PC10 Kit Manual for Installation in VS UniSystem
PlayChoice (Nintendo, 1988) · Kit Manual · 28 pages · 11 sections · original scan
Play Chote’
KIT MANUAL
FOR INSTALLATION IN
VS. UniSystem'
©1988 Nintendo’of America Inc.
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
vi.
Vil.
Vill. TABLE OF CONTENTS
Introduction
Contents of PlayChoice™ kit
List of Tools Needed
Replacement Process Step-by-Step
Final Check Sheet and Adjustments
Wiring Diagram and PCK-10-LED Schematic
CPU P.C. Board
Reorder parts list 5-12
13-16
INSERT
INSERT
17-23
I. INTRODUCTION
PlayChoice™ Kit
This PlayChoice™ kit enables you to change any Vs. UniSystem* Upright into a single monitor PlayChoice™ Upright. This includes all Donkey Kong*, Donkey Kong Jr.*, Donkey Kong 3*, and Popeye** Uprights that have already been converted to a VS. Unisystem*
Before you begin, be sure you are properly prepared. Thoroughly read this Instruction Manual to familiarize yourself with the proper procedures. Make certain that you have all the tools necessary to complete the process.
If you have any questions, please call Nintendo Service at:
1-800-633-3236
Donkey Kong, Donkey Kong Jr., Donkey Kong 3, and VS. UniSystem are registered trademarks of Nintendo of America Inc.
A trademark of King Features Syndicate, Inc.
I. CONTENTS OF PLAYCHOICE KIT
Part Name Quantity = = Remarks
PCKG-UP Complete Control Panel Assy PCK-1 CPU PC Board Assy LED PC Board Assy PCKG Name Plate Plexiglass PCKG Name Plate Overlay PCKG Side Decal Card Spacer KGLS-4S. LED PC Board Bracket UP 36P 080 Edge Harness PCK 1-UP Adjustment Label PCKG1-UP-US Serial Number Plate FCC Class A Label CS-7 Screw Tie Down Wood Screw 3.5 x 13 Wood Screw 3.1 x 10 PCK Kit Manual PCKG-UP Authorized Sticker FBI Warning Label Cable Tie Black
W/Double Back Tape aoaaannwsaaa
oases Raw s
lll. LIST OF TOOLS NEEDED
Phillips Screw Driver Electric Reversing Drill Phillips Bit (for drill) Staple Gun 10mm Nut Driver or Adjustable Wrench
IV. REPLACEMENT PROCESS STEP-BY-STEP
- Remove Marque/Header (see illustration 1-1) Remove four (4) top trim screws. Remove marque plexiglass. Adhere PlayChoice™ overlay to new plexiglass. Insert new PlayChoice™ marque/header into game. Replace top trim and four (4) top trim screws. moom>
- Remove old Control Panel and Front Screen (see illustration 1-2) A. Undo control pane! hold-down clamps, (access through coin-mech door). B. Disconnect harness and remove control panel. C. Remove front screen.
Replace Side Decals. mo OM>
m Remove back door. Disconnect monitor wire harness connections. Using Phillips driver and 10mm nut driver, remove four (4) MS x 16 machine screws and six (6) carraige bolts and remove monitor (see illustration 1-3) Remove old side decals. Apply new PlayChoice™ side decal (see Decal Application sheet on Page 12 and Illustration 1-4) Replace monitor.
Remove old 36 pin edge harness, old PC Board and modify FCC cage.
