CATHODE RAY TOMES

Road Blasters Cockpit TM-299 1st Printing

Road Blasters (upright, rev 4) (Atari Games, 1987) · Technical Manual · 68 pages · 54 sections · original scan

Page 1

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 2

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 3

~, Road Blasters’ Operators Manual with Illustrated Parts Lists

GAMES

Page 4

© 1987 by Atari Games Corporation All rights reserved No part of this publication may be reproduced by any mechanical, photographic, or electronic process, or in the form of a phonographic recording, nor may it be stored in a retrieval system, transmitted, or otherwise copied for public or private use, without permission from the publisher. The game play, all graphic designs, this technical manual, its accompanying schematic diagrams, and the display manual are protected by the U.S. Copyright Act of 1976. This Act provides for increased penalties for violating federal copyright laws. Courts can impound infcinging articles while legal action is pending. If infringers are convicted, courts can order destruction of the infringing articles. In addition, the Act provides for payment of statutory damages of up to $250,000 in certain cases. Infringers may also have to pay costs and attorneys’ fees and face an imprisonment of up to five years. Atari Games Corporation will aggressively enforce its copyrights against any infringers. We will use all legal means to immediately halt any manufacture, distribution, or operation of a copy Of video games made by us. Anyone who purchases such copies risks forfeiting such a game,

Published by: Atari Games Corporation 675 Sycamore Drive P.O. Box 361110 Milpitas, California 95035

Printed in the U.S.A. 3R Road Blasters

Page 5

Road Blasters

Notice Regarding Non-ATARI® Parts

A WARNING A

Use of non-ATARI parts or modifications of any ATARI game circuitry may adversely affect the safety of your game, and may cause injury to you and your players.

You may void the game warranty (printed on the inside back cover of this manual) if you do any of the following: © Substitute non-ATARI parts in the game. © Modify or alter any circuits in the game by using kits or parts not supplied by Atari Games Corporation.

NOTE

This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual, may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart] of Part 15 of Federal Communications Commission (FCC) Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area or modification to this equipment is likely to cause interference in which case the user, at his own expense, will be required to take whatever measures may be required to correct the interference. If you suspect interference from an ATARI® game at your location, check the following:

  • All ground wires in the game are properly connected as shown in the game wiring diagram. © The power cord is properly plugged into a grounded three-wire outlet. © On games provided with an Electromagnetic Interference (EMI) ground plane, be sure the game printed-circuit boards (PCBs) are properly installed on the EMI Ground Plane.If you are still unable to solve the interference problem, please contact Customer Service at Atari Games Corporation. See the inside front cover of this manual for service in your area.

iii

Page 6

Road Blasters

Table of Contents

Set-Up How to Use This Manual .. Inspecting the Game . . Control and Switch Locations . Stabilizing the Sit-Down Cabinet ..... Setting the Coin and Game Options . Game Play Le

Self-Test RAM/ROM Test..........- Switch Test . . Coin Options . Game Opiions . . Statistics ....... Histograms .... . Playfield Test... Control Test . Motion Object Test. . . Motion Object Height "Test . Alphanumerics Test . . Color Test Color Purity Test. . Convergence Test Sound Test

Maintenance Preventive Maintenance . Preventive-Maintenance Intervals Removing the Control Panel oe Maintaining the RTC Steering Control . Cleaning the Coin Mechanism ..... Cleaning the Interior Components . .

Corrective Maintenance .. Removing the RTC Steering Control .... RTC Steering Control . . ede Removing the Video Display Removing the Foot Pedal Control Removing the Game PCBs . Removing the Speakers ....

Troubleshooting Troubleshooting Aids ... . Troubleshooting Technique Soldering Techniques ..... . : . : . Troubleshooting Static- Sensitive Devices . Lee beet e eee eee eee

Illustrated Parts Lists See List of [Mustrations that follows. 2-6

3-2 3-2 3-2 3-2 3-2 3-2

3-4 3-4 3-6 3-7 3-8

3-9

Road Blasters Coin Information and Game Statistics Sheet See last page of this manual.

Page 7

List of ustrations

Figure 1-1 Control and Switch Locations «0.2.2.0... eee Figure 1-2 Stabilizing the Sit-Down Cabinet ........... ts eg bere tamed

Figure 2-1 ROM Test Fails Figure 2-2 RAM Test Fails. Figure 2-3 Switch Test . Figure 2-4 Coin Options . Figure 2-5 Game Options . . Figure 2-6 Statistics . . Figure 2-7 Histograms Figure 2-8 Playfield Test... . Figure 2-9 Control Test . Figure 2-10 Motion Object Test . . Figure 2-11 Motion Object Height Test . . Figure 2-12 Alphanumerics Test .. . Figure 2-13 Color Test... ... : Figure 2-14 Color Purity Test. . Figure 2-15 Convergence Test. . Figure 2-16 Sound Test ......

Figure 3-1 Speaker, Fresnel Lens, and Video Display Shield Removal . Figure 3-2 RTC Steering Control Disassembly and Lubrication Figure 3-3 Video Display Removal . Figure 3-4 Game PCB Removal ....

Figure 4-1 Removing IC (CutPin Method) ..............0-00 0000 eee Figure 4-2 Removing IC Pins.............000. Figure 4-3 Removing Solder from Plated-Through Holes . be ane aay Come ee Figure 4-4 Removing Solder from Lead Connection Pads.............-255

Figure 5-1 Cabinet-Mounted Assemblies .............-... Figure 5-2 RTC Steering Control Assembly . . Figure 5-3 Foot Pedal Assembly......... Figure 5-4 Switching/Linear (SL) Power Supply Assembly . Figure 5-5 Coin Acceptors, Inc. Coin Door Assembly. . i Figure 5-6 Printed-Circuit Board (PCB) Mounting Hardware : Figure 5-7 Cockpit LSI Main PCB Assembly Figure 5-8 Cockpit Cartridge 5 PCB Assembly . : Figure 5-9 Audio II PCB Assembly (A043661-03 and + 05).

List of Tables

Table 1-1 Game Specifications .... . Table 2-1 Faulty ROM Locations ... . Table 2-2 Coin Option Settings . . Table 2-3 Game Option Settings .... 5-14 5-17 5-18 5-22 5-26 Road Blasters

Page 8

vi

Safety Summary

The following safety precautions apply to all game operators and service personnel. Specific warnings and cautions will be found throughout this manual where they apply.

A WARNING A

Properly Ground the Game. Players may receive an electrical shack if this game is not properly gtounded! To avoid electrical shock, do not plug in the game until it has been inspected and properly grounded. This game should only be plugged into a grounded three-wire outlet. If you have only a 2-wire outlet, we recommend you hire a licensed electrician to install a grounded outlet. Players may receive an electrical shock if the control panel is not properly grounded! After servicing any parts on the control panel, check that the grounding wire is firmly secured to the inside of the control panel. Only then should you lock up the game. AC Power Connection. Before connecting the game to the AC power source, verify that the game’s power supply is properly configured for the line voltage in your location. Disconnect Power During Repairs. To avoid electrical shock, disconnect the game from the AC power source before removing or repairing any part of the game. When removing or repairing the video display, extra precautions must be taken to avoid electical shock because high voltages may exist within the display circuitry and cathode-ray tube (CRT) even after power has been disconnected. Do not touch internal parts of the display with your hands or with metal objects! Always discharge the high voltage from the CRT before servicing this area of the game. To discharge the CRT: Attach one end of a Sarge, well-insulated, 18-gauge jumper wire to ground. Momentarily touch the free end of the grounded jumper to the CRT anode by sliding it under the anode cap. Wait two minutes and discharge the anode again. Use Only ATARI Parts. To maintain the safety integrity of your ATARI game, do not use non- ATARI parts when repairing the game. Use of non-ATARI parts or other modifications to the game circuitry may adversely affect the safety of your game, and injure you or your players. Handle the CRT With Care. If you drop the CRT and it breaks, it may implode! Shattered glass can fly six feet or more from the implosion. Use the Proper Fuses. To avoid electrical shock, use replacement fuses which are specified in the parts list for this game. Replacement fuses must match those replaced in fuse type, voltage rating, and current rating. In addition, the fuse cover must be in place during game operation.

CAUTION Properly Attach All Connectors. Make sure that the connectors on each printed-circuit board (PCB) are properly plugged in. Note that they are keyed to fit only one way. If they do not slip on easily, do not force them. A reversed connector may damage your game and void the warranty. Ensure the Proper AC Line Frequency. Video games manufactured for operation on 60 Hz line power (i.e., United States) must not be operated in countries with 50 Hz line power (i.e., Europe). The fluorescent light ballast transformer will overheat, causing a potential fire hazard if 60 Hz games are operated on power lines using 50 Hz. Check the product identification label of your game for the line frequency required. ABOUT NOTES, CAUTIONS, AND WARNINGS In all Atari publications, notes, cautions, and warnings have the following meaning:
NOTE—A highlighted piece of information.
CAUTION—Equipment and/or parts can be damaged or destroyed if instructions are not followed. You will void the warranty on Atari printed-circuit boards, parts thereon, and video displays if equipment or parts are damaged or destroyed due to failure of following instructions.
WARNING—Playets and/or technicians can be injured or killed if instructions are not followed. (The word WARNING is always surrounded by international warning symbols—triangles with exclamation marks inside of them.) Road Blasters
Page 9

Chapter 1

Set-Up

How to Use This Manual

This manual is written for game operators and service personnel, and provides information for setting up, playing, testing, and maintaining your Road Blasters™ game. The manual is divided into the following chapters:

  • Chapter 1 contains set-up and game play information.
  • Chapter 2 contains self-test procedures. © Chapter 3 contains preventive and corrective maintenance procedures.
  • Chapter 4 contains troubleshooting information. © Chapter 5 contains illustrated parts lists. Wiring and schematic diagrams for the Road Blasters game circuitry are contained in the Schematic Package Supplement (SP-299) included with your game. This chapter includes information required to set up and play your Road Blasters game. Carefully read the information in this chapter before applying power to the game.

A WARNING A

To avoid electrical shock, do not plug in the cabinet until it has been properly inspected and set up for the line voltage in your area. This cabinet should only be connected to a grounded three-wire outlet. If you have only a two-wire outlet, we recommend that you hire a licensed electrician to install a grounded outlet. Players can receive an electrical shock if the cabinet is not properly grounded. Do not touch internal parts of the display with your hands or with metal objects.

Page 10

setup

Inspecting the Game

& WARNING A Do not plug in the game until you have completed the following inspection steps. |

Please inspect your Road Blasters game carefully to ensure that the game is compiete and delivered to you in good condition. Figure 5-1 shows the locations of the component parts of the game. Table 1-1 lists space, power, and environmental requirements. Inspect the factory-assembled game as follows: 1, Examine the exterior of the cabinet for dents, chips, or broken parts

  • Unlock and open the rear access panel. Unlock and open the coin doors. Inspect the interior of the cabinet as follows: a. Ensure that all plug-in connectors (on the cabinet harnesses) are firmly plugged in. Do not force connectors together, The connectors are keyed so they only fit in the proper orientation. A reversed edge connector can damage 4 printed-circuit board (PCB) and will void your warranty’ b. Ensure that ali plug-in integrated circuits on cach PCB are firmly plugged into their sockets. ¢. Inspect the power cord for any cuts or dents in the insulation. d. Inspect the power supply. Make sure that the correct fuses are installed. Check that the harness is plugged in correctly and that the fuse block cover is mounted in place. Check that the green ground wires arc connected. e. Inspect other major sub-assemblies, such as the video display, printed-circuit boards (PCBs), and speakers. Make sure that they are mounted securely and that the ground wires are connected.

Table 1-1 Game Specifications

Characteristic Specification

Power Consumption 300 V-A, 239 W RMS Temperature +5° to 438°C (+37° to + 100° F) Humidity Not to exceed 95% relative Line Voltage 102 to 132 VAC (U.S. games) 198 to 264 VAC (Irish gantes) Width 29.5 in. (75 cm) Length 84 in. (213 em) Height 55.25 in. (135 cm) Road Blasters

Control and Switch Locations

Power On/Off Switch The power on/off switch is located in the lower corner of the right side panel of the cabinet. (See Figure 1-1.)

Volume Control The volume control is located on the Audio II PCB on the inside of the rear access panel. (See Figure 1-1.) The volume control adjusts the level of sound produced by the game.

Coin Counter The coin counter is located on the shelf inside the upper coin door. The coin counter records the number of coins deposited.

Self-Test Switch The self-test switch is located on the shelfinside the upper coin door. (Sce Figure 1-1.) The self-test switch selects the Self-Test Mode to check game operation. Refer to Chapter 2 fora complete description of self-test operation.

Stabilizing the Sit-Down

Cabinet

The sit-down cabinet should be immobilized so that players Cannot roll the cabinet around. To stabilize the cabiift up the game from one side. Place a two-inch thick of wood, book, or other object under the edge of the raised cabinet. Partially unscrew the adjustable glides until they extend below the casters. Then, lower the cabinet and lift the other side. Partially unscrew the adjustable glides until they extend below the casters, Lower the cabinet. (See Figure 1-2.)

Setting the Coin and Game

Option Settings

The Road Blasters coin and game options are set in the Self-Test Mode Refer to Chapter 2 for the recommended settings and the procedure for setting the options.

Game Play

This section of the manual describes the theme of the Road Blasters game, the operating modes, and the game play features.

Introduction Road Blasters is an action-packed battle game where the player drives a high-performance armored car. Road

Page 11

Road Blasters

2nd Coin Counter (European Games Only)

Auxiliary Coin Switches Coin Counter

Self-Test Switch Set-tip

Rear Door

Volume Control

On/Off Switch (Inside View)

Figure 1-1 Control and Switch Locations

Blasters features a new return-to-center (RTC) steering control with fire buttons to highlight the realistic driving perspective and added action element of laser artillery and unique special weapons. Atari Games has designed Road Blasters in cooperation with Matchbox Toys, a company famous for its authentically detailed collectible die-cast cars. Road Blasters is a new Matchbox line of futuristic action/adventure vehicles.

