Super Pac-Man General Instructions
Super Pac-Man (Namco, 1982) · Manual · 46 pages · 33 sections · original scan
SUPER PAC-MAN
General Instructions
silly MIDWAY MFG. CO. a
GENERAL _ INSTRUCTIONS
FOR
SUPER PAC-MAN
INSTALLATION
- Unlock and open the coin box door.
- Remove four (4) "CABINET LEVELING LEGS" from inside the coin box.
- Tip the cabinet to the side and remove the shipping cleats from its bottom.
° Locate the threaded holes - one in each corner - and install the "CABINET LEVELING LEGS" in them.
° Level the cabinet.
° When finished, the cabinet should be stable in the upright position.
- Plug the game into a standard A.C. wall outlet ONLY .
--WARNING- -
Game MUST be properly grounded.
- The power ON/OFF switch is located:
° UPRIGHT MODEL: On top of the cabinet toward the back.
° COCKTAIL TABLE MODEL: Underneath the cabinet on Player No. 2's side.
LINE VOLTAGE SAFETY INTERLOCK SWITCHES
Line voltage SAFETY INTERLOCK SWITCHES have been provided for your protection. The locations of these SAFETY INTERLOCK SWITCHES are:
- UPRIGHT MODEL: Inside the rear of the cabinet on the right side of the rear access door.
- COCKTAIL TABEL MODEL: Inside the cabinet on the hinge side of the coin door.
PART NO. M051-00316-A011
When the cabinet access door(s) are secured in place, the SAFETY INTERLOCK SWITCH plunger(s) are in a fully depressed condition. The game circuit can function normally.
When any cabinet access door(s) are opened, the SAFETY INTERLOCK SWITCH plunger(s) are in a partially extended condition. This isolates the game circuit from the line voltage.
To restore power to the game circuit with the access door(s) open, gently pull the SAFETY INTERLOCK SWITCH plunger(s) out to the fully extended condition. THIS IS TO BE USED FOR ‘SERVICING THE GAME ONLY! Se
SELF-TEST
Slide switches are provided to make the game run a "Self-Test" on itself. The SELF-TEST SWITCHES are located on a mounting bracket on the inside left hand side of the coin door.
When in the Self-Test mode, the monitor screen will display the results of certain test functions it has run on itself. (These will be discussed in more detail later.)
TO SERVICE THE CONTROL PANEL(S)
- UPRIGHT MODEL:
° The control panel is held in place by three latches, one on the left side, one on the right side, and one in the center of the front of the cabinet.
They are spring loaded to provide constant positive pressure on their latch plates.
They can be reached through the coin door AFTER turning power to the game off.
To release the latches, lift up and toward the center of the control panel.
Once they are released, unhook them from their latch plates.
To remove the control panel:
Raise it up and tilt it toward you until you can see the cable behind it.
Cradling the control panel between yourself and the cabinet, disconnect it from its cabling and nylon retaining strap.
The control panel is now free and can be removed.
° To reinstall the control panel(s), reverse this procedure.
- COCKTAIL TABLE MODEL:
° Each control panel is held in place by several screws, two on the inside of the cabinet and three along the bottom edge of the control panel.
Turn the power off to the game.
Open the coin box door and release the two latches on the inside of the cabinet up next to the table top.
Once they're released, unhook them from their latch plates.
Grasp the table top in the center above the coin door Lifting up and to the side to tilt it open.
Remove the screws which secure the control panel in place.
To remove the control panel(s):
Disconnect it from its cabling.
The control panel is now free and can be removed.
° To reinstall the control panel(s), reverse this procedure.
REMOVAL OF THE MAIN-DISPLAY-GLASS AND/OR THE T.V. BEZEL ASSEMBLY
- UPRIGHT MODEL:
nN
Turn the power to the game off and remove the control panel. This frees the main-display-glass so it can be lifted up.
By putting your finger in the hole in the middle of the main-display-glass support, you can Lift it up and out.
Loosen the screws which secure the T.V. bezel-glass-clamps in place.
Move the clamps to the side and the bezel glass may be removed.
Remove the above mentioned‘ screws and the bezel with four bezel-glass-clamps may be removed.
To reinstall the T.V. bezel asssembly and the main-display-glass, reverse this procedure. .
COCKTAIL TABLE MODEL:
-4e
Remove the screws which secure the table top glass clamps in piace.
Remove the table top glass.
Loosen the screws which secure the T.V. bezel-glass-clamps in place.
Move the clamps to the side and the bezel glass may be removed.
Remove the screws which secure the bezel assembly to the table top and the bezel with four bezel-glass-clamps may be removed.
To reinstall the T.V. bezel assembly and the table top glass, reverse this procedure,
VOLUME CONTROL POT
The volume control pot is located on the C.P.U. board. The other board is the Video board. There is only one pot. For adjustment, it may be reached through the rear access door on the UPRIGHT models. On the COCKTAIL TABLE models, you will have to open the table top to reach it.
To make the sounds louder, turn the pot clockwise as you face it (—sa),
To make the sounds less loud, turn the pot counterclockwise as you face it (46),
VOLTAGE CONTROL POT
The voltage control pot is located on the Power Supply P. C. Board. It is pre-set at the factory and SHOULD NOT be tampered with at all unless the distributors service department is contacted first.
SELF-TEST
The Self-Test mode is a special mode for checking game switches and computer functions. It is the easiest and best way to check for proper operation of the entire game.
You may begin a Self-Test at any time after the power to the game is or by sliding the Self- Test switch to the "ON" position. Now that the game is in the Self-Test mode, it will act as follows:
° First, you will see a moving multicolored pattern appear on the screen.
° Immediately following this, a rightside up test display is shown on the monitor screen. The game will remain in this Self-Test mode until you set the Self-Test switch back to the "OFF" position. This test display is shown below.
SELF - TEST DISPLAY
RAM OK ROM OK I/O OK TABLE 1ST COIN 1 CREDIT 2ND COIN 1 CREDIT PAC-MAN 3 RANK 8 SOUND 00 1ST BONUS FOR 30000 PTS 2ND BONUS FOR 100000 PTS
RAM TEST INDICATIONS AND THEIR MEANINGS
INDICATION MEANING CHIP LOCATION
RAM OK RAM 1 RAM 2 RAM 3 RAM 4 RAM 5 RAM 6 RAM 7 NO RAM IS OUT OF ORDER RAM 1 on VIDEO PCB is no good 2E RAM 2 on VIDEO PCB is no good 2H RAM 3 on VIDEO PCB is no good 2K RAM 4 on VIDEO PCB is no good 23 RAM 5 on C P_U PCB is no good 3K RAM 6 on C P U PCB is no good 3L RAM 7 on C P U PCB is no good 2D
ROM TEST INDICATIONS AND THEIR MEANINGS
INDICATION
ROM OK ROM 1 ROM 2 ROM 3
1/0 TEST INDICATIONS AND THEIR MEANINGS
INDICATION
1/0 OK 1/0 1 1/0 2
° MEANING CHIP LOCATION
NO ROM IS OUT OF ORDER ROM 1 on C PU PCB is no good 1c ROM 2 on C PU PCB is no good 1B ROM 3 on C P U PCB is no good 1K
MEANING CHIP LOCATION
NO BIT IS OUT OF ORDER BITC PU 1. is out of order ar BIT CPU 2 is out of order 4c
If a bad ROM or RAM chip is found by the games internal check system during the Self- Test, the game indicates this to you by showing the P.C. Board location code of the bad chip(s) in place of the letters "OK":
° To check your game function switches and buttons (coin counter switches, SUPER SPEED Button, 1 PLAYER and 2 PLAYER buttons, etc.): activate each one while the game is in You should hear a game sound for each button or switch activated. the Self-Test mode.
«6 =
If you do not hear it, the switch/button is either not working, miswired, or disconnected. Check it out thoroughly.
"RANK" is a difficulty setting, with "RANK 1" being the least difficult level of play and "RANK B" being the most difficult level of play. "RANK AUTO"; at these settings the game measures the players skill level and progressively gets harder as the player gets better. "RANK C" is the least difficult level of "AUTO" play and "RANK F" is the most difficult level of "AUTO" play. See "OPTION SWITCH SETTINGS TABLE".
To check "SOUND":
A. Move the controller to the right momentarily and release it - "SOUND" number changes from "00" to "01" and you hear "SOUND 01".
B. Repeat Step "A" above and "SOUND 01" will change to "SOUND 02" and it is heard.
Cc. Repeat Step "A" above again and "SOUND 02" changes to "SOUND 03" and it is heard and so on.
When finished with the Self-Test mode, slide the Self-Test switch back to the "OFF" position,
A. A cross hatch pattern appears on the monitor screen for about 1 to 2 seconds.
B. If you wish to keep this test pattern on the monitor screen for further use, slide Self-Test switch to the "ON" position after the cross hatch pattern appears and before it disappears.
c. When finished with the cross hatch pattern, set the Self-Test switch to the "OFF" position.
D. Normal game functions will now return to the monitor screen.
SUPER PAC-MAN OPTION SWITCH SETTINGS
DIP SWITCH SW-3 AT LOCATION 5E
DIP SWITCH SW-2 AT LOCATION 58
COINS PER CREDIT—COIN SWITCH 1
SWH1 SWH2 SWH3 SWH4 SWHS SWHE SWH7 SWHB
DIFFICULTY LEVEL SETTINGS—“R1” IS
THE EASIEST AND “RB” IS THE MOST DIFFICULT
*1—-CON 1-CON 1-CON 1—COIN 1-CON 2—-CONS 2-COINS 3-COINS 1—CREDIT OFF OFF OFF 2-CREDITS OFF OFF 3-CREDITS ON OFF 6-CREDIIS ON OFF T—CREDITS OFF ON 1—CREDIT OF Of S-CREMTS On ON _1—CREDIT ono sSsatebs RANK “RO”—STANDARD LEVEL OF DIFFICULTY WHET SWH#2 SWH#S SWi#4 SWS SWHIG SWH7 SWHB
OFF OF OFF OFF
BONUS SUPER PAC-MEN AWARDED AT THE FOLLOWING POINT VALUES:
BEGAN WITH 1, BEGAN WITH 2.0R 3 SUPER PAG-MEN 5 SUPER PAC-MEN | SWHT SWH2 SWH3 SWH#4 SWHS SWHG SWH7 SWHB
*1STSP-M 30000 1STSP-M © 30000 2NDSP-M_ 100000 20S P-M 100000 OFF OFF OFF RANK “R1”—EASIEST LEVEL OF DIFFICULTY
RANK “R3” RANK “R4” RANK “RS” RANK “RG” GRADUATED LEVELS OF DIFFICULTY
RANK “RI” *RANK “RO"--FACTORY SETTING RANK “RQ” RANK “RA” RANK “RB”—HARDEST LEVEL OF DIFFICULTY OW OFF OFF OFF OF OFF i] OFF OFF OF ON OFF ON ON OFF OF ON OFF on On OFF OF OF On OF OF OF oH OFF
1STSP-M 30000 1STSP-M © 30000 2D SP-M 80000 2NDSP-M 120000 on Orr
1STSP-M 30000 1STSP-M © 40000 20S PH 120000. 2NDSP-M 120000 OFF RANK “RC”—EASIEST AUTO DIFFICULTY SETTING
RANK “RU” RANK “RE” RANK “RF”—HARDEST AUTO DIFFICULTY SETTING OFF OW On OW OFF OW On Oh ON ON
Bsstbssbisstbs
ISTSP-M = 30000 1STSP-H = 30000 OFF COINS PER CREDIT—COIN SWITCH 2
TSTSPM 30000 1STSP-M = 40000 OFF AND EVERY 80000 AND EVERY 100000 OW AND EVERY 100000_AND EVERY OF 120000 On
1ST SPM 30000 oMLY AND EVERY 120000 1S P-MP 30000 ow On *1-COIN — 1-CREDIT 1-COIN = 2—CREDITS 2—COINS = 1—CREDIT 2—COINS — 3--CREOITS WHHL SWH2 SWHES SWHE4 SWHS SWHE SWH7 SWHEB
OF OF ON OF OF ON On
OWLY OnLy 1SPMAT 30000 1SP-MAT 40000 OFF OW SOUND
Bs s & B ses NO BONUS SHIPS GIVEN WITH THIS SETTING OW DETERMINES NUMBER OF SUPER PAC-MEN PLAYER BEGINS GAME WITH: *SOUND NO SOUND SET SEZ WHS SHEA SHES SH ST SW ww
SWH#1 SWH2 SWH3 SWHE4 SWHS SWHG SWH7 SWHB SCREEN
*3 SUPER PAC-HEH 1 SUPER PAG-HAN ON OFF 2 SUPER PAC-MEN OF ON 5 SUPER PAC-MEN On OW OF OF *HORMAL OPERATION FREEZE VIDEO T SWHT SWH2 SWH3 SWH4 SWHO SWHE SWHT SWHO OF
INDICATES FACTORY RECOMMENDED SETTINGS PART NUMBER W051-00316-B012
VI Technical Troubleshooting
Introduction
The most common problems occur in harness components such as the coin acceptor, player controls, interconnecting wiring, etc. The TV monitor and PCB computer cause their share of problems too, but not as much as the harness and its component parts. TV monitor troubleshooting will not be covered here because it is covered in that section of this manual. As you already know, the PCB computer is a complex device with a number of different circuits. Some circuits remain basically the same among games, but overall there are a great many differences between them. PCB troubleshooting procedures, therefore, can be lengthy and will differ greatly among games. However, some basic Z-80 CPU information is involved in this section.
General Suggestions correctly identifying the maffunction’s symptoms
The first step in any troubleshooting procedure is correctly identifying the maffunction’s symptoms. This includes not only the cifcuits or features malfunctioning, but aiso those still operational. A carefully trained eye will pick up other clues as well. For instance, a game in which the computer functions fail completely just after money was collected may have a quarter shorting the PCB traces. Often, an experienced troubleshooter will be able to spot the cause of the problem even before opening the cabinet.
After all the clues are carefully considered, the possible malfunctioning areas can be narrowed down to one or two good suspects. Those areas can be examined by a process of elimination until the cause of the malfunction is discovered.
Harness Component Troubleshooting
Typical problems falling in this category are coin and credit problems, power problems and failure of individual features.
6-1 NO GAME CREDIT For example, your prospective player inserts his quarter and is not awarded a game. The first item to check is if the quarter is returned. If the quarter is returned, the malfunction most certainly lies in the coin acceptor itself. First, use a set of test coins (both old and new) to ascertain that the player's coin is not undersize or underweight. If your test coins are also returned, coin acceptor servicing is indicated. Generally, the cause of this particular problem is a maladjusted magnet gate. Normally, this will mean slightly closing the magnet gate a little by turning the adjusting screw out a bit (see section on coin acceptor for more details). If the quarter is not returned and there is no game credit, the cause of the malfunction may be in one of several areas. First try operating the coin return button; if the coin is returned, the problem is most likely in the magnet gate. Enlarge the gap according to the coin acceptor service procedures. If this does not cure the problem, remove the coin acceptor, clean it and perform the major adjustment procedure. If the trapped coin is not returned when the wiper lever is actuated, you may have an acceptor jammed by a slug, gummed up with beer, a jammed coin chute, or mechanical failure of the acceptor mechanism. In this case, first check for the slug that will generally be trapped against the magnet. If so, simply remove the slug and test the acceptor. If the chute is blocked, remove the acceptor and remove the jammed coins. If there is actual failure of the acceptor, remove the unit and repair as indicated in the coin acceptor service procedures. If the coin is making its way through the acceptor (that is, falling into the coin box), yet there is still no game credit, you either have a mechanical failure of the coin switch or electrical failure of the coin and credit circuits. The first place to begin is by checking the coin switch. Most of these switches are the make/break variety of micro switch, which is checked by testing for continuity between the NO, NC, and C terminals. When not actuated, the NC and C terminals should be continuous and the NO terminal open. When operated, the NO and C terminals should close and the NC should be open. If the coin switch checks out, examine the connections to the terminals to make sure there is good contact. If necessary, use the continuity tester and check from the terminal lug on the switch to the associated PCB trace. This will tell you if there is a continuous line all the way to the credit circuit.
