Blasteroids TM-316 1st Printing
Blasteroids (rev 4) (Atari Games, 1987) · Technical Manual · 68 pages · 73 sections · original scan
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
Blasteroids: Operators Manual with Illustrated Parts Lists
© 1988 by Atari Games Corporation. All rights reserved.
No part of this publication may be reproduced by any mechanical, photographic or electronic process, or in the form of a phonographic recording, nor may it be stored in a retrieval system, transmitted, or otherwise copied for public or private use, without permission from the publisher. The game play, all graphic designs, this technical manual, its accompanying schematic diagrams, and the display manual are protected by the U.S. Copyright Act of 1976. This Act provides for increased penalties for violating federal copyright laws. Courts can impound infringing articles while legal action is pending. If infringers are convicted, courts can order destruction of the infringing articles. In addition, the Act provides for payment of statutory damages of up to $250,000 in certain cases. Infringers may also have to pay costs and attorneys’ fees and face an imprisonment of up to five years. Atari Games Corporation will aggressively enforce its copyrights against infringers. We will use all legal means to immediately halt any manufacture, distribution, or operation of a copy of video games made by us. Anyone who purchases such copies risks forfeiting such a game.
Published by: Atari Games Corporation 675 Sycamore Drive P.O. Box 361110 Milpitas, California 95035
Printed in the U.S.A 28 Blasteroids
Blasteroids
Notice Regarding Non-Ataris Parts
You may void the game warranty (printed on the inside back cover of this manual) if you do any of the following: ¢ Substitute non-Atari parts in the game.
- Modify or alter any circuits in the game by using kits or parts not supplied by Atari Games Corporation.
NOTE
This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instruction manual, may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of Federal Communications Commission (FCC) Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area or modification to this equipment is likely to cause interference, in which case the user, at his own expense, will be required to take whatever measures may be required to correct the interference. If you suspect interference from an Atari game at your location, check the following: « All ground wires in the game are properly connected as shown in the game wiring diagram.
- The power cord is properly plugged into a grounded three wire outlet.
- On games provided with an Electromagnetic Interference (EMI) ground plane, be sure the game printed-circuit boards (PCBs) are properly installed on the EMI Ground Plane. If you are still unable to solve the interference problem, please contact Customer Service at Atari Games Corporation. See the inside front cover of this manual for service in your area.
Table of Contents
Set-Up Inspecting the Game... Control and Switch Locations . Game Play... Maximizing Earnings
Self-Test RAM/ROM Test... Switch Test Coin Options. Game Options.. Statistics Histograms Playfield Test Motion Object Test 2-6 Color Test... 2-6 Color Purity Test . Convergence Test Sound Test
Maintenance Preventive Maintenance. Preventive-Maintenance Interval: Removing the Control Panel... Cleaning the Push-Button Leaf Switche: Cleaning the Coin Mechanism... Cleaning the Interior Components Encoder Wheel Maintenance .. Corrective Maintenanc Removing the Video Display Replacing the Video Display Removing the Game PCB.. Removing the Fluorescent Removing the Speakers...
Troubleshooting Troubleshooting Aids Troubleshooting Techniq Soldering Techniques... Troubleshooting Static-Sensitive Devices . Illustrated Parts Lists
Blasteroids Coin Information and Game Statistics
Glossary
Warranty Blasteroids
Blasteroids
List of Illustrations
Figure 1-1
Figure 2-1 Figure 2-2 Figure 2-3 Figure 2-4 Figure 2-5 Figure 2-6 Figure 2-7 Figure 2-8 Figure 2-9 Figure 2-10 Figure 2-11 Figure 2-12 Figure 2-13
Figure 3-1 Figure 3-2 Figure 3-3
Figure 4-1 Figure 4-2 Figure 4-3 Figure 4-4
Figure 5-1 Figure 5-2 Figure 5-3 Figure 5-4 Figure 5-5 Figure 5-6 Figure 5-7 Figure 5-8
Table 1-1 Table 2-1 Table 2-2 Table 2-3 Table 2-4 Table 3-1 Control and Switch Locations
RAM Test Fails . 2-2 ROM Test Fails 2-2 Switch Test.. 23 Coin Option: 2-3 Game Options 24 Statistics 2-5 Histogra 25 Playfield Tes! 2-5 Motion Object Test 2-6 Color Test... . 2-6 Color Purity Test. - 26 Convergence Test . Sound Test
Leaf Switch and Encoder Wheel Removal . Encoder Wheel Disassembly and Lubrication Control Panel, Video Display, and Speaker Removal
Removing IC (Cut-Pin Method) . Removing IC Pins. Removing Solder from ‘oug! Removing Solder from Lead Connection Pad:
Cabinet-Mounted Assemblies. Control Panel Assembly Encoder Wheel Assembly Switching/Linear (SL) Power Supply Assembly. Coin Acceptors, Inc. Coin Door Assembh Blasteroids Game PCB Assembly .. Housequake PCB Assembly. Stand-Alone Audio PCB Assembly
List of Tables
Game Specifications. Faulty RAM Locations Faulty Program ROM Locations. Game Option Settings..... Faulty Sound RAM and ROM Locations.. Recommended Preventive-Maintenance Interval .
Safety Summary
The following safety precautions apply to all game operators and service personnel. Specific warnings and cautions will be found in this manual whenever they apply.
Chapter 1
Set-Up
How to Use This Manual
This manual is written for.game operators and service
- personnel, and provides information for setting up, playing, testing, and maintaining your Blastercids™ game. The manhal is ee into: the following chapters:
- Chapter.t contains setup and g game play informaton, 46 . %e . ‘Chapter 2 contains self-t test “procedures,
- Chapter 3 contains preventive and corrective maintenance procedures.” ‘see’ Chapter 4 contains troubleshooting information.
- Chapter 5 contains illustrated parts lists. Wiring and schematic diagrams for the Blasteroids game Circuitry are contained-in the Schematic Pack- “age Supplement (SP-316) included with your game. ‘This chapter includes information required to set up _ and play yout Blasteroids game. Carefully read the in- __ formation in th eet before applying power to the ganie, f
tee avoid electrical shock, do not. plag in the éabinet unti] it has been inspected and set up for the line voltage in-your aréa, ‘This cabinet “should only be. connected a grounded threeais you have only ioowite: outlet we recém- ~ mend that you hi ased electrician to in- | stall a grounded outlet. Players.can receive an”
electrical shock if the cabinet. is. not properly
grounded.
Set-Up
‘WARNING Do not plug in the game until you have completed the following inspection steps.
Inspecting the Game
Please inspect your Blasteroids game carefully to ensure that the game is complete and delivered to you in good condition. Figure 5-1 shows the locations of the component parts of the game. Table 1-i lists space, power, and environmental requirements. Inspect the factory-assembled game as follows:
- Examine the exterior of the cabinet for dents, chips, or broken parts.
- Unlock and open the rear access panel. Unlock and open the coin doors. Inspect the interior of the cabinet as follows: a. Ensure that all plug-in connectors (on the cabinet harnesses) are firmly plugged in. Do not force connectors together. The connectors are keyed so they only fit in the proper orientation. A reversed connector can damage a printed-circuit board (PCB) and will void your warranty. b. Ensure that all plug-in integrated circuits on each PCB are firmly plugged into their sockets. c. Inspect the power cord for any cuts or dents in the insulation. d. Inspect the power supply. Make sure that the correct fuses are installed. Check that the harness is plugged in correctly and that the fuse block cover is mounted in place. Check that the green ground wires are connected. e. Inspect other major sub-assemblies, such as the video display, printed-circuit boards (PCBs), and the speakers. Make sure that they are mounted securely and the ground wires are connected.
Table 1-1 Game Specifications
Characteristic Specification
Power Consumption B4V-A Temperature +5° to +38° C (437° to +100° F) Humidity Not to exceed 95% relative Line Voltage 102 to 132 VAC (US. games) Width 26.75 in. (70 cm) Depth 34,38 in. (87 cm) Height 70 in, (178 cm) Weight 302 Ibs. (137 kg) Blasteroids
Control and Switch
Locations
Power On/Off Switch The power on/off switch is located at the bottom rear of the cabinet. (See Figure 5-1.)
Volume Control The volume control is located on the Audio PCB behind the upper coin door. (See Figure 1-1.) The volume contro! adjusts the level of sound produced by the game.
Self-Test Switch The self-test switch is located to the left of the volume control on the Audio PCB behind the upper coin door. (See Figure 1-1.) Use the Self-Test switch to select the Self-Test Mode to check game operation. Refer to Chapter 2 for a complete description of self-test operation.
Coin Counter The coin counter is located on the shelf inside the upper coin door. The coin counter records the number of coins deposited. Auxiliary Coin Switches Two auxiliary coin switches are located on the lower part of the coin mechanism. Push either switch down to give one player coin.
Setting the Coin and Game Option Settings
Set the Blasteroids coin and game options in the Self- Test Mode. Refer to Chapter 2 for the recommended settings and the procedure for setting the options.
Game Play
This section of the manual describes the theme of the Blasteroids game and the game play. Introduction Blasteroids is an updated version of one of the most successful games in the history of the industry, Asteroids®, By taking this highly successful game concept of yesterday and combining it with the technology of today, Atari has created a unique attraction for a whole new generation of players.
Blasteroids
Auxiliary Coin Switches Self-Test Switch
Coin Counter Set-Up
Stand-Alone Audio PCB
Volume Control
Figure 1-1 Control and Switch Locations
Blasteroids is a one- or two-player game with a continuous buy-in feature allowing players to join in at any time. A color-coded control panel (left player red and tight player green) and spaceship allow for easy identification by players. Each player controls a whirly-gig and three buttons. The whirly-gig controls rotation, while the buttons control thrust, firing and the transformation of the spaceship. Attract Mode The Attract Mode begins when the game is powered up or after exiting the Piay or Self-Test Modes. The Attract Mode ends when coins or tokens are inserted and the start button is pressed. The Attract Mode continuously cycles through the following displays:
- Blasteroids title screen
- Game play demonstration alternates with the ship features screen ¢ Opponent characteristics
- High score table ¢ Audiovisual credits alternates with the scoring screen and the hints screen
Play Mode Players blast their way through numerous galaxies filled with asteroids and other challenging obstacles. After each galaxy has been cleared, the player meets Mukor, the green slime monster. Mukor taunts the player with one of several voice phrases, including “Mukor controls this galaxy.” The player can choose from four starting difficulties: easy, medium, hard, or expert. Each difficulty level is a game within itself; therefore, a player starting at the medium level will face a different challenge from a player beginning on the easy level. Unique Features to Attract Players Blasteroids has all of the proven player appeal of Atari’s 1979 classic hit, Asteroids, and adds all of the special game play features that today’s players expect.
- Distinctive transformation feature: At the press of a button, players can change their ship into three different sizes, each with its own advantages and disadvantages for different game play situations. The Speeder, the smallest ship, is the fastest. The Fighter, the medium ship, has the most firepower. The Warrior, the largest ship, has the best armor.
- Multiple opponents: Each of the six enemy ships (Sluggo, Dervish, Reboz, Bandit, Bumper and Bomber) has its own unique way of challenging the player. Energy leeches and the formidable Mukor must also be conquered.
- Special temporary powers: As the enemy ships are destroyed, their hidden cargo is revealed. Players can acquire special attributes from the debris of the enemy ships they conquer. There are Blasters and Power Shots for additional firepower, Shields for protection, Boosters for speed, Crystal Magnets to grab energy crystals, Extra Tanks to hold more energy, Cloaking Devices to hide from enemy ships, and Ripstars to wreak mass havoc.
- A hidden source of energy: Crystals concealed inside red asteroids provide players with the energy they need to continue their outer-space adventure.
Set-Up
¢ Powerful sound effects: Atari’s new Housequake™ sound system provides improved feedback to the player while drawing a crowd of spectators. The rumbling sound effects can be felt by players through the vibration of the game cabinet.
- Colorful, realistic graphics: Background spacescapes, pictures of space ships, asteroids and other obstacles are actually digitized pictures of real-life objects.
- Competition and cooperation for two players: Players compete with each other for special attributes and power crystals. Cooperation also pays off when two players dock their spaceships for added firepower and armor. Blasteroids’ one- or two-player simultaneous game play insures maximum earning potential. ° Atari’s maximum earnings features: Player-selectable level of initial difficulty, buy-in and add-acoin game continuation features,
High Score Mode Upon completing a game, if a player is among the top ten scorers recorded on the game, he can enter three initials. The player selects his initials by turning the player knob and pressing the fire button when the proper initial is displayed. The player can correct the initials by selecting the arrow that points to the left and pressing the fire button, then choosing the correct initials.
Maximizing Earnings
Operator options on this game have been kept very simple. Use the Self-Test Statistics and Histogram screens to evaluate game data and the Self-Test Game
1-4 Blasteroids
Options screen to make adjustments. The key to maximum earnings is striking a midpoint on game times. Game times must be short enough so that player turnover is high. Conversely, game times must be long enough to give a player a good value and insure repeat play (repeat play is crucial to longevity). Blasteroids gives the operator the flexibility to tune game difficulty and enough statistics to intelligently make adjustments. If collections seem low or are dropping off, first check all player controls and coin mechanisms for proper operation. If earnings are lower than usual for a game in your location, the game is technically sound and the average game time per quarter is under 110 seconds, try changing the game difficulty option to an easier setting. This change will give players more game time for their money. Change the option settings only one notch at a time and evaluate the change in game statistics that results. If the average game time per quarter is over 180 seconds, first try changing the game difficulty to a harder setting. If the average game time per quarter is still over 180 seconds after a few weeks, try an even harder setting. Again, it is important to change the difficulty settings one notch at a time and check game statistics before making further adjustments. If you change the game difficulty settings, it is a good idea to reset the game statistics. You can reset the coin information, game statistics and histograms in the Self- Test. Clear the coin information and game statistics at the statistics screen by simultaneously pressing the red Thrust and Transform buttons. Clear the histograms at the first histogram screen by simultaneously pressing the red Thrust and Transform buttons.
