CATHODE RAY TOMES

Air Combat 22 kit

Air Combat 22 (Japan, ACS1 Ver.B) (Namco, 1995) · Kit Manual · 13 pages · 20 sections · original scan

Page 1

namco Upgrade Kit Manual Air Combat 22 io i 1.0 Specifications

Ll Conversion Game Specifications

Power Supply: Switching Power Supply, 200 Watts

Power Consumption: 600 Watts

Monitor: One (1) 46” Rear Projection Color Monitor

Kit Specifications:

PCB Kit | Namco Super System 22 PCBs

Harness

Decals, Signs, Labels

The Air Combat SS22 upgrade kit consists of the Air Combat SS22 PCB kit, a new wire harness and assorted decals/signs/labels. The kit can be installed in the original Air Combat cabinet.

Page 2

2.0

3.0

3.1

3.2 namco Upgrade Kit Manual Air Combat 22

INTRODUCTION

This manual provides installation instructions for Air Combat S$S22 kits. Inspect the kit contents, compare against the (included) parts list and notify the distributor about any damaged/missing parts.

INSTALLATION

Precaution3

Before replacing any parts, turn the AC power OFF and unplug the game.

The game power supply includes areas of HIGH VOLTAGE. Take care at all times to avoid electrical shock when working on the game.

Game _ Installation

Verify power has been removed from game.

Unlock access door on RHS and remove game chassis.

Disconnect AMP connector and Ground strap from game chassis.

Rather than separating remaining connectors of harness all at once, it would be to your advantage to do them one at a time, replacing the “old” with the “new” as you go.

Mount Audio Amp board to Super System 22 chassis using the 3 screws provided. Refer to Card Cage Super System 22 Assembly drawing for correct position.

Using AC22 Overall Layout drawing, connect the new cable harness to SS22 Mother PCB and Audio Amp connectors. The new cable harness connectors are labeled to match the board connectors they connect with.

Remove the old chassis from the mounting board and place the new SS22 chassis in its place. Position the new chassis so that a side with the ventilation holes faces the fans mounted inside the cabinet. This will help to promote air flow through the chassis. Secure the chassis to one of the mounting holes using an existing screw. Drill new holes for additional mounts if desired.

Attach Ground strap to new chassis.

Remove cables @ JO1,J202 & J203 from 2 Ch AmpPCBs.

Page 3

namco Upgrade Kit Manual Air Combat 22

10.

19.

20.

21. Match the new harness connectors labeled J202 & J203 with the connectors on either 2 Ch Amp board and verify they mate properly (molex or mate-n-lock). A converter cable is included in the harness for the power lines connecting to J20 1. If the harness connector labeled J201 matches the board connector J201, connect them. If the connectors differ, you'll find the proper connector about 5” back on the orange and black power leads. Remove the (now unnecessary) orange-black converter-cable and connect the connector at J201 .

Referring to the AC22 Overall Layout drawing, separate the 12-pos connectors (on the original cable) coming from beneath the seat assy and connect (from the new harness) the 12-pos connector labeled ‘20’.

Separate the other 12-pos connectors (on the original cable, coming from the CRT) and connect the new 12-pos connector labeled ‘25’.

Separate the 15-pos connectors (the ones with 11 -wires) and connect the 15-pos connector labeled ‘24’.

Separate the other 15-pos connectors (the ones with 14-wires) and connect the 15pos connector labeled ‘ 17’. For more exact ID, both the connector you are replacing and the new one are unique in that they have 2 orange wires going into the same pin-hole.

Separate the 9-pos connectors and connect the (unlabelled) 9-pos connector.

Separate the 6-pos connectors and connect the 6-pos connector labeled ' 16’.

You should now have totally replaced the original harness with the new harness. Verify there are no open/unused connectors on the new harness.

Cut the cable ties fastening the original harness to mounting board and remove.

Verify all connectors are joined and that cable/harness routing isn’t restricted by chassis edges, etc.