Attract Mode The Attract Mode begins when the game is powered up or after exiting the Play or Self-Test Modes. The Attract Mode ends when coins or tokens are inserted and the gas pedal is pressed. The Attract Mode continuously cycles through the following displays: © Road Blasters title screen

  • Game play demonstration © Screen displaying The Enemy and their respective point values © High score table © Contest information (U.S. and Canada only)

Unique Features to Attract Players

¢ Tie-in with the Matchbox Road Blasters line of action/ adventure vehicles. Matchbox Toys will support its Road Blasters line with television advertising in the spring and fail of 1987, in addition to retail promotions and an ambitious public relations campaign. As an amusement game Operator owning a Road Blasters video game, you will profit from the public awareness created by Matchbox Toys.

A special player contest (in the U.S. and Canada only) to promote increased play on the game. Players who complete rally 50 are asked to enter their name and obtain a secret code. When mailed to Atari Games, this secret code entitles the player to a specially designed Road Blasters T-shirt. Detailed rules are on the marquee packaged with your Road Blasters game.

¢ The Road Blasters unique high-tech cockpit cabinet wiil be an attention-grabber in ail locations.

Page 12

setUp

Caster

Adjustable ll

Figure 1-2 Stabilizing the Sit-Down Cabinet

  • Realistic graphic quality is highlighted by the unique fresnel lens that overlays the display and magnifies the screen graphics, simulating a 25-inch monitor.

Play Mode Road Blasters is the Ultimate Race of the Future—-being part road race and part combat-zone survival exercise. The roadway leads the player through a progression of countries, alternating checkpoints, and rally points. Checkpoints are mid-point goals that award additional fuel as the player races past. Rally points are similar to finish lines in ordinary race games because they indicate the completion ofa race section. In the case of Road Blasters, a scroll-up video display evaluates player performance at each rally point. The game ends when the players run out of fuel by driving too slow, or crashing too often. Player controls consist of an RTC steering control with triggers and thumb firing buttons, and a gas pedal. The triggers contro! the laser gun; the thumb buttons ignite the special weapons. Players can tag the green and red fuel globes placed along the roadway to obtain more fuel. As a reward, their cars are also refueled when they reach each checkpoint and rally point. Four unique computer-controlled opponent vehicles challenge players: sleek, fast Stingers; heavily armored Command cars; evasive and unpredictable Rat Jeeps; and quick, darting Cycles. These vehicles combine forces to try to prevent the players from reaching the next rally point. In addition, there are mines in the road, gun turrets Road Blasters

of the side of the road shooting at the players, spikers thrown by opponent vehicies, and other obstacles to be avoided. The player can dock with the special attribute pack dropped by the support jet to acquire special weapons. Special weapons include: Cruise Missiles that destroy everything in the path of the player that is visible on the screen; Nitro Injectors that boost the speed of players’ cars; U.Z. Cannons that rapid-fire; and Electro Shields that protect players’ cars from shots, collisions, mines, and spikers.

High Score Mode

Upon completing a game and if players are among the top ten scorers recorded on the game, they have 17 seconds to enter their first initial and another 17 seconds for the next initial, until all have been entered. Players select their initials by pressing the thumb buttons or the triggers Players can correct their initials by selecting the arrow that points to the left and pressing the gas pedal, then repeating the procedure for entering their correct initials. Toencourage high score competitiveness among players, your Road Blasters game automatically resets the high score table to the default list of players’ initials and scores. During normal use (when the game is turned off at closing time), the top four scores are reset if more than 200 sequential games have elapsed and no players have entered their initials as one of the top four scores. This interval is about once a week; the reset occurs during power-up. Scores 5 through 10 are reset daily during power-up.

Maximizing Earnings

Operator options on this game have been kept very simpie. You should thoroughly read Chapter 2, Self-Test, for the Coin Options, Game Options, Histograms, and Statistics screens so that you can effectively use the available options. Use the Self-Test screens showing Statistics and Histograms to evaluate game data, and the Game Options screen to make adjustments. (Refer also to the Self-Test chapter for more information on setting options.) The key to maximum earnings is striking a midpoint on game times. Game times must be short enough so that player turnover is high. Conversely, game times must be long enough to give players a good value and ensure repeat play. (Repeat play is crucial to longevity.) The Road Blasters software gives the operator the flexibility to tune game difficulty and enough statistics to intelligently make adjustments. Ii collections seem low or are dropping off, check all player controls and coin mechanisms for proper operation. If earnings seem low, the game is technically sound and the average game time per quarter is under 110 seconds,

Page 13

Road Blasters

try changing the game difficulty option to an easier setting. This change will give players more game time relative to their score. If the average game time per quarter is over 180 seconds, first try changing the game difficulty to a harder setting. If the average game time per quarter is still over 180 seconds after a few weeks, try an even harder setting.

| NOTE

Be sure to keep the factory default at no if you wish to try other than factory-recommended settings. SecUp

After changing the game difficulty settings. it is a good idea to reset the game statistics. The coin information and game statistics should be cleared in self-test by pressing the trigger button; this resets the average game time statistic. In addition, the histograms should be cleared by pressing the foot pedal while displaying the level 5 Histogram screen.

1-5

Page 14

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 15

Chapter 2

Self-Test

The Road Blasters™ game tests itself and provides visual and audible indications of the condition of the game circuitry. Self-test information is displayed on the screen and through the sound system. No additional equipment is required. We suggest that you perform a self-test when you first set up the game, each time you collect the money, or when you suspect game failure. Coin and game options are selected in the Self‘Test Mode. After the self-test switch is turned on, 16 self-test screens provide information pertaining to the game circuits. Refer to Chapter 1 for the location of the self-test switch. When the self-test switch is turned on, and the power is then turned on, the game enters the full Self-Test Mode. If the self-test switch is turned on while pressing the trigger button, the game enters a shorter Self-Test Mode. The following self-test screens are arranged in the sequence in which they occur after the self-test switch is first turned on, After the Sound Test, the sequence starts over with the Switch Test. Turning the self-test switch off at any time during the Self‘Test Mode causes the game to return to the Attract Mode.

NOTE During any of the self-tests, press the thumb button on the RTC (return-to-center) steering control to advance to the next screen.
Page 16

Self-Test

RAM/ROM Test

The RAM/ROM Test screens are shown in Figures 2-1 and 2-2. These tests provide a visual check of the game RAM, ROM, and associated circuitry. If the RAM and ROM test passes, the display advances to the Switch Test. The RAM/ROM Test is divided into two sections. The condition of the RAM circuitry is displayed in the bottom half of the screen and, after about an eight-second delay, the condition of the ROM circuitry is displayed in the top half of the screen. An error message indicates that the RAM, ROM, or associated circuitry may be faulty. If the ROM test fails, an error message appears in the top half of the screen as shown in Figure 2-1. Refer to Table 2-1 for the faulty ROM locations. If the upper or lower main memory ROM circuits on the Main PCB fail, an Upper or Lower Main ROM Error message appears at the top of the screen. Press the thumb button to obtain any RAM or ROM error message(s) from

Figure 2-1 ROM Test Fails

Figure 2-2 RAM Test Fails Road Blasters,

Table 2-1 Faulty ROM Locations

Location on Cartridge 5 Error Message PCB Assy

ROM at 10000 errorU=7PL=8P
ROM at 20000 errorU=7RL=8&R

ROM at 30000 error u=7S 8S

ROM at 50000 errorU=7LL=8L
ROM at 60000 errorU=7ML=8M
ROM at 70000 errorU=I7NL=8N

Bank switch error

Bwitoh test Bossa, npere's ange Pfom Oto t *

2 2.

Beess THUMB BUTTON ror hex t Voce

Figure 2-3 Switch Test

the Cartridge PCB RAM or ROM circuits. Press the thumb button again. If the bank switch ROM circuits on the Cartridge PCB are faulty, the message Bank Switch Error will appear. 1f the RAM test fails, an error message appears as shown in Figure 2-2. Refer to the memory maps and schematic diagrams in the Schematic Package Supplement (SP-299) to determine the location of the faulty RAM circuit.

Repair the faulty RAM or ROM circuit or press the thumb button to obtain the Switch Test.

Switch Test

The Switch Test screen is shown in Figure 2-3. This test indicates the condition of the trigger pushbutton switch. Press the trigger button, and note that the first number changes toa 1.

Press the thumb button to obtain the next screen.

Page 17

Road Blasters.

NOTE For all subsequent tests in the self-test, the following summarizes the functions of the various switches:
  • The thumb button sequences to the next test.
  • The foot pedal has an action function. For example, in the convergence test pressing the pedal changes the grid lines from white to violet; in the sound test, the audio starts sounding. © The RTC steering control left-to-right movement selects choices. (Right/left arrows are displayed in the upper right corner on the screen.) © The trigger switch, if pressed, changes the RTC steering control to show up/down movement on the screen. (Up/down arrows are displayed in the upper right corner of the screen.)

Coin Options

The Coin Options screen is shown in Figure 2-4. This screen indicates the current coin option settings and is used to change these settings. Refer to Table 2-2 for the available and recommended settings.

NOTE If you wish to try other than factory-recommended options, leave the Restore Factory Options setting at no.

Coin Options CUP nue Right Meoh Wurtivls Left Meoh Multipiie Genus Adder

Fe ty OER, iginal setting to save this setting and exit

Figure 2-4 Coin Options Self-Test

Table 2-2 Coin Option Settings

Option Name Available Settings

1 Coin 1 Credit <4 2 Coins 1 Credit 3 Coins 1 Credit 4 Coins 1 Credit Credit Mode

1 Coin Counts as 1 Coin <¢ 1 Coin Counts as 4 Coins 1 Coin Counts as 5 Coins 1 Coin Counts as 6 Coins Right Mech Multiplier

1 Coin Counts as 1 Coin <4 1 Coin Counts as 2 Coins Left Mech Multiplier

No Bonus Adder <¢ 2 Coins Give 1 Extra Coin 4 Coins Give 1 Extra Coin 4 Coins 2 Extra Coins 5 Coins Give 1 Extra Coin 3 Coins Give 1 Extra Coin Free Play Bonus Adder

<¢ Manufacturer's recommended settings

Coin Mode should be highlighted. Move the RTC steering control right or left, and note that the coin mode values change. Select the desired value. Move the RTC steering control to the right (while the trigger switch is pressed); this moves the box to Right Mech Multiplier, Move the RTC steering control right or left (without pressing the wigger switches) to cycle through all the available multiplier values. Select the desired value. Repeat this procedure for the remaining options. If you wish to cancel the option changes and restore the original settings, press the foot pedal. Press the thumb button to set the selected coin options and to obtain the next screen.

Game Options The Game Options screen is shown in Figure 2-5. This screen indicates the current game option settings and is used to reset the high score table and to change the game option settings. Refer to Table 2-3 for the available options and the default (recommended) settings. Note that the recommended settings are highlighted in green. Move the RTC steering control right or left and note that the settings for the option in the shaded block change. Select the desired value. Press the trigger switch and simultaneously move the RTC steering control lefvright to move the desired option into the shaded block. Move the RTC steering control right or left (without pressing the trigger switch) to cycle through all the available game option settings and select the desired value. Repeat this procedure for the remaining options.

Page 18

Self-Test

Geme Options , ncneel 5 ICULTY. CREDITS TO.START / CREDITS NYYSER OF CONT INUATIONS PUTOMATIC HIGH SCORE RESEY AFTER 200 P

MUSIC IN ATTRACT, MODE vw nore ow Foot iginol setting to save a setting and exit

Figure 2-5 Game Options

erer Boel Ave. Game Time: 96 seconds.

Press Foot to Sieee a tatistion Press, BuTToON * for Histograms

Figure 2-6 Statistics

If you want to cancel the option changes and restore the original settings, press the foot pedal. Press the thumb button to set the selected game options and to obtain the next screen.

Statistics

The Statistics screen is shown in Figure 2-6. This screen provides a visual check of the current game statistics. The statistics information is accumulated either from the first time the game was turned on or from the last time the statistics were reset. To reset the statistics information, press the trigger button The following information appears on the Statistics screen:

© Aux coins not used in the Road Blasters game.

© Left coins shows the number of coins deposited in the left coin mechanism.

2-4 Road Blasters

© Right coins shows the number of coins deposited in the right coin mechanism 1 plyr Games shows the number of 1-player games.

Mins played shows the total time, in minutes, of all the games played. Mins pwr up shows the total time, in minutes, that the game has been turned on.

  • Aux, cntr i shows the highest rally achieved. Aux. cntr 2 shows the total number of times the add-acoin was used

Aux. cntr 3 shows the number of games without anew high-score entry. Error count shows the number of EEPROM errors that were detected. Replace the EEPROM at location 15F on the Main PCB if the errors detected exceed approximately 75 per week

Avg. Game Time shows the average game time per play in seconds, including add-a-coin continuation games.

Table 2-3. Game Option Settings

Option Name Available Settings

Clear high score table No< Yes:

Game difficulty Easy Medium <4 Hard Difficult

Credits to start/credits to 1/1 continue 2/1

Number of 2 continuations 3

Unlimited number <4

Automatic high score re- Yes <4 set after 200 games No

Music in attrac! mode Yes <4 No

Yes <4 (U.S. and Canada only) No (Europe only) Rally 50 contest enabled

Demo/play mode Playable game mode <4 Demonstration mode (players cannot crash)

Restore factory options Yes No <4

“¢ Manufacturer's recommended settings

Page 19

Road Blasters

Press the thumb button to obtain the next screen.

Histograms There are five Histogram screens. One screen is shown in Figure 2-7. The screens are selected by pressing the thumb button. Each screen shows the lengths of the games from 0 to 540 or more seconds and the total number of players. The high score for each level is also displayed. The Histograms for Levels 1 through 3 show the players’ wave selections (choosing from Rookie, Veteran, or Expert). The Histogram for Level 4 shows the number of games that ended on the original level of the game continuation feature. The Histogram for Level 5 shows the number of games that ended ona higher level after a game continuation.

The game times information is accumulated either from the first time the game was turned on or from the last time the game times were reset. To reset the Histograms, press the foot pedal while displaying the Histogram for the Level 5 screen.

Press the thumb button to obtain the next screen.

Playfield Test

The Playfield Test screen is shown in Figure 2-8. This screen indicates the condition of some of the graphics ROM, and the vertical and horizontal playfield scrolling registers. Move the RTC steering control to the left, and the playfield should slowly scroll to the left. Move the RTC steering control right, and the playfield should scroll right. Pressing the trigger button causes the RTC steering control to scroll the playfield up/down when the RTC control is moved left/right.

