CATHODE RAY TOMES

Super Pac-Man Parts and Operating Manual (Dec 1982)

Super Pac-Man (Namco, 1982) · Parts & Operating Manual · 90 pages · 38 sections · original scan

Page 1

December, 1982 Game Nos. 316 & 317

Bally/Midway’s

Parts and

Operating Manual

NO. 317 COCKTAIL

NO. 316 UPRIGHT

MIDWAY MFG. CO.

10750 W. Grand Avenue Franklin Park, Htinois 60131 U.S.A.

Phone: (312) 451-1360 Cable Address: MIDCO Telex No.: 72-1596

Form No. 0316-00300-0000

Page 2

WARNING

THIS GAME MUST BE GROUNDED. FAILURE TO DO SO MAY RESULT IN DESTRUCTION TO ELECTRONIC COMPONENTS.

WARNING: This equipment generates. uses. and can radiate radio frequency energy and if not and usedin accordance with the instructions manual. may cause interference to radio communications. It has been tested and found to comply with the limits for a CLASS A computing device pursuant to SUBPART J of PART 15 of FCC RULES. which are designed to provide reasonable protection against such interference when operated in a commerical environment. Operation of this equipment in a residential area 1s likely to cause interference in which case the user at his own expense will be required to take whatever neasures may be required to correct the interference.

ELECTRICAL BULLETIN: FOR ALL APPARATUS COVERED BY THE CANADIAN STANDARDS ASSOCIATION (CSA) STANDARD C22.2 NO. 1, WHICH EMPLOYS A SUPPLY CORD TERMINATED WITH A POLARIZED 2-PRONG ATTACHMENT PLUG.

CAUTION: TO PREVENT ELECTRIC SHOCK DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET

Sa BLADES CAN BE FULLY INSERTED TO PREVENT BLADE

E .

ATTENTION: POUR PREVENIR CHOCS ELECTRIQUES NE PAS UTILISER CETTE FICHE POLARISEE AVEC UN PROLONGATEUR. UNE PRISE DE COURANT OU_UNE AUTRE SORTIE DE COURANT, SAUF SI LES LAMES PEUVENT ETRE INSEREES A FOND SANS EN LAISSER AUCUNE PARTIE A DECOUVERT.

C6%lly|MIDWAY

OUR TOLL FREE NUMBERS FOR SERVICE INFORMATION CONCERNING THIS GAME, OR ANY OTHER BALLY/MIDWAY™ GAME YOU NOW HAVE ON LOCATION.

CALL US FOR PROMPT, COURTEOUS ANSWERS TO YOUR PROBLEMS

ANSWERS TO YOUR PROBLEMS.

Continental U.S. 800-323-7182 Illinois Only 1-800-942-0497

® COPYRIGHT MCMLXXXIII BY BALLY/MIDWAY CO. ALL RIGHTS RESERVED. NO PART OF THIS PUBLICATION MAY BE REPRODUCED BY ANY MECHANICAL, PHOTOGRAPHIC, OR ELECTRONIC PROCESS, OR IN THE FORM OF A PHONOGRAPHIC RECORDING, NOR MAY IT BE TRANSMITTED, OR OTHERWISE COPIED FOR PUBLIC OR PRIVATE USE, WITHOUT PERMISSION FROM THE PUBLISHER. THIS MANUAL IS FOR SERVICE USE ONLY, AND NOT FOR GENERAL DISTRIBUTION. FOR PERMISSION REQUESTS, WRITE: MIDWAY MFG. CO., 10750 W. GRAND AVE., FRANKLIN PARK, IL 60131 Printed in U.S.A.

Page 3

TABLE OF CONTENTS

DESCRIPTION PAGE

if Introduction .... 6... cece cece eee ner en en Eee EE eee EE EEE EE 1-1

TF Location and Setup Inspection ... 2. Installation 2-3 Self-Test ..... 2-3 Game Volume Adjustment Control . 2-4 Option Switch Settings 12-4

Game Operation Self-Test Mode... Attract Mode..... Ready to Play Mode Play Mode......... Two Player Operation

Maintenance and Repair CICAMING «one nicer ee nenge sence nee we eee nee eens wenn see ere Es 4-1 Fuse Replacement . Opening the Control Panel . Removal of the Main Display ‘Glass & TV. Bezel TV. Monitor Replacement.......... -4 Printed Circuit Board Replacement. Opening the Attraction Panel ..

Illustrated Parts Breakdown No. 316 — Super Pac-Man — Upright — Front. No. 316 — Super Pac-Man — Upright — Front arts * No. 316 — Super Pac-Man — Upright — Rear Access....... No. 316 — Super Pac-Man — Upright — Rear Access — Parts List No. 316 — Super Pac-Man — Header Fluorescent Light Assy. ...... No. 316 — Super Pac-Man — Header Fluorescent Light Assy. — Parts List . No. 317 — Super Pac-Man — Cocktail — Front........... No. 317 — Super Pac-Man — Cocktail — Front — Parts List. No. 317 — Super Pac-Man — Cocktail — Interior Access. . No. 317 — Super Pac-Man — Cocktail — Interior Access — Parts List Super Pac-Man — Control Assembly — All Versions — Parts List... Super Pac-Man — Control Assembly — All Versions ............+ Super Pac-Man — Power Chassis Assy. — 70VA., 115V. — All Versions . Super Pac-Man — Power Chassis Assy. — 70VA., 115V. — All Versions Super Pac-Man — Front Door Assy, — U.S.A. — 25@..........0 000s Super Pac-Man — Front Door Assy. — U.S.A. — 25¢ — Parts List .. Parts List

Page 4

TABLE OF CONTENTS (cont'd)

DESCRIPTION PAGE

Vi.

Vil.

Vill. Technical Troubleshooting ........-... 0.00 cece cece eee ence tee teen tn eet eee e tenes 6-1 Introduction General Suggestions .. Harness Component Troubleshooting . Transformer and Line Voltage Problems . A Glossary of Microprocessor Terms .. Introduction to the Z80 CPU...... General Purpose Registers ... Arithmetic and Logic Unit (ALU) .. Instruction Register and CPU Control . Z80 CPU Pin Description

Coin Door Maintenance Metal Coin Acceptor Merchanisms Plastic Coin Acceptor Mechanisms. .

TV. Monitor Manual IMtroductiOn 2.0.06. c cece cece eect ene ere teen eet ene n neers Symptom Diagnosis ....... Guide to Schematic Symbols Troubleshooting....... Theory of Operation... Differences Between Monitors Controls You May Not Touch Parts Interchangeability ..... Wells Gardner Monitor Schematic — 1 Wells Gardner Monitor Replacement Parts List . Electrohome Monitor Schematic — 19”... Electrohome Monitor Replacement Parts List Electrohome Monitor Schematic — 13”.... Electrohome Monitor Replacement Parts List .

Schematics and Wiring Diagrams Wiring Diagram Video P.C.B. — Component Layout . Video P.C.B. — Schematic......... CPU P.C.B. — Component Layout . CPU P.C.B. — Schematic.......... 70VA Power Supply P.C.B. — Component Layout 70VA Power Supply P.C.B. — Schematic ...... 70VA Power Chassis — Upright — Schematic 70VA Power Chassis — Cocktail — Schematic . Credit Multiplier P.C.B. — Component Layout . Credit Multiplier P.C.B. — Schematic Pees CeovoDOOOOo Bese ODNODTSBWN= ares)

Page 5

FIGURE

TNT TEEPE TT PPV Vnypy PEEP et PRPRPRT HROMAAAAAOoONHAHAOMAKODASA NNNNN EDAD HARE DERERA TABLE OF FIGURES

Assigned Point Values Location of Serial No., Interlock Switch, On/Off Switch, & Major Sub-Assemblies . Interlock Switch Operation .......... 0... cc eee eee eee eae Game Voiume Adjustment Control & Option Switch Location. Option Switch Settings . Location of Fuses ...... Opening the Control Panel — Upright Removing the Contro! Panel — Cocktail Opening the Cocktail Game .. Removal of Main Display Glass Removing Top Glass — Cocktail Removing Monitor — Upright . Opening the Cocktail Game .. Removing Monitor — Cocktail Replacing P.C.B.s — Upright... Replacing P.C.B.s — Cocktail . Opening the Attraction Panel — Upright . Replacing Fluorescent Tube Starter — Upright Removing and Replacing the Coin Acceptor .. Cleaning the Metal Coin Acceptor ... Lubricating the Metal Coin Acceptor . Opening the Plastic Coin Acceptor... Changing the Plastic Coin Acceptor to Accept American or Canadian Quarters . m4

Pree OoOWMAGAKRD & RONKNAVNOOAGA WNNNNE Daa EERE ERE RDN S Q m

Page 6

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 7

Super Pac-Man

IMPORTANT NOTE

DO NOT plug in your new game yet. Before you do anything to your game, we recommend that you read SECTIONS | and II of this manual completely. It will not take more than a few minutes and it may be very helpful.

I. Introduction

SUPER PAC-MAN is a one or a two player game. There are two models: the “UPRIGHT” and “COCK- TAL TABLE”. When the two player mode is selected on the Upright model, the players take turns at the controls to guide their player through the game course. If you have purchased the Cocktail Table model of this game, the rules of play are the same. The only difference is that in the two player mode of the Cocktail Table game, the picture flips to face you when it's your turn. When playing this game, you are in complete control of SUPER PAC-MAN. He will go wherever you tell him to. And he just loves to eat all the different maze objects (APPLES, BANANAS, DOUGHNUTS, HAM- BURGERS, etc.). However, he doesn't like the four ghosts, BLINKY (red), PINKY (pink), INKY (tur quoise), and CLYDE (amber) because they feel the same way about him as he does about the maze objects. BLINKY, PINKY, INKY, and CLYDE are four VERY SMART ghosts. They move very fast and seem to have a sixth sense which always lets them know exactly where SUPER PAC-MAN is in the maze. They never give up in their pursuit of him. One of their favorite tricks is to divide and try to trap him between them. You really have to keep an eye on them. But SUPER PAC-MAN can turn the tables on these four ghosts for short periods of time during each maze. All he has to do is let them get fairly close in their pursuit of him and then eat one of the POWER DOTS that every maze has in it. When this happens, it causes the four ghosts to turn blue with fright no matter where they are in the maze. This is because they know that when he eats a POWER DOT it gives SUPER PAC-MAN the ability to eliminate them. However, he can ONLY eliminate them for as long as they are blue.

The ghosts will only stay blue for a few seconds after SUPER PAC-MAN eats a POWER DOT. But they do give a warning BEFORE they turn back to their original colors — they start to flash.

As your skill level increases, the four ghosts speed up their pursuit of SUPER PAC-MAN and they stay blue for shorter and shorter periods of time after he eats a POWER DOT until, in the VERY high number mazes, they do not turn blue at all.

Bonus players (this is switch selectable) can be awarded to you as you reach or pass certain preselected point values. The assigned point values for all items that can be eaten are as listed in Figure 1-1.

Page 8

Major Features

A major new feaiure of your SUPER PAC-MAN game is that there are two SUPER POWER DOTS in each maze that, when eaten, will cause your PAC-MAN to turn into a SUPER PAC-MAN. SUPER PAC-MAN can go anywhere within the maze and eat anything that can be eaten. Nothing can stop him.

OBJECT EATEN

APPLES .. BANANAS... DOUGHNUTS HAMBURGERS . 22222, KEYS ... POWER DOTS.. SUPER POWER D: 1ST GHOST .. 2ND GHOST 3RD GHOST 4TH GHOST..

Game Objective

The object of the game is to HAVE FUN and survive as long as possible while constantly improving your skills, eating as many maze objects as you can, and eliminating as many ghosts as possible. As you do this, each following maze will be harder and harder to complete.

POINT VALUE

-- 10 POINTS EACH 20 POINTS EACH 30 POINTS EACH -40 POINTS EACH VARIABLE 50 TO 160 POINTS EACH . 50 POINTS EACH -100 POINTS EACH -200 POINTS EACH -200 POINTS 400 POINTS 800 POINTS .1600 POINTS

Figure 1-1 Assigned Point Values

Page 9

II. Location and Setup

INSPECTION

  • Remove the game from its shipping crate.
  • Inspect the entire outside of it for any signs of damage. C Any scratches?, dents?, cracks? O Any broken controls? O Any broken glass or plastic? O Just look it over closely and make a note of any signs of damage.
  • Remove the shipping cleats from the bottom of the cabinet.
  • Install the four levelers, one at each corner of the cabinet. C Level the cabinet.
  • Open the cabinet and inspect the inside of the game for any signs of damage. See Figure 2-1. 0 Also check to make sure all plug-in connectors on the wire harness are firmly seated.
NOTE: ALL connectors or plugs are keyed so they will only go together when all pins are properly lined up. O Replug any connectors found unplugged. DO NOT FORCE PLUGS ONTO CONNECTORS. DO NOT FORCE PLUGS TOGETHER . If it won't go on easily, assuming the keys are lined up, it either does not belong there or is damaged. O Make sure all printed circuit boards (P.C.B.’s) are firmly seated in their connectors. These connectors are also keyed. The P.C.B.’s will only go into them one way without being damaged. O Note the location of the game's serial number. See Figure 2-1. O Check all major subassemblies to be sure they are mounted securely. These are called out in Figure 2-1. Power supply. Control panel(s). T.V, monitor. Other P.C.B.’s and/or P.C.B. rack, etc. Power Chassis.
  • Make a note of any problems that can’t be easily corrected.
  • Call your distributor and/or service man about your problem list.
Page 10

SERIAL NUMBER

VIDEO & C.P.U. PRINTED CIRCUIT BOARDS

POWER SUPPLY P.C.B.

UPRIGHT REAR

SERIAL NUMBER (MAY BE LOCATED ON ANY CORNER) =~ ) wee

CONTROL PANEL (PLAYER 1).

VIDEO & C.P.U. PRINTED CIRCUIT BOARDS

INTERLOCK SWITCH (INSIDE DOOR) ON/OFF SWITCH

TV. MONITOR CONTROL

INTERLOCK SWITCH

POWER SUPPLY CHASSIS

UPRIGHT FRONT

TY. MONITOR

CONTROL PANEL (PLAYER 2)

POWER SUPPLY P.C.B.

POWER SUPPLY CHASSIS

ON/OFF SWITCH UNDER TABLE COCKTAIL INTERIOR ON PLAYER 2 SIDE

Figure 2-1 Location of Serial No., Interlock Switch, On/Off Switch, & Major Sub-Assemblies

2-2

Page 11

INSTALLATION

  • Location requirements: O Power: Domestic 110 V @ 60 Hz Foreign 200 V to 240 V @ 50 Hz O Temperature: 32° to 100°F (0° to 38°C) O Humidity: Not over 95% relative O Space required: Upright 25” x 33” (63 x 84cm) Cocktail 32” x 22” (81 x 55cm) 0 Game height: Upright 68” (170cm) Cocktail 29” (73cm)
  • Voltage Selection: Your game is designed to work properly on the line voltage where you are located. Check your line voltage with a meter to determine what its value is. Then check the power input wires to the main power supply transformer on your game to be Sure they are connected to taps which correspond to your line voltage value. If the power input wires to the main power supply transformer are not connected to taps which correspond to your local line voltage, move them to the proper taps. . If the line voltage in your area falls outside the upper or lower limits of the range of inputs covered by the main power supply transformer, DO NOT PLUG YOUR GAME IN until you have talked with your distributor and/or service man and obtained a solution to this problem. Otherwise you could damage your game.
  • Interlock and power ON/OFF switches: See Figure 2-1. O To help prevent the possibility of getting an electric shock while working inside the game cabinet, interlock switches have been installed at each cabinet access door (this DOES NOT include the coin door in the Upright models). O When any access door is opened, the interlock switch installed there turns off all power to the game. O Check each interlock switch for proper operation. After checking the line voltage in your area and determining that the input wires to the main power supply transformer of your game are connected properly — or — after obtaining a solution to your over or under voltage problem from your distributor and/or your service man, piug the game into your A.C. wall outlet. The game ON/OFF switches for both models are located as shown in Figure 2-1. Turn the game on and allow it to warm up a few minutes. Slowly open each access door to the game (this does not include the coin door on the Upright models). As the door is opened approximately 1” (2.54cm) the power to the game should go off (the T.V. monitor, all the lights, and all sounds will stop). If this does not happen, check the interlock switch by this door to see if it has broken loose from its mounting or if it is stuck in the “ON” position. lf the switch is found to be bad, turn the game off, unplug it, and replace the interlock switch. When done, plug the game back into the wall outlet, close the access door, and turn the game back on. After the game has warmed up, repeat the above interlock switch test. When the interlock switch is working properly and turns the power to the game off, power may be restored to the game with the access door(s) open. Take hold of the interlock switch plunger and gently pull it out to its fully extended position. THIS IS TO BE USED ONLY FOR SERVICING THE GAME. See Figure 2-2.

Figure 2-2 Interlock Switch Operation

SELF-TEST Your new game will Self-Test itself to see if it has any bad parts. The information it receives while testing itself will be shown on the T.V. monitor. Some information can also be heard through the game's speaker system. See the GAME OPERATION section for a more detailed description of this function. When there is a bad result according to the Self-Test, call your distributor and/or service man to have the trouble fixed unless it is something you can do yourself (such as replace a bad RAM or ROM chip).

Page 12

GAME VOLUME ADJUSTMENT CONTROL See Figure 2-3. The game volume control pot is located on the game CPU board assembly. There is only one pot. For adjustment, it may be reached through the rear access door on the Upright models. On the Cocktail Table models, you will have to open the tabie top to reach it. To make the sounds louder, turn the pot in a clockwise direction (7 _). To make the sounds less /oud, turn the pot in a counterclockwise direction ( #7 ~ ).

OPTION SWITCH SETTINGS To change the option switch settings, you DO NOT have to take the Main Game CPU Board out of the

VOLUME ADJUSTMENT

a

LOUDER game. They can be easily reached through the rear access door on the Upright models. On the Cocktail Table model, you do have to open the table top to reach them. When changing any options, ALWAYS put the game into the Self-Test mode, make your changes, check the results on the monitor screen, take the game out of the Self-Test mode, and play the game to be sure the switches have worked properly and that no switches were accidentally moved that were not meant to be. (These switches are small and this can happen.) The option switch settings and what they will make. the game do are shown in Figure 2-4. See Figure 2-3 for option switch locations.

OPTION SWITCH SW-2 (LOC. 5B)

OPTION SWITCH SW-3 (LOC. 5&)

Figure 2-3 Game Volume Adjustment Control & Option Switch Location

Page 13

SUPER PAC-MAN

OPTION SWITCH SETTINGS

DIP SWITCH SW-2 AT LOCATION 5B

DIFFICULTY LEVEL SETTINGS — “R1” IS THE EASIEST AND “RB” IS THE MOST DIFFICULT

SW#1 SW#2 SW#3 SW#4 SWH5 SW#6 SWH7 SWHE RANK “RO”—STANDARD LEVEL OF DIFFICULTY OFF OFF OFF OFF

RANK “R1”—EASIEST LEVEL OF DIFFICULTY ON OFF OFF OFF

RANK “R2”OFFOFF OFF
RANK “R3”ONOFF OFF
RANK “R4”OFFON OFF
RANK “RS”ONON OFF
RANK “R6”"—GRADUATED LEVELS OF DIFFICULTYOFFON OFF
RANK “R7”ONON OFF
*RANK “R8”’—FACTORY SETTINGOFFOFF ON
RANK “RQ”ONOFF ON
RANK “RA”OFFOFF ON
RANK “RB"—HARDEST LEVEL OF DIFFICULTYONOFF ON
RANK “RC"—EASIEST AUTO DIFFICULTY SETTING | OFFONON
RANK “RD”ONONON
RANK “RE”OFFONON
RANK “RF”"—HARDEST AUTO DIFFICULTY SETTING]ONONON

SW#1 SW#2 SW#3 SW#4 SWHS SWH6 SWH7 SWHB *SOUND OFF NO SOUND ON

SCREEN

SW#1 SW#2 SWH3 SW#4 SWHS SWHE SWH7 SWHB *NORMAL OPERATION OFF FREEZE VIDEO ON

*|NDICATES FACTORY RECOMMENDED SETTINGS PART NUMBER MO51-00316-C012

Figure 2-4 Option Switch Settings

2-5

Page 14

SUPER PAC-MAN

OPTION SWITCH SETTINGS

DIP SWITCH SW-3 AT LOCATION 5E

COINS PER CREDIT — COIN SWITCH 1

SW#1 SW#2 SW#3 SWH4 SWHS SWH6 SWH7 SWHB

*1 COIN1 CREDITOFF OFF OFF
1 COIN2 CREDITSON OFF OFF
1 COIN3 CREDITSOFF ON OFF
1 COIN6 CREDITSON ON OFF
1 COIN7 CREDITSOFF OFF ON
2 COINS1 CREDITON OFF ON
2 COINS3 CREDITSOFF ON ON
3 COINS1 CREDITON ON ON

BONUS SUPER PAC-MEN AWARDED AT THE FOLLOWING POINT VALUES:

BEGAN WITH 1, BEGAN WITH 2 OR 3 SUPER PAC-MEN 5 SUPER PAC-MEN SW#1 SW#2 SW#3 SW#H4 SWH5 SW#H6 SWH7 SW#HB

*1st S P-M300001st S P-M30000
2nd S P-M1000002nd S P-M100000OFF OFF OFF
300001st S P-M30000
800002nd S P-M120000ON OFF OFF
1st S P-M300001st S P-M40000
2nd S P-M1200002nd S P-M120000OFF ON OFF
1st S P-M30000ist S P-M30000
AND EVERY80000AND EVERY100000CN ON OFF
1st S P-M30000tst S P-M40000
AND EVERY100000AND EVERY = 120000OFF OFF ON

1st S P-M 30000 ONLY

AND EVERY = 1200001st S P-MP100000ON OFF ON

ONLY ONLY

1S P-M AT300001S P-M AT40000OFF ON ON

NO BONUS SHIPS GIVEN WITH THIS SETTING ON ON ON

DETERMINES NUMBER OF SUPER PAC-MEN PLAYER BEGINS GAME WITH:

SW#1 SW#2 SW#3 SW#H4 SWH5 SWH6 SWH7 SWHB *3 SUPER PAC-MEN OFF OFF 1 SUPER PAC-MAN ON OFF 2 SUPER PAC-MEN OFF ON 5 SUPER PAC-MEN ON ON

*INDICATES FACTORY RECOMMENDED SETTINGS PART NUMBER MO51-00316-C012

Figure 2-4 Option Switch Settings (cont.)

