CATHODE RAY TOMES

Metro Cross

Metro-Cross (set 1) (Namco, 1985) · Manual · 11 pages · 9 sections · original scan

Page 1

CONVERSION KIT INSTRUCTION MANUAL FOR CABINETS WITH HORIZONTAL-MOUNT COLOR RASTERSCAN MONITOR

©1985 ¢ LICENSED FROM NAMCO, LTD., JAPAN ¢ ALL RIGHTS RESERVED

2250 ELMHURST RD. Ki ITKO R | ELK GROVE VILLAGE, IL 60007 (312) 228-0451 FAX (312) 228-1563 TELEX 206424 KITKORP

Page 2

THE COMPLETE

METROCROSS

KIT INCLUDES:

PRINTED CIRCUIT BOARD UNIVERSAL WIRING HARNESS FOUR CONTROL BUTTON ASSEMBLIES COMPLETE JOYSTICK ASSEMBLY COLORFUL SIDE GRAPHICS CONTROL PANEL GRAPHICS MARQUEE PLEXI GAME PLAY INSTRUCTIONS FCC BOARD ENCLOSURE CONVERSION INSTRUCTION MANUAL BOARD SCHEMATICS

USER INFORMATION

WARNING

F.C.C. REGULATION COMPLIANCE

THE P.C. BOARD CAGE SUPPLIED WITH THIS CONVERSION KIT MUST BE UTILIZED AND TERMINATED TO GROUND AT THE TIME OF INSTALLATION. THIS IS TO AVOID RADIO FREQUENCY RADIATION AND COMPLY WITH THE LIMITS FOR A CLASS “A” COMPUTING DEVICE PURSUANT TO SUBPART “J” OF PART 15 OF F.C.C. RULES, WHICH ARE DESIGNED TO PROVIDE REASONABLE PROTECTION AGAINST SUCH INTERFERENCE WHEN OPERATED IN A COM- MERCIAL ENVIRONMENT. OPERATION OF THIS EQUIPMENT IN A RESIDENTIAL AREA IS LIKELY TO CAUSE INTERFERENCE — IN WHICH CASE, THE USER AT HIS OWN EXPENSE, WILL BE REQUIRED TO TAKE WHATEVER MEASURES MAY BE REQUIRED TO CORRECT THE INTERFERENCE.

Page 3

INTRODUCTION TO KITKORP’S METROCROSS

KITKORP’S METROCROSS KIT WILL GO INTO ANY GAME CABINET THAT HAS A

HORIZONTALLY-MOUNTED MONITOR AND A POWER SUPPLY THAT PROVIDES +5 VOLTS

DC AND+12 VOLTS DC. THE CONTROL PANEL REQUIRES AN 8-WAY JOYSTICK, LEFT AND RIGHT JUMP BUTTONS, PLUS 1-PLAYER AND 2-PLAYER START BUTTONS. THE BOARD GENERATES A NEGATIVE COMPOSITE SYNC SIGNAL THAT’S COMPATIBLE WITH THE MAJORITY OF THE GAME MONITORS IN USE.

METROCROSS OFFERS YOU AN OPTION TO USE LIT BUTTONS ON THE CONTROL PANEL FOR 1-PLAYER AND 2-PLAYER START. USE TRANSLUCENT BUTTONS AND WIRE LAMP SOCKETS (6-VOLT DC LAMPS WILL WORK) TO THE UNDERSIDE OF THE CONTROL PANEL NEAR THE BUTTONS. TIE ONE SIDE OF THE LAMP SOCKET TO THE APPROPRIATE TERMINALS ON THE EDGE CONNECTORS. DEPENDING ON COINS DEPOSITED, THE PLAYER START LAMPS WILL FLASH AND ILLUMINATE THE BUTTONS ON THE CONTROL PANEL.

METROCROSS ALSO PROVIDES A RAM-ROM TEST AND THE OPPORTUNITY TO PLAY ANY ONE OF ITS THIRTY-TWO SCREENS. SEE ‘DIPSWITCH SETTINGS’ PAGE FOR INFORMATION ON THESE FEATURES.

METROCROSS CONVERSION INSTRUCTIONS

OUTSIDE CABINET

Remove all the ‘old’ game graphics: marquee, control panel overlay, and side decals. TIP: Usea hair dryer or heat gun to heat up and soften the adhesive on the overlay and side decals. This makes removal easier.

When you've stripped off the side decals, wet down the cabinet sides with mineral spirits (paint thinner) and scrape gently with a paint scraper. The mineral spirits soften the residual adhesive.