Histesren for level 5

High score for level: 784640 Prestclear ait hixtosrams Pegss THUNE BUTTON or next screen

Figure 2-7 Histograms Self-Test

he tan

Control Test ring: 144 90 edal: O36 34

Figure 2-9 Control Test

Press the thumb button to obtain the next screen.

Control Test The Control Test screen is shown in Figure 2-9. This screen indicates the condition of the controls, graphics ROMs, and motion object circuitry. Moving the RTC steering control to the left and right will change the displayed value next to the word STEERING: (the left number is in decimal, the right one is in hexadecimal). Look for consistent readings (within +2) when you move the control to its left and right limits. The FOOT PEDAL: message also displays decimal (left) and hexadecimal (right) values. Look for a difference of at least 64 between the fully pressed and fully upright positions of the foot pedal. These values should increase as the pedal is pressed. Also note that the player's car should be displayed in the center pointing ahead, as in game play. Another vehicle is

Page 20

Self-Test

displayed (initially a stinger) at the top of the roadway in the left lane. Moving the RTC steering control selects a different opponent; moving the RTC steering control to the left or right steps that opponent through the next lane on the left or right. Finally, pressing the foot pedal moves the vehicle down the screen towards the botiom, Eventually the opponents will disappear as they move outside the display window.

Motion Object Test The Motion Object Test indicates the condition of the motion-object buffer circuit. The seven groups of eight motion objects should be identical and eight pixels high. Press the trigger button to select one of the 56 motion objects. RTC left/right movement moves an object left/ tight. The object should be invisible about half the distance of its travel (for about five seconds). Pressing the trigger switch causes the RTC steering control left/right movement to move the object up/down. (Figure 2-10 shows the screen after some motion objects have been moved.) Press the thumb button to obtain the next screen.

Motion Object Height Test

The Motion Object Height Test indicates the condition of the motion object/playfield graphic address generator circuit. Each successive column of motion objects should be eight pixels taller than the last. The top eight pixels of all the columns should be the same. The top 16 pixels of all the columns that are at least 16 pixels high should be the same. Each column should add a new 8 x 8 pixel stamp picture to the bottom and slide the old picture up by eight pixels. The motion objects can be moved by following

Motion Object Tent Perencter Butter °

BERR PES UTION

Figure 2-10 Motion Object Test

2-6 Road Blasters

Motion Object Heisht Test

<200 pec | Brana ey Soa sical eel for Next Tes: i

Figure 2-12 Alphanumerics Test

the same procedure as in the Motion Object Height Test. (Figure 2-11 shows the screen after some motion objects have been moved.) Press the thumb button to obtain the next screen.

Alphanumerics Test The Alphanumerics Test screen is shown in Figure 2-12. This test indicates the condition of the alphanumerics circuit. Press the thumb button to obtain the next screen.

Color Test The Color Test screen is shown in Figure 2-13, This test indicates the condition of the dispiay color circuits. There should be eight vertical grey-scale bars and three groups of eight horizontal bars with shades of red, green, and blue. The brightest bars should be on the left, and the

Page 21

Road Blasters

Figure 2-14 Color Purity Test

darkest (black) bars should be on the right. A bright white frame should surround the screen: this frame will help to identify the darkest color band. If the display characteristics are not correct, refer to the display manual for the color-gun adjustment procedure or to determine the possible cause of failure. Press the thumb button to obtain the next screen.

Color Purity Test The Color Purity Test consists of five color displays that indicate the condition of the display color-purity circuits. The first display to appear should be a red screen with the word RED displayed at the bottom of the screen.. Press the foot pedal and the next display to appear should be green with the word GREEN displayed at the bottom of the screen (see Figure 2-14). Press the foot pedal to obtain a blue, white, and finally a grey screen. After the grey screen the software repeats the cycle, beginning with the red screen. Self-Test

If the display characteristics are not correct, refer to the video display manual for the color-purity adjustment procedure or the possible cause of failure. Press the thumb button to obtain the next screen.

Convergence Test The Convergence Test screen is shown in Figure 2-15. This test indicates the condition of the display size, centering, linearity, and convergence. The grid pattern should be white

Press the foot pedal, and the pattern should turn violet. Repeated pressing of the foot pedal should cause the screen to alternate between violet and white. Check the grid pattern for the following characteristics (the violet and white patterns are used to adjust the display convergence): © The four corners of the frame around the grid pattern should touch all four corners of the screen.

  • Grid lines should exhibit no pincushioning or barreling, and the lines should be straight within 3 mm.

Violet and white pattern convergence should be within 2 mm.

If the display characteristics are not within these limits, refer to the display manual for the linearity and convergence adjustment procedures or to determine the possible cause of failure.

Move the RTC steering control left/right, and the pattern should slowly move left/right. Moving the RTC steering control left or right with the trigger switch depressed should cause the pattern to scroll up or down.

Press the thumb button to obtain the next screen.

iH Hi

Page 22

Self-Test

Sound Test The Sound Test screen is shown in Figure 2-16. This test indicates the condition of the coin mechanisms, and the music and sound-effects circuits. The sound microprocessor is reset at the beginning of this test; the reset can take several seconds. If the sound-microprocessor reset fails, the message SOUND PROCES- SOR NOT RESPONDING should flash near the top of the screen. Move the RTC steering control left with the trigger switch pressed to sequence forward through the

Sound Test

Seund CPy ROMS Error | Bieber’ e"deungs ge Boone cho Status tovg GIEERING WHEEL ‘ect Sound ges, FOOT PEDAL 20° Steee So in Rea dain bre HA Neer ue out

Sound CPU RAM 4 Error Press THUMB BUTTON ‘Next

Figure 2-16 Sound Test Road Blasters

sounds; move the RTC steering control right with the trigger switch pressed to sequence backwards. Press the foot pedal to start the selected sound. The Sound Test provides the following sound information: © Current Coin Value consists of three zeros. AS coins are deposited in each of the coin mechanisms, the second and third zero should change to a / as the coin. switch is held down and should change back to zero when the coin switch is released.

  • Number of Sounds indicates the number of sounds used in the Road Blasters game. Sound CPU Status indicates the condition of the sound microprocessor. If the sound microprocessor is good, the word Good should appear. If the sound microprocessor is faulty, the message Sound CPU ROM 1, ROM 2, or ROM 3 Error appears at the top of the screen. (ROM 1 is at location 7/8C/D on the Cartridge 5 PCB Assembly; ROM 2 and ROM 3 is at location 7/8D on the same PCB.) Music Chip Test consists of eight tones in a major scale that alternate between sound channels (16 tones in all). Effects Chip Test consists of four tones ina major chord. that come from both sound channels simultaneously. Speech Chip Test consists of a synthesized voice repeating the message ‘speech chip test.”’ Press the thumb button to obtain the first screen (the RAM/ROM Test).
Page 23

Chapter 3

Maintenance

This chapter includes preventive and corrective maintenance procedures for the Road Blasters” game components that are subject to the most use. To assure maximum trouble-free operation from this game, we recommend that preventive maintenance be performed as described in this chapter. Removal, disassembly, reassembly, and replacement procedures are provided for components that might require corrective maintenance. Appropriate references are provided to Chapter 5, Iliustrated Parts Lists, to help locate the parts of this game that are mentioned, but not illustrated, in the maintenance procedures.

Page 24

Maintenance Road Blasters

Preventive Maintenance

Preventive maintenance includes cleaning, lubricating, and tightening hardware, How often preventive maintenance is performed depends upon the game environment and frequency of play. We recommend that preventive maintenance be performed at the intervals specified.

A WARNING A

To avoid possible electrical shock, turn off the game before performing any maintenance procedures.

Preventive-Maintenance Intervals

The preventive-maintenance intervals are the recommended minimum requirements for the components listed.

  • RTC Steering Control Inspect weekly, lubricate, and tighten hardware at least every three months. Also, inspect the handle microswitches weekly. © Foot Pedal Lubricate and tighten hardware at least every three months.
  • Coin Mechanism Inspect whenever coins are collected. Clean at least every three months.
  • Interior Components Clean at least every six months.

Removing the Control Panel

Perform the folowing procedure to remove/replace the control panel. (See Figure 3-1,)

  • Unlock and open the rear door.
  • Use a Phillips screwdriver to remove the four screws holding the speakers and grilies to the contro! panel. Also remove the speaker wires.
  • Use a 5/32-inch Allen wrench to remove the four screws holding the RTC steering control to the control panel. Carefully guide the RTC steering control through the hole in the control panel. a
  • Disconnect the RTC steering control harness comnector. 6, Use a ¥-inch Allen wrench to remove the ten screws holding the control panel to the cabinet. ) . Replace the control panel in the reverse order of removal. Be sure that the RTC harness wires do not interfere with the gears when the RTC steering control is installed.

Maintaining the RTC Steering Control

Preventive maintenance on the RTC steering control consists of: © Inspecting the RTC steering control housing for excessive wear or dirt. Checking the operation of all four handle microswitches. Inspecting the Optical Coupler PCB Assembly for damage and contamination. © Lubricating the bronze bearings attached to the control base weldment. © Replacing or tightening the securing hardware if necessary. Perform the following procedure to lubricate and tighten the RTC steering control. (See Figure 3-2.)

  • Remove the control panel as previously described.
  • Apply a film of light oil (Atari part no, 107013-001) to the inside and top surfaces of both bronze bearings attached to the inside ends of the control base weldment
  • Use a 5/32-inch Allen wrench to tighten the buttonhead screws holding the RTC steering control to the control panel.

Cleaning the Coin Mechanism

Use a soft-bristled brush to remove loose dust or foreign material from the coin mechanism. A toothbrush can be used to remove any stubborn build-up of residue in the coin path. After cleaning the coin mechanism, blow out all of the dust with compressed air.

Cleaning the Interior Components Perform the following procedure to clean the components inside the cabinet.

A& WARNING A Turn off the game power, but do not unplug the power cord before cleaning inside the cabinet The power cord provides a ground path for stray static voltages that can be present on the cleaning _ tools.

Page 25

Road Blasters

Control Panel ' Visor (does not need to be removed if you are removing the control panel)

Speaker Harness Assy

Fresnel Lens

Display Shield

RTC Steering Control Hamess Assy Maintenance

RTC Steering Control

Figure 3-1 Speaker, Fresnel Lens, and Video Display Shield Removal

  • Unlock and open the rear access door.
  • Discharge the high-voltage from the cathode-ray tube (CRT) before proceeding. The display assembly contains a circuit for discharging the high voltage to ground when power is removed. However, to make certain, always discharge the display as follows. a. Attach one end of a large, well-insulated, 18-gauge jumper wire to ground. b. Momentarily touch the free end of the grounded jumper to the CRT anode by sliding it under the anode cap.

c. Wait two minutes and repeat part b.

CAUTION

Be extremely careful when cleaning the electrical components inside the cabinet. Avoid touching the electrical components with any solid object other than the soft bristles of the vacuum attachment or paint brush.

. Use a vacuum cleaner with a soft long-bristled brush attachment or use a soft-bristled paint brush to remove loose dirt and dust accumulated on the inside of the cabinet. Be sure to clean the electrical components thoroughly (power supplies, PCB assemblies, display, etc.).

Page 26

Maintenance Road Blasters

Corrective Maintenance

Corrective maintenance consists of removal, disassembly, Removin the RTC Steering reassembly, and replacement of game components. The Ss following procedures are provided for components that Control might require corrective maintenance. Perform the following procedure to remove/replace the RTC steering control. (See Figure 3-2.)

  • Unlock and open the rear door on the front of the cabinet.

Screw Torque Specifications Table

Seating Torque Ref. No. Screw Size Inch-Lbs. 043929-01

Steering Head®2-56gat
042635-02®4.401243
Lett: Hand Handle@6:322825
®8.323245
042636-02®10-326425

Left-Hand Handle Cover 75-07010 177010-241 175002004 Washer ggozao.01 Hex Nut lex Nut Stop Bumper 79 agag Screw (3 each) © a 160026-001 Switch 73-20807 Roll Pin 040303-01 Trigger 042636-01 Right-Hand Handle Cover

4 042635-01 RightHand Handle, 178203-001 Cap 176022-3606 042044-01 043930-01 72-1206F

CoverOscooeloButtonScrew @ each) ®

176035-1820 @Screw (4 each) eee 160026-001 Soren @) jushing Switch 73-21208 043950-01 040252-01 Roll Pin Conical Spring Compression Spring 040473-01 Jurnper Wire

Figure 3-2. RTC Steering Control Disassembly and Lubrication

Page 27

Road Blasters Maintenance

i

a . Replace the RTC steering control in the reverse order 040235-01 ‘Spur Gear with Hub A043942-01 175002-001 176022-3604 Harness Assy Washer Screw @ 178012-001 -750 Diameter Retaining Ring

4 107013-001 Lubricant 106007-001 Penetrating Adhesive 040237-01 72-8406 ‘Anchor Nut Screw@

£178027-001 Lubricant 040239-01 k ‘ 4 75-0148 Spring K ee Washer 178101-002 043928-01 ‘Spur Gear Base 044023-02, or 044023-01 Spacer 040240-01 044024-01 Stop Bumper Encoder Disc

044022-01 040241-01 Encoder Shatt ‘Spacer Bearing 72-CT604 Screw @

A043937-01 Coupler PCB Assy

178118-001 Sleeve Bearing

178097-001 040240-01 175002-004 Bearing with Washer/Nut Stop Bumper Lala 040238-01 175009-170 Anchor Pin @ 178012-003 Washer ¥,, Diameter Retaining Ring 177010-241 Hex Nut

Figure 3-2 RTC Steering Control Disassembly and Lubrication, Continued

. Use a 5/32-inch Allen wrench to remove the four buttonhead screws holding the RTC steering control to the control panel. . Carefully guide the RTC steering control through the NOTE hole in the control panel. Certain corrective maintenance procedures can . be performed with the RTC steering control at- . Disconnect the RTC steering control harness connec- tached to the conirol panel. However, for contor inside the cabinet. venience and to avoid damaging the control panel, we recommend that the RTC steering control be removed from the control panel before of removal. Be sure to reconnect the control harness | a any maintenance or repair is performed. connector and the Coupler PCB Assembly harness connector. Also be sure that the RTC harness wires do not interfere with the gears when the control is installed.