If the coin switch wires do not check out, the problem is in the computer — most likely in the coin and credit circuitry. If you do get game credit when a coin is deposited, but the game will not start when the start switch is pressed, you may have a problem in the start switch, the interconnecting wiring or in the computer. First check the switch. If the switch is OK, proceed to check the wiring. Again, make sure you go from the terminal lug on the switch to the PCB trace, This way, you will check the terminal contact as well as PCB edge connector contact. If the wiring is continuous, proceed to check the PCB credit circuit. If not, check each section of the wiring, until the discontinuity is located. If the wiring is OK, the problem must lie in the computer.
Transformer and Line Voltage Problems
Your machine must have the correct line voltage to operate properly. If the line voltage drops too low, a circuit in the computer wiil disable game credit. The point at which the computer will fail to work will vary some from game to game, but no game'will work on line voltage that drops below 105 VAC. Low line voltage may have many causes. Line voltage normally fluctuates a certain amount during the day as the total usage varies, Peak usage times occur mainly at dawn or dusk, so if your machine's malfunction seems to be related to the time of day, this may be a factor. A large load connected to the same line as the game (such as a large air conditioner or other device with an exceptionally large motor) may drop the line voltage significantly when starting up. This drop can result in an intermittent credit problem. In addition, poor connections in the location wiring, plug, or line cord may also cause a significant drop in power. Cold solder joints in the game’s harness, especially in areas like the transformer connections, interlock switch, or fuse block, may also produce the same results, although probably on a more permanent basis. Sometimes location owners (especially in bars) replace light switches with dimmer rheostats, and the game is sometimes on the same line. Obviously, the voltage available to the game is going to drop dramatically when the dimmer is turned. In any case, the way to check for correct line voltage is with your VOM. Set the VOM to 250 VAC and stick the probes in the wall receptacle. If it's OK here, check the transformer primary connections. If you do not get 117 VAC, examine the solder joints on the transformer, fuse block, and interlock switch. If you do get 117 VAC, the problem must be either in the transformer, harness connections, or in the PCB power supply.
6-2 \f you suspect the transformer, check its secondaries with the VOM set to 50 VAC and correlate the readings with the legend on the side of the transformer, The transformer must also be correctly grounded, so check the ground potential as well, especially if there is a hum bar rolling up ordown the TV screen.
HARNESS PROBLEMS Other harness problems include biowing fuses and malfunctioning controls. The repeating blown-fuse problem can sometimes be quite exasperating to solve, for short circuits have the tendency to occurin areas almost impossible to find. First, try inserting a new fuse, as Old fuses age and blow without cause. If the new one also blows, you definitely have a short. The best way to approach this problem is by turning the power off and disconnecting devices that maybe causing the problem, such as the TY, transformer, and PCB. Disconnect the devices by pulling off their connectors, but do not allow them to touch. If necessary, insulate them with small pieces of electrical tape. Then, connect your VOM across the terminals of the fuse block (all electrical power shut off), and set it to one of the resistance scales. This will save blowing a fuse each time you want to check the circuit. \f the VOM reveals that disconnecting the devices removed the short, reconnect the devices one by one until the short returns. The last device connected is the one that is at fault. If the VOM reads a short even after the devices are disconnected, the fault must lie in the harness itself, and only patient exploration will! reveal its location. First, carefully examine all the wiring, looking for terminals that may be touching, metal objects such as coins shorting connections or burned insulation. If necessary, use the VOM to check each suspected wire. MALFUNCTIONING CONTROLS One of the most common problems here is a bad potentiometer. Typically, a bad pot will cause the image to jump as it reaches a certain point. The only cure for this one is to install a new pot. if a feature that is operated by a switch (for example, joysticks, foot pedals, control panel buttons) does not operate at all, check the switch with a VOM or continuity tester to verify its operation. If the switch does not check out, replace it. If the switch is OK, you should suspect the input to the switch from the PCB. In this case, get out the harness and logic schematics and check to see what kind of input itis. In many cases, the input will be +5 VDC. If so, use the VOM to check its presence. Normally, the switch is used to pulla +5 VDC line LOW to GND or to pull a LOW line HIGH. If the PCB output is missing, check the wire length from the PCB. If you find the signal at the PCB trace, the wire length or connection is at fault. If not, begin exploring the PCB using the logic schematics.
A Glossary of Microprocessor Terms
MICROPROCESSOR — one or several microcircuits that perform the function of a computer's CPU. Sections of the circuit have arithmetic and comparative functions that perform computations and executive instructions.
CPU — central-processing unit. A computing system’s “brain”, whose arithmetic, control and logic elements direct functions and perform computations. The microprocessor section of a microcomputer is on one chip or several chips. PROM — programmable read-only memory. User permanently sets binary on-off bits in each cell by selectively fusing or not fusing eiectrical links. Nonerasable. Used for low-volume applications.
EPROM — erasable, programmable, read-only memory. Can be erased by ultraviolet light bath, then reprogrammed. Frequently used during design and development to get programs debugged, then replaced by ROM for mass production.
ROM — read-only memory. The program, or binary on-off bit pattern, is set into ROM during manufacture, usually as part of the last metal layer put onto the chip. Nonerasable. Typical ROM's contain up to 16,000 bits of data to serve as the microprocessor’s basic instructions. RAM — random-access memory. Stores binary bits as electrical charges in transistor memory cells. Can be read or modified through the CPU. Stores input instructions and results. Erased when power is turned off. LSI — large scale integration. Formation of hundreds ‘or thousands of so-called gate circuits on semiconductor chips. Very large scale integration (VLS) involves microcircuits with the greatest component density. MOS — metal-oxide semiconductor. A layered construction technique for integrated circuits that achieves high component densities. Variations in MOS chip structures create circuits with speed and low-power requirements, or other advantages (static will damage a MOS chip).
Introduction to the
Z-80 CPU
The term “microcomputer” has been used to describe virtually every type of small computing device designed within the last few years. This term has been applied to everything from simple “microprogrammed” controllers constructed out of TTL MSI up to low end minicomputers with a portion of the CPU constructed out of TTL LSI “bit slices.” However, the major impact of the LSI technology within the last few years has been with MOS LSI. With this technology, it is possible to fabricate complete and very powerful computer systems with only a few MOS LSI components. The Zilog Z-80 family of components can be configured with any type of standard semiconductor memory to generate computer systems with an extremely wide range of capabilities. For example, as few as two LSI circuits and three standard TTL MSI packages can be combined to form a simple controller. With additional memory and I/O devicesa computer can be constructed with capabilities that only a minicomputer could previously deliver. New products using the MOS LSI microcomputer are being developed at an extraordinary rate. The Zilog Z-80 component set has been designed to fit into this market through the following factors:
- The Z-80 is fully software compatible with the popular 8080A CPU. Existing designs can be easily converted to include the Z-80. The Z-80 component set is at present superior in both software and hardware capabilities to any other microcomputer system on the market today. For increased throughput the Z80A operating ata 4 MHZ clock rate offers the user significant speed advantages. Microcomputer systems are extremely simple to construct using Z-80 components. Any such system consists of three parts:
- CPU (Central Processing Unit)
- Memory
- Interface Circuits to peripheral devices The CPU is the heart of the system. Its function is to obtain instructions from the memory and perform the desired operations. The memory is used to contain instructions and in most cases data that is to be processed. For example, a typical instruction sequence may be to read data from a specific peripheral device, store it in a location in memory, check the parity and write it out to another peripheral device. Note that the Zilog component set includes the CPU and various general purpose I/O device controllers, while a wide range of memory devices may be used from any source. Thus, all required components can be connected together in a very simple manner with virtually no other external logic. Nn
General Purpose Registers There are two matched sets of general purpose registers, each set containing six 8-bit registers that may be used individually as 8-bit registers or as 16bit register pairs by the programmer. One set is called BC, DE and HL while the complementary set is called BC’, DE’ and HL’. At any one time the programmer can select either set of registers to work with through a single exchange command for the entire set. In systems where fast interrupt response is required, one set of general purpose registers and an accumulator/flag register may be reserved for handling this very fast routine. Only a simple exchange command need be executed to go between the routines. This greatly reduces interrupt service time by eliminating the requirement for saving and retrieving register contents in the external stack during interrupt or subroutine processing. These general purpose registers are used for a wide range of applications by the programmer. They also simplify programming, especially in ROM based systems where little external read/write memory is available. Arithmetic & Logic Unit (ALU) The 8-bit arithmetic and logical instructions of the CPU are executed in the ALU. Internally the ALU communicates with the registers and the external data bus on the internal data bus. The type of functions performed by the ALU include: Add Left or right shifts or rotates (arithmetic and logical)
Subtract Increment
Logical AND Decrement Logical OR Set bit Logical Exlusive OR Reset bit Compare Test bit Instruction Register and CPU Control As each instruction is fetched from memory, it is placed in the instruction register and decoded. The control sections performs this function and then generates and supplies all of the control signals necessary to read or write data from or to the registers, control the ALU and provide all required external control signals.
Z-80 CPU Pin Description The Z-80 CPU is packaged in an industry standard 40 pin Dual In-Line Package. The I/O pins areshown in the below figure and the function of each is described.
az 2 “_ «——
MREQ <——| SYSTEM tora) ~«——4 CONTROL 55 21
wR «—_]
RFSH <«——_
HALT =<——J
cpu WaT |= >} CONTROL
CPU 23 BUS asa <2 contro. °°“
+v0
GND) ———> 2-80 CPU
Z-80 PIN CONFIGURATION oe ADDRESS ree BUS
a ~~, DATA ~+—_ D, BUS = Ds
Ao-Ais (Address Bus) Tri-state output, active high. Ap-A;s constitute a 16bit address bus. The address bus provides the address for memory (up to 64K bytes) data exchanges and for I/O device data exchanges. I/O addressing uses the 8 lower address bits to allow the user to directly select up to 256 input or 256 output ports. Ao is the least significant address bit. During refresh time, the lower 7 bits contain a valid refresh address.
D,-D; (Data Bus) Tri-state input/output, active high. Dy-D; constitute an 8-bit bidirectional data bus. The data bus is used for data exchanges with memory and |/O devices.
My (Machine Cycle one) ___ Output, active low. M, indicates that the current machine cycle is the OP code fetch cycle of an instruction execution. Note that during execution of 2-byte op-codes, M1 is generated as each op code byte is fetched. These two byte op-codes always begin with CBH, DDH, EDH or FDH. M1 also occurs with [ORQ to indicate an interrupt acknowledge cycle.
MREQ (Memory Request) Tri-state output, active low. The memory request signal indicates that the address bus holds a valid address for a memory read or memory write operation. 1ORQ (Input/Output Request) Tri-state output, active low. The IORQ signal indicates that the lower half of the address bus holds a valid I/O address fora I/O read or write operation. An |ORQ signal is also generated with an M1 signal when an interrupt is being acknowledged to indicate that an interrupt response vector can be placed on the data bus. Interrupt Acknowledge operations occur during M, time while I/O operations never occur during M, time. RD (Memory Read) _ Tri-state output, active low. RD indicates that the CPU wants to read data from memory or an I/O device. The addressed 1/O device or memory should use this signal to gate data onto the CPU data bus. WR (Memory Write) _ Tri-state output, active low. WR indicates that the CPU data bus holds valid data to be stored in the addressed memory or I/O device. |
6-5 RFSH (Refresh) Output, active low. RFSH indicates that the lower 7 bits of the address bus contain a refresh address for dynamic memories and the current MREQ signal should be used to do a refresh read to all dynamic memories.
HALT (Halt state) Output, active low. HALT indicates that the CPU has executed a HALT software instruction and is awaiting either a non maskable or a maskable interrupt (with the mask enabled) before operation can resume. While halted, the CPU executes NOP’s to maintain memory refresh activity. WAIT (Wait) Input, active low. WAIT indicates to the Z-80 CPU that the addressed memory or I/O devices are not ready for a data transfer. The CPU continues to enter wait states for as long as this signal is active. This signal allows memory or I/O devices of any speed to be synchronized to the CPU. INT (Interrupt Request) Input, active low. The Interrupt Request signal is generated by I/O devices. A request will be honored at the end of the current instruction if the internal software controlled interrupt enable flip-flop (IFF) is enabled and if the BUSRQ signal is not active. When the CPU_accepts the interrupt, an acknowledge signal (IORQ during M, time) is sent out at the beginning of the next instruction cycle. The CPU can respond to an interrupt in three different modes that are described in detail in section 5.4 (CPU Control Instructions). NMI (Non-Maskable Interrupt) Input, negative edge triggered. The non maskable
interrupt request line has a higher priority than INT
and is always recognized at the end of the current instruction, independent of the status of the interrupt enable flip-flop. NMI automatically forces the Z-80 CPU to restart to location 00664. The program counter is automatically saved in the external stack so that the user can return to the program that was interrupted. Note that continuous WATT cycles can prevent the current instruction from ending, and that a BUSRQ will override a NMI. RESET Input, active low. RESET forces the program counter to zero and initializes the CPU. The CPU initialization includes:
- Disable the interrupt enable flip-flop
- Set Register | = 00H
- Set Register R =00x
- Set Interrupt Mode 0 During reset time, the address bus and data bus go to a high impedance state and all control ouput signals go to the inactive state.
BUSRQ (Bus Request) Input, active low. The bus request signal is used to request the CPU address bus, data bus and tri-state output contro! signals to go to a high impedance state so that other devices can contro! these buses. When BUSRQ is activated, the CPU will set these buses to a high impedance state as soon as the current CPU machine cycle is terminated.
BUSAK (Bus Acknowledge) Output, active low. Bus acknowledge is used to indicate to the requesting device that the CPU address bus, data bus and tri-state control bus signals have been set to their high impedance state and the external device can now control these signals.
CLK (Clock) Single phase TTL level clock which requires only a 330 ohm pull-up resistor to +5 volts to meet all clock requirements.
MCR II SYSTEM P.C. BOARD JUMPER OPTIONS
VIDEO GENERATOR P.C. BOARD
68764
68766
2564 |
2764
68764
68766
- = CUT JUMPER WIRES WHERE THIS SYMBOL ‘“*” APPEARS. # = LEAVE JUMPER WIRES IN WHERE THIS SYMBOL “#” APPEARS.
The above table illustrates the fact that the Video Generator P.C. Board used in the MCR I System has 8 jumper wires, the SUPER C.P.U. P.C. Board used in the MCR II System has 19 jumper wires, and the Sound I/O P.C. Board used in the MCR II System has 2 jumper wires.
All of the above Boards can be used with a variety of different SETS of EPROM chips. However, these EPROMS are not all made by the same manufacturer and do have some internal differences. So, in order to make them function properly in their respective P.C. Boards, certain jumper wires on these Boards have to be cut.
The above table tells you which jumpers to cut (depending on which EPROM set you're going to use) by showing a “*" under that jumper wire’s number. If there is NO “*” under a jumper wire's number, THAT PARTICULAR JUMPER WIRE IS NOT TO BE CUT.
VII. Coin Door Maintenance
SPECIAL NOTE: If you have any questions about the coin acceptors in your game(s), please feel free to contact their manufacturers. Each manufacturer's name is PROMINENTLY imprinted on every acceptor mechanism.
Metal mechanisms only: COIN MECHANISMS, INC. 817 Industrial Drive Elmhurst, IL 60126 Phone (312) 279-9150
COIN DOOR MAINTENANCE
METAL COIN ACCEPTOR MECHANISMS
Periodically, the metal coin acceptor mechanism(s) must be removed from the coin door and cleaned.
1, Make sure the power to the game is off.
- Unlock and open the coin door.
TO REMOVE PUSH LATCHES DOWN
PLACE PEGS IN SLOTS TO REPLACE PULL MECHANISM OUT Metal and Plastic mechanisms: COINCO COIN ACCEPTORS, INC. 860 Eagle Drive Bensenville, IL 60106 Phone (312) 766-6781
- Remove the coin acceptor mechanism as shown in Figure 7-1. O Push down on the two spring loaded latches. O While holding the latches down, pull the top of the coin acceptor mechanism toward you. O Release the latches and lift out the coin acceptor mechanism.
PUSH MECHANISM IN
Figure 7-1 Removing and replacing coin acceptor
4, Clean the magnet of all foreign particles. See Figure 7-2. 0 This may be accomplished by swinging the gate open as shown in the above figure.
