Pole Position II CO-218-12 1st Printing
Pole Position II (Japan) (Namco, 1983) · Change Order · 72 pages · 54 sections · original scan
CO-218-12 ‘Ast Printing
*Pole Position and Pole Position Il are engineered and designed by Namco Ltd., manufactured under license by Atari, Inc. © 1982, 1983. Trademark and © 1982, 1983.
If reading through this manual does not lead to solving a certain maintenance problem, call TELEHELP® at the Atari Customer Service office in your geographical area, as shown below.
WEST and CENTRAL U.S.A. Parts and Service
Atari, Inc. California Customer Service Office 737 Sycamore PO. Box 906 Milpitas, CA 95035 Telex 17-1103 (Monday-Friday, 7:30-4:00 pm Pacific Time) = From California, Alaska, or Hawaii (408) 943-1120 POW Service from anywhere in the area shown in white toll-free (800) 538-1611
EAST U.S.A. Service Only
Atari, Inc. New Jersey Customer Service Office 12A World's Fair Drive, Somerset, NJ. 08873 Telex 37-9347 (Monday-Friday, 7:30-4:00 p.m. Eastern time) s From New Jersey (201) 469-5993 Ss From anywhere else in this area toll-free (800) 526-3849
Europe Parts and Service
Atari Ireland Limited European Customer Service Office Tipperary Town, Ireland Telex 28165 (Monday-Friday, 9:00-6:00 pm GMT) TIRPERARY TOWN) IRELAND @ 062-52155
Operators Manual
*Pole Position and Pole Position || are engineered and designed by Namco Ltd., manufactured under license by Atari, Inc. © 1982, 1983. Trademark and © 1982, 1983.
Safety Summary
The following safety precautions apply to all game operators and service personnel. Specific warnings and cautions will be found throughout this manual where they apply.
A WARNINGS A
Properly Ground the Game. Players may receive an electrical shock if this game is not properly grounded! To avoid electrical shock, do not plug in the game until it has been inspected and properly grounded. This game should only be plugged into a grounded 3-wire outlet. If you have only a 2-wire outlet, we recommend you hire a licensed electrician to install a grounded outlet. Players may receive an electrical shock if the control panel is not properly grounded! After servicing any parts on the panel, check that the grounding clip is firmly secured to the metal tab on the inside of the control panel. Only then should you lock up the game. AC Power Connection. Before connecting the game to the AC power source, verify that the proper voltage-selection plug is installed on the game's power supply. Disconnect Power During Repairs. To avoid electrical shock, disconnect the game from the AC power source before removing or repairing any part of the game. When removing or repairing the video display, extra precautions must be taken to avoid electical shock because high voltages may exist within the display circuitry and cathode-ray tube (CRT) even after power has been disconnected. Do not touch internal parts of the display with your hands or metal objects! Always discharge the high voltage from the CRT before servicing this area of the game. To discharge the CRT: Attach one end of a large, well-insulated, 20-kV jumper to ground. Momentarily touch the free end of the grounded jumper to the anode by sliding it under the anode cap. Wait two minutes and discharge the anode again. Use Only ATARI Parts. To maintain the safety integrity of your ATARI game, do not use non- ATARI parts when repairing the game. Use of non-ATARI parts or other modifications to the game circuitry may adversely affect the safety of your game, and injure you or your players. Handle Fluorescent Tube and CRT With Care. If you drop a fluorescent tube or CRT and it breaks, it may implode! Shattered glass can fly six feet or more from the implosion. Use the Proper Fuses. To avoid electrical shock, use replacement fuses which are specified inthe parts list for this game. Replacement fuses must match those replaced in fuse type, voltage rating, and current rating. In addition, the fuse cover must be in place during game operation.
Properly Attach All Connectors. Make sure that the connectors on each printed-circuit board (PCB) are properly plugged in. Note that they are keyed to fit only one way. If they do not slip on easily, do not force them. A reversed connector may damage your game and void the warranty.
© 1983 by Atari, Inc. All rights reserved. No part of this publication may be reproduced by any mechanical, photographic, or electronic process, or in the form of a phonographic recording, nor may it be stored in a retrieval system, transmitted, or otherwise copied for public or private use, without permission from the publisher. The game play, all graphic designs, this technical manual, its accompanying schematic diagrams, and the display manual are protected by the U.S. Copyright Act of 1976. This Act provides for increased penalties for violating federal copyright laws. Courts can impound infringing articles while legal action is pending. If infringers are convicted, courts can order destruction of the infringing articles. In addition, the Act provides for payment of statutory damages of up to $250,000 in certain cases. Infringers may also have to pay costs and attorneys’ fees and face an imprisonment of up to five years. Atari will aggressively enforce its copyrights against any infringers. We will use all legal means to immediately halt any manufacture, distribution, or operation of a copy of video games made by us. Anyone who purchases such copies risks forfeiting such a game.
Published by: ATARI, INC. 790 Sycamore Drive PO. Box 906 Milpitas, California 95035
Printedinthe USA. 11M
Notice Regarding Non-ATARI Parts
You may void the game warranty (printed on the inside back cover of this manual) if you do any of the following:
- Substitute non-ATARI parts in the game. © Modify or alter any circuits in the game by using kits or parts not supplied by Atari.
NOTE
This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual, may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of Federal Communications Commission (FCC) Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area or modification to this equipmentis likely to cause interference in which case the user, at his own expense, will be required to take whatever measures may be required to correct the interference. If you suspect interference from an ATARI® game at your location, check the following: ¢ All green ground wires in the game are properly connected as shown in the game wiring diagram. © The power cord is properly plugged into a grounded three-wire outlet. © The game printed-circuit boards (PCB) are properly installed within the Electromagnetic Interference (EMI) cage. © The EMI Shield PCBis properly installed and connected in series with the game PCB harness. © All filter capacitors required on the EMI Shield PCB are properly soldered in place. Ifyou are still unable to solve the interference problem, please contact ATARI Customer Service. See the inside front cover of this manual for service in your area.
Table of Contents
oe -Up New Features .. 0.6.0... cece eens a Inspecting the Game : C. Switch Locations .....
- Power On/Off Switch . .
- Utility Panel Switches
- Option Switches . Option Switch Settings. Game Play.......
- Attract Mode : :
- PlayMode ......... 0... cece ccc eee eee eee eens
- High-Score Mode ... 1.0.6... cece eee
- Hints for Game Play . B. SCOPING... eee Self-Test A. Comments on Troubleshooting . : : B. SelfTest Procedure ........... 0.0.2 ee eee Parts Lists Cabinet-Mounted Assemblies—Upright............... 00. c cece eae Cabinet-Mounted Assemblies—Sit-Down ................-0.00020005 Fluorescent Tube and Speaker... .. 2.2.00... ccc cece eee ee Printed-Circuit Board Hardware Central Processing Unit PCB Assembly—Atari . Central Processing Unit PCB Assembly—Namco . Video PCB Assembly—Atari.............. : Video PCB Assembly—Namco .......... 20.006 c eee eee eee eee mo
4 Schematic Package Changes.......................... OAARAAA BeEUSERE . 112 1-12
List of Illustrations
Figure 1-1 Game Overview—Upright Cabinet ......................00. 1-2 Figure 1-2 Game Overview—Sit-down Cabinet . wee 13 Figure 1-3 Switch Locations .. 0.0... eee eee eee 1-5
Figure 2-1 Self Test Screen 1: Upright Test Passes . 2-3 Figure 2-2 Self Test Screen 1: Si 2-3 Figure 2-3. Self Test Screen 1: Test Fails........... 2-4 Figure 2-4 Self-Test Screen—Explanation of Prompts seve 26 Figure 2-5 Self Test Screen 2; Crosshatch .... 2.0.0.0... cece cece eee 2-6
Figure 3-1 Cabinet-Mounted Assemblies, Upright Cabinet ............... 3-2 Figure 3-2 Cabinet-Mounted Assemblies, Sit-Down Cabinet -. 35 Figure 3-3 Fluorescent Tube and Speaker Board Assembly . .. 39 Figure 3-4 Printed-Circuit Board Hardware ................00 0.0 eee eee 3-10
List of Tables
Table 1-1 Pole Position and Pole Position II Part Number Comparison... . . . 1-6 Table 1-2 Switch Settings for Play Options ................. . 17 Table 1-3 Switch Settings for Price and Special Play Options . 18 Table 1-4 Qualifying Lap Times and Bonus Points ........ . 19 Table 1-5 Switch Settings for Racing Lap Times..................0..2. 1-10
Table 2-1 Component Locations on the Atari VideoPCB ................ 2-2 Table 2-2 Component Locations on the Atari CPU PCB .. . 22 Table 2-3 Component Locations on the Namco Video PCB . 2-2 Table 2-4 Component Locations on the Namco CPU PCB .. . 23 Table 2-5 ROM Locations (Atariand Namco) ........ . 24 Table 2-6 RAM Locations (Atari) ......... . 24 Table 2-7 RAM Locations (Namco) .......... 2.002000 eee cece eee eee 2-5
Table 4-1 SP-218 Schematic Package Changes ...................0005 4-2 Table 4-2 SP-219 Schematic Package Changes .....................055 42
1 Set-Up Procedures
Introduction
Pole Position II, the sensational sequel to Pole Position, offers you a choice of 4 racetracks! These tracks—FUJI, TEST, SUZUKA, and SEASIDE—are based on actual international raceways. This document is a supplement to TM-218 (Pole Position Operation, Maintenance, and Service Manual) because the Pole Position Il cabinets are very similar to the Pole Position cabinets. Part numbers that are different between the two games are listed in Table 1-1. Information about game play, option-switch settings, selftest procedures, printed-circuit boards (PCB), and part numbers for Pole Position I! is contained in this document. We also describe how to change the Pole Position Schematic Package (SP-218 or SP-219) to support Pole Position I. If you need more information, refer to TM-218.
Set Up CO-218-12
Attraction Glass & Film ® See Figure 3-3
- Game Identification Label
+ Video Display ® See Figure 3-4 seco EMI Cage See Figure 3-4 Dashboard |
Steering Whee! Assembly See Figures 3-3 or 3-4 yon Moet
jure 3-5 in I"¢ 3 oF 3 ‘9 : = in TM-218 g i TM2I6:
+Game PCBs See Figures 3-4
A through 3-8
\ee J Gear-Shifter Utility Panel \ SN See Figure 3-8 in TM-218 See Figure 3-15 in TM-218 Capacitor ml «Regulator/Audio See Figure 3-24 in TM-218 PCBs See Figures 3-21 or 3-22 in TM-218. Control Panel See Figures 3-3 & 3-4 in TM-218
Speaker See Figure 3-12
1 * Power Supply Power On/Off Switch Coin Door ‘See Figure 3-24 in TM-218 See Figures 3-16 or 3-17 in TM-218
Foot-Pedal Assy. See Figures 3-9 or 3-10 in TM-218
Connect this game ONLY to a x Items with a serial number label on U.S.-Built cabinets grounded 3-wire outlet. If you havea. 2-wire outlet, we recommend you hire a licensed electrician to installa grounded outlet. You may receive an electrical shock if the game is not properly grounded!
Figure 1-1 Game Overview—Upright Pole Position Il
1-2
C0-218-12 SetUp
+ Game Identification Label Items with a serial number label
Fan Assembly Utility Panel +Game PCBs See Figure 3-2 See Figure 3.45 in TM-218 See Figures 3-4 through 3-8 in TM-218 EMI Cage
See Figure 3-4 Speaker
See Figures 3-2 or 3-13 in TM-218
x Game ID label on access door.
Access Door
+Regulator/Audio ll PCBS See Figures 3-21 of 3-22 in TM-218
Power On/Off Switch See Figure 3-24 in TM-218 Capacitor See Figure 3-24 Video Display in TM-218 See Figure 3-14 inTM 218
Steering-Wheel Assembly See Figure 3-5 in TM-218
Gear-Shifter See Figure 3-8 in TM-218
Control Panel See Figure 3-4 in TM-218
See Figures 3-16 or 3-17 in TM-218
Accelerator and Brake Assy. See Figures 3-9 or 3-10 in TM-218 Connect this game ONLY to a grounded 3-wire outlet. If you havea. 2-wire outlet, we recommend you
hirea licensed electrician to install a
grounded outlet. You may receive an electrical shock if the game is not properly grounded!
Figure 1-2 Game Overview—Sit-Down Pole Position II
1-3
Setup
A. New Features
Pole Position I has several new features:
- Pole Position II presents a choice of 4 racetracks— FUJI, TEST, SUZUKA, and SEASIDE. Each track offers the player a unique challenge and different racing times. Faster game play—the times listed in Table 1-5 in this document are faster than the times listed in Table 1-6 in TM-218. The time displayed on the screen is not in real seconds but “game” seconds. © The option-switch settings for Pole Position II are different than the Pole Position settings. For complete listings of the option-switch settings, refer to Tables 1-2 through 1-6.
Connect this game ONLY to a grounded 3wire outlet. If you have a 2-wire outlet, we recommend you hire a licensed electrician to install a grounded outlet. You may receive an electrical shock if the game is not properly grounded!
1-4 CO-218-12
B. Inspecting the Game
Inspect your game carefully to ensure that it was delivered to you in good condition. Game inspection and setup procedures are listed in TM-218, Sections B, C, and D.
Do not plug in the game until the procedures in Sections B, C, and D in TM-218 have been completed.
After you have completed these procedures, connect this game ONLY to a grounded 3-wire outlet. If you have a 2-wire outlet, we recommend you hire a licensed electrician to install a grounded outlet. You may receive an electrical shock if the game is not properly grounded.
C. Switch Locations
- Power On/Off Switch The on/off switch is behind the game on the lower left side (see Figure 1-3).
- Utility Panel Switches The volume control(s), self-test switch, coin counter(s), and auxiliary coin switch are located on the utility panel. The utility panel is located inside the upper coin door. The volume control adjusts the level of sound produced by the game. The Upright cabinet has two volume controls: one for each speaker. The Sit-Down cabinet has four volume controls: one for each speaker. The self-test switch is used to enter and exit the Self-Test diagnostic routine. The coin counter(s) records the number of coins entered intothe game. The auxiliary coin switch is used to credit the game without activating the coin counter(s). See Figure 3-15 in TM-218 for more information about the utility panel.
- Option Switches If your game has Atari PCBs, the option switches are at locations 9L and 9JA on the CPU PCB. If your game has Namco PCBs, tne option switches are ai iocations 7E and 9E on the CPU PCB (see Figure 1-3).
c0-218-42
Option Switch Locations
Namco CPU PCB
Utility Pane! a T See Figure 3-15 in TM-218
oe
POWER ON/OFF SWITCH SD sanery
Figure 1-3 Switch Locations
Set-Up CO.218-12
Table 1-1 Comparison of Pole Position and Pole Position II Part Numbers
Description of Item Type of Cabinet Pole Position Pole Position II Part Number Part Number
| Self-Test Chart | Upright and Sit-Down | S¥-218-01 | ST-255 |
| CPU PCB (Atari) | Upright and Sit-Down | A039185-21 | A039185-22 |
| Video PCB (Atari) | Upright and Sit-Down | A039187-21 | A039187-22 |
| CPU PCB (Namco) | Upright and Sit-Down | 171031-001 | 171031-001 |
| Video PCB (Namco) | Upright and Sit-Down | 171032-001 | 171032-001 |
| PCB Label (for CPU and Video PCB) | Upright and Sit-Down | Not Required | 041377-01 |
| Left Side Panel Decal | Upright | * | 041353-01 |
| Right Side Panel Decal | Upright | * | 041353-02 |
| Instrument Panel Decal | Upright | 7 | 041355-03 |
| Attraction Panel Film | Upright | 039485-03 | 041354-02 |
| Attraction Glass | Upright | 037410-01 | 037410-01 |
| Foam Tape (for attraction glass) | Upright | 78-6900404 | 78-6900404 |
| Video Display Shield with Graphics | Upright | 039417-01 | 041356-01 |
| Left Side Panel Decal—Rear | Sit-Down | * | 041378-01 |
| Right Side Panel Decal—Rear | Sit-Down | . | 041378-02 |
| Left Side Panel Decal—Front | own | : | 041379-01 |
| Right Side Panel Decal—Front | Sit-Down | . | 041379-02 |
| Left Control Panel Decal | Sit-Down | . | 041380-04 |
| Right Control Panel Decal | Sit-Down | 7 | 041380-05, |
| Front Panel Decal | Sit-Down | . | 041382-01 |
| Foam Tape (for display shield) | Sit-Down | 78-6900804 | 78-6900404 |
| Video Display Shield with Graphics | Sit-Down | 039148-01 | 041381-01 |
*Pole Position did not have decais because its panels were silkscreened.
D. Option-Switch Settings Tables 1-2 through 1-5 explain options and switch settings. Options preset at the factory are shown by the < symbols. But you may change the settings to suit your needs. Table 1-2 lists switch settings for options relating to racing difficulty levels (A is easiest; D is hardest). It also lists settings for laps per game, preliminary game time, and speed. Table 1-3 describes the switch settings for options relating to game pricing (coin mechanism" multipliers), unit of speed (MPH or KPH), attract mode sound, and freezing the screen. Table 1-4 provides qualifying lap times and bonus point information.
- Acoinmechanism is a device on the inside of the coin door thatinspects acoin to determine ifthe correct coin has been inserted. The mechanism either accepts or rejects the coin. The coin door has two coin mechanisms. The multipliers (JA switches 1-5) determine the value of the coin mechanisms to the game's logic. The basic unit of measurementisa coin worth $.25 or 1 DM, which equals a multiplier of x1. For example, if you nave a2 DM/1 DM coindoor. vou may want to set the left muttiolier at x2 and the right multiplier at 1
1-6 Table 1-5 provides racing lap times tor extended laps.
To verify option-switch settings, set the self-test switch to the on position. Compare the information on the screen (see Figure 2-1 for an explanation of messages on the screen) to the option-switch settings listed in the tables in this section. If these settings are the ones you want, set the self-test switch to the off position. If you want to change settings, set the self-test switch to off, set the power on/off switch to off, and change the switch settings.
Pole Position Ii leaves the factory with option switches set at the manufacturer’s recommended difficulty level. The game will be exciting and challenging for players at these settings.
