CATHODE RAY TOMES

Dynasty Wars

Dynasty Wars (USA, B-Board 89624B-?) (Capcom, 1989) · Manual · 20 pages · 20 sections · original scan

Page 1

TWANVIN NOILONYLSNI LD

Page 2
WARNING

THIS GAME MUST BE GROUNDED. FAILURE TO DO SO MAY RESULT IN DESTRUCTION TO ELECTRONIC COMPONENTS.

WARNING: This equipment generates, uses and can radiate radio frequency energy and if not used in accordance with the instruction manual, may cause interference to radio communications. It has been tested and found to comply with the limits for a CLASS A computing device pursuant to SUBPART J and PART 15 of FCC RULES, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area is likely to cause interference in which case the user at his own expense will be required to take whatever measures may be required to correct the interference.

CAPCOM, USA INC.

INVITES YOU TO USE

OUR SERVICE NUMBER FOR SERVICE INFORMATION CONCERNING THIS GAME, OR ANY OTHER CAPCOM GAME YOU NOW HAVE ON LOCATION. PLEASE HAVE GAME SERIAL NUMBERS AND CABINET NUMBERS READY.

CALL US FOR PROMPT, COURTEOUS

ANSWERS TO YOUR PROBLEMS.

Direct Number (408) 727-0400

Page 3

Before You Get Started...Stop!

Does your new game package include all listed parts? (Is it complete?)

. Is the game you have chosen to transform able to supply all the required voltages for the new game?

Note: Some games, (i.e. Ms. Pac Man, Galaxian, etc.) regulate their voltages on the main PC.B. This makes the existing power supply inefficient. These games will require a change in power supply for your new game. Many game supply houses can offer you a switching regulated power supply for a relatively low cost.

Is the monitor configuration compatible? In most games it is rather difficult to change the monitor from a vertical mount to a horizontal mount. We recommend you choose a game cabinet with the same mount as your new game requires.

. Do you have the necessary tools? (See the recommended tool list)

Page 4

WARRANTY, REPAIR AND RETURN POLICY

REPLACEMENT PARTS: CAPCOM USA maintains a stock of replacement parts for our products. When placing an order for parts, please supply a complete description of the item, quantity required, RO. number, and shipping information. We attempt to ship orders the day they are received, orders received after 12:00 noon will ship the following work day. We do not have a minimum order requirement at this time, however we certainly appreciate your efforts to consolidate your orders whenever possible. Payment Terms are NET 30.

RETURN MATERIAL AUTHORIZATIONS: Material can be returned to CAPCOM USA only in the following situations:

  • Parts, return for credit. A parts order was processed incorrectly, ie; wrong items were shipped, wrong quantity was shipped, etc.
  • PCB, Repair & Return. A PCB requires repair by CAPCOM USA's technical staff.
  • PCB, Return for Credit. A PCB is being returned for credit to satisfy an Advance Exchange transaction.
  • Other, parts are being returned for engineering analysis, etc., only with prior consent of Customer Service or Sales department. To obtain a Return Material Authorization, please contact CAPCOM USA's Customer Service department. Describe the transaction and request an RMA number. The outside of the package must be clearly marked with the RMA number. Packages not displaying an RMA number will be returned un-opened.

REPAIR & RETURN PCBs: CAPCOM USA staffs qualified technicians to assist your repair department. In the event you have a CAPCOM USA PCB that is out of warranty and requires repair, we can provide repair services to you. When requesting an RMA number for a Repair & Return, indicate the type of PCB being returned for repair, PO. number, and shipping information. Repairs will be processed within 1 working day of receipt of defective item. Labor charges are $40.00 per hour plus parts. If the initial estimate indicates that the labor will exceed 1 hour, our technicians will call and request authorization to continue the repair. Payment Terms are NET 30.

