Space Odyssey
Space Odyssey (version 2) (Sega, 1981) · Manual · 78 pages · 14 sections · original scan
SEGA / ‘Gremlin
Owner’s Manual
Manual Part No. 420-0610
dce Nousseur
Owner’s Manual
Manufactured SEGA /Cremlin TLX 910-335-1621
SPACE ODYSSEY OWNER’S MANUAL Copyright © 1981 by SEGA®/Gremlin®, All Rights Reserved
table of contents
Introduction ....... 0. ccc ccc eee cc teen en eee eens 1 Game Concept. ..... 0... cece cece een nee eens 3 Game Set-Up and Inspection ..........0..0 eevee ee eee 5 G-80 Theory of Operation. ........ 0.00. c ccc ccc eee 9 Maintenance ProcedureS ......... 0. ee cence ee ees 15 Game Adjustments ...... 00. eee 21 Parts Catalog. ... 0... c cece cece cette ee eens 25 Schematics 0.0... e eee c nee e ee tenes 55
introduction
Space Odyssey is an electronic game that makes extensive use of digital circuitry and television monitor concepts. This manual is designed for the maintenance technician who possesses a general knowledge of solid state circuitry, microprocessor and digital integrated circuiry, and TV monitor concepts. Any individual not knowledgeable in these areas should not attempt repair of the electronic portion of the game. Gremlin’s new G-80 system makes troubleshooting easy. Each board has a separate function and most problems can immediately be isolated to a single board. The individual boards contain less circuitry than if they were combined on one or two boards. This results in faster and easier servicing. The new G-80 system gives Gremlin a lot more flexibility in designing new games. If you have any questions not answered in this manual, call SEGA/Gremlin Customer Service, (800) 854-1098.
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
game concept
Space Odyssey is a one or two player game in which a player tries to destroy enemy aliens in seven sectors. A player proceeds through seven sectors of cosmic cities and space mountains. A player maneuvers through the sectors by moving a joystick in eight different possible directions. Up or down in the horizontal mode, left or right in the verticle mode. The diagram shows the variable speeds and direction of movement.
HORIZONTAL SCENE
UP UP AND UP AND SLOWER FASTER
LEFT AND RIGHT AND SLOWER FASTER
LEFT AND SLOWER DOWN y AND FASTER
DOWN
VERTICAL SCENE
UP AND FASTER LEFT AND RIGHT AND FASTER FASTER
LEFT RIGHT
LEFT AND SLOWER RIGHT AND SLOWER
DOWN AND SLOWER SCORING As a player proceeds through the sectors, the higher the sector, the higher the possible scores that can be obtained by destroying UFO’s. Sector 1- 100-900 points can be obtained Sector 2- 200-900 points can be obtained Sector 3- 300-900 points can be obtained etc. If a player’s ship crashes into a UFO, the ship is lost, but the player is awarded the points for destroying the UFO. If a player’s ship is destroyed by a UFO bulletno change in score occurs. When a player’s ship explodes, a new ship appears in the present sector until all the player’s ships are destroyed. Bonus points called “Distance Points” are awarded for the successful completion of each round.
GAME ACTION As players enter each new sector they encounter enemy aliens. Players must avoid the mountains because they will destroy the ship. If a player enters a black hole they remain there for three seconds ina whirlpool. The faster a player goes, the more bonus points a player receives. In a two player game, players alternate after the destruction of each ship. The game ends when all ships are destroyed.
game set-up and inspection
- Inspection
- Before plugging in your new game, inspect it closely to spot any possible shipping damage. Check to ensure the graphics are in place, the monitor is not damaged and that the overall cabinet is in good condition condition.
Figure |
- Open the coin mechanism door (see figure
- and inspect the inside of the game electronics compartment. Be sure no components or connectors have come loose. Proper connector fittings must be checked before game power is applied. Check all related connectors for good contact. Although disconnected connectors are easily spotted, poor contacts are difficult to locate. The connectors should therefore be pushed in firmly and then loosened to spot poor connections.
- Are the fuses intact? There are five fuses (not counting the monitor fuses which are detailed in the monitor manual for this game). One fuse is located on the AC junction box. The other four are on the power supply PC board. See figure 2.
Figure 2
- Voltage Selection Before plugging in your game, make sure that the game voltage is correct for your location. Locate the two leads from the AC junction box to the power transformer. For 110 VAC, they should be connected to terminals 1 and 3 on the power transformer. For 100 VAC, connect 1 and 2, and for 220 VAC applications, they should be connected to 1 and 4. See figure 3.
| 7 | 7 | i |
| 2 | 2 | 2 |
| 3 | 3 | 3 |
| 4 | 4 | 4 |
| to0v | 10v | 220V |
Figure 3 You will also notice on the AC junction box that there is a safety interlock switch. When the front panel is in place, the switch is depressed and the game receives power. Removing the front panel, the switch returns to its original position and the power is cut off from the game. For servicing, this switch can be pulled out and power will be restored. See figure 4.
Van) Safety Interlock Switch
Figure 4
- Game Specifications
100 VAC, 60 HZ (nominal), 150 watts max 110 VAC, 60 HZ (nominal), 150 watts max 220 VAC, 60 HZ (nominal), 150 watts max Dimensions 25% inches wide X 30% inches depth (64.8 cm wide X 76.8 cm depth) 72% inches height (184.2 cm height)
- Important Notes
- The following note is included in compliance with FCC rules: WARNING: This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual, may cause interference to radio communications. As temporarily permitted by regulations, it has not been tested for compliance with the limits for Class A computing devices pur- Power suant to Subpart J of Part 15 FCC Rules, which are designed to provide reasonable protection against interference in which case the user at his own expense will be required to take whatever measures may be required to correct the interference.
- Miscellaneous Never remove circuit board connections while power is on. Never replace any components with anything other than exact replacement parts. DO NOT replace fuses with anything other than the proper value. A blown fuse indicates an overload condition within the game. Replacing the fuse with a higher value can cause severe damage to internal components, if an overload occurs. Correspondence regarding this should be addressed to: SEGA/Gremlin 8401 Aero Drive San Diego, California 92123 ATTN: Customer Service (800) 854-1098 game
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
G-80 theory of operation
Game Block Diagram
MEMR PROGRAM MEMORY MASTER TIMING (EPROM)
DATA
> 7 VIC CHIP:
- MONITOR TIMING. D) ADDRESS MULTIPLEXERS COMPOSITE SYNC
2 sf avoress
VIDEO (SCREEN)
MEMORY (RAM) aK x 8
DATA IN
x
WRITE (OUT)
INPUT PORT
COIN PLAYER ‘SWITCH CONTROLS OUTPUT PORT
SOUND BOARD DATA OUT LINES
MEM W
MICRO- MID R PROCESSOR 2608 READ (IN)
DATA BUS e
8 8
COMPOSITE SYNC
POWER LOAD SR, ELOes! “VIDEO SHIFT REGISTER
Biw VIDEO OUT
COLOR GENERATION
Background Generator
COLOR MONITOR
- DENOTES CIRCUITRY CONTAINED IN VIC CHIP.
- G-80 Boards: The G-80 system consists of five boards that plug into a mother board. They are the CPU, Background Generator, Sound, Video and EPROM boards. They plug into the mother board in a card cage system to simplify repairs and cut down on interference to outside communications systems. The mother board is cross-wired to allow for the boards to be plugged-in in any order. Listed below are the bus pin assignments on the mother board:
| 1 | Ground | A | Ground |
| 2 | AI5 | B | AT |
| 3 | Al4 | Cc | A6 |
| 4 | Al3 | D | AS |
| 5 | Al2 | E | A4 |
| 6 | All | F | A3 |
| 7 | Al0 | H | A2 |
| 8 | AQ | J | Al |
| 9 | A8 | K | AO |
| 10 | D7 | L | D3 |
| 11 | D6 | M | D2 |
| 12 | DS | N | D1 |
| 13. | ~D4 | P | DO |
| 14. | WAIT | R | RESET |
| 15 | INT | Ss | EDGINT |
| 16 | NMI | T | EXT |
| 17. | EXT?SEL | U | ® OUT |
| 18 | MEMR | Vv | MEMW |
| 19 | INPUT | W | OUTPUT |
| 20 | RFSH | xX | MREQ |
| 21 | INTACK | Y | AC |
| 22. | «+5V | Z | +5V |
| 23. | «+5V | a | +5V |
| 24 | —5V | b | —5SV |
| 25. | +12V | c | +12V |
| 26 | —12V | d | —12V |
27 e
| 28 | HALT | f | MI |
| 29 | 8/2 | h | * |
| 30. | —* | j | = |
| 31 | SRC | k | * |
32 1 33 m 34 n 35 p 36 T 37 s 38 t 39 u NSM g<
44 Ground Ground *For Development Purposes Only
- CPU Board (Refer to CPU Schematic, sheets 6 and 7)
The CPU board is completely timed with the video board. But, for testing purposes it contains its own clock circuit, powered by an 8.000 MHZ crystal. Pin 17 is the external clock select and is grounded when the video board is plugged in. When the external clock pulse comes in through pin T, it goes directly to the CPU and the entire CPU clock circuit is disabled. The WAIT signal, entering in at pin 14, is used to synchronize slower memory accessed by the CPU. The NMI circuit, entering in at pin 16, contains a switch for activating the built-in self-test. The self-test system will be explained more fully later. When the edge interrupt circuit, entering at pin S, goes LO, it triggers an interrupt in the CPU. The CPU stops whatever it is working on, completes the activity required by the interrupt, and then returns to the function it was performing prior to the interrupt. It is a negatively triggered interrupt, which can be disabled by the CPU at any time. The AC signal, entering in at pin Y, combines with RESET at pin R and the input from the reset switch located on the operator panel to reset the CPU. Disregard PANEL RESET at pin 30. This circuit is used only for system development. The CPU in Space Odyssey is a Z80A. You must always use a Z80A as the Z80 is not fast enough to run the game. U21 is an address bus controller. Eight of the sixteen address lines pass through U21 before addressing the RAMs and the Eprom at U25. U25 contains the data for the self-test and contains features common to all games, such as coin acceptance, credit/coin handling, power-up sequence, player 1 or 2 recognition and CPU initialization. U3 is an output
port for the CPU and U4 is the input port. Connector P1, pins 23 through 40, shown on sheet 6 is not used in Space Odyssey. U15, located below U4 on the schematic, decodes memory select on the CPU board. Sheet 7 contains the coin inputs, player inputs and inputs from the operator panel. The coin circuitry contains ICs U6, U39 and U16. U9 is the input port for the coin switches and service switch. Player inputs enter through connector P1, pins 15 through 22.