CO-218-12
Table 1-2 Switch Settings for Play Options
Settings of 8-Toggle Switch on Pole Position II PCB (location 9L or 9E) 1 2 3 4 5 6 7 8 Option
Off On
On Off
Off Off
Off On
On On
On Off
On On
On Off Off On Off On On
Off On Preliminary Game Time 90 seconds * 120 seconds <4
Preliminary Rank A Bax Cc D
Extended Rank A Bak Cc D
Number of Laps
4s 5<
Speed Average speed High Speed <4
“4 Manutacturer’s recommended settings for Sit. Down
+ Manufacturers recommended settings for Upright
SetUp C0-218-12
Table 1-3 Switch Settings for Price and Special Play Options
Settings of 8-Toggle Switch on Pole Position II PCB (location 9JA or 7E)
| 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8° |
Option
Off Off Of
On Off Off
Off On Off
| On | On | Oft |
Ott Off On
On Off On
Off On On
| On | On | On |
Ott Off On Off Off On On On
Off On
Off On
Off On Left Coin Mechanism 1 coin for 1 credit * 1 coin for 2 credits 1 coin for 3credits 2 coins for 1 credit <4
3 coins for 1 credit 3 coins for 2 credits 4 coins for 3 credits Free Play
Right Coin Mechanism 1 coin for 1 credit * 2 coins for 1 credit 3 coins for 2 credits 1 coin for 6 credits
Unit of Speed Kilometers per hour Miles per hour <¢
Attract Mode Sound Sound <4 & Silence
Screen Freeze Normal Action << Freeze
“¢ Manufacturer's recommended settings for Sit Down
- Do notturn switch 8 on! +* Manufacturer's recommended settings for Upright
Tabie 1-4 Qualifying Lap Times and Bonus Points
Seconds to Quality
Suzuka Track
Ba c
Seaside Track
Ba c
Fuji Track Test Track
A Ba c D A B~< c D
Position Bonus
56 55 545 54 54 53 525 52 54 535 57 565 58 57 565 56 56 55 545 54 56 55.5 59 585 2 2000
60 59 585 58 58 57 565 56 575 61 605 3 1400 62 61 605 60 60 59 585 58 60 595 63 625 4 1000
64 63 625 62 62 61 605 60 62 615 65 645 5 800 66 65 645 64 64 63 625 62 64 635 67 665 6 600
68 7 665 66 66 655 7 400
69 685 675
“4Manufacturer's recommended settings. CO-218-12 Set-Up
Set-Up CO-218-12
Table 1-5 Switch Settings for Racing Lap Times
Track Number Extended Number of Game Seconds For Each Extended Lap ofLaps’ Rank Race Lap? Lap1 Lap2 Lap3 Lap4 Lap5
3 A 80 43 57 3 Ba 7 46 56 3 Cc 75 44 55 3 D 7 42 54
4 A 80 46 57 57 4 Ba 75 56 56 4 Cc 75 47 55. 55 FuJl 4 D 7 45 54 54
5 A 80 46 58 58 58 5 B= 75 49 57 57 7 5 Cc 75 47 56 56 56 5 D 7 45 55 55 55
6 A 80 46 58 58 58 60 6 Ba 75 49 57 57 57 59 6 Cc 7 47 56 56 56 58 6 D 75 45 55 55 55 57
3 A 80 39 55 3 Ba 7 42 54 3 c 7 40 53 3 D 7 38 52
4 A 80 42 54 54 4 Ba 7 43 53 53 4 Cc 75 43 53 53 TEST 4 D 75 4 52 52 5 A 80 42 56 56 56 5 Ba 7 45 55 55 55 5 Cc 75 43 54 54 54 5 D 75 4 53 53 53 6 A 80 42 56 56 56 58 6 B< 75 44 55 55 55 57 6 Cc 75 43 54 54 54 56 6 D 75 4 53 53 53 55
3 A 80 43 57 3 Ba 75 46 56 3 c 75 44 55 3 D 75 42 54 4 A 80 46 57 57 4 B< 75 49 56 56 4 Cc 75 47 55 55 SUZUKA 4 D 75 45 54 54 5 A 80 46 58 58 58 5 Ba 75 49 57 57 57 5 Cc 75 47 56 56 56 5 D 75 45 55 55 55 6 A 80 46 58 58 58 60 6 Ba 7 49 57 57 57 59 6 Cc 75 47 56 56 56 58 6 D 75 45 55 55 55 57
*Number of laps is identified in Self-Test as “GOAL”. 2If your racing lap time is less than the time listed. the remaining seconds are added to the next lap. 4 Manufacturer's recommended settings.
1-10
CO-218-12 Set-Up
Table 1-5 Switch Settings for Racing Lap Times, continued
Track Number Extended Number of Game Seconds For Each Extended Lap
| of Laps’ | Rank | Race Lap? | Lap1 | Lap2 | Lap3 | Lap4 | Lap5 |
| 3 | Ba | 75 | 48 | 57 | |||
| 3 | Cc | 7 | 46 | 56 | |||
| 3 | o | 75 | 44 | 55 | |||
| 4 | A | 80 | 48 | 58 | 58 | ||
| 4 | Ba | 75 | 51 | 57 | 57 | ||
| 4 | Cc | 7 | 49 | 56 | 56 | ||
| SEASIDE | 4 | io} | 7 | 47 | 55 | 55 | |
| 5 | A | 80 | 48 | 59 | 59 | 59 | |
| 5 | Ba | 75 | 51 | 58 | 58 | 58 | |
| 5 | Cc | 7 | 49 | 87 | 57 | 57 | |
| 5 | Oo | 7 | 47 | 56 | 56 | 56 | |
| 6 | A | 80 | 48 | 59 | 59 | 59 | 61 |
| 6 | Ba | 75 | 51 | 58 | 58 | 58 | 60 |
| 6 | Cc | 75 | 49 | 57 | 57 | 57 | 59 |
| 6 | Oo | 75 | 47 | 56 | 56 | 56 | 58 |
‘Number of laps is identified in Self-Test as “GOAL”. 2If your racing lap time is less than the time listed, the remaining seconds are added to the next lap. 4 Manufacturer's recommended settings.
E. Game Play
Pole Position Il is a one-player game using a color rasterscan video display. Game action takes place at 4 different taceways—the Fuji Speedway in Japan, the Test Track (an oval track like Indy), the Seaside Speedway (with the Long Beach Pike in the background), and the Suzuka Speedway in Japan. The unique and picturesque scenery around each raceway adds exciting realism to each race! The driver drives a Formula-1 race car on each track. Player controls consist of a steering wheel, atwo-position gear shifter, an accelerator, and a brake pedal (on the Sit- Down cabinet). The first objective of the game is to finish the qualifying lap as quickly as possible. If the driver beats the times specified in Table 1-4, he qualifies for the race. If he does not qualify, he drives the remainder of his time along the qualifying course. As a qualifier, the driver is ranked according to his qualifying lap time, from position one (the pole position) to position eight. Then the driver’s second objective is to race against the clock and other cars to finish the race laps (operator selects the number of laps) as fast as possible, and to achieve the highest score possible. The driver earns points for passing cars, driving on the track, and finishing the race with time remaining. The time remaining from the Racing Lap is added to the extended lap time listed in Table 1-5. Pole Position II has four modes of operation: Attract, Play, High-Score, and Self-Test. Self-Test is a special mode for checking the game controls, switches, and computer functions. You may enter the Self-Test Mode from any other mode. However, all credits will be cancelled. See Chapter 2 for complete Self-Test information.
- Attract Mode
The Attract Mode begins when the power on/off switch is set to on or after the Play, High-Score, or Self-Test Modes. The Attract Mode ends when the correct amount of credit for a game is inserted or when the Self-Test Mode begins. The Attract Mode begins with the words ‘‘Pole Position” and “Ii” tumbling toward you until they stop. Then, the Attract Mode simulates game play (one track atatime). Eight cars are at the starting line. The driver’s car, located in the eighth position, flashes on the screen. The starting lights flash from red to green and the race starts. The race continues until the driver's car crashes into another car and explodes into a red ball of fire. The message GAME OVER appears in the center of the screen. Finally, the Attract Mode displays the High-Score Table. Each track has its own high-score table, and this section of the Attract Mode will display a map of the track, the name of the track, the fastest lap time of the track, and the top speed reached at that track. It will also list information about the top six scores reached at that track—the position number, the score, the time, and initials of the driver. Pole Pesition Il appears on the screen, and at the bottom of the screen is the copyright message.
Set-Up
- Play Mode To start the Play Mode, a driver must first enter the correct number of coin(s) for a game. Then the driver turns the steering wheel until the track he wants to drive on is highlighted in white. The Play Mode will begin when the driver steps on the accelerator. The driver's car will appear behind the starting line and 90 (or 120) seconds will be on the clock (see Table 1-2 for settings for Preliminary Game Time seconds). The car must finish the qualifying lap within the time listed in Table 1-4 to be in the race. If the driver does not qualify, his car continues on the track until 120 seconds elapse. Ifthe driver has qualified, just before the race begins, the driver's car (flashing on the screen) is placed at the starting line with seven other cars. The position of the car depends onthe position earned during the qualifying lap. The starting lights flash from red to green, and the race begins. Racing hazards are other racing cars, sharp turns, puddles, and road signs. As the race progresses, more cars appear on the track. If the driver’s car hits another car or aroad sign, the driver's car is destroyed in an explosion. The driver's car reappears in a few seconds and the race continues. Driving through wet puddles or off the track slows down the driver's car considerably. Experience will teach a driver which turns on which tracks require slight steering (because they're banked) and which turns require fast and forceful steering. He jockeys for position with the other racers, while keeping his eye on the clock at the top of the screen. When his time runs out, the race is over. If he has beaten the racing lap time listed in Table 1-5 and has seconds remaining, the remaining seconds are added to his next lap. The top score achieved by a driver appears at the top of the screen. The time allotted for the lap is displayed under the top score. Increasing lap time (in seconds and hundredths of a second) and the speed of the car appears last. CO-218-12
- High-Score Mode The High-Score Mode begins when the driver has earned one of the 100 highest scores. The screen will show his tanking from 1 to 100. If his score is in the top 20 scores for the track, he’ll have one minute to record his initials (each track has its own high-score table). The driver rotates the steering wheel to change initials, and presses the accelerator to select the initial. The third press will enter the initials into the high-score table.
- Hints for Game Play
- Avoid puddles and the sides of the track because these slow the driver down. e Accelerate before the green light appears, and stay ahead of other racers.
- — Drive the inside of the track to make the corners. ¢ Donot oversteer (tracks are banked). ¢ Engine soundwill cue the driver when to shift to high gear.
- When sliding, steer into the skid.
- Scoring Points are scored for completing laps and passing cars. 10,000 points are awarded for completing alap. Points are also scored for every foot of track driven. 200 points are awarded for each second remaining on racing laps. At the end of agame, 50 points are scored for each car the driver passes.
2 Self-Test
SelfTest
A. Comments on
Troubleshooting
When troubleshooting, first determine the symptom(s) of the failure. After determining the symptom, look over the wiring diagram and determine what assemblies could cause the failure. Could it be caused by the power supply, Regulator/Audio II printed-circuit board (PCB), or the video display? The next step is to check all harness wires and connectors to the suspected assembly. If you do not find a harness or connector problem, substitute an assembly known to be good for the suspected failing assembly. If the game functions properly, you have successfully isolated the failure. If it doesn’t, repeat the procedure with another assembly. When you have isolated the failing assembly, you must troubleshoot that assembly and make the necessary repairs. If the video display fails, we suggest that a qualified video-display technician handle the troubleshooting and repair. Be sure to refer to The Book—A Guide to Electronic Game Operation and Servicing, published by Atari, Inc., whenever you need help with the techniques, tools, and terminology associated with coin-operated electronic games. To effectively troubleshoot a game PCB, learn as much as you can about the PCB. The diagramsin the Schematic Package (SP-218 for Atari PCBs; SP-219 for Namco
Table 2-1 Component Locations on the Atari Video PCB
Symptom Area PROM Custom RAM
Ic
Large Car Pictures 12J, 13d Large Sign Pictures 12K, 13K, 12L, 13L Smail Cars & Signs 12N, 13N
| All Cars & Signs | 12H, 11N | 13H | 9F, 10F |
| Alphanumerics | 7N, 8M | 8N | |
| Raceway | 2L, 2M, | 3N |
2N, 4L Background 6N, 5K Raceway & Background SL, 6L Middle & Sides of 2B, 2C, Raceway 2D All Video 4D, 7E, 2F
Red NE
Grean nD Blue nc CO-218-12
Table 2-2 Component Locations on the Atari CPU PCB
Symptom Area PROM Custom RAM _ A-to-D Converter
Audio Voice 9c 9D Screech/Crash 9E Player’s Motor 12E, 12F AllOtherSounds = 7L, 11D TK, 7 Inputs Brake and/or Accelerator 8d Steering 9K Option Switches 9K, 9M All Other Inputs 9M
Control—Audio & 8H, 9H Inputs
Syne 7M
High Scores 7E
Table 2-3 Component Locations on the Namco Video PCB
Large Car Pictures 5M, 5N
Large Sign Pictures 3M, 4M, 3N, 4N
Small Cars & Signs 1M, 1N
| All Cars & Signs | 1L, 6M | 6N | 7, 7K |
| Alphanumerics | 1F, 2H | 1H | |
| Raceway | 1A, 2A, | 1B |
3A, 3C
Background 4D, 1E Raceway & Background 3D, 3E
Middle & Sides of 9A, 10A,
Raceway NA
All Video 7A, 9C, 8F Red 8L Green 9L Blue 10L
2-2
CO-218-12
PCBs) show the functions of the circuitry. To troubleshoot aPCB, first determine the symptom of the failure, then locate the suspected area on the schematic diagram. Tables 2-1 and 2-2.will help you locate faulty components on the Atari PCBs, and Tables 2-3 and 2-4 will help you locate faulty components on the Namco PCBs.
Table 2-4 Component Locations on the Namco CPU PCB
Symptom Area PROM Custom RAM A-to-D Ic Converter
Audio Voice 2E 3D Screech/Crash 4E Player's Motor 5A, 6A AllOther Sounds = 3B, 9H 7H, 8H
Inputs Brake and/or Accelerator 7F Steering 8D Option Switches 8D, 10D All Other Inputs 10D
Control—Audio & Inputs 6E, 6F
Sync 10H
High Scores 4H
B. Performing the Self-Test
This game will test itself and provide data to show if the game's circuitry and controls are operating properly. This data is provided on the video display and speakers. No additional equipment is necessary. We suggest you perform the self-test procedure when you first set up the game, when you collect money from the game, when you change game options, or when you suspect game failure.
Self-Test Procedure The self-test switch is located on the utility panel inside the coin door. The option switches are on the CPU printed-circuit board (see Figure 1-3). Selffest
Without touching the pedal(s), turn the self-test switch on. The self-test program will test the game memory (RAM and ROM). All credits will be cancelled. Test Passes: Random symbols are displayed on the screen for about 5 seconds as RAM and ROM are tested. If the memories are good, the screen will look like Figure 2-1 or 2-2.
RAM OK Rom OK
| ACCEL 00 | BRAKE | OO | |
| STEERING | 00 | SHIFT | LO |
SOUND ° COIN1 1COIN i1CREDIT COIN2 1COIN iCREDIT TIME 90
Figure 2-1 Self-Test Screen 1— Upright Test Passes
ACCEL 00
BOM OK
BRAKE 00
| STEERING | OO | SHIFT | Lo |
° 2COINS ICREDIT 2COING ACREDIT
Figure 2-2 Self-Test Screen 1— Sit-Down Test Passes
SelfTest c0-218-12
Test Fails: If the Pole Position !I Custom integra- Table 2-6 RAM Locations (Atari) ted circuit (IC) has failed, the screen will continue to display random symbols and colors, and the message ERROR IC25 will be in the upper left PcB Screen Display RAM Location
| corner. Whenever a ROM fails, its name will ap- | Vid | RAMO | 8F |
pear on the screen (e.g., ROM 1 failedin Figure Video RAM 1 TF
| 2-3). Use Table 2-5 to locate the ROM that the | Video | RAM 2. | 8H |
| screen indicates is bad. A failed RAM will also | Video | RAM3. | 7H |
appear on the screen. Use Table 2-6 or 2-7 to lo-
cate the RAM that the screen indicates is bad. Video RAM 4 3F
Action: Replace the failed RAM or ROM. Start Video RAMS se
| the self-test again (turn the self-test switch off, | CPU | RAM6 | w |
| then on.) | CPU | RAM 7 | 7K |
| = | CPU | RAM8 | 7E |
| Video | RAM 20 | 8F | |
| Video | RAM 21 | 7F |
Video RAM 22 BU
| Video | RAM 23 | vA) | ||
| Video | RAM 24 | 8H | ||
| Video | RAM 25 | 7H | ||
| Video | RAM 26 | 8K | ||
| Video | RAM 27 | 7K | ||
| Video | RAM 28 | 3F | ||
| Video | RAM 29 | 4F | ||
| Video | RAM 30 | 3E | ||
| Video | RAM 31 | 4E | ||
| Video | RAM 40 | 8F | ||
| Video | RAM 41 | 7F | ||
| Figure 2-3 | Self-Test Screen 1— | Video | RAM 42 | 8J |
| Test Fails | Video | RAM 43 | w | |
| . | Video | RAM 44, | 8H | |
| Table 2-5 | ROM Locations | Video | RAM 45 | 7H |
(Atari and Namco) Video RAM 46 8K
| Video | RAM 47 | 7K |
Location on Location on i
| Video | RAM 48 | 3F | |||
| Screen Message | AtariCPUPCB | Namco CPU PCB | Video | RAM 49 | 4 |
| Video | RAM 50 | 3E | |||
| ROMO | 7H | “ | Video | RAM 51 | 4E |
| ROM 1 | 7F | 5H | |||
| ROM 2 | 3L | 8M |
- Now, start testing the controls and switches. Press
| ROM 3 | 4. | 8 | the accelerator pedal. |
| ROM 4" | 3K | 7™ | Test Passes: The numbers to the right of ACCEL |
increase from 00 to A0 as you press down on the
| ERROR IC25 | 4K | 7L | pedal. |
| ROM6 | 3E | 4M | Test Fails: The numbers to the right of ACCEL do |
not change, or no numbers appear.
| ROM7 | 4E | 4L | Action: Suspect a bad A-D converter on the CPU |
PCB ora mechanical problem on the foot pedal
| ROM8 | 30 | 3M | assembly. Troubleshoot using the information in |
| ROMS | 4D | 3L | TM-218 (Chapter 3, Section B) and the game |
schematics.
“Not used
2-4
CO-218-12
Table 2-7 RAM Locations (Namco)
PCB Screen Display | RAM Location .