WARRANTY REPAIRS: During the initial 90-day warranty, customers who’s accounts are current are eligible for an Advance Exchange PCB. When calling for an Advance Exchange PCB, please supply a complete description of the item needed, game serial number for warranty verification, PO. number, and shipping information. You will be issued an RMA number for the return of the defective PCB. Terms for Advance Exchanges are NET 15. If the defective PCB is not returned within 30 days, no additional Advance Exchanges will be issued until the offending PCB is returned, or the invoice is paid in full. If the PCB is not returned until after 90 days, the warranty will be voided, and the customer will be liable for all repair charges. It is our goal to constantly improve and better our services to you. Your cooperation with the above stated policies will help us greatly to reach this goal. If you have any comments or questions, please telephone our Customer Service department. We will make every attempt to tailor our services accordingly.

Page 5

Installing Your New

New Game Package

Table of Contents

Power and Monitor Requirements. ..... 0.2... 0.0000 eee 4 New Game Package Contents ............ 0.0.6 cece cece eee 4 Recommended Tools and Supplies ............. 000000 eee eee 5 Dip Switch Tables... 0.6.2. 6 Game Description... 1.0.2.0... 2.2.00 0 0c eee 7 Installation Procedures ... 1.6... eee 8

Helpful Hints... 0... eee 14 Control Panel Positioning ............. Ove cee cece tee e te ee te eeeeeees 15

Main Harness Connections. ... 2.6... 6 eee 16

Warranty Registration Card... 0... 2. cee 17

Page 6

POWER REQUIREMENTS MONITOR REQUIREMENTS

+5 VDC Horizontal Mount Raster Scan +12 VDC Negative Composite Sync

NEW GAME PACKAGE CONTENTS

1 Main Printed Circuit Board (PCB) 1 Control Panel Overlay 1 Set Legs, Bolts, & Spacers 1 Plex Control Cover 1 Connecting Wire Harness 1 Set Side Graphics 1 Eight-Way Joystick 1 Monitor Card 6 Player Button Assemblies 1 Service and Installation Manual 1 Marquee

Note: Replacement accessories available through your exclusive Capcom distributor

4.

Page 7

Recommended Tools and Supplies

CAPCOM new game package. Phillips and Slot Screwdrivers Socket Set Wire Cutters and Strippers Pliers or Channel Locks Planning and Careful Thought Electric Drill 3/32", V4", 7he” Drill Bits 4” Plex Bit 13/46” Chassis or Sheet Metal Punch 11/4," Plex Hole Saw Glass of Water and a Snack Small File Razor Knife and Sharp Blades Straight Edge Painting Supplies (if you do your own painting) Paint Brush and Paint (don’t forget the primer) Paint Roller and Pan Sand Paper Putty Knife and Wood Putty Staple Gun and Staples Soldering Iron and 60/40 Resin Core Solder Vacuum Cleaner Assorted Fastening Hardware Shrink Tubing: 3/32”, %/3", 3/16” Masking Tape 3%.” OR 4” Wire Ties Spray Window Cleaner and Rags (baby diapers work GREAT!)

Dip Switch Tables

Optimize Your Profits Thorough Research shows that two and a half minute games both satisfy players and also keep the quarters flowing. If games aren’t running about two and a half minutes long, then collections probably aren’t at their peak. You’ll want to tailor your game to your location. The trick is to adjust a few DIP switches. (See the chart in this book.) It’s easy!

Page 8

venctvWane

DIP SW (A)

TEMDESCRIPTION72E}45673S

1COIN1 CREDIT | OFF | OFF | OFF 1 COIN2 CREDITS|__ON | OFF | OFF 1 COINS CREDITS| OFF | ON | OFF 1 COIN4 CREDITS|__ON | ON | OFF COIN 1 2COIN1 CREDIT | OFF | OFF | ON 3 COINS 1 CREDIT ON | OFF | ON 4COINS1CREDIT | OFF | ON ‘ON *