CAUTION: The mineral spirits may damage some cabinet finishes, especially surfaces that have been repainted. Test an inconspicuous corner first. Dry the cabinet sides thoroughly

Use a spray bottle or sponge to wet the cabinet sides with a solution of dish soap or mild sudsing detergent. Apply the side decals onto this wet surface. This gives you time to position the decal properly. When the decal is in place, use a squeegee to smooth it out. Work from the center; press firmly to squeeze out bubbles and liquid. The decal will dry and ‘set up’ in 48 hours or so and be smooth and bubble-free. During this drying time, be careful not to wrinkle or tear the decals

Take the control panel and remove all the ‘old’ buttons and joysticks. Decide whether you need to strip off the old overlay. If it is clean and smooth, or if there is no overlay, the Metrocross overlay will adhere neatly to the control panel. Before you apply the Metrocross overlay, though, be sure the control panel has the required number of holes

TIPS: Use a 1%" wood auger bit or hole saw for drilling holes in wooden control panels. An auger bit is less expensive than a hole saw, but a hole saw is easier to use and makes cleaner holes.

Cut perfect holes in metal control panels with a round metal punch (also called a chassis punch). The 1-3/16" size is best for industry-standard control panel buttons and is available at most hardware stores. Keep a small can of 20-weight oil with your punch; oil the threads and cutting edge liberally during use.

Page 4

Extra holes on the control panel should be filled with epoxy, wood putty, or auto body filler (‘Bondo’) to avoid ‘soft spots’ on the overlay.

Apply the Metrocross overlay to the control panel. Cut out the holes with asharp knife and apply the Player Start, Jump button, and Joystick labels. Install the joystick and buttons.

Cut the marquee to size. If you don’t have a bandsaw, a jigsaw or sabre saw with a plasticcutting blade works nicely.

Apply the game instructions to the game glass or, if you like, onto the control panel.

INSIDE CABINET Remove the ‘old’ game wiring harness (except the AC line harness) and take out the old game boards. NOTE: The cabinet you're converting may easily have the same control panel configuration and the same type board edge connector as Metrocross. If this is the case, save yourself some time by using the existing harness. Rearrange the wires on the existing edge connector or splice the existing wires onto the connector provided in the Metrocross kit.

NOTE: The voltage supply leads and power supply ground leads are all heavier-gauge wire. This is to assure the best possible power and ground distribution. Don’t short change your game: connect both +5v leads and both ground leads (along with the +12v lead) to the power supply. i Be sure you find and use the harness with the 6-pin plug. This is the video harness and connects to J2 on the Metrocross printed-circuit board.

There is no harness for connector J1. It is not used.

For ease of installation, the harness edge connector is keyed. The key fits into the slot on the board edge connector. Don't forget to install the RF cage as required by the FCC. Be sure it’s grounded.

Page 5

WIRING HARNESS ROUTING

TO POWER SUPPLY

P.S. GND BLK

P.S. GND BLK

+12 VDC ORN

+5 VDC RED

+5 VDC RED

SPEAKER

SPKR+ WHT-BLU

SPKR- WHT-BLK

COIN DOOR

COINSW. 1 YEL

GND BLK

CONTROL PANEL

41P START = WHT-YEL rm) Ga zo rand ae) rw z uz ao a Fas) (3)

2P START =WHT-ORN

1P JUMP WHT-RED

1P LEFT YEL-RED 1P DOWN -YEL-BLU ‘

1P RIGHT YEL-GRN

1P UP YEL-WHT

GND BLK

GND BLK

GND BLK

VIDEO CONNECTOR J2

VID RED = RED VIDGRN = GRN J2 VID BLU BLU

VIO SYNC = WHT

VID GND BLK

SUGGESTED CONTROL PANEL LAYOUTS

JOYSTICK JOYSTICK oo boo oboe 1P START [ NZ XZ O-~2P START JUMP JUMP 1P START 2P START

Page 6

EDGE CONNECTOR DIAGRAM

PARTS SIDE ______ SOLDER SIDE __ POWER SUPPLY GROUND POWER SUPPLY GROUND __ BLACK [A] 1{ BLACK SPEAKER + SPEAKER- ___WHITE-BLUE |B [ro | WHITE-BLACK *COIN LOCKOUT COIL | C @