Page 28

Maintenance

RTC Steering Control

The following corrective maintenance procedures apply to the RTC steering control. The RTC steering control consists of the handle assembly and the steering assembly.

Removing the Handles Perform the following procedure to remove the handles from the handle assembly. (See Figure 3-1.) 1. Use a 7/64-inch hex driver to remove the two cap screws holding the cover on each handle. Be careful when removing the covers that the trigger and pushbutton springs do not fall free off the handles. . Unsolder the three harness wires from the trigger and push-button microswitches inside each handle. . Use a 9/64-inch hex driver to loosen and remove the two Cap screws that secure the brace and cover. . Cut the tie wrap holding the harness, then gently pull the harness out of the shaft. . Use a 7/64-inch hex driver to remove the two cap screws that hold each handle to the shaft. . Use a ¥,-inch punch and gently drive the two roll pins from the shaft.

. Gently slide the handles from the shaft. . Reassemble the handle in the reverse order of removal.

Disassembling the Handle Assembly

Perform the following procedure to disassemble the handle assembly. (See Figure 3-2.)

NOTE Removing the handle assembly from the steering assembly is not necessary to perform the following disassembly procedure. However, refer to Disassembling the Steering Assembly later in this chapter for the procedure describing how to separate the two assemblies.

. Use a 7/64-inch hex driver to remove the two cap screws from each handle assembly cover. . Remove the handles as previously described. . Replace the handle assembly in the reverse order of removal. Be sure to install a new tie wrap to hold the harness.

Disassembling the Steering Assembly

Perform the following procedure to disassemble the steering assembly. (See Figure 3-2.)

3-6 Road Blasters

. Remove the handle covers as described previously. Be careful when opening the handles that the pushbutton and trigger springs do not fall out. . Unsolder the three harness wires from the handle push-button and trigger microswitches. . Remove the green ground wire from the ground clip on the base, and the Optical Coupler PCB harness connector.

. Use a hex driver to remove the two screws holding the Optical Coupler PCB Assembly to the base. . Use a 3/32-inch hex driver to remove the cap screw holding the encoder disc. Remove the retaining ring, two washers, encoder disc, encoder spacer, and small gear.

A WARNING A

Shield your face and eyes when prying the retainer from the shaft because the retainer can fly loose at a high speed. Cover the retainer with a rag or any material that can trap the retainer.

10.

11.

12. . Use a 7/64-inch hex driver to remove the cap screw holding the large spur gear and hub to the shaft. . Use a slotted screwdriver (or an appropriate tool) to remove the retainer from the shaft.

Use a %¢-inch wrench to remove the anchor nut on the end of the anchor pin. (The anchor nut holds the hook ends of the torsion-steering springs.) . Use a 9/64-inch hex driver to remove the two screws holding the cover to the steering head. Cut the tie wrap holding the harness, then gently pull the harness out of the shaft.

Gently pull the steering assembly from the handle assembly. Make sure the harness wires are free to slide out of the handle-assembly shaft. Use a 5/32-inch hex driver and %-inch combination wrench to remove the two bumpers from the frame.

NOTE With the steering control disassembled, lubricate the bronze bearing surfaces, and the torsion springs. Also, apply penetrating adhesive inside the anchor nut hole after assembly. Refer to Maintaining the RTC Steering Control earlier in this chapter for further information.

13. Reassemble the steering assembly in the reverse order of removal. Be sure that all necessary screws have

Page 29

Road Blasters

been tightened according to the Screw Torque Specifications Table. (See Figure 3-2.)

Installing the Harness Assembly

Perform the following procedure to install the harness assembly to che RTC steering conirol. (See Figure 3-2.) 1, If necessary, remove the handle covers as described under Removing the Handles.

  • Guide the harness wires into the spur-gear end of the hollow steering-assembly shaft. The wire routing on both microswitches should be as follows: C = Common, should be the black wire. The black wire can go to either C (common) switch tab as long as there is a jumper wire. NO = Normaily open (Thumb Button), should be the red wire. NO = Normally open (Trigger Button), should be the white wire.
NOTE The tab locations are identical on both microswitches. However, because one microswitch is upside down, the markings are not visible.
  • Route and solder the wires to the microswitches. Note that either wire bundle can go to either handle.
  • Install the wire tie, optical coupler PCB connector, and the ground clip. Make sure the wires do not interfere with the gears when the steering control is mounted.

Removing the Video Display

Perform the following procedure to remove/replace the video display. (See Figure 3-3.)

  • Turn the game power off and wait two minutes. Unplug the power cord.
  • Unlock and open the rear door. Maintenance

A WARNING A

High Voltage The video display contains potentially lethal high voltages. To avoid injury, do not attempt to service this display until you observe all precautions necessary for working on high-voltage equipment X-Radiation The video display has been designed to minimize X-radiation. However, to avoid possible exposure to soft X-radiation, never modify the highvoltage circuitry. Implosion Hazard The cathode-ray tube may implode if struck or dropped. Shattered glass may cause injury within a Gfoot radius. Use care when handling the display.

  • Discharge the high-voltage from the cathode-ray tube (CRT) before proceeding. The display assembly contains a circuit for discharging the high voltage to ground when power is removed. However, to make certain, always discharge the display as follows. a. Attach one end of a large, well-insulated, 18-gauge jumper wire to ground. b. Momentarily touch the free end of the grounded jumper to the CRT anode by sliding it under the anode cap.

c. Wait cwo minutes and repeat part b.

  • From the back of the cabinet, disconnect all the display harness connectors. Remove the ground strap from the display chassis. 5, Use a %¢-inch nut driver to remove the two hex head screws and washers from the upper corners of the video display chassis.
  • Also use a {,-inch nut driver to remove the two hex head screws, washers, and carriage bolts from the bottom corners of the video display chassis.
  • Carefully slide the display out through the rear of the cabinet.
  • Replace the video display in the reverse order of removal.
NOTE Whenever the cathode-ray tube is replaced, readjust the brightness, purity, and convergence. as described in the display manual.
Page 30

Maintenance

Video Display

Video Display Chassis

Display Harness Assy Carriage Bolt Road Blasters

Figure 3-3 Video Display Removal

Removing the Foot Pedal

Control

Perform the following procedure to remove/replace the foot pedal control.

  • Disconnect the foot pedal harness connector from the main harness assembly located inside the cabinet. . Use a 5/32-inch Allen wrench to remove the four screws and washers holding the foot pedal assembly to the foot panel. Remove the foot pedal. n
  • Replace the foot pedal in the reverse order of removal

Removing the Game PCBs

Perform the following procedure to remove/replace the game PCBs. (See Figure 3-4.)

  • Turn the game power off.

3-8

  • Unlock and open the rear door. 3, Use a Phillips screwdriver to remove the two screws holding the upper PCB cleat on the inside of the rear door. Remove the cleat.
  • Remove the screw and washers located in the upper right corner of the PCB board set that hold the set to the rear door. . Disconnect the video harness connector and the main edge connector from the Main PCB. . Tilt the Main PCB and the Cartridge PCB away from the door. Remove the audio connector from the Cartridge PCB. . Remove both the Main PCB and the Cartridge PCB from the bottom PCB cleat. . Replace both the Main and Cartridge PCBs in the reverse order of removal.
Page 31

Road Blasters Maintenance

Standoff

Mini Ground Plane

PCB Cleat

eet eh it Lock Wesher, Nylon Spacer Sind Fiat Weaher

LSI Cartridge 5 PCB Assy

Foam Damper.

LSI Main PCB Assy Standoft

PCB Hamess Assy

Nvlon Spacer Ribbon Cable Assy

Figure 3-4 Game PCB Removal

Removing the Speakers

CAUTION The Road Blasters game contains three speakers. Two small speakers are located in the upper corners of the control panel. One large speaker is located on the foot pedal panel below the control panel. Perform the following procedure to remove/replace the speakers. (See Figure 3-1.)

Control Panel Speakers

  • Turn the game power off.
  • From the front of the control panel, use a 4-inch hex driver to remove the four screws holding the speaker and grille to the control panel. Do not let the speaker fall. Do not touch the speaker cones when handling the speakers. The cone material is fragile and can be easily damaged.

as . Lower the speaker just far enough to disconnect the two speaker wires. Ensure that the speakers are properly phased by placing the same color-coded connector on the same tab on each speaker.

. Replace the speaker in the reverse order of removal.

Page 32

Maintenance

Foot Pedal Panel Speaker Perform the following procedure to remove/replace the speakers.

  • Turn the game power off. Road Blasters

. From the front of the foot pedal panel, use a {inch hex driver to remove the four screws holding the speaker grille to the foot pedal panel. . Use a Phillips screwdriver to remove the four screws holding the speaker. Do not let the speaker fall. . Follow steps 3 and 4 in the preceding procedure.

Page 33

Chapter 4

Troubleshooting

The information in this chapter discusses troubleshooting aids and techniques to assist the service technician when trouble is suspected in a game. Most troubles can be located quickly by following the information in this chapter. However, if problems persist, contact your local distributor or your Atari Games Corporation Customer Service Office, listed on the inside front cover of this manual, for assistance.

NOTE We recommend that troubleshooting and repair procedures be performed by a qualified service technician.
Page 34

Troubleshooting

Troubleshooting Aids

Troubleshooting aids are provided throughout this manual and the schematic package supplement. The foilowing information is intended to acquaint the service technician with the portions of these documents that contain useful troubleshooting and repair information.

Assembly and Component Locations The parts lists in Chapter 5 of this manual illustrate the locations of assemblies and components. Printed-circuit board (PCB) illustrations aid in rapidly locating components shown on the corresponding schematic diagram(s).

Diagrams The schematic package supplement for this manual contains schematic diagrams with component locations, active component type numbers, and electrical values,

Troubleshooting Techniques

A WARNING A

To avoid electrical shock, turn off the game power before attempting to troubleshoot this game,

The following troubleshooting steps are arranged in a sequence recommended for locating a defective component. The procedure begins with a check of the simple trouble possibilities and progresses to more extensive procedures for localizing the problem to an assembly or major circuit, and then to a defective component.

Check Fuses Check for open fuses. Refer to the power supply parts list in Chapter 5 and to the display manual for the location and rating of each fuse used in this game. Make sure that replacement fuses are the proper type and rating.

Check Power-Supply Voltages

Improper operation of all circuits usually indicates a power supply problem, Be sure that the proper line voltage is available to the power supply. Refer to the label on the power supply for its voltage rating.

Localize Trouble

Determine the trouble symptom. Use the wiring diagrams in the schematic package supplement to determine which assemblies or major circuits could cause the trouble. Perform the self-test procedure provided in Chapter 2 of this manual. Road Blasters

Visual Check

Visually check for obvious problems in the portion of the game where the trouble is suspected. For example, check for loose or defective solder connections, integrated circuits Joose in their sockets, loose cable connections, broken wires, and damaged PCBs or components.

Check Individual Components Check soldered-in passive components (¢.g., resistors, capacitors, diodes) by disconnecting one end to isolate the measurement from the effects of the surrounding cixcuitry. Often, direct substitution is the most practical way to determine if a component is faulty, However, eliminate the possibility of some other circuit problem that could damage the substitute component.

Repair the Assembly

CAUTION Soldered-in transistors and integrated circuits are difficult to remove without damaging the printed-circuit board or component. Refer to the | information in this chapter pertaining to soldering and replacing integrated circuits and | transistors.

Repair or replace the defective part. Refer to Chapter 3 and information in this chapter for special removal and replacement procedures. Check for proper operation of the repaired circuit.

Soldering Techniques

Observe the following recommendations when removing or replacing components soldered to a PCB. Poor soldering practices can damage a PCB or heat-sensitive electrical components.

Choosing the proper soldering iron is essential before attempting to remove or replace soldered-in components. Excessive heat is a common cause of damage to a component or PCB. However, transient voltages from solder guns or improperly grounded soldering irons can also damage certain voltage-sensitive semiconductor devices. Refer to Troubleshooting Static-Sensitive Devices for more specific information.

A15-to27-watt pencil-tip soldering iron is recommended to avoid separating the etched circuit wiring from the board material and to avoid damaging active components. A temperature-controiled soldering station rated at 700°F with a fine cone or a very fine chisel tip can also be used.

Page 35

Road Blasters

CAUTION Solder guns are not recommended for removing or replacing soldered-in components on a printed-circuit board. Solder guns can overheat a device, and their large transient voltage can damage a voltage-sensitive device.

The following additional equipment is recommended for removing and replacing soldered-in components: Solder Sucker—-Hand-operated vacuum tool used to remove liquified solder from the PCB, We recommend the top-of-the-line Soldapullt® brand. Solder Wick—Resin-soaked copper braid used for removing excess solder from the lead connections on the PCB. See Removing Integrated Circuits for precautions relating to the use of a solder wick on a multilayer PCB with plated-through holes.

  • Flux Remover—Non-corrosive chemical used to clean foreign material from the PCB before soldering and to remove any flux residue where components have been replaced. Also used to clean any foreign material from the PCB during preventive maintenance. Isopropyl alcohol is recommended.

Acid Brush—Small stiff-bristled paint or toothbrush used with flux remover to clean flux and other foreign material from the PCB.

Removing Integrated Circuits

The easiest and safest method for removing soldered-in integrated circuits (IC) from a PCB is to cut off each pin as close to the IC case as possible with a tip dyke (diagonal cutter) as shown in Figure 4-1. Use the proper soldering iron as previously described undex Soldering Techniques. Then, to avoid excessive heat buildup in one area of the PCB, apply heat directly to each pin in arandom order. Remove the loosened pin with the tip of the soldering iron or a needle-nose pliers as shown in Figure 4-2. Allow amoment for the PCB to cool before

Diagonal Cutter

Figure 4-1 Removing IC (Cut-Pin Method) ‘Troubleshooting

Needie-Nose Pliers

Soldering Iron

Figure 4-2 Removing IC Pins

Proceeding to the next pin. Apply just enough heat to remove any stubborn pins. For a multi-layer PCB with plated-through holes, use a solder sucker to remove the remaining solder from inside each hole as shown in Figure 4-3. If possible, suck the solder from the opposite side of the PCB from where the heat is applied. Use a solder wick to remove excess solder from around the lead connection pads on the top and/or bottom surface of the PCB as shown in Figure 4-4.