2 COINS 1 CREDITONONONONONON

1 COIN 1 CREDIT OFF | OFF | OFF

1 COIN 2 CREDITS‘ONOFF_|_OFF
COIN 21 COIN 8 CREDITSOFFON_|OFF
1 COIN 4 CREDITS‘ONON_|OFF
2 COINS 1 CREDITOFFOFF_|_ON
3 COINS 1 CREDIT‘ONOFF_|_ON
4 COINS 1 CREDITOFF‘ON,‘ON

When all switches 1-6 are “or Game starts with 2 coins (1 credit) and continues with 1 coin (1 credit)

DIP SW (B)

TEMDESCRIPTION72345678
VERY EASYON_|_ON | OFF

OrF_[ ON | OFF ON _|_OFF | OFF

DIFFICULTYNORMALOFF | OFF | OFF

LEVEL OFF | OFF | ON ON | OFF | ON OFF_|_ON ‘ON

VERY DIFFICULTon | ON‘ON

DIP SW (C)

TEMDESCRIPTION723456Z8

NORMAL OFF SCREEN FLIP a On

‘SOUND DURINGWITH SOUND.OFF

DEMONSTRATION, one [WITH OUT SOUND ‘ON

WITH CONTINUE OFF ileal aa WITHOUT CONTINUE ‘ON GAME MODE OFF

TEST MODETEST MODEON
  • Thick characters when shipped.
Page 9

“DYNASTY WARS” Players on horseback fight an uphill battle against warlords of ancient China. The action is non-stop as you dodge arrows, leap through flames and smash down the gates to one of the warlord’s castles.

Page 10

Installation Procedures

Something to Think About Your final product will be a new game. You have made a wise decision to transform a game that has seen better days in the all

important cash box into a new game. This is by far the most cost effective alternative to maximize the return of your initial investment. All you provide is the cabinet with a power supply and a monitor. Oh yes, you will need a touch of elbow grease. And that’s it! We provide the rest. The end result is . . . a new game at a very low cost. Fact: Spend a little time on the cabinet’s appearance (i.e. marquee, control panel, and cabinet graphics). With a little paint, some wood putty and new lights, you will raise the profits of any game . . . especially with the introduction of a new game package. The new game look should always apply to the inside of your game as well as the outside. A few wire ties and shrink tubing on your harness; some fastening hardware on your subassemblies and a sweep with the ol’ vacuum cleaner will ensure that unnecessary glitches do not occur. Remember: You are creating a new game. If you have any questions or just need some advice on any of your new game transformations, don’t hesitate in giving a member of our technical staff a call.

Let’s Get Our Hands Dirty

Preparing the Original Game for the New Game Remove the following:

1.Main Logic Board(s)4.Monitor Bezel
2.Control Panel5.Marquee
3.Monitor Plexiglas6.Graphics

| would recommend painting your cabinet to give it a fresh new look. (If it is geographically inconvenient to make use of our facilities, you may consider having an auto body shop take care of your painting needs.) If your cabinet has wood grain sides; remove old graphics and adhesive (adhesive may be removed with lacquer thinner. If you intend to use your original plexiglas, be sure it is in mint condition or it should be replaced. Thoroughly clean out your cabinet.

Page 11

Time to Install Your New Goodies

Before You Start . . . Remember DO NOT Do this Work with the Power On!

Logic P.C.B. Cage Mount the logic cage securely (away from power supply). A Mark and drill pilot holes (3/32”). B_ Place the logic cage (bottom) over the holes and secure it with the supplied wood screws. C Install the PC.B. into the logic cage. Use feet and spacers supplied and adjust them so that the screws will go through the slots in the cage bottom.

Note: Leave the cage cover off until you have attached the entire wire harness and have tested the game for proper operation.

Wire Harness

Attach the wire harness connector to the main logic board. CAUTION: Sometimes the connector is not keyed and it is very easy to install it reversed on the logic board. Even if it is keyed, always triple check to be sure the wire inputs were connected correctly to the connector and the connector to the logic board.

Connecting the Wire Harness to the Existing Wires When you hook up the control panel, power supply, monitor or other subassemblies that remain in the game cabinet to your new wire harness, try and use their existing secondary connectors.