2-6

Page 15

Ill. Game Operation

SUPER PAC-MAN is a one or a two player game with a color T.V. monitor. The game gives a display which has all the parts shown below.

PLAYER 1 SCORE

PAC-MAN

RESERVE PAC-MAN The game has five possible modes of operation: ATTRACT, READY-TO-PLAY, PLAY, HIGH SCORE/ INITIAL, and SELF-TEST.

PLAYER 2 SCORE

ENERGIZER DOT

GATE KEY

SUPER POWER DOT

RACK IDENTIFIER

Identification of “On Screen” Graphics During Play

SELF-TEST MODE

The Self-Test mode is a special mode for checking the game switches and computer functions. It is the easiest and best way to check for proper operation of the entire game.

NOTE: Putting the game into Self-Test will cause it to erase any CREDITS on the game from its memory.

You may begin a Self-Test at any time by sliding the Self-Test switch to the “ON” position after the power to the game is on. When this is done the game will react as follows:

  • First, you will see random moving multicolored patterns on the screen.
  • Immediately following this, a rightside up test display is shown on the monitor screen. This will remain until you set the Self-Test switch back to the “OFF” position. This test display is shown at right.

3-1 RAM OK ROM 0K

¥-0 OK

ist CREDIT CREDIT COIN coOIN PACMAN RANK BOUND 00. 26ND

Self-Test — Menue

Page 16
  • If abad ROM or RAM chip is found by the game's internal check system during the Self-Test, the game indicates this to you by showing the location code of the bad chip(s) on the SCREEN. The following table translates the chip location codes into the actual position on the game's P.C. Boards.

RAM TEST INDICATIONS AND THEIR MEANINGS

INDICATION

RAM OK RAM 1 RAM 2 RAM 3 RAM 4 RAM 5, RAM 6 RAM 7 MEANING CHIP LOCATION

NO RAM IS OUT OF ORDER RAM 1 on VIDEO PCB is no good RAM 2 on VIDEO PCB is no good RAM 3 on VIDEO PCB is no good RAM 4 on VIDEO PCB is no good RAM 5 on C P U PCB is no good RAM 6 on C P U PCB is no good RAM 7 on C P U PCB is no good 2E 2H 2K 2J 3K 3L 2D

ROM TEST INDICATIONS AND THEIR MEANINGS

INDICATION

ROM OK ROM 1 ROM 2 ROM 3 MEANING

NO ROM IS OUT OF ORDER ROM 1 on C PU PCB is no good ROM 2 on CP U PCB is no good ROM 3 on C P U PCB is no good CHIP LOCATION

1c

1K

V/O TEST INDICATIONS AND THEIR MEANINGS

INDICATION

VO OK Vvo1 1/02 NO BI BITC BITC IT P Pp U U

  • To check your game function switches and buttons (coin counter switches, TEST CREDIT button, 1 PLAYER and 2 PLAYER buttons): activate each one while the game is in the Self-Test mode. You should hear a game sound for each activation. If you do not hear it, the switch/button is either not working, miswired, or disconnected. Check it out thoroughly. . RANK is a difficulty fevel setting with “R1” being the easiest and “RB” being the most difficult level of play. “RC” through “RF” are AUTO difficulty level settings with “RC” being the easiest and “RF” the hardest setting. !n “AUTO” the game measures. the player's skill level and AUTOMATICALLY gets harder as his/her skill level improves. MEANING

IS OUT OF ORDER 1 is out of order 2 is out of order

3-2 CHIP LOCATION

ar 4c

  • When finished with the Self-Test mode, slide the Self-Test switch back to the “OFF” position. CA cross hatch pattern appears on the monitor screen for about 2 seconds. If you wish to keep this test pattern on the monitor screen for further use, slide Self-Test switch back to the “ON” position after the cross hatch appears and before it disappears. When finished with the cross hatch pattern, set the Self-Test switch to the “OFF” position. G Normal game functions will now return to the monitor screen.
Page 17

ATTRACT MODE

  • The Attract mode starts: O Just after power has been turned on to the game. (Self-Test switch is in the “OFF” position.) O After a Self-Test has been completed. (Performing a Self-Test sets the credits in the game’s memory to zero “0",)

© BALLY MIDHAY 1980, lone

CREDIT oO »

Attract Mode Display 1

| OO OD ek, aE

POWER

‘SUPER @

BALLY MIDWAY 1960, Long

Attract Mode Display 2 O After a play has been finished and there are no more credits left in the game's memory. C In the Attract mode, the game will give the following displays centered on the monitor screen:

POKER

super @

€ BALLY MIDWAY 1980, 1982

eREorT 0 =

Attract Mode Display 3

Attract Mode Display 4

Page 18

“| $0000

© BALLY MIDWAY L980, 1982

CREDIT © CREDIT oO

Attract Mode Display 5 Attract Mode Display 7

O No matter where the game is in the Attract mode sequence, it will immediately go to the following display as soon as a game has been paid for. It will hold this display on the monitor screen until the “1 PLAYER" or “2 PLAYER” start button is pushed.

3RD 20000

at 40000

STH 30000

CREDIT oO

Attract Mode Display 6

Page 19

PUBH START BUTTON

i PLAYER ONLY

AST BONUS <€ FOR 30600 PTS’ 2ND BONUS @ FOR 100000 PTs’

ALLY MIDWAY L980, 1982

CREDIT &

Ready to Play Mode Display 1

READY-TO-PLAY MODE

  • The Ready-To-Play mode starts when enough coins have been accepted for a 1 or a 2 player game.
  • The Ready-To-Play mode ends when either the “1 PLAYER” or the “2 PLAYER” push button is pressed.
  • In the Ready-To-Play mode, the game will give one of the above displays centered on the monitor screen.
  • If no START button is pressed, the game will hold this display on the screen indefinitely.

PLAY MODE

  • The Play mode begins when the “1 PLAYER” or the “2 PLAYER’ start button is pressed. “STAGE 1”"10 PTS" is displayed and then “PLAYER __ READY!” is displayed below the “GHOST HOUSE” on the screen.
  • The Play mode ends when your last SUPER PAC- MAN has been eliminated. When this happens, “PLAYER __ GAME OVER’ is written across the center of the monitor screen (below the “GHOST HOUSE").
  • The game consists of a single maze with side exits. The items that your SUPER PAC-MAN wants to eat are located in maze corridors with locked doors at every possible entrance to them. You must direct your PAC-MAN to eat the KEYS PUSH START BUTTON

@ PLAYERS

FOR 30000 PIS’

FOR 100000 PTS¢

BALLY MIDWAY

Ready to Play Mode Display 2

positioned around the maze in order to gain access*to these sealed corridors. The only other way he can get at the food he wants to eat is to eat the KEY that opens the door to one of the two SUPER POWER DOTS in each maze and then eat that SUPER POWER DOT.

When he does this, your PAC-MAN grows to SUPER size and can munch his way through all the locked doors in the maze. YOU can give YOUR Pac-Man SUPER SPEED while he is SUPER size by pressing the SUPER SPEED button on the control panel. He will now move through the maze at a much faster pace. However, you will find that he is harder to steer when he is traveling at this SUPER SPEED and you will also notice that he stays SUPER size fora much shorter period of time when traveling at SUPER SPEED. . At the beginning of each game, SUPER PAC-MAN. appears right below the center of the “GHOST HOUSE” while the four ghosts appear at the “GHOST HOUSE”. BLINKY appears outside the doors and PINKY, INKY, and CLYDE appear inside the “GHOST HOUSE”. . When play begins, BLINKY (who'd love to eliminate him) immediately begins looking for SUPER PAC-MAN (who immediately begins eating KEYS just as fast as he can). As time passes, PINKY, INKY, and CLYDE (who'd also love to eliminate him) leave the “GHOST HOUSE” one ata time and begin looking for SUPER PAC-MAN — who is still busily eating KEYS and maze food just as fast as YOU can steer him to them.

Page 20

But with all four ghosts chasing him, it is not as easy to eat the KEYS and maze food (without being eliminated by a ghost) as it was earlier in the game. And BLINKY, PINKY, INKY, and CLYDE are four VERY SMART ghosts. For instance, they will divide up two, three, or four ways to try to trap SUPER PAC-MAN between them, in a corner, or even in one of the tunnels. You've really got to watch them! It seems like they always have some sneaky new trick up their sheets. However, if they get too close, SUPER PAC-MAN can always eat one of the flashing POWER DOTS. When this happens, it causes all four ghosts to turn blue with fright no matter where they are in the maze. This is because they know that when he eats a POWER DOT it gives SUPER PAC-MAN the ability to eliminate them. But, he can ONLY eliminate them for as long as they are blue. And they will only stay blue for a short period of time. But the ghosts do give a warning BEFORE they turn back to their original colors — they start to flash. When SUPER PAC-MAN eliminates a blue ghost, its point value appears on the monitor screen at the place where the ghost was eliminated while at the same time being added to your score, and the ghost disappears — all except for its eyes. The eyes go back to the “GHOST HOUSE” where they get another body of their original color. This done, they leave the “GHOST HOUSE” again and take up their pursuit of SUPER PAC-MAN once more. When he eats the last item of any particular maze: all movement stops immediately, the maze flashes and disappears. Next, the game displays “STAGE —_—"*__ PTS" and the next maze appears. All the players are in the new maze when it appears. The words “PLAYER __ READY!” are also there — right below the “GHOST HOUSE”. After a second or two passes, the words “PLAYER __ READY!” disappear and play begins.

You MUST eat ail the food in any particular maze in order to advance to the next one. The maze identifier symbols appear at the bottom edge of the monitor screen. As your skill level increases, the four ghosts speed up their pursuit of your SUPER PAC-MAN and they stay blue for shorter and shorter periods of time after he eats a POWER COT until, in the high number mazes, they do not turn blue at ail. Bonus players (this is switch selectable) can be awarded to you as you reach or pass certain preselected point values. The assigned point values for all items that can be eaten are as listed in Figure 1-1. When one of the ghosts happen to eliminate one of your SUPER PAC-MEN, assuming you have at least one remaining in reserve, the maze disappears. Next, the game displays “STAGE __” “___

3-6 PTS” and the maze re-appears. All the players are in the new maze when it reappears. The words “PLAYER __ READY!” are also there — right below the “GHOST HOUSE”. After a second or two passes, the words “PLAYER __ READY!" disappear and play begins anew. When one of the ghosts eliminates your LAST SUPER PAC-MAN, the words “GAME OVER" are displayed below the “GHOST HOUSE”, yourscore is displayed under “1 UP”, and in addition, if your score was the highest on this game to date, it will also be displayed under “HIGH SCORE?” at the top center of the monitor screen and go into the HIGH SCORE/INITIAL MODE. If your score was NOT the highest but was still one of the best five scores to date, the game will then also go into the HIGH SCORE/INITIAL MODE. After this the game will then either go into the Ready-To-Play mode (if there are still credits left in its memory) or into the Attract mode (if there are no more credits left in its memory). "If your score was not high enough to cause the game to go into the HIGH SCORE/INITIAL MODE, it will then either go into the Ready-To- Play mode (if there are still credits left in its memory) or into the Attract mode (if there are no more credits left in its memory). Most of the above holds true in the “2 PLAYER” mode also. But there are a few minor differences.

4989

ENTER YOUR INITIALS. *

SCORE STAGE... NAHE 49890 & A

SCORE STAGE. NAME AF8I0 8 a 30000 o NN 30000 aA 20000 1M 30000 ee | 2ND SRD aqtH STH

High Score/Initial Mode

Page 21

TWO PLAYER OPERATION The Upright and Cocktail Table models both have two player operation. In the two player mode, the rules of play are the same as in the single player mode. There are some additional rules, however.

  • In the Upright model, the players must take turns at the controls.
  • In the Cocktail Table model, each player has his own set of individual controls. The picture will flip to face you when it is your turn. (When itis not your turn, your set of controls will have NO effect on the game.)
  • Your turn lasts until one of the ghosts eliminates your SUPER PAC-MAN. At this point, the game wili do one of several things depending on whether or not the eliminated SUPER PAC-MAN was your last or if you still have others remaining in reserve.

SUPER PAC-MAN ELIMINATED — OTHERS RE- MAINING IN RESERVE

The chase stops. 0 Next, the game displays “STAGE __” “__ PTS”, the screen display changes to the screen display of the other player, it displays “PLAYER __ READY!” under the “GHOST HOUSE” at the same time one of the other player's reserve SUPER PAC-MAN appears. D After a second or two passes, the words “PLAYER _— READY!” disappear and play begins for the other player.

SUPER PAC-MAN ELIMINATED — NO OTHERS REMAINING IN RESERVE O Game displays the words “PLAYER ONE” or “PLAYER TWO” “GAME OVER” below the “GHOST HOUSE”. O Your final score is displayed under “1 UP” or “2 UP”, depending upon which player you were. In addition, if your score was the highest on this game to date, it will also be displayed under “HIGH SCORE” at the top center of the monitor screen and go into the HIGH SCORE/INITIAL MODE. If your score was NOT the highest but was still one of the best five scores to date, the game will then also go into the HIGH SCORE/INITIAL MODE. After this the game will display “STAGE __” and “__ PTS”. The other player's maze appears along with the words “PLAYER _— READY!” under the GHOST HOUSE. After a few moments, the words “PLAYER __ READY!” disappear and play begins for the other player. , If your score was not high enough to cause the game to go into the HIGH SCORE/INITIAL MODE, it will then display “STAGE __” and “__ PTS”. The other player's maze appears along with

3-7 the words “PLAYER —— READY!” under the GHOST HOUSE. After a few moments, the words “PLAYER __ READY!” disappear and play begins for the other player. After the last player's LAST SUPER PAC-MAN has been eliminated, if his score was not high enough to cause the game to go into the HIGH SCORE/ INITIAL MODE, it will then either go into the Ready-To-Play mode (if there are still credits left in its memory) or into the Attract mode (if there are no more credits left in its memory).

Page 22

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 23

IV. Maintenance and Repair

Your NEW game needs certain types of maintenance to keep it in good working order. CLEAN, well MAINTAINED games attract players and EARN MORE PROFITS. The most important thing for you to remember is to run the Self-Test EVERY TIME you collect money from the coin box. JUST LOOKING at your game WILL NOT tell you if all its controls and inside parts are working correctly. The Self-Test will inform you whether or not your game is working the way it should. The second most important thing you should remember is to clean the outside of the game and coin acceptor mechanisms on a regular basis.

CLEANING The outside of the game cabinet plus the metal can be cleaned with any non-abrasive household cleaner. However, the front of the T.V. monitor tube and both sides of all other glass and piastic on or in the game MUST be cleaned with anti-static cleaner ONLY. For cleaning the coin acceptors: hot soapy water may be used on the plastic ones and any household cleanser may be used on the metal ones. If you wish, special coin machine cleaners that leave no residue may be purchased from your distributor. DO NOT dry-wipe any of the plastic panels. This is because any dust that was on them can scratch their surfaces. If this has happened, anyone looking through this type of damaged plastic would feel he was looking at the game through a fog. This fogging damage CANNOT be repaired or reversed. The ONLY solution is to replace the damaged piece of plastic. FUSE REPLACEMENT This game contains severa! fuses located as shown in Figure 4-1.

  • UPRIGHT MODEL: As viewed from the back, facing the cabinet, with the rear access door removed; the fuses are located on the Power Chassis Assembly.
  • COCKTAIL TABLE MODEL: As viewed from the coin door side of the cabinet, with the monitor tilted open to one side; the fuses are located on the Power Chassis Assembly. Replace fuses ONLY with the type and size listed in the Illustrated Parts Breakdown Section of this manual. See the T.V. Monitor Manual (available on request from your distributor or the monitor manufacturer) and/or the T.V. Troubleshooting Section of this manual for information on these fuses.

FUSES LOCATED ON POWER SUPPLY BOARD AND POWER CHASSIS.

Figure 4-1 Location of Fuses

Page 24

OPENING THE CONTROL PANEL. See Figure 4-2.

  • UPRIGHT MODEL: O The control panel is held in place by three latches, one on the left side, one on the right side, and one on the front center. They are spring loaded to provide constant positive pressure on their latch plates. They can be reached through the coin door AFTER turning power to the game off. To release the latches, lift up and toward the center of the control panel. Once they are released, unhook them from their latch plates. To remove the control panel: Raise it up and tilt it toward you until you can see the cable behind it. Cradling the control panel between yourself and the cabinet, disconnect it from its cabling and nylon retaining strap. The control panel is now free and can be removed. To reinstall the control panel, reverse this procedure. QO

. COCKTAIL TABLE MODEL: Each control panel is held in place by several screws, two on the inside of the cabinet and three

LATCHES

Figure 4-2 Opening the Control Panel — Upright along the outside bottom edge of the control panel. Turn power to the game off. Open the coin box door and release the two latches indicated in Figure 4-4

CAUTION: The right hand latch is very close to the HIGH VOLTAGE on the monitor.

Once they're released, unhook them from their latch plates. Grasp the table top at “A” and openit as indicated in Figure 4-4.

CAUTION: Due to the weight of the monitor, EXTREME CARE MUST be taken when opening the cabinet.

4-2 Remove the screws which secure the control panel in place. See Figure 4-3. O To remove the control panel(s): Disconnect it from its cabling. The control panel is now free and can be removed. O To reinstall the control panel, procedure. reverse this

LIFT CONTROL UP

J REMOVE

  • SCREWS EACH SIDE

~*~ REMOVE(3) SCREWS

Figure 4-3 Removing the Control Panel — Cocktail

Page 25

Figure 4-4 Opening the Cocktail Game

REMOVAL OF THE : O The bezel may now be removed. MAIN-DISPLAY-GLASS AND/OR U To reinstall the T.V. bezel and the table top glass, THE TV. BEZEL ASSEMBLY reverse this procedure.

  • UPRIGHT MODEL: See Figure 4-5.
NOTE: In order to do this, the contro! panel MUST be removed first. See the “Upright Model” procedure. OD Turn the power to the game off and remove the control panel. O This frees the main-display-glass so it can be lifted up. O By putting your finger in the hole in the middle of the main-display-glass support, you can lift it up and out. See Figure 4-5. 0 Loosen the screws which secure the T.V. bezelglass-clamps in place. Move the clamps to the side and the bezel glass may be removed. Remove the above mentioned screws and the bezel with four bezel-glass-clamps may be removed. O To reinstall the T.V. bezel assembly and the maindisplay-glass, reverse this procedure.
  • COCKTAIL TABLE MODEL: See Figure 4-6.
NOTE: This may be done with the table top in the DISPLAY open or the closed position. If you decide to open the GLASS table top, TURN THE POWER TO THE GAME OFF FIRST. O Remove the screws which secure the table top glass clamps in place. Figure 4-5 Removal of Main Display Glass & T.V. Bezel CG Remove the table top glass. — Upright

4-3

Page 26
  • UPRIGHT MODEL: See Figure 4-7. 0 Turn power off to the game. O Open the rear access door. O Completely disconnect the T.V. monitor from ail its cabling. DON’T FORGET THE CHASSIS GROUND WIRE. Before removing the T.V. monitor, the main-display-glass MUST be removed. See above “Upright Model” procedure. With the removal of only four bolts, the T.V. monitor will be loose. The monitor mounting channels slide on top of and against iwo metal guides mounted to the cabinet's right and left sides. The monitor is removed by sliding it out the back of the cabinet. See Figure 4-7. To reinstall the T.V. monitor, reverse this procedure. After replacing the T.V. monitor, be sure to run the game Self-Test.