Chapter 2
Self-Test
The Blasteroids™ game tests itself and provides visual and audible indications of the condition of the game circuitry and controls. Self-test information is displayed on the screen and through the, sound system. No additonal equipment j is required.
“We suggest that you, perform a self-test when you first when you Suspect game failure
‘up the game, each time you:collect the money, and when you Suspect game failure. _ The self-test screens provide information about the game circuits, controls, and monitor adjustments. The game enters the Self-Test Mode after the self-test switch, is turned on. 2 switch.is on the front corner of the Stand-Alone Audio. PB located behind the upper coin door. S This chapter shows the self F-test screens in the order in which: you: will see them when the self-test switch is “tumed on. At the end, after the Sound Test, the se- "quence starts over with the Switch Test. When you are “finished with the Self-Test, turn off the Self-Test switch, and) the game will return to the Attract mode.
Self-Test
RAM/ROM Test The RAM/ROM Test screens are shown in Figures 2-4 and 2-2. This test provides a visual check of the game RAM, ROM, and associated circuitry. If the game passes the RAM/ROM Test, the display advances to the Switch Test. The RAM/ROM Test is divided into two sections. The RAM Test is performed first. If the game passes the RAM Test, then after a six-second delay, the self-test goes immediately to the ROM Test without displaying any message. If the game fails the RAM test, a message is displayed in the center of the screen. This message is shown in Table 2-1. The RAM Test continues to run until it passes. If you press and release the red Fire button, the RAM Test advances to the next RAM or ROM Test. If the game passes the ROM Test, no messages are displayed and the self-test advances to the Switch Test. If a ROM fails, a message is displayed. Table 2-2 shows the a message with the location of a failing ROM. If you press and release the red Fire button the ROM Test advances to the next ROM.
Table 2-1 Faulty RAM Locations
Video Location on RAM Type
Characteristic Game PCB
| Red | 6/7L | Upper Video RAM |
Background 5h Lower Video RAM
| Black | 16/17C | Upper Video RAM |
| Background | 15/16B | Lower Video RAM |
Table 2-2 Faulty Program ROM Locations
Error Location on
Address Game PCB
00000 U=6C L=6B 20000 U=4C L=4B Blasteroids
Figure 2-1 RAM Test Fails
fim, gi OG0000 error
Figure 2-2 ROM Test Fails
Switch Test
Use the Switch Test screen, shown in Figure 2-3, to check the condition of the controls. The Switch Test checks the following buttons: Left Spare Right Spare Left Xform Right Xform Left Thrust Right Thrust Left Fire Right Fire (Left and Right Spares are for factory use.) When you press a button, the name is highlighted on the screen if it is operating properly. Test the operation of the knobs by turning each knob quickly. Eight white numbers should appear below the “ted knob” and the “green knob” messages on the screen. If any of these numbers are red, the knob mechanism is not working correctly. If any numbers are yellow, the knob is operating poorly. If no num-
Blasteroids
bers appear, the mechanism is unplugged or defective. The number values are for factory use only.
Figure 2-3 Switch Test
Coin Options
The Coin Options screen, shown in Figure 2-4, shows the current coin settings. If you want to change these settings, use this screen. To move around the screen, hold down the red Transform button and turn the red knob. If you turn the knob clockwise, you will move down the settings list. If you turn it counterclockwise, you will move up the settings list. You can tell where you are on the screen by looking for the white box around the option. To change a coin option, release the red Transform button and tur the red knob. To cancel all the changes you have made, press the red Thrust button. This restores the settings used before you entered the Self-Test mode. To save all settings and go to the next screen, press the red Fire button. /f you turn off the self-test switch before you press the red Fire button, you will not save the selected coin settings. All of the default settings are shown in green letters. The following are the Blasteroids coin options:
- Game Price is the top line on the screen. Turn the red knob to change the game price to one of the four game price settings shown below: One Coin (Default) Three Coins Two Coins Four Coins
- Right Mech Multiplier is the second option on the screen. You can choose one of the following multiplier selections: 1 coin counts as 1 coin (Default) 1 coin counts as 4 coins 1 coin counts as 5 coins Self-Test
1 coin counts as 6 coins ¢ Left Mech Multiplier is the third option on the screen. You can choose one of the following multiplier selections: 1 coin counts as 1 coin (Default) 1 coin counts as 2 coins
- Bonus Adder is the last option on the screen. This option has the following settings: No bonus adder (Default) 2 coins give 1 extra coin 4 coins give 1 extra coin 4 coins give 2 extra coin 5 coins give 1 extra coin 3 coins give 1 extra coin Free play (Choose this if you want to use the Demonstration mode.) If you replace the EEROM at location 2A4/B or a hardware problem occurs, all of the coin options will change to the default settings.
Figure 2-4 Coin Options
Table 2-3 Game Option Settings
Option Name Available Settings
| Restore Factory Options | No | Yes |
Difficulty Level Easiest Medium Hard
Easier Hard
Easy Harder Medium Hardest
| Clear High | Yes+ | No |
Score Table Demo/Play Mode Playable Game Mode Demonstration Only Mode
| Music In Atiract | Yes | No |
+ Indicates default and manufacturer's recommended settings.
Self-Test
Game Options
The Game Options screen, shown in Figure 2-5, indicates the current game option settings. If you want to reset the Blasteroids game options, use this screen. The Game Option Settings Table, below, shows the available options and the default settings recommended by Atari Games. To move through the game options, hold down the red Transform button and turn the red knob. If you turn the knob clockwise, you will move down the option list. If you turn it counterclockwise, you will move up the option list. You can find your position on the screen by looking for the option with a white box around it. To change a game option, release the red Transform button and turn the red knob. To cancel all the changes you have made, press the red Thrust button. This restores the settings used before you entered the Self-Test mode. To save all settings and go to the next screen, press the red Fire button. If you turn off the self-test switch before you press the red Fire button, you willnot save the selected game options. The default settings on the Game Options screen are highlighted in green. The Game Option settings are:
- Restore Factory Options—If you select Yes, and exit from this screen using the red Fire button, your chosen game options will be cleared, the default settings will be used, and the High Score Screen will be cleared when the game returns to the Attract mode.
- Difficulty Level—This adjusts the difficulty in Blasteroids.
- Clear High Score Screen—If you select Yes, the High Score screen will be cleared.
- Demo/Play Mode—You can choose Demonstration mode or Play mode. To operate in the Demonstration mode, you must have Free Play specified in the Coin Option Bonus Adder setting.
- Music In Attract—Music is played in the Attract mode unless you select No.
Statistics
You can check the current game statistics on the statistics screen, shown in Figure 2-6. Use the information on this screen and on the histogram screens to fill out the Blasteroids statistics sheet in the back of this manual. The statistics information accumulates from the last time the statistics were cleared. If you want to clear the statistics information, simultaneously press the red
2-4 Blasteroids
Figure 2-5 Game Options
Thrust and Transform buttons. To go to the histograms, press the red Fire button. The following information appears on the Statistics screen:
- Left Coins shows the number of coins deposited in the left coin mechanism.
- Right Coins shows the number of coins deposited in the right coin mechanism.
- New Games shows the number of new games started.
- Continuation shows the number of times players continued their games.
- 0 Mins shows the number of minutes of idle time.
- 1 Mins shows the number of minutes played as a one-person game.
- 2 Mins shows the number of minutes played as a two-person game. Red Mins shows the number of minutes played on the red side.
- Green Mins shows the number of minutes played on the green side.
- Sessions shows the total number of sessions. One session is the time between the first player starting and both players dying, regardless of time, number of coins inserted, or how many people have played Blasteroids. ¢ Error Count shows the number of EEROM errors that were detected. Replace the EEROM at location 2A/B on the Game PCB if the errors detected exceed more than 75 per week.
- Total Coins shows the total number of coins deposited in both coin mechanisms.
- Avg Time/Coin shows the average game time per coin, in seconds.
Blasteroids
Figure 2-6 Statistics
:
Histograms
The seven histogram screens show the length of the games for both players in bar graph form. To move through the histogram screens, press the red Fire button. The first histogram screen is shown in Figure 2-7. The histogram information accumulates from the first time the game was turned on or from the last time the histograms were cleared. To clear the histograms, simultaneously press the red Thrust and Transform buttons, The first three histogram screens show the new game time in seconds for the easy, medium, and hard level selection. (The hard and expert player-selected levels are displayed together on the hard level screens in the game time and continuation time histograms.) The next three screens show continuation time in seconds for the easy, medium, and hard level selections. The final screen shows session length in minutes.
Figure 2-7 Histograms Self-Test
Playfield Test
The Playfield Test is shown in Figure 2-8. It tests the condition of the playfield circuit. If you see errors, check the circuitry and the ROMs at 1L and 1M on the Blasteroids PCB. (If your game has EPROMs instead of ROMs, check the EPROMs at 1L, 3L, 1M, and 3M on the Blasteroids PCB.) If you want to look at all the playfields, turn off the Self-Test switch while you are in the Self-Test Playfield screen. Next, press either the red Transform or Thrust button to advance through all the playfields. You can also see all the playfield screens as the game cycles through the Attract mode. If a screen is incorrect, this could indicate a failure in the playfield circuitry. Press the red Fire button to go to the next screen.
Figure 2-8 Playfield Test
Motion Object Test
The Motion Object Test is shown in Figure 2-9. The Motion Object Test indicates the condition of the motion-object buffer circuit. Hold down the green Thrust button and turn the green knob to see all the objects used in the game. To rotate an object, release the green Thrust button and turn the green knob. In the upper left corner of the screen are three lines of text. The first gives the number and short name of the object. The second gives the rotation view number and the name also. The last line gives the horizontal object size. Check to be sure all of the objects in the game are shown in the test. If an object is missing, you have a ROM error. Press the red Fire button to move to the next screen.
Self-Test
Figure 2-9 Motion Object Test
Color Test
The Color Test is shown in Figure 2-10. This test indicates the condition of the display color circuits. The screen should show 16 vertical grey-scale bars and three blocks of red, green, and blue, each containing 16 vertical bars. The brightest bars should be on the red and darkest (black) on the right with a grey frame around the screen. This frame helps to identify the darkest color band. If the display characteristics are not correct, refer to the display manual for the colorgun adjustment procedure or to determine the possible cause of failure. To adjust the brightness, find the Blasteroids
Table 2-5 Faulty Sound RAM and ROM Locations
Error Location on Stand-Alone Audio PCB
and Cause Message
Music Chip Time Out 2F Sound CPU Interrupt Error 2F, 5K, Transistor Q8 Sound CPU RAM 1 Error 2H Sound CPU ROM 1 Error 2K If this error is displayed when entering the test, then the sound processor cannot tun further. Press the red Fire button to obtain the next test. Communications Error #1 1M Counts the number of errors caused by either the Audio PCB or Game PCB. Indicates a probable disconnection of the Audio PCB from the Game PCB, or the chip at 1M is not inserted into its socket. Communications Error #2
darkest column (not black) with the red, green, and blue colors. This column should be just barely visible. Press the red Fire button to move to the next screen.
Color Purity Test
The Color Purity Test consists of five color displays that indicate the condition of the display color-purity circuits. The first display is a red screen with the word Red at the top of the screen as shown in Figure 2-11.
Figure 2-10 Color Test
2-6 Figure 2-11 Color Purity Test
Blasteroids
Press the red Thrust button, and the next display is green with the word Green at the top of the screen. Press the red Thrust button to obtain a blue, white, and finally a grey screen. After the grey screen, the display will repeat the red, green, blue, white, and grey sequence again. If the display characteristics are not correct, refer to the video display manual for the color-purity adjustment procedure or the possible cause of failure. Press the red Fire button to move to the next screen.
Convergence Test
The Convergence Test screen is shown in Figure 2-12. This test indicates the condition of the display size, centering, linearity, and convergence. The grid pattern should be white.
Figure 2-12 Convergence Test Press the red Thrust button and the grid pattern turns violet. Pressing the red Thrust button again causes the grid pattern to turn green. Check the grid pattern for the following characteristics:
- The four corners of the frame around the grid pattern should touch all four corners of the screen.
- Grid lines should show little pincushioning or barreling, and the lines should be straight within 1.2 mm.
- White pattern convergence should be within 1.5 mm. If the display characteristics are not within these limits, refer to the display manual for the linearity and convergence adjustment procedures or to determine the possible cause of failure. Use the violet and white patterns to adjust the display convergence. Press the red Fire button to move to the next screen.
Sound Test
The Sound Test screen is shown in Figure 2-13. This test indicates the condition of the coin mechanisms Self-Test
and the music, speech, and sound-effects circuits. The game may take up to three seconds to produce the first sound because the sound microprocessor is reset at the beginning of this test. If the sound-microprocessor resets correctly, check the coin mechanisms and the sound microprocessor citcuits as described below. If the sound microprocessor reset fails, the message SOUND PROCESSOR NOT RE- SPONDING should blink near the top of the screen. The sound test screen shows the following messages: © CURRENT COIN VALUE consists of four zeros. When you hold down the left coin switch mechanism, the third 0 changes to 1 and changes back to 0 when you release it, When you hold down the right coin switch mechanism, the fourth 0 changes to 1, then changes back to 0 when you release it.
- NUMBER OF SOUNDS indicates of the number of sounds used in the Blasteroids game. ¢ SOUND CPU STATUS indicates the condition of the sound microprocessor. If the sound microprocessor
Aud Player THros! Qufts
Figure 2-13 Sound Test
is good, the word Good appears. If the sound microprocessor or associated circuitry is faulty, a number will appear (to indicate sound status) in addition to an error message located at the top of the screen. Refer to Table 2-5 for the error messages and faulty sound RAM and ROM locations on the Audio PCB.
