CATHODE RAY TOMES

Blockade Owners Manual

Blockade (Gremlin, 1976) · Owner's Manual · 33 pages · 34 sections · original scan

Page 1

MANUFACTURED BY

PART NO. Cre ;

707-0001 min Industries, inc.

OWNERS MANUAL

Page 2

BLOCKADE

OPERATING INSTRUCTIONS

AND

SERVICE MANUAL

GREMLIN INDUSTRIES, INC. 8401 Aero Drive San Diego, CA. 92123

Page 3

TABLE OF CONTENTS

Introduction

Warranty ... 0... Uncrating and Inspection

BLOCKADE Description

System Description . . .

Maintenance... 1...

Maintenance Procedures

Schematics and Parts List Page

Page

Page

Page oan fF WB Page

Page 10

oe ee Page 11

Following Pages

Page 4

INTRODUCTION

BLOCKADE is an electronic game that makes extensive use of digital integrated circuitry and television monitor circuitry. This manual assumes the maintenance technician possesses a general knowledge of solid state circuitry, TTL digital integrated circuitry and T.V. monitor concepts. Any individual NOT knowledgeable in these area SHOULD NOT attempt repair of the electronic portion of this game. IT SHOULD BE NOTED THAT ANY ATTEMPT TO REPAIR THE GAME IN THE FIELD WITHOUT THE EXPRESS CONSENT OF THE FAC- TORY WILL IMMEDIATELY VOID THE WARRANTY! !

IMPORTANT NOTES:

NEVER

NEVER

DO NOT

ALWAYS

CORRESPONDENCE replace any components with anything other than exact replacement parts. (See Parts List located on Service Schematics.)

remove circuit boards/connections while power is on.

replace the fuse with anything other than the proper value. A blown fuse indicates an overload condition within the game. Replacing the fuse with a higher value can cause severe damage to internal components if an overload occurs.

consult the manual before attempting repairs.

regarding this game should be addressed to:

GREMLIN INDUSTRIES, INC. 8401 Aero Drive

San Diego, California 92123

(714) 277-8700

Page 5
NOTE

An important service note is posted in the BLOCKADE game and is repeated here for emphasis:

IF AT ANY TIME THE T.V. SCREEN SHOWS A MEANINGLESS DISPLAY OR THE GAME OTHERWISE MALFUNCTIONS, SIMPLY DROP A COIN INTO THE COIN MECHANISM, THIS SHOULD COR- RECT THE PROBLEM. IF NOT, THE GAME REQUIRES SERVICE.

The circuitry in BLOCKADE has been arranged so that the insertion of a quarter thru the coin mechanism will reset the restart in the system. This clears up temporary problems caused by power line disturbances, static, etc.

SERVICE TECHNICIAN NOTE:

The system reset circuitry described above requires that the coin counter is attached to the system. If there is a coin counter problem and no replacement is available, the game will function properly if a LOK Ohm resistor is connected across the coin counter input pins to the video logic board.

Page 6

WARRANTY WARRANTY/FACTORY SERVICE INFORMATION

BLOCKADE is under factory warranty (Parts and Labor) for the following time periods:

A. All electronic components/connectors for one (1) year except:

  • Transformers - 90 days.
  • Fuses/Lamps - No Warranty

This Warranty covers defects/failure under normal use.

Should an assembly become defective, contact your local distributor. Factory authorization to return the assembly will be issued with transportation charges prepaid. If decided upon by factory representative an advance replacement will be made.

The assembly will! be repaired and returned, transportation charges prepaid, if still in Warranty and no advance replacement made.

If the assembly is found to be damaged by misuse, improper attempts at repair, or abuse, it will be repaired and returned with transportation and repair charges billed.

Out of Warranty assemblies, if returned to the factory with transportation charges prepaid, will be repaired and returned with transportation and repair charges billed,

In the instance of a defect of an assembly manufactured by other than GREMLIN INDUSTRIES, INC., every effort will be made to assist the customer in obtaining satisfaction from the original manufacturer.

