPLY ASSEMBLY / jatBER GAP &5731-14529-00 FUSE 6.34 250¥
Chapter 4 Parts CPU BOARD ASSEMBLY (A-23619)
FIELD REPLACABLE PARTS
| Designation | Part No. | Function | Description |
| U8A | 5460-15671-00 | +3V Regulator | Voltage Regulator 3.3BT |
| Ull | A-22545 | Game Setup Memory | EPROM 93C46 | |
| U13 | A-22560 | Game Logic Circuit | | PAL Assembly |
| U18 | A-5343-30046-1 | | CPU Boot ROM | EPROM Assembly |
Chapter 4 Parts SOUND I/O BOARD ASSEMBLY (A-23620)
a FE
“Vagos ie Gs eee \
. y2 4 of ‘a t
q U2
FIELD REPLACABLE PARTS
| Designation | Part No. | Function | Description |
| U1, U2 | 5344-15764-00 | FIFO Memory Circuit | | AM 7201-35JC |
| U19, U20 | 5370-14146-00 | Audio Amplifier | TDA 72044 |
| U28 | 5880-15774-00 | Memory Backup | Lithium Battery |
U37 A-23622 Security PIC Assembly
| U44 | A-5343-30022-3 | Audio Instructions | EPROM Assembly |
Chapter 4 Parts VIDEO CARD ASSEMBLY (20-10601)
Chapter 4 Parts Other Parts Necessary
Protection
Fuse, 1A, 250V, Fast Blow5730-15278-00
Cables
Control Module Harness Cable H-22498
Main Harness (JAMMA) Cable H-22495
AC Harness Cable H-23609
AC Line Harness H-22399
RFI Jumper H-22393
DBV Harness H-23610
Light and Speaker Harness Cable H-22497
Fluorescent Light Cable H-21492
Hard Disk Drive Ribbon Cable 5795-15344-07
Hard Drive Power and Fan Harness H-23127
Ground Wire H-22499
Ground Wire - Braided H-21672
Fluorescent Lamp Cable H-22384
Fluorescent Light Adapter H-23624
Documents
Game Manual 16-30046-101
Product Safety Manual 16-10341
Game Registration Card 16-10650
Other Items:
T-27 Long Arm Wrench 20-10140
T-20 Long Arm Wrench 20-9620
Epilepsy Label 16-9922.1
Light Bulb #555 24-8768
Wiring
ce NOTICE: Information in this manual may change without notice. Midway Games West Inc. reserves the right to make improvements in equipment function, design, or components as progress in engineering or manufacturing methods may warrant.
Chapter 5 Wiring EDGE CONNECTOR CHART
| FUNCTION | WIRE COLOR | PIN | PIN | WIRE COLOR | FUNCTION |
| Ground | Black | A | d | Black | Ground |
| Ground | Black | B | 2 | Black | Ground |
| +5VDC | Red | Cc | 3 | Red | +5VDC |
| +5VDC | Red | D | 4 | Red | +5VDC |
| -5VDC | Yellow | E | 5 | Yellow | -5VDC |
| +12VDC | Orange | F | 6 | Orange | +12VDC |
| Key | NIC | H | 7 | NIC | Key |
| Coin Counter 2 | Brown-Red | J | 8 | Brown | Coin Counter 1 |
| Not Used | NIC | K | 9 | NIC | Not Used |
| Speaker -, Left | Brown-Gray | L | 10 | Red-Gray | Speaker +, Left |
| Speaker +, Right | Brown-White | M | 11 | Red-White | Speaker-, Right |
| Video Green | Yellow-Green | N | 12 | Yellow-Red | Video Red |
| Video Sync | Yellow-White | P | 13 | Yellow-Blue | Video Blue |
| Service Credits | White-Gray | R | 14 | Yellow-Black | Video Ground |
| Slam Tilt | Black-Green | Ss | 15 | Black-Blue | Test |
| Coin 2 | Black-Red | T | 16 | Black-Brown | Coin | |
| Player 2 Start | Violet-White | U | 17 | White | Player | Start |
| Player 2 U/D Bit 0 | Violet-Black | Vv | 18 | White-Black | Player 1 U/D Bit 0 |
| Player 2 U/D Bit 1 | Violet-Brown | WwW | 19 | White-Brown | Player 1 U/D Bit 1 |
| Player 2 U/D Bit 2 | Violet-Red | x | 20 | White-Red | Player 1 U/D Bit 2 |