Video RAM O 7H
| Video | RAM 1 | 7F |
| Video | RAM 2 | 6H |
| Video | RAM3 | 6F |
| Video | RAM 4 | 7B |
| Video | RAM5. | 8B |
| cPu | RAM6 | 7H |
| CPU | RAM 7 | 8H |
| CPU | RAM 8& | 4H |
| Video | RAM 20 | 7H |
| Video | RAM 21 | 7F |
| Video | RAM 22 | 5H |
| Video | RAM 23 | 5F |
| Video | RAM 24 | 6H |
| Video | RAM 25 | 6F |
| Video | RAM 26 | 4H |
| Video | RAM 27 | 4F |
| Video | RAM 28 | 7B |
| Video | RAM 29 | 7c |
| Video | RAM 30 | 8B |
| Video | RAM 31 | 8C |
| Video | RAM 40 | 7H |
| Video | RAM 41 | 7F |
| Video | RAM 42 | 5H |
Video RAM 43 SF
| Video | RAM 44 | 6H |
| Video | RAM 45 | 6F |
| Video | RAM 46 | 4H |
| Video | RAM 47 | 4F |
| Video | RAM 48 | 7B |
| Video | RAM 49 | 7c |
| Video | RAM 50 | 8B |
| Video | RAM 51 | 8c |
- Press the brake pedal of the Sit-Down cabinet. Test Passes: The numbers to the right of BRAKE increase from 00 to FF. For the Upright cabinet, the numbers to the right of BRAKE should always read 90. Test Fails: The numbers to the right of BRAKE do not change as you press the brake pedal. On the Upright cabinet, brake failure is indicated by anything other than 00 appearing to the right of BRAKE. Action: Ifthe test fails, suspect a bad switch, improper mechanical adjustment of the foot pedal assembly, or no ground of the brake edge-connector pin in the harness. Troubleshoot using the information in TM-218 (Chapter 3, Section B) and the game schematics. SelfTest
- Turn the steering wheel clockwise, then counterclockwise. Test Passes: The numbers to the rightof STEER- ING increase as the wheel turns clockwise and decrease as the wheel turns counterclockwise. Test Fails: The numbers to the right of STEER- ING do not change properly as you turn the wheel. Action: li the test fails, suspect the Coupler PCB. Troubleshoot using the information in TM-218 (Chapter 3, Section B) and the game schematics.
- Shift the gear shifter. Test Passes: The words to the right of SH/FT change from LO (shifter up) to H/ (shifter down) as you shift gears. Test Fails: Failure is indicated if the words to the right of SH/FT do not change from LO to H/ as you shift gears. Action: Suspect loose connector wires or a bad switch. Troubleshoot using the information in TM-218 (Chapter 3, Section B) and the game schematics.
- To test the sounds of the game, shift the gear shift, press the auxiliary coin switch on the utility panel, and activate the coin switches. Test Passes: The numbers to the right of SOUND increase from 00 to 20, and a different sound is played with each number. Test all 20 sounds. Test Fails: Failure is indicated by silence when the coin switches or gear shifter are activated. Action: Make sure the volume control is turned up, or check for a loose harness or connector wire. The custom audio I/O chip or the Regulator/Audio I! PCB may be bad. Troubleshoot using the game schematics.
- Toverify that the option switches are set the way you need them, and to check game statistics, press the auxiliary coin switch. The screen will display Figure 2-4. Test Passes: Game statistics appear at the bottom of the screen. To erase game statistics, simultaneously press the accelerator pedal and press the auxiliary coin switch twice. Statistics will be reset at 999. To reset the high-score table, simultaneously press down on the accelerator pedal and shift the gear-shifter from low to high. The high-score table will be reset to contain fictitious scores. Test Fails: Option switches are not set the way you want them. Action: Turn the game power off. Set the option switches (see Tables 1-2 through 1-5 for possible
SelfTest CO-218-12
RAM is Good ROM is Good
Accelerator Pedal noe ox Brake Pedal Secon! BRAKE OO Gear Shifter SHIFT HI —~— Sounds. Left Coin Mechani: 1COIN ACREDIT - at GolniMechaniet
1COIN. ACREDIT - i, a . Qualifying Lap Time 2 Right Coin Mechanism
No. of Laps in the Race Race Difficulty Level See Table 1-5
Qualifying Lap Difficulty Level See Table 1-4 Manual Start (Select a track and press the accelerator to start the game) Game Statistics (Can be shown in hexadecimal or decimal)
No. ofGamesPlayed —No. of Points Scored(x 10) No. of Seconds Played Not Used The count starts at 999 and decreases. For example, if you play 10 games, the game subtracts 10 from 99.9, and the display shows 98.9 for the number of games played (disregard decimal points). 7 Fe No. of Seconds that the Game Has Had Power No. of Games in Which Player Reached the Finish No.;of Games.in Which No. of Games That Reached \ Line Player Has Qualified Second Extended Lap
No. of Games That Reached No. of Games That Reached First Extended Lap Third Extended Lap
Figure 2-4 Self-Test Screen— Explanation of Prompts
options). Turn the power on. Turn the self-test +} ttt switch off, then on. Verify the switch settings.
- Tosee self-test screen two, set the self-test switch to off and immediately back to on. Test Passes: A white crosshatch pattern appears on the screen (see Figure 2-5). Use this pattern for convergence adjustment (see the raster-scan video display manual). Test Fails: There is no failure for this test.
- Toend the test, turn the self-test switch off.
Figure 2-5 Self-Test Screen 2
3 Parts Lists
Parkas co.218-12
Manuals, Schematics, & Self-Test Label— ‘See parts list on next page
Fluorescent Tube and 041354-02 Speaker (Attraction Panel Film) See Figuie3-3 -003053-01 (Retainer) 037332-01 | (Ventilation grille) 78-6900402 (Tape)
78-6900402 (Tape) 03937101 Shield retainer) » _-A098881-01 (Lock) 041956-01- : EMI Ca: 039376-01 iN ge (Display shield wigraphics) : seotiones-4 es sal “S. 13903-1006, 04 2! oe eee (Video dispiay) 4040512-01 040565-01 (Fan harness assy.) (Exhaust duct) A040547-02 (Fan & bracket assy.) 114-0: 041355-03-@0, (Dashboard decal) ot 035438-01-@} (Bracket) (Dashboard housing) Game PCB Assy. Steering-Wheel Assy. See Figures 3-4
| See TM-218 | Gear-Shifter Assy. | E> | through 3-8 |
See TM:218 ( A039459-xx (Main harn. assy.) 179034024 | Control Panel Assy. (T-Molding) See TM-218 ; Us Regulator/Audio I!
| ‘ | 148001-013 | : | “ | PCB Assy. |
| Utility Panel | (Speaker) | : | Zs | and TM-218, |
| See TM-218 | =] | 03914401 | A |
(Speaker grille) 178048-001 (Caster)
Coin Door Assy. See TM-218 A039460-01 038870-01 (Power harn. assy, (Coin box enclosure— Power Suppiy not shown) See TM-218 037243-01 Lsehelca 038091-01 3. (Power cord) (Coin box—not shown) & (Base plate) A039353-xx 178034-025 (Cabinet assy.) A037470-01 (T-Molding) (On/off switch assy.) ~ 009982 78-3201 Foot-Pedal Assy. 941353-01 a (Glide) See 7™M-218 (Decal) (On/ott switch cover)
Figure 3-i Cabinei-iMounied Assembiies Pole Position I! Upright Cabinet A039352-01 T
3-2
CO-218-12 Parts Lists
Cabinet-Mounted Assemblies Pole Position tl Upright Cabinet Parts List
Part No, Description
| A037453-04 | Strain-Relief Power Cord | (U.S. and Canada) |
| A037701-01 | Electromagnetic Interference Cage | (includes glides) |
A038600-01 Power On/Off Switch/Mounting Plate Assembly A038881-01 Lock Assembly (for rear access panel) Acceptable substitute is part no. A038881-03
| A039353-01 | Cabinet Assembly | (includes glides and PCB retainers, but not the rear access panel) |
A039420-01 Dashboard Housing and Decal Assembly A039459-01 Main Harness Assembly A039460-01 Power Harness Assembly
| A039576-01 | Coin Option Interconnect Assembly | (not shown) |
A040512-01 Fan Harness Assembly
| 04054702 | Fan and Bracket Assembly | Acceptable substitute is part no. A040547-01 |
003053-01 Attraction Glass Retainer 009992-01 On/Off Switch Cover
| 035438-01 | ~~ | Dashboard Housing |
037243-01 Base Plate for Power Supply 037332-01 Ventilation Grille
| 038091-01 | Molded Coin Box | (not shown) |
038641-01 Speaker Grille (not shown)
| 038770-01 | Metal Coin Box Enclosure | (Acceptable substitute is part no. 038781-01) | (not shown) |
039144-01 Speaker Grille 039371-01 Video Display Shield Retainer
| 039376-01 | Rear Access Panel | (does not include lock) |
040546-01 Printed Circuit Board Mounting Bracket (not shown)
| 040564-01 | Door Panel Grille | (not shown) |
040565-01 Exhaust Duct
| 041353-01 | ns | Left Side Panel Decal |
| 041353-02 | sn | Right Side Panel Decal |
| 04135402 | os | Attraction Panel Film |
| 041355-03 | os | Dashboard Decal |
| 041356-01 | sn | Video Display Shield with Graphics |
| 139003-1006 | -@8 | 19-Inch Disco Color Raster-Scan Display |
148001-013 6- x 9-Inch Oval, 4-Ohm, 6-Ounce Shielded High-Fidelity Speaker (located on front pane/)
| 178114-032 | 2-Inch Plastic Tape | (20 inches required) |
The following nine items are technical information supplements to this game:
| CO-218-12 | ws | Pole Position i! Operators Manual |
| SP-218 | Pole Position Schematic Package | (for Atari PCBs) |
| SP-219 | Pole Position Schematic Package | (for NAMCO PCBs) |
| ST-255 | os | Pole Position Chart with Self-Test Procedure and Option Switch Settings |
SS New for Pole Position II.
(Continued on next page)
CO-218-12 Parts Lists
Cabinet-Mounted Assemblies Pole Position !! Upright Cabinet Parts List, continued
Part No. Description
TM-160 Service Manual for 19-Inch Electrohome Color Raster-Scan Display (use with part no. 92-049), or
| TM-210 | ~o | Service Manual for 19-Inch Disco Color Raster-Scan Display | (use with part no. 139003-1006), or |
TM-220 Service Manual for 19-Inch Matsushita Color Raster-Scan Display (use with part no. 139003-1004) TM-218 Pole Position Operation, Maintenance, and Service Manual
| TM-255 | oo | Enhancement Instructions |
78-3201 Adjustable Glide 78-6900402 Vinyl Foam Single-Coated Adhesive Tape, Ya-Inch Wide x %-Inch Thick (48 inches required—use on top edge of video display shield, and on top edge of control panel)
| 78-6900404 | -a | Vinyl Foam Single-Coated Adhesive Tape, %-Inch Wide x ¥4-Inch Thick | (48 inches required—used on |
top and bottom of attraction glass) 178034-024 34-Inch Black Plastic TMolding (located on side panels) 178034-025 2%2-Inch Black Plastic T-Molding (located on front panel) 178048-001 2-Inch Rigid Caster ‘-@ New for Pole Position II.
3-4
Co-2t812 Parts Lists
A040514-01 iti ae A039465-01 (Exhaust fan) (Main harness assy—US) 178093-001 A039245-02 A039101-01 (Main harness assy—Namco) (Cabinet assy.) (Fan blade guard) Game PCB Assy. See Figures 3-4 through 3-8 A037701-01 178034-034 (EMI cage) (FMolding)
. 148001-013 038641-01 s (Speaker) 148001-001 (Ventilation grille) = 039145-01 (Speaker) (Speaker grille) 039144-01 Grille)
‘A038881-01 . 178034-024 (Lock) g ; (F Molding)
038641-01 (Ventilation grille)
038091-01 (Coin box)
Utility Panel Regulator/Audio II PCB Assy. See TM-218 See TM-218
SY ‘Power Supply Assy. N See TM-218
A039246-01 A0s7470-01 (Power harness assy) (Oniott switch assy.) 009992-01 (On/ott switch cover) A037453-03 (Power cord)
Figure 3-2 Cabinet-Mounted Assemblies Pole Position I! Sit-Down Cabinet A039100-01 R
3-5
Parts Lists CO-218-12
Manuals, Schematics, & Self- Test Label— See parts list on next page Gear-Shifter Control Assy. See TM-218 On Bear jecal
Video Display See TM-218 037086-01 heel rol Assy. See ete sy. (Front window retainer)
78-6900804 (Tape)
039141-01 (Front window) 78-6900402 (Tape) FR ours90-04 YY (Decal [+X Control Panel Assy. See TM-218 041378-02 “ (Decal)
oatgar-01 A (Display shield wigraphics) 041380-05 <> (Decal) a 041379-01 (Decal)
Coin Door Assy. See TM-218 Foot-Pedal Assy. See TM-218 038870-01 (Coin box exclosure)
~ (041378-01 “Ss 041382-01 (Decal) (Decal)
178023-001 (Caster) be 78-3201 (Glide)
Figure 3-2 Cabinet-Mounted Assemblies, continued Pole Position I! Sit-Down Cabinet A039100-01 R
3-6
CO-21812 Parts Lists
Cabinet-Mounted Assemblies Pole Position II Sit-Down Cabinet Parts List
Part No. Description
| A037453-03, | Strain-Relief Power Cord | (U.S. and Canada) |
A037470-01 Power On/Ott Switch/Mounting Plate Assembly
| A037701-01 | Electromagnetic Interference (EMI) Cage | (includes guides) | |
| A038881-01 | Lock Assembly | (for rear access panel) | Acceptable substitute is part no. A038881-03 |
A039101-01 CabinetAssembly (includes glides and PCB retainers, but not the rear access panel)
| A039245-01 | Main Harness Assembly | (for NAMCO PCBs) |
A039246-01 Power Harness Assembly
| A039465-01 | Main Harness Assembly | (for Atari PCBs) |
A040514-01 Fan Harness Interconnect Assembly
| 107001-001 | Flat Black Paint | (not shown) |
171002-001 110 V Exhaust Fan 178093-001 Fan Blade Guard The following ten items are technical information supplements to this game:
| CO-218-12 | -— | Pole Position I Operators Manual |
SP-218 Pole Position Schematic Package (for Atari game PCBs) SP-219 Pole Position Schematic Package (for NAMCO game PCBs)
| ST-255, | oe ) | Pole Position l! Chart with Self-Test Procedure and Option Switch Settings |
TM-160 Service Manual for 19-Inch Electrohome Coior Raster-Scan Display (use with part no. 92-049) TM-201 Service Manual for 19-Inch Wells-Gardner Color Raster-Scan Display (use with part no. 92-055) TM-218 Pole Position Operation, Maintenance, and Service Manual TM-220 Service Manual for 19-Inch Matsushita Color Raster-Scan Display (use with part no. 139003-1004)
| TM-255 | a | Enhancement Instructions |
78-3201 Adjustable Glide 78-6900402 Vinyl Foam Single-Coated Adhesive Tape, /4-Inch Wide x %-Inch Thick (72 inches required; used on front window) 78-6900804 Vinyl Foam Single-Coated Adhesive Tape, ¥2-Inch Wide x ¥%-Inch Thick (50 inches required; used in top slot of video display cleat and bottom of display shield) 009992-01 On/Off Switch Cover
| 035851-01 | Top Panel Hinge | (not shown) |
037086-01 Front Window Retainer
| 037742-01 | Printed-Circuit Board Mounting Bracket | (not shown) |
038091-01 Molded Coin Box
| 038641-01 | Ventilation Grille | (on rear access panel) |
| 038870-01 | Metal Coin Box Enclosure | Acceptable substitute is part no, 038781-01 |
039141-01 Front Window
New to Pole Position Il.
(Continued on next page)
3-7
Parts Lists CO-218-12
Cabinet-Mounted Assemblies Pole Position Il Sit-Down Cabinet Parts List, continued
Part No, Description
039144-01 Speaker Grille (located behind seat) 039145-01 Speaker Grille (not shown—located under control panel)
| 041378-01 | - | Left Rear Side Panel Decal |
| 041378-02 | -3 | Right Rear side Panel Decal |
| 041379-01 | -e | Left Front Side Panel Decal |
| 041379-02 | -e | Right Front Side Panel Decal |
| 041380-04 | -3 | Left Control Panel Decal |
| 041380-05 | -e | Right Control Panel Decal |
| 041381-01 | -e | Video Display Shield with Graphics |
| 041382-01 | -3 | Front Panel Decal |
148001-001 6- x 9-Inch Oval, 4-Ohm, 15 W Unshielded High-Fidelity Speaker (located behind seat) 148001-013 6 x 9-Inch Oval, 4-Ohm, 15 W Shielded High-Fidelity Speaker (located under control panel) 178034-034 1-Inch Black Plastic TMolding (located on seat back) 178023-001 4Inch Rigid Caster
‘-@ New to Pole Position Il.
3-8
CO-218-12 Parts Lists
78-6900402 (Tape) 037410-01 (Attraction glass) &® 041354-02 003053-01 (Retainers) (Attraction glass film)
Fluorescent Tube & 039144-01 Speaker Assy. (Speaker-grille) See Figure 3-12 in TM-218
Figure 3-3 Fluorescent Tube and Speaker Board Parts List
Part No. Description
78-6900402 Vinyl Foam Single-Coated Adhesive Tape, ¥4-Inch Wide x %-Inch Thick 003053-01 Attraction Glass Retainer 037410-01 Attraction Glass 039144-01 Speaker Grille 041354-02 -s8 Attraction Glass Film
@ New to Pole Position Ii.
