Operation Wolf 3
Operation Wolf 3 (World) (Taito Corporation Japan, 1994) · Manual · 26 pages · 22 sections · original scan
T/iT Oo
TAITO AMERICA CORPORATION 390 Holbrook Drive Wheeling, IL 60090 Telephone: (708) 520-9280 Fax: (708) 520-1309 ©TAITO CORP. 1994
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
OPERATION
WOLF 3
TABLE OF CONTENTS
| Introduction: Game Inspection a 1
‘specHications; kara rtnsnazeavstgiseczies 2
Game Installation iucessesestersssertenevnes 3
Play Instructions iduecseseseeetstseseseneeee 3-4
Test and Switch Settings saucssscsesssestenesenereee 5-11
Dip Switch Settings (—avtectsesesesestenenenss 8
FrontReplacement Parts vccssssssssesesesestevens 12
Rear Replacement Parts 13
|Gun Assembly Parts i istessesestesesseseenennens 14-17 Test of Connector Terminals vessssssestessteseerteens 18 | Power Wiring Diagram iiiucecsestetereenesesertene 19 |
|Transformer Chart aacessesssessnessnesnnenene 19 |
| Pwr. Supply Switcher Assy. /JAMA —vvcecscesesessesseseesenes tock
ThiTO TAITO AMERICA CORPORATION 390 Holbrook Drive Wheeling, IL 60090 — , aa Telephone: (708) 520-9280 Taito” and Operation Wolf 3 Fax: (708) 520-1309 are trademarks of Taito Corporation.
LE =f- °; |
INTRODUCTION
Game inspection
Please take a moment to read the following before turning on your new Operation Wolf 3™ for the first time. Your game was carefully checked at the factory before shipping.
After removing the game from its carton inspect the game carefully. Look for cracks in the cabinet, gouges, bent metal parts, etc. This shipping damage should be reported to the carrier. Remember to take photographs.
Precautions concerning the place of installation
This is an indoor game machine. Absolutely do not install it outside. Even indoors, avoid installing in places mentioned below so as to ensure proper usage:
« Places subject to rain or water leakage, or condensation due to humidity. In the proximity of an indoor swimming pool and/or shower. Places subject to direct sunlight. Places subject to heat sources from heating units, etc., or hot air. Vicinity of highly flammable/volatile chemicals or hazardous matter. Sloped surfaces. Vicinity of anti-disaster facilities such as fire exits and fire extinguishers. Places subject to any type of violent impact. Dusty places. Residential environment - (See F.C.C. statement which follows).
F.C.C. Requirements
The Federal Communications Commission requires that all Class A equipment be verified and labeled as follows:
This equipment complies with the requirements in part 15 of FCC Rules for a Class A computing device. Operation of this equipment in a residential area may cause unacceptable interference to radio and TV reception requiring the operator to take whatever steps are necessary to correct the interference.
This label must be permanently attached in a conspicuous location and the text must be legible. If this label is removed or tampered with such action is punishable under Section 503 of the Communications Act of 1934 (ACT), as amended.
_—k_ @-@&7; °°, °°.
SPECIFICATIONS
Power Line: 115V AC 60Hz Consumption: 250 Watts (approximately)
Cabinet Height: 72-3/4"" (As assembled) Width: 26-5/8”" Depth: 36-5/8”" with 15-7/8” additional pedestal
SS
GAME INSTALLATION
Operation Wolf 3™ comes fully assembled. To properly install the game, follow these steps:
1, Uncrate machine. 2, Attach leg levelers to bootm of pedestal. Level game. 3, Plug into grounded electrical outlet.
ATTENTION
Each day the Operator should check that | ALL warning labels are legible and affixed to this equipment in their proper locations. |
PLAY INSTRUCTIONS
Operation Wolf 3™ is a game played as long as civilian lives are not alll lost. You get an unlimited number of bullets, but when alll civilian lives shown on the screen are lost, the game is over.
