CATHODE RAY TOMES

Street Fighter Alpha 3

Street Fighter Alpha 3 (Europe 980904) (Capcom, 1998) · Manual · 16 pages · 28 sections · original scan

Page 1

©CAPCOM CO. LTD. 1998 ALL RIGHTS RESERVED. ©CAPCOM U.S.A., INC. 1998 ALL RIGHTS RESERVED.

OPERATORS MANUAL

WARNING

This game is for use in the United States of America and Canada. Sales, export or operation outside of these countries may be constructed as copyright and trademark infringements and is strictly prohibited. Violators are subject to severe penalties and will be prosecuted to the full extent of the law. TSFA1300 062298

Page 2

® CAP@ON coin-op, inc. STREET FIGHTER ALPHA3 ™

THANK YOU FOR PURCHASING STREET FIGHTER ALPHA3 ™ WE INVITE YOU TO USE THE FOLLOWING MAILING ADDRESS, TELEPHONE OR FAX NUMBER FOR PARTS OR SERVICE INFORMATION CONCERNING THIS GAME:

CAPCOM® COIN-OP, INC. ATTN: CUSTOMER SERVICE 475 OAKMEAD PARKWAY SUNNYVALE, CA 94086 PHONE: (408) 522-5333 FAX: (408) 522-5331

THE SERIAL NUMBERS OF YOUR KIT ARE LOCATED ON THE GAME CARTRIDGES AS SHOWN BELOW. PLEASE HAVE THESE SERIAL NUMBERS AVAILABLE WHEN CONTACTING US FOR SERVICE INFORMATION.

AAMA "B" CARTRIDGE SERIAL NUMBER SERIAL NUMBER

"A" CARTRIDGE SERIAL NUMBER (BOTTOM OF CASE) ‘300900

DEPENDING ON THE TYPE OF KIT YOU PURCHASED, PLEASE RECORD THE SERIAL NUMBERS HERE:

“FULL” KIT A-CARTRIDGE SERIAL # B-CARTRIDGE SERIAL # AAMA_ SERIAL #

“B” KIT B-CARTRIDGE SERIAL # AAMA_ SERIAL #

Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC.

Page 3

® CAPCOM" coin-op, inc. STREET FIGHTER ALPHA3 ™

TABLE OF CONTENTS

Warranty Information rssesnsssssssuusssssssssssuusssnsssssvssnsssnenensnnnssescensnnnnnnees ii

Kit Inspection sesessuuuasnnnsssnssusansssssnssunsnnseesnesnansseenennansnseeeeeeneeea 1

Caution acannstestnunuansnnssesuusinsnssssunssanessnnuuasaseensnnnaneneeeee 2

“FULL” Kit , “B” Kit Preparation Installation Control Panel Overlay Cabinet Graphics Re-assembly of Components Remote Volume/Test Switch Control Panel Wiring Game Cartridges oa, RR wo Rw

Test Mode Test Menu Accessing the Menu How to Select an Item Closing the Menu Menu Item Descriptions wens! Configuration Menu System Configuration Game Configuration WOWDAMDAMVHAAH

Wiring References Table 1: JAMMA Connections se Table 2: Auxiliary Cable Connections ...

Reference Information (—(— ———————vasssssssssessescsessesesesceseseeseseseeseseseeeeeesesenes Game Case Controls and Connectors Typical Control Panel Layout

Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC. 1

Page 4

® CAPO coin-op, inc. STREET FIGHTER ALPHA3 ™

LIMITED PRODUCT WARRANTY (APPLIES TO DOMESTIC SALES ONLY)

CAPCOM® COIN-OP, INC. (Seller), warrants only to the initial purchaser of its products, that the items listed below are free from defects in material and workmanship under normal use and service for the warranty periods specified:

A. CPSII System Cartridges One (1) Year B. Electronic and Mechanical Components: (90) days

No other part of Seller's products are warranted.

Warranty periods are effective from the initial date of shipment from seller to its authorized distributors.