3-9
Parts Lists C0.218-12
‘A037767-01 (EMI ShieldPCB) 039378-03 (Retainer) 037873-01 176015-110 S , Shield PCB (Spacer) (Screw)
A039431-01 (End PCB)
f ae 034536-03 A037701-01 (Foam pad) 72-1604F (EM! cage) Screw)
a039185-22 “> “Ss ‘Gonna (Pole Position li CPU PCB) A039187.22 ) (Pole Position II Video PCB)
178045-442 (Fastener)
Figure 3-4 Printed-Circuit Board Hardware 72-1404F (Screw)
Parts List
Part No. Description
A037701-01 Electromagnetic Interference (EMI) Cage (includes guides) A037767-01 EMI Shield Printed-Circuit Board (PCB) A039185-22-e0 Pole Position Il Central Processing Unit PCB A039187-22-e8 Pole Position |! Video PCB 72-1404F #4-40 x Ys-Inch Cross-Recessed Steel Screw 72-1604F #6-32 x Ys-Inch Cross-Recessed Stee! Screw 034536-03 Foam Pad 037873-01 Spacer 039378-03 Dual-Slotted Retainer 175009-221 Plastic Spacer (for EMI Shield PCB) 176015-110 #10 x %-Inch Cross-Recessed Pan-Head Screw 178044-242 Grommet 178045-442 Snap-In Fastener
8 New to Pole Position Il.
3410
CO-218-12 Parts Lists
. Atari Pole Position II Central Processing Unit Printed-Circuit Board Assembly A039185-22 A Parts List
| Designator | Description | Part No, |
Capacitors
| C2-C5 | 0.01 nF, 100 V Radial-Lead Mylar Capacitor | 214101103 | |
| Cé | 33 pF, 100 V Radial-Lead Epoxy-Dipped Mica Capacitor | 128002-330 | |
| C7 | 0.1 uF, +10%, 50 V Ceramic-Disc Axial-Lead Capacitor | 122002-104 | |
| co | 10 uF, 25 V Aluminum Electrolytic Fixed Axial-Lead Capacitor | Acceptable substitute | 24-250106 |
is part no, 24-350106
| C10 | 0.1 uF, +10%, 50 V Ceramic-Disc Axial-Lead Capacitor | 122002-104 | |
| ci | 47 uF, 10 V Aluminum Electrolytic Fixed Axial-Lead Capacitor | Acceptable substitute is | 24- 100476 |
part no. 24-250476 or 24-160476
| ci2 | 0.1 nF, +10%, 50 V Ceramic-Disc Axial-Lead Capacitor | 122002104 | |
| C13 | 0.01 uF, +80%, -20%, 25 V Ceramic-Disc Axiai-Lead Capacitor | 122005-103 | |
| C14, C15 | 0.1 pF, +10%, 50 V Ceramic-Disc Axial-Lead Capacitor | 122002-104 | |
| C16-C23 | 0.01 uF, +80%, -20%, 25 V Ceramic-Disc Axial-Lead Capacitor | 122005-103 | |
| C24, C25 | 0.1 pF, +10%, 50 V Ceramic-Disc Axial-Lead Capacitor | 122002-104 | |
| C26 | 47 uF, 10 V Aluminum Electrolytic Fixed Axial-Lead Capacitor | Acceptable substituteis | 24- 100476 |
part no. 24-250476 or 24-160476
| C27, C28 | 0.0022 pF, +10%, 100 V Radial-Lead Plastic Film Capacitor | 121022-222 | |
| C29, C30 | 0.022 uF, 100 V Radial-Lead Mylar Capacitor | 21101223 | |
| C31, C32 | 0.01 pF, +80%, -20%, 25 V Ceramic-Disc Axial-Lead Capacitor | 122005-103 | |
| C33, C34 | 0.047 yF, 100 V Radial-Lead Mylar Capacitor | 21-101473 | |
| C35 | 0.022 »F, 100 V Radial-Lead Mylar Capacitor | 21-101223 | |
| C36 | 0.0047 uF, 100 V Radial-Lead Mylar Capacitor | 21-101472 | |
| C37 | 0.001 uF, 100 V Radial-Lead Mylar Capacitor | 21-101102 | |
| C38 | 0.0047 uF, 100 V Radial-Lead Mylar Capacitor | 21-101472 | |
| C39, C40 | 0.01 yF, 100 V Radial-Lead Mylar Capacitor | 21-101103 | |
| C41 | 47 uF, 10 V Aluminum Electrolytic Fixed Axial-Lead Capacitor | Acceptable substitute is | 24- 100476 |
part no. 24-250476 or 24-160476
| C42, C43, | 0.0047 »F, 100 V Radial-Lead Mylar Capacitor | 21101472 | |
| C44, C45 | 0.001 F, 100 V Radial-Lead Mylar Capacitor | 21-101102 | |
| C46 | 470 uF, 16 V Aluminum Electrolytic Fixed Axial-Lead Capacitor | Acceptable substitute | 24160477 |
is part no. 24-100477
| C47-C56 | 22 uF, 16 V Aluminum Electrolytic Fixed Axial-Lead Capacitor | Acceptable substitute is | 24-160226 |
part no. 24-250226 or 24-350266
| C57-C81 | 0.1 pF, +10%, 25 V Ceramic-Disc Axial-Lead Capacitor | 122002-104 |
| C82 | 0.001 uF, 100 V Radial-Lead Mylar Capacitor | 21-101102 |
| C83-C88 | 0.1 pF, +10%, 25 V Ceramic-Disc Axial-Lead Capacitor | 122002-104 |
| c89 | 100 pF, 100 V Mica Capacitor | 128002-101 |
Diodes
| CRI | Type-MV5053 Light-Emitting Diode | 38-MV5053 |
| CR2 | Type-1N4735A 6.2 V, +5%, 1 W Zener Diode | 131009-001 |
| CR3, CR4 | Type-1N914 100 V, Switching Diode | 31-1N914 |
| CRS | Type-1N4001, 50 V Rectifier Diode | 31-1N4001 |
| CR6 | Type-1N748A 3.9 V +5%, Zener Diode | 131000-002 |
| CR7-CR12 | Type-1N914 100 V, Switching Diode | 31-1N914 |
(Continued on next page)
3-11
Parts Lists C0-218-12
Atari Pole Position Il Central Processing Unit Printed-Circuit Board Assembly Parts List, continued
Designator Description Part No.
Integrated Circuits
| 3c | Type-74L$373 Integrated Circuit | SP-TALS373 | |
| 3M/N | ‘Type-74S32 Integrated Circuit | . | F7-74832 |
| 3M, 4C | Type-74LS373 Integrated Circuit | S-74LS373 | |
| 4M | Type-74LS373 Integrated Circuit | S774LS373 | |
| 5A | Type-74LS74 Integrated Circuit | S7-TALS74 | |
| 5D | Type-74LS367 Integrated Circuit | S7-74LS367 | |
| SE | Type-74LS244 Integrated Circuit | S7-TALS244 | |
| 5J | Type-74LS367 Integrated Circuit | 37-74LS367 | |
| 5K | Type-74LS244 Integrated Circuit | S7-74LS244 | |
| 5L | Type-74LS368 Integrated Circuit | 137168-001 | |
| 5M | Type-74LS158 Integrated Circuit | 137203-001 | |
| 5N | Type-74LS74 Integrated Circuit | S7-TALS74 | |
| 6A | Type-74LS161 Integrated Circuit | S7-74LS161 | |
| 6C | Type-74LS74 Integrated Circuit | ST-TALS74 | |
| 6D-6F | Type-74LS367 Integrated Circuit | 37-74LS367 | |
| 6J, 6K | ‘Type-74LS157 Integrated Circuit | S7-74LS157 | |
| 6L | Type-74LS109 integrated Circuit | 37-74LS109 | |
| 6M | Type-74LS00 Integrated Circuit | 37-74LS00 | |
| 6N | Type-74S163 Integrated Circuit | Acceptable substitute is part no. 137287-001 | 137274-001 |
or 137287-002
| TKIL | ‘Type-74LS138 Integrated Circuit | 137177-001 |
| 7L | Type-74LS139 Integrated Circuit | S7-TALS139 |
| 7N | ‘Type-74S04 Integrated Circuit | 3774804 |
| 8D | ‘Type-74L.S138 Integrated Circuit | 187177-001 |
| 8E | Type-74LS259 Integrated Circuit | S7-TALS259 |
| 8F | Type-74LS367 Integrated Circuit | S7-TALS367 |
| au | Type-ADC0804 Integrated Circuit | 137273-001 |
| 8K | Type-4066 Integrated Circuit | 37-4066 |
| 8L | Type-4584B Integrated Circuit | 37-4584B |
| 8M | Type-74S04 Integrated Circuit | 3774804 |
| 9FIB | Type-LM324 Integrated Circuit | S7-LM324 |
| 404 | Type-74LS138 Integrated Circuit | 137177-001 |
| 10C | Type-74S374 Integrated Circuit | 137206-001 |
| 10D | Type-74LS174 Integrated Circuit | S7-TALS174 |
| 10E, 10F | Type-74LS283 Integrated Circuit | 137204-001 |
| 10H, 103 | Type-74LS273 Integrated Circuit | S7-74LS273 |
| 10K, 10L | Type-4066 Integrated Circuit | 37-4066 |
| TA | Type-74LS174 Integrated Circuit | S7-74LS174 |
| 1c | Type-7497 Integrated Circuit | S7-7497 |
| NE | Type-74LS273 Integrated Circuit | S7-TALS273 |
| 11F | Type-4051 Integrated Circuit | 137277-001 |
| TH | Type-74LS174 Integrated Circuit | SPTALS174 |
| WW | Type-74LS273 Integrated Circuit | S7-7ALS273 |
| 11K-11M | Type-4066 Integrated Circuit | 37-4066 |
| 12A | ‘Type-74LS174 Integrated Circuit | S7-74LS174 |
(Continued on next page)
3-12
CO.-218-12 Parts Lists
Atari Pole Position Il Central Processing Unit Printed-Circuit Board Assembly Parts List, continued
Designator Description Part No.
| 12B | Type-7497 Integrated Circuit | 37-7497 |
| 12C | Type-74LS161 Integrated Circuit | S7-74LS161 |
| 12D | Type-74LS393 Integrated Circuit | 37-74LS393 |
| 12H | Type-LM324 Integrated Circuit | S7-LM324 |
| 12) | Type-LM324 Integrated Circuit | S7-LM324 |
| 12M | Type-LM324 Integrated Circuit | S7-LM324 |
for -22 version only
| 2N | Type-12L6 Programmable-Array Logic 1 | 137316-001 | |
| A | Type-Z8002 16-Bit Microprocessor | 137275-001 | |
| 3F, 3H | Custom Integrated Circuit 10 | 137281-001 | |
| 4F, 4H | Custom Integrated Circuit 10 | 137281-001 | |
| 4K | ~s | Custom Integrated Circuit 25 | 137351-001 |
| 4N | Type-2Z8002 16-Bit Microprocessor | 137275-001 | |
| 5C | Type-12L6 Programmable-Array Logic 1 | 137316-001 | |
| 6H | Custom Integrated Circuit 08 | 137186-001 | |
| 7c | Type-10L8 Programmable-~Array Logic 3 | 137279-001 | |
| 7D | Type-Z80A 8-Bit Microprocessor | 137194-001 | |
| 7™M | Custom Integrated Circuit 07 | 137193-001 | |
| 8H | Custom Integrated Circuit 08 | 137186-001 | |
| 9E | Custom Integrated Circuit 52 | 137284-001 | |
| OFA | Custom Integrated Circuit 54 | 137285-001 | |
| 9H | Custom Integrated Circuit 06 | 137192-001 | |
| 9K | Custom Integrated Circuit 53 | 137188-001 | |
| 9M | Custom Integrated Circuit 51 | 137187-001 |
Random-Access Memories
| vA) | RandomAccess Memory | 137199-001 |
| 7K | Random-Access Memory | 137199-001 |
Read-Only Memory
| 1D | Programmable Read-Only Memory | 136014-118 |
for -22 version only
| 7E | CMOS Random-Access Memory | 137278-001 | |
| 9C | Electrically Programmable Read-Only Memory | Acceptable substitute is | 136014-106 |
Part no. 136014-147,
| 3D | -@ | Electrically Programmable Read-Only Memory | 136014-184 |
| 3E | «@ | Electrically Programmable Read-Only Memory | 136014-178 |
| 3L | “SH —_ Electrically Programmable Read-Only Memory | 136014-176 | |
| 4D | -@8 = Electrically Programmable Read-Only Memory | 136014-185 | |
| 4E | «8 = Electrically Programmable Read-Only Memory | 136014-179 | |
| 4L | - — Electrically Programmable Read-Only Memory | 136014-177 | |
| 7F | 3 | Electrically Programmabie Read-Only Memory | 136014-183, |
| 7H | a) | Electrically Programmable Read-Only Memory | 136014-180 |
| 12E | cy | Electrically Programmable Read-Only Memory | 136014-182 |
| 12F | “aS | Electrically Programmable Read-Only Memory | 136014-181 |
-@8 New to Pole Position II. (Continued on next page)
3-13
Parts Lists CO-218-12
Atari Pole Position II Central Processing Unit Printed-Circuit Board Assembly Parts List, continued
Designator Description Part No. Resistors
| Rt | 2200, +5%, Ys W Resistor | 110000-221 | |
| R2-R8 | 2.2 kQ, +5%, Va W Resistor | 110000-222 | |
| RQ | 1kQ, +5%, % W Resistor | 110000-102 | |
| R10-R16 | 2.2 kQ, +5%, V4 W Resistor | 110000-222 | |
| R17-R26 | 1kQ, +5%, Ys W Resistor | 110000-102 | |
| R27-R34 | 2.2 kQ, +5%, Ya W Resistor | 110000-222 | |
| R35 | 1k, +5%, % W Resistor | 110000-102 | |
| R36-R38 | 2.2kQ, +5%, Ya W Resistor | 110000-222 | |
| R39-R43 | 1kQ, +5%, Ys W Resistor | 110000-102 | |
| R45 | 470, +5%, Ys W Resistor | 110000-470 | |
| R46, R47 | 1kQ, +5%, Y% W Resistor | 110000-102 | |
| R52 | 470.0, +5%, Ya W Resistor | 110000-471 | |
| R53 | 1k, +5%, % W Resistor | 110000-102 | |
| R54 | 470.9, +5%, Va W Resistor | 110000-471 | |
| R55, R56 | 1kQ, +5%, 4 W Resistor | 110000-102 | |
| R57-R60 | 470.0, +5%, Ys W Resistor | 110000-471 | |
| R61 | 4.7kQ, +5%, % W Resistor | 110000-472 | |
| R62 | 10 kQ, +5%, % W Resistor | 110000-103 | |
| R63 | 22 kQ, +5%, Vs W Resistor | 110000-223 | |
| R64 | 47 kQ, +5%, Ya W Resistor | 110000-473 | |
| R65 | 4.7 kQ, +5%, V4 W Resistor | 110000-472 | |
| R66 | 10 kQ, +5%, ¥%4 W Resistor | 110000-103 | |
| R67 | 22 kM, +5%, Va W Resistor | 110000-223 | |
| R68 | 47k, +5%, Ys W Resistor | 110000-473 | |
| R69 | 4.7 kQ, +5%, Ys W Resistor | 110000-472 | |
| R70 | 10 kQ, +5%, Vs W Resistor | 110000-103 | |
| R71 | 22 kQ, +5%, Vs W Resistor | 110000-223 | |
| R72 | 47 kQ, +5%, Vs W Resistor | 110000-473 | |
| R73 | 4.7kQ, +5%, Ys W Resistor | 110000-472 | |
| R74 | 10 kQ, +5%, ¥% W Resistor | 110000-103 | |
| R75 | 22 kQ, +5%, Ys W Resistor | 110000-223 | |
| R76 | 47 kQ, +5%, Ya W Resistor | 110000-473 | |
| R77-R80 | 1kQ, +5%, % W Resistor | 110000-102 | |
| R81 | 2200, +5%, Ys W Resistor | 110000-221 | |
| R82 | 1kQ, +5%, % W Resistor | 110000-102 | |
| R83 | 470.0, +5%, Ys W Resistor | 110000-471 | |
| Re4 | 1kQ, +5%, % W Resistor | 110000-102 | |
| R85 | 2.2kQ, +5%, V4 W Resistor | 110000-222 | |
| R86 | 330.2, +5%, % W Resistor | 110000-331 | |
| R87 | 1kQ, +5%, Ys W Resistor | 110000-102 | |
| Res | 22 kM, +5%, Vs W Resistor | 110000-223 | |
| R89 | 1000, +5%, Ys W Resistor | 110000-101 | |
| R90-R92 | 1kQ, +5%, ¥ W Resistor | 110000-102 | |
| R93, R94 | 3300, +5%, v4 W Resistor | 110000-331 | |
| R95 | 1kQ, +5%, Ys W Resistor | 110000-102 | |
| R96 | 4.7, +5%, ¥4 W Resisior | 110000-472 | |
| R97 | 2200, +5%, Ye W Resistor | (Continued on next page) | 110000-221 |
3-14
CO-218-12 Parts Lists
Atari Pole Position II Central Processing Unit Printed-Circuit Board Assembly Parts List, continued
Designator Description Part No.
| ROB | 4.7kQ, +5%, Ys W Resistor | 110000-472 |
| R99 | 2209, +5%, Vs W Resistor | 110000-221 |
| Riot | 2.2k0, +5%, %& W Resistor | 110000-222 |
| R102, R104 | 1k0, +5%, %4 W Resistor | 110000-102 |
| R103 | 4.7kQ, +5%, Ys W Resistor | 110000-472 |
| R106 | 1kQ, +5%, % W Resistor | 110000-102 |
| R107 | 4.7k0, +5%, Ys W Resistor | 110000-472 |
| 108-115 | 1k0, +5%, % W Resistor | 110000-102 |
| R116 | 15 kQ, +5%, Ys W Resistor | 110000-152 |
| Rti7 | 1kO, +5%, % W Resistor | 110000-102 |
| R18 | 47k, +5%, Ys W Resistor | 110000-472 |
| R119 | 10 kO, +5%, Vs W Resistor | 110000-103 |
| R120, R121 | 22k, +5%, 4 W Resistor | 110000-223 |
| R122 | 120k, +5%, % W Resistor | 110000-124 |
| R123 | 470.0, +5%, Y% W Resistor | 110000-471 |
| R124 | 47 KO, +5%, Vs W Resistor | 110000-473 |
| R125 | 12k, +5%, 4 W Resistor | 110000-123 |
| R126 | 4.7kQ, +5%, Ys W Resistor | 110000-472 |
| R127, R128 | 2.2k0, +5%, % W Resistor | 110000-222 |
| R129, R130 | 33k0, +5%, %4 W Resistor | 110000-332 |
| R131 | 10 kO, +5%, Ya W Resistor | 110000-103 |
| R132 | 22 k0, +5%, Ys W Resistor | 110000-223 |
| R133 | 15k, +5%, % W Resistor | 110000-153 |
| R134 | 120 kM, +5%, % W Resistor | 110000-124 |
| R135 | 470.0, +5%, Ys W Resistor | 110000-471 |
| R136 | 47 KO, +5%, % W Resistor | 110000-473 |
| R137 | 15k, +5%, 4 W Resistor | 110000-153 |
| R138 | 10 k2, +5%, V4 W Resistor | 110000-103 |
| R139 | 22k, +5%, % W Resistor | 110000-223 |
| R140 | 180k, +5%, % W Resistor | 110000-184 |
| R141 | 470.9, +5%, Ys W Resistor | 110000-471 |
| R142, R143 | 22 kK, +5%, 4 W Resistor | 110000-223 |
| R144-R151 | 1k0, 5%, % W Resistor | 110000-102 |
| R152 | 47 kQ, +5%, Ye W Resistor | 110000-473 |
| R153 | 470.0, +5%, Y% W Resistor | 110000-471 |
| R154 | 10k, +5%, % W Resistor | 110000-103 |
| R155 | 82k, +5%, V4 W Resistor | 110000-823 |
| R156, R157 | 47 kQ, +5%, % W Resistor | 110000-473 |
| R158 | 22k, +5%, Ya W Resistor | 110000-223 |
| R159 | 47 KO, +5%, ¥% W Resistor | 110000-473 |
| R160 | 100k, +5%, Y W Resistor | 110000-104 |
| R161-R165 | 2.2k0, +5%, % W Resistor | 110000-222 |
| R166 | 1k0, +5%, % W Resistor | 110000-102 |
| R167 | 2.2k0, +5%, % W Resistor | 110000-222 |
| Ries | 4.7kQ, +5%, Vs W Resistor | 110000472 |
| R169 | 220 kM, +5%, %& W Resistor | 110000-224 |
| R170 | 390 KO, +5%, % W Resistor | 110000-394 |
(Continued on next page)
3415
Parts Lists CO-218-12
Atari Pole Position Il Central Processing Unit Printed-Circuit Board Assembly Parts List, continued
Designator Description Part No.