| Player 2 U/D Dir Bit | Violet-Orange | Y | 21 | White-Orange | Player 1 U/D Dir Bit |
| Player 2 L/R Bit 0 | Violet-Yellow | Z | 22 | White- Yellow | Player | L/R Bit 0 |
| Player 2 L/R Bit 1 | Violet-Green | a | 23 | White-Green | Player | L/R Bit 1 |
| Player 2 L/R Bit 2 | Violet-Blue | b | 24 | White-Blue | Player 1 L/R Bit 2 |
| Player 2 L/R Dir Bit | Violet | c | 25 | White-Violet | Player 1 L/R Dir Bit |
| Not Used | NIC | d | 26 | NIC | Not Used |
| Ground | Black | e | 27 | Black | Ground |
| Ground | Black | f | 28 | Black | Ground |
SOLDER SIDE COMPONENT SIDE Joystick control wires that are not part of the main JAMMA Harness
| Ground | Black | 1 | 1 | Black | Ground |
| +5V | Red | 2 | 2 | Red | +5V |
| Not Used | NIC | 3 | 3 | Not Used | NIC |
| Key | NIC | 4 | 4 | Key | NIC |
| Not Used | NIC | 5 | 5 | Not Used | NIC |
| Player 4 Start | Grey-White | 6 | 6 | Blue-White | Player 3 Start |
| Player 4 U/D Bit 0 | Grey-Black | 7 | 7 | Blue-Black | Player 3 U/D Bit 0 |
| Player 4 U/D Bit 1 | Grey-Brown | 8 | 8 | Blue-Brown | Player 3 U/D Bit 1 |
| Player 4 U/D Bit 2 | Grey-Red | 9 | 9 | Blue-Red | Player 3 U/D Bit 2 |
| Player 4 U/D Dir Bit | Grey-Orange | 10 | 10 | Blue-Orange | Player 3 U/D Dir Bit |
| Player 4 L/R Bit 0 | Grey-Yellow | 11 | ll | Blue-Yellow | Player 3 L/R Bit 0 |
| Player 4 L/R Bit 1 | Grey-Green | 12 | 12 | Blue-Green | Player 3 L/R Bit | |
| Player 4 L/R Bit 2 | Grey-Blue | 13 | 13 | Blue | Player 3 L/R Bit 2 |
| Player 4 L/R Dir Bit | Grey-Violet | 14 | 14 | Blue-Violet | Player 3 L/R Dir Bit |
Chapter 5 Wiring MAIN CABINET WIRING DIAGRAM
DUAL TMU CARD
VEGAS CPU BOARD ASSEMBLY
[O “igctaonics assewsty |
POWER coRD
Chapter 5 Wiring VEGAS CPU BOARD ASSEMBLY
VEGAS CPU ASSEMBLY SWITCH
| Designation | Location | Function | Positions | State | Meaning |
| SI | Edge near U4 | Resets and | 2 | Off | Normal |
and US Restarts Operation Game
| Sl | Edge near U4 | Resets and | 2 | On | Forced Reset |
and US Restarts Game
Chapter 5 Wiring VEGAS CPU BOARD ASSEMBLY JUMPER POSITION CHART
| Designation _| Location | Function | Meaning | Position | Default | ||
| J1 (Note 1) | Near U19 & | CPU Boot ROM | |EPROM | Pins | 1&2 | x |
| Connector P4 | Type (U18) | Flash ROM | Pins 2 & 3 | |||
| J2 (Note 2) | Near U19 & | CPU Boot ROM | 1,2, | or 4Mbit flash ROM | Pins | & 2 | x | |
| Connector P4 | Size (U18) | 8 Mbit flash ROM | Pins 2&3 | |||
| J3 (Note 1) | Near U19 & | CPU Boot ROM | |EPROM | Pins 1 &2 | x | |
| Connector P4 | Type | Flash ROM | Pins 2&3 | |||
| J4 (Note 2) | Near U19 & | CPU Boot ROM | 2Mbit ROM | Pins 1 & 2 | x | ||
| Connector P4 | Size (U18) | 1Mbit ROM | Pins 2 & 3 | |||
| J5 (Note 3) | Near U19 & | Expansion Boot | 4Mbit ROM | Pins 1 &2 | x | ||
| Connector P4 | ROM Size (U19) | 8Mbit ROM | Pins 2 & 3 | ||||
| 16 | Between U13 | Boot Program | Boot from CPUROM | Pins 1 & 2 | XxX | ||
| & U8 | Location | Boot from SIO ROM | Pins 2 & 3 |
VEGAS CPU BOARD ASSY LED INDICATOR STATUS CHART
Designation Location Function Color State Meaning
| LED1 (Note 1) | Near U3 & U10 | |3.3V CPU Power | Red | Off | Insufficient Power |
Indicator On Power OK
Blinking Power Fault
| LED2 (Note 2) | Near U19 & | Hard Disk | Green | Off | Not in use |
