Super Pac-Man (General Instructions) (Bad Scan)
Super Pac-Man (Namco, 1982) · Manual · 57 pages · 57 sections · original scan
a - = —~ oe en |
SUPER PAC-MAN
General Instructions
Ciilly MIDWAY MFG. CO.
GENERAL INSTRUCTIONS
FoR
SUPER PAC-MAN
INSTALLATION
- Unlock and open the coin box door.
- Remove four (4) "CABINET LEVELING LEGS" from inside the coin box.
- Tip the cabinet to the side and remove the shipping cleats from its bottom.
° Locate the threaded holes - one in each corner - and install the "CABINET LEVELING LEGS" in them. ‘
° Level the cabinet.
° When finished, the cabinet should be stable in the upright position.
4, Plug the game into a standard A.C. wall outlet ONLY .
Game MUST be properly grounded.
- The power ON/OFF switch is located:
° UPRIGHT MODEL: On top of the cabinet toward the back.
° COCKTAIL TABLE MODEL: Underneath the cabinet on Player No. 2's side.
LINE VOLTAGE SAFETY INTERLOCK SWITCHES
Line voltage SAFETY INTERLOCK SWITCHES have been provided for your protection. The locations of these SAFETY INTERLOCK SWITCHES are:
- UPRIGHT MODEL: Inside the rear of the cabinet on the right side of the rear access door.
- COCKTAIL TABEL MODEL: Inside the cabinet on the hinge side of the coin door.
PART NO. MO051-00316-A011
When the cabinet access door(s) are secured in place, the SAFETY INTERLOCK SWITCH plunger(s) are in a fully depressed condition. The game circuit can function normally.
When any cabinet access door(s) are opened, the SAFETY INTERLOCK SWITCH plunger(s) are in a partially extended condition. This isolates the game circuit from the line voltage. To restore power to the game circuit with the access door(s) open, gently pull the SAFETY INTERLOCK SWITCH plunger(s) out to the fully extended condition. THIS IS TO BE USED FOR
SERVICING THE GAME ONLY!
SELF-TEST
Slide switches are provided to make the game run a "Self-Test" on itself. The SELF-TEST SWITCHES are located on a mounting bracket on the inside left hahd side of the coin door.
When in the Self-Test mode, the monitor screen will display the results of certain test functions it has run on itself. (These will be discussed in more detail later.)
TO SERVICE THE CONTROL PANEL(S)
- UPRIGHT MODEL:
° The control panel is held in place by three latches, one on the left side, one on the right side, and one in the center of the front of the cabinet.
They are spring loaded to provide constant positive pressure on their latch plates.
They can be reached through the coin door AFTER turning power to the game off.
To release the latches, lift up and toward the center of the control panel. Once they are released, unhook them from their latch plates.
To remove the control panel: 7
Raise it up and tilt it toward you until you can see the cable behind it. Cradling the control panel between ‘yourself and thé cabinet, disconnect it. from its cabling and nylon retaining strap.
The control panel is now free and can be removed.
° To reinstall the control panel(s), reverse this procedure.
- COCKTAIL TABLE MODEL:
° Each control panel is held in place by several screws, two on the inside of the cabinet and three along the bottom edge of the control panel.
Turn the power off to the game.
Open the coin box door and release the two latches on the inside of the cabinet up next ‘to the table top.
Once they're released, unhook them from their latch plates.
Grasp the table top in the center above the coin door lifting up and to the side to tilt it open.
Remove the screws which secure the control panel in place.
To remove the control panel(s):
Disconnect it from its cabling. ©
The control panel is now free and can be removed.
° To reinstall the control panel(s), reverse this procedure.
-- REMOVAL OF THE MAIN-DISPLAY-GLASS AND/OR THE T.V. BEZEL ASSEMBLY
r
- UPRIGHT MODEL:
2.
° Turn the power to the game off and remove the control panel. This frees the main-display-glass so it can be lifted up.
° By putting your finger in the hole in the middle of the main-display-glass support, you can Lift it up and out. .
® Loosen the screws which secure the T.V. bezel-glass-clamps in place. Move the clamps to the side and the bezel glass may be removed. .
Remove the above mentioned‘ screws and the bezel with four bezel-glass-clamps may be removed. ;
° To reinstall the T.V. bezel asssembly and the main-display-glass, reverse this procedure.
COCKTAIL TABLE MODEL:
Remove the screws which secure the table top glass clamps in place.
Remove the table top glass.
Loosen the screws which secure the T.V. bezel-glass-clamps in place.
Move the clamps to the side and the bezel glass may be removed.
Remove the screws which secure the bezel assembly to the table top and the bezel with four bezel-glass-clamps may be removed.
To reinstall the T.V. bezel assembly and the table top glass, reverse. this procedure.
VOLUME CONTROL POT
The volume control pot is located on the C.P.U. board. The other board is the Video board. There is only one pot. For adjustment, it may be reached through the rear access door on the UPRIGHT models. On the COCKTAIL TABLE models, you will have to open the table top to reach it. To make the sounds louder, turn the pot clockwise as you face it (—).
To make the sounds less loud, turn the pot counterclockwise as you face it (4).
VOLTAGE CONTROL POT
The voltage control pot is located on the Power Supply P. C. Board. It is pre-set at the factory and SHOULD NOT be tampered with at all unless the distributors service department is contacted first.
SELF-TEST
The Self-Test mode is a special mode for checking game switches and computer functions. It is the easlest and best way to check for proper operation of the entire game. .
You may begin a Self-Test at any time after the power to the game is or by sliding the Self- Test switch to the "ON" position. Now that the game is in the Self-Test mode, it will act as follows: ,
° First, you will see a moving multicolored pattern appear on the screen.
° Immediately following this, a rightside up test display is shown on the monitor screen. The game will remain In this Self-Test mode until you set the Self-Test switch back to the "OFF" position. This test display is shown below.
=5-
SELF - TEST DISPLAY
RAM OK ROM OK 1/0 OK TABLE. . 1ST COIN 1 CREDIT _ : 2ND COIN 1 CREDIT PAC-MAN 3. RANK 8 = SOUND 00 . 1ST BONUS FOR 30000 PTS 2ND BONUS FOR 100000 PTS
, RAM TEST INDICATIONS AND THEIR MEANINGS
INDICATION MEANING CHIP LOCATION
| ey | RAM~ OK | NO RAM ‘IS OUT OF ORDER | . | |
| RAM 1 | RAM 1 on VIDEO PCB is no good | 2E | ||
| RAM 2 | RAM 2 on VIDEO PCB is no good | 2H | ||
| RAM” 3 | RAM 3 on VIDEO PCB is no good | 2K | ||
| - | RAM 4 | RAM 4 on VIDEO PCB is no good | 23 | |
| RAM 5 | RAM 5 on C P U PCB is no good | 3K | ||
| RAM 6 | RAM 6 on C P U PCB is no good | 3L | ||
| - | , | RAM | RAM 7 on C P U PCB is no good | 20 |
ROM JEST INDICATIONS AND THEIR MEANINGS
INDICATION MEANING CHIP LOCATION
NO ROM IS OUT OF ORDER
| ROM 1 | ROM 1 on C P U PCB is no .good | 1c | |
| Ee | ROM 2 | ROM 2 on C P U PCB is no good | 1B |
| ROM 3 | ROM 3 on C P U PCB is no good | 1K | 3 |
1/0 TEST INDICATIONS AND THEIR MEANINGS
INDICATION MEANING
CHIP LOCATION
NO BIT IS OUT OF ORDER BITC PU 1 Is out of order BITC PU 2 is out of order i 1/0 1 -1/0 2 a4
° If a bad ROM or RAM chip Is found by the games internal check system during the Self- Test, the game indicates this to you by showing the P.C. Board location code of the bad chip(s) in place of the letters "OK":
° To check your game function switches and buttons (coin counter switches, SUPER SPEED Button, 1 PLAYER and 2 PLAYER buttons, etc.): activate each one while the game is in the Self-Test mode. You should hear a game sound for each button or switch activated.
“=.
If you do not hear it, the switch/button is either not working, miswired, or disconnected. Check it out thorough ly.
° "RANK" is a difficulty setting, with "RANK 1" being the least difficult level of play and "RANK B" being the most difficult level of play. "RANK AUTO"; at these settings the game measures the players skill level and progressively gets harder as the player gets better. "RANK C" is the least difficult level of "AUTO" play and "RANK F" is the most difficult level of "AUTO" play. See "OPTION SWITCH SETTINGS TABLE".
° To check "SOUND":
A. Move the controller to the right momentarily and release it - "SOUND". number j changes from "00" to "01" and you hear "SOUND 01".
B. Repeat Step "A" above and "SOUND 01" will change to "SOUND 02" and it is heard.
C. Repeat Step "A" above again and "SOUND 02" changes to "SOUND 03" and it is heard and so on.
° When finished with the Self-Test mode, slide the Self-Test switch back to the "OFF" position.
A. A cross hatch pattern appears on the monitor screen for about 1 to 2 seconds.
i 8B. If you wish to keep this test pattern on the monitor screen for further use, slide { Self-Test switch to the "ON" position after the cross hatch pattern appears and before it disappears.
When finished with the cross hatch pattern, set the Self-Test switch to the "OFF" position. ;
D. Normal game functions will now return to the monitor screen.
VI Technical Troubleshooting
Introduction
The most common problems occur in harness components such as the coin acceptor, player controls, interconnecting wiring, etc. The TV monitor and PCB computer cause their share of problems too, but not as much as the harness and its component parts. TV monitor troubleshooting will not be covered here because it is covered in that section of this manual. As you already know, the PCB computer is a complex device with a number of different circuits. Some circuits remain basically the same among games, but overall there are a great many differences between them. PCB troubleshooting procedures, therefore, can be lengthy and will differ greatly among games. However, some ‘basic Z-80 CPU information is involved in this section.
General Suggestions
The first step in any troubleshooting procedure is correctly identifying the malfunction’s symptoms. This includes not only the cifcuits or features malfunctioning, but also those still operational. A carefully trained eye will pick up other clues as well. For instance, a game in which the computer functions fail completely just after money was collected may have a quarter shorting the PCB traces. Often, an experienced troubleshooter will be able to spot the cause of the problem even before opening the cabinet. After all the clues are carefully considered, the possible malfunctioning areas can be narrowed down to one or two good suspects. Those areas can be examined by a process of elimination until the cause of the malfunction is discovered.
Harness Component Troubleshooting
Typical problems falling in this category are coin and credit problems, power problems’ and failure of individual features. NO GAME CREDIT For example, your prospective player inserts his quarter and is not awarded a game. The first item to check is if the quarter is returned. If the quarter is returned, the malfunction most certainly lies in the coin acceptor itself. First, use a set of test coins (both old and new) to ascertain that the player's coin is not undersize or underweight. If your test coins are also returned, coin acceptor servicing is indicated. Generally, the cause of this particular problem is a maladjusted magnet gate. Normally, ‘this will mean slightly closing the magnet gate alittle by turning the . adjusting screw out a bit (see section on coin acceptor for more details). If the quarter is not returned and there is no game credit, the cause of the malfunction may be in one of several areas. First try operating the coin return button; if the coin is returned, the problem is most likely in the magnet gate. Enlarge the gap according to the coin acceptor service procedures. If this does not cure the problem, remove the coin acceptor, clean it and ‘perform the major adjustment procedure. If the trapped coin is not returned when the wiper lever is actuated, you may have an acceptor jammed by a slug, gummed up with beer, a jammed coin chute, or mechanical failure of the acceptor mechanism. In this case, first check for the slug that will generally be trapped against the magnet. If so, . simply remove the slug and test the acceptor. If the chute is blocked, remove the acceptor and remove the jammed coins. If there is actual failure of the acceptor, remove the unit and repair as indicated in the coin acceptor service procedures. If the coin is making .its way through the acceptor (that is, falling into the coin box), yet there is still no game credit, you either have a mechanical failure of the coin switch or electrical failure of the coin and credit circuits. The first place to begin is by checking the coin switch. Most of these switches are the make/break variety of micro switch, which is checked by testing for continuity between the NO, NC, and C terminals. When not actuated, the NC and C terminals should be continuous and the NO terminal open. When operated, the NO and C terminals should close and the NC should be open. If the coin switch checks out, examine the connections to the terminals to make sure there is good contact. If necessary, use the continuity tester and check from the terminal lug on the switch to the associated PCB trace. This will tell you if there is a continuous line all the way to the credit circuit.
DIP SWITCH SW-3 AT LOCATION SE
COINS PER CREDIT—COIN SWITCH 1 SUPER PAC-MAN OPTION SWITCH SETTINGS
DIP SWITCH SW-2 AT LOCATION 58.