Seller's sole liability shall be, at its option, to repair or replace products which are returned to Seller during the warranty periods specified, provided:

A. Seller is notified promptly upon discovery by buyer that stated products are defective;

B. Such products are properly packaged and then returned, prepaid to Seller's designated plant.

This warranty does not apply to any parts damaged during shipment or handling, or due to improper

installation or usage, or alteration. In no event shall Seller be liable for any anticipated profits, loss of profits, loss of use, incidental or consequential damages or any other losses incurred by the customer in connection with the purchase of a CAPCOM® COIN-OP, INC. product.

WARRANTY DISCLAIMER

EXCEPT AS SPECIFICALLY PROVIDED IN A WRITTEN CONTRACT BETWEEN SELLER AND PURCHASER, THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

IMPORTANT NOTICE

THIS SHIPMENT HAS BEEN CAREFULLY INSPECTED AND PROPERLY PACKAGED BEFORE LEAVING THE FACTORY. WE CANNOT ASSUME RESPONSIBILITY FOR BREAKAGE THAT MAY OCCUR DURING TRANSPORTATION OF THE GAME. IF THIS GAME IS DAMAGED UPON RECEIPT FROM THE CARRIER, IMMEDIATELY NOTIFY THE CARRIER AND FILE A DAMAGE REPORT.

ii Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC.

Page 5

® CAPCOM coin-op, inc. STREET FIGHTER ALPHA3 ™ KIT INSPECTION

There are two kits available for conversion to STREET FIGHTER ALPHA3 ™:

  • TSFA1000 (“FULL?’ kit) contains the complete game cartridges, all necessary graphics, and replacement joysticks and button switches. The “FULL?” kit is intended for conversion of most

JAMMA-compatible, horizontal screen cabinets.

  • TSFA 1000B (“B” kit) contains the game software cartridge (B-cartridge) and must also be installed to a current CAPCOM® System II game. It includes all the necessary game graphics for a cabinet conversion (marquee, control panel overlay, monitor card, etc.).

Check that all parts have been shipped with your kit. If any parts are missing, contact your distributor immediately.

TSFA1000 TSFA1000B

KIT PARTS LIST

PART NO. TSFA1400 DESCRIPTION CPS II System Cartridges (A/B ) TSFA1400B

CPS II System Cartridge (B)

GE1200 Monitor Card ‘[TSFA1110

Marquee Overlay, Control Panel

AW00216

AW00245-2 Decal, Joystick & Button Switches TSFA2520-01 Decal- Top, Instruction ‘| TSFA2520-02 Decal - Bottom., Instruction PM00206

Manual, Operators

v v Vv V Vv V Vv T v AW00147 Decal, Cabinet Side _[GE2030 ‘| Joystick, 8-way 16-0130 Switch, 1-Player Start Button (White) 16-0131

‘[ Switch, 2-Player Start Button (White)

16-00133 Switch, Button (Red) 16-00134 Switch, Button (Blue) 16-00136 Switch, Button (Green) 03-0052 Cable, Auxiliary Volume/Test 2a) al aja) ea) e) ele) ej elelele) els

13-0066 Bracket, A-Cartridge Mounting

Note: Because of availability, your kit may contain different color of push-buttons.

Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC. a]

Page 6

@ CAPCOM" co-op, inc. STREET FIGHTER ALPHA3 ™

CAUTION

Please read the following instructions to keep the PC board in good condition:

@Do not block the ventilation slots.

@Do not drop or bump the board.

@Do not spill any liquids on the case.

#Do not disassemble the case.

ATTENTION

@ The product that you have purchased contains a recyclable

battery. At the end of its useful life, under various state and local

o laws, it may be illegal to dispose of this battery into the municipal

@ —/ waste system. Check with your local solid waste official for details in your area for recycling options or proper disposal.

DISASSEMBLING THE CASE OR REMOVING THE STICKER MAY CAUSE THE TERMINATION OF YOUR REPAIR WARRANTY

OF YOUR REPAIR WARRANTY.

