CATHODE RAY TOMES

VS Dr.Mario

Vs. Dr. Mario (Nintendo, 1990) · Document · 5 pages · 3 sections · original scan

Page 1

FOR SERVICE CALL: 1-800-633-3236

VS.- PAK

INSTALLATION MANUAL

For: VS.UniSystem™, VS.DualSystem™, and VS.Table

INSTALLATION INSTRUCTIONS

1 + CONTENTS OF PAK 1 VS. Dr.Mario™ Expansion PCB 1 Nameplate overlay 1 Instruction label (Table) 1 DIP switch / Factory recommended settings sheet 1 Authorization label 1 Installation Manual oooooodo

2 + INTRODUCTION

“This VS.-Pak contains the parts to:changeany VS:UniSystem, VS.DualSystem or VS. Table game. Please be sure to save your PPU ROM kit and any literature from the VS. game that you are converting SO you can change back to that game in the future if you so desire. By doing this, you will be able to continue to build your library of games for your VS. systems.

3 + TOOLS NEEDED + Small FLATHEAD screwdriver «Medium PHILLIPS head screwdriver + Staple gun + 9/32°(7mm) socket drive or adjustable wrench (for Table only)

VS Pak-OrMano (911-90 rw and ®@ are vacemarks of Nintendo of Amenca inc. © 1990 Nintendo

Page 2

4 + INSTALLATION IN VS. UPRIGHT CABINETS A. Prepare a plexiglass header for the new nameplate overlay by eitier removing the old header and overlay from the cabinet or cutting a new piece of plexiglass.

NOTE: If you are cutting plexiglass for a new header, the maximum size of the nameplate overlay is 5 - 3/4” tall by 24 - 1/4" long. To remove the old header, remove the four (4) top trim screws and top trim. (For the Dual cabinet it is necessary to also remove one (1) additional screw and slightly pull away the plastic center piece.) Then slide the old header up and out of the game. (See Fig. 1 and 2)

@ Cut the nameplate overlay to fit the header you are using, being careful not to remove any part of the instructions or game name. C. Adhere the authorization label to the new nameplate overlay in a location that will not cover any part of the instructions or game name. . Using SCOTCH brand (clear) tape (not provided), tape the new nameplate overlay to the back of the header. Replace the new header and top trim. Replace and tighten the top trim screws. (On the Dual cabinet, make sure that the header fits back under the plastic center piece before replacing the screws.) (See Fig. 1 and 2) Oo

m

NAMEPLATE OVERLAY TOP TRIM TOP TRIM

Page 3

a

F. Remove the back door and staple the DIP switch / Factory recommended se#.qgs sheet next to the old label.

NOTE: Do not remove the old label. (See Fig. 3)

DIP SWITCH LABEL 5 + INSTALLATION IN VS. TABLE A. Unlock and open the table lid. Remove the four (4) 9/32" nuts holding the plexiglass instruction label cover. B. Remove the plexiglass cover and carefully remove “the old instruction label and save for future use. C. Remove the paper backing strip on the new instruction label and install. D. Replace plexiglass cover and four (4) nuts.

NOTE: Do not over tighten the nuts or you may damage the plexiglass. (See Fig. 4) 4

E. Adhere the authorization label to the side of the table just under the FCC label. Do not cover up any old labels. (See Fig. 5)

mm Tape the DIP switch / Factory recommended settings sheet onto any unused surface inside the table housing..(Remove and save the old label if necessary.

AUTHORIZATION LABEL

Page 4

6 » UPRIGHT / TABLE SOFTWARE INSTALLATION A. For two monitor systems, if VS. Dr.Mario is to be installed in the main (LEF7) side of the

B. cabinet, then remove the existing PPU and CPU chips (2A03), in locations 2F anc 2 on the CPU PCB, and remove EPROMS in locations 1A, 1B, 1C, 1D, 2A, and 2B. For installation in the sub (RIGHT) side, use locations 8F and 8J, and EPROMS in locations 6A; 6B, 6C, 6D, 8A, and 8B.

Insert the VS. Dr.Mario Expansion PCB into the two (2) bare 40-Pin DAP IC sockets on the CPU PCB. Locations 2F and 2J for the main (LEFT) side or 8F and 84 for the.sub (RIGHT) side.

CAUTION: Be sure to imsert the Expansion PCB with the chips loaded in the same

. Insert CPU chip 2A03 into the 40-Pin DIP IC -

. For one monitor systems, VS. Dr.Mario must direction as the other IC’s on the CPU PCB. Inserting the Expansion PCB backwards may cause damage to both the CPU PCB and the Expansion PCB.

Insert the VS. Dr.Mario Expansion PCB firmly into the IC sockets to prevent failure and carefully check all 40-Pins for proper connections. GLOLCL CLOT EL ECL EL ELELEETL,

socket, location U2 on the Expansion PCB, with the chips loaded in the same direction as the other IC's on the Expansion PCB.

use locations 8F and 8J, sub side of the CPU PCB. (See Fig. 6) Recceeeneennnene@recc cS coos

Fig. 6 CLL PC DEEL ELET IED ED ELE

7 + FACTORY RECOMMENDED DIP SWITCH SETTINGS Check and change the DIP switch settings on the CPU PCB so that they match the DIP switch / Factory recommended settings sheet.

8 + FINAL CHECK LIST Q Q Q

= I Gf FCC door installed correctly Nameplate overlay installed correctly and on the correct side DIP switches set correctly (See the DIP switch / Factory recommended settings sheet for VS. Dr.Mario) ! c'>y buens and joysticks function correctly

  • wor on monitor looks good, monitor and front screen glass are clean (On the one player game, the “VIRUSES” in the lower left corner of the screen should appear RED, YELLOW and BLUE. The background behind the pill bottle should be black) The coin acceptors give credit
Page 5

DIP SWITCH / FACTORY RECOMMENDED SETTINGS

Vs. Dr. Mario Switch SW1 (SW2) ~

Increase drop rate eee after x pills 9) Off | On 8] On | Off a 7| Off | Off Defauli Virus Level 7 5 Off | On 3 On | Off “ee 1 L Off | Off

Drop rate speed up Fastest On ! On

Fast Off | On Med On | Off

LSlow|~| Off | Offne
Free PlayYes|q“fp4On
NoOff|*
Attract Mode Music|!lon|*
  • * * Recommended DiP switch settings Please Note - As players gain skill it is wise to increase the difficulty settings in order to realize the greatest reiurns. Please use the following guide when adjusting the difficulty.

Increase drop rate Decrease this number in order to speed up games which seem to “last all day" Default Virus Level _ Increase this-number to give players a greater challenge when they begin play by increasing tHe-number of viruses to te eliminated Drop rate speed up Increase this setting in order to challenge only the best players by increasing the speed at which the pills will fall