  • Cut the original wire approximately three inches from the original connector. Strip off about one half inch of insulation.
  • Solder the new wire designated for that position to the original wire you just stripped.
Warning: DO NOT JUST TIE THE WIRES TOGETHER. THIS CAN CAUSE NAGGING INTERMITTENT PROBLEMS THROUGH LOOSE CONNECTIONS OR OXIDATION OR BOTH. Always take the time to do it right.
  • Melt shrink tubing around all your in-line wire connections. Do not use electrical tape. Tape could unravel over a period of time due to the cabinet heat and cause you a great deal of trouble.
  • Use wire tie wraps, and secure the cable to the cabinet whenever it seems necessary. Remember this is a new game, not a sloppy conversion.

Power Wires

  • Connect the wires that are designated for your power supply. You will need a supply of +5V, +12V & ground. Your new game package may not require all of the voltages that were used in the original game. Tie off any unused wires.
  • You will notice that you probably have more than one wire for each voltage. It is a good idea to use all wires supplied (double up if it is necessary). This will help to ensure that you don’t overload the edge connector pins and cause them to ‘‘burn’’.
Page 12

Monitor Wires

You will be connecting the wires designated for the RED, GREEN & BLUE video guns along with the SYNC & GROUND wires.

NOTE: . . . CONCERNING SYNC: Your new game only calls for one sync wire connection, this is called composite sync (horizontal and vertical tied together). This composite sync is also negative. Most monitors have supply positions for both negative and positive sync. You can check your monitor manual or call our technical department for assistance.

Speaker Wires Find the two wires that are designated for the speaker and hook ’em on up.

Coin Door Wires

  • Connect the designated wires to the coin switches and meter.
  • You can connect your door lamps to the unused —5V power supply. Some games have separate power outputs for the coin door lamps.
  • Be sure to clean and lubricate your old coin mechanisms. Keep the money coming in.

Guess What?

You are almost done with the electrical connections of your new game. All you have left is the control panel wiring. But we are going to hold off on that for right now. We have a few other things we need to do first. So why don’t you go ahead and get yourself a drink of water and stretch your legs. When you return, we can take a fresh look at your progress and then move forward.

Smoke Test

What Test?

Don’t worry. All this means is that you are ready to apply power to the system for the first time and you pray that there will be no smoke from a simple oversight. You are just about ready to power up the logic board. But first we need to recheck your work.

  • Carefully inspect the game for loose power wires, exposed connections and extra fastening hardware.
  • Make sure the logic board, board cage, monitor, and power supply are securely fastened in place.
  • Double check the connectors to be sure they are wired and connected properly.
  • Set the dip switches on the logic board to the factory recommendations.
Page 13

Time to Apply Power: Look and smell for smoke. (TURN OFF IMMEDIATELY IF ANY IS NOTICED) Listen for game sounds. If after one minute you have not heard any sounds: 1. 2.

A) B) Cc) Check for proper dip switch settings. Adjust volume control and check speaker connections. Check the +12V power supply to the logic board.

NOTE: If you do get sounds, but they are a little fuzzy, switch the wires around on the speaker. See page 12 for more helpful hints. How is the monitor image? A)

B)

Cc) Is the picture in sync? If your picture has the top and bottom halves of the screen reversed and it will not stop rolling, change your sync polarity on the monitor. (Positive to negative). If your monitor does not have dual polarity positions for sync, then you will need to reverse the sync yourself by installing a simple one I.C. circuit between the logic board and the monitor. (The following illustration shows a hookup for both composite and separate syncs.

HORIZONTAL SYNC INPUT FROM PC.B. 5 Veco (OR COMPOSITE SYNC INPUT) HORIZONTAL SYNC OUTPUT TO MONITOR (OR COMPOSITE SYNC OUTPUT) VERTICAL SYNC OUTPUT FROM PC.B.