2 _ Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC.

Page 7

CAP@OM’ co-op, INC.

KIT INSTALLATION

WARNING:

MAKE SURE ELECTRICAL POWER TO THE GAME ISOFF BEFORE STARTING THE KIT INSTALLATION.

PREPARATION

  • Disconnect and remove the old printed circuit board(s) from the cabinet.
  • Remove or open the control panel, and disconnect and remove the buttons and joystick(s) from the control panel.
  • Remove any covering from the control panel overlay, and then remove the control panel overlay.
  • Place the drill hole template over the control panel to determine where any new holes should go. Center punch any needed new holes on the control panel.
  • Cut out the new holes using a 1-3/16" hole saw.
  • If there is an additional control panel cover, figure 1 (such as plastic or lexan) that will be utilized, cut any additional holes using the same template. *cover is not included in the kit.
  • Plug up unused holes with a wood dowel any rough edges. (1-1/8" diameter) and sand

INSTALLATION

Marquee Installation

  • Remove the marquee plexi glass, marquee overlay, and the cabinet graphics.
  • Install the new marquee and replace the plexi glass. Clear plexi glass is included in “full” kit.

Control Panel Overlay Installation (See Figure 1)

  • The control panel overlay in the kit is oversized to accommodate most control panel sizes. Center the overlay on the control panel, leaving some excess material at the edges.
  • Remove the protective backing from the overlay and press it down on the control panel, keeping it properly aligned. Press it down firmly, smooth out any bubbles, and press it over the edges.
  • Trim any excess from the overlay. Place the drill hole template on top of the overlay, aligning it with the joystick holes. Pierce through the overlay at each control panel hole. Then, cut away overlay material covering the joystick and button holes. Remove the template and clean off the overlay. STREET FIGHTER ALPHA3 ™
  • Peel off the backings of the 6-button and joystick decals, align over the control panel holes, and press in place on the overlay (refer to the drill hole template for proper placement). Using a knife, trim material from the center hole of the joystick decal.

14. Install the control panel cover, figure.1. (if required).

Overlay (Trim to size)

Figure 1: Overlay Installation

CABINET DECAL INSTALLATION

19, Remove monitor glass and install monitor card

  • Peel-off the backing to the instruction decals and place on both the top and bottom of the monitor card. (See Figure 5). Also, apply the cabinet decals to both sides of the cabinet.

MARQUEE OVERLAY MONITOR

CARD CABINET

DECAL INSTRUCTION DECAL - BOTTOM

INSTRUCTION DECAL - TOP

Figure 5: Cabinet Decal Installation

Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC. 3

Page 8

© GAPGON co-op, inc. STREET FIGHTER ALPHA3 ™

Re-assembly of Components

  • Notice that there are two white buttons. See figure 2. The WHITE buttons are START buttons. Install the PLAYER ONE button on the top left-hand side of the control panel, and the player two button on the top right-side of the control panel.

Figure 2: Start Buttons Red Green Blue Red Green Tel7 i eee 838 7 2 Player

Blue

Blue Red Green Red Green Blue

Buttons ——

Se NS

Retaining =)

Rings 5

  • <P Switches —— cB B Figure 3: Control Panel Buttons and Switches
  • Install all buttons and retaining rings on the control panel as shown in Figure 3. Install two red buttons to the immediate right of each joystick, install two green buttons to the right of the red ones, and install two blue buttons to the right of the green ones.
  • Install the switches on the buttons as shown in figure 3. Orient the switches so that when a button is pressed, the plastic contact on the switch is depressed.
  • Install the joysticks on the control panel as shown in figure 4.

Figure 4: Joystick Installation CONTROL PANEL WIRING

NOTE: all switch wires used in this game must be wired to the normally-open connection on the switches. Each switch requires a ground wire on the common connector and the appropriate control or switch wire on the normally-open connector of the switch.
  • Reconnect the existing JAMMA connectors to the control panel according to the chart in table 1.
  • Connect the player 1 and the player 2 kick buttons to the auxiliary cable harness as shown in figure
  • Make the connections according to the chart in table 2.

