CATHODE RAY TOMES

Marvel vs Capcom

Marvel Vs. Capcom: Clash of Super Heroes (Europe 980123) (Capcom, 1998) · Manual · 16 pages · 18 sections · original scan

Page 1

MARVEL, CAPTAIN AMERICA, GAMBIT, INCREDIBLE HULK, SPIDER-MAN, WOLVERINE, VENOM, WARMACHINE, ONSLAUGHT AND ALL OTHER MARVEL CHARACTERS AND THE DISTINCTIVE LIKENESSES THEREOF ARE TRADEMARKS OF MARVEL CHARACTERS, INC, AND ARE USED WITH PERMISSION. ©1998 MARVEL CHARACTERS, INC. ALL RIGHTS RESERVED @CAPCOM CO., LTD. 1998 ALL RIGHTS RESERVED. ©CAPCOM U.S.A INC. 1998 ALL RIGHTS RESERVED. STRIDER HIRYU: ©MOTO KIKAKU ©CAPCOM CO., LTD. 1998 ALL RIGHTS RESERVED. THIS VIDEO GAME HAS BEEB PRODUCED UNDER LICENSE FROM MARVEL CHARACTERS, INC.

OPERATORS MANUAL

/\\ WARNING

This game is for use in the United States of America and Canada. Sales, export or operation outside of these countries may be constructed as copyright and trademark infringements and is strictly prohibited. Violators are subject to severe penalties and will be prosecuted to the full extent of the law.

CAPCOM” COIN-OP, INC. 475 Oakmead Parkway Sunnyvale, CA 94086 Phone: (408) 774-0500 PM00206 Fax: (408) 522-5331 010198

Page 2

° CAPCOM coin-op, nc. MARVEL VS. CAPCOM ™

THANK YOU FOR PURCHASING MARVEL VS CAPCOM ™ WE INVITE YOU TO USE THE FOLLOWING MAILING ADDRESS, TELEPHONE OR FAX NUMBER FOR PARTS OR SERVICE INFORMATION CONCERNING THIS GAME:

CAPCOM® COIN-OP, INC. ATTN: CUSTOMER SERVICE 475 OAKMEAD PARKWAY SUNNYVALE, CA 94086 PHONE: (408) 522-5325 FAX: (408) 522-5331

THE SERIAL NUMBERS OF YOUR KIT ARE LOCATED ON THE GAME CARTRIDGES AS SHOWN BELOW. PLEASE HAVE THESE SERIAL NUMBERS AVAILABLE WHEN CONTACTING US FOR SERVICE INFORMATION.

"B" CARTRIDGE AAMA SERIAL NUMBER SERIAL NUMBER

"A" CARTRIDGE SERIAL NUMBER (BOTTOM OF CASE) ‘vs00900

DEPENDING ON THE TYPE OF KIT YOU PURCHASED, PLEASE RECORD THE SERIAL NUMBERS HERE:

“FULL” KIT A-CARTRIDGE SERIAL # B-CARTRIDGE SERIAL # AAMA SERIAL #

“B” KIT B-CARTRIDGE SERIAL # AAMA SERIAL #

Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC.

Page 3

® CAPCOM” co-op, nc. MARVEL VS. CAPCOM ™

TABLE OF CONTENTS

Warranty Information

Kit nspection a eceseseseesesesesscscscscseeeescscseeeeseseesseseersasscstecseseeneneaeene 1

Cation =§-—§ => ————————————————Capbivusisgegiezneatrans osqeanopunaviegvons eg Soupensenesterasvaning sesteseovasnners 2

“FULL” Kit , “B” Kit Preparation Installation Control Panel Overlay Cabinet Graphics Re-assembly of Components Remote Volume/Test Switch Control Panel Wiring Game Cartridges RRA WW AW wy

Test Mode Test Menu Accessing the Menu How to Select an Item Closing the Menu Menu Item Descriptions ....Configuration Menu System Configuration Game Configuration

Wiring References JAMMA Connections Auxiliary Cable Connections

Reference Information Game Case Controls and Connectors Typical Control Panel Layout

[Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC,

Page 4

® CAPCOM” co-op, nc. MARVEL VS. CAPCOM ™

LIMITED PRODUCT WARRANTY (APPLIES TO DOMESTIC SALES ONLY)

CAPCOM® COIN-OP, INC. (Seller), warrants only to the initial purchaser of its products, that the items listed below are free from defects in material and workmanship under normal use and service for the warranty periods specified:

A. CPS II System Cartridges One (1) Year B. Electronic and Mechanical Components: (90) days

No other part of Seller's products are warranted.

