Rip Cord
Rip Cord (Exidy, 1979) · Manual · 25 pages · 18 sections · original scan
“RIP CoRD
CONTENTS
T. GENERAL 2... cece cece cece cece eee e eee wee ee eee eee eee 3 II. NORMAL OPERATION
A. Attract Mode ..... B. Introduction Mode
III. SELECTABLE OPTIONS
A. Coinage ..... B. Jumps (Turns) C. TOP THIS SCORE
IV. AUDIO ADJUSTMENTS
V. POWER SUPPLY ADJUSTMENTS ........ ste sewe cece eeee +26
VI. MECHANICAL ASSEMBLIES
A. Control Panel woes eee cece cece rece eceees seen 7 B. To Service the D-Ring Control C. To Remove the Monitor sees D. To Remove the Logic Board .............
VII. TECHNICAL INFORMATION
A. Logic Description and Operation ..... B. Audio Description and Operation .. C. Diagrams, Pinout Table, and Schematics ....
ILLUSTRATIONS
Figure 1: Monitor Display ........... cee ee cece eee ee Figure 2: Audio Board Adjustments .......eccceeeeeee5
Figure 3: Power Supply Adjustments ........
Figure 4: Control Panel ..
Figure 5: D-Ring Control ..............-. re et:) Figure 6: Major Internal Components ...........e0005 9
Figure 7: Logic Board Block Diagram ............... 13
Figure 8: Audio Board Block Diagram ............ eee
Figure 9: Harness Diagram .............. see eee eee ee IS
I. GENERAL
RIPCORD is a one or two player skill game in which each player launches a parachutist out of a plane, opens the parachute, and controls the parachutist's drift. The players score points by landing the parachutist on a scoring platform (see Figure 1).
The plane that the parachutist jumps from flys right to left across the top of the screen, at a random height. A number of helicopters fly about the screen at random. If the parachutist hits a helicopter or misses a scoring platform, he falls into the sea. RIPCORD can be set for 3, 5, 7, or 9 jumps per game, but these jumps are not deducted until the player fails to score.
RIPCORD has three coinage options. Full instructions are displayed on screen after the player inserts his coins, and the day's high score is shown on screen. There is an optional "top this score" feature which gives a replay to the player who beats a random score.
PLAYER_ONE JUMPS PLAYER Two
Figure 1: Monitor Display
II. NORMAL OPERATION
A. Attract Mode
When the game is first turned on, the words GAME OVER will flash on screen. Also on screen will be TODAY'S HIGH SCORE followed by a score which changes with each new higher score attained throughout the day. When the game is turned off, the high score is reset to zero.
Also displayed on screen, at the operator's selection, will be one of the following:
Two Player - 1 Coin or One Player - 1 Coin Two Player - 2 Coin or One Player - 2 Coin Two Player - 4 Coin
RIPCORD also has a credit counter so that a player can buy a number of games in advance.
While in the attract mode (no credits, no game in progress) the game plays automatically.
B. Introduction Mode
When a player deposits a coin, the following message comes on screen:
PUSH JUMP BUTTON PULL D RING TO OPEN PARACHUTE JUMP UNTIL TARGET IS MISSED TARGETS INDICATE SCORE
CREDITS N
TOP THIS SCORE FOR CREDIT
M
Here, N is the number of games in the credit counter, and M is a random score used by the "top this score" feature. At the operator's option, RIPCORD awards one extra game to any player who matches or excedes the score M.
C. Game Play
When the START button is pressed (after coinage), a fanfare tune alerts the player that the game has begun, and the number of jumps (turns) per player is shown at the top center of the screen. This number is operator selectable to 3, 5, 7, or 9.
When the fanfare ends, the plane flys on screen. To launch the parachutist out of the plane, the player must push the JUMP button on the control panel. To open the parachute, he must pull the D-RING at the left of the video screen, After opening the chute, he can control the parachutist's drift with the DRIFT control knob on the control panel.
Each player trys to land the parachutist on one of the scoring platforms, using the DRIFT control. If successful, he continues jumping until he finally misses a platform. If he scores twice in a.row, he is eligible for a BONUS SCORE: the next jumps score ten times the normal amount. This bonus remains in effect until he misses a platform.
If a player scores several times in a row, the helicopters become more active and interfere with the parachutist. This tests the player's skill, since it is difficult to build up high scores.