| Connector P4 | Drive Activity | On | Locked Up |
Blinking Normal disk activity
| LED3 (Note 3) | Near U13 & UI7 | Indicator | Red | Off* | *See Note Below |
On*
Blinking* Sequentially
Chapter 5 Wiring VEGAS SOUND I/O ASSEMBLY
VEGAS SOUND I/O BOARD ASSY JUMPER POSITION CHART
Designation Location Function Meaning Position State
| J1 (Note 1) | Near U9 & | Gun 1 1/0 | Input Mode | Pins 1 & 2 | xX |
| Crystal Y3 | Connector P2 | Output Mode | Pins 2 & 3 | |||
| J2 | Between U35 and U10 | Video Sync | Positive Syne | Jumper Not Installed | |X |
Negative Sync | Pins 1 & 2
| J3 (Note 2) | Near UI5 | Gun 2 I/O Connector P4 | Input Mode | Pins 1 & 2 | xX |
Output Mode | Pins 2 & 3
| J4 | None | None | Not Used | None | a |
| J5 (Note 2) | Between U15 & | Gun 2 I/O | Input Mode | Pins 1 &2 | xX |
| Connector P2 | Connector P4 | Output Mode | Pins 2 & 3 | |||
| J6 | None | None | Not used | None | a |
| 7 | None | None | Not Used | None | oa |
| J8 (Note 1) | Between U9 & | Gun | I/O | Input Mode | Pins 1 & 2 | x |
| Connector P4 | Connector P2 | Output Mode | Pins 2 & 3 |
Chapter 5 Wiring VEGAS SOUND I/O BOARD ASSEMBLY LED INDICATOR STATUS CHART
Designation Location Function Color State Meaning
| LED1 | Near U11 | SIO Board | Green | Off | No boot ROM |
| Activity | On | SIO Board locked up |
Blinking | Power Fault
| LED2 | Near U34 | Linking | Green | Off | Not in use (no game linking) |
| Crystal Y1 | Connector Status | On | Normal Linked Operation |
Blinking | Link Fault
| LED3 | Near the Jamma_ | |-5V Power | Red | Off | No power |
| Connector | indicator | On | Normal operation |
Blinking | Power fault
| LED4 | Near U35 & | +12V Power | Red | Off | No power |
| Connector P14 | indicator | On | Normal operation |
Blinking | Power fault
| LEDS | Near | +5V Power | Red | Off | No power |
| Connector P23 | indicator | On | Normal operation |
Blinking | Power fault
| LED6 | Near U34 & | CPU Linking | Red | Off | Not in use |
| Crystal Y1 | Activity | On | CPU linking in progress |
Blinking — | Normal operation
| LED7 | Near U34 & | Linking Data | Red | Off | Not in use (no game linking) |
| Crystal Y1 | On | Sending data |
Blinking — | Normal operation
| LED8& | Near U14 & | Audio Activity | Yellow | Off | No sound boot ROM |
| Crystal Y1 | On | Locked up |
Blinking — | Normal operation
| LED9 | Near U34 & | Linking | Yellow | Off | Not in use (no game linking) |
| Crystal Y1 | Receiving data | On | Receiving data |
Blinking — | Normal operation
| LED10 | Near U44 & | Audio activity | Green | Off | Not in use (no audio data) |
| Crystal Y2 | On | Receiving data |
Blinking — | Normal operation
| LED11 | Near U44 & | None | Red | Off | Not in use (normal) |
| Crystal Y2 | On | Circuit fault |
Blinking | Circuit fault
| LED12 | Near U44 & | Interrupt activity | Yellow | Off | Not in use (no interrupts) |
| Crystal Y2 | On | Receiving data |
Blinking — | Normal operation
| LED13 | Near U44 & | Disk Activity | Yellow | Off | Not in use |
| Crystal Y2 | On | Processing data |
Blinking — | Normal operation
Chapter 5 Wiring
VEGAS SOUND I/O ASSEMBLY DIP-SWITCH SETTINGS
Service technicians may change DIP-switches with AC power on. “*” indicates factory defaults.