- SOUND # indicates the number of the sound. Choose a sound by turning the red knob. To hear the sound, press the red Thrust button one or more times. Press the red Transform button to silence the sound. You can also select the following integrated circuit (chip) tests during the Sound Test:
- Sound 4 (Music Chip Test) consists of eight tones in a major scale that alternate between sound channels (46 tones in all). Press the red Fire button to return to the Switch Test.
2-7
Self-Test
N
2-8 Blasteroids
S
Chapter 3
Maintenance
This chapter includes preventive and corrective maintenance procedures for the Blasteroids™ game components that are subject to the most use. To assure maximum trouble-free operation from this game, we recommend that you perform the preventive maintenance as described in this chapter.
Removal, disassembly, reassembly, and replacement
dures are providéd for components that might fequire corrective’ avant If a part is mentioned in the maintenancé procedures, but not illustrated, you __ can find it in Chapter 5, Illustrated Parts Lists.
Maintenance Blasteroids
Preventive Maintenance
Preventive maintenance includes cleaning, lubricating, and tightening hardware. How often you perform preventive maintenance depends upon the game environment and frequency of play. However, for the encoder wheel and the coin mechanism, we recommend that preventive maintenance be performed at the intervals specified in Table 3-1.
Preventive-Maintenance Intervals
The preventive-maintenance intervals in Table 3-1 are the minimum requirements for the components listed.
To avoid possible electrical shock, turn off the game before performing any maintenance procedures,
Table 3-1 Recommended Preventive- Maintenance Interval
Component Maintenance Interval
Encoder Wheel Inspect weekly, lubricate, and tighten hardware at least every six months. Inspect whenever you collect coins. Clean at least every three months, Coin Mechanism
Removing the Control
Panel
Perform the following procedure to remove/replace the control panel. (See Figure 3-1.)
- Turn off the game.
- Use the tamperproof hex-key wrench (included in the instruction manual bag) to remove the four tam- Perproof screws and washers holding the control panel to the cabinet.
A hole is provided on the cabinet shelf inside the upper coin door to store the hex-key wrench when not being used. This hole is located to the left of the coin slots.
3-2
- Pull the control panel towards you until you can tip the panel and reach underneath it.
- Disconnect the control panel harness connector. You can now remove the control panel from the cabinet.
- Replace the control panel in the reverse order of removal.
Players may receive an electrical shock if this control panel is not properly grounded! After servicing any parts on the panel, make sure that the green ground wire is firmly attached to the metal tab on the inside of the control panel. Only then should you lock up the game.
Cleaning the Push-Button
Leaf Switches Perform the following procedure to clean the leafswitch contacts and tighten the securing hardware. (See Figure 3-1.)
- Remove the control panel as previously described in this chapter.
- Use electrical contact cleaner to clean the contacts. Do not burnish them. When the push button is pressed, the wiping action of the cross-bar contacts provides a self-cleaning feature.
- Use a 15/16-inch open-end wrench to tighten the stamped nut holding the push-button leaf switches to the control panel. 4, Replace the control panel in the cabinet in the reverse order of removal. Use the Self-Test to verify proper switch contact.
Cleaning the Coin Mechanism Use a soft-bristled brush to remove loose dust or for eign material from the coin mechanism. A toothbrush can be used to remove any stubborn build-up of residue in the coin path. After cleaning the coin mechanism, blow out all of the dust with compressed air.
Cleaning the Interior Components Perform the following procedure to clean the components inside the cabinet.
Blasteroids
Carriage Bolt
Control Harness Assembly
Leaf Switch with Button Holder
Encoder Wheel Maintenance
Control Panel Decal
Control Panel
Flat Washer
Locknut
Retaining Ring
Assembly
Figure 3-1 Leaf Switch and Encoder Wheel Removal
Turn off the game power, but do not unplug the power cord before cleaning inside the cabinet. The power cord provides a ground path for stray static voltages that can be present on the cleaning tools,
- Unlock and open the rear access panel and display service panel.
- Discharge the high-voltage from the cathode-ray tube (CRT) before proceeding. The display assembly contains a circuit for discharging the high voltage to ground when power is removed. However, to make certain, always discharge the display as follows: a. Attach one end of a large, well-insulated, 18gauge jumper wire to ground. b. Momentarily touch the free end of the grounded jumper to the CRT anode by sliding it under the anode cap. c. Wait two minutes and repeat part b.
Be extremely careful when cleaning the electrical components inside the cabinet. Avoid touching the electrical components with any solid object other than the soft bristles of the vacuum attachment or paint brush,
w . Use a vacuum cleaner with a soft long-bristled brush attachment or use a soft-bristled paint brush to remove loose dirt and dust accumulated on the inside of the cabinet. Be sure to clean the electrical components thoroughly (power supplies, PCB assemblies, display, etc.).
The encoder wheel assembly is designed for maximum performance with minimum maintenance. To maintain this control, put two drops of a lightweight machine oil on each bearing once every six months. The encoder wheel must be disassembled in order to do this. Follow the next procedure and refer to Figure 3-1 and
Maintenance
Figure 3-2 before you begin the maintenance procedure. Figure 3-1 illustrates how the encoder wheel is removed from the control panel. Figure 3-2 illustrates the disassembled encoder wheel.
Plug
Encoder Wheel Bearing Key
Encoder Wheel
Gi Blasteroids
Removing the Encoder Wheel
- Remove the Contro! Panel from the game.
- Disconnect the 4-pin harness from the Coupler printed-circuit board (PCB).
- Use a flat-tipped screwdriver to pry the retaining clip off of the shaft of the knob. Save this retaining
Encoder Wheet Knob Groove for Retaining Clip
i Carriage Bolt
Encoder Wheel Housing
Retaining Ring
Figure 3-2 Encoder Wheel Disassembly and Lubrication
Blasteroids
clip for reassembly. The encoder wheel knob can be removed now from the top of the control board.
The retainer can fly off at a high speed when you are prying it off. Be sure to cover the retainer with a rag or block it with your hand so that the retainer will not be lost if it flies off.
4, Remove the two locknuts and washers from each encoder. Now you can remove the encoder from the long carriage bolts that hold it onto the control panel. Remove the carriage bolts, nuts, and washers. Save this hardware for reassembly. Opening the Encoder Wheel Housing
- Use a Phillips-head screwdriver to remove the screws that attach the Coupler PCB to the housing. Carefully remove the Coupler PCB.
- Two identical parts snap together to form the housing for the encoder wheel. To unsnap these two parts, place two fingertips on the tabs that protrude on one end of the housing. Pull these tabs away from the center of the housing until they release. Turn the housing over and place two fingertips on the tabs that protrude on the other end of the housing. Pull these tabs away from the center of the housing until they release.
- Pull the bottom half of the housing off, leaving the encoder wheel and the top half of the housing together. 4, Pry off the aluminum sleeve around the knob insertion hole. Remove the encoder wheel from the housing. . Check the plugs in the encoder wheel. They should be evenly spaced. If they are not, poke them out from the back and reposition them.
Lubricating the Encoder Wheel
Remove the identical plastic flange bearings on either side of the coder wheel by sliding them off of the shaft. Apply one drop of a lightweight machine oil to the flat surface that touches the encoder wheel and one drop to the inside diameter of each bearing. Put a light coating of grease on the encoder wheel knob spline. Reassembling the Encoder Wheel Housing
- Put a bearing in each housing and line up the key on the bearing with the groove near the center hole of each housing. wa Maintenance
- Find the housing half with the threaded holes in the side for the Coupler PCB. Find the encoder wheel shaft end that does not have the splined hole. Insert this shaft end into the bearing in this housing half.
- Insert the shaft with the splined hole into the other half of the housing. Make sure that the bearing key does not leave the encoder housing groove.
- Push the two halves of the housing together, and make sure the tabs click closed. If the two halves will not fit together, probably the bearing keys are not in the encoder housing grooves. yw . Push the aluminum sleeve over the spine hole end of the encoder and make sure the sleeve is flush with the top of the encoder wheel shaft.
- Use a Phillips-head screwdriver to reattach the Coupler PCB to the threaded holes in the housing. The components on the Coupler PCB should face in towards the encoder wheel, and the encoder wheel should be between optical couplers. Attaching the Encoder Wheel Assembly To the Control Panel
- Place the encoder wheel housing against the control panel, with the splined hole facing the control panel, and the pins on the Coupler PCB facing away from it.
- Insert the carriage bolts through the control panel, the encoder wheel housing, and the washers. Screw on the nuts. . Use a 3/8-inch hex driver to tighten the nuts. . Connect the 4-pin harness to the Coupler PCB. Wo we . From the player side of the control panel, insert the encoder wheel knob into the housing.
- Place the retaining clip on the shaft of the encoder knob in the groove closest to the housing.
- Reconnect the game harness assembly. Do not force the connectors together. Be sure you have them in proper configuration.
- Slide the control panel onto the cabinet.
- Screw in the four tamperproof screws and washers.
3-5
Maintenance Blasteroids
Corrective Maintenance
Corrective maintenance consists of removal, disassembly, reassembly, and replacement of game components. The following procedures are provided for components that may require corrective maintenance.
Removing the Video Display
Perform the following procedure to remove or replace the video display. (See Figure 3-3.)
- Turn the game power off and wait two minutes. Unplug the power cord.
- Remove the control panel.
- Remove the video display shield by sliding it down, out of the slot in the cabinet which holds the shield’s top edge. Bring the shield towards you, sliding its bottom edge across the area where the control panel was located.
- Carefully remove the bezel from the protective foam tape on the back.
Sharp Video Display
\ Display Bezel i i
r i ' i I ' i i i i i i i i ‘ i i '
Le
Bracket Display Shield
Encoder Whee! Knob
Control Panel
Encoder
Figure 3-3 Control Panel, Video Display, and Speaker Removal
3-6
The video display contains lethal high voltages. To avoid injury, do not attempt to service this display until you observe all precautions necessary for working on high-voltage equipment. The video display has been designed to minimize X-radiation. However, to avoid possible exposure to soft X-radiation, do not modify the high-voltage circuitry. The cathode-ray tube may implode if struck or dropped. Shattered glass may cause injury within a 6-foot radius. Use care when handling the display.
Attraction Shield
Control Mounting 4
- Discharge the cathode-ray tube (CRT). Be sure that the game power is turned off. Although the display assembly contains a circuit for discharging the high voltage to ground when power is removed, to be certain, always discharge the display as follows. a. Attach one end of a large, well-insulated, 18gauge jumper wire to ground. b. Momentarily touch the free end of the grounded 41/2" Round Speaker
Speaker Grille
Ss 7
Blasteroids
jumper to the CRT anode by sliding it under the anode cap. c. Wait two minutes and repeat part b.
- From the rear of the cabinet, disconnect the display harness connectors from the display.
‘WARNING
To avoid dropping the video display, use extreme care when removing the display from the cabinet. ‘We recommend that no one weighing less than 150 pounds should attempt to remove the display. In addition, we recommend that you wear gloves to protect your hands from the sheet-metal edges.
- Use a 3/8-inch nut driver to loosen the four nuts and washers holding the display to the cabinet mounting panel.
- Carefully lift the display out through the front of the cabinet.
- Replace the video display as described in the following procedure.
Replacing the Video Display
Whenever the cathode-ray tube and yoke are replaced as a single unit, readjust the brightness, size, and centering as described in the video display manual. Check the purity and convergence also according to the display manual instructions, but adjust these only if required.
Perform the following procedure to replace the video display in the cabinet. (See Figure 3-3.)
- Carefully lift the video display through the front of the cabinet.
- Position the display so that the four holes in the two mounting brackets align with the four studs in the cabinet.
- Tighten the four mounting nuts and washers holding the mounting brackets to the cabinet studs. Use a 3/8-inch nut driver. 4, Connect the display harnesses to the display.
- Replace the bezel and display shield. Replace the control panel. Maintenance
Removing the Game PCB
Perform the following procedure to remove or replace the Game PCB. 1, Turn the game power off.
- Unlock and remove the rear access panel from the cabinet. 3, Disconnect the harness connectors from the Game PCB. ; 4, Use a Phillips screwdriver to remove the two screws and washers holding the Game PCB to the cabinet. . Grasp the edge of the Game PCB and gently lift it out of the slotted guide.
- Replace the Game PCB in the reverse order of removal.
Removing the Fluorescent Light
Perform the following procedure to remove or replace the fluorescent light. (See Figure 3-3.)
- Turn the game power off.
- Use a 1/8-inch hex driver to remove the three screws in the retainer on the top of the cabinet which hold the attraction shield in place. Remove the retainer. > vw
- Remove the attraction shield. The shield has foam tape on the front and back edges. 4, Remove the fluorescent light from the light fixture.
- To remove the entire light fixture, disconnect the light harness connector in the rear of the cabinet.
- Use a Phillips screwdriver to remove the two screws holding the light fixture. Remove the light fixture.
- Replace the fluorescent light and/or light fixture in the reverse order of removal.
Removing the Speakers
Perform the following procedure to remove or replace the speakers. (See Figure 3-3.)
- Turn the game power off.
- Unfasten the grille. a, Upper Speakers—Use a 1/8-inch hex driver to remove the eight screws holding the speaker grille to the cabinet. Remove the grille. b. Lower Speaker—Use a 1/8-inch hex driver to remove the four screws holding the speaker grille to the cabinet. Remove the grille.
Maintenance
- Use a Phillips screwdriver to remove the four screws holding each speaker to the cabinet. Do not let the speaker fall.