The gun is the basic control. It can fire both bullets and bombs. Here is how to use the guns:
FORE-GRIP: Bomb Attack Bombs can be used up to the number of stocks. Bombs are supplied depending on scored points in each cleared scene. MH
TRIGGER: Bullet Fire
If the trigger is pulled continuously, bullets run short and the rapid-fire becomes slowed. When you release the trigger, more bullets are supplied.
a
Play Instructions continued
Here is a screen layout with an explanation of the symbols you'll see on the screen :
DISPLAY OF PLAYER'S LIVES
SS SaaS
WHEN LIVES HAVE BEEN LOST, THE GAME IS OVER, SCREEN LAYOUT
THE NUMBER OF BULLETS IF THE TRIGGER IS PULLED CONTINUOUSLY, BULLETS RUN SHORT AND THE RAPID-FIRING BECOMES SLOW. BY RELEASING DISPLAY OF “BOMB” STOCKS THE TRIGGER, BULLETS ARE SUPPLIED.
‘BOMBS” CAN BE USED UP TO THE NUMBER OF STOCKS.
Other ammo is available when you shoot the colored boxes.
DON’T SHOOT CIVILIANS. TAKE ITEMS. spe eatin
IF THE PLATER SHOOTS CIVILIANS, POINTS ARE DECREASED ITMES CAN BE TAKEN BY SHOOTING ITEM BOXES.
4u-CALIBER BULLETS AAR EEIE ian
GB, SHOTGUN ae < ) WIDER suor EFFECT
GRENADE LAUNCHER
Test AND SWITCH SETTINGS
To start the testing procedure, open the coinbox door to access the test switches on the unit:
O
VOLUME ADJUSTMENT ON MAIN CPU BOARD | SERVICE
When the test switch line of the G-connector No. 15 is connected to the GND, the game mode is discontinued and the “Test Program” screen is displayed.
To select a specific test, pull the trigger of a gun. The mode is highlighted on the screen. To start the test, press the 1P start button.
To end the test mode, select “EXIT” and press the 1P start button.
TEST PROGRAM (8/21 12:00 VER 2.31 J)
GUN POS SET LEVER CHECK COLOR CHECK SOUND CHECK DIP SWITCH TIMER SER
- RAM CLEAR -8- HIGH SCORE RESET -9- FACTORY SETTING -10- ACTION TEST PUSH START BUTTON
Son one
1 P START BUTTON
2P START BUTTON
Test No. 1: Gun Position Setting Test
Set the position of the 1P gun as follows:
- Onscreen A adjust the gun to the + mark located in the upper right side of the screen and pull the trigger.
- Onscreen B adjust the gun to the + mark located in the lower left side of the screen and pull the trigger.
Set the position of the 2P gun following steps 1 and 2 above. When the adjustment of the 2P gun is finished, the screen returns automatically to the “Test Program” screen.
SCREEN A SCREEN B
PLAYER] X.Y MIN SET PLAYER] X.Y MIN SET PUSH GUN BUTTON PUSH GUN BUTTON
SET X = 00 SET Y = 00 SET X = 00 SET Y = 00
Test No. 2: Lever Check
Do the input test for each switch as follows: Press each switch. If it is normal, the color of the letters changes.
PUSH A+B BUTTON LEVER TEST
2P UP.
LEFT = RIGHT LEFT RIGHT DOWN DOWN
BUTTON A COIN Sw BUTTON A
BUTTON B SERVICE sw BUTTON B
BUTTON C BUTTON C
When the trigger and the fore-grip are pulled at the same time, the screen returns to the “Test Program” screen.
a
Test No. 3: Color Check Test
Check the color adjustment and size of the monitor as follows:
When the trigger is pulled, the screen changes from the color bar screen to the crosshatched screen. Push the 1P start button to return to the “Test Program” screen.
(COLOR BARS) (CROSSHATCH)
aa |
Test No. 4: Sound Check
Check the sound outputs as follows:
« Pull the trigger to advance the selection iterns, and use the fore-grip to change the numbers ¢ Press the 1P start button to select the item, then press the 2P start button to test the sounds you have selected.
PUSH A+B BUTTON
SOUND CHECK
| BGM | DATA | 00 |
| SE | DATA | 00 |
| SE2 | DATA | 00 |
Pull the trigger and the fore-grip at the same time to return to the “Test Program” screen.
eee ss Test No. 5: Dip Switch
Test the DIP switch settings as follows:
e Use the fore-grip to select the switch to be changed. Use the trigger to select “ON” or “OFF” settings. « The contents fo the selected switch are displayed on the lower left side of the screen.
DIP SW A (FOR NORTH AMERICA)
Contents of settings of DIP SW-A
e Screen rotation: The screen is inversed. « Attract sound: Decides whether the attract sound is activated. e Play pricing: Decides the number of coins per play. « Buy-In Play pricing (North America only): Sets the continue play fee.
Contents of settings of DIP SW-B
« Game difficulty: sets the game difficulty levels. e Life: sets the number of lives at start of game. « Blood: decides whether to activate bloodletting when men are shot during play.
a
Test No. 6: Timer Setting
Set the present date and time as follows: « When the 1P start button is pressed, the items move. When you pull the trigger, the value of the color-changed item advances. Pull the fore-grip to return to the original value. « When you've finished with the settings, press the start button to implement the change. The settings will not change without this step.
TIME SET PROGRAM
| DATE | - | 94/8/21 |
| WEEK | - | SUNDAY |
| TIME | - | 12:25:48 |
| DATE | - | 94/8/21 |
| WEEK | - | SUNDAY |
| TIME | - | 14:25:48 |
Pull the trigger and the fore-grip at the same time to return to the “Test Program” screen.
a
Test No. 7: RAM Check
Initialize the back-up RAM as follows:
- Pull the trigger to select YES or NO on the screen. Initialize it by pulling the fore-grip. Your selection will not be implemented if you do not pull the foregrip.
- Press the 1P start button to return to the “Test Program” screen.
RAM CLEAR PUSH START BUTTON RAM CLEAR PUSH START BUTTON
BACKUP RAM CLEAR NO BACKUP RAM CLEAR YES
rr
Test No. 8: High Score Reset
Clear the high score as follows:
Pull the trigger to select YES on the screen, then press the 1P start button to reset the high score.
When the 1P start button is pressed, the screen returns to the “Test Program” screen,
Test No. 9: Factory Setting Check
Factory settings are listed on page 8 of this manual. This screen returns all settings to the factory settings as follows:
- Pull the trigger to select YES if you want to return all settings to the factory settings. Confirm your choice by pulling the fore-grip. No changes will occur if you do not pull the fore-grip.
- Press the 1P start button to return to the “Test Program” screen.
FACTORY SETTING
ARE YOU SURE? YES NO
PUSH START BUTTON
Test No. 10: Action Test
Select this test to enter the gun action test.
ACTION TEST WAIT
TIMER 0:0:21 COIN_COUNT 9
PUSH START BUTTON
When the 1P start button is pressed, the screen returns to the “Test Program” screen,
FRONT REPLACEMENT Parts
Seq. Description Part No.
| 1 | CRT Glass 19X25X21.6 | NX-00001 | |
| 2 | Speaker, 4” | 5555-13961-00 | |
| 3 | Flourescent Light Assy. | A-15890 | |
| 3a | Flourescent Light | H-16303 | |
| 4 | Clear Glass | 08-7456-4 | |
| 4a | Screened Marquee | ZA-00014 | |
| 5 | Push Button - Red | 20-9687-1 | 1 |
| 5a | Push Button - Blue | 20-9687-3 | 1 |
| 6 | Coin Door | Ny-00001 | 1 |
| ai | Mat, 16” Black Ribbed | NP-00002 | 1 |
| 8 | Gun Assy. | M90 03480A | 1 |
| 9 | 25” Mirror | 31-1900 | 1) |
| 10 | Instruction Decal (on Monitor Glass) | 1 set |
—_—L_o'“"“"“_ .}.} ©
REAR REPLACEMENT PARTS
| Seq. | Description | Part No. | Qty. | ||
| 1 | 25” Color Monitor | 5675-12787-05 | 1 | ||
| 2 | Transformer | 7 | 5610-13829-02 | - 1 | |
| 3 | Switching Regulator Power Supply | 20-9920 | [oo | ||
| 4 | [Main CPU Board Assy. | M43T0297A | i | ||
| 6 | Diode Bridge | : | | | 5100-09418-00 | 1 |
Gun AssEMBLY # 1
S/A No. M90 03480A
Description Grip A ~ F90 3624B LLL @2 «@ °@X&° @X~€72€«2«7°7 °; ;
| Grip B | F90 03625B | 2 | |
| Gun Body A | F90 036228 | 2 | |
| Gun Body B | F90 36238 | 2 | |
| Slide Grip Base | £30 086218 | 2 | |
| Slide Grip A | ' | F90 03626A | 2 |
| |Slide Grip B | F90 08627A | 2 | |
| Base Cover L | £30 08622A | 2 | |
| Base Cover R | #30 08623A | 2 |
Gun AssemeLy # 2
Seq. Description Part No. Qty.
| ‘t | Mask | F90 02522A | 2 | ||
| 2 | ‘Sub Shaft | £10 00880A | 2 | ||
| 3 | Side Bracket R (with Bush LFF-1510) | E30 08619A | 2 | ||
| 4 | stopper Rubber A | F90.01790A, | 4 | ||
| 5 | Side Bracket L (with Bush LFF-1510) | E30 08618A | 2 | ||
| 6 | Oiles Flange Bush 80F-0905 | F90.0198A | 8 | ||
| 7 | Shaft Bracket | E90 00669B | 2 | ||
| 8 | Up Bose | £90 0031298 | 2 | ||
| 9 | Olles Flange Bush 80F-1810 | F5001799A | 4 | ||
| 10 | Stopper Rubber B 10.1X18X12 | F9DOI791A | 2 | ||
| n | Washer | £30 06163A | 2 | ||
| 12 | Under Base | £30 08620 | 2 | ||
| 13 | GearA | £70 00132B | 4 | ||
| 4 | Gear Bracket | £30 061648 | e_| | ||
| 15 | Gear 8 | £70. 00133A | 4 | ||
| 16 | Volume Bracket | E30 06165B | 4 | ||
| 7 | Variable Resistor 5K-B EWSWI1F20E53 | A21 025414, | i | 4 | “| |
| 18 | Spacer - 5L | £10 00881B | | | 4 | |
| 19 | Tension Spring | £40 00275A | 4 |
€ # Alawassy NNS
a
Gun Assembly Parts shown on page 16
Description Part No. Qty.
| 1 | Solenoid Bracket | E30 06168A | 2 | |
| 2 | Rubber Leg K-24 | F30 00024A | 2 | |
| 3 | Frame | E30 08614A | 2 | |
| 4 | Plunger | 310 01124A | 2 | |
| 5 | Cushion Rubber 13X18X6 | F90 02519A | 2 | |
| 6 | Solenoid Spring | E40 00362A | 4 | |
| Ui | Solenoid | C1101225A | 2 | |
| 8 | Diode 1N4003 | A02 00113A | 2 | |
| 9 | L-Bracket | E30 06169A, | 2 | |
| 10 | Trigger Bracket | E30 08615B | 2 | |
| 14) | Trigger | F90 03628A | 2. | |
| 12 | Trigger Spacer | E10 01125A | 2 | |
| 13 | Trigger Spring | E40 00363A, | 2 | |
| 14 | Slide Base | E30 08616D | 2 | |
| 18 | Slide Bush | F90 02484A | 4 | |
| 16 | Slide Shaft | E1001126A | 4 | |
| 7 | Slide Stopper Rubber 5X16X18 | F90 02520A | 2 | |
| 18 | Return Spring | E40 00365A | 2 | |
| 19 | Spring Spacer | F90 02530A | 2 | |
| 20 | Bumper 5X16X5 | F90 02543A | 2 | |
| 21 | Stopper Bracket | £30 08617 | 2 | |
| 22 | Micro Switch $S-5GL2 | C02 001834 | 4 | |
| 23 | Magnet Bracket | - | E30 08626A | Z| |
| 24 | Magnet | 7 | H90 00218A. | 2 |
| 25 | Magnet Cover | 7 | E30 08627A | 2 |
(Not Shown) | K Harness 190 03189A 2
$<...
Test OF CONNECTOR TERMINALS
Main PC Board
Sub PC Board
G CONNECTOR |
| Part mounted side | Soldered side | Part mounted side | Soldered side | ||||
| GND | [1 | a |enp | TEST | is|s | | a | |||
| GND | | 2/8 |enp | COIN 1 | 16 | T | |COIN2 | |||
| +5V | | 3/ | c |+sv | 7 | u | ||||
| +5V | | 4] | D |+5v | 18 | v | ||||
| 5V | | s| | © [sv | 19 | w | ||||
| +12V | | 6| F |+1av | 20 | x | |||||
| POST | 7| | 4 |Post | 21) | ||||
| METER 1 | | 8 | J | |METER2 | TRG IP | | 22 | z [TRG 2P | |||
| LOCK OUT 1 | 9| | Kk |Lock our2 | BOMB IP | 23 | a | BOMB 2P | ||
| SP (+) | 10} | L [spc | BSET IP | 24 | |b | BSET2P | | |
| ni | Mm | 2 | £ | ||||
| VIDEO R | 12| | N | VIDEOS | 2) | d | |||
| VIDEO BL | P| VIDEO SYNC | ites | |||||
| VIDEO GND | R | SERVICE | f |
© CONNECTOR P CONNECTOR 1 |45V 2 |vRIPX 2 |+24v 3 |vRIPY 3 |+12v 4 | VR 2px 4 |+12V 5 | VR2PY 5 |+5V 6| 6 | +5V, 7 | Z 7 |GND 8 | 8 |GND- 9 9 | +24VGND 10 |GND 10 | +24VGND
Power WirING DIAGRAM
- Fuse is 2AS.8.
- Varistor is 250V Ee
POWER WIRING DIAGRAM [a3
See Voltage | Selection!
WHT-RED BRN 100
BLU-BRN BLU-WHT
BRN-WHT_
From Line Filter one ona
ar Ow
N 120V Isolated For Monitor And Power Supply
5.9V For Coin Door Lights. Note: Fuse is 1A S.B., 250VAC
Gun Coil
Sound Board
Shown As Jumpered For 120V Operation.
ee
Power Supply SWITCHER ASSEMBLY
Len F ot > aN SS. Zs Sec
| Part Number | Description | € | ~——} | ||||||
| Ol | ssv 42a | H-17914 | Switcher Power Cable | —f=—) | < | —) | ||||
| 01-10500 | Mounting Bracket | s | aie | = | S | ee | = | ||
| ° | GND | 01-12162 | Shield | ¢ | > ¢ | > | < | c | > |
| i | 20-9920 | PIS | Swit | —s=—) | = | > | |||
| ail | ans | ‘S Switcher Supply | ——} | s | > | <=> | |||
| sal | Ss | — | |||||||
| ° | SV 1A | S55 | —— | ||||||
| ° | +12V 2A | : | ‘ | ‘ | i | 2 |
+ FG 2 ef. of ©
| loll} | *° | ata Sa |
| ° | AC | il |
neo (su
= N) oneonveuow VOLETIWIOLET-YELIOW BACK prac, ORANGE (+ 12V)
vyaLow (sv)
JAMA Chart Function Wire Color i jin | Wire Color | Function
Black Ground
Red +5Vdc Red +5Vde Yellow -5Vdc Orange +12Vde Key _ Brown-Red Meter 2 N/C Brown-Gray Speaker (-)__ [wc
Green Video Green White-Gray Service Switch
White __[ Video Sync
Black-Green_| Tilt Switch Black-Red Coin 2
Violet-White Start2
NW/C NIC N/C N/C Violet-Yellow_| 2 Push 1 Violet-Green_|_2 Push 2 N/C N/C NC
Ground —!
Ground Black
+5Vdc Red +5Vdc Red -5Vde Yellow, Orange Key Brown N/C Speaker (+) __| Red-Gray _ NC Video Red Red Video Blue Brown Video Ground _| Shield Test Switch Black-Blue Coin 1 Black-Brown. White NC Twe N/C NC White-Yellow White-Green N/C N/C NIC
i ]0 Ja.lo |o}m|N}<|>x<}S]<|C|A] O) wD} -v)Z]Z IH AIC |X| YM] OO] O} W) > co} C0] 1] >} cn] 4] G9} ro}
ThiTO
TAITO AMERICA CORPORATION 390 Holbrook Drive Wheeling, IL 60090 Telephone: (708) 520-9280 Fax: (708) 520-1309
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
WHI/YEL YEL SEE POWER
WIRING DIAGRAM
PAGE 19
___0R6 ak
au SEE POWER
WIRING DIAGRAM
PAGE 19
45 RED D bax] POWER SUPPLY SWITCHING
SEE POWER WIRING. DIAGRAM FOR AC POWER CONNECTIONS