Warranty periods are effective from the initial date of shipment from seller to its authorized distributors.

Seller's sole liability shall be, at its option, to repair or replace products which are returned to Seller during the warranty periods specified, provided:

A. Seller is notified promptly upon discovery by buyer that stated products are defective;

B. Such products are properly packaged and then returned, prepaid to Seller's designated plant.

This warranty does not apply to any parts damaged during shipment or handling, or due to improper installation or usage, or alteration. In no event shall Seller be liable for any anticipated profits, loss of profits, loss of use, incidental or consequential damages or any other losses incurred by the customer in connection with the purchase of a CAPCOM® COIN-OP, INC. product.

WARRANTY DISCLAIMER

EXCEPT AS SPECIFICALLY PROVIDED IN A WRITTEN CONTRACT BETWEEN SELLER AND PURCHASER, THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

IMPORTANT NOTICE

THIS SHIPMENT HAS BEEN CAREFULLY INSPECTED AND PROPERLY PACKAGED BEFORE LEAVING THE FACTORY. WE CANNOT ASSUME RESPONSIBILITY FOR BREAKAGE THAT MAY OCCUR DURING TRANSPORTATION OF THE GAME. IF THIS GAME IS DAMAGED UPON RECEIPT FROM THE CARRIER, IMMEDIATELY NOTIFY THE CARRIER AND FILE A DAMAGE REPORT.

mvation, not to be disclosed oF copied without the express permission of CAPCOM COIN-OP, INC

Page 5

CAPCOM” co-op, ine. MARVEL VS. CAPCOM ™

KIT INSPECTION

There are two kits available for conversion to MARVEL VS. CAPCOM ™:

  • MVC1000 (“FULL” kit) contains the 2) MVC 1000B (“B” kit) contains the game complete game cartridges, all necessary graphics, software cartridge (B-cartridge) and must also be and replacement joysticks and button switches. installed to a current CAPCOM® System II game. The “FULL” kit is intended for conversion of most It includes all the necessary game graphics for a JAMMA-compatible, horizontal screen cabinets. cabinet conversion (marquee, control panel overlay, monitor card, etc.).

Check that all parts have been shipped with your kit. If any parts are missing, contact your distributor immediately.

KIT PARTS LIST

MVC1000 | MVC1000B PART NO. DESCRIPTION MVC1400 CPS II System Cartridges (A/B ) MVC1400B CPS II System Cartridge (B ) GE1200 Monitor Card AW00270 Marquee AW00216 Overlay, Control Panel AW00245-2 Decal, Joystick & Button Switches AW00271 Decal - Top, _ Instruction AW00272 Decal - Bottom., Instr tion PM00206 Manual, Operators AW00147 Decal, Cabinet Side GE2030 Joystick, 8-way 6-0130 Switch, 1-Player Start Button (White) 6-0131 Switch, 2-Player Start Button (White) 6-00133 Switch, Button (Red) 16-00134 Switch, Button (Blue) 6-00136 Switch, Button (Green) 03-0052 Cable, Auxiliary Volume/Test 3-0066 Bracket, A-Cartridge Mounting <2 2[2}e)e}e}e]e) 4 2/2) 2}e2]e]e)e}e}e/e}e)elefe)ese Alo/alalal]oa}a}rofr]s}a}|a}a}a)]a}a)]a}a

Proprietary and n of CAPCOM COIN-OP, ING I

Page 6

® @AP@OM" coin-op, INC. MARVEL VS. CAPCOM ™

CAUTION 4

Please read the following instructions to keep the PC board in good condition:

#Do not block the ventilation slots.

@Do not drop or bump the board.

Do not spill any liquids on the case.

@Do not disassemble the case.

