Baseball Season 2
Baseball: The Season II (Cinematronics, 1987) · Manual · 41 pages · 16 sections · original scan
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
BASEBALL, THE SEASON II
INSTALLATION AND MAINTENANCE MANUAL
THE LELAND CORPORATATION
CINEMAT SYSTEM
1841 Friendship Drive
El Cajon, CA 92020-9981
Telex: CINTRON 4974293
FAX: 619-562-9468
FCC WARNING
This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual, may cause interference to radio communications.
It has been tested and found to comply with the limits for class A computing devices pursuant to subpart J of part 15 of FCC Rules, which are designed to provide reasonable protection against such interference when operated ina commercial environment.
Operation of this equipment in a residential area is likely to cause interference in which case the user at his own expense will be required to take whatever measures may be required to correct the interference.
POWER REQUIREMENT WARNING !
A power supply capable of supplying the following current (or greater) must be used for game conversion:
7 amps @ + 5.0 VDC 1 amp @ - 5.0 VDC 1 amp @ + 12.0 VDC
RECORD OF SERIAL NUMBERS
Record the game serial numbers and date purchased for future reference and/or game service.
Date purchased:
Main Circuit Board S/N:____
Input/Output and Memory Expansion circuit board S/N: __
Program part number (on EPROMS) 300
Software serial number (on “attract mode" screen):
TABLE OF CONTENTS
SECTION PAGE
A. WARRANTY 6
‘B. HINTS FOR SUCCESSFUL GAME INSTALLATION 7
Le. Inspect Your Kit 8
- The Old Case of the Bent IC Pin 8
- Attach the Ground 8
4, Which Pole is Which (Observing Polarity) ? 8
- Marquee Blues (Marquee Installation) 10
- Run Diagnostics (or Game Installaion 11 Success or Failure)
- Monitor Outputs 11
- How Do I Turn Up the Sound ? 11
C. GAME MODULE INSTALLATION 12
vb. UNIVERSAL GAME CONVERSION 19
C. BOOKKEEPING/DIAGNOSTIC FUNCTIONS 22
- Invoking Diagnostics 23
Zw Selecting The Desired Function 23
- Bookkeeping 24
a. Period and Dollar Counters 24
b. Setting Coins/Tokens per Dollar 24
Cc. Example of Setting Tokens 25 per Dollar
- Diagnostics 26
a. Buttons And Controls Test 26
b. Processor Memory Test 27
Cw Video Alignment Display 28
TABLE OF CONTENTS, cont'd
SECTION
d. Video Memory Test
e. Viewing Background Screens and Background Test
- Game Set Up
a. Coins per Credit / Credits per Coin
be Extra Play
c. Attract Mode Sound
- Game Play Statistics
- Inning Duration Graphs
- Erase All Player Statistics
SYSTEM TROUBLESHOOTING GUIDE
- Input/Output Functions
- Electronics
- General Knowledge
4, Coin Counter Surge Protection Circuit
CONNECTOR PINOUT CHART
TABLE OF CONTENTS, cont'd
LIST OF ILLUSTRATIONS
FIGURE DESCRIPTION PAGE
1 AC/DC Power Connection 9
2 Marquee Installation 10
3 Main Circuit Board Assembly 15
4 Input/Output and Memory Expansion 16 Circuit Board Assembly
5 Control Panel Bolt and Ground Braid 17
6 Piggy-back Circuit Board Mating 18
7 Control Panel Mounting and Cable Routing 21
8 Coin Counter Surge Protection Circuit 36
A. WARRANTY
Seller warrants that its printed circuit boards, monitor and power supply, when furnished with the product and parts thereof are free from defects in material and workmanship under normal use and service for a period of ninety (90) days from date of shipment. Seller's warranty of above parts is subject to the normal use and service of its product. None of the seller's other products or parts thereof are warranted,
If the products described in this manual fail to conform to this warranty, seller's sole liability shall be, as mutually agreed, to replace or repair such products which are returned to seller during said warranty period provided.
CONDITIONS:
a. Seller must be promptly notified in writing upon discovery by buyer that said products are defective. b. Products must be returned prepaid to seller plant. ron Seller's examination of said products discloses to seller's satisfaction that such alleged defects existed and were not caused by accident, misuse, neglect, alteration, improper repair, installation or improper testing.
Seller is not responsible for bent pins on ICs not installed by seller's employees. In no event shall seller be liable for loss of profits, loss of use, incidental or consequential damages.
Except for this express warranty, seller disclaims all other warranties, expressed or implied, including the implied warranties of merchantability and fitness for a particular purpose, and all other obligations or liabilities on seller's behalf, and it neither assumes nor authorizes any other person to assume for seller any other liabilities in connection with the sale of products manufactured by seller.
NOTICE REGARDING THE USE OF NON-SELLER REPLACEMENT PARTS:
Seller recommends the use of only seller's parts when replacing any malfunctioning component or assembly in the seller's system. For safety and reliability, seller does not recommend or authorize any substitute parts or modifications of seller's equipment. Such alterations may adversely affect game play, cause serious injury, and void your warranty. Unauthorized parts, modifications and non-seller's game conversion kits may also void FCC compliance.
To obtain repair, contact seller at 619-562-7000 between 8 AM and 5 PM Pacific Standard Time to obtain an RMA return authorization number. Affix this number to the outside of the shipping container when returning goods. Return to the above address.