III. SELECTABLE OPTIONS
RIPCORD has three switch selectable options. These are controled by a seven segment DIP switch located on the main logic board at position 14A (see Figure 4, item 8). This switch is accessible from the front of the game through the coin door.
| Following are the options and the | WHISTLE | -- 1 pot: |
switch settings for their selection: R16=volume A. Coinage switch switch
| 4 | 5 | MUSIC | -- 1 pot: |
| 2 Player - 1 Coin | ON | ON | R63=volume |
| 1 Player - 1 Coin | ON | OFF | |
| 2 Player - 2 Coin | TONE | -- 1 pot: | |
| 1 Player - 2 Coin | OFF | on | R65=tone control |
2 Player - 4 Coin
B. Jumps (Turns) switch switch 6 7
| 3 Jumps | ON | ON |
| 5 Jumps | ON | OFF |
| 7 Jumps | OFF | ON |
| 9 Jumps | OFF | OFF |
C. TOP THIS SCORE switch
Credit awarded for OFF topping score
Credit not awarded ON for topping score
IV. AUDIO ADJUSTMENTS (See Figure 2)
CHUTE OPEN -- 2 pots:
R60=low frequency
R39=high frequency
SPLASH -- 1 pot:
R29=volume
| SCREAM | -- 3 pots: | Figure 2: Audio Board Adjustments |
| R47=frequency | R16 WHISTLE | 6 R65 TONE |
R63 MUSIC 7 DIP switch
| R2 =modulation | R39 CHUTE OPEN | 8 R49 SCREAM |
R29 SPLASH 9 R2 SCREAM
| R49=volume | R60 CHUTE OPEN | 0 R47 SCREAM |
UW
POWER SUPPLY ADJUSTMENTS
Connect a voltmeter to the +5
- Adjust the power supply potentiometer for +5.0 + .1 VDC (see Figure 3). and ground traces on the logic board.
Adjustment potentiometer
Figure 3: Power Supply Adjustments
VI. MECHANICAL ASSEMBLIES 2. Reaching up through the coindoor, remove the wingnuts from the four A. RIPCORD Control Panel (see Figure 4) welded corner studs that hold the control panel down. The RIPCORD control panel is a single metal plate with four welded mounting 3. Lift the control panel up from studs. One potentiometer and three the cabinet and set it on edge, pushbutton switches are mounted on so that you can reach its underthe panel and connected to the har- side. ness with fast-on terminals. The panel is finished with flat black 4. Check all terminal connections enamel; if necessary, retouch with to the pushbuttons and the potflat black spray paint. entiometer.
To service the control panel:
- Open the coindoor.
Figure 4: Control Panel
Drift control knob Harness 2 player start Welded corner stud with wing nut Steel panel 1 player start Jump button Potentiometer BROWNS ord3du
B. To Service the D-Ring Control
The microswitch and lever spring are easily accessible through the back of the cabinet. You should not have to remove the control for service, but if you do, follow these steps:
- Unplug the power cord.
- Open and remove the back door.
- The triangular D-ring is held together by a grooved pin; the joint is covered with a length 4, of shrink Slide the and drive then pull remove it tubing (see Figure 5). shrink tubing aside out the groved pin; the D-ring open and from the lever.
Remove the front plastic panel from the cabinet by poping it out of its moldings.
From the front of the cabinet, remove the two hex-head screws which hold the control in place.
From the back of the cabinet, remove the control.
Figure 5: D-Ring Control
Microswitch Mounting bracket Pivot bolt Mounting screws Bons Lever D-ring Lever spring Tripwire
To Remove the Monitor
Unplug the power cord.
Open and remove the back door.
Unplug the harness connector from the monitor.
Remove the four bolts from the monitor chassis flange mounts.
Lift the monitor up and slide it out of the cabinet. To Remove the Logic Board
Unplug the power cord.
Open and remove the back door.
Clip the plastic tie wraps which hold the board in its rack.
Disconnect the edge connector from the board.
Slide the board out of its rack.
Figure 6:
1 Power supply (see Figure 3) 2 D-ring control (see Figure 5) 3 Speaker DIVE Major Internal Components
Fuse Interlock switch Logic PC board Audio PC board Coin counter
VII. TECHNICAL INFORMATION
A. Logic Description and Operation
RIPCORD is a microcomputer game which uses the 6502 central processor unit. (For more information on this processor, refer to MOSTEK publication #6500-10A, MCS 6500 Microcomputer Family Hardware Manual.)
