Red Baron Sit-Down TM-171 1st Printing
Red Baron (revised hardware) (Atari, 1980) · Technical Manual · 60 pages · 36 sections · original scan

This page is a drawing, shown as the original scan.
MONITOR
GAME SERIAL # IDENTIFICATION TAG (OUTSIDE OF REAR DOOR)
REGULATORIAUDIO Il PCB:
RED BARON ANALOG———|j_ | VECTOR-GENERATOR PCB
RED BARON AUXILIARY PCB
GAME SERIAL NUMBER LOCATION Your game’s serial number is stamped on a plate on the outside of the game. The same number is also stamped on the chassis of the monitor, Regulator/Audio || PCB, Red Baron™ Analog Vector-Generator PCB, and the Auxiliary PCB. Please mention this number whenever calling your distributor for service.
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
Red Baron iSit-Down
Copyright © 1981 by Atari,Inc. All rights reserved.
No part of this publication may be reproduced by any mechanical}, photographic, or electronic process, or in the form of a phonographic recording, nor may it be stored in a retrieval system. transmitted, or otherwise copied for public or private use, without permission from the publisher.
Published by: ATARI INC. 1265 Borregas Avenue P.O, Box 427 Sunnyvale, Catifornia 94086
Lithographedinthe USA 3K
Red Baron ™/Sit-Down
Notice Regarding Non-Atari Parts
WARNING
Use of non-Atari parts or modifications of your Atari game circuitry may adversely affect the safety of your game, and may cause injury to you and your players.
Atari, Inc.'s warranty (printed on the inside back cover of this manual) may be voided, if you do any of the following:
1.) you substitute non-Atari parts in your coin-operated game, or
2.) you modify or alter any circuits in your Atari game by using kits or parts not supplied by Atari.
Not only may the use of any non-Atari parts void your warranty, but any such alteration may also adversely affect the safety of your game, and may cause injury to you and your players. .
Red Baron™/Sit-Down
Table of Contents
Location Setup A B. c. New Parts 0... eee eee ee Game tnspection . Game Installation. .....
- Voltage Selection ....... : : :
- Interlock and Power On/Off Switches ............-. 00.200. e eee Self-Test Procedure ... Option Switch Settings .
- Bonus Play Feature. .
- Coin Mechanism Multipliers
- Examples of Game Price Settings Game Play .........-.....--
- Attract Mode. ...
- Ready-to-Play Mode «6.6.6... eee tenes
- PlayMode..... ce ce tenet eee eee
- High Score Initial Mode .... 00.66. e eee ee
Maintenance and Repair A.
mmo Cleaning 0... eect e teers 16 Fuse Replacement... Opening the Control Pane! a
- LED Start-Switch Replacement .
- Joystick Maintenance and Repair . Monitor Removal .......... Printed-Circuit Board Removal . : Game Operation... 0.2. e nee 21
lilustrated Parts Lists Ilustrations and parts lisis begin on page .......--.... 00. e eee 26
Red Baron™/Sit-Down
List of Illustrations
Figure 1 Overviewof Game ....-.. 62.6 c ee eee tees 2 Figure 2 Installation Requirements .. . i 3 Figure 3 International Voltage Plug Selection . . : 4 Figure 4 Interlock and Power On/Off Switches ........... 5 Figure 5 Location of Self-Test Switch, Volume Control and Option Switches... 7
Figure 6 Self-Test Procedure... 2.20... oc eee eee 8 Figure 7 Game Option Settings . 10 Figure 8 Game Price Settings. . . 1 Figure 9 Coin Counter Option Settings . : . 13 Figure 10 Opening the Control Panel. .... 0.2.0... ec eee 16
Figure 11. Joystick Maintenance and Repair ............02.... 2000.2 eee ee 17 Figure 12 Monitor Removal ...........- : Figure 13 Printed-Circuit Board Removal Figure 14 Power Distribution . . : se Figure 15 Signal Distribution .. 2.2.2... 0. eee eee eee
{ustrated Parts Lists: Figure 16 Cabinet-Mounted Assemblies . . Figure 17 Control Panel Assembly....... Figure 18 Gimbal-Type Joystick Assembly . Figure 19 Regulator/Audio Il PCB Assembly 3: Figure 20 Red Baron™ Auxiliary PCB Assembly .............0.0. 0.2020 34
Figure 21. Red Baron™ Analog Vector-Generator PCB Assembly.............- 37 Figure 22 Power Supply Assemblies forX-Y Games ..........0...20-0-00 00s 42 Figure 23 Double Coin Acceptor/Mount Assembly ................020200 005 44
Red Baron™/Sit-Down
WEST and CENTRAL U.S.A. Parts for all Atari customers in the U.S.A. Game sales and service
Ataii, Inc. California Customer Service Office 1105 N. Fair Oaks Avenue P.O. Box 427, Sunnyvale, CA 94086 Telex 17-1103 (Monday-Friday, 7:30-4:00 pm Pacific Time) expe From California, Alaska or Hawaii (408) 745-2900 = From anywhere else in this area © ‘toll-free (800) 538-1611
EAST U.S.A. Game sales and service only
Atari, inc New Jersey Customer Service Office Cottontail Lane, Somerset, NJ 08873 Telex 37-9347 (Monday-Friday, 7:30-4:00 pm Eastern time) ae From New Jersey (201) 469-5993 eee From anywhere else in this area iollfree (800) 526-3849
EUROPE Parts for all Atari customers in Western Europe. Game sales and service
Atari treland Limited European Customer Service Office TIPPERARY TOWN, Tipperary Town, Ireland IRELAND Telex 8165 (Monday-Friday, 9:00-6:00 pm GMT)
@ 06252155
vi
Location Setup <>
>
A. New Features
The Red Baron™/Sit-Down game has five new features. Even if you are familiar with Atari garnes, you should note these important differences. The new features are: @ Gimbal-Type Joystick Control. This new heavyduty control provides a realistic simulation of an aircraft contro}. The X- and Y-direction motions are measured by two potentiometers mounted on this control. @ Red Baron includes a newly designed power supply assembly. This power supply has alarger transformer to handle the increased power requirements of the expanded game circuitry. @ Red Baron’s new sit-down cabinet design provides a total environment for players. Despite its arcade size, the game is easily moved by one person, due to its swivel casters. All three PCBs are very easily accessible; they are mounted on the inside of the hinged rear door. @ Game Circuitry. Atari's 3-dimensional X-Y game circuitry has been expanded into two interconnected printed-circuit boards (PCBs)—the Red Baron Analog Vector-Generator and the Auxiliary PCBs. The circuitry produces more lines on the
These new parts, as well as all other major parts in the game, are illustrated in Figure 1. Throughout this manual, wherever one of these new parts is a) mentioned, you will see this symbol:
Red Baron™)Sit-Down
On REGULATOR’ AUDIO II PCB
AUXILIARY PCB
ANALOG VECTOR. GENERATOR PCB
MONITOR SHIELD
GIMBAL-TYPE JOYSTICK CONTROL
FRONT WINDOW
UTILITY COIN SWITCH
REAR ACCESS DOOR
FRONT ACCESS DOOR
DOUBLE COIN ACCEPTOR
Figure 1 Overview of Game
B. Game Inspection
This new game is ready to play upon removal from the shipping carton. However, your careful inspection is needed to supply the final touch of quality contro}. Please follow these steps to help us insure that your new game was delivered to you in good condition.
[orem NOTE remy Do not plug the game in yet!
- Examine the exterior of the game cabinet for dents, chips, or broken parts.
- Remove the two screws that were used as extra security to seal the rear access door. (During shipment these screws help reduce vibration of the PCB components on the door.) Unlock and open this access door, as well as the small front access door; inspect the interior of the game as follows: @ Check that all plug-in connectors (on the game harness) are firmly seated. Replug any connectors found unplugged. DON'T FORCE CONNECTORS TOGETHER. The connectors are keyed so they only go on in the proper orientation. A reversed edge connector will damage a PCB and will void your warranty. @ = =Check that all plug-in integrated circuits on the Red Baron™ Analog Vector-Generator PCB are firmly seated in their sockets. @ Remove the tie-wrap that holds the coiled power cord on the inside cabinet wall. Check the cord for any cuts or dents in the insulation. Place the Square black metal Strain-relief plate in the wood slot at the bottom of the rear door opening.
@ Note the location of the game’s serial number—it is printed on the special label on the outside of the game cabinet. Verify that the serial numbers also stamped on Red Baron ™/Sit-Down
the Red Baron Analog Vector-Generator PCB, Auxiliary PCB, Regulator/Audio II PCB and monitor are ali identical. A drawing of the serial numbered components is on the inside front cover of this manual. Please mention this number whenever you call your distributor for service. @ Check all major subassemblies such as the power supply, joystick control, and monitor for secure mounting.
- Remove the game from the pallet. Roll the game to its final location. Now tilt it slightly onto one side and partly unscrew the two cabinet-leveling legs that are off the floor. Lower the game and tilt it onto the other side; unscrew those two legs. You may have to do some adjustment to level the cabinet.
Cc. Game Installation
Figure 2 Installation Requirements
Power 263 watts maximum Temperature 0 to 38°C (32 to 100°F) Humidity Not over 95% relative Space Required 66 x 1642 cm (26 x 64% in.) Game Height 152¥2 cm (60 in.)
- Voltage Selection This game has two possible power supplies: the domestic or international power supply. The domestic power supply operates on one line voltage range: 105 to 135 VAC. The international power supply has four colored voltage selection plugs and operates on the line voltage of almost any country in the world.
Before plugging in your game, check your power supply. If the supply doesn’t have voltage selection Plugs and a connector at J3 (see Figure 3), then the game operates on any voltage from 105 to 135 VAC. \f the supply has the colored voltage selection plugs, make sure that the voltage selection plug on the power supply is correct for your location's line voltage. Check the wire color on the plug and see if it is correct per Figure 3.
Red Baron'M/Si-Down
- Interlock and Power On/Off Switches To minimize the hazard of electrical shock while working on the inside of the game cabinet, two interlock switches have been installed (see Figure 4). One is located behind the rear access door and one is behind the small front access door. These switches remove all AC line power from the game circuitry when either door is opened.
Check for proper operation of the interlock switches by pertorming the following steps: © Be sure the front and rear access doors are closed. @ Plug the AC line power cord into an AC outlet. Set the power on/off switch to the “on” position. Within 30 seconds the monitor should display a picture. Stowly open the rear access door. The monitor piciure should disappear when the door is opened approximately 2.5 cm (1 inch), Close and lock this door and repeat this step with the small front access door. If the results of the preceding step are satisfactory, the interlock switches are operating properly. If the monitor doesn’t go off as described, check to see if the corresponding interlock switch is broken from its mounting or stuck in the “on” position.
=
Fuse cover must be in place during game operation.