- Video Board The video board contains a VIC chip used in previous games (U58). The video board also contains a 15.468 MHZ crystal that generates the timing signals for video generation. Because the video board contains twice as many RAMs, as used in previous game boards, it has a more extensive graphics capability. Color capability is greatly expanded because of a color RAM, U9, which allows the program to create a wider variety of color schemes. There are 8 shades of red, 8 shades of green, and 4 shades of blue. The video board also contains circuitry (U34, U35, U36, U38, U49 and USO) to make the picture “flip” for cocktail table models. On the G-80 video boards for Space Odyssey, a small sub-board, called the HARDWARE SHIFTER, is mounted in socket U12. This board speeds up the generation of video information on the screen. Normally, character generation is performed by the microprocessor. However, in order to speed up character movement, we cannot just speed up the microprocessor. So, the speed increase must be performed by the Hardware Shifter circuit. It does this by shifting data from the CPU and feeding it directly to video RAM. The shifter circuit, then, drastically reduces the number of software operations the CPU would have to perform to do the same thing. As game play becomes more sophisticated, increased speed of movement is a vital element of this sophistication, On some G-80 Video I Boards, you will see the VIC Replacement Board. This board is, in part, the equivalent circuit of the VIC chip. It is a simple circuit consisting of a number of counters and multiplexers for generating video timing and addressing video RAM.
- EPROM Board The EPROM board contains a relatively simple memory system. It can hold up to 23 2716 EPROMs totalling 46k bytes of memory (1 byte equals 8 bits). U24 and U30 decode all the EPROMs; U25 is the buffer IC to the data bus. In operation, any one of 23 EPROMs is selected by 5 CPU address lines.
- Background Generator Board The Background Generator board is an additional circuit found in Space Odyssey. Its purpose is to produce the intricate and colorful displays ‘““behind”’ the game action on the screen. The board acts as a selfcontained color display system that generates a pre-programmed pattern on the screen; the display it produces is simply scrolled, or moved sideways, along with the game action. All the character information is stored in the board’s EPROMs, and the data from them is loaded into the banks of parallel-toserial shift registers, 74LS166s. These streams of serial data produce the RGB outputs which are tied to the RGB outputs from the G-80 VIDEO board. When no game characters are being displayed, the background video is allowed to pass to the color monitor; when the game characters are present, the background video is shut off. Of course, this action alternates fast enough that it is not noticeable on the screen. The background generator board senses the 8 outputs of U1 1 (74LS374) on the video board; these signals are connected to the Background board at pins 32 through 39. When these eight lines are high, the background generation is triggered into a display mode. Other elements of this board include monitor timing circuitry (2-74LS393 counters) for horizontal and vertical signals, and flip circuitry to invert the picture for cocktail tables. In addition, decoding IC’s U65 and U66 sense the G-80 address bus signals AO- A7 to enable the circuits of the Background Generator.
- Sound Board The Space Odyssey G-80 Sound Board contains the circuits needed to generate all game sounds other than the speech. The Sound Board circuits are triggered through latches IC43 and IC44 which are connected to the data bus. The appropriate 8-bit code on the data bus is latched by IC43 or IC44 to activate the corresponding sound circuit. All sound board signals are mixed by IC 7 and output at Pin 8. The final audio output is brought into the power supply amplifier.
- Power Supply The Game Power Supply (800-0128) incorporates all of the voltages and audio power amplification necessary to power Space Odyssey. In addition to the logic supply voltages available, 100 VAC and 115 VAC isolated supplies are available for the TV monitor and fluorescent lights. Also, multiple primary taps are available for using 100 VAC, 115 VAC, or 230 VAC as the input voltage. This supply was originally designed for use with the Dual Game Board or Dual Game VIC Board. Table 1 lists the ratings of the supply when all outputs are used simultaneously. This also happens to be a standard test load. These are worst case ratings (such as when the PROMS in use draw their maximum rated currents) and therefore are rarely encountered when driving the boards. TABLE 1
| +5V@ | 2A | = | 10W |
| —S5v@ | 1A | oad | SW |
| +12V@ | 1.5A | = | 18W |
| —12V@ | 1A | = | 12W |
MONITOR & LIGHT 100VAC or 115 VAC 715W
TOTAL 120W
The rating of the +5V supply can be safely increased to 3.5 amps if the load currents on the other voltages are reduced. This is necessary to prevent the heat sink and transformer temperatures from increasing to the point where reliability suffers.
- Circuit Description: The +5 volt supply consists mainly of U1 and QS. U1 is a 723 voltage regulator IC, which contains a voltage reference, error amplifier, series pass Darlington transistor pair and a current limit transistor. Potentiometer RS (+5V ADJ) divides the 7.15V (nominal) reference to 5.0 volts as the input to pin 5, the non-inverting input of the 723’s error amp. Pin 4, the inverting input, senses the output voltage. The internal error amp maintains a voltage at UI pin 10 which is higher than the 5.0 V output by an amount equal to the two VBE drops of Darlington Q5, which acts as a current amplifier, and the IR drop across R32. A foldback current limiter circuit is composed of R32, R2, R3, Q1 and the internal current limit transistor of U1. This circuit allows the regulator to operate normally until the load current increases to the point where the voltage across R32 reaches the value which starts “‘turning on” the internal current limit transistor reduces the output current of the regulator to a fraction of the “knee” current when the output is shorted to ground. This feature greatly reduces the power dissipated in Q5 when the output is accidently short circuited. This action occurs so quickly during a short that fuse F1 should not blow. The value of the “knee” current can be increased or decreased by decreasing or increasing R3, respectively. Capacitors C4 and C5 frequency compensate the regulator so it won’t oscillate, and Cl and C26 perform high frequency bypassing. QI is included for temperature compensation. Temperature variations of its emitter-base voltage closely match and cancel the base-emitter voltage of the internal current limit transistor. Therefore, the “knee” current of this regulator of about 6 amps stays quite constant over wide temperature variations. The short circuit current is less than 100 ma. The +12 volt regulator uses 7.15 volts as a reference. U2 compares this voltage with the voltage at the wiper of R23 (+12V ADJ). Darlington PNP Q6 is the series pass element: Transistor Q2 and current sense resistor R12 from the current limit
circuit to protect Q6 from excessive load currents. The trip point is about 3 amps. Resistor R10 shuts the circuit off even harder if the output is short circuited. Resistor R11 and electrolytic C7 form a low pass filter which prevents short current pulses from activating the current limit circuit. The —5V and —12V regulators utilize three terminal ICs, 7905 and 7912, respectively. Capacitors C2, C3, C11 and C14 bypass high frequencies so that U4 and US won’toscillate. The audio power amplifier is composed of op-amp U3 and transistors Q3, Q4, Q7 and Q8. U3 provides most of the voltage gain while the transistors supply most of the current gain. This amplifier differs from previous ones in that the output stage also exhibits a voltage gain of about 2 so that the output can swing close to both power supply rails. This allows this amplifier to supply 36 watts into 4 ohms and 24 watts into 8 ohms. These values will be less in the +12 volt or —12 volt supplies are loaded significantly and/or the line voltage is less than 115 VAC. The overall voltage gain of the circuit is set by the ratio of R20 and R28. The actual value is: R20 4 1= SOE +1 = 22.4 of 27 db Capacitor C13 determines the low frequency roll off (about 7 HZ) and forces the DC gain to be unity. Therefore, the circuit does not amplify DC voltage. The input impedance is 47k ohms and is direct coupled.
- Adjustments: i. Adjust R5 for 5.0V at the load. This compensates for wiring losses. Adjust R23 for 12.0V at the load. There are no adjustments for the —S5V or —12V supplies or for the amplifier. The values should be —5V +0.2V and —12V +0.5V. The second power supply, the switching regulator, is an efficient device that provides a regulated +5 voltage at a high current. A power transformer and circuit could do the same thing, but it is much less efficient. The following theory refers to the switching regulator part #601-0158; the schematic is included in the back of the manual. Basically, a switching regulator operates by switching a high voltage, low current input through an inductor and filter capacitor. The current through the inductor rises when the high voltage is applied. When the voltage is cut off, the falling current level is then switched again through the capacitor. The resulting output, which is dependent on the on-off periods of the switching action, isa regulated voltage much lower than the input voltage but at a higher current. Looking at the schematic, we see the 110 volt AC input applied to bridge rectifier D1. The filtered DC output is switched on and off through inductor T1 by transistor Q1. Transformer T1 is a step down type; its secondary output voltage then, is considerably less than the primary voltage. As the primary voltage is switched, the secondary current alternates through L1. When the current through LI falls negative, D3 switches on to pass the current to the filter capacitors, C9 and C10. The action occurs rapidly, and gives a 5 volt DC output. The 5 volt output is sensed by ICI which causes the pulse (switching) rate to vary and provides output voltage regulation. The pulsing output of IC1 switches transistor Q2 on and off which, in turn, switches transformer T2. The output of T2 is then applied to Ql. Transformer T2 is necessary to isolate the output side of the supply from the input side. Transformer T3 supplies the necessary DC voltages for the IC and its associated circuit. R2, C2, C3, CS, R4 and D2 serve as suppressors to absorb the switching spikes.
maintenance procedures
- Self-Test Space Odyssey contains a built-in selftest system, activated by depressing the red self-test switch located on the CPU board. If the cover to the G-80 card cage is in place, the switch can be activated by putting a pen or pencil through the hole provided on the cover. See figure 5.
Figure 5
- CPU Board RAM Test The first test performed is a CPU Board RAM test, for IC’s U26-U29. It is instantaneous and ends when the screen goes white. If there is a problem in the CPU Board, the test will not continue, and you must use standard troubleshooting techniques to isolate and repair the CPU Board. There is a red LED, called the Halt Light, located directly behind the self-test switch. When a problem on the CPU Board occurs, it will come on and remain lit.
e ft 00
- Video RAM Test The white screen is the beginning of the Video RAM test. If there is a problem, the screen displays: CPU VIDEO MEMORY FAILED
CHIP U19
It tells you exactly which chip is defective. The rest of the test will not continue until the faulty RAM is repaired. If the video RAMs are functioning properly, the screen displays:
VIDEO MEMORY TEST PASSED
ce) Input Test The next sequence tests for errors in the input circuitry. The screen display is on the next page. INT in the upper left corner of the screen tests the interrupt circuits to the CPU. To be working properly, random characters should be displayed very rapidly to the right of INT. This shows the interrupt circuits are functioning properly. If the space to the right of INT remains blank, the CPU is not being interrupted properly. Dip Switch settings are displayed to verify the options selection. 1PSTART and 2PSTART will not be displayed on the screen initially. Depress the 1player and 2-player buttons alternately and they should appear on the screen. If not, then there is a problem in the circuitry associated with the 1 and 2 player buttons. The bottom of the screen displays Player Controls. To be functioning correctly, they should all display OFF, then as each switch is depressed, display ON.
