CATHODE RAY TOMES

Star Wars TM-225 1st Printing

Star Wars (set 1) (Atari, 1983) · Technical Manual · 94 pages · 86 sections · original scan

Page 1

TM-225 1st printing

©1983 Lucastilm Ltd & Atari, Inc. Ail rights reserved. “Trademarks of Lucasfilm Ltd. used by Atari, Inc. under license

Page 2

If reading through this manual does not lead to solving a certain maintenance problem, call TELEHELP® at the Atari Customer Service office in your geographical area, as shown below.

WEST and CENTRAL U.S.A. Parts and Service

Atari, Inc. California Customer Service Office 1105 N, Fair Oaks Avenue P. O. Box 427, Sunnyvale, CA 94086 Telex 17-1103 (Monday-Friday, 7:30-4:00 pm Pacific Time) = From California, Alaska, or Hawaii (408) 745-2900 = Service from anywhere in the area shown in white toll-free (800) 538-1611

EAST U.S.A. Service only

Atari, Inc. New Jersey Customer Service Office 12A World's Fair Drive, Somerset, NJ 08873 Telex 37-9347 (Monday-Friday, 7:30-4:00 pm Eastern time) = From New Jersey (201) 469-5993 = From anywhere else in this area toll-free (800) 526-3849

EUROPE Parts and Service

Atari Ireland Limited European Customer Service Office Tipperary Town, Ireland Telex 28-165 TIPPERARY TOWN, (Monday-Friday, 9:00-6:00 pm GMT) IRELAND BS 062-52155

Page 3

STAR. WARS:

Operators Manual

with Illustrated Parts Lists

©1983 Lucasfilm Ltd. & Atari, Inc, All rights reserved. “Trademarks of Lucasfilm Ltd. used by Atari, Inc. under license.

Page 4

Star Wars

No part of this publication may be reproduced by any mechanical, photographic, or electronic process, or in the form of a phonographic recording, nor may it be stored ina retrieval system, transmitted, or otherwise copied for public or private use, without permission from the publisher. The game play, all graphic designs, this technical manual, its accompanying schematic diagrams, and the display manual are protected by the U.S. Copyright Act of 1976. This Act provides for increased penalties for violating federal copyright laws. Courts can impound infringing articles while legal action is pending. If infringers are convicted, courts can order destruction of the infringing articles. In addition, the Act provides for payment of statutory damages of up to $250,000 in certain cases. Infringers may also have to pay costs and attorneys’ fees and face an imprisonment of up to five years. Atari will aggressively enforce its copyrights against any infringers. We will use all legal means to immediately halt any manufacture, distribution, or operation of a copy of unauthorized video games. Anyone who purchases such illegal copies risks forfeiting such a game.

Published by: ATARI, INC. 790 Sycamore Drive PO. Box 906 Milpitas, California 95035

Printed inthe U.S.A. 6M

Page 5

Star Wars

Notice Regarding Non-ATARI Parts

Use of non-ATARI parts or modifications of any ATARI® game circuitry may adversely affect the safety of your game, and may cause injury to you and your players.

You may void the game warranty (printed on the inside back cover of this manual) if you do any of the following: © Substitute non-ATARI parts in the game. © Modify or alter any circuits in the game by using kits or parts not supplied by Atari.

NOTE

This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual, may cause interference to radio communications. Jt has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of Federal Communications Commission (FCC) Rules, which are designed to provide reasonable protection against such interference when operated. ina commercial environment. Operation of this equipment ina residential area or modification to this equipment is likely to cause interference in which case the user, at his own expense, will be required to take whatever measures may be required to correct the interference. If you suspect interference from an ATARI® game at your location, check the following: © All green ground wires in the game are properly connected as shown in the game wiring diagram. ° The power cord is properly plugged into a grounded three-wire outlet. © The game printed-circuit boards (PCB) are properly installed within the Electromagnetic Interference (EMI) cage. © The EMI Shield PCB is properly installed and connected in series with the game PCB harness. © All filter capacitors required on the EMI Shield PCB are properly soldered in place. If youare still unable to solve the interference problem, please contact ATARI Customer Service. See the inside front cover of this manual for service in your area.

iii

Page 6

Star Wars

Table of Contents

Set Up How to Use This Manual 11 Game Overview ........ : . 7 : ; : 13 Installation Specifications 13 Inspecting the Game . . 13 Voltage-Plug Selection an 1-4 Flight Control Calibration . 15 Switch Locations....... 15 Selecting the Game Options . 16 Game Play... . 1-8 Attract Mode . . 18 Selecting-a-Death Star Mode . 1-9 Play Mode . . 110 High-Score Mode . 11 Self-Test Mode HI

Self Test SelPTest Displays: . 60. gop ca et ee ewes ta cee ee ee pe ns te eae 2-2

Troubleshooting Troubleshooting Aids «0.6... 0.6.2 o eee eee 3-2 Troubleshooting Techniques... 6.0.66. 3-2

Maintenance Cleaning Requirements 42 Opening the Control Panel 42 Flight Control Maintenance 43 Removing the CRT Assembly ... 4-8 Wiring the Utility Panel Controls 49

Illustrated Parts Lists Cabinet-Mounted Assemblies, US-Built Cabinet 2 5-2 Cabinet-Mounted Assemblies, Ireland-Built Cabinet . 5-6 Star Wars Decals, US-Built Cabinet . Flight Control Assembly . . Fluorescent Tube and Speaker Assembly . Utility Panel Assembly ........... Vertically Mounted Coin-Door . American-Made Coin-Door . Power Supply Assembly .. . PCB Mounting Hardware, US-Built Cabinet PCB Mounting Hardware, Ireland-Built Cabinet . . . EMI Shield PCB Assembly ........ Regulator/Audio Il PCB Assembly . Main PCB Assembly ............ Analog Vector-Generator (AVG) PCB Assembly . oe Sound PCB Assembly... 000.0 cece cc cece eect eee eter teen eee e ens

Glossary

Page 7

Star Wars

vi

Safety Summary

The following safety precautions apply to all game operatorsand service personnel. Specific warnings and cautions will be found throughout this manual where they apply.

A wWaRNincs A Properly Ground the Game. Players may receive an electrical shock if this game is not properly grounded! To avoid electrical shock, do not plug in the game until it has been inspected and properly grounded. This game should only be plugged into a grounded 3-wire outlet. Ifyou have only a 2-wire outlet, we recommend you hire a licensed electrician to install a grounded outlet. Players may receive an electrical shock if the control panel is not properly grounded! After servicing any parts on the panel, check that the grounding clip is firmly secured to the metal tab on the inside of the control panel. Only then should you lock up the game. AC Power Connection. Before connecting the game to the AC power source, verify that the proper voltage-selection plug is installed on the game's power supply. Disconnect Power During Repairs. To avoid electrical shock, disconnect the game from the AC power source before removing or repairing any part of the game. When removing or repairing the video display, extra precautions must be taken to avoid electical shock because high voltages may exist within the display circuitry and cathode-ray tube (CRT) even after power has been disconnected. Do not touch internal parts of the display with your hands or metal objects! Always discharge the high voltage from the CRT before servicing this area of the game. To discharge the CRT: Attach one end of a large, well-insulated, 20-kV jumper to ground. Momentarily touch the free end of the grounded jumper to the anode by sliding it under the anode cap. Wait two minutes and discharge the anode again. Use Only ATARI Parts. To maintain the safety integrity of your ATARI game, do not use non- ATARI parts when repairing the game. Use of non-ATARI parts or other modifications to the game circuitry may adversely affect the safety of your game, and injure you or your players. Handle Fluorescent Tube and CRT With Care. If you drop a fluorescent tube or CRT and it breaks, it may implode! Shattered glass can fly six feet or more from the implosion. Use the Proper Fuses. To avoid electrical shock, use replacement fuses which are specified in the parts list for this game. Replacement fuses must match those replaced in fuse type, voltage rating, and current rating. In addition, the fuse cover must be in piace during game operation.

CAUTION

Properly Attach All Connectors. Make sure that the connectors on each printed-circuit board (PCB) are properly plugged in. Note that they are keyed to fit only one way. If they do notslip on easily, do not force them. A reversed connector may damage your game and void the warranty.

Page 8

Set-Up Procedures

How to Use This Manual

This manual, written for game operators and sevice technicians, describes your new ATARI game. Chapter 1 contains a game overview, game specifications, inspection procedures, voltage plug and fuse information, switch locations, and option information. Chapter 2 contains self-test procedures. Chapter 3 contains troubleshooting procedures. Chapter 4 contains maintenance and repair procedures. Chapter 5 contains illustrated parts lists. Notes in this chapter refer you to other places in the manual for more detailed information. Schematic diagrams of the game circuitry are included as asupplement to this manual.

WARNING Shock Hazard To avoid electrical shock, do not plug in the game until it has been inspected and properly set up for the line voltage in your area. Donot touch internal parts of the display with your hands or metal objects!

Chapter 1

Page 9

SetUp’ Star Wars

Fluorescent Tube & Speaker See Figure 5-4 Game Identification Label x

Toe ee

Access Panel

| Detlection PCB ‘Used with Atari Display See Display Manual Flight Control Assembly, See Figure 5-3 EMI Cage Ses Figure 5-9 Control Panel 7 C Inside EMI Cage: Main PCB* Utility Panel Assy. See Figure 5-12 See Figure 5-5 ANG PCB x See Figure 5-13 Sound PCB x

High-Voltage PCB *: See Figure 5-14

Used with Atari Display See Display Manual

EMI Shield PCB See Figures 5-9 & 5-41 Regulator/Audio II PCB x: See Figures 5-9 & 5-10

Power Supply * See Figure 58 Power On/Off Switch

WARNING

Shock Hazard

Do not plug in the game until it has. been inspected. This game shoula only be connected to a grounded ‘S-wire outlet, Ifyou have only a2-wire outlet, we recommend you hire a licensed electrician to install a grounded outlet. Players may receive an electrical shock if this game is not properly grounded! Coin Door Assy. See Figures 5-6 or 5-7

x Item with a serial number label

Figure 1-1 Game Overview

Page 10

Star Wars

Game Overview

STAR WARS* is a spectacular video spectacle! STAR WARS iS a one-player game, which uses a color XY video display. As the player, you’ll enter the exciting world of LUKE SKYWALKER* and pilot the RED 5 X-WING" spacecraft to victory over the Empire’s evil forces!

New Features Voice-enhanced game play. The voices you will recognize belong to the actual characters of LUKE SKYWALKER, DARTH VADER*, BEN KENOBI", HANSOLO*, and R2-D2*. They intensify the excitement of swift and dynamic game play. Flight control. The flight control for STAR WaRS is anew Atari design. It allows a player to use real flying techniques on a voyage that is out of this world! ‘Tamper-proof screws. There are 12 tamper-proof screws on the cover of the flight control assembly. They prevent abuse of the control or its handles. Flight-control wrench.A special wrench for the tamperproof screws is included with your game. It is located in the coin box. Medium-speed, medium-resolution, cathode-ray tube. This new XY cathode-ray tube (CRT) produces exceptionally clear graphics for the world of LUKE SKYWALKER.

Options display. The Self-Test program Of STAR WARS includes an options display that enables you to select game options without having to set the option switches from the back of the cabinet. See Chapter 2 for more details.

All major parts of the STAR wars Cabinet are illustrated in Figure 1-1.

Installation Specifications

Table 1-1 describes the physical, electrical, and environmental specifications of the game.

Table 1-1 Installation Requirements

Characteristic Requirement

250 W Nominal 0° to +38° C(+32° to +100° F) Power Consumption ‘Temperature Humidity Not to exceed 95% relative Line Voltage 100 to 240 VAC Width 64.1 cm (25.25 in.) Depth 83.2 cm (32.75 in.) Height 182.9 cm (72 in.)

*© 1983 Lucasfilm Lid. & Atari, Inc. All rights reserved. Lucasfilm trademarks used under license. Set-Up

Inspecting the Game

Please inspect your game carefully to ensure that it was delivered to you in good condition. 1, Examine the exterior of the game cabinet for dents, chips, or broken parts.

  • Remove the screws from the reat access panel. Unlock and open this panel and the coin door. Inspect the interior of the game as follows: a. Ensure that all plug-in connectors (on the game harnesses) are firmly plugged in. Replug any connectors found unplugged. Do not force connectors together. The connectors are keyed so they only fit in the proper orientation. A reversed edge connector may damage a printed-circuit board (PCB) and will void your warranty. b. Ensure that all plug-in integrated circuits on each PCB are firmly plugged into their sockets. c, Remove the tie-wrap that secures the coiled power cord inside the cabinet. Inspect the power cord for any cuts or dents in the insulation. Repair or replace it as required. Place the square strain-relief plate in the wood slot at the bottom of the rear panel opening. d, Inspect the power supply. Make sure the fuse block cover is mounted in place. Check that the green ground wire is connected. e. Inspect other major subassemblies, such as the control panel, video display, EMI cage, and each PCB. Make sure they are mounted securely and that the green ground wires are connected.
Page 11

set-Up

Voltage-Plug Selection

and Fuses

The power supply in your game contains six fuses. When you replace a fuse, use the identical type fuse with the same electrical rating (see Figure 1-2). This power supply operates on the line voltage of many countries. The power supply comes with either one, two, or three voltage-selection plugs. Plug voltages and wire

4A, 250V

FUSE F3 20A,32V

FUSES F4-F6 4A, 250V Star Wars

colors are 100 VAC (violet wire color), 120 VAC (yellow wire color), 220 VAC (blue wire color), and 240 VAC (brown wire color). See Figure 1-2 for placement of the voltage-selection plug. Before plugging in your game, check your line voltage. Next, check the wire color on the voltage-selection plug. Make sure the voltage-selection plug is correct for the line voltage of your location. Now plug the game into a grounded 3-wire outlet.

VOLTAGE-SELECTION PLUGS

7A, 250V

v3,

Fuse cover is shown in Figure 5-8

Figure 1-2 Voltage-Selection Plug and Fuse Locations

Page 12

Star Wars

Flight Control Calibration

The STAR WARS game hasa self-calibrating flight control. The game circuitry monitors the position of the cursor on the display in relation to the flight control vertical and horizontal position. Calibration is quickly accomplished by moving the cursor to all four extreme edges of the display. Calibrating is also accomplished during normal game play, but may take a few seconds to optimize.

Switch Locations

Power On/Off Switch

The power on/off switch is located on the back of the cabinet on the lower left side (see Figure 1-1).

Utility Panel Switches The volume control, coin counter(s), self-test switch, and auxiliary coin switch are on the utility panel. The utility panel is located inside the upper coin door (see Figure 1-1).

Coin

Counter Volume

Control

utility

Panes Self-Test

‘Switch Sound Board Set-Up

The volume control adjusts the level of sound produced by the game. The coin counter(s) records the number of coins entered into the game. The self-test switch initiates the self-test mode. The auxiliary coin switch credits the game without activating a coin counter. See Figures 1-3 and 5-5 for details of these switches.

Option Switches STAR WARS has three option switches, These switches are dual-inline package (DIP) switches located on the Main PCB. The Main PCB is set in the electromagnetic interference (EMI) cage (see Figure 5-9.) Figure 1-3 shows the location of these switches on the Main PCB: © The option switch at 10D is for selecting play options. © The option switch at 10E/F is for selecting coin and credit options.

  • The option switch at IIL is for selecting special options.

Auxiliary Coin Switch

Game PCB

Interconnect Board “oO at { OFF c os dQ

sor a1

ot

Figure 1-3 Switch Locations

Page 13

Set-Up

Selecting the Game Options

Settings for option switches are listed in Tables 1-2, 1-3, and 1-4. Options preset at the factory are shown by the “4 symbol; however, you may change the settings according to your needs.

To verify other option selections, check the self-test display that appears when you turn on the game. Then, verify the option-switch settings on the self-test display as described in Chapter 2.

Important: The Self-Test program of STAR WARS includes an options display that enables you to select game options without having to set the option switches from the back of the cabinet. See Chapter 2 for more details. Star Wars

Table 1-2 lists settings for the DIP switch at 10D. This switch is used to select play options (such as the number of siarting shields per game). Table 1-3 lists settings for the DIP switch at 10E/F. This switch is used to select coin and credit options available for the left and right coin mechanisms. Tabie 1-4 lists settings for the DIP switch at IIL. This switch is used to select a special option for the way coin outputs are handled by the game. The basic unit of measurement is a coin worth $.25 or 1 DM. Thus, if you have a 2 DM/1 DM coin door with two coin counters, set switch 1 at location 11L to OFF, Then, different denominations are counted on the two coin counters,

Table 1-2 Switch Settings for Play Options

Settings of 8-Toggle Switch on Star Wars Game PCB (at 10D) 1 2 3 4 6 8 Option

On On

Off On Off Off

On Off

On On

On Off

On On

Off = On

On Off

On Off 6 Starting Shields 7 Starting Shields 8 Starting Shields 9 Starting Shields

Easy game play Moderate game play~4 Hard game play Hardest game play

0 Bonus Shields for Destroying Death Star 1 Bonus Shield for Destroying Death Star 2 Bonus Shields for Destroying Death Star 3 Bonus Shields for Destroying Death Sur

Music in the Attract Mode<t No Music in the Attract Mode

On Freeze Mode Off Normal Game Play Mode~¢

“4 Manufacturer's recommended settings

1-6

Page 14

Star Wars Set-Up

Table 1-3 Switch Settings for Coin and Credit Options

Settings of 8-Toggle Switch on Star Wars Game PCB (at 10E/F)

1235678Option
OnOnFree Play

Off On 2 Credits Off Off Ya Credit

.OnOff1 Credit<4

Left Coin Mechanism On 1 Coin<d Off 2 Coins Right Coin Mechanism

OnOn1Coin<t
Offon4 Coins

On Off 5 Coins

Off Off 6 Coins

Bonus Coin Adder

OnOnOn0 Bonus Coins Added<@
OffOnOn1 Bonus Coin Added for 2 Coins
OnOffOn1 Bonus Coin Added for 4 Coins
OffOffOn2 Bonus Coins Added for 4 Coins
OnOnOff1 Bonus Coin Added for 5 Coins
OffOnOff1 Bonus Coin Added for 3 Coins
OnOffOff0 Bonus Coins Added
OffOffOff0 Bonus Coins Added

Table 1-4 Switch Settings for Special Options

Settings of 4Toggle Switch on Star Wars Game PCB (at 111)

123Option

On Z ra FA Outputs of coin counter driver 1 and 2 tied together

5ae(for 1 counter) <4
OffgggOutputs of coin counter driver 1 and 2 separate (for 2

a counters)

4 Manufacturer's recommended settings

Page 15

Set-Up

Game Play

STAR WARS is aone-player game witha color X-Y video display. You command LUKE SKY WALKER's RED 5-X:WING spacecraft with Atari’s new flight control. Your main goal is to blow up the DEATH STAR’. To do this, you must reach the thermal exhaust port at the end of the DEATH STAR trench, and fire a proton torpedo into it. You must survive three phases of play to reach the exhaust port. The first phase of play will engage you ina spectacular battle in space—a war in the stars! TWIN-ION ENGINE (T.LE.) FIGHTERS* from the DEATH STAR attack you. DARTH VADER’s Ship appears in this phase—menacing and powerful! Your goal in this phase is to shoot the T.LE. FIGHTERS and their shots.