DIFFICULTY LEVEL SETTINGS—“R1" IS
SUT SWZ SHES SWE SWHES SHG SWHT SWE THE EASIEST AND “RB” IS THE MOST DIFFICULT CON 1-CRET OF OF OF SWI SWH2 SWHS SHA SWHS SWHEG SWHT SWE {CON 2-CRENTS © OF OF FAMK TA" STANDARD LEVEL OF FACULTY [OFF — OFF OFF _ OFF {Con 3-CREDITS F om OF FAIR “HT EASIST LEVEL OF DIFFICULTY | ON OFF OFF OFF 1-0 6-CREDTS w OF mK AD" OF OOF OF 1c 7-CRENTS OF OF OO PAK “ES” WOOF OF 2-00 1-CREDNT Oo OF aK “BE OF OF ON OF CONS 3-CREDTS oF Oh AIK “IS” OW OF OF OF CONS 1CREDT o om oO FAM “6” GRATED LEVELS OF DIFICULT ] OFF OO OFF BONUS SUPER PAC-MEN AWARDED mK “HT WoO ON OFF AT THE FOLLOWING POINT VALUES: RAM “R8"—FACTORY SETING OF OF OF OW BGAN WITH, «BEGAN WT AUK “19” WOOF OF OW 2.08 3 SUPER PAC-MEML_5 SUPER PACEN | SWHET SWH2 SWS SWHEA SWHES SWHG SWHE7 SWE aK “RA” OF OF OW “ITSP 30000 STS PM 30000 : AK "HARDEST LEVEL OF DFFICLY | ONO OFF OW 20S PM 100000 m0 s Pv 100000 Wt OF OF CASES ATO FOL STOO 1STSPM 30000 SSP 20000 aK “RD” Ow oOF OF OW 2S Pw 80000 280 $ PM 120000 OF OF RA “RE” OF OF ON Om 1STS PM 30000 TSTSP-M 400007 ARK “RE”—-HARDEST AUTO DIFFICULTY SETTING] ON OW ON OW were Eo tae ae o.0 COINS PER CREDIT—COIN SWITCH 2 AND EVERY 80000 AND EVERY 100000 OO oO OF SWF SH? SHES SA SAS SRG ST SHED ITSP 30000 STSP-M 40000 *1-COM 1-CROIT OF OF AMD EVERY 100000. AND EVERY. 120000 OF OF OW {COM 2 CREDITS OOF ‘STS PM 30000 i] 2-CONS — 1—CREDIT OF ON AWD VERY 12000018 PAP 30000 - 7 FO 2-000 _ 3 CREDITS o_o ism om isha 40000 i a] SOUND ' wate ea som SS EE ST
DETERMINES NUMBER OF SUPER PAC-MEN 10 SOND 7
PLAYER BEGINS GAME WITH:
; SWE SHEE? SUES SHEA SHHIS SUES SWAT SWHD SCREEN 9 SUPER PAC WEN ; OF SHH SWZ SWHS SWGEA SWS SWAPS SWRHT SWE 1 SUPER PACMAN OF SORA OPERATION F 2 SUPER PACE rm FREEZE OED r 5 SUPER PACE r" *MDICATES FACTORY RECOMMEND SETTIGS PART WOMB WS -00316-60T2
A Glossary of Microprocessor Terms
MICROPROCESSOR — one or several microcircuits that perform the function of a computer's CPU. Sections of the circuit have arithmetic and comparative functions that perform computations and executive instructions. CPU — central-processing unit. A computing system's “brain”, whose arithmetic, control and logic elements direct functions and perform computations. The microprocessor section of a microcomputer is on one chip or several chips. PROM — programmable read-only memory. User permanently sets binary on-off bits in each cell by selectively fusing or not fusing electrical Jinks. Nonerasable. Used for low-volume applications.
EPROM — erasable, programmable, read-only memory. Can be erased by ultraviolet light bath, then reprogrammed. Frequently used during design and
Introduction to the
Z-80 CPU
The term “microcomputer” has been used to describe virtually every type of small computing device designed within the last few years. This term has been applied to everything from simple “microprogrammed” controllers constructed out of TTL MSI up to low end minicomputers with a portion of the CPU constructed out of TTL LSI “bit slices.” However, the major impact of the LS! technology within the last few years has been with MOS LSI. With this technology, it is possible to fabricate complete and very powerful computer systems with only a few MOS LSI components. The Zilog Z-80 family of components can be configured with any type of standard semiconductor memory to generate computer systems with an extremely wide range of capabilities. For example, as few as two LSI circuits and three standard TTL MSI packages can be combined to form a simple controller. With additional memory and I/O devices a computer can be constructed with capabilities that only a minicomputer could previously deliver. New products using the MOS LSI microcomputer are being developed at an extraordinary rate. The Zilog Z-80 component set has been designed to fit into this market through the following factors: development to get programs debugged, then replaced by ROM for mass production.
ROM — read-only memory. The program, or binary
on-off bit pattern, is set into ROM during manufacture, usually as part of the last metal layer put onto the chip. Nonerasable. Typical ROM's contain up to 16,000 bits of data to serve as the microprocessor's basic instructions. RAM — random-access memory. Stores binary bits as electrical charges in transistor memory cells. Can be read or modified through the CPU. Stores input instructions and results. Erased when power is turned off. . LSI — large scale integration. Formation of hundreds or thousands of so-called gate circuits on semiconductor chips. Very large scale integration (VLS) involves microcircuits with the greatest component density. » MOS —. metal-oxide semiconductor. A layered construction technique for integrated circuits that achieves high component densities. Variations in MOS chip structures create circuits with speed and low-power requirements, or other advantages (static will damage a MOS chip).
- The Z-80 is fully software compatible with the. popular 8080A CPU.
- Existing designs can be easily converted to include the Z-80.
- The Z-80 component set is at present superior in both software and hardware capabilities to any other microcomputer system on the market today.
- For increased throughput the Z80A operating ata 4 MHZ clock rate offers the user significant speed advantages. Microcomputer systems are extremely simple to construct using Z-80 components. Any such system consists of three parts: .
- CPU (Central Processing Unit)
- Memory .
- Interface Circuits to peripheral devices The CPU is the heart of the system. Its function is to obtain instructions from the memory and perform the desired operations. The memory is used to contain instructions and in most cases data that is to be processed. For example, a typical instruction sequence may be to read data from a specific peripheral device, store it in a location in memory, check the parity and write it out to another peripheral device. Note that the Zilog component set includes the CPU and various general purpose |/O device controllers, while a wide range of memory devices may be used from.any source. Thus, all required components can be connected together in a very simple manner with virtually no other external logic.
General Purpose Registers There are two matched sets of general purpose registers, each set containing six 8-bit registers that may be used individually as 8-bit registers or as 16bit register pairs by the programmer. One set is called BC, DE and HL while the complementary set is called BC’, DE’ and HL’. At any one time the programmer can select either set of registers to work with through a single exchange command for the entire set. In systems where fast interrupt response is required, one set of general purpose registers andan accumulator/flag register may be reserved for handling this very fast routine. Only a simple exchange command need be executed to go between the routines. This greatly reduces interrupt service time by eliminating the requirement for saving and retrieving register contents in the external stack during interrupt or subroutine processing. These general purpose registers are used for a wide range of applications by the programmer. They also simplify programming, especially in ROM based systems where little external read/write memory is available. Arithmetic & Logic Unit (ALU) The 8-bit arithmetic and logical instructions:of the CPU are executed in the ALU. Internally the ALU communicates with the registers and the external
REG ora AD WR SYSTEM CONTROL
cpu CONTROL
cPU BUS CONTROL
+5V GND
Z-80 PIN CONFIGURATION
6-4 data bus on the internal data bus. The type of functions performed ‘by the ALU include: Add Left or right shifts or rotates (arithmetic and logical)
Subtract Increment
Logical AND Decrement Logical OR Set bit Logical Exlusive OR Reset bit Compare Test bit Instruction Register and CPU Control As each instruction is fetched from memory, it is placed in the instruction register and decoded. The control sections performs this function and then generates and supplies all of the control signals necessary to read or write data from or to the registers, contral the ALU and provide all required external control signals.
Z-80 CPU Pin Description The Z-80 CPU is packaged in an industry standard 40 pin Dual In-Line Package. The I/O pins are shown in the below figure and the function of each is described.
p>
ADDRESS BUS PrRPPrPPrpPpPre
DATA BUS
Ao-Ais (Address Bus) Tri-state output, active high. Ao-A,5 constitute a 16bit address bus. The address bus provides the address for memory (up to 64K bytes) data ex- ‘ changes and for I/O device data exchanges. I/O addressing uses the 8 lower address bits to allow the user to directly select up to 256 input or 256 output ports. Ao is the least significant address bit. During ° refresh time, the lower 7 bits contain a valid refresh address.
Do-D; (Data Bus) . Tri-state input/output, active high. Dy-D; constitute an 8-bit bidirectional data bus. The data bus is used for data exchanges with memory and 1/O devices.
M, (Machine Cycle one) __ Output, active low. M, indicates that the current machine cycle is the OP code fetch cycle of an instruction execution. Note that during execution of 2-byte op-codes, M1 is generated as each op code byte is fetched. These two byte op-codes always begin with CBH, DDH, EDH or FDH. M1 also occurs with IORQ to indicate an interrupt acknowledge cycle. MREQ (Memory Request) Tri-state output, active low. The memory request signal indicates that the address bus holds a valid address for a memory read or memory write operation. 1ORQ (Input/Output Request) Tri-state output, active low. The ioRQ signal indicates that the lower half of the address bus holds a valid /O address for a !/O read or write operation. An JORG signal is also generated with an M1 signal when an interrupt is being acknowledged to indicate that an interrupt response vector can be placed on the data bus. Interrupt Acknowledge operations occur during M, time while I/O operations never occur during M, time. RD (Memory Read) Tri-state output, active low. RD indicates that the CPU wants to read data from memory or an I/O device. The addressed J/O device or memory should use this signal to gate data onto the CPU data bus. WR (Memory Write) Tri-state output, active low. WR indicates that the CPU data bus holds valid data to be stored in the addressed memory or I/O device.
6-5 RFSH (Refresh)
Output, active low. RFSH indicates that the lower 7
bits of the address bus contain a refresh address for dynamic memories and the current MREQ signal should be used to do a refresh read to all dynamic memories.
HALT (Halt state) Output, active low. HALT indicates that the CPU has executed a HALT software instruction and is awaiting either a non maskable or a maskable interrupt (with the mask enabled) before operation can resume. While halted, the CPU executes NOP's to maintain memory refresh activity. WAIT (Wait) Input, active’ low. WAIT indicates to the 2-80 CPU that the addressed memory or I/O devices are not ready for a data transfer. The CPU continues to enter wait states for as long ds this signal is active. This signal allows memory or I/O devices of any speed to be synchronized to the CPU. INT (Interrupt Request) Input, active low. The Interrupt Request signal is generated by I/O devices. A request will be honored at the end of the current instruction if the internal software controlled interrupt enable flip-flop (IFF) is enabled and if the BUSRQ signal is not active. When the CPU_accepts the interrupt, an acknowledge signal (IORQ during M, time) is sent out at the beginning of the next instruction cycle. The CPU can respond to an interrupt in three different modes that are described in detail in section 5.4 (CPU Control Instructions). NMI . (Non-Maskable Interrupt) Input, negative edge triggered. The non maskable interrupt request line has a higher priority than INT and is always recognized at the end of the current instruction, independent of the status of the interrupt enable flip-flop. NMI automatically forces the Z-80 CPU to restart to location 0066». The program counter is automatically saved in the external stack so that the user can return to the program that was interrupted. Note that continuous WATT cycles can prevent_the current instruction from ending, and that a BUSRQ will override a NMI. RESET Input, active low. RESET forces the program counter. to zero and initializes the CPU. The CPU initialization includes:
- Disable the interrupt enable flip-flop
- Set Register | = 00x
- Set Register R =00x
- Set Interrupt Mode 0 During reset time, the address bus and data bus go to a high impedance state and all control ouput signals go to the inactive state.
BUSRQ (Bus Request) Input, active low. The bus request signal is used to request the CPU address bus, data bus and tri-state output control signals to go to a high impedance state so that other devices can control these buses. When BUSRQ is activated, the CPU will set these buses to a high impedance state as soon as the current CPU machine cycle is terminated. BUSAK (Bus Acknowledge) . Output, active low. Bus acknowledge is used to indicate to the requesting device that the CPU address bus, data bus and tri-state control bus signals have been set to their high impedance state and the external device can now control these signals.
CLK (Clock) Single phase TTL level clock which requires only a 330 ohm pull-up resistor to +5 volts to meet all clock requirements. re a —eeeeanaeaRaunuqeeoeouyyyEElElElLleeEeEEEE—_—_—_—_———
a4
MANUFACTURER EPROM NO.
68764 MOTOROLA — 68766
INTEL
2564 xX g c =
MANUFACTURER EPROM NO.
68764 MOTOROLA — 68766
INTEL. 2764
EPROM NO. | JW#10
68764 MOTOROLA —_ 68766 cs a
INTEL g
MANUFACTURER EPROM NO. | JW#1
Zz Cc = m a fe) Cc a = nu D a
NUMEROUS MFR'S 2732 . JUMPER OPTIONS FOR MCR II SYSTEM P.C. BOARD JUMPER OPTIONS
VIDEO GENERATOR P.C. BOARD
SUPER C.P.U. P.C. BOARD
JUMPER OPTIONS FOR PROGRAM ROMS ONLY
= = a BA
SOUND I/O P. C. BOARD JWH7
CKGROUND ROM
JSWHIZ ao ° Zz <
rag WH
- = CUT JUMPER WIRES WHERE THIS SYMBOL “*” APPEARS. # = LEAVE JUMPER WIRES IN WHERE THIS SYMBOL “#” APPEARS.
The above table illustrates the fact that the Video Generator P.C. Board used in the MCR II System has 8 jumper wires, the SUPER C.P.U. P.C. Board used in the MCR II System has 19 jumper wires, and the Sound I/O P.C. Board used in the MCR II System has 2 jumper wires.
All of the above Boards can be used with a variety of different SETS of EPROM chips. However, these EPROMS are not all made by the same manufacturer
6-7 and do have some internal differences. So, in order to make them function properly in their respective P.C. Boards, certain jumper wires on these Boards have to be cut.
The above table tells you which jumpers to cut (depending on which EPROM set you're going to use) by showing a “*” under that jumper wire’s number. If there is NO “*” under a jumper wire's number, THAT PARTICULAR JUMPER WIRE IS NOT TO BE CUT.
myo
a)
VII. Coin Door Maintenance
SPECIAL NOTE: If you have any questions about the coin acceptors in your game(s), please feel free to contact their manufacturers. Each manufacturer's name is PROMINENTLY imprinted on every acceptor mechanism. Metal mechanisms only: COIN MECHANISMS, INC. 817 Industrial Drive Elmhurst, IL 60126 Phone (312) 279-9150
COIN DOOR MAINTENANCE
METAL COIN ACCEPTOR MECHANISMS Periodically, the metal coin acceptor mechanism(s) must be removed from the coin door and cleaned.