Figure 4-6 Removing Top Glass — Cocktail

T.V. MONITOR REPLACEMENT

CAUTION: High voltages may exist in any television unit, even with the power disconnected. Use EXTREME CAUTION and do not touch electrical parts or the T.V. yoke area with your hands or with metal objects held.in your hands! In addition, BE SURE TO USE HEAVY GLOVES when handling the monitor. You could cut your | hands on the metal T.V. chassis without such protection. REMOVE (4) BOLTS
DANGER: The TV. monitor DOES NOT contain an isolation transformer on its chassis (it is mounted instead on the floor of the cabinet). When servicing the monitor on a test bench, YOU MUST ISOLATE THE MONITOR FROM AC VOLTAGE WITH AN ISOLATION TRANSFORMER. Figure 4-7 Removing Monitor — Upright

4-4

Page 27

CLAMPS

Figure 4-8 Opening the Cocktail Game

  • COCKTAIL TABLE MODEL: See Figure 4-9. O Turn power off to the game. O Open the coin box door and release the two latches indicated in Figure 4-8.
CAUTION: The right hand latch is very close to the HIGH VOLTAGE on the monitor. O Once the latches are released, unhook them from their latch plates. O Grasp the table top at “A” and open it as indicated in Figure 4-8.
CAUTION: Due to the weight of the monitor, EXTREME CARE MUST be taken when opening the cabinet.

O Remove the screws which hold the table top glass clamps in place. 0 Remove the table top glass. O Lift out the T.V. bezel assembly. O Completely disconnect the T.V. monitor from all its cabling. DON’T FORGET THE CHASSIS GROUND WIRE. O Remove the screws holding the T.V. monitor chassis to the “L” brackets by the door hinge(s). See Figure 4-9. O Close the Cocktail Table and re-latch it. O Remove the screws which secure the T.V. monitor mounting brackets to the edges of the slot cut in the table top. See Figure 4-9. O Pry up the end of each monitor mounting bracket with a screwdriver or similar tool until you can grasp them both. 0 Lift the T.V. monitor straight up and out of the table top being VERY CAREFUL not to bump the neck of the picture tube. O To reinstall the T.V. monitor, reverse this procedure. C Be sure to check the clearance of the “L” brackets BEFORE setting the monitor into the table top. O After replacing the T.V. monitor, be sure to run the game Self-Test.

REMOVE 6 SCREWS (3 EACH SIDE) LIFT MONITOR STRAIGHT UP

REMOVE 4 SCREWS (2 EACH SIDE)

Figure 4-9 Removing Monitor — Cocktail

Page 28

PRINTED CIRCUIT BOARD (P.C.B.) REPLACEMENT

  • UPRIGHT MODEL: See Figure 4-10. C Turn the power to the game off. © Unlock and open the rear access door.

O Disconnect the Main Game Logic Board from all its cabling. O Disconnect the Auxiliary Game Logic Board from the Main Game Logic Board. O Remove the P.C.B. clamps indicated in Figure 4-10 and slide the Main Game Logic Board out the back of the cabinet. © CAREFULLY pop the Auxiliary Game Logic Board off its four snap-in mounting posts and lift it out the back of the cabinet.

O To reinstall the above P.C.B.’s, procedure.

NOTE: Ail P.C.B. connectors are keyed and wili ONLY fit one way without forcing them. The plugs on the cable harness which connect it to the P.C.B.’s are also keyed and will ONLY go onto their connectors one way without forcing them.
  • COCKTAIL TABLE MODEL: See Figure 4-11. Turn the power off to the game. reverse this

REMOVE SUPPORT FROM SIDE OF CABINET AND LIFT REMOVE SUPPORT AND LIFT POWER SUPPLY BOARD UP TO REMOVE .B.S UP TO REMOVE O Open the cabinet: Open the coin box door and release the two latches indicated in Figure 4-8.

CAUTION: The fi hand latch is very close to the HIGH VOLTAGE on monitor.

Once they're released, unhook them from their latch plates. O Grasp the table top at “A” and open itas indicated in Figure 4-8.

CAUTION: Due to the weight of the monitor, EXTREME CARE MUST be taken when opening the cabinet.

GB To remove the Main and Auxiliary Game Logic Boards. See Figure 4-11. Disconnect the Auxiliary Game Logic Board from the Main Game Logic Board. Remove the P.C.B. clamps indicated in Figure 4-11 and slide the Main Game Logic Board out of the cabinet. CAREFULLY pop the Auxiliary Game Logic Board off its four snap-in mounting posts and lift it out of the cabinet. See Figure 4-11. To reinstall the above P.C.B’s, procedure. reverse this

REMOVE (2) SUPPORTS TO REMOVE POWER SUPPLY BOARD FROM CABINET REMOVE BRKT. FROM SIDE OF CABINET TO REMOVE P.C.B.S

Figure 4-10 Replacing P.C.B.s — Upright

4-6 Figure 4-11 Replacing P.C.B.s — Cocktail

Page 29

OPENING THE ATTRACTION PANEL

  • UPRIGHT MODEL: See Figure 4-12. O Turn the power to the game off. O Opening the attraction panel: Remove the screws which secure the top bracket in place. (They are on its top side.) See Figure 4-12. Remove the top bracket and slide up the attraction panel. This exposes the attraction panel fluorescent light tube and its mounting bracket assembly. To reinstall the attraction panel, reverse this procedure. O The fluorescent light tube may be replaced at this time. BE CAREFUL NOT TO DROP IT.
WARNING: If you drop a fluorescent tube and it breaks, IT WILL IMPLODE! Shattered glass can fly six (6) feet or more from the implosion. Use care when replacing any fluorescent tube.

D Replacing the fluorescent tube starter. See Figure 4-13, Be sure the power to the game has been turned off. Grasp the starter (it is on the back of the mounting bracket), give ita quarter turn, and remove it from its socket. To replace the fluorescent light tube starter, reverse this procedure. C Replacement of the fluorescent tube mounting bracket assembly. Be sure the power is off to the game. Disconnect it from its power cable. Remove the screws at its right and left hand sides which secure it and gently slide it out the front of the cabinet, being careful not to catch its power cable on anything. To reinstall the fluorescent tube mounting bracket assembly, reverse this procedure. REMOVE SCREWS AND LIFT ATTRACTION PANEL UP

Figure 4-12 Opening the Attraction Panel — Upright

O Replacing the speaker. Be sure the power is off to the game. Remove the attraction panel and disconnect the speaker from its cabling. Remove the nuts and bolts which secure the

speaker and speaker grill in place and set them and

the speaker grill aside. Once the bolts which secure the speaker in place are removed, the speaker may be removed through the opening where the attraction panel was. Reverse this procedure to reinstall the speaker.

  • THE COCKTAIL TABLE MODEL HAS NO BACK- LIT ATTRACTION PANEL.

1/4 TURN TO REPLACE FLUORESCENT TUBE STARTER

Figure 4-13 Replacing Fluorescent Tube Starter — Upright

4-7

Page 30

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 31
Scan of page 31

This page is a drawing, shown as the original scan.

Page 32

NO. 316 — SUPER PAC-MAN — UPRIGHT — FRONT

@

©) G

@)

@)

qi)

)

©)

5-2

Page 33

NO. 316 — SUPER PAC-MAN — UPRIGHT — FRONT — PARTS LIST

ORDER BY PART NUMBER ONLY

ITEM PART NO. DESCRIPTION

0316-00900-00XF HEADER DISPLAY PLEXI 0537-00903-0057 GLASS CHANNEL — 7-5/8" LG. (2 REQ’D.) 0574-00903-0100 HEADER RETAINER BRKT. (2 REQ’D.) 0017-00101-0138 #8 x 5/8 TORX TAMPER RESISTANT SCR. (6 REQ’D.) 0017-00009-0522 LONG ARM KEY T-20 (FOR ABOVE SCREW) A595-0001 1-0000 HEADER LIGHT ASSY. 0017-00009-0393 BLACK SPEAKER GRILL W/SLOTS 0017-00003-0259 6” x 9” SPEAKER — 8 OHM, 7W. 0017-00101-0127 #8-32 x 1-1/2 CARRIAGE BOLT (4 REQ'D.) 0017-00103-0061 #8-32 HEX NUT W/SEMS (4 REQ’D.) 0508-00900-0000 19" T.V. BEZEL 0508-00905-0000 PLEX! 0508-00901-0000 PLEXI-GLASS CLIPS (4 REQ'D.) 0017-00101-0017 #6 x 1/2 BLK. SLT. HEX HD. SCREW (4 REQ’D.) 0316-00901-00XF MAIN VIEWING GLASS 0508-00108-0000 GLASS STOP BRKT. 0017-00101-0027 #8 x 3/4 SLT. HEX HD. M.S. (3 REQ'’D.) A316-00012-0000 CONTROL SHELF PLATE WELD ASSY. 0316-00902-0000 CONTROL SHELF OVERLAY — DECORATIVE 0941-00103-0100 CONTROL SHELF MTG. BRKT. — RIGHT 0941-00103-0200 CONTROL SHELF MTG. BRKT. — LEFT 0555-00901-0000 PLASTIC LOCATING PIN (4 REQ'D.) 0017-00009-0534 BASSICK CLAMP (3 REQ’D.) 0017-00101-0141 #8 x 11/16 UNSLOT. HEX HD. SCR. (10 REQ'D.) 0316-00903-0000 CONTROL SHELF STRAP A982-00017-0000 CONTROL ASSEMBLY A316-00005-0000 CONTROL SHELF CABLE ASSY. 0017-00042-0256 PUSH BUTTON ASSY. — RED (2 REQ'D.) 0017-00042-0260 PUSH BUTTON ASSY. — WHITE (2 REQ’D.) 0017-00032-0093 PUSH BUTTON SWITCH W/HOLDER (4 REQ'D.) 0017-00103-0054 5/8-11 PAL NUT (4 REQ'D.) A090-00300-11BK U.S.A. 25¢ DOUBLE COIN DOOR ASSY. A982-00015-0000 COIN DOOR CABLE ASSY. 0090-00002-04BK LARGE COIN DOOR FRAME 0017-00101-0121 #6-32 x 5/16 PHIL. TRS. HD. SCR. (3 REQ'D.) (MOUNTS COIN DOOR TO FRAME) 0935-00906-0100 KICK PLATE — 23” LG. 0017-00102-0048 3/8-16 x 2" LEG LEVELERS (4 REQ’D.) 0017-00103-0026 3/8-16 LEG LEVELER HEX NUTS (4 REQ'’D.)

Page 34

NO. 316 — SUPER PAC-MAN — UPRIGHT — REAR ACCESS

Page 35

NO. 316 —- SUPER PAC-MAN — UPRIGHT — REAR ACCESS — PARTS LIST

PART NO. ORDER BY PART NUMBER ONLY

DESCRIPTION

A945-00038-0000 0894-00916-0000 0017-00101-0141 0017-00003-0339

0017-00003-0439

0508-00102-0000 0595-00104-0000 0017-00102-0066 0017-00104-0014 0555-00901 -0000 0866-00120-0000 0017-00101-0141 0508-00108-0000 0508-00900-0000 A088-00016-0000 A082-90427-A000 0624-00902-0100 0624-00902-0500 0017-00101-0141 0017-00104-0037 A082-91109-A000 0017-00042-0014 0017-00101-0751 A945-00036-0002 A317-00015-0000 A084-91435-D316 A084-91436-F316 A317-00014-0000 0017-00101-0141 0017-00009-0478 0317-00101-0000 0017-00101-0124 A945-00019-0000 A961-00007-0000 0961-00109-0000 0017-00042-0255 0894-00702-00XF 0017-00100-0037 ON-OFF SWITCH & PLATE ASSY. RECESSED HAND PULL & VENT (2 REQ'D.) #8 x 11/16 UNSLOT. HEX HD. M.S. (8 REQ'D.) ELECTROHOME — 19” COLOR DUAL SYNC. HORIZ. MTG. MONITOR (OR) WELLS-GARDNER — 19” COLOR DUAL SYNC. HORIZ. MTG. MONITOR MONITOR MTG. CHANNEL (2 REQ’D.) MONITOR RAIL (2 REQ’D.) 1/4-20 x 3/4 UNSLOT. HEX HD. BOLT (4 REQ'D.) 7/8" DISH WASHER (4 REQ'D.) PLASTIC LOCATING PIN (4 REQ’D.) CHASSIS BRACE #8 x 11/16 UNSLOT. HEX HD. M.S. (4 REQ'D.) GLASS STOP BRACKET 19” T.V. BEZEL INTERLOCK SWITCH & SPRING BRKT. ASSY. POWER SUPPLY P.C. BOARD ASSY. P.C. SUPPORT BRKT. — 12” LG. (3 REQ’D.) P.C. SUPPORT BRKT. — 6-1/2" LG. (2 REQ'D.) #8 x 11/16 UNSLOT. HEX HD. M.S. (15 REQ'D.) #8 WASHER (15 REQ'D.) CREDIT MULT. BYPASS P.C.B. ASSY. 1/8" SNAP BUSHING (4 REQ'D.) #5-40 x 1/4 PHIL. RND. HD. M.S. (4 REQ’D.) POWER CHASSIS ASSY. — 70VA, 115V. CARD RACK HOLDER W/BOARDS ASSY. VIDEO BOARD P.C. ASSY. CPU BOARD P.C. ASSY. CARD RACK HOLDER & STOP ASSY. #8 x 11/16 UNSLOT. HEX HD. M.S. (4 REQ’D.) NYLON GUIDE (6 REQ’D.) CARD RACK BRACE BRKT. #6 x 1/4 UNSLOT. HEX HD. M.S. (2 REQ’D.) LINE CORD ASSY. — 115V. CASTER ASSY. (2 REQ'D.) WHEEL BRKT. (2 REQ’D.) PLASTIC WHEEL (2 REQ’D.) SHAFT (2 REQ'D.) 3/8" E-RING (2 REQ'D.)

Page 36

NO. 316 — SUPER PAC-MAN — UPRIGHT — REAR ACCESS — PARTS LIST (Continued)

ORDER BY PART NUMBER ONLY

ADDITIONAL PARTS LIST A950-00004-0000 COIN BOX ASSY. A950-00006-0000 COIN BOX CRADLE ASSY. 0950-00105-0000 COIN BOX COVER 0950-00104-0000 COIN BOX HANDLE 0950-00101-0000 COIN DEFLECTOR (2 REQ’D.) 0950-00900-0000 LARGE PLASTIC CASH BOX 0017-00101-0142 1/4-20 x 1-3/8 BLACK RND. HD. BOLT (4 REQ’D.) 0017-00104-0014 7/8" DISH WASHER (4 REQ’D.) 0017-00103-0018 1/4-20 HEX NUT (4 REQ’D.) A151-00098-0000 BACK DOOR LOCK ASSY. 0017-00009-0490 5-5/8" SQR. VENT GRILL (4 REQ’D.) — BACK DOOR 0950-00103-0000 COIN BOX DIVIDER — OPTIONAL A333-00012-0000 CREDIT SWITCH & BRKT. ASSY. A316-00011-0000 MASTER CABLE/BRKT/DIODE ASSY. A316-00010-0000 LOW VOLTAGE CABLE ASSY. A316-00009-0000 HIGH VOLTAGE CABLE ASSY. A316-00016-0000 VIDEO SIGNAL CABLE ASSY. A316-00017-0000 AUDIO ADAPTOR CABLE ASSY.

5-6

Page 37

NO. 316 — SUPER PAC-MAN — UPRIGHT — HEADER FLUORESCENT LIGHT ASSY.

NO. 316 — SUPER PAC-MAN — UPRIGHT — HEADER FLUORESCENT LIGHT ASSY. — PARTS LIST

ORDER BY PART NUMBER ONLY

PART NO. DESCRIPTION

0595-00105-0000 FLUORESCENT BRKT. 0017-00003-0043 18” COOL WHITE FLUORESCENT LAMP. 0017-00003-0445 LAMP LOCKS (2 REQ'D.) 0017-00031-0036 FLUORESCENT SOCKET (2 REQ'D.) 0017-00003-0412 FLUORESCENT STARTER HOLDER W/LEADS 0017-00101-0573 #6-32 x 1/2 PHIL. RND. HD. M.S. (4 REQ'D.) 0017-C0104-0009 #6 EXT. WASHER (4 REQ'D.) 0017-00003-0019 FLUORESCENT STARTER 0017-00003-0026 BALLAST 0017-00101-0598 #8-32 x 5/16 SLT. HEX HD. SCR. (4 REQ'D.) A961-00042-0000 LINE FILTER ASSY.

Page 38

NO. 317 — SUPER PAC-MAN — COCKTAIL — FRONT

5-8

Page 39

NO. 317 — SUPER PAC-MAN — COCKTAIL — FRONT — PARTS LIST

ORDER BY PART NUMBER ONLY | rem | PART NO. DESCRIPTION 0017-00009-0499 COVER GLASS — 32" x 22” x 1/4” 0317-00900-0000 DECORATIVE ARTWORK UNDERLAY 0775-00104-O00XF GLASS CLIPS (8 REQ'D.) 0017-00101-0117 #8 x 5/8 BLK. PHIL. TRS. HD. SCR. (8 REQ’D.) 0557-00900-0000 TV. BEZEL 0508-00106-0000 BEZEL MTG. BRKT. 0333-00905-0000 DIFFUSER 0508-00901-0000 PLEXI-GLASS CLIPS (4 REQ’D.) A317-00009-0100 CONTROL SHELF ASSY. — PLAYER #1 A317-00009-0200 CONTROL SHELF ASSY. — PLAYER #2 0017-00009-0393 BLACK SPEAKER GRILL W/SLOTS (2 REQ’D.) 0017-00009-0482 SPEAKER GRILL (NOT SEEN) 0017-00003-0187 6" x 9" SPEAKER — 8 OHM, 9W. 0017-00101-0137 #8-32 x 1" CARRIAGE BOLT (8 REQ’D.) 0017-00101-0127 #8-32 x 1-1/2 CARRIAGE BOLT (4 REQ’D.) 0017-00103-0061 #8-32 HEX NUT W/SEMS (12 REQ'D.) A090-00300-11BK U.S.A. 25¢ DOUBLE COIN DOOR ASSY. A982-00015-0000 COIN DOOR CABLE ASSY. 0090-60002-04BK LARGE COIN DOOR FRAME 0017-00101-0121 #6-32 x 5/16 PHIL. TRS. HD. SCR. (3 REQ’D.) (MOUNTS COIN DOOR TO FRAME) A927-00019-0000 COIN BOX ASSEMBLY A962-00004-0000 COIN BOX COVER ASSY. A962-00005-0000 COIN BOX SIDE CHANNEL ASSY. — SHORT 0962-00101-0000 COIN BOX SIDE CHANNEL — SHORT 0017-00101-0628 #8-32 x 3/4 CARRIAGE BOLT (4 REQ'D.) 0017-00104-0022 #8 FLAT WASHER (4 REQ’D.) 0017-00103-0061 #8-32 HEX NUT W/SEMS (4 REQ'D.) 0017-00102-0048 3/8-16 x 2" LEG LEVELERS (4 REQ'’D.) 0017-00103-0026 3/8-16 LEG LEVELER HEX NUTS (4 REQ’D.)

5-9

Page 40

INTERIOR ACCESS

  • COCKTAIL — MAN SUPER PAC. NO. 317 —

5-10

Page 41

NO, 317 — SUPER PAC-MAN — COCKTAIL — INTERIOR ACCESS — PARTS LIST

ORDER BY PART NUMBER ONLY

PART NO.