This processor is unique in that it does not have a separate input/output structure, but treats all I/O as if it were an area of memory. Memory is mapped as follows:
FFF8-FPFFF Interrupt and reset vectors FOOO-FFF7 Program storage (PROM) D000 Drift control and Interrupt reset co0o Option switches (input) A000 Control switches (input) 8000 Parachutist rotation and audio control bits (outputs)
4000-43FF Screen RAM 3000 Parachutist horizontal position (controls) 2000 Parachutist vertical position (controls) 1000-1FFF Program storage (PROM) 0100-01FF Stack RAM 0000-00FF Base page RAM
Base page RAM holds variables while the game program is runniing; the stack RAM holds return addresses and important data during subroutines. The program storage PROM holds the program which controls the operation of the game.
The screen RAM consists of 1024 bytes (8-bit words) of read/write memory. When not being addressed by the processor, this RAM is scanned by main timing, to display a 32 x 32 matrix of squares on the screen. The data stored in the screen RAM is then used to select one of 256 images from the screen ROM (each image is 8 elements wide and 8 lines tall). Note that the processor never addresses the screen ROM directly. The 8 x 8 images selected from screen ROM fit together to form the display on screen. An alphanumeric character takes only one 8 x 8 image to display, while a helicopter, the plane, and the parachutist are each made up of several images.
Example:
To store the letter "X" in the upper left corner of the screen, the processor would write 29H in memory location 40008.
The same circuitry that generates sync and scans the screen RAM also generates the horizontal and vertical lines which form the box around the screen display.
The parachutist is generated by two sets of counters (horizontal and vertical) which are used to position the figure on screen. The outputs of the counters, along with the rotation information in 8000H, are fed to the parachutist PROM to form the parachutist's image. The processor controls the parachutist by preloading the counters to the desired position during vertical sync.
The processor reads data from the switches by gating the data from the control or option switches onto the data bus when the appropriate address is selected.
The drift control is an analog to digital converter which the processor reads to determine the hor— izontal position of the parachutist.
B. Audio Description and Operation (see Figure 8)
The audio board is powered by +5 VDC from the video monitor and +15 VDC developed on the audio board itself. The AC power source for the +15 VDC comes from an external transformer which steps down the 115 VAC line voltage.
The audio board contains the following circuits:
* +15 VDC power supply
- audio amplifier
white noise generator
chute open sound generator
splash sound generator
scream sound generator
whistle sound generator
music input
video inversion driver
Following are brief descriptions of these circuits:
The +15 VDC Power Supply
The first stage of the +15 VDC supply is a full wave rectifier which converts the input 35 VAC (center-tapped) to approximately +25 VDC. This later DC voltage is not critical, however, and may vary from board to board or transformer to transformer.
The second stage is a self-contained 3-lead regulator chip (LM 340T or equivalent) which converts the +25 VDC to +15 VDC. This +15 VDC source feeds most audio circuits, and the base of transistor Q1. This source is a relatively low current supply, so pass transistor Q1 provides a higher current at +15 vpc ffor the audio amplifier chips (LM 380N or equivalent). Transistor Q1 is configured as an emitter follower, so the emitter voltage will equal the regulated +15 VDC minus approximately .7 VDC (the normal drop across the base-emitter junction for a silicon transistor at or near saturation).
The Chute Open Sound Generator
This sound is triggered by a negativegoing TTL pulse from the logic board. The circuit comprises two phase shift oscillators, one tuned at a lower frequency than the other. The transistors in these oscillators (Q7 and Q12) normally recieve no base current, so the circuits do not oscillate.
Example:
The base of Q12 has no current path toward a positive voltage, since the anode of CR17 is pulled to ground by an open collector gate.
When signal 5 CHUTE OPEN drives the input of the gate low, the output is allowed to swing high, foward biasing diode CR17 and creating a current path through R62 to +5 VDC. This turns on the oscillator and charges capacitor C31. When signal 5 CHUTE OPEN disappears, diode CR17 once more is reversed biased, shutting off the current path. Since C31 is still charged, Q12 has base current for a period determined by the RC combination C31, R53.