B. HINTS FOR SUCCESSFUL GAME INSTALLATION
B. HINTS FOR SUCCESSFUL GAME INSTALLATION
Take some advice from the game masters. Successful game installation can be simple if you take a minute and read the following hints. It is worth it's weight in aspirin!
- INSPECT YOUR KIT
Inspect all received parts for shipping damage and to familiarize yourself with the parts. Inspect all integrated circuits (hereafter called "IC" for bent pins (being careful not to bend the pins).
- THE OLD CASE OF THE BENT IC PIN
The #1 killer of a successful game installation, or for that matter, any other electronic device's proper operation, is bent pins. Avoid this plague and take the time (and patience) to make sure that all pins are in each hole and not bent.
Also, installing ICs with bent pins runs the risk of bending the pins even further and eventually breaking them,
If pins are bent, first, grip the group of pins lengthwise with long needle-nose pliers. This gripping action will straighten them in this direction. Next, if any pins are bent in the other direction, straighten each one individually with needle nose pliers being careful not to over-compensate. This overcompensation may break the pin,
- ATTACH THE GROUND
Make sure to attach the ground braid to the control panel. Players risk an electric shock if the control panel is not properly grounded.
Refer to figure 5 for ground braid connection.
- WHICH POLE IS WHICH (OBSERVING POLARITY)?
Electronic circuits are quite sensitive to polarity and can easily lose their sense of humor when the polarity is reversed. A fuse may not be all they blow! Experienced electronic engineers check the polarity two times before applying power! You should probably check it three times.
Refer to figure 1 on the next page for proper 115 VAC and DC power connections.
FIG. AC/DC POWER CONNECTION
GROUND BRAID
POWER CORD
° a
° a a
]
115 vac
E.M.I. FILTER
INTERLOCK
SWITCH
- CONTROL PANEL BROWN
| rT FLUORESCENT Aorounstnrna aormrontrna DAonrnonwtnrana
a
-5V N HOT AC GND AC
FUSE A.POWER SUPPLY +5V @ 7A -5V @ 1A +12V @ 1A COIN DOOR LIGHTS B.I/O MEMORY EXPANSION BOARD C.MAIN LOGIC BOARD
ISOLATION TRANSFORMER D.cIRCUIT PANEL PLATE
SEC PRI
MONITOR PIN 10 PIN 1 OUR PIN-OUT IS OPPOSITE OF THE PIN-OUT PRINTED ON THE CONNECTOR GROUND BRAID I.E. PIN 1 IS PIN 10 FOR A 10 PIN CONNECTOR
- MARQUEE BLUES (MARQUEE INSTALLATION)
Your game is a money making investment! Why compromise by installing a crooked marquee? Avoid this and follow these instructions for installing:
First, place the plexiglass on a table. Next, center the decal on the plexiglass, getting an idea of the general location (before peeling off the back). Now, carefully peel off the back and place the far edge (lengthwise) on the plexiglass first, centering the remaining un-stuck (important) decal. Finally, "roll" down the rest of the decal, slowly, squeezing the air bubbles out with your hand.
Pictured is the marquee on a Cinemat System Cabinet.
MARQUEE INSTALLATION
FIG. 2
BASEBALL, THE SEASON II - INSTALLATION & MAINTENANCE MANUAL
RUN DIAGNOSTICS (OR GAME INSTALLATION SUCCESS OR FAILURE)
Five minutes of diagnostics may save an hour of frustration wondering why a feature does not work. Our software department is the best in the business. They labored long and hard to write diagnostics to thoroughly check out your game. Take the time to follow the diagnostics section and prove to yourself that the entire game is working properly.
Next, play the game a couple of times to verify that all is well.
MONITOR OUTPUTS
The outputs from our system to the monitor are red, green and blue with negative horizontal and negative vertical sync.
HOW DO I TURN UP THE SOUND ?
Volume adjustment is easy. Refer to figure xx and locate VR1 (on main circuit board). Now look at the main board (largest board). Clockwise rotation increases the volume.
C. GAME MODULE INSTALLATION
c. GAME MODULE INSTALLATION
1. Parts for the BASEBALL, THE SEASON II game module are as follows. Please inspect and check off:
lO a eK DESCRIPTION
Manual, BASEBALL the SEASON II BASEBALL Marquee Lexan Decal Plexiglass Marquee Cinemat I/O Expansion Board 2 EPROMs (Game Software) Custom Chip (U120) 02-12 Custom Chip Control Panel Assembly 1 1/2" Carriage Bolts #10 Flat Washers #10-24 Hex Nuts #10-24 Wingnuts 5/16"x 1" Spacers 6/32"x 1-1/2" Bolts 40 Pin Ribbon Interconnect Harness 10 Pin Power Interconnect Harness PRPUUNNEEAREPPNBERPE
Install the 22 BASEBALL EPROMS in the main board noting the chip location ("U" number) printed on each chip and referring to Figure 3. Match the location of pin 1 of both the EPROM and socket, plug each EPROM into the socket indicated. Be sure all EPROMs' pins are aligned and the EPROMs are pressed firmly in place.
Install the custom chip U120 in the main logic board at location U120 and the 02-12 custom chip at U85 making sure Pin 1 of the chip and Pin 1 of the socket are aligned.
Recheck steps 2 and 3 for proper parts placement and orientation.
Remove the Z-80B microprocessor from location U99 of the main logic board and reinstall it at location U13 of the I/O and Memory Expansion board. Install the I/O and Memory Expansion board ribbon cables as shown in figure 6.