A. Remove the 36 pin edge harness completely from game. (This is the harness that connects to the top of the FCC Door) Remove FCC Door. Remove old PC Board. Move the wood PC Board mounts (both top and bottom) to the far right of the FCC Cage if necessary. (see illustrations 1-5 & 1-6) pon
- Mount LED Display
A. Using two (2) 3.5 X 13 wood screws, fasten the LED PC Board bracket onto the upper right corner under the speaker grill and 1" back from the front screen. (see illustration 1-7) Attach the two (2) KGLS-4S Card Spacers to the LED PC Board. (see illustration 1-8) Connect the 12 pin connector from the new 36 pin edge harness to the LED PC Board. (see illustration 1-8) Attach the LED PC Board to the LED PC Board Bracket. (see illustration 1-8) Using three (3) 3.5 X 13 wood screws and three (3) CS-7 screw tie downs, fasten the wire harness as shown. (see illustration 1-7) mo oO ®
- Install Main PCB
Install PlayChoice™ game software into the main PlayChoice™ PC Board. Slide PC Board assembly into FCC cage with software cards pointing to the left. Connect the 36 pin and 44 pin short FCC harnesses from the FCC door to the main Playchoice™ PC Board. Attach the FCC door to the FCC cage. Attach the 36 pin and 44 pin main harness connectors to the FCC door. Route the 36 pin and 44 pin harness as shown (see illustration 1-10) ™mS oOp>
- Replace Front Screen and Install new Control Panel
A. Install the front screen. B. Connect the control panel wire harness and fasten down control panel. (see illustration 1-9)
1-10
9. Screw on new serial number plate next to old plate.
Attach FCC Class A label (see illustration 1-12)
A. Remove old FCC label B. Put on new FCC label and staple all four corners
- Attach FBI sticker
A. Place label on back door just under lock (see illustration 1-13) B. Staple all four (4) corners
- Install new PCK1-UP Adjustment Label
A. Adhere label to inside surface of back door. B. Staple all four (4) corners
Side Decal Application
Step 1.
Start by peeling the protective backing "A" down about 6 inches from the top.
Place decal in desired position. Pull down slowly the remainder of the protective backing of
While doing this, use a soft cloth to smooth decal onto side board, moving from top to bottom of decal.
Step 2.
Fold remaining decal back, exposing the unprinted side. Begin to peel protective backing "B" from center to right hand side "slowly."
Using soft cloth smooth decal onto side panel by running hand from top to bottom of decal, moving outward to the right hand side.
Front View
Vv. Final Check Sheet and Adjustments
- New serial number plate installed (MANDATORY).
- New FCC Label installed (MANDATORY).
- PC Board adjustments made. (See pc board adjustments page 13).
Monitor adjustments made (See monitor adjustments page 14-16).
- Coins give credit.
- Controls on operation panel functioning.
- Sound checked. OOOGQ oO OaoQa
- LED PC Board indicate player time.
PCK-CPU PC BOARD
A_ Color Adjustment
fo ee oe Ld Go C Jy é a Ce [e)
PCK1 - CPU PC BOARD
The fixed variable registers (VR 1, VR 2, VR 3) have already been preset and do not need adjustment. If, however, color does not seem correct, VR1, VR2 and VR3 may be adjusted.
Adjustment of Video Monitor
To From : 7 PCB Green Gain Video Monitor Game PC Ue Main pea 6P—600 Video Harness Signal PCB
This Signal PCB is only attached to TPPU-20-00 :Video Monitor (32 Type) 20-EZV (R-C).
BRIGHT
‘————~ SOUND VOLUME
H HOLD a Fuse 4A (Slow Blow) SP
¢ lf 4 ff @! i Q
Video Monitor
ae Main PCB
Fuse 0.3A (Midget Type)
Do not touch the inside of the Video Monitor. It contains many parts supplied with high voltage.
Positive ”
SUB BRIGHT a“ @ a
Negative ZA
Ble Gi macy, lue Gain Sa Positive/Negative Red Gain Video Switch Green Gain’
DEGAUSS SWITCH From 6P-600 H-HOLD Video Harness V-SIZE
v-HOLD
H-CENT U a
BRIGHT Mon Pw 8
SOUND VOLUME
Fuse (Slow Blow) 3A, 125V-—+
Fuse (Slow Blow) 2.5A, 125V
Fig. 6 Video Monitor : [Y51 Type] XM-2001N
Do not touch the inside of the Video Monitor.