INPUT TEST
INT DIP SWITCHES 87654321 100000000 2¢€¢c000000
1PSTART 2PSTART
PLAYER CONTROLS
| Pi | UP | OFF | ||
| Pl | Right | Pl | Right | OFF |
| Pl | Down | PI | Down | OFF |
| Pl | Left | Pl | Left | OFF |
| Pl | Fire | P2 = Left | OFF | |
| Pl | Bomb | P2 | Up | OFF |
| Pl | Up | OFF | ||
| Pl | Fire | OFF | ||
| Pl | Bomb | OFF |
- Coin Test This test checks the timing of the coin switch. Refer to the illustration below.To activate this test, insert coins into both coin mechs alternately. Coin mech 1 will appear on the screen as A and coin mech 2 will be displayed as B. Any letter appearing within the good area indicates the coin switches are timed properly. The closer the letter comes to either line, though, the more out of adjustment the coin switches are. Adjust a faulty coin switch by bending the trip wire up or down, slightly. To proceed to the next test, the 1-player button must be depressed.
COIN TEST
BAD BAD
- Eprom Test This test checks the EPROMS on the EPROM Board. Note the display above. The part number for each Eprom is displayed and whether that EPROM is good or bad. This is a fast test and will not remain on the screen long if none of the PROMs are bad.
=) __—__—_—, EPROM TEST
0941B Good 0942A Good 0943A Good 09444 Good 0945A Good 0946A Good 0947A Good 0948A Good 0949A Good 0950 Good 0951A Good 0952 Good 0953 Good 0954 Good 0955A Good 0956 Good 0957A. Good 0958A Good seme None seek None sepa None siete None setae None
- Screen Test This is a color test. You will see a white line around the entire screen and across the middle to divide the screen in half. In the upper half will be three color bars. The top one is blue, the middle is green and the bottom should be red. This test can be terminated by depressing the 1-player button.
- Sound Test The final phase displays each type of sound on the screen accompanied by the actual audio sound. It starts with display, ALL SOUNDS OFF, and continues through eleven different sounds. At the conclusion of the sound test, the game displays:
NO PART OFTHIS PROGRAM SHOULD BE USED WITHOUT PERMISSION Copyright 1981 SEGA ENTERPRISES, LTD.
The game then returns to the advertising sequence and the test is complete.
- Control Panel Removal With the door to the game electronics compartment open, reach under the control panel and flip the fasteners on both sides of the control panel. The control panel will now swing down as shown in figure 6. Disconnect the control panel connector. Now slide the spring-loaded pins on both sides to take out the control panel.
Spring-Loaded Pins |
- Front Bezel, Interior Graphics and Spacer Frame Removal The front bezel, which secures the interior graphics, is held in place by the control panel. Refer to figure 7. Unhook the fasteners on the control panel and swing it down. The front bezel can now be removed easily by lifting it on the bottom slightly and pulling it outward. Note that at the top of the bezel frame, there are two small pins to hold and align the bezel. The interior graphics can now be removed. Figure 7 also details the spacer frame which is located directly behind the interior graphics. It must be removed when taking out the monitor or replacing the panel logo. To remove the spacer frame simply pull on the four sides carefully and lift it out.
Figure 7
- Card Cage Removal If it is necessary to remove the card cage for servicing, first disconnect all the connectors. Then remove the three mounting screws shown in figure 8 and the card cage can be slipped from the mounting bracket underneath the cage.
ae \ Figure 8
- Panel Logo Removal First remove the front bezel, interior graphics and spacer frame as explained
Figure 9 previously. Underneath the panel logo and on either side of the speaker board you will see a sliding latch. Refer to figure 9. Using a screwdriver or your finger slide the latches on both sides to release the speaker swing panel. Push up on this panel to release the panel logo from its mounting slots. Refer to figure 10. With the panel logo removed, easy access is gained to the speaker and fluorescent lamp assemblies for servicing. To install the panel logo, release the two latches on the speaker swing panel, push the back of the board up and insert the lower edge of the panel logo in its slot. Then, push the front edge of the speaker swing panel up and, at the same time, push the panel logo in to seat the upper edge of the logo into its top slot. Once in place, close the latches to secure the speaker swing panel.
Figure 10
- Monitor Removal To remove the monitor for servicing or replacement, first open the back panel on the cabinet and disconnect the leads to the monitor. Then, remove the front bezel, interior graphics and spacer frame as explained earlier. Underneath the monitor in the game electronics compartment are four bolts securing the monitor in place. Refer to figure 11. Remove these, pull the monitor on either side and slide it out carefully.
Figure 11
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
game adjustments
- Operator Panel 2. Options Selection The operator panel is located on the inside The following charts define the game and of the coin door behind the coin mechanism. coin/credit options available for the Space It contains the volume control for adjusting Odyssey game. These options are controlled sound, a service switch for giving credits by 2 sets of switches (DIP) located in the without increasing the coin counter and a upper left hand corner of the G-80 CPU reset switch for resetting the game. card. Switch #1 is positioned close to the edge of the board; switch #2 is recessed.
SPACE ODYSSEY GAME OPTIONS — Switch #1
Game Option 6 Ships 5 Ships 4 Ships 3 Ships Extra Ship @ 80,000 PTS 60,000 PTS 40,000 PTS 20,000 PTS MK KK MMMM QaNSS KKMM QASAS KKK KS MM KK xa KKM oooo ooooe Cc
Cc
x x x xX
x x xxx ANSCCH
UPRIGHT COCKTAIL Plead xx ad ad alta!
COIN/CREDIT OPTIONS — Switch #2
Coin/Credit 4 coin/1 credit 3 coin/1 credit 2 coin/1 credit 1 coin/1 credit 1 coin/2 credit 1 coin/3 credit 1 coin/4 credit 1 coin/5 credit 1 coin/6 credit 2 coin/1 credit 4 coin/2 credit 5 coin/3 credit ononO0nOnOne aaoonnoonn.s aaq0oo0o0nqana oeoanaaaaanw onaonoanoNneons ANDAOANDONANY ANDWDOOANANAN oonnnanqaaane
COIN/CREDIT OPTIONS — Switch #2, Continued
Coin/Credit 8 7 6 5
2 coin/1 credit Cc fe) Cc fe) 4 coin/3 credit
1 coin/1 credit 2 coin/2 credit 3 coin/3 credit 4 coin/4 credit 5 coin/6 credit
1 coin/1 credit 2 coin/2 credit 3 coin/3 credit 4 coin/S credit
1 coin/1 credit 2 coin/3 credit
1 coin/2 credit 2 coin/4 credit 3 coin/6 credit 4 coin/8 credit 5 coin/11 credit
1 coin/2 credit 2 coin/4 credit 3 coin/6 credit 4 coin/9 credit
X = Don’t Care
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
parts catalog
1 Indicates Recommended top assembly Spare Parts—Stock Quantity Indicated To Support 5 Games.
PARTS LIST DWG NO. 700-0056 Gremlin Qty Per Part # Assembly | Description 130-0001 SPEAKER GAME 6x9 130-0002 SPEAKER COVER 6x9 140-0021 COVER J-BOX 140-0054 CABINET, UPRIGHT K-D 220-0019 LOCK, PANEL 220-0160 COIN MECH. 220-0167 LOCK,COINMECH.DOOR 220-0178 DRAW LATCH 250-0038 MOLDING STRIP 250-0048 CLIP SWITCH 250-0452 TEE MOLDING 250-0453 LIP MOLDING 250-0458 SADDLE G-80 CAGE 250-0467 COIN DOOR SUPPORT 250-0481 STRIKE PLATE 253-0201 COVER, HAND HOLD 253-0202 COVER, POWER CORD 253-0203 PANEL MONITOR K-D 253-0212 CASH BOX MODIFIED 253-0219 PANEL LOGO S/O 280-0005 CABLE TIE 280-0324 CABLE CLAMP NYLON 280-0327 BASE TIE WRAP 280-0360 WASHER LOCK, LOCK 390-0019 LAMP FLUORESCENT 420-0028 DECAL S/N 420-0030 DECAL CAUTION 420-0041 DECAL S/N SMALL 420-0486 MANUAL ELECTROHOME MON. 420-0568 DECAL FCC 420-0609 GRAPHIC INTERIOR S/O 420-0610 MANUAL SPACE ODYSSEY 420-0611 DECAL GAME INSTRUCTIONS 800-0147 ASSY. FLUORESCENT LAMP 2 800-0165 ASSY. MONITOR COLOR 800-0175 ASSY. VOL. CONTROL BLOCK 800-0179 ASSY. COIN COUNTER 800-0196 ASSY. HARNESS VIDEO 800-0217 ASSY. HARNESS SPEAKER 800-0230 ASSY. HARN. CONT. PNL. INTERFACE 800-0231 ASSY. HARN. GRND. COIN MECH. WOMADNERWN— BE ERE RR RRR ERR EEO RN BENE ENE NE ERE ENN NE EEE
REAR _VIEW ri % “al —)
SECTION £-E
eal FRONT VIEW Top Assembly 700-0056
SECTION C-C
SECTION A-A
Top Assembly—Continued
PARTS LIST
Tem Gremlin Qty Per Part # Assembly | Description 800-0232 800-0234 800-0236 800-0268 800-0269 800-0270 800-0271 800-3161 800-3165 800-0237 eee ee eee Moe ANA PEQEDRRD
f
a
SECTION B-B_ 1@® DWG NO. 700-0056
ASSY. HARN. GRND. INTERFACE ASSY. HARNESS MON. GRND. ASSY. HARNESS COIN MECH. ASSY. HARN POWER ASSY. J-BOX ASSY. PWR. SUPPLY ASSY. HARN. GRND. SWITCHER ASSY. GAME ELECTRONICS S/O ASSY. CONTROL PANEL COMP. ASSY. GRND. STRAP CONT. PANEL SCR PHIL PAN HD. #7x.75 PART BD. SCR PHIL PAN HD 8x.62 SHT. MTL. SCR PHIL PAN HD #10x.5 SHT. MTL. SCR BUGLE HD. #7x1.5 SCR SLOT HD. #8-32x1.5 MACH. SCR PHIL PAN HD. #10x1.25 SHT. MTL. WASHER FLAT #8 WASHER LOCK SPLIT #8 WASHER FLAT #10 WASHER LOCK SPLT #10 NUT HEX #8-32 NUT HEX #10-24 BOLT CARRIAGE #10-24x1 4 BOLT CARRIAGE #10-24x1.5 L.