Position the BASEBALL control panel assembly on the cabinet and attach using the 1 1/2" carriage bolts, washers and 10-24 hex nuts provided. Install only the front-most bolt, washer, and nut on each side at this time. See figure 5.
7.
10. Route the control panel wiring harness. Locate the three connectors labeled P5, J4 and J5 at the end of the control panel harness. Plug connectors P5 into connector P5 located along the top edge of the main logic board. Similarly, plug J4 into J4 and JS into J5 of the I/O and Memory Expansion board. Plug the remaining two wires (white and violet) of the control panel harness into connector P4 of the main board. Refer to Connector Pinout Chart in back of manual.
Attach the marquee to the plexiglass using the procedure in section B above.
Installation of the game module is now complete. We suggest you now use the system's "on board” diagnostics to inspect the game. See the diagnostics section of this manual.
After testing the control panel, use the remaining two carriage bolts, washers and wing nuts to secure the control panel.
FIG. MAIN CIRCIUT BOARD ASSEMBLY TO MONITOR o TYPICAL PIN 1 LOCATION TO SPEAKER i P2 VOLU ME VREO CantRoL BALL II 03-+14119-90 SEBALL II 03-14118-00
USED U90 BASEBALL II 03-14110-00 BASEBALL II 03-14108-00 U6T BASEBALL I 03-14107-00 Pa Ty) POWER IN RESET Swi E: Pay WIi2ZoO Ly es]! TO CONTROL PANEL LU P6TT NOT USED P4:COIN SW SERV SW 1 AND 2 PLAYER START
BASEBALL THE SEASON IT MEMORY AND I/O EXPANSION PRINTED CIRCUIT ASSEMBLY COMPONENT SIDE — T AIddaAS UaMod
= ©909000 Cc, ce) j Ww NOT USED nN e000000 o ¢loo000000 — :
| =—[00000000 | “ | z | |
| i | on | atl | |
| E | 17-91 | N 5 Nor useD | | Ss W |
oO | ” 8
g
c Ct x ooh ce Bas SD ex x8 a3 ial Cc i o~ = NOT USED ni 15-01 1 90 & 2 wo c , 4 a p $ wo w co} Lo] < g
- a ws Of ree ae 7 o [ p-- = — == si] Ugg U Ba = INPUT/OUTPUT AND
ein ° He” MEMORY EXPANSION
LOCATION Q CIRCUIT BOARD ASSEMBLY
5 FIG. 4
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
yer
Qe»
Ouray
Qe»
PIGGYBACK CIRCUIT BOARD MATING
FIG. 6
D. UNIVERSAL GAME CONVERSION
D. UNIVERSAL GAME CONVERSION
- Parts for the BASEBALL, THE SEASON II conversion kit are as follows. Please inspect and check off:
QTY DESCRIPTION
Plexi, Marquee Decal, Marquee 0 Ty-Wrap w/eyelet Control Panel Assembly,BASEBALL the SEASON Il Circuit Board Assembly,BASEBALL the SEASON II Manual, BASEBALL the SEASON II Harness, Video Harness, Coin Service Harness, Speaker Decals, Cinemat DC Power Harness PNPRPRPRPRPRPBRPER
- Remove existing game control panel, and all buttons or joystick controls associated with it. Position the universal control panel above the control panel intended for conversion, Feed the harness through a convenient hole large enough for the harness connectors. Refer to Figure 7. ass,
- Securely mount the universal control panel with a bolt or screw not easily removed from the exterior of the cabinet. Avoid pinching the wires. Secure using the ty-wraps included with your kit.
- When routing the harness, leave enough slack so that servicing of the control panel and circuit board assembly can be accomplished with relative ease. Place a wire ty-wrap as close to the circuit board connectors as possible to relieve strain on the connector pins.
- Mount the circuit board in an area of the cabinet that receives ample ventilation. Make sure the circuit board can be removed easily for service.
- Refer to the D.C. power wiring diagram, making all the power connections as shown. Be sure to hook up the ground braid. Also, observe proper polarity. Careful with this one!
- The last order of business is the Marquee and Plexiglass. See section B above for this procedure.
de The conversion process is now complete. It is recommended at this point, to go into diagnostics _ to test the performance of the new kit. °
S a mQ
wu()
CONTROL PANEL MOUNTING AND CABLE ROUTING
FIG. 7
BASEBALL, THE SEASON II - INSTALLATION & MAINTENANCE MANUAL
E. BOOKKEEPING / DIAGNOSTIC FUNCTIONS
S/N: BOOKKEEPING / DIAGNOSTIC FUNCTIONS
BASEBALL, THE SEASON II has extensive bookkeeping and diagnostic functions. These functions are explained in the following sections:
- INVOKING DIAGNOSTICS
With the game running in the attract mode follow these steps:
a. Press and hold the one-player start button while pressing and releasing the service button (found inside the coin door mounted to the top of the coin box). Concerning Kits, connect the appropriate pins to ground referring to the Connector Pinout Chart in the back of the manual.
b. Release the one-player start button.
Cc. The game screen should now appear as shown on the next page. Instructions for selecting and entering the listed functions are displayed at the top of the screen with the five selectable options below them. The game's software version number is shown in the lower left-hand corner of the screen.
- SELECTING THE DESIRED FUNCTION
The one-player start button selects the desired function. The function has been selected when the display color for that particular function changes. Pressing the two player start button enters the selected function. Selecting the RESTART THE GAME function returns the game to normal operation.