The second phase of play takes the x-wING down to the surface of the DEATH STAR which is covered with laser bunkers and laser towers. You must avoid collision with these objects and their shots to keep the number of Deflector Shields above zero, Extra bonus points are earned for exploding all laser tower tops. The third phase of play takes RED 5 down into the DEATH STAR trench. The walls are lined with red laser-gun turrets that fire at you as you approach. You must counter these shots by avoiding them or by shooting them. Trench catwalks also appeai, in varied shapes and altitudes. You must avoid hitting the catwalks, or else your number of deflector shields will decrease.

If you survive the flight down the trench, a message and. voice will alert you that the exhaust port is straight ahead. You must shoot the exhaust port to explode the DEATH STAR. If you miss the exhaust port, you will plough through the wall at the end of the trench and lose one deflector shield. If you succeed in blowing up the DEATH STAR, RED 5 soars away from the DEATH STAR and then turns to view the tremendous explosion. Select-a-Death Star bonus and Remaining Shield Energy bonus are now scored. Depending on the settings of the option switches (see Tables i-2, 1-3, and 1-4), additional deflector shields will be awarded. A new DEATH STAR then comes into view. The EMPIRE* is really mad now, and the powers in the EMPIRE want to launch LUKE and the RED 5 into eternity! STAR Wars has five possible modes of operation: Attract, Select-a-Death Star, Play, High Score, and Self-Test.

  • ©1983 Lucasfilm Lid. & Atari, Inc. All rights reserved. Lucasfilm trademarks used under license. Star Wars

Attract Mode

The Attract Mode begins when power is applied to the game; or when the Play, High-Score, or Self-Test Modes end. The Attract Mode ends either when a credit is entered and the game goes into Select-a-Death Star Mode, or when the self-test switch is turned on. The first screen displayed in the Attract Mode is the Banner Screen. The STAR WARS logo appears with a background of moving stars and then flies away to infinity. As it vanishes, the introductory story line moves into position from the bottom of the screen. The text pauses for about 20 seconds and then, one line at a time, quickly recedes into the distance.

Banner Screen Text:

OBI-WAN KENOBIIS GONE BUT HIS

PRESENCE IS FELT WITHIN THE FORCE. THE EMPIRE'S DEATH STAR UNDER THE COMMAND OF DARTH VADER NEARS THE REBEL PLANET. YOU MUST JOIN THE REBELLION TO STOP THE EMPIRE. THE FORCE WILL BE WITH YOU. ALWAYS.

The next screen in the Attract Mode is the Flight Instruction Screen. it outlines REDS’s weaponry, defense system, and mission. The text appears one line ata time, pauses for about 20 seconds, then fades away. Flight Instruction Screen FLIGHT INSTRUCTIONS TO RED FIVE

  • YOUR X-WING IS EQUIPPED WITH AN INVISIBLE DEFLECTOR SHIELD THAT WILL PROTECT YOU FOR x** COLLISIONS.
  • DEFLECTOR STRENGTH IS LOST WHEN A FIREBALL IMPACTS YOUR SHIELD OR WHEN YOU STRIKE A LASER TOWER OR TRENCH CATWALK. 3, AIM YOUR LASERS WITH CURSOR TO EXPLODE EM- PIRE TIE FIGHTERS, LASER TOWER TOPS AND TRENCH TURRETS. 4, SHOOT FIREBALLS BEFORE THEY IMPACT YOUR SHIELD.
  • THE REBEL FORCE IS DEPENDING ON YOU TO STOP THE EMPIRE BY BLOWING UP THE DEATH STAR. The top part of the Banner Screen should display the last score achieved and the wave number. The messages JN- SERT COIN(S) and X COINS PER PLAY should alternately flash if no credit is in the game. If the game has credits, then the message X CREDITS and PULL FIRE TRIGGER TO START will be displayed. These messages appear on all screens, The third screen in the Attract Mode is the Scoring Screen. It lists targets in the game and their point values. This screen scrolls up from the bottom of the screen then fades away.
  • * Replace x with 6, 7, 8, or 9, depending on option switch settings.
Page 16

Star Wars

Scoring Screen SCORING TIE FIGHTERS 1,000 DARTH VADER SHIP 2,000 LASER BUNKERS 200 LASER TOWERS 200 TRENCH TURRETS 100

FIREBALLS 33

EXHAUST PORT 25,000 DESTROYING ALL TOWER TOPS 50,000 The fourth screen in the Atiract Mode is the High-Score Screen. It displays a table containing the ten highest scores. At the bottom of the screen the copyright message appears. (The High-Score Screen shown here contains the default entries that will appear if no high scores are in the game’s memory, The game will retain and display the top three scores entered into its memory even if the power is turned off and then on again. Set-Up

High-Score Screen PRINCESS LEIA'S REBEL FORCE

1.OBI1285353
2.WAN1110936
3.HAN1024650
4.GJR872551
5.MLH813553
6.JED704899
7.NIA518000
8.EJD492159
9.EAR384766
10.RLM380655

STAR WARS © 1983 LUCASFILM LTD. AND ATARI, INC. ALL RIGHTS RESERVED LUCASFILM TRADEMARKS USED UNDER LICENSE.

You may bring the High-Score Screen or the Flight Instruction Screen into view at any time during the Attract Mode. Moving the flight control to the right displays the High- Score Screen and moving it to the left displays the Flight intruction Screen.

Select-a-Death Star Mode

The Select-a-Death Star Mode begins when the correct credit(s) is entered anda fire trigger is pulled. You will hear the voice of LUKE saying, “RED 5 standing by,” and you'll have 8 seconds to select one of 3 starting DEATH STARS. A. DEATH STAR is selected by first maneuvering the flight control until the cursor on the screen is positioned on the desired DEATH STAR and then by pulling the Laser Fire Trigger. The DEATH STARS are labeled easy, medium, and bard on the display. The Easy DEATH STAR awards no bonus for completion of the starting level as indicated by NO BONUS. The Medium DEATH STAR awards 400,000 points and the Hard DEATH STAR awards 800,000 points. Failure to select alevel within the countdown time automatically starts the Play Mode at the Easy level (wave one).

1-9

Page 17

Set-Up

Play Mode

STAR WARS game play is enhanced by 13 special sound effects and by actual character voices communicating with the player. Voices: LUKE: RED 5 standing by. LUKE: R2, try and increase the power. LUKE: This is RED 5, I’m going in. LUKE: I’m hit but not bad, R2 see what you can do with it. LUKE: T’ve lost R2. LUKE: Ican't shake him! DARTH: I’m on the leader. DARTH: The FORCE is strong with this one. DARTH: Ihave you now! DARTH: Stay in attack formation. BEN: Use the FORCE, LUKE. BEN: Remember, the FORCE will be with you, always. BEN: LUKE, trust me. BEN: Let go, LUKE. HAN: Yahoo! You’re all clear, kid. HAN: Great shot kid! That was one in a million. WEDGE*: Look at the size of that thing! R2: ‘Yes. R2: No. R2: lagree. R2: Sequence completion. R2: Ouch! R2: That really hurt. The Play Mode begins in outer space with the DEATH STAR Off in the distance. The RED 5 X-WING aiming device (cursor) appears as a crosshair on the screen. As the flight control is moved in any direction, the four laser guns move accordingly. Firing the laser guns will cause alternating laser beams to fire from the guns toward the cursor. In this mode, R2-D2 is controlling the flight pattern of the X:WING based on the flight of attacking T.1.E. FIGHTERS.

Your goal is to blast any and all TE. FIGHTERS and their oncoming shots. If you are hit, your deflector shield will automatically turn on and dissipate the energy from the shot, causing a very bright light to flash on the screen. You will experience a roll in space due to the impact. In a while, the T.LE. FIGHTERS Will turn away from you and fly back to the DEATH STAR.

*© 1983 Lucasfilm Ltd. & Atari, Inc. All rights reserved. Lucasfilm trademarks used under license.

1-10 Star Wars

In the next phase of the Play Mode, the x:wiNG flies directly toward the DEATH STAR, engines roaring, to a surface covered with hostile laser bunkers and laser towers. Now you, not R2-D2, control the X-WING. Your goal in this phase is to reach the trench. To do this you must avoid or eliminate (by shooting) the structures and the shots fired by them. The laser tower tops have a progressive scoring incentive that is displayed in a message in the top center of the screen, along with the number of remaining laser tower tops to be destroyed before the x-wING dips into the trench, Eliminating all laser tower tops awards you an added bonus. Getting hit by a shot or smashing into a laser tower top or laser bunker will roll the X-WING to the right or left as the deflector shield automatically turns on and absorbs impact, displaying a very bright screen. Each collision costs you one deflector shield.

Once you have traveled the required distance over the DEATH STAR Surface, the x-WING dips down into the long, deadly trench. In this phase, you can fly right, left, up, or down; but you remain within the trench. Your main goal while in the trench is to destroy the DEATH STAR by shooting the exhaust port at the end of the trench. You can survive the trench by flying around catwalks, which stretch across the trench at various altitudes, and by avoiding or shooting shots fired from the red laser-gun turrets on the walls. Deflector shield energy is lost ifa shot hits you or if you smash into a catwalk. If you successfully reach and shoot the exhaust port, the RED 5 X-WING will soar away from the DEATH STAR and then turn toward it to watch it biow up. If you miss the exhaust port, you will crash through the back wall and R2-D2 will show his displeasure with you. The X-WING will remain in the trench until the DEATH STAR is destroyed or you run out of deflector shields. Upon destroying the DEATH sTaR, the X-WING returns to another war in the stars with smarter T.L.E. FIGHTERS from a more advanced DEATH STAR. Your ability as a JEDI Warrior’ will be challenged even more with the destruction of each successive DEATH STAR.

Page 18

Star Wars

Hints for Game Play © Develop skill for controlling the X:WING with the flight control. It’s like flying a plane. © Blast all the laser tower tops with your laser guns for additional bonus points. © STAR WaRs is a pattern game, so learn the easy levels, and then select a more difficult level. ® The game requires almost constant laser fire during higher levels. The game ends when you get hit and the deflector shield level is zero. The words GAME OVER appear ina very large size as your ship vanishes from the screen.

High-Score Mode

This mode begins with lively music if your score is one of the ten highest scores earned since the game was turned on. A screen appears with the message: MESSAGE FROM REBEL COMMAND POST YOU ARE A TRUE REBEL PILOT THE FORCE IS WITH YOU SHOOT YOUR INITIALS Initials surround the high-score table in the middie of the screen, You have 30 seconds to shoot (enter) your initials. The top 3 scores will be saved even with the power off, but the entire high-score table can be reset to its default scores when in the Self-Test Mode. setUp

Self-Test Mode

Self-Test is divided into two sections. The first section shows game statistics and allows the operator to reset certain statistics or change options with the use of the flight control. The second section is designed to allow checking of game switches, hardware failures, potentiometer adjustments, and video display adjustments. Self-Test may be entered any time during the Attract Mode. See Chapter 2 for details.

Vl

Page 19

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 20

Self-Test Procedure

This game will test itself and provide data to show that the game circuitry and controls are operating properly. Selftest data is presented visually on the video display and audibly through the speakers. No additional equipment is required. We suggest you perform a self-test when you first set up, each time you collect money, change the game options, or suspect game failure.

Chapter 2

Page 21

Self-Test

Self-Test Displays

Fourteen self-test displays provide a visual check of the game statistics, options, switch settings, mathbox circuitry, display circuitry, and the condition of the read-only memory (ROM) and random-access memory (RAM). The first self-test display (Size and Centering) is obtained while in the Attract Mode. When the self-test switch is turned on during the Attract Mode, the game enters the Self-Test Mode. Turning the self-test switch off at any time during the Self-Test Mode causes the game to return to the Attract Mode,

NOTE Before selecting the Self-Test Mode, perform the following size and centering check with the game in the Attract Mode. The remaining self-test displays are obtained while the game is in the Self-Test Mode.

Size and Centering Display

While the game is in the Attract Mode, verify that a small blue dot is displayed within 44-inch of the edge in each corner of the screen. If the blue dots are not in the proper position, refer to the X/Y size and centering adjustment procedures included on the Analog Vector-Generator schematic diagrams.

NOTE The following self-test displays are arranged in the sequence in which they occur after the selftest switch is set to the on position. Press the auxiliary coin switch to end each display and obtain the next display. If the self-test procedures are not performed in sequence, pressing the auxiliary coin switch will advance through the displays until the desired display is obtained. After the last display has ended, the sequence starts over with the Switch Test display. To start with the Accounting and Game Times display, the self-test switch must first be turned off and then on again.

Accounting and Game Times Display Select the Self-Test Mode by pushing the self-test switch to the up position. The Accounting and Game Times display will appear as shown in Figure 2-1. The totals on this display are those accumulated since the accounting and game times information was last reset. (Refer to Game Options Display for the reset procedure.) The coin accounting information, which is the first four statistics in the Accounting Information section of the display, cannot be reset. They are accumulated from the date the game was manufactured, or since the non-volatile random-access memory (NOVRAM) last failed or was replaced.

2-2 Star Wars

ACCOUNTING INFORMATION

To PERCENTAGE OF FLAY HISTORY OF GAME TIMES

Figure 2-1 Accounting and Game Times Display AUXILIARY COINS displays the number of free credits selected by the auxiliary coin switch in the normal play mode. LEFT MECH COINS displays the number of coins inserted into the left coin mechanism.

RIGHT MECH COINS displays the number of coins inserted into the right coin mechanism. TOTAL COINS PAID displays the total number of coins inserted into both game coin mechanisms.

NOTE The following accounting and time information is accumulated since the game was manufactured (or last reset). Refer to Game Options Display for the reset procedure.

GAMES PLAYED displays the total number of free and paid games played and highest wave achieved. TOTAL GAME TIME displays the total time, in seconds, of all the games played. AVERAGE GAME TIME displays the average time, in minutes and seconds, of all the games played. TOTAL TIME ON displays the total time, in seconds, the game has been on. PERCENTAGE OF PLAY displays the percentage of time the game has been in Play Mode (as opposed to Attract Mode). HISTORY OF GAME TIMES displays the number of games played that were within each of 18 game-time increments (0 to six minutes in 20- second increments).

Page 22

Star Wars

Game Options Display

Press the auxiliary coin switch to obtain the Game Options display as shown in Figure 2-2. Use this display to view or change game option settings; reset high scores; reset ac-

countingandgametimeinformation;ortestthe

NOVRAM.

BONUS SHIELD

MUSICINATTRACT
RESETHIGHSCORES

RESET TIMING INFD RESET OPTIONS TEST NoOvRen NENG ERARAS

PULL RIGHTFIRETO PERFORM RESETS

uP, DOWN TO SELECT ITEM

PULLLEFTPERETOCHANGESETTING

PRESS AUX COIN FOR SELF TEST

Figure 2-2 Game Options Display The first section of the Game Options display shows the option settings that have been selected by either the option switches on the Main printed-circuit board (PCB) or by the flight control. The second section of the Game Options display shows the reset and NOVRAM test operations that are selectable with the flight control. Press the auxiliary coin switch to end this display. Changing the Game Options. Any of the options displayed in the first section of the Game Options display can be changed without setting the option switches on the Main PCB. Select the option to be changed by moving the flight control up or down. Press the left-hand fire trigger to cycle through the available options as indicated in the right-hand column; stop on the desired option setting. The changed option is immediately stored in the NOVRAM and is unaffected by turning off the power or the self-test switch. The options can also be changed to those selected by the option switches located on the Main PCB (see Chapter 1). If the self-test circuitry malfunctions or the option settings cannot be maintained by the software, the game will default to the hardware switch settings on the Main PCB (refer to Resetting the Options for more details). Resetting the High Scores. The top ten scores and player initials are displayed in the high-score table during the Attract Mode. All high scores can be reset using the Game Options display. Select RESET HIGH SCORES by moving the flight control up or down. Press the left-hand fire trigger and note that YES appears in the right-hand column. Then press the right-hand fire trigger to perform the reset operation, which is completed when NO appears in the righthand column. Self-Test

Resetting the Timing Information. The games played and the timing information in the Accounting and Game Times display (see Figure 2-1) can be reset using the Game Options display. Select RESET TIMING INFO by moving the flight control up or down. Press the left-hand fire trigger and

note that YES appears in the right-hand column. Then press the right-hand fire trigger to perform the reset operation, which is completed when NO appears in the righthand column. Resetting the Options. The option settings shown on the Game Options display (see Figure 2-1) can be reset (defaulted) to those selected by the option switches located on the Main PCB, Select RESET OPTIONS by moving the flight control up or down. Press the left-hand fire trigger and note that YES appears in the right-hand column, Then press the righthand fire trigger to perform the reset operation, which is completed when NO appears in the right-hand column. Testing the NOVRAM. The NOVRAM can be tested using the Game Options display. Select 7ES7 NOVRAM by moving the flight control up or down. Press the left-hand trigger and check that NO ERRORS appears in the right-hand column, If the NOVRAM is defective, a message ERROR AT and. a hexadecimal number will appear, which indicates that the NOVRAM should be replaced. Testing the NOVRAM should only be performed if a defective part is suspected because each test decreases the life of the NOVRAM.