With SS22 chassis mounted and cabling complete, slide mounting board into cabinet and re-verify proper positioning of chassis (ventilation holes) in front of* fans. Forced-air flow (whether the fans are cabinet-mounted or chassis-mounted) is necessary for proper game operation.

Position Card Cage Shield over card cage, aligning mounting holes with |/ 4-20 bolts coming from ceiling of cabinet (beneath joystick). Either remove the nuts and fasten the shield in place (using the same nuts) OR simply guide the shield onto the bolts and fasten in place with additional 1/4-20 bolts.

<

Page 4

b/d

e a

6) namco Upgrade Kit Manual Air Combat 22

3.3 Cabinet Graphics

Install the cabinet graphics provided. Float the graphics on by applying a spray of ammonia cleaner to each surface. Smooth out the bubbles and liquid with a paint squeegee. Wipe the decal dry with a soft cloth.

Install the marquee overlay and panel in place of the existing marquee.

Install the game play instructions provided with the kit on top of the marquee.

For help in correctly positioning decals, etc., refer to Air Combat 22 flier.

Set Up and Test

Refer to sections 5 & 6 in the Air Combat Operators manual for Adjustments and How to Play instructions. Be sure to check the factory game and coin settings.

Page 5

1 9 Upgrade Kit Manual namco Air Combat 22

4.0 PARTS LIST

[___| NAMCO PINDescriptionQty[UM |
A205-03684-00PCB Kit, Air Combat SS221ea
A210-03593-00Shield, Card Cageea
A210-04089-00Sign Bracketea
A240-03540-00decal, bottom, rear panel1ea
A240-03853-00decal, side panel, cockpit, rightea
A240-03855-00decal, side panel, cockpit, leftea
A240-04013-00decal, marquee acry, sc, w/50” mon1ea
A240-04037-00decal, mon, side cabinet, top leftea
A240-04037-01decal, mon, side cabinet, top rightea
A240-04038-00decal, mon, side cabinet, center2ea
A240-04039-00decal, mon, side cabinet, bottom2ea
A240-04044-00decal, side panel, bottom st, rt PCB door1ea
A240-04045-00decal, bottom side panel, left frontea
A240-04045-01decal, bottom side panel, left back1ea
A240-04045-02decal, bottom side panel, right w/cash box1ea
A240-04045-03decal, bottom side panel, right w/PCB doorea
NOTE: comes with A240-04044-00
A240-04054-00decal, Eagle Squad 2, View Chg 11ea
A240-04056-00Sign, Instructionea
A245-04493-00Manual, Instructions1ea

A250-03996-00 | cable [ea

A250-03997-00cable| ea
A250-04015-00cable\ea
A250-04016-00cable1ea
A295-04475-00Acrylic, Marquee Cover, kit1ea
Page 6

Card Cage Super System 22 Assembly

WARNING: DO NOT separate board set.

CPU (A) P2 PCB Assemoty

® Digital Signal Processing (OSP) PCB Assemmo1y

  • M-ROM PCS Assematy

4a) Video PCB Assematy

Ribbon Cante 2 otaces)

  • tom DSP 203 0 Fiasn ROM a4 lr om) M-RCM JA to Viaeo V3 2 (40)

®)

“dosrer °¢3 Asserey

MPM (F) PCS Assemoiy

SPM (E>) PCB Assemoty

: The side and too oaneis are snown removed trom the card cage. for clanty i ONLY. Also, :ne coaras aye are snown iransoarent ‘ order to snow tne connectors in tne cack. ’ Auaio AMP (4) PCS,

Page 7

NO! 1 AW wir

  • Coble te each group every 8° 3 Legily wentity connector with correct de siya tor, ent marker

using p TO POWER PCB

CN-Jh PLUU, UNIVERSAL MATE-N-LOK AMP # 1-480706-0 CONTACT # 350570-1 ore 18 amy, 1WU7 style; unless spec.tied, IM PCB (COIN DOOR) 35.0 WHT/BRN (2? AWG) » cN-J1 CONTACT # REMSION DESCRIPTION bale APPROVAL PROO. RELEASE 7/7/95