To Control Pane! Button Switches (Not Used)

To Volume / Test Switch Bracket vies Figure 6: Auxiliary Cable Harness

TEST SWITCH WIRING

  • Your cabinet may already equipped test switch. An optional test/volume bracket (see Figure 7) is available through your local CAPCOM distributor (part number 03-0050). When installing, the test switch bracket should be mounted inside the coin door and on top of the cash box for easy access. (See Page 7 for wiring detail)
NOTE: only the test switch is used for this game; the volume up/down switches are disabled. Volume adjustments must be made through the volume control knob located on the PC board.

-- Figure 7: Test Switch Bracket 24, If you are converting a cabinet that is equipped with CAPCOM® Q-SOUND, you may use stereo audio output connect to existing Q@-SOUND POWER AMPLIFIER.

o— Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN.OP, INC.

Page 9

® CAPCOM COIN-OP, INC. STREET FIGHTER ALPHA3 ™

A CAUTION

IMPROPER INSTALLATION OF THE JAMMA HARNESS TO THE GAME CARTRIDGE WILL CAUSE DAMAGE TO THE ENCLOSED PCB.

GAME CARTRIDGE INSTALLATION

“FULL” KIT

  • Install the four (4) mounting brackets to the underside of the “A” cartridge as shown in Figure 10.

Figure 10: Mounting Bracket Installation

  • Using the wood screws (Not Supplied), fasten the game cartridge case to the control panel shelf, as shown in Figure 11.

Figure 11: Case Mounting

22.

the audio cables. Connect the JAMMA harness connector and the auxiliary cable connector to the “A’ cartridge. If your cabinet is equipped with Q-SOUND, also attach

A WARNING

DISASSEMBLY OF EITHER GAME CARTRIDGE WILL VOID YOUR WARRANTY.

“B” KIT

  • To remove the existing “B” cartridge from the “A” cartridge, pull the old case clamps apart (see Figure 12). Carefully remove the old “B” cartridge and install the new “B’ cartridge. Re-install the case clamps.

"A" Cartridge

Figure 12 : Case Clamp Installation

  • Power-up the game and set all operator adjustable options by pressing the TEST switch. Follow the instructions under the TEST MENU section of this manual.

Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP. INC.

Page 10

® CAPGON COIN-OP, INC. STREET FIGHTER ALPHA3 ™

The test menu allows you to

TEST MENU

test the functions and configure the game. These items include input devices such as joysticks, buttons and coin door or switches, output devices such as monitor, speakers and meters. Through the Test Menu you can also access the Configuration Menu, where you can change the settings of the game.

TEST

INPUT

OUTPUT

  • ACCESSING THE TEST MENU MENU + For a CAPCOM® cabinet, or a cabinet with a test switch: Make sure the game is on and push the test switch. The screen shown left will appear. + For a cabinet without a test switch: SOUND & VOICE Push the blue test switch on the outside of the black plastic

COLOR casing. Refer to the inside back cover of the manual.

  • HOW TO SELECT AN ITEM

GAME DATA * Use the PLAYER 1 JOYSTICK to move the arrow in front

CONFIGURATION of the desired item and press the PLAYER 1 SHOT 1 button, as shown below in various MEMORY CHECK control panel configurations:

EXIT

SELECT = 1P UP or DOWN START =1PSHOT1

Player 1 Joystick Player 1 Start 2.

3.

  • DOT CROSS HATCH

6.

8.

9.

  • CLOSING THE TEST MENU To close the Test Menu, highlight “9. EXIT” and push the PLAYER 1 SHOT 1 button.
  • To return to the test menu, push the PLAYERI START and PLAYER 1 SHOT 1 buttons simultaneously.
  • The test menu will always return to the screen:

CAPERS. ora om Player 1 Shot 1 Player 1 Shot _&

  • After you exit the “7. CONFIGURATION MENU” and
  • After the memory is tested from the menu, “8. MEMORY CHECK”.