Page 7
NOTE: UNCRATING AND SET-UP INSTRUCTIONS

"BLOCKADE VIDEO GAME"

During the entire uncrating and setting up of this game, a continual inspection should be carried out for cabinet damage and/or any other damage to electronic and mechanical hardware.

The following steps should be taken in uncrating and setting up of this game: (See diagram Page 5.)

A. Remove all strapping (ref. 1)

B. Remove top lid of container (ref. 2)

c. Remove staples on vertical overlap portion of container before removing from cabinet. (ref, 3)

D. Before removing the four corner pads that are taped to cabinet, (ref. 4), carefully lay the cabinet on either of two sides and remove the skid bolts (ref. 5) and skid (ref. 6) and discard,

E. Remove keys (ref. 9) from packet and unlock coin door, then remove shipping screw (ref. 7) from inside of coin box and discard.

F. Use key (ref. 9) to unlock back panel. After panel has been removed, inspect all electrical and other hardware for damage.

G. If damage has occurred during shipment, the recipient should immediately file a Damage Claim with the carrier.

H. Power Specifications: AC, 100V-115V-230V, 50/60Hz, 130 W, 3-Wire Cord with safety interlock on the rear gameaccess door; NOTE - grounding is required,

Page 8

INSTRUCTIONS

BLOCKADE

UNCRATING

Page 9

1. BLOCKADE

GAME CONCEPT -

BLOCKADE is a two player game in which each player controls the direction of an arrow moving on the face of a video display, The perimeter of the display is a barrier, constructed of images which resemble blocks.

Each player utilizes a set of push button controls to change the direction of his moving arrow. As it moves, the arrow leaves a "trail" of block images, which form a continuous wall or barrier.

Anytime a player's arrow collides with a wall, there is an audible explosion and accompanying flashing symbol at the point of impact. A point is awarded to your opponent when your arrow enters an already occupied space (i.e.):

. the block barrier created by either player . the perimeter walls . the opponent's arrow «reverse direction of your own arrow PwWNH

After a pre-set number of crashes by either player, the game ends. Example: If the game were set to end after five crashes, the first player to crash five times loses the game.

OPERATION -

The arrows move alternately at a fixed rate, approximately two times per second. To change direction of his arrow, a player momentarily presses the push button required for a left or right turn relative to his direction of travel, The arrow will move in the new direction until changed again. A player's reaction time is important as turns must be made at precise moments during the play.

As the arrows move, a series of tones are audible. Every direction for each arrow generates a different pitch (eight in all). The result is an audible change whenever either player makes a turn.

After each collision, the players' scores are briefly displayed. If the game has not been won, all obstacles except the perimeter walls are cleared, and the next segment of the game begins.

Page 10

Whenever BLOCKADE is not being played, an "advertisement sequence is initiated. The game plays itself to attract attention. To avoid patron confusion, the words "Game Over" appear while the advertising game is being played, and during a forty second delay thereafter. Following the delay, the advertising sequence repeats.

E-Z Adjust Control Panel - BLOCKADE has three adjustments, all of which are located on the back of the coin door. These three controls are:

  • VOLUME CONTROL -

Set to desired volume for boom and tones during the game. This also effects advertising boom volume if boom switch is "ON",

  • BOOM SWITCH -

Switch to "ON" position if boom is desired during advertising.

  • GAME END SWITCH -

Switch to desired game ending score. (3-4-5- or 6)

Page 11

fa INO naeaneal

SYSTEM DESCRIPTION

SEE SYSTEM BLOCK DIAGRAM (Fig. 1)

MICROPROCESSOR -

The game microprocessor is a Model 8080A and it functions as the Central Processing Unit (CPU) inthe system. The CPU (1) is synchronized by a clock circuit which provides frequencies required by the CPU and the Video Timing Logic (14).

Address Bus (4) selects the memory addresses to be accessed by the CPU. It is routed to three subsystems:

  • Read Write Memory (6): A random Access Memory Ran) used to form a first in/last out (stack) memory. Used to perform subroutine calls and returns, also used for temporary data storage during program execution,
  • ReadOnly Memory (Rom) (7): Stores program instructions for the CPU.
  • Address Multiplexer (8): Selects either CPU addresses or addresses from the Video Timing Logic, Used to address the Video Refresh Memory (9).