| RIN | 4.7 kQ, +5%, Vs W Resistor | 110000-472 |
| Ri72 | 15 kQ, +5%, Ys W Resistor | 110000-153 |
| R173 | 47 kQ, +5%, Ys W Resistor | 110000-473 |
| R174 | 33 kQ, +5%, V4 W Resistor | 110000-333 |
| R175 | 10 kQ, +5%, Va W Resistor | 110000-103 |
| RI76 | 47 kQ, +5%, Ya W Resistor | 110000-473 |
| RI77 | 1kQ, +5%, Ya W Resistor | 110000-102 |
| R178 | 75 kQ, +5%, V4 W Resistor | 110000-752 |
| R179 | 330 kQ, +5%, % W Resistor | 110000-334 |
| R180, R181 | 47 kQ, +5%, Va W Resistor | 110000-473 |
| R182 | 1kQ, +5%, Ya W Resistor | 110000-102 |
| R183 | 22 kQ, +5%, Va W Resistor | 110000-223 |
| R184 | 15 kQ, +5%, Va W Resistor | 110000-153 |
| R185 | 10 kQ, +5%, Ys W Resistor | 110000-103 |
| R186 | 1kQ, +5%, % W Resistor | 110000-102 |
| R187 | 330 kQ, +5%, Ys W Resistor | 110000-334 |
| R188 | 10k, +5%, Vs W Resistor | 110000-103 |
| R189, R190 | 47 kQ, +5%, Vs W Resistor | 110000-473 |
| R191 | 1kQ, +5%, Y W Resistor | 110000-102 |
| R192 | 75 kf, +5%, %4 W Resistor | 110000-753 |
| R193 | 15 kQ, +5%, Va W Resistor | 110000-153 |
| R194 | 47 kQ, +5%, Va W Resistor | 110000-473 |
| R195, | 10 kQ, +5%, ¥% W Resistor | 110000-103 |
| R196 | 1k, +5%, Y%4 W Resistor | 110000-102 |
| R197, R198 | 47kQ, +5%, Vs W Resistor | 110000-473 |
| Rigg | 1kQ, +5%, Vs W Resistor | 110000-102 |
| R200 | 47 kQ, +5%, Vs W Resistor | 110000-473 |
| R201 | 15 kQ, +5%, Ya W Resistor | 110000-153 |
| R202 | 10 kQ, +5%, %4 W Resistor | 110000-103 |
| R203 | 1kQ, +5%, VY W Resistor | 110000-102 |
| R204, R205 | 47 kQ, +5%, Ys W Resistor | 110000473 |
| R206 | 1kQ, +5%, Ys W Resistor | 110000-102 |
| R207 | 20 kQ, +5%, Ya W Resistor | 110000-203 |
| R208 | 10 kQ, +5%, % W Resistor | 110000-103. |
| R209 | 20 kQ, +5%, Ya W Resistor | 110000-203 |
| R210 | 10 kQ, +5%, Ya W Resistor | 110000-103 |
| Ratt | 20kQ, +5%, Ys W Resistor | 110000-203 |
| R2i2 | 10 kQ, +5%, Ya W Resistor | 110000-103 |
| R213 | 20 kQ, +5%, VY W Resistor | 110000-203 |
| R214 | 10 kQ, +5%, Ya W Resistor | 110000-103 |
| R215 | 20kQ, +5%, V4 W Resistor | 110000-203 |
| R216 | 10kQ, +5%, V4 W Resistor | 110000-103 |
| R217 | 20 kQ, +5%, ¥ W Resistor | 110000-203 |
| R218 | 10 kQ, +5%, ¥% W Resistor | 110000-103 |
(Continued on next page)
CO-218-12 Parts Lists
Atari Pole Position I Central Processing Unit Printed-Circuit Board Assembly Parts List, continued
Designator Description Part No.
| R219 | 20 kQ, +5%, V4 W Resistor | 110000-203 |
| R220 | 27 kQ, +5%, Y4 W Resistor | 110000-273 |
| R223 | 1kQ, +5%, Ya W Resistor | 110000-102 |
| R225-R231 | 1kQ, +5%, Ya W Resistor | 110000-102 |
| R231-R238 | 2.2kQ, +5%, 1% W Resistor | 110000-222 |
| R239-R244 | 1kQ, +5%, %4 W Resistor | 110000-102 |
| R245 | 100.0, +5%, Y W Resistor | 110000-101 |
| R246 | 150 k®, +5%, ¥4 W Resistor | 110000-154 |
| R249 | 1500, +5%, Y W Resistor | 110000-151 |
| 1E | 2.2 kQ, +2%, Dual-Inline-Package Resistor Network | 118003-222 |
| ON | 1k, +2%, Dual-Inline-Package Resistor Network | 118003-102 |
Sockets
| cA | 40-Contact Medium-Insertion-Force integrated Circuit Socket | 79-42C40 |
| 3D | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C28 |
| 3E, 3F | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C28 |
| 3H | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C28 |
| 3k | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C28 |
| 4D | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C28 |
| 4E, 4F | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C28 |
| 4H | 28-Contact Medium-insertion-Force Integrated Circuit Socket | 79-42C28 |
| 4k | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C28 |
| 4 | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C28 |
| 4N | 40-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C40 |
| 6H-9H | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C28 |
| 7D | 40-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C40 |
| 7E, 7F | 24-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C24 |
| 9E | 42-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C42 |
| FIA | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C28 |
| 9K | 42-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42042 |
| 9M | 42-Contact Medium-Iinsertion-Force Integrated Circuit Socket | 79-42C42 |
| 12E, 12F | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C28 |
Switches
| QUA | 8-Siation, SingleThrow, Dual-Inline-Package Bit Switch | 66-118PIT |
| OL | 8-Station, SingleThrow, Dual-Inline-Package Bit Switch | 66-118PIT |
Transistors
| ai | Type-2N3906 40 V, 1 W, PNP Transistor | 33-2N3906 |
| a2 | Type-2N3904 60 V, 350 mW, NPN Transistor | 34-2N3904 |
| a3 | Type MPS-A92 300 V, 500 mA, PNP Transistor | 33-MPSAQ2 |
| a4 | Type-2N3904 60 V, 350 mW, NPN Transistor | 34-2N3004 |
| Q5, Q6 | ‘Type-2N6044 80 V, 8 A, Darlington NPN Transistor | 34-2N6044 |
Miscellaneous Test Point Acceptable substitute is part no. 020670-01 179051-001 Jumper Staple 150009-001
| BT | 36 V, 100 mA Nickel-Cadmium Battery | 171028-001 |
| wi | Lead-Spring Socket Terminal | 179131-001 |
| Q5, Q6 | Nylon Snap-in Fastener | 81-4302 |
-® New to Pole Position Il.
3-17
Parts Lists CO-218-42
Pole Position Il Namco Central Processing Unit Printed-Circuit Board Assembly 171031-001 A Parts List
| Designator | Description | Part No. |
Capacitors
| C1 | 470 nF, 16 V Aluminum Electrolytic Fixed Axial-Lead Capacitor | 24-160477 |
| C2-C4 | 01 uF, +10%, 25 V Ceramic-Disc Axial-Lead Capacitor | 122005-104 |
| C5 | 47 uF, 10 V Aluminum Electrolytic Fixed Axial-Lead Capacitor | 24-100476 |
| C6, C7 | 0,001 :F, 100 V Radial-Lead Mylar Capacitor | 21-101102 |
| ce | 0.1 nF, +10%, 25 V Ceramic-Disc Axial-Lead Capacitor | 122005-104 |
| co | 0.001 uF, 100 V Radial-Lead Mylar Capacitor | 21107102 |
| co | 0.01 pF, +80%, -20%, 25 V Ceramic-Disc Axial-Lead Capacitor | 122005-103 |
| C10 | 0.01 uF, +80%, -20%, 25 V Ceramic-Disc Axial-Lead Capacitor | 122005-103 |
| C11, C12 | 0.0047 uF, 100 V Radial-Lead Mylar Capacitor | 21-101472 |
| C13-C15 | 0.1 uF, +10%, 25 V Ceramic-Disc Axial-Lead Capacitor | 122005-104 |
| C16, C17 | 4.7 nF, +20%, 16 V Radial-Lead Tantalum Capacitor | 121014-475, |
| C18 | 47 uF, 10 V Aluminum Electrolytic Fixed Axial-Lead Capacitor | 24-100476 |
| c19 | 001 pF, +80%, -20%, 25 V Ceramic-Disc Axial-Lead Capacitor | 122005-103 |
| C20 | 0.01 uF, +80%, -20%, 25 V Ceramic-Disc Axial-Lead Capacitor | 122005-103 |
| c21 | 0.1 nF, +10%, 25 V Ceramic-Disc Axial-Lead Capacitor | 122005-104 |
| C22 | 47 uF, 16 V Radial-Lead Mylar Capacitor | 121014-475 |
| C23 | 0.1 nF, +10%, 25 V Ceramic-Disc Axial-Lead Capacitor | 122005-104 |
| C24, C25 | 0.01 pF, +80%, -20%, 25 V Ceramic-Disc Axial-Lead Capacitor | 122005-103 |
| C26 | 0.0022 uF, +10%, 100 V Radial-Lead Mylar Capacitor | 121022-222 |
| C28 | 0.0047 uF, 100 V Radial-Lead Mylar Capacitor | 21-101472 |
| C29 | 0.001 uF, 100 V Radial-Lead Mylar Capacitor | 21-101102 |
| C30, C31 | 0,0022 »F, +10%, 100 V Radial-Lead Plastic Capacitor | 121022-222 |
| C32 | 0.1 uF, +10%, 25 V Ceramic-Disc Axial-Lead Capacitor | 122005-104 |
| C33, C34 | 0.047 uF, 100 V Radial-Lead Mylar Capacitor | 21101473 |
| C35, C36 | 0.0022 uF, +10%, 100 V Radial-Lead Mylar Capacitor | 121022-222 |
| Cor | 0.1 uF, +10%, 25 V Ceramic-Disc Axial-Lead Capacitor | 122005-104 |
| C38-C47 | 001 pF, +80%, -20%, 25 V Ceramic-Disc Axial-Lead Capacitor | 122005-103 |
| C48-C50 | 0.1 uF, +10%, 25 V Ceramic-Disc Axial-Lead Capacitor | 122005-104 |
| C51 | 0.01 uF, +80%, -20%, 25 V Ceramic-Disc Axial-Lead Capacitor | 122005-103 |
| cs2 | 0.1 pF, +10%, 25 V Ceramic-Disc Axial-Lead Capacitor | 122005-104 |
| C53 | 47 yF, 10 V Aluminum Electrolytic Fixed Axial-Lead Capacitor | 24-100476 |
| C54, C55 | 0.1 uF, +10%, 25 V Ceramic-Disc Axial-Lead Capacitor | 122005-104 |
| C56 | 22 uF, 16 V Aluminum Electrolytic Fixed Axial-Lead Capacitor | 24-160226 |
| C57-Cét | 0.1 nF, +10%, 25 V Ceramic-Disc Axial-Lead Capacitor | 122005-104 |
| C62, C63 | 4.7 uF, 16 V Radial-Lead Mylar Capacitor | 121014-475 |
| C64, C65 | Q1 pF, +10%, 25 V Ceramic-Disc Axial-Lead Capacitor | 122005-104 |
| C67, C68 | 0.1 pF, +10%, 25 V Ceramic-Disc Axial-Lead Capacitor | 122005-104 |
| C69 | 4,7 uF, 16 V Radial-Lead Mylar Capacitor | 121014-475, |
| C70 | 33 pF, 100 V Radial-Lead Epoxy-Dipped Mica Capacitor | 128002-330 |
| C71-C73 | 0.1 pF, +10%, 25 V Ceramic-Disc Axial-Lead Capacitor | 122005-104 |
(Continued on next page)
3-18
CO-218-12 Parts Lists
Pole Position II Namco Central Processing Unit Printed-Circuit Board Assembly Parts List, continued
Designator Description Part No.
| C74 | 4,7 pF, 16 V Radial-Lead Mylar Capacitor | 121014-475 |
| C75 | 0.1 uF, +10%, 25 V Ceramic-Disc Axial-Lead Capacitor | 122005-104 |
| C76 | 4.7 uF, 16 V Radial-Lead Mylar Capacitor | 121014-475, |
| C77 | 0.1 uF, +10%, 25 V Ceramic-Disc Axial-Lead Capacitor | 122005-104 |
| C78 | 4,7 uF, 16 V Radial-Lead Mylar Capacitor | 121014-475 |
| C79-C81 | 01 wF, +10%, 25 V Ceramic-Disc Axial-Lead Capacitor | 122005-104 |
| C83 | 0.1 uF, +10%, 25 V Ceramic-Disc Axial-Lead Capacitor | 122005-104 |
| C84 | 33 pF, 100 V Radial-Lead Epoxy-Dipped Mica Capacitor | 128002-330 |
| C85-87 | 0.1 uF, +10%, 25 V Ceramic-Disc Axial-Lead Capacitor | 122005-104 |
| C88, C89 | 1000 »F, 100 V Epoxy-Dipped Mica Capacitor | 128002-002 |
| C90 | 01 uF, +10%, 25 V Ceramic-Disc Axial-Lead Capacitor | 122005-104 |
Diodes
| D1 | 62 V, 1 W Type-1N4735A Zener Diode | 131009-001 |
| D2-D9 | 75 V, Type-1N914 Switching Diode | 31-1N914 |
| D10 | 33 V +5% Zener Diode | 131014-001 |
Integrated Circuits
| 1A, 1B | Type-74LS174 Integrated Circuit | SPTALS174 |
| 1c | Type-74LS138 Integrated Circuit | 137177-001 |
| W | ‘Type-74LS161 Integrated Circuit | S7-74LS161 |
| 1K | Type-74LS74 Integrated Circuit | S7-TALS74 |
| aL | Type-Z8002 16-Bit Microprocessor | 137275-001 |
| 2A, 2B. | ‘Type-7497 Integrated Circuit | 37-7497 |
| 2c | ‘Type-74LS374 Integrated Circuit | S7-74LS374 |
| 2H | Type-10L8 Programmable-Array Logic 3 | 137279-001 |
| 2J | Type-74LS74 Integrated Circuit | ST-TALS74 |
| 2K | ‘Type-12L6 ProgrammableArray Logic 1 | 137280-001 |
| 2L, 2M | ‘Type-74LS373 Integrated Circuit | S7-74LS373 |
| 3A | Type-74LS138 Integrated Circuit | 137177-001 |
| A | Type-74LS161 Integrated Circuit | S7-74LS161 |
| 3c | Type-74LS174 Integrated Circuit | ST-TALS174 |
| 3D | Custom Integrated Circuit 52 | 137284-001 |
| 3H | Type-Z80A 8-Bit Microprocessor | 137194-001 |
| BU, 3K | Type-74LS367 Integrated Circuit | S7-74LS367 |
| 4A | Type-74LS393 Integrated Circuit | S7-74LS393 |
| 4B | Type-74LS273 Integrated Circuit | S7-TALS273 |
| 4c | Type-74LS283 Integrated Circuit | 137204-001 |
| 4E | Custom Integrated Circuit 54 | 137285-001 |
| 4F | Type-74LS259 integrated Circuit | ST-TALS259 |
| 4d | Type-74LS367 Integrated Circuit | S7-TALS367 |
| 4k | Type-74LS244 Integrated Circuit | S7TALS244 |
| 5B | ‘Type-4051 Integrated Circuit | 137277-001 |
| 5C | Type-74LS283 Integrated Circuit | 137204-001 |
| 5D | Type-LM324 Integrated Circuit | S7-LM324 |
| SF | Type-74LS367 Integrated Circuit | S7-74LS367 |
(Continued on next page)
Parts Lists CO0-218-12
Pole Position I! Namco Central Processing Unit Printed-Circuit Board Assembly Parts List, continued
Designator Description Part No.
| BJ | Type-74LS367 Integrated Circuit | S-TALS367 | |
| SL, 5M | Custom Integrated Circuit 10 | 197281-001 | |
| 6B | Type-74LS174 Integrated Circuit | ST-TALS174. | |
| 6c | ‘Type-74LS273 Integrated Circuit | SPTALS273 | |
| 6E | Custom Integrated Circuit 06 | 137192-001 | |
| 6F | Custom Integrated Circuit 08 | 137186-001 | |
| 6s | Custom Integrated Circuit 08 | 137186-001 | |
| 6L, 6M | Custom Integrated Circuit 10 | 137281-001 | |
| 7B, 7C | ‘Type-74LS273 Integrated Circuit | S-TALS273 | |
| vA) | Type-74LS157 Integrated Circuit | STTALS157 | |
| 7a | os | Custom Integrated Circuit 25 | 137351001 |
| BA | Type-LM324 Integrated Circuit | S7-LM324 | |
| 8B, 8C | Type-4066 integrated Circuit | ‘S7-4066 | |
| 8D | Custom Integrated Circuit 53 | 137188-001 | |
| 8F | Type-4066 Integrated Circuit | 37-4066 | |
| a | Type-74LS157 Integrated Circuit | S7-TALS157 | |
| 8k | Type-74LS244 Integrated Circuit | 37-74LS244 | |
| 9B, 9C | ‘Type-4066 integrated Circuit | 57-4066 | |
| ey] | Type-74LS109 Integrated Circuit | STTALS109 | |
| 9K | Type-74LS368 Integrated Circuit | 137168-001 | |
| 9L, 9M | Type-74LS373 Integrated Circuit | S-TALSS73 | |
| 104 | Type-LM324 Integrated Circuit | STLM324 | |
| 10B | ‘Type-4066 Integrated Circuit | ‘37-4066 | |
| 10D | Custom integrated Circuit 51 | 137187-001 | |
| 10H | Custom Integrated Circuit 07 | 137193-001 | |
| 105 | Type-74LS00 Integrated Circuit | 37-74LS00 | |
| 10L | Type-Z8002 16-Bit Microprocessor | 137275-001 | |
| 1H | Type-74804 Integrated Circuit | 3774804 | |
| Nd | Type-74S161 Integrated Circuit | 137274-001 | |
| TL | Type-74LS74 Integrated Circuit | S7-74LS74 | |
| 11M | Type-12L6 Programmable-Array Logic 1 | 137280-001 |
Random-Access Memories
| 4H | Static-2048x8 (200 ns) CMOS Random-Access Memory | 137278-001 |
| 7H | Static-1024x4 (65 ns) Random-Access Memory | 137199-001 |
| 8H | Static-1024x4 (55 ns) Random-Access Memory | 137199-001 |
Read-Only Memories
| 2E | Electrically Programmable Read-Only Memory 11 | 136014-106 | |
| 3B | Programmable Read-Only Memory 5 | 136014-118 | |
| 3k | ~o | Electrically Programmable Read-Only Memory | 136014-185 |
| 3M | os | Electrically Programmable Read-Only Memory | 136014-184 |
-@ New to Pole Position Il.