2-3

Page 23

Self-Test

Hardware Errors Display Press the auxiliary coin switch and wait about seven seconds to obtain the Hardware Errors display as shown in Figure 2-3. This display shows the condition of the game RAM and ROM. If no hardware errors exist, the message NO ERRORS DETECTED will be displayed. If there is a RAM or ROM failure, the display will identify the failed component and give its location (see Figure 2-4).

NO ERRORS DETECTED

PRESS @UX COIN TO CONTINUE

Figure 2-3, Hardware Errors

Display—Test Passes

Figure 2-4 Hardware Errors

Display—Test Fails

Switch Test Display

Press the auxiliary coin switch to obtain the Switch Test display as shown in Figure 2-5. Perform the following procedure to verify that the game switches are operating properly.

2-4 nN Star Wars

Oneat a time, press the fire triggers and thumb pushbuttons. Note that a message appears on the display that indicates which switch was pressed. Actuate the right and left coin mechanisms and note that a message appears that indicates which coin mechanism was actuated. Position the flight control to form a single dot in the center of the smallest box in the POT TEST portion of the display. Carefully release the flight control and note that the dot remains centered within the smallest box. Ifa line forms that extends outside the frame of the smallest box, the flight control potentiometers may be misaligned. Refer to the flight control reassembly procedures in Chapter 4 for potentiometer alignment information. Tilt the flight control handles forward and backward;

note that a line forms from the center of the smallest box and moves out and back in relation to the handle position. Tilt the handles to the extreme forwardand backward position; note that the line extends past the frame of the box with open corners but not beyond the frame of the largest box. Turn the flight control fully clockwise and counterclockwise with the handles at the extreme forward then backward positions. Note that the line travels over a full 360° while not extending outside the area between the largest box and the box with the open corners. Verify that the option settings for the switches at location 10D and 10E/F shown at the bottom center of the display match those selected on the corresponding option switches (F = off, N=on).

COIN

1op FFENFNNE IGEF _NENNNNNN FRESE AUX COIN TO CONTINUE

Figure 2-5 Switch Test Display

Page 24

Star Wars

Mathbox Tests Display

Press the auxiliary coin switch to obtain the Mathbox Tests display as shown in Figures 2-6 and 2-7. The first test verifies that the MATHBOX READY signal is operating normally, If it is not, the message BAD MATHBOX READY LINE appears and no further mathbox tests are performed. If the MATHBOX READY signal is correct, then the divider and matrix circuitry should be tested. If no problems exist in the divider or matrix circuitry, the messages NO DIVIDER ERRORS and NO MATRIX ERRORS ate displayed. If divider errors exist, the message DIVIDER ERRORS will appear and each error will be indicated with an optionswitch setting for the corresponding diagnostic. Also, the numbers used on the test with the expected answer and the incorrect answer received will be displayed for each test in error.

NO DIVIDER ERRORS

Figure 2-6 Mathbox Tests

Display—Test Passes

oMATHENX TESTS

BAD MATHBOX READY LINE

Figure 2-7 Mathbox Tests

Display-Test Fails

Self-Test

If matrix errors exist, the message MATRIX ERRORS will appear with the corresponding option switch settings for the diagnostic. Some matrix errors do not have a corresponding diagnostic. In this case, there will be no option switch setting.

Crosshatch Pattern Display

Press the auxiliary coin switch to obtain the Crosshatch Pattern display as shown in Figure 2-8. Verify the following display characteristics: ® Corners are closed and the diagonal lines form symmetrical diamond-shaped squares.

  • All four corners of the border are completely visible and are within %-inch from the black edge of the screen. ° Pattern is not tilted more than %-inch between corners. © Pattern is a uniform green color.

Figure 2-8 Crosshatch Pattern Display

If any of the preceding characteristics are not correct, refer to the linearity adjustment procedure in the Analog Vector- Generator schematic diagrams,

Page 25

Self-Test

Grid Pattern Display

Press the auxiliary coin switch to obtain a Grid Pattern display as shown in Figure 2-9. Verify that the following grid colors can be obtained, in order, by pressing either fire trigger: Red Green Blue Purple White Yellow Turquoise

Figure 2-9 Grid Pattern Display

Verify the following display characteristics: © Grid lines do not exhibit pincushioning or barreling and the lines are straight within %-inch.

  • Convergence shall not exceed 2.0 mm, as checked with the white grid. Lfany of the preceding display characteristics are not correct, refer to the linearity adjustment procedure in the Analog Vector-Generator schematic diagrams and to the convergence adjustment procedure in the Display Manual. Star Wars

Intensity Test Display Press the auxiliary coin switch to obtain the Intensity Test display as shown in Figure 2-10. Verify the following display characteristics: ¢ Top row of color bars are red, blue, and green. © — Allthree sets of color bars have six lines with the same intensity. « Bars underneath the top row of color bars are white.

  • Bars underneath the white color are yellow, turquoise, and purple.
  • DIM, LOW, and HIGH appear in the bottom center of the display. If the word OFF can be seen, the display is too bright. If the word LOW cannot be seen, the display is not bright enough.

INTENSITY TEST

Figure 2-10 Intensity Test Display

If the preceding display characteristics are not correct, refer to the Display Manual for the brightness adjustment procedure or to determine the possible cause of failure.

2-6

Page 26

Star Wars

Bipolar Offset Test Display Press the auxiliary coin switch to obtain the Bipolar Off: set Test TEST display as shown in Figures 2-11 and 2-12 The line width should be 4-inch or less. If not, adjust the X/Y bipolar offset potentiometers located in the digital-toanalog converter and bipolar current sources circuit on the Analog Vector-Generator PCB.

ALIGN THE BOXES

Figure 2-11 Bipolar Offset Test Display—Test Passes

SIP TERT

Figure 2-12 Bipolar Offset Test

Display—Test Fails

Self-Test

Scale Test Display Press the auxiliary coin switch to obtain the Scale Test Linear display as shown in Figure 2-13. A large green square should appear in the center of the screen and then smoothly shrink to a point. Next, a large green SCALE TEST LINEAR AND BINARY squate appears and shrinks smoothly, then pauses and continues to shrink. There should be eight pauses before the square shrinks to a point. After each pause and just when the square begins to shrink, the size of the square should not change appreciably. If a large change in the size of the square occurs, an error may exist. After the eighth pause, the sequence repeats with the Scale Test Linear and Binary display as shown in Figure 2-14,

SCALE TEST LINEAR

Figure 2-13 Scale Test Linear Display

SCALE TEST LINEAR AND BINARY

Figure 2-14 Scale Test Linear and Binary Display

Page 27

Self-Test

Raster Screen Display

Press the auxiliary coin switch to obtain the Raster Screen display as shown in Figure 2-14. This display is the last of the self-test displays and is used by the manufacturer to adjust the white tracking of the display circuitry.

Figure 2-15 Raster Screen Display

NOTE Pressing the auxiliary coin switch to end the preceding Raster Screen display will repeat the self-test sequence starting with the Switch Test display. If desired, turn the self-test switch off, then on again, to obtain the Accounting and Game Times display.

Star Wars

Page 28

Troubleshooting

This chapter contains a discussion of troubleshooting aids and techniques to assist the service technician when a trouble is suspected in this game. Most troubles can be located quickly by following the information in this chapter. However, if problems persist, contact your nearest Atari Customer Service office listed on the inside front cover of this manual for assistance. A thorough knowledge of game operation is desirable for effective troubleshooting. In addition to the operation and service information in the Schematic Package Supplement included with this manual, refer to The Book, A Guide To Electronic Game Operation and Servicing, available from Atari, Inc., for more information on coin-operated electronic games.

NOTE We recommend that troubleshooting and repair procedures be performed by a qualified electronic technician.

Chapter 3

Page 29

‘Troubleshooting

Troubleshooting Aids

‘Troubleshooting aids are provided throughout this manual and the Schematic Package Supplement. The following information is intended to acquaint the service technician with the portions of these documents that contain useful troubleshooting and repair information. Assembly and Component Locations The illustrated parts lists in Chapter 5 illustrate the locations of assemblies and components. Printed-circuit board (PCB) illustrations aid in rapidly locating components contained on the corresponding schematic diagram(s). Schematic Diagrams Complete schematic diagrams are provided in the Schematic Package Supplement. Component designations and their electrical values are included on the schematic diagrams. A memory map and a key to the schematic reference designators and symbols are also included in the Schematic Package Supplement. A block diagram of the major Circuits on the game PCB (with sheet numbers to aid in locating the appropriate schematic diagrams) is included in the Schematic Package Supplement.

Troubleshooting Procedures

This game will test itself and provide data to aid in localizing troubles toa major circuit. Self-test procedures are provided in Chapter 2. Refer to the following section on Troubleshooting Techniques for a suggested troubleshooting sequence that uses the self-test procedures.

Troubleshooting Techniques

The following troubleshooting steps are arranged in a sequence recommended for locating a defective component. The procedure begins with a check of the simple trouble possibilities and progresses to mote extensive procedures for localizing the trouble to an assembly or major circuit, and then to a defective component.

Check Switch Settings

Incorrect switch settings can sometimes indicate a problem that does not exist. Refer to Chapter 1 Set-Up, to verify that the game has been installed properly and that the switches are set to their correct positions. Check for proper operation in all game-play modes.

Toavoid electrical shock, turn the game off before removing or replacing components. Star Wars

Check Fuses Check for open fuses. Refer to the Power Supply Assembly Parts List in Chapter 5, Illustrated Parts Lists, and to the Display Manual, for the location and rating of each fuse used in this game. Make sure that replacement fuses are the proper type and rating,

Check Power-Supply Voltages Improper operation ofall circuits usually indicates a power supply problem. Check that the proper line voltage is available to the power supply.

localize Trouble Determine the trouble symptom. Use the wiring diagrams in the Schematic Package Supplement to determine which assemblies or major circuits could cause the trouble. Perform the self-test procedure provided in Chapter 2 Visual Check Visually check for obvious problems in the portion of the game where a trouble is suspected. For example, check for loose or defective solder connections, integrated circuits loose in their sockets, loose cable connections, broken wires, damaged printed-circuit boards or components.

Check Individual Components

CAUTION Transistors and integrated circuits solderedin place are difficult to remove without damaging, the printed circuit board or component. Be extremely careful when removing these components.

Check soldered-in components by disconnecting one end to isolate the measurement from the affects of the surrounding circuitry. Often, direct substitution is the most practical way to determine ifa component is faulty. However, eliminate the possibility of some other circuit problem existing which could damage the substitute component. Repair the Assembly Repair or replace the defective part. Refer to Chapter 4, Maintenance and Repair for special repair and replacement procedures. Check for proper operation of any repaired circuit.

Page 30

Maintenance

The maintenance procedures provided in this chapter are for those items which are subject to the most severe use. ‘To assure the maximum trouble-free operation from this game, Atari recommends that periodic routine maintenance be performed on the game components described in the following procedures. How often routine maintenance is performed depends upon the game environment and frequency of play.

To avoid possible electrical shock hazard, unplug the game prior to performing any maintenance.

Chapter 4

Page 31

Maintenance ‘Star Wars

Cleaning Requirements

This game cabinet and display shield may be cleaned with any non-abrasive household cleaner. The coin mechanism should be cleaned periodically with hot or boiling water anda mild detergent. A toothbrush may be used to remove any stubborn build-up of residue in the coin path. After cleaning the coin mechanism, flush thoroughly with hot or boiling water and blow out all of the water with compressed air. Compressed air is also recommended for cleaning dust from the interior of the cabinet.

Opening the Control Panel

1, Unlock and remove the rear access panel.

  • Reach up through the rear of the cabinet to the top of the control panel to remove the two nuts and washers that secure the control panel using a %-inch combination wrench.
  • Lift the control panel at the top edge and tilt ittoward you. The control panel has foam tape on it. Make sure the tape is in good condition.

4-2

Page 32

Star Wars

Flight Control Maintenance

Routine preventive maintenance on the flight control involves lubricating the moving parts and checking the mounting screws and nuts for proper tightness approximately every four months. The flight control consists of a handle assembly and a steering assembly. The handle assembly controls the vertical motion, and the steering assembly controls the horizontal motion of the display. Routine maintenance can be performed without removing the flight control assembly from the game. After any corrective maintenance is performed, the flight control should be recalibrated as described in Chapter 1, Refer to Figures 4-1 and 4-2 for the locations of the parts mentioned in the following procedures. Routine Maintenance Routine preventive maintenance on the flight control involves lubricating the moving parts and checking the mounting screws and nuts for proper tightness approximately every four months. Lubrication. Perform periodic lubrication of the flight control assembly as follows (see Figures 4-1 and 4-2):

  • Open the control panel as previously described in this chapter.
NOTE The handle-assembly covers are attached with tamper-proof socket screws. A special #,-inch hex-key tool is supplied with each game (Atari part no. 178126-001).
  • Use the special 42-inch hex-key tool to remove the four tamper-proof socket screws from the handle assembly cover.
  • Lift off the handle assembly cover and lubricate the following parts inside the flight control: (Refer to Figures 4-1 and 4-2 for an illustration of the lubrication points.)
  • Apply two drops of light machine oil lubricant (Atari part no. 107013-00)) to the insides of the four shaft bearings. ° Brush a light film of Nyogel 779 lubricant (Atari part no. 178027-001) onthe teeth of the twosmalt spur gears. ¢ Apply a small amount of WD-40 or a light machine cil to the potentiometer shafts as needed for squeaking. Screw and Nut Tightness. Use the appropriate hex-head and combination wrenches to check the hex-head cap screws and mounting nuts for tightness. Refer to Figures 41 and 4-2 foran illustration of the cap screw andmounting nut locations. Maintenance

Removing the Handles Perform the following procedure to remove the handles from the handle assembly (see Figure 4-1):

NOTE The handles on the handle assembly are assembled with tamper-proof cap screws. A special 42-inch hex-key tool is supplied with each game (Atari part no. 178126-001) to temove the tamper-proof cap screws.

1, Use the special 42-inch hex-key tool to remove the four tamper-proof cap screws that hold the covers on the handles. Be careful when removing the covers because the trigger and pushbutton springs can fall free from the handles.

  • Unsolder the three harness wires from the trigger and pushbutton microswitches inside each handle,
  • Use the special 4,-inch hex-key tool to remove the four tamper-proof cap screws that hold the handles to the shaft. Gently slide the handles from the shaft.
  • Reassemble in reverse order.

Removing the Flight Control

NOTE Certain corrective maintenance procedures can be performed with the flight control attached to the control panel. However, for convenience and to avoid damaging the control panel, we recommend that the flight control be removed from the control panel before any maintenance is performed.

Perform the following procedure to remove the flight control from the contro! panel:

  • Open the control panel as previously described.
  • Unplug the flight-contro! harness assembly.
  • Usea %,-inch combination wrench to remove the four locknuts and washers that mount the flight control to the control panel. 4, Carefully guide the flight control through the hole in the control panel.
Page 33

Maintenance

Disassembling the Handle Assembly

Perform the following procedure to disassemble the handle assembly (see Figure 4-1):

NOTE Removing the handle assembly from the steering assembly is not necessary to perform the procedure below. However, if you wish to do so, refer to Disassembling the Steering Assembly in this chapter for the procedure that describes how to separate the two assemblies.

1, Use the special %,-inch hex-key tool to remove the four tamper-proof cap screws from the handleassembly covers.

  • Remove the handles as previously described.
  • Gently pull the harness wires out of the hollow shaft. 4, Usea %,-inch hex driver to remove the cap screw and washer that hoid the spring handle pin to the handle assembly shaft.
  • Slide the spring-handle pin out of the shaft.
  • Usea %,-inch hex driver to loosen the cap screw that holds the large (60 tooth) spur gear to the shaft.
  • Slide the large (60 tooth) spur gear down the shaft to expose the shaft retainer on the right side.
WARNING Shield your face and eyes when prying out the retainers because they can fly loose at a high velocity. Cover the retainers with a rag or any material that will trap the retainer.
  • Use arightangle slotted screwdriver, or equivalent, to pry the retainer from the shaft.
  • Repeat steps 7 and 8 to remove the retainer on the opposite side.
  • Gently slide the shaft from the housing. Be careful not to lose the torsion springs. ll. Usea %,-inch hex driver to loosen the cap screw that holds the small (14 tooth) spur gear to the poten. tiometer shaft.
  • Use a ¥%-inch combination wrench to remove the nut and washer that hold the potentiometer to the mounting bracket.
  • Slide the potentiometer from the bracket. Be careful not to lose the small spur gear, nut, and washer.
  • Usea %,-inch hex-head wrench and %-inch combination wrench to remove the two bumpers from the frame.
  • Reasscmpble the tiandle assembly as described in the following procedure.