Data Bus (5) carries data to and from the CPU. It receives data from Read Write Memory,Read Only Memory, Video Refresh Memory and Input Ports (12). The Bus transmits data to Read Write Memory, Output Ports and Video Refresh Memory. The Input Ports accept player control data (19). The Output Port (13) initiates sound control and activates any external logic and indicators needed by the game.

Timing and Control Logic (11) generates synchronizing signals to keep system operation synchronized to the CPU. It controls:

1, Memory Read

  • Memory Write
  • Input Port Read
  • Output Port Write

~8-

Page 12

VIDEO TIMING

SYNC AND

BLANKING

yiveo = iz

COMBINER

CPU MEMORY

ADDRESS

REFRESH Lee POA BS CR INE ST

PLAYER MEMR CONTROLS SOUNDS INDICATORS

MEM W INPUT STROBE OUTPUT STROBE SYSTEM BLOCK DIAGRAM

FIG 1 +V

Page 13

The remaining elements in Figure 1 convert (CPU) system information into a video display format. The T.V. monitor (18) uses a standard 525 scan line system.

Video Refresh Memory (9) stores information from the CPU which is read out as the CRT beam sweeps across the screen. It is addressed from two sources as controlled by Address Multiplexer (8). During vertical sweep retrace of the CRT, the Video Refresh Memory is addressed by the CPU so information can be updated. During scan time, Video Refresh Memory is addressed by Video Timing Logic (14), Refresh Memory Control (10) insures that address demands from Video Timing Logic and the CPU never occur simultaneously.

Character Generator Memory (15) provides a means for Video Reftesh Memory to select 64 dots for each 8 word access. Each image, on the display, will have the dimensions of 8.dots high, and 8 dots wide. Shift’ register (16) develops this into a video signal. (see Figure 2)

A Tone Generator is driven by Output Ports (13). The CPU controls the frequency of the tone by loading a number (0-255) into the Output Ports (13). A direction change by a player will cause the CPU to load a different number into the Output Port, changing the tone. (see Figure 3)

Page 14

MEMORY INPUT Dara

FROM MICROPROCESSOR

CATA BUS

AO OUYOU TOUT foUTIOUT} OUT IO at Ne om + MO ro

VIDEO

REFRESH

MEMORY

ADDRESS - FROM AQDRESS MULTIPLEXOR

1024 x 6 A3 A4 CHARACTER AS GENERATOR Ac MEMORY Aq 256 x8 EIGHT OUTPUTS TO SHIFT REGISTER

FIG 2

Page 15

FROM MICROPROCESOR

/ SYSTEM \

OUTPUT

STROBE

LATCH

(9.7475)

(e.9.7475) A 6 Cc Dd,

PRESET COUNTER

7 > @.g-. 74163) tp NPRESET COUNTE OUTPUT

b 9.74163) TONE GENERATOR FIG 2

Page 16

MAINTENANCE

NOTE: IF AT ANY TIME THE T.V. SCREEN SHOWS A MEANINGLESS DISPLAY OR THE GAME OTHERWISE MALFUNCTIONS, DROP A COIN IN THE COIN MECHANISM. THIS SHOULD CORRECT THE PROBLEM, IF NOT, THE GAME REQUIRES SERVICE.

FACTORY ASSISTANCE;

TECHNICAL HELP 1S AVAILABLE FROM THE GREMLIN FACTORY, IFA

PROBLEM OCCURS WHICH CANNOT BE EASILY RESOLVED BY YOUR DISTRIB-

UTOR, A PHONE CALL OR LETTER TO THE FACTORY WILL BRING ATTENTION TO YOUR PROBLEM BY A TRAINED REPRESENTATIVE,

EQUIPMENT:

« Oscilliscope - 50 mhz or wider band width

. DVM (Digital Volt Meter)

OHM Meter

Logic Probe

Solder Station - 75 Watt or less

Jumpers NOU fF WN « Replacement parts including game programs:

1024 x 4 prom 316-0004 and 316-0003

This is a recommended list for anyone attempting to service BLOCKADE,

Page 17

MAINTENANCE PROCEDURES

BLOCKADE POWER SUPPLY MALFUNCTION:

  • Remove Output Connectors
  • Initial Tests: (GND lead to C-18 negative terminal located off board.)

a.

b.

c.

d.

e.

f,

9. +9v at "+" of C-18

+19v at C-6 (4700 mfd)

-19v at C-5 (4700 mfd)

-12v at pin 11

+12v at pin 12

+5v at pins 18-20

zero v (GND) at pins 14-16

  • If adjustments are required, attach meter ground to pins 14, 15 or 16 or equivalent local ground and:

+5v adjust - input lead to pins 18, 19, 20 and adjust R-9 for +5.0 to +5.1 VDC

+12v adjust - input lead to pin 12 and adjust R-8 for 11.5 to-12.1 VDC

-12v adjust ~ input lead to pin 11 and adjust R-10 for -11.1 to -12.1 VDC

  • If initial test is good, attach output connectors to Video Logic Board. Repeat Step 2.

a. If readings differ from those previously taken, a loading problem exists on the Video Logic Board.

No -L2VDC or 5VDC-on the Video Logic Board: (Power Supply Norma!)

Video Logic Board Schematic (WEBS)(SH. 2). CHECK U-65, C-29 for open/short. CHECK R-40, C-12, D-2(VLBS) (SH. 1).

-ll-

Page 18

No +12VDC at CPU: (Power Supply Normal) WLBS)(SH. 2), CHECK U-65, C-28. (VLBS){SH. 1). CHECK C-23, C-25. No 91, @2 CLOCKS: (Ref. Fig. 4A) WLBS),(SH. 1). CHECK U-32 pins 1 and 3 for 20.79MHZ, CHECK U-31 pins 14, 13, 12 and 11 for 150 nsec sinewave. CHECK U-17 pins 1, 3,4, and 10, CHECK latch network U-18 and U-8. CHECK high voltage outputs of U-30 pins 3 and 6. If not present, remove driver transistor. Should U-30 now output, replace driver transistor, if still not present reolace U-30. U-45 could load down 91 clock. No Coin Start:

(VLBS)(SH. 1) CHECK output U-9 pin 6. If signal not present, lift U-10 pin 5. Should signal return, replace U-10. If still not present, check output of U-8 pin 3. CHECK D-8 pull up diode and C-18. CHECK U-14. U-32 could be shorting signal to Q, and Q,.

No Coin Meter Action: (VLBS)(SH. 1). Signal from U-8 pin 11 feeds current limiter R-27 to Q,-

Saturated Q 4 turns on high current transistor Q, . Either Q 4 of Qa, faulty,

will inhibit meter.

No Player Control: (VLBS)(SH. 1). Input accepted through U-12 and U-13 via data lines when strobe IND2 signal is generated through U-18 from U-45 and U-51 (status latch). CHECK U-18 pin 11, U-45 pin 8, U-45 pin 11, U-51 pin 10 for strobe pulse. No Game Time Select:

(VLBS)(SH. 1). Input accepted through U-10 and U-11 via data lines when strobe IND1 signal is generated through U-18 from U-45 and U-51. CHECK U-18 pin 3, U-45 pin 8, U-45 pin 11, U-51 pin 10 for strobe pulse. Meaningless Display on Screen: (Inserting coin does not correct problem) There are two probable areas;

  • A program malfunction

a. Check ROM sockets, U-2 and U-3

Page 19
  • A data transfer malfunction

a. Test the CPU Data Bus by ensuring proper voltage levels. Pullup resistors are used to make memory outputs compatible with the 8080A. High State Logic on the Data Bus should be 3.3v minimum. For involved problems in this area contact GREMLIN. INDUSTRIES, Characters on Screen not correct: (Wrong image behaves normally) (VLBS\SH. 2). Use character generator code table to isolate possible: bad RAM (U-38; U-39; U-40; U-41, or U-42), . Also probable are U-22. U-23 (data buffers), U-24, U-25, U-26 (multiplexers), U-29 and U-43, U-49 (shift register). No Video: (Ref. Fig. 4B, 4C, 4D) (VLBSXSH, 2), CHECK U-54, U-53 circuitry for H reset. U-52 pin 1, clock for horiz. scan. U-55, U-58 provides timing for vert. scan. U-56 provides for vert. blanking. Bad Video:

(WLBS)(Sh. 2). Bad video could be vertical roll or horizontal sliding. CHECK U-55 pin 12 and U-56 pin 4 of horizontal or vertical generators. CHECK U-63 pins 12 and 13 for vertical and horizontal blanking. U-64 develops sync pulses. Monitor Mal function: Refer to Motorola Service Manual (File VP 12), This manual included with BLOCKADE schematics.

Audio Tones; Sour/None: WLBSXSH. 2). U-68, U-61, U-62, U-66, U-67, U-60 comprise tone

generator. Amplifier on Power Supply Board (U-4, a Q3, aX, Q,). Could

also be problem area. Boom; Sour/None: (VLBSXSH. 1, Sh. 2). D-6, Qi9, Qg, Qyz,U U-5, Q, Q,, Generates Boom.

Amplifier section on Power Supply Board u-4, Q,, ay. Qe Q), also probable,

Page 20

)

fc)

°

°

fs]

° con 2)

CHARACTER CODE TABLE

U 404] 42

fe)

fo)

ft)

fe}

fe] fe}

fe}

°

° °

°

o oO = oO - 9 '

° PeUOSHESOYTE TYR EH U 38 39 40 41 42

o oo 8 O90

°o

GAME OVER

[e}

° Cnt ow BWR —- OC

(BLANK)

1b

nT

JE

SR

Page 21

v224 V262 H264 H330 ay IV

H BLANK ov © VBLANK [ Loy

H RESET 1330 =z V262

T ov V RESET al

H272 H288 T 02

ai Howe _[] € V238 248 y

ov V SYNC ee el

OV ©) CONNECTOR PIN 38 2 op / AY nF n

WITH CONNECTOR OFF OY fo

4 INVERTED HORZ. DURING Y BLANK

FIG. 4

Page 22

BLOCKADE PARTS LIST

DESCRIPTION PART NUMBER QTY, USED

ANCHOR WASHER280-00281
ASSY, CONTROL BLOCK807-00071
CABLE TIE280-u09510
CONN, CRIMP COINBOX211-00016
CONN, CRIMP LOCK211-000514
CONN, FEM 4 PIN BLK212-00052
CONN, FSM 10 PIN212-00161
CONN, KEY, POLARIZING211-00074
CONN, SPADE LUG 1/4"211-00192
DECAL, VOLUME CONTROL420-00311
KNOB, VOLUME CONTROL240-00011
POT, 10K475-00071
SWITCH BRACKET250-00311

SWITCH, SINGLE POLE, 4P@S, 511-0003 1

SWITCH, SLIDE, SPOT518-00141
ASSY, JUMPER HARNESS807-0006i
CONN, CRIMP LOCK211-000516
CONN, FEM 10 PIN212-00162
CONN, KEY, POLARIZING211-00074
ASSY, JUNCTION BOX807-00091
BUSHING, STRESS/RELIEF280-00072
CONN, QUICK 1/4" FEM211-00172
CONN, QUICK 3/16" FEM211-00224
CONN, SPADE LUG 1/4"211-001914
CORD, LINE, 3 COND.600-00011
FUSE, 2 AMP. 250v SB514-00011
HOLDER, FUSE514-00051
JUNCTION BOX140-00161
JUNCTION BOX COVER140-00171
SWITCH, SPDT CHERRY510-00131
TERMINAL STRIP 6 POS.280-00111
TERMINAL STRIP: MARKER280-00171
ASSY, MONITOR HARNESS807-00051
CONN, CRIMP LOCK211-00052
CONN, FEM 4 PIN BLK212-00051
CONN, KEY, POLARIZING211-00072
CONN, PINCRIMP, FEM211-00265
CONN, SPADE LUG 1/4"211-00193
Page 23

BLOCKADE PARTS LIST (Cont'd.)