0017-00003-0339

0017-00003-0439

A515-00019-0000 A515-00019-0100 0017-00101-0109 0610-00132-00ZN 0017-00009-0534 0017-00101-0141 0927-00101-O0XF 0017-00101-0598 0017-00009-0514 0017-00101-0136 0017-00103-0061 0317-00901-0100 0317-00901-0200 A302-00015-0000 0510-00101-O0XF 0017-00101-0341 A334-00015-0000 A317-00010-0100 A317-00010-0200 0017-00032-0106 0017-00042-0304 0017-00032-0093 0017-00103-0054 0930-00104-0000 0017-00101-0025 0930-00904-0000 0017-00031-0044 0017-00003-0219 0017-00101-0555 A082-90427-A000 0624-00962-0100 0624-00902-0500 0017-00101-0141 0017-00104-0037 A082-91109-A000 0017-00042-0014 0017-00101-0751 A945-00036-0000 0942-00102-0000 A317-00015-0000 A084-91435-D316 A084-91436-F316 A317-00014-0000 0017-00101-0141 0017-00009-0478 0317-00101-0000 0017-00101-0124 DESCRIPTION

ELECTROHOME — 19” COLOR DUAL SYNC. HORIZ. MTG. MONITOR (OR) WELLS-GARDNER — 19” COLOR DUAL SYNC. HORIZ, MTG. MONITOR MONITOR SUPPORT ASSY. — LEFT MONITOR SUPPORT ASSY. — RIGHT #8 x 5/16 UNSLOT. HEX HD. BOLT (6 REQ’D.) STRIKE (2 REQ’D.) BASSICK CLAMP (2 REQ’D.) #8 x 11/16 UNSLOT. HEX HD. M.S. (8 REQ’D.) SUPPORT ANGLE (2 REQ’D.) #8-32 x 5/16 SLT. HEX HD. SCREW (4 REQ'D.) 2-1/2" HINGE (2 REQ’D.) #8-32 x 1-1/4 CARRIAGE BOLT (8 REQ’D.) #8-32 HEX NUT W/SEMS (8 REQ’D.) DECORATIVE OVERLAY PLAYER #1 DECORATIVE OVERLAY PLAYER #2 CONTROL PANEL WELDMENT ASSY. (2 REQ’D.) BOTTOM PAN (2 REQ'D.) #6 x 1/4 PHIL. TRS. HD. SCR, (6 REQ'D.) CONTROL ASSY. (2 REQ’D.) CONTROL SHELF CABLE ASSY. — PLAYER #1 CONTROL SHELF CABLE ASSY. — PLAYER #2 SMALL BUTTON SWITCH ASSY. W/HARDWARE (2 REQ’D.) PUSH BUTTON ASSY. — RED (2 REQ’D.) PUSH BUTTON SWITCH W/HOLDER (2 REQ’D.) 5/8-11 PAL NUT (2 REQ'D.) CONTROL PANEL LOCATING BRKT. (4 REQ’D.) #8 x 1/2 SLT. HEX HD. M.S. (16 REQ’D.) LIGHT SHIELD (2 REQ’D.) WEDGE BASE LAMP SOCKET (4 REQ’’D.) #194 WEDGE LAMP — 14V., .27A. (4 REQ'D.) #6-32 x 5/16 SLT. HEX HD. M.S. (4 REQ’D.) POWER SUPPLY P.C. BOARD ASSY. P.C. SUPPORT BRKT. — 12” LG. P.C. SUPPORT BRKT. — 6-1/2” LG. (2 REQ’D.). #8 x 11/16 UNSLOT. HEX HD. M.S. (7 REQ’D.) #8 FLAT WASHER (7 REQ’D.) CREDIT MULT. BYPASS P.C. BRD. ASSY. 1/8" SNAP BUSHING (4 REQ’D.) #5-40 x 1/4 PHIL. RND. HD. M.S. (4 REQ’D.) POWER CHASSIS ASSY. — 70VA., 115V. POWER CHASSIS MTG. BRKT. (2 REQ’D.) CARD RACK HOLDER W/BOARDS ASSY. VIDEO BOARD P.G. ASSY. CPU BOARD P.C. ASSY. CARD RACK HOLDER & STOP ASSY. #8 x 11/16 UNSLOT. HEX HD. M.S. (4 REQ’D.) NYLON GUIDE (6 REQ'D.) CARD RACK BRACE BRKT. #6 x 1/4 UNSLOT. HEX HD. M.S. (2 REQ’D.)

Page 42

NO. 317 — SUPER PAC-MAN — COCKTAIL — INTERIOR ACCESS — PARTS LIST (Continued)

ORDER BY PART NUMBER ONLY

ITEM PART NO. DESCRIPTION

A?75-00013-0000 FAN ASSY. 0151-00081-0000 4" FAN 0775-00110-00XF FAN PLATE 0749-00106-00XF VENT SCREEN 0017-00101-0347 #6-32 x 1/2” R.H.M.S. (4 REQ'D.) 0017-00104-0009 #6 EXT. WASHER (4 REQ’D.) 0017-00103-0005 #6-32 HEX NUT (4 REQ'D.) 0017-00101-0026 #8 x 5/8 SLT. HEX HD. SCREW (4 REQ’D.) A775-00018-0000 FAN CABLE ASSY. 0017-00003-0187 6" x 9” SPEAKER — 8 OHM, 9W.

ADDITIONAL PARTS LIST A088-00014-0000 INTERLOCK SWITCH & BRKT. ASSY. A945-00038-0000 ON-OFF SWITCH & PLATE ASSY. A317-00008-0000 MASTER CABLE W/BRKT. ASSY. A317-00006-0000 HIGH VOLTAGE CABLE ASSY. A317-00010-0000 LOW VOLTAGE CABLE ASSY. 0942-00902-0000 MONITOR SHIELD A927-00005-0000 HIGH BASE LEG KIT ASSY. — OPTIONAL A316-00016-0000 VIDEO SIGNAL CABLE ASSV. A088-00017-0000 TEST & CREDIT SWITCH & BRKT. ASSY.

SUPER PAC-MAN — CONTROL ASSEMBLY — ALL VERSIONS — PARTS LIST

ORDER BY PART NUMBER ONLY

PART NO. DESCRIPTION

1A932-00022-0000BALL & SHAFT ASSEMBLY
20017-00100-00251/4 E-RING
30921-00702-0000STOP SPACER
40921-00902-0000SLIDE PLATE
5A982-00013-0000PIVOT PLATE WELD ASSY.
69017-00101-0637#8-32 x 1” CARRIAGE BOLT (4 REQ’D.)
70017-00103-0061#8-32 HEX NUT W/SEMS (4 REQ'D.)
80932-00902-0000GROMMET
90017-00101-0598#8-32 x 5/16 SLT. HEX HD. M.S. (10 REQ’D.)
100962-00904-0000SLEEVE
10017-00101-0527#5-40 x 5/8 SLT. RND. HD. SCR. (8 REQ’D.)
120020-00202-0000SWITCH PLATE (4 REQ’D.)
13A932-00009-0000SWITCH ASSEMBLY (4 REQ’D.)
14A932-00012-00XFSTOP PLATE & SWITCH BRKT. ASSY.
150932-00905-0000WEAR PLATE
160921-00700-0000ACTUATOR
Page 43

5-13 SUPER PAC-MAN — CONTROL ASSEMBLY — ALL VERSIONS

Page 44

SUPER PAC-MAN — POWER CHASSIS ASSY. — 70VA, 115V. — ALL VERSIONS

5-14

Page 45

SUPER PAC-MAN — POWER CHASSIS ASSY. — 70VA, 115V. — ALL VERSIONS — PARTS LIST

ORDER BY PART NUMBER ONLY

PART NO. DESCRIPTION

0945-00108-00XF A945-00029-0000 0945-00107-01XF 0017-00101-0123 MT00-00101-A000

0017-00103-0061 MT00-00105-A000

MT00-00105-B000

0017-00103-0061 0945-00902-0000 0017-00101-0067 0945-00103-O00XF A945-00030-0400 0017-00021-0297 A945-00030-0300 A945-00030-0500 A945-00030-0200 A945-00021-0000 0017-00101-0573 0017-00103-0084 A945-00025-0000 0017-00021-0510 0017-00101-0140 0017-00101-0660 0017-00104-0107 0017-00103-0081 0017-00003-0263 0017-00003-0005 0017-00003-0444

0945-00904-0000 0945-00908-0000 0017-00003-0217 0017-00003-0007 0017-00003-0263 0945-00903-0000 0017-00101-0067 0017-00101-0780 0017-00021-0629 A945-00019-0000 CHASSIS MTG. PLATE & BARRIER ASSY. STRAP (2 REQ’D.) #8 x 1/4 UNSLOT. HEX HD. SCR. (12 REQ’D.) ISOLATION TRANSFORMER W/O SHIELD ASSY. — 115V., 50/60 HZ. #8-32 HEX NUT W/SEMS (4 REQ’D.) POWER TRANSFORMER W/O SHIELD — 70VA, 115V. (UPRIGHT ONLY) POWER TRANSFORMER W/SHIELD — 7OVA, 115V. (COCKTAIL ONLY) #8-32 HEX NUT W/SEMS (4 REQ'D.) SNAP BUSHING (3 REQ’D.) #6 x 3/8 PHIL. PAN HD. SCR. (11 REQ’D.) PARTITION — LOCATED UNDER CHASSIS (NOT SEEN) CONNECTOR & CABLE ASSY. 2 POSITION CONNECTOR CONNECTOR & CABLE ASSY. CONNECTOR & CABLE ASSY. CONNECTOR & CABLE ASSY. CONVENIENCE OUTLET ASSY. #6-32 x 1/2 PHIL. RND. HD. SCR. (2 REQ'D.) #6-32 HEX NUT W/SEMS (2 REQ'D.) FILTER ASSY. — 125V. — UNDER CHASSIS (NOT SEEN) TERMINAL STRIP #4-40 x 5/16 PHIL. PAN HD. SCR. (2 REQ'D.) #10-32 x 3/4 SLT. PAN HD. SCREW (NOT SEEN) #10 FLAT WASHER #10-32 HEX NUT W/SEMS SLO-BLO FUSE — 4A., 250V. FUSE — 2A., 250V. FUSE HOLDER — QUICK CONN. (2 REQ’D.) — FOR ABOVE FUSES 5 POSITION FUSE HOLDER FUSE BLOCK INSULATOR SLO-BLO FUSE — 2.5A., 250V. (2 REQ’D.) SLO-BLO FUSE — 3A, 250V. (2 REQ’D.) SLO-BLO FUSE — 4A, 250V. FUSE HOLDER BARRIER #6 x 3/8 PHIL. PAN HD. SCREW (2 REQ'D.) #6 x 1/2 PHIL. PAN HD. SCREW (2 REQ'D.) 5 POSITION TERMINAL STRIP (UNDER CHASSIS) LINE CORD ASSY. — 115V. (NOT SHOWN)

5-15

Page 46

FRONT DOOR ASSEMBLY — U.S.A. 25¢

/ h/ / 9a “@/

Page 47

FRONT DOOR ASSEMBLY — U.S.A. 25¢ — PARTS LIST

PART NO. ORDER BY PART NUMBER ONLY

DESCRIPTION

0090-00002-04BK 0017-00101-0121 A090-00073-02BK 0017-00101-0123 0017-00007-0019 0017-00103-0059 0090-0091 2-0000 A097-00005-0000 A097-00006-0000 0090-00128-00XF 0017-00005-0041 A090-00095-0000 0090-00126-03XF 0017-00101-0525 A090-00096-0000 0090-00903-9500 0090-00143-00XF 0017-00003-0219 0017-00031-0048 A090-00100-0000 0017-00103-0084 A090-00089-0000 0017-00101-0124 0090-0091 1-0000 A090-001 12-0000 0010-00134-0000 0010-00181-0000 0017-00007-0083 0090-00129-00XF 0090-00167-00XF 0090-00182-00XF 0017-00100-0018 A090-00088-0000 A090-00105-0000 0017-00005-0003 0017-00005-0211 0017-00005-0214 A090-00064-0000 0017-00101-0099 0090-00162-00XF 0017-00005-0203 0017-00005-0195 0010-00599-0000 0017-00007-0015 A090-00059-0400 0017-00101-0147 A090-00077-0000 DOUBLE ENTRY COIN DOOR FRAME #6-32 x 5/16 PHIL. TRS. HD. SCR. (3 REQ'D.) DOUBLE ENTRY COIN DOOR W/DRESS PLATE #8 x 1/4 UNSLOT. HEX HD. SCREW (12 REQ’D.) KEY HOOK PUSH NUT (4 REQ’D.) COIN ENTRY PLATE — 25¢ (2 REQ'D.) DOOR LOCK & KEY W/SCREW & NUT (OR) DOOR LOCK & KEY W/SCREW & NUT DOOR TILT SWITCH BRKT. DOOR CAM DOOR TILT SWITCH SWITCH BACK-UP PLATE #5-40 x 9/16" PHIL. HD. MSS. (2 REQ’D.) DOOR TILT SWITCH & BRKT. ASSY. (ITEMS 9 & 11 THRU 13) 25¢ WINDOW (2 REQ’D.) COIN PLEX RETAINER 12 VOLT LAMP — G.E. #194 (2 REQ’D.) WEDGE SOCKET W/BRKT. (2 REQ'D.) BRKT. ASSY. #6-32 HEX NUT W/SEMS (4 REQ’D.) COIN METER W/DIODE #6 x 1/4 UNSLOT. HEX HD. SCR. (4 REQ’D.) INSULATOR (2 REQ’D.) COIN CHUTE & INSULATOR ASSY. (2 REQ'D.) SPRING SPRING . 4/8 x 1-5/8 ROLL PIN PIVOT POST PIVOT LEVER REJECT LEVER E-RING REJECT LEVER ASSY. (2 REQ'D.) (ITEMS 30 THRU 33) COIN ACCEPTOR FRAME ASSY. (2 REQ’D.) COIN ACCEPTOR W/STRING CUTTER (2 REQ’D.) (OR) COIN ACCEPTOR W/ANTI STRING DEVICE (2 REQ’D.) (OR) COIN ACCEPTOR W/STRING CUTTER (2 REQ'D.) ANTI-PENNY DEVICE #6 x 1/4 SLT. HEX HD. M.S. (2 REQ’D.) COIN SWITCH MTG. BRKT. COIN SWITCH CHUTE COIN SWITCH COIN SWITCH WIRE PUSH-ON RING COIN SWITCH & WIRE ASSY. (ITEMS 40 THRU 42) #4-40 x 3/4 PHIL. PAN. HD. MS. (2 REQ’D.) COIN GUIDE & SWITCH ASSY. (ITEMS 38 THRU 43)

Page 48

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 49

VI Technical Troubleshooting

Introduction

The most common problems occur in harness components such as the coin acceptor, player controls, interconnecting wiring, etc. The TV monitor and PCB computer cause their share of problems too, but not as much as the harness and its component parts. TV monitor troubleshooting will not be covered here because it is covered in that section of this manual. As you already know, the PCB computer is a complex device with a number of different circuits. Some circuits remain basically the same among games, but overall there are a great many differences between them. PCB troubleshooting procedures, therefore, can be lengthy and will differ greatly among games. However, some basic Z-80 CPU information is involved in this section.

General Suggestions correctly identifying the We bg symptoms

The first step in any troubleshooting procedure is correctly identifying the We bg symptoms. This includes not only the citcuits or features malfunctioning, but also those still operational. A carefully trained eye will pick up other clues as well. For instance, a game in which the computer functions fail completely just after money was collected may have a quarter shorting the PCB traces. Often, an experienced troubleshooter will be able to spot the cause of the problem even before opening the cabinet. After all the clues are carefully considered, the possible malfunctioning areas can be narrowed down to one or two good suspects. Those areas can be examined by a process of elimination until the cause of the malfunction is discovered.

Harness Component Troubleshooting

Typical problems falling in this category are coin and credit problems, power problems and failure of individual features. NO GAME CREDIT For example, your prospective player inserts his quarter and is not awarded a game. The first item to check is if the quarter is returned. If the quarter is returned, the malfunction most certainly lies in the coin acceptor itself. First, use a set of test coins (both old and new) to ascertain that the player's coin is not undersize or underweight. If your test coins are also returned, coin acceptor servicing is indicated. Generally, the cause of this particular problem is a maladjusted magnet gate. Normally, this will mean slightly closing the magnet gate alittle by turning the adjusting screw out a bit (see section on coin acceptor for more details). If the quarter is not returned and there is no game credit, the cause of the malfunction may be in one of several areas. First try operating the coin return button; if the coin is returned, the problem is most likely in the magnet gate: Enlarge the gap according to the coin acceptor service procedures. If this does not cure the problem, remove the coin acceptor, clean it and perform the major adjustment procedure. If the trapped coin is not returned when the wiper lever is actuated, you may have an acceptor jammed by a slug, gummed up with beer, a jammed coin chute, or mechanical failure of the acceptor mechanism. In this case, first check for the slug that will generally be trapped against the magnet. If so, simply remove the slug and test the acceptor. lf the chute is blocked, remove the acceptor and remove the jammed coins. If there is actual failure of the acceptor, remove the unit and repair as indicated in the coin acceptor service procedures. If the coin is making its way through the acceptor (that is, falling into the coin box), yet there is still no game credit, you either have a mechanical failure of the coin switch or electrical failure of the coin and credit circuits. The first piace to begin is by checking the coin switch. Most of these switches are the make/break variety of micro switch, which is checked by testing for continuity between the NO, NC, and C terminals. When notactuated, the NC and C terminals should be continuous and the NO terminal open. When operated, the NO and C terminals should close and the NC should be open. If the coin switch checks out, examinethe connections to the terminals to make sure there is good contact. If necessary, use the continuity tester and check from the terminal lug on the switch to the associated PCB trace. This will tell you if there is a continuous lineall the way to the credit circuit.

Page 50

If the coin switch wires do not check out, the problem is in the computer — most likely in the coin and Credit circuitry. If you do get game credit when a coin is deposited, but the game will not start when the, start switch is pressed, you may have a problem in the start switch, the interconnecting wiring or in the computer. First check the switch. If the switch is OK, proceed to check the wiring. Again, make sure you go from the terminal lug on the switch to the PCB trace. This way, you will check the terminal contact as well as PCB edge connector contact. If the wiring is continuous, proceed to check the PCB credit circuit. If not, check. each section of the wiring, until the discontinuity is located. If the wiring is OK, the problem must lie in the computer.

Transformer and Line Voltage Problems

Your machine must have the correct line voltage to operate properly. If the line voltage drops too low, a circuit in the computer will disable game credit. The point at which the computer will fail to work will vary

some from game to game, but no game’ will work on

line voltage that drops below 105 VAC. Low line voltage may have many causes. Line voltage normally fluctuates a certain amount during the day as the total usage varies. Peak usage times occur mainly at dawn or dusk, so if your machine's malfunction seems to be related to the time of day, this may be a factor. A large load connected to the same line as the game (such as a large air conditioner or other device with an exceptionally large motor) may drop the line voltage significantly when starting up. This drop can result in an intermittent credit problem. In addition, poor connections in the location wiring, plug, or line cord may also cause a significant drop in power. Cold solder joints in the game's harness, especially in areas like the transformer connections, interlock switch, or fuse block, may also produce the same results, although probably on a more permanent basis. Sometimes location owners (especially in bars) replace light switches with dimmer rheostats, and the game is sometimes on the same line. Obviously, the voltage available to the game is going to drop dramatically when the dimmer is turned. In any case, the way to check for correct line voltage is with your VOM. Set the VOM to 250 VAC and stick the probes in the wall receptacle. If it's OK here, check the transformer primary connections. If you do not get 117 VAC, examine the solder joints on the transformer, fuse block, and interlock switch. If you do get 117 VAC, the problem must be either in the transformer, harness connections, or in the PCB power supply.

6-2 If you suspect the transformer, check its secondaries with the VOM set to 50 VAC and correlate the readings with the legend on the side of the transformer. The transformer must also be correctly grounded, so check the ground potential as well, especially if there is a hum bar rolling up or down the TV screen.

HARNESS PROBLEMS Other harness problems include blowing fuses and malfunctioning controls. The repeating blown-fuse problem can sometimes be quite exasperating to solve, for short circuits have the tendency to occur in areas almost impossible to find. First, try inserting a new fuse, as old fuses age and blow withouicause. If the new one also blows, you definitely have a short. The best way to approach this problem is by turning the power off and disconnecting devices that maybe causing the problem, such as the TV, transformer, and PCB. Disconnect the devices by pulling off their connectors, but do not allow them to touch. If necessary, insulate them with smail pieces of electrical tape. Then, connect your VOM across the terminals of the fuse block (all electrical power shut off), and set it to one of the resistance scales. This will save blowing a fuse each time you want tocheck the circuit. If the VOM reveals that disconnecting the devices removed the short, reconnect the devices one by one until the short returns. The last device connected is the one that is at fault. If the VOM reads a short even after the devices are disconnected, the fault must lie in the harness itself, and only patient exploration will reveal its location. First, carefully examine all the wiring, looking for terminals that may be touching, metal objects such as coins shorting connections or burned insulation. If necessary, use the VOM to check each suspected wire. MALFUNCTIONING CONTROLS One of the most common problems here is a bad potentiometer. Typically, a bad pot will cause the image to jump as it reaches a certain point. The only cure for this one is to install a new pot. If a feature that is operated by a switch (for example, joysticks, foot pedals, control panel buttons) does not operate at all, check the switch with a VOM or continuity tester to verify its operation. !f the switch does not check out, replace it. If the switch is OK, you should suspect the input to the switch from the PCB. In this case, get out the harness and logic schematics and check to see what kind of input it is. In many cases, the input will be +5 VDC. If so, use the VOM to check its presence. Normally, the switch is used to pull a +5 VDC line LOW to GND or to pulla LOW line HIGH. !f the PCB output is missing, check the wire length from the PCB. If you find the signal at the PCB trace, the wire length or connection is at fault. If not, begin expioring the PCB using the logic schematics.

Page 51

A Glossary of Microprocessor Terms

MICROPROCESSOR — one or several microcircuits that perform the function of a computer's CPU. Sections of the circuit have arithmetic and comparative functions that perform computations and executive instructions.

CPU — central-processing unit. A computing system's “brain”, whose arithmetic, control and logic elements direct functions and perform computations. The microprocessor section of a microcomputer is on one chip or several chips. PROM — programmable read-only memory. User permanently sets binary on-off bits in each cell by selectively fusing or not fusing electrical links. Nonerasable. Used for low-volume applications.

EPROM — erasable, programmable, read-only memory. Gan be erased by ultraviolet light bath, then reprogrammed. Frequently used during design and development to get programs debugged, then replaced by ROM for mass production.

ROM — read-only memory. The program, or binary on-off bit pattern, is set into ROM during manufacture, usually as part of the last metal layer put onto the chip. Nonerasable. Typical ROM's contain upto 16,000 bits of data to serve as the micraprocessor's basic instructions. RAM — random-access memory. Stores binary bits as electrical charges in transistor memory celis. Can be read or modified through the CPU. Stores input instructions and results, Erased when power is turned off. LSI — large scale integration. Formation of hundreds or thousands of so-calied gate circuits on semiconductor chips. Very large scale integration {VLS) involves microcircuits with the greatest component density. MOS — metal-oxide semiconductor. A layered construction technique for integrated circuits that achieves high component densities. Variations in MOS chip structures create circuits with speed and low-power requirements, or other advantages (static will damage a MOS chip).