PLUG, MINI MATE-N-LOK AMP # 1721661 170362-1 FROM POWER SUPPLY PLUG, 0.093 STANDARD MOLEX # 03-09-2092 CONTACT # 02-09-2116

35.0 Pi (22 AWG) TO SERVICE PANEL

CN-I3 PLUG, MINT MATE-N-LOK AMP w 172169-1 35.0 GRY

CONTACT # 170362-1 22 aug 35.0 BLK? awG) 39.0 WHI/BLK

lols ofoln alo) 35.0 Vv. 122 awG> CN-17 RECEPTACLE, 0.093 STANDARD MOLEX # 03-09-1157 CONTACT # -2-09-1117

EReRPRR TS [IN MECH CN-16 RECEPTACLE, 0.093 STANDARD MOLEX 03-09-1064 CONTACT # -2-09-1117

WSS) Seals oho) TO AUDIO AMPL. fi] cN-201 PLUG, UNIVERSAL MATE-N-LOK AMP # 1-480700-0 CONTACT # 350570-1 Hamco 150 Chercot Avenue Son Jose, CA 95131

[tumeey SC*&@ poms) ane HARNESS, KIT MAIN 2

= CHE weneo 7/7/95 ‘onen na _ pep gg, mars [SRE mee ae Bos C |A250-03997-00 LA | BO _NOT SCALE [an le

Page 8

1 AU mes ore G2 owy, 1UU7 style Z.Luble tie euch group every 8" 3 Leyisly wentiFy connector with correct rker dysignu tor, us wnent From Main Peb (GU)

  • BEB |__ 30.0 GRU.

f

CN Jd PLUG, MIND MATE -N-LOK REVISION

REV DESCRIPTION. DATE APPROVAL PROD. RELEASE 7/7/95 REVISE CN-J203, .J4 7/17/95 TN

To Front Spk & RGB

AMP #1721681 30.0 Blu CN-25

INTACT # 1/0502 30.0 BRN {300 BLK RECEPTACLE, 093 STANDARD MOLEX # 03-U9-11z6

Filmi sof} From Audio Pcb (JPN

CN-J2 Ver.) 32.0 GRA CONTACT # -2-09-1n7

PLUG, MINI MATE-N-LOK 32.0 ORG. 32.0_YEL

AMP # 172167-1 CONTACT # 170362-1 32.0 PINK

ll Seat Assy.

32.0 GRN 32.0 ORG 320 YEU CN-20

32.0 PINK RECEPTACLE, 0.093 STANDARD

HOUSING, EI

From Mein PCB cN-J7 PLUG, AMP ®

CN=J8 PLUG, MIN] MATE-N-LOK AMF @ 17217i-1 CONTACT # 170362~1 From audio Feb CN-J4

BIVST Slo folr pol] s[ojcul CN-J203 (Audio pcb) AMP 4 171822-4 CONTACT # 170262-1 CONTACT ® 170362-1 HOUSING, EI SERIES 2 AMPH 171822-2 iLO RED/BLK MOLEX W03-09-11cE

SERIES 1.0 BLK CONTACT W 02-09-1117

Teale] From Main PCB (Controller & Throttle) |}. io HT 51.2. SLO HT/RED HIZBLK

MINI MATE-N-LOK 1721701 PRICIR Gs Be wlofNjo[alS[q[Y-ujo +] ° CMP EMMIS ola} To Controller & Start bin

=]

3.0 WHIZYEL CN-24

3210 WHI/ORG. RECEPTACLE, 0.093 STANDARD

310 WHI/VID MOLEX #03~09-1157

luff =} 1 CONTACT # 1702621 CONTACT # 02-09-1117

=] Jeo)

a m Main PCB (Gun) [ps4 wuisory _

24.0. WHIZ BRN HLZGRY.

  • HIZBRN ns

CN=S4 arr HMIZGRN, ~. — (HI/GRN.