- Remove the speaker just far enough to disconnect Blasteroids
the two speaker wires. When you reassemble the speaker and the wires, be sure that you hook up the wires correctly. Otherwise, the game will produce less than the desired volume because the speakers will be out of phase. The signal wire for each speaker should be attached to the speaker tab marked with color, a + sign, or a round dot. (The signal wires are shown on the game wiring diagram; refer to the Schematic Package included with the game.) . Replace the speaker in the reverse order of removal.
Chapter 4
Troubleshooting
The information in this chapter discusses troubleshooting aids and techniques to assist the service technician when trouble is suspected in a game. Most troubles can be located quickly, by following the information in this.chapter. However, if problems persist, contact yout local distributor if Atari Games Corporation Customer Service O: listed onthe inside front cov-
We recommend that troubleshooting and repair
procedures be performed by a qualified service technician: ‘j
Troubleshooting
Troubleshooting Aids
Troubleshooting aids are provided in this manual and in the schematic package supplement. The most useful of these are:
Assembly and Component Locations The locations of assemblies and components are in the parts lists in Chapter 5 of this manual. The. Printed-circuit board (PCB) illustrations can aid in rapidly locating components shown on the corresponding schematic diagram(s). Diagrams The schematic package supplement for this manual contains schematic diagrams with component locations, active component type numbers, and electrical values.
Troubleshooting Techniques
To avoid electrical shock, turn off the game power before attempting to troubleshoot this game.
The following troubleshooting steps are arranged in a sequence recommended for locating a defective component. The procedure begins with a check of the simple trouble possibilities and progresses to more extensive procedures for localizing the problem to an assembly or major circuit, and then to a defective component. Check Fuses Check for open fuses. Refer to the power supply parts list in Chapter 5 and to the schematic package supplement for the location and rating of each fuse used in this game. Make sure that replacement fuses are the proper type and rating.
Check Power-Supply Voltages
If all circuits are operating improperly, this usually indicates a power supply problem. Be sure that the proper line voltage is available to the power supply. Refer to the label on the power supply for its voltage rating. Locate the Trouble Decide what the symptom is. Perform the self-test procedure provided in Chapter 2 of this manual. Use the wiring diagrams in the schematic package supplement to determine which assemblies or major circuits may be causing the trouble.
4-2 Blasteroids
Visual Check Visually check for obvious problems in the portion of the game where the trouble is suspected. For example, check for loose or defective solder connections, integrated circuits loose in their sockets, loose cable connections, broken wires, and damaged PCBs or components.
Check Individual Components Check soldered-in passive components (e.g., resistors, capacitors, diodes) by disconnecting one end to isolate the measurement from the effects of the surrounding circuitry. Often, the most practical way to determine if a component is faulty is to substitute a new component. Before you do this, make sure that you do not have some other circuit problem that could damage the new component.
Repair the Assembly
Soldered-in transistors and integrated circuits are difficult to remove without damaging the printed-circuit board or component. Refer to the information in this chapter pertaining to soldering and replacing integrated circuits and transistors.
Repair or replace the defective part. Refer to Chapter 4 and information in this chapter for special removal and replacement procedures. Check for proper operation of the repaired circuit.
Soldering Techniques
Observe the following recommendations when removing or replacing components soldered to a PCB. You can damage a PCB or heat-sensitive electrical components with poor soldering practices. Choose the proper soldering iron before you attempt to remove or replace soldered-in components. Excessive heat from a soldering iron is a common cause of damage to a component or PCB. Also, transient voltages from solder guns or improperly grounded soldering irons can damage certain voltage-sensitive semiconductor devices. Refer to Troubleshooting Static-Sensitive Devices for more specific information. We recommend a 15- to 27-watt pencil-tip soldering iron to avoid separating the etched circuit wiring from the board material and to avoid damaging active components. You can also use a temperature-controlled. soldering station rated at 700° F with a fine cone or a very fine chisel tip.
Blasteroids
Do not use a solder gun to remove or replace soldered-in components on a printed circuit board, A solder gun can overheat a device, and its large transient voltage can damage a voltagesensitive device.
You will also need the following additional equipment for removing and replacing soldered-in components: © Solder Sucker—Hand-operated vacuum tool to remove liquified solder from the PCB. We recommend the top-of-the-line Soldapullt® brand.
- Solder Wick—Resin-soaked copper braid to remove excess solder from the lead connections on the PCB. See Removing Integrated Circuits for precautions relating to the use of a solder wick on a multi-layer PCB with plated-through holes. + Flux Remover—Non-corrosive chemical to clean foreign material from the PCB before soldering and to remove any flux residue where components have been replaced. Also use it to clean any foreign material from the PCB during preventive maintenance. Isopropyl alcohol is recommended. ¢ Acid Brush—Small stiff-bristled paint or toothbrush used with flux remover to clean flux and other foreign material from the PCB. Removing Integrated Circuits The easiest and safest method for removing solderedin integrated circuits (IC) from a PCB is to cut off each pin as close to the IC case as possible with a tip dyke (diagonal cutter) as shown in Figure 4-1. Use the proper soldering iron as previously described under Soldering Techniques. Then, to avoid excessive heat buildup in one area of the PCB, apply heat directly to each pin in a random order. Remove the loosened pin with the tip of the soldering iron or a needlenose pliers as shown in Figure 4-2. Allow a moment for the PCB to cool before proceeding to the next pin. Apply just enough heat to remove any stubborn pins.
Diagonal Cutter
Figure 4-1 Removing IC (Cut-Pin Method) Troubleshooting
Needle-Nose Pliers
Soldering Iron
Figure 4-2 Removing IC Pins For a multi-layer PCB with plated-through holes, use a solder sucker to remove the remaining solder from inside each hole as shown in Figure 4-3. If possible, suck the solder from the opposite side of the PCB from where the heat is applied. Use a solder wick to remove excess solder from around the lead connection pads on the top and/or bottom surface of the PCB as shown in Figure 4-4.
Do not use a solder wick to remove solder from. inside plated-through holes. The heat required for the solder wick to remove the solder from inside the hole could damage the PCB.
Use an integrated-circuit (IC) pulling tool to remove socketed ICs. Do not pry up on one end of the ICs because the pins could be bent or broken.
Troubleshooting Static-
Sensitive Devices
Certain precautions must be taken when working with static-sensitive devices, such as microprocessors, fieldeffect transistors (FET), complementary metal-oxide semiconductors (CMOS), and other large-scale integration (LSI) devices that use metal-oxide semiconductor (MOS) technology. Static charge buildup in a person's body or leakage from an improperly grounded soldering iron can cause static-sensitive device to fail. Before handling a static-sensitive device or a PCB with such devices attached to it, ground any static voltage that may have accumulated in your body by touching an object that has been earth grounded. A bare wire wrapped around your wrist and attached to an earth ground is effective when working extensively with Static-sensitive devices. When soldering a static-sensi-
4-3
Troubleshooting
Soldering Iron
- “ _
Solder Sucker
Preferred Method Blasteroids
Soldering Iron
Alternate Method
Figure 4-3 Removing Solder from Plated-Through Holes
Soldering Iron Solder Wick
Figure 4-4 Removing Solder from Lead Connection Pads tive device, use a soldering iron with a properly grounded three-wire cord. (Refer to Soldering Techniques for a discussion of recommended soldering irons and procedures.) Before you replace a static-sensitive device, make sure it is actually defective. A static-sensitive device can appear defective due to leakage on a PCB. To make sure a device is defective, ground static voltages as described in the paragraph above. Clean both sides of the PCB with flux remover or an eraser. For discrete FETs, clean thoroughly between the gate, drain, and source leads. Then test the device. New static-sensitive devices can be packaged in conductive foam or can have a protective shorting wire attached to the pins. Remove the conductive foam just prior to inserting the device into its socket or soldering it to a PCB. Remove the shorting wire only after the device is inserted into its socket or after all the leads are soldered in place.
Chapter 5
Ihustrated Parts Lists
This chapter provides information you need to order parts for your game. Common hardware parts, such as screws, nuts, washers,.and so on, are not in the parts
Bi parts lists are” crane in alphabetical order
sts z arranged alphanumerically by ese parts listsyall A-prefix € cOme part numbers with a list are: part numbers with six through'99-). ee
hyphen (000598- through
numbers followed
: Parts, give the part number, part ae the number of this manual, and the serial num-
Illustrated Parts Lists Blasteroids
A045045-01 045008-01 ‘ A045044-01 Display Harness Assy Attraction Decal Speaker Harness Assy 139021-001 045007-01 034536-02 448007-003 Sharp Video Display Attraction Shield Foam Vibration Damper 4 4/2" Round Speaker 045009-01 “4 0 aati 043276-03 045011-01 Display Bezel Retainer Speaker Grille
i ‘ 170003-001 178056-002 Flurescent Lamp Foam Tape 171086-001 Fluorescent Lamp Fixture 99-11006 Edging Trim Clip Retainer L-
Control Mounting Bracket 045010-01 Display Shield
178120-606 Control Panel Assy PCB Support See Figure 5-2 176025-3620 Tamper Proof Screw 75-015F Flat Black Washer 78-6900402 Foam Tape
Encoder Assy See Figure 5-3 044050-01 Round Woofer 148011-001 8-Inch Round Woofer, A045003-01 Cabinet Assembly Coin Door 038091-01 See Figure 5-5 Molded Coin Box SA Audio PCB Assy Hex-Key Wrench See Figure 5-8 Storage Hole 171078-002 178126-002 Coin Counter Tamper Proof Hex Key
Figure 5-1 Cabinet-Mounted Assemblies A045000-01 B
Illustrated Parts Lists Blasteroids
House Quake PCB Assy
178129-001 Wire Routing Clip
045025-01 Upper Rear Door °
045013-04 Lower Right Panel Decal
045021-01 Rear Door
178093-001 Fan Blade Guard 4
A043055-01 On/Off Harness Assy
Power Supply Assy See Figure 5-4 Blasteroids PCB Assy See Figure 5-6
Figure 5-1 Cabinet-Mounted Assemblies, Continued.
Ulustrated Parts Lists Blasteroids
Cabinet-Mounted Assemblies Parts List
Part No. Description
A043055-01 12-Inch-Long On/Off Harness Assembly
| A043713-22 | SA Audio PCB Assembly | ‘ |
A044326-21 Main Blasteroids PCB Assembly A044872-03 Power Supply Assembly
A044875-01 AC Power Harness Assembly ‘A045003-01 Cabinet Assembly A045004-01 Control Panel Assembly A045040-01° Communication/Audio (Com/Aud) Harness Assembly
A045041-01 Coin Harness Assembly A045042-01 Cabinet Harness Assembly A045044-01 Speaker Harness Assembly A045045-01 Display Harness Assembly A045046-01 Power Harness Assembly A045050-01 Housequake PCB Assembly 034536-02 Foam Vibration Damper (0.50-Inch Thick) 037332-01 Louvered Grille
038091-01 Molded Coin Box 043276-03 22.20-Inch-Long Machined Retainer 044050-01 Square Grille Speaker
| 045007-01 | Attraction Shield | , |
045008-01 Attraction Decal 045009-01 Video Display Bezel
| 045010-01 | Tinted Display Shield | . |
045011-01 Speaker Grille
045013-01 Upper Left Panel Decal 045013-02 Upper Right Panel Decal 045013-03 Lower Left Panel Decal 045013-04 Lower Right Panel Decal
045021-01 Rear Door 045025-01 Upper Rear Door 045056-01 Edging Trim 045057-01 Control Mounting Bracket
139021-001 Sharp Model #XM-2001N 19-Inch Color Raster Video Display 148007-003 4 1/2-Inch Round Unshielded Speaker 148011-001 8-Inch Round Woofer (Acceptable Substitute is part number 148008-002, 8-Inch Round Speaker) 170003-001 18-Jnch-Long SOW Fluorescent Lamp
171027-001 Over/Under 25¢/25¢ Coin Door
| 171078-002 | Non-Resettable 12VDC Coin Counter | ‘ |
171086-001 118V 60Hz 18-Inch-Long Fluorescent Lamp Fixture 175007-001 #10 Flat Fender Washer
| 176025-3620 | Tamper-Proof Screw | , |
178056-002 1/2Anch Wide x 1/16-Inch Thick Foam Tape (64 Inches) 178093-001 Fan Blade Guard 178126-002 ‘Tamper-Proof 5/32-Inch Hex Key
5-4
Blasteroids Illustrated Parts Lists
Cabinet-Mounted Assemblies Parts List, Continued
Part No. Description 178129-001 Wire Routing Clip 75-015F Flat Black 1/4-Inch Washer 78-6900402 1/4-Inch Wide x 1/8-Inch Thick Foam Tape (48 Inches) 99-11006 Fluorescent Lamp Clip Retainer
The following items are the technical information supplements for this game:
TM-304 Sharp (Model # XM-2001N) Video Display Manual
SP-316 Blasteroids Schematic Package ST-316 Blasteroids Self-Test Label
TM-316 Blasteroids Operator's Manual
ye Ov
Illustrated Parts Lists
045006-01 75-5140B Carriage Bolt Controi Panel Decal
178030-004 Red Button Assy
S ~— 045005-01 A045043-01 — £ Control Panel Contro} Harness Assy
175002-002 178030-005 Green Button Assy Flat Washer
>» @ fa 177010-240 Locknut
178012-005 Retaining Ring A038023-01 Encoder Wheel Assy
75-9910NO Blasteroids
Stamped Nut
160013-002 Leaf Switch With Button Holder
Figure 5-2 Control Panel Assembly A045004-01 A
Control Panel Assembly Parts List
Part No. Description
A038023-01 Encoder Wheel Assembly A045043-01 Control Harness Assembly 75-5140B #10-24 X 2.50-Inch Black Carriage Bolt 75-9910NO 5/8-Inch #11 Stamped Nut 045005-01 Control Panel 045006-01 Control Panel Decal 160013-002 Leaf Switch With Button Holder and Cross Bar 175002-002 #10 Flat Washer 177010-240 #10-24 Locknut 178030-004 Red Button Assembly 178030-005 Green Button Assembly
5-6
Blasteroids Illustrated Parts Lists
038319-01 Encoder Wheel Knob oi WARNING Groove for ers may receive an electrical riches shock ithe contra panel sno prop: Retaining Clip erly graunded! Atter servicing any parts on the panei, make sure that .
tached tothe metal tab onthe inside Carriage Bolt ofthe control panel. Only then should 042786-01 a you lock up the game. Encoder Wheel Sleeve
038026-01 D Encoder Wheel Housing
Bearing Key
038011-01 Encoder Wheel Plug
038011-01 Encoder Wheel pS 107013-001 Light Oil
038022-01 Tabs Flange Bearing
[Housing
Groove
Washer
A044980-01 ' Coupler PCB Assembly Nut
178012-005 Retaining Ring
72-JB3606 Screw
Figure 5-3 Encoder Wheel Assembly A038023-01 E
Illustrated Parts Lists Blasteroids
Encoder Wheel Assembly Parts List
Part No. Description A044980-01 PCB Coupler Assembly 72-JB3606 Twin Helix Plastite Hex #6 Screw 038010-01 Encoder Wheel 038011-01 Encoder Wheel Plug 038022-01 Hange Bearing 038026-01 Encoder Wheel Housing 038319-01 Encoder Wheel Knob 042786-01 Encoder Wheel Sleeve 107013-001 Light Oil 178012-005 0.156 Inch Diameter Shaft Retaining Ring 178027-001 Grease
Blasteroids Mllustrated Parts Lists
4& WARNING A The switching power supply has high voltages on it when power is turned on. Therefore, be sure you do not touch this power supply unless you have turned off the power to the game.