DESCRIPTION

ASSY, OPERATOR SWITCH CABLE TIE CONN, CRIMP LOCK CONN, FEM 10 PIN CONN, KEY POLARIZING CONN, QUICK, 1/4" FEM CONN, SPADE LUG 1/4" SWITCH, P/BUTTON, UNIMAX SWITCH, PLATE ASSY, POWER INTERRUPT ASSY, POWER SUPPLY ASSY, SPEAKER CABLE CONN, CRIMP LOCK CONN, FEM 4 PIN BLK CONN, KEY, POLARIZING CONN, QUICK 3/16" FEM ASSY, VIDEO LOGIC B/A BEZEL FRAME CABINET B/A CABINET FEET CASH BOX CASH BOX, LOCKING ASSY CLIP, WIRE HOLD DOWN COIN COUNTER ASSY CONN, CRIMP LOCK CONN, FEM 10 PIN CONN, KEY, POLARIZING COUNTER, DIGITAL CORNER STRIP DECAL, BLOCKADE DECAL, CAUTION 115V DECAL, IMPORTANT NOTE DECAL, RE-CYCLE DECAL, SERIAL NUMBER. DECAL, SERIAL NUMBER, SMALL DECAL, SERVICE DRAWINGS, BLOCKADE DUAL COIN MECHANISM LAMP, FLUORESCENT, 18" LAMP’, FLUORESCENT, 18", (FIXTURE) LATCH, LOCK B/A PART NUMBER

807-0004 280-0005 211-0005 212-0016 211-0007 211-0017 211-0019 510-0012 250-0029 807-0012 807-0003 807-0010 211-0005 212-0005 211-0007 211-0022 807-0001 250-0032 140-0014 280-0030 220-0012 252-0014 280-0004 807-0011 211-0005 212-0016 211-0007 220-0008 420-0037 420-0032 420-0030 420-0038 420-0040 420-0028 420-0041 420-0029 420-0042 220-0010 390-0011 390-0012

220-0015 QTY, USED

i

ray BREE EPH BP ENE EP BE PENH UEP EP BEE ENN ENE EE NONDHHE OOH

e

Page 24

BLOCKADE PARTS LIST (Contd.)

DESCRIPTION

LOCK, PANEL MASK, SHADOW CABINET MONITOR SCREEN NUT, WIRE PANEL, DISPLAY UPPER PANEL, FRONT SWITCH PLATE, LOCK STRIKE SPEAKER COVER 6x9 SPEAKER, GAME SPRING, RETAINER SWITCH, LIP SWITCH, SLAM W/PLATE TOP COVER VIDEO MONITOR 19" WRAP AROUND SIDE PART NUMBER

320-0009 253-0014 253-0012 280-0010 253-0013 250-0030 250-0033 130-0002 130-0001 250-0034 250-0048 510-0016 420-0035 200-0002 420-0034 QTY. USED

BER EPP HEP PEEP ENP ee

Page 25

TENSIONS [owen SEcninon

~ SET /VSIDE SURFACE OF MOUNTING BRACKET Fs" ~ COIN MECHAIV/SM FROM DOOR FRAME L/P DOOR “f ERAME

  • se \_poae FRAME L/P

WEW LOOKING DOWN ON DOOR ERANE =~ DETAIL A

| | TEP 3, SECURE BRACKET 7O SHELF WITH (8) */0 x BELONG WO00D SCREWS

| —- CASH BOX MOUNTING BRACKET FUN 252-00/4

STEP 1. 1 £$PPLY GLUE TO ALL BOTTOM EDGES OF BRACKET

EX/STING BLOCKING ~o FOR CASH BOX, DO WOT a REMOVE Ne STEP 2: SY

SET FRONT EDGE

OF BRACKET AGHNEST) | BACK S/DE OF LE ome Ee PANEL TO DIMENS/ON MLSS | eclithene —__ naa SHOWN IN DETAIL A's, a : YEW LOOKING AT FROVT OF CAB, ABOVE BLOCKADE Gremalin Ineustries ms. “ 7 MOUNTING BRACKET |A ROR eoy hove v9 /NSTALLATION I CASH BOX RT TE | SERVICE NOTE*5

Page 26

CASH BOX

STEP 1; PLACE LID /N POSITION SHOWN OVER CASH BOX AND PUSH DOWN /N DIRECTION OF ARROW STEP 2, LOWER LY INTO CASH BOX REVISIONS DESCRIPTION

LOCK PLATE

MOUNTING ——~" BRACKET

STEP 3. SLIDE LID iN DIRECT/ON OF ARROW AS FAR BACK AS POSSIBLE STEP 4. SET CASH BOX /N7O IAKING MOUNTING BRACKET 7S INTO SURE LOCK PLATE F/ SLOT /N CASH BOX LID.