(Continued on next page)
3-20
c0-218-12 Parts Lists
Namco Central Processing Unit Printed-Circuit Board Assembly Parts List, continued
Designator Description Part No.
| 4u | os | Electrically Programmable Read-Only Memory 6 | 136014-179 |
| 4M | oe | Electrically Programmable Read-Only Memory 5 | 136014-178 |
| 5A | a | Electrically Programmable Read-Only Memory 16 | 136014-182 |
| 5H | ~-s | Electrically Programmable Read-Only Memory 10 | 136014-183 |
| 6A | oa | Electrically Programmable Read-Only Memory 15 | 136014-181 |
| 6H | ce) | Electrically Programmable Read-Only Memory 9 | 136014-180 |
| 8L | wos | Electrically Programmable Read-Only Memory 2 | 136014-177 |
| 8M | so | Electrically Programmable Read-Only Memory 1 | 136014-176 |
| 9H | oe | Programmable Read-Only Memory 4 | 136014-117 |
Resistors
| RM1 | 1 kQ, 4-Station, 5-Pin, Single-Inline-Package Resistor Network | 118001-102 |
| RM2 | 2.2 kQ, 4-Station, 5-Pin, Single-Inline-Package Resistor Network | 118001-222 |
| RM3 | 1 kQ, 8Station, 9-Pin, Single-Inline-Package Resistor Network | 118002-102 |
| RM4 | 2.2 kQ, 4-Station, 5-Pin. Single-Inline-Package Resistor Network | 118000-222 |
| RM5 | 1 kQ, 8-Station, ¢-Pin, Single-Inline-Package Resistor Network | 118002-102 |
| RM6, RM7 | 2.2 kQ, 4-Station, 5-Pin, Single-Inline-Package Resistor Network | 118000-222 |
| RM8 | 1 kQ, 8-Station, 9-Pin, Single-Inline-Package Resistor Network | 118002-102 |
| RM10 | 1 kf, 4Station, 5-Pin, Single-Inline-Package Resistor Network | 118001-102 |
| RM11, RM12 | 470 0, 4-Station, 5-Pin, Single-Inline-Package Resistor Network | 118001-474 |
| RM13, | 2.2 kQ, 8-Station, 9-Pin, Single-Inline-Package Resistor Network | 118002-222 |
| RM14 | 10, 4-Station, 5-Pin, Single-Inline-Package Resistor Network | 118001-102 |
| RM14-R16 | 1 kQ, 4-Station, 5-Pin, Single-Inline-Package Resistor Network | 118001-102 |
| RM17-R20 | 2.2 kQ, 8-Station, 9-Pin, Single-Inline-Package Resistor Network | 118002-222 |
| RM21-R23 | 1kQ, 4-Station, 5-Pin, Single-Inline-Package Resistor Network | 118001-102 |
| Ri | 1kQ, +5%, % W Resistor | 110000-102 |
| Re, R3 | 20k0, +5%, Ya W Resistor | 110000-203 |
| R4, RS | 10kQ, +5%, % W Resistor | 110000-103 |
| R6, R7 | 20 kQ, +5%, Ys W Resistor | 110000-203 |
| R8 | 27 kQ, +5%, Ya W Resistor | 110000-273 |
| R9-R11 | 20k, +5%, Ys W Resistor | 110000-203 |
| Ri2 | 330 kQ, +5%, % W Resistor | 110000-334 |
| RI3 | 120 kM, +5%, ¥4 W Resistor | 110000-124 |
| Ri4 | 75k, +5%, % W Resistor | 110000-753 |
| RI15-R19 | 10 kQ, +5%, % W Resistor | 110000-103 |
| R20 | 33k0, +5%, % W Resistor | 110000-333 |
| R21 | 220 KO, +5%, Ya W Resistor | 110000-224 |
| R22 | 390 kM, +5%, % W Resistor | 110000-394 |
| R23 | 330 kM, +5%, Y W Resistor | 110000-334 |
| R24 | 150 kM, +5%, Y W Resistor | 110000-154. |
| Ras | 22 kQ, +5%, Ya W Resistor | 110000-223 |
| R26 | 47k, +5%, % W Resistor | 110000-472 |
| R27 | 75 kQ, +5%, Ya W Resistor | 10000-752 |
#5 New to Pole Position Il.
(Continued on next page)
3-21
Parts Lists. CO-218-12
Pole Position II Namco Central Processing Unit Printed-Circuit Board Assembly Parts List, continued
Designator Description Part No.
| R28 | 22.k0, +5%, ¥%4 W Resistor | 110000-223 |
| R29 | 15 kQ, +5%, ‘4 W Resistor | 110000-153 |
| R30 | 15 kQ, +5%, %4 W Resistor | 110000-153 |
| R31 | 22 kO, +5%, Ya W Resistor | 110000-223 |
| R32, R33 | 10 kO, +5%, 4 W Resistor | 110000-103 |
| R34 | 1k0, +5%, % W Resistor | 110000-102 |
| R35-R37 | 10 kO, +5%, %4 W Resistor | 110000-103 |
| R97 | 1M, £5%, % W Resistor | 110000-102 |
| R38 | 22 k0, +5%, Vs W Resistor | 110000-223 |
| R40 | 15kQ, +5%, % W Resistor | 110000-153 |
| Rat | 22 kf, +5%, Ys W Resistor | 110000-223 |
| R42, 43 | 1k, +5%, % W Resistor | 110000-102 |
| R44 | 2.2 kM, +5%, %& W Resistor | 110000-222 |
| R45, R46 | 1k, +5%, ¥4 W Resistor | 110000-102 |
| Ra7 | 2.2k, +5%, Vs W Resistor | 110000-222 |
| Rag | 4700, +5%, Vs W Resistor | 110000-471 |
| Rag | 2209, +5%, Ya W Resistor | 110000-221 |
| R50-R53 | 470.0, +5%, Ya W Resistor | 110000-471 |
| R54 | 1kO, +5%, Ys W Resistor | 110000-102 |
| R55 | 47k, +5%, ¥4 W Resistor | 110000-472 |
| R56 | 47.9, +5%, % W Resistor | 110600-470 |
| R58 | 22 kQ, +5%, Ys W Resistor | 110000-223 |
| R59 | 4.7 kQ, +5%, Ys W Resistor | 110000-472 |
| Reo | 47 kQ, +5%, Ys W Resistor | 110000-473 |
| Ret | 10k, +5%, % W Resistor | 110000-103 |
| R62 | 22 kD, +5%, Vs W Resistor | 110000-223 |
| R63 | 47 kQ, +5%, Y W Resistor | 110000-472 |
| Re4 | 2.2k, £5%, Ya W Resistor | 110000-222 |
| Res | 1k0, +5%, Ys W Resistor | 110000-102 |
| Res | 47 kQ, +5%, Ys W Resistor | 110000-472 |
| R67 | 47 k0, +5%, Vs W Resistor | 110000-473 |
| R68 | 10 kQ, +5%, Y4 W Resistor | 110000-103 |
| Reo | 22 kf, +5%, Ys W Resistor | 110000-223 |
| R70 | 4.7 kQ, +5%, Ys W Resistor | 110000-472 |
| R72 | 10kQ, +5%, Ys W Resistor | 110000-103 |
| R73 | 22 kO, +5%, Ye W Resistor | 110000-223 |
| R74 | 1kO, 5%, Ys W Resistor | 110000-102 |
| R75 | 15k, +5%, Ys W Resistor | 110000-152 |
| R76 | 1k, +5%, % W Resistor | 110000-102 |
| R77 | 100 k2, 45%, / W Resistor | 110000-104 |
| R78 | 47 KO, +5%, Ys W Resistor | 110000-473 |
| R79 | 82k2, +5%, Y W Resistor | 110000-823 |
| R80 | 10 k®, +5%, Ya W Resistor | 110000-103 |
| Rei | 22 kQ, +5%, Ya W Resistor | 110000-223 |
(Continued on next page)
3-22
CO-218-12 Parts Lists
Pole Position II Namco Central Processing Unit Printed-Circuit Board Assembly Parts List, continued
Designator Description Part No.
| R82 | 12kQ, +5%, v4 W Resistor | 110000-123 |
| Res | 120 k®, +5%, % W Resistor | 110000124 |
| R84 | 47 kQ, +5%, Ye W Resistor | 110000473 |
| Res | 22k, +5%, Ya W Resistor | 110000-223 |
| Re6 | 10kQ, +5%, 4 W Resistor | 110000-103 |
| R87 | 4.7 kQ, +5%, % W Resistor | 110000-472 |
| Res | 47 kQ, +5%, Y W Resistor | 110000-473 |
| R89 | 22k, +5%, Ya W Resistor | 110000-223 |
| R90 | 10 k0, +5%, % W Resistor | 110000-103 |
| RQt | 4.7 kQ, +5%, Ya W Resistor | 110000-472 |
| R92 | 4,7 kQ, +5%, Ys W Resistor | 110000-472 |
| Re3 | 10 k®, +5%, Ys W Resistor | 110000-103 |
| R94 | 22 kO, +5%, Ya W Resistor | 110000-223 |
| Ros | 47 k0, +5%, % W Resistor | 110000-473 |
| R96, R97 | 22k0, +5%, Y% W Resistor | 110000-223 |
| ROB | 15 kA, +5%, Ye W Resistor | 110000-153 |
| R99 | 180 kQ, +5%, % W Resistor | 110000184 |
| R100 | 120 kQ, +5%, VY W Resistor | 110000-124 |
| Ri0t | 22k, +5%, Ya W Resistor | 110000-223 |
| R102 | 15k, 45%, % W Resistor | 110000153 |
| Ri03 | 1k9, +5%, % W Resistor | 110000-102 |
| R104 | 100.2, +5%, Y W Resistor | 110000-101 |
| R105 | 1kO, +5%, %4 W Resistor | 110000-102 |
| R106 | 1k®, £5%, %4 W Resistor | 110000102 |
| RI07 | 2200, 45%, % W Resistor | 110000-221 |
| R108 | 1kQ, +5%, ‘4 W Resistor | 110000-102 |
| R109 | 1k, +5%, % W Resistor | 410000-102 |
| R110 | 2.2kM, +5%, % W Resistor | 110000-222 |
| RIAN | 1k, +5%, %4 W Resistor | 110000-102 |
| Rt4 | 22kN, +5%, %4 W Resistor | 110000-223 |
| RI15-R117 | 1kQ, +5%, % W Resistor | 110000-102 |
| R18 | 3309, +5%, ¥4 W Resistor | 110000-331 |
| Rt19-RI121 | 1k, +5%, 4 W Resistor | 110000-102 |
| R122 | 3309, +5%, % W Resistor | 410000-331 |
| R123 | 1k, +5%, ¥4 W Resistor | 110000-102 |
| R124 | 479, £5%, % W Resistor | 410000-470 |
| R125 | 470.0, +5%, Ya W Resistor | 110000-471 |
| R126 | 1k, £5%, Y4 W Resistor | 110000-102 |
| R127 | 4.7kQ, +5%, V4 W Resistor | 110000-472 |
| R128 | 1k®, +5%, %4 W Resistor | 110000-102 |
| R129 | 1k0, +5%, % W Resistor | 410000-102 |
| R130 | 470.9, +5%, Vs W Resistor | 410000-471 |
| RI31-R136 | 1kQ, +5%, Ys W Resistor | 410000-102 |
| R137 | 47 KO, 45%, V4 W Resistor | 110000-473 |
| Rise | 4.7 k0, 5%, % W Resistor | 110000472 |
(Continued on next page)
3-23
Parts Lists co-218.12
Pole Position Il Namco Central Processing Unit Printed-Circuit Board Assembly Parts List, continued
Designator Description Part No. Sockets
| AL | 40-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C40 |
| 1E, 1F | 28-Contact Medium-insertion-Force Integrated Circuit Socket | 79-42C28 |
| 2, 2F | 28-Contact Medium-insertion-Force Integrated Circuit Socket | 79-42C28 |
| 3D | 42-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C42 |
| 3H | 40-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C40 |
| 3L, 3M | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C28 |
| 4E | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C28 |
| 4L, 4M | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C28 |
| 5A | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C28 |
| 5H | 24-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C024 |
| 5L, 5M | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C28 |
| CA | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C28 |
| 6E, 6F | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C28 |
| 6H | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C28 |
| CN} | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C28 |
| 6L, 6M | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C28 |
| 7L, 7M | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C28 |
| 8D | 42-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42042 |
| 8L, 8M | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C28 |
| 10D | 42-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C042 |
| 10H | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C28 |
| 10L | 40-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C40 |
Switches
| Swi | SPST Momentary-Contact Push-Button Switch | 62-001 |
| 7E | 8-Station, Single-Throw, Dual-Inline-Package Bit Switch | 66-118P1T |
| 9E | 8-Station, SingleThrow, Dual-Inline-Package Bit Switch | 66-118P1T |
Transistors
| ai | 60 V, 350 mW, Type-2N3904 NPN Transistor* | 34-2N3904 |
| Q2 | 300 V, 500 mA, Type-MPS-A92 PNP Transistor* | 33-MPSA92 |
| Q3 | 60 V, 350 mW, Type-2N3904 NPN Transistor* | 34-2N3904 |
| Q4 | 40 V, 1 W, Type-2N3906 PNP Transistor* | 33-2N3906 |
| 10F | Darlington Quad Transistor Array | 137213-001 |
Miscellaneous
| BT1 | 63 V, 100 mA Nickel-Cadmium Battery | 171038-001 |
| Jt | 60-Pin Connector | 179157-060 |
| J2 | 3-Pin Power Connector | 179156-003 |
Ye-Inch Nylon Standoff 178050-008
34-Inch Nylon Spacer 178020-750 # M3 x 10mm Pan-Head Stainless Stee! Machine Screw 176017-010 # M3 Metric Split-Lock Washer 175006-002 # M3 Metric Stainless Stee! Flat Washer 175005-002
# M3 Metric Stainless Steel Hex Nut 177005-002 Printed-Circuit Board Brace 039562-01 Test Point Acceptable substitute is part no. 020670-01 179051-001
- Orientation of leads not pin-compatible between Namco part and Atari part. See Schematic Package for pin configuration.
3-24
CO-218-12 Parts Lists
Atari Pole Position Il Video Printed-Circuit Board Assembly A039187-22 A Parts List
| Designator | Description | Part No. |
Capacitors
| c2 | 470 uF, 25 V Aluminum Electrolytic Axial-Lead Capacitor | Acceptable substitute | 24-160477 |
is part no. 24-100477
| C3-C17 | 22 uF, 16 V Aluminum Electrolytic Axial-Lead Capacitor | Acceptable | 24160226 |
substitute is part no. 24-250226 or 24-350226
| C18-C57 | 0.1 uF, + 80, -20%, 50 V Ceramic Disk Radial-Lead Capacitor | 122002-104 |
| C58 | 68 pF, 100 V Mica Capacitor | 128002-680 |
| C59 | 22 pF, 100 V Mica Capacitor | 128002-220 |
| C60 | 100 pF, 100 V Mica Capacitor | 128002-101 |
Diodes
| CRI | Type-MV5053 Light-Emitting Diode | 38-MV5053 |
| CR2 | Type-1N4735A, 6.2 V, 1 W Zener Diode | 131009-001 |
Inductors
| L1-L3 | 1 wH, ¥ W Inductor | 141007-001 |
| 4 | 100 nH, +10% Inductor | 141002-001 |
Integrated Circuits
| 2A | Type-74LS138 Integrated Circuit | 137177-001 |
| 2E | Type-74LS74 Integrated Circuit | ST-TALS74 |
| 2H | Type-74LS139 Integrated Circuit | S7-TALS139 |
| 2J | Type-74LS10 Integrated Circuit | S7-TALS10 |
| 2K | Type-74LS368 Integrated Circuit | 137168-001 |
| 3B | Type-74LS283 Integrated Circuit | 137204-001 |
| 3c | Type-74LS283 Integrated Circuit | 137204-001 |
| 3D | Type-74LS283 Integrated Circuit | 137204-001 |
| 3H | Type-74LS175 Integrated Circuit | S7-TALS175, |
| BU, 4d | Type-74LS174 Integrated Circuit | S7-TALS174 |
| 3K | Type-74LS283 Integrated Circuit | 137204-001 |
| 3L | Type-74LS283 Integrated Circuit | 137204-001 |
| 3M | Type-74LS02 Integrated Circuit | SP7ALSO2 |
| 4B | Type-74LS367 Integrated Circuit | S7-74LS367 |
| 4c | Type-74LS367 Integrated Circuit | S7-74LS367 |
| 4H | ‘Type-74LS157 Integrated Circuit | S7-74LS157 |
| 4K | Type-74LS174 Integrated Circuit | S7-TALS174 |
| 4M, 5M | Type-74LS298 Integrated Circuit | 137201-001 |
| 4N, 5N | Type-74LS283 Integrated Circuit | 137204-001 |
| 5B | Type-74LS174 Integrated Circuit | S7-TALS174 |
| 5C | Type-74LS174 Integrated Circuit | STTALS174 |
| 5D | Type-74LS174 Integrated Circuit | S7-TALS174 |
| SE | Type-74LS245 Integrated Circuit | S7-T4LS245 |
| SF, 6F | Type-74LS245 Integrated Circuit | S7-TALS245 |
(Continued on next page)
3-25
Parts Lists C0-218-12
Atari Pole Position Il Video Printed-Circuit Board Assembly Parts List, continued
| Designator | Description | Part No. |
| 5H | Type-74LS175 Integrated Circuit | S7-74LS175, |
| SJ | ‘Type-74LS273 Integrated Circuit | T-TALS273 |
| 6A | Type-74S04 Integrated Circuit | 37-74S04 |
| 6B | ‘Type-74LS368 Integrated Circuit | 137168-001 |
| 6C | Type-74LS08 Integrated Circuit | S7-74LS08 |
| 6H | Type-74LS245 Integrated Circuit | ST-T4LS245 |
| 6J | Type-74LS245 Integrated Circuit | S7TALS245 |
| 6K | Type-74LS245 Integrated Circuit | S7-TALS245 |
| 6M, 7M | Type-74LS273 Integrated Circuit | S7-TALS273 |
| 7B | Type-74S163 Integrated Circuit Acceptable substitute is part no. 137287-001 | 137274-001 |
or -002
| 7C | Type-74S04 Integrated Circuit | S7T4S04 | |
| 7D | Type-74LS32 Integrated Circuit | 37-74LS32 | |
| 7L | Type-74LS273 Integrated Circuit | S7-TALS273 | |
| 8B | Type-74S00 Integrated Circuit | 37-74S00 | |
| 8C,9C | Type-74LS157 Integrated Circuit | S7-74LS157 | |
| 8D | Type-74LS158 Integrated Circuit | 137312-001 | |
| 8E | Type-74LS158 integrated Circuit | 137203-001 | |
| 8L,9L | Type-74LS174 Integrated Circuit | S7TALS174 | |
| 9B | ‘Type-74LS20 Integrated Circuit | ST-7ALS20 | |
| 9D | Type-74LS298 Integrated Circuit | 137201-001 | |
| 9E, 10E | Type-74LS257 Integrated Circuit | S7-74LS257 | |
| 9H | Type-74LS161 Integrated Circuit | 137287-001 | |
| oJ | Type-74LS161 Integrated Circuit | 137287-001 | |
| 9K | Type-7497 Integrated Circuit | 77497 | |
| 9M, 10M | Type-74LS283 Integrated Circuit | 137204-001 | |
| ON | ‘Type-74LS85 Integrated Circuit | S7-TALSBS | |
| 10B | Type-74LS74 Integrated Circuit | ST-TALS74 | |
| 10C | Type-74LS174 Integrated Circuit | ST-T4LS174 | |
| 10D | Type-74LS368 Integrated Circuit | 137168-001 | |
| 10H | Type-74LS161 Integrated Circuit | 137287-001 | |
| 10J | Type-74LS161 Integrated Circuit | 137287-001 | |
| 10K | Type-74LS161 Integrated Circuit | 137287-001 | |
| OL | Type-74LS161 Integrated Circuit | 137287-001 | |
| 10N | Type-74LS85 Integrated Circuit | S7-74LS85 | |
| 1B | Type-74107 Integrated Circuit | Acceptable substitute is part no. 137169-007 | S7-74107 |
| TIF | Type-74LS174 Integrated Circuit | S7-TALS174 | |
| 11H | Type-74LS174 Integrated Circuit | S7-7ALS174 | |
| Wd | Type-74LS273 Integrated Circuit | S7-TALS273 | |
| 11K | Type-74LS139 Integrated Circuit | S7-TALS139 | |
| ML | ‘Type-74LS373 Integrated Circuit | S-TALSI73 |
#8 New to Pole Position Il.