———® [PIN 252-0106 REF.
ley
PIN 252-0122 A 2 FEQD. cer
N97 252-0123. PEF _DETAIL_E
Top Assembly 700-0056
control panel assembly
PARTS LIST DWG NO. 800-3165 Gremlin Qty Per
| Part # | — | Description | ||
| 1 | 240-0006 | BUTTON PLUNGER RED | ||
| 2 | 240-0007 | 3 | BUTTON PLUNGER, BLK. | |
| 3 | 250-0489 | 1 | SUBPANEL METAL WELDMENT 5/0 | |
| 4 | 253-0031 | 8 | SPACER, SWITCH | |
| 5 | 253-0220 | 1 | GRAPHIC CONTROL PANEL | |
| 6 | 280-0329 | 4 | NUT, HEX PAL 4-13 | |
| 7 | 280-0327 | 3 | BASE TIE WRAP | |
| 8 | 280-0005 | A/R | CABLE TIE | |
| a | 9 | 510-0058 | 1 | JOYSTICK 8 WAY LONG SHAFT |
| 14 | 510-0023 | 4 | ASSY. SWITCH | |
| 800-3166 | 1 | ASSY. HARN. CONTROL PANEL |
4 BOLT CARRIAGE No. 10-24x.75 L. 4 NUT, HEX No. 10-24 4 WASHER, LOCK No. 10
PARTS LIST
390-0083 211-0027
211-0044 211-0041 fluorescent lamp assembly
DWG NO. 800-0147
LAMP FIXTURE FLUOR 18” CONN. RING LUG #10 6-32x%” ROUND OR PN HD MACH. SCREW CONN CAP AMP 2 PIN CONN PIN AMP
PART OF (TEM 4
volume control block assembly
PARTS LIST DWG NO. 800-0175
- Gremlin Qty Per Part # pause Description
211-0005 CONN CRIMP LOCK 211-0042 ; CONN SOCKET AMP 211-0043 CONN PLUG AMP 2 PIN 211-0045 CONN PLUG AMP 6 PIN 211-0059 CONN PLUG AMP 3 PIN 212-0005 CONN FEM BLK 4 PIN 240-0001 KNOB VOL CONT 250-0462 VOL CONT BRKT 280-0005 CABLE TIE 420-0561 DECAL OPERATOR CONTROL 475-0007 POT 10K CAR PNL MT 510-0051 SW PUSHBUTTON SLIDE 600-0013 CABLE 1 COND SHLD POP RIVET %x” 470-0331 RESISTOR 330 OHM 4W 5%
© wovome | \votome | seavce [reser 1 : \ © ©
- Pe P7 Pe °0 |O!1®@|@
©
U UT y
SPL
PARTS LIST coin counter assembly
DWG NO. 800-0179 Item Gremlin Qty Per # Part # Assembly | Description CONN SOCKET AMP CONN AMP PLUG 4 PIN COUNTER DIGITAL 6 VOLTS CABLE TIE ELECTRIC CRIMP SLEEVE 24-18 AWG. 211-0042 211-0073 220-0008 280-0005 280-0362
junction box assembly
PARTS LIST DWG NO. 800-0269 Gremlin Qty Per Part # Assembly | Description 140-0020 JUNCTION BOX METAL 211-0038 CONN QUICK 3/16 FEM. 280-0361 BUSHING S/REL A.C. CORD 270-0001 FILTER EMI 280-0007 BUSHING S/REL % 280-0362 ELECTRIC CRIMP SLEEVE 24-18 AWG 510-0013 SWITCH SPDT CHERRY 514-0001 FUSE 2 AMP 250V S.B. 514-0005 HOLDER FUSE 600-0001 CORD LINE 3 COND. 211-0027 CONN RING LUG #10 600-0079 CORD LINE ZIP 280-0005 CABLE TIE SCREW 6-32x5/8 NUT HEX. HD. 6-32 WASHER, LOCK #6 INT. STAR STUD 8-32x1 NUT HEX. HD. 8-32 WASHER LOCK #8 INT. STAR SHRINK TUBING - % DIA WASHER FLAT 4” NUT HEX HD #10-24 BOLT CARRIAGE #10-24x1%” COIDAAWNE qo eee RRR Oe
N w oi
a RR EN WENNNN
dq
f
- 6-09 a WIRE
of "6 a
Junction Box Assembly 800-0269
cpu board assembly .
PARTS LIST DWG NO. 800-0107 Gremlin Qty Per Part # Assembly | Description Ref Des
| 150-0088 | CAP E 10uf 25V | C43, C45, C46, C62 |
| 151-0005 | CAP CER 680pf 50V | C50 |
| 151-0012 | CAP CER .1luf 50V | c47 |
| 151-0020 | CAP CER 33pf 50V | c49 |
151-0060 CAP CER .luf 16V AX | C37-C42, C44, C48 C51-C61, C63, C64 CAP CER 220pf 16VAX | C1-C36 PC. BOARD CONN PIN TEST PT TP1-TP4 CONN M 10 PIN RTA XTAL 8.000 MHZ IC NE555 U12 IC 7404 U30 IC 74LS00 U6, U8, U14, U19 IC 74LS04 U18 151-0061 170-0194 211-0008 212-0098 230-0013 314-0001 314-0015 314-0018 314-0019 314-0058 314-0055 314-0058 314-0062 a
IC 74LS244 U34, U36, U38 IC 74LS08 U13 IC 74LS74 U10, U11, U17, U20, U39 IC 74LS27 U16 IC 74LS30 U37 IC 74LS32 U32, U33 IC 7T4LS02 IC 74LS8240 IC 74LS14 IC 74LS139 IC 74LS374 IC 74LS245 IC 74LS253 UI, U2, U5, U9 Anew
314-0066 314-0067 314-0068 314-0078 314-0083 314-0085 314-0087 314-0093 314-0099 314-0105 oe Oe Carn
ja} | 37) 0 088 oa - as Eo SS SS 2
| i | Oor | S |
| S 2 EE 5 17 a 514 | 5 39 | 549 a |
‘ = 5 | a {= O 1 _
| = | = | Ei || L® | eos |
pag 2 13 —
| c= 74) tas) | sy | ET |
S
| = | — | = | a) | = |
= d 42 223 =
| 2) ee | a | ; (as |
=
| soca | oa] | 30 | fi | ||
| ; 3 | “em | , 16 | 220 S | |
| ae | S37 | 3 | i | |
| -Cae | 0 et | 24 | 533 —s | |
| = | a7 | as — 2 | fu | = |
| ® | 521 | p12 | (2) |
Isa. +) 27 . ge
CPU Board Assembly 800-0107
CPU Board Assembly—Continued
PARTS LIST DWG NO. 800-0107
Gremlin Qty Per Part # Assembly | Description Ref Des
315-0041 315-0046 315-0050 316-0764 390-0003 471-0101 471-0102 471-0103 471-0104 471-0122 471-0220 471-0221 471-0331 477-0002 481-0001 481-0006 482-0006 482-0010 482-0014 510-0052 510-0053 RREUN EE NWOWE EWEN Eee Re
213-0001 213-0002 213-0004 213-0005 510-0049 471-0472 280-0330 471-0473 BNE ENR RE IC Z80A IC 2114 IC 2516 (2716) IC PROM 32x8 LED RED RES 100 OHM % W 5% RES 1K OHM %W 5% RES 10K OHM %W 5% RES 100K OHM %W 5% RES 1.2 K OHM %W 5% RES 22 OHM &W 5% RES 220 OHM ’%W 5% RES 330 OHM ’%W 5% RES PACK 15x2.2K DIODE IN4002 DIODE IN914/IN4148 XSTR 2N 4403 XSTR PE 8050 XSTR 2N4401 SWITCH PIANO DIP. SW PUSHBUTTON SIDE PCM SKT 24 PIN DUAL INLN SKT 18 PIN DUAL INLN SKT 16 PIN DUAL INLN SKT 40 PIN DUAL INLN SWITCH 8 POS DIP RES 4.7K OHM %W 5% CARD EJECTOR RES 47K OHM %W 5% RIO, R11, RI5-R20 RPI-RP3
XU26 - XU29 XUI5 XU21, KU22 Sw2 R21
R9
space odyssey game electronics assembly
PARTS LIS DWG NO. 800-3161
- Gremlin | Qty Per Part # — Description 250-0475 420-0563 420-0607 800-0171 800-0173 800-0291 800-0185 800-3160 800-3163 800-3164 834-0051 834-0053 SCR PHIL RD #10 SHT MTL .5OLG BRACKET, CONNECTOR DECAL G-80 BRACKET DECAL SPACE ODYSSEY ELECTRONICS ASSY G-80 CAGE ASSY HARN VIDEO ASSY HARN SOUND ASSY HARN CPU ASSY VIDEO I BOARD SPACE ODYSSEY ASSY CPU BOARD SPACE ODYSSEY ASSY EPROM BOARD SPACE ODYSSEY ASSY SOUND BOARD SPACE ODYSSEY ASSY BACKGROUND GENERATOR BD
ow
| Lon | | | et | i | Mo | le Sf | pm ‘I |
| \ | i | ere | |® | c | ||
| ING | PKG | yi | [Ny | po | ||
| @, | | ca | iyo} |
Ws i i |
| | | = | gl |
| } | i | | |
| yc) | | | | i |
! i]
| msc | { | | |
! a :
| ls | | | | é | , |
| Hh | | | | | |
| IT Ny | | | i | 4 |
I Is | iF =; a ee ee
4 ©
z
prem WO fasten een
| “S. | [eels 75) | im | |
| WEI A3 | Ie | 2 | 22, |
oN a __S rere l2—~ F& “ws FE
(Evy a TS
eprom board assembly
PARTS LIST DWG NO. 800-0151 = Gremlin Qty Per Part # —_ Description Ref Des CAP CER .Oluf 16V AX | C2, 4,6, 8,9, 11,14, 16, 18, 21, 23, 25,27 CAP CER. .luf 16V AX | C1,3,5,7,10,12,13,15, 17, 19,20, 22,24, 26,28 151-0058
151-0060
170-0211 213-0001 314-0055 314-0058 314-0059 314-0104 314-0120 211-0008 150-0088 280-0330 an