CAUTION Do not use a solder wick to remove solder from inside plated-through holes. The heat required for the solder wick to remove the solder from inside the hole could damage the PCB.

Use an integrated-circuit (IC) pulling too! to remove socketed ICs. Do not pry up on one end of the ICs, because the pins could be bent or broken.

Troubleshooting Static-

Sensitive Devices

Certain precautions must be taken when working with static-sensitive devices, e.g.. microprocessors, field-effect transistors (FET), complementary metal-oxide semiconductors (CMOS), and other large-scale integration (LSI) devices that use metal-oxide semiconductor (MOS) technology. Static charge buildup in a person’s body or leakage from an improperly grounded soldering iron can cause static-sensitive device failure.

Before handling a static-sensitive device or a PCB with such devices attached to it, ground any static voltage that may have accumulated in your body by touching an ob-

Page 36

Troubleshooting

| Soldering iron

Solder Sucker

Preferred Method Road Blasters

Soldering Iron

Alternate Method

Figure 4-3 Removing Solder from Plated-Through Holes

Soldering Iron > Solder Wick

~ " = 7,

Figure 4-4 Removing Solder from Lead Connection Pads

ject that has been earth grounded. A bare wire wrapped around your wrist and attached to an earth ground is effective when working extensively with static-sensitive devices. When soldering a static-sensitive device, use a soldering iron with a properly grounded three-wire cord. (Refer to Soldering Techniques for a discussion of recommended soldering irons and procedures.) Astatic-sensitive device can appear defective due to leakage on a PCB. Observe the precautions for grounding static voltages described in the preceding paragraph and clean both sides of the PCB with flux remover or an eraser before replacing what can be a good static-sensitive device. For discrete FETs, clean thoroughly between the gate, drain, and source leads.

Static-sensitive devices can be packaged in conductive foam or have a protective shorting wire attached to the pins. Remove the conductive foam just prior to inserting the device into its socket or soldering it toa PCB. Remove the shorting wire only a/ter the device is inserted into its socket or after all the leads are soldered in place.

Page 37

Chapter 5

Illustrated Parts Lists

This chapter provides information you need to order parts for your game. Common hardware (screws, nuts, washers, etc.) has been deleted from most of the parts lists The PCB parts lists are arranged in alphabetical order by component. Each component subsection is arranged alphanumerically by reference designator. Other parts lists are arranged alphanumerically by Atari part number, In these parts lists, all A-prefix numbers come first. Following these are numbers in sequence evaluated up to the hyphen, namely 00- through 99-, then 000598- through approximately 201000- When ordering parts, please give the part number, part name, number of this manual, and serial number of your game. This will help us fill your order rapidly and correctly, We hope the results will be less downtime and more profit from your game. Atari Customer Service numbers are listed on the inside front cover of this manual.

Page 38

Illustrated Parts Lists Road Blasters

Parts Not Shown: 4044056-01 Test Switch Assy 044237-02 4084072-01 Right Control Panel Decal 12 V Coin Counter Assy 044237-01

padosi-neLeft Cortrol Panel Decal04083-017
Right Trim Plate043978-01Display Shieldonus as1043966-01
04423402148007-104Sontral Ranett|Steering Control Decal

Pgh ne on 4Ye-Inch Speaker | > 24 , 044047-01

Contest MarqueeRound Speaker Grile',~~

044171-1200 1 i ” 044052-01 "inch Cleat | wolf oumzason Fresnel Lens -% : t 7 Right Side Panel Decal

A043945-01i(not shown)

Main Harness Assy 04171-0808 3 043974-01 8Ve-Inch Cleat Corner Cover cdigvnal 044235-01 \ ‘ Left Side Panel Decal > ; _ : oasg67-01 | |, Steering Head Decal

° 044049-01 Control Mounting Bracket

044050-01 Square Speaker Grille 148008-002 8-Inch Speaker

Foot Pedal Assy See Figure 53

044055-01 Floor Covering 786900402 Foam Tape 178023-001 Caster (not shown) 044236-01 Back Panel Decal

A044014-01 coin D Assy Cabinet Assy RTC Steering Control Assy S€2 Fisue 55 See Figure 5:2 038091-01 Con Box

Figure 5-1 Cabinet-Mounted Assemblies A044213-01 B

Page 39

Road Blasters Mustrated Parts Lists

044097-01 Right Visor 139017-204 Video Display Audio |i PCB Assy (A043661-05) A043946-01 See Figure 59 Speaker Harness Assy

044051-01 043995-01 Vent Grille Rear Door

Audio Il PCB Assy (A043661-03) See Figure 5-3

044077-01 Mini Ground Plate

034536-09

A043945-01 Main Harness Assy

A043377-01 ; A043086-04 ‘SL Power Supply Assy Display Power Harness Assy LSI Cartridge 5 PCB Assy Ground Strap Assy See Figure 5-4 See Figure 5-8

i A043910-01 i il On/Off Switch Assy with Harness

Figure 5-1 Cabinet-Mounted Assemblies, Continued A044213-01 B

Page 40

Illustrated Parts Lists Road Blasters

Cabinet-Mounted Assemblies Parts List

Part No. Description

A043086-04 Ground Strap Assembly A043377-01 Display Power Harness Assembly A043910-01 On/Off Switch Assembly with Harness A043945-01 Main Harness Assembly

A043946-01 Speaker Harness Assembly A043948-01 Display Harness Assembly A044014-01 Cabinet Assembly A044056-01 ‘Test Switch Assembly

A044072-01 12 V Coin Counter Assembly 78-3201 Adjustable Glide 78-6900402 Ys-Inch » ¥-Inch Foam Tape (48 inches required; used between lens and control panel cover) 034536-09 1-InchThick Vibration Damper

038091-01 Coin Box 043966-01 RTC Steering Control Cover Decal (with instructions) 043967-01 Steering Head Decal 043974-01 Corner Cover

043978-01 Control Panel (includes laminates and T-molding, but not the decals) 043995-01 Rear Door 044047-01 Round Speaker Grille 044049-01 Control Mounting Bracket

044050-01 Square Speaker Grille 044051-01 Vent Grille 044052-01 Fresnel Lens 044053-01 Display Shield

044054-01 044054-02 044055-01 044077-01

044093-01 944096-01 044097-01 44171-0808 44171-1200 044234-01 044234-02 044235-01

044235-02 044236-01 044237-01 044237-02

044324-01 139017-204 148007-104 148008-002 178023-001

TM-299 SP-299 ST:299 TM-296 Left Metal Trim Plate Right Metal Trim Plate Floor Covering Mini Ground Plate

Printed-Circuit Board (PCB) Cleat with Holes Left Visor Right Visor 8% -Inch Long x %4-Inch Square Painted Cleat with Holes 12-Inch Long x %-Inch Square Painted Cleat with Holes Left Inner Side Decal Right Inner Side Decal Left Side Pane! Decal

Right Side Panel Decal Back Panel Decal Left Control Panel Decal Right Control Panel Decal

Contest Marquee Wells-Gardner 19-Inch Standard-Resolution Color Raster Video Display, Model 19K7901 4% -inch Round, 8 Q Speaker 12-Inch Round, 8 Q, 20 W Speaker 4Anch-Diameter Caster

The following are the technical information supplements for this game: Road Biasters/Cockpit Operators Manual Road Blasters/Cockpit Schematic Package Road Blasters/Cockpit Self-Test Label Wells-Gardner Model 19K7901 Video Display Service Manual

5-4

Page 41

Road Blasters Illustrated Parts Lists

N O T E S

Page 42

Illustrated Parts Lists Road Blasters

NOTE Alter reassembling the RTC steering control, be sure that all necessary screws are prop- 049929-01 erly tightened. See Figure 3-2 for the Screw Steering Head Torque Specifications Table. 042635-02 Left-Hand Handle 042636-02 Left-Hand Handle Cover

040240-01 177010-241 ve Washer er Stop Bumper Hex Nut 28010

Screw (3 each)

DB 160026-001 x Switch 73-20807 Roll Pin 040303-01 Trigger 042636-01 Right-Hand Handle Cover

L | | 5 oa26as‘o1 | “Right-Hand Handle

178203-001 Cap 176022-3606 72-1206F Screw s coc Screw (8 each) 176022-3610 042045-01 160026-001 Screw (4 each) Bushing Switch 73-21208 043950-01 040252-01 Roll Pin Conical Spring Compression Spring

040473-01 Jumper Wire

Figure 5-2 RTC Steering Control Assembly A043968-01 D

5-6

Page 43

Road Blasters Illustrated Parts Lists

040235-01 Spur Gear with Hub A043942-01 175002-001 176022-3604 Harness Assy Washer Screw J 178012-001 .750 Diameter Retaining Ring

4 107013-001 1 7-001 Lubricant Penetrating Adhesive 040237-01 Anchor Nut

‘4.178027-001 Lubricant 040239-01 75-0148 Spring sh Washer 178101-002 043928-01 Spur Gear Base \ '044023-02 or -01 Q ‘Spacer 040240-01 044024-01 Stop Bumper Encoder Disc

04402201 040241-01 ‘Encoder Shaft Spacer Bearing

A043937-01 Coupler PCB Assy

178118-001 Sleeve Bearing

178097-001 A 175002-04 Bearing with Washer/Nut 040240-¢ Stop Burnper Washer 040238-01 AZOiD-28t 175009-170 Anchor Pin Hex Nut Washer 178012-003 %« Diameter Retaining Ring

Figure 5-2 RTC Steering Control Assembly, Continued A043968-01 B

5-7

Page 44

Illustrated Parts Lists

RTC Steering Control Assembly Road Blasters

Parts List

Part No. Description

A043937-01 Coupler PCB Assembly A043942-01 Control Harness Assembly 72-1206F 2-56 x %Inch Cross-Recessed Pan-Head Machine Screw

73-20807 73-21208 75-0448 75-07010 75-0148 040235-01 040237-01 040238-01 040239-01 040240-01 040241-01 040252-01 040303-01 040473-01 042044-01 042045-01 042635-01

042636-01 942036-02 043928-01 043929-01 043930-01 043950-01

044023-02 044024-01 044214-01 106007-001 107013-001 160026-001 175002-001 175002-004 175009-170, 176022-3604 176022-3606 176022-3610 176035-1820 177010-241 178012-001 178012-003 178027-001 178065-100 178068-200 178097-001 178101-002 178118-001 178203-001 10-32 x Inch Socket-Head Cap Screw ) x -Inch Socket-Head Cap Screw 6-32 “s-Inch Hex Washer-Head Thread-Forming Machine Screw YeJnch Diameter x %,-Inch Spring Roll Pin ¥einch Diameter x %-Inch Spring Roll Pin #4 Split-Lock Washer 320 LD., .750 O.D., .015 Thick Special Washer #4 Steel/Zinc Flat Washer GOT Spur Gear with Hub Anchor Nut Anchor Pin Torsion Steering Spring Stop Bumper Spacer Bearing Compression Spring Trigger Jumper Wire Button Bushing Machined Handle (Right-Hand) Machined Handie (Left-Hand) Machined Handle Cover (Right-Hand) Machined Handle Cover (Left-Hand) Base Steering Head Cover Conical Compression Spring Encoder Shaft Encoder Shaft Spacer (Acceptable substitute is part no, 044023-01) Etched Encoder Disc Brace Penetrating Adhesive Lubricant Switch, Snap, SPDT Large Washer with 34-Inch Diameter Shaft #10, .062 Thick, Flat Washer Special Nylon Flat Washer 6-32 x %4-Inch Self-Locking Socket-Head Cap Screw 6-32 x ¥-Inch Self-Locking Socket-Head Cap Screw 632 x Inch Self-Locking Socket-Head Cap Screw 8-32 x 1 Y-Inch Black Type F Socket-Head Cap Screw #10-32 Nyloc Hex Nut Retaining Ring for¥%4-Inch Diameter Shaft Retaining Ring for -Inch Diameter Shaft Lubricant 4-Inch Wire and Cable Tie Cable Tie Mount 25 Shaft Panel Bearing with Lock Washer and Nut 24 DP x 20 PA x .583 P.D. x 2.50 Spur Gear Oil-Impregnated Sleeve Bearing Cap

Page 45

Road Blasters Illustrated Parts Lists

A043947-01 (Foot pedal harness assy—not shown)

039240-01 039236-01 . KC os 2 2 4 (Foot pedal—accelerator) (Pivot pin) «

040028-01 a (Compression spring) 178012.004, . (Retaining ring) : (Cable)

039704-01 (Extension spring) 72-8606 me (3+. (Cap screw) Cap screw of pulley must be in this position when pedal is fully is rest). 039239-01 (Base plate) 039703-01 (Cable spring)

72-HB3410S a (Screw) (Potentiometer) z ' : 72-030S 160023-001 (Lock washer—used for (Switch) securing ground lug Not shown)

0440. 1 SS (Mowing plate)

75-0108 4 177010-240 (Hex locknut)

= NYOGEL 779 (Washer) <5 wro10-200_ I = WD-40 (Hex locknut)

Figure 5-3 Foot Pedal Assembly A044091-01 A

Page 46

Illustrated Parts Lists Road Blasters

Foot Pedal Assembly Parts List

Part No. Description

19-9026 5 kQ Potentiometer (Acceptable substitute is part no. 19-9022) 72-0308 #40 External-Tooth Lock Washer 72-8606 #6-32 x .38-Inch Hex Socket-Head Cap Screw 75-0108 #10 Flat Washer

75-0358 1/4-Inch Flat Washer 75-5520B #1/4-20 x 1%-Inch Black Carriage Bolt 75-9158 #1/4-20 Hex Nut 03923601 Pivot Pin 039238-01 Pulley 039239-01 Foot Pedal Control Base Plate 039240-01 Foot Pedal Accelerator 039241-01 Safety Tread

039242-01 Cable 039703-01 Extension Spring for Cable 039704-01 Extension Spring for Pedal 040028-01 Compression Spring for Pedal 044048-01 Pedal Mounting Plate 107012-001 Dry Teflon Spray Lubricant 160023-001 SPDT Snap Switch with Actuator 177010-240 #10-24 Hex Locknut

178012-004 External Retaining Ring for 3/8-inch Diameter Shaft A043947-01 Gas Pedal Harness Assembly

Page 47

Road Blasters Illustrated Parts Lists

A WARNING A This 5-volt switching power supply may not have a shield as illustrated below. The power supply has high voltages on it when power is turned on. Therefore, be sure you do not touch this power supply unless you have tured off the power to the game

72-HA4606S, 149003-xxx Screw 5V 10 Amp Switching Power Supply Assy

A043367-xx 179231-002 4 i Jumper Assy Terminal Block ) g ‘ 42042-001

A043367-xx Jumper Assy

A043366-01 5V Harness Assy : | 72-HA4806S | Screw

043396-01 Power Supply Chassis Base

A042384-01 Line Filter Assy

46-2013002 Fuse

037640-01

Warning Label

179225-2205, or 79-3206 Fuse Block

034544-01 Fuse Block Cover

043622-01 Fuse Label 46-2012002 Fuse

Figure 5-4 Switching/Linear (SL) Power Supply Assembly A043787-01 A

5-11

Page 48

Mlustrated Parts Lists,

Switching/Linear (SL) Power Supply Assembly Road Blasters

Paris List

Part No. Description

A042384-01 Line Filter Assembly A043366-01 5 V Harness Assembly A043367-01 Jumper Assembly A043367-02 -Inch, Black Jumper Assembly

A043367-03 46-201 2002 46-2013002 72-HA4G606S

72-HA48065 034544-01 037640-01 043396-01

043622-01 142042-001 149003-003 179. 205 6-Inch, White Jumper Assembly 250 V Slow-Blow 2 A Fuse 250 V Slow-Blow 3 A Fuse #0-32 x %-Inch Cross-Recessed Pan-Head Thread-Forming Screw

#8-32 x *4-Inch Cross-Recessed Pan-Head Thread-Forming Screw Fuse Block Cover Power Supply Warning Label Power Supply Chassis Base Power Supply Fuse Label Transformer Hitron 5 V 10 A Switching Power Supply Sub-Assembly 5-Position Fuse Block (Acceptable substitute is part no. 79-3206) 179231-002 2-Position Terminal Block

Hitron 5-Volt Power Supply Sub-Assembly Parts List

DesignatorDescriptionPart No.