(Continued on next page)
3-26
C0-218-12 Parts Lists
Atari Pole Position Il Video Printed-Circuit Board Assembly Parts List, continued
| Designator | Description | Part No. |
| 11M | Type-74LS373 Integrated Circuit | ST-74LS373 |
| 12B | Type-74LS08 Integrated Circuit | 37-74LS08 |
| 12F | Type-74LS86 Integrated Circuit | S7-7ALS86 |
| 13F | Type-74LS20 Integrated Circuit | S7-TALS20 |
For -22 version only
| 2F | Type-07 Custom Integrated Circuit | 137193-001 |
| 3N | Type-02 Custom integrated Circuit | 137190-001 |
| 4D | Type-09 Custom Integrated Circuit | 137282-001 |
| SL, 6L | Type-03 Custom Integrated Circuit | 137283-001 |
| 7E | Type-04 Custom Integrated Circuit | 137191-001 |
| 8N | Type-02 Custom Integrated Circuit | 137190-001 |
| 13H | Type-02 Custom Integrated Circuit | 137190-001 |
Random-Access Memories
| TF, 8F | Type-2114-2 (200 ns) Random-Access Memory | 90-7036 |
| 7H, 8H | 55 ns Random-~Access Memory | 137199-001 |
| 7d, BJ | Type-2114-2 (200 ns) Random-Access Memory | 90-7036 |
| 7K, 8K | Type-2114-2 (200 ns) Random~Access Memory | 90-7036 |
| 9F, 10F | 55ns Random-Access Memory 343° 77% 7 | 137199-001 |
wer Programmable Read-Only Memories
| 2B | Type-82S129 Programmable Read-Only Memory | 136014-144 |
| 2c | Type-82S129 Programmable Read-Only Memory | 136014-143 |
| 2D | Type-82S129 Programmable Read-Only Memory | 136014-142 |
| 6D | Type-82S123 Programmable Read-Only Memory | 136014-136 |
| 6E | Type-82S123 Programmable Read-Only Memory | 136014-135 |
For -22 version only
| 2L | Electrically Programmable Read-Only Memory | Acceptable substitute is | 136014-127 |
part no. 136014-158
| 2M | Electrically Programmable Read-Only Memory | Acceptable substitute is | 136014-128 |
part no. 136014-159
| 2N | Electrically Programmable Read-Only Memory | 136014-134 | |
| 3E, 4E | Random-Access Memory (200 ns) Acceptable substitute is part no. 137211-001 | 137198-001 | |
| 8 | os | Type-82S137 Programmable Read-Only Memory | 136014-191 |
| ce) | Type-82S129 Programmable Read-Only Memory | 136014-190 | |
| 8M | al | Type-82S129 Programmable Read-Only Memory | 136014-189 |
| 11C | oe | Type-82S129 Programmable Read-Only Memory | 136014-188. |
| 1D | so | Type-82S129 Programmable Read-Only Memory | 136014-187 |
| NE | os | Type-82S129 Programmable Read-Only Memory | 136014-186 |
| os | Type-82S137 Programmable Read-Only Memory | 136014-192 | |
| SF 4F | Random-Access Memory (200 ns) | Acceptable substitute is part no. 137211-001 | 137198-001 |
| 6N | sa | Electrically Programmable Read-Only Memory | 136014-173 |
| 7N | os | Electrically Programmable Read-Only Memory | 136014-172 |
| 11N | Electrically Programmable Read-Only Memory | 136014-231 |
-® New to Pole Position Il.
(Continued on next page)
3-27
Parts Lists CO.218-12
Atari Pole Position Il Video Printed-Circuit Board Assembly Parts List, continued
| Designator | Description | Part No. | |
| 123 | Electrically Programmable Read-Only Memory | Acceptable substitute is | 136014-120 |
part no. 136014-151
| 12K | ~~ | Electrically Programmable Read-Only Memory | 136014-167 |
| 12L | os | Electrically Programmable Read-Only Memory | 136014-169 |
| 12M | ay | Electrically Programmable Read-Only Memory | 136014-174 |
| 12N | os | Electrically Programmable Read-Only Memory | 136014-171 |
| 13d | Electrically Programmable Read-Only Memory Acceptable substitute is | 136014-119 |
part no. 136014-150
| 13K | wn | Electrically Programmable Read-Only Memory | 136014-166 |
| 13L | oso | Electrically Programmable Read-Only Memory | 136014-168 |
| 13M | sos | Electrically Programmable Read-Only Memory | 136014-175, |
| 13N | so | Electrically Programmabie Read-Only Memory | 136014-170 |
Resistors
| R1-R9 | 2.2 kQ, +5%, % W Resistor | 110000-222 |
| R10-R24 | 1 kQ, +5%, Ys W Resistor | 110000-102 |
| R25-R40 | 4700, +5%, % W Resistor | 110000-471 |
| R41-R48- | 4.7 kQ, +5%, Ys W Resistor | 110000-472 |
| R49-R52 | 1kQ, +5%, % W Resistor | 110000-102 |
| R55-R58 | 1kQ, +5%, Ys W Resistor | 110000-102 |
| R59 | 2200, +5%, % W Resistor | 110000-221 |
| Reo | 4702, +5%, v4 W Resistor | 110000-471 |
| R61 | 1kQ, +5%, Ya W Resistor | 110000-102 |
| R62 | 2.2 kQ, +5%, v4 W Resistor | 110000-222 |
| R63 | 1 kQ, +5%, Ya W Resistor | 110000-102 |
| R64, R65 | 820, +5%, % W Resistor | 110000-820 |
| R66 | 220 2, +5%, Va W Resistor | 110000-221 |
| R67 | 470.2, +5%, V4 W Resistor | 110000-471 |
| R68 | 1kQ, +5%, % W Resistor | 110000-102 |
| R69 | 2.2 k2, +5%, ¥%4 W Resistor | 110000-222 |
| R70 | 1kQ, +5%, ¥4 W Resistor | 110000-102 |
| Rat, R72 | 820, +5%, % W Resistor | 110000-820 |
| R73 | 2200, +5%, Va W Resistor | 110000-221 |
| R74 | 4700, +5%, Ya W Resistor | 110000-471 |
| R75 | 1kQ, +5%, % W Resistor | 110000-102 |
| R76 | 2.2kQ, +5%, % W Resistor | 110000-222 |
| R77 | 1kQ, +5%, % W Resistor | 110000-102 |
| R78, R79 | 820, +5%, Ys W Resistor | 110000-820 |
| R80 | 1kQ, +5%, Ys W Resistor | 110000-102 |
| R81 | 100.0, +5%, % W Resistor | 110000-101 |
| R82-R85 | 1kQ, +5%, Y4 W Resistor | 110000-102 |
| R86 | 220 0, +5%, Vs W Resistor | 110000-221 |
| R87-R98 | 1k +5%, Y% W Resistor | 110000-102 |
-@ New to Pole Position II.
3-28 (Continued on next page)
C0-218-12 Parts Lists
Atari Pole Position Il Video Printed-Circuit Board Assembly Parts List, continued
| Designator | Description | Part No. |
| R99 | 10 KO, +5%, % W Resistor | 110000-103 |
| R100 | 2200, +5%, V4 W Resistor | 110000-221 |
| R101 | 10kQ, +5%, % W Resistor | 110000-103 |
| R102 | 470.9, +5%, % W Resistor | 110000-102 |
| R106 | 1502, +5%, ¥4 W Resistor | 110000-151 |
| R107, R1099 | 1k, +5%, % W Resistor | 110000-102 |
| R108, R1100 | 100, +5%, ¥% W Resistor | 110000-101 |
| 1B | 2.2k0, +2%, 15-Element, Dual-Inline Package Resistor Pack | 118003-222 |
| 1K | 2.2k2, +2%, 15-Element, Dual-inline Package Resistor Pack | 118003-222 |
Sockets
| oF | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C28 | |
| aL | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C28 | |
| 2M | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C28 | |
| 2N | 24-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42024 | |
| 3E, 4E | 24-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C024 | |
| SF, 4F | 24-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C24 | |
| 3N | 28-Contact Medium-insertion-Force Integrated Circuit Socket | 79-42C28 | |
| 4D | 24-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C24 | |
| 4L | 16-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C16 | |
| 5K | oo | 16-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C16 |
| BL, 6L | 18-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C18 | |
| 6N, 7N | os | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C28 |
| 7E | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C28 | |
| 8M | 16-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C16 | |
| 8N | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C28 | |
| 11C | 16-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C16 | |
| 11D | 16-Contact Medium-Iinsertion-Force Integrated Circuit Socket | 79-42C16 | |
| NE | 16-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C16 | |
| TIN | 24-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C24 | |
| 12H | os | 18-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C18 |
| 12J, 13) | 28-Contact Medium-insertion-Force Integrated Circuit Socket | 79-42C28 | |
| 12K, 13K | 28-Contact Medium-insertion-Force Integrated Circuit Socket | 79-42C28 | |
| 12L, 13L | 28-Contact Medium-insertion-Force Integrated Circuit Socket | 79-42C28 | |
| 12M | os | 28-Contact Medium-insertion-Force Integrated Circuit Socket | 79-42C28 |
| 12N, 13N | 28-Contact Medium-Iinsertion-Force Integrated Circuit Socket | 79-42C28 | |
| 13H | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C28 | |
| 13M | os | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C28 |
Transistors
| 1-4 | Type-2N3904, 60 V, 1 W, NPN Transistor | 34-2N3904 |
| Q5-Q7 | Type-2N3906, 40 V, 1 W, PNP Transistor | 33-2N3906 |
Miscellaneous Test Points Acceptable substitute is part no. 020670-01 179051-002
| W1, W2 | 02 Jumper Resistor | 110005-001 | |
| YIB | 24576 MHz Crystal | Acceptable substitute is part no. 144004-002 | 144004-003 |
“New to Pole Position Il.
3-29
Parts Lists CO-218-42
Pole Position II Namco Video Printed-Circuit Board Assembly 171032-001 A
| Designator | Description | Part No. |
Capacitors
| C1 | 220 uF 16 V Aluminum Electrolytic Axial-Lead Capacitor | 24-160227 |
| c2 | 0.1 uF, 50 V, +80, -20% Ceramic Capacitor | 122002-104 |
| C3 | 1000 pF 25 V Aluminum Electrolytic Axial-Lead Capacitor | 24-250108 |
| C4 | 22 uF 16 V Aluminum Electrolytic Axial-Lead Capacitor | 24-160226 |
| cS | 220 uF 16 V Aluminum Electrolytic Axial-Lead Capacitor | 24-160227 |
| cé | 0.1 »F, 100 V Mylar Capacitor | 21-101104 |
| C7, C8 | 0.15 uF, +10%, 25 V Solid Tantalum Radial-Lead Capacitor | 121018-154 |
| cg | 0.1 pF, 50 V, +80, -20% Ceramic Capacitor | 122002-104 |
| C10 | 22 uF 16 V Aluminum Electrolytic Axial-Lead Capacitor | 24-160226 |
| cn | 220 uF 16 V Aluminum Electrolytic Axial-Lead Capacitor | 24-160227 |
| C12 | 0.1 uF, 100 V Mylar Capacitor | 21-101104 |
| C13, C14 | 0.15 uF, +10%, 25 V Solid Tantalum Radial-Lead Capacitor | 121018-154 |
| C15 | 0.1 uF, 50 V, +80, -20% Ceramic Capacitor | 122002-104 |
| C16 | 22 yF 16 V Aluminum Electrolytic Axial-Lead Capacitor | 24-160226 |
| Ci7 | 220 uF 16 V Aluminum Electrolytic Axial-Lead Capacitor | 24-160227 |
| C18 | 0.1 uF, 100 V Mylar Capacitor | 21-101104 |
| C19, C20 | 0.15 uF, +10%, 25 V Solid Tantalum Radial-Lead Capacitor | 121018-154 |
| C21 | 0.1 uF, 50 V, +80, -20% Ceramic Capacitor | 122002-104 |
| C22 | 22 uF 16 V Aluminum Electrolytic Axial-Lead Capacitor | 24-160226 |
| C23 | 220 uF 16 V Aluminum Electrolytic Axial-Lead Capacitor | 24-160227 |
| C24 | 0.1 uF, 100 V Mylar Capacitor | 21-101104 |
| C25, C26 | 0.15 uF, +10%, 25 V Solid Tantalum Radial-Lead Capacitor | 121018-154 |
| C27 | 0.1 pF, 50 V, +80, -20% Ceramic Capacitor | 122002-104 |
| C34 | 220 pF, 100 V Fixed Mica Radial-Lead Capacitor | 128002-221 |
| C41-C44 | 1000 pF, 100 V Ceramic Axial-Lead Capacitor | 122016-102 |
| C51-C55 | 0.1 uF, 50 V, +80, -20% Ceramic Capacitor | 122002-104 |
| C56 | 4.7 uF, +20%, 16 V Solid Tantalum Radial-Lead Capacitor | 121014-475 |
| C57 | 0.1 uF, 50 V, +80, -20% Ceramic Capacitor | 122002-104 |
| C58 | 4.7 uF, +20%, 16 V Solid Tantalum Radial-Lead Capacitor | 121014-475 |
| C59-C61 | 0.1 »F, 50 V, +80, -20% Ceramic Capacitor | 122002-104 |
| cé2 | 4.7 uF, +20%, 16 V Solid Tantalum Radial-Lead Capacitor | 121014-475, |
| C63 | 0.1 pF, 50 V, +80, -20% Ceramic Capacitor | 122002-104 |
| C64 | 4.7 uF, +20%, 16 V Solid Tantalum Radial-Lead Capacitor | 121014-475 |
| C65-C67 | 0.1 uF, 50 V, +80, -20% Ceramic Capacitor | 122002-104 |
| C68 | 4.7 pF, +20%, 16 V Solid Tantalum Radial-Lead Capacitor | 121014-475 |
| C69-C71 | 0.1 pF, 50 V, +80, -20% Ceramic Capacitor | 122002-104 |
| c70 | 4.7 uF, +20%, 16 V Solid Tantalum Radial-Lead Capacitor | 121014-475 |
| C72 | 4.7 uF, +20%, 16 V Solid Tantalum Radial-Lead Capacitor | 121014-475 |
| C73 | 0.1 nF, 50 V, +80, -20% Ceramic Capacitor | 122002-104 |
| C74 | 0.1 uF, 50 V, +80, -20% Ceramic Capacitor | 122002-104 |
| C75 | 4.7 uF, +20%, 16 V Solid Tantalum Radial-Lead Capacitor | 121014-475 |
| C76-C79 | 0.1 uF, 50 V, +80, -20% Ceramic Capacitor | 122002-104 |
| C80 | 4.7 uF, +20%, 16 V Solid Tantalum Radial-Lead Capacitor | 121014-475 |
| C81 | 0.1 uF, 50 V, +80, -20% Ceramic Capacitor | 122002-104 |
3-30 (Continued on next page)
Parts Lists CO-218-12
Pole Position II Namco Video Printed-Circuit Board Assembly Parts List, continued
Designator Description Part No.