Page 52

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 53

VII. Coin Door Maintenance

SPECIAL NOTE: If you have any questions about the coin acceptors in your game(s), please feel free to contact their manufacturers. Each manufacturer's name is PROMINENTLY imprinted on every acceptor mechanism. Metal mechanisms only: COIN MECHANISMS, INC. 817 Industrial Drive Elmhurst, IL 60126 Phone (312) 279-9150

COIN DOOR MAINTENANCE

METAL COIN ACCEPTOR MECHANISMS

Periodically, the metal coin acceptor mechanism(s) must be removed from the coin door and cleaned.

  • Make sure the power to the game is off.
  • Unlock and open the coin door.

TO REMOVE PUSH LATCHES DOWN

PLACE PEGS IN SLOTS TO REPLACE PULL MECHANISM OUT Metal and Plastic mechanisms: COINCO COIN ACCEPTORS, INC. 860 Eagle Drive Bensenville, IL 60106 Phone (312) 766-6781

. Remove the coin acceptor mechanism as shown in Figure 7-1. O Push down on the two spring loaded iatches. O While holding the latches down, pull the top of the coin acceptor mechanism toward you. C Release the latches and lift out the coin acceptor mechanism.

PUSH MECHANISM IN

Figure 7-1 Removing and replacing coin acceptor

Page 54
  • Clean the magnet of all foreign particles. See Figure 7-2. O This may be accomplished by swinging the gate open as shown in the above figure.
  • Remove the cradles and undersize levers and clean the bushings. (A pipe cleaner makes a good bushing Cleaner.) O Also clean the pivot pin.
  • Whenever needed, the coin acceptor should be cleaned with hot water and cleanser in the following manner: O Place the coin acceptor in boiling water for about ten minutes.
CAUTION: BE CAREFUL NOT TO BURN YOUR- SELF.

O Next, use a brush and kitchen cleaner to remove all remaining foreign matter from the unit. O Rinse the coin acceptor in clean boiling water. O Dry the coin acceptor thoroughly by using filtered compressed air to biow it dry.

NOTE: The reason we recommend using boiling water is that it evaporates faster than cold water and speeds drying time.

GATE OPEN AS SHOWN CLEAN MAGNET BY DRAGGING A SCREWDRIVER BLADE ACROSS SURFACE

Figure 7-2 Cleaning the metal coin acceptor

7-2

  • To lubricate the coin acceptor: 0 Use ONLY powdered graphite and put it ONLY on the moving parts of the coin acceptor. These parts are called out in Figure 7-3. O Be extremely careful to keep the powdered graphite away from paths that are traveled by the coins.
  • WARNING — DO NOT USE OIL TO LUBRICATE THE COIN ACCEPTOR.
  • Check the coin chute for obstructions such as: paper, gum, etc. Q. Reinstall the coin acceptor to the coin door. See Figure 7-1. D Place the two pegs at the coin acceptor's base into their retaining slots. O Now push the top of the coin acceptor toward the coin door until it snaps in place and is held there by the two spring loaded latches.
  • Close and lock the coin door.

APPLY POWDERED GRAPHITE HERE

CRADLE

Figure 7-3 Lubricating the metal coin acceptor

Page 55

SQUEEZE PINS TOGETHER TO UNLOCK SWING BOTH GATES OPEN

HOLDING BOTH GATES TOGETHER, PUSH UP AND PULL OUT

Figure 7-4 Opening the plastic coin acceptor

PLASTIC COIN ACCEPTOR MECHANISMS

The plastic coin acceptor mechanism(s) must be removed periodically from the coin door and cleaned.

  • Make sure the power to the game is off.
  • Unlock and open the coin door.
  • Remove the coin acceptor mechanism(s) as shown in Figure 7-1. O Push down on the two spring loaded latches. OG While holding the latches down, pull the top of the acceptor mechanism toward you. D Release the latches and lift out the mechanism.
  • Squeeze the two pins indicated in Figure 7-4 together to open the mechanism and break it down into its three basic parts. © Clean the mechanism in hot soapy water. It never rusts. O Rinse the mechanism in clean hot water and allow it to dry.

7-3 O Reassemble the mechanism (it never needs lubrication).

  • Check the coin chute for obstructions such as. paper, gum, etc.
  • Reinstall the coin acceptor to the coin door. See Figure 7-5. O Place the two pegs at the coin acceptor’s base into their retaining slots. O Now push the top of the coin acceptor toward the coin door until it snaps in place and is held there by the two spring loaded latches.
  • Close and lock the coin door.
NOTE: See Figure 7-6 for instructions on how to set the plastic coin acceptor mechanisms to either accept or reject Canadian quarters.
Page 56

ACCEPTOR CAN BE SET TO ACCEPT U.S. QUARTERS ONLY OR BOTH U.S. AND CANADIAN QUARTERS.

ss

SLIDE MAGNET TO EXTREME RIGHT (AS SHOWN) TO ACCEPT BOTH U.S. AND CANADIAN QUARTERS.

TO ACCEPT U.S. QUARTERS ONLY, SLIDE MAGNET TO EXTREME LEFT.

Figure 7-5 Changing the plastic coin acceptor to accept American or Canadian quarters.

Page 57

PLEASE NOTE:

THE INFORMATION CONTAINED IN THIS SECTION IS TOLD IN AN EASY TO UNDERSTAND MANNER AND IS INTENDED TO AID THOSE WITHOUT AN ELECTRONICS DEGREE IN TROUBLESHOOTING AND REPAIRING THEIR GAMES T.V. MONITOR.

IF YOU READ THROUGH THIS SECTION AND STILL HAVE QUESTIONS, PLEASE CONTACT YOUR DISTRIBUTOR OR MIDWAY MANUFACTURING COMPANY AT THE TOLL FREE NUMBER PROVIDED WITH YOUR GAMES PAPERS.

OUR STAFF AND OUR DISTRIBUTORS STAND READY TO HELP YOU!

THANK YOU

Page 58

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 59

Color T.V.

Color T.V Monitor

Introduction: (How to use this section of your manual.)

This section has been designed to simply familiarize you with one of the more mystical components in your game — the T.V. monitor. If you are an electronics technician who is quite knowledgeable on the subject, you may decide to just go to the schematics and start troubleshooting the defective monitor. But if you are like most people, a monitor is a T.V. set, and that means a complex doo-dad that means big buck repairs. This isn’t necessarily so. This section of the manual will acquaint you with the monitor and could just help you repair it if you feel adventurous enough to give it a try. If you have any knowledge of electronics, especially the use of a voltmeter, the repairs you can make are astonishing. Just keep in mind that ELECTRICITY CAN BE VERY DANGEROUS, SO BE CAREFUL!!

If you want to understand how a monitor works, just read the “THEORY OF OPERATION” subsection. If you wish, you can follow along with the schematics. The information is presented in a very basic manner but more complete treatment of the subject can be found in the technical sections of bookstores.

If you want to attempt to repair your monitor, it would be a good idea to read this whole section beginning to end before starting. Pay attention to all warnings

8-41 and take them seriously. The more equipment you have the better, but a low cost Volt-Ohm-Milliameter can often, do the trick. Here are the steps to take:

  • Find the symptom that matches the problems your monitor has in the “SYSTEM — DIAG- NOSIS" subsection. The diagnosis tells the circuit or area the problem may be in and possibly even the actual component causing it.
  • Once you have the circuit that is causing the trouble, read the “TROUBLESHOOTING” subsection to learn the procedure for finding the bad part.
  • Next, go to the schematic section and find the schematic that matches your monitor. It may be helpful to read the “DIFFERENCES BETWEEN MONITORS” subsection if you are unsure of which monitor you have. Use the schematic to see what parts are in the offending circuit.

That really is all there is to it. Just remember that there are some bizarre or rare symptoms not covered, or that a monitor may have two or more different problems that only a genius, the experienced, or an experienced genius can figure out. But be patient, foliow safety precautions, and remember that there is also literature available from the monitor companies through your distributor or from Midway Manufacturing Company on request. (There is a toll free number on the back side of the front cover of this manual.)

Page 60

Symptom Diagnosis

. Insufficient width or heighth: A. Horizontal line (due to VERTICAL CIR- CUIT DEFECT). Q Bad yoke. O Bad vertical output section. O Open fusible resistor in vertical section. O Bad height control. O Bad flyback. B. Vertical line (due to HORIZONTAL CiR- CUIT DEFECT). O Bad yoke. O Open width coil. O Open part in horizontal output section. . Picture spread out too far or crushed in certain areas: A. Horizontal or vertical output transistor. B. Bad component in output circuitry. . Line too close with black spacing: A. Problem in vertical section causing poor linearity. . Poor focus and convergence: A. Bad high voltage transformer (“flyback”) or control. B. Focus voltage wire not connected to neckboard terminal. . Colors missing; check: A. _ Interface color transistors. B. Color output transistors. C. Cracked printed circuit board. D. Color circuits. E. Video input jack. . Picture not bright enough: A. Weak emission from picture tube. (Turn horizontal sync off frequency and put brightness all the way up for about 15 minutes. Occasionally this cures the problem.) . Silvery effect in white areas; check: A. Beam current transistors. B. Weak picture tube emission. . Too much brightness with retrace lines; check: A. Beam limiter transistors. B. Brightness and/or color blanking controi set too high. . Increasing brightness causes an increase in size and poor focus. A. Weak high voltage rectifier or regulation (high voltage unit).

8-2 10.

11.

12.

13.

14,

15.

16.

17.

18.

19.

20. Small picture and/or poor focus: A. Low B+ voltage (power supply trouble).

Vertical rolling: A. Vertical oscillator transistor, IC, or circuit. B. No sync from logic board.

Horizontal line across center: A. Vertical output circuit is dead (see symptom No. 1. A.). B. Vertical oscillator is not putting out the right wave form. Picture bends: A. Horizontal sync needs adjusting. B. Magnetic or electromagnetic interference.

Flashing picture, visable retrace lines: A. Broken neck board. B. Internal short circuit in the picture tube (arcing). Unsymmetrical picture or sides of picture: A. Defective yoke.

No brightness, power supply operating — No high voltage for the picture tube; check: A. Horizontal oscillator. B. Horizontal amplifier and output. C. Flyback transformer (high voltage unit).

No brightness, high voltage present; check: A. Heater voltage to the tube at the neck board. B. Screen-grid voltage for the tube. C. Focus voltage. D. Grid to cathode picture tube bias.

No on voltage; check:

For AC input to the “flyback”. Horizontal deflection stages. Flyback transformer. Yoke. Power supply. moom>

No horizontal and vertical hold; check: A. Sync transistors and circuit. B. Wires and jack from logic board to the monitor. Wavey picture — (power supply defect); check: A. Transistors, diodes, electrolytic capacitors in the power supply.

Page 61
  • Moving bars in picture: A. Ground connector off between monitor and logic boards. B. Defect in the power supply (see wavy picture symptom).
  • Washed out picture (see picture not bright enough): A. Check video signal at the cathode pins with an oscilloscope. If there is about 80 volts peak to peak, the picture tube has weak emission.
  • Monitor won't turn on: A. Problem in the power supply: Check fuse, transistors, open fusible resistor.

B. Shorted horizontal output transistor. C. Defective high voltage disabling circuit. D. Crack(s) somewhere on main chassis board.

  • Can't adjust purity or convergence:

A. Use a degausser to demagnetize the picture tube carefully following your degausser's instructions. B. Picture tube defective. C. Metal foreign material is in picture tube shield. D. Nearby equipment is electromagnetically interferring. E. The poles of the earth are pulling off the purity. F. Poor focus or width of picture.

Guide To Schematic Symbols

THERMISTOR (POLARITY DOESN'T MATTER)

SYY YW

INDUCTOR, COIL, CHOKE (POLARITY DOESN'T MATTER)

(-) CATHODE

(+) ANODE

ZENER DIODE IRON CORE TRANSFORMER (SUCH AS A FLYBACK)

OL

FUSE (POLARITY DOESN'T MATTER)

CATHODE (-)

ANODE (+)

DIODE

Page 62

Fo COLLECTOR a COLLECTOR BASE ———_* BASE ———- EMITTER TT EMITTER TS

NPN TRANSISTOR PNP TRANSISTOR

WW

VARIABLE RESISTOR, POT, CONTROL RESISTOR (POLARITY DOESN'T MATTER) (POLARITY DOESN’T MATTER)

+

LINES ARE CONNECTED ELECTROLYTIC CAPACITOR

LINES ARE NOT CONNECTED CAPACITOR (POLARITY DOESN'T MATTER)

rh & GROUND

8-4

Page 63

Troubleshooting

Troubleshooting monitors requires experience, patience, and luck. The first step is to match the symptom the monitor displays to the diagnosis next to it in the “SYMPTOM-DIAGNOSIS” subsection. This will pinpoint the circuit the problem is probably in, and often the parts to check. Next, the circuit should be visually inspected to see if there are any parts broken, burned, or if something is there that shouldn't be, like a loose screw, etc. Some parts go bad before others and should be checked first. In fact, following is the general order in which parts usually go bad:

  • Semiconductors (like transistors, diodes, and integrated circuits). Fusible resistors. Electrolytic capacitors. Resistors. Capacitors and coils. OOM

Always remember that a monitor can bite like a snake. Even when it is turned off, capacitors hold voltage and will discharge it to you should you be touching chassis ground. The picture tube or CRT, itself, is a giant capacitor, so avoid the flyback anode plug hole. With the monitor on, the power supply circuit and/or the flyback, which puts out at least 18,000 volts, CAN BE KILLERS! Avoid handling power transistors (usually output transistors), yoke terminals, and other high power components when the monitor is on.

WARNING: That picture tube is a bomb! When it breaks, first it implodes, then it explodes. Large pieces of glass have been known to fly in excess of 20 feet in all directions. DO NOT carry it by the long, thin neck. Discharge its voltage to ground by shorting the anode hole to ground. Use a plastic handled screwdriver, connect one end of a wire with an alligator clip at each end to chassis ground and the other end to the metal shaft of the screwdriver. Using ONE HAND ONLY (put the other in your pocket) and touching ONLY the plastic handle of the screwdriver (DO NOT TOUCH THE METAL SHAFT) stick the blade of the screwdriver into the anode hole. Be prepared for a fairly loud pop and a flash. The longer the monitor has been turned off, the smaller the pop and dimmer the fiash. But BE CARE- FUL, picture tubes will hold a very

8-5 healthy charge for at least a week if not longer. Even after you've discharged it once, it may still carry a residual charge. It’s better to be too careful than dead, which is why electronic equipment always carries stickers referring servicing to qualified personnel. Handle the side with the viewing screen against your chest when changing it. ALWAYS wear safety goggles when handling the picture tube.

To maintain the safety and performance of the monitor, always use exact replacement parts. For instance, the wrong components in the power supply can cause a fire, or the wrong color transistor may give a funny color to the picture. Service your monitor on a nonconductive firm table like wood, NOT METAL, and take off all of your jewelry just in case. With all this in mind, you are ready to begin troubleshooting.

Observe the picture carefully. Try to vary the appropriate control that would most likely affect your particular symptom. For example, if there is poor brightness or no picture, try turning up the brightness or contrast control. If the controls have no effect at all, chances are there is trouble with the control itself, the circuit it controls, or a nearby circuit that may be upsetting voltages. Go to the list of symptoms and determine with the schematic where the bad circuit is.

CAUTION:

Keep in mind that capacitors hold a charge as can the picture tube (for at least a week and usually longer), and could shock you.

First, check for obvious visual defects such as broken or frayed wires, solder where it is not supposed to be, missing components, burned components, or cracked printed circuit boards. If everything looks good up to this point, make sure that diodes, electrolytic capacitors, and transistors have their leads connected in the right polarity as shown on the schematic and the circuit board. Turn on the power and measure the voltages at the leads of the active devices such as tubes, transistors, or integrated circuits. Any voltage that does not come within at least 10% to 15% of the voltage specified on the schematic indicates either a problem with that device or a component connected with it in the circuit. The next step is to use the ohmmeter to narrow down the fieid of possible offenders.

Page 64

To test a transistor, one lead of the ohmmeter is placed on the base; and the other lead placed just on the emitter, then on the collector. A normal transistor will read either high resistance (infinite), or little resistance (400 to 900 ohms), depending on the polarity of this type transistor. Then the leads should be switched, one remaining on the base, and the other switched from the emitter to the collector. Now the opposite condition should result: the resistance should be infinite if it was lower when the other lead was on the base. Consistantly infinite readings indicate an open, and a short is demonstrated by 0-30 ohms on most of these test readings. Finally, place one lead on the collector, then the other on the emitter. No matter which lead is used, there should be infinite resistance. Any lower reading, such as 50 ohms (which is typical on a bad transistor), indicates a short. This all sounds pretty confusing, but a little experience on a good transistor will make you an expert in no time. Usually, the lowest ohmmeter setting is used for testing transistors. Once in a great while a transistor may check out good on this test, but may actually be “leaky” or break down only on higher voltages. If in doubt, change it. It is also wise to check the transistor out of the circuit just in case some component in the circuit is affecting the ohmmeter reading. A diode is tested like a transistor except it only has two leads. Again, there should be high resistance one way and little resistance the other. If it tests bad, take one lead out of the circuit in case some componentis messing up the ohmmeter reading.

NOTE: DO NOT leave soldering equipment on the leads too long since all semiconductors, especially integrated circuits, are easily destroyed by ‘heat.

Without special equipment, integrated circuits are checked by verifying the proper DC voltage on the pins and the correct AC wave form using an oscilliscope. BE CAREFUL: Shorting their pins can easily destroy them. Resistors are checked with an ohmeter and should usually be within ten percent of the value stated on them and on the schematic. You may have to desolder one lead from the printed circuit board. If you wreck the foil on the board, carefully solder a small wire over the break to reconnect the conductive foil. Capacitors are tricky. Their resistance goes up when checked with an ohmmeter which shows a charging action. As they suck up current from the meter, the

voltage goes up and so does the resistance. If you are

sure a particular circuit is giving you a problem and everything else checks out O.K., Electrolytic capacitors are prime suspects. Substitute a new one and keep your fingers crossed.

Theory of Operation

To understand what goes on inside the monitor, large general groups of circuits will be examined instead of laboriously analyzing the branches and small circuits that make up these groups. This will help avoid confusion and aid in a basic, concrete, knowledge of what makes up a monitor.

THE POWER SUPPLY — The AC going to the monitor from the game transformer is just like the voltage and current from your wall outlet. It jumps up and down going positive and negative sixty times a second. But a monitor needs nice, smooth DC; direct current, not alternating. So diodes chop up the AC and a big electrolytic capacitor filters it out to make it even smoother. Since the monitor is a big piece of electronic equipment, with many circuits demanding a lot of power from the power supply, there are also zener diodes and transistors to help maintain a nice, constant, smooth voltage so that the monitor circuits don't jump around. And this is what happens when you see a wavy picture. There is AC creeping

8-6 through the power supply, so it must be malfunctioning. If the voltage from the power supply is too low, the other circuits will be starved for power and you may see a small, wavy picture, or noneatall. Some circuits receive voltages that are higher than what the power supply should put out. But they come from the flyback transformer which will be discussed later.

THE INTERFACE SECTION OF THE CHASSIS — The interface section of the chassis is fairly easy to identify. It is right by the place where the video jack(s) from the logic board(s) plug into. There are sets of transistors that receive the separate red, green, blue, and sync information from the cables that come from the logic boards. The circuits jack up the voltage and match impedances, or in other words, prepare the logic board outputs for the circuits that will really amplify them for the output devices such as the yoke in the case of the sync, or the picture tube that shows the colors.

Page 65

An interesting aside is that our sync is composite negative sync. That means two things:

  • The sync is a negative going wave form.
  • There are two pulses going at different speeds over the same wire: a. Vertical wave forms at 60 times per second (or Hertz) and b. Horizontal wave forms at about 15,750 times per second (Hz). The sync is amplified by a sync amplifier transistor and sent on its way to the oscillators. The sync or timing information will be explained along with the oscillator shortly. The color information is sent via wires to the neck board where the main amplification occurs. This will also be discussed later.