Figure 3 Line Voltage Range Plug Color 90.110 VAC (100) Violet 105-135 VAC (120) Yellow 200-240 VAC (220) Bive 220-260 VAC (240) Brown
International Voltage Plug Selection
Red Baron ™/Sit-Down
SAFETY INTERLOCK SWITCH ‘SWITCH
ON
POWER ON/OFF SWITCH
Figure 4 Interlock and Power On/Off Switches
Red Baron™/Sit-Down
D. Self-Test Procedure
This game will test itself and provide data to demonstrate that the game’s circuitry and controls are operating properly. The data is provided on the monitor, the light-emitting diode in the start switch, and the game speaker; no additional equipment is necessary.
Part of the self-test procedure includes a display of the operator-selectable game options. Therefore, we Suggest you run the self-tesi procedure anytime you need to change the game’s options.
To run the self-test, follow the instructions outlined in Figure 6.
Red Baron /Sit-Down,
RED BARON ANALOG VECTOR.GENERATOR PCB
rd \ OPERATOR OPTION OFF SS SWITCHES ate (OLUME INCREASE: On fy ~ SELF-TEST =. oo TURN CLOCKWISE SWITCH s ss i
Figure 5 Location of Self-Test Switch,
Volume Control and Option Switches
Red Baron™/Sit-Down
Figure 6 Self-Test Procedure
Results if Instruction Test Passes Results if Test Fails
- Setselftest. After about 1012 sec- RAM FAILURE is indicated by a sequence of 1 to 10 tones. You will hear a short low tone switch to on position —onds, the monitor and a short flash on the LED start pushbutton for each good RAM chip, and a long (see Figure 5). displays the picture high tone accompanied by a long pulse on the start pushbutton for a failing RAM chip. below. No sounds are The test stops with the first failing RAM-chip pair (example: J2 and H2 are a pair). To produced. restart the sequence, press the reset pushbutton on the Red Baron™ Analog Vector- Generator PCB, or set the self-test switch to off, then again to the on position. Identify the bad 8AM chip with the table below. Exampte: four short low tones followed by a Jong high tone indicates failure of RAM at location B2. Bad RAM Chip Location Long High Tone: ‘on Anaiog Vector-Generator PCB: Ast J2 2nd H2
3rd A2 ath Al
Sth B2 eth Bt 7th C2 eth Ct
9th p2 10th o1
ROM/PROM FAILURE is indicated by two columns of numbers on the left side of the screen. The number in the left column indicates the location of the failing ROM/- AVERAGE PROM(s). Identify the bad ROM/PROM with the table immediately below. GAME TIME IN SECONDS Ignore the hexadecimal numbers in the right column on the screen.
LEFT COIN MECH RIGHT COIN MECH Dispiayed No.: Bad PROM Chip Location: _PrintedCircuit Board: MULTIPLIER MULTIPLIER: Q BIC3 or F/H3* 1 AS or E3 2 i=}
SWITCH SWITCH 3 mm Analog Vector:
TOGGLE 4 4 a Generator PCB
6 M1 7 Ni 3 axe 9 corr Auxifiary PCB “If this PROM is bad, you will hear a continuous low tone, and the program may be unable to display a screen image. **If this PROM is bad, self-test will not work (screen may be blank or may display “garbage"’). . It you replace this part, you must erase this ROM before locking up the game (see instruction 5 in this self-test procedure). Otherwise the self-test will continue to display 9.
MATH BOX FAILURE is indicated by a single letter displayed in the upper right corner DISPLAY CHARA Of the dispiay. Math-box failure is explained in the Signature Analysis Procedure, on the Red Baron™ schematic Sheet 1, Side B. Identify the failure with the table below.
Displayed Leiter Failure T Time out error H Data ertor—high byte PHOTO ABOVE SHOWS L Data error—low byte AN EXAMPLE ONLY
[Selt-test is continued on next pagel
Instruction Red Baron™/Sit-Dowa
Figure 6 Self-Test Procedure, continued
Results if Test Passes Results if Test Fails
- Activate start switch, fire switch, slam switch, and utility and coin switches.”
- Move joystick forward and backward.
- Move joystick to the right and left. As switch activates, you'll hear a beep. As Switch deactivates, you'll hear another beep.
The tower left number ‘on the screen will increase with backward Motion, and decrease with forward motion. (ignore any flickering of numbers}
The lower right number on the screen will increase with rightward motion, and decrease with leftward motion.
- Erasing the High Score Table (optional) The current three highest scores are held in permanent memory, even if the game is unplugged. If you want to erase these scores, simultaneously press the start and fire buttons. The ERASING message at the center right of the screen will then be displayed for several seconds, until the entire tabie is erased. The average game time data will also be erased.
- When satisfied with test, set selftest switch to off position. You will not hear a beep for the defective switch.
Incorrect progression of numbers indicates potentiometer harness wires were connected incorrectly. No number displayed indicates potentiometer is bad or harness wires are loose.
“Activate coin switches by inserting at least one coin in each coin slot. You wili not trip the coin counters as tong as you are in self-test.
Red Baron ™/Sit-Down
E. Option Switch Settings
- Bonus Play Feature The program in Red Baron™ offers a bonus play for certain combinations of coins inserted. This bonus feature is operator-selectable, meaning you may choose to offer it or not.
For exampie, with your game set at 50¢ per play, players who deposit four successive quarters or a $1.00 coin, then press the start button, will receive a bonus play. Therefore, players receive 3 plays for $1.00.
This bonus feature encourages players to insert more money than just the minimum 50¢ you could require for one game. Various other bonuses are available (see Figure 8).
- Coin Mechanism Multipliers The Atari coin acceptor mount for this game is available with about a dozen different mechanisms. You may have both mechanisms accept the same or different denominations. Regardless of the type of mechanism you install, you must Correctly set the “muitipliers’ for each mech on the game PCB. The multipliers determine how much each mechanism will be worth to the game’s logic.
The basic unit of measurement is 25¢, which equals a multiplier of x1. Therefore, if you have a 25¢/$1 coin acceptor, you will probably want to set the left and right option-switch multipliers at x 1x 4.
You can Set these multipliers with toggles 3 thru5 on the Red Baron™ PCB switch assembly at location M10. For exact settings of these toggles, reter to Figure 8.
- Examples of Game
Price Settings
Figure 8 explains the options, giving twelve examples of the most common U.S. situations. The toggles mentioned are ail in the switch at location M10; they only relate to game price, coin mechanism multipliers, and the bonus credit for multiple quarters or the $1.00 coin. You should set the toggies relating to other functions as you see fit, although Figures 7, 8, and 9 provide “$” signs indicating Atari’s recommendations.
Figure 7 Game Option Settings
When changing the options, verity proper results on the monitor display by performing the self-test. Note that changing an option on any of the following eight toggles will cause an immediate change on the monitor screen during the self-test. To change toggie positions on the switch assemblies, you need not remove the game PCB. The switches, usuaily colored blue, are easily accessible when the Red Baron™ Analog Vector-Generator PCB is mounted in place.
Toggle Settings of 8 Toggle Switch on Red Baron PCB (at P10) {TOP switch when PCB is in game) 8 7 6 5 4 3 2 1 Option
Off ott On
Off Off
Off On On Off On On Off off Off On On Off
Off
Ott On Ort English $ On Spanish . ott French On German
Bonus airplane granted at: 2,000, 10,000 and 30,000 points 4,000, 15,000 and 40,000 points $ 6,000, 20,000 and 50,000 points No tonus airplanes 2 airplanes per game Jairplanes per game $ 4 airptanes per game 5 airplanes per game 1-play minimum $ 2-play minimum Selt.adjusting game difficulty feature turned off Self-adjusting game difficuity feature turned on $
$ Manufacturer's suggested settings
Red Baron™/Sit-Down
Figure 7 Game Option Settings, continued x Airplanes per game:
| 2 | 3 | 4 | 5 |
It self-adjusting game difficulty feature is Bonus airplane granted at:
| turned on, the program strives to maintain the | 2,000, 10,000 and 30,000 points | 90 | 105 | 420 | 435 |
| following average game lengths (in seconds} | 4,000, 15,000 and 40,000 points | 6 | g9e$ | 105 | 120 |
| 6,000, 20,000 and 50,000 points | 60 | 75 | 90. | 105 | |
| No bonus airplanes | 45 | 60 | 75 | 90, |
$ Manufacturer's suggested settings
Figure 8 Game Price Settings The white block below contains Atari’s suggested settings. All numbers 1 thru 8 are toggle seitings on the 8-toggle switch at location M10, on the Red Baron™ Analog Vector-Generator PCB (the CENTER swiich assembly),
50¢ PER PLAY:
Bonus No bonus $1.00 = 3 plays
| 8 | 7 | 6 | |
| Straight | of | Off | off |
25t Mechs (1)
| 4 | 3 | 2 |
| Off | Off | On |
25¢1$1.00 Mechs
25¢ PER PLAY: Bonus No bonus $.50 = 3 plays
Straight Of
25¢ Mechs ee (Off On
| 7 | Te | 5. | |||
| 25¢/$1,00 | Off On | Off | On. | OH | Off. |
| a2 | a. | ge | 3 | Bey | |
| On | On... Off | Of On | On. Off |
Circled numbers refer to game pricing labels you should use with each situation (labels are illustrated on following page).
YW
Red Baron™/Sit-Down
Figure 8 Game Price Settings, continued For your information, we have defined below the switch setlings for thase options relating to game price, coin mechanism multipliers, and bosus play. This information is useful in case you need to temporarily set the Red Baron™ game on free play, or if you have German coin mechanisms in your door.
Toggle Settings of 8-Toggle Switch on Red Baron PCB (at M10). CENTER switch when PCB is in game 8 7 6 5 4 3 2 1 Option
Off Off On On
Off Off On On Ott On Off On
Off On
Off
Off oft
Off
Off On Off Cn On On Off Off
On Off Off On Off On Free play 1 coin® for 2 plays 1 coin” tor 1 play 2coins* fort play $ Right coinmech x 1 $ Right coin mech x 4 Right coin mech x 5 Right coin mech x 6 Left coinmech x 1 § Lefi coin mech x 2
No bonus coins $
For every 2 coins” inserted, game logic adds 1 more coin*
For every 4 coins” inserted, game logic adds 1 more coin* For every 4 coins” inserted, game iogic adds 2 more coins” For every 5 coins” inserted, game logic adds 1 more coin* For every 3 coins” inserted, game logic adds 1 more coin*
"in the U.S., a “coin” is defined as 25¢. In Germany a “coin” is 1 DM.
$ Manutacturer's suggested settings
To achieve bonus plays, ail coins must be inserted before pressing start button.
C , @@ 2 coins =1 play ATAR J
ne? ATARI @ 1 coin = 1 play
AO @@ 2 coins =1 play ATARI
@ ee r: ) 4 coins = 3 plays Ke @@ 2 coins Am @@@ 3 coins 008 @ 4 coins
@@ 2 coins =1 play @ $1 coin=3 plays (Susan B. Anthony coin) ° AL ATAR!
oO, @ icoin = 1 play
anki 2 play minimum (2 coins = 2 plays)
(For operator use—write in the appropriate phrase. Use a permanent-ink water-resistant marker.)