| C82 | 4.7 pF, +20%, 16 V Solid Tantalum Radial-Lead Capacitor | 121014-475 |
| C83 | 0.1 pF, 50 V, +80, -20% Ceramic Capacitor | 122002-104 |
| C84 | 4.7 uF, +20%, 16 V Solid Tantalum Radial-Lead Capacitor | 121014-475 |
| C85 | 0.1 pF, 50 V, +80, -20% Ceramic Capacitor | 122002-104 |
| C86 | 4.7 pF, +20%, 16 V Solid Tantalum Radial-Lead Capacitor | 121014-475 |
| C87 | 0.1 pF, 50 V, +80, -20% Ceramic Capacitor | 122002-104 |
Integrated Circuits
| 1B | Type-02 Custom Integrated Circuit | 137190-001 | |
| 1c | Type-74LS283 Integrated Circuit | 137204-001 | |
| 1D | Type-74LS283 Integrated Circuit | 137204-001 | |
| W | Type-74LS85 Integrated Circuit | 37-74LS85 | |
| 1K | Type-74LS85 Integrated Circuit | 37-74LS85 | |
| 1M | Type-02 Custom Integrated Circuit | 137190-001 | |
| 2B | Type-74LS02 Integrated Circuit | 37-74LS02 | |
| 2c | Type-74LS298 Integrated Circuit | 137201-001 | |
| 2D | Type-74LS298 Integrated Circuit | 137201-001 | |
| 2E | Type-74LS273 Integrated Circuit | 37-74LS273 | |
| 2F, 3F | Type-74LS273 Integrated Circuit | 37-74LS273 | |
| 20 | Type-74LS283 Integrated Circuit | 137204-001 | |
| 2k | Type-74LS283 Integrated Circuit | 137204-001 | |
| 2b | Type-74LS373 Integrated Circuit | 37-74LS373 | |
| 3B, 4B | Type-74LS283 Integrated Circuit | 137204-001 | |
| 3D | Type-03 Custom Integrated Circuit | 137283-001 | |
| 3E | Type-03 Custom Integrated Circuit | 137283-001 | |
| 3H | Type-74LS174 Integrated Circuit | S7-TALS174 | |
| a | Type-74LS174 Integrated Circuit | 37-74LS174 | |
| 3K-6K | Type-74LS161 integrated Circuit | 37-74LS161 | |
| 3L | Type-74LS375 Integrated Circuit | Acceptable substitute is part no. 137286-002 | 137286-001 |
| 4A | Type-74LS368 Integrated Circuit | 137168-001 | |
| 4C, 5C | Type-74LS174 Integrated Circuit | 37-74LS174 | |
| 4E-7E | Type-74LS245 Integrated Circuit | 37-74LS245, | |
| 4J | Type-7497 Integrated Circuit | 37-7497 | |
| 4L | Type-74LS139 Integrated Circuit | 37-74LS139 | |
| 5A | Type-74LS10 Integrated Circuit | 37-7TALS10 | |
| 5B | Type-74LS174 Integrated Circuit | 37-74LS174 | |
| 5D | Type-74LS273 Integrated Circuit | S7-7T4LS273 | |
| 5J, 6d | Type-74LS161 Integrated Circuit | 37-74LS161 | |
| SL | Type-74LS273 Integrated Circuit | 37-74LS273 | |
| 6A | Type-74LS139 Integrated Circuit | 37-74LS139 | |
| 6B | Type-74LS175 integrated Circuit | S7-TALS175 | |
| 6C | Type-74LS157 Integrated Circuit | 37-74LS157 | |
| 6D | Type-74LS175 Integrated Circuit | S7-TALS175 | |
| 6L, 7L | Type-74LS174 Integrated Circuit | 37-74LS174 | |
| 6N | Type-02 Custom integrated Circuit | 137190-001 | |
| 7A | Type-07 Custom Integrated Circuit | 137193-001 |
(Continued on next page)
3-31
Parts Lists CO.218-42
Pole Position Il Namco Video Printed-Circuit Board Assembly Parts List, continued
| Designator | Description | Part No. | |
| 7D, 8D | Type-74LS245 Integrated Circuit | 37-74LS245 | |
| 7M | Type-74LS86 Integrated Circuit | 37-74LS86 | |
| 7N | Type-74LS20 Integrated Circuit | 37-74LS20 | |
| 8A | Type-74LS74 integrated Circuit | 37-74LS74 | |
| 8F | Type-04 Custom Integrated Circuit | 137191-001 | |
| 8H | Type-74LS158 Integrated Circuit | 137203-001 | |
| 8J | Type-74LS257 Integrated Circuit | 37-74LS257 | |
| 8K | Type-74LS257 Integrated Circuit | 37-74LS257 | |
| 8N-11N | 10 W Audio Power Amplifier Integrated Circuit | 137215-001 | |
| 9B-11B | Type-74LS283 Integrated Circuit | 137204-001 | |
| 9C | Type-09 Custom Integrated Circuit | 137282-001 | |
| 9D-11D | Type-74LS174 Integrated Circuit | 37-74LS174 | |
| OF | Type-74LS32 Integrated Circuit | 37-74LS32 | |
| 9H, 10H | Type-74LS157 Integrated Circuit | 37-74LS157 | |
| QJ | Type-74LS298 Integrated Circuit | 137201-001 | |
| 9K | Type-74LS368 Integrated Circuit | 137168-001 | |
| 10€, 11C | Type-74LS367 Integrated Circuit | 37-TALS367 | |
| 10E | Type-74LS08 Integrated Circuit | 37-74LS08 | |
| 10F | Type-74S04 Integrated Circuit | 37-74S04 | |
| 10J | ‘Type-74LS157 Integrated Circuit | 37-74LS157 | |
| 10K | Type-74LS174 Integrated Circuit | S7-TALS174 | |
| NE | Type-74LS368 Integrated Circuit | 137168-001 | |
| iF | Type-74S163 Integrated Circuit | Acceptable substitutes are part nos. | 137274-001 |
137287-001 & 137287-002
| 11H | Type-74S00 Integrated Circuit | 37-74S00 |
| Wd | Type-74LS20 Integrated Circuit | 37-74LS20 |
| 11K | Type-74LS74 Integrated Circuit | 37-T4LS74 |
| 12B | Type-74LS138 Integrated Circuit | 137177-001 |
| 12F | Type-74S04 Integrated Circuit | 37-74S04 |
Diode
| b1 | Type-1N4735A, 6.2 V, 1 W Zener Diode | 131009-001 |
Random-Access Memories
| 7B, 8B | Static-2048 x 8 Random-Access Memory (200 ns) | Acceptable substitute is | 137198-001 |
part no. 137211-001 (150 ns)
| 7C, 8C | Static-2048 x 8 Random-Access Memory (200 ns) | Acceptable substitute is | 137198-001 |
partno. 137211-001 (150 ns)
| 4F-7F | Static-1024 x 4 Random-Access Memory (200 ns) | 90-7036 |
| 4H-7H | Static-1024 x 4 Random-Access Memory (200 ns) | 90-7036 |
| A | Static-1024 x 4 Random-Access Memory (55 ns) | 137199-001 |
| 7K | Static-1024 x 4 Random-Access Memory (55 ns) | 137199-001 |
-® New to Pole Position II.
3-32 (Continued on next page)
CO-218-12 Parts Lists
Pole Position II Namco Video Printed-Circuit Board Assembly Parts List, continued
| Designator | Description | Part No. |
Programmable Read-Only Memories
| 1A | Electrically Programmable Read-Only Memory 32 | 136014-134 | |
| 1E | os | Electrically Programmable Read-Only Memory 29 | 136014-173 |
| 1F | os | Electrically Programmable Read-Only Memory 28 | 136014-172 |
| aL | Electrically Programmable Read-Only Memory 27 | 136014-231 | |
| 1M | on | Electrically Programmable Read-Only Memory 26 | 136014-171 |
| 1N | os | Electrically Programmable Read-Only Memory 25 | 136014-170 |
| 2A | Electrically Programmable Read-Only Memory 31 | 136014-128 | |
| 2H | so | Programmable Read-Only Memory 10 | 136014-189 |
| 2M | ce) | Programmable Read-Only Memory 12 | 136014-174 |
| 2N | os | Programmable Read-Only Memory 12 | 136014-175, |
| 3A | Electrically Programmable Read-Only Memory 30 | 136014-127 | |
| 3c | os | Programmable Read-Only Memory 12 | 136014-191 |
| 3M | eo | Electrically Programmable Read-Only Memory 22 | 136014-169 |
| 3N | - | Electrically Programmable Read-Only Memory 21 | 136014-168, |
| 4D | os | Programmable Read-Only Memory 11 | 136014-190 |
| 4M | os | Electrically Programmable Read-Only Memory 20 | 136014-167 |
| 4N | os | Electrically Programmable Read-Only Memory 19 | 136014166 |
| 5M | Electrically Programmable Read-Only Memory 18 | 136014-120 | |
| 5N | Electrically Programmable Read-Only Memory 17 | 136014-119. | |
| 6M | os | Programmable Read-Only Memory 6 | 136014-192 |
| 8E | Programmable Read-Only Memory 13 | 136014-135 | |
| BL | oe | Programmable Read-Only Memory 7 | 136014-186 |
| 9A | Programmable Read-Only Memory 15 | 136014-142 | |
| 9E | Programmable Read-Only Memory 14 | 136014-136 | |
| 9L | oo | Programmable Read-Only Memory 8 | 136014-187 |
| 10A | Programmable Read-Only Memory 16 | 136014-143 | |
| 10L, | sn | Programmable Read-Only Memory 9 | 136014-188 |
| TA | Programmable Read-Only Memory 17 | 136014-144 |
Resistors
| Ri-R8 | 1kQ, +5%, Ys W Resistor | 110000-102 |
| RO | 3300, +5%, Y% W Resistor | 110000-331 |
| R10 | 3300, +5%, % W Resistor | 110000-331 |
| R11-R15 | 1kQ, +5%, Ys W Resistor | 110000-102 |
| RI6 | 2200, +5%, V4 W Resistor | 110000-221 |
| R17 | 470.0, +5%, % W Resistor | 110000-471 |
| R18 | 1kQ, +5%, % W Resistor | 110000-102 |
| R19 | 2.2kQ, +5%, 4 W Resistor | 110000-222 |
| R20 | 2200, +5%, v4 W Resistor | 110000-221 |
| R21 | 4702, +5%, ¥s W Resistor | 110000-471 |
| R22 | 1kQ, +5%, % W Resistor | 110000-102 |
| R23 | 2.2k0, +5%, V4 W Resistor | 110000-222 |
@5 New to Pole Position Il.
(Continued on next page)
3-33
Parts Lists CO-218-12
Pole Position II Namco Video Printed-Circuit Board Assembly Parts List, continued
| Designator | Description | Part No. |
| R24 | 2202, +5%, Ya W Resistor | 110000-221 |
| R25 | 470.0, +5%, Ya W Resistor | 110000-471 |
| R26 | 1kQ, +5%, % W Resistor | 110000-102 |
| R27 | 2.2kQ, +5%, v4 W Resistor | 110000-222 |
| R28 | 1kQ, +5%, % W Resistor | 110000-102 |
| Reg | 1k@ Horizontal Potentiometer | 119003-102 |
| R30 | 1kQ, +5%, % W Resistor | 110000-102 |
| R31 | 1 kQ Horizontal Potentiometer | 119003-102 |
| R32 | 1k@Q Horizontal Potentiometer | 119003-102 |
| R33, R34 | 1kQ, +5%, Ys W Resistor | 110000-102 |
| R35 | 1k@ Horizontal Potentiometer | 119003-102 |
| R36 | 1kQ, +5%, % W Resistor | 110000-102 |
| R37 | 100 2, +5%, 4 W Resistor | 110000-101 |
| R40 | 1kQ, +5%, Y% W Resistor | 110000-102 |
| RM1-RM3 | 1kQ, 4-Station, 5-Pin, Single-Inline-Package Resistor Network | 118001-102 |
| RM10 | 1kQ, 4-Station, 5-Pin, Single-Inline-Package-Resistor Network | 118001-102 |
| RM11, RM12 | 470 O, 8-Station, 9-Pin, Single-Inline-Package Resistor Network | 118002-471 |
| RM13, RM14 | 1kQ, 4-Station, 5-Pin, Single-Inline-Package-Resistor Network | 118001-102 |
| RM4 | 4.7 kQ, 8-Station, 9-Pin, Single-Inline-Package Resistor Network | 118002-472 |
| RM5-RMS- | 2.2 kQ, 8-Station, 9-Pin, Single-Inline-Package Resistor Network | 118002-222 |
| VRIVR4 | 1kQ, +20% Horizontal Trimming Potentiometer | 119003-102 |
Sockets
| 1A | 24-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C24 | |
| 1B | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C28 | |
| 1E | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C28 | |
| 1F | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C28 | |
| 1H | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C28 | |
| aL | 24-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C24 | |
| 1M-5M | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C28 | |
| 1N-6N | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C28 | |
| 2A, 3A | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C28 | |
| 2H | 16-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C16 | |
| 2M | os | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C28 |
| 2N | ao | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C28 |
| 3c | 18-Contact Medium-insertion-Force Integrated Circuit Socket | 79-42C18 | |
| 3D | 18-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C18 | |
| 3E | 18-Contact Medium-Iinsertion-Force Integrated Circuit Socket | 79-42C18 | |
| 4D | 16-Contact Medium-Iinsertion-Force Integrated Circuit Socket | 79-42C16 | |
| 6M | 18-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42018 | |
| 7A | 28-Contact Medium-insertion-Force Integrated Circuit Socket | 79-4228 | |
| 8c | os | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C28 |
| 8F | 28-Contact Medium-insertion-Force Integrated Circuit Socket | 79-42C28 | |
| 8L-10L | 16-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C16 | |
| 9C | 24-Contact Medium-Iinsertion-Force Integrated Circuit Socket | 79-42C24 |
@9 New to Pole Position Ii.
(Continued on next page)
3-34
CO-218-12 Parts Lists
Pole Position II Namco Video Printed-Circuit Board Assembly Parts List, continued
| Designator | Description | Part No. |
Miscellaneous
| J | 60-Pin Connector | 179157-060 | |
| J2 | 3-Pin Power Connector | 179156-003 | |
| x1 | 24,576 MHz Crystal | Acceptable substitute is part no. 144004-002 | 144004-003 |
Test Points Acceptable substitute is part no. 020670-01 179051-001
Heat Sink 039566-01 Printed-Circuit Board Brace 039562-01 Printed-Circuit Board Interconnector Cable Assy. 171036-001
Metric Screws and Washers #M3 x 6mm Pan-Head Stainless Steel Machine Screw 176017-006 #M3 x 8mm Pan-Head Stainless Steel Machine Screw 176017-008 #M3 x 10mm Pan-Head Stainless Stee! Machine Screw 176017-010 #M3 Stainless Steel Flat Washer 175005-002
#M3 Stainless Steel Split-Lock Washer 175006-002 #M3 Metric Stainless Steel Hex Nut 177005-002
3-35
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
4 Schematic Changes
Schematic documentation for Pole Position is shipped with your game. If your game has an Atari PCB game set, this information is contained in SP-218. If your game has aNamcoPCB game set, this information is contained in SP-219. To convert these schematic packages so they support Pole Position Il, delete the type numbers of the integrated circuits listed in Tables 4-1 and 4-2.
Schematic Changes
Table 4-1 SP-218 Schematic Package Changes CO-218-12
Circuit Name IC Location Page in SP-218
| Microprocessor A | 4E, 4D, 3E, 3D | Sheet 5A |
| Microprocessor B | 4L, 4K, 3L, 3K | Sheet 5B |
| Sound Microprocessor | 7H, 7F | Sheet 6A |
| Speech Processor and Memory | 9C, 9A, 8C | Sheet 9A |
| Vertical Position Modifiers | 2D, 2C, 2B | Sheet 118 |
| Roadway Memory and Adders | 2M, 2N, 2b | Sheet 12B |
| Alphanumeric and Background PROM | 5K, 4L, 6N, 7N | Sheet 134 |
| Match Circuit | 11N | Sheet 14A |
Picture Memory (Signs and Cars) 12J, 13J, 12K, 13K, 12L, 73L, 12M, 13M, 12N, 13N Sheet 14B
Table 4-2 SP-219 Schematic Package Changes
Circuit Name IC Location Page in SP-219
| Microprocessor A | 8L, 7L, 8M, 7M | Sheet 5A |
| Sound Microprocessor | 6H, 5H | Sheet 6A |
| Speech Processor and Memory | 2, 1E, 2F, 1F | Sheet 9A |
| Roadway Memory and Adders | 2A, 1A, 3A | Sheet 12B |
| Alphanumeric and Background PROM | 1E, 1F | Sheet 134A |
Picture Memory (Signs and Cars) 5M, 5N, 4M, 4N, 3M, 3N, 2M, 2N, 1M, 1N Sheet 148
CO-218-12 1st printing
YOUR COMMENTS, PLEASE!
Your comments will assist Atari in improving our publications. The comments are an important part of preparing for revisions of game manuals. Please write in the space below. No postage stamp is necessary if mailed in the U.S.A
If you have any technical questions about certain ATARI games products, or are requesting additional publications, we will immediately forward your note to the appropriate person.
Page: Comments:
Fill in if you wish a reply:
Name_.
Firm CO Distributor
Address. (Le Operator
City State Zip CG Other
Area Code Phone
First fold
No Postage Necessary st mailed in the United States
BUSINESS REPLY MAIL — FIRST CLASS PERMIT NO. 1004 SUNNYVALE. CA — POSTAGE WILL BE PAID BY ADDRESSEE ee
Atari, Inc. es
Attn: Field Service/Coin-Op Division P.O. Box 906 a 737 Sycamore Pe Milpitas, California 95035
a
Segond told TO
Wwol4 aBpe sty) edey
c0-218-12 1st printing
YOUR COMMENTS, PLEASE!
Your comments will assist Atari in improving our publications. The comments are an important part of preparing for revisioris of game manuals. Please write in the space below.
If you have any technical questions about certain ATAR! games products, or are requesting additional publications, we will immediately forward your note to the appropriate person.
Page: Comments:
Fill in if you wish a reply:
Name.
Firm © Distributor
Address. O Operator City Country C Other.
Phone: Country Code Local Number
First told
Attach Necessary Postage
Atari Ireland Limited Attn: Field Service/Coin-Op Division Tipperary Town, Ireland
‘wor eBpe sly edey
PN DE, TE TE EVE EO
Kit Warranty
Seller warrants that its electronic parts supplied in this kit are free from defects in material and workmanship under normal use and service for a period of ninety (90) days from date of shipment. None of the Seller's other products or parts thereof are warranted. Ifthe electronic parts supplied in this kit fail to conform to this warranty, Seller's sole liability shall be, at its option, to repair, replace, or credit Buyer's account for such electronic parts which are returned — to Seller during said warranty period, provided: PA | (a) Seller is promptly notified in writing upon discovery by Buyer that said products are defective;
- Such products are returned prepaid to Seller's plant; and (c} Seller's examination of said products discloses to Seller's satisfaction that such alleged defects existed and were not caused by accident, misuse, neglect, alteration, improper repair, installation, or improper testing Inno event shall Seller be liable for loss of profits, loss of use, incidental or consequential damages. Except for any express warranty set forth in a written contract between Seller and Buyer whichcontract supersedes the terms herein, this warranty is expressed in lieu of all other warranties expressed orimplied, including the implied warranties of merchantability and fitness for a particular purpose, and of ail other obligations or liabilities on the Sellers part, and it neither assumes nor authorizes any other person to assume for the Seller any other liabilities in connection with the sale of products by Seller.
The use of any non-Atari parts may void your warranty, according to the terms of the warranty. The use of any non-Atari parts may also adversely affect the safety of your game and cause injury to you and others. Be very cautious in using non-Atari-supplied components with our games, in order to ensure your safety. Atari distributors are independent, being privately owned and operated. In their judgment they may sell parts or accessories other than Atari parts or accessories. Atari cannot be responsible for the quality, suitability or safety of any non-Atari part or any modification including labor which is performed by such distributor.
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
Game Warranty
Seller warrants that its printed-circuit boards and parts thereon are free from defects in material and workmanship under normal use and service for a period of ninety (90) days from date of shipment. Seller warrants that its video displays (in games supplied with displays) are free from defects in material and workmanship under normal use and service for a period of thirty (30) days from date of shipment. None of the Seller's other products or parts thereof are warranted. If the products described in this manual fail to conform to this warranty, Seller’s sole liability shall be, at its option, to repair, replace, or credit Buyer's account for such products which are returned to Seller during said warranty period, provided:
- Seller is promptly notified in writing upon discovery by Buyer that said products are defective; (b)Such products are returned prepaid to Seller's plant; and (c)Seller’s examination of said products discloses to Seller's satisfaction that such alleged defects existed and were not caused by accident, misuse, neglect, alteration, improper repair, installation, or improper testing. In no event shall Seller be liable for loss of profits, loss of use, incidental or consequential damages. Except for any express warranty set forth in a written contract between Seller and Buyer which contract supersedes the terms herein, this warranty is expressed in lieu of all other warranties expressed or implied, including the implied warranties of merchantability and fitness for a particular purpose, and of all other obligations or liabilities on the Seller's part, and it neither assumes nor authorizes any other person to assume for the Seller any other liabilities in connection with the sale of products by Seller.
ES ES ES ES ES
The use of any non-Atari parts may void your warranty, according to the terms of the warranty. The use of any non-Atari parts may also adversely affect the safety of your game and cause injury to you and others. Be very cautious in using non-Atari-supplied components with our games, in order to insure your safety. Atari distributors are independent, being privately owned and operated. In their judgment they may sell parts or accessories other than Atari parts or accessories. Atari cannot be responsible for the quality, suitability or safety of any non-Atari part or any modification including labor which is performed by such distributor.
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.