149003-XXX 72-HA4606S 8V 10 Amp Switching Power Supply Assy
A043367-XX 179231-002 Jumper Assy Terminal Block 142042-001 Transformer
A043367-XX Jumper Assy A043366-01 5V Harness Assy 72-HA4806S, Screw
043396-01 Power Supply Chassis Base
A042384-01 Line Filter Assy
46-2013002 Fuse
037640-01
- Fuse Block 034544-01 Fuse Block Cover
043622-01 Fuse Label
Figure 5-4 Switching/Linear (SL) Power Supply Assembly A044872-03 A
Illustrated Parts Lists Blasteroids
Swiiching/Linear (SL) Power Supply Assembly Parts List
Part No. Description
A042384-01 Line Filter Assembly A043367-01 Jumper Assembly A043367-02 Inch Black Jumper Assembly 4043367-03 6-Inch White Jumper Assembly
A043909-01 5 V Harness Assembly 46-2012002 250 V Slow-Blow 2 A Fuse 46-2013002 250 V Slow-Blow 3 A Fuse 72-HA4606S #6-32 x 3/8-Inch Cross-Recessed Pan-Head Thread-Forming Screw 72-HA4806S, #8-32 x 3/8-Inch Cross-Recessed Pan-Head Thread-Forming Screw 034544.01 Fuse Block Cover 037640-01 Power Supply Warning Label 043396-01 Power Supply Chassis Base
04362201 Power Supply Fuse Label 142047-001 Transformer 149003-003 Hitron 5 V 10 A Switching Power Supply Subassembly 179225-2205 5-Position Fuse Block (Acceptable substitute is part no. 79-3206) 179231-002 2-Position Terminal Block
Hitron 5-Volt Power Supply Sub-Assembly Model HSA-122B(S) Parts List
| Designator | Description | Part No. |
Capacitors
| cl | Capacitor, Metal Film, 0.047 pF 250 V. | 99-211036 |
| C2 | Capacitor, Metal Film, 0.1 ¢F, 400 V | 99-211038 |
| C3, C4 | Capacitor, Ceramic, 4700 nF, 400 V | 99-211049 |
| C5, C6 | Capacitor, Electrolytic, 100 uF, 200 V | 99-211046 |
| C7 | Capacitor, Metal Film, 0.1 p& 400 V | 99-211038 |
| C8 | Capacitor, Ceramic, 0.001 #F 2 kV | 99-211042 |
| co | Capacitor, Ceramic, 0.01 pF, 1 kV, Z5U | 99-211041 |
| C10 | Capacitor, Electrolytic, 220 wE 25 V | 99-211045 |
| ci | Capacitor, Metal Film, 0.22 wE, 100 V | 99-211037 |
| C12 | Capacitor, Metal Film, 0.022 pF, 100 V | 99-211039 |
| C13 | Capacitor, Metal Film, 0.22 wF, 100 V | 99-211037 |
| C14 | Capacitor, Ceramic, 1800 PF 2 kV, Z5 V | 99-211040 |
| cl7 | Capacitor, Electrolytic, 470 pF, 25 V | 99-211044 |
| c19 | Capacitor, Electrolytic, 2200 wF, 16 V | 99-211048 |
| C20 | Capacitor, Electrolytic, 1000 wR 25 V | 99-211047 |
| C21 | Capacitor, Ceramic, 470 PF, 1 kV, Z5SP | 99-211043 |
| C22 | Capacitor, Electrolytic, 2200 pE 16 V | 99-211048 |
| C23, | Capacitor, Electrolytic, 1000 pF 25 V | 99-211047 |
| C24 | Capacitor, Electrolytic, 2200 pk 16 V | 99-211048 |
Diodes
| D1, D2 | Diode, Fast Recovery, RPG10K | 99-211010 |
| D3 | Diode, Fast Recovery, RPG15B. | 99-211011 |
| D4 | Diode, Fast Recovery, RPG10B | 99-211009 |
| DS5-D7 | Diode, Switching, 1N4148 | 99-211012 |
5-10
Blasteroids Illustrated Parts Lists
Hitron 5-Volt Power Supply Sub-Assembly Model HSA-122B(S) Parts List, Continued
| Designator | Description | Part No. |
D9 Diode, Fast Recover > Y, 30DF1 99-211006
| DI, Diz | Diode, Schottky, $10SC4M | 99-211005 |
| D13-D16 | Diode, Rectifier, IN4006 | 99-211008 |
Inductors
| Ll | Inductor, 15 mH | 99-211052 |
| 13 | Inductor, 7 #H (Acceptable substitute is part no. 99-21 1051) | 99-211050 |
| L4 | Inductor, 2.2 #H | 99-211054 |
| 5 | Inductor, 1.5 mH | 99-211053 |
Resistors
| R1, R2 | Resistor, Carbon Film, 180 kQ, +5%, 1 W | 99-211034 |
| R3 | Resistor, Wirewound, 1200, +5%, 2 W | 99-211019 |
| R4 | Resistor, Wirewound, 0.470, +5%,2W | 99-211018 |
| R5 | Resistor, Wirewound, 332, +5%,2W | 99-211017 |
| RG, R7 | Resistor, Carbon Film, 5.60, +5%, 4 W | 99-211027 |
| R8 | Resistor, Wirewound, 0.47 9, +5%,2W | 99-211018 |
| RO | Resistor, Carbon Film, 109, +5%, 4 W | 99-211029 |
| RIO | Resistor, Carbon Film, 1 kQ, +5%, 4 W | 99-211032 |
| Ril | Resistor, Carbon Film, 470, +5%, 4 W | 99-211025 |
| R12 | Resistor, Carbon Film, 5.60, +5%, 4 W | 99-211027 |
| R13 | Resistor, Carbon Film, 3309, 45%, 4 W | 99-211026 |
| R14 | Resistor, Carbon Fiim, 270 2, +5%, % W | 99-211023 |
| RIS | Resistor, Carbon Film, 3309, +5%, 4% W | 99-211022 |
| RIG | Resistor, Carbon Film, 8.29, +5%, % W | 99-211028 |
| R17, R18 | Resistor, Carbon Film, 569, +5%, %« W | 99-211031 |
| R19 | Resistor, Carbon Film, 399, +5%, 4 W | 99-211030 |
| R20 | Resistor, Carbon Film, 2 kQ, +5%, 4 W | 99-211035 |
| R21 | Resistor, Carbon Film, 4709, +5%, % W | 99-211024 |
| R22 | Resistor, 2.2 k@, +2%, 4% W | 99-211021 |
| R23 | Resistor, Metal Film, 2 kQ, +2%, 4 W | 99-211033 |
| R25 | Resistor, Carbon Film, 100, +5%, 4 W | 99-211029 |
| R26 | Resistor, Wirewound, 502, +5%,2W | 99-211015 |
| R27 | Resistor, Carbon Film, 472, +5%, 4 W | 99-211025 |
| R31 | Resistor, Wirewound, 1500, 45%, 2 W | 99-211016 |
Transistors
| Ql | ‘Transistor, NPN, 2SC1413A | 99-211002 |
| Q3 | ‘Transistor, NPN, PE8050B | 99-211003 |
| Q3 | Transistor, PNP, PE8550B | 99-211004 |
Miscellaneous
| FI | Fuse, 2 A, 250 V, SEMKO | 99-211058 |
| IC1 | Regulator, UA43 1AWC. | 99-211001 |
| SCRI | Thyristor, SCR | 99-211013, |
| Tl | Transformer | 99-211055 |
| TRI | Thermistor, 0.50, +5%,5 W | 99-211020 |
| VRI | Potentiometer, Trimming, 3 kQ | 99-211014 |
| ZD1 | Diode, Zener, 1N752A | 99-211007 |
Fuse, 2 A, 250 V 99-211056
Fuse Holder, 6.35 mm 99-211060 Terminal Block, 8 Ckt 99-211057 Heat Sink 99-211059 Heat Sink, 1.5 mm 99-211061
5-11
Illustrated Parts Lists Blasteroids
99-10140 Panel Assembly 75-9485 Locknut 99-10116
99-10147 Harness_ 171006-035 Coin Mechanism
75-9448 Locknut 99-10096 Fastener
99-10151 Left Coin inlet
99-10080 ; Lamp Socket , \ . ft
99-10104 99-10105 Bar
99-10042 thru 99-10045 99-101 ; 4 a ie : Coin Switch Assembly Bracket Assembly IK . Ee < é 99-10153 ae (_ | ~ . Coin Return Box _~ oom 0180 wit 99-10068 NS <I cs So Coin Chute ‘ Oo A Con outa ~ CZ in Switch NN 99-10075 thru 99-10078 ~ Switch Wires 99-10008 Retainer 75.1412S Screw
Figure 5-5 Coin Acceptors, Inc. Coin Door Assembly 171027-001 A
5-12
Ilustrated Parts Lists Blasteroids
99-10160 Coin Inlet Housing 99-10148 Lock Assembly
99-10115 Spring
99-10141 Coin Return Cover
99-10117 Coin Return Door
99-10144 Channel Clip
“— 99-15066
99-10149 Service Door % A zB oe yy 72-HA1404C Screw
99-10139 Coin Door
99-10148 Lock Assembly
72-J3A1405B Screw
038091-01 Coin Box 99-10143 Frame
En nue 66 S8OLRE SRo8S05ES SeSEo ans SEB2LLano ZeEellcas TESropeae &3 BSc8§aoy oeSesrere LESSSzL ye 250805380 Beeeceuss BSSoRgarge 2322 38253 ogo. ear a e572 ga S2SSsse£os Poses oh eR 82coxsores pEeoeears PBoe ean 25sSsns FSSACSS23 062-52155.
Figure 5-5 Coin Acceptors, Inc. Coin Door Assembly, Continued 171027-001 A
5-13
Illustrated Parts Lists Blasteroids
Coin Acceptors, Inc. Coin Door Assembly Parts List
Part No. Description
65-441C Coin Switch 70-11-47 Miniature Bayonet Lamp 72-94068 #4-40 x y-Inch Truss-Head Screw 72-HA1404C #4-40 x Vi-Inch Pan-Head Screw
72-JA1405B #4-40 x 0.31-Inch Pan-Head Screw 75-14128 #4-40 x %-Inch Pan-Head Screw 75-9948 #4-40 Locknut 99-10008 Retainer 99-10042 Coin Switch Assembly for Belgian 5 Frand U.S. 25¢ 99-10043 Coin Switch Assembly for German 1 DM, Japanese 100 Yen, Swiss 1 Fr 99-10044 Coin Switch Assembly for German 2 DM, Italian 100 L, U.S. $1.00 99-10045 Coin Switch Assembly for Australian $.20, German 5 DM, British 10 P
99-10068 Coin Return Chute
| 99-10075 | Switch Wire | (included in coin switch assembly 99-10043) |
| 99-10076 | Switch Wire | (included in coin switch assembly 99-10042) |
| 99-1007 | Switch Wire | (included in coin switch assembly 99-10044) |
| 99-10078 | Switch Wire | (included in coin switch assembly 99-10045) |
99-10080 Lamp Socket 99-10081 Key Holder 99-10096 Fastener
99-10104 Bar Retainer 99-10105 Bar 99-10115 Spring 99-10116 Plastic Coin Return Lever
99-10117 Steel Coin Return Door 99-10139 Coin Door 99-10140 Coin Door Inner-Panel Assembly 99-10141 Die-Cast Coin Return Cover
99-10143 Coin Door Frame 99-10144 Channel Clip 99-10147 Harness 99-10148 Lock Assembly
99-10149 Service Door 99-10150 Switch Cover 99-10151 Left Coin inlet 99-10152 Right Coin Inlet
99-10153 Coin Return Box 99-10154 Bracket Assembly 99-10160 1”-Wide Die-Cast Coin Inlet Housing 99-10161 25¢ Amber Side-Entry Button Assembly
99-15066 Screw for Clamp 171006-035 Metal Coin Mechanism for U.S. 25¢
5-14
Blasteroids Illustrated Parts Lists
N O T E S
5-15
5-16 118046-002 100%6-004 118046-201 p37 oe feces A ars FD
w TE s3¢057-xx19 136057-20 Hlustrated Parts Lists
ee 89 a 37534-002 137894-002 m06 5 5
oe oR &P w& 136057-¥x17 136057-¥x18 % a,
Ls74 Foo 2
te’ soe F74,
Zz ro}
& 136957-XX15 136057-XX16
Db iit 2 ® &
“(as EES Ls32 oe a o ys
01D 2N3904 aos aE 136057-XX19 136057-Xx14
isis ce 40 re oe fe i!