4, TEST MENU ITEM DESCRIPTIONS

INPUT Used to test all the input switches, such as joysticks and buttons. The “0” changes to a “1” as the button is pushed or joystick is moved. Check connections and switches in case the “0” doesn’t change to a “1” when depressed or moved. OUTPUT Used to test the coin meter and the coin lock. SOUND & VOICE Select a code of SOUND or VOICE with the PLAYER 1 JOYSTICK. Push the PLAYER 1 SHOT 1_button to hear the sound of the selected code. COLOR Shows color bars of red, green, blue, and white. Adjust RGB and brightness to obtain the optimum color balance and solid black background. DOT CROSS HATCH Used to test the screen size, focus and distortion. GAME DATA Coin meter, Free Game and Free play information will be displayed. CONFIGURATION Used to change the game play settings. Refer to the CONFIGURATION MENU section. MEMORY CHECK Used to test memory. “OK” appears when each block of memory passes test, “NG” appears in case of malfunction. If “NG” appears, repeat the memory test and wait for the “OK” message. Contact your distributor if “NG” still appears. EXIT Select this item and push the PLAYER 1 SHOT 1 button to return to game play mode.

6 Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC.

Page 11

® CAPCOM conor, inc. STREET FIGHTER ALPHA3 ™

CONFIGURATION MENU

The Configuration Menu is used to change various game settings such as level difficulty, credits, sound configuration, etc. These settings are stored in memory on the PCB.

The Configuration Menu is divided into 2 sections. In the SYSTEM section, you can change credits, sound, and coin door configurations. In the GAME section, you can change the play difficulty level and duration of the game.

  • ACCESSING THE CONFIGURATION CONFIGURATION MENU MENU

SYSTEM . From the TEST MENU, move the arrow to “7, CONFIGURATION” and push the PLAYER 1 SHOT 1 button. GAME ‘he screen left will be displayed

DEFAULT A description of each option is explained in the table below.

SAVE & EXIT

SELECT = 1PUPOR DOWN START = 1P SHOT1

  • CONFIGURATION MENU ITEM DESCRIPTIONS

SYSTEM Select this item to change settings for credits, monitor flip, sound and coin door configurations. GAME Select this item to change difficulty level, damage level, time count speed, maximum number of rounds and event type. DEFAULT | Use this item to restore configuration settings to the original factory values. Press the PLAYER 1 SHOT 1 and PLAYER 1 SHOT 2 buttons at the same time to restore default values. SAVE & | Use this to save new configuration settings and exit to the Test Menu. The message EXIT “SAVING NEW CONFIGURATION IN EE-PROM” will appear while the new settings are being saved. DO NOT turn power off to the game until “SAVING” is complete and the Test Menu reappears.

Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC. 1

Page 12

® CAPECL co-op, inc. STREET FIGHTER ALPHA3 ™

SYSTEM CONFIGURATION

7-1. SYSTEM CONFIGURATION CHANGING THE SYSTEM

COIN MODE2COIN1CREDITCONFIGURATION SETTINGS

CONTINUE ON

MONITORNORMALMove the PLAYER 1 JOYSTICK up or down to
DEMO SOUNDONhighlight the desired option.Once the option
SOUND MODESTEREO (Q SOUND)is highlighted, move the PLAYER 1
CHUTE TYPE2 CHUTES SINGLEJOYSTICK eft or right or press the PLAYER
REGULATIONONON1 SHOT 1 button to select.
  • EXIT