Capacitors

‘cLCAPACITOR, METAL FILM, 0.047 uF, 250 V99-21 1036
c2CAPACITOR, METAL FILM, 0.1 uF, 400 V99-211038
C3, C4CAPACITOR, CERAMIC, 4700 pF, 400 V99-211049
C3, C6CAPACITOR, ELECTROLYTIC, 100 uF, 200 V99-211046
C7CAPACITOR, METAL FILM, 0.1 pE 400 V99-21 1038
csCAPACITOR, CERAMIC, 0.001 pf,2kV99-211042
coCAPACITOR, CERAMIC, 0.01 gE, 1 kV, Z5U99-211041
cleCAPACITOR, ELECTROLYTIC, 220 pF, 25 V99-211045
cuCAPACITOR, METAL FILM, 0.22 4F, 100 V99-211037
ci2CAPACITOR, METAL FILM, 0,022 yF 100 V99-211039
C13CAPACITOR, METAL FILM, 0.22 2, 100 V99-211037
Ci4CAPACITOR, CERAMIC, 1800 pK 2 ky, Z5 V99-211040
C17CAPACITOR, ELECTROLYTIC, 470 aE 23 V99-211044
cioCAPACITOR, ELECTROLYTIC, 2200 pE 16 V99-21 1048
C20CAPACITOR, ELECTROLY, 1000 uF, 25 V99-21 1047
C21CAPACITOR, CERAMIC, 470 pF, 1 kV, Z5P99211043
C22CAPACITOR, ELECTROLYTIC, 2200 pk, 16 V99-211048
C23CAPACITOR, ELECTROLYTIC, 1000 uF, 25 V99-21 1047
C24CAPACITOR, ELECTROLYTIC, 2200 pk, 16 V99-211048

Diodes Di, D2 DIODE, FAST RECOVERY, RPG10K 211010

D3DIODE, FAST RECOVERY, RPG15B99-211011
D4DIODE, FAST RECOVERY, RPG10B99-211009

D5-D7 SWITCHING, 1N4148 99-211012

5-12

Page 49

Road Blasters

Hitron 5-Volt Power Supply Sub-Assembly Parts List, Continued Illustrated Parts Lists

DesignatorDescriptionPart No.
D9DIODE, FAST RECOVERY, 30DF |99-211006
Di, DI2DIODE, SCHOTTKY, S1O0SC4M99-211005
D13-D16DIODE, RECTIFIER, 1N400699-211008

Inductors

LLINDUCTOR, 15 mH99-211052
L3,INDUCTOR, 7 #H (Acceptable substitute is part no, 99-211051)99-211050.
L4INDUCTOR, 2.2 «H99-211054
LSINDUCTOR, 1.5 mH99-211053,

Resistors

RI,R2RESISTOR, CARBON FILM, 180 kQ, +5%, 1 W99-211034
R3RESISTOR, WIREWOUND, 120 2, +5%,2W99-211019
R4RESISTOR, WIREWOUND, 0.470, +5%, 2 W99-211018
RSRESISTOR, WIREWOUND, 33 @, +5%.2W99-211017
5RESISTOR, CARBON FILM, 5.68, +5%,4 W99-211027

RESISTOR, WiREWOUND, 0.47 9, +5%, 2 W 99-211018

RORESISTOR, CARBON FILM, 10 Q, +5%,%4 W99-211029,
RIORESISTOR, CARBON FILM, 1 kQ, +5%,4 W99-211032
RilRESISTOR, CARBON FILM, 479, +5%,'4 W99-211025
R12RESISTOR, CARBON FILM, 5.62, +5%,'4 W99-211027
RI3RESISTOR, CARBON FILM, 3309, +5%,%4W99-211026
R14RESISTOR, CARBON FILM, 270, +5%,% W99-211023
RISRESISTOR, CARBON FILM, 3300, +5%,¥2 W99-211022
R16RESISTOR, CARBON FILM, 8.20, +5%,% W99-211028
R17, RIBRESISTOR, CARBON FILM, 569, +5%,% W99-211031
R19RESISTOR, CARBON FILM, 399, +5%, 4 W99-211030
R20RESISTOR, CARBON FILM, 2 k@, +5%,14 W99-211035
R21RESISTOR, CARBON FILM, 4702, +5%,%4 W99-211024
R22RESISTOR, 2.2 kQ, + 2%, W99-211021
R23RESISTOR, METAL FILM, 2 kQ, 42%, 4 W99-211033
R25RESISTOR, CARBON FILM, 100, +5%,4 W99-211029
R26RESISTOR, WIREWOUND, 500, +5%, 2W99-211015
R27RESISTOR, CARBON FILM, 47 @,+5%,% W99-211025
R31RESISTOR, WIREWOUND, 1502, +5%,2W99-211016

“ransistors

QlTRANSISTOR, NPN, 28C1413A99-241002
Q2TRANSISTOR, NPN, PE8050B99-211003
Q3TRANSISTOR, PNP, PE8550B99-211004

Miscellaneous

FIFUSE, 2 A, 250 V. SEMKO99-211058
IC]REGULATOR, UA43 AWC99-211001
SCRITHYRISTOR, SCR, $280099-211013
TITRANSFORMER99-211055
TRITHERMISTOR, 0.5 9, 45%, 5 W99-211020
VRIPOTENTIOMETER, TRIMMING, 3 kQ99-211014
ZDIDIODE, ZENER, IN752A99-211007

FUSE, 2 A. 250V 99-211056

FUSE HOLDER, 6.35 mm 99-211060 TERMINAL BLOCK, 8 CKT 99-211057 HEAT SINK 99-211059 HEAT SINK, 1.5 mm. 99.211061

5-13

Page 50

Ilustrated Parts Lists Road Blasters

99-10140 Panel Assembly 75-948S Locknut —

99-10152 Right Coin Inlet oy

171006-035 Coin Mechanism 99-10116 Lever

99-10147 Harness

75-9448 Locknut

99-10096 Fastener

99-10151 Left Coin Inlet

70-11-47 Lamp

99-10080 Lamp Socket

98-10105 Bar

99-10104 Bar Retainer

99-10042 thru 99-10045

99-10154 Coin Switch Assembly

Bracket Assembly

99-10153 Coin Return Box 99-10150 Switch Cover 99-10068 Coin Chute 65-441C Coin Switch

99-10075 thru 99-10078 Switch Wires 99-10008 Retainer 75. 44125 Screw

Figure 5-5 Coin Acceptors, Inc. Coin Door Assembly 171027-001 A

Page 51

Road Blasters Illustrated Parts Lists

99-10148 Lock Assembly

99-10142 Button Housing

72-HA1404C Screw

99-10134 99-10119 Cover 99-10139 > j~————— Button Assembly | 99.10118

Coin Door Button

. 99-0115 99-10148 Spring Lock Assembly

. 99-10141 Coin Return Cover

99-10117 Coin Return Door

72-JA1405B Screw ZZ \—— 9910144

@ Channel Clip

Sen 99-15066 Screw

99-10149 Service Door

038091-01 ———— Coin Box

99-10143 Frame

NOTE The acceptable substitute for this door (and the one used in games manufactured in Ireland) is the Coin Controls. Inc. Coin Door Assembly, part | number 171034-001

Figure 5-5 Coin Acceptors, Inc. Coin Door Assembly, Continued 171027-001 A

5-15

Page 52

Illustrated Parts Lists Road Blasters

Coin Acceptors, Inc. Coin Door Assembly Parts List

Part No. Description

65-441C Coin Switch 70-11-47 Miniature Bayonet Lamp 72-94068 #4-40 x %-Inch Truss-Head Screw 72-HA1404C #4-40 x Ya-Inch Pan-Head Screw

72-JA1405B #4-40 x 0.31-Inch Pan-Head Screw 75-14128 #4-40 x %-Inch Pan-Head Screw 75-9945 #4-40 Locknut 99-10008 Retainer

99-10042 Coin Switch Assembly for Belgian 5 Fr and U.S. $.25 99-10043 Coin Switch Assembly for German 1 DM, Japanese 100 Yen, Swiss i Fr 99-10044 Coin Switch Assembly for German 2 DM, Italian 100 L, U.S. $1.00 99-10045 Coin Switch Assembly for Australian $.20, German 5 DM, British 10 P 99-10068 Coin Return Chute

99-10075Switch Wire(included in coin switch assembly 99-10043)
99-10076,Switch Wire(included in coin switch assembly 99-10042)
99-10077Switch Wire{included in coin switch assembly 99-10044)
99-10078Switch Wire(included in coin switch assernbly 99-10045)

99-10080 Lamp Socket 99-10081 Key Holder 99-10096 Fastener

99-10104 Bar Retainer 99-10105 Bar 99-10115 Spring 99-10116 Plastic Coin Return Lever

99-10117 Steel Coin Return Door 99-10118 Amber Coin Return Button 99-10119 Amber Coin Button for U.S. $.25 99-10134 Coin Button Cover

99-10139 Coin Door 99-10140 Coin Door Inner-Panel Assembly 99-10141 Die-Cast Coin Return Cover 99-10142 Die-Cast Button Housing

99-10143, Coin Door Frame 99-10144 Channel Clip 99-10147 Harness 99-10148 Lock Assembly

99-10149 Service Door 99-10150 Switch Cover 99-10151 Left Coin Inlet 99-10152 Right Coin Inlet

99-10153 Coin Return Box 99-10154 Bracket Assembly 99-15066 Screw for Clamp 171006-035 Metal Coin Mechanism for U.S. $.25

5-16

Page 53

Road Blasters

178171-1612 ‘Standoff

044093-01 PCB Cleat Illustrated Parts Lists

044077-01 Mini Ground Plane

72-1612F Screw 178050-112 75-046S Spacer, Split Lock Washer 75-0168 Flat Washer LSI Cartridge 5 PCB Assy See Figure 5-8 034536-13 | sretzs-t612 Foam Damper Standott 72-1606F Screw LSI Main PCB Assy, 75-016 See Figure 57 Fiat Washer ee Noure 75-0468 A044211-01 Split Lock Washer PCB Harness Assy Le

178050-112 Nylon Spacer A044212-01 Ribbon Cable Assy

Figure 5-6 PCB Mounting Hardware A044098-01 B

PCB Mounting Hardware Parts List

Part No. Description

A044211-01 PCB Harness Assembly A044212-01 Ribbon Cable Assembly 72-1606F #6-32 x ¥-Inch Cross-Recessed Pan-Head Machine Screw 75-016 #6 Flat Washer

75-0468 #6 Split Lock Washer 034536-13, 3 x3 x %-Inch Foam Vibration Damper 044077-01 PCB Mini Ground Plane 044093-01 PCB Cleat, Removable

178050-112 ¥4-Inch Nylon Dual-Locking Circuit Board Spacer 178171-1612 #6-32 x %-Inch Aluminum Threaded-Through 1% -Inch Diameter Standoff

5-17

Page 54

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 55

Road Blasters Illustrated Parts Lists

Road Blasters/Cockpit LSI Main PCB Assembly Parts List

Desig- Desig-

nator—_DescriptionPart No.natorDescriptionPart No.
Integrated CircuitsSK 5H, 5]IC, 741515337-74LS153
12LIC, PFHS137419-1045K,5MIC, AMD2918-10137348-003
1A,1BIC, 741824437-74LS244SNIC, 7418273,37-7418273
1C,1DIC, 741825737-74LS257SP,5RIC, 740737-7407
IE,1FIC, 741827337-74L8273
BIC, 7487437-74874
1HIC, 741825737-74LS2576c,6DI$37337-74L8373,
uIC, 7418283137204-001OEIC, 741813937-T4L8139
WKIC, 74188637-74LS86GE 6H, 6)IC, 74815337-741S153
1KIC, 7418283137204-001
6KIC, 74LS08,37-74LS08
IMIC, 74820137423-0016LIC, 74LS8637-74LS86
INIC, 741817437-74LS1746MIC, 7487437-74L874
1PIC, 27128-300136032-120TI8LIC, GPC137419-101
IRIC, 7418194 A37-741S194
TAIC, 74LS0237-74LS02
21C, 23DIC, LBC137419-1027BIC, 7487437-74LS7
2A,2BIC, 214983137199-0017C,7DIC, 74/824474LS244
2E,2F—_IC, 74LS8637-74LS86JEIC, 74180037-74LS00
2HIC, 741837437-74LS374
JEIC, 74LS27337-74L8273
2IC, 741815337-74LS153,7HIC, 74LS17437-74LS174
2KIC, 741827337-74LS2737IC, 74L$138137177-001
2MIC, 74188637-T4LS867KIC, 741824537-T4LS245
2NIC, 7480837-74S08