“2s lw CTR InUAnBEAOG000000) 328811 108 cer usara ste % & ®
13752¢-001 Ls24us Ls24s. 2 b 437552-001__vMA 136057 -Xxx04 136057-xxi0 4¢BLASTEROIDS ATARI CAMES © 67
2 scon 2 8373 Ls2us
137308-001 gays, Sa sre? : bod © % feeer — us I; 237550-001 SOS 136057-¥x11 136057-xa2
LETA Ls245 18273 Ls37y
BAg Ta eRe 7 HS 5 5 Lsa74 cE aan 7 cs
Ls257 136057-Xx24 136057-XxX22 Ls244 FL7y = 5 2105 oO ey iss? 137535-00% 136057-Xx27 136057-XX28 a ae coo ele be a,
usizs Ls253 By "42, L386 2 Ge usi7 L374 Lso¥
sos 2 a 68000 _137289-003, , & 136057-Xx26 Fa) Ea ne FO! tawa_ f 136057-Xxx25 re | 6 a gene is Ga usin on oa |
: be = o 32z8 ws0si «ah 4 Rou 7 6 =
SRLET as 8 MRDE_IN USA AD443Z6
z| Fl
U3 ($457 fo)
lal
rt
Figure 5-6 Blasteroids Game PCB Assembly A044326-21 C a) =sdas io
ae ey
® Sy PHR
Ps iN Blasteroids
Blasteroids Hustrated Parts Lists
Blasteroids Game PCB Assembly Parts List:
| Designator | Description | Part No. |
Integrated Circuits
| 1B | IC, 741890 | 37-74L890 |
| 1D | IC, 741820 | 37-741820 |
| y | IC, 7418194 A | 37-7418194 |
| IL | IC, 1M Bit Mask ROM, LH231000 | 136057-1125 |
| 24/B | IC, 2804 A-45, 450 nsec | 137329-450 |
| 2c | IC, 68000, 8 Mhz | 137289-003 |
| 2E/F | IC, 74F04 | 137437-001 |
| my | IC, 7418194 A | 37-7418194 |
| 3F | IC, SOS | 137550-001 |
| 3L | IC, 1M Bit Mask ROM, LH231000 | 136057-1126 |
| 4A | IC, 7418157 | 37-74L8157 |
| 4B | IC, EPROM, 27512-300 | 136057-2122 |
| 4c | IC, EPROM, 27512-300 | 136057-2124 |
| 4D | IC, 741886 | 37-74LS86 |
| 4E | IC, 7418174 | 37-741S174 |
| 4F | IC, 7418253 | 37-7418253 |
| 4K | IC, 7418174 | 37-7ALS174 |
| 4L | IC, 7418374 | 37-74L8374 |
| 4M | IC, 741804 | 37-741804 |
| sD | Ic, 7418244 | 37-74LS244 |
| SE | IC, 7418257 | 37-74LS257 |
| SF | IC, 7418253 | 37-741S253 |
| SL | IC, 6264-10, 100 nsec | 137535-004 |
| 5M | IC, 1M Bit Mask ROM, LH231000 | 136057-1127 |
| 6/7L | IC, 6264-10, 100 nsec | 137535-004 |
| 6B | IC, EPROM, 27512-300 | 136057-2121 |
| 6c | IC, EPROM, 27512-300 | 136057-2123 |
| 6D | IC, 7418244 | 37-7418244 |
| OE | IC, 7418257 | 37-7418257 |
| OF | IC, 74F174 | 137531-001 |
| Ic | IC, 7418245 | 37-741S245 |
| 7D | IC, 7418273 | 37-7418273, |
| 7E | IC, 7418374 | 37-7ALS374 |
| TE | IC, 7418174 | 37-741S174 |
| 8A | IC, Leta | 137304-1001 |
| 8B | IC, 7418245 | 37-7418245 |
| 8C | IC, 741814 | 37-741814 |
| 8D | IC, 7418373 | 37-741S373 |
| 8E | IC, 7418244 | 37-7418244 |
| 8K | IC, Vmatch | 137552-001 |
| 8M | IC, EPROM, 27512-250 | 136057-1109 |
| 8N | IC, EPROM, 27512-250 | 136057-1110 |
| 9A | IC, SCOM | 137526-001 |
| 9B, 9C | IC, 7418245 | 37-741S245 |
Mlustrated Parts Lists Blasteroids
Blasteroids Game PCB Assembly Parts List, Continued
| Designator | Description | Part No. | |
| 10A | IC, 7418257 | 37-7418257 | |
| 10B | IC, 7418139 | 37-741S139 | |
| 10C | IC, 7418138 | 137177-001 | |
| 10D | IC, 7418373 | 37-741S373 | |
| 10E | IC, 7418244 | . | 37-741S244 |
| 10F | IC, 7418139 | 37-7418139 | |
| 10K | IC, SOS | 137550-001 | |
| 10M | IC, EPROM, 27512-250 | 136057-1111 | |
| 10N | IC, EPROM, 27512-250 | 136057-1112 | |
| 1B | IC, 74700 | 137327-001 | |
| 1c | IC, 741811 | 137149-001 | |
| 11D | IC, 741874 | 37-TALS74 | |
| ME | IC, 741832 | 37-741832 | |
| 1y | IC, 741802 | 37-7ALSO2 | |
| ML | IC, 741832 | 37-741532 | |
| 11M | IC, EPROM, 27512-250 | 136057-1113 | |
| 11N | IC, EPROM, 27512-250 | 136057-1114 | |
| 12B | IC, 741832 | 37-741832 | |
| 12¢ | IC, 7415163 A | 37-741S163A | |
| 12D | IC, 74°32 | 137486-001 | |
| 12E | IC, 74F10 | 137428-001 | |
| 12F | IC, 74F00 | 137327-001 | |
| 12y | IC, 7418244 | 37-741S244 | |
| 12L | IC, 74F244 | 137502-001 | |
| 13B | IC, 741532 | 37-741832 | |
| 13 | IC, 741874 | 37-741S74 | |
| 13D | IC, 741810 | 37-741S10 | |
| 13E | IC, 741874 | 37-741S74 | |
| 13), 13L | AC, 74F163 | 137345-001 | |
| 13M | IC, EPROM, 27512-250 | 136057-1115 | |
| 13N | IC, EPROM, 27512-250 | 136057-1116 | |
| 14/15B | IC, 741874 | 37-741S74 | |
| 14/15C | IC, 74F00 | 137327-001 | |
| 14/15M | IC, EPROM, 27512-250 | 136057-1117 | |
| 14/15N | IC, EPROM, 27512-250 | 136057-1118 | |
| 4B | Ic, 741808 | 37-74LS08 | |
| 14C | IC, 74°74 | 137436-001 | |
| 14D | Ic, 741800 | 37-74LS00 | |
| 14E | IC, 74F174 | 137531-001 | |
| 14F | IC, RAM, 2KX8, 35 nsec | 137534-001 | |
| 14y | IC, 74F163 | 137345-001 | |
| 14K | IC, RAM, 2KX8, 35 nsec (Acceptable substitutes are partnos. | —137534-001 |
137533-002, 137534-201, and 137534-301.)
| 14. | IC, 74F163 | 137345-001 |
| 15/16B, 15/16C | IC, RAM, 2KX8, 45 nsec (Acceptable substitutes are part nos. | 137534-002 |
137533-001, 137534-202, and 137534-302.)
| 15A | IC, 7406 | 37-7406 |
| 15D | IC, 7418244 | 37-7418244 |
5-18
Blasteroids Illustrated Parts Lists
Blasteroids Game PCB Assembly Parts List, Continued
| Designator | Description | Part No. |
| 15E | IC, 74F158 | 137326-001 |
| 15J, 15L | IC, 74F163 | 137345-001 |
| 16/17B, 16/17C | IC, 74HC273 | 137556-001 |
| 164, | IC, 7418260 | 137332-001 |
| 16D | IC, 74F374 | 137420-001 |
| 16E | IC, 74F158 | 137326-001 |
| 16) | IC, 74F21 | 137555-001 |
| 16M | IC, EPROM, 27512-250 | 136057-1119 |
| 16N | IC, EPROM, 27512-250 | 136057-1120 |
| 17A | IC, 7418260 | 137332-001 |
| 17D | IC, 74F374 | 137420-001 |
| IE | IC, 27LS00 A (Acceptable substitute is part no. 137175-002 ) | 137170-003 |
| 17J | IC, 74F398 | 137557-001 |
Capacitors
| C2 | Capacitor, .1 pF, 50 V, Ceramic | 122002-104 |
| C3-C6 | Capacitor, 100 pF, 100 V, Ceramic | 122016-101 |
| C7-C10 | Capacitor, .01 pF, 50 V, Ceramic | 122002-103 |
| C11-C18 | Capacitor, .1 pF, 50 V, Ceramic | 122002-104 |
| C19-C21 | Capacitor, 100 pF, 100 V, Ceramic | 122016-101 |
| C22-C24 | Capacitor, .001 pF, 50 V, Ceramic | 122002-102 |
| C26 | Capacitor, 47 pF, 25 V, Electrolytic | 24-250476 |
| C27 | Capacitor, .1 pF, 50 V, Ceramic | 122002-104 |
| C28 | Capacitor, 39 pF, 100 V, Mica | 128002-390 |
| C29 | Capacitor, 100 pF, 100 V, Mica | 128002-101 |
| C30 | Capacitor, .1 pF, 50 V, Ceramic | 122002-104 |
| C31 | Capacitor, 47 pF, 25 V, Electrolytic | 24-250476 |
| €33-C91 | Capacitor, .1 pF, 50 V, Ceramic | 122002-104 |
Inductor
| 14 | Inductor, 100 pH | 41-3003 |
Transistors
| Q1-04 | ‘Transistor, 2N3904 | 34-2N3904 |
| Qs | Transistor, 2N5306 | 133033-001 |
| 6 | Transistor, 2N3904 | 34-2N3904 |
Resistors
| RI | Resistor, 1 K , +5%, 1/8 W | 110027-102 |
| R2-R5 | Resistor, 470 , +5%, 1/8 W | 110027-471 |
| R6-R9 | Resistor, 1 K , £5%, 1/8 W | 110027-102 |
| R10-R13 | Resistor, 3.3 K , 5%, 1/8 W | 110027-332 |
| R14-R24 | Resistor, 470 , +5%, 1/8 W | 110027-471 |
| R25-R32 | Resistor, 1 K , +5%, 1/8 W | 110027-102 |
| R33 | Resistor, 2.4 K , 5%, 1/8 W | 110027-242 |
| R34 | Resistor, 68 , +5%, 1/4 W | 110000-680 |
| R35 | Resistor, 1.5 K , 5%, 1/8 W | 110027-152 |
| R36 | Resistor, 10 , +5%, 1/8 W | 110027-100 |
Illustrated Parts Lists Blasteroids
Blasteroids Game PCB Assembly Parts List, Continued
| Designator | Description | Part No. |
| R37 | Resistor, 2.4 K , +5%, 1/8 W | 110027-242 |
| R38 | Resistor, 68 +5%, 1/4 W | 110000-680 |
| R39 | Resistor, 1.5 K , 5%, 1/8 W | 110027-152 |
| R40 | Resistor, 10 , +5%, 1/8 W | 110027-100 |
| R41 | Resistor, 2.4 K , +5%, 1/8 W | 110027-242 |
| R42 | Resistor, 68 , +5%, 1/4 W | 110000-680 |
| RB | Resistor, 1.5 K , +5%, 1/8 W | 110027-152 |
| R44 | Resistor, 10 , +5%, 1/8 W | 110027-100 |
| R45 | Resistor, 1 K , +5%, 1/8 W | 110027-102 |
| R46 | Resistor, 10 K , +5%, 1/8 W | 110027-103 |
| R47 | Resistor, 1 K , #5%, 1/8 W | 110027-102 |
| R48 | Resistor, 100 K , +5%, 1/8 W | 110027-104 |
| RAD | Resistor, 240 , +5%, 1/8 W | 110027-241 |
| R50 | Resistor, 1 K , +5%, 1/8 W | 110027-102 |
| R51, R52 | Resistor, 10 K , +5%, 1/8 W | 110027-103 |
| R53. | Resistor, 390 , +5%, 1/8 W | 110027-391 |
| R54-R58, R63-R71 | Resistor, 1 K , 5%, 1/8 W | 110027-102 |
| R72 | Resistor, 47, +5%, 1/8 W | 110027-470 |
| R73. | Resistor, 1 K , +5%, 1/8 W | 110027-102 |
| R74 | Resistor, 47 , +5%, 1/8 W | 110027-470 |
| R75 | Resistor, 1 K , +5%, 1/8 W | 110027-102 |
| R76 | Resistor, 47 , £5%, 1/8 W | 110027-470 |
| R77 | Resistor, 1 K , +5%, 1/8 W | 110027-102 |
Connectors
| AUD | Conn, 11 Ckt, Hdr, .100 Ctr, Key 5 | 179118-011 |
| CTRA | Conn, 11 Ckt, Hdr, .100 Cu, Key 2 | 179118-011 |
| LET | Conn, 11 Ckt, Hdr, .100 Ctr, Key 4 | 179118-011 |
| VID | Conn, 11 Ckt, Hdr, .100 Ctr, Key 3 | 179118-011 |
| PWR | Conn, 6 Ckt, Hdr, .250 Ctr | 179069-006 |
Sockets Socket, 20 Pin 79-42C20 Socket, 24 Pin 79-42C24 Socket, 28 Pin 79-42C28 Socket, 40 Pin 79-42C40 Socket, 64 Pin 79-42C64
Miscellaneous
| CRI | Diode, Light Emitting, Type MV5053 | 38-MV5053 |
| GND1-RES3 | Test Point | 179051-001 |
| RN1-RN3. | Resistor Network, R/2R | 118016-001 |
| RES | Test Point | 179051-001 |
| XL | Crystal, 14.318 | 144000-004 |
5-20
Blasteroids Illustrated Parts Lists
N O T E S
Illustrated Parts Lists
5-22 Blasteroids
J2 J3 C15 + 22,35V —[[er2 |- [cRBt 1N5401
IN5401
Q1 Q2
TDA2030 TDA2030
Figure 5-7 Housequake PCB Assembly A045050-01 A
Blasteroids Illustrated Parts Lists
Housequake PCB Assembly Parts List
| Designator | Description | Part No. |
Capactors
| C1-C4 | Capacitor, 3300 pF, 25 V, Electrolytic | 123003-338 |
| C7, C8 | Capacitor, .22 pF, 50 V, Ceramic | 122015-224 |
| C9-C12 | Capacitor, .1 pF, 50 V, Ceramic | 122002-104 |
| C13, C14 | Capacitor, .22 pF, 50 V, Ceramic | 122015-224 |
| C15, C16 | Capacitor, 22 pF, 35 V | 24-350226 |