Red Baron™/Sit-Down
Figure 9 Coin Counter Option Settings
[These toggles determine which coin mechanisms activate which counters]
Toggle Settings of 4-Toggle Switch on Game PCB (L11)
| 4 | 3 | 4 | 1 |
Two coin acceptors in the coin door: Two coin acceptors and a pushbutton utility coin switch in the game: Three coin acceptors in the coin door:
| On | On | Both acceptors activate all coin |
counters simultaneously.
| Off | On | Both acceptors activate 2 count- |
| p> | 8 | ers separately. |
3 8 ed 3.3
| & | 2 | on | ot | Both acceptors activate all coin |
counters simultaneously.
| Off | Off | Both acceptors activate 2 count- |
ers separately, Do not use this setting.
Do not use this setting.
Utility coin switch will not activate a coin counter, if you do not hook up a separate counter. Both acceptors activate both coin counters simultaneously.
Utility Coin switch will not activate a coin counter, if you do not hook up a separate counter. Left and right acceptors activate 2 coin counters separately. $ All 3 are same denomination and they activate all coin counters simultaneously.
Left and center acceptor activate ‘one coin counter; right acceptor activates another coin counter.
Left acceptor activates one coin counter; center and right acceptor activate another coin counter. Not for any currently designed 3-mech coin door.
Left, center and right acceptors activate 3 coin counters separately.
$ Manufacturer's suggested setting
F. Game Play
Atari’s Red Baron™ game is a one-player game with an X-Y or vector-generator monitor. The game depicts a first-person’s view from a World War | biplane cockpit. The player’s goal is to destroy as many enemy biplanes, blimps, tanks, pillboxes, pyramids and buildings as possible.
Players can maneuver their airplanes with the joystick control. Moving the joystick in its four directions creates a sensation of diving, climbing, or banking to the left or right.
The game has five possible modes of operation: Attract, Ready-to-Play, Play, High Score Initial, and Self-Test. Self-test is a special mode for checking the game switches and computer functions. You may enter this mode at any time. When entered, all game credits are cancelled.
- Attract Mode
The attract mode begins when power is applied to the unit, after a play or high score initial mode. or after self-test. This mode is continuous and is only interrupted when a play is paid for and accepted or when in self-test. In this mode, the monitor displays three possible pictures. One of the pictures displays a typical game play sequence, with a view looking out of the airplane cockpit at the horizon and mountains below. The player's propellor is almost always visible at the center bottom of the screen during this phase.
Enemy biplanes swoop towards the player's airplane and eventually overtake it. The VALUE message at the top center of the screen indicates the current number of points a player can earn for shooting the enemy biplane. The value ranges from 70 to 300 points, and decreases as the enemy plane comes closer to the player.
Blimps also appear in this scene. The blimps, tanks, and pillboxes may be firing shells at the player. If hit, the player sees a bullet picture on the windshield, and the scenery spins around, indicating that the player has crashed.
The second picture disptayed during this mode will only appear if no credits remain in the game. The screen shows the RED BARON banner pulled by a plane traveling towards the left. The propellor usually at the bottom of the screen disappears during this phase.
Red Baron /Sit-own
The third picture shows the three to seven highest scores and their matching initials. If you erase the special ‘‘permanent” memory (see Figure 6, Self-Test Procedure), then this table will not appear on the screen. The table is redeveloped from scores of subsequent games.
- Ready-to-Play Mode This mode begins when sufficient coins are accepted for a game. It ends when the START pushbutton is pressed. When this mode begins, the message PRESS START flashes in the center of the screen. The displayed pictures are otherwise the same as those shown in the attract mode.
Operators may choose one- or two-play minimums by selecting one of the option switch settings on the game PCB (see Figure 7, Game Option Settings). If you select the two-play minimum and a player inserts enough money for only one play, the message 2 PLAYS MINIMUM flashes on the screen until the required number of coins is inserted.
- Play Mode The play mode begins when the start pushbutton is pressed. The mode ends when the player’s last airplane is lost.
Players can score various points for shooting the differeni objects; the point values for each are silkscreened on the control panel. As mentioned earlier in Section 1, Attract Mode, the value for enemy planes can vary. Point values for all other objects remain fixed.
The game starts with a slow enemy biplane appearing on the screen; the first four planes are relatively passive. As game time progresses, the Player's biplane speed increases and the enemy planes become more evasive. After four airplane “attacks”, the player will see various objects on the ground. Later on, to provide challenge, the tanks, pillboxes, and blimps will start shooting at the player. If the player gets a very high score, the planes themselves will finally start shooting at the player.
One of the new operator-selectable features of Red Baron™ is its self-adjusting game difficulty. Figure 7 shows the option switch settings that determine an average game time in seconds. During self-test, the monitor displays the player’s average game time in seconds.
The game program accumulates an average of the last 32 games’ lengths. If the accumulated average exceeds the operator-selected average, at the beginning of the next game the computer makes the play harder. The logic does so by increasing the speed of the player's airplane and enemy airplanes. In essence, this feature adjusts the difficulty to establish a consistent average game time.
The average is stored in the non-volatile memory—as are the top three scores on the high score table. Therefore, if you select this game difficulty option, you need not worry that the average will be “dost” if you turn off the game each night.
- High Score Initial Mode At the beginning of this mode, player instructions appear near the upper center of the screen, and A____ appears below them. Players enter initials one character at a timex
Pressing the fire button a third time causes the initials and game score to transfer to the high score table. This table contains a maximum of seven scores and appears during the attract and ready-toplay modes.
Maintenance and Kepair =
All games require certain maintenance to keep them in good working order. Clean, properly maintained games will attract players and earn more profits.
The most important maintenance item is running the seli-test every time you collect money from the coin box. Just looking at a game will not tell you if the gimbal-type joystick control or light-emittingdiode switch is broken, or if the LED has burned out. The self-test will inform you of any of these possible problems. 4 A 7 | Ao wi Second, you should regularly clean the outside of the game and the coin mechanisms. In addition, you will need to regularly lubricate the joystick control— for details see Section C, Part 2. WS K
Red Baron ™/Sit-Down
A. Cleaning
The exterior of the game cabinet and the metal and acrylic surfaces may be cleaned with any nonabrasive household cleaner. !f desired, special coin machine cleaners that leave no residue can be obtained from your distributor. Do not dry-wipe any of the acrylic paneis, because dust can scratch the surface and result in fogging the plastic.
Bb. Fuse
Replacement
This game contains five fuses—all on the power supply assembiy (not including the monitor fuses). Replace fuses only with ihe same type as listed in Figure 22 of this manual. See the Electrohome Quadrascan™ X-Y monitor manual (TM-146) or the Wells-Gardner monitor manual (TM-164) for the monitor fuse data.
C. Opening the Control Panel
Prior to repairing or replacing any item on the control panel, unplug the game. Then open the rear access door. Reach underneath the monitor (above the speaker) and remove both sets of carriage bolts, wing nuts, flat and lock washers, located on the underside of the control panel (see Figure 10). Walk around to the player’s seat, lift up on the control panel, and tilt it towards you.
- LED Start Switch Replacement The light-emitting diode (LED) switch on the control panel has a very low failure rate. In case the switch should ever be suspect, first test it per the description that follows. To replace the switch, refer to Figure 10.
@ Remove the wires from the suspected switch. @ Set multimeter to ohms scale. Set ohms scale to Rx 1, then zero the meter. @ Connect multimeter leads to appropriate LED switch contacts (see Figure 10 for designation of switch contacts and meter lead placement). @ Check contacts (push and release the switch button) for closed and open continuity. @ = \fthe contacts do not operate sharply or always remain closed or open, then replace the LED switch as outlined in the figure.
To remove LED switch: @ Remove all wires from the faulty switch. © Turn the switch counterclockwise (as viewed from inside of control panel) while holding the black cone-shaped nut on the outside of the control panel. ® Install a new switch using the reverse procedure. @ Reconnect the hamess wires.
NORMALLY CLOSED (N.C.) CONTACT
NORMALLY OPEN (N.O.) CONTACT
» LIGHT-EMITTING-DIODE COMMON {L.E.0) CONTACTS CONTACT
Figure 10 Opening the Control Panel
“>
- Joystick Maintenance and Repair
Normal maintenance involves lubricating four parts in the joystick control approximately every six months (this requires removing the control). First open the control panel as described previously. Then unplug the “quick-disconnect” connectors on the two potentiometers, as well as the connector for the fire switch.
From the inside of the control panel, remove the four flat and lock washers, hex nuts and carriage bolts that mount the joystick onto the control panel.
Then open up the joystick control assembly by removing the four flat washers, hex nuts, and long screws (See Figure 11). At this point, most of the parts should become disassembled.
For lubrication, use only Nyogel 779 lubricant {Atari part no. 178027-001). Lubricate the following parts inside the control: Red Baron™/Sit-Down
@ The bail pinned to the shaft and the ends of the pivot pins that protrude from the ball. @ The insides of the two black linkages, located on the potentiometer shafts. © The insides of the two gimbals, where the bottom of the shaft wears against them. @ The four holes on the sides of the pivot ball housings, where the gimbals are attached.
To replace the bellows, remove both gimbals and the bellows cap. Slide the bellows off the bottom of the shaft and over the harness wires. Slide the new bellows up over the harness and shaft.
Reassembie the joystick control, and then reinstall it in the control panel. Reconnect the harness wires as shown in the following diagram: make sure the right colors go to the tabs on the potentiometers and the fire switch.
Repairs on the control handle would probably only involve replacement of potentiometers, the fire switch or the centering bellows.
LED { ORANGE CONTACTS | RED,
‘START SWITCH BLACK TO COMMON FIRE SWITCH { YELLOW TO N.O. HARNESS | GREEN TO GROUND
BLACK | HORIZONTAL Rep | POTENTIOMETER
VERTICAL BLUE POTENTIOMETER BLACK
RED
Figure 11 Joystick Maintenance and Repair
Red Baron™/Sit-Down
PIVOT PIN — POTENTIOMETER
LUBRICATE HERI PIVOT BALL HOUSINGS
LUBRICATE HERE (4 PLACES) oO
CENTERING BELLOWS
BELLOWS CAP
INNER GIMBAL ae S OUTER GIMBAL
Figure 11 Joystick Maintenance and Repair, continued
Red Baron ™sit-0own
D. Monitor Kemoval
If you should need to remove the Quadrascan™ XY monitor, follow steps 1 thru 3 as listed on this page. Refer to Figure 12. A WARNING High voltages may exist in any television monitor, even with power disconnected. Use extreme caution and do not touch electrica! parts of the yoke area with your hands or with metal objects in your hands! If you drop the monitor and it breaks, it will implode! Shattered giass and the yoke can fly 6 feet or more from the implosion. Use care when replacing any monitor.
- Be sure the game is unplugged from its wall outlet! Open the rear access door and unplug the monitor harness connector—it is easily accessible right behind monitor.