DIP Switch U13 sw | Sw2 | Sw3 | sw4 | Sws | SWo | Sw7 | Sws
| Display Comments on | No | ofr |
| VT100 | Yes | On |
Diagnostic Code Source _| Hard Disk Drive EPROM Off* On
Not Used Ofr* On
Not Used ofr On
Not Used Off*
Not Used Ofr* On
Not Used ofr On
Not Used Off* On
DIP Switch U12 swi | sw2 | sw3 | sw4 | sws | swo | sw7 | sws
| Monitor resolution | Standard | Off |
Medium On*
Monitor Style Video Game Off* VGA On
Joystick Type 8-Way Off
49-Way On*
Switch Condition Normally Closed Off Normally Open On*
Vegas Sound I/O Revisions | to 5 Off* Board Version Revisions 6+
Not Used Off* On
Not Used Off* On
Not Used Ofr* On
DC POWER SOURCE VOLTAGE LIMITS
| Function | Range Limits | Color | Function | Range Limits | Color | |
| Digital Circuits | +4.90 to +5.10V | Red | Coin Lights | -4.75V to -5.25V | Yellow |
| Audio, Lights | +11.5V to +12.5V | Orange | Auxiliary Power | -1L.SV to -12.5V | Blue |
Troubleshooting
Chapter 6 Troubleshooting Game Does Not Start
Symptom Problem Suggested Solution
- Machine appears non- Lack of electricity 1. Check that Power Switch has been turned on functional 2. Verify that line cord is plugged fully into receptacle and
- No audio into power supply.
- No Illumination No video display w . Try another power outlet.
Wrong voltage . Ensure power supply line voltage switch matches local line voltage. Using voltage meter, correctly adjust +5V output on power supply using adjustment knob.
Faulty line cord . Test line cord, power plug, and IEC connector for breaks or damage. Replace if necessary. . Verify continuity of each wire in cord.
Poor connection . Ensure cabinet wiring harness connectors are fully seated in corresponding power supply and board connectors. . Inspect wiring for breaks or damage.
Machine appears nonfunctional.
- Currency acceptor price indicator is illuminated CPU Board Assembly not operational
bad . Inspect board assemblies under low light level conditions. A glow will be seen from the Light Emitting Diodes if there is voltage in the processor circuits. This does not mean that voltages or signals are as they should be, but it indicates that boards are receiving some DC power from power supply. The power supply fan should also be operating. Turn AC power off. Inspect board assemblies. Ensure JAMMA wire harness connector is attached and fully seated onto mating board connector. Check other wiring harness connectors in same way. Verify game switches and jumpers are set correctly. Refer to Board Configuration Chart for variables and default settings.
Power supply out of voltage tolerance. . Turn AC power on. Using 20V DC setting on digital voltmeter, measure voltages at power connector pins. Adjust +5V source if necessary. Refer to Cabinet Wiring Diagram for specific wiring information and voltage limits. . Using 2V AC setting on digital voltmeter, measure same DC voltages as above. A reading indicates that supply voltages are unstable and may contain ripple or noise.
Game cannot be played Chapter 6 Troubleshooting
Symptom Problem Suggested Solution
- Game does not accept currency or tokens.
- Game does not start. + Audio present
- Video present Blocked coin path.