- Make sure the power to the game is off.
- Unlock and open the coin door.
TO REMOVE PUSH LATCHES DOWN
PLACE PEGS IN SLOTS TO REPLACE PULL MECHANISM OUT Metal and Plastic mechanisms: COINCO COIN ACCEPTORS, INC. 860 Eagle Drive Bensenville, IL 60106 Phone (312) 766-6781
- Remove the coin acceptor mechanism as shown in Figure 7-1. O Push down on the two spring loaded latches. O While holding the latches down, pull the top of the coin acceptor mechanism toward you. C Release the latches and lift out the coin acceptor mechanism.
PUSH MECHANISM IN
Figure 7-1 Removing and replacing coin acceptor
- Clean the magnet of all foreign particles. See Figure 7-2. . O This may be accomplished by swinging the gate open as shown in the above figure.
- Remove the cradles and undersize levers and clean the bushings. (A pipe cleaner makes a good ‘pushing cleaner.) D Also clean the pivot pin.
- Whenever needed, the coin acceptor should be cleaned with hot water and cleanser in the following manner: O Place the coin acceptor in boiling water for about ten minutes.
DO Next, use a brush and kitchen cleaner to remove all remaining foreign matter from the unit. O Rinse the coin acceptor in clean boiling water. O Dry the coin acceptor thoroughly by using filtered compressed air to blow it dry.
GATE OPEN AS SHOWN CLEAN MAGNET BY DRAGGING A SCREWDRIVER BLADE ACROSS SURFACE
Figure 7-2 Cleaning the metal coin acceptor
7-2
- To lubricate the coin acceptor: O Use ONLY powdered graphite and put it ONLY on the moving parts of the coin acceptor. These parts are called out in Figure 7-3. O Be extremely careful to keep the powdered graphite away from paths that are traveled by the coins.
- WARNING — DO NOT USE OIL TO LUBRICATE THE COIN ACCEPTOR.
- Check the coin chute for obstructions such as: paper, gum, etc. .
- Reinstall the coin acceptor to the coin door. See Figure 7-1. | O Place, the two pegs at the coin acceptor’s base into their retaining. slots. O Now push the top of the coin acceptor toward the coin door until it snaps in place and is held there by the two spring loaded latches.
- Close and lock the coin door.
APPLY POWDERED GRAPHITE HERE
CRADLE
Figure 7-3 Lubricating the metal coin acceptor
SQUEEZE PINS TOGETHER TO UNLOCK SWING BOTH GATES OPEN
HOLDING BOTH GATES TOGETHER, PUSH UP AND PULL OUT
Figure 7-4 Opening the plastic coin acceptor
PLASTIC COIN ACCEPTOR MECHANISMS The plastic coin acceptor mechanism(s) must:be removed periodically from the coin door and cleaned.
- Make sure the power to the game is off.
- Unlock and open the coin door.
- Remove the coin acceptor mechanism(s) as.. shown in Figure 7-1. © Push down on the two spring loaded latches. While holding the latches down, pull the top of . the acceptor mechanism toward you. O Release the latches and lift out the mechanism. 4, Squeeze the two pins indicated in Figure 7-4 together to open the mechanism and break it down into its three basic parts. Clean the mechanism in hot soapy water. It never rusts. O Rinse the mechanism in clean hot water and allow it to dry.
7-3 O Reassemble the mechanism (it never needs lubrication).
- Check the coin chute for obstructions such as: Paper, gum, etc.
- Reinstall the coin acceptor to the coin door. See Figure 7-5. . O Place the two pegs at the coin acceptor’s base into their retaining slots. O Now push the top of the coin acceptor toward the coin door until it snaps in place and is held there by the two spring loaded latches.
- ‘Close and lock the coin door.
ACCEPTOR CAN BE SET TO ACCEPT U.S. QUARTERS ONLY OR BOTH U.S. AND CANADIAN QUARTERS.
|}
SLIDE MAGNET TO EXTREME RIGHT (AS SHOWN) TO ACCEPT BOTH U.S. AND CANADIAN QUARTERS.
TO ACCEPT U.S. QUARTERS ONLY, SLIDE MAGNET TO EXTREME LEFT.
Figure 7-5 Changing the plastic coin acceptor to accept American or Canadian quarters. _}
—)
PLEASE NOTE:
THE INFORMATION CONTAINED IN THIS SECTION IS TOLD IN AN EASY TO UNDERSTAND MANNER AND IS INTENDED TO AID THOSE WITHOUT AN " ELECTRONICS DEGREE IN TROUBLESHOOTING AND REPAIRING THEIR GAMES T.V. MONITOR.
IF YOU READ THROUGH THIS SECTION AND STILL HAVE QUESTIONS, PLEASE CONTACT YOUR DISTRIBUTOR OR MIDWAY MANUFACTURING COMPANY AT THE TOLL FREE NUMBER PROVIDED WITH YOUR GAMES PAPERS.
OUR STAFF AND OUR DISTRIBUTORS STAND READY TO HELP YOU!
THANK YOU .
Vill T.V. Monitor Manual
Color T.V.
Introduction: (How to
use this section of your manual.)
This section has been designed to simply familiarize you with one of the more mystical components in your game — the T.V. monitor. If you are an electronics technician who is quite knowledgeable on the subject, you may decide to just go to the schematics and start troubleshooting the defective monitor. But if you are like most people, a monitor is a T.V. set, and that means a complex doo-dad that means big buck repairs. This isn’t necessarily so. This section of the manual will acquaint you with the monitor and could just help you repair it if you feel adventurous enough to give it a try. If you have any knowledge of electronics, especially. the use of a voltmeter, the repairs you can make are astonishing. Just keep in mind that ELECTRICITY CAN BE VERY DANGEROUS, SO BE CAREFUL!!
'f you want to understand how a monitor works, just read the “THEORY OF OPERATION” subsection. If you wish, you can follow along with the schematics. The information is presented in a very basic manner but more complete treatment of the subject can be found in the technical sections of bookstores.
\f.you want to attempt to repair your monitor, it would be a good idea to read this whole section beginning to end before starting. Pay attention to all warnings Monitor |
and take them seriously. The more equipment you have the better, but a low cost Volt-Ohm-Milliameter can often, do the trick. Here are the steps to take:
- Find the symptom that matches the problems your monitor has in the “SYSTEM — DIAG- NOSIS” subsection. The diagnosis tells the circuit or area the problem may be in and possibly even the actual component causing it.
- Once you have the circuit that is causing the trouble, read the “TROUBLESHOOTING” subsection to learn the procedure for finding the bad part.
- Next, go to the schematic section and find the schematic that matches your monitor. It may be helpful to read the “DIFFERENCES BETWEEN MONITORS” subsection if you are unsure of which monitor you have. Use the schematic to see what parts are in the offending circuit.
That really is all there is to it. Just remember that there are some bizarre or rare symptoms not covered, or that a monitor may have two or more different problems that only a genius, the experienced, or an experienced genius can figure out. But be patient, follow safety precautions, and remember that there is also literature available from the monitor companies through your distributor or frorn Midway Manufacturing Company on request. (There is a toll free number on the back side of the front cover of this manual.)
Symptom Diagnosis
. Insufficient width or heighth: A. Horizontal line (due to VERTICAL CIR- ° CUIT DEFECT). O Bad yoke. O Bad vertical output section. O Open fusible resistor in vertical section. O Bad height control. O Bad flyback. B. Vertical line (due to HORIZONTAL CIR- CUIT DEFECT). O Bad yoke. O Open width coil. O Open part.in horizontal output section. . Picture spread out too far or crushed in certain areas: . A. Horizontal or vertical output transistor. B. Bad component in output circuitry. Line too close with black spacing: i A. Problem in vertical section causing poor linearity. . Poor focus and convergence: A. Bad high voltage transformer (“flyback”) or control. B. Focus voltage wire not connected to neckboard terminal. . Colors missing; check: A. Interface color transistors. B. Color output transistors. C. Cracked printed circuit board. D. Color circuits. E. Video input jack. Picture not bright enough: A. Weak emission from picture tube. (Turn horizontal sync off frequency and put brightness all the way up for about 15 minutes. Occasionally this cures the problem.) .. Silvery effect in white areas; check: A. Beam current transistors. B. Weak picture tube emission. . Too much brightness with retrace lines; check: A. Beam limiter transistors. B. Brightness and/or color blanking control set too high. . Increasing brightness causes an increase in size and poor focus.
A. Weak high voltage rectifier or regulation
(high voltage unit).
8-2 10.
11.
12,
13.
14,
15.
16.
17.
18.
19. Small picture and/or poor focus: A. Low B+ voltage (power supply trouble).
Vertical rolling: A. Vertical oscillator transistor, IC, or circuit. B. No sync from logic board.
Horizontal line across center: A. Vertical output circuit is dead (see symptom No. 1. A.). B. Vertical oscillator is not putting out the right wave form. Picture bends: A. Horizontal sync needs adjusting. B. ‘Magnetic or electromagnetic interference.
Flashing picture, visable retrace lines: A. Broken neck board. B. Internal short circuit in the picture tube (arcing).
Unsymmetrical picture or sides of picture:
A. Defective yoke.
No brightness, power supply operating — No high voltage for the picture tube; check: A. Horizontal oscillator. B. Horizontal amplifier and output. Cc. Flyback transformer (high voltage unit).
No brightness, high voltage present; check: A. Heater voltage to the tube at the neck board. B. Screen-grid voltage for the tube. C. Focus voltage: D. Grid to cathode picture tube bias.
No high voltage; check: ‘ A. For AC input to the “flyback”. B. Horizontal deflection stages. C. Flyback transformer. D. Yoke. ~ E. Power supply.
No horizontal and vertical hold; check: A. Sync transistors and circuit. B. Wires and jack from logic board to the monitor. Wavey picture — (power supply defect); check: A. Transistors, diodes, electrolytic capacitors “inthe power supply.
- Moving bars in picture: A. Ground connector off between monitor and logic boards. B. Defect in the power supply (see wavy picture symptom).
- Washed out picture (see picture not bright enough): A. Check video signal at the cathode pins with an oscilloscope. If there is about 80 volts peak to peak, the picture tube has weak emission."
- Monitor won’t turn on: A. Problem in the power supply: Check fuse, transistors, open fusible resistor. B. Shorted horizontal output transistor. C. Defective high voltage disabling circuit. D. Crack(s) somewhere on main chassis board.
- Can't adjust purity or convergence:
A. Use a degausser to demagnetize the picture tube carefully following your degaus- .Ser's instructions. B. Picture tube defective. C. Metal foreign material is in picture tube shield. D. Nearby equipment is electromagnetically interfering. E. The poles of the earth are pulling off the purity. F. Poor focus or width of picture.
Guide To Schematic Symbols
THERMISTOR
(POLARITY DOESN'T MATTER)
SY WL INDUCTOR, COIL, CHOKE (POLARITY DOESN'T MATTER)
(-) CATHODE
(+) ANODE
ZENER DIODE
8-3 IRON CORE TRANSFORMER (SUCH AS A FLYBACK)
mC oe
FUSE (POLARITY DOESN'T MATTER)
CATHODE (-)
ANODE (+)
DIODE
COLLECTOR To a COLLECTOR BASE ————> ; BASE———> _ EMITTER ; EMITTER mS
NPN TRANSISTOR ; PNP TRANSISTOR
MWv—
VARIABLE RESISTOR, POT, CONTROL . ‘RESISTOR (POLARITY DOESN'T: MATTER) (POLARITY DOESN’T MATTER)
o +
LINES ARE CONNECTED ELECTROLYTIC CAPACITOR
LINES ARE NOT CONNECTED . CAPACITOR (POLARITY DOESN'T MATTER)
GROUND
8-4
x e
Troubleshooting
Troubleshooting monitors requires experience, patience, and luck. The first step is to match the symptom the monitor displays to the diagnosis next to it in the “SYMPTOM-DIAGNOSIS” subsection. This will pinpoint the circuit the problem is probably in, and often the parts to check. Next, the circuit should be visually inspected to see if there are any parts broken, burned, or if something is there that shouldn't be, like a loose screw, etc. Some parts go bad before others and should be checked first. In fact, following is the general order in which parts usually go bad:
- Semiconductors (like transistors, diodes, and integrated circuits).
- Fusible resistors.
- Electrolytic capacitors.
- Resistors.
- Capacitors and coils. Always remember that a monitor can bite like a snake. Even when it is turned off, capacitors hold voltage and will discharge it to you should you be touching chassis ground. The picture tube or CRT, itself, is a giant capacitor, so avoid the flyback anode plug hole. With the monitor on, the power supply circuit and/or.the flyback, which puts out at least 18,000 volts, CAN BE KILLERSI!! Avoid handling power transistors (usually output transistors), yoke healthy charge for at least a week if not longer. Even after you've discharged it once, it may still carry a residual charge. It's better to be too careful than dead, which is why electronic equipment always carries stickers referring servicing to qualified personnel. Handle the side with the viewing screen against your chest when changing it. ALWAYS wear safety goggles when handling the picture tube.
To maintain the safety and performance of the monitor, always use exact replacement parts. For instance, the wrong components in the power supply can cause a fire, or the wrong color transistor may give a funny color to the picture. Service your manitor on a, nonconductive firm table like wood, NOT METAL, and take off all of your jewelry just in . case. With all this in mind, you are ready to. begin
terminals, and other high power components when + the monitor is on.