- Remove the four sets of carriage bolts, flat and split lock washers, and hex nuts that hold down the metal chassis of the monitor.
- Carefully slide the monitor chassis out the back of the game.
Disassemble in the order indicated. (Circled numbers match the steps above.)
Figure 12 Monitor Removal
Red Baron ™/Sit-Down
E. Printed-Circuit Board Kemoval
You may wish to remove the Red Baron™ Analog Vector-Generator printed-circuit board (PCB), Auxiliary PCB or the Regulator/Audio 1! PCB for service or inspection. To do this, refer to Figure 13 and proceed as follows:
1. 2. Open the rear access door. Locate the securing screws and fiber washers that hold down the PCB in its slots, and remove them. (Each PCB has two sets of this fastening hardware.) If you are removing the Analog Vector-Generator or Auxiliary PCB, first remove the two tie wraps that fasten the edge connector to either PCB. Then unplug the edge connector. If you are removing the Regulator/Audio Il PCB, simply disconnect the five small harness connectors on this board. Carefully slide the PCB straight out of its slots and towards your left. Be careful not to twist the board, as this may loosen connections or components. Replace or repair as required. Reinstall the PCB, making sure that the connectors are properly plugged in. Note that they are keyed to fit on only one way, So if they don’t slip on easily, don’t force them! A reversed connector will probably damage the PCB and will void the warranty. Replace the securing screws and fiber washers in the PCB. Reinstall the tie-wraps used to secure the edge connectors to the PCBs. Close and tock the rear access door. Check that the operation of the game is correct and perform the self-test. This is especially important with any game when you replace a PCB. Normaily the only adjustments on this game are option switch changes (made on the 4- or 8-toggle DIP switches). Unless you are a qualified technician, do not turn any of the knobs near the Analog Vector-Generator PCB’s lower right corner. Also do not turn the small knobs on the Regulator/Audio |i PCB.
REGULATOR: AUDIO Il PCB
RED BARON AUXILIARY PCB
RED BARON ANALOG VECTOR- GENERATOR PCB
Figure 13 Printed-Circuit Board Removal
F. Game Operation
With this manual you received three large sheets that contain the wiring and schematic diagrams for the Red Baron™Sit-Down game. Sheet 1, Side A, includes information that shows the arrangement of these diagrams. These diagrams include information that explains the functions of the circuits and defines inputs and outputs.
Atari's Red Baron is a microprocessor-controiled game. The microprocessor is contained on the Analog Vector-Generator PCB. This board receives switch and potentiometer inputs from the control panel and coin acceptors. These inputs are processed by the Analog Vector-Generator PCB and output to the monitor, Regulator/Audio II PCB, and control panel.
The monitor is an X-Y monitor. Therefore, the monitor receives signals for the X, Y and Z axes. Since the location of the beam in the monitor is totally controlled by the X- and Y-axis outputs of the Analog Vector-Generator PCB, this board does not contain a standard sync circuit. The X- and Y-axis inputs to the monitor step in increments of 1024 steps for the X (horizontal) axis, and 768 steps for the Y (vertical) axis. The Z axis merely controls the intensity of the beam. Red Baron ™/Sit Down
The Regulator/Audio Il PCB performs two functions: 1) it regulates the voltages from the power supply to +5 VDC and + 12 VDC, and 2) it amplifies the audio output from the Auxiliary PCB.
Specifically, the +5 VDC from the Regulatori- Audio Il PCB provides mosi logic power to the Anatog Vector-Generator and Auxiliary PCBs, + 22 VDC is regulated on the Analog Vector-Generator PCB to produce +15 and +5 VDC (the latter for the digitalto-analog converters), and + 22 VDC provides power tor the audio output of the Auxiliary PCB. The audio output from the RegulatoriAudio !| PCB directly drives the game speaker and is controlled by the volume control, mounted inside the small front access door.
The Power Supply is the source of all voltages in the game. These voltages are protected by four fuses in the fuse block on the power supply chassis. The primary winding of the power supply transformer is protecied by the cartridge-type fuse in the Power supply chassis.
Figure 14 illustrates the distribution of power in this game. Figure 15 illustrates the distribution of signals.
Red Baron™/Sit-Down
SAFETY INTERLOCK SWITCH
MONITOR CONTROL PANEL SAFETY INTERLOCK ONOFE SWITCH SWITCH
REGULATOR/AUDIO II PCB AUXILIARY PCB
= \| COIN ACCEPTORS
©
+ 12VDC +5v0C -s vDC +22 VDC -22 yDC How +5 VOC
10.6 VAC 36 VAC 6OVAC 6.1VAC
ANALOG VECTOR. 4
GENERATOR PCB eS
POWER CORD POWER SUPPLY
Figure 14 Power Distribution
Red Baron™/Sit-Down
CONTROL PANEL
UTILITY SWITCH, VOLUME CONTROL MONITOR & SELF-TEST SWITCH
AUXILIARY PCB
COIN ACCEPTORS REGULATORIAUDIO II PCB ¢ SPEAKER eon
- A COUNTER —— ae
SPEAKER 182
ANALOG VECTOR- GENERATOR PCB
Figure 15 Signal Distribution
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
IHlustrated
Parts Lists
This chapter provides you with the necessary information for ordering replacement parts for your Red Baron™/Sit-Down game. Please note that, for simplicity, common hardware has been deleted from most of these parts lists. This includes screws, nuts, washers, bolts, etc.
The paris lists are arranged in alphanumeric order. For example, all “A-” prefix numbers come first. Following this are numbers in sequence evaluated up to the hyphen, namely 00- thru 99-, then 000598- thru approximately 190000-.
When ordering parts from your distributor, give the part number, part name, applicable figure number of this manual, and serial number of your game. This will help to avoid confusion and mistakes in your order. We hope the results will be less downtime and more profit from your game.
Hed Baron'"/Sit-Down
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL “Reproduction forbidden without the specific written permission of Atari, Inc., Sunnyvale, CA This drawing 15. only condshanally’ issued, and neither NGF Possession thereo! conlers or iransters any for Ficense to use. tne subject matter of the draw. ing or Baw design 0: technical nformation shown tereon, not any tight to reproduce this Grawing or any part thereot. Except for manufacture by vendors of Atari, Inc., an¢ for manutacture under the corporation's. wiilten license, ng rignt to veprouuce this drawing 1s granted or tne subject matter thereo! uniess by written agreement with oF mitten permission trem the corporation
naan " 92-047 or 92.050 (Monitor) A036992.01 0357.45.03 (Main Hamess) (101. PCB Retaines)
Regul/Audio ll PCB— see Figure 19
03707401 — (Rear Door) =
Auxiliary PCB— see Figure 20
A036247-01 {PCB Interconnecior)
71-2110 Lock)
034536-03 pr. Damper) “ P 48-009 (Speaker)
Analog Vect-Gener. PCB— see Figure 21 005419-01 Gilley C y 00999201. 035745.02 NS (OnOrt Sw. Cover) (18n. PCB Retainer) Power Supply Assy. — tame i rig A034841-08, see Figure 22 ) apenas 006450.01 or A035989-08 Ono ba (Power Cord) Mounting Plate)
Figure 16 Cabinet-Mounted Assemblies A037051-xx B
Red Baron™/SitDown
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL Benraduction torbigden without the specific entten permission of Atan, Inc., Sunnysaie, CB. jonally’ sssued, and neither recaipt nar possession {reveal conters or Wansters any ight in, oF license to use. the subject matter of the drawing oF any design or technscai information shown thereon, for any night te reproduce this drawing or any pari thereol. Except for manuiaciure by verdors of Atan, Inc.. and for manufacture under the corporation's written license, a0 right to reproduce this drawing is glanted or ihe subject mater thereo! uniess by written agreement 035465.01 with or writien permission from the Gerporation (Mon, Bez0!) ' 037086-01 (Retainer) 037090-01 (Overlay) 002728.01 (Ctrl Pri. Brkt} 037087-01 (Front Window) 035462.01 (Mon. Shield) 69.001 (Self-Test Sw.) Joystick Assy.— see Figure 18 ‘A036320-01 (Wol!Self-TestiCoin Assy.)
19-9032 037095-91 (Vol, Ctrl.) (Cowling)
62-0414 (Coin Sw.) Control-Panel Assy.— see Figure 17
007882-02 (inierl, Sw. Cover)
A036189-01 037083-01 (inter). Sw./Brkt. Assy.) (Ror. Matting)
99-10114 (Access Door) A037052-02 (Cabinet Assy) 036262.01 (Coin Box Brkt.) A002465-01 (Coin Counter)
Coin Acceptor~ ean ooh see Figure 23
03708501 ihaeebe dl Coin Box Lis)
78-3201 (tes) Schematics, Self-Test Label & Manuals— see parts list on next page
Figure 16 Cabinet-Mounted Assemblies A037051-xx B
Red 8aron/Sit-Down
Figure 16 Cabinet-Mounted Assemblies, continued Parts List
Part No, Description
A002465-01 Coin Counter A034631-01 Power OnlOff Switch Assembly A034841-08 US. Strain-Relief Power Cord A034863-08 German Strain-Relief Power Cord A035989-08 Australian Strain-Relief Power Cord
| A036189-01 | interlock Switch/Bracket Assembly | (modified for safety) |
A036247-01 Printed-Circuit-Board Interconnector
| A036320-01 | Volume/Self-Test’Coin Switch Assembly | (includes bracket) |
A036992-01 Main Harness Assembly
| A037052-02 | Wood Cabinet Assembly with Pallet | (includes swivel casters) |
The following seven items are the technical information supplements to this game: DP-171-01 Red Baron™/Sit-Down Schematic Drawings (Sheet 1)
| DP-171-02 | Red Baron/Sit-Down Schematic Drawings | (Sheet 2) |
| DP-171-.03 | Red Baron/Sit-Down Schematic Drawings | (Sheet 3) |
ST-171 Label with Self-Test Procedure and Option Switch Settings TM-151 Instruction and Service Manual for Electrohome G05-802/805 Quadrascan™ X-Y Monitor TM-164 Service Manual for Wells-Gardner 15- and 19-Inch X-Y Monitors TM-171 Red Baron/Sit-Down Operation, Maintenance and Service Manual
| 02-305007 | 7/8-Inch Black Piastic T-Molding | (at top of seat back) |
| 02-305010 | %-Inch Black Piastic T-Molding | (used throughout except on seat back) |
| 19-9032 | 50-Ohm, 12¥2-Watt, Wirewound Rheostat | (vo/ume control) |
48-009 8-Inch 8-Ohm 8-Watt Round High-Fidelity Speaker 61-162A DPST Power OniOff Toggle Switch 62-041 SPDT Momentary-Contact Pushbutton Utility Coin Switch with Black Cap 69-001 DPDT Slide Switch (for se/f-test)
| 71-2110 | Panel Cartridge Lock Mechanism | (for rear door) |
75-9910NO 518-11 Steel Stamped Nut (for utility coin switch)
| 78-24012 | 5-Inch Beaded Nylon Tie-Wrap | (for PCB edge connector) |
78-3201 Cabinet-Leveling Leg 92-047 or Electrohome 19-inch X-Y Monitor, or 92-050 Wells-Gardner 19-Inch X-Y Monitor 99-10114 Metal Front Access Door 002728-01 Control-Pane!l Mounting Bracket 005419-01 Speaker Grille 006450-01 On/Off Switch Mounting Plate 007882-02 Interlock Switch Cover 009992-01 On/Off Switch Cover 034536-03 Foam Vibration Damper (for aii three PCBs) 035462-01 Monitor Shield with Graphics
| 035465-01 | Cardboard Monitor Bezel with Graphics | (includes two guns) |
035745-02 18-Inch Plastic PCB Retainer 035745-03 10-Inch Plastic PCB Retainer 035851-01 Hinge for Rear Door 036262-01 Coin Box Bracket 036321-01 Bracket for Volume/Self-Test/Coin Switch Assembly 036686-01 Sheet of Game Pricing Labels 037074-01 Rear Door (inciudes PCB retainers, but no lock or hinges) 037083-01 Corrugated Rubber Floor Matting 03708401 Coin Box 037085-01 Coin Box Lid 037086-01 Retainer for Front Window 037087-01 Bronze-Colored Front Window 037090-01 Blue Monitor Overlay 037095-01 Cardboard Cowiing Bezel with Graphics 178023-001 4-lnch Diameter Swivei Caster
Red Baron ™/Sit-Down
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without tne specilic written permission of Atari, Inc., Sunnyvale, CA. This drawing is oniy conditionally’ Issued. and neither receipt nor possession theteo! conlers or ivansfers any right in, of license to use, the subject matter of the draw: ing or any design oF technical information shown thereon. nor any ‘right to reproduce this drawing or any part thereof, Except for manufaciure by vendors of Atari, Inc. and for manufacture under the corporation's written license, no tight to reproduce this drawing is granted or the subject matter thereoi unless by written agreement with of written permission from the corparatior.