‘NOMENCLATURE OR DESCRIPTION, ‘PART OR IDENTIFYING NO. PARTS List TONLESS OTHERWISE SPECIFIED DIMENSIONS ARE. IN INCHES OLERANCES ARE: WOM SORTRET NO. BLOCKADE Gremlin Industries, Inc. Sam Dioge, California 92095 CASH BOx OPERATION

BRAIN WO SERVICE NOTE *5 [sneer 2 or 2 (CODE TENT WO]

Page 27

REVISIONS. DESCRIPTION

Ri IK Q2 2N4403 TRESS OERNINE SPESTIED [CONTRACT FO” PREERONS i THEME GREMLIN INDUSTRIES INC. Fractons otc avates [renova 240) AERO DR. SAN DIEGO,CA.92123 hah SCHEMATIC — POWER INTERRUPT ‘CODE IDENT NO, [DRAWING NO. aie 807-O0!2

APPLICATION

cag 4 3 2 1 170-0073 F.C, BOARD tf

= 212 -OO17 CONN FEMALE JOPIN RT ANGLE| ‘FB2-00/4_| TRANSISTOR 2N4401 Ghgs 482-0006 | TRANSISTOR 2N440>5 gz 481-0008 DIODE ZENER IN 5231 Di + f 471-OF74 RES. 470K OHM !172W 5% R7 ot 471-0333 RES. 33K OHM 2W 5% | Ro 47/-O104 | _RES- 100K OHM _1/2W_ 5% R4,R5 471-0102 RES. IK OHM /72 W 5% | RI-R3,RB-RIO 3 152-0002 CAP. F. .22M_100V CI ch [a z- - TC 8

2/2 150 - 00/6 CAP. E. IM lov e2,¢3 tl2 314- 000i 1 TIMER NESSS Ui, Ue

TTEM| ong Pan OF NOMENCLATURE Mon| a0] (ert | ioen4iFrINe wo, OR eSCRITTON PARTS LIST tein ae Srenee | [ONTPACT No GREMLIN INDUSTRIES INC. FRACTIONS DECALS ANGLES. B40! AERO DR. SAN DIEGO, CA. 72123

= elie = APPROVALS DATE A a pear Wegramnge e/a POWER INTERRUPT ASSY A ae — PARTS OVERLAY no BE] CODE TOERT WO ORAS FO ——| Cc 807-0012

Meet AaeY | vse On "APPLICATION BO NOT SCALE DRAWING scale NONET sneer For?) Ouarras 4 3 t 2 1

Page 28

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 29

Dg _MDA_ 3500 REV B PER ECN G3 WIE 2hs7 LAY 120 V { 100 V

ov

560-0003 A NOT ON P.C. BOARD

INS231

LAST C NO. USED C19 LAST ONO. USED DO LAST Q NO. USED Q10 LAST R NO. USED R 33 L LAST U NO. USED U 4

GREMLIN INDUSTRIES INC

8401 AERO DR. SAN DIEGO, CA. af REVISIONS Tce SCHEMATIC BLOCKADE PWR. SUPPLY feRecwED

Dirconden no toeae SCALE DRAWING NO, 807-000

Page 30

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 31

Omit Ru REVISIONS Zone] ite DESCRIPTION : pare | PA EEN oS Pe EL

‘CONN, MALE 4 PIN CONN. MALE 1D PIN a bec BOARD = WSTOR Tip 23 = ante R TIP is 7 407-0018 _{ xisToR TIP 110 439-0014] X STOR 2N4401 262-0006 | XiSTOR 2NSSOS =