COIN COUNTER 1°

“1P START LAMP. 2P START LAMP” +12 VOLT suppLy |_| | +12 VOLT SUPPLY” _ ORANGE | E;S. a +5 VOLT SUPPLY +5 VOLT SUPPLY _ RED | F}6| RED | GROUND GROUND BLACK |H|7| BLACK “SERVICE SWITCH | J | 8 COINSWITCH 1 YeLtow | k|9 ee 1P START 2P START a WHITE-YELLOW | L 110 _WHITE-ORANGE | 1P JUMP. 2P JUMP* WHITE-RED [M11] _ 1P JOYSTICK LEFT 2P JOYSTICK LEFT" | YELLOW-RED_|N|12 ee 1P JOYSTICK DOWN 2P JOYSTICK DOWN’ YELLOW-BLUE | P|t 1P JOYSTICK RIGHT _YELLOW-GREEN | R|14 1P JOYSTICK uP 2P. JOYSTICK UP" YELLOW-WHITE |S [15 2P JOYSTICK RIGHT”

“COIN COUNTER 2 THIS TERMINAL TO

_ Y |21| GROUND FOR COCKTAIL _| GROUND GROUND BLACK |2|22| BLACK

  • TERMINALS LABELED * ARE FOR OPTIONAL USE AND ARE NOT WIRED.
  • START LAMP TERMINALS AT D AND 4 ARE FOR USE WITH LICON-TYPE BUTTONS OR UNDERLIT TRANSLUCENT BUTTONS. SUPPLY VOLTAGE IS +5VDC
  • SUPPLY VOLTAGE FOR COIN LOCKOUT COIL (TERMINAL C) AND COIN COUNTERS (TERMINALS Y, 3) IS +12VDC.
  • TERMINAL 21 SHOULD BE GROUNDED FOR COCKTAIL TABLE USE.
Page 7

VIDEO CONNECTOR J2

VIDEO RED VIDEO SYNC J1 (NOT USED)

RED1WHITE

KEY VIDEO PLUG J2 A z VIDEO GREEN ©) G] VIDEO GROUND yA - -

GREENBLACKOmin oco eal

{

VIDEO BLUE[3 ») ‘G)\A] Sowswircn i
BLUEVOLUME\A|

CONTROL \ DIPSWITCH

  • THIS BOARD GENERATES NEGATIVE COM- 8 POSITE SYNC. THE WHITE SYNC OUTPUT WIRE GOES TO BOTH THE HORIZONTAL METROCROSS
ANDVERTICALNEGATIVECOMPOSITEPRINTED CIRCUIT

SYNC INPUTS ON THE MONITOR BOARD |

  • CONNECTOR J1 ON THE BOARD IS NOT | USED. a a a

DIPSWITCH SETTINGS

DIPSWITCH A r1t2}3ata]s5{e6]7 ] 8 _ SELF-TEST MODE _. IN

GAME MODE Lorr

COINS/CREDITS 1 | 12_| 2h.

GAME DIFFICULTY men (Sil LOFE. | OFF: | OFF | ON "HARD — | on | oF | VERY HARD on | OFF BUY-IN (AFTER | 4th ROUND ONLY) ON NO BUY-IN OFF COINS/CREDITS _COINSWITCH 2 orF | OFF FF | ON ON | OFF | on | on

DIPSWITCH B12345678

ATTRACT MODE | SOUND NO | ON YES | OFF ROUND ADVANCE * OFF {SEE NOTE BELOW) ON | (NOT USED} NORMAL GAME MODE OFF [FREEZE SCREEN _| ON | NORMAL MODE OFF

“TO ADVANCE ROUNDS: SET SWITCH 2 TO'‘ON.’ COIN UP GAME AND PUSH 1P START. USE JOYSTICK TO SELECT ROUND 1 THRU 32. SET SWITCH 2 TO ‘OFF’ TO PLAY THE ROUND YOU HAVE SELECTED.

Page 8

LOSGE7ZZ

eum “a HRW 3 Be tee Ban Samco i : a ; eS

lake saa = om + save Sas ae ae ed See Spel PASE

BRRERERR i

| i |

Iser28 | |

a

1 CPE IV, 2 TaM-RIT TLE? 3 MRY E2590 4 LYFE Sy

Page 9

l.

i al Live | a “ RESET

aye hr i

= | [ee ee ==

TEASER paper BEapaa

Su pE/ We FV) 2 74A-KI TT Lit ate | ER BFS DWT F LY CHEE, 22 CHELSV.

Page 10

S855

55. Mal

matt MAIO: mag mae maT HAS

HAS bac BA: MAD Hat HAO

StH SASSSRES ae A asnepasat

eH

BHA in HA

le yt

Lal

Page 11

an Tem,

aa E h

=

1” me

woren | she i wen :

ra}

ou —H

apo?

‘x

oe # one cs fe ae fF

zpateca

of at = 8

ahheadaxae + Ao
Eeaebes
ataEaeSee

21 Qu/VIDF/VOF/Wc tae, REVISION oon 2 TAROT T Lit 74¢4m, fame ra Van CAME PC BRB (%) ITD 22439502