HOUSING, E1 SERIES 24.0 BLK _ BLK S

AMP # 171Bee~8 340 vid “10. Oo

af CONTACT # 17uebe=1 caves ov 150 Ch San jose, CA 95131 HARNESS, KIT MAIN I

eR ne erry T7795 SERRE PORE xx £ 90h mocurs ay Spe [oman no ee ies £0005. C | A250--03996-00

Wst0 Ov a BO NOT SCALE [ar iat

Page 9

NOT 1 Al wires cre c& ung. 1007 style

2 Leble tie €6 REVSION

REV

1 group every 8

Bo Legily enlify © Ld od

DESCRIPTION

Dale APPROVAL

7/7/95 8/7 “95

ale gayi tur. | PRODUC TION RELEASE Le REVISED P/N ON J6

From Main Pcb

CN-J6

HOUSING, El SERIES

AHP W 1-171622-2 CONTACT & cCN-J3.

HOUSING, £1 SERIES

AMP # 171822-8 CONTACT # 170263-1

To Audio peb CN~J202 HOUSING, EI SERIES AMP @ 171822-5 CONTACT # 170263-1 haliaGo 150 Charcot Avenve Son ose, CA 9513

[GRaw BY poser) mie

HARNESS, KIT

onreatD Sit [oRamic nO | HEE BTC ["A250-04015-00 |B

Page 10

NOTES!

1 AW mres Gre 16 owg. 1007 style 2 uble te each group every 6. Bo Lagily identity connector wi desyne tor, using permanent carker correct

HOUSING, 2139 SERIES

MOLEX # 09-50-7031 CONTACT # 08-50-0105 (Chain> OR # 08-50-0106 (Louse? ») REMSION \

REV OL SCRIPTION

J PROD. RELEASE +

Dale 7/795 APPROVAL

CAP, UNIVERSAL MATE-N-LOK

AMP & 1-480701-0 CONTACT # 350561-1 180 Chorcut Avenue Son_Jose, CA 95131

kaw BY pore) aia HARNESS, KIT

wos 2 ‘Bie Cc

OO NOT SCALE

A

Page 11

REMSION —~/

LA mes ure eé awg. 1007 style DESCRIPTION

DATE APPROVAL

2 Cuble tie euch group every BF 3 Legily identify connecter

PREL. RELEASE

with correct 7/7/95

wrher From Mait Zz a

s To Audio Pcb ‘CN-LINK

CN=12

HOUSING EL SERIES

AMP WH 171822-9 CUNTACT # 17U263-1 RECEPTACLE, G93 STANDARD MOLEX & 03-09-1052 CONTACT 4 02-09-1117

HARNESS, KIT

MAIN 5

rg rr tev

  • A250- 1 T SCALE Tout at
Page 12

®)

@

ez cs} z

50” PROJECTION TV

2 OUTLET RECEPTACLE

Baas (90~61150-052¥

SLLVM O02 ATddNS YWAMOd cI PesoRr RO oo ry

From 2—Channel audio pcb (2PLS) 36” FLORESCENT

RGB/NTSC pcb

ATTRACTION BOX

18” FLORESCENT

COCKPIT DISPLAY

Located on pcb cage

Page 13

w JS

sa Matz a Pe reset 4260-09780-00 7 ZZ-W3LSAS Y3dNS Bod NIVN I3 nde oat ew 24 ve ‘S~VHS| @) _—_ !

i = | nea ap 4230-09708-00 nn pee me so-cares-o1 |

4280-09001-00 I

AIR COMBAT’ 22 I

OVERALL WIRING DIAGRAM (2/2) + Date 7/25/95 _ Rev A _ _