Joystick Assy— See Figure 18
82-039 (Start Sw.) 77-9910WO (Nut) A036948-01 75-07054 (Harness) (Washer) 037077-01 (Spacer}
033127-01 (Sw. Bushing)
Figure 17 Control Panel Assembly A037057-01 A
Part No. Description
A036948-04 Control Panel Harness Assembly A037096-01 Control Panel with Graphics 62-039 SPDT Momentary-Contact Pushbutton Start Switch with Red Light-Emitting Diode 75-07054 Flat Nylon Washer, 0.470-Inch Inside Diameter x 0.968-Inch Outside Diameter x 0.075-Inch Thick
77-9910W0O #15132-32 Steel Stamped Nut 033127-01 Black Moided Switch Bushing 037077-01 Control Panel Spacer
Red Baron™/Sit-Down
036953-01 (Plate)
036961-01 (Shaft) 036279-03 \ A036958.01 (Pivot Ball) { (Shalt Assy ) 73-21232 (Pin)
036952-01 (Housing)
A036281-02. (Bellows)
036955-01 (Cap)
75-0108: (Washer)
\ oae9s6-02—| (Outer Gimbal)
036956-01 (Inner Gimbal) ~~ 75-9408 (Hex Nut) a 178027-001 (lubnicant— not shown)
72.8614 72-5240 i (Screw) (Screw) 036276-01 pha. Qe (Bezel)
62-043 (Switcny
036995-01, -02 (Ctrl Handle)
036963-01 (Slide Plate)
036954-01 (Mount. Plate)
72-8406 (Screw)
19-9026, (Resistor)
036957-01 (Linkage) 75-07020 (Washer)
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific written permission of Ata‘i, Inc.. Sunnyvale, CA. This drawing is only conditionally issued, and neither re. ceipt nor possession thereo! confers or translers any right in, or license to use. the subject matter of the drawing or any design or technical information shown thereon, or any right to reproduce this drawing or any part there: of. Except for manutacture by vendors of Atan, Inc., and for manufacture under the corporation's written license, no right to reproduce this drawing 1s granted or the sub: ject matter thereof unless by written agreemem with or written permission from the corporation
Figure 18 Gimbal-Type Joystick Assembly A036951-01 A
Figure 18 Gimbal-Type Joystick Parts List Assembly Red Baron™/Sit-Down
Ss
Part No. Description
A036281-02 Centering Beliows A036958-01 Shaft Assembly with Fire Switch Harness (includes pivot ball, pivot shaft and slotted pin) 03627601 Bezei for Fire Pushbutton 036279-03 Pivot Ball 036952-01 Pivot Ball Housing (two of these required per handle) 036953-01 Square Contro! Plate 036954-01 Mounting Plate 036955-01 Bellows Cap 036956-01 Inner Gimbal 036956-02 Outer Gimbal 036957-01 Gimbal Linkage 036961-01 Pivot Shaft 038963-01 Slide Plate 034995-01 Contro! Handle (right half 2.3.5 036995-02 Conirol Handle (left half) ¢ ¢ 19-9026 5K Ohm, + 20%, 2¥%W Variable Resistor 62-043 SPST Pushbutton Switch with Red Non-Lighting Cap (used as fire switch) 72-5240 #10-32 x 2¥2-Inch Hex-Head Steel Machine Screw 72-8406 #4-40 x 3/8-Inch Hex Cap-Head Steel Machine Screw 72-8614 #6-32 x 7/8-Inch Hex Socket-Head Steel Machine Screw 73-21232 3/16-Inch Diameter x 2-Inch Long Slotted Pin 75-0108 #10 Zinc-Plated Steel Flat Washer 75-07020 3/8-Inch Flat Washer 75-940S #10-32 Sieel Self-Locking Polymer Hex Nut 178027-001 Nyogel 779 Lubricant
Red Baron ™/Sit-Down
R33 5 wo Geet
| 6 | §>5 | 2 | | |
[| 0 O14
| -LI2Oe | -O | =) | 0 | |
| aw | - | Q | ||
| QS | LP | a | ||
| co | ¢c2zi | ? | 0 | of |
ay N
| — | 3300 | | — |
35V
rs C23 C3l
| L | Sov. | feet} | Lez} |
[iE 22) cee C24,
| Res | .— | (=) |
| 40,5WE pe | QS | Ips |
7812 7908
| fe) | 38 | 4R24,1.0,7WE- | oe) |
4%
| TIP32 | TOAZOOZA | TDAZ00ZA | |
| 02 | ala | aS | arr |
| R | Oc | eo | N |
| oeahes | cop | © creas | |
| q | SSIS | pg COED | CISG@D | |
| —l | sheel** | ae | |
| 0 | ERS | 220 [Rl \/2w |
s cle Ba pi aco _* © ods CSI Re9
| Chae | C4 | <Dcii() | |
| 420 | + | + | TEDRID |
“ a
| | | a | RO | £49 |
| | | 3 | Fo | +}— |
| - | 0 | pez0y | 35V |
R30e% RAW CIB}
| ) °— | 8 | Co | 0 |
| \ | s+ | 3300ur |
{] 35V NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproguction forbidden withgut the specific wittten permission of Atari, Inc., Sunnyvaie, CA This drawing is only conditionally ‘ssued, and neither re. ceipt ror possession thereot conlers of transfers any right in, oF license to use, the Subject matter of the draw jing or any design or technical informvation sncwn thereon, nor any right 0 reproduce this drawing of any part there: ‘of. Except for manutacture by vendors of Atari, Inc., and for manufacture unger the corporation's written eense, no right to reproduce this diawing +5 granted or the Sub: ject matter thereo! unless by written agreement wilh or waitten permission trom the corporation,
aS
Figure 19 Regulator/Audio Ii PCB Assembly A035435-02 c
Red Baron™/Sit-Down
Figure 19 Regulator/Audio !i PCB Assembly Parts List
Part No. Description (Reference Designations and Locations in Bold)
| 12-52P7 | 27 Ohm, + 5%, 1W Resistor | (R5) |
| 16-54PO | 4 Qhm, +5%, 5W Wirewound Resistor | (R25) |
19-100P1015 .1Ohm, + 3%, 7W Wirewound Resistor (R24)
| 19-315102 | 1K Ohm Vertical PCB-Mounting Cermet Trimpot | (R8) |
| 24-250108 | 1000 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor | (C13) |
| 24-250477 | 470 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor | (C1, 4, 12) |
| 24-350226 | 22 uf Aluminum Electrolytic Fixed Axial-Lead 35V Capacitor | (C24, 31) |
| 24-350338, | 3300 uf Aluminum Electrolytic Fixed Axial-Lead 35V Capacitor | (C9, 10, 18, 19) |
24-500105, 4 uf Aluminum Elecirolytic Fixed Axial-Lead 50V Capacitor (C22, 23)
| 29-088 | .1 uf Ceramic-Disc 25V Radial-Laad Capacitor | (C3, 11, 20, 21) |
31-1N4002 SOV 2.5A Miniature Axial-Lead High-Current Rectifier (CR1, 4-8)
| 33-TIP32 | PNP Power Transistor, Type TIP32 | (Q2) |
| 34-2N3055, | NPN Silicon Transistor, Type 2N3055 | (Q3) |
37-LM305 5V Linear Voltage Regulator (Q1)
| 37-7812 | +12V Voltage Regulator, Type 7812 | (Q8) |
| 37-7905 | — 5V Voltage Regulator, Type 7905 | (Q9) |
72-1608C #6-32 x Y2-Inch Cross-Recessed Pan-Head Corrosion-Resistant Steel Machine Screw 75-F60405 #6-32 x 4-Inch Binder-Head Nylon Screw 75-99516 #6-32 Nut/Washer Assembly
| 78-16008 | Thermally Conductive Compound | {Q3) |
| 78-16014 | Thermally Conductive Silicon Insulator | (Q2, 9) |
| 79-58306 | 6-Position Connector Receptacle | (J6, 9) |
| 79-58308 | 9-Position Connector Receptacle | (J7) |
| 79-58346, | 12-Position Connector Receptacle | (J10) |
79-58354 4-Position Connector Receptacle (J8) 020670-01 Test Point 03453101 Heat Sink 110000-010 1 Ohm, + 5%, %4W Resistor (R10, 19) 110000-100 10 Ohm, + 5%, t4W Resistor (R11, 20, 29, 30} 110000-101 100 Ohm, + 5%, YsW Resistor (R4, 12, 22)
| 410000-102 | 1K Ohm, + 5%, %W Resistor | (R27, 28) |
.110000-103 40K Ohm, + 5%, %W Resistor (R13, 14)
| 110000-271 | 270 Ohm, x 5%, Y%4W Resistor | (R1) |
110000-330 33 Ohm, + 5%, VaW Resistor (R3)
| 110000-392 | 39K Ohm, + 5%, %W Resistor | (R6) |
| 110000-562 | 5.6K Ohm, + 5%, MW Resistor | (R32, 33) |
110000-752 7.5K Ohm, + 5%, YW Resistor (R7)
| 110001-221 | 220 Ohm, + 5%, Y2W Resistor | (R9, 21) |
416000-220 22 Ohm, + 5%, 10W Wirewound Resistor (R31) 122002-102 .001 uf Ceramic-Disc Minimum 25V RadialLead Capacitor (C2, 7, 16)
| 122004-224 | .22 uf Ceramic-Disc 25V Capacitor | (C6, 8, 15, 17) |
| 100015-103 | .04 uf Cerarnic-Disc 25V Radial-Lead Capacitor | (C5, C14) |