ATTENTION

@ yy The product that you have purchased contains a recyclable

battery. At the end of its useful life, under various state and local laws, it may be illegal to dispose of this battery into the municipal

a? waste system. Check with your local solid waste official for

details in your area for recycling options or proper disposal.

DISASSEMBLING THE CASE OR REMOVING THE STICKER MAY CAUSE THE TERMINATION OF YOUR REPAIR WARRANTY

OF YOUR REPAIR WARRANTY.

Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP,

Page 7

CAPCOM" COIN-OP, INC. MARVEL VS. CAPCOM ™

KIT INSTALLATION

MAKE SURE ELECTRICAL POWER TO THE GAME ISOFF BEFORE STARTING THE KIT INSTALLATION.

PREPARATION

  • Disconnect and remove the old printed circuit board(s) from the cabinet.
  • Remove or open the control panel, and disconnect and remove the buttons and joystick(s) from the control panel.
  • Remove any covering from the control panel overlay, and then remove the control panel overlay.
  • Place the drill hole template over the control panel to determine where any new holes should go. Center punch any needed new holes on the control panel.
  • Cut out the new holes using a 1-3/16" hole saw.
  • If there is an additional control panel cover, figure 1 (such as plastic or lexan) that will be utilized, cut any additional holes using the same template. *cover is not included in the kit.
  • Plug up unused holes with a wood dowel diameter) and sand any rough edges.

INSTALLATION (-1/8"

Marquee Installation

  • Remove the marquee plexi glass, marquee overlay, and the cabinet graphics.
  • — Install the new marquee and replace the plexi glass. Clear plexi glass is included in “full” kit.

Control Panel Overlay Installation (See Figure 1)

  • The control panel overlay in the kit is oversized to accommodate most control panel sizes. Center the overlay on the control panel, leaving some excess material at the edges.
  • Remove the protective backing from the overlay and press it down on the control panel, keeping it properly aligned. Press it down firmly, smooth out any bubbles, and press it over the edges.
  • Trim any excess from the overlay. Place the drill hole template on top of _ the overlay, aligning it with the joystick holes. Pierce through the overlay at each control panel hole. Then, cut away overlay material covering the joystick and button holes. Remove the template and clean off the overlay.
  • Peel off the backings of the 6-button and joystick decals, align over the control panel holes, and press in place on the overlay (refer to the drill hole template for proper placement). Using a knife, trim material from the center hole of the joystick decal.
  • Install the control panel cover, figure. 1. (if required).

Overlay (Trim to size)

Control Panel

Figure 1: Overlay Installation

CABINET DECAL INSTALLATION

  • Remove monitor glass and install monitor card
  • Peel-off the backing to the instruction decals and place on both the top and bottom of the monitor card. (See Figure 5). Also, apply the cabinet decals to both sides of the cabinet.

MARQUEE OVERLAY

MONITOR CARD CABINET

DECAL

INSTRUCTION DECAL - BOTTOM

| INSTRUCTION DECAL - TOP

Figure 5: Cabinet Decal Installation

we

Page 8

® CAPCOM" com-op, INC.

Re-assembly of Components

  • Notice that there are two white buttons. See figure 2. The WHITE buttons are START buttons. Install the PLAYER ONE button on the top left-hand side of the control panel, and the player two button on the top right-side of the control panel. 1 Player 7 BPhayer Q © id ia vm Figure 2: Start Buttons Red Green Blue Red Green Blue wey TS

Red Green Blue Red Green Blue

Buttons

Retaining GS

Switches —— cF ‘ve0%00 Figure 3: Control Panel Buttons and Switches

  • Install all buttons and retaining rings on the control panel as shown in Figure 3. Install two red buttons to the immediate right of each joystick, install two green buttons to the right of the red ones, and install two blue buttons to the right of the green ones.
  • Install the switches on the buttons as shown in figure 3. Orient the switches so that when a button is pressed, the plastic contact on the switch is depressed.
  • Install the joysticks on the control panel as shown in figure 4.