It contains many parts supplied with high voltage.
Adjustment of Horizontal Width
Using a standard 2.6mm hex non-conductive core alignment driver, carefully turn L453 counterclockwise for a small horizontal screen size. L453 is located in the rear of the monitor just under the deflection yoke.
Alignment Tool
\ Heat Sink
UY Turn this way for
a smaller horizontal screen size
Main PC Board VI. REORDER PARTS LIST
PART NO. ORDER NO. DESCRIPTION (Reference Designations and Locations)
| PCKU-21-01 | 7929 | PCK1 CPU Complete PCB Assembly | |
| PCHU-21-11 | 946 | Z80A Microprocessor | (5X) |
| PCHU-21-12 | 945 | RP2A03E Microprocessor | (1H) |
| PCHU-21-13 | 4460 | RP2C03B PPU | (3H) |
| PCKU-21-14 | 7936 | 27128 16K-Byte EP-ROM 300ns PCK 1-C-8T | (8T) |
| PCKU-21-15 | 7937 | 2764 8K-Byte EP-ROM 300ns PCK 1-C-8K | (8K) |
| PCKU-21-16 | 7938 | 2764 8K-Byte EP-ROM 300ns PCK 1-C-8M | (8M) |
| PCKU-21-17 | 7939 | 2764 8K-Byte EP-ROM 300ns PCK 1-C-8P | (8P) |
| PCHU-21-18 | 2060 | TMM2115BP-15 2K-Byte RAM 150ns | (2K) |
| PCHU-21-19 | 2061 | HM6116 ASP-20 2K-Byte RAM 200ns | (4K, 8R, 8V) |
| PCHU-21-20 | 4811 | TC5517 CPL-20 2K-Byte C-MOS RAM 200ns | (8W) |
| PCKU-21-21 | 7940 | N82SI29N 256x4-Bit Bipolar ROM PCK1-C-6D | (6D) |
| PCKU-21-22 | 7941 | N82SI29N 256x4-Bit Bipolar ROM PCK1-C-6E | (6E) |
| PCKU-21-23 | 7942 | N82SI29N 256x4-Bit Bipolar ROM PCK1-C-6F | (6F) |
| PCHU-21-24 | 2189 | 74LS00 Quad 2-Input NAND | (5H, 8J, 6U) |
| PCHU-21-25 | 2190 | 74LS02 Quad 2-Input NOR | (4U) |
| PCHU-21-26 | 2191 | 74LS04 Hex Inverters | (8D, 3G, 8G, 5J, 7R,7Y, 42) |
| PCHU-21-27 | 2193 | 74LS08 Quad 2-Input AND | (7X) |
| PCHU-21-28 | 2195 | 74LS1 {Triple 3-Input AND | (5P) |
| PCHU-21-29 | 2196 | 74LS14 Hex Schmitt Inverters | (4V) |
| PCHU-21-30 | 2202 | 74LS32 Quad 2-Input OR | (7C, 5T) |
| PCHU-21-31 | 2203 | 74LS42 4 To 10 Decoders | (47) |
| PCHU-21-32 | 2204 | 74LS55 2-Wide 4-Input AND-OR-INVERT Gates | (5K) |
| PCHU-21-33 | 2205 | 74LS74A Dual "D" Flip-Flops (P, CL) | (7J, 7K, 5M) |
| TPP2-06-20 | 2208 | 74LS86 Quad 2 Input EX-OR | (4M) |
| PCHU-21-34 | 2210 | 74LS109A Dual J-K Flip-Flops (PLE, CL) | (4Y) |
| PCHU-21-35 | 2216 | 74LS139 Dual 2 To 4 Decoders | (7H, 2L, 6T) |
| PCHU-21-36 | 2220 | 74LS157 Quad 2 To 1 Data Selectors | (7S, 7T, 7U, 7V) |