Observe the picture carefully. Try to vary the appropriate control that would most likely affect your particular symptom. For example, if there is poor brightness or no picture, try turning up the brightness or contrast control. If the controls have no effect at all, chances are there is trouble with the contro! itself, the circuit it controls, or a nearby circuit that may be upsetting voltages. Go to the list of symptoms and determine with the schematic where the bad circuit is.
Keep in mind that capacitors hold a charge as can the picture tube (for at least a week and usually longer), and could shock you.
First, check for obvious visual defects such as broken or frayed wires, solder where it is not supposed to be, missing components, burned components, or cracked printed circuit boards. If everything looks good up to this point, make sure that diodes, electrolytic capacitors, and transistors have their leads connected in the right polarity as shown on the schematic and the circuit board. Turn on the power and measure the voltages at the leads of the active devices 'such as tubes; transistors, or integrated circuits. Any voltage that does not come within at least 10% to 15% of the voltage’ specified on the schematic indicates either a problem with that device or a component connected with it in the circuit. The next step is to use the ohmmeter to narrow down the field of possible offenders.
To test a transistor, one lead of the ohmmeter is placed on the base; and the other lead placed just on the emitter, then on the collector. A normal transistor will read either high resistance (infinite), or little resistance (400 to -900 ohms), depending on the polarity of this type transistor. Then the leads should be switched, one remaining on the base, and the other switched from the emitter to the collector. Now the opposite condition should result: the resistance should be infinite if it was lower when the other lead was on the base. Consistantly infinite readings indicate an open, anda short is demonstrated by 0-30 ohms on most of these test readings. Finally, place one lead on the collector, then the other on the emitter. No’ matter which lead is used, there should be infinite resistance. Any lower reading, such as 50 ohms (which is typical on a bad transistor), indicates a short. : This all sounds pretty confusing, but a little experience on a good transistor will make you an expert in no time. Usually, the lowest ohmmeter setting is used for testing transistors. Once in a: great while a transistor may check out good on this test, but may actually be “leaky” or break down only on higher voltages. If in doubt, change it. It is also wise to check the transistor out of the circuit just in case some component in the circuit is affecting the ohmmeter reading. A diode is tested like a transistor except it only has two leads. Again, there should be high resistance one way and little resistance the other. If it tests bad, take one lead out of the circuit in case some componentis messing up the ohmmeter reading.
Without special equipment, integrated circuits are checked by verifying the proper DC voltage on the pins and the correct AC wave form using an oscilliscope. BE CAREFUL: Shorting their pins can easily destroy them. Resistors are checked with an ohmeter and should usually be within ten percent of the value stated on .them and on the schematic. You may have -to desolder one lead from the printed circuit board. If you wreck the foil on the board, carefully solder a small wire over the break to reconnect the conductive foil. Capacitors are tricky. Their resistance goes up when checked with an ohmmeter which shows a charging action. As they suck up current from the meter, the voltage goes up and so does the resistance. If you are Sure a particular circuit is giving you a problem and everything else checks out O.K., Electrolytic capacitors are prime suspects. Substitute a new one and keep your fingers crossed.
Theory of Operation
To understand what goes on inside the monitor, large general groups of circuits will be examined instead of laboriously analyzing the branches and small circuits that make up these groups. This will help avoid confusion and aid in a basic, concrete, knowledge of what makes up a monitor.
THE POWER SUPPLY — The AC going to the monitor from the game transformer is just like the voltage and current from your wall outlet. It jumps up and down going positive and negative sixty times a second. But a monitor needs nice, smooth DC; direct current, not alternating. So diodes chop up the AC and a big electrolytic capacitor filters it out to make it even smoother. Since the monitor is a big piece of electronic equipment, with many circuits demanding a lot of power from the power supply, there are also zener diodes and transistors to help maintain a nice, constant, smooth voltage so that the monitor circuits don't jump around. And this is what happens when you see a wavy picture. There is AC creeping
8-6 through the power supply, so it must be malfunctioning. If the voltage from the power supply is too low, the other circuits will be starved for power and you may see a small, wavy picture, or none atall. Some circuits receive voltages that are higher than what the power supply should put out. But they come from the flyback transformer which will be discussed later. ‘
THE INTERFACE SECTION OF THE CHASSIS — The interface section of the chassis is fairly easy to identify. It is right by the place where the video jack(s) from the logic board(s) plug into. There are sets of transistors that receive the separate red, green, blue, and sync information from the cables that come from the logic boards. The circuits jack up the voltage and match impedances, or in other words, prepare the logic board outputs for the circuits that will really amplify them for the output devices such as the yoke in the case of the sync, or the picture tube that shows the colors.
ty
iT
aT _An interesting aside is that our sync is composite negative sync. That means two things:
- The sync is a negative going wave form.
- There are two pulses going at different speeds over the same wire: a. Vertical wave forms at 60 times per second (or Hertz) and b. Horizontal wave forms at about 15,750 times per second (Hz). The sync is amplified by a sync amplifier transistor and sent on its way to the oscillators. The sync or timing information will be explained along with the oscillator shortly. The color information is sent via wires to the neck board where the main amplification occurs. This will also be discussed later.
VERTICAL AND HORIZONTAL
DEFLECTION— After the sync signal is amplified by the sync amp, it goes to two different sections, the vertical and horizontal circuits. Basically, the sync signals are for timing so the picture doesn’t mess up since it is assembled like an orderly jigsaw puzzle, but so fast that you can't see the electron beams for each color painting the picture on the screen. This will all become clear soor. For now, we will follow the-60 cycle component of the sync as it goes on its journey to the deflection yoke. The 60 cycle pulse goes to the vertical oscillator to make sure this circuit goes back and forth (or oscillates) at 60 times a second. Without this pulse keeping the circuit at the correct speed, it may get lazy and oscillate at 58 cycles or lower, or get ambitious and oscillate at 62 cycles or higher. At the wrong speed, the picture will start to roll up or down. A Wells Gardner 13” (K4806) or 19” (K4906, K4956) color monitor uses an integrated circuit for its sync section. An Electrohome 13” or 19” color monitor uses an integrated circuit |C501 for its sync section. Wells Gardner uses HA11423 and Electrohome uses HA11244. These ARE NOT interchangeable! The idea is all the same. The output to the vertical amplifying transistors for all monitors must form a sawtooth wave form, sort of like a bunch of pyramids, racing through the yoke’s vertical coils at 60 times a second. Along the way to the output transistors, the 60 cycle pulse is shaped and amplified to do the job: the yoke magnetically pushes the electron beam to fill the screen out sideways looking at the screen with the greatest length going up and down. Or viewing the screen sitting like a home television set, the amplified vertical output fills the screen up and down. Watching a monitor like this, seeing only a horizontal line means a problem with the vertical coils of the yoke or anything from the vertical output section on back to the oscillator.
8-7 The horizontal section is very similar with a few exceptions. The horizontal wave shape is more like a square and has a frequency of 15,750 cycles a second. Both Wells Gardner and Electrohome use the other side of their respective integrated circuits for the horizontal circuitry. If the oscillator isn't going at the correct speed, the picture may move sideways, start to slant, or tear up with slanted thin figures. With both the vertical-and horizontal of all monitors, there are variable resistors that change the speed of the oscillators up and down. This way you have controls that can make the correct frequencies to keep the electronic jigsaw puzzle nicely locked in place. If you're driving in a car and next to you someone else is driving their car at exactly the same speed, it will appear that they are not moving. And this is why the sync frequency and the oscillator’s frequency must match, so the picture doesn’t appear to move. The correct wave form is shaped and amplified in the circuitry just.like in the vertical section. But the horizontal output transistor is a large power transistor and not only serves to give current to the horizontal yoke windings, it also feeds the flyback transformer.
THE FLYBACK TRANSFORMER (OR HIGH VOLTAGE UNIT) — The picture tube needs high voltage to light up, and the power supply can’t meet this demand. The flyback transformer receives current alternating at about 15,750 times per second from the horizontal output transistor. The “flyback” jacks up its input voltage and puts out a higher voltage alternating at the same speed. But, in your “flyback” there are diodes that chop up the alternating voltage to make it asmooth DC output just like in the power supply. This is what goes through that thick red wire to your picture tube. THIS AREA HAS ABOUT 18,000 VOLTS, ON IT AND IT CAN KILL YOU! The “flyback” may be dangerous, but it is also generous. It has extra output windings which give voltage to the heater pins of the picture tube, voltage for the vertical deflection circuits, and picture tube screen-grid voltage. So in a way, the high voltage “flyback” is like a second power supply.
COLOR CIRCUITS — The color circuits are pretty straight forward. The signals go into the interface section where some amplification and impedance matching occurs. These circuits are pretty sparse and simple. Each color just has two transistors and a diode with some resistors and capacitors. From here, the AC color signal is sent by wires to the neck board. The color output circuits are on the neck board. The color signals going to the transistors are controlled by two variable resistors called drive controls. There are only two, one for the red and one for the green.
screen. Moving the Control may distort the top part of your picture (or the side, depending on the game and how the monitor is mounted) so go.ahead and move it if you are having this type of problem. To accommodate this new feature, there are a few circuit changes. ONE MAJOR DIFFERENCE BETWEEN THESE TWO VERSIONS OF THE K4906 IS THE YOKE. They look the same but notice the part numbers: K4906 WITHOUT the Damper Control: 2021111201 K4906 WITH the Damper Control: 2021111258 Since the companies like to change part numbers at the drop of a hat, the best thing to do is to request whatever part number is written on your yoke. If you should get the wrong yoke, the results will be: Picture distortion. Excessive brightness. Too much or too little vertical picture size. K4956 (3rd TYPE) — This monitor is identical to the K4906 WITHOUT the Damper Control EXCEPT the picture tube .is vertically mounted and there is an additional: small P.C. Board mounted on the monitor where the yoke plugs in. This monitor is used on some Cocktail Table games where the picture has to flip for the second player. Generally speaking, some games flip the picture image via the logic board programming but this monitor is used in games that flip the picture image via generation of a small signal voltage which is sent to the extra P.C. Board on this monitor. This signal voltage causes relays on this extra P.C. Board to flip the picture by reversing the horizontal and vertical signals to the yoke pins. What kind of problems can this extra P.C. Board cause? If the relays become defective, the picture won't flip. If the P.C. Board gets cracked you may have a horizontal line on the screen, a vertical line on the screen, or maybe just a dot in the center of the screen. Of course, the logic board could be defective and not sending the signal to flip the picture. In any case, some people feel that using relays is cheaper, simpler, and more reliable, so this is an advantage.
CONTROLS YOU MAY NOT TOUCH Basically, on the Electrohome monitor, you can move any control you want EXCEPT for the B1 control. This sets the power supply voltage (ideally at 120 VDC) and is located right behind VERTICAL HOLD. The'13” Electrohome DOES NOT have this control. It may also be wise not to move the VERTICAL LIN- EARITY since this distorts the picture and is hard to reset perfectly. If you do move it, turn on the Cross Hatch Test Pattern of your game and try to get the squares to the point where they are equal in size by readjusting this Linearity Control. On the Wells Gardner monitor, brightness is adjusted
by the “BLACK LEVEL” Control which is right next to
the Horizontal Frequency Control. Under the Focus Control is the “SCREEN” Control which youDO NOT touch. Yes, this control does adjust the brightness, but it is used to set the CRT bias and is adjusted at the factory. When Wells Gardner sets it, they mark the position with a black mark on the knob. If you move it, be sure to realign the mark and THEN set the BLACK LEVEL Control to the brightness you desire. So, other than the SCREEN control, you may adjust any of the controls.
Parts Interchangeability
Some parts can be interchanged on all of the monitors. Here are the rules:
- You CAN swap any resistor between monitors that has the same resistance, wattage rating, and tolerance. "
- You CAN swap any capacitor between monitors that has’ the same capacitance and voltage rating.
- You CAN swap many of the parts between the 49" and the 13” versions of each manufacturer's . Monitor. BUT, be certain to compare the manufacturers’ part numbers to be positive the parts you want to interchange are identical. BE SURE you have read the section DIFFERENCES BE- TWEEN MONITORS which was covered earlier.
- You CANNOT swap any picture tubes between
- monitors!! In the past you could, but Wells Gardner is now using a new monitor. When
8-9
ordering a replacement picture tube, ALWAYS
SPECIFY THE PICTURE TUBE NUMBER!
- You CANNOT change any part that is a safety part, one that is shaded in gray on the schematic; it MUST be IDENTICAL to the original. To do otherwise IS DANGEROUS. For instance, the 13 inch Electrohome (G07-902) monitor “flyback” looks identical to the 19 inch Electrohome (G07- 904) monitor “flyback”. In fact, there is even a 19 inch Electrohome (G07-905) monitor (which is an obsolete model) with a similar looking “fly- -back”. NONE OF THESE ARE INTER- CHANGEABLE!!
- You CAN change any of the parts between the G07-904 and G07-907. They're essentially the .
same monitor except that the G07-907 has a
vertically mounted picture tube. If there is any doubt about what parts can be swapped between each manufacturer's 19 inch and 13 inch models, compare the manufacturer's part number between each one. If they match up, they are the same part.