| C17 | Capacitor, .0068 pF, 50 V, Ceramic | 122015-682 |
Diodes
| CR1-CR4 | Diode, 1N5401 | 31-1N5401 |
| CR5-CR8 | Diode, 1N4001 | 31-1N4001 |
Integrated Circuit
| Q1, Q2 | IC, TDA2030 | 137301-001 |
Resistors
| R1, R2 | Resistor, 22 K , 5%, 1/4 W | 110000-223 |
| R3-R5 | Resistor, 10 K , 25%, 1/4 W | 110000-103 |
| RO | Resistor, 1K , +5%, 1/4 W | 110000-102 |
| R7, R8 | Resistor, 1, +5%, 1/4 W | 110000-010 |
| RO | Resistor, 1 K , +5%, 1/4 W | 110000-102 |
| R10 | Resistor, 910 , 5%, 1/4 W | 110000-911 |
Connectors
| yi | Connector, 2 Circuit, Header, 0.156-Inch Ctr | 179213-002 |
| j2 | Connector, 3 Circuit, Header, 0.156-Inch Ctr | 179213-003 |
Miscellaneous Heat Sink, TDA2030 178190-032
| ICL | Nut/Washer Assembly, #6-32 | 75-99516 |
| Ic | Pan Head Screw, #6-32 | 72-1606S |
Nut/Washer Assembly, #6-32 75-99516
Pan Head Screw, #6-32 72-16068
| 1C1,2 | Thermal Compound | 78-16001 |
| c1-4 | Hot Melt Adhesive | 106006-001 |
5-23
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
Blasteroids
Stand-Alone Audio PCB Assembly Illustrated Parts Lists
Parts List
| Designator | Description | Part No. |
Integrated Circuits
| 1J-CPU | Integrated Circuit, 6502A | 90-6013 |
| 1M-SCOM | Integrated Circuit, SCOM | 137526-001 |
| 2B | Integrated Circuit, LM324 | 37-LM324 |
| 2D | Integrated Circuit, YM3012 | 137402-001 |
| 2F-YAM | Integrated Circuit, YM2151 | 137401-001 |
| 2H-RAM | Integrated Circuit, 6264-15, 150 ns | 137441-002 |
| 2K-ROM | Integrated Circuit, 27512, 300 ns | 136057-1135 |
| 2L-PAL | Integrated Circuit, Programmed PALI6L8A, 25 ns | 136056-2101 |
| 3F | Integrated Circuit, 7415374 | 37-74LS374 |
| 4A, 4B | Integrated Circuit, LM324 | 37-LM324 |
| 4M | Integrated Circuit, 74LS138 | 137177-001 |
| 5C, 5D | Integrated Circuit, 4066B | 37-4066 |
| 5K SH | Integrated Circuit, 74LS273 | 37-74L8273 |
| 5) | Integrated Circuit, 74L5240 | 137251-001 |
| 5K | Integrated Circuit, 74LS74 | 37-74L874 |
| g | Integrated Circuit, 7418393 | 37-74L8393 |
| ALTCLK | Integrated Circuit, 7415393 | 37-74LS393 |
| QI, Q2 | Integrated Circuit, TDA2030 | 137301-001 |
| Q4 | Integrated Circuit, 7905, Standup | 37-7905 |
Capacitors
| cl | Capacitor, .22 pF, 50 V, Ceramic | 122015-224 |
| c2 | Capacitor, 22 uF, 35 V, Electrolytic | 24-350226 |
| Cc | Capacitor, .22 wF, 50 V, Ceramic | 122015-224 |
| C4 | Capacitor, .1 wE, 50 V, Ceramic | 122002-104 |
| cs | Capacitor, 22 uF, 35 V, Electrolytic | 24-350226 |
| C6-C9 | Capacitor, .1 wE, 50 V, Ceramic | 122002-104 |
| cl2 | Capacitor, .1 #E 50 V, Ceramic | 122002-104 |
| C€13-C16 | Capacitor, 100 pF, 100 V, Ceramic | 122016-101 |
| C17 | Capacitor, .1 ¢F, 50 V, Ceramic | 122002-104 |
| C18-C21 | Capacitor, 3300 pF, 25 V, Electrolytic, Radial | 123003-338 |
| C23 | Capacitor, .1 pF, 50 V, Ceramic | 122002-104 |
| C24 | Capacitor, 10 uF, 25 V, Electrolytic | 24-250106 |
| C25 | Capacitor, .22 ¢F, 50 V, Ceramic | 122015-224 |
| C26 | Capacitor, .1 pF, 50 V, Ceramic | 122002-104 |
| C27 | Capacitor, 10 uF, 25 V, Electrolytic | 24-250106 |
| C28 | Capacitor, .1 uF, 50 V, Ceramic | 122002-104 |
| c29 | Capacitor, .22 uF, 50 V, Ceramic | 122015-224 |
| c30 | Capacitor, .1 uF, 50 V, Ceramic | 122002-104 |
| C31 | Capacitor, 10 pF, 25 V, Electrolytic | 24-250106 |
| 32, C33 | Capacitor, .001 nF, 50 V, Ceramic | 122002-102 |
| C34, C35 | Capacitor, .1 wE 50 V, Ceramic | 122002-104 |
| C38 | Capacitor, .1 wF, 50 V, Ceramic | 122002-104 |
| C41, C42 | Capacitor, .1 uF, 50 V, Ceramic | 122002-104 |
| C43 | Capacitor, 10 pF, 25 V, Electrolytic | 24-250106 |
5-25
Illustrated Parts Lists
Stand-Alone Audio PCB Assembly Blasteroids
Parts List
| Designator | Description | Part No. |
| C48-C52 | Capacitor, .1 uF, 50 V. Ceramic | 122002-104 |
| C53 | Capacitor, 0022 uF, 50 V, Axial Ceramic | 122015-222 |
| C54 | Capacitor, .0027 nF 50 V, Ceramic | 122015-272 |
| C55 | Capacitor, .001 4, 50 V, Ceramic | 122002-102 |
| C56 | Capacitor, .0027 aE, 50 V, Ceramic | 122015-272 |
| C57 | Capacitor, .001 wR, 50 V, Ceramic | 122002-102 |
| C58 | Capacitor, .0022 uF, 50 V, Axial Ceramic | 122015-222 |
| C61-C68 | Capacitor, .1 xE, 50 V, Ceramic | 122002-104 |
| C69 | Capacitor, 39 p¥, 100 V, Ceramic | 122016-390 |
| C70 | Capacitor, 100 pF, 100 V, Ceramic | 122016-101 |
| C71-C74 | Capacitor, .1 uF, 50 V, Ceramic | 122002-104 |
| C84 | Capacitor, .1 pF, 50 V, Ceramic | 122002-104 |
Diodes
| CRI, CR2 | Diode, 1N4001 | 31-1N4001 |
| CR3 | Diode, MV5053, Light Emitting | 38-MV5053 |
| CR4, CRS | Diode, 1N4001 | 31-iN4001 |
| CRO | Diode, MV5053, Light Emitting | 38-MV5053 |
| CR7-CR1O | Diode, 1N5401 | 31-1N5401 |
| CR13 | Diode, MV5053, Light Emitting. | 38-MV5053 |
| CRIA, CRI5 | Diode, 1N4001 | 31-1N4001 |
Inductor
| Ll | Inductor, 100 pH | 41-3003 |
Resistors
| RL | Resistor, 1 kQ, +5%, 4 W | 110000-102 |
| R2 | Resistor, 10kQ, =5%, 4 W | 110000-103 |
| R3, R4 | Resistor, 12, +5%, 4 W | 110000-010 |
| RS | Resistor, 1 kQ, +5%, 4% W | 110000-102 |
| RG | Resistor, 10 kQ, +5%, % W | 110000-103 |
| R10 | Resistor, 0.2, 6 W | 110005-001 |
| RIL | Resistor, 1 kQ, 45%, 4 W | 110000-102 |
| R12 | Resistor, 4709, £5%, 4 W | 110000-471 |
| R13 | Resistor, 1kQ, 45%, 4 W | 110000-102 |
| R14 | Resistor, 470 2, +5%, 4 W | 110000-471 |
| RI5 | Resistor, 1 kQ, +5%, 4 W | 110000-102 |
| RIG | Resistor, 470 Q, +5%, 4 W | 110000-471 |
| R17, R18 | Resistor, 10 kQ, + 5%, 4 W | 110000-103 |
| RIO | Resistor, 22 k®, +5%, 4 W | 110000-223 |
| R20 | Resistor, 1 kQ, +5%, 14 W | 110000-102 |
| R21 | Resistor, 22 kQ, +5%, 4 W | 110000-223 |
| R22 | Resistor, 100, +5%, 4 W | 119000-100 |
| R23 | Resistor, 560 2, +5%, 4 W | 110000-561 |
| R24 | Resistor, 1k, +5%, 4 W | 110009-102 |
| R26, R27 | Resistor, 102, +5%, 4 W | 110000-100. |
| R28 | Resistor, 10k, +5%, 4 W | 110000-103 |
| R29 | Resistor, 1 k@, +5%, “ W | 110000-102 |
| R33, R34 | Resistor, 470 2, +5%, 44 W | 110900-471 |
| R35 | Resistor, 75 kQ, +5%, 4 W | 110000-753 |
| R36, R37 | Resistor, 10k®, +5%, 4 W | 110000-103 |
| R38. | Resistor, 47 kQ, +5%, 4 W | 110000-473 |
| R43-R48 | Resistor, 12 kQ, +5%, 4 W | 110000-123 |
| R49 | Resistor, 10 kQ, +5%, 4 W | 110000-103 |
5-26
Blasteroids Illustrated Parts Lists
Stand-Alone Audio PCB Assembly Parts List
| Designator | Description | Part No. |
| R50 | Resistor, 1 k®, +5%, 4 W | 110000-102 |
| RSI | Resistor, 10 kQ, +5%, 4 W | 110000-103 |
| R52 | Resistor, 10 k2, 45%, 4 W | 4110000-103 |
| R53, R54 | Resistor, 1 kQ, +5%, 4 W | 110000-102 |
| R55, R56 | Resistor, 150 kQ, 45%, 4 W | 110000-154 |
| R58 | Resistor, 1 kQ, +5%, 4 W | 110000-102 |
| R59 | Resistor, 150 kQ, +5%, % W | 110000-154 |
| ROO | Resistor, 1 k9, +5%, 4 W | 110000-102 |
| RO1 | Resistor Pot, 10 kQ, Horizontat, Dual | 119011-103 |
| R62 | Resistor, 7.5 kQ, +5%, 4 W | 110000-752 |
| R63 | Resistor, 30 kQ, +5%, 4 W | 110000-303 |
| R64 | Resistor, 15 kQ, +5%, 4 W | 110000-153 |
| R65, ROG | Resistor, 12 kQ, +5%, 4 W | 110000-123 |
| R67 | Resistor, 15 kQ, +5%, 4 W | 110000-153 |
| ROB | Resistor, 30 kQ, +5%, 4 W | 110000-303 |
| ROO | Resistor, 7.5 kQ, +5%, 4 W | 110000-752 |
| R74-R81 | Resistor, 1 k®, +5%, 4 W | 110000-102 |
| R82 | Resistor, 4709, +5%, 4 W | 110000-471 |
| R83 | Resistor, 150 kQ, +5%, 4 W | 110000-154 |
| R84 | Resistor, 02, % W | 110005-001 |
| R85A | Resistor, 4700, +5%, 4 W | 110000-471 |
| R86 | Resistor, 2200, 45%, 4 W | 110000-221 |
| R103, | Resistor, 150k, +5%, 4 W | 110000-154 |
Transistors
| 5-98 | Transistor, 2N3904 | 34-2N3904 |
| Q9, Q10 | Transistor, 2N5306 | 133033-001 |
Connectors
| JACDC | Connector, 12 Ckt., Header, .156-Inch Ctr., Key 11 | 179213-012 |
| JCDL | Connector, 2 Ckt., Header, .156-Inch Ctr. | 179213-002 |
| JCOIN | Connector, 6 Ckt., Header, .100-Inch Ctr, Key 2 | 179118-006 |
| JSCOM | Connector, 11 Ckt., Header, .100-Inch Ctr., Key 5 | 179118-011 |
| JSPK | Connector, 6 Ckt., Header, .156-Inch Ctr, Key 3 | 1792 13-006 |
Sockets
| 1J-CPU | Socket, Medium-Insertion-Force IC, 40-Contact | 79-42C40 |
| 2D | Socket, Medium-Insertion-Force IC, 16-Contact | 79-42C16 |
| 2F-YAM | Socket, Medium-Insertion-Force IC, 24-Contact | 79-42C24 |
| 2H-RAM | Socket, Medium-Insertion-Force IC, 28-Contact | 79-42C28 |
| 2K-ROM | Socket, Medium-Insertion-Force IC, 28-Contact | 79-42C28 |
Miscellaneous
| HSL | Heat Sink, TDA2030 | 178190-032 |
| Ql | Nut/Washer Assy, #6-32 | 75-99516 |
| Ql | Screw, Pan-Head, Cross-Recessed, #6-32 x %-Inch | 72-1606S |
| Ql, Q2 | Compound, Thermal | 78-16001 |
| sw | Switch, Self-Test, Slide, SPDT | 69-004 |
Adhesive, Hot Melt 106006-001 Test Point 179051-001
5-27
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
Blasteroids
Date:
Coin Information and Game Statistics Left Coins Number of coins deposited in the ieft coin mechanism.
| Right Coins | —_____ | Number of coins deposited in the right coin mechanism. |
New Games Number of new games started. Continuation Number of times players continued their games.
| 0 Mins | ——___ | Minutes of idle time. |
| 1 Mins | —_____ | Minutes played as a one-person game. |
2 Mins Minutes played as a two-person game. Red Mins Minutes played on the red side. Green Mins Minutes played on the green side. Sessions Total number of games played. Error Count EEROM errors detected.
| Total Coins | _—___——s | Number of coins deposited in both coin mechanisms. |
Avg Time/Coin Average game time per coin, in seconds.