- Remove the cradles and undersize levers and clean the bushings. (A pipe cleaner makes a good bushing cleaner.) D Also clean the pivot pin.
- Whenever needed, the coin acceptor should be cleaned with hot water and cleanser in the fallowing manner: O Place the coin acceptor in boiling water for about ten minutes.
OD Next, use a brush and kitchen cleaner to remove all remaining foreign matter from the unit. O Rinse the coin acceptor in clean boiling water. O Dry the coin acceptor thoroughly by using filtered compressed air to blow it dry.
GATE OPEN AS SHOWN CLEAN MAGNET BY DRAGGING A SCREWDRIVER BLADE ACROSS SURFACE
Figure 7-2 Cleaning the metal coin acceptor
- To lubricate the coin acceptor: O Use ONLY powdered graphite and put it ONLY on the moving parts of the coin acceptor. These parts are called out in Figure 7-3. O Be extremely careful to keep the powdered graphite away from paths that are traveled by the coins.
- WARNING — DO NOT USE OIL TO LUBRICATE THE COIN ACCEPTOR.
- Check the coin chute for obstructions such as: paper, gum, etc.
- Reinstall the coin acceptor to the coin door. See Figure 7-1. D Place the two pegs at the coin acceptor's base into their retaining slots. O Now push the top of the coin acceptor toward the coin door until it snaps in place and is held there by the two spring loaded latches.
- Close and lock the coin door.
APPLY POWDERED GRAPHITE HERE
UNDERSIZE LEVER
CRADLE
Figure 7-3 Lubricating the metal coin acceptor
SQUEEZE PINS TOGETHER TO UNLOCK
HOLDING BOTH GATES TOGETHER, PUSH UP AND PULL OUT
Figure 7-4 Opening the plastic coin acceptor
PLASTIC COIN ACCEPTOR MECHANISMS
The plastic coin acceptor mechanism(s) must be removed periodically from the coin door and cleaned.
- Make sure the power to the game is off.
- Unlock and open the coin door.
- Remove the coin acceptor mechanism(s) as shown in Figure 7-1. 1 Push down on the two spring loaded latches. While holding the latches down; pull the top of tne acceptor mechanism toward you. C Release the latches and lift out the mechanism.
- Squeeze the two pins indicated in Figure 7-4 together to open the mechanism and break it down into its three basic parts. O Clean the mechanism in hot soapy water. It never rusts. O Rinse the mechanism in clean hot water and allow it to dry.
7-3 O Reassemble the mechanism (it never needs lubrication).
- Check the coin chute for obstructions such as: paper, gum, etc.
- Reinstall the coin acceptor to the coin door. See Figure 7-5. O Place the two pegs at the coin acceptor’s base into their retaining slots. O Now push the top of the coin acceptor toward the coin door until it snaps in place and is held there by the two spring loaded latches.
- Close and lock the coin door.
ACCEPTOR CAN BE SET TO ACCEPT U.S. QUARTERS ONLY OR BOTH U.S. AND CANADIAN QUARTERS.
Se
SLIDE MAGNET TO EXTREME RIGHT (AS SHOWN) TO ACCEPT BOTH U.S. AND CANADIAN QUARTERS.
<<
TO ACCEPT U.S. QUARTERS ONLY, SLIDE MAGNET TO EXTREME LEFT.
Figure 7-5 Changing the plastic coin acceptor to accept American or Canadian quarters.
7-4
PLEASE NOTE:
THE INFORMATION CONTAINED IN THIS SECTION IS TOLD IN AN EASY TO UNDERSTAND MANNER AND IS INTENDED TO AID THOSE WITHOUT AN ELECTRONICS DEGREE IN TROUBLESHOOTING AND REPAIRING THEIR GAMES T.V. MONITOR.
IF YOU READ THROUGH THIS SECTION AND STILL HAVE QUESTIONS, PLEASE CONTACT YOUR DISTRIBUTOR OR MIDWAY MANUFACTURING COMPANY AT THE TOLL FREE NUMBER PROVIDED WITH YOUR GAMES PAPERS.
OUR STAFF AND OUR DISTRIBUTORS STAND READY TO HELP YOU!
THANK YOU
use this section of your manual.)
Color T.V.
Color T.V Monitor
Introduction: (How to
and take them seriously. The more equipment you have the better, but a low cost Voli-Ohm-Milliameter can often, do the trick. Here are the steps to take:
This section has been designed to simply familiarize you with one of the more mystical components in your game — the T.V. monitor. \f you are an electronics technician who is quite knowledgeable on the subject, you may decide to just go to the schematics and start troubleshooting the defective monitor. But if you are like most people, a monitor is a T.V. set, and that means a complex doo-dad that means big buck repairs. This isn’t necessarily so. This section of the manual will acquaint you with the monitor and could just help you repair it if you feel adventurous enough to give it a try. If you have any knowledge of electronics, especially the use of a voltmeter, the repairs you can make are astonishing. Just keep in mind that ELECTRICITY CAN BE VERY DANGEROUS, SO BE CAREFUL!
If you want to understand how a monitor works, just read the “THEORY OF OPERATION” subsection. If you wish, you can follow along with the schematics. The information is presented in a very basic manner but more complete treatment of the subject can be found in the technical sections of bookstores.
If you want to attempt to repair your monitor, it would be a good idea to read this whole section beginning to end before starting. Pay aitention to all warnings
8-1
- Find the symptom that matches the problems your monitor has in the “SYSTEM — DIAG- NOSIS” subsection. The diagnosis tells the circuit or area the problem may be in and possibly even the actual component causing it.
- Once you have the circuit that is causing the trouble, read the “TROUBLESHOOTING” subsection to learn the procedure for finding the bad part.
- Next, go to the schematic section and find the schematic that matches your monitor. It may be helpful to read the “DIFFERENCES BETWEEN MONITORS” subsection if you are unsure of which monitor you have. Use the schematic to see what parts are in the offending circuit.
That really is all there is to it. Just remember that there are some bizarre or rare symptoms not covered, or that a monitor may have two or more different problems that only a genius, the experienced, or an experienced genius can figure out. But be patient, follow safety precautions, and remember that there is also literature available from the monitor companies through your distributor or from Midway Manufacturing Company on request. (There is a toll free number on the back side of the front cover of this manual.)
Symptom Diagnosis
. Insufficient width or heighth: A. Horizontal line (due to VERTICAL CIR- CUIT DEFECT). D Bad yoke. O Bad veriical output section. O Open fusible resistor in vertical section. O Bad height control. O Bad flyback. B. Vertical tine (due to HORIZONTAL CIR- CUIT DEFECT). D Bad yoke. O Open width coil. O Open part in horizontal output section. Picture spread out too far or crushed in certain areas: A. Horizontal or vertical output transistor. B. Bad component in output circuitry. . Line too close with black spacing: A. Problem in vertical section causing poor linearity. } Poor focus and convergence: A. Bad high voltage transformer (“flyback”) or control. B. Focus voltage wire not connected to neckboard terminal. . Colors missing; check: Interface color transistors. Color output transistors. Cracked printed circuit board. Color circuits. . Video input jack. MOOD>P . Picture not bright enough: A. Weak emission from picture tube. (Turn horizontal sync off frequency and put brightness all the way up for about 15 minutes. Occasionally this cures the problem.) . Silvery effect in white areas; check: A. Beam current transistors. B. Weak picture tube emission. . Too much brightness with retrace lines; check: A. Beam limiter transistors. B. Brightness and/or color blanking control set too high. . Increasing brightness causes an increase in size and poor focus. A. Weak high voltage rectifier or regulation (high voltage unit).
8-2 10.
11.
12.
13.
14,
15.
16.
17.
18,
19, Small picture and/or poor focus: A. Low B+ voltage (power supply trouble).
Vertical rolling: A. Vertical oscillator transistor, IC, or circuit. B. No sync from logic board.
Horizontal line across center: A. Vertical output circuit is dead (see symptom No. 1. A.). B. Vertical oscillator is not putting out the right wave form. Picture bends: A. Horizontal syne needs adjusting. B. Magnetic or electromagnetic interference.
Flashing picture, visable retrace lines: A. Broken neck board. B. Internal short circuit in the picture tube (arcing). Unsymmetrical picture or sides of picture: A. Defective yoke.
No brightness, power supply operating — No high voltage for the picture tube; check: A. Horizontal oscillator. B. Horizontal amplifier and output. C. Flyback transformer (high voltage unit).
No brightness, high voltage present; check: A. Heater voltage to the tube at the neck board. B. Screen-grid voltage for the tube. C. Focus voltage. D. Grid to cathode picture tube bias.
No high voltage; check: A. For AC input to the “flyback”. B. Horizontal deflection stages. C. Flyback transformer. D. Yoke. E. Power supply.
No horizontal and vertical hold; check: A. Sync transistors and circuit. B. Wires and jack from logic board to the monitor. Wavey picture — (power supply defect); check: A. Transistors, diodes, electrolytic capacitors in the power supply.
21.
23. Moving bars in picture: A. Ground connector off between monitor and logic boards. B. Defect in the power supply (see wavy picture symptom).
Washed out picture (see picture not bright enough): A. Check video signal at the cathode pins with an oscilloscope. If there is about 80 volts peak to peak, the picture tube has weak emission.
Monitor won't turn on: A. Problem in the power supply: Check fuse, transistors, open fusible resistor.
B. Shorted horizontal output transistor. C. Defective high voltage disabling circuit. D. Crack(s) somewhere on main chassis board.
- Can't adjust purity or convergence:
A. Use a degausser to demagnetize tne picture tube carefully following your degausser's instructions. B. Picture tube defective. C. Metal foreign material is in picture tube shield. D. Nearby equipment is electromagnetically interfering. The poles of the earth are pulling off the purity. F. Poor focus or width of picture. m
Guide To Schematic Symbols
THERMISTOR (POLARITY DOESN'T MATTER)
SY YY VW INDUCTOR, COIL, CHOKE (POLARITY DOESN'T MATTER)
(-) CATHODE
- ANODE
ZENER DIODE
8-3 IRON CORE TRANSFORMER (SUCH AS A FLYBACK)
VL
FUSE (POLARITY DOESN'T MATTER)
CATHODE (-)
ANODE (+)
DIODE
COLLECTOR a COLLECTOR Aa
BASE ———> BASE————- EMITTER eianes EMITTER Soong
NPN TRANSISTOR PNP TRANSISTOR
MWv—
VARIABLE RESISTOR, POT, CONTROL RESISTOR (POLARITY DOESN'T MATTER) (POLARITY DOESN'T MATTER)
+ =
LINES ARE CONNECTED ELECTROLYTIC CAPACITOR
LINES ARE NOT CONNECTED CAPACITOR (POLARITY DOESN'T MATTER)
hm = GROUND
Troubleshooting
Troubleshooting monitors requires experience, patience, and luck. The first step is to match the symptom the monitor displays to the diagnosis next to it in the “SYMPTOM-DIAGNOSIS” subsection. This will pinpoint the circuit the problem is probably in, and often the parts to check. Next, the circuit should be visually inspected to see if there are any paris broken, burned, or if something is there that shouldn't be, like a loose screw, etc. Some parts go bad before others and should be checked first. In fact, following is the general order in which parts usually go bad:
- Semiconductors (like transistors, diodes, and integrated circuits). Fusible resistors. Electrolytic capacitors. Resistors. Capacitors and coils. Always remember that a monitor can bite like a snake. Even when it is turned off, capacitors hold voltage and will discharge it to you should you be touching chassis ground. The picture tube or CRT, itself, is a giant capacitor, so avoid the flyback anode plug hole. With the monitor on, the power supply circuit and/or the flyback, which puts out at least 18,000 volts, CAN BE KILLERS! Avoid handling Power transistors (usually output transistors), yoke terminals, and other high power components when the monitor is on.
To maintain the safety and performance of the monitor, always use exact replacement parts. For instance, the wrong components in the power supply can cause a fire, or the wrong color transistor may give a funny color to the picture. Service your monitor on a nonconductive firm table like wood, NOT METAL, and take off all of your jewelry just in case. With all this in mind, you are ready to begin troubleshooting.
Observe the picture carefully. Try to vary the appropriate control that would most likely affect your particular symptom. For example, if there is poor brightness or no picture, try turning up the brightness or contrast control. If the controls have no effect at all, chances are there is trouble with the control itself, the circuit it controls, or a nearby circuit that may be upsetting voltages. Go to the list of symptoms and determine with the schematic where the bad circuit is.
Keep in mind that capacitors hold a charge as can the picture tube (for at least a week and usually longer), and could shock you.
First. check for obvious visual defects such as broken or frayed wires, solder where it is not supposed to be, missing components, burned components, or cracked printed circuit boards. If everything looks good up to this point, make sure that diodes, electrolytic capacitors, and transistors have their leads connected in the right polarity as shown on the schematic and the circuit board.
Turn on the power and measure the voltages at the leads of the active devices such as tubes, transistors, or integrated circuits. Any voltage that does not come within at least 10% to 15% of the voltage specified on the schematic indicates either a problem with that device or acomponent connected with it in the circuit. The next step is to use the ohmmeter to narrow down the field of possible offenders.
To test a transistor, one lead of the ohmmeter is placed on the base; and the other lead placed just on the emitter, then on the collector. A normal transistor will read either high resistance (infinite), or little resistance (400 to 900 ohms), depending on the polarity of this type transistor. Then the leads should be switched, one remaining on the base, and the other switched from the emitter to the collector. Now the opposite condition should result: the resistance should be infinite if it was lower when the other lead was on the base. Consistantly infinite readings indicate an open, and ashortis demonstrated by 0-30 ohms on most of these test readings. Finally, place one lead on the collector, then the other on the emitter. No matter which lead is used, there should be infinite resistance. Any lower reading, Such as 50 ohms (which is typical on a bad transistor), indicates a short. This ali sounds pretty confusing, but a little experience on a good transistor will make you an expert in no time. Usually, the lowest ohmmeter setting is used for testing transistors. Once in a great while a transistor may check out good on this test, but may actually be “leaky” or break down only on higher voltages. If in doubt, change it. Itis also wise to check the transistor out of the circuit just in case some component in the circuit is affecting the onmmeter reading. A diode is tested like a transistor except it only has two leads. Again, there should be high resistance one way and little resistance the other. If it tests bad, take one lead out of the circuit in case some component is messing up the ohmmeter reading.
Without special equipment, integrated circuits are checked by verifying the proper DC voltage on the pins and the correct AC wave form using an oscilliscope. BE CAREFUL: Shorting their pins can easily destroy them. Resistors are checked with an ohmeter and should usually be within ten percent of the value stated on them and on the schematic. You may have to desolder one lead from the printed circuit board. If you wreck the foil on the board, carefully solder a small wire over the break to reconnect the conductive foil. Capacitors are tricky. Their resistance goes up when checked with an ohmmeter which shows acharging action. As they suck up current from the meter, the voltage goes up and so does the resistance. If you are sure a particular circuit is giving you a problem and everything else checks out O.K., Electrolytic capacitors are prime suspects. Substitute a new one and keep your fingers crossed.
Theory of Operation
To understand what goes on inside the monitor, large general groups of circuits will be examined instead of laboriously analyzing the branches and small circuits that make up these groups. This will help avoid confusion and aid in a basic, concrete, knowledge of what makes up a monitor.
THE POWER SUPPLY — The AC going to the monitor from the game transformer is just like the voltage and current from your wall outlet. It jumps up and down going positive and negative sixty times a second. But a monitor needs nice, smooth DC; direct current, not alternating. So diodes chop up the AC and a big electrolytic capacitor filters it out to make it even smoother. Since the monitor is a big piece of electronic equipment, with many circuits demanding a lot of power from the power supply, there are also zener diodes and transistors to help maintain a nice, constant, smooth voltage so that the monitor circuits don't jump around. And this is what happens when you see a wavy picture. There is AC creeping through the power supply, so it must be malfunctioning. If the voltage from the power supply is too low, the other circuits will be starved for power and you may see a small, wavy picture, or noneatall. Some circuits receive voltages that are higher than what the power supply should put out. But they come from the flyback transformer which will be discussed later.
THE INTERFACE SECTION OF THE CHASSIS — The interface section of the chassis is fairly easy to identify. It is right by the place where the video jack(s) from the logic board(s) plug into. There are sets of transistors that receive the separate red, green, blue, and sync information from the cables that come from the logic boards. The circuits jack up the voltage and match impedances, or in other words, prepare the logic board outputs for the circuits that will really amplify them for the output devices such as the yoke in the case of the sync, or the picture tube that shows the colors.