| 137151002 | Type TDA2002A 8W Linear Audio Amplifier Integrated Circuit | (Q5, 7) |
Red Baron ™/Sit-Down NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reprodrction forbidden without the specific written permssion of Atari, Inc, Sunnyvale, CA This. drawing 1s only conditionally’ issued, and neitrer receipt nor possession tereo! confers ar translers any right in, or license to use, he subject matter of the draw: ing oF any design or technical information shown thereon, nor any right to reptoduce tis drawing or any gart thereo!, Except for manufacture by vendors of Aart. Ine. and for manulacture under the corporation's written license, no right to reproduce this drawing is granted or the subject matter theraof unless by written agreement with or written permission from ihe corporation,
| > | oD | oO | iv} | m | 7 | =x | oo | x | re |
-3ov =
| Bs | Be | = | isl | tg |
—_ m
| gp | ik) | | aes | ess |e) | (8) 013 ae | ||
| Oe | 7a | u | fee 256 | N | ba | ; |
we ass ' ae we
| a | t | P | ra | ry | |||||
| AR | [oR | u | o | ° | ip! | : | 1 | A | 4 |
I vwe yy, £63 =~ _,
| @] | t | i | é | ||
| | | ° | 8 | Q | 8 | 8 |
asa cara)
SOS a eS iced re]
Sear t “eS cs Racal 2S SS pees coral
| + | m= | SD | |||
| d | = | 7 | z | BO] 9» F2, | u |
gt es [EP an es es? pasty ort
| rt | of | 7. |
Figure 20 Red Baron™ Auxiliary PCB Assembly A036305-01 A
Red Baron™/Sit-Down
Figure 20 Red Baron™ Auxiliary PCB Assembly > Parts List
Part No. Description (Reference Designations and Locations in Bold)
C012284-01 Audio /O N-Channel MOS/LS! Custom Chip (B2)
| 12-5821 | 820 Ohm, +5%, 1 W Resistor | (R39) |
| 21-101103 | 01 uf, + 10%, Radial-Lead Epoxy-Dipped 100V Mylar Capacitor | (C8) |
| 21-101104 | -luf, +10%, Radial-Lead Epoxy-Dipped 100V Mylar Capacitor | (C21, 22, 32) |
| 21-101153 | .015 ui, + 10%, Radial-Lead Epoxy-Dipped 100V Mylar Capacitor | (C12) |
| 24-250106 | 10 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor | (C30, 50, 52) |
24-250107 100 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (C46) 24-250226 22 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (C5)
| 24-250476 | 47 uf Alurninum Electrolytic Fixed Axial-Lead 25V Capacitor | (C53) |
24-250477 470 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (C35, 43)
| 24-350106, | 10 uf Aluminum Electrolytic Fixed Axial-Lead 35V Capacitor | (C54) |
| 24-350476 | 47 uf Aluminum Electrolytic Fixed Axial-Lead 35V Capacitor | (C53) |
24-500105, 1 uf Aluminum Electrolytic Fixed Axiai-Lead 50V Capacitor (C36, 37, 51) 28-101101 100 pf Radial-Lead Epoxy-Dipped 100V Mica Capacitor (C27)
| 29-006 | 1 uf, | 410%, 35V Tantalum Capacitor | (C48) |
29-088. 1 uf Ceramic-Disc Radial-Lead 25V Capacitor {C1-4, 6, 7, 9-41, 14, 18-20, 23, 25, 26, 28, 29, 31, 33, 38, 39-42, 44, 45, 49, 55, 56)
31-1N100 400V Type-1N100 Switching Diode (CRE, 7) 31-1N914 75V Type-1N914 Switching Diode (CRI, 2, 4)
| 32-1N5235 | 6-8V 500mW Type-1N5235 Zener Diode | (CR5) |
34-2N3643 60V 300mW Type-2N3643 NPN Transistor (Q1, 2)
| 37-LM324 | Type-LM324 Integrated Circuit | (K4, K5) |
37-1408 Type-1408 Digital-to-Analog-Converter Integrated Circuit (B4) 37-4066 Type-4066 Analog Switch Integrated Circuit (J5)
| 37-555 | Type-555 Timer Integrated Circuit | (J, K2) | |
| 37-74LS00 | Type-74LS00 Integrated Circuit | (A4, J4) | |
| 37-74LS02 | Type-74LS02 Integrated Circuit | (D3, C5) | |
| 37-74LS04 | Type-74LS04 Integrated Circuit | (D5) | |
| 37-74LS08 | Type-74LS08 Integrated Circuit | (F3) | |
| 37-74L832 | Type-74LS32 Integrated Circuit | (C4) | |
| 37-74LS74 | Type-74LS74 Integrated Circuit | (D4) | |
| 37-74LS139 | Type-74LS139 integrated Circuit | (BS) | |
| 37-74LS161 | Type-74LS161 Integrated Circuit | (C1, D1) | |
| 37-74LS164 | Type-74LS164 Integrated Circuit | (E4, F4) | |
| 37-74LS174 | Type-74LS174 Integrated Circuit | (AO) | |
| 37-74LS175 | Type-74LS175 Integrated Circuit | (HO) | |
| 37-74LS191 | Type-74LS191 Integrated Circuit | (A3, B3) | |
| 37-74LS244 | Type-74LS244 Integrated Circuit | (EO) | |
| 37-74LS273 | Type-74LS273 Integrated Circuit | (E3) | . |
| 37-74LS374 | Type-74LS374 Integrated Circuit | (FO, B1) | |
| 37-74808 | Type-74S08 Integrated Circuit | (K3) | |
| 37-74109 | Type-74109 integrated Circuit | (C3) |
37-7815 + 15V Voltage Regulator (VR2) 37-7915 ~15V Voltage Regulator (VR1)
| 38-MV5053, | Type-MV5053 Red Light-Emitting Diode | (CR3) |
{Continued on next page]
Red Baron ™/Sit-Down
Figure 20 Red Baron™ Auxiliary PCB Assembly, continued Parts List
i Part No. Description (Reference Designations and Locations in Bold)
41-3003 100 uH, + 10%, Hot-Molded Plastic Fixed RF. Choke (L1-4)
| 79-42C16 | 16-Contact Medium-nsertion-Force Integrated Circuit Socket | (Ai, AS, E1, F1, H1, J1, K1, L1) |
| 79-42C22 | 22-Contact Medium-Insertion-Force Integrated Circuit Socket | (C0) |
| 79-42C40 | 40-Contact Medium-Insertion-Force Integrated Circuit Socket | (B2, C/D2, E2, F/H2, J2) |
81-4302 Nylon Snap-In Fastener 020670-01 Test Point
| 036174-01 | Programmable Read-Only Memory | (A1) |
| 036175-01 | Programmable Read-Only Memory | (E1) |
| 036176-01 | Programmable Read-Only Memory | (F1) |
036177-01 Programmable Read-Only Memory (H1)
| 036178-01 | Programmable Read-Only Memory | (J1) |
| 036179-01 | Programmable Read-Only Memory | (K1) |
036180-01 Programmable Read-Only Memory (L1)
| 036464-01 | Programmable Read-Only Memory | (A5) |
100015-103 01 uf Ceramic-Disc 25V Radial-Lead Capacitor (C34)
| 110000-102 | 1K Ohm, + 5%, %4W Resistor | (R1, 4, 12, 17, 19, 21-23, 33, 37, 43, 64-72) |
110000-103 10K Ohm, + 5%, %W Resistor (R7-9, 11, 31, 32, 46-63)
| 110000-104 | 100K Ohm, + 5%, %W Resistor | (R29) |
| 110000-151 | 150 Ohm, + 5%, %4W Resistor | (R35, 44) |
| 110000-152 | 1.5K Ohm, + 5%, %W Resistor | (R34) |
110000-153 15K Ohm, + 5%, %W Resistor (R27) 110000-221 220 Ohm, + 5%, YW Resistor (R20) 110000-222 2.2K Ohm, + 5%, %W Resistor (R16, 40) 110000-223 22K Ohm, + 5%, %W Resistor (R28, 36, 38) 110000-273 27K Ohm, +5%, YW Resistor (R30) 110000-333 33K Ohm, +5%, VaW Resistor (R6, 26) 110000-334 330K Ohm, +5%, Y4W Resistor (R25) 110000-391 390 Ohm, +5%, %4W Resistor (R45)
| 110000-392 | 3.9K Ohm, +5%, %W Resistor | (R15) |
110000-471 470 Ohm, +5%, “%4W Resistor (R13, 41, 42)
| 110000-473 | 47K Ohm, +5%, YW Resistor | (R2) |
| 110000-562 | 5.6K Ohm, +5%, %4W Resistor | (R85, 10, 18) |
| 110000-681 | 680 Ohm, +5%, %W Resistor | (R24) |
110000-683 68K Ohm, +5%, vaW Resistor (R3) 110000-822 8.2K Ohm, +5%, %W Resistor (R14) 122000-225 2.2 uf, + 20%, 35V Tantalum Capacitor (C47) 122004-224 .22 uf Ceramic-Disc 25V Radial-Lead Capacitor (C13, 15-17, 24)
| 137002-001 | Type-74S86 Integrated Circuit | (H4) |
| 137003:001 | Type-74S03 Integrated Circuit | (J3) |
437004-001 Transistor Array (C/02, 2, F/H2, J2) 137161-001 Read-Only Memory (CO) Note: /f you replace this part, you must erase this ROM before locking up the game. See Figure 6, Self-Test Procedure, in this manual for instructions. If you do not erase the ROM, the self-test will show the ROM to be “defective” by displaying the number 9 on the screen. 179010-001 12-Pin PCB Header (J16, J17)
*Program memory components — see parts list on next page.