ITOR SCHEMATIC DIAGRAM bee
1, 19K4906, 19K 4951, 19K4956 : TAN . . OSCILLOSCOPE WAVEFORM PATTERN -GAUTION: FOR CONTI "~The waveforms shown are as observed on the wide band reaurions: Ayan cNuED, Bai pad aa oscilloscope with the monitor turned to a reasonably
| PONENTS ONLY WITH | MANUFAC. | : | 7 | strong signal and a normal picture. The voltages shown |
| TURER’S RECOMMENDED PARTS. | * | on each waveform are the approximate peak ampll- | ||
| AVERTISSEMENT: | POUR MAINTENIR | : | tudes. | : |
| LE DEGRE DE SECURITE DE L’APPAREIL | - | . | 'f the waveforms are observed on the oscilloscope with |
NE REMPLAGER LES COMPOSANTS . .
| DONT LE | FONCTIONNEMENT tSy | ; | @ poor high frequency response, the corner of the |
| CRITIQUE POUR LA SECURITE QUE PAR | ~ | Bulses will tend to be more rounded than those shown |
DES PIECES RECOMMANDEES PAR LE and the amplitude of any high frequency pulse will FABRICANT. tend to be less.
oe : om 7 Ekten 0381 HOR OR VE ascesi awe siibuen asctenaen Fa one 7H Ino a0
a7) caer” " sP/B00y *
se ka9010, Ka9060, Ka951D 5833 Kao5e8 ate
19” COLOR MONIT MODELS 19K4901,
SERVICE TECHNICIAN WARNING X-RAY RADIATION PRECAUTION:
THIS PRODUCT CONTAINS. CRITICAL
ELECTRICAL AND MECMAMICAL PARTS ESSENTIAL FOR X-RAY RADIATION l? . PROTECTION. FOR REPLACEMENT: PURPOSES, USE ONLY TYPE PARTS SHOWN. IN THE PARTS LIST. 5
O.S/DIV 20u SEC/DIV 1G, 901, PINS F an 1.C. 301, PIN 15
REPLACEMENT PARTS LIST This monitor contains circuits and components Included specifically for safety purposes, For continued protection no changes. should be made to the original design, and components shown in shaded areas of schematic, or 4 *& ‘on parts list should be replaced with exact factory replacement parts. The use of substitute parts may create a shock, fire, radiation or other hazard. Service should be performed by qualified personnel only.
MAIN BOARD
| Ret. Ne. | Part Ne. | Description | Ret. No. | Part No. | Description |
RESISTORS RESISTORS (CONT.)
| R201 | 209x0500-645, | 1K Ohm, 5%, 1/4W Carbon | R369 | 203x8602-329 | 680K Ohm, 5%, 1/2W Comp. | ||
| R202 | 203X6500-523 | 30 Ohm, 5%, 1/4W Carbon | R370 | 203X6501-002, | 33K Ohm, 5%, 1/4W Carbon | ||
| R203 | 203X6500-405 | 100 Ohm, 5%, 1/4W Carbon | R371 | 203X9014-584 | * 1K Ohm, 5%, 1W Metal Oxide | ||
| R204 | 203X6700-327 | 100 Ohm, 5%, 1/2W Carbon | R972 | 203X9101-119 | 12K Ohm, 5%, 1W: Metal Oxide | ||
| R205 | 203X6700-421 | 270 Ohm, 5%, 1/2W Carbon | +) | R75 | 203X6700-763 | 8.8K Ohm, 5%, 1/2W Carbon | |
| R206 | 203X6500-540 | 390 Ohm, 5%, 1/4W Carbon | R376 | 203x0104-404 | 270 Ohm, 5%, 2W Metal Oxide | ||
| R207 | 340X2201034 | %, 1/4W Carbon | Ra7? | 203X6500-447 | 150 Ohm, 5%, 1/4W Carbon | ||
| R208 | 20300500-540 | '%, 114 | Carbon | R378 | 203x6500-886 | 10K Ohm, 5%, 1/4W Carbon | i |
| R200 | 340X2201-934 | %, 114W Carbon | R370 | 203X@500-886 | 10K Ohm, 5%, 1/4W Carbon | i | |
| R210 | 203X8500-540 | %, 1/4W Carbon | R380 | : | 8.2K Ohm, 5%, 1/4W Carbon | : | |
| R211 | ‘940X2201-034 | ~ | 1» 5%, 1/4 Carbon | R381 | 203X6500-724 | 2.2K Ohm, 5%, 1W Metal Oxide | |
| R214 | 203x8600-645, | “1K Ohm, 8%, 1/4W Carbon | R383 | 203X9014-387 | 150 Om, 5%, 1W Metal Oxide | ||
| R215 | -203K8801-128 | 100K Ohm, 5%, 1/4W Carbon | R502 | 10K Ohm, 5%, 1/4W Carbon | |||
| R216 | '203X8500-648 | 1K Ohm, 5%, 14W | R503, | + 204X1700-535, | 150 Ohm, 5%, 15W Metal Oxide | ||
| R217 | 203X6500-408 | ~ 100 Ohm, 5%, 1/4W Carbon | S04 | 203x9014-287 | 47 Ohm, 5%, 1W Metal Oxide | i | |
| R218 | . 208x8800-645, | 1K Ohm, 5%, 1/4W Carbon | R505 | 203x6501-208 | 2.2K Ohm, 5%, 1/4W Carbon | i | |
| R219 | 209K0601-128 | R506 | 203X9104-105 | 15 Ohm, 5%, 2W. Metal Oxide | : | ||
| R220 | 203x8500-645, | R507 | 203X5602-185 | 330K Ohm, 5%, 12W Comp. | ~ | | | |
| Rat | 203X8500-405, | Awns01 | 204x1625-088 | 3.3 Ohm, 5%, 10W WW | t | ||
| R222 | 203x6500-762 | R701 | 203X9105-141 | 2.2 Ohm, 5%, 2W Metal Oxide | ' | ||
| R224 | 203X6500-169 | R702 | 203X6206-441 | 2.2 Ohm, 5%, 1/2W Carbon | |||
| R226 | 203x8500-169 | R201 | 2042070072 | 2K Ohm-B Semi-Fixed | 7 | ||
| R228 | 203X6500-169 | R301 | 204X2070-084 | 5K Ohm-B Semi-Fixed | |||
| R227 | 203X0501-044 | R903 | 204X2070-065 | 500 Ohm-B Semi-Fixed | BS | ||
| Re28 | R361 | 204x2070072 | 2K Ohm-B Semi-Fixed | ; | |||
| R220 | 203X6700-421 | VR352 | 204x2070072 | 2K Ohm-B Semi-Fixed |
R230 203X6500-863 R231 203X6500-863, pase 203X6500-863 :
| R234 | 340X2820-034 | 82 Ohm, 5%, 1/4W Carbon | CAPACITORS | |||
| R236 | 340X2620-034 | 82 Ohm, 5%, 1/4W Carbon | C201 | 203x001 4-088 | 1000 uF, 16V, Electrolytic | |
| R236 | 340X2820-034 | 82 Otim, 6%, 1/4W Carbon | C202 | 202X7200-084 | 330 pF, 500V, Ceramic | |
| R301 | 203X6500-508 | 270 Ohm,8%, 1/4W Carbon | 6203, | 202X7200-043 | 220 pF, 500V, Ceramic | |
| R302 | 203x8500-863, | 8.2K Ohm, 5%, 1/4W Carbon | C204 | 202X7200-043 | 220 pF, S00V, Ceramic | |
| R303 | 203x6500-863 | 8.2K On, 5%, 1/4W Carbon | C205 | 203x0014.076 | 470 uF, 16V, Electrolytic | |
| - R304 | 203X6500-724 | 2.2K Ohm, 8%, 1/4W Carbon | C206 | 203X1810-149 | 0.1 uF, 125V Mylar | |
| R305 | 203X6500-842 | 6.8K Olun, 8%, 1/4W Carbon | 207 | 349X2232-109 | 022 uF, 100V Mylar | |
| R308 | 203X6003-201 | 7.5K Ohm, 2%, 1/4W Carbon | C301 | 203X0014-065 | 330 uF, 50V Electrolytic | |
| R307 | 203X6500-825 | 8.8K Ohm, 8%, 1/4W Carbon | 302 | 203X1600-563 | 0.033 uF, SOV Mylar | |
| R308 | 203x0500-065, | 22K Ohm, 8%, 1/4W Carbon | 303 | 3.3 uF, SOV Electrolytic | ||
| R310 | 203X6500-088 | 20K. Oben, 5%, 1/4W Carbon | C304 | 203X1600-366 | 0.088 pF, SOV Mylar | |
| R311 | 203X6500-762 | 3.3K Ofim, 5%, 1/4W Carbon | 308 | 203x0412-012 | 2.2 uF, 16V Tantal | |
| R312 | 203x9014-741 | 4.7% Ohm, 8%, 1/4W Carbon | “6307 | '203x1600-434 | 0.033 uF, S0V'Mytar | = * |
| 313 | 204X1480-837 | 1K Ohmi, 5%, BW Carbon’ | C308 | 208X0025-174 | 3.3 UF, SOV Electrolytic | |
| R314 | 203x8800-481 | 220 Ohm, 8%, 1/4W Carbon | 6309 | 203x1207-100 | 0.068 uF, 100V PP | |
| 315 | 203X6500-160 | 10 Ohm, 8%, 1/4W Carbon | C310 | 209x0629-061 | 10 uF, 100V Electrolytic | |
| R318 | 203x0600-762 | 3.3K Ohm, 8%, 1/4W Carbon | C311 | 203X0081-025 | 10 uF, 160V Electrolytic | |
| R317 | 203%8700-107 | 42 Ohm, 8%,.1/2W Carbon | C312 | X7060-248 | 1000 pF, 500V Ceramic | |
| A318 | 380 Onn, 5%, 1/4W Carbon | 0313 | 47 uF, 160V Electrolytic | |||
| R319 | 1K Ohm, §%, 1/4W Carbon | 314 | 208X1201-265 | 0.033 uF, 200V PP | ||
| R320 | 203X6601-002 | 33K Ot, 8%, 14W Carbon | C315 | 1 uF, 50V Electrolytic | ||
| R321 | 203X6801-224 | 270K Ohm, 6%, 1/2W Carbon | 351 | : | 1 uF, SQV Electrolytic | |
| A322 | 203x8600-886 | 10K Ohm, 5%, 1/4W Carbon | C362 | 203X0619-045, | 47 uF, 25V Electrolytic | |
| R51 | 203X6500-886 | 10K Ohm, 8%, 1/4W Carbon | 6353 | 203X1190-015 | 0.0082 pF, SOV Mylar-PP | |
| R352 | 203X6500-785 | 3.9K Ohm, 5%, 1/4W Carbon | 0354 | 203X0619-045, | 47 UF, 25V Electrolytic | |
| R353 | '209X8501.086 | 68K Ohm, 5%, 1/4W Carbon | C355 | 203X 1600-386 | 0.0088 pF, 50V Mylar | |
| F354 | 203X6500-i | 3.3K Ohm, 5%, 1/4W Carbon | C356 | 202X7050-483. | 0.01 uF, 500V Ceramic | |
| R355 | 209X9208-143 | 6.8K Ohm, 5%, 3W Metal Oxide | 359 | 100 pF, 500V Ceramic | ||
| R388 | 203x8601-878 | 58K Ohm, 8%, 1/2W Carbon | C380 | 202X7080-366 | 0.0033 pF, 8004 Ceramic | |
| R360 | 203X6500-861 | 470 Ohm, 5%, 1/4W Carbon | c3e1 | 202X7050-483 | 0.01 uF, S00V Ceramic | |
| R961 | 10K Ohm, 5%, 1/4W Carbon | 0362 | 202x7203.032 | 0.01 uF, SOV Ceramic | * | |
| R962 | 203x9014-648 | 1.8K Ohm, 5%, 1W Metal Oxide | AwC383 | 203X1270-011 | 8700 pF, 1.5 KV PP | |
| We R363 | 204X1827-781 | 3.8K Ohm, 8%, 7W Metal Oxide | W385 | 209X1201-265 | (0.33 uF, 200V PP | |
| A364 | 203X6800-246 | 22 Ohm, 8%, 14W Carbon | * 6388 | 203X0019-028 | 22 uF, 25V Electrolytic | . |
| F965, | 203X6501.002 | 33K Ohm, 5%, 1/4W Carbon | C367 | 202X8085-162 | 6 pF, 500V Ceramic | |
| R367 | 203X6500-886 | 10K Ohm, 5%, 1/4W Carbon | C368 | 202X7203-032 | 0.01 uF, SOV Ceramic | |
| R368 | 209X8602-185 | 330K Ohm, 5%, 1/2W Comp. | 372 | 203X1207-125 | 0.1 uF, 100V PP |
, aE MAIN BOARD (CONT)
| Rat Ne. | Pert We. | Deseription | Ret. No. | Part No. | Deeoription |
CAPACITORS (CONT.) SEMICONDUCTORS (CONT.)