An interesting aside is that our sync is composite negative sync. That means two things:
- The sync is a negative going wave form.
- There are two pulses going at different speeds over the same wire: a. Vertical wave forms at 60 times per second (or Hertz) and b. Horizontal wave forms at about 15,750 times per second (Hz). The sync is amplified by a sync amplifier transistor and sent on its way to the oscillators. The sync or timing information will be explained along with the oscillator shortly. The color information is sent via wires to the neck board where the main amplification occurs. This will also be discussed later.
VERTICAL AND HORIZONTAL DEFLECTION— After the sync signal is amplified by the sync amp, it goes to two different sections, the vertical and horizontal circuits. Basically, the sync signals are for timing so the picture doesn't mess up since it is assembled like an orderly jigsaw puzzle, but so fast that you can't see the electron beams for each color painting the picture on the screen. This will all become clear soon. For now, we will follow the 60 cycle component of the sync as it goes on its journey to the deflection yoke. The 60 cycle pulse goes to the vertical oscillator to make sure this circuit goes back and forth (or oscillates) at 60 times a second. Without this pulse keeping the circuit at the correct speed, it may get lazy and oscillate at 58 cycles or lower, or get ambitious and oscillate at 62 cycles or higher. At the wrong speed, the picture will start to roll up or down. A Wells Gardner 13” (K4806) or 19” (K4906, K4956) color monitor uses an integrated circuit for its sync section. An Electrohome 13” or 19" color monitor uses an integrated circuit 1C501 for its sync section. Wells Gardner uses HA11423 and Electrohome uses HA11244. These ARE NOT interchangeable! The idea is all the same. The output to the vertical amplifying transistors for all monitors must form a sawtooth wave form, sort of like a bunch of pyramids, racing through the yoke’s vertical coils at 60 times a second. Along the way to the output transistors, the 60 cycle pulse is shaped and amplified to do the job: the yoke magnetically pushes the electron beam to fill the screen out sideways looking at the screen with the greatest length going up and down. Or viewing the screen Sitting like a home television set, the amplified vertical output fills the screen up and down. Watching a monitor like this, seeing only a horizontal line means a problem with the vertical coils of the yoke or anything from the vertical output section on back to the oscillator.
8-7 The horizontal section is very similar with a few exceptions. The horizontal wave shape is more like a square and has a frequency of 15,750 cycles a second, Both Wells Gardner and Electrohome use the other side of their respective integrated circuits for the horizontal circuitry. If the oscillator isn't going at the correct speed, the picture may move sideways, start to slant, or tear up with slanted thin figures. With both the vertical and horizontal of all monitors, there are variable resistors that change the speed of the oscillators up and down. This way you have controls that can make the correct frequencies to keep the electronic jigsaw puzzle nicely locked in place. If you're driving inacar and next to you someone elseis driving their car at exactly the same speed, it will appear that they are not moving. And this is why the sync frequency and the oscillator’s frequency must match, so the picture doesn’t appear to move. The correct wave form is shaped and amplified in the circuitry just like in the vertical section. But the horizontal output transistor is a large power transistor and not only serves to give current to the horizontal yoke windings, it also feeds the flyback transformer.
THE FLYBACK TRANSFORMER (OR HIGH VOLTAGE UNIT) — The picture tube needs high voltage to light up, and the power supply can’t meet this demand. The flyback transformer receives current alternating at about 15,750 times per second from the horizontal output transistor. The “flyback” jacks up its input voltage and puts out a higher voltage alternating at the same speed. But, in your “flyback” there are diodes that chop up the alternating voltage to make it a smooth DC output just like in the power supply. This is what goes through that thick red wire to your picture tube. THIS AREA HAS ABOUT 18,000 VOLTS ON IT AND IT CAN KILL YOU! The “flyback” may be dangerous, but it is also generous. It has extra output windings which give voltage to the heater pins of the picture tube, voltage for the vertical deflection circuits, and picture tube screen-grid voltage. So in a way, the high voltage “flyback” is like a second power supply.
COLOR CIRCUITS — The color circuits are pretty straight forward. The signals go into the interface section where some amplification and impedance matching occurs. These circuits are pretty sparse and simple. Each color just has two transistors and a diode with some resistors and capacitors. From here, the AC color signal is sent by wires to the neck board. The color output circuits are on the neck board. The color signals going to the transistors are controlled by two variable resistors called drive conirols. There are only two, one for the red and one for the green.
The blue doesn’t have one. In the emitter part of each transistor is another variable resistor that is the cut off control. These controls vary the amount of amplified AC signal that goes to the cathodes of the picture tube. The more signal, the more color. The bases of each of these transistors are connected together and are all connected to the blanking and beam limiting transistors which are in the interface section. The beam limiter helps control the brightness level, and the blanking transistor rapidly turns the picture tube on and off so that retrace lines don’t show up on the screen. By turning up the brightness on a good monitor, these four to six retrace lines can be seen slanting diagonally across the picture.
PROTECTION CIRCUIT — To protect the high voltage section against voltages that are too high coming from the power supply which could cause X-rays to be emitted from the “flyback”, a circuit senses the higher power supply voltage, and using a transistor, turns off the horizontal oscillator. Since the horizontal oscillator doesn’t work, the horizontal output transistor has nothing to feed the “flyback” which in turn has nothing to feed the picture tube. The monitor will be silent, have no picture, and will appear to be off. But don’t be fooled. There is still that excessive amount of voltage coming from the power supply. To find out, check at pin two of Wells Gardner’s C501 and emitter of X04 for the Electrohome monitor. Here are the voltages you should receive:
Wells Gardner Electrohome 130VDC 120VDC
The best place to measure this voltage on an Electrohome monitor is at a pin marked B1 on the chassis. This is because a 13 inch color Electrohome monitor, The GO7-FBO or GO7-902, has an integrated circuit and very little else in the power supply. Still, there should be 120VDC at B1.
THE PICTURE TUBE (OR CRT) — The picture tube or CRT is an output device. In other words, the end result of the circuit's work is displayed by this part. Actually, the output of other circuits is in the neck of the picture tube. First, there is the heater. The heater boils off electrons from the cathodes so that they (the electrons) shoot up to the screen to excite the phosphors so that the three phosphors emit three colors of light. The cathodes are next, and again they emit electrons to turn on the tube phosphors, making it glow. The cathode can arc or short to the heater resulting in no picture and a defective picture tube. Next come the grids. The first grid is grounded. The following grid is the screen grid which receives about 300VDC depending on the brightness setting. The next grid closest to the picture tube screen is the focus grid which gets about one fifth the amount of voltage that is applied to the picture tube anode.
After jetting from the cathode through all these grids, the electrons speed through a mask, a sheet of material with tiny holes, and then excite the tiny dots of phosphor in the inside surface of the picture tube screen. The green electron gun (or cathode and circuitry) spits out electrons which head for the green phosphors only. The same goes for the red and blue guns, The way the phosphor light blends determines the color seen. Should these electron beams become too intense, they may burn the phosphor. With the monitor off, this can be seen as a dark permanent image of the video information on the tube screen.
Differences Between Monitors
The easiest way to identify the brand of monitor you are working with, assuming you can't find the brand name written on it anywhere, is to check the color of the suction cup type insulator that houses that dangerous anode plug on the CRT. Both monitors use a red wire but the Wells Gardner anode cup is BLACK while the Electrohome anode cup is LIGHT GRAY. Unfortunately, “call-out-numbers” for parts, circuit layout, and even circuit design are similar enough to confuse the average observer. Let's say you have an Electrohome that isn't working. No problem. You can scavenge parts from an old broken up one that you may have around. Now let's say you have a Wells Gardner that isn't working. STOP!! This could bea problem. There are3
8-8 different types of Wells Gardner K4900 SERIES monitors in the games. Here are ways to identify them.
K4906 (1st TYPE) — This monitor's identifying tags have BLACK ink printed on a white background. There is NO Vertical Damping Control. (This Control would be next to the Vertical Hold Contro! but this area is jumpered with a small wire instead. K4906 (2nd TYPE) — This monitor's identifying tags have RED ink printed on a white background. There 1S a Vertical Damping Control next to the Vertical Hold Control. The Damping Control provides a few more lines on the top of the monitor screen (monitor viewed as a normal T.V. would be) for any video game that may need these lines to fit the picture on the
screen. Moving the Control may distort the top part of your picture (or the side, depending onthe game and how the monitor is mounted) so go ahead and move it if you are having this type of problem. To accommodate this new feature, there are a few circuit changes. ONE MAJOR DIFFERENCE BETWEEN THESE TWO VERSIONS OF THE K4906 IS THE YOKE. They look the same but notice the part numbers: K4906 WITHOUT the Damper Control: 2021111201 K4906 WITH the Damper Control: 2021111258 Since the companies like to change part numbers at the drop of a hat, the best thing to do is to request whatever part number is written on your yoke. If you shouid get the wrong yoke, the results will be: Picture distortion. Excessive brightness. Too much or too little vertical picture size. K4956 (3rd TYPE) — This monitor is identical to the K4906 WITHOUT the Damper Controi EXCEPT the picture tube is vertically mounted and there is an additional small P.C. Board mounted on the monitor where the yoke plugs in. This monitor is used on some Cocktail Table games where the picture has to flip for the second player. Generally speaking, some games flip the picture image via the logic board programming but this monitor is used in games that flip the picture image via generation of a small signal voltage which is sent to the extra P.C. Board on this monitor. This signal voltage causes relays on this extra P.C. Board to flip the picture by reversing the horizontal and vertical signals to the yoke pins. What kind of problems can this extra P.C. Board cause? If the relays become defective, the picture won't flip. If the P.C. Board gets cracked you may have a horizontal line on the screen, a vertical line on the screen, or maybe just a dot in the center of the screen. Of course, the logic board could be defective and not sending the signal to flip the picture. In any case, some people feel that using relays is cheaper, simpler, and more reliable, so this is an advantage.
CONTROLS YOU MAY NOT TOUCH Basically, on the Electrohome monitor, you can move any control you want EXCEPT for the B1 control. This sets the power supply voltage (ideally at 120 VDC) and is located right behind VERTICAL HOLD. The 13” Electrohome DOES NOT have this control. It may also be wise not to move the VERTICAL LIN- EARITY since this distorts the picture and is hard to reset perfectly. If you do move it, turn on the Cross Hatch Test Pattern of your game and try to get the squares to the point where they are equal in size by readjusting this Linearity Control. On the Wells Gardner monitor, brightness is adjusted by the “BLACK LEVEL” Control which is right next to the Horizontal Frequency Control. Under the Focus Control is the “SCREEN” Control which youDO NOT touch. Yes, this control does adjust the brightness, but it is used to set the CRT bias and is adjusted at the factory. When Wells Gardner sets it, they mark the Position with a black mark on the knob. If you move it, be sure to realign the mark and THEN set the BLACK LEVEL Control to the brightness you desire. So, other than the SCREEN control, you may adjust any of the controls.
Parts Interchangeability
Some parts can be interchanged on all of the monitors. Here are the rules:
- You CAN swap any resistor between monitors that has the same resistance, wattage rating, and tolerance. You CAN swap any capacitor between monitors that has the same capacitance and voltage rating. You CAN swap many of the parts between the 19" and the 13” versions of each manufacturer's monitor. BUT, be certain to compare the manufacturers’ part numbers to be positive the parts you want to interchange are identical. BE SURE you have read the section DIFFERENCES BE- TWEEN MONITORS which was covered earlier. You CANNOT swap any picture tubes between monitors! In the past you could, but Wells Gardner is now using a new monitor. When
8-9 ordering a replacement picture tube, ALWAYS SPECIFY THE PICTURE TUBE NUMBER! You CANNOT change any part that is a safety part, one that is shaded in gray on the schematic; it MUST be IDENTICAL to the original. To do otherwise IS DANGEROUS. For instance, the 13 inch Electrohome (G07-902) monitor “flyback” looks identical to the 19 inch Electrohome (G07- 904) monitor “flyback”. In fact, there is even a 19 inch Electrohome (G07-905) monitor (which is an obsolete model) with a similar looking “flyback”. NONE OF THESE ARE INTER- CHANGEABLE! You CAN change any of the parts between the G07-904 and GO7-907. They're essentially the same monitor except that the G07-907 has a vertically mounted picture tube. If there is any doubt about what parts can be swapped between each manufacturer's 19 inch and 13 inch models, compare the manufacturer's part number between each one. If they match up, they are the same part.
Power Supply Voltage and Symbols I symbol | Voltage Operating Circuit
® | 15V_ | Vert. Osc. | Sync Blanking ' CRT Cutort
e | wv Horiz. Osc. Horz. Drive Horz. Output Vert. Output
175V_ | Video Output
351 COLLECTOR
1VIDIV 200uSECIDIV 20VIDIV 10uSECIDIV
TP.31 DC COUPLED BOTTOM LINE=0 VDC 44023
2VIDIV 200MSECIDIV
1.C. 301, PINS
1VIDIV SMSECIO' 1VIDIV 20u SECIDIV
TP82 P31, AC COUPLED
20VIDIV SMSECIDIV 1VIDIV 200uSECIDIV
1.C. 301, PIN 13 NEGATIVE SIDE OF C303
1VDIV 200uSECIDIV 2VIDIV SMSECIDIV 19” COLOR MONITOR SCHEM ATIC DIAGRAM
MODELS 19K4901, 19K4906, 19K4951, 19K4956
A
ERVICE TECHNICIA WARNING
“RAY RADIATION PRECAUTION:
ONLY TYPE PARTS SHOWN IN THE
TP81
O.5IDIV SMSECIDIV
+ 28c'b48
- tp (0208
R208 Pal
O.5/DIV 20u SECIDIV
LC. 301, PIN 15 -_ cme ase ——! By, joe SP tin T S8iten OSCILLOSCOPE WAVEFORM PATTERN The waveforms shown are as observed on the wide band oscilloscope with the monitor turned to a reasonably strong signal and a normal picture. The voltages shown on each waveform are the approximate peak amplltudes. If the waveforms are observed on the oscilloscope with @ poor high frequency response, the corner of the pulses will tend to be more rounded than those shown and the amplitude of any high frequency pulse will tend to be less.
82 Bur B/Lex 2SC2068..8/ B8K_ ascisiaavescve serseneeve ascisiasve/eve 2401 2403, RED Our SREEN Our ascecseut SC20EBLBML
"oe I9vitp22 were’) -
Jeno eon a7mineivet
(Corie) [R.CUTOFE] [G.CUTOFF]
- ou Ae
038i oben elie FB A oMET : Rj fe _ P36
Ba hess . Bitty Ye3e2] 7351 ZEl0BK ca are
Haia23
2VIDIV 10uSECIDIV
F
ac i0y agprarsonrnemaen ‘eont
xo cease
1VDIV 2MSECIDIV HOR. OUT 2sve 2808988
weep? 33 a
\) VERT. OUT )esceo73
‘9908 Tera F365 chee. 33K S26¥} ae WER) an wel Lag, Pl | fe 18. |
1; [HOR CENTERING usosricut [HOR CENTERING) 1000P/s00v | 701 + Soo)
Vie =z Biv | onl oe Lisw, jivertout $20
K4901D, K4906D, K495iD 5633 K4956B g-t0
REPLACEMENT PARTS LIST This monitor contains circuits and components included specifically for safety purposes. For continued protection no changes should be made to the original design, and components shown in shaded areas of schematic, or A « on parts fist should be replaced with exact factory replacement parts. The use of substitute parts may create a shock, fire, radiation or other hazard. Service should be performed by qualified personnel only.
MAIN BOARD
| Rel. No. | Part No. | Description | Rel. No. | Part No. | Description |
RESISTORS RESISTORS (CONT.)
| R201 | 203X6500-645, | 1K Ohm, 5%, 1/4W Carbon | R369 | 203X5602-329 | 680K Chm, 5%, 1/2W Comp. | |
| R202 | 203X6500-523 | 30 Ohm, 5%, 1/4W Carbon | R370 | 203X6501-002 | 33K Ohm, 5%, 1/4W Carbon | |
| R203, | 203X6500-405, | 400 Ohm, 5%, 1/4W Carbon | R371 | 203X9014-584 | 1K Ohm, 5%, 1W Metal Oxide | |
| R204 | 203x6700:327 | 100 Ohm, 5%, 1/2W Carbon | 372, | 203X9101-119 | 12K Ohm, 5%, 1W Metal Oxide | |
| R205 | 203X6700-421 | 270 Ohm, 5%, 1/2W Carbon | R375 | 203X6700-763 | 6.8K Ohm, 5%, 1/2W Carbon | |
| R206 | 203x6500-540 | 390 Ohm, 5%, 1/4W Carbon | R376 | 203X9104-404 | 270 Ohni, 5%, 2W Metal Oxide | |
| R207 | 340X2201-934 | 200 Ohm, 5%, 1/4W Carbon | R377 | 203X6500-447 | 150 Ohm, 5%, 1/4W Carbon | |
| 208 | 203X6500-540 | 390 Ohm, 5%, 1/4W Carbon | Rg7B | 203X6500-886 | 10K Ohm, 5%, 1/4W Carbon | |
| R209 | 340X2201-934 | 200 Ohm, 5%, 1/4W Carbon | R379 | 203X6500-886 | 10K Ohm, 5%, 1/4W Carbon | |
| R210 | 203X6500-540 | 390 Ohm, 5%, 1/4W €arbon | R380 | 203X6500-865 | 82K Ohm, 5%, 1/4W Carbon | |
| R21 | 340X2201-934 | 200 Ohm, 5%, 1/4W Carbon | R381 | 203X6500-724 | 2.2K Ohm, 5%, 1W Metal Oxide | |
| R214 | 203X6500-645 | 1K Ohm, 5%, 1/4W Carbon | R383 | 203X9014.387 | 160 Ohm, 5%, 1W Metal Oxide | |
| R215 | 203X6501-126 | 100K Ohm, 5%, 1/4W Carbon | R502 | 203X6500-886 | 40K Ohm, 5%, 1/4W Carbon | |
| R216 | 203X6500-645 | 1K Ohm, 5%, 1/4W Carbon | R503 | 204X 1700-535, | 150 Ohm, 5%, 15W Metal Oxide | |
| R217 | 203X6500-405 | 100 Ohm, 5%, 1/4W Carbon | R504 | 203X9014-267 | 47 Ohm, 5%, 1W Metal Oxide | |
| R218 | 203x8500-645 | 1K Ohm, 5%, 1/4W Carbon | R505 | 203X6501-209 | 2.2K Ohm, 5%, 1/4W Carbon | |
| R219 | 203X6501-126 | 400K Ohm, 5%, 1/4W Carbon | R506 | 203X9104-105 | 18 Ohm, 5%, 2W Metal Oxide | |
| A220 | 203X6500-645 | 1K Ohm, 5%, 1/4W Carbon | R507 | 203X5602-185 | 330K Ohm, 5%, 1/2W Comp. | |
| R221 | 203X6500-405 | 100 Ohm, 5%, 1/4W Carbon | AkRE01 | 204X 1625-058 | 3.3 Ohm, 5%, 10W WW | |
| A222 | 203X6500-762 | 3.3 Ohm, 5%, 1/4W Carbon | R701 | 203X9105-141 | 2.2 Ohm, 5%, 2W Metat Oxide | |
| R224 | 203X6500-189 | 10 Ohm, 5%, 1/4W Carbon | R702 | 203X6206-441 | 2.2 Ohm, 5%, 1/2W Carbon | |
| A225 | 203X6500-169 | 10 Ohm, 5%, 1/4W Carbon | R201 | 204x2070-072 | 2K Ohm-B Semi-Fixed | |
| A226 | 203X6500-169, | 40 Ohm, 5%, 1/4W Carbon | R301 | 204X2070-084 | 5K Ohm-B Semi-Fixed | |
| A227 | 203X6501-044 | 47« Ohm, 5%, 1/4W Carbon | vR303 | 204X2070-055 | 500 Ohm-B Semi-Fixed | |
| A228 | 203X6500-645 | 1k Ohm, 5%, 1/4W Carbon | vR351 | 204x2070-072 | 2K Ohm-B Semi-Fixed | |
| R229 | 203X6700-421 | 270 Ohm, 5%, 1/2W Carbon | VR352 | 204x2070-072 | 2k Ohm-8 Semi-Fixed | |
| R230 | 203X6500-863, | 8.2K Ohm, 5%, 1/2W Comp. | ||||
| R231 | 203X6500-863 | 8.2K Ohm, 5%, 1/2W Comp. | ||||
| R232 | 203X6500-863 | 8.2K Ohm, 5%, 1/2W Comp. | ||||
| A233 | 203X6500-468 | 1/4W Carbon | ||||
| R234 | 340X2820-934 | {V4W Carbon | CAPACITORS | |||
| R235 | 340X2820-934 | 82 Ohm, 5%, 1/4W Carbon | 201 | 203X0014-088 | 1000 uF, 16V, Electrolytic | |
| R236 | 340X2820-934 | , | 14W Carbon | 202 | 202X7200-064 | 330 pF, 500V, Ceramic |
| R301 | 203X6500-508 | 270 Ohm,5%, 1/4W Carbon | C203 | 202X7200-043 | 220 pF. 500V; Geramic | |
| R302 | 203X6500-863, | 8.2K Ohm, 5%, 1/4W Carbon | C204 | 202X7200-043, | 220 pF, 500V, Ceramic | |
| R303 | 203X6500-863, | 8.2K Ohm, 5%, 1/4W Carbon | 6205 | 203X0014-076 | 470 uF, 16V, Electrolytic | |
| R304 | 203X6500-724 | 2.2K Ohm, 5%, 1/4W Carbon | C208 | 203X 1810-149 | 0.1 uF, 125V Myiar | |
| 305, | 203X6500-842 | 6.8K Ohm, 5%, 1/4W Carbon | 207 | 349X2232-109 | 022 uF, 100V Mylar | |
| R306 | 203X6003-201 | 7.5K Ohm, 2%, | 301 | 203X0014-065 | 330 uF, 50V Electrolytic | |
| R307 | 203X6500-825 | 5.6K Ohm, 5%, | 6302 | 203X1600-563 | 0.033 uF, 50V Mylar | |
| R309 | 203X6500-965 | 22K Ohm, 5%, 1/4W Carbon | ¢303 | 203X0629-037 | 3.3 uF, 50V Electrolytic | |
| R310 | 203X6500-988 | 39K Ohm, 5%, 1/4W Carbon | C304 | 203x 1600-366 | 0.068 pF, SOV Mylar | |
| R311 | 203X6500-762 | 3.3K Ohm, 5%, | 1/4W Carbon | C308 | 203X04 12.012 | 22 uF, 16V Tantal |
| R312 | 203X9014-741 | 4.7K Ohm, 5%, 1/4W Carbon | C307 | 203x1600.634 | 0.033 UF, SOV Mylar | |
| R313, | 204X1450-537 | 1K Ohm, 5%, 5W Carbon | C308 | 203X0025-174 | 3,3 uF, 5OV Electrolytic | |
| R314 | 203X8500-481 | 220 Ohm, 5%, 1/4W Carbon | €309 | 203x 1207-100 | 0.068 UF, 100V PP | |
| R315, | 203X6500-169 | 10 Ohm, 5%, 1/4W Carbon | C310 | 203X0629-061 | 10 uF, 100V Electrolytic | |
| R316 | 203X6500-762 | 3.3K Ohm, 5%, 1/4W Carbon | 311 | 203X0041.025 | 10 uF, 160V Electrolytic | |
| R317 | 203X6700-107 | 12 Ohm, 5%, | 1/2W Carbon | 312 | 202X7050-248 | 4000 pF, 500V Ceramic |
| R318 | 203X6500-540 | 390 Ohm, | 14W Carbon | C313 | 203X0040-052 | 47 uF, 160V Electrolytic |
| R319 | 203X6500-645 | 1K Ohm, 5%, 1/4W Carbon | 0314 | 203X1201-265 | 0.033 uF, 200V PP | |
| R320 | 203X6501-002 | 33K Ohm, 5%, 1/4W Carbon | C315 | 203X0629-023 | 1 uF, SOV Electrolytic | |
| R321 | 203x6501-224 | 270K Ohm, | 5%, 1/2W Carbon | C351 | 203X0629-023 | 1 uF, 50V Electrolytic |
| R322 | 203X6500-886 | 10K Ohm, 5%, 1/4W Carbon | C352 | 203x0619-045 | 47 uF, 25 Electrolytic | |
| R351 | 203X6500-886 | 10K Ohm, 5%, 1/4W Carbon | 6353 | 203X1190-015, | 0.0082 pF, 50V Mylar-PP | |
| R352 | 203X6500-785, | 3.9K Ohm, 5%, 1/4W Carbon | C354 | 203X0619-045, | 47 uF, 25V Electrolytic | |
| R353 | 203X6501-085 | 68K Ohm, | 5%, 1/4W Carbon | C355 | 203X 1600-366 | 0.0068 pF, SOV Myiar |
| R354 | 203X6500-762 | 3.3K Ohm, 5%, 1/4W Carbon | 0356 | 202X7050-483, | 0.01 uF, 500V Ceramic | |
| R355 | 203X9205-143, | 6.8K Ohm, 5%, 3W Metal Oxide | C359 | 202X8065-606 | 100 pF, S00V Ceramic | |
| R358 | 203X5601-878 | 56K Ohm, 5%, 1/2W Carbon | C360 | 202X7050-266 | 0.0033 pF, 500V Ceramic | |
| R360 | 203X6500-561 | 470 Ohm, 5%, 1/4W Carbon | C361 | 202X7050-483 | 0.01 uF, 500V Ceramic | |
| R361 | 203X6500-886, | 10K Ohm, 5%, 1/4W Carbon | c362 | 202X7203-032, | 0.01 uF, 50V Ceramic | |
| R362 | 203x9014-645, | 1.8K Ohm, 5%, 1W Metal Oxide | Ae0363 | 2031270911 | 8700 pF, 1.5 KV PP | |
| Ww RIES | 204X1527-751 | 3.9K Ohm, 5%, 7W Metal Oxide | C365, | 20x 1201-265, | 0.33 uF, 200V PP | |
| R364 | 203X6500-246 | 22 Ohm, 5%, 1/4W Carbon | C366 | 203x0019-026 | 22 uF, 25V Electrolytic | |
| R365 | 203x6501.002 | 33K Ohm, 5%, 1/4W Carbon | 367 | 202X8065-162 | 6 pF, 500V Ceramic | |
| R367 | 203X6500-886 | 10K Onm, 5%, 1/4W Carbon | C368 | 202x7203-032 | 0.01 uF, 50V Ceramic | |
| R368 | 203X5602-185 | 330K Ohm, 5%, 1/2W Comp. | 372 | 203X1207-125 | 0.1 uF. 100V PP |
MAIN BOARD (CONT.
| Ret. No. | Part No. | Description | Ret, No. | Part No. | Description |
CAPACITORS (CONT.) SEMICONDUCTORS (CONT.)
| 6380 | 202X7200-087 | 470 uF, 500V Ceramic | 0208 | 200x3181-523, | Transistor (NPN) 2SC1815GR |
| C501 | 203X1810-149 | 0.1 uF, 125V Mylar | 207 | 200X3181-523, | Transistor (NPN) 2SC1815GR |
| 4 C502 | 202X7050-282 | 1500 pF, 500V Cerantic | Q208 | 200X3181-523, | Transistor (NPN) 2SC1815GR |
| 4.0503 | 202X7810-214 | 2200 pF, 125V Ceramic | 209 | 200x3181-523, | Transistor (NPN) 2SC1351GR |
| AC5O4 | 202X7810-214 | 2200 pF, 125V Ceramic | 210 | 200X3181-523 | Transistor (NPN) 2SC851GR |
| C505 | 203x0220.075 | 560 uF, 200V Electrolytic | 0301 | 200X3181-523 | Transistor (NPN) 2SCBS1GR |
| C508 | 203X0040-034 | 22 uF, 160V Electrolytic | 302 | 200X3207-306 | Transistor (NPN) 2SCD73LBGL2 |
| c507 | 203X0041-057 | 47 UF, 160V Electrolytic | Q303 | 200X3207-308 | Transistor (NPN) 2SCD73_BGL2 |
| 701 | 203X0019-092 | 1000 uF, 25V Electrolytic | Q351 | 200X3248-217 | Transistor (NPN) 2SC2482BK |
| 702 | 203X0634-081 | 10 uF, 100V Electrolytic | 0352 | 200X4589-802 | Transistor (NPN) 2SD&98B |
| C703 | 202X7050-248 | 1000 pF, 500V Ceramic | ie301 | 200X2300-033 | IC HA11423, |
A*IC501 200X2600-183 iC STR381 SEMICONDUCTORS
| 2203 | 201X2010-159 | Diode, 1$2076-27 | TRANSFORMERS & COILS | ||||
| 0206 | 201X2010-159 | Diode, 1S2076-27 | L362 | 201X5000-083 | Coil, Horiz. Size | ||
| D207 | 201X2010-159 | Diode, 1S2076-27 | Eat | 811x0004-007 | Coll AD | stor. | Drive |
| 0208 | 201%2010-159 | Diode, 1$2076-27 | zee! | 202% 1300-080 | Tenner ate | ||
| 209 | 201X2010-159 | Diode, 1$2076-27 | ak 1362 | 200x9720201 | —— | ||
| 1301 | 201X2010-165 | Diode, ISS81 | |||||
| 302 | 201x2010-159 | Diode, 1$2076-27 | MISCELLANEOUS | ||||
| D303 | 201X2010-159 | Diode, 182076-27 | AF501 | 204X7120-073 | Fuse, 4 Amp. 125V | ||
| 9304 | 201X2120-009 | Diode, RH-IV | 402 | 206X5008-632 | Recep W Wire 3P-M-BG | ||
| 0305 | 201X2120-009 | Diode, RH-IV | P201 | 204X9600-466 | Plug, PWB 3P-J | ||
| D306 | 201X2010-159 | Diode, 1$2076-27 | P202 | 204X9601-477 | Plug, PWB 6P-Q | ||
| A501 | 201X3120-216 | Diode, RM-1AV | P40 | 204X9600-298 | Plug, PWB 4P-B | ||
| AD502 | 201X3120-216 | Diode, RM-1AV | 501 | 204X9600-249 | Plug, PWB 2P-B | ||
| 40503 | 201X3120-216 | Diode, RM-1AV | 601 | 204X9600-304 | Plug, PWB 4P-C | ||
| A504 | 201X3120-216 | Diode, RM-1AV | ‘THSO1 | 201X0100-112 | Thermistor | ||
| D505 | 201X3120-216 | Diode, RM-1AV | |||||
| 0506 | 201X3120-216 | Diode, RM-1AV | |||||
| D701 | 201X2130-234 | Diode, RU:-2V | FINAL ASSEMBLY PARTS | ||||
| D702 | 201X2120-009 | Diode, RH-1V | AK 88X0138-506 | 19VLTP2? Pix Tube | |||
| 201 | 200X3181-523 | Transistor (NPN) 2SC1815GR | 208X9800-158 | Lateral/Purity Assembly | |||
| 202 | 200X3181-523 | Transistor (NPN) 2SC1815GR | A We 202X1111-201 | Yoke Deflection | |||
| 2203 | 200X4056-260 | Transistor (PNP) 2SA562-Y-TM | 204X9301-255 | CRT Socket | ; | ||
| 204 | 200X4056-260 | Transistor (PNP) 25A562-Y-TM | 291X5004-262 | Automatic Degaussing Coil Unit | |||
| 0205 | 200X4056-260 | Transistor (PNP) 2SA562-Y-TM |
NECK BOARD RESISTORS CAPACITORS
| R401 | 203X6000-729 | 220 Ohm, 5% 1/4W Carbon | e401 | 202X7050-269 | 1200 pF, 500V Ceramic |
| R402 | 203X6500-540 | 390 Ohm, 8% 1/4W Carbon | C402 | 202X7050-248, | 1000 pF, 500V Ceramic |
| R403 | 203X6000-661 | 820 Ohm, 5% 1/4W Carbon | C403 | 202X7050-248, | 1000 pF, 500V Geramic |
| R404 | 203x6000-729 | 220 Ohm, 5% 1/4W Carbon | C404 | 202X7080-282 | 1500 pF, 1.5KV Ceramic |
| R405, | 203X6500-540 | 390 Ohm, 5% 1/4W Carbon | C405 | 202X7050-483, | 0.01 uF, 500V Ceramic |
| R406 | 203X6000-661 | 820 Ohm, 5% 114W Carbon | |||
| R407 | 203X6000-729 | 470 Ohm, 5% 1/4W Carbon | |||
| R408 | 203x6000-998 | 270 Ohm, 5% 1/4W Carbon | SEMICONDUCTORS | ||
| R409 | 203X6000-661 | 820 Ohm, 5% 1/4W Carbon | aso1 | 200X3206-800 | Transistor (NPN) 2SC2068LB |
| R410 | 203X9104-824 | 15K Ohm, 5% 2W M.O. Forming | 402 | 200X3206-800 | Transistor (NPN) 2SC2068LB |
| Ratt | 203x9104-824 | 15K Ohm, 5% 2W M.O. Forming | 403 | 200X3208-800 | Transistor (NPN) 26C2068LB |
| nara | 203X9104-824 | 15K Ohm, 5% 2W M.O. Forming | |||
| 413, | 203X6000-998, | 2.7K Ohm, 5% 1/2W Comp. | |||
| Ra14 | 203X6000-998 | 2.7K Ohm, 5% 1/2W Comp. | MISCELLANEOUS | ||
| RA15 | 203X6000-998 | 2.7K Ohm, 5% 1/2W Comi | 5 | | | |
| Ra16 | 203x9105-154 | 2.2 Ohm, 5% 2W Metal Oxide | aot | alee | nce year |
| P402 | 204X9600-254 | Plug, PWB 3P-A | |||
| R419 | 203X6500-741 | 2.7K Ohm, 5% 1/4W Carbon | Baoa | 304X9600-981 | Plug, Pin 1P-D |
| R420 | 203X6500-741 | 2.7K Ohm, 5% 1/4W Carbon | a | 3704X9601-020 | Plug, PWB 4P-E |
| Rq21 | 203X6500-741 | 2.7K Ohm, 5% 1/4W Carbon | : | ||
| R401 | 204X2115-014 | 500 Ohm, -B Semi-Fixed | |||
| vRdo2 | 204X2115-014 | 500 Ohm, -B Semi-Fixed | |||
| R403 | 204X2115-008 | 5K Ohm, -B Semi-Fixed | |||
| vRao4 | 204X2115-006 | 5K Onm. -B Semi-Fixed | |||
| R405 | 204X2115-006 | 5K Ohm, -B Semi-Fixed |
i ‘Btug ences Rep XI01.X103 and XIOB ViogO AMP 2SCABSC : X102,X104 and XIO6 VIDEO AMP. 25A673C PSR Tae or 7 ‘ or ascisiay
Ex102 sen |
301 x302,x808,x308 NCAMi ‘2SCaS4C or BRCI68S
‘xouwe
X41 POWER DRIVE 25C 2688 % 902 ERROR AMP —2SC1890 een Smee eae
x94 Hbroes ascise BREESE,
—f : |
- =a t Ext | art S507
=
OO-O~-O-0-OI Hare
‘ @ Schematic Notes Unless otherwise specified Resistance: ((2) (K*KQ, M-MQ), 1/4 (W) carbon resistor Capacitance: 1 or higher-» (pF), less than 1-> (yF) working voltage ~~ 50 (V) ceramic capacitor Inductance: ( H) Electrolytic Cap: Capacitance Value (v F)/working voltage (V), IP -= non-polar (or bipolar) electrolytic cap. Refer to the parts list for additional component information.
- — 2 indicates test point connection X701 X-RAY PROTECTOR a ee an : , r 2scasac or 25c16a5 Beeean PBS, escoar ae oh indicates chassis ground unless otherwise specified ACI20V 6OH/50H2 Hz _ indicates cycles per second so% For safety purposes (and continuing reliability) Aa replace all Components marked with safety syrnboi with identical type.
REPLACEMENT PARTS LIST - ELECTROHOME 19”’ MONITOR
Components identified by the A symbol in the PARTS LIST and on the Schematic have special characteristics important to safety. DO NOT degrade the safety of the set through improper servicing.
Abbreviations for Resistors and Capacitors
Resistor Capacitor
| CR | : Carbon Resistor | C Cap. |
| Comp. R | : Composition Resistor | M Cap |
| OM R | : Oxide Metal Film Resistor | E Cap. |
| VR | : Variable Resistor | BP E Cap. |
MFR : Metal Film Resistor
| CMF R | : Coating Metal Film Resistor | MM Cap. |
| UNF R | : Nonflammable Resistor | PP Cap. |
| FR | : Fusible Resistor | MPP Cap. |
PS Cap Tan. Cap. : Ceramic Capacitor : Mylar Capacitor : Electrolytic Capacitor Bi-Polar (or Non-Polar) Electrolytic Capacitor Metalized Mylar Capacitor Polypropylene Capacitor Metalized PP Capacitor Polystyrol Capacitor : Tanta! Capacitor
SERVICE REPLACEMENT PARTS LIST
Symbol Description
Main P.C.B. Ass'y CRT Socket P.C.B. Ass'y Purity Shield Ass'y Part Number SU-1133A SU-3032A 07-220083-03
Outside of the P.C.B. Ass'y Symbol Description Picture Tube 19” A AdDeflection Yoke PC Magnet A AsFlyback Transf. A ASHVR ROS UNF Resistor 2202,25W K C04 C Capacitor 150pF, AC1.5KV X01 Si. Transistor x02 Si. Transistor Sc Screw #8-% sc Screw % x % Pix Tube Mtg. (4) WA Pyramidal Lock Washer (4) Nut Retainer, Pix Tube Mtg. (4) Clip — P.C.B. Support Standoff Wire Terminal (Gnd. Strap) Terminal Lug (Gnd.) Groundstrap Assy. Grounding Spring Wire Hook (Gnd. Strap) Purity Shield Holddown Clamp Support Brkt. RH Support Brkt. LH Chassis Base Yoke Wedge (3)
Purity Shield Ass’y. Parts List
Symbol Description Degaussing Coil D911, D912 Rectifier 1 Amp 600V (2) Pin Terminal (2) Pin Terminal Housing Purity Shield (2 pcs.) Purity Shield (2 pcs.) c911 Capacitor 100nF 10% 400V R921 Resistor, Wirewound 33Q, 4W Fire Retardent Term. Strip 4 Lug
CRT Socket P.C.B. Ass’y (SU-3032A) Parts List
Resistors Symbol Description
| R3105 | v | R |
| R3106 | v | R 200 |
| R3113 | v | R SK |
| R3114 | v | R 5K |
| R3115 | v | R 5K |
| R3116 | OM | R 10KQ2W J |
| R3117 | OM | R 10K Q22W J |
| R3118 | OM | R 10K22W J |
R3119 Comp. R 3.3KQ%W K R3120 Comp. R 3.3KQ%W K 3121 Comp. R 3.3KQ2%W K
Capacitors Symbol Description C3107 E Cap. 10uF 250VA C3108 C Cap. 1000pF DC1400V P
Coils Symbol Description 13101 Peaking Coil Part Number 17-7198-03 A29779-D = 21-141-01 A75034-B = 29-32-01 A29951-B A46600-A QRF258K-221 QCZ0101-005 2SD870 2SC1106A 31-610818-06 31-601418-12 33-255-01 33-494-01 33-629-02 33-670-010R-02 34-228-03 34-33-04 34-574-02 35-212-03 35-3053-02 35-2348-01 35-3890-01 35-3890-02 38-449-02 39-1233-01
Part Number 21-1007-30 28-22-27 34-708-01 34-709-01 35-3847-01 35-3847-02 48-171544-62 42-113301-03 34-492-09
Part.Number QVZ3234-022 QVZ3234-022 QVZ3234-053 QVZ3234-053 QVZ3234-053 QRGO029J- 103 QRGO29J-103 QRGO029J-103 QRZ0039-332 QRZ0039-332 QRZ0039-332
Part Number QEW53EA-106 QCZ9001-102M
Part Number QQL043K-101
Semiconductors Symbol X3101 X3102 X3103
Miscellaneous Symbol A Description Si. Transistor Si, Transistor Si. Transistor
Description ASCRT Socket
Main PCB Ass’y (SU-1133A) Parts List
Resistors Symbol R1406 R1408 R1410 R1414 R1415 R1421 R1422 AFR1401 AR1503 R1504 R1509 R1512 R1514 R1515 R1522 R1523 R1528 R1534 VR1501 41703 AXR1704 AR1901 R1902 R1903 R1904 R1905 4Q1908 4R1909 R1910 AXFR1901
Capacitors Symbol C1301 C1402 C1407 C1414 C1412 C1508 Aci1512 Ac1513 AC1514 C1515 C1520 C1523 C1524 4C1531 Ac1532 1904 C1905 Descripti Vv v CMF OM OM OM Vv AF A\CMF v OM OM om CMF CMF OM OM ZN ZN A\CMF A\CMF AsPosistor UNF CMF OM OM A\CMF Vv ACMF AF D DDVVVVDDD DVUVVOVVVDVDVVVVVVVVUVUIVD jon 2002 2002 6.8Q1W J 3.3K Q1W J 2.7K Q1W J 12KQ2W J 10KQ 68Q2W K 11.8KQ. AW +1% 5KQ 1OKQ2W J B.2KQ2W J 820022W J 8.2Q1W J 4.70Q1W J 68 22W J 390Q1W J
39Q%W +1% 7.68KQ AW +1%
2Q7WK 4.723W J 10KQ2W J 18K QIW J ATQRW +1% 2kQ 2.74K QYAW +1% 220Q'%2W K
Description BPE Tan. E E E PP Na APP App PP BPE E M APP APP E E Cap. Cap. Cap. Cap. Cap. Cap. Cap. Cap. Cap. Cap. Cap. Cap. Cap. Cap. Cap Cap. Cap. . 3.3uF 50V A . 2.2UF 16V K . 4.7UF 6.3V A . 100UF 160V A . 3.3uF 160V A . 5600uF SOV J . 2000pF DC1500V J . 2000pF DC1500V J . 2000pF DC1500V J . 0.53uF DC1200V J . 3.3UF SOV A . 1uF 160V A . 0.1UF 200V K . 2000pF DC1500V J . 1500pF DC1500V J
. 10UF 250V A Part Number 28C1514VC 2SC1514VC 28C1514VC
Part Number A76068
Part Number QVZ3230-002 QVZ3230-007. QRX019J-6R8 QRG019J-332 QRGO019J-272 QRG026J-123Z QVZ3230-014 QRH024K-680M QRV142F-1182 QVZ3230-053 QRGO26J-103Z QRGO26J-822Z QRG026J-821Z QRX019J-8R2 QRX019J-4R7 QRG026J-680Z QRG019J-391 €RZ-C05ZK471 ERZ-CO5DK271 QRV122F-3902 QRV142F-7681 A75414 QRFO76K-2RO QRX039J-4R7 QRG026J-103Z QRG019J-183 QRV122F-470Z QVP5A0B-023E QRV142F-2741 QRH124K-221M
Part Number QEN61HA-335Z QEES1CK-225B QEW51JA-475 QEW52CA-107 QEWS2CA-335 QFP31HJ-562 QFZ0082-202 QFZ0082-202 QFZ0082-202 QFZ0067-534 QENG1HA-335Z QEW62CA-105Z QFM720K-104M QFZ0082-202 QFZ0082-152 QEY0034-001 QEW52EA-106
Coils
Symbol Description Part Number
| Li502 | Linarity Coil | A39835 |
| L1503 | Width Coil | C30380-A |
| L1504 | Heater Choke | C30445-A |
Transformers
| 71501 | Hor. Drive Transf. | A46022-BM |
| T1503 | Side Pin Transf. | C39050-A |
Semiconductors
| 101501 | Ic | HA11244 |
| X1101 | Si. Transistor | 2SC1685(R) |
| X1102 | Si. Transistor | 2SA673(C) |
| X1103 | Si. Transistor | 2SC1685(R) |
| X1104 | Si. Transistor | 2SA673(C) |
| X1105 | Si. Transistor | 2SC1685(R) |
| X1106 | Si. Transistor | 2SA673(C) |
| X1301 | Si. Transistor | 2SC1685(R) |
| X1302 | Si. Transistor | 2SC1685(R) |
| X1303 | Si. Transistor | 2SA673(C) |
| X1304 | Si. Transistor | 2SC1685(R) |
| X1305 | Si. Transistor | 2SC1685(R) |
| X1401 | Si. Transistor | 2SD478 |
| X1402 | Si. Transistor | 2SD478 |
| X1501 | Si. Transistor | 2SC2610BK |
| X1901 | Si. Transistor | 2SC2688 (K.L.M.) |
| X1902 | Si. Transistor | 2SC1890A (E.F.) |
| D1101 | Si. Diode | ‘WO6A |
| D1102 | Si. Diode | ‘WO6A |
| D1103 | Si. Diode | WO6A |
| D1301 | Si. Diode | 18Z473H |
| 01401 | Si. Diode | 18Z473H |
| 01402 | Zener Diode | RD10F(C) |
| D1503 | Si. Diode | HF-1 |
| 01504 | Si. Diode | VOSE |
| D1505 | Zener Diode | RD11E(B) |
| D1506 | Si. Diode | WO6A |
| D1507 | Si. Diode | 1$S81 |
| D1508 | Si. Diode | 18Z473H |
| Ap1701 | AdZener Diode | RD20EV2 |
| 4\D1901 | ASi. Diode | 181887A |
| A\xD1902 | ASi. Diode | 1$1887A |
| AxD1903 | ASi. Diode | 1$1887A |
| \D1904 | ASSi. Diode | 181887A |
| AXD1905 | AdZener Diode | RD6.8EV3 |
Miscellaneous
| ASF1901 | Ause 1.254 | QMF53U1-1R25S. |
| A\F1902 | AXUL Fuse 3A | QMF66U1-3R0S |
REPLACEMEN? PARTS LIST - ELECTROHOME 13”’ MONITOR
Components identified by the A symbo! in the PARTS LIST and on the Schematic have special characteristics important to safaty. DO NOT degrade the safety of the set through improper servicing.
Abbreviations for Resistors and Capacitors
Resistor Capacitor
| CR | : Carbon Resistor | C Cap. | : Ceramic Capacitor |
| Comp. R | : Composition Resistor | M Cap | : Mylar Capacitor |
| OMR | ; Oxide Metal Film Resistor | E Cap. | : Electrolytic Capacitor |
| VR | : Variable Resistor | BP E Cap. | : Bi-Polar (or Non-Polar) |
MF R : Metal Film Resistor Electrolytic Capacitor
| CMF R | : Coating Metal Film Resistor | MM Cap. | : Metalized Mylar Capacitor |
| UNF R | : Nonflammable Resistor | PP Cap. | : Polypropylene Capacitor |
| FR | : Fusible Resistor | MPP Cap. | : Metalized PP Capacitor |
PS Cap : Polystyrol Capacitor Tan. Cap. : Tantal Capacitor
| Symbol | ®Bescription | Part Number |
Main P.C.8. Ass'y SU-1103A CRT Socket P.C.B. Ass’y SU-3016A
Outside of the P.C.B. Ass'y
| Symboi | Description | Part Number |
| Avot | AsPicture Tube | 370ESB22(E) |
| AxDY01 | A\Deflection Yoke | C29123-V |
PC Magnet A76366-A Wedge 30006 A\Flyback Transf, A19183-A
| AR11 | AFocus VR | A46606-A |
| ANROS | UNF Resistor 2202, 25W. K | QRF258K-221 |
| AXC04 | ASC Capacitor 150 pF, AC1.5KV | QCZ0101-005 |
| x01 | Si. Transistor | 2SD869 |
| icot | iC Regulator | STR383 |
| Lot | Degausing Coil | 21-1007-31 |
Degausing Coil Pin Terminal (2) 34-708-01 Degausing Coil Pin Terminal Housing 34-709-01 Groundstrap Ass’y. 34-697-04 Groundstrap Wire Terminal 34-228-03 Groundstrap Spring (2) 35-3560-01
| BR | Support Bracket RH | 35-3919-01 |
| BR | Support Bracket LH | 35-3919-02 |
| sc | SCREW 10-% Pix Tube Mtg. (4) | 31-631018-08 |
| WA | Pyramidal Lockwasher (4) | 33-255-01 |
Clip P.C.B. Support (2) 33-629-02 Ground Lug 34-33-04
| CH | Chassis Base | 38-452-01 |
8-19
XIGI.X103 ond X10S VIDEO AMP 28C484C o, 281683, t Ki02.x106 and X106 VIDEO AM 28A673¢
Fed i gO) || ' mp © To hi ¥
‘escasae or 2sci6es | r |
3304, BL ANning [7 xaos seam uwirer esaer3_ [3e8 x x304 —
1lO3A Mloexi3 RGB Viggo oUTeUT 28caer or 2scislay
Icol ‘Power REGULATOR Sta3e8 SU- MAIN PCB ASSY
BP tte it ee | suelo Sf ¢ [center Ix401, xaoz iE 235i08
Y X50 ORIVE Ol Hour A791 X-RAY PROTECTOR 2ScisO? R'E, 25C2371V 250898 or jae Uf oo cor ve ares (oa fe ” 28¢26N or B8C2608K 250869 ee BBE con ACizOV 6OH2/S0Hr 10%
G07-FBO
00-4147-03 Schematic Notes Unless otherwise specified Resistance: (Q.) (K--KQ, MMQ), 1/4 (W) carbon resistor Capacitance: 1 or higher-> (pF), less than 1 (yF) working voltage > 50 (V) ceramic capacitor Inductance: (v H) Electrolytic Cap: Capacitance Value (v F)/working voltage (V), NP — non-polar (or bipolar) electrolytic cap. Refer to the parts list for additional component information. 2 indicates test point connection ah indicates chassis ground unless otherwise specified Hz indicates cycles per second For safety purposes (and continuing reliability) A replace all components marked with safety symbol with identical type.
Parts identification on circuit boards: e.g. SU1126A (R107 = R1107) SU3030A (R113 = R3113)
Main P.C.B. Ass’y (SU-1103A) Parts List
Realstors Symbol R1406 R1408 R1410 R1414 RI415 1421 R1422 ASFR1401 A\R1503 R1504 R1509 R1511 R1514 R1515 R1522 R1523 R1528 R1534 vR1501 A\R1703 ASR1704 ASRi901 R1902 R1903 Rig04 ASFR1901
Capacitors Symbol C1402 C1411 C1412 C1508 C1511 AC1512 AC1513 AxC1514 C1515 1520 C1524 C1904 C1905 4\C1907
Coils Symbol L1501 L1502 L1503 L1504 L1901
Transformers Symbol 71501 71503 Description vo R 2000 VR 2002, CMF R 6821WJ OM R 3.3KQ1W J OM R 27KQIWJ OM A 12KQ2W J VR 10K2 AF R 68Q2WK ASCMF Ro 11.8KQYUW 1% VR BK OM R 10KQ2W J OM R 5.6K22W J OM R 68022W J CMF R 8201WJ CMF R 4.791WJ OM R 5692W J OM R 390%1W J ZN R ZN R ASCMF Ro 39K QUW +1% ASCMF Rs 7.68KQYAW +1% AsPosistor UNF R 297W K CMF R 5.623W J OM R 10KQ2WJ AF = R 220Q2%WK
Description Tan.Cap. 2.2uF 16V K E Cap. 100uF 160V A E Cap. 3.3uF 160V A PP Cap. 5600pF 50V J E Cap. 47uF 160VA A\PP Cap. 2000pF DC1500V J A\PP Cap. 2000pF DC1500V J APP Cap. 2500pF DC1500V J PP Cap. 0.53uF DC1200V K BPECap. 1uF 50VA M_ Cap. 0.1uF 200V K E Cap. E Cap. 10uF 250VA XMM Cap. 0.1uF AC150V Z
Description Peaking Coil Liniarty Coit Width Coil Heater Choke Line Filter
Description Hor. Drive Transf. Side Pin Transf.
8-20 Part Number QVZ3230-022 QVZ3230-022 QRX019J-6R8 QRG019J-332 QRGO19J-272 QRG028J-123 QV2Z3224-014H QRH024K-680M QRV142F-1182 QVZ3230-053 QRG029J-103 QRG028J-562 QRG029J-681 QRX019J-8R2 QRX019J-4R7 ORGO29J-560 ORGO19J-391 ERZ-C05ZK471 ERZ-CO5DK271 QRV122F-3902 QRV142F-7681 A75414 QRFO76K-2RO QRX039J-5R6 QRG026J-103Z QRH124K-221M
Part Number QEES51CK-225B QEW52CA-107 QEW5S2CA-335 QFP31HJ-562 QEW52CA-476S QFZ0082-202 QFZ0082-202 QFZ0082-252 QFZ0067-534 QEN61HA-105Z QFM72DK-682M QEY0034-001 QEW52EA-106 QFZ9008-104
Part Number A75360-6 A39934 C30380-A C30333-A A39475-J
Part Number A46022-BM 39050-A ae
Semiconductors Symbol (C1501
x1101 x1102 X1103 X1104 X1105 x1106 x1301 x1302 X1303 X1304 X1305 x1401 x1402 x1501 x1701 01101 01102 01103 D1301 01401 01402 01503 01504 01505 01506 01507 01508 AsD1701 AxD1901 AxD1902 4\D1903 4401904
Miscellaneous Symbol ASF1901 ANF1902 Description 1.C.
Si. Si. Si. Si. Si. Si. Si. Si. Si. Si. Si. Si. Si. Si. Si. Si. Si. Si. Si. Si. Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Diode Diode Diode Diode Diode Zener Diode Si. Si. Diode Diode Zener Diode Si. Si. Si. Diode Diode Diode A\Zener Diode ASi. ASi. ASi. ASi. Diode Diode Diode Diode
Description A\Fuse 1A ANUL Fuse 3A
8-21 Part Number HA11244
2SC1685(R) 2SA673(C) 2801685(R) 2SA673(C) 2SC1685(R) 2SA673(C) 28C1685(R) 2SC1685(R) 2SA673(C) 2SC1685(R) 2SC1685(R) 28D478 2sD478 28C2610BK 2SC1685(P-S) Wo6A Wo6A WO6A 182473H 482473H RD10F(C) HF-1 VOSE RD11E(B) Wo6A 18881 182473H RD20EV2 1$1887A 181887A 1S$1887A 181887A
Part Number QMF53U1-1R0S QMF66U1-3ROS
CRT Socket P.C.B. Ass’y (SU-3016A) Parts List
Resistors
Symbol Description
| R3105 | Vv | R 2002 |
| R3106 | v | R 2002 |
| R3113 | v | R 5KQ. |
| R3114 | Vv | R 5KQ |
| R3115 | v | R 5K |
R3116 OM R 10KQ2W J R3117 OM R 10KQ2W J R3118 OM R 10K22W J R3119 Comp. R 3.3KQ2%W K R3120 Comp. R 3.3K2%W K R3121 Comp. R 3.3K Q%W K
Capacitors
C3107 € Cap. 10uF 250V A C3108 C Cap. 1000pF 0C1400V P
Coils
3101 Peaking coil
Semiconductors
X3101 Si. Transistor X3102 Si. Transistor X3103 Si. Transistor
Miscellaneous
a ASCRT Socket
8-22 Part Number QVZ3234-022 QVZ3234-022 QVZ3234-053 QVZ3234-053 QVZ3234-053 QRG029J-103 QRG029J-103 QRG029J-103 QRZ0039-332 QRZ0039-332 QRZ0039-332
Part Number QEW52EA-106 QCZ9001-102M
Part Number QQL043K-101
Part Number 2802611 2S8C2611 2SC2611
Part Number AT5522
IX Schematics and Wiring Diagrams
vibe HNITas
10621 W BEL! FRANKLIN PAEK,ILL GOI! ON THe CT PND AT LIC COT SrowTae aoe BYPASS, BD.
MONIT’ : dy vb
DESIGNATION LIST
DESIGNATION DESCRIPTION
ci-c9 10 MF ax. TANT. C19 470 MF AX. ELEC cu, ci2 470 PF" CER C13-Ci8 100 PRON oH
epi=cpaa IMF AX. CER
RI-RS 1K OHM 1/4 W 5% CRBN
| R4,R7, RO | 470" | . | “ | i |
| R5, RB, RIO | 220 " | :_ | * | * |
| R6, RIL-RI3 | IK" | 7 | ||
| R14, R50,R51,R53,R54 | too" | some | ||
| RIS-RI7 | KO" | ‘ew | ||
| RIG-R2i ,R23-R46 | 2.2K " | = | ||
| R52 | e208" | _ | = | = |
RMI, RW2 | kK 9 Pos SIP
IC 1A, IF 741832 “1B " "08 “ic " " 138 “to “ "B73 “LE, 1H, 1.1K “Das "PLS IM, EN "ey
"2A 741804 “2B “" 368 “ac 07 Xk CUSTOM IC "20 ooxx “ “ 2, 2H,20,2K N58725P “OF 04XX CUSTOM IC “2U,2M,2N 748161
“3A 74LS10 “ 38 " " 66 "3c PROM SPV-1 “30 1 XX CUSTOM Ic “3E —— “3F PROM SPV-2 "3H 74 LS 273 "3g 12 XX CUSTOM IC "3k 7418 378 Bt BP-ROM SPV-3 (SPI-4) " 3M,3N 74 LS 365
Ic aa 74s 74 "4B " "co “4c BP-ROM SPv-4(SPI-6) "40 PAL SPV-5 (SPI-7) " ae BP-ROM SPV-6 (SPI-5) "4k 74.8377 wood 741986 “ag " "20 "4k “8 157 "au "—" 208 "aM, 4n 2148 STATIC RAM
Fel-FB4 FERRITE BEAD
ICS 2C,20,2F 2@ PIN IC SOCKET “ 2E,2H,20,2K,3C 24FIN" 3D,3F ,3J 2epin" " BL 16 PIN" " 40,4E 16 PIN” “4D 20PIN" "
P 50 PIN CONN vt 11 PIN CONN KK-I56 RT ANGLE
PCMHI-PCMHS ScRW
A080 -91435 - C316 SUPER PAC-MAN VIDEO PC. POMH2 + PL +
n20
| A | 8 | c | i} | n | N | ||||
| E | F | H | J | L | M | ai | |||
| Ger. | cee | cra | cra | ops. | cre | cra, | cr10 | opts | — ce |
| Wap | BRR | IRR | WD | RO | Wan PT ee | oan | ~ | WAS |
1 1
| « | ce | cs | ca | |||||||
| S4 | + | + | + | |||||||
| a2 | ‘ | crea | ||||||||
| ceia | os | cris | crie | cri7 | cps | cre | cr20 | ibe | p22 | ores |
| BRR 2B nC | 20 | 2 | oF | 2H | 2s | 2% | en MN | |||
| 2 | zi | 2 | ||||||||
| a | | ics | ies | Ics | Ics | ||||||
| asi — | ICS | Ics | ics | _ | ||||||
| eso | us | wo WG |
ce
| oy | + | ey |
ae nie
| ores | p26 | ur | OnE | cree | crso | cst | cre cpog | cra | cras | cose |
| BR | Be 8 | De Ee | eK |
nis 3 ics
| 'cs | ies | Ics | Ics |
es
| Ra | ans | ca | cs | en | ||
| cra —Seap | wee tras | craz | crea | cosa | eee Ot cree | crar |
| aa Be | aOR | et | ||||
| 4 | Ics. | 4 | ||||
| — | — | R16 — | _ |
ONIGN3d “Lvd O3ANISIU oinuie Tv 09 O4W AVMGIN ATIVE 28619
9ieo-sepie-reov NvwW-Ovd Y3dns Ga ‘Od OSUIA powna
PROJECT ENG J. SZERSZEN [useo on SUPER PAC-MA
| | | T | FULL | [re Red? PER |
oars 1/22/82 ASSEMBLY DWG SUPER PACMAN VIDEO PC. A084- 91435- D316 PART NG
MO5!- 00316 - Qo006 CROSS REFERENCE LIST
| DESCRIPTION | Qty | DESIGNATION, | PART NO. | ||||
| 100 PF AX. CER | 6 | C13-C18 | 0508 - COBO0- 0500 | ||||
| a70PF " | " | 2 | cu-er | 0550-00800-020 | |||
| oMe | 48 | cei-cp4e | 0508 - 00600. C900 | ||||
| i MF AX. TANT | 9 | cl-c9 | 0935- 00814 - 0100 | ||||
| 470 MF AX. ELEC | ' | C10 | 0550 - 00800-1300 | ||||
| 82 OHM 1/4W 5% CRBN | ' | R52 | ©062-!04B3- IXXxx | ||||
| foo " | "oe | 5 | R 14, R50, R5I,RE3,R54 | 0062 -110B3-I¥¥x | |||
| 220 " | "Ne | 3 | R5,R8,RIO | 0062 -133B3-1xKx | |||
| 4700" | = | i | : | 3 | R4,R7,R9 | 0062- | BS IKK |
| bem | om | ome | 10 | RI-R3, K6, RII-R13, | 0062-I79B3-1xx: |
RI5-RI7
| 22k" | "mom | 32 | RIB-R2I,R23-R46 | 0062-19563-) |
R55-R58
| 1k 9 POS SIP | 2 | RMI, RM2 | 0508-00 . 4.0200 | ||
| ©0XX CUSTOM IC | \ | 1c 20 | 066 -001CX-XAPK | ||
| O4xx | =" | ” | : | "OF | 0066 - 003CX-XAPK |
| O7Xx | : | 1 | “2c | 0066 -O06CX- xX AP | |
| (xx | : | 1 | "3D | 0066-O18CX- KAP | |
| xx | oo" | \ | "3s | 0966 -Q|9CX-XAPK | |
| 74 L800 | 1 | Ic 48 | 0300- 00803-0027 | ||
| 74 L804 | 1 | “on | 0300- 00803-0022 | ||
| 74 LS 08 | U | "ots | 0300-00803 -0030 | ||
| 74810 | Hl | "38 | 0300-00803-005! | ||
| 74 Ls 20 | 1 | “ag | 0300-00803-0052 | ||
| 74832 | 2 | “LAGE | 0300 - 006v3 -0031 | ||
| 74.874 | i | “an | 0300 - 00603 -0032 | ||
| 741886 | 2 | “ 3B,4H | 0300-00803-0054 | ||
| 74.8 isa | 1 | "1c | 0300-90803 - 0033 | ||
| 7418 137 | i | “4k | 0300 - 00303-0050 | ||
| 45161 | 6 | “ | MyIN, 2L, | 0300 - 09803-0044 |
2M,2N
| Pats zee | 4 | "TE, | 1H, 11K | 0300- 00803-0046 |
| sate ars | 2 | "10,34 | 0300-00803. 0038 | |
| ts208 | \ | 4t | 0316 -00803 -0019 | |
| oo | 2 | “ 3M,3N | 0316 - 60803-0020 | |
| 4s 368 | 1 | 28 | 0300- 00803-0004 | |
| 7418 377 | 1 | ” ar | : | ai |
| 4 Le sce, | : | 0316 - 00803-0021 | ||
| 1 | 3K | 0316 - 00803 - 0018 | ||
| BP-ROM SPV-6 (SP/-5) | 1 | Ic 4€ | 0316 - 00803-0617 | |
| PROM SPV-i | i | “3c | 0318 - 00803-0014 | |
| BP-ROM SPV-3 (SPI-4) | ' | Io BL | 0316 ~ 00803- 0016 | |
| PROM SPV-2 | ! | “SF | 0316 ~ 00803 ~ 0013 | |
| BP-ROM SPV-4 (SPI-6) | 1 | “ac | 0316 - 00803 ~ 0015 | |
| PAL SPV-5 (SPI-7) | 1 | "40 | 0316 - 90803 - 0012 | |
| N58725P | 4 | Ic 2€,2H,2u,2K | 0508 - 00803 «2200 | |
| 2148 STATIC RAM | 2 | "4M, 4N | 0550 - 90803-6200 | |
| FERRITE BEAD | 4 | FBI-FB4 | 0316 — 00804 ~cox | |
| 16 PIN IC SOCKET | 3 | Ics 3L,4C,4€ | 0508-00804-070 | |
| 20 PIN " | " | ' | “40 | 0550-00804- 2300 |
| 24 PIN ” | ” | 5 | “ 2€,2H,2u,2kK,3C | 0508 -00804- 0500 |
| 28 PIN " | ” | 6 | "20,20, 2F," | 0508-90804-0400 |
30, 3F,3V
| 50 PIN CONN | 1 | Pr | 0300 00804. 1104 | ||
| PIN" | KK-156 | ' | vl | 5 | eran |
| RT ANGLE | * | 3000-16387 -1 | |||
| SCRW | 4 | PCMH ~ PCMH4 | 0316 - 00700 - | ||
| SUPER PAC-MAN VIDEO P.C. | AOBO~ 91435 - C316 | -——— |
CROSS REFERENCE LIST
| DESIGNATION LIST. | DESCRIPTION | Qty | DESIGNATION | PART.NOS. | |||||||||||||
| 100 PF AX. CER | c2 | 0508 -00800-0500 | |||||||||||||||
| DESIGNAT.WN | —_DESCRIPTION. | DESIGNATION | DESCRIPTION | “380 PF | < | tan -ca7 | 0318 -09800-0002 | ||||||||||
| a7 PF | C90 | 9318 -00800- 0003 | |||||||||||||||
| ye | \ | cs | 9880-00800-2400 | ||||||||||||||
| cl | Nov uses | 1c 28 | 7ais74 | 0047 WE | \ | cas | 0550-00800-2200 | ||||||||||
| c2 | loo PF AX CER | 26 | PAL 1OL8 SPC-6 (SPi-1) | a | or MF | 46 | €5-c 24,029, C62 | -C82,c84-287 0808 -00800-0800 | |||||||||
| cs | (ooo PF | oe | apace | Bowe | lowe” | 48 | 26,023.cr. cPas | 0508-00800-0900 | |||||||||
| ca | 22 MF AX | "20 | 2:14 STATIC RAM | c | A | L | 7 | 150 MF AX TANT | 2 | c27,c28 | 0508-00800- i000 | ||||||
| cs-c24 | Ol MF AX | " 2E,2F | 74 Ls 245 | A | 2 | crag? | so | a8 | orm | a7 owe” | 0 | c34-c43 | 0318-00800-0001 | ||||
| 625 | 0047 MF | "2H | 748367 | Pritt | 49 | Res | 220 MF AX, ELECT. | 2 | 64,c30 | 0508- 00800-1200 | |||||||
| c2e | ome | 2u | 74.874 | a | — | a | 4 | co | oo we" | 1 | 32 | 0508 -00800- 1300 | |||||
| c27,c2e | 15 ME AX. TANT. | “2K | 74 LS 248 | me | o | Sm ews. | K | hou | 220 MF“ | IL | c3i | 0808 - 00800-1400 | |||||
| c29 | Cl ME AX. CER | “OM | 74 LS 259 | cee | cos | Cc, | ee | 470 MF | cae | 9550 ~ 00600-1300 | |||||||
| C30 | 220 MF AX. ELECT. | ” 2N | 74 Ls 367 | is | a | a | = | a | £ | ||||||||
| cat | 220 me" | a | F | e | ye | 100 OHM 1/4W 5% CRAN | 6 | Ra6-Ra9 | 9082-11083 - xxx | ||||||||
| 32 | foo wR" | ic 3a | 74 L804 | E | eo om | 330 OHM 1/4W 5% CRBN | 2 | RG, RE | 0062-14483 - 1xxx | ||||||||
| 33 | i | Gp | o BA | Pa neha | . | 470 | 3 | R3,R30,R37 | 0062-156 B3- xxx | ||||||||
| c34-c4as | 47 Me | “3 | 74 Us 32 | val | te os | os | 15 | R2,R4,R5,R10,R13,R14, | 0062-17983- 1xxx | ||||||||
| ea ea | Pr ancen | 3S | a) tee | ics. | es | ves | es | cs | ; | FIG, R19, R29,R31, | |||||||
| C62 - Caz, cB4~ C8 | Meo" | " $e | 74 (S157 | es | . | R32,833,R36,R 39, R40 | |||||||||||
| ceo | we | ” 3F3H | 74 LS 257 | cs | 22K" | . | 6 | R12,R13,R20,R35, R41, | 9062-19583-1xxx | ||||||||
| cao | PF | “30 | 74 Ls 158 | Cw | Ree | ||||||||||||
| en | STATIC/RAM dB I4ecssru.-88 | ew Le | 47K" | ; | 3 | RI,R34, R38 | 0062 - 21183 1xxx | ||||||||||
| ce) eras | LM AX. Cex | oom | Geenow ceocer cee | a | ok * | ni | ' | R22 | 0062 - 22783-ixxx | ||||||||
| : | . | 12K | 1 | RI? | 0062-2318%-ixxx | ||||||||||||
| 3N | 15. XX CUSTOM IC | cs | 5 | cas | mig | C36 | 1967 Baty moway MFG co | ‘ | z | ||||||||
| RI | NoT usED | cria | sor +t oceir™*" Ce" orig + taza | GReT * ALL AiGuYS RESERVED Cre | Be | 3 | Kasi ne? | eee ceee ane | |||||||||
| fp | i ole Aw SeecReN | 7 | as | dls | re | a | a | am | rogeTe ae | oe | 33K | 2 | 2 | R18,R26 | 0062 -25183- IXxx | ||
| RS | 4708 he | Eo | Aa | AR | ae | RR | aA | aS | 47K | an | 2 | RO, R23 | 0064-259 B3- XXX | ||||
| Ra, RS | i | " | " | 1c 4a | 748368 | rook * | " | H | R24 | 82 - 27583 - 1xxx | |||||||
| RE | 33000" " | ” | "48 | 16 XX CUSTOM IC | 2 | ||||||||||||
| RT | NOT USED | ac | 56 XX CUSTOM IC | ics. | |||||||||||||
| RB | 330 | ‘ | * | “ 4€ | 748187 | — | os | ray | —_ | —~ | — | ||||||
| RO | 47K " . | 56XX CUSTOM IC | fan | —_ | — | roy | — | * | kK 9 PINS.LP.8 POS. | 2 | RMI2,RM IS. | 0508-00804-0200 | |||||
| RIO | 1K | 74 L804 | tk OOS | “ 4a" | 1 | RMIT | 0508 -00804-0100 | ||||||||||
| Ru | 47K | " | 74 Ls 08 | cue | oss | 2.2K SPINSIE 4 FOS | 4 | RM4-RMG, RMS | 0316-00804-000 | ||||||||
| RI2 | 22K | ” | 8 | TC 4066 8 | ccm | RS | car | 38 | A0B4-91496-F a 16 | + | ces | 22K%9 | " a” | 2 | RM7, RMB | 0508- 00804-0300 | |
| RI3,RI4 | iK | 74 S273 | p24 | Fata | cree | crer | we a + P30 “pH * cese | P33, | cp 34 mH | 22k 8 | “4 | 4 | RMIO. RMI, RMIS,RM 14 | 0508 -90604-1200 | |||
| Ris | 22K " | : | 3A | 38 | 3. | 3D. | Ed | ae | zr | Bh | Ete | Sh yt | 47K 9 | "8 | 4 | RMI-RM3, RM IE. | 0508- 00804-1000 |
| RG | ‘Kk | 7 | Ic 5N | B 3730 | ~ | ~ | ae | ~ | a | z | |||||||
| RI7 | 2K" | " " | 3 | ||||||||||||||
| nie | bok | . | rei-ros | FERRITE 8€A0 | ff res | 1k onM Por | 1 | ve | 0508-00804.1300 | ||||||||
| R19 | ik | sos | _ | ||||||||||||||
| R20 | a | ns | ies 1A | 40 PIN Ic SOCKET | eae | = | LS | ||||||||||
| © eve in | hee | a | sea | insiae | ' | or | 0508-00801 ~c100 | ||||||||||
| ee | . | ot | c40 | 4s | _ | 2 SUPER PAC-MAN CPU BD. | ay | . | ° | ||||||||
| R22 | ok hom | 8 | . ie | oar | " | + | cer | Scat, cess “EBS SUPER | crap cas | crag | cha | teas | ||||||
| R23 | STK | Po | . | tesa 4a | we, | rm | rd | ar | aL | aM | PrESLIES | a | 0508 - 00802 -0200 | ||||
| Rea | 100 K | ss | ” | 20 PIN | . | 6-28 | ae ae | aA | Ang | 4h | ae th | OA | ; | . | |||
| R 25,827 | 22K | sos | “ 26 | 20 PIN | 7 | ae | 4 LS 04 | Z | Ic 3a,4H | 0300-00803- 0029 | |||||||
| R26 | 33K" "My | ” 3N | 2erin" | 4 | | | me” ieee | B38 | tart oe | ' | “4d | 0300 - 00803-0030 | ||||||
| Re | NoT USED | "43 | 28 PIN | F | a | Be | oy 1882 | ! | rose | 0300- 00803-0031 | |||||||
| R29 | 1K | sos | ” | 4c. 4F | 42PIN" | 1cs | z | a | ae | Rar | 74 La 108 | 2 | "22a | 0300-00803-0032 - | |||
| R30 | 470" | e | "o3u | 16 PIN * | ics | E 1¢s | io | 7a Usise | : | "38 | 0316 -00803.0001 | ||||||
| (R31, | R32, R38 | 1 | 4 | 2a | wae ier | } | vec | 9300. 00803-0033 | |||||||||
| R34 | ark" | J | © PIN KK-I56 STR W/PIN 4 EXTRACTED | sus | co | «( | oo bs 187 | 2 | "38,4 | 0300 - 00803 -0050 | |||||||
| R35 | 22k" " | os | v2 | 2oein * | sg" | san | 2 | + | 748 161 | : | » 3 | 0300 - 00803 -0043 | |||||
| Ane | ix | 4 | "om | 3 | iON | 3 | et? | vrt | ra ceeas | ' | 3D | 9300 -00803-0044 | |||||
| a? | wo tl | “ | a30_ | cir BE | cas | aareuss | 4 | & 2E,2F,2K1F | 0309-00803 -0046 | ||||||||
| R38 | 47K | " | ) | mw | cere | + | oe recee | 2 | " 3F.3H | 0316 -00803 -0002 | |||||||
| R39, R40 | 1K | “oe | Pt | 50 PIN RIBBON CONN. (CABLE ASSY) | — | ke is | | = | cee + oe | ae ees | f | au | 9318 - 00803-0003 | |||||
| R41,R42 | 22k" " | % * | _ | CABLE ASSEMBLY | ae | REO | | | tr | ya | = | ' | “aM | 0300 - 00803 - 9038 | |||||
| Ras | Nor USEO | a3 | Ea | il | & | + | us 367 | ‘ | es1m, 2H, 2N | 0300-00803. 003% | |||||||
| 844 -R49 | 100 | POMHi-PCHMA | 80. spacer | Bz | mae Rae | ot | 74 LS 368 | ' | “an | 0316-00803- co0# | |||||||
| PowHS Po | scRW | @ | aa | ||||||||||||||
| RMI -RMS | 47K 9 PINSLR | wn ene | cao | + | Per | 07 xx CUSTOM 1 | 1 | tN | 088-60 | ||||||||
| RMA RME | zeke" " | MHICSN | MOUNTING HAROWARE | oe | 15 xx" | ' | 3N | eooeck LARS | |||||||||
| RM7, RME | 22k 9 | Ie | “(2) 4-40 HEX NUTS | we xXx | 1 | 4 | 0086 O20ER- XAPK | ||||||||||
| Ratio, amt | aan | "e) won 4125-250" O82 FLT-ST | ae | sles 2slslelelélal | ody | ||||||||||||
| ik 3 | 2) WSH.4 .120-.250- .018 EXT. ST. | BP - ROM | |||||||||||||||
| i | 4 | ow | -RoM | sPC-4 (sPi-3) | ' | ||||||||||||
| awis, Mia | aeK | oy ay eielepore | tesow, | see | : | ie am | 0316 90803-0008 | ||||||||||
| amis | teen | tal lal | al3l8] | $1 815151 sist all | D | secre | ‘c | gale - o0e03- o008 | |||||||||
| . | 47K 9 | . | swi | PB SWITCH | nels | 8 | <| | he | sPc-3 | . | 0316- 00803-9006 | ||||||
| mi | Ks | sw2,sw3 | Pos Dip SWITCH | os | ve | _ | we 3730 | i | 0318 - 00808-0007 | ||||||||
| bows | ‘of | }: | 20) | vl | J peu | MC 6BAOSE CPUC.5MHZ) | 2 | O0s6- 188xx - xxax | |||||||||
| K onM POT | PALIOL8 Spc-6 (spit), | “36 | 9316 - 00803 - coos | ||||||||||||||
| STATIC RAM MBBI48-55/.-55 2 | "3K 3L | 0876 - 00803- co10 | |||||||||||||||
| Te a0eep | : | ae | 0580~ 00803 - 6200 | ||||||||||||||
| oF | Insta | X-TAL 1 | 18.432 MHZ CRYSTAL | 2114 STATIC RAM. | : | 3p | 0508 - 00803 - 5300 | ||||||||||
| <i | 2n33eia | 0508 - 09803 - 0300 | |||||||||||||||
| a | Me 6BAO8E CPUC SMMZ) | —nogg.gig36-F31 | SUPER PAC-MAN CPU BD. | DESCRIPTION | giy | DESIGNATION | PART NOS. | 9 PIN CORN KK- 156 | \ | sy | 2900 - 16367-0910 | ||||||
| 3 | EPROM SPC-) | . | 20PIN " " | 1 | v2 | 3000 - 16387-2015 | |||||||||||
| SPC -i | “ | = | PIN “ “ " | 4 | 00S ~ 16367 ~ ial! | ||||||||||||
| woe | ERROM: SFC 2 | 18.432 MHZ CRYSTAL | H | X-TAL | | 0508 -00804-1400 | IOP | us | 3 | 6367 - 10 |
e 74 Ls 367
| we | 7405 245 | - | ov ao | : | nged.91436- F316 | 50 PIN RIBBON CONN | ' | P | ©300-00804- 1104 |
| iM | 74s 367 | SUPER PAC-MAN CPU BD | CABLE ASSEMALY | \ | - | ‘ag00-00020- 0080 |
0 Nor used
| mk | EPROM SPC-3 | ; | |||||||
| Mc 68AQ9E CPU (1.5 MHZ | : | 0316 - 00804-0902 | MOUNTING HARDWARE | MHICEN | |||||
| rm | MO Oe aE ee teen) | FERRITE BEAD | Fei-Fea | ||||||
| im | fat Ole oa ie | 4-40 HEX NUTS | 2 | - | 0017 -00103-0002 | ||||
| 1 | 16 PIN 1¢ SocKET | ; | cs 3M | 0932-0081 7-0100 | 4-40 X8 SLT PAN M.S | 2 | - | 0017- 00101-0810 | |
| 4 | ~~ | 20 PIN IC SOCKET | 2 | ICS IM,28 | 0550-00804-2300 | WSH.4 125- 250-032 FLTST. 2 | - | 0017- 00104-0015. | |
| wut ENG J. SZERSZEN | 2 ONSUPER PACMAN 24 | MIDWAY MFG. CO. | 2apin™ | * | 1 | ok | 0808-00804-0500 | WSH.4.120--250- O18 ExT sT. 2 | - | 0017- 00104-0071 |
| mo | FULL [Mo REI | DER | PnANKLIN eK 1 | 28 PIN | 5 | 1B,1C, IN, | 0508-00804 -0400 | PC BD SPACER | a | os16 ~co706-00xt |
| - | Fut | . | 3N,48 | scaw | 4 | 0u17 - 0010! -0335 | |||
| ASSEMBLY OWG | | TNO | 40 PIN" | 2 | “AIL | 0508-00804- 1800 | ||||
| SUPER PAC-MAN CPU 8D. | - | - | 42 PIN” | “ | 2 | “ 4C ar | 0508 -00804- 1900 | ||
| AGHA 81436. Fa16 | | MOSI- 00316 - F008 | PB, SWITCH | ow | 500 -90804-< | a9 | ||||
| me | 8 POS. OIF swiTce | 2 | sw2, SWS | 990-008 |