N Reorenwe De PC BOARD SKT 24 PIN DUAL INLN | XU1-XU24 IC 74L8244 U25 IC 74LS08 U26-U28 IC 74LS10 IC 74LS138 IC 74LS154 CONN PIN TEST PT TPI-TP3 CAPE 10uf 25V C29 CARD EJECTOR
sa
EPROM Board Assembly 800-0151
video I board assembly
PARTS LIST DWG NO. 800-3160 Gremlin | Qty Per Part # Assembly | Description Ref Des
| 150-0088 | CAP E 10uf 25V | C80-C82 |
| 151-0005 | CAP CER 680pf 50V | c79 |
| 151-0008 | CAP CER .001uf 50V | C65 |
| 151-0011 | CAP CER .01uf 50V | C54, C64 |
151-0058 CAP CER .Oluf 16V AX | C57, 60, 63, 70, 71, 84, 86
| 151-0060 | CAP CER .luf 16V AX | C13-53, 56, 58, 59, |
62, 66-69, 72-78, 83, 85, 87, 88, 89. 151-0061 CAP CER 220pf 16V AX| C1-C9, C11, C12
| 152-0007 | CAP FILM .001 250V | C55, C61 |
170-0193 PC BOARD
| 211-0008 | CONN PIN TEST PT | TP1-TP3 |
| 230-0009 | XTAL 15.46848 | yl |
212-0099 CONN 15 PINM RTA
| 314-0001 | IC NE555 | U1, U10 |
| 314-0040 | IC 74LS 125 | U32, U50 |
| 314-0046 | IC 72804 | U60 |
| 314-0058 | IC 74LS08 | US, U44 |
| 314-0059 | IC 74LS10 | U41 |
| 314-0062 | IC 74LS74 | U6 |
| 314-0067 | IC 74LS30 | U59 |
| 314-0068 | IC 74LS32 | U48 |
| 314-0070 | IC 74LS86 | U3, U4, U39, U40 |
| 314-0073 | IC 74LS175 | U49, U54, U55 |
| 314-0076 | IC 74LS157 | U56, U57 |
| 314-0077 | IC 74LS166 | U33-U36 |
| 314-0085 | IC 74LS14 | U37, U47 |
| 314-0139 | IC 748163 | US3 |
| 314-0087 | IC 74LS139 | U15 |
| 315-0039 | IC 4015 | U16-U31 |
315-0042 IC CUSTOM CHIP 315-0065 IC 93419 314-0093 IC 74LS374 314-0138 IC 748283 314.0104 IC 74LS138 314-0123 IC 74LS257 314-0124 IC 74LS33 314-0125 IC 74LS38 316-0806 IC 32X8 PROM REV NEE EEE DEEN ANWEAR EE ENE NNE HE WHEN
“ee om ee
eee2@ ,020 4 iamea ie anni) cab sma |e
- ofa » 532 > 20 o 25 525 i 5 v - ic]
ra] = ic) | 227 | ep 24 236 223 (zz 54 ae Sar) 559 , 2 b 34 o24 ) 16 ' Ml a 224 0 226 e Brzal My so Ba a eo ET Lt
Video I Board Assembly 800-3160
Video I Board Assembly—Continued
PARTS LIST DWG NO. 800-3160
Gremlin Qty Per Part # Assembly | Description Ref Des
471-0102 471-0103 471-0122 471-0202 471-0222 471-0242 471-0330 471-0331 471-0472 471-0563 481-0006 482-0006 482-0014 213-0004
213-0005 213-0012 315-0067 477-0002 471-0221 280-0330 213-0003 314-0140 314-0053 151-0042 Ne =
RNR EN WRE NE RES 1K OHM 4W 5% RES 10K OHM ’%W 5% RES 1.2K OHM 4W 5% RES 2K OHM %W 5% RES 2.2K OHM 4W 5% RES 2.4K OHM 4W 5% RES 33 OHM %W 5% RES 330 OHM %W 5% RES. 4.7K OHM %W 5% RES 56K OHM 4W 5% DIODE 1N914/1N4148 XSTR 2N4403 XSTR 2N4401 SKT 16 PIN DUAL INLN
SKT 40 PIN DUAL INLN SKT 28 PIN DUAL INLN HEADER 28 PIN RES PACK 15X2.2K RES 220 OHM 4W 5% CARD EJECTOR SKT 14 PIN DUAL INLN IC 74874 IC 748175 CAP CER 470 pf 50V R4-R6, R15, RIG RT, R17 R10, R13 R14 R21-R23 R9, R12 R19, R20 R24-R31 R8, R11 R18 DI-D11-9 Q2 Zine xu, XU38, XU42, XU43, XUS2, XUS3 XU58 XU9, XU12 U12 RP1 RI-R3
XU45 U45 U42, U43 C90
BOOOODEEES PARTS LIST
Kem Gremlin Qty. Per Part # Assembly
COIDNARWNE 150-0088 151-0060 170-0227A 213-0014 314-0058 314-0059 314-0062 314-0067 314-0070 314-0136 314-0072 314-0075 314-0085 280-0354 VIC replacement board assembly
i DWG NO. 800-0212
CAP E 10uf 25V CAP CER .luf 16V AX cr. C5, C7-C11 PC BOARD SKT 40 PIN WIRE WRAP] XU17 IC 74LS08 Ul4 IC 74LS10 IC 74LS74 IC74LS30 IC 74LS86 IC 748151 IC 74LS174 IC 74LS393 IC 74LS14 PCB SUPPORT LOCKING
@ ~ez
ONES O8 hardware shifter assembly
PARTS LIST DWG NO. 800-0111
Item Gremlin Qty Per # Part # Assembly | Description Ref Des CAP CER .1 16V AX C1-C8 PC BOARD SKT 28 PIN WIREWRAP | XU9 IC 74LS08 U13 IC 74LS74 U1, U3, U14 IC 74LS32 IC 74LS151 IC 74LS175 IC 74LS14 IC 74LS161 IC 74LS395 IC 74LS299 151-0060 170-0216 213-0015 314-0058 314-0062 314-0068 314-0071 314-0075 314-0085 314-0097 314-0121 314-0122 COIDARWNE BNE EEE NWH HR OO
a “4
re PARTS LIST
Gremlin Part #
WOIDAMNAWNH 150-0088 150-0092 150-0095 150-0096 150-0097 151-0002 151-0007 151-0008 151-0011 151-0012 170-0202 151-0021 313-0001 313-0037 313-0015 313-0023 471-0011 471-0101 471-0102 471-0103 471-0122 471-0221 471-0222 471-0272 game power supply P.C. assembly
DWG NO. 800-0128
ty Per Assembly | Description Ref Des CAPE10uf 25V RDL —|C2, 3, 7, 10, 11, 14, 16, 19, 20 CAP E 100uf 25V RDL CAP E3300uf 16V RDL CAP E6800uf 16V RDL CAP E 4700uf 25V RDL CAP CER 100pf 50V CAP CER .005uf 100V CAP CER .001uf S0V CAP CER. .01luf 50V CAP CER .1luf SOV PC BOARD CAP CER 20pf 50V IC LM 723 DIP IC TLO81 IC LM 320T-12 IC LM 320T-5 RES 10 OHM %W5% RES 100 OHM %W 5% RES 1K OHM 4W 5% RES 10K OHM %W 5%
RES 47K OHM ”W 5% RES .1 OHM 5W 3% RES .2 OHM 3W 5% _—sJ R12, R14, R15 POT 1K CAR PCMTV ]R5, R23
BONeoo Game Power Supply P.C. Assembly—Continued
PARTS LIST DWG NO. 800-0128
Gremlin Qty Per Part # Assembly | Description Ref Des
481-0004 481-0006 482-0006 482-0014 482-0019 482-0100 514-0002 514-0003 514-0006 212-0004 212-0021 514-0055 471-0220 471-0223 471-0681 471-0104 DIODE MRS01 DIODE 1N914/1N4148 XSTR 2N4403 XSTR 2N4401 XSTR TIP120 XSTR TIP125 FUSE 3A NORM CLIP FUSE MTG. FUSE 1.5 ANORM CONN 4 PIN M CONN 10 PIN M FUSE 5A NORM RES 22 OHM %W 5% RES 22K OHM %W 5% RES 680 OHM %W 5% RES 100K OHM %W 5%
oe Qe
a5} as (35) ha : 2 2 Ia c Bio oe} [ss Pa 3| j oO © ©) m
ra} | a B a | TF
Fi
1 > Re} {ee} @ moe aD a
Cee, : cee c25 ee C27 aan 9 Be = = Rea} | 4 va}— Fi 4 BD j Fa cee cts ac ap
Game Power Supply P.C. Assembly 800-0128 @
linear power supply assembly
PARTS LIST DWG NO. 800-0146
| Item | Gremlin | Qty Per | |
| # | Part # | Assembly | Description |
211-0005 CONN CRIMP LOCK 211-0017 CONN QUICK %” 211-0042 CONN SOCKET AMP 211-0059 CONN PLUG 3 PIN AMP 212-0016 CONN FEM 10 PIN 250-0433 HEAT SINK PWR SPLY ISOL 250-0434 CHASSIS PWR SPLY ISOL 280-0005 CABLE TIE 280-0014 STAND OFF CLIPS 280-0117 TAB RIVET 560-0054 XFMR ISOL 800-0128 P.C. ASSY GM PWR SPLY RIVET POP 3/16 SCR MACH PN HD #4-40x% SCR SHT METAL #6x% WASHER FLAT #10 TRANSISTOR INSULATOR CONN PLUG 2 PIN AMP 2 COND ZIP CORD ELECTRIC CRIMP SLEEVE 211-0043 600-0079 280-0359 VMN ABRDOBRE EE DAH ERE IED
[8 p@ vem (4) as), passa ° BRN | bux sunt | tren) | wat wer [sue no 4.01
| ss | [ | < | e% Tall |
{RED __ a,
[RED . BRN
| [pen / veL | -. | BLK |
1224 Bod
-— ITEM 18
/ ITEM 4 m4
a tae GST ed ©
© 3Pk NS B© _— ITEM 5 : [J ™ : . @4 DD ‘Ile °
{10 16
7h aro Se DETAIL A \ |
tf : 6PL ‘N |
Linear Power Supply Assembly 800-6146