An example of the display is as follows:
MAIN MENU
SELECT FUNCTION WITH ONE PLAYER START BUTTON ENTER FUNCTION WITH TWO PLAYER START BUTTON
BOOKKEEPING DIAGNOSTICS GAME SET-UP GAME STATISTICS INNING DURATION GRAPHS ERASE ALL PLAYER STATISTICS
RESTART THE GAME
XKXXXXXX
BASEBALL, THE SEASON II - INSTALLATION & MAINTENANCE MANUAL
BOOKKEEPING
The bookkeeping screen is displayed when that option is selected and entered from the main menu. Five lifetime counters are shown. These counters are set to zero at the factory and are not resetable by the operator. These counters are:
COINS DROPPED MECH 1 - This counter shows the total number of coins that have dropped through the LEFT coin mech.
COINS DROPPED MECH 2 - This counter shows the total number of coins that have dropped through the RIGHT coin mech.
TOTAL COINS DROPPED - This is the total number of coins dropped through BOTH mechs.
SERVICE BUTTON PRESSED - The number of times that the service button has been pressed. Pressing the service button to enter the bookkeeping / diagnostic section does not affect this counter.
TOTAL CREDITS GIVEN ~- The total number of credits the game has given in it's lifetime is shown on this counter. (See the game setup section of this manual for information on setting the number of coins per credit).
a. PERIOD AND DOLLAR COUNTERS
Three resetable counters, located to the right of the lifetime counters are provided to aid the operator in tracking the games’ cash intake over a period of time. These counters are:
- coins dropped
- dollars collected
As in the main menu, these options are selected by pressing the one-player start button and entered by pressing the player two start button. To reset the period and dollar counters for either coin mech, press the one-player start button until the message "RESET COIN MECH 1 (or 2) DOLLARS COLLECTED" changes color. Then press the two-player start button.
b. SETTING COINS/TOKENS PER DOLLAR
To calculate dollars collected, the bookkeeping system needs to know how many coins/tokens are required to make a dollar. Normally, this number
BASEBALL, THE SEASON II - INSTALLATION & MAINTENANCE MANUAL
would be 4 for quarter operation. If you operate a location where, for example, 6 tokens equal one dollar, then the dollar multiplier should be changed to 6 so that the dollars collected counters will reflect accurately what the game has earned.
To change the coin "multiplier," use the one-player start button to highlight the COINS PER DOLLAR message for the desired coin mech then use the two-player start button to change the multiplier.
EXAMPLE OF SETTING TOKENS PER DOLLAR
An arcade giving 10 tokens per dollar should have the coins/tokens per dollar multipliers set as shown.
An example of the display is as follows:
10 COINS PER DOLLAR COIN MECH 1 10 COINS PER DOLLAR COIN MECH 2
BOOKKEEPING
SELECT FUNCTION WITH ONE PLAYER START BUTTON ENTER FUNCTION WITH TWO PLAYER START BUTTON
LIFETIME PERIOD COINS COINS DOLLARS
COINS DROPPED - MECH 1 0 0 $0.00 MECH 2 0 0 $0.00 TOTAL COINS DROPPED 0 0 $0.00 SERVICE BUTTON PRESSED 0 TOTAL CREDITS GIVEN 0
RESET COIN MECH 1 DOLLARS COLLECTED RESET COIN MECH 2 DOLLARS COLLECTED
SET COINS/TOKENS PER DOLLAR: 4 COINS PER DOLLAR COIN MECH 1 4 COINS PER DOLLAR COIN MECH 2
RETURN TO MAIN MENU
- DIAGNOSTICS
The diagnostic menu is displayed upon entering diagnostics from the main menu. The player can then select the desired function.
An example of the display is as follows:
DIAGNOSTICS
SELECT FUNCTION WITH ONE PLAYER START BUTTON ENTER FUNCTION WITH TWO PLAYER START BUTTON
BUTTONS AND CONTROLS TEST PROCESSOR MEMORY TEST VIDEO ALIGNMENT SCREENS VIDEO MEMORY TEST VIEW BACKGROUND SCREENS
RETURN TO MAIN MENU
a. BUTTONS AND CONTROLS TEST
This test allows the operator to check the game controls and switches. Pressing a button or activating a control causes the description of that button or control to change color on the video screen.
The word GOOD will appear to the right of the control's description when the switch contacts close and will remain on the screen until the button is released.
Pressing the two-player start or service buttons twice will end the test and return you to the diagnostic menu.
An example of the display is as follows:
PRESS THE FOLLOWING BUTTONS:
1 PLAYER START 2 PLAYER START MECH 1 COIN BUTTON MECH 2 COIN BUTTON SERVICE SWITCH
GO BACK BUTTON EXTRA BASE BUTTON — LEFT RUN/STEAL BUTTON RIGHT RUN/STEAL BUTTON RUN/CUTOFF BUTTON
RUN/AIM BUTTON
BATTERS JOYSTICK HORIZONTAL: xxH XXMXXXXX bar graph xXXXXXXXXXXXXXXXXXXXXXXXK
BATTERS JOYSTICK VERTICAL: xxH XXXXXXXxX bar graph XXXXXKXXXXXXXXXXXXXXXXXX
PITCHING JOYSTICK HORIZONTAL: xxH XXXXuXXX bar graph XXXXXXXXXXXXXKXKXXKXXXKX
PITCHING JOYSTICK VERTICAL: xxH XXXXxXxXx bar graph XXxXXXXXXXXXXXXXXXXXXXXX
PRESS THE PLAYER 2 OR SERVICE SWITCH BUTTON TWICE TO EXIT
b. PROCESSOR MEMORY TEST
The processor memory test checks all on-board RAM and EPROM memory with the exception of the video memory. The messages TESTING MASTER ROM, TESTING MASTER RAM, TESTING COLOR RAM and TESTING SLAVE MEMORY will each appear on the left side of the screen as each of those tests are performed. The result of each test (pass or fail) is displayed on right side of the screen next to the description of that test.