Figure 4: Joystick Installation

CONTROL PANEL WIRING

Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, MARVEL VS. CAPCOM ™

NOTE: all switch wires used in this game must be wired to the normally-open connection on the switches. Each switch requires a ground wire on the common connector and the appropriate control or switch wire on the normally-open connector of the switch.
  • Reconnect the existing jamma connectors to the control panel according to the chart in table 1.
  • Connect the player | and the player 2 kick buttons to the auxiliary cable harness as shown in figure 6. Make the connections according to the chart in table 2.

To A-Cartridge

‘To Control Panel Bution Switches (Not Used)

To Volume / Test ‘Switch Bracket vane Figure 6: Auxiliary Cable Harness

TEST SWITCH WIRING

  • Your cabinet may already equipped test switch. An optional test/volume bracket (see Figure 7) is available through your local CAPCOM distributor (part number 03- 0050). When installing, the test switch bracket should be mounted inside the coin door and on top of the cash box for easy access. (See Page 7 for wiring detail)
NOTE: only the test switch is used for this game; the volume up/down switches are disabled. Volume adjustments must be made through the volume control knob located on the PC board.

Figure 7: Test/Volume Bracket

  • If you are converting a cabinet that is equipped with CAPCOM® Q-SOUND, you may use stereo audio output connect to existing Q-SOUND POWER AMPLIFIER.
Page 9

@ CAPECN” coin-op, inc. MARVEL VS. CAPCOM ™

AN CAUTION

IMPROPER INSTALLATION OF THE JAMMA HARNESS TO THE GAME CARTRIDGE WILL CAUSE DAMAGE TO THE ENCLOSED PCB.

GAME CARTRIDGE INSTALLATION

“FULL” KIT

  • Install the four (4) mounting brackets to the underside of the “A” cartridge as shown in Figure 10.

Figure 10: Mounting Bracket Installation

“FULL” KIT

  • Using the supplied wood screws, fasten the game cartridge case to the control panel shelf, as shown in Figure 11.

Figure 11: Case Mounting

  • Connect the JAMMA harness connector and the auxiliary cable connector to the “A’ cartridge. If your cabinet is equipped with Q-SOUND, also attach the audio cables.

Proprietary and confidential information, not to be disclosed or copied /N\ WARNING

DISASSEMBLY OF EITHER GAME CARTRIDGE WILL VOID YOUR WARRANTY.

“B” KIT

  • To remove the existing “B” cartridge from the “A” cartridge, pull the old case clamps apart (see Figure 12). Carefully remove the old “B” cartridge and install the new “B’ cartridge. Re-install the case clamps.

ase Clamp

"A" Cartridge Figure 12 : Case Clamp Installation

  • Power-up the game and set all operator adjustable options by pressing the TEST switch. Follow the instructions under the TEST MENU section of this manual.

ission of CAPCOM® COIN-OP, ING. 5

Page 10

° @APRCON" coin-op, INC MARVEL VS. CAPCOM ™

TEST MENU

The test menu allows you to test the functions and configure the game. These items include input devices such as joysticks, buttons and coin door or switches, output devices such as monitor, speakers and meters. Through the Test Menu you can also access the Configuration Menu, where you can change the settings of the game.

TEST MENU 1. ACCESSING THE TEST MENU . For a CAPCOM® cabinet, or a cabinet with

1.INPUTa test switch:
2.OUTPUTMake sure the game is on and push the test switch.

The screen shown left will appear.

3.SOUND & VOICE.For a cabinet without a test switch:

4. COLOR Push the blue test switch on the outside of the black

plastic casing.

5.DOT CROSS HATCHRefer to the inside back cover of the manual.
6GAME DATA2.HOWTO SELECT AN ITEM
7.CONFIGURATION.Use the PLAYER I JOYSTICK to move the
8.MEMORY CHECKarrow in front of the desired item and press the

PLAYER I SHOT | button, as shown below in various

9.EXITcontrol panel configurations:
SELECT = 1P UP or DOWN3.CLOSING THE TEST MENU
START=1P SHOT1To close the Test Menu, highlight “9, EXIT”

and push the PLAYER I SHOT J button.