| 380 | 202X7200-087 | 470 uF, 800V Ceramic | ; | 208 | 200K3181-523 | Transistor (NPN) 28C1815GR | : |
| 4.0501 | 209x1810-149 | 0.1 uF, 125V Mylar | 207 | 200X3181-623 | Transistor (NPN) 28C1815GR | é | |
| 4 c802 | 202X7080-262 | 1800 pF, 800V Cerantic | 208 | 200x$181523, | “Transistor (NPN) 28C1815GR | ||
| _ 40503 | 202x7810-214 | 2200 pF, 126V. Ceramic | 209 | 200X3181-523 | Traneistor (NPN) 28C1851GR- | + | |
| AcE04 | 202X7610-214 | 2200 pF, 125V Ceramic | 210 | 200x3181-523, | Transistor (NPN) 28C1851@A. | ||
| C508 | 203x0220.075 | 580 uF, 200V Electrolytic | 301 | 200X3181-523 - | Transistor (NPN) 250105: | : | |
| C506 | 203X0040-034 | 22 uF, 160V Electrolytic | a0 | 200X3207-308 | Transistor (NPN) | a | |
| cso? | 203X0041-087 | 47 uF, 180V Electrolytic | 303 | 200X3207-308 | Transistor (NPN) 2SC2073LBGL2 | ||
| 701 | 203X0019-092 | 1000.uF, 25V Electrolytic | 0351 | 200x3248-217 | Translator (NPN) 2SC2482BK | ||
| e702 | 203x0834-061 | 10 UF, 100V Electrolytic | ~ 362 | 200X4580-802 | ._ Transistor (NPN) 2808068 | ||
| 703 | 202X7050-248 | 1000 pF, 500V Ceramic | ant. | Makeaaooss | IG HATZ | . | |
| , | 1 | 200X2800-11 | STR381 | - |
SEMICONDUCTORS : : ;
| D203 | 201X2010-189 | Diode, 1S2078-27 | . | ||||
| 0204 | 201X2010-159 | Diode, 182076-27 | agi | _ | TRANSFORMERS & COILS | ‘ | - |
| 0208 | 201X2010-159 | - Diode, '$2076-27 | Goll, (RF Choke) | ||||
| 0208 | 201X2010-189 | Diode, 182076-27 | Goll, Horie. Size | = | |||
| 0207 | 201X2010-159 | Diode, 1S2076.27 | Goll, Adg. | ||||
| 0208 | 201X2010-159 | Diode, 1$2076-27 | Transformer, Hor. Drive | ||||
| J | 0209 | 201X2010-189 | . | HV-Unit M11 | |||
| : | o> | got | 201X2010-165, | “ei | £: | nie | |
| ' | 302 | _ | 201X2010-150 | MISCELLAN | _ | ||
| | | 0903 | 201x2010-159 | ‘ | ||||
| is | D308 | 201X2120-008 | ; | ||||
| 0308 | + | 201%2120-000 | . | ||||
| i | 0308 | 201X2010-159, | |||||
| ‘ADsot | 201X3120-218 | _ |
D502 201X3120-216
| ; | 40503 | 201X3120-216 | a: | |
| .* | ADSO8 | 201X3120-216 | THOT | 201X0100-112 |
Doo povetao2i8
| 1 | . | . | ||||||
| & | D701 | 201X2190-234 | wee | FINAL ASSEMBLY PARTS | ~ | |||
| : | 0702 | 201X2120-008 | Diode, RH AV | oo | § | a | ‘Pix Tube | : |
| : | 0201 | 200X3181-523 | _ Tranelator (NPN) 28C1 | ‘Assembly | ||||
| be | ave | 200x3181-523 | ~* | Transistor (NPN} | * | ; | a | |
| Br | 9203 | '200X4056-260 | Transistor. | fs | ||||
| i | 204 | 200X4056-260 | Traffaistor’ | 1 | ing Coll Unit” | = | ||
| 208 | 200X405€-260 | Translator (PNPY | TM | : |
SEMICONDUCTORS - )"28C2088LB a 28C2068LB
; 2
| ‘ | 203X6800-741 | a | ome | ; | - |
203X8600-741 2.7K Ohm, 5% PRRRDRCEETESEEIEREEEEELE
| 204X2116-014 | * | 500 Ohm, -B Semi-Fixed |
204X2115-014 500 Ohm, -B Semi-Fixed 204X2116-008 204X2115-008 a (204X2118-006.
} -
rc
amen ve noe
re wane + -| 5, nena tive oeme 69 cul [7_x903 exam Lamiten 254673 aye | e0s seam r Me | poqqaac or atcices
a ‘901 POWER DRIVE 2sc 2660 ‘ 902 ERROR AMP, 2SC1890
- <<
re
U-1133A, PRIN PCB ASSY :
- ee ee XTOL X-RAY PROTECTOR — = BacaDeC or 2801605 Geese or Hiczeioen tsoeee or 280620
Xi03 end X108 VIDEO AMP, 28C484C X104 end XIO6 VIDEO AMP. 25A075C SS maT St
fa ene wearen
00-4147-04 G07-CBO Schematic Notes Unless otherwise specified Resistance: (92) (K--K., M--MQ&), 1/4 (W) carbon resistor Capacitance: 1 or higher—> (pF), less than 1-> (yF) -—” working voltage - 50 (V) ceramic capacitar Inductance: ¢ H) Electrolytic Cap: Capacitance Value (F)/working voltage (V), . NP -> non-polar (or bipolar) electrolytic cap. Refer to the parts list for additional component information.
2 "indicates test point connection
hy indicates chassis ground uniess otherwise specified
Hz — indicates cycles per second For safety purposes (and continuing reliability) a replace all components marked with safety syrnboi with identical type.
Outelde of the P.C.B. Ass'y Description Picture Tube 19” AsDefiection Yoke PC Magnet . : AsFiyback Transf. AHVR ONE Resistor 2209,25W K C Capacitor 150pF, AC1.5KV Si. Transistor Si. Transistor
- Screw #8-%
- Screw. % x % Pix Tube Mtg. 4) Pyramidal Lock Washer (4) Nut Retainer, Pix Tube Mtg. (4) Clip — P.C.B. Support Standoff Wire Terminal (Gnd. Strap) Terminal Lug (Gnd:) Groundstrap Assy. Grounding Spring Wire Hook (Gnd. Strap) Purity: Shield Holddown Clamp Support Brkt. RH Support Brkt. LH Chassis Base Yoke Wedge (3)
Purity Shield Ass’y. Parts List
_ BeT1, DE12 . Description Degaussing Coil Rectifier 1 Amp 600V 2) ~ Pin Terminal (2)
cot Re21 Pin Terminal Housing Purity Shield (2 pes.) © Purity Shield (2 pcs.) Capacitor 100nF 10% 400V Resistor, Wirewound 332, 4W. Fire Retardent Term. Strip 4 Lug, CRT Socat PB. Ay (8U-20824) Parts List
Symbol 3105 3106 R3113 3114 R315 R316 3117 R3118 R3119
cai2t
Symbol C3107 C3108
Colle
L3101 Description _ ov R 200 Vv. R 200 v R SK: Vv R 5K Nv ‘R 5K OM R 10KQ2W J _ OM R 10KQaW OM” R 10KN2WI Comp. R‘ 3.SK2%W K Comp. R. 3.3KQ%W K . Comp. R3.3KQ“WK
Description :
- ° Cap. 10uF 260V.A C Cap. 1000pF 0C1400v P
Description Peaking Coil Part Number 17-7198-03 A20778-D = 21-141-01 A75034-B = 29-32-01 ,A29951-B A\46600-A QRF258K-221 QCZ0101-005 280870 2SC1106A 31-610818-06 31-601418-12 33-255-01 33-494-01 33-629-02 33-670-010R-02 334-228-903 34-33-04 34-574-02 35-212-03
Part Number QEWS3EA-108 QCZ9001-102M
Part Number QQL043K-101a
REPLACEMENT PARTS LIST - ELECTROHOME 19” MONITOR |
Components identified by the A symbol in the PARTS LIST and on the Schematic have special characteristics important to safety. 3 . DO NOT degrade the safety of the set through improper servicing.
" Abbreviations for Resistors and Capacitors Resistor : . Capacitor
| CR | : Carbon Resistor | C.Cap. | : Ceramic Capacitor |
| Comp. R | : Composition Resistor | ‘M.Cap | : Mylar Capacitor |
| OMR | : Oxide Metal Film Resistor | ECap. | : Electrolytic Capacitor |
| VR | : Variable Resistor | BP E Cap. | Bi-Polar (or Non-Polar) |
| MFR | : Metal Film Resistor | . | Electrolytic Capacitor |
| CMF R | : Coating Metal Film Resistor | MM Cap. | + Metalized Mylar Capacitor |
UNF R : Nonflammable Resistor PP Cap. :. Polypropylene Capacitor
| FR | : Fusible Resistor | : | MPP Cap. | : Metalized PP Capacitor |
PS Cap . 3 Polystyrol Capacitor. Tan. Cap.” : Tantal Capacitor.
replaced by those having identical Specifications. :
SERVICE REPLACEMENT PARTS LiST
Symbol ion. Part Number
j Man PC B. Ass'y : : “SU-1133A
| CRT Socket P.C.B,-Ass'y, | . | . | SU-3032A |
Purity Shield ‘Ass'y ns
| a | ao | Description |
: Part Number °
| . | X3101 | ‘ | Si. Transistor | 28C1514VC |
| —_ | x3102 | Si. Transistor | . | 2SC1514VC |
| . | X3103 | Si. Transistor | _ 28C1514VC |
~
| aA | ASCRT Socket | ‘A76068 |
Main PCB Ass'y (SU-1133A) Parts List
| ~ | Resistors | : | |||||
| : | R1406 | . | . | R 2002 “ | QVZ3230-002 | ||
| R1408 | v | R_ 2002 | . | QVZ3230-00°. | |||
| - | +1410 | CMF R 68f1WJ | QRX019J-6RE | ||||
| gS | R1414 | OM R 33KQ1IWJ | : | . | QRG019J-532 | ||
| : | R145 | OM = R 27KQIWJ | : | QRG019J-272 | |||
| R1421 | OM .R -12KQ2WJ | QRG026J-123Z | |||||
| 7 | 1422 | Vv | R 10KQ | : | QVZ3230-014 | ||
| - | AFR1401 | : | . AF | R 6802W K | . | QRH024K-680M | |
| 4A1503 | ° | ACMF R 11.8KQ“W he | QRV142F-1182 | ||||
| > | *R1504 _ | : | Vv | R 5KQ | ae | . | QVZ3230-053 |
| . | R1508 | OM = R 10KN2WJ | QRG026J-103Z | ||||
| r | R1512 - | “OM — R B2KQ2W A | - | . | QRG026J-822Z | ||
| eo, | _ .R1514 a | OM _R .82002WJ | QRG026J-821Z | ||||
| - | “ISIS | i | CMF R B221WJ | . | > QRX019J-8R2 | ||
| R1522 | CMF R 4721WJ | ' | QRX019J-4R7 | ||||
| rm | R1523, | OM = R 68N2w J | QRGO26J-680Z | ||||
| R1528 | OM R 39021WJ | : | QRG019J-391 | ||||
| loon | R1534 | - | zN OR. | ERZ-CO5ZK471 | |||
| VR1501 | a | ZN OR | . | ERZ-CO50K271 | |||
| | oo | 4R1703 | . | ACMF R 392%W+1% | QRV122F-3802 | |||
| AR1704 | : | ACMF- RR 7.68KQ UW +1% - | QRV142F-7681 | ||||
| jos. | 481901 . | AsPosistor | . | A75414 | |||
| R1902 - | UNF R 227WK | . | QRFO76K-2RO | ||||
| r | R1903 | CMF R 4723WJ | ‘ | : | QRX039J-4R7 | ||
| . | . | R1904 | : | OM ==R 10KQ2WY - | “ QRG026J-1032 | ||
| a | R1905 | OM OR 18KQIWI. - * | QRGO19J-183 | ||||
| : | 401908 | ACMF R 4724W+1% | QRV122F-470Z | ||||
| rot | ~ 2SR1909 | v | RA 2kQ | QVPSA0B-023E | |||
| % | . R1910 | ACMF «RR 2.74KQ2Y%W +1% | . | QRV142F-274) | |||
| oF | ASFR1901 | AF | R 2202%W K | QRH124K-221M - | |||
| Symbol | Description | . | + | Part Number | |||
| LZ | . C1301 | : | BPE Cap. 3.3uF 50V A | mS | : QEN61HA-335Z | ||
| 1402 | Tan. Cap. 2.2uF 16V K | QEES1CK-2258 | |||||
| r | 1407 | E, Cap. 4.7uF 6.3VA | + (QEWS1JA-475 | ||||
| : | 1411 | E' Cap. 100uF 160V A | QEW52CA-107 | ||||
| _ 01492 | " E Cap. 3.3uF 160V.A | QEW52CA-336. | |||||
| 1508 | PP. Cap. 5600uF 50V J . | QFP31HJ-562 | |||||
| a | 461512 | ANPP Cap. 2000pF DC15900V J. . | QFZ0082-202 | ||||
| : | 461513 | APP “Cap. 2000pF DC1500V J | QFZ0082-202 | ||||
| - | » C1814 | AXPP Cap. 2000pF DC1500V J | - | QFZ0082-202 | |||
| C1515 | PP Cap. 0.53uF DC1200V J | QFZ0087-534 | |||||
| = | C1520 | BPE Cap. 3.3uF 50VA- | oo | = QEN61HA-335Z | |||
| a | C1523 | . | E _ Cap. 1uF 160V A | : | QEW62CA-105Z, | ||
| C1824. | M_ ~ Cap..0:1uF 200V K | . | QFM720K-104M | ||||
| Los | . 401531 | oo | ASPP_ Cap. 2000pF DC1500V J | QFZ0082-202 | |||
| - | 401532 | APP Cap. 1500pF DC1500V J | QFZ0082-152 | ||||
| C1904 | E Cap. | QEY0034-001 | |||||
| 1905 | E Cap. 10uF 250V A | QEWS2EA-106 |
Symbol L1502 11503 1504
Transtormers ‘Symbol 71501 T1503
Semiconductors sy 101501 X1101 X1102 X1103 X1104 X1105 X1106 X1301 X1302 X1303 X1304 . X1305 x1401- X1402 X1501 X1901 x1902 1101 01102 01103 01301 01401 1402 D1503 01504 01505 01506 biso7 ot Api701 401901 401902 4D1903 AD 1904 AD1905
AXF1901 ANF 1902 Description Linarity Coil Width Coil Heater Choke
Description Hor. Drive Transf. Side Pin Transf.