Two error messages may appear during slave memory test, these are COMMUNICATION ERROR and SLAVE NOT RESPONDING. ICs to be checked, in order of priority, are listed below:
COMMUNICATIN ERROR - a. U19 b. U21 through U23 c. U45 d. u60 e. U62 £. U64
SLAVE NOT RESPONDING - a. U10 (slave RAM) b. U3 (EPROM) c. U1 (280 CPU) d. U2 e. U20, U18 £. U61, U63
In the case of a failure of a ROM or RAM, the location (U number) of the suspected part is shown on the screen.
The following is an example of the display indicating a U107 failure.
PROCESSOR MEMORY TEST
| TESTING MASTER ROM | MASTER ROM | BAD |
CHIP 107 SUSPECT
| TESTING MASTER RAM | MASTER RAM | GOOD |
| TESTING COLOR RAM | COLOR RAM | GOOD |
TESTING SLAVE MEMORY SLAVE ROM
SLAVE RAM
PRESS 2-PLAYER START TO EXIT TESTING
VIDEO ALIGNMENT DISPLAY
Three video alignment screens are provided to aid in adjusting the game's video monitor for maximum picture quality. Refer to the video monitor technical manual (not supplied) for technical information and adjustment instructions.
The first screen consists of a white crosshatch pattern. This should be used to adjust screen position, horizontal size, vertical size and focus. Pressing the two-player start button advances the display to the next alignment screen.
The second alignment screen is used to adjust the red and green intensity. An eight level (0-7) color scale is shown for each red and green. The monitor should be adjusted so that level zero is black and one through seven appear as seven distinct levels.
The third alignment screen shows a four level blue color scale. Adjust the blue intensity so that level zero is black and levels one through three show as three distinct shades of blue. Eight other colors are also displayed for reference, they are, from 0 through 7 respectively: blue, green, red, cyan, magenta, yellow, gray and white.
VIDEO MEMORY TEST
The video memory test checks the foreground video memory. The test appears as a series of colored bars moving across the screen. After each pass (about 5 seconds), the results of the test will be displayed on the screen.
BASEBALL,
10. THE SEASON II - INSTALLATION & MAINTENANCE MANUAL
If the test was successful (all RAMs good), the message "VIDEO RAM CHECKS OK" will be displayed for about 1 second and the test will be repeated. Pressing the two-player start button anytime during the test will abort the test and return you to the diagnostic menu.
If the memory test fails, the message "VIDEO RAM TEST FAILED" will be displayed along with the location (U number) of the suspect RAM. In the event that the video error display is unreadable, a series of tones will also indicate the suspect chip (see table below).
NUMBER OF
AUDIBLE BEEPS SUSPECT ICs
2 U35 and U36 4 U33 and U34 6 U48 and U49 8 U46 and U47
e. VIEWING BACKGROUND SCREENS AND BACKGROUND TEST
This test is set up to view all the background screens by pressing the one-player start button to advance the screens. Pressing the two-player start button exits the program.
An example of the display is as follows:
BACKGROUND PROM TEST
PRESS 1-PLAYER START TO ADVANCE. OR PRESS 2-PLAYER START TO EXIT.
GAME SET-UP
The game option set-up section allows the operator to change various game options. As explained in previous sections, the one-player start button selects and highlights the desired function and the two-player start button enters or executes the function.
a. COINS PER CREDIT / CREDITS PER COIN
The coinage of each mech may be set to require multiple coins for each credit or give multiple credits for each coin.
To change coinage, follow the example screens below: (all examples assume 1 coin=25 cents)
For 25 cent play: 1 COIN FOR 1 CREDIT
For 50 cent play: 2 COINS FOR 1 CREDIT
Two plays for 25 cents: 1 COIN FOR 2 CREDITS
b. EXTRA PLAY
An option is included to award an extra play for the insertion of multiple coins before the game is started.
For example, if the coinage is set as follows:
1 COIN FOR 1 CREDIT EXTRA PLAY FOR 2 CREDITS
then the result will be, 1 coin will give 1 credit and 2 coins will give 3 credits. Each additional coin will add one credit.
Cc. ATTRACT MODE SOUND
This option, when selected, enables the game sounds during the attract mode.
An example of the display is as follows:
GAME SET-UP
SELECT FUNCTION WITH ONE PLAYER START BUTTON ENTER FUNCTION WITH TWO PLAYER START BUTTON
COIN MECH 1 1 COIN FOR 1 CREDIT NO EXTRA PLAY
COIN MECH 2 1 COIN FOR 1 CREDIT NO EXTRA PLAY
TWO PLAYER INNING FOR 1 CREDIT _ _ ATTRACT MODE SOUND
RETURN TO MAIN MENU
11.
12. GAME STATISTICS
Game statistics are provided to aid the operator in setting up his game for maximum profit.
The operator may reset the game statistic counters by selecting the "reset game statistics" function.