| PCHU-21-37 | 2223 | 74LS161A 4-Bit Binary Counters | (6H, 6J, 6K, 6L, 6M, 4R) |
| PCHU-21-38 | 2225 | 74LS164 8-Bit Shift Registers | (8H, 5Q) |
| PCHU-21-39 | 2226 | 74LS165A 8-Bit Shift Registers | (8B, 8C, 7F) |
| PCHU-21-40 | 2228 | 74LS175 Quad "D" Flip-Fips (CL) | (4S) |
| PCHU-21-41 | 2229 | 74LS194A 4-Bit Shift Registers | (6Q, 6R) |
| PCHU-21-42 | 2230 | 74LS240 Octal Bus Inverters (TS) | (5A, 6A, 7B) |
| PCHU-21-43 | 2232 | 74LS244 Octal Buffers & Line Drivers (TS) | (6B, 1L, 2M, 3M, 8S, 5V, 6V) |
| PCHU-21-44 | 2233 | 74LS245 Octal Bus Transceivers (TS) | (1K, 6Z) |
| PCHU-21-45 | 2235 | 74LS259 8-Bit Addressable Latches | (7D, 7E) |
| PCHU-21-46 | 2239 | 74LS299 8-Bit Shift/Storage Registers | (7L, 7N, 7Q) |
| PCHU-21-47 | 2242 | 74LS367A Hex Bus Drivers | (4L) |
| PCHU-21-48 | 2243 | 74LS368A Hex Bus Drivers | (8E, 8F, 5S) |
| PCHU-21-50 | 2247 | 74LS377 Octal "D" Flip-Flops | (6P) |
| PCHU-21-51 | 2267 | 74S04 Hex Inverters | (2G, 6N) |
| PCHU-21-52 | 2259 | 7437 Quad-2-Input NAND Buffers | (4X) |
| PCHU-21-53 | 2278 | 75471 Dual Peripheral AND Drivers | (6C) |
| PCHU-21-54 | 4812 | 74HC10 Triple 3-Input NAND C-MOS | (8Y) |
| PCKU-21-55 | 8004 | TC74HC373 Octal 3-State D-Latches C-MOS | (3K) |
| PCKU-21-55 | 1143 | PST518A Low Voltage Detector | (7Z) |
| PCHU-21-56 | 1445 | LM324 Quad Operational Amplifiers | (3E) |
| PCHU-21-57 | 1443 | LM3900 Quad Operational Amplifiers | (1E) |
Main PC Board PART NO. ORDER NO. DESCRIPTION (Reference Designations and Locations;
| PCKU-21-57 | 7943 | TC 4053BP Triple 2-Channel Multiplexer C-MOS | (5C) |
| PCHU-21-58 | 735 | CD 406 6B Quad Analog Switches C-MOS | (3C) |
| PCHU-21-59 | 2178 | 2SA933 Silicon PNP Tansistor | (Q11,Q12, Q14, Q15, Q17, Q18) |
| PCHU-21-60 | 2179 | 2SA1015 Silicon PNP Transistor | (Q3, Q5, Q7, Q20) |
| PCHU-21-61 | 2184 | 2SC1740 Silicon NPN Transistor | (Q8~Q10, Q13, Q16, Q19, Q20~Q26) |
| PCHU-21-62 | 2185 | 2SC1815 Silicon NPN Transistor | (Q1, Q2, Q4, Q6) |
| PCHU-21-63 | 1003 | ES1F Diode | (D1) |
| PCHU-21-64 | 1012 | 1S5277B Diode | (D3, D4) |
| PCHU-21-65 | 4813 | EGO01Y Diode | (D2) |
| PCHU-21-66 | 1002 | DAN401 Quad Cathode-Common Diode Array | (DA1~DA8) |
| PCHU-21-67 | 4817 | 1.0f 5.5V Electric Double Layer Capacitor (EEC F5R5U105) | (C3) |
| PCHU-21-68 | 680 | 68pf 50V Ceramic-Disc Capacitor | (C44) |