Player 1 Joystick Player 1 Start

. To return to the test menu, push the PLAYER | START and PLAYER I SHOT J buttons simultaneously. C y) . The test menu will always return to the screen:

A__\\_GAASOSS-a)After you exit the “7. CONFIGURATION

Player 1 Shot 1 Player 1 Shot 2 sat MENU” and

  • After the memory is tested from the menu, “8, MEMORY CHECK”.
  • TEST MENU ITEM DESCRIPTIONS

INPUT Used to test all the input switches, such as joysticks and buttons. The “0” changes toa “1” as the button is pushed or joystick is moved. Check connections and switches in case the “0” doesn’t change to a “1” when depressed or moved. OUTPUT Used to test the coin meter and the coin lock. SOUND & VOICE Select a code of SOUND or VOICE with the PLAYER I JOYSTICK. Push the PLAYER I SHOT | _ button to hear the sound of the selected code. COLOR Shows color bars of red, green, blue, and white. Adjust RGB and brightness to obtain the optimum color balance and solid black background. DOT CROSS HATCH | Used to test the screen size, focus and distortion. GAME DATA Coin meter and Free play information will be displayed. CONFIGURATION Used to change the game play settings. Refer to the CONFIGURATION MENU section. MEMORY CHECK Used to test memory. “OK” appears when each block of memory passes test, “NG” appears in case of malfunction. If “NG” appears, repeat the memory test and wait for the “OK” message. Contact your distributor if “NG” still appears. EXIT Select this item and push the PLAYER 1 SHOT 1 button to return to game play mode.

6 Proprietary and confidential information, not tobe disclosed or copied without the express permision of CAPCOM® COIN-OP,

Page 11

CAPCOM" coin-op, Inc. MARVEL VS. CAPCOM ™

CONFIGURATION MENU

The Configuration Menu is used to change various game settings such as level difficulty, credits, sound configuration, etc. These settings are stored in memory on the PCB.

The Configuration Menu is divided into 2 sections. In the SYSTEM section, you can change credits, sound, and coin door configurations. In the GAME section, you can change the play difficulty level and duration of the game.

  • ACCESSING THE CONFIGURATION MENU
  • CONFIGURATION MENU + From the TEST MENU, move the arrow to
>1.SYSTEM“7, CONFIGURATION” and push the

PLAYER 1 SHOT 1 button.

2.GAMEThe screen left will be displayed.

A description of each option is

3.DEFAULTexplained in the table below.
  • SAVE & EXIT

SELECT 1P UP OR DOWN START 41P SHOT1

  • CONFIGURATION MENU ITEM DESCRIPTIONS

SYSTEM Select this item to change settings for credits, monitor flip, sound and coin door configurations. GAME Select this item to change difficulty level, damage level, time count speed, maximum number of rounds and event type. DEFAULT | Use this item to restore configuration settings to the original factory values. Press the PLAYER / SHOT 1 and PLAYER I SHOT 2 buttons at the same time to restore default values. SAVE & Use this to save new configuration settings and exit to the Test Menu. The message “SAVING EXIT NEW CONFIGURATION IN EE-PROM” will appear while the new settings are being saved. DO NOT turn power off to the game until “SAVING” is complete and the Test Menu reappears.

Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN.

Page 12

® CAPCOM co-op, Inc. MARVEL VS. CAPCOM ™

SYSTEM CONFIGURATION

CHANGING THE SYSTEM 7-1, SYSTEM CONFIGURATION CONFIGURATION SETTINGS

COIN MODE2COIN1CREDITMove the PLAYER I JOYSTICK up or down to

highlight the desired option. Once the option is

CONTINUEONhighlighted, move the PLAYER I JOYSTICK _ left or
MONITORNORMALright or press the PLAYER 1 SHOT J button to select.