SELECT OPTION = 1P UP OR DOWN MODIFY SETTING = 1P LEFT OR RIGHT = 1P SHOT1 OR SHOT2

SYSTEM CONFIGURATION ITEM DESCRIPTIONS

  • COIN MODE SELECT THE CHARGE PER PLAY.
  • CONTINUE SELECT ON FOR CONTINUOUS PLAY OR OFF FOR NON-CONTINUOUS PLAY.
  • MONITOR FLIPS THE POSITION OF THE SCREEN. IF THE SCREEN APPEARS UPSIDE-DOWN, CHANGE THE SETTING TO FLIP; IF THE SCREEN APPEARS CORRECT, SELECT NORMAL. . DEMO SOUND TURNS ATTRACT SOUNDS ON OR OFF. . SOUND MODE SELECT STEREO OR MONAURAL FOR USE WITH YOUR CABINET. NOTE: STEREO SHOULD | ONLY BE SELECTED FOR USE WITH CAPCOM® QSOUND CABINETS. . CHUTE TYPE SELECT THE NUMBER OF PLAYER(S) AND COIN CHUTE TYPE. REGULATION If set to “ON” the color of the blood changes from red to white. . EXIT TO SAVE THE SETTINGS AND RETURN TO THE CONFIGURATION MENU, HIGHLIGHT THIS ITEM AND PUSH EITHER THE PLAYER 1 SHOT 1 BUTTON OR THE PLAYER 1 SHOT 2 BUTTON. rs a

sa @

SYSTEM CONFIGURATION OPTION SETTINGS

1. COIN MODE1 COIN1 COIN1 COIN1 COIN
1 CREDIT2 CREDITS3 CREDITS.4 CREDITS5 CREDITS
1 COIN1 COIN1 COIN1 COIN2 COINS
6 CREDITS7 CREDITS8 CREDITS9 CREDITS1 CREDIT
3 COINS4 COINS5 COINS6 COINS7 COINS
1 CREDIT1 CREDIT1 CREDIT1 CREDIT1 CREDIT

8 COINS 9 COINS 2 COINS START FREE PLAY 1 CREDIT LCREDIT 1 COIN CONTINUE OFF FLIP OFF STEREO (Q SOUND) MONAURAL 2 CHUTES SINGLE 2 CHUTES MULTI 1 CHUTE SINGLE 7, REGURATION ON OFF

NOTE: FACTORY SETTING

8 _ Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC.

Page 13

® CAPCOM coin-op, inc. STREET FIGHTER ALPHA3 ™

GAME CONFIGURATION

7-2. GAME CONFIGURATION CHANGING THE GAME CONFIGURATION SETTINGS

1.DIFFICULTYHARD 3
2.DAMAGELEVELNORMALMove the PLAYER 1 JOYSTICK up or
3.TIMER SPEEDNORMALdown to highlight the desired option.

Once the option is highlighted, move

4.GAME SPEEDTURBO 1the PLAYER 1 JOYSTICKleft or

5. 1P MAX ROUND 3 ROUNDS right or press the PLAYER 1 SHOT 1

6.2P MAX ROUND3 ROUNDSbutton ta select.
7.EVENTOFF
8.JOIN-INON

© EXIT

SELECT OPTION P UP OR DOWN MODIFY SETTINGS P LEFT OR RIGHT 1P SHOT1 OR SHOT2

ITEM DESCRIPTION OPTION SETTINGS

  • DIFFICULTY | SETS THE GAME DIFFICULTY LEVEL HARD 2 EXPERT
SETS THE OFFENSIVE POWER LEVEL.vNORMMAXIMUM

SETS THE SPEED OF COUNTDOWN FROM THE NORMAL FASTEST TIMER DISPLAY.

SET THE GAME SPEED. “TURBO 1” AND “TURBO TURBO 1 TURBO 2 FREE FREE 2” ALLOWS THE OPERATOR TO SET THE GAME SELECT 1 | SELECT 2 SPEED. “FREE SELECT 1” AND “FREE SELECT 2” ALLOW THE PLAYER SELECT THE GAME SPEED

SET THE NUMBER OF ROUNDS PER MATCH FOR 1 ROUND 3 ROUNDS 5 ROUNDS 1 PLAYER GAME (VS. CPU). DEFAULT IS SET AT 3 ROUNDS.