™ 37-74LS32

2PIC, 7418194 A37-74LS1948A137168-001
3A, 3BIC, 2149H-3,137199-0018BIC, 74LS148137417-002
3EIC, 7450237-748028C,8DIC, 741824537-74L8245
3FIC, IMS1420L137360-001

8E IC, 7407

3F/HIC, IMS1420L137360-0018FIC, 74L20
3HIC, IMS1420L137360-0018HIC, 741874
3JIC, IMS1420L137360-0018), 8KIC, 74L8138
3KIL,3LIC, 7415283137204-001
8MIC, 7415245,37-74 18245,
3MIC, 74L817437-74LS1748NIC,74LS197137240-001
3NIC, 74181437-74LS149B, 9B/CIC, 7T4LS3237-74L832
3PIC, 741817437-74LS1749cIC, 74181437-74LS14
4/5EIC, SYNGEN137419-103
oFIC, 68010137414001
4A,4BIC, 748374137206-0019KIC, 741824437-74LS244
4CIC, 74L$368 A137168-001OLIC, 27128-200136032-117
4DiC, 741815137-74LS151OMIC, 27128-200136032-116
4FIC, IMS1420L137360-001
10AIC, 74L83237-74LS32
45/HIC, IMS1420L137360-00110BIC, 7ALS74
4H)IC, IMS1420L137360-00110BICIC, 74LS163. A
4IC, IMS1420L137360-0011oDIC, 741824437-T4LS244
4NIC, 7418273,37-7ALS273,
10EIC, 74L824537-74L8245
4PIC, 740737-740710F, 10HIC, HMG116137211-001
4RIC, 74526037-748260loyIC, 741824437-T4LS244
5A-5CIC, 74LS19137-74LS19110KIC, 7418245,37-T4LS8245,
sDIC, 748240137416-001

5-19

Page 56

‘ustrated Parts Lists Road Blasters,

Road Blasters/Cockpit LSI Main PCB Assembly Parts List, Continued

Desig- Desig-

natorDescriptionPart No.natorDescriptionPart No.
10LIC, Leta137304-1001QlTransistor, 2N604434-2N6044
1OL/M,IC, 74L824437-7ALS244Ql‘Transistor, 2N604434-2NG044
10M1c, ADCO809137243-001
11AIC, 7418367 A37-7418367Resistors
R1Resistor, 1 KQ, +5%, 4 W110000-102
11B, 11B/C 1G, 74L837437-T4L8374R2Resistor, 2209, 45%, 4 W110000-221
IEIC, 74L824537-74L8245,R3Resistor, 1 KQ, +5%, 4 W410000-102,
IIR 11HtC, HMO116137211-001R4,R5Resistor, 4.7 KQ, +5%, 4 W1190000-472
lyIC, 741824437-74L8244
WKIC, X2804 A137329-450ROResistor, 10 KQ, +5%, 4 W110000-103
R7-R9Resistor, 4.7 KQ, 15%, 4 W110000-472
CapacitorsR10, R11Resistor, 10 KQ, +5%, 4 W110000-103
cl, C2Capacitor, 100 pF, 25 V,24-250107Ri2Resistor, 4.7 KQ, +5%, 4 W110000-472

Electrolytic

C3Capacitor, 22 nF, 35 V, Electrolytic24-350226R1I3-RI17_Resistor, 1 KQ,15%, % W110000-102
4, C5,Capacitor, .1 ¢F 50 V, Ceramic122002-104R18-R20Resistor, 10 KQ, +5%, 4 W110000-103
C6-C8Capacitor, 470 pF, 50 V, Ceramic122013-471R21Resistor, 470.2, +5%, 4 W110000-471
R22-R25_—Resistor, 272, +5%, 4 W110000-270
coCapacitor, 1000 pF, 100 V,122016-102
CeramicR26Resistor, 2.2 KQ, +5%, 4 W110000-222
Capacitor, .1 uF, 50 V, Ceramic122002-104R27Resistor, 4.7 KO, +5%, 4 W110000-472
Capacitor, 10 wE 25 V, Electrolytic24-250106R28Resistor, 10 KQ, +5%, 4 W110000-103
Capacitor, .1 aE 50 V, Ceramic122002-104R29Resistor, 20 KO, +5%, 4 W110000-203
Capacitor, .61 E25 V, Ceramic122005-103R30-R33_—Resistor, 1002, + 5%, 4 W110000-101
Capacitor, .1 uF, 50 V, Ceramic122002-104R34Resistor, 2.49 KQ, +1%, 4 W,110011-252
Capacitor, 10 pF, 25 V, Electrolytic24-250106Metal Film
C58-C1il Capacitor, .1 ¢R 50 V, Ceramic122002-104R35Resistor, 4.99 KQ, +1%, % W,110011-502

Metal Film

cH2Capacitor, 10 aE 25 V, Electrolytic — 24-250106R36Resistor, 10 KO, +5%, 4 W110000-103
C14,Capacitor, .01 uF, 25 V, Ceramic122005-103
C1lsR37Resistor, 20 KQ, + 5%, 4 W110000-203
Ch16-Capacitor, .i nF, 50 V, Ceramic122002-104R38Resistor, 2.2 KQ, +5%, 4 W110000-222
clloR39Resistor, 4.7 KQ, +5%, 4 W110000-472
R40Resistor, 10 KQ, +5%, 4 W110000-103

Diodes

CRIDiode, MV5053, Light-Emitting38-MV5053,R41Resistor, 20 KO, +5%, 4 W110000-203
CR2Diode, 1N400131-1N4001R42, R43Resistor, 2.2 KO, +5%, 4 W119000-222
CR3, CR4_ Diode, 1N4148131033-001R44Resistor, 4.7 KQ, +5%, 4 W110000-472
CRSDiode, MV5053, Light-Emitting38-MV5053R45Resistor, 1OKQ, +5%, 4 W110000-103

CR6, CR? Diode, 1N4001 31-1N4001

R46Resistor, 20 KQ, + 5%, 4 W110000-203
InductorsR47Resistor, 510 2, + 5%, 4 W110000-511
LIInductor, 68 wH141016.008R48, R49Resistor, 10 KQ, + 5%, 4 W110000-103
L2-L4Inductor, | wH, 830 mA141007-001R50Resistor, 1 KQ, +5%, 4 W110000-102
‘TransistorsRSIResistor, 680, +5%, 4 W110000-680
Ql, Q2‘Transistor. 2N390434-2N3904R52Resistor, 122, +5%, 4 W410000-120
Q3, Q4‘Transistor, 2N390633-2N3906R53Resistor, 5109, +5%, 4 W110000-511
O5Transistor, 2N364334-2N3643R54Resistor, 689, +5%, 4 W110000-680,
Q6, Q7Transistor, 2N390434-2N3904
R55, R56Resistor, 5102, +5%, % W110000-511
Q8‘Transistor, 2N390633-2N3906RS7Resistor, 682, +5%, 4 W110600-680
QoTransistor, 2N390434-2N3904R58Resistor, 129, +5%, 4 W110000-120
Q10Transistor, 2N390633-2N3906R59Resistor, 682, +5%, 4 W110000-680
ROOResistor, 122, +5%, 4 W140000-120
ROLResistor, 2200, 45%, 4 W110000-221

5-20

Page 57

Road Blasters Illustrated Parts Lists

Road Blasters/Cockpit LSI Main PCB Assembly Parts List, Continued

Desig- Desig:

natorDescriptionPart No.natorDescriptionPart No.
R62, R63Resistor,4.7 KQ, +5%, & W110000-472Miscellaneous
RO4Resistor, 150.2, +5%, 4 W110000-151Ji01Connector, 3-Circuit, Header, .250—179069-003

Ctr

ROSResistor, 220 2, +5%, 4’ W110000-221J106Connector, 6-Circuit, Header, 250179069-006
ROGResistor, 150 2, +5%, 4 W110000-151Ctr
RO7-R70__Resistor, 1 KQ, +5%, 4 W110000-102J202Connector, 8-Circuit, Header, 156179213-008
R71, R72Resistor, 2209, +5%, 4 W110000-221Cu Key 3
J204,Connector, 50-Circuit, 4-Wall,179186-001
R73-R75__Resistor, 4702, +5%, 4 W110000-471J205A,Header, Rt 2 Rows
R76-R83_Resistor, 100 2, + 5%, & W110000-101J205B
R84-R89_—Resistor, 1 KQ, +5%, ‘A W110000-102
R90Resistor, 3.3 KQ, +5%, 4 W110000-332Fastener, Nylor81-4302
swSwitch, 4-P66-114P1T
R91Resistor, 1 KQ, +5%, 4 W110000-102YtCrystal Oscillator, 14.318 MHz144008-001
RN1, RN2_ Resistor Network, IKx9Q, +5%,—118010-102Socket, 24-Pin79-42C24

1/8 W, SIP (10-pin)

RN3, RN4 Resistor Network, 330x7 @,—118007-331Socket, 28-Pin79-42C28
+£5%, % W, SIP (8-pin)Socket, 40-Pin79-42C40
RNS, RNG Resistor Network, 10Kx9 Q, — 118010-103Socket, 64-Pin79-42C64
£5%, 1/8 W, SIP (10-pin)Test Point179051-002
RN7Resistor Network, 470x7 9,118007-471

+5%, 1/8 W, SIP (8-pin)

RN8Resistor Network, 3.3Kx7@,118007-332

+5%, %& W, SIP (8-pin)

5-21

Page 58

Figure 5-8 Road Blasters/Cockpit Cartridge 5 PCB Assembly A044203-01 B q

avs a wo PS by ”

= 40k = t] i LS = | ae corse {lle 7

Roe wa oF sae a ° aA he eas SB “wee taeoveanes dl mses oF 2 g ats) 3 . = Bt cS oe 8 136048-XXxXS0 q ce,

a No td ae! ae fa a) sox na THLSier OF 2" i _ : weiTe RTE

Tasawy OR THLSeHF ’ TIL SOy a:

‘a; 4.7K Io “ =F p 4136046-xx10 i y[sstove-mne Ey + (3, Slis6048-xx4a H 136048-XX42_ d a, 136048- aoe HH 1596048-Xx14 a FE 136048-XX17 Hh 136048-XX43 El 1360496-) ve | 5 8 > og 1136048-XX45 tBente AX46 CS .

0 Fa Pf sseove anos ‘ ii 136048-Xxx16

——s 22.280 cana os ME

co rio ke 100,107

oS tr cos Poa

xt rosie -136008- % 137415-104. 4 muse

Neo eal!

437415-101 Bene

ae we B rte aS nearer =

J104 FI

ay 136048-XX03 qe 136048-Xx09 E]13¢048-xx139 Hy } sions ff] 136048-Xx36 Z

7K wa 136048-Xxx02 Of sse01-oae fi +|136048-XX15 aH 2 3 136048-xx37 et) 136046-XX38 dE |

  • 137425-101, fit | 7 f & o Hy 136048-xx01 GF) 136046-xx07 3| 13¢048-Xx11 g]136048-1x39 136048-xx40 Z oO

77k nD w + oy o Ny UrPER our _o

=

cd

a +5u2 10) as rl

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING ‘subject matter of the drawing, Except tor manufacture by ied to reproduce this drawing

lor the subject mater Thereof unless by writen agracment with or wiilen permission from ihe corporation. Illustrated Parts Lists Road Blasters

Page 59

Road Blasters Mlustrated Parts Lists

Road Blasters/Cockpit Cartridge 5 PCB Assembly Parts List

Desig- Desig-

natorDescriptionPart No.natorDescriptionPart No.
Integrated CircuitsOE237-7ALS32
12DIC, PROM, 7484724OF 6H.IC, 74L80437-T4LSO4
IDIC, 7481387/8BIC, 74L824537-74L8245
ILIC, 74L87i8CIc,4437-74L8244

233A IC, TLO84CN

7/8C/D.IC, EPROM, 27128, 300 ns136048-1149
2/3K, 2C/DIC, 74L53078DIC, EPROM, 27256, 300 ns136048-1150
2DIC, PROM, 7484733TI8FIC, HMO116137211-001
2HIC,74L824437-74L82447IC, SLAPSTIC.137412-106
2yIC, EPROM, 27256, 300 ns136048-1 106
7KIC, EPROM, 27128, 200 ns136078-1147
2KIC, EPROM,6, 300 ns136048-11057k.IC, EPROM, 27256, 200 ns130048-1141
2LIC, EPROM,2, 300 as136048-1L107MIC, EPROM, 27256, 200 ns136048-1143
2MIC, EPROM,27256, 300 ns136048-1104INIC, EPROM, 27256,200 ns.136048-1145
2N1C, EPROM, 27256, 300 ns136048-1 103

1C, EPROM, 27256, 200 ns 136048-1135,

IC, EPROM,136048-1 108,IC, EPROM, 27.200 ns136048-1137
IC, EPROM,136048-11021G, EPROM, 27256, 200 ns136048-1139
IC, EPROM, 273136048-1101IC, Interface Adapter, 65224.137260-001

IC, LM324 37-LM324

3FIC, HMO116137211-001
3/4FIC, 74L8277-74LS27ayIC, 74L$24437-T4LS244
3H24448KIC, EPROM, 27128, 200 ns136048-1148
3b.536048-11188L.IC, EPROM, 27256, 200 ns136048-1142
3M.iC, EPROM,136048-1 114
8MIC, EPROM,130048-1144
3NIC, EPROM,136048-1 LOD8NIC, EPROM,136048-1146,
3PIC, EPROM,136048-1116BP1C, EPROM, 27256, 200 ns136048-1136
8RIC, EPROM, 27256, 200 ns130048-1138
3RIC, EPROM, 27512,300 ns.136048-1112
38IC, EPROM, 27512, 300 ns130048-11078SIC, EPROM, 27256, 200 ns130048-1140.