ABI = 0006DISSE _INSIS OR INATSSmi

431 9008 ODE ZENER INSZal 4a1= 0004 | DIODE MR 50! T= 000: Bape Bye Soy

151 = 000:if a oTa
1Sr=CER. “05 MI BOYB
150 = 0019£M_25.V
151 = 0}2=

Tigi = ogiz M Soy

[150 0004MYfay

415 jo04 | Por TRIMMER

475-9005 | Pot.2 KTRIMMESI~
2T3- 00R}es.OHM 5 Wo SY712
arr = O01BES,__100 _OHM_@ Wf=pe
ATZ-00G —_} RES.[OHMWwW.~1S
R33L471 = 9194 | RES. 109K OHM a W.77q.
[p47i= 9332 | RES. 3.3K OHW ia w7eS
Ria 32147-019RES. 10h OHM 1g. WFs)
RoRie RIB‘S| a7i= 0182RES. 5K OHM V2 WS

Rp Ras Fi ai, - 027s PRES, 27K HM a

RsT-47i- 0822Res. 6.2K OHM A W SY
Race Res | a7l- 9102[ResK OWM 2 W 5%

RR RES. iq K OHM 12 W

IDsTE_oMT=

owas MT@1E} == ITEM NO. Ed I PARTS UST TORCESS OTHERWISE SPECIFIED DaMENSIONS. ARE, IN INCHES [TOLERANCES ARE: GREMLIN INDUSTRIPS INS 5401 AERO DR. SAN DIEGO, GA. 92123

= = Som ATER

FRSA

ROT ASST USED ON APPLICATION, 1DO_NOT SCALE DRAWING POWER SUSPLY/AM2 BOARA|A BLOCKADE PARTS OVERLAY ee BOT-OO02E seer 1 OF]

Page 32

L

PUR

BL.

KEYING PIN GRY

BL Bau L fever ess] > | P2 RIGHT WHT eet _o>o+4 FRONT PANEL cwaS5I5 GND

PI IS THE LEFT PLAYER FACING THE GAME.

P2 15 THE RIGHT PLAYER FACING THE GAME.

TRANS FORM ER’

lpz pown a oF

RED & ORN [eoom 8

Yeu

WHT

ow ® PUR RY. POWER

q @— Kevine pw @ stk GRN PLUG 4 0 ° a 50s—o

° OFF

ALTERNATE WIRING FOR 3 POS- OFF SWITCH

TRIGGER START SINGLE

1B INCH FLUORESCENT LAMP

BACK VIEW

yEL

+5 BU

Q—revine PIN SORE ¢ YEL__ +0 TRANSFORMER PINE

B1,52,83,S495ARE MOUNTED TO +5 END OF R2. o

ON COINMECH DOOR Ou PowER surPLy/amp. BD| COM NO.

POWER INTERRUPT BO7-0012

VOLUME INTERLOCK SWITCH

POWER BOX

To TPS ON VIDEO Loaic BD.

To TP4 ON VIDEO Locit BD.

SHIELDED WIRE

KEYING PINS

F Re 19 INCH MONITOR

GREMLIN INOUSTRIES INC. 8401 AERO DR. SAN DIEGO,CA. 92123) SCHEMATIC — BLOCKADE CABINET WIRING ERE 707-0001

Page 33

FLUCRESCENT LAMP FIXTURE, I8" P/N 390-0012 , SPEAKER,OVAL 6x9 = ——— Se = P/N 130-0001

OPERATOR SW ITCH . PERAT ss TOR BM bbe ASSY OPERATOR SWITCH ASSY

N 807-0004 REAR VIEW = Menton enasss a

paz BLK. TO LAMP ae sO" ee acy omer arte FR) To MONITOR, WAT" 1 ‘TO MONITOR, @F I .

Ser) ze === ™~10 OPERATOR VIDEO LOGIC BOARD Assy. P/N 807-0001 IGREMLIN INDUSTRIES INC, $401 AERO OR. SAN DIEGO, CA. 92123 CABINET WIRING BLOCKADE DE TENT. RO. [BRAWRe Wo. 107-0001