4-4 Star Wars

Reassembling the Handle Assembly

Follow the steps below to reassemble the handle assembly (see Figure 4-1):

  • Use a %,-inch hex driver and 4-inch combination wrench to install the two bumpers on the frame.
  • Insert the large (60 tooth) spur gear. with the collar facing away from the bearing. Hold the gear inline with the bearing hole. (The gear fits through the slot on the right front of the frame.) 3, Slide the shaft through the right-hand bearing and the spur gear. Do not insert the shaft past the outsicle edge of the spur-gear collar.
  • Apply aheavy film of Nyoge! 779 iubricant (Atari part no. 178027-001) to the inside of the springs.
  • Hook the straight end of the first torsion spring through the hole closest to the right side of the frame.
  • Hoid the first torsion spring in line with the shaft so that the looped end of the spring is facing away from the spur gear.
  • Slide the shaft just through the first torsion spring,
  • Hook the straight end of the second torsion spring through the hole closest to the left hand bearing.
  • Hold the second torsion spring in line with the shaft so that the looped end of the spring is facing the first torsion spring. 10, Slide the shaft through the second torsion spring and the left-hand bearing.
  • Position the shaft so that the retainer grooves are just inside the bearings.
  • Install the two retainers in the shaft grooves.
  • Turn the shaft so that the two large holes and the smaller centered hole are facing upward. 14, Locate the hole in the spring-handle pin. Insert the end of the spring handle pin that is closest to the hole through the slot in the frame and through the hole in the shaft. Make sure that both torsion spring looped ends are wrapped over the spring handle pin.
  • Position the spring-handle pin so that the hole in the pin is aligned with the hole in the shaft.
  • Usea %,-inch hex driver to tighten the cap screw and washer that secure the pin to the shaft.
  • Align the cap screw in the spur-gear collar with the threaded hole in the shaft, and use a %,-inch hex driver to tighten the cap screw.
  • Insert the potentiometer shaft through the hole in the mounting bracket, Place the washer, nut, and small (14 tooth) spur gear (with the collar facing inward) onto the shaft before fully inserting the shaft through the bracket.
Page 34

‘Star Wars

  • Align the potentiometer so that the tab key is inserted into the keying slot.
  • Usea %-inch combination wrench to slightly tighten. the nut on the potentiometer shaft.
  • Turn the potentiometer shaft so that the flat side faces the center wire terminal.
  • Align the cap screw on the small (14 tooth) spur gear with the flat side of the shaft. Use a %4-inch hex driver to tighten the cap screw.
  • Slide the potentiometer forward so that the teeth on the two spur gears are tightly meshed; then pull the potentiometer and small (14 tooth) spur gear away from the large spur gear about %,-inch.

Wire & Cable Tie

Retainer Potentiometer

Rea White Black

Bearing

Second Torsion Spring

Labeled Sleeve (R} Spring Pin ®)

First Torsion Spring Spur Gear Collar Large Spur Gear Maintenance

24, Use a ¥-inch combination wrench to tighten the potentiometer to the mounting bracket.

  • Perform the procedure for installing the harness assembly provided at the end of this chapter.
  • Install the handles in the reverse order of the removal procedure previously described. Do not install the handle covers until the harness is installed and the proper wires are soldered to the trigger and pushbutton microswitches.
  • Install the handle assembly cover and use the special 32-inch hex-key tool to tighten the four tamper-proof socket screws that secure the cover to the handle assembly.

Tab Key

Harness Assembly

Handle Assembly ~~ St je Collar -~

‘Bumper

‘Keying Slot Trigger Microswitch

‘Small Black

Spur Gear (Common)

White (Normally Open)

Pushbutton Microswitch Black (Common) Red (Normally Open)

Tamper-Proof Cap Screw

Figure 4-1 Handle Assembly

Page 35

Maintenance

Disassembling the Steering Assembly Perform the following procedure to disassemble the steering assembly (see Figure 4-2):

  • Remove the handle covers as described earlier in this chapter. Remember, be careful when opening the handles because the pushbutton and trigger springs may fall out.
  • Unsolder the three harness wires from the vertical potentiometer, handle pushbutton microswitch, and trigger microswitch.
  • Usea %,-inch hex driver (or ball-end driver) to remove the three cap screws that hold the steering-assembly shaft to the handle-assembly frame. 4, Gently pull the two assemblies apart. Make sure the harness wires are free to slide out of the handleassembly shaft.
  • Use a ¥,-inch wrench to remove the anchor nut on the end of the anchor pin. (The anchor nut faces the open end of the frame.) . Slide the anchor pin out of the shaft.
  • Grasp the large (60 tooth) spur-gear and slide the shaft from the frame. The bearing spacer, torsion springs, and large flat washer will fall free.
  • Use a %,-inch hex driver to remove the cap screw holding the large spur gear to the steering shaft anda 44-inch hex driver to remove the set screw that holds the small spur gear to the potentiometer shaft.
  • Usea %-inch combination wrench to remove the nut and washer that hold the potentiometer to the frame.
  • Unsolder the three harness wires from the potentiometer terminals.

Shield your face and eyes when prying the retainer from the shaft since the retainer can fly loose at a high velocity. Cover the retainer with arag or any material that will trap the retainer.

ll. Use a slotted screwdriver, or equivalent, to remove the retainer from the shaft.

  • Use a %-inch hex driver and %-inch combination wrench to remove the two bumpers from the frame.
  • Reassemble the steering assembly as described in the following procedure.

Reassembling the Steering Assembly

Perform the following procedure to reassemble the steering assembly (see Figure 4-2):

  • Use a %2-inch hex driver and 4-inch combination wrench to install the two bumpers to the frame.

4-6 nN

10.

14,

15.

16. Star Wars

Snap the retainer into the groove in the shaft and slide the large flat washer down the long end of the shaft and against the retainer. Apply a heavy film of Nyogel 779 lubricant (Atari part no. 178027-001) to the inside of the springs. Hook the straight end of the first torsion spring through the hole closest to the rear of the frame. Slide the shaft through the outside bearing and the first torsion spring, Hook the second torsion spring through the hole on the opposite side and closest to the front of the frame. Slide the shaft through the second spring and the opposite bearing. Turn the shaft so that the threaded hole at the retainer end of the shaft faces up toward the open side of the frame. The hole through the center of the shaft will then be perpendicular to the open side of the frame. Use a 65-inch combination wrench to install the anchor pin and nut through the hole in the center of the shaft. Make sure the torsion spring looped ends are wrapped under the anchor pin and nut. Slide the large (60 tooth) spur gear onto the shaft with the collar facing out. Align the cap screw in the spur-gear collar with the threaded hole in the shaft and use a %,-inch hex driver to tighten the cap screw. Insert the potentiometer shaft through the hole in the frame and align the potentiometer so that the tab key is inserted into the keying slot. . Install the washer and nut on the potentiometer shaft but do not tighten. . Turn the potentiometer shaft so that the flat side faces the center wire terminal. . Align the cap screw on the small (28 tooth) spur gear with the flat side of the shaft and slide the small spur gear (with the collar facing inward) onto the potentiometer shaft.

Position the spur gear so that its teeth mesh with those of the large spur gear and use a %4-inch hex driver to tighten the set screw. Slide the potentiometer forward so that the teeth on the two spur gears are tightly meshed; then slide the potentiometer and small spur gear away from the large spur gear about %,-inch. Use a %-inch combination wrench to tighten the potentiometer to the frame. Slide the bearing spacer over the shaft at the end opposite the spur gears. . If necessary, lubricate the steering assembly as previously described.

Page 36

Star Wars

NOTE The remaining steps describe the procedure for attaching the steering assembly to the handie assembly.
  • Insert the steering-assembly shaft into the collar on the handle-assembly frame.
  • Align the three holes in the steering-assembly shaft with the three holes in the handle-assembly collar.
  • Usea %,-inch hex driver (or ball-end driver) to tighten the three cap screws.
  • Install the harness assembly as described in the following procedure,

Retainer

First Torsion Spring

Second Torsion Spring

Anchor Pin

Shaft

Bumper Bearing Spacer Black Maintenance

Installing the Harness Assembly

Perform the following steps to install the harness assembly into the flight control (see Figures 4-1 and 4-2):

  • Remove the handle covers as described under Removing the Handles.
  • Guide the harness wires into the spur-gear end of the hollow steering-assembly shaft. Route and solder the wires to the potentiometers and microswitches, Note that the wire bundle that goes to the right handle is identified with a labeled sleeve (R).
  • Install the wire ties and the ground clip. >»

Harness Assembly

eA fy

R Ta NE af B Zo

‘Small Spur Gear

Large Flat Washer

Green

Keying Slot

Ground Clip

Anchor Nut

Potentiometer

Figure 4-2 Steering Assembly

4-7

Page 37

Maintenance

Removing the CRT Assembly

WARNING The cathode-ray tube (CRT) assembly may implode if struck or dropped. Shattered glass can cause personal injury within a 6-foot radius. To reduce the risks of injury to people or of damage to the game components, we recommend that two people perform the following removal procedures.

Perform the following procedure to remove the CRT assembly from the game (see Figure 4-3): Remove the rear access panel from the cabinet.

  • Discharge the high-voltage from the CRT before proceeding. The video display contains a circuit for discharging the CRT high voltage to ground when power is removed. However, to make certain, always discharge the CRT as follows: a. Attach one end ofa large, well insulated, 18-gauge jumper wire to ground. b. Momentarily touch the free end of the grounded jumper to the anode by sliding it under the anode cap. c. Wait two minutes and repeat part b. Disconnect the CRT neck-pin connector, anode lead, yoke connector (J105 on the Deflection PCB), degaussing coil connector (J104 on the Deflection PCB), and the 1- pin DAG spring connector.

Lower Housing

Display Shield Display Bezel Star Wars

Open the control panel as previously described in this chapter. Use a %-inch hex-head wrench to remove the four socket screws and washers that secure the lower housing to the cabinet. Carefully remove the lower housing, display shield, and display bezel.

CAUTION Be extremely careful when removing the CRT mounting bolts because the CRT assembly can. fall. We recommend that a second person carefully hold the CRT neck while the mounting bolts are being removed.

Use a %-inch combination wrench to remove the four bolts and washers from the front of the display mounting bracket. Carefully lift the CRT assembly from the front of the cabinet. Replace in reverse order.

NOTE Readjust the brightness, purity, and convergence as described in the Display Manual whenever the CRT is replaced.

CRT Neck

Mounting Bracket

Figure 4-3 Removing the CRT Assembly

Page 38

Star Wars Maintenance

Wiring the Utility Panel Controls

Refer to Figure 4-4 for the proper wire connections when replacing the controls that are mounted on the utility panel. White/Yellow

Orange

E Yellow Before removing or repairing the utlitypanel, turn the game off. Players may receive an electrical shock ifthe Utility panelis not properly grounded! After servicing any parts onthe pan-

el, make sure thatthe ground wireis

firmly attached to the back of the coin White/Red counter.

Orange/Blue Orange/White/Violet

First Coin Counter Second Coin Counter

Black (Common)

Gray Normally Oper ‘ Open) White

NOTE Only the ireland-built cabinet has two coin counters,

Figure 4-4 Utility Panel Wire Colors

Page 39

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 40

Illustrated Parts Lists

This chapter provides information you need to order parts for your game. Common hardware (screws, nuts, washers, etc.) has been deleted from most of the parts lists, However, a parts list is included for the hardware to mount the printed-circuit boards (PCB) to the cabinet. The PCB parts lists are arranged in alphabetical order by component. Each component subsection is arranged alphanumerically by reference designator. Other parts lists are arranged alphanumerically by Atari part number. In these parts lists, all A-prefix numbers come first. Following these are numbers in sequence evaluated up to the hyphen, namely 00- through 99; then 000598through approximately 201000- When ordering parts, please give the part number, part name, number of this manual, and serial number of your game. This will aid in filling your order rapidly and correctly. We hope the results will be less downtime and more profit from your game. Atari Customer Service numbers are listed on the inside front cover of this manual.

\ \

Chapter 5

Page 41

Illustrated Parts Lists Star Wars

Fluorescent Tube &S| See Figure 5-4.

A040378-01 Attraction Panel | 040369-01 iction Panel with Decal Attraction Panel Retainer

78-6900404 Tape 040370-01 Speaker Grille

040371-01 040377-01 Display Shield Display Bezel

A040375-01 Lower Housing & Decal Assy. Flight Control See Figure 5-3

A040374-01 Control Panel Assy. ‘A040373-01 Control Panel with Decal ‘A040233-01 Flight Control 178034-024 EMolding ososrat1 Control Panel 040380-03 Decal-not shown 78-6900402 Coin Door Assy. Tape See Figures 5-6 or 5:7

Utility Panel Assy. See Figure 5-5

78-3201 Glide

038091-01 Molded Coin Box

Figure 5-1A Cabinet-Mounted Assemblies US-Built Cabinet A040344-01 A

Page 42

Star Wars: Illustrated Parts Lists

A040345-01 Cabinet Assy.

037332-01 Ventilation Grille

A038881-01 Lock

A200009-01 Atari Display Kit Assy. Refer to the Display Manual 040129-01 High-Voltage PCB Assy. Access Panel Refer to the Display Manual

Deflection PCB Assy. Refer to the Display Manual

: 040376-01 040376-02 Static Shield Static Shield 3 EMI Cage 038870-01 See Figure 5-9 Coin Box Enclosure Regulator/Audio || PCB See Figures 5-9 & 5-11 A040467-01 Power Harness Assy. A040466-01 Main Harness Assy.

Fan Bracket Fan & Bracket Assy. 178093-001 Fan Blade Guard

Power Supply Assy. See Figure 5-8 037243-01 Base Plate EMI Shield PCB See Figures 5-9 & 5-10

‘A038600-01 Power On/Off Switch Assy.

009992-01 On/Off Switch Cover A037453-01 Power Cord

Figure 5-1A Cabinet-Mounted Assemblies, continued US-Built Cabinet A040344-01 A

5-3

Page 43

Illustrated Parts Lists Star Wars

Cabinet-Mounted Assemblies US-Built Cabinet Parts List

Part No. Description

A037453-01Strain-Relief Power Cord(U.S. and Canada)

A038600-01 Power On/Off Switch and Mounting Plate Assembly A038881-01 Lock Assembly (for rear access panel) Acceptable substitute is part no. A038881-03 A040345-01 Cabinet Assembly (includes glides and PCB retainers, but not the rear access panel)

A040374-01 Control Panel Assembly—includes: A040233-01 Flight Control 040372-01 Control Panel 040380-03 Decal for Control Panel (not shown)

A040375-01 Lower Housing and Decal Assembly A040378-01 Attraction Panel with Decal A040466-01 Main Harness Assembly A040467-01 Power Harness Assembly

A200009-01 Atari 19-Inch Color XY Display Kit Assembly—includes: A201106-01 Cathode-Ray Tube Assembly (not shown) A201014-01 Deflection PCB Assembly A201012-01 High-Voltage PCB Assembly

The following four items are technical information supplements to this game.

SP-225 Star Wars Schematic Package ST-225-01 Star Wars Label with Self-Test Procedure and Option Switch Settings TM-225 Star Wars Operators Manual with Illustrated Parts Lists TM-239 Atari 19-Inch and 25-Inch Color XY Display Manual

78-3201 Adjustable Glide 78-6900402 Vinyl Foam Single-Coated Adhesive Tape, ¥4-Inch Wide x 4- Inch Thick (apply 36 inches to the surrounding edge of the control panel-not shown) 78-6900404 Vinyl Foam Single-Coated Adhesive Tape, %-Inch Wide x %- Inch Thick (apply 23 inches to the top edge of the attraction panel) 009992-01 On/Off Switch Cover

034536-01Foam Pad—1%-Inch Thick(located between the Deflection PCB and the cabinet wall-not shown)
034536-02Foam Pad—2-Inch Thick(located between the High-Voltage PCB and the cabinet wall, between the Reg-

ulator/Audio PCB and the EMI Cage, and between the EMI Cage and the cabinet wall-not shown)

037243-01Base Plate for Power Supply(not shown)

037332-01 Ventilation Grille 038091-01 Molded Coin Box 038870-01 Coin Box Enclosure 040129-01 Rear Access Panel (does not include lock) 040369-01 Attraction Panel Retainer

040370-01 Speaker Grille 040371-01 Video Display Shield 040376-01 Static Shield 040376-02 Static Shield 040377-01 Video Display Bezel

5-4 (Continued on next page)

Page 44

Star Wars Illustrated Parts Lists

Cabinet-Mounted Assemblies US-Built Cabinet Parts List, continued

Part No. Description

A040547-01 Fan and Bracket Assembly—includes: 040546-01 Fan Bracket 171002-001 Fan 178034-024 34-Inch Black Plastic T-Molding 178048-001 2-Inch Rigid Caster 178093-001 Fan Blade Guard 178126-001 Hex Wrench for Cabinet-Mounted Assys. (not shown—it is shipped in the coin box and required for the tamper-proof screws on the flight control)

5-5

Page 45

Illustrated Parts Lists

Information on Ireland-built game not available for first printing.

Figure 5-1B Cabinet-Mounted Assemblies A4040344-10 B Ireland-Built Cabinet Star Wars

Page 46

Star Wars Illustrated Parts Lists

Information on Ireland-built game not available for first printing.