TC, 74L800 37-74L800 1C, 74LS00 I S32 Capacitors

IC, 74LS161Capacitor, .1 pF, 50 V, Cera122002-104
4AIC, YM2151Capacitor, 10 pF, 35 V.50106

Capacitor, 1 #F, 50 V, Ceramic 122002-104 4B IC, YM3012

4CIC, LM324Capacitor, .0068 aE, 50 V, Ceramic122015-682
4EI$16137.
4H4437-74LS244C30Capacitor, 1000 pF, L00 V, Mica128002-102
C31Capacitor, | pF, 50 V, Electrolytic24-500105
4MIC, EPROM, 27512, 300 ns136048-111732Capacitor, .22 wF, 25 V, Ceramic122004-224
aNIC, EPROM, 27512, 300 ns136048-1 113C33Capacitor, 01 w¥, 25 V, Ceramic122005-103

4R 136048-1115

48136048-1111Capacitor, 10 pF, 35 V, Electrolytic24-350106

Capacitor, .1 uF, 50 V, Ceramic 122002-104

5A37-TALS245Capacitor, .0027 wE, 50 V, Ceramic122015-272
OITA137308-002Capacitor, .0012 pF, 50 V, Ceramic122015-122
67DIC, 748244Capacitor, .018 pF, 50 V, Ceramic122015-183,
OTECapacitor, .22 pF, 25 V, Ceramic122004-224
C48, C49Capacitor, .1 aE, 59 V, Ceramic122002-104
O7HIC, 748138137177-00150Capacitor, .001 pF, 50 V, Ceramic122002-102
OBIC, POKEY137430-001
6c6502 A90-6013C51Capacitor, 10 pF, 35 V, Electrolytic24350106
oD.37-T4L825952-C54—Capacitor, .1 wR 50eramic122002-104
C55Capacitor, .0039 pF, 50 V, Ceramic122015-392

C50 Capacitor, .22 wE, 25 V, Ceramic

Page 60

Mlustrated Parts Lists

Road Blasters/Cockpit Cartridge 5 PCB Assembly Road Blasters

Parts List, Continued

Desig-*Desig-
natorDescriptionPart No.natorDescriptionPart No.
C57Capacitor, 10 pF, 25 V, Electrolytic24-250106R48Resistor, 5.6 KQ, +5%, 4 W110000-562
58-C61Capacitor, 1000 pF, 100 V, Mica128002-102ROResistor, 10KQ, +5%, 4 W110000-103
C62Capacitor, .01 wF, 25 V, Ceramic122005-103
C63Capacitor, .1 wf, 50 V, Ceramic122002-104RS5O, RSIResistor, 22 KQ, +5%, 4 W110000-223
R52Resistor, 10 KQ, +5%, 4 W110000-103
C64-C67Capacitor, 4.7 pF, $0 V, Electrolytic24-500475RSSResistor, 1 KQ, 45%, 4 W119000-102
C68, C69Capacitor, .0027 pF, 50 V, Ceramic122015-272R56Resistor, 10 KO, 45%, 46 W110000-103
C70-C72Capacitor, .1 wF, 50 V, Ceramic122002-104
C73, C74 — Capacitor, 1 pF, 50 V, Electrolytic24-500105R57Resistor, 39 KQ, +5%, 4 W110000-393,
R58Resistor, 3902, £5%, 4 W110000-391,
forb)Capacitor, 100 pF, 100 V, Ceramic122016-101R59Resistor, 10 K®, +5%, 4 W110000-103
C76Capacitor, 10 pF, 25 V, Electrolytic24-250106ROO, R6LResistor, 15 KQ, +5%, 4 W110000-153,
C77-C87Capacitor, .1 pF, 50 V, Ceramic122002-104
C88-C91Capacitor, 4.7 wF, 50 V, Electiolytic24-500475RO2Resistor, 3.3 KQ, 45%, 4 W110000-332
R63,Resistor, 10KQ, +5%, 4 W110000-103
€92-C105Capacitor, .1 wF, $0 V, Ceramic122002-104R64, ROSResistor, 3300, +5%, 4 W110000-331
C106-C109 Capacitor, 4.7 wF, 50 V, Electrolytic24-500475,ROOResistor, 3902, +5%, 4 W119000-391
cioCapacitor, 100 pF, 25 V, Electrolytic24-250107
cilCapacitor, .1 pF, 50 V, Ceramic122002-104R67Resistor, 3600, 45%, 4 W110000-561
R68Resistor, 1 KQ, +5%, 4 W110000-102
TransistorsR69, R70Resistor, 3302, +5%, 4 W110000-331
QlIC, 7910537-F9LOSR71Resistor, 10 KQ, +5%, 4 W110000-103
Q2,.Q3‘Transistor, 2N390633-2N3906
4Transistor, 2N390434-2N3904R72Resistor, 1 KO, + 5%, 4 W110000-102
R73,R74Resistor, 3.3 KQ, 45%, 4 W110000-332
ResistorsR75Resistor, 10 KQ, +5%, 4 W110000-103
R17-R20,Resistor, 4.7 KQ, +5%, 4 W110000-472RILI,Ril2 Resistor,02, 4 W110005-001
R22RNI-RN7__Resistor Network, 4.7Kx9Q, +5%, {4 — 118010-472
R23.Resistor, 8.2 KO, +5%, 4 W1108000-822‘W, SIP (10-pin)
R24Resistor, 56 KQ, +5%, 4 W110000-563,
R25Resistor, 12 KQ, 25%, 4 W110000-123Miscellaneous
J10zConnector, 8 Circuit, Header, .156 Ctr79-58334
R27Resistor, 43 KQ, 45%, 4 W110000-433Key 5
R28Resistor, 20 KQ, + 5%, 4 W110000-2033104,Connector, $0 Circuit, 4 Wall Header,—179186-001
B30Resistor, 39 KQ, 45%, 4 W410000-393JI05A,Rt 2 Rows
R31Resistor, 3300, 45%, 4 W110000-331J1058
.Jl07Connector, 6 Circuit, Header, .100 Ctr,179118006
R32Resistor, 2202, 45%, 4 W110000-221Key2
R33Resistor, 3.9 KQ, +5%, 4 W110000-392J108Connector, 11 Circuit, Header, .100 — 179118-011
R34Resistor, 10 KQ, +5%, 4 W110000-103,Cur, Key 2
R35Resistor, 20 KQ, +5%, 4 W110000-203

OP1-OP4 — Conn, 6 Ckt, Hds, .100 Cr 179177-606

R36Resistor, 43 KQ, +5%, 4 W110000-433OP3,OP4Conn, Rept,2Ckt179178-001
R37Resistor, 1 KQ, +5%, 4 W110000-102+5Vi,‘Test Point179051-002
R38Resistor, 10 KQ, +5%, 4 W110000-103+5V2,
R39Resistor, 27 KQ, 45%, 4 W4110000-273GND1,

GDN2

R40-R42Resistor, 10 KQ, + 5%, 4 W110000-103Socket, 16-Pin79-42C16
R43,Resistor, 15 KQ, 25%, 4 W110000-153Socket, 20-Pin79-42C20
R44Resistor, 1 KQ, +5%, 4 W110000-102Socket, 24-Pin79-42C24
R45Resistor, 27 KQ, +5%, 4 W110000-273Socket, 28-Pin79-42C28

Socket, 40-Pin 79-42C40

R46,Resistor, 1.8 KQ, +5%, 4 W110000-182
R47Resistor, 10 KQ, 45%, 4 W119000-103

5-24

Page 61

Road Blasters

N Illustrated Parts Lists

S

Page 62

Road Blasters Illustrated Parts Lists

Use these pads for C17-A& C18-A C18_C18-A

417 CL7-A

Use these pads for C17 & C18

Oy any design ot achcal information shawn theres nor any ng 0 Teprod

vendors of Atari Gamies Corporation, and for manufacivze under the corpeeali

NOTE: This illustration snows all parts required ‘or every version of this PCB assembly. Refer tc the parts. list on the opposite page fot actual parts used.

cotthe subject matter thereof, unless by writen agreement wilh or writen permission from the corparation.

Ibjecl matter ofthe drawang, feof, Except for manufacture by

Figure 5-9 Audio Ii PCB Assembly A043661-03 and -05 D

5-26

Page 63

Road Blasters. Illustrated Parts Lists

Audio II PCB Assembly Audio II PCB Assembly A0403661-03 D A043661-05 D Parts List Parts List

Desig- Desig-

natorDescriptionPart No.natorDescriptionPart No.

Capacitors Capacitors

€1,033300 wl, 25 V Radial Electrolvtic123003-338C1-C43300 wk 25 V Radial Electrolytic123003338

Capacitor - Capacitor

C7-C10,1 wE, 50 V Ceramic Capacitor122002-104C7-C12_—_.1 E50 V Ceramic Capacitor122002-104
cla|C13, C1422 wE 35 V Electrolytic Capacitor24-350226
cl422 a, 35 V Electrolytic Capacitor24-350226C15-C1822 pk 25 V Ceramic Capacitor122006-224
C1622 wR, 25 V Ceramic Capacitor122006-224,
9,€20001we S0Vic122002-102
CITA, CI8A22 pF, 25 V Ceramic Capacitor122006-224o i . osHs ave Ceramic Capicitori 008 04
C20001 #F, 50 V Ceramic Capacitor122002-102eens=on
22ii22002-
¢.1 E50 V Ceramic Capacitor1202-104Diodes
DiodesCRI-CR4_—Type-1N5401 DiodeALINS4O1
CRI-CR4—_‘Type-1N5401 Diode31-1N5401CR5-CRIO‘Type-1N4001 Diode31-IN4001

CR5-CR8._—_Type-1N4001 Diode 31-1N4001 Connectors

ConnectorsJACDCKey 6,9 Ckt., .15GInch Ctr. Header-179213-009
JACDCKey 6, 9 Ckt., .156nch Ctr, Header179213-009Connector;
ConnectorJAUXKey 6,9 Ckt,, .15Gdnch Ctr. Header1 79213-009
JAUXKey 6,9 Ckt., .156-Inch Cu. Header179213-009Connector
ConnectorJCDL2Ckt,, .15G4nch Ctr. Header179213-002
JCDL2CKt., .156-Inch Cte. Header Connector179213-002Connector
JSPK2Ckt., .156-Inch Ctr, Header Connector179213-002JsPKKey 3, 6 Ckt., .156-Inch Ctr. Header-179213-006

Connector Resistors

RB100, £5%, & W Resistor110000-100Integrated Circuits
RS22k, +5%, 4 W Resistor110000-223TypeTDA-20301-00
Ry3.3 kO, £5%, & W Resistor110000-332Q1.Q2TypeTDA-2035 Amplifier|
RII1KQ, +5%, & W Resistor110000-102Resistors
RB10, £5%, & W Resistori10000gi0RI10 k®, Dual Horizontal Pot Resistor11901 1-103
%RB10.2, +5%, % W Resistor110000-100
R1622k, +5%, % W Resistor110000-223-ia
RITOf, 25%. % W Resistor110005.001R4-R722 KO. +5%,W Resistor110000-223
uae:R8, RO10kQ, £5%, % W Resistor1 10000-103
Miscellaneousxo:>
Type-TDA-2030 Heat Sink178190-032RIO-RI11 kQ, +5%, 4 W Resistor110000-102
#6-32 x Yelnch Cross-Recessed72-1606R12,R13-1. Q, 45%, % W Resistor110000-010
Pan-Head ScrewRIT00, £5%, % W Resistor110005-004

#6-32 NuvWasher Assembly 75-99516 Miscellaneous

Thermal Compound78-1601SwiSPDT Miniature Slide Self-Test Switch69-004
Hot Melt Adhesive106006-001Type-TDA-2030 Heat Sink178190-032
Test Point179051-001#6-32 x 3/8-Inch Cross-Recessed72-16068

Pan-Head Screw #632 Nut/Washer Assembly 75.99516

Thermal Compound 78-1601 Hot Mek Adhesive 106006-001 Test Point 179051-001

ww ey a

Page 64

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 65

Road Blasters’

Coin Information and Game Statistics

Date:

Aux Coins Not used in Road Blasters game Left Coins Number of coins deposited in left coin mechanism Right Coins Number of coins deposited in right coin mechanism 1 Plyr Games _ Number of 1-player games Mins Played — Total time, in minutes, of all games played Mins Pwr Up —_ Total timie, in minutes, that the game has been turned on Aux Cntr 1 Highest rally achieved Aux Cntr 2 — Totai number of times add-a-coin used Aux Cntr 3 ——. Number of games without a new high-score entry Error Count Number of EEPROM errors Avg. Game Time Average game time in seconds (including add-a-coin continuation games)

Histogram Information

Length of Number of Games That Reached Level _ Game in Seconds 1 2 3 4 5

0-59 60-89 90-119 120-149 150-179 180-209 210-239 240-269 270-299 _ 300-329 330-359 = _ 360-389 390-419 420-449 450-479 480-509 510-539 540 &up -

High Score

Histogram Levels 1-3: Histogram Level 4: Histogram Level 5: Number of games that started at the Rookie, Veteran, or Expert level, respectively. These are only games that were played without using the game continuation feature. Number of games that ended on the original level for add-a-coin game continuation Number of games that ended on a higher level after a game continuation

Page 66

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 67

Cee Ge ene shipment. None of the Seller's other products or parts thereof are warranted. a ae Pac eiaue ae RCE Tae ales ae are returned to Bae dautagaeel ware y period, provided:

  • Seller is promptly notified in writing upon discovery by Buyer that said products are.

(©) Such products are retumed prepatd to Seller's plant; and

(©) Seller's examination discloses to Seller's satisfaction that such alleged repair, installation, or improper testing

defects existed and were not caused by accident, misuse, neglect, alteration, improper repair, installation, or improper testing. ye ‘no event shall Seller be liable for loss of profits, loss of use, incidental or consequential

‘any express warranty. ina written contract

Sere tereen nr ioe call purpose, and of. lien outa alors Beat ee reer

nor authorizes ‘person to assume for the Seller any

‘The use of any non-Atari parts may void your according to the terms of the warranty. Tie diet any neh c A para nay aso scvese atees me ea cl youre ace cause injury to you and others. Be very cautious in using non-Atari-supplied components et eee aes eee ete pe one nd oes ee oe ieee aie eh en eee including labor which is performed by such distributor.

Page 68

A

ATARI

GAMES

Atari Games Corporation 675 Sycamore PO. Box 361110 Milpitas, California 95035