VERTICAL AND HORIZONTAL DEFLECTION— After the sync signal is amplified by the sync amp, it goes to two different sections, the vertical and horizontal circuits. Basically, the sync signals are for timing so the picture doesn’t mess up since it is assembled like an orderly jigsaw puzzle, but so fast that you can't see the electron beams for each color painting the picture on the screen. This will all become clear soon. For now, we will follow the 60 cycle component of the sync as it goes on its journey to the deflection yoke. The 60 cycle pulse goes to the vertical oscillator to make sure this circuit goes back and forth (or oscillates) at 60 times a second. Without this pulse keeping the circuit at the correct speed, it may get lazy and oscillate at 58 cycles or lower, or get ambitious and oscillate at 62 cycles or higher. At the wrong speed, the picture will start to roll up or down. A Wells Gardner 13” (K4806) or 19” (K4906, K4956) color monitor uses an integrated circuit for its sync section. An Electrohome 13” or 19” color monitor uses an integrated circuit |C501 for its sync section. Wells Gardner uses HA11423 and Electrohome uses HA11244. These ARE NOT interchangeable! The idea is all the same. The output to the vertical amplifying transistors for ail monitors must form a sawtooth wave form, sort of like a bunch of pyramids, racing through the yoke’s vertical coils at 60 times a second. Along the way to the output transistors, the 60 cycle pulse is shaped and amplified to do the job: the yoke magnetically pushes the electron beam to fill the screen out sideways looking at the screen with the greatest length going up and down. Or viewing the screen sitting like a home television set, the amplified vertical output fills the screen up and down. Watching a monitor like this, seeing only a horizontal line means a problem with the vertical coils of the yoke or anything from the vertical output section on back to the oscillator. The horizontal section is very similar with a few exceptions. The horizontal wave shape is more like a square and has a frequency of 15,750 cycles a second. Both Wells Gardner and Electrohome use the other side of their respective integrated circuits for the horizontal circuitry. !f the oscillator isn’t going at the correct speed, the picture may move sideways, start to slant, or tear up with slanted thin figures. With both the vertical and horizontai of all monitors, there are variable resistors that change the speed of the oscillators up and down. This way you have controls that can make the correct frequencies to keep the electronic jigsaw puzzle nicely locked in place. If you're driving in a car and next to you someone else is driving their car at exactly the same speed, it will appear that they are not moving. And this is why the sync frequency and the oscillator’s frequency must match, so the picture doesn’t appear to move. The correct wave form is shaped and amplified in the circuitry just like in the vertical section. But the horizontal output transistor is a large power transistor and not only serves to give current to the horizontal yoke windings, it also feeds the flyback transformer.

THE FLYBACK TRANSFORMER (OR HIGH VOLTAGE UNIT) — The picture tube needs high voltage to light up, and the power supply can’t meet this demand. The flyback transformer receives current alternating at about 15,750 times per second from the horizontal output transistor. The “flyback” jacks up its input voltage and puts out a higher voltage alternating at the same speed. But, in your “flyback” there are diodes that chop up the alternating voltage to make it asmooth DC output just like in the power supply. This is what goes through that thick red wire to your picture tube. THIS AREA HAS ABOUT 18,000 VOLTS ON IT AND IT CAN KILL YOU!

The “flyback” may be dangerous, but it is also generous. It has extra output windings which give voltage to the heater pins of the picture tube, voltage for the vertical deflection circuits, and picture tube screen-grid voltage. So in a way, the high voltage “flyback” is like a second power supply.

COLOR CIRCUITS — The color circuits are pretty straight forward. The signals go into the interface section where some amplification and impedance matching occurs. These circuits are pretty sparse and simple. Each color just has two transistors and a diode with some resistors and capacitors. From here, the AC color signal is sent by wires to the neck board. The color output circuits are on the neck board. The color signals going to the transistors are controlled by two variable resistors called drive controls. There are only two, one for the red and one for the green.

Page 66

The blue doesn't have one. In the emitter part of each transistor is another variable resistor that is the cut off control. These controls vary the amount of amplified AC signal that goes to the cathodes of the picture tube. The more signal, the more color. The bases of each of these transistors are connected together and are all connected to the blanking and beam limiting transistors which are in the interface section. The beam limiter helps control the brightness level, and the blanking transistor rapidly turns the picture tube on and off so that retrace lines don’t show up on the screen. By turning up the brightness on a good monitor, these four to six retrace lines can be seen slanting diagonally across the picture.

PROTECTION CIRCUIT — To protect the high voltage section against voltages that are too high coming from the power supply which could cause X-rays to be emitted from the “flyback”, a circuit senses the higher power supply voltage, and using a transistor, turns off the horizontal oscillator. Since the horizontal oscillator doesn't work, the horizontal output transistor has nothing to feed the “flyback” which in turn has nothing to feed the picture tube. The monitor will be silent, have no picture, and will appear to be off. But don't be fooled. There is still that excessive amount of voltage coming from the power supply. To find out, check at pin two of Wells Gardner's C501 and emitter of X04 for the Electrohome monitor. Here are the voltages you should receive: Wells Gardner = 130VDC Electrohome 120VDC The best place to measure this voltage on an Electrohome monitor is at a pin marked B1 on the chassis. This is because a 13 inch color Electrohome monitor, The G07-FBO or GO7-902, has an integrated circuit and very little else in the power supply. Still, there should be 120VDC at B1.

THE PICTURE TUBE (OR CRT) — The picture tube or CRT is an output device. In other words, the end result of the circuit's work is displayed by this part. Actually, the output of other circuits is in the neck of the picture tube. First, there is the heater. The heater boils off electrons from the cathodes so that they (the electrons) shoot up to the screen to excite the phosphors so that the three phosphors emit three colors of light. The cathodes are next, and again they emit electrons to turn on the tube phosphors, making it glow. The cathode can arc or short to the heater resulting in no picture and a defective picture tube. Next come the grids. The first grid is grounded. The following grid is the screen grid which receives about 300VDC depending on the brightness setting. The next grid closest to the picture tube screen is the focus grid which gets about one fifth the amount of voltage that is applied to the picture tube anode. After jetting from the cathode through all these grids, the electrons speed through a mask, a sheet of material with tiny holes, and then excite the tiny dots of phosphor in the inside surface of the picture tube screen. The green electron gun (or cathode and circuitry) spits out electrons which head for the green phosphors only. The same goes for the red and blue guns, The way the phosphor light blends determines the color seen. Should these electron beams become too intense, they may burn the phosphor. With the monitor off, this can be seen as a dark permanent image of the video information on the tube screen.

Differences Between Monitors

The easiest way to identify the brand of monitor you are working with, assuming you can’t find the brand name written on it anywhere, is to check the color of the suction cup type insulator that houses that dangerous anode plug on the CRT. Both monitors use a red wire but the Wells Gardner anode cup is BLACK while the Electrohome anode cup is LIGHT GRAY. Unfortunately, “call-out-numbers” for parts, circuit layout, and even circuit design are similar enough to confuse the average observer. Let's say you have an Electrohome that isn’t working. No problem. You can scavenge parts from an old broken up one that you may have around. Now let's say you have a Wells Gardner that isn’t working. STOP! This could bea problem. There are3 different types of Wells Gardner K4900 SERIES monitors in the games. Here are ways to identify them.

K4906 (1st TYPE) — This monitor's identifying tags have BLACK ink printed on a white background. There is NO Vertical Damping Control. (This Controt would be next to the Vertical Hold Contro! but this area is jumpered with a small wire instead. K4906 (2nd TYPE) — This monitor's identifying tags have RED ink printed on a white background. There IS a Vertical Damping Control next to the Vertical Hold Control. The Damping Control provides a few more lines on the top of the monitor screen (monitor viewed as a normal T.V. would be) for any video game that may need these lines to fit the picture on the

Page 67

screen. Moving the Control may distort the top part of your picture (or the side, depending on the game and how the monitor is mounted) so go ahead and move it if you are having this type of problem. To accommodate this new feature, there are a few circuit changes. ONE MAJOR DIFFERENCE BETWEEN THESE TWO VERSIONS OF THE K4906 IS THE YOKE. They look the same but notice the part numbers: K4906 WITHOUT the Damper Control: 2021111201 K4906 WITH the Damper Control: 2021111258 Since the companies like to change part numbers at the drop of a hat, the best thing to do is to request whatever part number is written on your yoke. If you should get the wrong yoke, the results will be: Picture distortion. Excessive brightness. Too much or too little vertical picture size. K4956 (3rd TYPE) — This monitor is identical to the K4906 WITHOUT the Damper Control EXCEPT the picture tube is vertically mounted and there is an additional small P.C. Board mounted on the monitor where the yoke plugs in. This monitor is used on some Cocktail Table games where the picture has to flip for the second player. Generally speaking, some games flip the picture image via the logic board programming but this monitor is used in games that flip the picture image via generation of a small signal voltage which is sent to the extra P.C. Board on this monitor. This signal voltage causes relays on this extra P.C. Board to flip the picture by reversing the horizontal and vertical signals to the yoke pins. What kind of problems can this extra P.C. Board cause? If the relays become defective, the picture won't flip. If the P.C. Board gets cracked you may have a horizontal line on the screen, a vertical line on the screen, or maybe just a dot in the center of the screen. Of course, the logic board could be defective and not sending the signal to flip the picture. In any case, some people feel that using relays is cheaper, simpler, and more reliable, so this is an advantage.

CONTROLS YOU MAY NOT TOUCH Basically, on the Electrohome monitor, you can move any control you want EXCEPT for the B1 control. This sets the power supply voltage (ideally at 120 VDC) and is located right behind VERTICAL HOLD. The 13” Electrohome DOES NOT have this control. It may also be wise not to move the VERTICAL LIN- EARITY since this distorts the picture and is hard to reset perfectly. If you do move it, turn on the Cross Hatch Test Pattern of your game and try to get the squares to the point where they are equal in size by readjusting this Linearity Control.

On the Wells Gardner monitor, brightness is adjusted by the “BLACK LEVEL” Control which is right next to the Horizontal Frequency Control. Under the Focus Control is the “SCREEN” Control which youDO NOT touch. Yes, this control does adjust the brightness, but it is used to set the CRT bias and is adjusted at the factory. When Wells Gardner sets it, they mark the position with a black mark on the knob. If you move it, be sure to realign the mark and THEN set the BLACK LEVEL Control to the brightness you desire. So, other than the SCREEN control, you may adjust any of the controls.

Parts Interchangeability

Some parts can be interchanged on all of the monitors. Here are the rules:

  • You CAN swap any resistor between monitors that has the same resistance, wattage rating, and tolerance. You CAN swap any capacitor between monitors that has the same capacitance and voltage rating. You CAN swap many of the parts between the 19” and the 13” versions of each manufacturer's monitor. BUT, be certain to compare the manufacturers’ part numbers to be positive the parts you want to interchange are identical. BE SURE you have read the section DIFFERENCES BE- TWEEN MONITORS which was covered earlier. You CANNOT swap any picture tubes between monitors! In the past you could, but Wells Gardner is now using a new monitor. When ordering a replacement picture tube, ALWAYS SPECIFY THE PICTURE TUBE NUMBER! You CANNOT change any part that is a safety part, one that is shaded in gray on the schematic; it MUST be IDENTICAL to the original. To do otherwise IS DANGEROUS. For instance, the 13 inch Electrohome (G07-902) monitor “flyback” looks identical to the 19 inch Electrohome (G07- 904) monitor “flyback”. In fact, there is evena 19 inch Electrohome (G07-905) monitor (which is an obsolete model) with a similar looking “flyback”. NONE OF THESE ARE INTER- CHANGEABLE! You CAN change any of the parts between the G07-904 and G07-907. They're essentially the same monitor except that the G07-907 has a vertically mounted picture tube. If there is any doubt about what parts can be swapped between each manufacturer's 19 inch and 13 inch models, compare the manufacturer's part number between each one. If they match up, they are the same part.
Page 68

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 69

Power Supply Voltage and Symbols

Symbol | Voltage Operating Circuit

® tsv | Vert. Osc. Sync Blanking CRT Cut-Off

a 130V Horiz. Osc. Horz. Drive Horz. Output Vert. Output

| Video Output

1VIDIV 200uSECIDIV

TP.31 DC COUPLED BOTTOM LINE=0 VOC

2VIDIV 200MSECIDIV

LC. 301, PIN 3

20VIDIV SMSECIDIV

LC. 301, PIN 13,

1VDIV 200uSECIDIV 351 COLLECTOR

20VIDIV 10uSECIDIV

34023

SV/DIV 20uSECIDIV

F

1VIDIV 20u SEC/DIV

TP.31, AC COUPLED

1VIDIV 200uSECIDIV

NEGATIVE SIDE OF C303

2VIDIV SMSECIDIV oggroomecnmneremmarmmcneage 19” COLOR MONITOR SCHEMATIC DIAGRAM

MODELS 19K4901, 19K4906, 19K4951, 19K4956

AN

SERVICE TECHNICIAN WAR

X-RAY RADIATION PRECAUTION:

THIS PRODUCT CONTAINS CRITICAL ELECTRICAL AND MECHANICAL PARTS | ESSENTIAL FOR X-RAY RADIATION PROTECTION FOR REPLACEMENT PURPOSES, USE ONLY TYPE PARTS SHOWN IN THE

a201 Yaeo 2scisiscvy. | 2s¢945

O.SIDIV SMSECIDIV

0.5/DIV 20u SECIDIV

R301 LC. 301, PIN 15

Ie 301

Halia23

2VIDIV 10uSECIDIV

1VDIV 2MSECIDIV EgAUSSING COIL OSCILLOSCOPE WAVEFORM PATTERN The waveforms shown are as observed on the wide band oscilloscope with the monitor turned to a reasonably strong signal and a normal picture. The voltages shown on each waveform are the approximate peak amplitudes. If the waveforms are observed on the oscilloscope with a poor high frequency response, the corner of the pulses will tend to be more rounded than those shown and the amplitude of any high frequency pulse will tend to be less.

CAUTION: FOR CONTINUED SAFETY, REPLACE SAFETY CRITICAL COM- PONENTS ONLY WITH MANUFAC- TURER'’S RECOMMENDED PARTS. AVERTISSEMENT: POUR MAINTENIR LE DEGRE DE SECURITE DE L’APPAREIL NE REMPLACER LES COMPOSANTS DONT LE FONCTIONNEMENT EST CRITIQUE POUR LA SECURITE QUE PAR DES PIECES RECOMMANDEES PAR LE FABRICANT.

2401 9.402 393, RED OUT GREEN OUT BLUE OUT 28C2068.8/L85K 25C2068L.B/ BEK 25C20681.8/ £8K| 2SCISI4BVC/CVE 2SCIBISAVELVE 2SCIBI4BVC/CVC ( ‘|

|;isiaseS, Gee mom|SrovutezeZ
aiozs||CSafeoheAca

pee i= a Ne

cal:Bs eee afoo) fe |

lve, 270

0Sa05Tex

P poly 3s6. ein fhe ay F deed?

(G.pRivE} at P00 | (RcuTOFF] [G.cUTOFF]

SYNC AMP VOsC H.08C :

BP. 5). HOR ORIVE seces?>) 2gceaa,

  • ieceeoen

r Be ses, he SE BP ae sade} | ete.

sicoat 2y oe”
3309(per) =e9302(ese

ge PA atten \ /2sc2073 S/ seers _

Res) | S TOBA bt ay our does soav T38e

laews Tene ait sane ase | 19908 PS s7n80v

  • size #$80v

DEF LYOKE

  • K4901D, K4906D, K4951D 5833 k4956B a-10
Page 70

REPLACEMENT PARTS LIST This monitor contains circuits and components included specifically for safety purposes. For continued protection no changes should be made to the original design, and components shown in shaded areas of schematic, or A* on parts list should be replaced with exact factory replacement parts. The use of substitute parts may create a shock, fire, radiation or other hazard. Service should be performed by qualified personnel only.

MAIN BOARD

Ref. No.Part No.DescriptionRef. No.Part No.Description

RESISTORS RESISTORS (CONT.)

R201203x6500-645,1K Ohm, 5%, 1/4W CarbonR369203x5602-329680K Ohm, 5%, 1/2W Comp.
R202203X6500-52330 Otim, 5%, 1/4W CarbonR370203X6501-00233K Ohm, 5%, 1/4W Carbon
R203203X6500-405100 Ohm, 5%, 1/4W CarbonR371203x9014-5841K Ohm, 5%, 1W Metal Oxide
R204203X6700-327100 Ohm, 5%, 1/2W CarbonR372203X9101-11912K Ohm, 5%, 1W Metal Oxide
R205203X6700-421270 Ohm, 5%, 1/2W CarbonR375203X6700-7636.8K Ohm, 5%, 1/2W Carbon
R206203X6500-540390 Ohm, 5%, 1/4W CarbonR376203X9104-404270 Ohm, 5%, 2W Metal Oxide
R207340X2201.934200 Ohm, 5%, 1/4W CarbonR377203X6500-447150 Ohm, 5%, 1/4W Carbon
R208203X6500-540390 Ohm, 5%, 1/4W CarbonR378203X6500-88610K Ohm, 5%, 1/4W Carbon
R209340X2201.934200 Ohm, 5%, 1/4W CarbonR379203X6500-88610K Ohm, 5%, 1/4W Carbon
R210203X6500-540390 Ohm, 5%, 1/4W CarbonR380203X6500-865,8.2K Ohm, 5%, 1/4W Carbon
R211340X2201.934200 Ohm, 5%, 1/4W CarbonR381203X6500-7242.2K Ohm, 5%, 1W Metal Oxide
R214203X6500-6451K Ohm, 5%, 1/4W CarbonR383203x9014-387150 Ohm, 5%, 1W Metal Oxide
R215203X6501-126400K Ohm, 5%, 1/4W CarbonR502203X6500-88610K Ohm, 5%, 1/4W Carbon
R216203X6500-6451K Ohm, 5%, 1/4W CarbonR503204x 1700-535150 Ohm, 5%, 15W Metal Oxide
R217203X6500-405100 Ohm, 5%, 1/4W CarbonR504203x9014.26747 Ohm, 5%, 1W Metal Oxide
R218203X6500-645,1K Ohm, 5%, 1/4W CarbonR505203X6501-2092.2K Ohm, 5%, 1/4W Carbon
R219203X6501-126400K Ohm, 5%, 1/4W CarbonR506203X9104-10515 Ohm, 5%, 2W Metal Oxide
R220203X6500-6451K Ohm, 5%, 1/4W CarbonR507203x5602-185330K Ohm, 5%, 1/2W Comp.
R221203X6500-405,100 Ohm, 5%, 1/4W CarbonA*R601204x 1625-0583.3 Ohm, 5%, 10W WW
R222203X6500-7623.3 Ohm, 5%, 1/4W CarbonR701203X9105-1412.2 Ohm, 5%, 2W Metal Oxide
R224203X6500-16910 Ohm, 5%, 1/4W CarbonR702203X6206-4412.2 Ohm, 5%, 1/2W Carbon
R225203X6500-16910 Ohm, 5%, 1/4W CarbonR201204x2070-0722k Ohm-B Semi
R226203X6500-16910 Ohm, 5%, 1/4W CarbonR301204x2070-084
R227203X6501-04447K Ohm, 5%, 1/4W CarbonVR303204X2070-055,
R228203X6500-6451K Ohm, 5%, 1/4W CarbonR351204x2070-072
R229203X6700-421270 Ohm, 5%, 1/2W CarbonVR352204X2070-0722K Ohm-B Semi-Fixed
R230203X6500-8638.2K Ohm, 5%, 1/2W Comp.
R231203X6500-8638.2K Ohm, 5%, 1/2W Comp.
R232203X6500-8638.2K Ohm, 5%, 1/2W Comp.
A233,203X6500-468180 Ohm, 5%, 1/4W Carbon
R234340X2820-93482 Ohm, 5%, 1/4W CarbonCAPACITORS
R235340X2820-93482 Ohm, 5%, 1/4W CarbonC201203X0014-0881000 uF, 16V, Electrolytic
R236340X2820-93482 Ohm, 5%, 1/4W CarbonC202202X7200-064330 pF, 500V, Ceramic
F301203X6500-508270 Ohm,5%, 1/4W CarbonC203202X7200-043220 pF, 500V, Ceramic
R302203X6500-8638.2K Ohm, 5%, 1/4W CarbonC204202X7200-043220 pF, 500V, Ceramic
R303203X6500-8638.2K Ohm, 5%, 1/4W CarbonC205203X0014-076470 uF, 16V, Electrolytic
F304203X6500-7242.2K Ohm, 5%, 1/4W CarbonC206203X1810-149,0.1 uF, 125V Mylar
R305203X6500-8426.8K Ohm, 5%, 1/4W CarbonC207349X2232-109022 uF, 100V Mylar
R306203X6003-2017.5K Ohm, 2%, 1/4W Carbon301203X0014-065330 uF, 50V Electrolytic
R307203X6500-825,5.6K Ohm, 5%, 1/4W Carbon302203X1600-5630.033 uF, 50V Mylar
R309203X6500-965,22K Ohm, 5%, 1/4W CarbonC303203X0629-0373.3 uF, 50V Electrolytic
R310203X6500.98839K Ohm, 5%, 1/4W CarbonC304203x1600.3660.068 pF, S50V Mylar
R311203X6500-7623.3K Ohm, 5%, 1/4W Carbon306203X0412.01222 uF, 16V Tantal
R312203x9014-7414.7K Ohm, 5%, 1/4W CarbonC307203X1600-6340.033 UF, SOV Mylar
R313204X 1450-5371K Ohm, 5%, 5W CarbonC308203X0025-1743.3 UF, 50V Electrolytic
R314203X6500-481220 Ohm, 5%, 1/4W Carbon309203X1207-1000.068 UF, 100V PP
R315,203X6500-16910 Ohm, 5%, 1/4W CarbonC310203X0629-06110 uF, 100V Electrolytic
R316203X6500-7623.3K Ohm, 5%, 1/4W CarbonC311203X0041-02510 uF, 160V Electrolytic
R317203X6700-10712 Ohm, 5%, 1/2W Carbon312202X7050-2484000 pF, 500V Ceramic
R318203X6500-540390 Ohm, 5%, 1/4W CarbonC313203X0040-05247 uF, 160V Electrolytic
R319203X6500-6451K Ohm, 5%, 1/4W CarbonC314203X1201-265,0.033 uF, 200V PP
R320203X6501-00233K Ohm, 5%, 1/4W Carbon315203X0629-0231 uF, 50V Electrolytic
R321203X6501-224270K Ohm, 5%, 1/2W CarbonC351203X0629-0231 uF, 50V Electrolytic
R322203X6500-88610K Ohm, 5%, 1/4W CarbonC352203X0619-04547 uF, 25V Electrolytic
R351203X6500-88610K Ohm, 5%, 1/4W CarbonC353203X1190-0150.0082 pF, 50V Mylar-PP
R352203X6500-7853.9K Ohm, 5%, 1/4W CarbonC354203X0619-04547 uF, 25 Electrolytic
R353203X6501-08668K Ohm, 5%, 1/4W CarbonC355203x1600-3660.0068 pF, 50V Mylar
R364203X6500-7623.3K Ohm, 5%, 1/4W CarbonC356202X7050-4830.01 uF, 500V Ceramic
R955203X9205-143,6.8K Ohm, 5%, 3W Metal OxideC359202X8065-606100 pF, 500V Ceramic
R358203X5601-87856K Ohm, 5%, 1/2W CarbonC360202X7050-3660.0033 pF, 500V Ceramic
R360203X6500-561470 Ohm, 5%, 1/4W CarbonC361202X7050-4830.01 uF, 500V Ceramic
R361203X6500-88610K Ohm, 5%, 1/4W CarbonC362202X7203-0320.01 uF, S0V Ceramic
R362203X9014-6451.8K Ohm, 5%, 1W Metal Oxide30363203x1270-9118700 pF, 1.5 KV PP
R363204X1527-7513.9K Ohm, 5%, 7W Metal Oxide#0365203X1201-2650.33 uF, 200V PP
R364203X6500-24622 Ohm, 5%, 1/4W CarbonC366203X0019-02622 uF, 25V Electrolytic
R365203X6501-00233K Ohm, 5%, 1/4W CarbonC367202X8065-1626 pF, 500V Ceramic
R367203X6500-88640K Ohm, 5%, 1/4W CarbonC368202X7203-0320.01 uF, 50V Ceramic
R368203X5602-185,330K Ohm, 5%, 1/2W Comp.C372203X1207-1250.1 uF. 100V PP

MAIN BOARD (CONT.)