NOTICE TOALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden with: ‘out the specific written permission of Atal, inc., Sunnyvale. CA. This drawing is only condi. tionaly issued, and neither receipt nor possession thereof confers or transters any right in, or license 10 use, the subject matter of tne draw ing or any design of technical information shown thereon, nor any right to reproduce this drawing or any part thereol. Except for man ufacwure by vendors of Atari, Inc, and tor Panulacture under the corporaiion’s written Cense, no right to reproduce this. drawing is granted o: the subject matter thereof unless by written agreement with or written permission from the corparation. OL
tb
Figure 21 v Red Baron ™/Sit-Down
ace] 1 Sec Lv Seon
a Saad S015 g
| Ae | =] | fl | me | & | ||
| FL fe) (F) ate | = | i] | lei] | & | ||
| 30 | ff] | mike | iP | ole | iE | vs |
cpcas
| Zw | e | fl | fl |
| 2 | e | b | ol & |
| a | Eg | OSs) |
a=}
¥
- See
Red Baron™ Analog Vector-Generator PCB Assembly
A036949-01 and -02 A
Red Baron™/Sit-Down
om Figure 21 Red Baron™ Analog Vector-Generator PCB Assembly Parts List
Memory-Component Equivalents (Locations Shown in Bold):
-01 P.C. Boards -02 P.C. Boards
037005-01 (A3) 037007-01 (A3) 037003-01 (E3)
037004-01 (BIC3) 037006-01 (BIC3) 037002-01 (F/H3)
Remainder of Memory Components:
Part No. Description (Locations in Bold)
036995-01 Read-Only Memory (P1) 036996-01 Read-Only Memory (N41) 036997-01 Read-Only Memory (UM1) 036998-01 Read-Only Memory (K1) 036999-01 Read-Only Memory (J1) 037000-01 Read-Only Memory (F/H1) 037001-01 Read-Only Memory (E1)
Red Baron™/sit-Down
Figure 21. Red Baron™ Analog Vector-Generator PCB Assembly, continued Parts List
A WARNING Although this PCB may closely resemble Baitlezone™ and other XY game PCBs, it is not interchangeable with them. Attempting to use this Red Baron™ PCB in any other game may cause a fire!
Part No. Description (Reference Designations and Locations in Bold)
A035742.01 and -02, Rev, ©
19-007 40K Ohm, + 20%, 1%4W 8-Pin Dual-Inline-Package Resistor Network (RP1, RP2—use only if board has 74LS170s or 74LS670s at locations £6, F6, H6) 19-315103 10K Ohm Vertical PCB-Mounting Cermet Trimpot (R88, 98) 19-315201 200 Onm Vertical PCB-Mounting Cermet Trimpot (R73, 74) 21-101102 .001 uf, + 10%, Radial-Lead Epoxy-Dipped 100V Mylar Capacitor (C69, 70, 93, 94)
21-101103 .01 uf, + 10%, Radial-Lead Epoxy-Dipped 100V Mylar Capacitor (For -02 PCB Assy. only: C103) 24-250106 10 ut Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (C17, 18) 24-250107 100 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (C78, 83-86) 24-500105 1 uf Atuminum Electrolytic Fixed Axial-Lead 50V Capacitor (C30, 89, 90) 27-102182 .0018 pf, + 10%, Radial-Lead Ceramic-Disc 1000V Capacitor (For -01 PCB Assy. only: C103; For -02 PCB Assy. only: C105)
| 28-191100 | 10 pf Radial-Lead Epoxy-Dipped 100V Mica Capacitor | (C44) |
| 28-101101 | 100 pf Radial-Lead Epoxy-Dipped 100V Mica Capacitor | (C27) |
| 28-101151 | 150 pf Radial-Lead Epoxy-Dipped 100V Mica Capacitor | (C63) |
| 28-101221 | 220 pi Radial-Lead Epoxy-Dipped 100V Mica Capacitor | (C82) |
| 28-101390 | 39 pf Radial-Lead Epoxy-Dipped 100V Mica Capacitor | (C25, 64, 106) |
28-101470 47 pf Radial-Lead Epoxy-Dipped 100V Mica Capacitor (C104) 29-006 tuf, + 10%, 35V Tantalum Capacitor (C88) 29-088 -1 uf Ceramic-Disc 25V Radial-Lead Capacitor (C1-16, 19-23, 26, 28, 29, 31-41, 45, 46, 50-54, 61, 72-77, 79-81, 97, 98. Also, for -01 PCB Assy. only: C40, 41, 48, 49. For -02 PCB Assy. only: C42, 43, 50, 51)
| 31-1N100 | 100V Type-1N100 Switching Diode | (CR11,12) |
| 31-1N914 | 75V Type-1N914 Switching Diode | (CR1, 3-10) |
| 33-2N3906, | Type-2N3906 PNP Switching and Amplifying Transistor | (Q3, 7) |
34-2N3904 Type-2N3904 NPN 60V 1-Watt Transistor (Q1, 2, 8, 9) 34-2N6044 Type-2N6044 Darlington NPN Transistor (Q4-6)
| 37-LM319. | Type-LM319 Integrated Circuit | (B12, 012) |
| 37-TLO82CP | Type-TL082 Integrated Circuit | (A10, D10) |
| 37-13201 | Type-LF 13201 Integrated Circuit | (B10, D11, E10) |
| 37-347 | Type-TL084 Integrated Circuit | (C11) |
| 37-74LS00 | Type-74LS00 Integrated Circuit | (J4) |
| 37-74LS02 | Type-74LS02 Integrated Circuit | (N9, M7) |
| 37-74LSC8 | Type-74LS08 Integrated Circuit | (5, P8) |
| 37-74LS10 | Type-74LS$10 Integrated Circuit | (Ka) |
| 37-74LS14 | Type-74LS14 Integrated Circuit | (B6) |
| 37-74LS20 | Type-74LS20 Integrated Circuit | (M5) |
| 37-74LS27 | Type-74LS27 Integrated Circuit | (N7) |
[Continued on next page]
Red Baron™/sit- Down
Figure 21. Red Baron™ Analog Vector-Generator PCB Assembly, continued Parts List
Part No. Description (Reference Designations and Locations in Bold)
A035742-01 and -02, Rev. C
37-74LS32 Type-74LS32 Integrated Circuit (J5, K10, M8) 37-74LS42 Type-74LS42 Integrated Circuit (B4, J7) 37-74LS74 Type-74LS74 Integrated Circuit (H10, L10, M9) 37-74LS86 Type-74LS86 Integrated Circuit (D7) 37-74LS109 Type-74LS 109 Integrated Circuit (N8) 37-74L.S139 Type-74LS139 Integrated Circuit (C4, K5, M2) 37-74LS157 Type-74LS157 Integrated Circuit (D4, E4, F4, H4) 37-74LS161 Type-74L$161 Integrated Circuit (K6, 14, L6, M6, N6)
37-74LS164 Type-74LS164 Integrated Circuit 37-74L8174 Type-74L$174 Integrated Circuit (C7, L7, M11) 37-74LS175 Type-74LS175 Integrated Circuit (F8, F9, J8, K8) 37-74LS191 Type-74LS191 Integrated Circuit (F10, J6)
37-74LS193 Type-74LS193 Integrated Circuit (E5, F5, H5) 37-74LS194 Type-74LS194 Integrated Circuit (A5, A6, B5, C5, D5, D6) 37-74LS244 Type-74LS244 Integrated Circuit (K3, N2, P2, N11, P11, R11) 37-74LS245, Type-74LS245 Integrated Circuit (F2, R4/5, R5) Acceptable substitute is part no. 37-8304B.
37-74LS273 Type-74LS273 Integrated Circuit (C8) 37-74.S367 Type-74LS367 Integrated Circuit (F7, H7) 37-74LS393 Type-74LS393 Integrated Circuit (M4, N5) 37-74LS399, Type-74LS399 Integrated Circuit (H8)
37-74LS670 Type-74LS670 Integrated Circuit (E6, F6, H6} Acceptable substitute is part no, 37-74LS170. 37-74S00 Type-74S00 Integrated Circuit (C6) 37-74S02 Type-74S02 Integrated Circuit (K9) 37-74S04 Type-74S04 Integrated Circuit (K2, R9)
37-74S74 Type-74S74 Integrated Circuit (J10, L9) 37-74S260 Type-74S 260 Integrated Circuit (L8) 37-7404 Type-7404 Integrated Circuit (H11) 37-74193 Type-74193 Integrated Circuit (N4)
37-7805 +5V Voltage Regulator (VR2) 37-7815 + 15V Voitage Regulator (VR3) 37-7915 ~15V Voltage Regulator (VR1) 38-MV5053, Type-MV5053 Light-Emitting Diode (CR2) 41-3004 100 UH, + 10%, Hot-Molded Plastic Fixed R.F. Choke (L1) Acceptable substitute is part no. 41-3003. 62-001 SPST Momentary Pushbuiton Switch (SW1) 66-114P1T 4-Station Single-Throw, Dual-Inline-Package Bit Switch (111) 66-118P1T 8-Station Single-Throw, Dual-Inline-Package Bit Switch (M10, P10)
79-42024 24-Contact Medium-Insertion-Force Integrated Circuit Socket (A3, B/C3, D3, E1, E3, F/H1, F/H3, J1, J3, K1, M1, N1, Pt) 79-42C40 40-Contact Medium-insertion-Force Integrated Circuit Socket (L/M/N3) 81-4302 Nylon Snap-In Fastener 90-102 42.096 MHz, + 005%, Crystal (¥2) 90-6013 Microprocessor (UM/N3) 90-7033 Random-Access Memory (A1, A2, B1, B2, C1, C2, D1, D2, H2, J2) 020670-01 Test Point 036408-01 Programmable Read-Only Memory (K7)
Red Baron ™/Sit-Down
Figure 21. Red Baron™ Analog Vector-Generator PCB Assembly, continued Parts List
Part No. Description (Reference Designations and Locations in Bold)
A035 742-01 and -02, Rev. C 100015-103 .01 uf Geramic-Disc Minimum 25V Radiai-Lead Capacitor (C47, 55, 57, 58, 60, 62, 65-68, 71, 91, 92, 95, 96, 99, 100) 110000-101 100 Ohm, +5%, %4W Resistor (R70, 75)
| 110000-102 | 1K Ohm, +5%, “%4W Resistor | (R18, 20, 27, 67, 84-86, 94, 110, 128-133) |
| 110000-103 | 10KOhm, +5%, “4W Resistor | (R9-17, 19, 21, 25, 26, 33, 44, 51-66, 95, 99, 125-127. |
tn addition, for -01 PCB Assy. only: R48, 50, 69)
| 110000-104 | 100K Ohm, +5%, V4W Resistor | (R35-42) |
110000-122 1.2K Ohm, +5%, VW Resistor (R46)
| 110000-151 | 150 Ohm, +5%, “4W Resistor | (R103) |
110000-153. 15K Ohm, +5%, “VV Resistor (R93)
| 110000-221 | 220 Ohm, +5%, %4W Resistor | (R24) |
110000-222 2.2K Ohm, +5%, YW Resistor (R45, 92, 102, 112, 114-116, 119-121, 123)
| 110000-223 | 22K Ohm, +5%, YW Resistor | (R28-32) |
110000-270 27 Ohm, +5%, YW Resistor (R111) 110000-332 3.3K Ohm, +5%, YaW Resistor (R87, 97) 110000-392 3.9K Ohm, +5%, YW Resistor (R47, 49)
| 410000-471 | 470 Onm, +5%, YW Resistor | (R34, 104-109) |
| 110000-472 | 4.7K Ohm, +5%, V4W Resistor | (R43) |
110000-474 470K Ohm, +5%, %W Resistor (R413, 117, 118, 122) 110000-561 560 Ohm, +5%, YW Resistor (R96)
| 110000-680 | 68 Ohm, +5%, %W Resistor | (R124) |
110000-681 680 Ohm, +5%, %W Resistor (For -02 PCB Assy. only: R83) 110000-821 820 Ohm, + 5%, %W Resistor (For -02 PCB Assy. only: R68, 69, 82) 110003-752 7.5K Ohm, + 1%, 1/8W Metal-Film Resistor (R71, 72, 76-81, 89) 121007-473 .047 uf, +10%, Radial-Lead Epoxy-Dipped 100V Polycarbonate Capacitor (C56, 58) 122000-225, 2.2 uf, + 10%, 35V Tantalum Capacitor (C87)
| 137002-001 | Type 74S86 Integrated Circuit | (B7) |
| 137149-001 | Type 74LS11 Integrated Circuit | (J9) |
137159-001 Type DAC-08 Digital-to-Analog Converter (C9) 137158-002 Type AM6012ADC Digital-to-Analog Converter (For -02 PCB Assy. only: A9, D9) OR OR 137160003 Type MC3410 Digital-to-Anaiog Converter (For 01 PCB Assy. only: 89, E9) 179014-012 12-Pin PCB Header (J19)
Red Baron /Sit-Down