Figure 5-1B Cabinet-Mounted Assemblies, continued A040344-10 B Ireland-Built Cabinet

5-7

Page 47

Ulusirated Parts Lists

Information on Ireland-built game not available for first printing. Star Wars

Page 48

Star Wars

Information on Ireland-built game not available for first printing. Illustrated Parts Lists

5-9

Page 49

Illustrated Parts Lists

040379-04 Attraction Panel Decal

oat Center Housing Decal

Figure 5-2 Star Wars Decals

Page 50

Star Wars

Figure 5-2 Star Wars Decals Illustrated Parts Lists

Parts Lists

Part No. Description

040379-03 Attraction Panel Decal 040380-03 Control Panel Decal 040382-07 Flight Control Decal 040382-04 Left Display-Housing Decal

040382-05 Center Display-Housing Decal 040382-06 Right Display-Housing Decal (not shown)

Page 51

si Illustrated Parts Lists tar Wars:

g 176025-3604

  • Cap Screw

040093-02 040091-01 72-8812 Left Handle Cover Left Handie Cap Screw

A040468-01 Harness 176022-3606 . a | Cap Screw 176024-360! Z Wee S Cap Screw <i

73-20807 Roll Pin

040303-01 176026-3610 | > % 040252-01 72-1206F Trigger Cap Screw ~\/ 77) Compression Spring ‘Screw eannes-01 040244-01 2 < Right Handle Cover Spring Pin ‘

040246-01 A040247-01 Handle Spring Handle Assy, Frame 040242-01 = Handle Shatt

040235-01 atin0i-08 Gear Right Handle e& re 176022-3604 , 460026-001 Cap Screw ‘ Switch i7e026-3610 Screw

Figure 5-3 Flight Control Assembly A040233-01 A

5-12

Page 52

Star Wars Illustrated Parts Lists

178012-001 Retaining Ring

040238-01 Pin 175002-001 \ Large Washer

040234-01 177010-241 Steering Shatt Nut 040239-01 175002-004 Spring R@ Flat Washer \ A040236-01 040237-01 Steering Assy. Frame Nut

Washer \ to.0008 Potentiometer

040241-01 040240-01 Spacer Bearing Bumper

See Chapter 4 for lubrication information.

Figure 5-3 Flight Control Assembly, continued A040233-01 A

5-13

Page 53

i, Illustrated Parts Lists ; Flight Control Assembly Parts List Star Wars

Part No. Description

A040236-01 040243-01 040555-01 72-L28510

A04024701 040243-01 040556-01

-A040251-01 040248-01 040382-07

A040468-01 19-9026 72-1206F 72-8010

72-8812 73-20807 75-048 75-07020

040091-02 040091-01 040093-01 040093-02

040096-01 040234-01 040235-01 04023701

040238-01 040239-01 040240-01 040241-01

040242-01 040244-01 040246-01 040249-01

040252-01 040303-01 040473-01 160026-001

175002-001 175002-004 176022-3604 176024-3605,

176022-3606 176025-3604 176026-3610 177010-241

178012-001 178101-003 Steering Assembly Frame—includes: Modified Bearing Steering Frame Weldment #%4-20 x %-Inch Long Self-Clinching Stud

Handle Assembly Frame—includes: Modified Bearing Frame Handle Weldment

Steering Cover and Decal Assembly—includes: Cover Decal

Flight Control Hamess Assembly 5 kQ Potentiometer #2-56 x ¥-Inch Cross-Recessed Pan-Head Machine Screw #10-32 x ¥-Inch Socket-Head Cap Screw

#8-32 x ¥4-Inch Socket-Head Cap Screw f-Inch Diameter x 7jg-Inch Long Spring Roll Pin #8 Split Lock Wasker 0.390-Inch I. D. Flat Washer

Right Handle Left Handle Right Handle Cover Left Handle Cover

Button Steering Shaft 60-Tooth Spur Gear Anchor Nut

Anchor Pin Steering Torsion Spring Stop Bumper Spacer Bearing

Handle Shaft Spring Pin Handle Torsion Spring 14Tooth Spur Gear

Compression Spring Trigger Jumper Wire SPDT Snap Switch

0.750-Inch I. D, Large Washer #10 Flat Washer #6-32 x %s-Inch Self-Locking Socket-Head Cap Screw #632 x 4_-Inch Tamper-Proof Self-Locking Socket-Head Cap Screw

#6-32 x %-Inch Tamper-Proof Socket-Head Cap Screw #632 x %4-Inch Tamper-Proof Self-Locking Button-Head Cap Screw #6-32 x %-Inch Tamper-Proof Socket-Head Cap Screw #10-32 Nylock Hex Nut

Retaining Ring for .750-Inch Diameter Shaft 28Tooth Spur Gear

5-14

Page 54

Star Wars IWustrated Parts Lists

NOTE To ensure that the fluorescent tube Ld i starts, make sure the ground wire is peaker firmly attached to both the ballast transformer and the steel tube c = bracket oe

70-304 Tube

99-11006 Tab 99-11003 Starter

A040469-01 Harness

037469-01 Bracket

142028-001 Transformer

79-561816P ‘8037540-01 Wire Net Ground Wire

Figure 5-4 Fluorescent Tube and Speaker Assembly A040383-01 A Parts List

Part No. Description

A037540-01 Ground Wire with Ring Lug A040469-01 ‘Tube and Speaker Harness Assembly 70-304 18-Inch, 15-Watt, Cool White Fluorescent Tube

79-561816P Spring-Connector Wire Nut for 16- to 18-Gauge Wires 99-11003 Fluorescent Tube Starter 99-11006 Fluorescent Tube Locking Tab (consists of two pieces) 99-11009 Starter Socket

037469-01 Steel Tube Bracket 142028-001 60 Hz, 118 V, Ballast Transformer (used on A040378-01 assembly) 148001-013, 6 x 9-Inch Oval, 4 2, 6-Ounce, Shielded High-Fidelity Speaker 179035-001 2-Pin Fluorescent Tube Holder

5-15

Page 55

Illustrated Parts Lists Star Wars

A039254-01 Harness Assembly

Before removing or repairing the uttlty panel, turn the game off. Players may receive an electrical shock ifthe utility panel is not properly grounded! After servicing any paris on the panel, make sure that the ground wireis firmly attached to the bracket.

A002465-01 Coin Counter

176018-002 Screw

69-001 SelfTest Switch 75-9910W0 Stamped Nut 119006-103 040412-01 Volume Control Bracket

NOTE Only the Ireland-built cabinet has two coin counte 62-041 Auxiliary Coin Switch

Figure 5-5 Utility Panel Assembly A040413-01 A Parts List

Part No. Description

A002465-01 Coin Counter A039254-01 Volume Control Harness Assembly (includes grounding clip) 62-041 SPDT Pushbutton Auxiliary Coin Switch with Black Cap 69-001 DPDT Self‘lest Switch 040412-01 Component Bracket 75-9910W0 15/32-32 Stamped Nut 119006-103 Volume Control 176018-002 #6-32 x 2-Inch Machine Screw

5-16

Page 56

Star'Wars Ilustrated Parts Lists

5-17

Page 57

Illustrated Parts Lists Star Wars

170000-001 Lamp.

  • a“ 179047-001 99:15023

Lamp Base EP - Base Plate

> & L A

99-15026 ag : > 99-15040 (Coin inlet) L . a tener 99-15056 Screw for Bezel

99-15025 Coin inlet

99-1505 Retaining Screw Ky Fl mss Pivot for Lever Hey

99-15027 S Side Plate ~ Coin Return Sy

99-15028 75-S14S, Coin Return Box Hex Nut

Switch

7214148 Screw

Figure 5-6 Vertically Mounted Coin Door 171034-xxx A

5-18

Page 58

Star Wars

A037542-01 Harness—not shown

99-15067 Lock Assy,

038091-01 Coin Box

99-15072 Door Frame

99-15073 Upper Door

99-15074 Lower Door

171034-001 — U.S, 25¢/25¢ Coin Door 471034-003 — Canadian 25¢/25¢ Coin Door 171034-005 — U.K. 10 P/50 P Coin Door

Figure 5-6 Illustrated Parts Lists

99-15067. Lock Assy. A s ») 99-15038 Bezel for Button

99-15001 thru 99-15011 Return Button

99-15070 Doors and Frame 99-15071 Clamp

Bezel for Cover

99-15036 SS Cover

99-15066 Screw

171034-006 -- U.K. 20 P/50 P Coin Door 171034-009 — German 2 DM/1 DM Coin Door 171034-010 — German 2 DM/5 DM Coin Door 171034-011 — German 1 DM/5 DM Coin Door 171034-015 — French 2 Frit Fr Coin Door

Vertically Mounted Coin Door, continued 171034-xxx A

5-19

Page 59

Illustrated Parts Lists Star Wars

Vertically Mounted Coin Door Parts List

Part No. Description

A037542-01 Harness Assembly 72-14148 #4-40 x %-Inch Cross-Recessed Pan-Head Steel Machine Screw 75-056 #6 Internal-Tooth Zinc-Plated Steel Lock Washer 75-9145 #4-40 Steel Machine Hex Nut

75-3414S, #4-40 x %-Inch 82° Cross-Recessed Flat-Head Steel Machine Screw 99-15001 Coin Return Button with U.S. 25¢ Price Plate 99-15002 Coin Return Button with U.S. $1 Price Plate 99-15003 Coin Return Button with German 1 DM Price Plate

99-15004 Coin Return Button with German 2 DM Price Plate 99-15005 Coin Return Button with German 5 DM Price Plate 99-15006 Coin Return Button with Belgian 5 Fr Price Plate 99-15007 Coin Return Button with French 1 Fr Price Plate 99-15008 Coin Return Button with Japanese 100 Yen Price Plate 99-15009 Coin Return Button with British 10 Pence Price Plate 99-15010 Coin Return Button with Australian 20¢ Price Plate 99-15011 Coin Return Bution with Italian 100 Lire Price Plate

99-15023 Base Plate 99-15025 Left Half of Coin Inlet 99-15026 Right Half of Coin Inlet 99-15027 Side Plate of Coin Return Box

99-15028 Base Plate of Coin Return Box 99-15029 Switch Bracket 99-15036 Metal Coin Return Cover 99-15038 Bezel for Coin Return Button

99-15039 Metal Bezel for Coin Return Cover 99-15040 Coin Return Lever 99-15042 Coin Switch for U.S. 25¢ 99-15052 Spring for Coin Return Button

99-15054 Pivot for Coin Return Lever 99-15055 Retaining Screw 99-15056 #4-40 x 4.-Inch Cross-Recessed Pan-Head Steel Machine Screw 99-15060 Switch Cover

99-15063 Screw for Hinge 99-15066 Screw for Clamp 99-15067 Lock Assembly 99-15070 Doors and Frame

99-15071 Clamp for Frame 99-15072 Door Frame 99-15073 Upper Door 99-15074 Lower Door

99-15075 Switch Adjuster 038091-01 Coin Box (Not included in assembly—Acceptable substitute is part number A03 7491-01) 176000-001 6.3 V Miniature Wedge-Base Incandescent Lamp 171006-035 Metal Coin Mechanism 179047-001 Lamp Base

5-20

Page 60

Illustrated Parts Lists Star Wars

171008-035 99-10140 Coin mechanism Panel assy.

75-9488 Va Locknut a

99-10116

99-10151 Left coin inlet

99-10080 Lamp socket

70-11-47 Lamp

Harness Bar retainer

99-10042 thru 99-10045 99-10154 A Bracket assy. } “ 99-10153 le. WZ . Coin switch assy. Coin return box eo. < a cl

esanic S

N\ Coin switch 99-10150 Switch cover

99-0075 thru 99-10078 Switch wire 99-1008 Retainer 75-1412S Screw

Figure 5-7 American-Made Coin-Door Assembly 171027-001 A

Page 61

Ilustrated Parts Lists Star Wars

99-10148 Lock assy.

72-HA1404C Screw 99-10142 Button housing,

99-1019 Coin doo: 99-10134 sororg | ver Button assy. ) 9940118

2 Sorin a 9

9.10141 99-10145—> ‘ Cam Ay AY Coin return cover

gS 99-10117 Coin retum door

a 99-0144 a \~— Channel clip ee Se

72-JA\405B Screw

99-10149 Service door

038091-01 Coin box 99-10143, Frame

Figure 5-7 American-Made Coin-Door Assembly, continued 171027-001 A

5-22

Page 62

Illustrated Parts Lists Star Wars:

American-Made Coin-Door Assembly Parts List

Part No. Description

171006-035 Metal Coin Mechanism for USS. $.25 65-441C Coin Switch 70-11-47 Miniature Bayonet Lamp 72-9406S #4-40 x ¥-Inch Truss-Head Screw 72-HA1404C #4-40 x %4-Inch Pan-Head Screw 72-JA1405B #4-40 x .31-Inch Pan-Head Screw 75-1412S #4-40 x %4-Inch Pan-Head Screw 75-9448 #4-40 Lock Nut

99-10008 Retainer 99-10042 Coin Switch Assembly for Belgium 5 Fr and U.S, $.25 99-10043 Coin Switch Assembly for German 1 DM, Japanese 100 Yen, Swiss 1 Fr 99-10044 Coin Switch Assembly for German 2 DM, Italian 100 L, US. $1.00 99-10045 Coin Switch Assembly for Australian $.20, German 5 DM, British 10 P 99-10068 Coin Return Chute 99-10075, Switch wire (included in coin switch assembly) 99-10076 Switch wire (included in coin switch assembly) 99-10077 Switch wire (included in coin switch assembly) 99-10078 Switch wire (included in coin switch assembly) 99-10080 Lamp socket 99-10081 Key holder 99-10096 Fastener 99-10104 Bar retainer 99-10105 Bar 99-1015. Spring 99-10116 Plastic Coin Return Lever 99-10117 Steel Coin Return Door 99-1018, Amber Coin Return Button 99-10119 Amber Coin Button for US. $.25 99-10134 Coin Button Cover 99-10139 Coin Door 99-10140 Coin Door Inner-Panel Assembly 99-10141 Diecast Coin Return Cover

99-10142 Diecast Button Housing 99-10143 Coin Door Frame 99-10144 Coin Door Channel Clip 9910145, Offset Cam. 99-10146 Coin Inlet Chute Assembly 99-10147 American-Made Coin Door Harness 99-10148 Lock Assembly 99-10149 Service Door 99-10150 Switch Cover 99-10151 Left Coin Inlet 99-10152 Right Coin Inlet 99-10153 Coin Return Box 99-10154 Bracket Assembly

Page 63

Illustrated Parts Lists Star Wars

NOTE Power supply base plate is not shown. For part number, see Figure 5A. A037395-01 (Transformer Assy.)

A021084-02 (Volt. Plugs) 29.053 (Capacitor)

034554-01 (Fuse Cover)

79-4411001 (Fuse Post) 78-70501SC (Cap. Bracket)

46-2017002 (Fuse)

A035891-02 (Fuse Harness) 034482-02 (Chassis)

46-301203 (Fuse)

037639.01 (Label)

78-2708 (Bushing)

A034630-01 (Fuse Beak) (Filter Assy.) 037641. fee 1 46-2014002 / (Fuses) aN ’ 79-15021001 ¢ A035890-01 (Term. Block) \ (Pwr. Harness) A034629-01 3A-MDA3501 © (Rectifier) (AC. Harn.)