| PCHU-21-69 | 663 | 100pf 50V Ceramic-Disc Capacitor | (C35, C36, C45, C71) |
| PCHU-21-70 | 669 | 180pf 50V Ceramic-Disc Capacitor | (C11, C39) |
| PCHU-21-71 | 675 | 330pf 50V Ceramic-Disc Capacitor | (C2, C6, C40, C41) |
| PCKU-21-71 | 7945 | 470pf 50V Ceramic-Disc Capacitor | (C12) |
| PCHU-21-72 | 664 | 1000pf 50V Ceramic-Disc Capacitor | (C5) |
| PCHU-21-73 | 665 | 0.01uf 50V Ceramic-Disc Capacitor | (C4, C22, C38, C43, |
C80~C83, C86~C89, C91, C92, C94~C 101, C103~C108, C110~C120, C122~C126, C128, C130~C144, C146, C148~C156, C158~C163, C165~C187)
| PCHU-21-74 | 4815 | 0.047uf 50V Ceramic-Disc Capacitor | (C15~C17) |
| PCHU-21-75 | 655 | 0.2uf 12VCeramic-Disc Capacitor | (C21) |
| PCHU-21-76 | 716 | 0.047uf 50V Film Capacitor | (C33, C34) |
| PCHU-21-77 | 685 | 1uf 16V Al Electrolytic Radial Cap. | (C7, C8) |
| PCHU-21-78 | 689 | 3.3uf 16V Al Electrolytic Radial Cap. | (C13, C14, C25, C28, C31, C32) |
| PCHU-21-79 | 683 | 10uf 16V Al Electrolytic Radial Cap. | (C23, C24, C26, C27, C29, C30, C37,C42) |
| PCHU-21-80 | 688 | 33uf 16V Al Electrolytic Axial Cap. | (C9) |
| PCHU-21-81 | 4818 | 47uf 16V Al Electrolytic Radial Cap. | (C47~C50) |
| PCHU-21-82 | 684 | 100uf 16V Al Electrolytic Axial Cap. | (C46) |
| PCHU-21-83 | 4819 | 100uf 25V Al Electrolytic Axial Cap. | (C70) |
| PCHU-21-84 | 687 | 220uf 16V Al Electrolytic Axial Cap. | (C1) |
| PCHU-21-85 | 691 | 470uf 16V Al Electrolytic Axial Cap. | (C20) |
| PCHU-21-86 | 4820 | 3.3uf 16V Tantalum Electrolytic Cap. | (C85, C90, C93, C102, |
C109, C121, C127,C145, C157)
| PCHU-21-87 | 2075 | 0 Ohm Shunt Lead | (R99) |
| PCHU-21-88 | 2076 | 10 Ohm 1/4W + 5% Resistor | (R7) |
| PCHU-21-89 | 2120 | 33 Ohm 1/4W— 5% Resistor | (R32, R37) |
| PCHU-21-90 | 2137 | 510hm 1/4W—5% Resistor | (R8, R19, R23, R27, R31) |
| PCHU-21-91 | 2077 | 100 Ohm 1/4W + 5% Resistor | (R17, R68, R69, R73) |
| PCHU-21-92 | 2082 | 110 Ohm 1/4W —-5% Resistor | (R3) |
| PCHU-21-93 | 2121 | 330 Ohm 1/4W —--5% Resistor | (R13, R14, R18, R21, R25, |
R29, R36, R90, R91, R97, R98, R110, R111, R112)
| PCHU-21-94 | 2138 | 510 Ohm 1/4W — 5% Resistor | (R46, R56, R66) |
| PCHU-21-95 | 2155 | 820 Ohm 1/46W—+ 5% Reisstor | (R1, R2) |
| PCHU-21-96 | 2078 | 1K Ohm 1/4W + 5% Resistor | (R94~R96, R120~R131) |
| PCHU-21-97 | 2099 | 2K Ohm 1/4W 5% Resistor | (R15, R87, R109) |