Ref. No.Part No.DescriptionRef. No.Part No.Description

CAPACITORS (CONT.) SEMICONDUCTORS (CONT)

380202x7200.087470 uF, 500V Ceramic206200x3181-523Transistor (NPN) 28C1815GR
C501203X1810-1490.1 uF, 125V Mylar207200x3181.523Transistor (NPN) 2SC1815GR
4 0502202X7050-2821500 pF, 500V Ceramic208200x3181-523Transistor (NPN) 28C1815GR
40503202X7810.2142200 pF, 125V Ceramic209200X3181-523Transistor (NPN) 2SC1851GR
A.c504202X7810.2142200 pF, 125V Ceramic210200x3181-523Transistor (NPN) 28C1851GR
C505203x0220-075560 uF, 200V Electrolytic301200x3181-523Transistor (NPN) 28C1851GR
C506203X0040.03422 uF, 160V Electrolytic302200X3207-306Transistor (NPN) 28C2073LBGL2
507203X0041.05747 uF, 160V Electrolytic303200X3207-306Transistor (NPN) 2SC2073LBGL2
701203x0019.0921000 uF, 25V Electrolytic9351200X3248.217Transistor (NPN) 28C24828K
702203X0634.06110 uF, 100V Electrolytic352200X4589-802Transistor (NPN) 28D898B
703202X7050-2481000 pF, 500V Ceramicann200X2300.033IC HA11423
1C501200X2600-183IC STR381

SEMICONDUCTORS

0203201X2010-159Diode, 1$2076-27
D204201X2010-159Diode, 1$2076.27TRANSFORMERS &COILS
D205201X2010-158Diode, 1$2076.2713512O1X4710-134Coll, (RF Choke)
D206201%2010-159Diode, 1$2076-27L352PiliteteedGoll, Horizr Size
0207201X2010-159Diode, 1S2076-27Lot110004 007Coll, Adg.
D:201X2010-1:f1351202X1300-080Transformer, Hor. Drive
208101X2010-159Diode, 1$2076-27‘
D209201X2010-159Diode, 1$2076-27Aw 1352iHvAnit 4°11
D301201X2010-165Diode, S881
0302201X2010-159Diode, 1S2076-27MISCELLANEOUS
0303201X2010-159Diode, 182076-27AFS501204X7120-073Fuse, 4 Amp. 125V
0308201X2120-009Diode, RH-IV9402206X5008-632Recep W Wire 3P-M-BG
D305201X2120-009Diode, RH-IVP201204X9600-466Plug, PWB 3P-J
D306201X2010-159Diode, 1S2076-27P202204X9601-477Plug, PWB 6P-Q
D501201X3120-216Diode, RM-1AVP401204X9600-298Plug, PWB 4P-B
D502201X3120-216Diode, RM-1AV501204X9800.249Plug, PWB 2P-B
4.0503201X3120-216Diode, RM-1AV601204X9600-304Plug, PWB 4P.C
D504201X3120-216Diode, RM-1AVTH5O1201X0100-112Thermistor
0505201X3120-216Diode, RM-1AV
D506201X3120-216Diode, RM-1AV
D701201X2130-234Diode, RU:2VFINAL ASSEMBLY PARTS
D702201X2120-009Diode, RH-1VAm 88x0138-50619VLTP22 Pix Tube
201200x3181-523Transistor (NPN) 2SC1815GR205X8800-158,Lateral/Purity Assembly
202200X3181-523Transistor (NPN) 2SC1815GRA 202X1111-201Yoke Deflection
2203200x4056-260Transistor (PNP) 29A562-Y-TM204X9301-255CRT Socket
204200X4056-260Transistor (PNP) 2SA562-Y-TM291X5004.262Automatic Degaussing Coil Unit
208200X4056-260Transistor (PNP) 2SA562-Y-TM

NECK BOARD RESISTORS CAPACITORS

aot203X6000-729220 Ohm, 5% 1/4W Carbon401202X7050-2691200 pF, 500V Ceramic
Rao2203X6500-540390 Ohm, 5% 1/4W CarbonC402202X7050-2481000 pF, 500V Ceramic
R403203X6000-661820 Ohm, 5% 1/4W CarbonC403202X7050-2481000 pF, 500V Ceramic
aod203X6000-729220 Ohm, 5% 1/4W CarbonC404202X7050-2821500 pF, 1.5KV Ceramic
R405203X6500-540390 Ohm, 5% 1/4W CarbonC405202X7050-4830.01 uF, 500V Ceramic
R406203X6000-661820 Ohm, 5% 1/4W Carbon
R407203X6000-729470 Ohm, 5% 1/4W Carbon
R408203X6000-998270 Ohm, 5% 1/4W CarbonSEMICONDUCTORS
R409203X6000-661820 Ohm, 5% 1/4W Carbon
Rar0oaxer04-82415K Ohm, 8% 2W MO. Formingaz200x208 800Tanssto (NPN) 280200818
Bat209910402415K Ohm, 8% 2W M.0. Forming403200X3206-800Transistor (NPN) 28C2068LB
Ratz203X9104-82415K Ohm, 5% 2W M.O. Forming
Ra13203X6000-9982.7K Ohm, 5% 1/2W Comp.
Rata203x6000.9982.7K Ohm, 5% 1/2W Comp.
Ra15203X6000-9982.7K Ohm, 5% 1/2W Comp.440MISCELLANEOUS
Ra16203X9105-1542.2 Ohm, 5% 2W Metal OxidePadePayeeenrorybasiTali
Ra19203X6500-7412.7K Ohm, 5% 1/4W Carbon042000-254Plug, PWB 3P-A
R420203X6500-7412.7K Ohm, 5% 1/4W CarbonLs2oanoe00 481Plug, Pin 1P-D
7P701204X9601-020Plug,PWB 4P-E
Ra2t203X6500-7412.7K Ohm, 5% 1/4W Carbon9,
R401204x2115.014500 Ohm, -B Semi-Fixed
vRao2204x2115.014500 Ohm, -B Semi-Fixed
VvR403204X2115-0065K Ohm, -B Semi-Fixed
vRao4204X2115-0065K Ohm. -B Semi-Fixed
R405204X2115-0065K Ohm, -B Semi-Fixed
Page 71

_ FoWeR Wa aTSE, X901 POWER DRIVE 2SC 2688 Blue anEen RED X101.xI03 ond xI05 VIDEO AMP. 25¢454 X102.X104 and x106 VIDEO AMP. 2SA673¢ TOce Ne ES OUT —T 2SC26I1 or 2SCIB4V ”

| @ af |

  • x98 | Beuo6a, esciasa > A Px301,x302,x808,x308 'SYNC ap [28CaSac or eecieas

ACIZ0V 60H2/50Hz #10% aoe one wove] ©

138% [rvic ca ww cur erry Tiere fete eer stir t/a) ico

Tit

SU -1133A MAIN PCB ASSY ese t i i i \ ior DEFLECTION YOKE

X701_X-RAY PROTECTOR 2scasae or 25ci685 500 1.01 28ciso7 28c26iI or xr wour iA zscesTiv 250898 or us qussente en ne sree C26i0BK 250869 or 280820

00-4147-04 G07-CBO Schematic Notes Unless otherwise specified Resistance: (2) (K-*K2, M-~MQ), 1/4 (W) carbon resistor Capacitance: 1 or higher» (pF), less than 1-> (yF) working voltage -» 50 (V) ceramic capacitor Inductance: (H) Electrolytic Cap: Capacitance Value ( F)/working voltage (V), NP -~ non-polar (or bipolar) electrolytic cap. Refer to the parts list for additional component information. 2 indicates test point connection oh indicates chassis ground unless otherwise specifiec Hz _ indicates cycles per second For satety purposes (and continuing reliability) Aa replace all components marked with safety syrnbo! with identical type. NOE: FR — fusible resistor ——e23-

Parts identification on circuit boards: e.g. SU1126A (R107 = R1107) SU3030A (R113 = R3113)

Page 72

REPLACEMENT PARTS LIST - ELECTROHOME 19”’ MONITOR Outside of the P.C.B. Ass'y Symbol

Components identified by the A symbol in the PARTS LIST and on the Schematic have special characteristics important to safety DO NOT degrade the safety of the set through improper servicing.

Abbreviations for Resistors and Capacitors

Resistor

CR Comp. R OM R VR MF R CMF R UNF R FR Capacitor

Carbon Resistor C Cap. Composition Resistor M Cap Oxide Metal Film Resistor E Cap. Variable Resistor BP E Cap. Metal Film Resistor Coating Metal Film Resistor MM Cap. Nonflammable Resistor PP Cap. Fusible Resistor MPP Cap. PS Cap Tan. Cap. Ceramic Capacitor Mylar Capacitor Electrolytic Capacitor Bi-Polar (or Non-Polar) Electrolytic Capacitor Metalized Mylar Capacitor Polypropylene Capacitor Metalized PP Capacitor Polystyrol Capacitor Tantal Capacitor

NOTE: When ordering replacement parts please specify the part number as shown in this list including part name, and model number. Complete information will help expedite the order. Use of substitute replacement parts which do not have the same safety characteristics as specified, may create shock, fire or other hazards. For maximum reliability and performance, all parts should be replaced by those having identical specifications.

SERVICE REPLACEMENT PARTS LIST

Symbol Description Main P.C.B. Ass'y CRT Socket P.C.B. Ass'y Purity Shield Ass'y Part Number SU-1133A SU-3032A 07-220083-03 Description Picture Tube 19” AXDeflection Yoke PC Magnet A\Flyback Transf. AHVR UNF Resistor 2209,25W K C Capacitor 150pF, AC1.5KV Si. Transistor Si. Transistor Screw #8-% Screw % x % Pix Tube Mtg. (4) Pyramidal Lock Washer (4) Nut Retainer, Pix Tube Mtg. (4) Clip — P.C.B. Support Standoff Wire Terminal (Gnd. Strap) Terminal Lug (Gnd.) Groundstrap Assy. Grounding Spring Wire Hook (Gnd. Strap) Purity Shield Holddown Clamp Support Brkt. RH Support Brkt. LH Chassis Base Yoke Wedge (3)

Purity Shield Ass’y. Parts List

Symbol

0911, 0912

c911 R921 Description Degaussing Coil Rectifier 1 Amp 600V (2) Pin Terminal (2) Pin Terminal Housing Purity Shield (2 pes.) Purity Shield (2 pcs.) Capacitor 100nF 10% 400V Resistor, Wirewound 332, 4W Fire Retardent Term. Strip 4 Lug

CRT Socket P.C.B. Ass’y (SU-3032A) Parts List

Resistors Symbol R3105 R3106 R3113 R3114 R3115 R3116 R3117 R3118 R3119 R3120 C3121

Capacitors ‘Symbol C3107 C3108

Coils Symbol 13101 Description Vv R 200 Vv R 200 v R 5K Vv R 5K Vv R SK OM R 10KQ2W J OM R 10KQ2W J OM R 10KQ2W J Comp. R 3.3KQ%W K Comp. R 3.3KQ2%W K Comp. R 3.3KQ2%W K

Description E Cap. 10uF 250V A C Cap. 1000pF DC1400V P

Description Peaking Coil Part Number 17-7198-03 A29779-D = 21-141-01 A75034-B = 29-32-01 A29951-B A46600-A QRF258K-221 QCZ0101-005 2SD870 2SC1106A 31-610818-06 31-601418-12 33-255-01 33-494-01 33-629-02 33-670-010R-02 334-228-903 34-33-04 34-574-02 35-212-03 35-3053-02 35-2348-01 35-3890-01 35-3890-02 38-449-02 39-1233-01

Part Number 21-1007-30 28-22-27 34-708-01 34-709-01 35-3847-01 35-3847-02 48-171544-62 42-113301-03 34-492-09

Part. Number QVZ3234-022 QVZ3234-022 QVZ3234-053 QVZ3234-053 QVZ3234-053 QRG029J-103 QRG029J-103 QRG029J-103 QRZ0039-332 QRZ0039-332 QRZ0039-332

Part Number QEWS53EA-106 QCZ9001-102M

Part Number QQL043K-101

Page 73

Semiconductors , Symbol X3101 X3102 X3103

Miscellaneous Symbol A Description Si. Transistor Si. Transistor Si. Transistor

Description ASCRT Socket

Main PCB Ass'y (SU-1133A) Parts List

Resistors Symbol R1406 R1408 R1410 R414 R1415 R1421 R1422 AFR1401 » 4R1503 R1504 R1509 R1512 R1514 Q1515 R1522 R1523 R1528 R1534 VR1501 AR1703 A\R1704 4R1901 R1902 R1903 R1904 R1905 AQ1908 AR1909 R1910 AFR1901

Capacitors Symbol C1301 1402 C1407 C1411 C1412 C1508 Ac1512 AC1513 AC1514 C1515, ©1520 C1523 1524 4c1531 C1532 C1904 C1905 Description v R 2002 v R 2002 CMF R 6.8Q1WJ OM R 33KQIWJ OM R 2.7K OAW J OM R 12K22W J v R 10K2 AF R 6822W K ACMF RR 11,.BKQ UW +1% v R 5KQ. OM R 10KQ2W J OM R B.2K22W J OM R g2022W J CMF R B2Q1WJ CMF R 4.7Q1WJ OM R 6822W J OM R 390Q1W J ZN R ZN R ACMF R 30Q%W +1% ACME Ro 7.68KQ.%W +1% AsPosistor UNF R 22Q7WK CMF R 4.723WJ OM R 10KQ22W J OM R 18KQiW J ACMF RR 472”W +1% v R 2kQ ACMF B 2.74KQUWW +1% AF R 2202%W K

Description BPE Cap. 3.3uF 50V A Tan. Cap. 2.2uF 16V K E Cap. 4.7uF 6.3VA E Cap. 100uF 160V A Ee Cap. 3.3uF 160V A PP Cap. 5600uUF 50V J APP Cap. 2000pF DC1500V J AXPP Cap. 2000pF OC1500Vv J A\PP Cap. 2000pF DC1500V J PP Cap. 0.53uF DC1200V J BPE Cap. 3.3uF 50V A

  • Cap. 1uF 160V A M_— Cap. 0.1uF 200V k ZsPP_— Cap. 2000pF DC1500V J AXPP Cap. 1500pF DC1500V J E Cap. E Cap. 10uF 250V A Part Number 2SC1514VC 28C1514VC 28C1514VC.

Part Number A76068

Part Number QVZ3230-002 QVZ3230-002 QRX019J-6R8 QRG019J-332 QRGO0195-272 QRG026J-1232 QVZ3230-014 QRHO024K-680M QRV142F-1182 QVZ3230-053 QRG026J-103Z QRG026J-8222 QRG026J-821Z QRX019J-8R2 QRX019J-4R7 QRG026J-680Z QRGO019J-391 ERZ-C05ZK471 ERZ-CO0SDK271 QRV 122F-3902 QRV142F-7681 A75414 QRFO76K-2R0 QRX039J-4R7 QRG026J-103Z QRGO19J-183 QRV122F-470Z QVP5A0B-023E QRV142F-2741 QRH124K-221M

Part Number QEN61HA-335Z QEES1CK-225B QEW51JA-475 QEWS2CA-107 QEWS52CA-335 QFP31HJ-562 QFZ0082-202 QFZ0082-202 QFZ0082-202 QFZ0067-534 QEN61HA-335Z, QEW62CA-105Z QFM720K-104M QFZ0082-202 QFZ0082-152 QEY0034-001 QEW52EA-106

Page 74

Coils Symbol 1802 1503 L1504

Transtormers Symbol 71501 T1503

Semiconductors Symbol (C1501

X1104 X1102 X1103 X1104 X1105 X1106 X1301 1302 X1303 X1304 X1305 X1401 X1402 X1501 X1901 Xx1902

D1101 D1102 D1103 01301 D1401 D1402

01503 D1504 01505 01506 D1507 D1508 Axp1701 4\D1901 A\D1902 401903 A\D1904 A\D1905

Miscellaneous Symbol ASF 1901 AXF1902 Description Linarity Coil Widih Coil Heater Choke

Description Hor. Drive Transf. Side Pin Transf.

Description ic

i. Transistor i. Transistor i. Transistor Transistor |. Transistor i. Transistor i. Transistor i. Transistor i. Transistor i. Transistor i. Transistor i. Transistor . Transistor . Transistor i. Transistor Si. Transistor

Si. Diode Si. Diode Si. Diode Si. Diode Si. Diode Zener Diode

Si. Diode Si. Diode Zener Diode Si. Diode Si. Diode Si. Diode AvZener Diode ASI. Diode vax

ASi. Diode AdZener Diode

Description AvFuse 1.254 ASUL Fuse 3A Part Number A39835 C30380-A, C20445-A

Part Number A46022-BM. €39050-A

Part Number HA11244

2SC1685(R) 28A673(C) 25C1685(R) 2SA8673(C) 2SC1685(R) 2SA673(C) 2SC1685(R) 2SC.1685(R) 28A673(C) 2SC1685(R) 2SC1685(R) 2sD478 28D478 2SC2610BK 2SC2688 (K.L.M.) 2SC1890A (E.F.) Wo6A WO6A Wo6A 1SZ473H 18Z473H RD10F(C) HF-1 VO9E RD11E(B) WO6A 18881 18Z473H RD20EV2 1$1887A 181887A 1$1887A 1S1887A RD6.8EV3

Part Number QMF53U1-1R25S QMF66U1-3R0S

Page 75

Sto 90Hty 6 x3: 198 ond IOS VIDEO AMP 2£C2540 a 2501685 Rid XI04 ond X108 ViDEC AMP 2526730 MOrexi0S ROB ViseO SUTEST 28caeit or 28cis!

: SU-3016 A | | |eRT SockeT

\col POWER REGULATOR STases SU-1103A MAIN PCB ASSY

Yo) BEFLECTION YOKE

7 501 HORIVE or wouT 4701 XRAY PROTECTOR 23ciso7 KL, 2sc2a7Iv 250898 or sussosea 2SCA3AC or 25C\ 28Caeii or EScz6i0pK 250869

ACI20V 6OH:/SOH2 210%

G07-FBO

00-4147-03 Schematic Notes Unless otherwise specified Resistance: (2) (KKQ, MMQ,), 1/4 (W) carbon resistor Capacitance: 1 or higher (pF), less than 1-> (yF) working voltage 50 (V) ceramic capacitor Inductance: ( H) Electrolytic Cap: Capacitance Value (y F)/working voltage (V), NP — non-polar (or bipolar) electrolytic cap. Refer to the parts list for additional component information. Q indicates test point connection . ah indicates chassis ground unless otherwise specified Hz indicates cycles per second For safety purposes (and continuing reliability) PAN replace all components marked with safety symbol with identicai type.

NOTE: FR - fusible resistor —ex-

Parts identification on circuit boards: e.g. SU1126A (R107 = R1107) SU3030A (R113 = R3113)

Page 76

REPLACEMENT PARTS LIST - ELECTROHOME 13” MONITOR

Components identified by the 4 symbol in the PARTS LIST and on the Schematic have special characteristics important to safety.