power supply assembly
PARTS LIST DWG NO. 800-0270
Gremlin Qty Per Part # Assembly Description
QUICK CONNECTOR 4” SPADE LUG 4” BRACKET SUPPORT SWITCHER MOUNTING BOARD SWITCHER WIRE BRAIDED 8.00 L. SWITCHING POWER SUPPLY LINEAR POWER SUPPLY WASHER FLAT #6 WASHER FLAT #10 SCR. PHIL. PAN HD. #6x.50 L. SHT. MTL. SCR. PHIL. PAN HD. #10x.75 L. SHT. MTL. SCR. PHIL. PAN HD. M 3x6 METRIC 211-0017 211-0076 250-0490 252-0124 600-0038 601-0158 800-0146
eee VESVeCADNABWNE BRPDRAD PEER YNND
AMOUNTING HOLES REF 4 PL HOO)
iT -T----T--a-
Gq
@ @ PARTS LIST
Gremlin Part #
312-0263 312-0262 312-0261 312-0260 312-0259 312-0258 312-0257 312-0256 312-0255 312-0254 314-0075 314-0119 314-0101 314-0055 314-0074 314-0072 314-0077 314-0076 314-0104 314-0040 312-0019 314-0070 314-0145 314-0062 314-0067 314-0066 312-0021 314-0010 312-0153 314-0059 314-0019 314-0078 314-0018 background generator assembly
DWG NO. 834-0027
EPROM 18 EPROM 17 EPROM 16 EPROM 15 EPROM 14 EPROM 13 EPROM 12 EPROM 11 EPROM 10 EPROM 9 SN74LS393 SN74LS377 SN74LS283 SN74LS244 SN74LS191 SN74LS174 SN74LS166 SN74LS157 SN74LS138 SN74LS125 SN74107 SN74LS86 SN74LS85 SN74LS74 SN74LS30 SN74LS27 SN7425 SN7410 SN7416 SN74LS10 SN74LS04 SN74LS02 SN74LS00 U34, U37-U39 U12, U24, U51-U54 U41-U42 U33, U36, U43-U46 U40 U16-U21, U27-U32 U35 U22, U65-U66 UST, U68 US9 U13-U15, U23 Ull U63 U62 USO U67 USS U47, US6 U48-U49 U25, U58 U64 U26
BEES sound board assembly
PARTS LIST DWG NO. 834-0041
| 313-0042 | AN6551 | IC1,5 |
| 313-0041 | MN3005 | IC2 |
| 313-0040 | MN3101 | ICc3 |
IC8, 7, 13, 15, 16, 17, 18, 21, 23, 24, 25, 26, 27, 29. IC9, 10, 11, 12 1C43,44 313-0034 LM324
312-0209 MB4391 314-0119 74LS377
I}: 37.00 (939) a p2 {O@) VOLUME = 7 non @® rary 2 37.00 839) & 3) conn = i 4) viewed 5| FROM SERVICE 6] WIRING END
+ vio 31.00 [787 Wo ¢ We ad RED 31.00 [787] 2|P7 BLK 31.00 [787]
RESET
WO ¢ NC YEL 31.00 [787] ORN 31.00 [787] P8&
Volume Control Block Wiring Diagram
Pl p2
BLK. 4.00 (1016) i | ] E eux.sooe7) -aTAT4 \ i I
AGHT
Buu. peor | @ BLK. 4.00[1016) Buk. 5.00 [27]
Bik. $00 [27]
Control Panel Wiring Diagram i I 8 way Le. : =[Dn_] JOYSTICK ! . i WHT uk
COUNTER TO SWITCHING PWR SUPPLY
BRI EMI FILTER BRN . BLK q INTERLOCK GRN Fa 2 ‘SWITCH tT 5 § + BLU BLU . BLK t \ ! I a =| hs 2 7 a |e
= z
x z\x Fy 5 Fd TO TRANSFORMER | BLK | { ] i
rt GND STUD
FUSE HOLDER
Junction Box Wiring Diagram
AC PLUG
BRN 2.00 [i] [aan 2.0018) _| | a
Coin Counter Wiring Diagram schematics
| 6 | 5 | 4 | 3 | 2 |
a SMOOTH SIDE u pe REVISIONS
| a | ee ESS] | DESCRIPTION | oa | |||
| LK | = | MONE | A | s | ||
| | | Y | a | 80070294 e ‘ASSY. MONITOR | == | 7 ee | ~ aa |
800 -O16S 800. i 5 rive,__ 20-0196 [7]
| -|-|= | ' | 6 |2 | 0 (515 | | |
| ae > rr, S | R 3] | Hala Pl | | |
J-BOx |
| i | GNO {4} | + s|s | | | |||
| 800 -0269 .| > gk | | | vIs | im 6/6 | p | ||
| I | alg} ext | | | usw X18 | ri al | ||
| | | rea | — | i |sis | ae | ||
| f | — | 9] 9 | ||||
| ruten_ || | 1610 | 2)2 | ||||
| — | BLK | Li | war. | |||
| = | Buk | mo | 33 | |||
| J | BURDEN | ap | Hale | P2 ja] we | ||
| z 4 | ale | | Hefi2z | = | |||
| |) a | WHT. | 3|5| Bux | 13113) | els | | | 7 G@nTRoll |
| 4 | TT |iahal | 616 | a | L | 800-0237 _~)ASSY CONTROL | |
| ii [ig | yuan 2002022 | — PANEL COMP, | ||||
| rw} | Wit WEL | j | TI | 800 - 3165 | — | |
| -- | ASSY. GAME | 2)27 pan | 4 | 22 | 1 | |
| ASSY. FLUOR. | ELECTRONICS | 313 | _ | I 13/3) eww | I | i |
| ib | BLK FF} Tenn} Lame | \ | SPACE ODYssey 4] 4 |_| AN | {|_| 4) q{| BED | LBL 9% | ' |
| Buk 7); | 800-0147! | 800 -3161 | |s] s+ Gav | im | oe | L__eove |
| \ | éfel || _wo | 2 | 2 Dawar | ||||
| __ | P3S)5! wT BL | 1 3| 9 |Mo. | FIRE dt | |||
| _- | Gs | | o~< | ||||
| Buc} S665 | 3 gui Wat BED | rr_18/é | — | 7 | ||
| BLK | i Fan | | ‘ol io | Buk. | Ui 2 4 BLK | 2 player | | |||
| ued | haf LL war ve. 179) | (Over | | | |||
| tali2)_|_|_GaN | Li} )3) (2/2 aN | 7 | \ | 4 | ||
| ' | B18 Tp | en 13| 3, O88 | | a po“ | ' | c |
D
| __ | | 14h ig) | VY 4 14) 14) | L_. | LEFT. }o“«¢ | |||
| assy rower supprytSt~S~S | \ | Lust s| i | | Is] | down | |||
| | | | 800-0270 | | | J | GND | a | |||
| pid | I | 800-0231 | |||||
| id | SWITCHING POWER a} BLK_4 | a | |||||
| SUPPLY REE | + | - | |||||
| | | | | | SEM fo | 31BLK | a | 800-0236 | ||
| | | a | Th | al | a | |||
| | | | | a | ps |2(2 | GAN | im | ||
| | | al | 5 1315 | RED | 1 ; Lj | le— | ||
| 4] 444 WaT | al | 4 | LN | ||||
| 7 | Oo | U | ‘ | ||||
| 00-0211 | | | 1 | 800-027 | &6 | | | “= | |
| | | | | ial | |||||
| | | i | = | |||||
| — | | | - | ! | 2j27 | assy coin] | im | |
| | | { | ad r | ()_oRN | P6 | orn | | i | |
| | | ; | t | f 2 T]-12 | 3) 3 }<f{-—_OBN_| COUNTER | | | | ||
| | | co | 19 i | + : I 2|+i2 | 4| 4} ORN_ g00 -0179 | | T | ||
| | | appa 818% | : | ° | ||||
| Buk | a | ie | BLK S| ono | Tho | - | | | |
| p | ‘st | BLK 6| 6p | P? |3}5[- pep | Nc | SERVICE | |||
| ok | e | 14 | [Two | 3/75 | 7 2 | i | c_2 SWITCH | = |
| LU | 3 | 13 | a | | BAN |g) 45 | 3 Auk | o— | 1 |
| 12| | gl +5 | NO | Ke | ||||
| a | | | fe | in | YEL — | I | [rey | |
| _ | uy | | 10] +5 | Ps. ale ORN, | = ad | |||
| 10} | ‘o—!) SWITCH | fs} | |||||
| LINEAR SQWER SUPPLY | H | Ne | ! | ||||
| 800 - 0144 | — | Tt | |||||
| 6 Fe | ; | Pg |3]s | ' assy. VOLUME CONTROL BLOCK | IO | |||
| AUDIO | IN 3 J | _— | ce | — | iS |
out AL)
| 1234 | aa | t | - | - |
L__| Roo | Bent | wenn wo. SR DESCRIPTION ES STS ER [TNO —
| - | DIMENSIONS ARE IN ACHES | Gremlin Industries, inc. |
| 800-0217 | FRACTIONS DECIMALS ANGLES. | ‘San Bioge, California 92923 |
| : | ————_ EFROTATS oat | A |
RTERT = PRAWN, FLoREs [5-27-61 HECREO earce [e28-0/ Top Assembly aan SE ODE TENT NO [ORAWING WO aa 100030
| en a [vaso | D | 700-0056 | A | |||||||
| , | 7 | : | 5 | ; | r I | APPLICATION, | 10_NOT SCALE DRAWING | Sone I | Par Tor 7 |
| 3 | 2 | 1 |
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