an 034482.02 79-4411001 03454401 036304.01 48-2017002 46-2014001
79-3206
TOP VIEW
(F2 is not used)
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproauction forbidden without the 78-70501SC ‘Specific written permission of Atari, Inc. Sunnyvale. CA. This drawing 15 only conditionally issued, and nevther 29-053 receipt nor possession thereof conters or transfers any. agit in. of license to use, the subject matter of the deaw: ng or any design or technical intormation shown thereon, nor any ‘ight to reproduce this drawing or any part thereo}. Except for manutacture by vendors al Atari Inc, and tor manutacture under the corporation's written license. no right 10 reproduce this drawing 1s granted or the subject Matter thereo! unless by written agreement with of written permission from the Corporation
BOTTOM VIEW
3A-MDA3501
A035890-01 (Int'l.) A034630-01 or A036355-01 (U.S.) A034629-01 79-15021001
Figure 22 Power Supply Assemblies for X-Y Games A035892-01 (international) A / A036353-01 (U.S.) A
Red Baron™/Sit-Down
Figure 22 Power Supply Assemblies for X-Y Games Parts List
Part No. Description (Reference Designations in Bold)
A034629-01 A.C. Harness Assembly A034630-01 RFI Filter Assembly (FL1) A035674-01 Voltage Plug Assembly (set of four plugs—for international power supply only) A035888-01 or -02 Transtormer Assembly—international only (11) A035890-01 Power Harness Assembly (international only) A035891-01 Fuse Harness Assembly A036354-01 or -02 Transformer Assembly—U.S. only (11) A036355-01 Power Harness Assembiy (U.S. on/y} 29-053, 26,000 uf 15 VBC Electrolytic Capacitor (C1) 3A-MDA3501 Bridge Rectifier, Type MDA 3501 (CR1) 46-2014001 4-Amp. 125 V 3AG Slow-Blow Glass Cartridge-Type Fuse (F4, F5, F6) 46-2017002 7-Amp. 250 V 3AG Slow-Blow Glass Cartridge-Type Fuse (F1) 46-302202 20-Amp. 250 V 3AB Slow-Blow Ceramic Cartridge-Type Fuse (F3) 78-2708 Nylon Type 6/6 Hole Bushing with 5/8-Inch inside Diameter x 55/64-Inch Outside Diameter x Ya-Inch Thick 78-70501SC 2-Inch Diameter Gapacitor Mounting Bracket 79-15021001 2-Circuit Single-Row Terminal Block 79-3206 &Position 3AG Fuse Block with %-Inch Quick-Disconnect Terminals 79-4411001 Panel-Mounting Non-Indicating 3AG Cartridge-Type Fuse Post 024482-02 Power Supply Chassis 03454401 Fuse Block Cover 036304-01 Label for Fuse Values
43,
Red Baron" /Sit-Down
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING 99-15038 CONFIDENTIAL. Reproduction forbidden without the 99-15001 thru 99-5012 ere Specthc writien permssion o} Alani, Inc., Sunnyvale, CA ‘Ret Button) (Bezel tor Button) This drawing ‘5 only conditionally *Ssued, and neither y receipt nor possession ihereot confers ct transfers any fight in, oF license to use. the subject matter of the draw: ing oF any ¢esign or technica’ information shown thereon Aor any fight to reproduce this drawing or any part thereul- Except for manulacture by venors of Alan, Inc and lor manulacture under the corporation's written license, no right to reproduce this drawing 1s granted or the subject matier thereo! unless by written agreement with or waiien permission trom te corporatien.
99-15052 (Spring tor Button) 99-15051 (Lamp Holder)
99-15026 99-15056 (Coin Inlet) (Screw tor Bezel)
99-15025 ——»_.” | Oe * {Coin Inlet) 4 (Bezel for Cover) a“ % 99-15039 pantor |! lear 99-15041 s (Cover) 99-15055 99-15044 (Reing, Screw) &. AN (Lockout Coil, rae | 99-15053 > om (Lockt. Coil Spring) 99-15054 991 (Pivot for Lever) (Coin Ret. Box) oo . 99-15030 [e— (Lockout Flap) ORG
¢ ; 1 x in + 99-5028
JX (Con Ret. Box)
G
99-15056 (Screw for Bezel) 99-15037 (Sw. Adjuster)
99-15060 a oa Cae? aoe ‘A036597-01 (Harness—Not shown for clarity) 99-15029 (Bracket) oo-1sot2-—~ 8 (Switch)
Figure 22 Double Coin Acceptor/Mount Assembly A036693-xx A
Red Baron Sit-Cown
Figure 22 Double Coin Acceptor/Mount Assembly, continued Parts List
Part No. Description
A036597-01 Double Coin Acceptor Harness Assy. 99-15001 Coin Return Button with U.S. 25¢ Price Plate 99-15002 Coin Return Button with U.S. $1 Price Plate 99-15003 Coin Return Button with German 1 DM Price Plate 99-15004 Coin Return Button with German 2 DM Price Plate 99-15005 Ccin Return Button with German 5 DM Price Plate 99-15006 Coin Return Button with Belgian 5 Fr Price Plate 99-15007 Coin Return Button with French 1 Fr Price Plate 99-15008 Coin Return Bution with Japanese 100 Yen Price Plate 99-15009 Coin Return Button with British 10 Pence Price Plate 99-15010 Coin Return Button with Australian 20¢ Price Piate 99-15011 Coin Return Button with Italian 100 Lire Price Plate 99-15012 Coin Return Button with U.S. 50¢ (2 x 252) Price Plate 99-15025 Left Half of Coin Iniet 99-15026 Right Half of Coin Inlet 99-15027 Side Plate of Coin Return Box 99-15028, Base Plate of Coin Return Box 99-15029 ‘Switch Bracket 99-15030 Fiap for Lockout Coil (U.S. 25%) 99-15036 Coin Return Cover 99-15037 Switch Adjuster 99-15038 Bezel for Coin Return Button 99-15039 Bezel for Coin Return Cover 99-15040 Coin Return Lever 99-15041 Lockout Coil 99-15042 Coin Switch for U.S. 25¢ 99-15051 Lamp Holder 99-15052 Spring for Coin Return Button 99-15053 Spring for Lockout Coil 99-15054 Pivot for Coin Return Lever 99-15055 Retaining Screw 99-15056 Screw tor Both Bezels 99-15060 Switch Cover
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
Red Baron™/Sit-Down 1st printing
YOUR COMMENTS, PLEASE!
Your comments will assist Atari in improving the usefulness of our publications They are an important part of preparing for revisions of manuals and parts catalogs. No postage stamp is necessary if mailed in the U.S.A
\f you have any technical questions about certain Atari or Kee Games products, or are requesting additional publications, we will immediately forward your note to the appropriate person
Page Comments
Fill in if you wish a reply
| Name ____ | on | — | a | ws te | |
| Firm | | Be | _ | ee | + Distributor | |
| Aduress | . | yee | — | SS | Operator |
| City 2 | = State | a | IP | Other | |
| Aiea Code | . Phone | — | ce |
BUSINESS REPLY MAIL
FIRST CLASS PERMIT NO. 1004 SUNNYVALE. CA
POSTAGE WILL BE PAID BY ADDRESSEE
Attn.: Field Service/Coin-Op Division P. O. Box 427 es as a De Atari, Inc. Le]
a Sunnyvale, Calitornia 94086 a a Ce
Second fold
wOly a6pe siyy ade, aun siyy Buole nD
----—~-~-~-—--L_—~.,
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
Warranty
Seller warrants that its printed circuit boards and parts thereon are free from defects in material and workmanship under normal use and service for a period of ninety (90) days from date of shipment. Seller warrants that its television monitors (in games supplied with monitors) are free from defects in material and workmanship under normal use and service for a period of thirty
- days from date of shipment. None of the Seller's other products or parts thereof are warranted.
If the products described in this manual fail to conform to this warranty, Sellers’ sole liability shail be, at its option, to repair, replace, or credit Buyer's account for such products which are returned to Seller during said warranty period, provided: «
- Seller is promptly notified in writing upon discovery by Buyer that said products are defective;
- Such products are returned prepaid to Sellers’ plant; and
- Seller's examination of said products discloses to Seller's satisfaction that such alleged S defects existed and were not caused by accident, misuse, neglect, alteration, improper repair, installation or improper testing
In no event shall Seller be liable for loss of profits, loss of use, incidental or consequential damages.
Except for any express warranty set forth in a written contract between Seller and Buyer which contract supersedes the terms of this order, this warranty is expressed in lieu of all other warranties expressed or implied, including the implied warranties of merchantability and fitness for a particular purpose, and of all other obligations or liabilities on the Seller's part, and it neither assumes nor authorizes any other person to assume for the Seller any other liabilities in connection with the sale of products under this order.
< The use of any non-Atari parts may void your warranty, according to the terms of the warranty. The use of any non-Atari parts may also adversely affect the safety of your game and cause injury to yourself and others. Be very cautious in using non-Atari-supplied components with our ia games, in order to insure your safety.
Atari distributors are independent, being privately owned and operated. In their judgment they may sell parts or accessories other than Atari parts or accessories. Atari cannot be responsible for the quality, suitability or safety of any non-Atari part or any modification including labor which is performed by such distributor.
This document is and contains contidential trade secret information of Atari, Inc.
This document is loaned under confidential custody for the sole purpose of operation, @ maintenance or repair of Atari equipment and may not be used by or disclosed to any person for any other purpose whatever, and remains the property of Atari, Inc.
Neither it nor the information it contains may be reproduced, used, or disclosed to persons not having a need to know consistent with the purpose of the loan, without written consent of Atari, Inc.
AL
ATARI
ATARI INC 1265 BORREGAS AVENUE P.O. BOX 427 SUNNYVALE, CALIFORNIA 94086 408/745-2000 ¢ TELEX 35-7488