DO NOT degrade the safety of the set through improper servicing.

Abbreviations for Resistors and Capacitors

Resistor Capacitor

CR: Carbon ResistorC Cap.
Comp. R: Composition ResistorM Cap
OMR: Oxide Metal Film ResistorE Cap.
VR: Variable ResistorBP E Cap.

MFR : Metal Film Resistor

CMF R: Coating Metal Film ResistorMM Cap.
UNF R: Nonflammable ResistorPP Cap.
FR: Fusible ResistorMPP Cap.

PS Cap Tan. Cap. Ceramic Capacitor Myiar Capacitor Electrolytic Capacitor Bi-Polar (or Non-Polar) Electrolytic Capacitor Metalized Mylar Capacitor Polypropylene Capacitor Metalized PP Capacitor Polystyrol Capacitor Tantal Capacitor

NOTE: When ordering replacement parts please specify the part number as shown in this list including part name, and model number. Compiete information will help expedite the order.

Use of substitute replacement parts which do not have the same safety characteristics as specified, may create shock, fire or other hazards. For maximum reliability and performance, all parts shou! replaced by those having identica! specifications.

Symbol

Outside of the P.C.B. Ass’y Symbol Av01 AXDYO1

ARN ASRO5 ACO4 x01 Ico1 Lot

BR

sc WA

CH Description Main P.C.B. Ass'y CRT Socket P.C.B. Ass'y

Description AsPicture Tube A\Deflection Yoke PC Magnet Wedge A\Flyback Transf. AFocus V R UNF Resistor 2202, 25W. K AC Capacitor 150 pF, AC1.5KV Si. Transistor IC Regulator Degausing Coil Degausing Coil Pin Terminal (2) Degausing Coil Pin Terminal Housing Groundstrap Ass'y. Groundstrap Wire Terminal Groundstrap Spring (2) Support Bracket RH Support Bracket LH SCREW 10-% Pix Tube Mtg. (4) Pyramidal Lockwasher (4) Clip P.C.B. Support (2) Ground Lug Chassis Base dbe

Part Number

SU-1103A SU-3016A

Part Number

370ESB22(E) C29123-V A76366-A 30006 A19183-A A46606-A QRF258K-221 QCZ0101-005 2SD869 STR383 21-1007-31 34-708-01 34-709-01 34-697-04 34-228-03 35-3560-01 35-3919-01 35-3919-02 31-631018-08 33-255-01 33-629-02 34-33-04 38-452-01 Main P.C.B. Ass'y (SU-1103A) Parts List

Resistors Symbo! R1406 R1408 R1410 Riatg R1415 R1421 R1420 AXFR1401 A\R1503 R1504 R1509 R1511 R15%4 R15i5 R1522 R1523 R1528 R1534 VR1501 A\R1703 ASR1704 AxR1901 R1902 R1903 R1904 AXFR1901

Capacitors Symbol 1402 C1411 C1412 1508 C1511 AC1512 AC1513 AC1514 C1515 C1520 1824 C1904 C1905 Axc1907

Coils Symbol L1501 L1502 L1503 L1504 L1901

Transformers Symbol 71501 T1503 Description voeoR v R CMF R OM Fi OM R OM R vVooR AF R ACMF R vVoR OM R OM R OM R CMF R CMF R OM R OM R ZN R ZN R ACMF R A\CMF R AsPosistor 2002 2002 6.82Q1W J 3.3KQ 1W J 2.7KQ1W J 12KQ2W J 10KQ. 6822W K 11.BKQYUW +1% 5KQ. 1OKQ2W J 5.6KQ2W J 6802.2W J 8.201W J 4.7Q1W J 56.22W J 3902 1W J

39K QUW +1% 7.68KQYW +1%

UNF R 2Q7WK CMF R 5.623W J OM R 10KQ2W J AF = R 2202%4WK

Description Tan. Cap. E Cap. E Cap. PP Cap. E Cap. AXPP Cap. A\pP Cap. A\PP Cap. PP Cap. BPE Cap. M_= Cap. 2.2uF 16V K 100uF 160V A 3.3uF 160V A 5600pF SOV J 47uF 160V A 2000pF DC1500V J 2000pF DC1500V J 2500pF DC1500V J 0.53uF DC1200V K 1uF SOV A 0.1uF 200V K E Cap. E Cap. XMM Cap. 10uF 250V A O.1uF AC150V Z

Description Peaking Coil Liniarty Coil Width Coil Heater Choke Line Filter

Description Hor. Drive Transf. Side Pin Transf.

8-20 Part Number QVZ3230-022 QVZ3230-022 QRX019J-6R8 QRG019J-332 QRG019J-272 QRG029J-123 QVZ3224-014H QRHO024K-680M QRV142F-1182 QVZ3230-053 QRG029J-103 QRG029J-562 QRG029J-681 QRX019N-8R2 QRX019J-4R7 ORG029J-560 ORG019J-391 ERZ-C05ZK471 ERZ-CO5DK271 QRV122F-3902 QRV142F-7681 A75414 QRFO76K-2RO QRX039J-5R6 QRG026J-103Z QRH124K-221M

Part Number

QEES1CK-225B QEWS2CA-107 QEW52CA-335 QFP31HJ-562 QEW52CA-476S QFZ0082-202 QFZ0082-202 QFZ0082-252 QFZ0067-534 QEN61HA-105Z QFM72DK-682M QEY0034-001 QEWS52EA-106 QFZ9008-104

Part Number A75360-6 A39934 C30380-A C30333-A A39475-J

Part Number A46022-BM C39050-A

Page 77

Semiconductors Symbol 101501

x1401 X1102 1103 X1104 X1105 X1106 x1301 1302 1303 X1304 X1305 x1401 x1402 X1501 x1701 01101 D1102 D1103 D1301 01401 01402 D1503 01504 11505 01506 01507 1508 4xD1701 AD1901 A\D1902 4xD1903 4\D1904

Miscellaneous Symboi AMF 1901 AF 1902 Description Le.

Si. Si. Si. Si. Si. Si. Si. Si. Si. Si. Si.

Si. Si. Si. Si. Si. Si. Si. Si. Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Diode Diode Diode Diode Diode Zener Diode Si Si. |. Diode . Diode Zener Diode Si. Si. Si. |. Diode . Diode . Diode AdZener Diode ASi ASi ASi ASi . Diode . Diode . Diode |. Diode

Description AsFuse 1A AMUL Fuse 3A

8-21 Part Number HA11244

2SC1685(R) 2SA673(C) 2301685(R) 28A673(C) 28C1685(R) 2SA673(C) 2SC1685(R) 28C1685(R} 2SA673(C) 2SC1685(R) 2$C1685(R) 2SD478 2sp478 2SC2610BK 28C1685(P-S) wo6A WO6A WO6A 1$2473H 182473H RD10F(C) HF-1 VoOaeE RD11E(B) WO6A 18881 182473H RD20EV2 1S1887A 181887A 1818874 181887A

Part Number QMF53U1-1ROS QMF66U1-3R0S

Page 78

CRT Socket P.C.B. Ass'y (SU-3016A) Parts List

Resistors Symbol 3105 R3106 R3113 R314 R3115, 3116 R317 R3118 R3119 R3120 R321

Capacitors Symbol C3107 C3108

Collis Symboi 13101

Semiconductors Symbol X3101 X3102 X3103

Miscellaneous Symbol a& Description VR 2008: v R 2060 VOOR 5K: VR SK2 v R 5K OM A 10KQ2WJ OM R 10K22W J OM R 10KN2W J Comp. R 3.3K2%W K Comp. R 3.3KQ%W K Comp. R 3.3KR2%W K

Descripiion E Cap. 10uF 250V A C Cap. 1000pF DC1400V P

Description Peaking coil

Description Si. Transistor Si. Transistor Si. Transistor

Description ASCRT Socket

8-22 Part Number QVZ3234-022 QVZ3234-022 QV2Z3234-053 QVZ3234-053 VZ3234-053 QRGG29J-103 QRGO29J-103 QRG029J-103 QRZ00Z9-332 QRZ0039-332 QRZ0039-332

Part Number QEWS52EA-106 QCZS601-102M

Part Number QQL043K-101

Part Number 2802611 2SC2611 2802611

Part Number A75522

Page 79

IX Schematics and Wiring Diagrams |

Page 80

CONN 3 15 POS POWER CHASSIS

CONN 4 | © FOS

Yee SND ores To wowitem

YEULM ENO Sta ts CoN B28 EUW ENE STARE 16 COMTHOL a Lome cons: SUPER PAG MAN MOSI- OBIS - A003

j Belt, | mioway 10691 W BEL FRANKLIN CREDIT BYPASS BD, 1682 91848 = CO.

Sw neTURN ve

Page 81

DESIGNATION LIST

DESIGNATION

ci-c9 clo Cu, ci2 C13 -C18 CPI-CP48 RI-R3 R4

RS

Re

RT

Re

RO

R10

RI RI3 Ria

RI5-RI7

RIB-R2i

R23-R46

R50,R51 R52

R53, R54 R55-R58 RML, RM2 Ic 1A,IF “138 “1c “1D “TE, IK, 1d,1K “PL, IM,IN

"2a "28 “2c “2D “ 26,2H,2u,2K OF

1c 4a "48 "ac “40 A 4e 4F 4H “40 "ak 4L “ 4M,4N FI-FB4 ICS 2C,20,2F “ 26,2H,2u,2K,3¢ "30,3F,30 "3L 4C,4E "4D PI Jt

PCMH) ~PCMH4 8080 -91435 -D3I6 DESCRIPTION _ 4 MF AX. TANT. 470 MF AX. ELEC. 470 PF oo" CER. (oO PF" o" IMF AX. CER. | Kk ORM 1/4 W 5% CRBN a70" mH

Ik" = %

a7o "he 220 " "#8

470" NH

220"*"oe'

1 | Fema “ I: cw +

IK«4ee-
1000"Hoo
pek"«wowenaere&

ET OR Ee MR a

22K"4woe
look"*wowE
82nooncrau
loooO"wonaeaa

22k Ik 9 Pos si Ma ine BOR yeRN oe oe sepia on 74832 : 3 "Og

" "138~=Se

“OS 273 _ ‘ “8 34s [ rt

B ig

161 car Gigg ME

741804

wo3684

07 Xx CUSTOM IC -

OOxx*“

N58725P 04 Xx CUSTOM 748161 74 LS 10 “0 Bg PROM SPV-! 11 Xx CUSTOM IC ; Fb if fl [ ( [

( \

Ic

omonae ive OuAuJSau sane WW 09 Dam Ayman saIVa e881 o 91e9 seri6-raoy NeW-Ovg Waanis 08 Dd oun news

PROM SPV-2 74 LS 273 12 XX CUSTOM IC 74LS 378 BP-ROM SPV-3 (SPI-4) 74 LS 365 74.8 74 BP ROM SPV-4 (SPI-6) PAL SPV-5 (SPI-7) BP-ROM SPV-6(SPI-5) 748 377 741886 “8 20 "187 "" 298 2148 STATIC RAM _FERRITE BEAD 28 PIN IC SOCKET 24Pin " :

2erPin""©REVISIONS

feuwn [useo on SUPER PAC-MAN

le rinMED ONSUPER PAC-MAN(Bally | MIDWAY MFG.CO.

20PIN" FRANKLIN PR iLL ‘50 PIN CON

IL PIN conn KneieeASSEMBLY DW6PART NO.
RT ANGLE,SUPER PACMAN VIDEO PC.MO5!1- 00316- D006

SCRW A084- 91435- D316 SUPER PAC-MAN VIDEO PC. CROSS REFERENCE LIST

0508 - 00800-0500 0550-00800-02c9

0508 - 00800: 0300 0935-00814 - C100 0550 - 00890~ 1300

0062 -10483- Xxx 0062 - 11085 -1Xxx 0062 -1S3B3-1xXxx

0062-179B3-i¥

0062- 195B83-1x

0506 -00804-020

0066 -001CX-KAPX 0066-003¢X-XAP 0066 -O08CX-xKA 0066-O18Cx- XAP 0066 -QI9CX- xAPX

0300 - 00803-0027 0300- 00803-0028 9300- 00803-0030 0300- 00803-0051 0300-00803 - 0052 0300 - 00803 -003) 0300-00803 -0032

0300-00803-0054 0300 - QO80z - 0033 0300 -00803 - 0050 0300 - 09803 -0044

0300- 00803-0046 0300-00803. 0038 0316 -00803 -0019 0318 - 00803-0020 0300-00803 - 0004 0316 - 00803 - 0021 0316 - 00803 - COIs 0316 - 00803-0017 0316 ~ 00803-0014

0316 ~ 00803~- COIS 0316 - 00803 ~ 0013 0316 - 00803 - 00'5 0316 - 00803 ~ C012

2500 9550- 00803-6200

0316 - 00804-9000

0508-00804-0700 0850-00804- 23500 0508 -00804-~ 0500 0508-00804-04C0

9300 00804-1104

3000-16387 ~1!

DESCRIPTIONQTYDESIGNATIONPART NO.
100 PF AX CER6cl3-cis
4a70Pe "2cil-c12
MF""48cPl-cp48
1) MF AX. TANT.&ci-co
470 MF AX. ELEC1C10
82 OHM I/4W 5% CRBN'R52
100““-.5R 14,R50, R51,R53,R54
220"a3R5,R8, R10
470"=i"3R4,R7,R90062-15683
t«"a“oe10RI-R3, RG, RIN-RIS,

RI5-RI7

22k "“ome32RI8- R21, R23-R46

R55-R58

1k 9 POS SIP2RMI, RM2
O0Xx CUSTOM IC1Ic 20
O4XxX"‘!"OF
o7xx"!"2c
xx"H"3D
laxx"a1"Bu
7418001Ic 48
74 L8041"2A
74 LS 081"1B
74S 10'"3A
74S 201"ag
7418 322”OTAVIF
74.8741"an
7418862“ 3B,4H
7418 1381"—1¢
74LS 187fi"aK
74Lsi6i6“IL,IM, IN, 2b,

2M, 2N

74 LS 2454“1B,1H, 101K
74182732"10,3H
74Ls 2981"aL
74 LS 3652” 3M,3N
741s 368'“28
74L8 3771"oF
74 LS 378i"3k
BP-ROM SPV-6 (SPI-5)1Ic 4€
PROM SPV-!4“3¢
BP- ROM SPV-3 (SPi-4)'Ie 3
PROM SPV-21“SF
BP-ROM SPV-4 (SPI-6)'"ac
PAL SPV-5 (SPI~7)'"4D
N58725 P4IC 2€,2H,2U,2K9508 ~ 00803
2148 STATIC RAM2"4M, 4n
FERRITE BEAD4FBI-FB4
\6 PIN IC SOCKET3CS 3L, 40,4
20 PIN ""'"4D
24 PIN ".5"2€,2H,2u,2K,3¢
28 PIN “=6"2C,20,2F,

3D, 3F 3d

50 PIN CONN1PI
WUPIN"KK-156iJt

RT ANGLE

SCRW4PCMHI = PCMH4

SUPFR PAC-MAN vinen OF 0316 - 00700 ~ 00xF

Page 82

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 83

DESIGNATION LIST

DESCRIPTION DESIGNATION DESCRIPTION IGNATION RIPTION

BE DESCRIPTION. CROSS REFERENCE LIST

9-4 ae gee os P= eer re Rose siasec rae Most; Ope” 5 F008

Page 84

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 85

DESIGNATION LIST ‘n082-00427-A000 ares: CROSS REFERENCE LIS’

—egCeewe as "Sesesoycs
Opt RO TANTIN 4001—““a7 0tnlcur0845-00811-0100DESCRIPTIONOTY DESIG. NOS.(PART NOS.
srogt axe,Been+seersae:aenatesosoan
eho rarydE: fon. Be +eee'isser2 ves0948-00818 - 0100
guafrenonw6016 onm sw ox.'nics905-00815-0100
8 = aw + crewTagua¥+,ee eeeimeFUSE cute w/stoestr
aooleaveswinéonewa:ves.et.08—onts-conoa-osoo | TaesPw apt 10.rcMon oost.noee
urae.ruse Vea.siome[2gseoreswear siNK Ass¥=0017-00088-0139

[ramet Me J. JARON. Justo ou BLUEPRINT Baty | MIDWAY MFG.CO. a a ‘ASSY ORWNG.MED PS.70 VA poe aeea = Kom 9-6 Vater 427-4000

Page 86

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 87

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 88

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 89

PROJ. ENG.: J. SZERSZEN THIS DWG. IS CONFIDENTIAL & PROPERTY OF MIDWAY MFG. CO.

DIM. TOLERANCES UNLESS OTHERWISE SPEC. By MID WA Y MFG. Co. CONCENTRICITY T.1.R. . 602 FRANKLIN PK., IL. 60131 A BALLY CO.

FRACTIONAL . REVISIONS SCHEMATIC DRAWING, CREDIT MULTI. [panTwo —— 7 #00 BYPASS P. C. BOARD 05-1 -0°0°9°3-2 -A-0-2°8

DO NOT SCALE DWG. A082-91109-A000

BRUNING: 40-107 o ' = fo) NATION LIST DESIGNATION DESCRIPTION Jt 7 PIN CONN. KK-I56 W/PIN 3 REMOVED DSCRR QTY DESIG. PART NOS. 7 PINCONN. \ Jl 0932-0081 7-04.00

KK1S6 W/ PIN3 REMOVED

PCHMI,PCMH2 /e' HEYCO NUT 8"HEYCO 2 PCMHI, 0017-00042-0014 NUT PCMH2 PC BD i —— A080-91!109-A000}

PCMHI

PROJ.ENG=J.SZERSZEN DIM. TOLERANCES PAC-MAN UNLESS OTHERWISE SPEC. rT Pos/ieke 56 FULL THIS DWG. IS CONFIDENTIAL & PROPERTY OF MIDWAY MFG. CO. MIDWAY MFG. CO. FRANKLIN PK.,IL.60131 A BALLY CO ASSEMBLY DWG PART NO. CREDIT MULT. BYPASS PC BDIy.9-5-1 -0-0-9-3:2 -A-0-2-7 A082-91109-A000 : :

CONCENTAICITY T.1.R. . 002 FRACTIONAL ...... +.1/64 DECIMAL .......... +.005 HOLE DIA. .... +.002—.000 ANGLE ............ £1/2° 00 NOT SCALE DWG. REVISIONS

Page 90

Chip Number

74LS04 74LS08 74LS32 74LS74 74109 74LS138 74LS157 74LS158

74LS161 74LS245 74LS257 74LS259 74LS273 74LS367 74LS368 MC68A09

Chip Number

74LS00 74LS04 74LS08 74LS10 74LS20 74LS32 74L874 74LS86 74LS138 74LS157 74LS161 7ALS245 74LS273 74LS298 74L S385 T4LS368 SUPER PAC-MAN CPU BOARD (P.C. A084-91436-C316)

Function

Hex Inverters Quad 2 Input AND Quad 2 Input OR Dual D Type Flip-Fiop Dual JK Type Flip-Flop 3 to 8 Line Decoder/Multiplexer Quad 2 to 1 Line Multiplexer Quad 2 to 1 Line Multiplexer — Inverted Outputs 4 Bit Binary Counter Octal Bus Transceivers Quad 2 to 1 Line Multiplexer — Tri State 8 Bit Addressable Latches Octal D Type Flip-Flop Hex Bus Drivers Hex Bus Drivers — Inverting CPU Chip

Number Function

2764 8K x 8 EPROM 2732 4K x 8 EPROM AM9114 1K x 4 RAM MBM2148 1K x4 RAM 2114 1K x 4 RAM SP1-1 PAL SP1-2 PAL SP1-3 256 x 4 PROM M7052 18.4320 Crystal MC14066 Quad Bilateral Switches M83730 Audio Amplifier O7XX Custom Horizontal & Vertical Syne Generator — A5XX Custom Address Generator 16XX Custom Bus Controller 56XX Custom I/O Ports

SUPER PAC-MAN VIDEO BOARD (P.C. A084-91435-C316)

Function

Quad 2 Input NAND Hex Inverters Quad 2 Input AND Triple 3 Input NAND Dual 4 Input NAND Quad 2 Input OR Dual D Type Flip-Flop Quad 2 Input XOR 3 to 8 Line Decoder/Multiplexer Quad 2 to 1 Line Multiplexer 4 Bit Binary Counter Octal Bus Transceivers Octal D Type Flip-Flop Quad 2 Input Multiplexer (With Storage) Hex Bus Drivers Hex Bus Drivers — Inverted Outputs Chip

74LS377 Octal D Type Flip-Flop 74LS378 Hex D Type Flip-Flop 2764 8K x 8 EPROM 2732 4K x 8 EPROM 2148 1K x 4 RAM M58725 2K x 8 RAM OOXx Custom Address Generator 04xx Custom Address Buffer O7XX Custom Horizontal & Vertical Syne Generators 11XX Custom Bit Shifter 12XX Custom Address Generator SP1-7 PAL 3160-15AXL-CXPD 256 x 4 PROM 3160-15AXL-BXPD 256 x 4 PROM 3160-03AAC-AXPD 32 x 8 PROM