CATHODE RAY TOMES

World Rally TM-391 3rd Printing Kit

World Rally (Atari Games, 1993) · Kit Manual · 32 pages · 46 sections · original scan

Page 1

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 2

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 3

Kit Installation Instructions

Universal conversion kit for two-player upright games

TM & © 1993 Gaelco. All rights reserved. Licensed to Atari Games Corporation,

Page 4

Copyright © 1993 by Atari Games Corporation. All rights reserved. No part of this publication may be reproduced by any mechanical, photographic or electronic process, or in the form of a phonographic recording, nor may it be stored in a retrieval system, transmitted, or otherwise copied for public or private use, without permission from the publisher. The game play, all graphic designs, this technical manual, its accompanying schematic diagrams, and the display manual are protected by the U.S. Copyright Act of 1976. This Act provides for substantial penalties for violating federal copyright laws. Courts can impound infringing articles while legal action is pending. If infringers are convicted, courts can order destruction of the infringing articles. In addition, the Act provides for payment of statutory damages of up to $50,000 per infringing transaction in certain cases. Infringers may also have to pay costs and attorneys’ fees and face an imprisonment of up to five years as well as fines of up to $250,000 in the case of individuals and up to $500,000 in the case of corporations. Atari Games Corporation will aggressively enforce its copyrights against infringers. We will use all legal means to immediately halt any manufacture, distribution, or operation of a copy of video games made by us. Anyone who purchases such copies risks forfeiting such a game.

Published by: Atari Games Corporation 675 Sycamore Drive Milpitas, California 95035 Printed in the U.S.A. 11/93 Produced by the Atari Games Technical Publications Department. Writing and Design: Andrea Dencker ‘World Rally Universal Kit

NOTICE RE.

NON-ATARI

PARTS

WARNING Use of non-Atari parts or modifications of any Atari game circuitry may adversely affect the safety of your game, and may cause injury to you and your players.

You may void the game warranty (printed on the inside back cover of this manual) if you do any of the following: © Substitute non-Atari parts, including cabinetry, in the game.

  • Modify or alter any circuits in the game by using kits or parts not supplied by Atari Games Corporation.
NOTE This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instruction manual, may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of Federal Communications Commission (FCC) Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area or modification to this equipment is likely to cause interference, in which case the user, at his own expense, will be required to take whatever measures may be required to correct the interference. If you suspect interference from an Atari game at your location, check the following:
  • All ground wires in the game are properly connected as shown in the game wiring diagram.
  • The power cord is properly plugged into a grounded three-wire outlet.
  • On games provided with an Electromagnetic Interference (EMI) ground plane, be sure that the game printed-circuit boards (PCBs) are properly installed on the EMI ground plane and that the end board is securely installed with all screws in place and tightened. If you are still unable to solve the interference problem, please contact Customer Service at Atari Games Corporation. See the inside front cover of this manual for service in your area.
Page 5

World Rally Universal Kit

SAFETY SUMMARY

The following safety precautions apply to all game operators and service personnel. Specific warnings and cautions will be found in this manual whenever they apply.

WARNING Properly Ground the Game. Players may receive an electrical shock if this game is not properly grounded! To avoid electrical shock, do not plug in the game until it has been inspected and properly grounded. This game should only be plugged into a grounded threewire outlet. If you have only a two-wire outlet, we recommend you hire a licensed electrician to install a three-wire grounded outlet. If the control panel is not properly grounded, players may receive an electrical shock! After servicing any part on the control panel, check that the grounding wire is firmly secured to the inside of the control panel. After you have checked. this, lock up the game. AC Power Connection. Before you plug in the game, be sure that the game’s power supply can accept the AC line voltage in your location. The line voltage requirements are listed in the first chapter of this manual, Disconnect Power During Repairs. To avoid electrical shock, disconnect the game from the AC power before removing or repairing any part of the game. If you remove or repair the video display, be very careful to avoid electrical shock. High voltages continue to exist even after power is disconnected in the display circuitry and the cathode-ray tube (CRT). Do not touch the internal parts of the display with your hands or with metal objects! Always discharge the high voltage from the CRT before servicing it. Do this after you disconnect it from the power source. First, attach one end of a large, well-insulated, 18-gauge jumper wire to ground. Then momentarily touch the free end of the grounded jumper wire to the CRT anode by sliding the wire under the anode cap. Wait two minutes and do this again. Use Only Atari Parts. To maintain the safety of your Atari game, use only Atari parts when you repair it. Using non-Atari parts or modifying the game circuitry may be dangerous, and could injure you and your players. Handle the CRT With Care. !f you drop the CRT and it breaks, it may implode! Shattered glass from the implosion can fly six feet or more. Use the Proper Fuses. To avoid electrical shock, use replacement fuses which are specified in the parts list for this game. Replacement fuses must match those replaced in fuse type, voltage rating, and current rating. In addition, the fuse cover must be in place during game operation.
CAUTION Properly Attach All Connectors. Make sure that the connectors on each printed circuit board (PCB) are properly plugged in. The connectors are keyed to fit only one way. If they do not slip on easily, do not force them. If you reverse a connector, it may damage your game and void your warranty. Ensure the Proper AC Line Frequency. Video games manufactured for operation on 60 Hz line power (used in the United States) must not be operated in countries with 50 Hz line power (used in Europe), If a 60 Hz machine operates on 50 Hz line power, the fluorescent line ballast transformer will overheat and cause a potential fire hazard. Check the product identification label on your machine for the line frequency required. ABOUT NOTES, CAUTIONS, AND WARNINGS In Atari publications, notes, cautions and warnings have the following meaning:
NOTE — A highlighted piece of information.
CAUTION — Equipment and/or parts can be damaged or destroyed if instructions are not followed. You will void the warranty on Atari printed-circuit boards, parts thereon, and video displays if equipment or parts are damaged or destroyed due to failure of following instructions.
WARNING — Players and/or technicians can be killed or injured if instructions are not followed.