REVISIONS, : one | TR DESCRIPTION Dave | APPROVED io 20-27 037 40-47 50-57 60-67 70-77 100-107, a = iz ; 7 10-17 120-127 CI] SEE Sut 3 FOR CHANGES | 2-95: | [eo [20 dz je 20 [20 [zo jzo 20 leo 8 8 8 sy 8 8 3 8 8 ay 24. tev 7 7 7 7 7 7 7 7 7 7 AIS Al é 6 6 é | 6 iG 6 6 6 Al 5 5 5 5 B 5 5 5| 5 5 200-207 4 4 4 + 4 4 4 4 4 4 9 gig Ul-ves E107eIZ, 3 ul 3 u2 3] 3 3] U4 3] ous 3} us 3] our 3] ue 3] us 3} ulo 220-227 2] 2716 2] 276 2] ate 2] 2716 2) 276 2) erie 2] e7i6 2] e716 2) ans 2] ene f 230-25 t i i t o t i i fi nl 12 240-247 23 23] 23 23} 23] 23] 23] 23 23 250-257 22 22 22 22] 2 22 2 22 22 260-267 Ee) spo Nssatepa? = apopay aed SPO | SPAPSPeT7 apap baud SPO pspayispayi7 loo" Pa: pop sfasficfiz§— Ya folihspehshiefi7 ofiop iaalisyicli7 270-277 rT tt t HS tC 4 — # + 4 + + 2 t t nape -¢ + 4 + i + + + + + + + } HT inne ” t 4 + + . + + tr O14 + + + + 4 + + + VALS 130-137 160-157 160-167 170-177 200-207 210-217 220-227 230-237 240-247
- 20 20 20 20 0 20 20 20 20 aH , ee ee ee eee 7 7 T 7 7 7 7 7 7 pidtsea 6 6 8 6 6 6 6 6 6 fost 5 il 5 5 5 5 3 5 5 4 zy 4 + + + + 4 + uit 3 ule 3] ls 3] ue 3 us 3} ule 3 uit 3] uss 3] ug 3] uz0 3 8 2716 2 276 2 2716 z@ 276 2 2716 2] are 2 2716 2] 276 2] 276 2 2716 as 2 7 7 7 i 1 1 t i i . 23 23 23 23 23 23 23 Fall 23 4 [4508 22 22 22 22, 22 22 22 22 22 aT apofi sasha — ]apiofiif pop fispspsfie]i7 Spo spasieyi7 §— /afiop pspahispeli7 TL: apo af LGU Lio bRaisfiei7 §— Yafioliifisfiafispeyi7 §— Yafioliifisfayispeyi7 ——, al 4 130-137 ' ius | | t | +4 0-7 s®> r++ u on Pont TOT 48 aan a t t t + AIG AW AIZAIT — 1g TALSO€ t t t tT 170-177 ae 13 u26t + t t tt + , LY + ie + 9 741508 I es fu + + + + + + +— + + ATSB 1-7 ? Peon delsbelir a Laholufstalshsi7 4 Jokobbshshsheli7 Lh 7 1 7 — 1s@—> as é 6 é 5 S 5 Is fit 4 4 4 a BUFFER F ves aie——> Alz 3 ut 3 uee 3 u23 7418244 7 2] e716 2] eve 2] a7e s 9 fi fis [3 |r fie fo Ania 1 t 1 23 23 2
ra o> Te Tea DB 01 D2 D3 D4 DS 06 D7 127d 50-257 260-267 210-217
A > (415) qo| Bent | weriheVin no. Oe SESERHON rr ez CIES: | GSCI C Ie IMENsiONS age IN incHES Gremiin Industries, Inc. aac = 0 5 I5,CI7,C19, C21,C2S, TOLERANCES A: on Gsittoraia ois artsy? mais 8 ; Naf TF C20,C22.C24, 7 C25,CeT. FRAeTIONS —DECANS — ANOLES ROS aE oe ve )2—> (10, 7 —4 ‘BUFFER €26¢26, = = # Ang >a (a0) Ls aia) as a7 4 sha BUFFER Otuf Olaf wet PRAWN Fotki 10/478
- af . on i eS ERR Fog Tyrone EPROM Board ‘ 4 27 74Lsi0 SE $ L__s (mem) _ SHE [CODE WENT NO ]ORAWING NO. REV. D 800-0151 cf NEXT ASSY [APPLICATION DO NOT SCALE DRAWING scale NONE [Seer 4 OF 4 8 7 | 6 ! 5 t 4 3 c
BOO0-O1S\
| 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 |
REVISIONS
| [Zone Tore | DESCRIPTION | Dare | APpRovED |
| [ | ‘A | RELEASED | 3 [s-arA | AC |
D
1 u38 gl ~ _s INSULATION THIS LEAD ONLY —— 10 | v3? vss c
FAOM TO EDGE
| _— | AN | Device | CONNECTOR |
| - | ] | DESIGNATION | DESIGNATION |
i [Al o} | a2 i a3 \e— us7 | | DESIGNATION
| | | R27 | R23 | NEER | FAR | pn i] ai | |||||||
| ' | - | —- | — | + | — | SIDE | SIDE | PIN Z| 39 | ||||
| 7 | a | 3 | PINS | 37 | |||||||||
| L | [| __uis | U36 | u4e | use | 1 ZL | 32 | Pine | 3S | ||||
| 7S | opr | m_| 33 | Ping] 33 | ||||||||
| > | 4 | p | m | 34 | | Pin i2| 32 | |||||||
| a | ml | y | . | a | |||||||
| ~~ | i | rnd | “< | P| 38 | PIN IS) 34 | B | |||||
| | | ~s | y2uss 7 | | mice | i a | 36 | PIN 6] 36 | 1 | ||||
| ~ | ws | B60]! | || (47737 | Pin '9| 38 | < | ||||||
| 1 | = | ~ | \ | J} Le | 38 | Pin 2 | ™m | ||||||
| sal | an |! | | | |||||||||
| “us | wu | via | use | uaa | = | \ ||| 2 | Ts | pin? | £ | 8 | ||
| | | — | es | 8 | rT | 4 | Pin ol PD | < | |||||
| | | 5 | PNIO/ Pt | |||||||||
| i | w fa! | pin is| 7 | ™ | ||||||||
| —- | ee ——————— a | + | |||||||||
| | | \ | = | ]) wT ae | PIN 3 [UEO PIN B | fo} | ||||||
| ct | Fe fi | f | U33 | vas | | | _us3 | ce | x | 7 14% | PIN 4) 40 | 8 |
oa) —>—______. UB |
| om | reap | | | ; | — | _ |
| [~ | \ | | | 3[1 | 800-O11| [HARDWARE SHIFTER ASSY |__| | |
| alls | Lu | i | 2[1 | VIDEO | BOARD | — |
| Lt | (o) | ‘ | ti2 | 280-0354 | PCB SUPPORT 5 LOCKING | |
| a | 2d | i | ITEM] Roo | Geek IDENTIFSING NO. | Of DESCRIETION | VENDER |
PARTS LIST
| — | UNLESS OTRERNTE SPECIES | [CONTRAST NO |
MENSIONE ant TN INCHES ROLE MANS AR: Frictions ogcmars —ancies |__
| * | 2 | ‘APPROVALS | DATE | A |
| Hl | es | DRAW | i | |
| ATTACH JUMRER WIRES TO FC _BCARD BOTH SIDES USING | ! | TEAL | pen" FLORES (510-81 | Video I Board |
| LOCTITE “SUPER BONDER OA EQUAL. | - | GGECE FENG) | Modifications |
- JUMPER WIRE TO BE 30 GA. INSULATED
| 2. SOLDER DEVICE C90 BETWEEN DEVICES U 37 AND U 38 AS SHOWN. | ia | D eee DENT mo [onan 00 3160 | REV. |
100030 -
| A\ADD JUMPER WIRES AS PER CHART, | NOT ASST | USED ON | s | A |
| NOTES: | ‘APPLICATION | DO_NOT SCALE DRAWING | [SCALE NONE, | seer 5 of 7 | |
_}—_ re a
| 3 | 7 | 6 | 5 | f | 4 | 3 | 2 | 1 | 60 |
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
REVISIONS
| Zone [UR | DESCRIPTION | DATE | aPPnOvED |
A] RELEASED we |e 48r ee +
+
7S 1s Li 3
Ie hal wal oo |S 12] 73..378[@
wan} ii Diba
| par [24 | J | = | + |
mywr 23 _ +5
| = | mem & [2 | +s | 7aLss2, | 1 yo\7 |2 | ||
| +) RST | 276 our aL | 1 L4_ogeHet ela | ott | is | LD iy LE | |
| ag | ew 28. | >| ve | Use | uz [5 | bh | [4 |
| #—____] | 740 | 74LSIT. 2 | 3 | |||
| c | 7 48516) | aausaa, | 5 |e | Bho, |S | c | |
| | | s 6 | ul | 3[6 | 12] 7418295 |@ | ||
| 2 | Osta | Ge |
Ci p+ Listas
| * | = | cops | — | our |
| z | UR G2 G00 | an |
a]? 2 r
ui A 1S 3 [+—
| 7 | : | Tasia | 74cole |
(ur: 141808 |UI3} zarsaz{ua) Ic
| | | T | + |
i2 Viz
| B | 13 | ns | 4 | f | u | |||
| 7 | i | 19) 5, | 2 | |||||
| 3)741502 (v2) | al - | 2 | 3 | a | ||||
| 4 | ie | > | 7 lg | 3 | a5 74432 alg | SI our | Z | 6 |
| W4Lba0R | oo | 2 wie | t | |||||
| . | Loz) yuryyer | r— | us | 4 u7 | = | |||
| rs | 1 | 10 e | . | 74usisi tt | 743299 | |||
| 74154] 7acsia |7aicia 1S | +5 | STs | is, | i | a | |||
| Le | = | . | . | t | aNnD |
+
| 7 | "0 | le | bs | ||
| zr gle | 2h $b | ze al =f a) | fe | ||
| zere7a] ui | arora] U4 | v4] | v2 | racara] U3 | FE |
| 2b =e | ub 5 | ab glet ab sk | ul cle | | | |
| a | o> 3 | . | |||
| q | SJ | ‘4U8T4 | 5 | aml | |
| id | T | 7 | iz 74 | 3 | v |
| : | eooe | PART oF | NoweNCLATURE |
do] Bet | oem no. On DESCRIPTION PARTS UST UNLESS OTFINISE SPECIFIED [CONTRACT No. DIMENSIONS ARE IN INCHES TOLERANCES ARE: FRACTIONS DECIMALS ANGLES = xe 2K: Gremlin Industries, Inc. ‘San Diege, California 92123
MATERIAL Hardware Shifter
“SHE [CODE TBENT NO: DRAWING WO. 800-0111
‘DO_NOT SCALE_DRAWING.