An example of the display is as follows:
GAME STATISTICS
SELECT FUNCTION WITH 1-PLAYER START BUTTON ENTER FUNCTION WITH 2-PLAYER START BUTTON
NUMBER OF 1-PLAYER INNINGS: PLAYER WINS: COMPUTER WINS: coo
NUMBER OF 2-PLAYER INNINGS: 0 COMPLETE GAMES BOUGHT: 0
RESET GAME STATISTICS
RETURN TO MAIN MENU
INNING DURATION GRAPHS
Graphs are provided which indicate the duration of one and two player innings. Average play time is also displayed. These graphs may be reset by selecting the reset options located at the bottom of the screen,
An example of the display is as follows:
INNING DURATION GRAPHS
SELECT FUNCTION WITH ONE PLAYER START BUTTON ENTER FUNCTION WITH TWO PLAYER START BUTTON
ONE PLAYER INNINGS: AVERAGE TIME: 0:00
0:00-1:00 1:00-1:30 1:31-3:00 3:01-5:00 xxxx bar graphs follow xxx
1-15:00 15:01-20:00 20:01-25:00 25:01-30:00 30:01-UP :01-10:00 0
it)
TWO PLAYER INNINGS: AVERAGE TIME: 0:00
0:00-1:00 1:01-3:00 3:01-5:00 xxxx bar graphs follow xxx
5:01-10:00
15:01-20:00 20:01-25:00 25:01-30:00 30:01-UP
13. 10:01-15:00 0
RESET 1-PLAYER INNINGS AND BAR GRAPHS RESET 2-PLAYER INNINGS AND BAR GRAPHS RETURN TO MAIN MENU
ERASE ALL PLAYER STATISTICS
BASEBALL, THE SEASON II will store player statistics for 300 players in battery backed-up memory. To clear these statistics select the ERASE ALL PLAYER STATISTICS option from the menu shown below. Similarly the top player lists may be erased by selecting that option.
An example of the display is as follows:
ERASE ALL PLAYER STATISTICS
SELECT FUNCTION WITH ONE PLAYER START BUTTON ENTER FUNCTION WITH TWO PLAYER START BUTTON
ERASE ALL STATS ON EXIT? NO ERASE TOP PLAYER LISTS ON EXIT? NO
RETURN TO MAIN MENU
D. SYSTEM TROUBLESHOOTING GUIDE
The entire Cinemat game system can be broken down into major groups. A brief guide to troubleshooting each section follows:
1. Input/Output functions:
a. Monitor
- No raster (i.e. black screen)
a. Check AC supply to monitor. If there is no power at the monitor, trace the
BASEBALL, THE SEASON II - INSTALLATION & MAINTENANCE MANUAL
wiring back to the isolation transformer and/or verify that power is reaching the transformer.
b. Check monitor fuses.
Display scrolls (apparent syncronization problem).
a. Check monitor alignment adjustments.
b. Check RGB and syncronization signals on PCB connector and trace through to the monitor.
Black screen
a. Check for +5.0 VDC at circuit boards.
b. Check connectors are securely seated and in the proper position,
White or checkerboard screen.
a. Check for +5.0 VDC on P4 - 3 through 7. If any of these signals are low, replace U114 (74LS08). If this fails, replace U119 (74LS257).
be Check the clock signal on the master Z80 (U99-6), BASEBALL, THE SEASON II I/O and Memory Expansion Board (U13), REDLINE RACER Sound Board (U14).
c. Check reset on the 280 (U99-26). This signal should normally be high and go low when the reset button is pressed.
White or red vertical lines close together on entire screen or half of screen.
a. Check video RAMs U33 through U36 and U46 through U49. Refer to sheet 11 and 18 on schematic.
Vertical lines on playing field (background).
a. Check signals on U81 through U83 (74LS166's).
b. Regarding other background problems, check the position of JP2 Jumpers, swap u56, (74LS461) with U60, see if problem disappears.
White vertical bars, usually on half of screen
sometimes with an audio buzz.
a. Caused by excessive temperature. Swap U45 with U23 and/or U60 with U22 (74LS461's).
- Intermittent flashing video or color changes.
a. Check for +5.0 VDC at circuit boards. TP1 and TP2 (+5 VDC)
- Picture freezes.
a. Check for +5.0 VDC at circuit boards, TP1 and TP2 (+5 VDC)
b. Check 2Z80s (U1 and U99). They should be Zilog Mostek devices with a "B" suffix (6 MHz). If not call for replacement.
e. Check for damaged sockets on master EPROMs and master CPU.
- Drifting pattern (any color).
a. Check connector and signals on Pl.
b. Sign of synchronization problems. Check DCLK.
c. Check U40 (RGSO9), U42 (RGSO7), and U43 (RGSO8) .
b. Buttons, joysticks and coin counters.
- A careful visual inspection of the buttons, harnesses and connectors is advised.
a. Inspect harness crimps.
b. Check for broken wires.
Cc. Check for broken solder joints at the
termination point.
- Trace signals through back to the input IC on the PCB.
- Electronics
a. Main board electronics.
- Problems can sometimes be traced to a bad CPU or crystal. Check the master and slave CPU's and their associated components.
- Check EPROMs for background and foreground display and the associated video timing logic.
BASEBALL, THE SEASON II - INSTALLATION & MAINTENANCE MANUAL
- Check power at the ICs.
Add on board(s) that control game specific functions.
- Again, check for functions specific to the board.