Description Ic Si. Transistor Si. Transistor Si. Transistor Si. Transistor Si. Transistor Si. Transistor Si. Transistor Si. Transistor: Si. Transistor . Si. Transistor Si. Transistor Si- Transistor Si. Transistor Si. Transistor Si. Transistor Si. Transistor Si. Diode Si. Diode Si. Diode Si. Diode Si. Diode Zener Diode Si. Diode Si. Diode Zener Diode
Si. Diode Si. Diode AsZener Diode ASi. Diode ASi. Diode ASI. Diode © ASi. Diode AdZener Diode
Description AFuse 1.254 _ ANUL Fuse 3A Part Number 30835. 30380-A C30445-A..
Part Number - A46022-BM C39050-A
Part Number HA11244 28¢1685(R) 2SA673(C) 28C1685(R) 2SA673(C) 2SC1685(R) 2SA673(C) ” 28C1685(R) - 2SC1685(R) 2SA673(C) 2SC1685(R) - 2SC1685(R) > 28D478. 2SD478 2SC2610BK 2SC2688 (K.L.M.) 2SC1890A (E.F.) WO6A ~ WO6A WO6A 18Z473H 18Z473H RD10F(C) HF-1 VOoE AD11E(B) ‘WO6A 18881 18Z473H RD20EV2 181887A 181887A 181887A 181887A RD6.8EV3
Part Number QMF53U1-1R25S QMF66U1-3R0S ay
a
eo ones
Igo powen REoULATOR —_— oO yy SU-N034
MAIN PCB Assy
go Ean promecron 2eisar PEE aca are conn soon 2SC2611 or 28C26i0BK
/AWE XI01.X103 end XI08 VIDEO AMP 28C484C w 281605, <1 xi02.X106 end X106 ¥IDEO_AMP. 26A673C
pep peaes PoE | NEF ert Socket cont Rt al PCB, ASSY | . ron a0-103 (8)
Hi rt
x41, xa 2 Oo ve
no . wn TE Schematic N Pa eR Unless otherwise specified Resistance: (2) (K->K2.,, M--MQ2), 1/4 (W) carbon resistor Capacitance: 1 or higher-» (pF), less than 1-> (yF) working voltage -» 50 (V) ceramic capacitor Inductance: ’H) Electrolytic Cap: Capacitance Value (F)/working voltage (V), . NP — non-polar (or bipolar) electrolytic cap. Refer to the parts list for additional component information. 9: - indicates test point connection _ m, - indicates chassis ground | uniess otherwise specified Hz indicates cycles per second For safety purposes (and continuing reliability) 4 replace all components marked with safety symbol with . te identical type. 7 "NOTE: FR - fusible resistor —e23-" ve ca we aren
Parts identification in circuit boards:
e.g. SU1126A (R107 = R1107): SU3030A (R113 = R313)
“Main P.G.8, Ase'y (8U-1103A) Parts List
Symbol R1406 R1408 R1410 | 2 RIG “RI41S R1421- R1422 AFR1401 .ANR1503 R1504 R1508 R1511 R1514 R1515, R1522 1523 R1528 R1534 . VR1501 4&R1703 ASR1704 4sR1901 R1902 1903 R1904 AFR1901 Capacitors Symbol 1402 C1411 C1412 C1508 C1511 AC1512 AC1513 . 4e15614 C1515 1620 C1524 C1904 C1905
- 4C1907 Collis
11501 1502 L1503 11504 11901
Transformers
T1501 T1503 Deecrigtion “VSR 2002. VR 202 CMF R. 6821W J” OM A: 3.3KQ1WJ OM A 27KQ1IWJ OM FR -12KQ2W J VR 10KQ- AF FR 68Q22wK ASCMF Fi .11.8KQUW +1% VR 5K OM. R 10KN2W J on OM R 5S.6KQ2W Jd OM R. 68022W J CMF R’ B2Q1W J CMFR 4.791WJ OM R‘5622WU OM -R 30001WJ° ZN. R . ZN. OR, ACMF A: 30K Q4W 41% ACMF R7.68KQYUW +1% r : UNF R 2Q7W K . CMFR 5623W.J" OM A 10KR2W J AF R 2202%WK
Description :
Tan.Cap. 2.2uF 16V K E Cap. 100uF 160VA E Cap. 3:3uF 160VA PP Cap. S600pF 50V J E Cap. 47uF 160V A APP Cap. 2000pF DC1S00V J APP Cap. 2000pF DC1500V:J APP Cap. 2500pF DC1500V J PP Cap. 0.83uF DC1200V K BPE Cap. 1uF 50V'A : M | Cap. 0.1uF 200V K E Cap. E Cap. 10uF 250V A AMM Cap. 0.1uF AC150V Z
Peaking Coil” Liniarty Coil Width Coil 7 Heater Choke a Line Filter
Description Hor. Drive Transf. Side Pin Transf.
8-20 QRH124K-221M
” Part Number QEES1CK-225B QEWS2CA-107 . QEWS2CA-335 QFP31HJ-562 a ee ee ee ee
ee ‘ilssch nei eae
REPLACEMENT PARTS LIST - ELECTROHOME 13” MONITOR |
Components identified by the A -symbol in the PARTS LIST and on the Schematic have . special characteristics important to safety. — ; DO NOT degrade the safety of the set through improper servicing.
Abbreviations. for Resistors and Capacitors
| CR | : Carbon Resistor | GCap. | — | |
| . Comp. R | * | : Composition Resistor | M Cap . | |
| OMR | : Oxide Metal Film Resistor | . ECap. | © | |
| VR | - | : Mariable Resistor | BP E Cap. | |
| MFR | * | + | Metal Film Resistor | : |
| CMF R | : Coating Metal Film Resistor | MM.Cap. | © | |
| UNFR | - | : | Nonflammable Resistor ~ | PP Cap. |
| FR | : | Fusible Resistor | MPP Cap. |
. PS Cap Tan. Cap. : Ceramic Capacitor :. Mylar Capacitor Capacitor : Electrolytic : Bi-Polar (or Non-Polar) Electrolytic Capacitor . 1, Metalized Mylar Capacitor : Polypropylene Capacitor : Metalized PP Capacitor : Polygtyrol Capacitor : Tantal Capacitor
" Symbol
Outside of the P.C.B. Ass'y
- Symbol Avo1 Apy01
AA AROS Aco4 x01 tco1 Lo1
WA _Deseription Main P.C.B. Ass'y . CRT Socket P.C.B. Ass'y
Description AsPicture Tube A\Defiection Yoke PC Magnet Wedge AFlyback Transf. AFocus VR UNF Resistor 2202, 25W. K AC Capacitor 160 PF, ACT KV Si. Transistor | IC Regulator Degausing Coll Degausing Coil Pin Terminal (2) Degausing Col Pin Terminal Housing Groundstrap Ase'y. Groundstrap Wire Terminal Groundstrap Spring (2) Support Bracket RH Support Bracket LH SCREW 10-% Pix Tube Mtg. (4) Pyramidal Lockwasher (4) _Clip P.C.B. Support (2) Ground Lug Chassis Base
“8-19 Part Number SU-1103A SU-3016A
- Part Number 370ESB22(E) 29123-V A76366-A 30008 A19183-A A46606-A QRF258K-221 QCZ0101-005 2sD860 STR383 21-1007-31° 34-708-01 34-709-01 34-607-04 34-28-03 35-3560-01 36-3919-01 36-3019-02 31-631018-08 33-255-01 33-629-02 34-33-04 38-452-01
01503 ~ 01504 01505 11508 01507 01508 401701 401901. AD1902 “401903
- 401904
Miscellaneous Symbol 4F1901 AF1902 Description -
Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor
Transistor
- Transistor Transistor Transistor Transistor Diode Diode Diode Diode Diode LELLLLLLELLALLLLL LEDS
Si. Diode . Si. Diode - Si. Diode AdZener Diode ASI. Diode ASI. Didde ASI. Diode ‘ASI. Diode
Description Afuse 1A ANUL Fuse 3A Transistor ~ Part Number HA11244
28C'1685(R) 28A673(C) 28C1685(A) _ 2SA673(C) 28C1685(R) - 2SA673(C) 2S01685(R) 2S01685(R) 2SA673(C) 28C1685(R) 2SC1685(R) 2sD478 280478 2SC2610BK 2SC1685(P-S) WobA WO6A WO6A 182473H 182473H RD10F(C) HF-1 Voge ROTIE(B) WO6A -18S81 182473H .RD20EV2 "181887A 1S1887A 1S1887A 181887A
Part Number “QMF53U1-1RO0S QMF66U1-3R0S
CRT Socket P.C.B. Ass'y (SU-3016A) Parts List -
Resistors Symbol R3105, R3106 R3113 R3114 A3115, R3116 R3117_ - R3118 R3119 R3120 R312
Capacitors Symbol 3107 C3108
Cols Symbol | isi01
Semiconductors Symbol . ~ X3101 X3102 X3103 Miscellaneous Symbol A R 2002 R 5KQ R 5KQ R 5KQ R 10K22W J R .10KN2W J R 10K22W J Comp. R 3.3KQ2%W K Comp. R 3.3KQ*%WK Comp. R 3.3K Q%W K
Description . € Cap. 10uF 250VA C Cap. 1000pF. DC1400V P
‘Description _ Peaking coil’ -
Description Si. Transistor Si. Transistor Si. Transistor
Description ASCRT Socket
8-22
ics and Wiring Diagrams
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
egg ead \3 x
, DNION3d “Lyd * SAMISIY oanvin 1 AVMGIN ATIVA 29619 91 €0-SEr18-bB0¥ NVW-OVd 83dNS Oa “‘O'd O3UIA
Baty | MIDWAY MFG.CO.
MOS! - 00316 CROSS R oe SS ee et
DESCRIPTION
100 PF AX. CER: 470PF" "
MF" ( MFAX. TANT. 470 MF AX. ELEC.
82 OHM I/4W 5% CREN foo " 220 " "oH ow 470° sm 1K" om owe
et
1 9 POS SIP
QOXX CUSTOM IC
| O4xx | * | : |
Ox *
| xXx | " | “ |
fexx oo"
74LS00 * 74 L804 74 LS 08 74810 748 20 74LS32 74.874 74.886 74.8138 74S 157 74 L816)
74.8 248 7418 273 74.8 208 7418365 74.8 368 7418 377 74 L8'3768
BP~ROM SPV-6 (S$P)-5) PROM SPV-1
BP-ROM SPV-3 (SPI-4) PROM SAV-2 BP-ROM SPV-4 (SPI-6) PAL SPV-5 (SPI-7)
N58725P 2148 STATIC RAM
FERRITE BEAD QTy
sua
o y
@--w-w----
- rr Ne
16 PIN ic SOCKET 20 PIN " . 24 PIN " *
| 28 PIN " | " | 4 |
50 PIN CONN
| WUPIN | " | KK-156 |
RT ANGLE *
scRW
SUPER PAC-MAN VIDEO PC. ow-¥ EFERENCE LIST
DESIGNATION.
Ct3-cis cu. ci2
cPpr-cp4e Cl-ce C10
R52 R (4, R50, R5I,R53,R54 RS,R8, RIO R4,R7, RO RU-R3, KG, RI RIS, RIS-RI7 RI8- R21 ,R23-R4E R5S-R58
RMI, RM2
Ic 20 . ” OF a “ 2C "30, “34
Ic 4B
“4K “IL, IM, IN, 2L, 2M,2N “VE, IH, fy, 1K 10,34 4. “ 3M,3N “ 28
IC 26,26, 2u,2K "4M, 4N
FeI-FB4
1S 3L,40,46 “40 “26, 2H,20,2k:3¢ " 2C,20,2F, 3D, 3F ,3u PL vt
PCMH - PCMH4
A080 - 91435 - C36 0508 - oven 0550-0080:
0508 - 0060. 0935- 0081 0550~ cosoc
0062-10483 0062-11083 0062-13383 0062-1568: 0062-1798
0062 - 1956:
0508 -00°.