VERTICAL SYNC OUTPUT TO MONITOR 74LS04 NOT USED

NOT USED

GROUND

G07 MONITOR SYNC MODE

  • Replace R314 from 3902 to 1.8KQ resistor
  • Replace C303 from .1yf 35V cap, locate ‘‘+’’ side of cap to collector of X305
  • Replace C501 with .1pf (old C303)

Now how’s your picture? e Is it centered? ¢ Is it too bright or dim? Is it in focus? Check your monitor manual for these adjustments. If your screen looks ‘‘off”’, then your new game transformation may have been in vain. So let’s take the time to make the monitor look great. Is the picture upside-down? Dip switch 5 on switch bank ‘‘C’”’ should solve your problems.

Ate

Page 14

Control Panel Assembly

  • Remove the buttons, joysticks and wire harness and put them aside for now.. Do not remove the original panel overlay until the new holes have been drilled.
  • Mark positions on the panel for the new holes. CAPCOM supplies a clear 1/8” thick of plexiglass with every new game package to convert the control panel. We feel that your new game investment is well worth protecting. ..and the control panel is the first place to show wear and tear. ¢ You will need to cut this piece to size. Use the control panel as a template.
  • Use a razor knife to score the plexiglass deeply. Then use a pair of pliers to break away the extra plexiglass.
  • Now drill the holes in your panel that you have marked off for the buttons, joystick and bolts.
  • Drill the same holes on your plexiglass panel protector. Once again use your panel as a template. Hint: To avoid chipping while you are drilling the holes, place the plexiglass securely on a soft wood surface and use a plexiglass drill bit and hole cutter.
  • The holes are now all cut. Smooth them out on your panel and plexiglass with a fine toothed file.
  • Remove the original graphics overlay from the panel. Clean up the panel and install your CAPCOM graphics. Make It Easier: Peel the top half of the protective backing off of your graphics. Start from the center and smooth out your overlay. Make sure you have about an inch extra coming off the top. No bubbles please. Now peel off the bottom half and do the same as you did for the top.
  • Adhere the instruction and function labels.
  • Install the Plex Control Cover over your completed new game panel.
Note: Be sure to bolt the plexiglass securely to the panel.
  • Mount the joystick and the buttons to the panel and wire them up. (Use the existing Panel wiring if possible)

Marquee Installation

Using the original marquee as a template, Center your new game marquee graphics and score the new marquee deeply to fit the cabinet. Break off the excess with pliers. Be sure the light behind the marquee works. Everything should always work on a new game. Take your time. . .Don’t forget this is going to be a new game.

Page 15

Side Graphic Installation

Be sure sides of game are clean and free of old adhesive, dust, etc. Mark position of decal with eraseable pen or pencil (centered on upper half of cabinet). Peel off top 1/4” of decal backing and apply to cabinet with a smoothing motion (use a soft rag). Continue peeling off backing and smoothing. Remove any small bubbles with a pin or razor blade (pop them!)

Finishing Touches

Check the game inside and out for any imperfections. Secure any loose wiring or fastening hardware. Make sure the coin door is tight and the coin mechs are well adjusted. A game is no good to anybody if you can’t get a coin into it. Once again go over every step of this new game transformation in your mind. Be sure everything is correct and to your liking. Power up the game. A. Check all the coin switches. (Does the coin meter work?) B. Play your new game. © Are all the player controls working?

  • Are the game sounds present? ¢ Is the volume level proper? ¢ Are the dip switches set properly? Well, that’s about it. Good Luck.
Page 16

Helpful Hints

Simple audio check for Board: TYPICAL AUDIO CIRCUIT FOR CAPCOM BOARD:

volume control +12VDE CONNECT EARPHONE BETWEEN POINT ‘‘A’” & GROUND. AUDIO FROM CPU BOARD SHOULD BE HEARD. Edge connector (see wiring list for correct pins)

speaker connections NEXT CHECK POINT “B” AND GROUND. ADJUST POT FOR LOUDNESS IN EARPHONE.