New Game Times Histogram Information Easy Level Medium Level Hard Level
| Length | Number | Length | Number | Length | Number |
| in Seconds | of Games | in Seconds _ of Games | in Seconds | of Games | |
| 0-39 | —___ | 0-39 | _—__ | 0-39 | |
| 40-59 | —__ | 40-59 | —___ | 40-59 | |
| 60-79 | 60-79 | 60-79 | |||
| 80-99 | —___ | 80-99 | —___ | 80-99 | |
| 100-119 | 100-119 | 100-119 | |||
| 120-139 | 120-139 | 120-139 | |||
| 140-159 | —__ | 140-159 | —__ | 140-159 | |
| 160-179 | 160-179 | 160-179 | |||
| 180-199 | —_— | 180-199 | 180-199 | ||
| 200-219 | — | 200-219 | 200-219 | ||
| 220-239 | — | 220-239 | 220-239 | ||
| 240-259 | — | 240-259 | - | 240-259 | |
| 260-279 | 260-279 | -_ | 260-279 | ||
| 280-299 | 280-299 | 280-299 | |||
| 300-319 | — | 300-319 | — | 300-319 | |
| 320-339 | —___ | 320-339 | —_— | 320-339 | |
| 340-359 | —___ | 340-359 | —_ | 340-359 | |
| 360-379 | | | 360-379 | —_ | 360-379 | |
| 380-399 | a | 380-399 | —__ | 380-399 | |
| 400 & up | 400 & up | 400 & up |
Continuation Times Histogram Information
| Easy Level | Medium Level | Hard Level |
Length Number Length Number Length Number in Seconds of Games in Seconds _ of Games in Seconds of Games 0-39 a 0-39 _ 0-39 40-59 — 40-59 ee 40-59 60-79 —___ 60-79 —__ 60-79
| 80-99 —_— | 80-99 _ | 80-99 |
| 100-119 | 100-119 | 100-119 |
120-139 120-139 —___ 120-139 140-159 140-159 ——— 140-159
| 160-179 | 160-179 | 160-179 |
| 180-199 | 180-199 | 180-199 |
| 200-219 | 200-219 | 200-219 |
| 220-239 | 220-239 | 220-239 |
| 240-259 | 240-259 | 240-259 |
| 260-279 | 260-279 | 260-279 |
| 280-299 | 280-299 | 280-299 |
300-319 —__ 300-319 —_—__ 300-319 320-339 —___ 320-339 —_—_ 320-339 340-359 —_ 340-359 —____ 340-359 360-379 — 360-379 —__—_—. 360-379 380-399 —__ 380-399 — 380-399
| 400 & up | 400 & up | 400 & up |
Session Time in Minutes Length Number Length Number Length Number in Seconds of Games inSeconds _ of Games in Seconds of Games
| 0-9 | 40-44 | 75-79 |
| 10-14 | 44-49 | 80-84 |
| 15-19 | 50-54 _ | 85-89 |
| 20-24 | 55-59 | 90-94 |
| 25-29 | 60-64 | 95-99 |
30-34 —_ 65-69 _ 100 & up 35-39 —_ 70-74
AC Alternating current; from zero it rises to a maximum positive level, then passes through zero again to a maximum negative level.
ACTIVE STATE The true state of a signal. For example: The active state for is low. ADDRESS A value that identifies a specific location of data in memory; normally expressed in hexadecimal notation. ANALOG Measurable in an absolute quantity (as opposed to on or off), Analog devices are volume controls, light dimmers, stereo amplifiers, etc. ANODE The positive (arrow) end of a diode. AMPLIFIER A device used to increase the strength of an applied signal. AMPLITUDE The maximum instantaneous value of a waveform pulse from zero, ASTABLE Having no normal state. An astable device will free-run or oscillate as long as operating voltage is applied. The oscillation frequency is usually controlled by external circuitry. AUXILIARY COIN SWITCH A momentary-contact pushbutton switch with a black cap located on the utility panel. The auxiliary coin switch adds credits to the game without activating a coin counter. BEZEL A cut, formed, or machined retention device, such as the conical device used to mount a pushbutton switch to a control panel, or the formed device used to frame the video display screen. BIDIRECTIONAL Able to send or receive data on the same line (e.g., the data bus of a microprocessor). BINARY A number system that expresses all values by using two digits (0 and 1). BIT A binary digit; expressed as 1 or 0. BLANKING Turning off the beam on a cathode-ray tube during retrace. BLOCK DIAGRAM A drawing in which functional circuitry units are represented by blocks. Very useful during initial troubleshooting. BUFFER
- An isolating circuit designed to eliminate the reaction of a driven circuit on the circuits driving it (e.g., a buffer amplifier).
- A device used to supply additional drive capability. BUS An electrical path over which information is transferred from any of several sources to any of several destinations.
CAPACITOR A device capable of storing electrical energy. A capacitor blocks the flow of DC current while allowing AC current to pass. CATHODE The negative end of a diode. CHIP An integrated circuit comprising many circuits on a single wafer slice. CLOCK A repetitive timing signal for synchronizing system functions. COINCIDENCE Occurring at the same time. COIN COUNTER A 6-digit electromechanical device that counts the coins inserted in the coin mechanism(s). COIN MECHANISM A device on the inside of the coin door that inspects the coin to determine if the correct coin has been inserted.
COMPLEMENTARY Having opposite states, such as the outputs of a flip-flop. COMPOSITE SYNC Horizontal and vertical synchronization pulses that are bused together into a single signal. This signal provides the timing necessary to keep the display in synchronization with the game circuitry.
Glossary
COMPOSITE VIDEO Complete video signal from the game system to drive the display circuitry, usually comprising H SYNC, V SYNC, and the video,
CREDIT One play for one person based on the game switch settings. cRT Cathode-ray tube. DATA General term for the numbers, letters, and symbols that serve as input for device processing. DARLINGTON A two-transistor amplifier that provides extremely high gain. DC Direct current, meaning current flowing in one direction and of a fixed value.
DEFLECTION YOKE Electromagnetic coils around the neck of a cathode-ray tube. One set of coils deflects the electron beam horizontally and the other set deflects the beam vertically. DIAGNOSTICS A programmed routine for checking circuitry. For example: the self-test is a diagnostic routine. DIODE A semiconductor device that conducts in only one direction. DISCRETE Non-integrated components, such as resistors, capacitors, and transistors. DMA Direct memory access. DMA is a process of accessing memory that bypasses the microprocessor logic. DMA is normally used for transferring data between the input/output ports and memory. DOWN TIME The period during which a game is malfunctioning or not operating correctly due to machine failure. EAROM Electrically alterable read-only memory (see ROM). The EAROM is a memory that can be changed by the application of high voltage.
gl-1
FLYBACK A step-up transformer used in a display to provide the high voltage. GATE
- A circuit with one output that responds only when a certain combinaton of pulses is present at the inputs.
- A circuit in which one signai switches another signal on and off.
- To control the passage of a pulse or signal. HARNESS A prefabricated assembly of insulated wires and terminals ready to be attached to a piece of equipment. HEXADECIMAL A number system using the equivalent of the decimal number 16 as a base. The symbols 0,-9 and A.-F are usually used.
IMPLODE To burst inward; the inward collapse of a vacuum tube. vo Input/Output. IRQ Interrupt request. IRQ is a control signal to the microprocessor that is generated by external logic. This signal tells the microprocessor that external logic needs attention. Depending on the program, the processor may or may not respond. LED The abbreviation for a light-emitting diode.
LOCKOUT COIL Directs coins into the coin return box when there is no power to the game. LOGIC STATE The binary (1 or 0) value at the nade of a logic element or integrated circuit during a particular time. Also called the logic level. The list below shows the voltage levels corresponding to the logic states (levels) in a TTL system. Logtc 0, Low = 0 VDC to +0.8 VDC Grey Area (Tri-State Level) = +0.8 VDC to +2.4 VDC Logic 1, High = +2.4 VDC to +5VDC MULTIPLEXER A device that takes several low-speed inputs and combines them into one highspeed data stream for simultaneous transmission on a single line. NMI Non-maskable interrupt. NMI is a request for service by the microprocessor from external logic. The microprocessor cannot ignore this interrupt request. PAGE A subsection of memory. A read-only memory device (see ROM) is broken into discrete blocks of data. These blocks are called pages. Each block has X number of bytes. PCB The abbreviation for a printed-circuit board. PHOTOTRANSISTOR A transistor that is activated by an external light source. POTENTIOMETER 1, A resistor that has a continuously moving contact which is generally mounted on 2 moving shaft. Used chiefly asa voltage divider. Also called a pot (slang).
- An instrument for measuring a voltage by balancing it against a known voltage. RAM Random-access memory. A device for the temporary storage of data.
RASTER-SCAN DISPLAY A display system whereby images are displayed by continuously scanning the cathoderay tube horizontally and vertically with an electron beam. The display system controls the intensity of the electron beam. RETRACE In a raster-scan display, retrace is the time during which the cathode-ray tube electron beam is resetting either from right to left or from bottom to top. RESISTOR, A device designed to have a definite amount of resistance. Used in circuits to limit current flow or to provide a voltage drop. ROM Read-only memory, A device for the permanent storage of data. SIGNATURE ANALYSIS A process of isolating digital logic faults at the component level by means of special test equipment called signature analyzers. Basically, signature analyzers & a sma, (e.g., the ATARI® CAT Box) convert lengthy bit streams into four-digit hexadecimal signatures. The signature read by the analyzer at each circuit node is then compared with the known good signature for that node. This process continues until a fault is located. TROUBLESHOOT The process of locating and repairing a fault.
VECTOR A line segment drawn between specific X and Y coordinates on a cathode-ray tube. WATCHDOG A counter circuit 7 designed to
7 protect the
*y microprocessor
from self-destruction if a program malfunction occurs, If a malfunction does occur, the counter applies continuous pulses to the reset line of the microprocessor, which causes the microprocessor to keep resetting, X-Y DISPLAY A display system whereby images are displayed with veciors. ZENER DIODE A special diode used as a regulator. Its main characteristic is breaking down at a specified reverse-bias (Zener) voltage.
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
Seller warrants that its printed-circuit boards and parts thereon are free from defects in material and workmanship under normal use and service for a period of ninety (90) days from date of shipment. Seller warrants that its video displays and. laser-video disc players (in games supplied with displays and video-disc players) are free from defects in material and workmanship under normal use and service for a period of thirty (30) days from date of shipment. None of the Seller's other products or parts thereof are warranted. If the products described in this manual fail to conform to this warranty, Seller's sole liability shall be, at its option, to repair, replace, or credit Buyer's account for such products which are returned to Seller during said warranty period, provided:
- Seller is promptly notified in writing upon discovery by Buyer that said products are defective;
- Such products are returned prepaid to Seller's plant; and (©) Seller's examination of said products discloses to Seller’s satisfaction that such alleged defects existed and were not caused by accident, misuse, neglect, alteration, improper repair, installation, or improper testing. In no event shall Seller be liable for Joss of profits, loss of use, incidental or consequential damages. Except for any express warranty set forth in a written contract between Seller and Buyer which contract supersedes the terms herein, this warranty is expressed in lieu of all other warranties expressed or implied, including the implied warranties of merchantability and fitness for a particular purpose, and of all other obligations or liabilities on the Seller's part, and it neither assumes nor authorizes any other person to assume for the Seller any other liabilities in connection with the sale of products by Seller.
The use of any non-Atari paris may void your warranty, according to the terms of the warranty. The use of any non-Atari parts may also adversely affect the safety of your game and cause injury to you and others. Be very cautious in using non-Atari-supplied components with our games, in order to ensure your safety. Atari distributors are independent, being privately owned and operated. In their judgment they may sell parts or accessories other than Atari parts or accessories. Atari Games Corporation cannot be responsible for the quality, suitability or safety of any non-Atari part or any modification including labor which is performed by such distributor.
Atari Games Corporation 675 Sycamore Drive P.O, Box 361110 _ Milpitas, California 95035.