Figure 5-8 Power Supply Assembly A037396-04 F

5-24

Page 64

Star Wars Illustrated Parts Lists

Power Supply Assembly Parts List

DesignatorDescriptionPart No.
cl27,000 yF, 15 VDC Electrolytic Capacitor29-053
cl2-Inch Diameter Capacitor Mounting Bracket78-70501SC
CRI‘Type-MDA 3501 Bridge Rectifier3A-MDA3501
FLPanel-Mounting Non-Indicating 3AG CartridgeType Fuse Post79-4411001
Fl7 A, 250 V, 3AG Slow-Blow Glass Cartridge“Iype Fuse46-2017002
FILabel for Fuse Value037639-01
F24 A, 250 V, 3AG Slow-Blow Glass Cartridge“Iype Fuse (Acceptable substitute is46-2014002

part no. 46-2014001, a 4 A, 125 V, 3AG Fuse)

F320 A, 32 V, 3AG Slow-Blow Glass Cartridge-Type Fuse46-301203
F4-F64A, 250 V, 3AG Slow-Blow Glass CartridgeType Fuse (Acceptable substitute is46-2014002

part no. 46-2014001)

F2-F65-Position 3AG Fuse Block with 4 -Inch Quick-Disconnect Terminals79-3206
F2-FOFuse Harness AssemblyA035891-02
F2~-F6Fuse Block Cover034544-01
F2-F6Label for Fuse Values037641-01
F42-Circuit Singie-Row Terminal Block (located under F4)79-15021001
FLIRFI Filter Assembly (designation not marked)A034630-01
j2Power Harness AssemblyA035890-01
3BVoltage Plug for 120 V (105-135 VAC, yellow wire color—plugs into J3)A021084-02
J4aAC Harness AssemblyA034629-01
Tl‘Transformer Assembly (designation covered)A037395-01

Nylon Type 6/6 Hole Bushing with %-Inch Inside Diameter x 5%,-Inch Outside 78-2708 Diameter x 4 -Inch Thick Power Supply Chassis Base 034482-02

Page 65

Illustrated Parts Lists Star Wars

037873-01 Spacer A038463-21 Analog Vector-Generator PCB See Figure 5-13

A040472-01 Interconnect Cable

72-1604F 178120-112 Screw PCB Support

NOTE The Federal Communications Commission requires that the game PCBs be housed in the EMI cage with the EMI Shield PCB attached. 178120-212 PCB Support

178120-206 PCB Support

A038461-21 Main PCB See Figure 5-12 175009-221 176015-112 Plastic Washer 178044-242 Grommet

A040255-01 Interconnect PCB 178045-442 Fastener

040260-21 Sound PCB See Figure 5-14 176021-004 Screw

A035435-02 Regulator/Audio || PCB See Figure 5-11

040301-01 Tray and Guides Assembly 4 040300-01 Waoario22 Mounting Tray

A037701-03 ith Guides Grounding clip EMI Cage wi _ nerenonn EMI Cage EMI Shield PCB See Figure 5-10

Figure 5-9A PCB Mounting Hardware US-Built Cabinet

Page 66

Star Wars Illustrated Parts Lists

PCB Mounting Hardware Parts List

Part No. Description

A035435-02 Regulator/Audio II PCB A037701-03 EMI Cage and Guides Assembly—includes: 178047-032 16-Inch Snap-In PCB Guide (four required) 037700-02 EMI Cage A038461-21 Star Wars Main PCB Assembly A038463-21 Stars Wars Analog Vector-Generator PCB Assembly A040255-01 Stars Wars Interconnect PCB Assembly A040258-01 EMI Shield PCB Assembly—includes: 72-1404F #4-40 x Y4-Inch Cross-Recessed Steel Screw 037873-01 Spacer 175009-221 Plastic Washer 178044-242 Grommet 178045-442 Snap-In Fastener A040260-21 Stars Wars Sound PCB Assembly A040301-01 Tray and Guides Assembly—includes: 040300-01 Mounting Tray for Regulator/Audio II PCB 178047-022 ll-Inch Snap-In PCB Guide (two required) A040472-01 Interconnect Cable 72-1604F #6-32 x %-Inch Cross-Recessed Pan-Head Screw 176015-112 #10 x 34-Inch Cross-Recessed Pan-Head Screw 176021-004 #8 x %-Inch Zinc Hex Washer-Head Screw (2 screws attach the mounting tray to the EMI cage, and 2 screws attach the Regulator/Audio II PCB to the mounting tray—acceptable substitute is part no. 176021-104) 178120-206 .375-Inch PCB Support (located between the Main and Analog Vector-Generator PCB) 178120-112 %4-Inch PCB Support 178120-212 ¥%4-Inch PCB Support

5-27

Page 67

Illustrated Parts Lists Star Wars

Information on Ireland-built game not available for first printing.

Figure 5-9B PCB Mounting Hardware Ireland-Built Cabinet

5-28

Page 68

Star Wars Illustrated Parts Lists

Information on Ireland-built game not available for first printing.

5-29

Page 69

Illustrated Parts Lists

5-30 fom

C5e + C57 0+ [To] C58} | > C69

CoOT+4645 470 pf

IHC 4b 47056 C47 4G

Col or1C48 4pt

Ce C49 42 pt Cost C50 470 pF CO4—0 Oo c52 |_| f+ C53 eZ) coo C54 C

cob-torLo}amc55

Star Wars

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific ‘Written permission of Atari, Inc., Sunnyvale, CA. This drawings only conditionally issued, and ‘neither rectipt nor possession thereof confers or transfers any right in, of license to use, the subfect matter of the drawing oF any design of technical information Shown thereon, nor an right to reproduce this drawing or any

par thereof. Except for manufacture by vendorsof Atari, I, and

for manufacture under the corporation's writtenicense, no tight

toreproduce this drawingis granted or the subjectmatter thereof

‘unless by weitten agreement with or written permission from the corporation

Figure 5-10 EMI Shield PCB Assembly A040258-01 A

Page 70

Star Wars Tlustrated Parts Lists

EMI Shield PCB Assembly Parts List

Part No. Description

Capacitors

C1-C160.1 pF, +80% -20%, 50 V, Ceramic Capacitor122002-104
C170.01 #E, +80% -20%, 25 V Minimum, Ceramic Axial-Lead Capacitor122005-103
€21-C23,0.1 gE, +80% -20%, 50 V, Ceramic Capacitor122002-104
C260.1 pF, +80% -20%, 50 V, Ceramic Capacitor122002-104
C290.1 wE, +80% -20%, 50 V, Ceramic Capacitor122002-104
C31~C340.1 pF, +80% -20%, 50 V, Ceramic Capacitor122002-104
C360.01 uF, +80% -20%, 25 V Minimum, Ceramic Axial-Lead Capacitor122005-103
€37-C400.1 4B +80% -20%, 50 V, Ceramic Capacitor122002-104
C45-C50470 pF, 100 V, Ceramic Axial-Lead Capacitor122016-471
C52-C640.1 uF, +80% -20%, 50 V, Ceramic Capacitor122002-104
C680.1 hE, +80% -20%, 50 V, Ceramic Capacitor122002104

Connectors

P1930-Pin Edge Connector (Acceptable substitute is part no. 179046-030)179073-030
P2044-Pin Edge Connector (Acceptable substitute is part no. 179046-044)179073-044

Miscellaneous Spacer 037873-02 #4-40 x % Cross-Recessed Pan-Head Screw 72-1404F ¥4-Inch Grommet 178044-242 44-Inch White Plunger 178045-442 Flat Nylon Washer 175009-221

Page 71

Hhustrated Parts Lists

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden withou« the specific written permission of Atti, Inc, Sunnyvale, CA. This drawing is only conditionally issued, and neither receipt nor possession thereof confers or transfers any right in, of license to use, the sub: ject matter of the drawing or any design or technical information shown thereon, nor any right to reprodilce this drawing or any part thereof, Except for manufacture by vendors of Aus, Inc, and for manufacture under the corporason’s written license, no right to reprodiice this drawings granted or the subject mattershereof unless By written agreement with or written permission from the corporation. Star Wars:

TIP 32 TOA2002 A TDAZ0O2A 102 _indooz Q5 Qe

CR4LL,flo

R527 0 *] BS RS

To]RAC? Geencicao

i} S31R3 ¢Gzz) oS cis) <l2 a cet ase [OS R220 oy Re id

#33288ge85470

Figure 5-11 Regulator/Audio II PCB Assembly A035435-02 G

Page 72

Star Wars Illustrated Parts Lists

Regulator/Audio II PCB Assembly Parts List

DesignatorDescriptionPart No.

Capacitors

cl470 uF, 25 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor24-250477
C20.001 wF, 35 V, Ceramic-Disc Axial-Lead Capacitor122002-102
C30.1 uF, 25 V, Ceramic-Disc Axial-lead Capacitor (Acceptable substitute is partno.29-088

122002-104

C4470 uF, 25 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor24-250477
cS.O1 WF, 25 V Ceramic-Disc Axial-Lead Capacitor (Acceptable substitute is part no.100015-103

122005-103)

C60.22 pF 25 V, Ceramic-Disc Axial-Lead Capacitor122004-224
Cc0.001 wE, 35 V, Ceramic-Disc Axial-Lead Capacitor122002-102
c80.22 wF, 25 V, Ceramic-Disc Axial-Lead Capacitor122004-224
C9, C103300 wF, 35 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor24-350338
cil0.1 uF, 25 V, Ceramic-Disc Axial-Lead Capacitor (Acceptable substitute is partno.29-088

122002-104

C12470 pF, 25 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor24-250477
C131000 pF, 25 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor24-250108
ci4-01 wE, 25 V Ceramic-Disc Axial-Lead Capacitor (Acceptable substitute is part no.100015-103

122005-103)

cis0.22 uF, 25 V, Ceramic-Disc Axial-Lead Capacitor122004-224
C160.001 uF, 35 V, Ceramic-Disc Axial-Lead Capacitor122002-102
ci70.22 wE, 25 V, Ceramic-Disc Axial-Lead Capacitor122004-224
C18, C193300 uF, 35 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor24350338
C20, C210.1 pF, 25 V, Ceramic-Disc Axial-lead Capacitor (Acceptable substitute is part no.29-088

122002-104

22, C23.1 pF, 5O V, Aluminum Electrolytic Fixed Axial-Lead Capacitor24-500105
C2422 wE, 35 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor24-350226
C3)22 uF, 35 V, Aluminum Elecvrolytic Fixed Axial-iead Capacitor24350226

Diodes

CRIType-IN4002, 1 A, 100 V Silicon Rectifier Diode31-1N4002,
cR4Type-IN4002, 1 A, 100 V Silicon Rectifier Diode31-1N4002
CR5-CR8‘Type-IN5401, 3 A, 100 V Silicon Rectifier Diode31-1N5401

Resistors

RI2700, +5%, %& W Resistor110000-271
R333.Q, +5%, % W Resistor110000-330
R4100 Q, +5%, % W Resistor110000-101
RS2.70, +5%, 1 W Resistor110009-027
RG3.9kO, +5%, 4 W Resistor110000-392
R775 kQ, £5%, 1A W Resistor110000-752
R81 kQ Vertical PCB-Mounting Cermet Potentiometer (Acceptable substitute is part19-315102

no. 119002-102)

RO2202, +5%, ¥% W Resistor110001-221

(Continued on next page)

Page 73

Illustrated Parts Lists Star Wars

Regulator/Audio II PCB Assembly Parts List, continued

DesignatorDescriptionPart No.
RIO19, +5%, 4 W Resistor110000-010
RIL102, +5%, % W Resistor110000-100
R121002, 5%, % W Resistor110000-101
R13, R1410kQ, +5%, % W Resistor110000-103
R20102, +5%, 4% W Resistor110000-100
R212200, +5%, ¥ W Resistor110001-221
RI910, +5%, 4 W Resistor110000-010
R221009, +5%, % W Resistor110000-101
R240.19, 3%, 7 W Wirewound Resistor19-100P1015
R2549, +5%, 5 W Wirewound Resistor116001-040
R27, R281kQ, +5%, 4 W Resistor110000-102
R29, R30100, +5%, 4 W Resistor110000-100
R31220, +5%, 10 W Wirewound Resistor116000-220
R32, R335.6 kM, +5%, % W Resistor110000-562

Transistors

Q2Type-TIP32 PNP Power Transistor33-TIP32
3Type-2N3055 NPN Silicon Transistor34-2N3055

Miscellaneous

Jo6 Position Connector Receptacle79-58306
J79-Position Connector Receptacle79-58308
JB4-Position Connector Receptacle79-58354
J96-Position Connector Receptacle79-58306
io12-Position Connector Receptacle79-58346
Qa5 V Linear Voltage Regulator37-LM305
Q2,Q9Thermally Conductive Silicon Insulator78-16014
Q3Thermally Conductive Silicon Insulator78-16008
Q5Audio Amp TDA2002A137151-002
Q7Audio Amp TDA2002A,137151-002
Qs‘Type-7812 +12 V Voltage Regulator37-7812
Q9‘Type-7905 -5 V Voltage Regulator37-7905

Heat Sink 034531-01 Test Point (Acceptable substitute is part no. 020670-01) 179051-001

Page 74

A038461 -21 A a 10 9 8 7 6 5 4 3 2 1 Star Wars

(= == Y= IY CBs ee Pears ec] a me = a.

er ied rT af ae Beces2 =)

Sigzag pee]

§ [toaiten i i

Bag { rac aaa ay Seas] Ses] Ses] fle 4] feel Sea)

Saad aa Tezra] | See era] iss7a ry 7a] Boke fisex) Heer) ery cerry bree] sZ4q sie a4] |

Figure 5-12 Main Printed-Circuit Board Assembly

5-35 kK Ben, ysose Saas] Sava] | STS] SSI a] Sisal] ' sae c= WES! tian tes om tem § Ws

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING

idden i IHustrated Parts Lists

Page 75

Illustrated Parts Lists Star Wars

Main Printed-Circuit Board Assembly Parts List

DesignatorDescriptionPart No.

Capacitors

cl0.1 #E, +5%, 50 V Ceramic Capacitor122002-104
C2100 pF, 100 V Mica Capacitor128002-101
C3.39 pF, 100 V Mica Capacitor128002-390
C4-C200.1 wF, +5%, 50 V Ceramic Capacitor122002-104
C45-C480.1 wE, +5%, 50 V Ceramic Capacitor122002-104
C49-C510.100 pF, 35 V Electrolytic Capacitor24-350107
C52-C920.1 pF, £5%, 50 V Ceramic Capacitor122002-104
C930.10 #F, 35 V Electrolytic Capacitor24350106
C944.7 wE, 35 V Electrolytic Capacitor124000-475
C95, C960.1 wE, +5%, 50 V Ceramic Capacitor122002-104

Diodes

CRIType-IN914 Diode31-INO14
CR2Red Light-Emitting Diode38-MV5053
CR3‘Type-INDI4 Diode31-1N914
CR4-CR6Red Light-Emitting Diode38-MV5053

Integrated Circuits

VRL5 V Fixed Regulator Integrated Circuit37-7805
OB/C3-8 Line Decoder Integrated Circuit137177001
OD/ETri-State Octal Bus Transceiver Integrated Circuit37-7ALS245
IBLine Driver/Receiver Integrated Circuit37-TALS244
1cLine Driver/Receiver Integrated Circuit37-TALS244
1ENon-Volatile RAM Integrated Circuit137288-001
IF300 ns ‘Tri-State EROM Integrated Circuit136021-101
1H300 ns Tri-State EROM Integrated Circuit136021-102
Y/K300 ns Tri-State EROM Integrated Circuit136021-103
1K/L300 ns Tri-State EROM Integrated Circuit136021-104
IM300 ns Tri-State EROM Integrated Circuit136021-106
INQuad 2-Input NOR Gate Integrated Circuit37-74804
2CMicroprocessor137249-120
2E/FLine Driver/Receiver Integrated Circuit37-74LS244
2F/H150 ns Tri-State Static RAM Integrated Circuit137211-001
2JDual 2-4 Decoder/Multiplexer Integrated Circuit37-7ALS139
2kHex Inverter Integrated Circuit37-T4LS08
2L3-8 Line Decoder Integrated Circuit137177-001
2MDual D-Ivpe Flip-Flop Integrated Circuit37-TALSTA
2N4-Bit Counter Integrated Circuit37-74LS161
2PDual 4-Bit Bin Counter Integrated Circuit37-7418393
2RDual 4-Bit Bin Counter Integrated Circuit37-74LS393
3DUp-Down Counter Integrated Circuit377418191
3EUp-Down Counter Integrated Circuit37-74LS191

(continued on next page)

5-36

Page 76

Star Wars Jilustrated Parts Lists

Main Printed-Circuit Board Assembly Parts List, continued

DesignatorDescriptionPart No.
3FUp-Down Counter Integrated Circuit37-7ALSIOL
3HQuad Data Selector/Multiplexer Integrated Circuit37-74LS157
3JData Selector/Multiplexer Integrated Circuit37-74LS153
3KData Seiector/Multiplexer Integrated Circuit37-74LS153
3LQuad Data Selector/Muitiplexer Integrated Circuit37-7ALS15S7
3MType-74LS00 Integrated Circuit37-74LS00
3NShift/Storage Register Integrated Circuit137180-001
3PQuad 2-Input NOR Gate Integrated Circuit37-7ALSO4
3R4-Bit Counter Integrated Circuit37-74LS161
4DShift/Storage Register Integrated Circuit137180-001
4E‘Tri-State Octal Bus Transceiver Integrated Circuit37-TALS245,
4FTri-State Octal Bus Transceiver Integrated Circuit37-TALS245,
4H‘Tri-State Octal Bus Transceiver Integrated Circuit37-7418245
4)Line Driver/Receiver Integrated Circuit37-7418244
4KLine Driver/Receiver Integrated Circuit37-74L8244
AL, SLOctal D-Type Flip-Flop Integrated Circuit37-7ALS374
4M, SMOctat Dype Flip-Flop Integrated Circuit37-7483 74
4N-6N,4-Bit Counter Integrated Circuit37-741883,
4P-6PQuad D‘ype Flip-Flop Integrated Circuit37-TALSI7S
5BQuad Exclusive OR Integrated Circuit37-74LS86
5C8-Bit Register Counter Integrated Circuit37-74LS164
5D8-Bit Register Counter Integrated Circuit37-74LS164
5E, GEHex Inverter Integrated Circuit37-T4LS08
SF150 ns Tri-State Static RAM Integrated Circuit137211-001
SH150 ns Tri-State Static RAM Integrated Circuit137211-001
sy8-Bit Register Counter Integrated Circuit37-74LS164
5K8-Bit Register Counter Integrated Circuit37-74LS164
5RDual 1-of-4 Decoder/Multiplexer Integrated Circuit137221-001
OA8-Bit Register Counter Integrated Circuit37-741S165,
6B8-Bit Register Counter Integrated Circuit37-74LS165
6C, 7CTwo's-Complement, Serial Multiplexer Integrated Circuit137182-001
6D, 7DShift/Storage Register Integrated Circuit137180-001
GFData Selector/Multiplexer Integrated Circuit37-74LS153,
6HUp-Down Counter Integrated Circuit37-7A1S191
gqUp-Down Counter Integrated Circuit37-74L8191
6KHex Inverter Integrated Circuit37-74LS08,
OLQuad D-Type Flip-Flop Integrated Circuit37-74LS175
6M4-Bit Counter Integrated Circuit37-74L883
ORDual D-Type Flip-Flop Integrated Circuit37-7ALSTA
7A8-Bit Register Counter Integrated Circuit37-TALSIOS
7B8-Bit Register Counter Integrated Circuit37-74LS165
JEType-74LS00 Integrated Circuit37-T4LS00
JF‘Type-74LS00 Integrated Circuit37-T4LS00
7HROM Integrated Circuit136021-110