SET THE NUMBER OF ROUNDS PER MATCH FOR, 1 ROUND 3 ROUNDS 5 ROUNDS 2 PLAYER GAME (VS. PLAYER). DEFAULT IS SET AT 3 ROUNDS.

SPECIAL SETTING FOR TOURNAMENT EVENT. 1 MATCH 1 MATCH: ONLY ONE CREDIT IS REQUIRED FOR A 2 PLAYER GAME. THE GAME ENDS AFTER ONE MATCH REGARDLESS OF THE RESULT.

JOIN-IN SET THE OPTION TO ALLOW OTHER PLAYERS TO JOIN-IN. EXIT RETURN TO THE CONFIGURATION MENU.

NOTE: “JOIN-IN” WILL SET “OFF” AUTOMATICALLY WHEN “1 MATCH” IS SELECTED FOR “EVENT”.

Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC. 9

Page 14

® ICAIRCOM| COIN-OP, INC.

Table 1:

SOLDER SIDE STREET FIGHTER ALPHA3 ™

JAMMA Connections

COMPONENT SIDE

COIN COUNTER 1 COIN LOCK 2 COIN LOCK 1 *SPEAKER _(.) *SPEAKER (+) NIC NIC VIDEO GREEN VIDEO RED VIDEO SYNC VIDEO BLUE SERVICE (FREE CREDIT) VIDEO GROUND NIC DIAGNOSTICS 2 PLAYER - COIN 1 PLAYER _- COIN 2PLAYER_- START 1 PLAYER - START 2PLAYER_- UP 1PLAYER - UP 2PLAYER - DOWN 1PLAYER - DOWN 2 PLAYER - LEFT 1 PLAYER _- LEFT 2PLAYER_- RIGHT 1 PLAYER _- RIGHT 2 PLAYER 2 PLAYER

  • LIGHT PUNCH
  • MEDIUM PUNCH 1 PLAYER - LIGHT PUNCH
  • MEDIUM PUNCH 2PLAYER - HEAVY PUNCH
  • HEAVY PUNCH NIC

NIC NIC NIC NIC NIC NIC NIC PURPLE/YELLOW PLAYER 2 HEAVY KICK NIC NIC NIC NIC NIC PLAYER 1 HEAVY KICK NIC PLAYER 1 MEDIUM KICK NIC BLUE PLAYER 1 LIGHT KICK NIC GRAY/YELLOW PLAYER 2 LIGHT KICK NIC PINK/YELLOW PLAYER 2 MEDIUM KICK NIC NIC NIC NIC N/C GRAY/YELLOW TEST BRKT-VOLUME UP TEST BRKT-VOLUME DOWN __| PINK/YELLOW BLACK/WHITE TEST BRKT-VOLUME COMMON NIC

BLACK PLAYER 2 KICK - COMMON PLAYER 1 KICK-COMMON

Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC.

Page 15

® CAPCOM coin-op, inc. STREET FIGHTER ALPHA3 ™

REFERENCE INFORMATION

GAME CASE CONTROLS

COIN REGISTER METER (NOT USED) COMMUNICATION (NOT USED) PORTS (NOT USED) OUT IN

——s [oa Ss ll

*VOLUME UP

*VOLUME DOWN

JAMMA AUXILIARY CABLE AUDIO OUT (FOR Q SOUND) CONNECTOR CONNECTOR RIGHT: RED, LEFT: WHITE 300800

‘v1600200

Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC.

Page 16

NOTICE

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense.

WARNING

Federal law provides severe civil and criminal penalties for the unauthorized reproduction, distribution, or exhibition of copyrighted audiovisual works and video games.

The Federal Bureau of Investigation investigates allegations of criminal copyright infringement.

CAIRCOMY COIN-OP, INC. 475 Oakmead Parkway Sunnyvale, CA 94086 Phone: (408) 774-0500 Fax: (408) 522-5331

Copyright © 1998 CAPCOM ® coin-op, inc., All Rights Reserved