CATHODE RAY TOMES

Red Baron Sit-Down DP-171-1st-03B

Red Baron (revised hardware) (Atari, 1980) · Drawing Package · 1 pages · original scan

Page 1
Scan of page 1

Auxiliary Board Address Decoder

__PROM AS is the address decoder for the Red Baron"™Auxiliary PCB. When TO on pin 13 is low, the address decoder PROM AS is enabled anc receives: [EAB3-EAB6 from the game address decoder. When ER/WB is low, AS en the appropriate creuity on the auxiliary boar, via decoders BS, and gates

Math Box

during signature analysis EPEFERERT 13;

:

EP EFEPER)

from sree? praenan-:

  • At sonatas with an asterisk ar akan wit 1K ohm pull ‘Op resitorsttached between the signature anlyzr dela probe end + 8 VDe.

‘a rerla

Ten

Potsel Circuitry

Horizontal (H POT) and Vertical (V POT) inputs from the

Joystick are applied to analog switches J. When POTSEL Of the signal, A3 and B3 count up or down. This count is ‘This current is converted to a voltage at KS pin 1 and is

from data latch E3 goes high, H POT passes to KS pin 12 ‘and compares with the output from KB pin 1. The result is applied to counters A3 and 83. Depending on the polarity

‘applied to DAC B4 as PO-P7 and the custom audio and Control chip B2. The output of DAC B4 Is an analog current equal to the digital Input from ‘AS and B3. com

‘sont to comparator KS pin 13. When POTSEL goes ow, V

POT passes, and the circuit works as explained for H. Por.

Audio Output

Shift registers E4, F4, and gate H4 function as a ran. dom noise generator. The output on Fé pin 13 is gated with CRSH4-CRSH? to produce BANG,and with SHOT to produce SHOT SND.

CRSH4.CRSH7 and RNOISE are gated at F3 and the output is a digital crash signal. This signal is summed by resistor network R14-R17 and applied to comparator K& pin 6.

A. ATARI

Sheet 3, Side B RED BARON™

Auxiliary PCB Audio Output Control Panel Input

Section of 036305-01 A

‘Sheet 3, Side B 171.03 1st printing ioe

When OL goes high, €3 latches the MPU data (ED80- EDB7) for CRSHO-CRSH7, SHOT and SQUEAL sound in ts, and the start LED and POTSEL signals. When

The High Score Memory circuit stores the three best ‘scores and other pertinent information, These scores are ‘saved even if power is removed from Score Memory circuit consists of an ‘mable ROM CO, tches AO, HO, FO, buffer EO and timer JO. 40 produces a 12 KHz 0-16V square wave. This signal when +15V forward biases diode CRT and allows capacitor C54 to Charge to ~ 28V. When the signal is OV, CR7 Is cutoff and CRB is forward-biased wh ‘charges to approxim: for EAROM 0 to operate, ‘causes C53 to develop a charge. C53 = 28V. This Is the potential required ‘The MPU addresses the EAROM (ABO-ABS) via latch AO, when EAROMWR is high. Data is latched into the EAROM on EDBO-EDB7 through latch FO.

‘The function of the EAROM (read, write or erase) is determined by the MPU. on data lines EOBO-EDB3, Latch HO re ‘ceives a high EAROMCON signal from the MPU address de- ‘coder and function data is passed to the EAROM.

Data In the EAROM is read by the MPU when the EAROMIAD signal to buffer EO goes low. The EAROM is addressed by the MPU after a reset pulse or during Self-Test. ‘on pin 1 goes high, the output of E3 s cleared. Aisne us

‘The custom audio and control chip B2 generates most ‘of the audio for the Red Baron™ game. It also serves as the data buffer for the POTSEL input to the MPU.

When low, AGHPEN enables the custom audio chip £82. The clock frequency of ERIWS determines whether ‘data is written into the chip or read from the {rom the POTSEL circul, represents steering ip. POPT, formation from the game joystick. This is buffered and latched to the MPU when addressed by address lines EABO-EABS. ‘The audio output from B2 is also selected by addressing EABO-EABS from the address decoder. SHOT SND, BAND, SQUEAL SND, and the custom audio output are summed at resistor network RB-AI1 and applied to pust-pull amplifier Ké. The output is AUDIO | ‘and AUDIO Il.