(continued on next page)

5-37

Page 77

Star Wars Dlustrated Parts Lists

Main Printed-Circuit Board Assembly Parts List, continued

DesignatorDescriptionPart No.
RIG, RI71kQ, +5%, 4 W Resistor110000-102
R18-R21470 9, +5%, % W Resistor110000-471
R22-R251kQ, +5%, 4 W Resistor110000-102
R26-R33,4709, +5%, % W Resistor110000-471
R34-R411kQ, +5%, 4 W Resistor110000-102
R42-R5710 kQ, +5%, % W Resistor110000-103
R582209, +5%, % W Resistor110000-221
R79-R811002, +5%, 4 W Resistor110000-101
R82-R864.70, +5%, % W Resistor110000-472
ROL1509, +5%, % W Resistor110000-151
R92-R971kQ, 45%, % W Resistor110000-102
R10022k, +5%, % W Resistor110000-223

Sockets

1E18 Contact, Medium-Insertion-Force IC Socket79-42C18.
IF28 Contact, Medium-Insertion-Force IC Socket79-42C28
IHD28 Contact, Medium-Insertion-Force IC Socket79-42C28
WK28 Contact, Medium-Insertion-Force IC Socket79-42C28
1K/L28 Contact, Medium-Insertion-Force IC Socket79-42C28
1M.28 Contact, Medium-Insertion-Force IC Socket79-42C28
2C40 Contact, Medium-Insertion-Force IC Socket79-42C40
2h24 Contact, Medium-Insertion-Force IC Socket79-42C24
SF24 Contact, Medium-Insertion-Force IC Socket79-42C24
SH24 Contact, Medium-Insertion-Force IC Socket79-42C24
7H18 Contact, Medium-Insertion-Force IC Socket79-42C18
vA18 Contact, Medium-Insertion-Force IC Socket79-42C18
7K18 Contact, Medium-Insertion-Force IC Socket79-42C18
7L18 Contact, Medium-Insertion-Force IC Socket79-42C18
OK28 Contact, Medium-Insertion-Force IC Socket79-42.C28

Switches

10D8 Toggle DIP Switch66-118PIT
10E8:Toggle DIP Switch66-118PIT
ML4Toggle DIP Switch66-114PIT

Transistors

QiType-2N3904 Transistor34-2N3904
Q3, Q4‘Type-2N6044 Transistor34-2N6044

Miscellaneous Test Point Acceptable substitute is part no. 020670-01 179051-002

Ll100 pH, +5%, Fixed RF InductorAcceptable substitute is part no. 141002-00141-3003
JIGA2-Contact Header Connector79-58255,
JIGB4-Contact Header Connector79-58331
Q3Nylon Snap-In Fastener81-4302
Q4Nylon Snap-In Fastener81-4302
VRINylon Snap-In Fastener81-4302
YI12.096-MHz Crystal144000-001

5-39

Page 78

Star Wars. Illustrated Parts Lists

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING

Ny ul cca

4g feet fez ews) Saeed) ae ‘ae ae a co co rer 17211 (ara

Ser = 272A -5e! ) [evan es

Figure 5-13, Analog Vector-Generator (AVG) PCB Assembly A038463-21 A

5-40

Page 79

Star Wars

Analog Vector-Generator (AVG) PCB Assembly Illustrated Parts Lists

Parts List

DesignatorDescriptionPart No.

Capacitors

cl-C3,0.1 pF, +80% -20%, 50 V Ceramic Capacitor122002-104
C4, C50.01 uF, 100 V Mylar Capacitor21101103
C6, C7O.1 pF, +80% -20%, 50 V Ceramic Capacitor122002-104
C80.047 wF, + 10%, 50 V Polycarb Axial-Lead Capacitor122010-473
C9-Cl20.1 pE, +80% -20%, 50 V Ceramic Capacitor122002-104
cl40.1 pF, +80% -20%, 50 V Ceramic Capacitor122002-104
C17-C200.1 pF, +80% -20%, 50 V Ceramic Capacitor122002-104
C210.01 wE, 100 V Mylar Capacitor21-101103
C250.047 pF, +10%, 50 V Polycarb Axial-Lead Capacitor122010-473
C26-C280.1 pF, +80% -20%, 50 V Ceramic Capacitor122002-104
C310.1 pF, +80% -20%, 50 V Ceramic Capacitor122002-104
C35, C36Ol BE, + 80% -20%, 50 V Ceramic Capacitor122002-104
C37150 p, 100 V Minimum, Dipped, Fixed Mica Capacitor128002151
C3839 pF, 100 V Minimum, Dipped, Fixed Mica Capacitor128002-390
C39, C400.1 pF, +80% -20%, 50 V Ceramic Capacitor122002-104
C410.01 wF, 50 V Ceramic Capacitor27500103
C4210 pF, 100 V Minimum, Dipped, Fixed Mica Capacitor128002-100
C43, C44100 pF, 35 V, Aluminum Electrolytic Axial-Lead Capacitor24-350107
C4522 pF, 25 V, Aluminum Electrolytic Axial-Lead Capacitor24-250226
C46100 uF, 35 V, Aluminum Electrolytic Axial-Lead Capacitor24-350107
C47150 pF, 100 V Minimum, Dipped, Fixed Mica Capacitor128002-151
C4822 pF, 25 V, Aluminum Electrolytic Axial-Lead Capacitor24-250226
C50-C650.1 pF, +80% -20%, 50 V Ceramic Capacitor122002-104
C66150 pF, 100 V Minimum, Dipped, Fixed Mica Capacitor128002-151
67-C800.1 uF, +80% -20%, 50 V Ceramic Capacitor122002-104
C81100 pF, 35 V, Aluminum Electrolytic Axial-Lead Capacitor24-350107
C820.1 pF, +80% -20%, 50 V Ceramic Capacitor122002-104
C8322 pF, 100 V Minimum, Dipped, Fixed Mica Capacitor128002-220

Coils

LI-L3830 mA, 0.290, +10%, 1.0 wH, Peaking Coil Inductor141007-001

Diodes

CRIType-IN914 Diode31-1N914
CR2Type-MV5053 Red LightEmitting Diode38-MV5053
CR3, CR4Type-1N100 Diode31-1N100

Integrated Circuits

1AQuad 2-Input AND Gate Integrated Circuit37-T4LS08
1B4-Bit Counter Integrated Circuit37-74LS161
1c4-Bit Counter integrated Circuit37-7ALS161
1D4-Bit Counter Integrated Circuit37-74LS161
IEQuad 2-Input NOR Gate Integrated Circuit37-74LS02
IF‘Triple 3-Input NOR Gate Integrated Circuit3 7-TALS27
1HDual D-Type Flip-Flop Integrated Circuit37-7ALSTA
1KTri-State Octal Bus Transceiver Integrated Circuit37TALS245

(continued on next page)

5-41

Page 80

Illustrated Parts Lists Star Wars

Analog Vector-Generator (AVG) PCB Assembly Parts List, continued

DesignatorDescriptionPart No.
ILRead-Only Memory Integrated Circuit136021-105
1MLine Driver/Receiver Integrated Circuit37-T4LS244
INLine Driver/Receiver Integrated Circuit37-7418244
IPLine Driver/Receiver Integrated Circuit37-T4LS244
24Dual 4-Input NAND Gate Integrated Circuit37-7A1S20
2B4-Bit Counter Integrated Circuit37-7ALSI61
2CTriple 3-Input Positive AND Gate Integrated Circuit137149-001
2DDual Type Flip-Flop Integrated Circuit37-74LS74
2Quad 2-Input OR Gate Integrated Circuit37-7A1S32
2FDual J-K Flip-Flop Integrated Circuit37-74109
2HQuad 2-Input AND Gate Integrated Circuit37-74LS08
2JVector-Generator Integrated Circuit137179-001
2K4to 10 Decoder Integrated Circuit37-T4L842
2MLine Driver/Receiver integrated Circuit37-T4LS244
2NLine Driver/Receiver Integrated Circuit37-TALS244
3AQuad 2-Input NAND Gate Integrated Circuit37-T4LS800
3BHex D:Iype Flip-Flop Integrated Circuit37-7ALSI7A
3cQuad D{Type Flip-Flop Integrated Circuit37-74L8175,
3D4 to 10 Decoder Integrated Circuit37-T41S42
3EQuad 2-Input NOR Gate integrated Circuit37-74802
3F748260 Integrated Circuit37-748260
3HQuad 2-Input NOR Gate Integrated Circuit37-7ALSO2
3L150 ns Tri-State Static RAM Integrated Circuit137211-001
3M150 ns Tri-State Static RAM Integrated Circuit137211-001
3P150 ns Tri-State Static RAM Integrated Circuit137211-001
48Quad Data Selector/Multiplexer Integrated Circuit37-TALSIST
4BRead-Only Memory Integrated Circuit136021-109
4CQuad Data Selector/Multiplexer Integrated Circuit37-74LS157
4DHex, Schmitt/Trigger Integrated Circuit37-74L814
4EQuad 2-Input NAND Gate Integrated Circuit37-7400
4FQuad 2-Input Exclusive-OR Gate Integrated Circuit137002-001
4HQuad Dlype Flip-Flop Integrated Circuit37-74LSI75
4L150 ns Tri-State Static RAM Integrated Circuit137211-001
4L150 ns Tri-State Static RAM Integrated Circuit137211-001
4M.150 ns Tri-State Static RAM Integrated Circuit137211-001
4P150 ns Tri-State Static RAM Integrated Circuit1372\1-001
5AShift Register Integrated Circuit37-TALSI94
5BShift Register Integrated Circuit37-7ALSI94
5cShift Register Integrated Circuit37-7ALSI94
SEOctal D-lype Flip-Flop Integrated Circuit37-TALS273
5FShift Register Integrated Circuit37-74LS194
5HShift Register Integrated Circuit37-7ALSI94
SJQuad 2-Input OR Gate Integrated Circuit37-T4LS32
5KDual D-lype Flip-Flop Integrated Circuit37-74874

5-42 (continued on next page)

Page 81

Star Wars Illustrated Parts Lists

Analog Vector-Generator (AVG) PCB Assembly Parts List, continued

DesignatorDescriptionPart No.
SLQuad DType Flip-Flop Integrated Circuit37-74LS175
5MQuad D-Type Flip-Flop Integrated Circuit37-7ALS175,
5PHex Inverter Integrated Circuit37-74S04
6A/B12-Bit D-A Converter, Integrated Circuit137158-002
6D8-Bit D-A Converter, Integrated Circuit137159-001
6E12-Bit D-A Converter, Integrated Circuit137158-002
OFOctal D‘Type Flip-Flop Integrated Circuit37-74L8273
6HShift Register Integrated Circuit37-74LS194
gTriple 3-Input NAND Gate Integrated Circuit137236-001
6KHex Inverter Integrated Circuit37-74L804
6LQuad D‘Type Flip-Flop Integrated Circuit37-7ALSI75
6MUp/Down Counter Integrated Circuit37-TALSIOL
7ADual Operational Amplifier Integrated Circuit37TLO82CP
7BLF13201 Quad Analog Switch, Integrated Circuit3713201
7DDual Operational Amplifier Integrated Circuit37-TLO82CP
JELF13201 Quad Analog Switch, Integrated Circuit3713201
8BICDual Operational Amplifier Integrated Circuit37TLO82CP
8F8-Bit D-A Converter, Integrated Circuit137159-001
8LHex Buffer/Driver Inverter Integrated Circuit37-7407
8MQuad 2-Input NOR Gate Integrated Circuit37-74LS02
8N8-Bit Register Counter Integrated Circuit37-74LS164
9BICDual Operational Amplifier Integrated Circuit37-TLO82CP
OFDual Operational Amplifier Integrated Circuit37TLOS2CP
VRI1A, 15 V, Fixed Regulator Integrated Circuit37-7815,
VR21A, -15 V, Fixed Regulator Integrated Circuit37-7915,

Resistors

RI-R10.10kQ, 45%, % W Resistor110000-103
RIL12k@, +5%, % W Resistor110000-123
RI224kQ, +5%, 4 W Resistor110000-243
R1347 kQ, +5%, Vs W Resistor110000-473
Ri48200, +5%, 4 W Resistor110000-821
RI5150 kQ, +5%, %& W Resistor110000-154
RIG12 kQ, +5%, 4 W Resistor110000-123
RI76.2 kQ, 5%, %& W Resistor110000-622
R20-R224700, +5%, %& W Resistor110000-471
R23-R254.7kQ, +5%, % W Resistor110000-472
R268200, +5%, 4 W Resistor0000-821
R278200, +5%, % W Resistor110000-821
R30, R3175 kQ, +1%, % W Resistor110003-752
R4110 kQ Potentiometer119002-103,
R42150 kQ, +5%, 4 W Resistor110000-154
R43,2.7kQ, +5%, % W Resistor110000-272
R4410 kQ Potentiometer119002-103
R4568kO, +5%, % W Resistor110000-682
RAG.22kQ, +5%, %& W Resistor110000-223,
R472 kQ Potentiometer119002-202

(continued on next page)

5-43

Page 82

Hlustrated Parts Lists

Analog Vector-Generator (AVG) PCB Assembly Parts List, continued Star Wars

DesignatorDescriptionPart No.
R51100 2, +5%, %& W Resistor110000-101
R548202, +5%, 4 W Resistor110000-821
R558202, +5%, 4 W Resistor110000-821
R5875 kQ, 21%, % W Resistor110003-752
ROB10 k@ Potentiometer119002-103
R69150 kQ, +5%, % W Resistor110000-154
RI2.7kQ, +5%, 4 W Resistor110000-272
R7110 kQ Potentiometer119002-103
R726.8kQ, 45%, %& W Resistor110000-682
R7322 kO, +5%, 4 W Resistor110000-223,
R742 k® Potentiometer119002-202
R75, R761.3 k®, +1%, % W Resistor110000-132
R781002, +5%, % W Resistor110000-101
R8115kQ, +5%, 4 W Resistor110000-153
R821kQ, +1%, & W Resistor110000-102
R8310kQ,5%, % W Resistor110000-103
R845600, +5%, % W Resistor110000-561
R85, R8675 kQ, +1%, % W Resistor110003-752
R876.19 kQ, +1%, % W Resistor110003-622
R88200 @ Potentiometer119002-201
R897.5 kQ, +1%, & W Resistor0003-752
R901002, 45%, %& W Resistor110000-101
ROL6.19 kQ, +1%, & W Resistor0003-622
R92200 Q Potentiometer119002-201
ROB7.5 kQ, +1%,W Resistor110003-752
R941002, +5%, % W Resistor110000-101
ROS, ROG75 kQ, +1%, & W Resistor110003-752
ROT3.9kQ, +5%, 4 W Resistor110000-392
R98-R105100 kQ, +5%, % W Resistor110000-104
R1067.5 kQ, +1%, % W Resistor110003-752
R1071502, 45%, % W Resistor110000-151
R1I09-R1111kQ, +1%, % W Resistor110000-102
R112, RUI3.10kQ, +5%, %4 W Resistor110000-103
RII4-R16100, +5%, % W Resistor110000-101
RU710 KO, +5%, % W Resistor110000-103
RVI, RV28 V Variable Resistor110004-001
VRI, VR2Nylon Snap-In Fastener81-4302

Sockets

IL24 Contact, Medium-Insertion-Force IC Socket79-42C24
2y40 Contact, Medium-Insertion-Force IC Socket79-42C40
3L24 Contact, Medium-Insertion-Force IC Socket79-42C24
3M24 Contact, Medium-Insertion-Force IC Socket79-42C24
3P24 Contact, Medium-Insertion-Force IC Socket79-42C24
4L24 Contact, Medium-Insertion-Force IC Socket79-42C24
4M24 Contact, Medium-Insertion-Force IC Socket79-42C24
4p24 Contact, Medium-Insertion-Force IC Socket79-42C24

Transistors

a‘Type-2N3904 Transistor34-2N3904
Q4-Q7‘Type-2N3904 ‘Itansistor34-2N3904
Q8‘Type-2N3906 Transistor34-2N3906

Miscellaneous ‘Test Point 179051-002

5-44

Page 83

Star Wars Illustrated Parts Lists

e)

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific written permission of Atari, Inc, Sunnyvale, CA. This drawing is only conditionally issued, and neither receipt nor possession thereof confers or transfers any right in, or license 10 use, the subject matter of the drawing or any design or technical information Shown thereon, ior any right to reproduce this drawing or any pat thereof, Except for manufacture Dy vendors of Ata, Inc. and for manufacture under the corporation's written license, no right 2 to reproduce this drawing isgranted or the subject matter thereof = unless by written agreement with or written permission from the i corporation, rev [a] MADE IN U.S.A.

a+ cso TT aL STAR WARS SOUND BD.

Mari ©1983 3588 ite

Figure 5-14 Sound PCB Assembly, A040260-01 A

5-45

Page 84

Illustrated Parts Lists Star Wars

Sound PCB Assembly Parts List

DesignatorDescriptionPart No.