iii

Page 6

‘World Rally Universal Kit

CONTENTS ILLUSTRATIONS

1 Installation How to Use This Manual Cabinet Equipment Requirements Tools Required... Inspecting the Kit Preparing the Cabinet for Assembling the Control Panel Installing the Foot Pedal ..... Connecting the JAMMA Harness... Installing the World Rally Game PCB Installing the Bezel, Decals, Labels, and Attraction Assembly .. Adjusting the Volum Setting the Coin and Game Options. Maximizing Earnings Game Play 2 Self-Test and Troubleshooting Introduction .. Entering and Exiting the Self-Test Monitor and General Status Screen .. Coin Settings Display. Game Settings Display. Control Test... Troubleshooting 3 Parts Illustrations See the List of Illustrations that follows.

4 Schematic Diagrams See the List of Illustrations that follows.

iv Figure 1-1

Figure 1-2

Figure 2-1 Figure 2-2

Figure 2-3

Figure 2-4

Figure 3-1 Figure 3-2 Figure 3-3 Figure 3-4 Figure 3-5 Figure 3-6

Figure 3-7

Table 1-1 Table 1-2 Table 1-3

Table 2-1 Table 2-2 Table 2-3 Locations of Control Panel Holes to be Drilled. 5 Locations of Foot Pe to be Drilled, + 1-6

Monitor and General Status Screen .... 2-2 DIP Switch 1 Display (Coin Option sone 2-2

Control Test Screen .

World Rally Universal Kit.... High/Low Gear Shifter Assembly Foot Pedal Assembly (Two Views)..... 3-4 360° Steering Wheel Assembly World Rally Game PCB Assembly JAMMA Filter PCB Schematic Diagram... JAMMA Filter PCB Assembly.

ABLES

Equipment Requirements Contents of World Rally Kit JAMMA Pin and Wire Connections 1-4

DIP Switch 1 Settings (Coin Settings)... 2-3 DIP Switch 2 Settings (Game Options)... 2-4 Troubleshooting Table.

Page 7

CHAPTER 1

Installation

How To Use THis MANUAL

|. HE WORLD RALLY™ conversion kit is

a two-player alternating game for up-

right cabinets. If you own upright

Pole Position® games previously made by

Atari, Inc., we have provided detailed instruc-

tions for installing this kit into those games.

These instructions are published in a supple-

ment to this manual, part no.

CO-391-02. Contact your Atari

Games distributor if you would

like a copy of this supplement. ¢

This manual provides information for installing, testing, and troubleshoot-

ing the World Rally” conversion kit. ¢ Chap-

ter 1 describes how to install the World Rally

kit in your cabinet. This chapter also de-

scribes game play. ¢ Chapter 2 contains selftest procedures and a troubleshooting table. The self-test is important in the World Rally

game. You can troubleshoot the

PC boards, main circuits, and

controls using the screens in the

self-test. @ Chapter 3 contains

the kit parts illustrations.

Page 8

Installation

WARNING To avoid electrical shock, unplug the cabinet while installing the kit. After installation, plug the game only into a grounded 3-wire outlet.

Cabinet Equipment Requirements

WARNING For safe use, you must install this World Rally kit in a standard Atari Games “family” cabinet, or in any cabinet that has received Underwriters Laboratories listing.

Table 1-1 lists the equipment required in the cabinet into which you are installing the World Rally kit.

CAUTION Do not unplug or plug in the World Rally game printed-circuit board (PCB) edge connector while the power is on. You could seriously damage the PCB.