| PCHU-21-98 | 2105 | 2.2K Ohm 1/4W — 5% Resistor | (R35, R40, R42, R50, R45, |
R52, R55, R60, R62, R65)
| PCHU-21-99 | 2134 | 4.7K Ohm 1/4W -© 5% Resistor | (R43, R53, R63) |
| PCHU-21-100 | 2139 | 5.1K Ohm 1/4W - 5% Resistor | (R4 ,R5, R22, R26, R30, |
R88, R89)
| PCHU-21-101 | 2152 | 7.5K Ohm 1/4W — 5% Resistor | (R16) |
Main PC Board PART NO. PCHU-21-102
PCHU-21-103 PCHU-21-104 PCHU-21-105 PCHU-21-106 PCHU-21-107 PCHU-21-108 PCHU-21-109 PCHU-21-110 PCHU-21-111 PCHU-21-112 PCHU-21-113 PCHU-21-114 PCHU-21-115 PCHU-21-116 PCHU-21-117 PCHU-21-118 PCHU-21-119 PCHU-21-121 PCHU-21-123 PCHU-21-124 PCHU-21-125 PCHU-21-126 PCHU-21-127 PCHU-21-129 PCHU-21-130 ORDER NO. DESCRIPTION (Reference Designations and Locations)
| 2079 | 10K Ohm 1/4W== 5% Resistor | (R12, R34, R38, R41, R44, |
R51, R54, R61, R64, R74, R82, R83, R92, R93, R100~R102, R104, R106, R108)
| 2086 | 12K Ohm 1/4W=_ 5% Resistor | (R71) |
2100 20K Ohm 1/4W + 5% Resistor (R6, R39, R70, R72, R103, R, 105, R107)
| 2080 | 100K Ohm 1/4W== 5% Resistor | (R33, R75) |
| 2101 | 200K Ohm 1/4W + 5% Resistor | (R9~R11) |
| 2126 | 360K Ohm 1/4W == 5% Resistor | (R79) |
| 2154 | 750K Ohm 1/4W == 5% Resistor | (R78, R80, R84) |
| 2081 | 1M Ohm 1/4W= 5% Resistor | (R76, R85) |
| 2097 | 1.8M Ohm 1/4W-+ 5% Resistor | (R81) |
| 2107 | 2.2M Ohm 1/4W=— 5% Resistor | (R77, R86) |
| 2068 | Hex 5.1K Ohm Series Resistor Array | (RM1, RM16) |
| 2065 | Octal 1K Ohm Series Resistor Array | (RM5, RM8~RM10, RM13) |
2071 Quad 68 Ohm Parallel Resistor Array (RM6, RM7, RM11, RM12, RM14, RM15)
| 4821 | NT-01 Resistor Array | (RM2~RM4) |
| 2290 | 500 Ohm Variable Resistor, Red Cap | (VR1) |
| 2289 | 500 Ohm Variable Resistor, Green Cap | (VR2) |
| 2279 | 500 Ohm Variable Resistor, Blue Cap | (VR3) |
| 2411 | 8MHZ Crystal | (X1) |
| 2414 | 21.47727 MHz Crystal | (X2, X3) |
| 2174 | 8-Station, Single-Throw, DIP Bit Switch | (SW1, SW2) |
| 4823 | MINI-BIT Header | (SW3) |
| 2166 | 16 Pin DIP IC Socket | (S6~S8) |
| 2171 | 28 Pin DIP IC!Socket | (S2~S5) |
| 2172 | 40 Pin DIP IC Socket | (S1, S9, $10) |
| 4880 | 96 Pin DIN Connector Receptacle | (CH1~CH10) |
| 4825 | GL-3HD1 Visible Light Emitting Diode | (LED1) |
OPERATION PANEL ASSEMBLY
| ITEM | PART NO. | ORDER NO. | DESCRIPTION |
| 1 | MDST-14-12 | 773 | 8 Way Control Lever Assembly |
| 2 | TNX-23-18 | 808 | 8 Way Guide Plate |