DEMO SOUND ON

SOUND MODE STEREO (Q SOUND)

CHUTE TYPE 2 CHUTES SINGLE

REGULATION ON

  • EXIT

SELECT OPTION =1P UP OR DOWN MODIFY SETTING = 1P LEFT OR RIGHT 1P SHOT1 OR SHO’

SYSTEM CONFIGURATION ITEM DESCRIPTIONS

  • COIN MODE SELECT THE CHARGE PER PLAY.
  • CONTINUE SELECT ON FOR CONTINUOUS PLAY OR OFF FOR NON-CONTINUOUS PLAY
  • MONITOR FLIPS THE POSITION OF THE SCREEN. IF THE SCREEN APPEARS UPSIDE-DOWN, CHANGE THE SETTING TO FLIP; IF THE SCREEN APPEARS CORRECT, SELECT NORMAL.
  • DEMO SOUND | TURNS ATTRACT SOUNDS ON OR OFF.
  • SOUND SELECT STEREO OR MONAURAL FOR USE WITH YOUR CABINET. NOTE: STEREO SHOULD MODE ONLY BE SELECTED FOR USE WITH CAPCOM® QSOUND CABINETS.
  • CHUTE TYPE SELECT THE NUMBER OF PLAYER(S) AND COIN CHUTE TYPE.
  • REGULATION | If set to “ON” the color of the blood changes from red to white.
  • EXIT TO SAVE THE SETTINGS AND RETURN TO THE CONFIGURATION MENU, HIGHLIGHT THIS ITEM AND PUSH EITHER THE PLAYER | SHOT 1 BUTTON OR THE PLAYER ] SHOT 2. BUTTON.

SYSTEM CONFIGURATION OPTION SETTINGS

1. COIN MODE1 COIN1 COIN1 COIN1 COIN1 COIN
| CREDIT.2 CREDITS3 CREDITS4 CREDITS5 CREDITS
1 COIN1 COIN1 COIN1 COIN2 COINS
6 CREDITS7 CREDITS8 CREDITS9 CREDITS1 CREDIT
3 COINS4 COINS5 COINS6 COINS7 COINS
1 CREDIT1 CREDIT1 CREDIT1 CREDIT1 CREDIT

8 COINS 9 COINS 2 COINS START FREE PLAY 1 CREDIT 1 CREDIT 1 COIN CONTINUE

2. CONTINUEONOFF
  • MONITOR NORMAL FLIP
4. DEMO SOUNDONOFF
  • SOUND MODE STEREO (Q SOUND) MONAURAL
6. CHUTE TYPE2 CHUTES SINGLE2 CHUTES MULTI1 CHUTE SINGLE
  • REGURATION ON FACTORY SETTING

Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP,

Page 13

CAPCOM" coin-op, INC. MARVEL VS. CAPCOM ™

GAME CONFIGURATION

7-2. GAME CONFIGURATION CHANGING THE GAME CONFIGURATION SETTINGS

DIFFICULTY NORMAL

DAMAGE LEVELNORMALMove the PLAYER I JOYSTICK up or down to
TIMER SPEEDNORMALhighlight the desired option.Once the option is

highlighted, move the PLAYER I JOYSTICK _ left or

MODE SELECTFREE SELECTright or press the PLAYER I SHOT J button to select.

JOIN-IN ON

EVENT OFF

GAME SPEED FREE SELECT

  • EXIT

SELECT OPTION P UP OR DOWN MODIFY SETTINGS 1P LEFT OR RIGHT 1P SHOT1 OR SHO

ITEM DESCRIPTION OPTION SETTINGS

1. DIFFICULTY | SETS THE GAME DIFFICULTYLEVELEASYNORMALHARD |HARD 2
HARD 4HARD 5EXPERT
2. DAMAGESETS THE OFFENSIVE POWER LEVEL.LOWNORM.HIGHMAXIMUM

LEVEL

3. TIMERSETS THE SPEED OF COUNTDOWN FROM THE TIMERSLOWNORMALFAST,FASTEST

SPEED DISPLAY.

  • MODE USED TO TURN THE “EASY MODE™ ON AND OFF. FREE SELECT EASY MODE SELECT Ser To" “FREE SELECT” ALLOWS THE PLAYER TO. 7 NORMAL OR EASY MODE.
THE OPTION TO ALLOW OTHER PLAYERS TO.T LIFE2 LIVES4 LIVES

JOIN-IN

  • EVENT SPECIAL SETTING FOR TOURNAMENT EVENT. OFF 1 MATCH: ONLY ONE CREDIT IS REQUIRED FOR A 2P GAME. THE GAME ENDS AFTER ONE MATCH REGARDLESS OF THE RESULT.
  • JOIN-IN
4. GAMESET THE GAME SPEED. “TURBO I” AND “TURBO 2”NORMALTURBO |TURBO 2

SPEED ALLOWS THE OPERATOR TO SET THE GAME SPEED. “FREE SELECT” ALLOW THE PLAYER SELECT THE GAME SPEED.

