CATHODE RAY TOMES

Centipede Caberat DP-189-3rd-02A

Centipede (revision 4) (Atari, 1980) · Drawing Package · 1 pages · original scan

Page 1
Scan of page 1

Centipede Playfield RAM Testing the Playfield RAM

From MPU 1, Perform the CAT Box preliminary setup. 3 Address Bus

Sheet 1, Side 8 2. Set the CAT Box switches as follows:

ross TESTER RESET DBUS SOURCE TO ADDR BYTES to 1024 4 IW MODE to (OFF) RAW to WRITE. Key in 0400 Set FIW MODE to PULSE, then to OFF. FAW'to READ ‘Set RIW MODE to PULSE, then to OFF.

TolFrom MPU. ‘Data Bus Shoet 4, Side 8

From Syne

Sheet 1, Side B

Playfield Address Selector

‘The Playfield Address Selector controls the access tothe playfield memory. Itallows either the game MPU or the sync generator to scan the playfield mem ‘ory. The Playfield Address Selector consists of multiplexers P5, and P7 and ‘gate Ka

When 3H on pin 1 of PS and P7 is low and pin 15 on P7 is low, the Playfield ‘Address Selector receives 8H, 16H, 32H, and 64H on PS and 18V, 32V, 64V, and ‘¥28V on P? from the sync generator. These signals enable the sync generator circuits to access the playfield memory

When 2H goes high the game MPU addresses the playfield memory via 'AB0-AB9) for the positioning ofthe graphics. During horizontal blanking (pin 15 (0 P7 is high) the outputs of P7 (PFA&PFA7) are held high enabling the motion object circuitry to access the playfield memory for the motion objects to be displayed, If the CAT Box reads an address that doesn't compare, the COM- PARE ERROR LED lights, the ADDRESS/SIGNATURE display shows the failing address location, and the ERROR DATA DIS. PLAY switch is enabled,

If the COMPARE ERROR LED does not light, rekey 0400 and re peat the test with the DBUS SOURCE switch set to ADDR. This fensures that the data bits at address 0400 will go high. if the ‘COMPARE ERROR LED does not light after this step, the Play field RAM is good.

picture data PROM circuitry

Playfield Multiplexer

Consists of select multiplexers KE, L6, M6, NG and PS.

\When 256H is low and 4H is high, AB4 and ABS from the MPU address bus is the selected output from PB. This output is applied to multiplexers K6, L6, M6, and NE {as select inputs. When the MPU is accessing the playfield code muitiplexer, the Playfield data is elther being read or updated by the MPU. When 256H is high and 4H fs low, the inputs from the syne generator (128H and 8V) are the selected outputs. ‘These signas then select which bits of data PFDO-PFD31 are sent out via K6, L6, M6, and N6 for the playfield codes that eventually are displayed on the monitor. ‘The playfield codes (PFO-PF7) are latched by JS and J6 to the MPU data bus (J5) ‘and to the picture data PROM circultry J6). When PFRAI Syne generator goes high, the inputs on J6 (PFO-PF7) are latched out to the MPU via (080-087. When 4H on pin 11 of J6. goes high, the inputs (PFO-PF7) are latched to the is low and 1H from the The Playfield Multiplexer receives playtield data trom the playfield memory Sombie, | i<et¢—_————————— (PFDO-PFDS!) and the output (PFOPF7) is a code that determines what Is 1) dis ne played on the monitor, of 2) read or updated by the MPU. The Playfield Multiplexer shove Side 8

A, -- ATARI

Sheet 2, Side A

Centipede”

Playfield Memory Playfield Multiplexer From Syne Picture Data ROM Circuitry Sheet 1, Side 8

Sheet 2, side A P80-02 Sr print ContipederCabaret Motion Object Circuitry (Vertical) Motion Object Circuitry (Horizontal)

Section of 037241-01 H Motion Object Circuitry (Vertical)

‘The Motion Object Circuitry (vertical) receives playfield data and vertical inputs from the syne generator circuitry to generate the vertical component of the motion object video. PFOB. 4 from the playfield memory and 1V-128V from the sync generator are compared at FB and H6. The output Is gated by A7 when a motion object is on one of the sixteen vertical lines and is latched by E6 to AND gate 87. A low on B7 pin 8 indicates the presence of a motion object on, Cone of the vertical lines during non-active video time. This signal (MAT3H) enables the mult plexers in the picture data citcuity

When 256H on pin 1 of D7 goes high, 1V,2V, V and PICO are selected When 256H goes low, the latched output of £6 is selected. The output of D7 is EXCLUSIVE OR gated at E7 and is, sent to the picture data selector circuitry as motion graphic address (MGAO-MGA3). The other input to EXCLUSIVE OR gate E7 is PICT from the playfield code mutiplexer circuitry. PICT ‘when high causes the output of £7 to be complimented. For example, Il MGAO-MGAS are ow, PIC7 causes MGAO-MGAS to go high. This causes the motion object video to be inverted top to bottom, .

‘Sheet 1, Side 8 Motion Object Circuitry (Horizontal)

The motion object circuitry (horizontal receives playfield data and horizontal inputs from the syne generator circuitry. PFD16-PFD23 from the playfield memory determine the horizontal position of the motion object. PFD24.PFO29 from the playfield memory determine the indirect ‘Color of the motion object. PFD16-PFO23 are latched by Land loaded into the horizontal pos tion counters AS and B5 by a low on pin 9. The horizontal position counters then address video RAMS A6 and BS. These RAMS are loaded with the video data forthe particular motion object from shift registers H9 and J9 (which were loaded from the graphics ROM). The output for RAMs A6 and 86 Is then sent to the color PROM circuitry as MRO and MRI.

From Syne Generator Picture Data ROM Circuitry

‘The picture data ROM circuitry receives picture Information, assigns a color code tothe information ‘and sends ito the color PROM circuitry. The picture ‘ata ROM circuitry consists of ROM devices F? and HN7, multiplexers F8, H8, J8, KB, shift registers HO ‘and J9, and latch 8.

The picture ROMs receive (PICO-PICS) from the playfield code multiplexer, MGAO-MGA3 (motion graphics address) trom the motion object circuitry, 256H and 256A from the sync generator. PICOPICS represent the code for the object to be displayed MGAO-MGA3 set one of eight different combina tions of the ine by Bit blocks of picture video or the 16 line by 8 bit Blocks of motion object video. 256H when high selects the playfield picture col or codes to be addressed. 256H when low selects the motion object color codes to be addressed. The picture data ROM output 01-08 on F7 and HIN? are ‘multiplexed by F8, H8, J8 and K8 and shifted out ser lally at H9 and J9. This serial output Is latched by F9 ‘as AREAO and AREA to the motion object horizon tal circuitry and the video output circuit.

Nate Doe To OTA Reser Om esac Dowswr Rencn Smeaser Te ary