Diodes CR11 and CR18 provide output isolation, while allowing the signals to pass on to the volume pots and then to the audio input bus.
The Splash Sound Generator
The Splash sound is triggered by a negative goining TTL pulse from the logic board. The input structure is is similar to the input of the Chute Open sound generator, in that transistor 96 receives no base current until the incoming signal 5 SPLASH forward biases diode CR7, creating a base current path toward +15 VDC, and simultaneously charging capacitor C15. When the input signal is removed, diode CR7 is once more reverse biased,
leaving the charged C15 to keep the circuit on for a period determined by the RC combination C15, R24.
This circuit, however, does not oscillate. It merely amplifies the white noise previously generated. Thus, it is like an amplifying switch with a small turn-off delay. A diode in the collector of Q6 provides output isolation as in the Chute Open circuit.
The Scream Sound Generator
The scream sound is enabled by a TTL low level input from the logic board. This generator consists of a voltage controlled oscillator (used as a tone generator) and an amplitude modulator used to shape the sound volume.
When there is no input signal, transistor Q11 is saturated, thus holding U4 pin 5 (the input to the VC) relatively low and U5 pin 2 (the control input to the amplitude modulator) relatively high. This voltage at U5 pin 2 holds the output OFF.
This would immediately rob Q11 of most of its base current and cause the collector voltage to rise, if not for the 6.8 uF capacitor in the upper half of the divider. This capacitor takes time to discharge, and thus the collector voltage rises gradually. This changes the VCO frequency gradually from low to high.
Since the emitter voltage is the amplitude control input to U5, this also enables the output of the modulator U5 in the same manner (except that a descending voltage increases the output amplitude). U9 provides additional modulation; R2 is the modulation control.
The duration of the input signal 5 SCREAM determines the duration of the scream sound directly. The output is fed directly to the audio input bus.
The Whistle Sound Generator
The Q4 - U10 circuit generates the whistle sound in much the same way that the Q11 - U4 circuit generates the scream sound. R16 is the volume control.
The Music Input
The music is generated entirely by the microprocessor on the logic board, out of software. The input on the audio board simply consists of an isolation and volume control network, prior to passing the signal to the audio bus.
The Video Inversion Driver
This circuit is used only in cocktail table models of RIPCORD, where the video display must be turned over in order for a player on either side of the table to see an upright picture when it is his turn to play. The circuit is a single D type flip-flop driving a transistor (MJE 182). When this transistor is turned on the collector drives toward ground, thus supplying the yoke relay with the ground it needs to energize and reverse the yoke leads in the video monitor.
The flip-flop U2 is set by a negative going TTL pulse from the logic board to U2 pin 2; this inverts the picture. U2 is reset by a negative going pulse from the logic board to pin 13.
C. Diagrams, Pinout Table, and Schematics
Data Bus
Audio Outputs Address Bus
Parachutist Position Counter Parachutist ROM Parachutist
Screen ROM
Control ROM Sync Generation Lines
Drift Control (A to D)
Figure 7: Logic Board Block Diagram
Figure 8 Audio Board Block Diagram
From
(Through logic board,
from video monitor)
sau ) 35 VAC Center-Tapped
5S CHUTE OPEN
+15 VDC
High
White Noise Generator +15 VDC High Current VCC Source (Used only for audio Regulated power am- Power Supply}+15 VDC Low Current plifier vcc Source LM 380's)
Frequency Oscillator Low
Tone Generator Voltage Controlled Oscillator Video Inversion Latch & Driver Frequency Oscillator
Sj plash Audio Sound Ampli- Generator fier Amplitude Modulator Whistle Sound Generator To video yoke relay eee
ff Ral
XFMR
35 VAC C.T. 1.5 amp
Figure 9 VY fa 115 VAC
Harness Diagram Vv SHEAaESEEEEE:
Monitor
GND Enable 0 GND Enable a a 8. Enable GND
Stary
Pin
gi-1
J1-2
J2-2
J2-8
J3-1
J3-2
J3-3
33-4
33-5
J3-6
- The static One end is Table 1 Wiring Harness Pinouts
Signal
Switched power
Power
Power line ground
Video
Video return
Power supply ground
Monitor speaker
vec
Power line ground
Monitor speaker
Switched power
Power
10.8 VDC
Switched power
Power
Power supply ground
35 VAC
35 VAC
35 VAC C.T.
vec
Ground
Video return Pin
J4-4
J4-5
J4-6
J4-7
J4-8
J4-9
J4-10
34-11
J4-12
J4-13
J4-14
34-15
34-16:
J4-17
34-18
34-19
J4-20
J4~21
J4-22 To
J2-1
J6-1
53-6
J3-5
J3-4
J5-1
J5-2 And
COINC Signal
Video
Player 1 start
Player 2 start
Jump
Parachute open
Coin drop switch
Static antenna*
35 VAC C.T.
35 VAC
35 VAC
Relay -
Relay +
Speaker out
Speaker out
Pot wiper
Speaker
Speaker
Coin drop switch
Power supply ground
vec
Coin drop switch
antenna is a six foot long wire bundled in the harness. the other end is free. connected to 34-13;
STE256 iflowe os
ia EL. Dal ape ee eS ee
mae PS wseeensen (td 0 EE pace maces
SMTEA B ae Spa a
NOTES
PAUL 7800 SERIES TR ARE LOW PoMER scHOTTHY EXIDY INC. RiP CORD LOGIC DIAGRAM | PAGE 10F7 | MASTER TIMING Ke 30-8014
NOTES READ. PRE Moo SERES TRLARE LOM POWER SCHOTTHY | EXIDY INC. RIP CORD LOGIC DIAGRAM | PAGE 20F7 VIDEO GENERATION R030 - 0014
7404_10F a 7 la BLvi0
NOTES TALL M0 SERIES ToL ARE LOW POWER SCHOTTRY EXIOY INC. RIP CORD LOGIC DIAGRAM | PAGE 30F7 MAN GENERATION [RC 30-0014
Rea-28
S00ITe palcaee lero?| = 1a :
(CED ao ROP
wor. c USEO- oP.
<> onan _* aR Ce STAAL TWO RAVER y coNwecroR
CED SAT One PuaveR 5 vo.ts a cal, it: ‘rouno {0 , a “XL «1 BYPASS EVERY 2 PACKAGES:
notes UML 7209 SERIES TTL ARL LOW POWER SCHOFTRY
- ALL RESISTORS AREI/4W ANDIN CHS 3 ALL CAPACITORS ABE IN MICO FARADS EXIDY INC. RIP CORD _LOGIG DIAGRAM PAGE 40F 7, INPUT / OUTPUT RE30 - 0014 I
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
6341 I aA
noTes, {PALL 7400 SERIES TR ARE LOW POWER SCHOTTAY EXIDY ING. RIP CORD LOGIC DIAGRAM_| PAGE 60F7 READ ONLY MEMORY RC 30-0014
resort 16a
TveMe Re 30-0014 L_.
EXIDY INC. RIF CORDLOGIC DIAGRAM PAGE 70F 7 {
4415 yours
aD PES a * ZL ony fi. seme ©98!_| $gtlow
i cc nd \ oRe VARI FROM asic ry xronmen § CB Ag pe =
CTA TAP 30
es Sov (Riles Be igor
15 vours weer
- q Res = ed
Z SPLASH
° +5 vous
| SPLASH DOO Ce sister, MIE 162
+15 yours i _ Vv
R35 ik A38. Hick
CHUTE OPEN
1 CHUTE OPEN | é
bes #8 Sion 9 notes y IS RESSTORS 296 OWS AND VAM UNLESS FEFERENCE DESI 2 AL cAENCI Tone Ae nc CARAOS AO MVOC FIRST USED] LAST USED [NOT USED WAC ESS OTHERWISE SPLOIED
43 C3I CRI CRIS CRESS @5,5,10 Rig, 22,27, VAI Vai j
EXIDY INC. RIP CORD SCHEMATICS PAGE 1OF 2 AUDIO KC30- 0015
+15 vouTs CRS smusic ish Ase ie
Pr or: "POT
ze Ger ci4 HIG ae Fisve
‘FEN care u? o43
as, cx | ew ‘ GP as kueas 2 SPLASH AA —} {WR a Ago ie
R30 Err} 1 CHUTE OPEN
5 CHUTE OPEN
K Ri2 a Bek: ‘04 23 2N3904 “a7
1 SPLASH —T