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
REVISIONS
| 5 | col | Ree | cag | ‘ZONE | LTR | DESCRIPTION | pee. |
V & 254
| cot | cooor | ox | 2M Sov | Tr recess | [625-81 | |
| rm | C21 | . | I | |||
| ro | tk | os | ns | re | =e | chat |
| ol | 2 | “| | > | sy | 1 In 057, aS | po uaceou | |
| pe | a | R39 | re27 | 2.2K 5.6K | (saz) | |
| 123/ | MA ISO | sik | Re? LB | ya | 50V | D |
| miso +L c70 | i | ive | 2) * | |||
| Son pare | ve | ise | 7 | |||
| } | i | Waiso R107; 10K | OK waso [iw | tse | ||
| m | 7 VFR | Rws | “Ler | cs | |||
| case 22K | ae | J |
2 OO 3 av
| Re | nl | WaisoMAISD | |
| rez | ‘ | sn | ce,1000P |
| yt | : | 2|wnsior [6 _ R5, 16K | = |
3 8B, 5.6K 2 Rooks A 5 4
| E | ds,aun| ook oe Sie | o | a A | |
| mm laa | 3.36 | ov | = | BBD out |
| fox Sure | Zor 2200" 330° | age [eater sie (sn2) | ||
| i | a oh mh | we | ||
| sev 70 THELESS | “nv | c | ||
| =— | ft | 2 |
R23 5.6K
| ural | new | BoMuS UP SOND |
OR fae 7K (sH2) \oo0P i ces Film pales “1m av rele wlan
| tow 3 | : | rc | Rvs. | |||
| Mao tm | 8133 | Ki3e | sue | cs7 | ig | A |
| > | 226 | R43 | 42 | |||
| sik 3. 5K | a s | an | B | |||
| . | = | a2K | 3.3K | SHI | ||
| ; | . | , | a | soy | us | |
| ACCELERATE | Re | 3.3K | /— | |||
| 4 | 458 | = | ||||
| (sH4) | Tea! | wn |
1 oa Risa v0 n139,, 10K aTacR woe >" | Tos (sua) was ASM 1K 8 card 1: BAS. & (sw) a
NOTES : ZX wwe oF RESISTOR CAN BE CHANGED FOR ADJUSTMENT. DIMENSIONS. ARE-IN INCHES TOLERANCES ARE: FRACTIONS DECIMALS = ae xs TONCESS OTHERWISE SPECIFIED
| coee | PART OF | NOMENCLATURE | Tew |
| go | BeRt_| sentra no. | Oe DESERPTION | NO. |
PARTS UST
anes = APPROVALS
PRATERAL
im
NEXT ASSY USED ON |B so DONE lomo ee | = ezeoy MECH ELEC Sound Board
ee [PROJECT ‘CODE IDENT RO [DRAWING RO. 834-0051
DO_NOT SCALE DRAWING
3 2 1 REVISIONS ore [rR SESPTION OnE Al RELEASED ce [6-25-61
5v
R247 ic i2 22K C17 RIT 3 RI20 " 39% - = MAIO RI53 ev
| 124g | 5IK | 100K | ae |
| ol 470. | RIG | R122 | | ese |
10K 680,
| MAISO | ar | > BDD IN (SH!) |
RG2 10K
| oy | Icio | C35 |
R252 439) 7 yrs 7A | R20 snot sounp our tS 4 ko | esv ORAN
| R296 | q | BBD an| |
1K 0,
| 4 R25] | 1 680p | (SH) | D-BOMB SOUND |
snot
| c| | Bon Oa | BONUS UP SOUND >—@ |
2.2m (SH3) APPEARANCE UFO SOUND >—@
5v 5Y A cps R236 IM 470K
| tpIC27 cp ty ep | 2/2 | is £32 | RI6 | $. EXP. SOUND | ||||
| 36K | 25v | R23: | R20 | PN 3 | IN | our He | + | |
| R238 | 7| | @ | 3 | 2006 | Bem T Onl | 2.2K | 10K |
| 1k | 410g RE Ce] | !K | 470K3 | Slo | 35v| 25v | con Ro | Sod | |
| SuRRy. | bteda 123, a sag MA's0 R199 —? | 2 | "I ces | ||||
| (SH) | ct | biz | IK | yer |
{ RSS? R53 ics
| ey | c3) | 439) | C34 A | {1} 6nd | |||
| B | 1C 27 | 100K V2, 50K | R57 | filis | Ye | | sn) | RIS. EXP, SOUND | a |
| ; | 1 | Ww | out! | F4¢ | z | ||
| R209 | te 33K | i | , | 3.3K | |||
| RS! | 224 | cn Ro | 47M | R36 | ||||
| IK | 50V | 25V | VOR | ep. | |||
| TONG. | EE | Rse | 6] | fl | ya Ni | ||
| poi | c26 | ae | 35 | c2I | |||
| a4) | [047 | e60p | SOUND OUT | ||||
| 2.2 | SOV | a |
+ SOUND OUT
7 fue
a
| | ee | Pay OR | NOWENSUATURE |
00 | eR | went no. Oe OESEPTON PARTS LIST FoaLese. SINERWSE SPEDIIEO [CONTRACT Wo hiensions ane IN ness TOLERANCES ARE: A FRACTIONS DECIMALS ANGLES
| : | ae | APPROVALS | OTE |
x ATER PWNcaTTELL |6/22/61| CRORE pee lee 5/ Sound Board MECH ets. SHE] CODE DENT WO[BRAWING RO. Rev i no
| ROT AY | USED ON | PRORECT | D | 834-0051 | A |
| OT | APLICATION | DO_ ROT SCALE ORAWING | REA None |
- REVISIONS atl DESCRIPTION ‘a [RELEASED
BBO IN (SHT.10F 4)
“Batme Pt STAR
- (sut.aor a) Lb aon C27 — us asv In 30% wv Riso
six 2 R83 Bier4-) ev. Py
| six $ | fisn | low |
| rise? | fRN9 siK | Rise |
c ST RIBS aise 10K c case TR9
a
Arsen wz IC29 R2Ie 2 sov ne 6.0334 sex
ces Ree
Da | 2 ICle I+ —_ sv Iclé 33K
| iy | RICO sy y | ICII | 22K S APPEARANCE UFO SOUND (SHT. 20F 4) | ||||
| ak | sov | sov | [Axe | ||||
| 47% | ae | n | |||||
| elt | oF RIOT | 224 | “92 | | eeu | gig | |||
| sea el | MAIO, | if | iN | our| | tt | S880 IN (SHT.10F 4) | B |
| mo | case | at | z | RS | |||
| bw | aa | . | Tre | a | con po] | 47 | ZN |
| APPERENCE | fread le | “ah, | Res | ] 0 |
UFO ie Rios (sun aore>——} 1c3) ca hia can
| 7 | ev | T |
| 1c35 | a | 0 |
fe} fo}
+ a ©
NOWENGUATURE oy e
TGnLESS OTHERWISE SPECIFIED DIMENSIONS ARE. IN INCHES TOLERANCES AE:
ox = [CONTRACT NO PARTS LIST.
Ser es, Cnr 9125, JFRACTIONS DECIMALS ANGLES =m ee
MATERIAL ‘APPROVALS PRAWN J ORES [ORECRED GRICE
EC
NSH
NEXT ASSY USED ON Sound Board
oe [CODE TENT 190: BRAWING NO, 834-0051 A APPLICATION. 'DO_NOT SCALE DRAWING sneer 3 oF 4
8 7 6
287 (> pec di Ic42 pes (> ——__ LS04 ve7 of, 1044, ,|9 eit 7 P82
| pat (> | pee 7,5 | alt nts | S |
DBS 4 2D 2a i
| p33 O>- | pea 3|, | 1ql2_BiT4 |
s377 7
| ve2 @™ | DB3 13 5D | 5 j2 BIT3 |
DB2 14)., 6Q 15 BIT2
| ap | 8a | > |
DBO <> cxa &
output @
AG
Al az @y—41c
1043
| DB7 3 ID | 1a 2. BIT7Z | > |
| DBE Had | 2Q 5S BITE | > |
; pes 7|.5 3q/& BITS
| as ®—_ | “4 | B+ 8 > gant BIT 4 | > |
| a4 | DB3 18) gp | aal® BITS | |
| asQ | pez 17/5 | ale BIT 2 | >. |
DBI /4) 6p 6a iS BIT I
| Ae | DBS 13 SD | 5a 12 BIT D | > |
9 8 ckl & aa > Te 30 ") LS0F 2
sv 4
8 7 6
| 4 | 3 | 2 | 1 |
REVISIONS
| = om | DESCRIPTION | tare | ApoE |
A RELEASED CTC |6-25-BI
D
BLACK HOLE (SH 1)
KFPEARANCE UFO (SH 3)
WARP (112)
BSNUS uP (GH!) SHOT (GH 2)
GND <I GND
TONGEKP. (SH 2) o— D.BOMB (SH |) BATTLE STAR (SH 3) ACCELERATE (SH !) DC.12V T 12Vv a +| SHORT EXP. (SH 2) R227 aoe
| BACK G. (SH!) | 1004 = 100m | Rees | 220u |
| 16 | 16V | I 16 | B |
tc DC, 5V @ > 5V 3
| ‘ | ® | + | +] cP | cs} |
470p = 0-1ys 9 i 1
| i | & | Jeav [ee | 1 |
® 3 ©
| | sabe | Pant OR | NOMENCLATURE | Tew |
| B00 | AGERE | wenn no. | Oe ESERIETON | 7 |
PARTS LIST FONLESS OTRERATEE SPEOFIED [CONTRACT Wo. t |DIMENSIONS AKE IN INCHES: FotenAwees Ae FRACTIONS DECIMALS ANGLES
| : | xe | APPROVALS | DATE | A |
ES ORAWN [MATERIAL CATTELL 16/28! RRO Gece |e-zr-8/ Sound Board MECH
| nee | ELEC | THEE BODE TOENT WO[ DRAWING NO: | Rev |
tad D Tara | a 3 834-0051 | A
| APPLICATION | 1DO_NOT SCALE DRAWING | EAE WONE | eer For | |
| i | 4 | 3 | 2 | 1 |
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
| 8 | 7 | | | 6 | 5 | t | 4 | 3 | 2 | 1 |
ESS
| TONE [oe | DESCRIPTION | [ane —[arenoven |
A | RELEASED Tefiva_ [723 Pa
| + | wae. | @> +5 |
oN
| mesor (4) | ow | x | |
| DE | DS | © | D |
os oF _ J+ C26
| 2sovac OF | 136 svc) | if | al | 100 UF |
| 12, | ) 10 | TK ay g/d 8 | 100 | pay |
| svac OF | ‘sowewanrrent2 ¥ | 2 | ||
| 100 VAC | thy ovac | | | RS |
| Nie ovac u
c RI
| Ra | LOSUF A 4.7K | ' |
Q
+ > GND b %
| C24 | + C2 | er CS | |
| d+ 5300 uF | = OF | 10 UF | c |
| sald | 25v | Vv |
v “nv ut sv
| Gea | 4 \> | S | D -5 |
Caen
as . arisies meso (4) Las be BY 3 3023
| AS | + | BD +12 |
os ¥"b1
cis
| R3I | ao Bcee | \ | 150 UF |
| 27K | 7 4700 ur | 25v |
25v
| aubio IN | Siw | 8 |
i rem Ov ekg} Rz6
| Py) | oe | 10 | < | |
| iN6231 | : | — | ||
| + | + | leis, | cz0 | ci9 | a |
| g | SIOUF > .05UF | por | S |
an 7 5
| [ozs | d | wy | ete nree —— | joe! T1120 | g |
| 25V | 1a7 | Hy |
1 j 3A
| 1 Ass | ® =12 | ig | Le! | ay |
Iok ire L-—SeSe | AUDIO AMPLIFIER
| =Vee | i | [3 Ai39.2 3w | ||
| co | ry IDE | ‘PART OR | “NOMENCLATURE | | |
| ® a.c. | I | ao] Be | weitneno | eer | im |
25 PARTS ust
| $ | Lene po | Gremlin Industries, Ine. |
| racTons DECIMALS ANces | San Blogs, Caufornés 92713 | A |
: Bes * opin vag 7-7 90
| [MATERIAL | Jere | hake 4 |
Zinn.a use| Game Power Supply i, ALL RESISTANCE VALUES ARE IN OHMS, 1/2'W, 257,
| NOTES: UNLESS OTHERWISE INDICATED | 7 | “Size [CODE WENT NO TORAWING RO, | REV | ||||
| Lo | D | 800-0128 | [4 | ||||
| APPLICATION | DO NOT SCALE ORAWING: | some Nowe | | [meet oF | ||||
| 8 | 7 | 6 | 5 | 3 | 2 | ] | 1 |
YOUR COMMENTS, PLEASE!
Your comments will assist us in improving the usefulness of our publications. They are an important part of preparing for revisions of manuals and parts catalogs.
If you have any technical questions about any SEGA/GREMLIN game, are requesting additional publications, or have a suggestion about how we can make our manuals more useful to you, drop us a line or use the handy form below. We value your input.
Comments:
Fill in if you wish a reply: Name___ SFr, E Address
City State Zip Distributor
Operator
Other. so
First Fold
BUSINESS REPLY MAIL
No Postage Stamp Necessary If Mailed In The United States
POSTAGE WILL BY PAID BY:
SEGA/Gremlin 8401 Aero Drive San Diego, CA. 92123 Attn: Customer Service FIRST CLASS PERMIT NO. 10129 San Diego, California
Second Fold
a6pq sul adey
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.