  • EXIT RETURN TO THE CONFIGURATION MENU.
NOTE: ZX@

Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM COIN-OP, INC 9

Page 14

CAPCOM’ coin-op, INC. MARVEL VS. CAPCOM ™

JAMMA Connections

SOLDER SIDE COMPONENT SIDE

WIRE COLOR CONNECTOR ODD ROW GND GND +5 VDC +5 VDC N.C. +12 VDC KEY NIC COIN LOCK 2 ¥SPEAKER _() N.C. VIDEO GREEN VIDEO SYNC SERVICE (FREE CREDIT) NIC 2 PLAYER - COIN 2 PLAYER - START 2 PLAYER - UP 2 PLAYER

  • DOWN 2 PLAYER
  • LEFT 2 PLAYER
  • RIGHT 2 PLAYER
  • LIGHT PUNCH 2 PLAYER
  • MEDIUM PUNCH 2 PLAYER
  • HEAVY PUNCH

NIC NIC GND GND

NIC NC NIC NIC PURPLE/YELLOW PLAYER 2 HEAVY KICK NIC NIC PINK PLAYER | HEAVY KICK RED PLAYER | MEDIUM KICK BLUE PLAYER | LIGHT KICK GRAY/YELLOW, PLAYER 2 LIGHT KICK PINK/YELLOW. PLAYER 2 MEDIUM KICK NIC NIC GRAY/YELLOW TEST BRKT-VOLUME UP BLACKMWHITE TEST BRKT-VOLUME COMMON BLACK PLAYER 2 KICK - COMMON BARVAZZCA-IAMIGATyS nee Ke

moaccmeNn<txe

wusryprnny ERSSaR GND GND +5 VDC +5 VDC NG. +12 VDC KEY. COIN COUNTER 1 COINLOCK1 ¥*SPEAKER __() NC VIDEO RED VIDEO BLUE VIDEO GROUND DIAGNOSTICS T PLAYER _- COIN TPLAYER _- START. T PLAYER _- UP TPLAYER _- DOWN TPLAYER _-LEFT TPLAYER _- RIGHT TPLAYER _- LIGHT PUNCH 1 PLAYER - MEDIUM PUNCH T PLAYER _- HEAVY PUNCH NIC NIC GND GND

CONNECTOR EVEN ROW WIRE COLOR

NIC NIC NIC NIC NIC NIC NIC NIC NIC

NIC NIC NIC NIC NIC TEST BRKT-VOLUME DOWN PINK/YELLOW NIC PLAYER 1 KICK-COMMON BLACK

Proprietary and confidential information, not (0 be disclosed or copied without the express permission of CAPCOM® COIN-OP,

Page 15

® @APCOM” co-op, inc. MARVEL VS. CAPCOM ™

REFERENCE INFORMATION

GAME CASE CONTROLS

REGISTER

(NOT USED) ( ) OUT IN

*VOLUME UP

*VOLUME DOWN

JAMMA AUXILIARY CABLE AUDIO OUT (FOR Q SOUND) CONNECTOR CONNECTOR RIGHT: RED, LEFT: WHITE 300800

TYPICAL CONTROL PANEL LAYOUTS FOR “MARVEL VS. CAPCOM ™

\v1600200

Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC

Page 16

NOTICE

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense.

WARNING

Federal law provides severe civil and criminal penalties for the unauthorized reproduction, distribution, or exhibition of copyrighted audiovisual works and video games.

The Federal Bureau of Investigation investigates allegations of criminal copyright infringement.

CAPCOM” COIN-OP, INC. 475 Oakmead Parkway Sunnyvale, CA 94086 Phone: (408) 774-0500 Fax: (408) 522-5331

Copyright © 1997 CAPCOM © coin-op, INC., All Rights Reserved