- Unlock and open cash door. Empty cash box and inspect revenue for counterfeit currency.
- Remove items that block path from coin mechanism.
- Ensure proper mounting of each mechanism. Clear currency path. Reinstall and latch mechanism.
Poor leveling Verify mechanisms are level when doors are closed. Repair or replace bent or damaged coin door. Adjust cabinet leg levelers to keep mechanisms vertical.
Incorrect software setting . Enter Menu System by pressing TEST MODE switch. From SELF TEST menu, choose COIN OPTIONS. Confirm pricing and setup of each mechanism.
- Choose CONTROL TESTS to check operation of each coin or bill mechanism.
- Game accepts currency or tokens.
- Game does not start. + Audio present
- Video present. . Ensure proper mounting of each mechanism. Verify each release latch is closed and locked. Test acceptance and rejection functions with known good and bad coins.
- Ensure no loose parts or wires are caught in hinges, latches, or switch contacts.
- Inspect illumination of external coin door indicators (i.e., pricing, flashing arrows). Check wiring continuity of connectors and cables from CPU Board to coin mechs.
- Enter Menu System by pressing TEST MODE switch. From SELF TEST menu, choose COIN OPTIONS. Use tests to confirm pricing and setup of each mechanism. . Check for continuity in each suspect switch connection (Common to Normally Open or Common to Normally Closed) Replace faulty switches (bent levers, broken actuators, etc.)
- Place coin mechs in known good unit to verify operation. w
wn
- Bill validator fails after field installation.
- Coin mechanisms operate properly. . Enter Menu System by pressing TEST MODE switch. From SELF TEST menu, choose COIN OPTIONS. Confirm pricing and setup of each mechanism. Check validator switch settings against manufacturer’s instructions.
- Check illumination of external coin door indicators (i.e.. pricing, flashing arrows). Free parts or wires caught in hinges, latches, or switch contacts. Verify seating of harness connectors. Check validator cable continuity.
- Place bill validator in known good unit to verify operation. w
- Coin indicators do not light.
- Game operates normally. Bad fuse. Check coin light fuse and wiring harness. Replace bad fuse.
Chapter 6 Troubleshooting Audio Problems
Symptom Problem Suggested Solution
- Audio non-functional.
- Video present.
- Game operates normally. Volume set too low
- Press TEST MODE switch to enter Menu System. From SELECT TEST menu, choose ADJUST VOLUME. Verify that attract and game volume levels are not set to zero. Change to appropriate levels.
- Return to previous menu and choose SOUND TESTS. Verify operation of each speaker.
Faulty hardware Turn off AC power. Remove grills and inspect speakers. Ensure no loose parts or wires are caught in speaker cones, terminals, mounting screws, or stuck to magnets.
Poor voltage
- Turn AC power on. Using 20 V DC setting on digital voltmeter, measure voltages at power connector pins. Verify +5V, -5V, and +12V sources. Refer to Cabinet Wiring Diagram for specific wiring information and voltage limits.
- Using 2 volt AC setting on digital voltmeter, measure voltages at speaker terminals. Any reading here indicates supply voltages are unstable and may contain ripple or noise. Place speaker in good machine to verify operation. bd
Audio muffled, distorted, or missing frequencies. Constant, low hum. Faulty speaker . Press TEST MODE switch to enter Menu System. From SELECT TEST menu, choose SOUND TESTS. These verify some audio functions.
- Using 2 volt AC setting on digital voltmeter, measure voltages at speaker terminals. Any reading here indicates supply voltages are unstable and may contain ripple or noise.
- Place speaker in good machine to verify operation.
Wrong speaker Turn AC power off. Remove grills and inspect speakers. Ensure each coaxial speaker is full range (100 to 10,000 Hz response) and rated for at least 10 watts.
Faulty wiring
- Check cabinet wiring is correct for game.
- Verify all cabinet wiring provides separate wires (not a common return) for each speaker.
- Ensure all ground wires are connected. Refer to Cabinet Wiring Diagram for specific wiring information.
- Weak, low frequencies. Thin or hollow sound quality Incorrectly phased speakers Inspect speaker wiring and reverse back to correct position. See Cabinet Wiring Diagram.