966 -001C) 0066 - 003¢: 0066 -006¢ 0066-018) 0u66 -a19¢
0300- 0080: 0300- 0080: 0300-0080: 0300-0080: 0300-0080 0300 - 0080: 03p0- 0060! 0300-0080: 300-0080: 0300 - 0030: 0300 - 0080
0300-ovses 0300-00803 0316 - 0080; 0316 - C080 0300-0080: 0316 - 0080: 0316 - 0080: 0316 - 0080 0316 - 0980:
0316 - 00802 0316 - 00803 0316 - 00802 0316 - 00803
9508 - 0080 0550- 0080
0316 - 008¢
0508-00801 0550-0080« 0508-00804 0508-00804
0300 - 00804
3000-16387
0316 - 00700
| - | . | cana |
GNA
| IGNATYN | DESCRIPTION. | DESIGNATION, | DESCRIPTION | ||||
| NOT USED | tc 28 | Tals 74 | |||||
| 100: PF AX. CER | “20 | PAL (OLB SPC-6 (SPI-1) | |||||
| \ooo PF" | “2c > | 7418138 | |||||
| 22 MF AX. ELECT. | “20 | 214 STATIC RAM | |||||
| 24 | + | TOL ME AX. CER | “26,26 | 74 18 245 | |||
| : | 0047 MF" * | cart) | + | 7418367 | . | ||
| 5 | : | 1 | Me | “20 | 74 Us 74 | . | . |
| C28” | 1B MF AX. TANT, | “2K | 7418245 | . | |||
| ¢ | 01 MF AX. CER. | “2M | 74.18 289 | ||||
| ) | 22 MF AX.ELECT | “2N | - | 74s 367. | |||
| . | . | ato mF" | |” | : | |||
| we | 100 MF | “ | 1c 3A | 74 Ls 04 | |||
| it | MF AX. GER. | : | “38 | 74 LS 109 | - | ||
| 4.7 MF AX. TANT. | “36 | 74 Ls 32 | |||||
| cat | 390 -PF AX. CER. | "30 | 74.8 16) | ||||
| r-cez,cea-c8 | oi} MF | : | “seo. | 74 18187 | |||
| , | avo MFO” | “3, | 74 18287 | ||||
| yore | . | 47 | PF | . | "39 | 74 LS 158 |
“3m 3L * STATIC. RAM MB8148-55/L-55
| | cPas | 1M AX: CER. | sau. | BP-ROM SPC-4 (SPI-3) | |||
| Loe | . | “3m. | 18 XX CUSTOM IC | |||
| . | | | NOT USED | : | |||
| . | 1K OHM 1/4 5% CREN | : | . | . | ||
| Woo Oe | ee | : | ||||
| eRS | howe | 1c 4a | 7aLs36e | _ | ||
| sso" | . | ars | +) | 18 XX CUSTOM IE | ||
| Nor vseD | sac | + | gexxcusToMic. | .- ° * | ||
| ' | 30" | . | "ae | + 748187 | : | : |
| ' | . | amen om | ons | “4F | 86XX CUSTOM IC | |
| °. | *" | woe | van | + | 74 ts 04 | |
| 1 | ark | ne | ® | tae | be | 6 |
| 2 | oak | eee | wae | a | ||
| 3, R14 | 1K | woe | "am | |||
| re | 22K | oe: | ||||
| 16 | tK | os | 1d 5N | : | ||
| 7 | wk | see | peas | * | ||
| ie | 33K | Se | a2 | FERRITE BEAD | = | |
| 19 | 1K | nee | : | : | ||
| 20 | fee" SO" fs 16S 1a | : | 40 PIN IC SOCKET ,- | |||
| 2 | BetC IN | vo | wo | |||
| ee: | “8 | “oK | 24PIN | TL | ||
| 23 | . | moe | 40 PIN |” | ay | ||
| 24 | . | an | > 20pIN sf | |||
| 126,R27 | oof | . | 2B | zorpiIn" | "| | * |
| 126 | . | “aN | zee" | : | ||
| 28. | “4B | eerin | . | |||
| (20° | 7 | "40,46 | ra) | |||
| 130°. | “oom | iePin" | * | on | : | |
| 131,882,238 | : | are | ||||
| 134 | . | anon otf | a | 5 9 PIN KK-186 STR.W/>PIN ® EXTRACTED | ||
| 138 | zee sm | Nf | 2 | 2oriN | ||
| 1368 | | thom mm | s3 | jopn 8 | HO | BRM | |
| 37 | ao | nM | . | on | ||
| ase | Ye | : | . | |||
| R39, R40. - | hk | me | pt | ot | 50 PIN RIBBON CONN. (CABLE ASBY) | |
| RAI R42 | + Bek" | —— | ~ | CABLE ASSEMBLY | L | |
| Ras | WOT USED | - | 2 | |||
| beyer yy ae | 100 | so. -PeMMi-PCHMS | P.c. BD. SPACER | |||
| AML RMS, | 47K OPINSIE 8 | peunse Fanaa | Ber | . | ||
| RM 4 - RM | 22K" " 4 | 7 | : | |||
| 7 | 5N | MOUNTING HARDWARE, | ||||
| aur | 22K 9 | eo: | = | “(2) 4-40 HEX NUTS | ||
| aMa, | 22k5" 7 4 oO | “(2) 4240 XO SLT. PAN MS | ||||
| RMIO, RMIT | 22Ke" 5 4 | : | 12) WSH. 4 125--280~ 032 FLT.ST. | |||
| amiz | ie | be | 1(2) WSH.4 120 -.250- O18 EXT. ST. | |||
| RMI, RMI | 22k 8 | “a | : | |||
| RMS | kK 9" " 8 | . |
RMI6 area." "8"
| ves | . | swt | 6. swiTcH | |
| awir | KS | ‘ | (SW2, S03 | POS. DIP SWITCH |
vets 1k OHM POT
| o. | INg48 | X-TAL | 432 MHZ CRYSTAL | |
| al | ' | 2n33918 | ||
| rc ia | . | wc 68A0RE CPU (1 8 MHZ) | noec-91438-F31 | SUPER PAC-MAN CPU BD. |
| oar) | EPROM SPC-! | : |
wie eprom SPC-2
| ra | NOT USED | : | : |
| ard | 74 US 367 | : |
= iF 7418 245 iW 7418 367 on | NOT USED ee EPROM SPC-3 Parl Mc 6BACSE CPU (1.5 MHZ) iM PAL 10L8 SPC-5 (SPI-2) whe (07 XX CUSTOM IC* Bally | WIOMIAY MFG. CO:
PART WO ASSEMBLY DWG. MOSI- 00316 - F008 SUPER PAC-MAN CPU BD. A0B4-91430.- F316 rar reggne
4 i
lal itl
DESCRIPTION Qty
| . | 186.432 MHZ CRYSTAL ’ | — |
| i | SUPER PAC-MAN CPU BD | ' |
i ENTE ERO: a oe
| : | 16-91N 1¢ SOCKET | a |
| ‘i | BOPIN 1C SOCKET | 2 |
- aqpin” rn rl oe ry
sstecnape >
Pope rrtrnrnrrne eee
| “ | : | GROSS | REFERENCE LIST |
QTY DESIGNATION.
| : | : | DESCRIPTION. | |||
| + | 100 PF AX.CER | ce | |||
| . | . | ent BOO BB | 3 | 4 | Sa4-ca7 |
| a7 | PF | ' | 690, | ||
| 1000 aF | t | cs | |||
| oos7 wr" | ' | 25 | |||
| ome” " | 46 | C6-C24,620,C62-C82,C84- C87 | |||
| 7 | MPO" | a8 | €26,C83,cP!1-CP46 | ||
| 18 MF AX. TANT. | 2 | c27,c2e | |||
| ea | 10 | C34-C43 | |||
| 220 MF AX. ELECT: | 2 | 64,030 | |||
| oo wR | 1 | 32 | |||
| 220 MF" | 1 | c3l. | |||
| 470 | MF" | . | cee | ||
| Igo OHM 174w 5% CRBN | 6 | R4a-Ra9 | |||
| 330 OHM 1/4W 5% CRBN | 2 | RE, RE | |||
| 470" | 8" | . | 3 | 3, R30, R37 | . |
| tk" | * | 1s | R2,R4,R5,K10,R15,RI4, |
. RIG, RI9,R29,R31, . R32,R33,R36,K39,R40
| rcs | 22K" | "tN | 6. | R12,RIS,RZO,R35, R41, |
R42
| ° | eee | oe | a7k | oT | nt | 3 | RU, R34, 838 |
| 7 | 1K.” | " | 7 | 1 | R22 | ||
| we" | - | “ | i) | RI7 | |||
| noway Mee | CO | om | se | ||||
| aunestaveo” \co23 | 22k * | noe | 2 | R23,827 | |||
| a | a | 33K | 2 | 26 | |||
| ~ | ~ | amK | at | “ | 2 | RO, R25 | |
| . | 100k " | “ | " | 1 | R24 | 7 | |
| — | * | “1K > ® PINS1.P.8 POS. | 2 | RMIZ, RMS | |||
| oy ar | ee | ee | 1 | RMI7 | |||
| : | ew | - | 2.2K BPINSIR 4 FOS | 4 | M4 RMB, RS | ||
| poes-prase-raie S22. ¢ | yo. crss | gine | a | : | Sur nue | |||
| + cpse | P33 | crs4 | wn | zeK 6" | a | 4 | RMIO, RMIT, AMIS, RM IS |
| a | ayx a” | e* | 4 | RMI-RM3, RM IS. | |||
| . | TK OHM POT” | a | VRi | ||||
| \UPER PAC-MAN CPU | BD... | a NES | ‘ | Br | - % |
fear baz S88,
| * | + | BN33818 | f | a | |||||
| oe | 74 S08 | 1 | ” ria ? | : | * | ||||
| = | +415 32 | Hl | *3¢ 0° | : | . | ||||
| nie | cod | 2 | 2y,28 | “ | |||||
| — | 7 | 74 | i) | "368 | |||||
| . | 7 Ta | i | “20, | ||||||
| 23 | . | 2 | " 3E,4€ | ||||||
| 7A | 1 | “3 | |||||||
| " | 3 | ' | “30 | . | |||||
| 17 | * | ZE,F, 2K IF | |||||||
| £ | 7 | 2 | oeisw | ||||||
| 7 | ' | aM | |||||||
| 14 | n | su | |||||||
| 74 | 4 | EK 2H, | |||||||
| 7a 4 | 1 | “8A | |||||||
| . | 07 Xx CUSTOM IC . | oa | ic iN | . | |||||
| 18 Xx | _ | “ | t | “38 | ” | ||||
| wexx | "ot | 1 | 48 | ||||||
| epost ay cpelels | . | Boxxx | * | " | 2 | " aCar | |||
| 312] 81 21 SiS S1815| | aq | . | noe | ; | |||||
| arcnow | seg-4 (seins). | | | tc 3m | ||||||
| ge | gis | sl | ets | ROM | PGI | 1 | "Bw | . | ‘ |
| alsisialaleisialelaisl | asidal | . | To | geese | 1 | nie | |||
| : | : | sPc-3 | i | cae | |||||
| 7 | wa 3730 | Hl | in | ||||||
| $C BHAOSE CPULI.5 MHZ) | 2 | + aate | |||||||
| PAL IOLE SPC-S | (SPi-2) | ™ | . | ||||||
| PAL lOLe SPc-6 | (SPix1) | ” 28 | . | ||||||
| STATIC RAM MBBI48-85/L-55 | 2 | " 3K3L | : | ||||||
| . | . | + | Teeoeee | 1 | “aL | aa | |||
| . | 214, §TATIC RAM | H | Pry | ||||||
| QESIGNATION, | =~ | PART NOS. | RIN CONN KK- 156 * | 1 | rT) | ||||
| - | pa | “ | 2opin | t | v2 | ||||
| X-TAL | | 0808 -00804-1400 | “opin | 1 | a3 | 7 | ||||
| zs | 50 PIN RIBBON CONN | 1 | a) | . | |||||
| A080. 91436-F 3 | . | CABLE ASSEMBLY | ‘4 | - | . |
MHICSN an
| + | : | 4-40 HEX NUTS: |
o9s2- do! x 0580-00804- 23 7 080§-00804- 0500 0508 -00804-0400~~ - “PC BD SPACER
| nag | Oe | ee es SORM ee | oe |
| ‘C508 -00804-"1B8O | : | : |
0508 - 00804-1900 . 8 POS. OIF SWITCH bo hh O18 SETEPAN MS. S MOUNTING HARDWARE.
{ WB. 4 128--260~ .O32 FLTST. 2 WSH.4.120 - 250-018 EXT ST. 2 a
: “2 t
PCMKi- POMH4 PCMHS-PCMHS-
swi, sw2, Sw3 . 0808-00800-0800 9318 -00800-0002 0318 -00800- 0003 0889-00800-2400 0580-00800-2200 98098-90800-0800
0508 - 00800-1400 0850 - 00800 ~!800
0062-1 1083 - Xxx 0062 -144B3-1XXX 0062-156 B3- IXxX )3= 1XXK
0062-196.83~ 1KXx
0062 - 21183 -1XXx “0082 - 227B3+1Xx1 0082-23182 IXx 0062-247 5d-1KX 0062 = 251B35 IKK 206 8'- 259B3 - 18H 062.- 27583 -1XX)
0508-00804: 0200 ‘0508 -00804- 0100 0316-00804 -000! 0808 - 00804-0301 0508 - 00804-1200 0508- 00804-1000
0508-00804-1300
(008 - 00801-0106
0508-00802 -020
0300- 00808- 0¢ 0300 -G0803- OC 0300, 008 03-0 0300-09803-00: 0316-00803 -00 0300 - 00803- 6¢ 0300 -00803 -0 0300. 00803-0 0300 -00803-0 0300 -00803 -0 0316 -00803-« [0316 - 00863 -« 0300 - 00808 -< 0300-00803 -¢ 0316-00803-q
0066-G06CK- KA 0066 -620¢X-X) 0086 -oRicK-x, 0066 -o22cx-x
0316 - 00803- 61 0316 - 00803- a1 0316 ~ 00803 - 01 0316 - 0803-01 9066- :88KX~ x) 0316 - 00803 - 01 0316 - 00803 - 01 0316 - 00803~ 0 0580- 00803 - 6 ‘0808 - 00803 - 8: 0508 - 00803 - 0
3900 - 1636740 3000 - 16367-2 3000 ~ 16367 -1¢
0300-00804-11 ‘4300-00020-0
0017-00103-00 0017 -.00101- 08 0017- 00104-00
- 0017+ 00104-0¢ 0316 - 00700-0i 0017 - 001010:
0300 - 0080408 052 -00804-1¢
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
CREDIT BYPASS BD. \ ROBZ = 91848 ~ COLD 1 wee CONN 2.
peeerrenrn tr vita = ouas, usw
ua omar une me
querer rr Pm bests ——s]
{ais}
a frre ~*~ arcrer aa pac sote fi
sc-5
E
a
/
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
n ra 7 HE : E :
OFxx + nydnay daz | ESTO ox Mgie ve - atid . aaET. 33) +
. D 1000 MF
{kt a
- ' to tan : in {St 1 cuss]
er “pase =e ate 7 mr “ = = owas pra n = us| ey, zy = a oe a = Ht Poa at a rm no re f =i
- - f at , oa HH ease eo ise <a sot
- : sean -
BETSSEESE E82 .
[eae | a A a a ANS A A dee ¢ | = aes ass { mle
Fs 510) ETS
ge ze 2 alee z EEE ai & aoe atta sgt = = oe 3 —4 N 9 n
1 iprvedorosekeret onan ds Desc Po Fatomieg da pe anne hay otk
ae L az 4 -s = i a ae
EO tg gt
tt net]
et
f {
Ft
rs
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.