- Check all ICs for proper socket installation.
c. Check power at the ICs.
General Knowledge
a. Proper voltage input jumpering on the board is critical! Follow the instructions on this carefully. A symptom of improper jumpering is an audio buzz or no audio. Check for 12.0 to 15.0 VDC at U122-5 (audio amp). Refer to Power Supply Modification section of manual. NOTE: If your speaker is not connected, you will not hear any sound! Seriously, try adjusting the audio volume control pot (VP1). See section B above on adjusting the volume.
b. Game powers up with garbage on the screen - no buttons function - audio may buzz
Le Remove P4 and P5 and reset system (push button on main board). If picture appears, the problem may be a stuck coin switch, button or bad harness or ground connection,
- Visually inspect connector crimps and wire colors.
- Check for + 5.0 VDC at board.
Cc. A word about coin counters:
Do not use mechanical coin counters in any kit or dedicated game. These devices produce an inductive "kick" that will damage components on the circuit board(s). Problems caused by this are checkerboard video. A quick check to see if this is your problem is look at the "NMI not" signal on both Z80s (pin 17). If a low output is observed, try replacing U114 (74LS08) or if needed, U119 (74LS157).
The bookkeeping on our games is very accurate and includes number of coins dropped and dollars earned.
If you must install a coin counter, the next page shows a simple hookup using diode protection.
COIN COUNTER SURGE PROTECTION CIRCUIT FIG. 8
- IF YOU MUST INSTALL A COIN COUNTER
COIN SWITCH
COIN COUNTER
Ph-h OR Ph-7 +5V
DIODE MAY BE 1N4001 THROUGH 1N4003
BASEBALL THE SEASON II,
FROM CONNECTOR PIN # SIGNAL DESCRIPTION CONNECTOR PINOUT CHART
TO CONNECTOR PIN #
Pl-1 NOT USED
| P1-2 | MONITOR,~H SYNC | GRAY |
| P1-3 | MONITOR,-V SYNC | WHITE |
| Pi-4 | MONITOR, GROUND | BLACK |
| P1-5 | MONITOR, RED | RED |
P1l-6 POLARIZING KEY
| P1-7 | MONITOR, GREEN | GREEN |
P1-8 NOT USED
P1-9 MONITOR, BLUE BLUE
P1-10 NOT USED
| P2-1 | SPEAKER GROUND | SPEAKER | GRAY |
| P2-2 | SPEAKER GROUND | SPEAKER | WHITE |
| P3-1 | +5 VOLTS | J2-1 | RED |
| P3-2 | +5 VOLTS | J2-2 | RED |
| P3-3 | +5 VOLTS | J2-3 | RED |
P3-4 POLARIZING KEY (OPTIONAL) J2-4
| P3-5 | GROUND | J2-5 | BLACK |
| P3-6 | GROUND | J2-6 | BLACK |
| P3-7 | GROUND | J2-7 | BLACK |
| P3-8 | GROUND | J2-8 | BLACK |
| P3-9 | J2-9 | BROWN | |
| P3-10 | +12 OR 25 VOLTS | J2-10 | ORANGE |
PA-1 NOT USED
| P4-2 | GND, COIN, SERVICE | COIN DOOR | BLACK OR GREEN |
| P4-3 | TWO PLAYER START | CONTROL PANEL | VIOLET |
| P4-4 | NORMALLY OPEN | COIN SWITCH 2 | ORANGE |
| P4-5 | NORMALLY OPEN | SERVICE SWITCH | YELLOW |
| P4-6 | ONE PLAYER START | CONTROL PANEL | WHITE |
| P4-7 | NORMALLY OPEN | COIN SWITCH 1 | BLUE |
P4-8 NOT USED P4-9 NOT USED P4-10 NOT USED
P5-1 NOT USED
| P5-2 | GROUND | CONTROL PANEL | GREEN |
| P5-3 | GO BACK (N.O.) | CONTROL PANEL | GRAY |
| P5-4 | RUN/CUTOFF (N.O.) | CONTROL PANEL | BROWN |
| PS=5 | EXTRA BASE (N.O.) | CONTROL PANEL | BLUE |
| PS-6 | RUN/AIM (N.O.) | CONTROL PANEL | YELLOW |
| P5-7 | RUN/STEAL OUTER (N.O.) | CONTROL PANEL | ORANGE |
P5-8 NOT USED
| P5-9 | RUN/STEAL INNER (N.O.) | CONTROL PANEL | RED |
P5-10
P6 NOT USED XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXKKXXXXXXXXXXXXXXXXXXXXXXXXXX INPUT/OUTPUT AND MEMORY EXPANSION BOARD CONNECTORS:
BASEBALL THE SEASON II,
FROM CONNECTOR PIN #
J1-1 J1-2 J1-3 J1-4 J1-5 J1-6 J1-7 J1i-8 J1-9 J1-10
J2-1 J2-2 J2-3 J2-4 J2-5 J2-6 J2-7 J2-8 J2-9 J2-10
J3
J4-1 J4~-2 J4-2 J4-3 J4-4 J4-5 J4-6 J4-7 J4-8 J4-9 J4-10 J4-11 J4-12
J5-1 J5-2 J5-3 J5-4 J5-5 J5-6 J5-7 J5-8 J5-9 J5-10 J5-11 J5-12 SIGNAL DESCRIPTION
+5 VOLTS +5 VOLTS +5 VOLTS POLARIZING KEY GROUND GROUND GROUND GROUND NOT USED +12 OR +25 VOLTS
+5 VOLTS +5 VOLTS +5 VOLTS POLARIZING KEY GROUND GROUND GROUND GROUND
+12 OR +25 VOLTS
NOT USED
GROUND +12 VOLTS +12 VOLTS NOT USED SWING UP-DOWN NOT USED BALL SPEED NOT USED NOT USED CURVE POLARIZING KEY GROUND
GROUND DATA LINE 13 +5 VOLTS CLOCK RES 3 RES 2 DATA LINE 12 DATA LINE 3 DATA LINE 2 POLARIZING KEY SPARE NOT USED CONNECTOR PINOUT CHART
TO CONNECTOR PIN #
POWER SUPPLY POWER SUPPLY POWER SUPPLY
POWER SUPPLY POWER SUPPLY POWER SUPPLY POWER SUPPLY
POWER SUPPLY
P3-1 (MAIN P3-2 LOGIC P3-3 BOARD) P3-4 P3-5 P3-6 P3-7 P3-8 P3+9 P3-10
BATTERS JOYSTICK BATTERS JOYSTICK PITCHERS JOYSTICK
BATTERS JOYSTICK BATTERS JOYSTICK
PITCHERS JOYSTICK
PITCHERS JOYSTICK
PITCHERS JOYSTICK
TAG PCB J1-2 TAG PCB J1-7 TAG PCB J1-1 TAG PCB J1-5 TAG PCB J1-4 TAG PCB J1-3 TAG PCB J1-6 TAG PCB J1-10 TAG PCB J1-9
TAG PCB J1-8 BLACK BLACK BLACK BLACK
ORANGE
RED RED RED
BLACK BLACK BLACK BLACK BROWN ORANGE
GREEN ORANGE ORANGE
YELLOW BROWN
VIOLET
BLUE
GREEN
GREEN BROWN RED BLACK VIOLET ORANGE GRAY YELLOW BLUE
WHITE
BASEBALL THE SEASON II, CONNECTOR PINOUT CHART’
FROM TO CONNECTOR SIGNAL CONNECTOR WIRE
| PIN # | DESCRIPTION | PIN # | COLOR |
XXXXXXXXXXXXXXXXXXXXXXXXKXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXKXXKAXKAK INPUT/OUTPUT AND MEMORY EXPANSION BOARD 40 PIN RIBBON CABLE CONNECTOR:
| J7TA-1 | MASTER ADDRESS LINE 11 | ug99-1 (MAIN |
| J7TA-2 | MASTER ADDRESS LINE 12 | ug9-2 LOGIC |
| JTA-3 | MASTER ADDRESS LINE 13 | U99-3 BOARD) |
| UTA-4 | MASTER ADDRESS LINE 14 | u99-4 |
| JTA-5 | MASTER ADDRESS LINE 15 | ug9-5 |
| J7TA-6 | CLOCK | uUS9-6 |
| JTA-7 | MASTER DATA LINE 4 | u99~-7 |
| JTA-8 | MASTER DATA LINE 3 | u99-8 |
| JTA-9 | MASTER DATA LINE 5 | u99-9 |
| JTA-10 | MASTER DATA LINE 6 | ug99-10 |
| J7A-11 | +5 VOLTS | ug99-11 |
| JTA-12 | MASTER DATA LINE 2 | ug9g-12 |
| STA-13 | MASTER DATA LINE 7 | ug99-13 |
| J7A-14 | MASTER DATA LINE 0 | ug9-14 |
| J7TA-1i5 | MASTER DATA LINE 1 | u99~-15 |
| JTA-16 | INT | ug99-16 |
| JTA-17 | MNMI | u99-17 |
| J7A-18 | NOT USED | u99-18 |
| JTA-19 | MREQ | u99-19 |
| JTA-20 | I/O REQ | u99-20 |
| JTA-21 | RD | u99-21 |
| JTA-22 | WR | U99-22 |
| JTA-23 | NOT USED | U99-23 |
| JTA-24 | WAIT | u99-24 |
| JTA-25 | +5 VOLTS | ug99-25 |
| JTA-26 | POR | U99-26 |
| JTA-27 | M1 | U99-27 |
| JTA-28 | RFSH | U99-28 |
| JTA-29 | GROUND | ug99-29 |
| JTA-30 | MASTER ADDRESS LINE 0 | u99-30 |
| JTA-31 | MASTER ADDRESS LINE 1 | u99-31 |
| JTA-32 | MASTER ADDRESS LINE 2 | U99-32 |
| JTA-33 | MASTER ADDRESS LINE 3 | U99-33 |
| JTA-34 | MASTER ADDRESS LINE 4 | Uug99-34 |
| JTA-35 | MASTER ADDRESS LINE 5 | ug99-35 |
| JTA-36 | MASTER ADDRESS LINE 6 | u99-36 |
| JTA-37 | MASTER ADDRESS LINE 7 | U99-37 |
| J7A 38 | MASTER ADDRESS LINE 8 | Uu99-38 |
| JTA-39 | MASTER ADDRESS LINE 9 | u99-39 |
| JTA-40 | MASTER ADDRESS LINE 10 | u99-40 |
J7B NOT USED
CGIN COUNTER SURGE PROTECTION CIRCUIT
- ZF YOU MUST INSTALL 4 COIN COUNTER
COIN COUNTER
Pha OR Ph-7 +5V
DIODE MAY BE 1N4001 THROUGH 1NhLO03
FIG. 8