Capacitors

cl-ci20.1 #E, 50 V, Ceramic Capacitor122002-104
C13-C15100 nF, 35 V, Aluminum Electrolytic Capacitor24-350107
C16-C200.1 pE, 50 V, Ceramic Capacitor122002-104
C22-C280.1 #E, 50 V, Ceramic Capacitor122002-104
291000 pE, 50 V, Monolithic Ceramic Capacitor122002-102
€30-C320.1 zB 50 V, Ceramic Capacitor122002-104
C331000 pF, 50 V, Monolothic Ceramic Capacitor122002-102
C340.1 pE, 50 V, Ceramic Capacitor122002-104
C351000 pF, 50 V, Monolothic Ceramic Capacitor122002-102
€36-C380.1 2E, 50 V, Ceramic Capacitor122002-104
C391000 pF, 50 V, Monoiothic Ceramic Capacitor122002-102
C40-C430.1 pE, 50 V, Ceramic Capacitor122002-104
C440.01 wv, 25 V, Ceramic Capacitor122005-103
C450.1 pE, 50 V, Ceramic Capacitor122002-104
C460.0027 pF, 50 V, Ceramic Capacitor122015-272
C47100 #F, 35 V, Aluminum Electrolytic Capacitor24-350107
C48-C500.0027 pF, 50 V, Ceramic Capacitor122015-272
C510.47 p¥, 50 V, Aluminum Electrolytic Axial-Lead Capacitor124001-474
C5210 pF, 25 V, Aluminum Electrolytic Capacitor24-250106
C53100 pF, 35 V, Aluminum Electrolytic Capacitor24350107
C54, C550.1 ¢F, 50 V, Ceramic Capacitor122002-104
C56-C580.0027 uF, 50 V, Ceramic Capacitor122015-272
C59-C610.1 pF, 50 V, Ceramic Capacitor122002-104

Connectors

P24-Contact Header-Connector179165-004
P32-Contact Header-Connector179165-002

Diodes

DSIType-MV5053 Red Light-Emitting Diode38-MV5053

Integrated Circuits

1c/DSpeech Synthesizer Integrated Circuit137308-001
1EV/O and Internal Timer Memory Integrated Circuit90-6018
1E/H150 ns Tri-State Static RAM Integrated Circuit137211-001
1HROM Integrated Circuit136021-108
WKROM Integrated Circuit136021-107
2BQuad Operational Amplifier Integrated Circuit37347
2DAudio Integrated CircuitCO12294-01
2FType-74C04 Integrated Circuit137309-001
2HType-74LS04 Integrated Circuit37741804
2aType-74LS139 Integrated Circuit37-74LS139
3A‘Type-556 Integrated Circuit37-556
3B512 Delay Line Integrated Circuit137310-001

(continued on next page)

5-46

Page 85

Star Wars Illustrated Parts Lists

Sound PCB Assembly Parts List, continued.

DesignatorDescriptionPart No.
3cQuad Operational Amplifier Integrated Circuit37-347
3DAudio Integrated Circuit€012294-01
3F‘Type-74LSI61 Integrated Circuit37-7AISI61
3H‘Type-74LS00 Integrated Circuit37-74LSO0
3Type-74LS139 Integrated Circuit37-74L8139
3KMicroprocessor137249-120
4cQuad Operational Amplifier Integrated Circuit37347- TLOBY
4DAudio Integrated CircuitC012294-01
sDAudio Integrated Circuit€012294-01
SFType-74LS161 Integrated Circuit37-7ALSI61
SHHType-74LS125 integrated Circuit137317-001
SHType-74LS74 Integrated Circuit37-74LS74
J‘Type-74L8374 Integrated Circuit37-74LS374
5K‘Type-741S374 Integrated Circuit37-7ALS374

Resistors

RI1k@, +5%, % W Resistor110000-102
R2, R310kQ, +5%, % W Resistor110000-103
R41kQ, +5%, % W Resistor110000-102
R5, RG10kQ, +5%, % W Resistor110000-103
R71502, +5%, 4 W Resistor110000-151
RIO10kQ, +5%, 14 W Resistor110000-103
Rul3.3kQ, +5%, 4 W Resistor110000-332
RI21kQ, +5%, % W Resistor110000-102
RB10kQ, +5%, 4 W Resistor110000-103,
RI43.3 kQ, +5%, % W Resistor110000-332
RIS1kQ, £5%, 4 W Resistor110000-102
RIG3.3kQ, +5%, % W Resistor0000-332
RIT10kQ, +5%, % W Resistor110000-103
RIS.18k, 25%, % W Resistor110000-182
RID100 kQ, £5%, % W Resistor110000-104
R201kQ,£5%, % W Resistor110000-102
R2147kQ, 5%, 4 W Resistor110000-473
R221kQ, +5%, %& W Resistor110000-102
R2347 kQ, £5%, 4 W Resistor110000-473
R241kQ, +5%, % W Resistor110000-102
R25,82 kM, 45%, % W Resistor110000-823
R261kQ, +5%, 14 W Resistor110000-102
R2782 kQ, 45%, % W Resistor110000-823
R28100 kQ, 5%, 14 W Resistor110000-104
R2915kQ, +5%, % W Resistor110000153,
R3012 kM, +5%, 4 W Resistor110000-123,
R31, R32560 kQ, +5%, % W Resistor110000-564
R33, R344.7kQ, £5%, % W Resistor110000-472

(continued on next page)

5-47

Page 86

Illustrated Parts Lists Star Wars

Sound PCB Assembly Parts List, continued

DesignatorDescriptionPart No.
R35,2.2kQ, +5%, 4 W Resistor110000-222
R36150, +5%, % W Resistor110000-150
R3710 kQ, +5%, 4 W Resistor110000-103
R384700, +5%, % W Resistor110000-471
R39, R4012 kQ, +5%, % W Resistor0000-123
R4168kO, +5%, 4 W Resistor110000-683
R4212 kQ, +5%, 4 W Resistor110000-123,
R43,15kQ, +5%, 4 W Resistor110000-152
RI4100 2, +5%, %4 W Resistor110000-101
R45,470 kQ, +5%, 4 W Resistor110000-474
R46, R4712kQ, +5%, 4 W Resistor110000-123
R48, R4922 kQ, +5%, % W Resistor110000-223,
R5047kQ, +5%, % W Resistor110000-473
R512.2kQ, +5%, 4 W Resistor110000-222
R52, R5322 kQ, +5%, 4 W Resistor110000-223
R54, R5547kQ, 5%, '4 W Resistor110000-473
R562.2kQ, +5%, %4 W Resistor110000-222

Sockets

1c/D28-Contact, Medium-Insertion-Force Integrated Circuit Socket79-42C28
1E40-Contact, Medium-Insertion-Force Integrated Circuit Socket79-42C40
1R/H24-Contact, Medium-Insertion-Force Integrated Circuit Socket79-42C24
1H28-Contact, Medium-insertion-Force Integrated Circuit Socket79-42C28
YK28-Contact, Medium-Insertion-Force Integrated Circuit Socket79-42C28
2D40-Contact, Medium-Insertion-Force Integrated Circuit Socket79-42C40
3D40-Contact, Medium-Insertion-Force Integrated Circuit Socket79-42C40
3K40-Contact, Medium-Insertion-Force Integrated Circuit Socket79-42C40
4D40-Contact, Medium-Insertion-Force Integrated Circuit Socket79-42C40
5D40-Contact, Medium-Insertion-Force Integrated Circuit Socket79-42C40

Transistors

QI, Q2Type-2N3906 Transistor33-2N3906
Q3, Q4Type-2N3904 Transistor34-2N3904

Miscellaneous

TPI-TP12‘Test Point179051-002

5-48

Page 87

Star Wars

AC Alternating current; from zero it rises to a maximum positive level, then passes through zero again to a maximum negative level. ACTIVE STATE ‘The true state ofa signal, For example: The active state for START is low.

ADDRESS A value that identifies a specific location of data in memory; normally expressed in hexadecimal notation. ANALOG Measurabie in an absolute quantity (as opposed to on or off). Analog devices are volume controls, light dimmers, stereo amplifiers, etc. ANODE The positive (arrow) end of a diode. AMPLIFIER A device used to increase the strength of an applied signal. AMPLITUDE The maximum instantaneous value of a waveform pulse from zero. ASTABLE Having no normal state. An astable device will free-run or oscillate as long as operating voltage is applied. The oscil- Jation frequency is usually controlled by external circuitry. AUXILIARY COIN SWITCH Amomeniary-contact pushbutton switch with a black cap located on the utility panel. The auxiliary coin switch adds credits to the game without activating a coin counter. BEZEL A cut, formed, or machined retention device, such as the conical device used. to mounta pushbutton switch to 4 control panel, or the formed device used to frame the video display screen. BIDIRECTIONAL Able to send or receive data on the same line (e.g., the data bus of a microprocessor). BINARY Anumber system that expresses ail values by using ewo digits (0 and 1). BIT A binary digit; expressed as 1 or 0. BLANKING Turning off the beam on a cathode-ray tube during retrace. Glossary

Glossary of Terms

BLOCK DIAGRAM A drawing in which functional circuitry units are represented by blocks. Very useful during initial troubleshooting. BUFFER

  • An isolating circuit designed to eliminate the reaction of a driven circuit on the circuits driving it (e.g.,a buffer amplifier).
  • A device used to supply additional drive capability. BUS An electrical path over which information is transferred from any of several sources to any of several destinations. CAPACITOR A device capable of storing electrical energy. A capacitor blocks the flow of DC current while allowing AC current to pass. CATHODE The negative end ofa diode. CHIP An integrated circuit comprising many circuits on a single wafer slice. CLOCK Acepetitive timing signal for synchronizing system functions. COINCIDENCE Occurring at the same time. COIN COUNTER A 6-digit electromechanical device that counts the coins inserted in the coin mechanism(s). COIN MECHANISM A device on the inside of the coin door that inspects the coin to determine if the correct coin has been inserted. COMPLEMENTARY Having opposite states, such as the outputs of a flip-flop. COMPOSITE SYNC Horizonal and vertical synchronization pulses that are bused together into a single signal. This signal provides the timing necessary to keep the display in synchronization with the game circuitry. COMPOSITE VIDEO Complete video signal from the game system to drive the display circuitry, usually comprising H SYNC, V SYNC, and the video. CREDIT One play for one person based on the game switch settings. CRT Cathode-ray tube. DATA General term for the numbers, letters, and symbols that serve as input for device processing. DARLINGTON A two-transistor amplifier that provides extremely high gain. DC Direct current, meaning current flowing in one direction and of a fixed value. DEFLECTION YOKE Electromagnetic coils around the neck of 2 cathode-ray tube. One set of coils deflects the electron beam horizontally and the other set deflects the beam vertically. DIAGNOSTICS A programmed routine for checking Circuitry. For example: the self-test is a diagnostic routine. DIODE A semiconductor device that conducts in only one direction. DISCRETE Non-integrated components, such as resistors, capacitors, and transistors. DMA Direct memory access. DMA is a process of accessing memory that bypasses the microprocessor logic. DMA. is normally used for transferring data between the input/output ports and. memory. DOWN TIME The period during which a game is malfunctioning or not operating correctly due to machine failure. EAROM Electrically alterable read-only memory (see ROM), The EAROM is a memory that can be changed by the application of high voltage. FLYBACK A‘step-up transformer used in a display to provide the high voltage. GATE
  • A circuit with one output that responds only when a certain combination of pulses is present at the inputs.
  • A circuit in which one signal switches another signal on and off.
  • To control the passage of a pulse or signal.

git

Page 88

Glossary

HARNESS A prefabricated assembly of insulated wires and terminals ready to be attachedto a piece of equipment. HEXADECIMAL Anumber system using the equivalent of the decimal number 16 as a base. The symbols 0-9 and A-F are usually used.

IMPLODE To burst inward; the inward collapse of a vacuum tube. 1/0 Input/Output. IRQ Interrupt request. IRQ is a control signal to the microprocessor that is generated by external logic. This signal tells the microprocessor that external logic needs attention. Depending on the program, the processor may or may not respond. LED The abbreviation for a light-emitting diode. LOCKOUT COIL Directs coins into the coin return box when there is no power to the game.

LOGIC STATE The binary (1 or 0) value at the node of a logic element or integrated circuit during a particular time. Also called the logic level. The list below shows the voltage levels corresponding to the logic states (levels) ina TTL system. Logic 0, Low = 0 VDC to +0.8 VDC Grey Area (Tri-State Level) = +0.8 VDC to +2.4 VDC Logic 1, High = +2.4 VDC to +5 VDC MULTIPLEXER A device that takes several low-speed inputs and combines them into one high-speed data stream for simultaneous transmission ona single line. NMI Non-maskable interrupt. NMI isa request for service by the microprocessor from external logic. The microprocessor cannot ignore this interrupt request. PAGE Asubsection of memory. A read-only memory device (see ROM) is broken into discrete blocks of data. These blocks are called pages. Each block has X number of bytes. PCB ‘fhe abbreviation for a printed-circuit board.

gl2 PHOTOTRANSISTOR A transistor that is activated by an external light source. POTENTIOMETER

  • A resistor that has a continuously moving contact which is generally mounted on a moving shaft. Used chiefly as a voltage divider. Also called a pot (slang).
  • An instrument for measuring a voltage by balancing it against a known voltage. RAM Random-access memory, A device for the temporary storage of data. RASTER-SCAN DISPLAY A display system whereby images are displayed by continuously scanning, the cathode-ray cube horizontally and vertically with an electron beam. The display system controls the intensity of the electron beam. RETRACE Ina raster-scan display, retrace is the time during which the cathode-ray tube electron beam is resetting either from right to left or from bottom to top. RESISTOR A device designed to have a definite amount of resistance. Used in circuits to limit current flow or to provide a voltage drop. ROM Read-only memory. A device for the Permanent storage of data. SIGNATURE ANALYSI: A process of isolating digital logic faults at the component level by means of special test equipment called signature analyzers. Basically, signature analyzers (e.g., the ATARI® CAT Box) convert lengthy bit streams into four-digit hexadecimal signatures. The signature read by the analyzer at each circuit node is then compared with the known good signature for that node. This process continues until a fault is located. TROUBLESHOOT The process of locating and repairing a fault.

VECTOR A line segment drawn between specific Xand Y coordinates ona cathode-ray tube.

Star Wars

‘WATCHDOG A counter circuit designed to protect the microprocessor from self-destruction if a program malfunction occurs. If amalfunction does occur, the counter applies continuous pulses to the reset line of the microprocessor, which causes the microprocessor to keep. resetting. X-Y DISPLAY A display system whereby images are displayed with vectors. ZENER DIODE A special diode used as a regulator. Its main characteristic is breaking down at a specified reverse-bias (Zener) voltage.

Page 89

TM-225 4st printing

YOUR COMMENTS, PLEASE!

Your comments will assist Atari in improving our publications. The comments are an important part of preparing for revisions of game manuals. Please write in the space below. No postage stamp is necessary if mailed in the U.S.A.

If you have any technical questions about certain ATARI games products, or are requesting additional publications, we will immediately forward your note to the appropriate person.

Page: Comments:

Fill in if you wish a reply:

Name

Firm O Distribuzor

Address 0 Operator

City State Zip O Other

Area Code Phone

Page 90

First Fold

No postage necessary if mailed in the United States

USINESS REPLY MAIL

FIRST CLASS PERMIT NO. 1004 SUNNYVALE, CA

POSTAGE WILL BE PAID BY ADDRESSEE

Atari, Inc. Attn.: Field Service/Coin-Op Division P.O. Box 427 Sunnyvale, California 94086

a8pa spp ade,

Page 91

TM-225, 4st printing

YOUR COMMENTS, PLEASE!

Your comments will assist Atari in improving our publications. The comments are an important part of preparing for revisions of game manuals. Please write in the space below,

If you have any technical questions about certain ATARI games products, or are requesting additional publications, we will immediately forward your note to the appropriate person.

Page: Comments:

Fill in if you wish a reply:

Name

Firm. O Distributor Address _ O Operator

City Country O Other

Phone: Country Code__________ Local Number

Page 92

First Fold

Atari Ireland Limited Attn.: Field Service/Coin-Op Division

Tipperary Town, Ireland

ror

a8pa spp adey,

Page 93

Seller warrants that its printed-circuit boards and parts thereon are free from defects in material and workmanship under normal use and service for a period of ninety (90) days from date of at. Seller warrants that its video displays (in games supplied with displays) are free from material and workmanship under normal use and service for a period of thirty (30) days from date of shipment, None of the Seller's other products or parts thereof are warranted, If the products described in this manual fail to conform to this warranty, Seller's sole liability shall be, at its option, to repair, rer , of credit Buyer's account for such products which are returned to Seller during said warranty period, provided:

  • Seller is promptly notified in writing upon discovery by Buyer that said products are defective; (b)Such products are returned prepaid to Seller's plant; and
  • Seller's examination of said products discloses to Seller's satisfaction that such alleged defects existed and were not caused by accident, misuse, neglect, alteration, improper repair, installation, or improper testing. In no event shall Seller be liable for loss of profits, loss of use, incidental or consequential damages, Except for any express warranty set forth in a written contract between Seller and Buyer which contract supersedes the terms herein, this warranty is expressed tn lieu of all other warranties expressed or implied, including the implied warranties of merchantability and fitness for a particular purpose, and of all other obligations or liabilities on the Seller's part, and it neither assumes nor authorizes any other person to assume for the Seller any other liabilities in connection with the sale of products by Seller,

The use of any non-Atari parts may void your warranty, according to the terms of the warranty. The use of any non-Atari parts may also adversely affect the safety of your game and cause injury to you and others, Be very cautious in using non-Atari-supplied components with our games, in order to insure your safety, Atari distributors are independent, being privately owned and operated, In their judgment they may sell parts Or accessories other than Atari parts or accessories. Atari cannot be responsible for the quality, suitability or safety of any non-Atari part or any modification including labor which is performed by such distributor.

Page 94

ATARI, INC. a 790 SYCAMORE DRIVE:,".” . P.O. BOX 906 “MILPITAS, CALIFORNIA 95035 408/942-3300 © TELEX 35-7488