| 3 | TKGU-23-23 | 813 | E Ring 4 |
| 4 | TKGU-23-21 | 811 | Switch Collar |
| 5 | TKGU-23-22 | 812 | Lever Spring |
| 6 | TKGU-23-20 | 810 | Spring Stopper |
| 7 | TKGU-23-13 | 804 | Micro Switch |
| 8 | TKGU-23-17 | 807 | Switch Spacer |
| 9 | TKGU-23-16 | 806 | Bearing Bracket |
| 10 | TMAU-12-15 | 784 | Lever Plate |
| an | TMAU-12-14 | 783 | Control Knob Plate |
| 12 | TMAU-12-16 | 785 | Control Knob Collar 8L |
| 13 | TMAU-11-18 | 778 | Knob with Shaft 80.5L |
| 14 | PCKG-12-11 | 7928 | Operation Panel Base |
| 15 | TKGU-23-12 | 803 | Switch Button Bracket |
| 16 | TMAU-34-18 | 821 | Micro Switch VL 12L (Straight) |
| 17 | MDSU-12-17 | 896 | Black Sponge, 2 x 10 x 580L |
| 18 | TKGU-23-26 | 814 | Nut Plate |
| 19 | TKGU-23-34 | 818 | Pal Nut M16 |
| 20 | MDST-12-21 | 932 | Button Assembly (Black) |
| at | MDST-12-17 | 854 | Button Assembly (Crimson) |
| 22 | TMAK-11-19 | 865 | Operation Panel Fastener |
| 23 | TMAU-12-18 | 943 | Collar — 34 x 28 x 7H |
| 24 | MDSA-23-31 | 935 | Micro Switch P163C3RU (Red) |
| 25 | MDSA-23-29 | 933 | 062U Switch Collar |
| 26 | MDSA-23-30 | 934 | 062U Switch Bezel |
1: A8 Control Lever Assembly
Operation Panel Assembly
PCK1 - LED PCB Assembly: PARTS LIST
PART NO. PCKU-24-01 PCKU-24-11 PCKU-24-12
TPP2-07-32 TPP2-07-33 CHPU-22-56 CHPU-21-62 TPP2-07-39 TPP2-07-63 PCKU-24-16 PCKU-24-17 ORDER NO. 7930 7947 7948
1012 1002
2065 7950 7949 DESCRIPTION (Reference Designations) PCK1-LED Complete PCB Assembly 74HCT138 3 TO 8 Demultiplexer LR74HC4511/TC74HC4511P BCD to 7 Segment Latch/Decoder/Driver 1S5277B Diode DAN401 Quad Cathode-Common Diode Array 100 pf. 50V Ceramic-Disc Capacitor 0.01 uF 50V Ceramic-Disc Capacitor 33uF 16V Al Electrolytic Axial Cap. Octal 1K Ohm Series Resistor Array El 12 pin Plug Connector Right Angle GL-8E040 7-Segment Visible Light Emitting Diode (US)
(U1~U4) (D1~D3) (DM1) (C7~C10) (C2~C6) (C1) (RM1) (P1) (LED1~LED4)
WIRING HARNESS AND BODY PARTS
PART NO. ORDER NO. PCKU-61-12 7932 PCKU-01-24 7931 MGSU-01-24 1107 PCKU-41-11 7933 MDSU-41-14 2367 PCKG-41-14 7934 DESCRIPTION (Reference Designations) PCK Side Decal PCK Name Plate Overlay MGS Name Plate Plexiglas (Clear) UP 36P 080 Edge Connector Harness UP 15P 062 Switch Harness UP 12P 080 Switch Harness
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
PRINTED IN U.S.A.