- Monaural audio Faulty wiring Verify cabinet wiring is correct. Check for shorted wires. Refer to Cabinet Wiring Diagram.
Chapter 6 Troubleshooting Video Problems
Symptom Problem Suggested Solution
Monitor appears nonfunctional. + Audio present Controls operate normally. Poor signal . Verify AC power is connected to video monitor. . Inspect neck of CRT under low light level conditions. If there is voltage in filament circuits, you will see a glow near the CRT base. This indicates monitor circuits are receiving power, not that voltages or signals are proper. . Turn AC power off. Verify video signal and remote adjustment board connectors are fully seated on video monitor board assembly. Check other monitor connections in the same way.
- Examine AC line fuse on video monitor. If faulty, replace with fuse of proper voltage and current rating. . Ensure no loose parts or wires are caught on chassis or mounting brackets. N
w
wa
Bad settings Ensure brightness and contrast are not at minimum levels.
+ Power-up self test runs.
- Game does not appear.
- No audio. Error message Record error messages. Press TEST switch to enter menu system. From SELECT TESTS menu, choose DISK TESTS. These tests verify hard disk drive functions.
Faulty hard disk drive . Turn off AC power. Unlock and open front door. Ensure hard disk cable connector is fully seated on CPU Board. Ensure all hard drive mounting screws are installed.
- Ensure hard disk, ROM set and CPU Board Assembly are correct part for game. Each component is labeled with the assembly number and software or hardware version.
Poor voltage . Turn AC power on. Use 20V DC setting on digital voltmeter to measure voltages at power connector pins. Verify +5V source.
- Using 2V AC setting on digital voltmeter, measure same DC voltages as above. A reading indicates that supply voltages are unstable and may contain ripple or noise. . Compare LED states with indicator charts. w
Monitor fails to lock onto signal and provide stable picture.
- Colors missing, etc. Poor syne . Check connectors and cables for wiring continuity from CPU Board Assembly to monitor. Verify jumpers are set correctly for monitor. . Ensure monitor is correct for game. Incorrect resolution results in horizontal tearing or complete loss of sync.
- Place monitor in working machine to verify operation. we
- Picture wavers or rolls, has dark bars, uneven colors, etc.
- Game operates normally. Faulty wiring . Check connectors and cables for wiring continuity from CPU Board Assembly to monitor.
- Ensure all cabinet ground wires are connected, especially at monitor chassis.
- Place monitor in good machine to verify operation.
Interference from other equipment Move cabinet away from machines, appliances, other games, etc. Very strong electrical or magnetic fields are emitted from some equipment when operating normally.
Chapter 6 Troubleshooting Miscellaneous
Symptom Problem Suggested Solution
- Indicator lamps intermittent or non-functional.
- Game starts and plays normally.
w
wn . Open marquee. Remove fluorescent tube from holders. Install new lamp if cracks or darkened ends are found. Clean tube. . Verify that lamp and starter pins make good connection with socket contacts.
- Measure Fluorescent Lamp Assembly AC voltages. Check wiring and connector continuity from Power Supply connector to lamp assembly. Ensure Fluorescent Lamp Ballast is rated for local AC line voltage and frequency. . Check for continuity of both fluorescent lamp filaments, starter, and ballast. One at a time, verify that lamp, starter, and ballast operate by placing each in a known good unit. . Examine DC fuse on Electronics Assembly shelf. If any fuse is faulty, replace with identical fuse from spare parts bag. Replace spare fuse when repairs are complete.
- Game operates normally.
- Fan noisy. wNne= . Check bottom and rear of cabinet for blocked air flow. Move game away from heat sources. . Turn AC power off. Remove dust from vent holes with high power vacuum cleaner. . Unlock and remove rear door. Ensure fan is connected to wiring harness.
- Game resets randomly.
w . Check fan assemblies on CPU Board Assembly. Ensure fans are connected to power sources. . Check cabinet and Electronics Assembly ventilation holes for obstructions.
- Clear obstructions and allow ventilation holes access to fresh air.
« Error messages appear. . Check any assembly identified in error message.
- Game does not start. 2. Call your authorized distributor for help with unresolved
- No audio. screen messages.