CHECK POINT “‘C”” & GROUND FOR INPUT AUDIO TO PIN 3 OF HA13001 AUDIO CHIP. audio in

Also make sure Ground from +5VDC and Ground from +12VDC ARE TIED TOGETHER. IF GROUNDS ARE FLOATING, you could have audio problems.

NOTES:

Page 17

RIGHT ATTACK

TACTICS 1 & 2 player locations

Control Panel Positions

« PCB CONNECTOR

JAMMA STANDARD

¢ CRT MONITOR

HORIZONTAL SCREEN

© CONTROL PANEL

8 WAY JOYSTICK LEFT RIGHT O

ATTACK ATTACK 8 WAY JOYSTICK TACTICS

© MAXIMUM CREDITS: 9

« DIP SWITCH

<= DIP Sw (A)

B|_1-6 | «——_—_ DIP sw (B)

c[1-6 | «———. p Pswc)

VOLUME CONTROL | O JAMMA

Page 18

MAIN HARNESS CONNECTIONS

Wire Color Solder Side Parts Side Wire Color

Black Ground

Black Ground

Red +5VDC

Red +5VDC White -5VDC Yellow +12VDC KEY

Brown Counter 2

Red Not Used

Black Speaker (—) Blue Not Used

Green Video Green

Gray Video Sync Red Service SW

Brown Not Used White Coin 2 Gray 2P Select Violet 2P Up Blue 2P Down

Green 2P Left

Yellow 2P Right Orange 2P Left Attack Red 2P Right Attack Brown 2P Tactics

Blue Not Used

Blue Not Used

Black Ground

Black Ground Ground Black

Ground Black

+5VDC Red

+5VDC Red

-5VDC White +12VDC Yellow KEY

Counter 1 Brown

Not Used Red

Speaker (+) White Not Used Red

Video Red Red

Video Blue Blue

Video Ground Black

Not Used Brown

Coin 1 White

1P Select Gray 1P Up Violet 1P Down Blue

1P Left Green

1P Right Yellow 1P Left Attack Orange 1P Right Attack Red 1P Tactics Brown

Not Used Blue

Not Used Blue

Ground Black

Ground Black O/@IN OM AAW) MyM) = —-|0/a]0 |e] |IN|/<|x/S/</C\Alo/D/V/Z/Z\r-|xAlc |r| n|mjojol|ol|>

Page 19

CAPCOM GAME OWNER:

Please fill out card and register for Free drawing at COIN-OP SHOWS. YOU NEED NOT BE PRESENT TO WIN.

Remember to fill in S/N of PCB (S/N IS REQUIRED FOR DRAWING).

REGISTER FOR FREE DRAWING

CAPCOM U.S.A., INC. 3303 Scott Boulevard Santa Clara, CA 95054

Page 20

CAPCOM

3303 Scott Boulevard

Santa Clara, CA 95054 (408) 727-0400

COMPANY NAME

LAST NAME FIRST NAME

ADDRESS

CITY STATE ZIP CODE AREA CODE PHONE NO.

PRODUCT PURCHASED: DATE OF PURCHASE PURCHASED FROM: MONTH DAY _ YEAR sn COT HOW WOULD YOU RATE THIS GAME: EXCELLENT VERYGOOD() FAIRC] POOR O

HOW DID YOU HEAR ABOUT THIS GAME: MAGAZINE [1 FRIEND 1 OTHER DO YOU OWN ANY OTHER CAPCOM ARCADE GAMES? YES NO PLAN TOBUYIN NEAR FUTURE (1

WHAT TYPE OF ROUTE DO YOU OWN: ARCADE [] SMALLROUTE (] LARGE ROUTE 1 HOW MANY GAMES DO YOU OWN

WHAT CAPCOM ARCADE GAMES ARE YOU FAMILIAR WITH: SPEED RUMBLER (] SECTIONZ(] LEGENDARYWINGS AVENGERS] 19430 STREETFIGHTER (] OTHER (

COMMENTS: