Sarge UR Parts and Operating Manual (0B88-00300-0000)
Sarge U.R. (Bally Midway MFG. CO) · Parts & Operating Manual · 67 pages · 25 sections · original scan
¢ SARGE U.R.
Parts, and Operating Manual
Cielly
MIDWAY MFG. CO
10601 W Belmont Avenue Franklin Park. Winow 60134 USA
Phone (312)451-9200 Cable Address MIOCO Telex No. 72-1596
OB88-00300-000"
ELECTRICAL BULLETIN FOR ALL APPARATUS COVERED BY THE CANADIAN STANDARDS ASSOCIATION (CSA) STANDARD C22.2 NO. 1. WHICH EMPLOYS A SUPPLY CORD TERMINATED WITH A POLARIZED 2-PRONG ATTACHMENT PLUG
ATTENTION: POUR PREVENIR CHOCS ELECTRIQUES NE PAS UTILISER CETTE FICHE POLARISEE AVEC UN PROLONGATEUR. UNE PRISE DE COURANT OU UNE AUTRE SORTIE DE COURANT. SAUF S! LES LAMES PEUVENT ETRE INSEREES A FOND SANS EN LAISSER AUCUNE PARTIE A OECOUVERT
Cally| MIDWAY Guiles You Ta Use
OUR TOLL FREE NUMBER FOR
SERVICE INFORMATION CONCERNING THIS GAME, OR ANY OTHER BALLY/MIDWAY™ GAME YOU NOW HAVE ON LOCATION.
CALL US FOR PROMPT, COURTEOUS
ANSWERS TO YOUR PROBLEMS.
Video or Pinball - Continental U.S. 800-323-7182
CBvallly MIDWAY 02:0 seron svene Harun am nos 609 pre 2148.30
- COPYRIGHT MCMLXXXV BY BALLY MIDWAY MFG CO. ALL RIGHTS RESERVED
NO PART OF THIS PUBLICATION MAY BE REPRODUCED BY ANY MECHANICAL, PHOTOGRAPHIC. OR ELECTRONIC PROCESS, OR IN THE FORMOF A PHONOGRAPHIC RECORDING, NOR MAY IT BE TRANSMITTED, OR OTHERWISE COPIED FOR PUBLIC OR PRIVATE USE, WITHOUT PERMISSION FROM THE PUBLISHER. THIS MANUAL IS FOR SERVICE USE‘ONLY, AND NOT FOR GENERAL DISTRIBUTION. FOR PERMISSION REQUESTS. WRITE: BALLY MIDWAY MFG. CO. 10601 W. BELMONT AVE., FRANKLIN PARK, iL 60131.
Printed in U.S.A.
SARGE U.R. - 2 PLAYER TABLE OF CONTENTS
SECTION 1 INSTALLATION AND GENERAL GAME OPERATION INSTRUCTIONS
DESCRIPTION PAGE
INSTALLATION. sccccccveccccvvvevccscceee cece cece nce e ec teeeecceeereeeeseel
TO SERVICE THE CONTROL PANE Ls secccccccccccccccssnensesccccccerenssssscccccce!
REMOVAL OF THE MAIN-DISPLAY=GLASS AND/OR THE TeV. BEZEL eccccceccccccccscceeed
VOLUME CONTROL POT/OPTION SWITCH LOCATIONS cececcceccscccccsccescceccssecereed
SELF-TEST MODE cccccrccccvccccccccevcscncscsecsssee reese ssensescsseesseneeeer
OPTION SWITCH SETTINGS ccccccccccceccccscccsccscecscsvacccrecsssceesssseseseel
P.C. BOARD REFERENCE DRAWING. ccsccccccccncccnssccnccccccccssssssesssessseseed
TROURLESHOOTING PROCEDURES cecsccceccccccccccccccccccssscescscccsessseceseesel
-I-
SARGE U.R. — 2 PLAYER SCHEMATICS AND WIRING DIAGRAM TABLE OF CONTENTS
SECTION 3 COMPONENT LAYOUTS, SCHEMATICS & WIRING DIAGRAMS
DESCRIPTION PAGE
WELLS GARDNER MONITOR SCHEMATIC - 19" ca cccccncccceccccscccssscceesseseeal
WELLS GARDNER MONTIOR PARTS LIST.ceee
ELECTROHOME MONITOR SCHEMATIC = 19%. eccccccencccccccceeevsccnsccersseeed
ELECTROHOME MONITOR PARTS LiSTsscsssccccccvcscccncsscverssssccessessseeed
WIRING DIAGRAM = IIPR{GHT.(MONOROARD P.C.B. W/SWITCHING PsS. .ecceeeee ened
TURRO CHEAP SQUEAK P.CeRe - COMPONENT LAYOUT se ccccccccccccescecnsenees eed
TURBO CHEAP SQUEAK P.C.Re - SCHEMATIC. ccccccccenccesccccccsceceveccsencel
DUAL POWER AMP P.C.A. — COMPONENT LAYOUT. cccccsevccccccccncecncceeseseeed
DUAL POWER AMP P.C.R. = SCHEMATIC. cceccsecccnccenccscserccsceneravereseed
OPTICAL ENCODER P.C.R. = COMPONENT LAYOUT. ceseceveeece
OPTICAL ENCODER P.C.R. ~ SCHEMATIC. ccsecercccseccrecereceseserccerecerell
SWITCHING POWER SUPPLY P.C.B. - 130VA - SCHEMATIC. scecccccscccenacccces le
UNI=POWER SUPPLY CHASSIS ASSY. = 130VA ~ SCHEMATIC... ere re)
MONOROARD) -— COMPONENT LAYOUT cocsccccccccccccccecsssscccsscscsssccessve lf
MONOBOARD = SCHEMATIC ceccecccccccccccccsencceccscsecccscccccssveseresel
EPROM LIST (MONOROARD SYSTEM) .. 0000025
~TI-
SARGE U.R. - 2 PLAYER TABLE OF CONTENTS
SECTION 2 ILLUSTRATION PARTS BREAKDOWN
DESCRIPTION PAGE
FRONT ocecesccccccnncesec sree ee nese en seers esse esas esse eseeseeeeenses ene
FRONT = PARTS LISTeccccccccccscevccccencscessceccsestscvestetsrsssseesass
REAR ACCESS (INCLUDES MONOROARD PeCeRadeccscccccceccceccncvcceccesseeered
REAR ACCESS - PARTS LIST ecwccecscccccsccccccrenscsssecccesesecesseseseesl
POWER CHASSIS: 130VA (SWITCHING) ccccceccseccccereccseccsecvecesenseesseed
POWER CHASSIS: 130VA (SWITCHING) - PARTS LISTecccccccccccvcccccccccceeeed
FRONT DOOR ASSEMBLY = UsSsAe 25¢seeccecvcrccncreccecrevscccvereressesee lO
FRONT DOOR ASSEMRLY = UsSeA. 25¢ = PARTS LiSTecscseccccescccrecesecseeel
CONTROL ASSEMBLY cecccccececcecrecccscccrcecensrecesscesseseseseensssseels
CONTROL ASSEMRLY - PARTS LIST eccsecccccccccrccscsccccesscccceecvesesensl®
-Il-
GENERAL_ INSTRUCTIONS
for:
SARGE UR.
INSTALLATION
2.
3. Remove keys from the taped coln return siot and unlock to open the coln box door,
Remove four (4) "CABINET LEVELING LEGS" from Inside the coin box.
Ttp the cabinet to the side and remove the shipping cleats from its bottom,
° Locate the threaded holes - one In each corner ~ and Instal! the "CABINET LEVELING LEGS" In them.
° Level the cabinet.
° When finished, the cabinet should be stable In the upright position,
be Unlock and remove the rear access door to gain access to the 3-pronged | Ine cord. Reinsta!! the rear access door.
Connect the 3=pronged !ine cord to a 3-slot A.C. wall outlet to Insure proper grounding.
The power ON/OFF switch is located:
UPRIGHT MODEL: On top at the center of the cabinet.
TO SERVICE THE CONTROL PANEL
1. UPRIGHT MODEL:
The contro! pane! Is held in place by three (3) spring clamps which provide constant pressure, on the strikes.
= AFTER turning power to the game off, they can be reached through the coin door,
To release the clamps, !Ift up and toward the center of the control! panel.
. Once they are released, unhook them from thelr strikes. The third clamp Is located near the center of the control panel.
To remove the contro! panel: Ralse It up and tilt It toward you until you can see the cable behind it.
. CradlIng the contro! panel between yourself and the cabinet, disconnect it from It's cabling and any miscellaneous hardware.
The contro! pane! is now loose and may be serviced.
To reinstall! the contro! panel, reverse this procedure.
REMOVAL OF THE MAIN~DISPLAY~GLASS AND/OR THE T.V. BEZEL
- UPRIGHT MONEL:
NOTE: in order to do this, the contro! pane! MUST be removed first. See the
"UPRIGHT MODEL" procedure,
. Turn the power to the game off and remove the contro! panel. This frees the matn=-display-glass so it can be removed,
. Ry putting your finger In the hole In the middle of the maln-display-giass support, you can lift it up and out.
° Remove the bezel! securing screws and the bezel may be removed,
- To reinstall the T.V. bezel and ‘the maln-disptay-glass, reverse this procedure,
VOLUME CONTROL POT / OPTION SWITCH LOCATIONS
The volume control pot Is located, along with the credit switch and the self-test switch, just Inside the cabinet on the right side of the coin door frame. The option switch Is located as shown In the attached P.C. Board reference drawing. For adjustment, It can be reached through the games rear access door.
To make the sounds fouder, turn the volume pot clockwise as you face It.
To make the sounds less loud, turn the volume pot counterclockwise as you face It,
SELF-TEST MODE
The Self-Test mode Is a special mode for checking the game switches and computer functions. tt Is the most complete way of checkIng for proper game operation and Is quite easy to use.
The Self-Test mode may be entered at any time and from any mode of operation. Simply locate the black slide switch Inside the Coln Box compartment and slide it to the Self-Test position. With this switch In the Self-Test postion, activate the stam switch located on the Coln Door, The game wil! enter the Self-Test mode Immediately and display the fol low!ng test menusese
1, SELF DtAGNOSTICS
- SOUNDS
- PLAYER INPUT
- GRID DISPLAY
MOVE CURSOR DOWN BY MOVING GRIP CONTROL HANDLE DOWN. MOVE CURSOR UP BY MOVING GRIP CONTROL HANDLE UP HIT START BUTTON FOR TEST
1, SELF DIAGNOSTICS: This test Is designed to effectively locate and Identify any malfunction of the on~board computer. When selected, the game enters thls mode Immedlately and begins scanning the memory stored In rom and ram, If a defective component !s found during the scan, that component and It's location will be displayed on screen. It wit! take about 15 seconds to perform the entire test.
- SQUNDS: When selected, this test wll! disptay a menu of sounds, The first two selections on the menu are ALL and EXIT. tf you move the cursor to select ALL the game w!|! automaticaily perform a test of all the sounds on the menu, If you move the cursor to select EXIT, the game wlil! exit the sound test and return to the main menu page. While In the sound test, any selection on the sound menu may be tested Individually by positioning the cursor next to that sound and pressing the SELECT button.
- PLAYER INPUT: This test Is designed to confirm the operation of all player Inputs and devices Im the game, For example, when you wish to test the co!ln switches on the coln door, you would enter this test and activate the coln switches. !f the switches are operating property, the screen wll! display the words COIN CHUTE 1 or COIN CHUTE 2 depending on which coln switch has been activated. Al! Inputs, pin controts, service switches, etc. may be tested In the same manner. To exit this test, activate the cotn door stam switch.
4, GRID DISPLAY: This test was designed to display a crosshatch pattern used In ad= justing the color monitor. This pattern may be used to adjust convergence, color balance, vertical IInear!ty, and vertica!/horizonta!l size. To exit this test, activate the coln door slam switch.
{MPORTANT NOTE: There 1s NO battery back up provided for this game. All logic & memory functions wil! be retained thru dip switch settings.
SARGE U.R.
OPTIULON sSWwiTcCH SETTINGS a ———— VILIDITITITISTILI TIL LT SWATCH NOw 2 — AT A 13 = LOCATED ON MONOBOARD/SS//SS//SSISISILSSTT LL ——-____—_---_-—_—__+| SW#1 SWE2 SWE3 SW#4 SWS SW#6 SWE7 SWEB SW#O SW#IO NOT NOT NOT NOT NOT NOT USED USED USED USED USED USED
NO FREE PLAY DURING GAME PLAY:
OFF FREE PLAY ON
#® 1 COIN / 1 CREDIT OFF OFF 2 COINS/ 1 CREDIT ON OFF 1 COIN / 2 CREDITS OFF ON
#% NORMAL OPERATION FREEZE VIDEO
PART NO. M051~00B88-A007 od
THE REMAINDER OF YOUR NEW GAME'S MOST COMMON OPTION SETTINGS ARE CONDUCTED DURING YOUR GAME'S SELF-TEST MODE
PC. BOARD REFERENCE DRAWING
_FOR MONOBOARD SYSTEM
MONOBOARD A084-91787~ABB8
OPTION SWITCH "2"
(10=POSITION)
12 3 4 5 67 8 9 10
ON POO GH EAGER) | OFF
INTRODUCTION
This manual offers generalized troubleshooting procedures for common types of malfunctions which can be appiled to most video games. We wil! not attempt to give you specific Instructions for troubleshooting particular games because thls would Involve hundreds of pages of more repetitive Instructions, differing only In the specific detalls of each game,
The most common problems occur in harness components such as the coln acceptor, player controls, Interconnecting wiring, etc. These areas are covered In moderate detall.
The TV Monitor and Game Logie Printed Circult Boards (PCB's) provide their fair share of problems too, but not to the extent of the harness and. I+s component parts.
As you already know, the Game Logie PC Boards are complex devices. Each contalns a great number of different Interrelated circults. The major changes which give each game Its own particular Individuality are accomp!Ished In the EPROMS and other Intigrated CIrcult devices that are Installed on each of these PC Boards.
GENERAL TROURLE SHOOTING SUGGESTIONS
The first step In troubleshooting Is to correctly Identify the malfunctions symptoms, This Includes not only the clrcults or features malfunctioning, but also those stI!! operational. A carefully tralned eye wil! pick up other clues to what's wrong as well. For [n= stance, a game in which the computer functtons fal! completely just after money was collect= ed may have a quarter shorting the PCR traces. Often an experienced troubleshooter will be able to spot the cause of a problem even before opening the cabinet,
After all the clues are carefully considered, the possible malfunctioning areas can be narrowed down to one or two good suspects. Those areas can be examined by a process of el|mination untl! the cause of the malfunction Is d!scovered.
HARNESS COMPONENT TROUBLESHOOTING
Typical problems falling In thls category are coin and credit problems, power problems, and failure of Individual! features,
NO GAME CREDIT - ~ For example, a prospective game player Inserts a quarter or token and Ts not awarded a game, The first thing to check [s whether or not the quarter or token [s returned. {f I+ was returned, the malfunction most certainly !tles In the coln acceptor Itself, First, use a set of test colns (both old and new) to ascertain that the player's coln Is not undersize or underwelght. If your test coins are also returned, coin acceptor serv- Ictng Is Indicated. Generally, the cause of this particular problem |s a matadjusted magnet gate. Normally, this will mean slightly closing the magnet gate by turning the adjusting screw out a bit.
{¢ the quarter or token Is not returned and there Is no game credit, the cause of the mal~ function may be In one of several areas. First, try operating the coln return button; If the coln Is returned, the problem Is most !Ikely In the magnet gate. Enlarge the gap ac~ cording the coln acceptor manufacturers service procedures. (tf this does not cure the problem, remove the coln acceptor, clean It, and perform the manufacturers suggested major ad— justment procedure.
!f the trapped coln Is not returned when the wiper lever is actuated, you may have an acceptor jammed by a slug, gummed up with beer, a jammed coin chute, or mechanical fallure of the acceptor mechanism. In this case, first check for the stug that wll! genera!!y be trapped against the magnet. tf a slug Is found, simply remove It and test the acceptor. {f the chute Is blocked, remove the acceptor and remove the jammed coins. If there Is actual failure of the acceptor, remove the unlt and repair as Indicated by the acceptor manufacturers service procedures.
!f the cotn Is making Its way through the acceptor (that Is, falling into the coln box), yet there Is stil! no game credit, you elther have a mechanical! fallure of the coln switch or electrical fallure of the coln and credit circults. The first place to begin Is by checking the coln switch. Most of these switches are the make/break variety of micro switch, They are checked for continulty between the "NO", "NC", and "Ct terminals, When not actuated, the "NC" and "C" terminals shou!d be continuous and the "NO" terminal open. When actuated, the "NO" and "C" terminals should be continuous and the "NC" terminal open. If the coin switch checks good, Inspect the solder connections to the coin switch terminals to be sure there Is good contact at this point. If necessary, use a continulty tester and check from the terminal Jug on the switch to the assoclated PCB trace. This wil! tel! you if there Is a continuous |!ine al! the way to the cred!t clrcult.
lf the colIn switch wires do check good, the problem Is In one of the game !ogic boards - = most likefiy In the coln and credit cIrcultry.
tf you do get a game credit when a coin Is deposited, but the game wil! not start when the one or two player start button Is pressed, there may be a problem In the start switch, the Interconnect!ng wiring, or the game logic boards. First, check the switch, If the switch Is OK, proceed to check the wiring. Again, make sure you go from the termina! tug on the switch to the PCR trace. This way, you wllf check the terminal contact as wel! as the PCR edge connector contact. If the wiring Is continuous, proceed to check the PCB credit cir= cuit. If not, check each section .of the wiring, untii the discontinuity Is located. If the wiring ts OK, the problem must !le In the games logic boards.
TRANSFORMER AND LINE VOLTAGE PROBLEMS
Your game MUST have the correct IIne voltage to operate properly. If the |Ine voltage drops too low, one of the games logic clIrcults will disable the credit acceptance circult. The point at which the games logic cIrcults wi!! fall to function Is approximately 105 volts AC.
Low line voltage may have many causes. LIne voltage normally fluctuates a certain amount during the day as the total usage varles, Peak usage times occur malnty at dawn and/or dusk. So If your games problem seems to be related to the time of day, this may be a factor, A large load connected to the same !Ine as the game (such as a farge alr cond!tioner or other device with an exceptionally large electric motor) may drop the IIne voltage s!gnificantly when starting up. ThIs drop can result In an Intermittent credit problem, In addition, poor connections In the locatlon wiring, plug, or !!ne cord may also cause a signiflcant drop In power. Cold solder joints In the games harness, especially In areas !ike the transformer connections, Interlock switch, or fuse block, may a!so produce the same re~ sults, although probably on a more permanent basis.
Sometimes location owners (especially In bars) replace IIght switches with dimmer rheostats, and the game Is sometimes on the same IIne, Obviously, the voltage avallable to the game js going to drop dramatically when the dimmer 1s turned down.
In any case, the way to check for proper |Ine voltage ts with your VOM, Set the VOM to the 250 VAC scale and stick the probes Into the wal! outlet the game was connected to. If It's OK here, check the transformer primary connections. {tf you do not get 117 VAC, examine the solder joInts on the transformer, fuse block, and Interlock switch. If you do get 117 VAC, the problem must be elther In the transformer, harness connections, or In the PCB power supply.
\# you suspect the transformer, check Its secondaries with the VOM set to the 50 VAC scale and correlate the readings with the legend on the side of the transformer, The transformer must also be correctly grounded, so check the ground potentia!t as well, especlatly If there 1s a hum bar rolling up or down the Monitor screen.
NO POWER, NO PICTURE - - If the Monitor screen Is completely dark, first look in back of the Monitor to see If the CRT filament Is glowing. [{f It Is, try adjusting the brightness control. {tf no luck here, put your ear near the Monitor and IIsten for the high-pitched B+ hum produced by the flyback transformer. If you get the hum but no picture, and you have tried adjusting the brightness, major Monitor servicing Is Indicated.
{# the monttor seems completely dead, check the rest of the game to see !f It has power, If It doesn't, go directly to the wall outlet and check there. If OK there, check the game fuse(s), Interlock switch, and Interconnecting wire lengths.
Sometimes It Is difficult to tell If a slow=blow fuse has blown. {tf In doubt, check It us- Ing any of the VOM "R" scales.
HARNESS PROBLEMS - ~ Other harness problems Include blowIng fuses and matfunction!Ing controls, The repeating blown-fuse problem can sometimes be quite exasperating to solve. Short cIrcults have the tendency to occur In areas almost Impossible to find. First, try Insert- Ing a new fuse as old fuses age and sometimes hlow without cause. If the new fuse also blows, you definitely have a short.
The best way to approach thls problem Is by d!sconnecting devices that may be caus!Ing the problem, such as the TV Monitor, the varlous PCB's one at a time, and the Isolation trans~ former. Disconnect the devices by FIRST turning the game off, disconnecting It from its wall outlet. Remove the blown fuse and connect your VOM across the terminals of the fuse block (this wil! save blowIng a fuse each time you want to check the cIircult). Set your VOM to one of Its resistance scales. You should be reading a short. If not you probubly have a part that only shorts out after It Is heated up ~ we'l! cover this Im a minute. So, assuming you are reading a short on your VOM, disconnect the components from thelr cabling one at a time, checking the VOM after each one Is disconnected. When the short disappears, you have just disconnected the bad component. {f al! components are disconnected and the short still remains, the problem Is In the harness and only patient exploration wil! reveal its focation. Carefully examine all the wiring, looking for terminals that may be touching, metal objects such as colns shorting the connections, or burned Insulation, if necessary, use the VOM to check each suspected wire.
OK, now lets assume that you connected your VOM across the fuse block terminals as stated above and you did not read a short. This most !lkely means that you have a component somewhere In that game that ONLY goes bad AFTER it heats up. {+t checks good when Its cold. In thts case, turn the game off and disconnect ALL of Its components. Insta{il a known good fuse In the fuse block. And turn the game on. If the fuse does not blow after a tew minutes, you know that It Is not anything to do with the wire harness. (In this Instance, It shouldn't be, actually, Aut It never hurts to check.) Next, turn the game off again and reconnect ONE component, Turn the game back on and wait a few minutes to see If the fuse blows, If It does not, turn the game off again and reconnect another single component,
Turn the game back on and walt a few minutes to see If the fuse blows. Repeat thls procedure unti! the fuse blows. When I+ does blow, the last component you connected has the part on it that Is golng bad after It warms up and Is shorting out.
MALFUNCTIONING CONTROLS - - The most common problem here {s the bad potenttometer (pot). Typically, a bad pot wlli cause the Image on the screen to jump when I+ reaches a certain polnt. The onty cure for thls one Is to Insta!! a new pot.
\# a feature that Is operated by a switch (for example, joysticks, foot pedals, control panet buttons) does not operate at all, check the switch wlth a VOM or continuity tester to verlfy Its operation. if the switch does not check good, replace It, If the switch Is OK, you should suspect the Input to the switch from the PCB. In this case, get out the harness and logic schematics and check to see what kInd of Input Is supposed to be at this switch, In many cases, the Input wlll be +5 volts DC. If so, use the VOM to check Its presence with the game turned on. Normally, the switch Is used to pu}! a +5 volt DC !Ine LOW to GROUND or to pul! a LOW Ine HIGH. If the PCR output Is missing, check the wire length from the PCR, if you find the stgnal at the PCR trace, the wire length or connection [fs at fault. (ft there [s no s!gnal at the PCB trace, begIn exploring the PCR usIng the logic schematics and game manual.
~9-

This page is a drawing, shown as the original scan.
SECTION 3 Component Layouts,
Schematics & Wiring Diagrams
COIN pone LIGHTS.
6 Ps vioro came HONo Bone” 91787-aRan reve CHING POWER SUPPLY
at 2apas 2e1e aus ena
= most @aRea-aner ieee
Fan Co
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
J rosie cxouno J conrn croono T ewmcos oxouno
ANALOG GROUND
NOTES -——_—— baie BALLY MIDWAY AFG. CO.
TER 378-85 senenaric
THIS DWG IS CONFIDENTIAL & PROPERTY OF BALLY/MIDWAY MFG CO Dim. TOLERANCES ee aur vane
Ci
SCALE CONCENTAICITY TIR 002 j AE | © ia FRANKLIN PAK, iL 60131
FRACTIONAL REVISIONS
DECIMAL _ TURBO CHEAP SQEAK ANGLE eG . 5. 1-4 -f-1-2-6 DO NOT SCALE DWG. — A084-91779-B000 pore
M051-00114-8126 TURBO CHEAP SQUEAK A084-91779-B000
DESIGNATION LIST
DESIGNATION CP1=CP11 cl C2-C3 C4=C9,C37 c10 cu C12 C13 C14 C15 C16 cy C18 c19 c20 €21-C22
c24 c25 C26
€28-C29 C30 €31-C34 C35-C36
RI R2 R3 R4-RB RO R10 RI-R12 RIS“R16,R62 RIT R18 RI9 R20 R21 R22 R23 R24 R25 R26 R27 R28 R29 R30 R31 DESCRIPTION 2O1MF AX. CR. 18PF AX. CR. 820PF AX. CR. 1OOPF AX. CR. 1OMF RD TANT ~OIMF AX. CR. ATMF AX. ELECT. 2OIMF AX. CRe 270PF AX. CR. IMF RD TANT OO56MF AX. CR. 270PF AX. CR. IMF RD TANT 470PF AX. CR. 150PF AX. CR. IMF RD TANT 680PF AX. CR. »O1MF AX, CR. 47MF AX. ELECT. IMF RD TANT 68PF AX. CR. «OIMF AX. CR. 1OMF RD TANT 390PF AX. CR. 470MF AX, ELECT.
4.7K OHM 1/4W 5% 3.3K OHM 1/4W 5% 150 OHM 1/4W 5% 4.7K OHM 1/4W 5% 100 OHM 1/4W 5% 47K OHM 1/4W 5% 100 OHM 1/4W 5% 1OK OHM 1/4W 5% 100K OHM 1/4W 5% 10K OHM 1/4W 5% 100K OHM 1/4W 5% 10K OHM 1/4W 5% 4.7K OHM 1/4W 5% 47K OHM 1/4W 5% 360 OHM 1/4W 5% 2.7K OHM 1/4W 5% 180 OHM 1/4W 5% 360 OHM 1/4W 5% 120K OHM 1/4W 5% 330K OHM 1/4W 5% 4.7K OHM 1/4W 5% 510K OHM 1/4W 5% 120K OHM 1/4W 5% DESIGNATION
R32 R33 R34 R35 R36 R37 R38 R39 R40 R41 R42 R43 R44 R45 R46 R47 R48 R49 R60 R61
o1 02-04
{cs U3 ICS U4-U6 Ics 10 (cs ull
FBI-FR4 JW1=JW5 Swi PAGE 2 of 5
DESCRIPTION
33K OHM 1/4W 5% 18K OHM 1/4W 5% 110K OHM 1/4W 5% 33K OHM 1/4W 5% 150K OHM 1/4W 5% 82K OHM 1/4W 5% 510K OHM 1/4W 5% 150K OHM 1/4W 5% 24K OHM 1/4W 5% 3.3K OHM 1/4W 5% 24K OHM 1/4W 5% 330K OHM 1/4W 5% 160K OHM 1/4W 5% 100 OHM 1/4W 5% 560K OHM 1/4W 5% 24K OHM 1/4W 5% 4.7K OHM 1/4W 5% 2.7K OHM 1/4W 5% 1K OHM 1/4W 5% 1K OHM 1/4W 5%
MPS 3646 2N5305
C1K OSC T4LS76 68B09E EPROM/ROM EPROM/ROM 2K X 8 RAM 74LS139 74LS02 74LS00 68B21 AD7533 40106 LM359 LM359 3340
40 PIN tC SOCKET 28 PIN IC SOCKET 40 PIN IC SOCKET 16 PIN 1C SOCKET
FERRITE BEAD JUMPER WIRE PCB SWITCH
M051-00114-B 126 TURBO CHEAP SOQUEAK A084-91779-B000
DESIGNATION LIST
DESIGNATION DESCRIPTION
LED 1 GREEN LED ul CLOCK OSCILLATOR 8MHZ Jt 9 PIN KK100 R/A J2 12 PIN KK156 R/A J3 12 PIN KK100 R/A MTHW 1-4 SPACERS PCB TURBO CHEAP SQUEAK PAGE 3 of 5
PAGE 4 of 5 M051-00114-B 126 TURBO CHEAP SOUEAK A084-91779-B000 11/1/85 = A Sede CROSS REFERENCE.
| DESCRIPTION | oy | DESIGNATION NO. | PART _NUMBER |
| 18PF AX. CR. | 1 | ct | 0¢48-00800-0001 |
| 68PF AX. CR. | 1 | C27 | 0307-00800-0011 |
| 1OOPF AX. CR. | 7 | C4,05,C6,C7,C8,C9,C37 0304-00800-0001 | |
| 150PF AX. OR. | 1 | 20 | 0307-00800-0010 |
| 270PF AX, CRs | 2 | C14,C17 | 0307-00800-0009 |
| 390PF AX. CR. | 4 | €31,C32,C33,C34 | 0986=00800-3000 |
| 470PF AX. CR. | 1 | c19 | 0307-00800-0008 |
| 680PF AX. OR. | 1 | C23 | 0358-00800-0002 |
| B20PF AX. OR. | 2 | 2,3 | 0304=00800-0002 |
| .0056MF AX. CR. | 1 | C16 | 0307-00800-0007 |
| sO1MF AX. CR. | 15 | CP1-CP11,C13,C24, | 0386-00800-2200 |
€28,C29
| IMF RAD TANT | 5 | €15,018,C21,C22,C26 — 0307-00800-0004 | |
| 1OMF RAD TANT | 2 | C10,C30, | 0307-00800-0005 |
| A7ME AX. ELECT | 2 | 12,025 | 0307=00800-0003 |
| 470MF AX. ELECT | 2 | €35,C36 | 0A 15=00800-0005 |
| 100 OHM 1/4WATT 5% | 4 | RO,RI1,R12,R45 | 100E-00005-0033 |
| 150 OHM 1/4WATT 5% | 1 | R3 | 100E-00005-0037 |
| 180 OHM 1/4WATT 5% | 1 | R25 | 100E-00005-0039 |
| 360 OHM 1/4WATT 5% | 2 | R23,R26 | 100€-00005-0048 |
| 1K OHM 1/4WATT 5% | 2 | R60,R61 | 100€-00005-0061 |
| 2.7K OHM 1/4WATT 5% 2 | R24,R49 | 100E-00005-0071 | |
| 3.3K OHM 1/4WATT 5% 2 | R2,R41 | 100E-00005-0074 | |
| 4.7K OHM 1/4WATT 5% 9 | R1,R4,R5,R6,R7,RB | 100E-00005-0079 |
R21,R29,R48
| 10K OHM 1/4WATT 5% | 7 | R13,R14,R15,R16,R18 | 100E=00005-0088 |
R20,R62
| 18K OHM 1/4WATT 5% | 1 | R33 | 100E=00005-0093 |
| 24K OHM 1/4WATT 5% | 3 | R40,R42,R47 | 100E-00005-0097 |
| 33K OHM 1/4WATT 5% | 2 | R32,R35 | 100£=00005-0100 |
| 47K OHM 1/4WATT 5% | 2 | R10,R22 | 100E-00005-0104 |
| 82K OHM 1/4WATT 5% | 1 | R37 | 100E-00005-0112 |
| 100K OHM 1/4WATT 5% 2 | RIT,RI9 | 100F-00005-0115 | |
| 110K OHM 1/4WATT 5% 1 | R34 | 100E=00005-0117 | |
| 120K OHM 1/4WATT 5% 2 | R27,R31 | 100E-00005-0118 | |
| 150K OHM 1/4WATT 5% 2 | R365 ,R39 | 100E-00005-0120 | |
| 160K OHM 1/4WATT 5% 1 | Rad | 100E-00005=0121 | |
| 330K OHM 1/4WATT 5% 2 | R2B,R43 | 100E=00005-0128 | |
| 510K OHM 1/4WATT 5% 2 | R30,R38 | 100E-00005-0133 | |
| 560K OHM 1/4WATT 5% 1 | R46 | 100E=00005-0134 | |
| MPS3646 | 1 | o1 | 104E-00001-0019 |
| 2N5305 | 3 | 02-04 | 104E-00007-0003 |
| IC 40106 | 1 | ic ul2 | 0304=00803-0056 |
| IC 74LS00 | 1 | Ic U9 | 0A15-00803-0046 |
| ie 74L$02 | 1 | Ic U8 | 0986-00803-7400 |
| 1C 74.876 | 1 | 1c U2 | 0A15-00803-0072 |
| IC 74/8139 | 1 | IC U7 | 0A15=00803-0051 |
GROSS REFERENCE
DESCRIPTION.
(C AD7533 IC LM359 IC 3340 IC 68B09E (C 68821
IC 2K X 8 RAM 1C EPROM/ROM
16 PIN IC SOCKET 28 PIN IC SOCKET 40 PIN IC SOCKET
FERRITE BEAD JUMPER WIRE PCR SWITCH LED GREEN CLOCK OSCILLATOR 8MHZ
9 PIN KK100 RT ANGLE 12 PEN KK156 RT ANGLE 12 PIN KK100 RT ANGLE SPACERS TURBO CHEAP SQUEAK eRe Soe Ne Ne Beane 3 051-001 14-8126 TURBO CHEAP SQUEAK A084-91779-B000
DESIGNATION NO.
Ic ull HC U13-U14 tC Utd (C U3 1c Ul0
1C U6 IC U4-U5
{cS UIT ICS U4-U6 (CS _U3,U10
FB1,FB2,FB3,FB4 JW1,JW2, JW3, JW, JWS swt PAGE 5 of 5
PART_NUMBER
0304-00803-0055 0304-00803-0053 0358-00803-0002 0C48-00803-0001 0A 15-00803-0074
0304-00803-0057 SEE EPROM/ROM CHART
110E-00001-0003 110E-00001-0010 110£-00001-0011
0316=00804-0002 117E-00001-0003 0986-00804-3 100 119E-00001-0001 109E-00002-0009
0017-00021-1269 0017-00021-1286 0017-00021-1288 0017-0004 2-0328 A080-91779=A000
‘DIM, TOLERANCES
UNLESS OTHERWISE SPEC
CONCENTRICITY TIR 002
= 164 + 002— 000 212"
DO NOT SCALE DWG
BmUMING: 40-107 r= SHIELD vaupio >> ¢ + pe To CHIPS
cer cp2 ces 220uF 25V dl TUF [ie
Vv AUDIO PROJECT ENG: C.MEONICK
RETURN F uis OWG 1S CONFIDENTIAL & PROPERTY OF BALLY/MIDWAY MFG CO TRON Cvilly MIDWAY wro. co.
my Dare Scat 7” " ™ | 6/4/84 ase FRANKLIN PARK, IL 60131 AEVIIONS
DUAL POWER AMP +
‘SCHEMATIC PART.NQ ec 4080-90910 FO00 MOS1-009@86-FOII
DESIGNATION LIST. DESIGNATION NO. DESCRIPTION 102 4.7 MF 25v Ro TANT 3,04 22 MF 6v RD TANT 5506 47U MF OV AX ELEC creo a1 MF SUV AX CER ct 220 NF 25v AX ELEC 62,005 AT ME SOV AK CER RI RE 2.7K UHM Vou 5%
CRON RERe 27 OHM 1/40 Sh CRON RS “RB 1 Od 1/20 5% CRON ut uz Mu37 50 at 7 PIN Je 5 PIN 5A1,2 HEATSINK ASST 1/4" SPACER CROSS REFERENCE LIST
McR/2 DUAL POWER AMP. Pc. DESCRIPTION ary DESIGNATION NO. PART NuMaER A082-90910-FO00 ~ 7 ¢7-€10, cP2, C3 u986-00811)-1190 c1,c2 u986-y08U0- 3100 3,66 0986-008)0-16:
al hog 500 ah 4.7 ME 25V RD TANT 22 ME Ov RD TANT cP1 0986-U0800-321 5,06 0986-00809 174
220 MF 25V AK ELEC 470 MF SV AX ELEC onner RS-RB 062-026.33-14Kx R3RG 0962-06803~1xxx RI, R2 162-1998 3~ 1 KXX
1 OWN 172W 5% 27 OnM 1/40 5% 2.7K ON 1/4W 5% mu37 50 2 ut v2 6-1 BBK=KXGK. TIN .045 S@ PINS 12 sNyae 0017-000 5-048 HEATSINK ASSY 2 SAT, 2 A986-99N10-CO00 1/4" SPACER 4 Mn tis p01 7-00042-0320 HC HOARD 1 4080-908 1)-F 000
we 6 CONFIDENTIAL & PROPERTY OF BALLY/MOWAY MFG_CO Cully [MIDWAY wtc.co FRANKLIN PARR 160131
PROJECT ENG C_MEDNIC| ‘IM TOLERANCES UNLESS OTHERWISE SPEC CONCENTRICITY T1002 FRACTIONAL 3 66 DECIMAL *, 005 MOLE DIA + 062” 000 REVISIONS _
eriayeal Le UAL PWR AMP ASSEMBLY DRWNG A084 90910 -FO00 PRAT NO M05 1 -00986 - F010
DIM TOLERANCES
UNLESS OTHERWISE SPEC
CONCENTAICITY T1R = 002 FRACTIONAL 2 164 DECIMAL + 005 HOLE DIA + 002— 000 ANGLE 22" DO NOT SCALE DWG. toro
ntte gord
6ole roby 2OVe edd + —see €d9 sie UMP
bd uy
u THIS DWG, optt 1 axnq3a 43009N3 WolLdoO
Old O00 - 7641 6-080V 1S CONFIDENTIAL & PROPERTY OF BALL Y/mi—OWAY MFG CO
ban ck Tat SCALE 3/8785 | Cstlly [MIDWAY wre. co. FRANKLIN PARK IL 60131 = =
REVISIONS
OPTICAL ENCODER DELUXE
PART NO 051-001-:14-AI30 SHEET / OF L
AO080-91794-A000
PAGE 2 of 2
M05 1-001 14-A130 OPTICAL ENCODER DELUXE A084-91794-AN00
DESIGNATION LIST DESIGNATION DESCRIPTION DESIGNATION DESCRIPTION
| C101 | 4.7UF RAD. TANT | R109-R110 | 200K OHM 1/4W 5% |
| cP1 | sO1UF AX. OR. | RW | 4.7K OHM 1/4W 5% |
| cP2 | YOUF AX. ELECT. | RII2 | 6.2K OHM 1/4W 5% |
| CP3-CP4 | sO1UF AX. CR. | RI3 | 3K OHM 1/4W 5% |
| cP5 | 1OUF AX. ELECT. | OPT 1 | OPTO SWITCH DUAL |
| 6 | sO1UF AX. CR. | ut | 74.8491 |
| R101-R102 | 4.7K OHM 1/4W 5% | u2 | LM339 |
| R103-R104 | 200K OHM 1/40 5% | Jy | 15 .045 SO. PIN |
R105 6.2K OHM 1/4W 5%
| R106 | 82 OHM 1/4W 5% | Jwt | JUMPER WIRE. |
| R107 | 30K OHM 1/4W 5% | Pca | OPTICAL ENCODER DELUXE |
R108 91K OHM 1/4W 5%
CROSS REFERENCE
| DESCRIPTION | OTY.. | DESIGNATION | PART _NUMRER |
| sO1UF AX, CR. | 4 | CP1,CP3-CP4 ,CP6 | 0628-00800-0100 |
| 4.7UF RAD. TANT | 1 | clot | 0628-00800-0200 |
| 1OUF AX, ELECT. | 2 | cP2,CP5 | 0628-00800-0300 |
| 82 OHM 1/4W 5% | 1 | R106 | 100£-00005-0031 |
| 3K OHM 1/4W 5% | 1 | RI13 | 100E-00005=0073 |
| 4.7K OHM 1/4W 5% | 3 | R101,R102,R111 | 100E-00005-0079 |
| 6.2K OHM 1/4W 5% | 2 | RI05,RVI2 | 100E=00005-0083 |
| 30K OFM 1/4W 5% | 1 | R107 | 100E-00005-0099 |
| 91K OHM 1/4W 5% | 1 | R108 | 100E-00005-0113 |
| 200K OHM 1/4W 5% | 4 | R103,R104,R109,RI10 100€-00005-0123 | |
| 74LS491 | 1 | ul | 0628-00803-2700 |
| LM339 | 1 | U2 | 0628-00803-2900 |
| OPTO SWITCH DUAL | 1 | OPT 1 | 120E-00001-0010 |
| JUMPER WIRE | 1 | Jw | 117E-00001-0003 |
| 15 .045 SO. PIN | 15 | Jt | 0304-00804-0010 |
| OPTICAL ENCODER DELUXE | 1 | °CB | A080-91794-A000 |
Jha @ va @®] zwAa ene ——g N2v 8 4a ©} s5v Qiza QOOHOOOOO HO] v.01 0017-00003-0543 Es ans eS
- [S whwees 0 64 I. Z. rncron vanes m mucenewenoe /Vors. FOR ADDITIONAL ELECTRICAL INFORMATION, —— — LTESeroe LES ARE Unk omen Yew, He CF REFER TO MEGH. DWG. NO. 0017-00003-0543, pera
{fer 3 srioe Tx
empamed
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
TaeuT os
reec@:7), tp co27 >, 1P2¢@#7>1 1P4COE?>
pauseaa
BALLY MIDUAY HFG. CO. HoNoROARD PC. n9e4-91707-c000 Nost-ao114-c129 suceT 18 or 25 [rcv]
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
ae
ndleo
oa Fas wy eet hee? — ste et bsp ef A ; Q ce 4 2
MONOBOARD A084-91787-C000 MO51-00114-C128
DESIGNATION LIST: Page 1 of 4 (Rev. 04 Sep 85)
DESCRIPTION DESIGNATION NO.
CP1-CP140 .01 UF AX. CER. C1,C2 390 PF AX. CER. c3 470 UF 16V¥ AX. ELEC. C4 10 UF 25V AX. TANT. C5 33 PF AX. CER. C6-C38 wi UF AX. CER. C39 10 UF 25¥ AX. TANT. c40 NOT USED (LEAVE OPEN) C41,C42 390 PF AX. CER. C43-C46 820 PF AX, CER. C47-C52 47 PF AX. CER. 53,054 470 UF 16V¥ AX. ELEC. C55 390 PF AX. CER. C56 10 UF 25Y AX. TANT. R1,R2 4.7K OHM 1/4W 5% CRBN. R3,R4 10K OHM 1/4W 5% CRBN. R5-R7 4.7K OHM 1/4W 5% CRBN. RB 82K OHM 1/4W 5% CRBN. RO 22 OHM 1/4W 5% CRBN. R10-R13 4.7K OHM 1/4W 5% CRBN. R14-R45, 220 OHM 1/4W 5% CRBN. R46,R47 2.7K OHM 1/4W 5% CRBN. R4B-R50,R52-R56 R57 R58, R59 R60 R61, R62 R63 R64, R65 R66 R67 R68 R69 R70 R71 R72 R73 R74 R75 R76 R77, R78 R79, R81-R84 R85 R86 R87 RM1-RN4 RMS RM6-RNO Dt,2 Qi Q2 Q3 4.7K OHM 1/4W 5% CRBN. 560 OHM 1/4W 5% CRBN. 10 OHM 1/4W 5% CRBN. 470 OHM 1/4W 5% CRBN. 10 OHM 1/4W 5% CRBN, 470 OHM 1/4W 5% CRBN. 10 OHM 1/4W 5% CRBN. 470 OHM 1/4W 5% CRBN. 2K OHM 1/4W 5% CRBN. 1K OHM 1/4W 5% CRBN. 510 OHM 1/4W 5% CRBN. 2K OHM 1/4W 5% CRBN. 1K OHM 1/4W 5% CRBN. 510 OHM 1/4W 5% CRBN. 1K OHM 1/4W 5% CRBN. 2K OHM 1/4W 5% CRBN, 1K OHM 1/4W 5% CRBN. 510 OHM 1/4W 5% CRBN. 560 OHM 1/4W 5% CRBN. 4.7K OHM 1/4W 5% CRBN. 1K OHM 1/4W 5% CRBN. 1K OHM 1/4W 5% CRBN. 4.7K OHM 1/4W 5% CRBN. 2.7K OHM 10 PIN SIP 4.7K OHM 10 PIN SIP 1K OHM 9 PIN SIP 1N4148 DIODE 2N4123 XSTR. 2N4403 XSTR. TIP110 XSTR.
MONOBOARD 4084-91787-C000 M051-00114-C128
DESIGNATION LIST: Page 2 of 4 (Rev. 04 Sep 85)
DESCRIPTION DESIGNATION NO.
Q4 2N4123 XSTR. Q5-Q10 MPSA70 XSTR. IC 4A 93419 64x9 RAM IC 5A T4&LS157 IC 6A,7A 7418273 IC BA-12A T4LS244 IC 140 T&LSOO TC i5A BGO 64K ROM/EPROM IC 1B T4LS245 IC 3B, 58 PROGO,PROG! 256K ROM/EPROM IC 6B 6116 2Kx8 RAM 150 NS. IC 8B T4&LS245 IC 9B 6116 2Kx8 RAM 150 NS. TC 108 74LS245 IC 11B 6116 2Kx8 RAM 120 NS. IC 12B,13B 74LS377 TC 148 BG1 64K ROM/EPROM IC 15B T4LS273 Tc 1¢ 7808 CPU IC 2¢ 2608 CTC 1c 3C 74LS157 IC 4€ T4&LS244 TC 5C,6C T4157 1c 7¢ 74LS157 Tc 8C T4F157 1c 10€ 2018 2Kx8 RAM 55NS TC 11€ T4LS244 TC 13¢ TALS86 IC 14¢ T4LS153 . IC 15C 74LS273 TC 1D 74504 IC 2D T4LS244 IC 3D-5D 74LS163 IC 6D T4ALS20 1c 7D T4&LS157 Ic 6D TALSI7T4 It 9D T4LS158 IC 10D T&LS174 1C WD T4LS157 TC 12D T4LSA74 IC 13D T4LS196 Tc 14D T4LS158 1c 15D 74LS153 IC 1€ 20 MHZ COSC. IC 2E TAFTS IC 3E 7418368 IC 4E-66,8E FG3,FG2,FG1,FGO 256K ROM/EPROM IC 9E T4FL0 Tc 10E 7415138 TC WE T4LS194 IC 12E T4LS74 IC 136, 146 T4LS194
WONOBOARD A084-91787-£000 M05 1-00114-C128
DESIGNATION LIST: Page 4 of 4 (Rev. 04 Sep 85)
DESCRIPTION DESIGNATION NO.
1 (4) T4LS161 IC ik 741804 IC 2k 7406 Ie 3K T4LST4 IC 4k T4LS32 Te 5K, 6K 7T4LS74 IC 7K T4LS169 IC 8K T4LS173 IC 9K 7T4LS169 IC 10K 2018 2Kx8 RAM 45NS IC WK TALSATS IC 12K 74LS298 TC 13K T&LSI7S TC 14K 74F08 TC 15K TALS74 ICS 4A,15A,3B,58 28 PIN IC SOCKET (.600) ICS 68,98, 11B 24 PIN IC SOCKET (.600) ICS 14B 28 PIN IC SOCKET (.600) Ics 1¢ 40 PIN IC SOCKET (.600) Ics 2c 28 PIN IC SOCKET (.600) Ics 10¢ 24 PIN IC SOCKET (.300) ICS 3E 16 PIN IC SOCKET (.300} ICS 4E-6E, 8 28 PIN If SOCKET (.600) ICs 46 24 PIN IC SOCKET (.300) ICS 86 20 PIN IC SOCKET (.300) ICS 116 24 PIN IC SOCKET (.300) ICs 5H 20 PIN IC SOCKET (.300) ICS 6H 24 PIN IC SOCKET (.300) ICS 20,39 20 PIN IC SOCKET (.300) TCS 9J, 110 24 PIN IC SOCKET (.300) ICS 130 20 PIN IC SOCKET {.300) ICS 10k 24 PIN IC SOCKET (.300) FBI-~FBI3 FERRITE BEAD Swi SWITCH PC. MTG. sw2 10 POS, DIP SWITCH OWL = OWS JUMPER at AUTO INSERT PINS TIN .045 SQ. PIN 32-36 AUTO INSERT PINS TIN .025 SQ. PIN MHQ3 SNAP PC BOARD A080-91787-C000
Released 6 Aug 85 CMM Changed 22 Aug 85 - added JCS 3£ CHM Changed 04 Sep 85 - Corrected J2-J6 to .025 Sq. Pin CMM
MONOBOARD A084-91787-C000 M051-00114-C128
DESIGNATION LIST: Page 3 of 4 (Rev, 04 Sep 85)
DESCRIPTION DESIGNATION NO.
IC 155 7418298 IC 1F 74LS367 IC 2F,3F 741820 IC 4F 74804 IC 5F T4LS32 IC 6F 74L800 IC 7F 7418378 IC 8F 748377 IC 9F 7418378 IC 10F T4F86 IC 11F 74F00 IC 12F-14F 74LS194 IC 15F TALST4 Ic 16 74LS08 IC 26 74LS138 IC 36 7418157 IC 46 MMCOIA HAL IC 56 MMCO3B HAL IC 68 74F 157 1c 76 7418283 IC 86 TALSI73 IC 96,106 7418169 IC 116 2018 2Kx8 RAM 45NS IC 126 74LS374 IC 136 74LS258 1c 146 T4LS194 Ie 1H 741832 IC 2H TAFIT4 IC 3H T4LS273 IC 4H 74LS08 IC 5H MMCO6 HAL IC 6H MMCO2B HAL 1C 7H 74F86 IC 8H 74886 1¢ 9H 74LS374 IC 10H 74°74 IC 41H 7418374 1c 12H 74LS20 1c 13H T4LS258 Ic 14H TALS174 Ic 13 74LS55 IC 2d PACNS REV 1.0 PLA Ic 3u PACOUT REV 1.0 PLA 1c 43 T4LS175 Ic 63 7418283, Ic 79 741802 IC 8) 7418374 Ic 93 2018 2Kx8 RAM 45NS IC 10J 7418374 IC 110 2018 2Kx8 RAM 45NS IC 120 7418374 IC 130 ROMCNTRL REV 1.0 PLA
MONOBOARD AQ84-91787-C000 MO51-00114-C128
CROSS REFERENCE LIST: Page 1 of 3 (Rev. 22 Aug 85)
| DESCRIPTION | qry | DESIGNATION KO. |
| 33 PF AX. CER. | 1 | cs |
47 PF OAX. CER. 6 © c47-C52
| 390 PF AX. CER. | 5 | C1, €2,041,042,055 |
| 820 PF AX. CER. | 4 | 043-046 |
| .O1 UF AX. CER. | 140 | CP1-cP140 |
| <1 UF AX. CER. | 33 | (6-038 |
| 10 UF 25V AX, TANT. | 3 | 04,039,056 |
| 470 UF 16V AX. ELEC. | 3 | 3,053,054 |
| 10 OHM 1/4W 5% CRBN. | 6 | —-R58,R59,R61,R62, R64, |
ROS
| 22 OHM 1/4 5% CRBN. | 1 | RO |
220 OHM 1/4W 5% CRBN. 32 — RI4-R45
| 470 OHM 1/4 5% CRBN. | 3 | REO, R63, REE |
| 510 OHM 1/6W 5% CREN. | 3 | —-R69,R72,R76 |
| 560 OHM 1/4W 5% CRBN, | 3 | —-RS7,R77,R78 |
| 1k OHM 1/4H 5% CRBN. | 6 | —-R68,R71,R73,R75,RO5, |
R86
| 2K OHM 1/4W 5% CRN, | 3 | R67,R70,R74 |
| 2.7K OHM 1/4W 5% CRBN, | 2 | R46, RAT |
4.7K OHM 1/4W 5% CRBN, 23 — R1,R2,R5-R7,R1O-R13, R4B-R50,852-R56,279, R81-84, R87
| 10K OHM 1/4W 5% CRBN. | 2 | RB, R4 |
82K OHM 1/4 5% CRBN. = 1 RB
| 1K OHM 9 PIN SIP | 4 | RM6-RM9 |
| 2.7K OHM 10 PIN SIP | 4 | RML-RMS |
| 4.7K OHM 10 PIN SIP | 1 | RMS |
| 1N6168 DIODE | 2 | 01,02 |
| 2N6123 NPN XSTR. | 2 | 01,06 |
| 2N4403 PNP XSTR. | s | Q2 |
MPSA70: PNP XSTR 6 — Q5-Q10
| TIP110 NPN XSTR. | 1 | Q3 |
| 20 MHZ COSC. | 1 | IC 4E |
| 7406 | 1 | IC 2k |
| 74AL$20 | 1 | IC 6D |
| 74F00 | 1 | IC 1F |
| 74F 08 | 1 | IC 14k |
| 74F 10 | 1 | IC 9E |
| T4F74 | 2 | IC 2£,10H |
| 74F 86 | 2 | 1 10F,7H |
| 74F 187 | 4 | IC 5C,6C,8C,66 |
| 74F 176 | 1 | IC 2H |
| 74LS00 | 2 | IC 148, 6F |
| 741802 | 1 | 1c 79 |
PART NO.
0986-00800-0300 0966-00800- 2800 0986-00800- 3000 0945-00816-0400 0986-00800-2000 0986-00800- 1100 0986-00800-0700 0986-00800-2700
100E-00005-0011
100E-00005-0016 100E-00005-0041 100E-00005-0051 100E-00005-0053 100E-00005-0054 100E-00005-0061
100E-00005-0068 100E-00005-0071 100E-00005-0079
100£-00005-0088 100E-00005-0112
102E-00004-0011 102E-00004-0020 102E-00004-0026
103E-00002-0005 104E-00001-0007 104E-00002-0006 104E-00002-0012 104E-00009-0001
0304-00804-0007
0986-00803-7 600
0A59-00803-0015
0A59-00803-0001 0A59-00803-0030 0AS9-00803-0002 0A59-00803-0003 0A59-00803-0031 0A59-00803- 0004 0A59-00803-0005
0304-00803-0010 0986-00803-7400
MONOBOARD A084-91787-C000 MO51-00114-Ci28
CROSS REFERENCE LIST: Page 2 of 3 (Rev. 22 Aug 65)
| DESCRIPTION | ary | DESIGNATION NO. | PART NO. |
| 74LS04 | 1 | IC 1K | 0986-00803-6900 |
| 74LS08 | 2 | TC 16,44 | 0986-00803-7300 |
| 741820 | 3 | IC 2F,3F,12H | 0986-00803- 1004 |
| 741832 | 3 | IC SF, 1H, 4k | 0986-00803-6100 |
| 74LS55 | Te td | 0459-00803-0026 | |
| 74LS74 | 6 | IC 12E, 15F,3K,5K,6K, 0986-00803-1005 |
18K
| 74LS66 | 2 | IC 13¢,8H | 0986-00803-9900 |
| 7415138 | 2 | IC 108, 26 | 0986-00803-6500 |
| 74LS153 | 2 | Ie 14¢,15D | 0A59-00803-0006 |
| 7418157 | 6 | IC 5A,3C,7C,7D, 11D, 3G 0304-00803-0021 | |
| 7418158 | 2 | IC 90,140 | (0A59-00803-0007 |
| 7415161 | 1 | Te 140 | 0986-00803- 1003 |
| 7415163 | 3 | 1¢ 30-5) | 0A59-00803-0008 |
| 74L5169 | 4 | IC 9G, 106,7K,9k | 0304-00803-0023 |
| 74L8173 | 3 | IC 86,8, 11K | 0459-00803-0009 |
| 74S 176 | 5 | IC 8D,10D, 12D, 14H, 13k 0304-00803-0024 | |
| 74LS175 | 1 | IC 43 | 0304-00803-0025 |
| 745196 | 8 | IC 13D,11E,13E,14£, | 0304-00803-0026 |
12F-14F, 146
| 74LS246 | 8 | IC BA-12A,4C,11C,2D | 0986-00803-4800 |
| 748245 | 3 | IC 1B, 8B, 108 | 0986-00803-6400 |
| 7418258 | 2 | IC 136, 13H | 0304-00803-0028 |
| 7418273 | 5 | IC 6A,7A,15B,15C,3H | 0986-00803-4700 |
| 7418283 | 2 | IC 76,60 | 0304-00803-0030 |
| 7418298 | 2 | IC 18, 12k | 0A59-00803-0010 |
| 7418367 | 1 | 10 IF | 0986-00803-7000 |
| 7415368 | 1 | IC 3E | 0A59-00803-0011 |
| 748374 | 6 | IC 12G,9H,11H,8J, 103, 0986-00803-4600 |
12d
| 74.8377 | 3 | IC 8F,12B,13B | 0AS9-00803-0012 |
| T4LS378 | 2 | IC 7F,9F | 0A59-00803-0013 |
| 74304 | 2 | It 1D,4F | 0986-00803-6600 |
| MMCOI1A HAL | 1 | IC 4G | 0986-00803-8900 |
| MMCOZB HAL | 1 | IC 6H | 0986-00803-9000 |
| MMCO3B HAL | 1 | IC 86 | 0986-00803-9100 |
| MMCO6 HAL | 1 | IC SH | 0986-00803-9200 |
| PACNS REY 1.0 PLA | 1 | IC 20 | A59R~26AAJ-BXHD |
| PACOUT REV 1.0 PLA | 1 | Ic 30 | A59A-26AAJ-AXHD |
| ROMCTRL REV 1.0 PLA | 1 | 1 134 | AS9A-26AAJ-CXHD |
| 2018 2Kx8 RAM 45NS | 4 | IC 116, 10k, 99, 119 | 0A59-00803-0028 |
| 2018 2Kx8 RAM SSNS | 1 | IC 10¢ | 0A59-00803-0029 |
| 6116 2kx8 RAM 120KS | 1 | 1¢ 118 | 0A59-00803-0027 |
| 6116 2kx8 RAM 15ONS | 2 | IC 6B, 9B | 0A59-00803-0014 |
| 93419 64x9 RAM | 1 | IC 4a | 0986-00803-9600 |
| 2808 | 1 | 1C 1c | 0304-00803-0041 |
| z80B cTC | 1 | 1 2 | 0304-00803-0040 |
| BGO 64K ROM/EPROM | 1 | IC 15A | ROM/EPROM CHART |
MONOBOARD A084-91787-C000 MO51-00114-C128
CROSS REFERENCE LIST: Page 3 of 3 (Rev. 22 Aug 85)
| DESCRIPTION | Qiy | DESIGNATION NO. | PART NO. |
| BG1 64K ROM/EPROM | 1 | TC 14B | ROM/EPROM CHART |
| FGO 256K ROM/EPROM | 1 | 1€ 8E | ROM/EPROM CHART |
| FGi 256K ROM/EPROM | 1 | IC 6E | ROM/EPROM CHART |
| FG2 256K ROM/EPROM | 1 | IC 5E | ROM/EPROM CHART |
| FG3 256K ROM/EPROM | 1 | IC 4E | ROM/EPROM CHART |
| PROGO 256K ROM/EPROM | 1 | IC 3B | ROM/EPROM CHART |
| PROG1 256K ROM/EPROM | 1 | IC 5B | ROM/EPROM CHART |
| 16 PIN IC SOCKET(.300) 1 | ICS 3E | 110E-00001-0003 | |
| 20 PIN IC SOCKET(.300) | 5 | ICS 56, 5H, 20,30, 13J | 110E-00001-0005 |
24 PIN IC SOCKET(.300) 7 ICS 10C,46,11G, 6H, 9) 110E-00001-0009 11d, 10K
| 24 PIN IC SOCKET( .600) | 3 | TCS 6B, 9B,11B | 110E-00001-0007 |
28 PIN IC SOCKET(.600) 10 ICS 4A,15A,3B,5B,14B, 110E-00001-0010 2C, 4E-6E, 8E
| 40 PIN IC SOCKET(.600) | 1 | ICS 1¢ | 110E-00001-00t1 |
| AUTO INSERT PIN | 18 | d2 | 0304- 00804-0009 |
TIN .025 SQ
| AUTO INSERT PIN | 22 | 33 | 0304-00804-0009 |
TIN .025 $Q
| AUTO INSERT PIN | 156 | 0304- 00804-0009 |
TIN .025 SQ
| AUTO INSERT PIN | 8 | us | 0304-00804-0009 |
TIN .025 SQ
| AUTO INSERT PIN | 10 | 6 | 0304-00804-0009 |
TIN .025 SQ
| AUTO INSERT PIN | Moat | 0304-00804-0010 |
TIN .045 SQ
| FERRITE BEAD | 13 | FBI-FB13 | 0316-00804-0002 |
| JUMPER | 4 | OW1-aW4 | 417£-00001-0003 |
| SWITCH PC. MTG. | 1 | SL | 0986-00804-3100 |
| 10 POS. DIP SWITCH | 1 | SW2 | 113E-00001-0004 |
| SNAP | 1 | MHQ3 | 0017-00007-0134 |
| PC BOARD | 1 | A080-91787-CO00 |
Released 6 Aug 85 CHM Changed 22 Aug 85 - Added ICS 3E CMM
BALLY/MIDWAY'S SARGE U.R. (MONOBOARD SYSTEM) U.R. #0888 ROM/EPROM PART NUMRERS
UNPROGRAMMED MONOBOARD A084-91787~C000 PROGRAMMED MONOROARD A084-91787-ABB8
MIDWAY PART NUMBER JUMPERS BBBA-22AAE-AXRD BBBA-22AAE=RXRD B88A-47AAE-CARN REBA=4 7TARE-DABD BS88A-47AAE-EABD BBBA-47AAE-FARD BBBA-47AAE-AABD B88A~47AAE~BARD
UNPROGRAMMED TURBO CHEAP SOUEAK A084~91779-A000 PROGRAMMED TURBO CHEAP SOQUEAK A084-91779=ABB8R
MIDWAY PART NUMRER BS8A-22AAE-CXRD BB8A-22AAE-DXRD
UNPROGRAMMED OPTICAL ENCODER DELUXE A084=-91794-A000
gumper | IN| JWT
REVISIONS
10/6/85 RELEASE FOR PRODUCTION
405 1-00B88-A008
SARGE U.R.
OPTION SWITCH SETTINGS
SITITIIITTATT STILT SWATCH NO. 2 = AT A 13 = LOCATED ON MONOROARD////S////SS/IS/TLISI//T1
DURING GAME PLAY: SW#1 SWAZ SW#3 SWE4 SWE5 SW#6 SWH7 Sw#8 SW#9 SW#I10 NOT NOT NOT NOT NOT NOT USED USED USED USED USED USED
NO FREE PLAY OFF FREE PLAY
1 COIN / 1 CREDIT 2 COINS/ 1 CREDIT 1 COIN / 2 CREDITS
NORMAL OPERATION FREEZE VIDEO
PART NO. M051-00888-A007
THE REMAINDER OF YOUR NEW GAME'S MOST COMMON OPTION SETTINGS ARE CONDUCTED DURING YOUR GAME'S SELF-TEST MONE
BALLY/MIDWAY'S SARGE U.R. (MONOBOARD SYSTEM) U.R. #0888 ROM/EPROM PART NUMRERS
UNPROGRAMMED MONOBOARD &£084-91787-C000 PROGRAMMED MONOROARD A084-91787=AB88
MIDWAY PART NUMBER B8B8A-22AAE-AXRD : BSBA-22AAE-RXRD BBBA=4 7AAE-CARD
‘ BB8A~4 7AAE-EARD B&BA-47AAE-FARD B88A-47AAE-AASD BSBA-47AAE~BARD
UNPROGRAMMED TURBO CHEAP SQUEAK A084-91779=A000 PROGRAMMED TURBO CHEAP SQUEAK A084-91779-AB88
MIDWAY PART NUMRER BBBA-22AAE-CXRD B88A-22AAE=DXRD
UNPROGRAMMED OPTICAL ENCODER DELUXE A084-91794-A000
= ie JWi bi.)
REVISTtONS
RELEASE FOR PRODUCTION
05 1-00B88-A008
SARGE U.Re
OPTION SWITCH SETTINGS
TIILITISTITITTTLTT TAT IS¥ATCH NOw 2 = AT A 13 = LOCATED ON MONOROARD/S///////I/LISILSIIIIS
DURING GAME PLAY: Swi SwW#2 SW#3 Swe4 Sw#5 Sw#6 SW7T Sw#8 SW SW#I0 NOT NOT NOT NOT NOT NOT USED USED USED USED USED USED
NO FREE PLAY FREE PLAY
we 4 COIN / 1 CREDIT OFF OFF 2 COINS/ 1 CREDIT ON OFF 1 COIN / 2 CREDITS OFF ON
NORMAL OPERATION :
FREEZE VIDEO
PART NO. 4051-00888-A007
THE REMAINDER OF YOUR NEW GAME'S MOST COMMON OPTION SETTINGS ARE CONDUCTED DURING YOUR GAME'S SELF-TEST MONE