Specification

Color RGB monitor Separate positive horizontal and vertical sync or negative composite sync Horizontal mounting Horizontal frequency: 15.750 KHz Vertical frequency: 60 Hz Video input: 1V to 3V peak-to- Video Display

peak positive polarity

Control! Panel Metal only

Speaker 89, 10W

Coin Counter +5 VDC or +12 VDC

Power Cord Three-conductor with ground Power Supply +5 VDC + 0.25V @5.0 amps minimum

+12 VDC @ 1.0 amp

Table 1-1 Equipment Requirements World Rally Universal Kit

Tools Required

© Drill with a “4inch and %-inch drill bits

° Phillips screwdriver ¢ Flat-blade screwdriver

© Socket wrench set and ratchet

© %inch hex wrench

¢ Wire cutters and strippers

Qty.

1JAMMA Filter PC Board Assy.A047292-01
1Product |.D. Label038158-01
1FCC Compliance Label039450-01
1FBI Warning Label042452-01
1Black Bezel for Kits049774-01

1 %e-inch Polycarbonate Control Panel Cover 051656-01

2Side Panel Decal051932-01
1Attraction Film051933-01
1Control Panel Decal051934-01
1Instruction Label051937-01
440-inch |.D. Split Ferrite Beads141026-003
1Snap-Action Switch160044-001
1High/Low Gear Shifter Assy.171088-001
1Single Foot Pedal Assy.171122-0001

1 360° Steering Assy. with Mounting Pod and Hardware 171123-0001

1World Rally Game PCB Assy.155035-001

4 -281 |.D. x 1.25 0.D. x .059 Thick Flat Washers 175002-007

4#10 Flat Washers175014-1040
4#10-24 Zinc NutWasher Assemblies—177026-0040
4#1/4-20 Nut/Washer Assemblies177026-0044
2#10 Wire and Cable Ties178032-002
1Red Button Assembly178237-001

1 Biack “Start” Indicator Plate with Backing Strip 178283-011 2 %inch Straight PCB Standoffs with Adhesive (for JAMMA Filter Bd.) 178373-0108

4#10-24 x %inch Long Carriage Bolts75-5112B

1 World Rally Universal Kit Installation Instructions TM-391

Note: A JAMMA harness is not included in this kit. If your game cabinet does not already have a JAMMA hamess installed in it, you can order this harness from Atari Games Customer Service. Also, packaging materials are not listed above.

Table 1-2 Contents of World Rally Kit

Page 9

World Rally Universal Kit

© Straight edge © Squeegee

  • X-ACTO™ knife © Insulated wire connectors (if you are installing a new JAMMA harness) ¢ Carbon paper
  • Saber saw
  • File
  • Bandsaw
  • Tape or glue

Inspecting the Kit

Check to see that you have all the parts listed in the kit parts list in Table 1-2. If any part is missing or damaged, contact your distributor with the World Rally kit serial number, part number, and description of the missing or damaged parts, and date received.

CAUTION Legally distributed World Rally™ game PCBs have a small holographic “AAMA” label on them. If your game PCB does not have such a label, contact your Atari Games distributor before installing this kit.

Preparing the Cabinet for the

Kit Installation

WARNING To avoid electrical shock, unplug the cabinet while installing the kit. After installation, plug the game only into a grounded 3-wire outlet.
  • Turn off power to the game, and unplug the power cord.
  • Remove the following from the cabinet: © Existing PCBs © Game harness, if it is not Japan Amusement Machinery Manufacturers Association (JAMMA)— compatible
  • Control panel decals, labels, and controls
  • Side decals, graphics, and adhesive. If the cabinet sides are damaged, repair them before putting on the new decals. Installation
  • Video display (monitor) shield, display bezel, attraction shield, and marquee.
  • Wipe down and vacuum the cabinet. Paint the cabinet, if required.

Assembling the Control Panel

Parts Needed for this Kit

To assemble the control panel, you need to decide on where to cut the control panel holes. Refer to Figure 1-1. Create a template sheet from that illustration. You will also need the following parts from the kit:

  • Clear cover for the control panel © Control panel decal
  • Red button assembly
  • Snap-action switch ¢ “Start” indicator plate © High/low gear shifter © Steering wheel with mounting pod and hardware ¢ Four #10 flat washers, #10-24 x %-inch-long black carriage bolts, and #10-24 nut/washer assemblies for the gear shifter

Installing the Parts

  • Using carbon paper, transfer the design from the template to the control panel. Save the template.
  • Drill four %-inch holes in the metal control panel for the gear shifter mounting bolts.
  • Using a saber saw, carefully cut out the large hole for the gear shifter. Deburr the sharp edges with a file. 4, Drill four .343-inch holes for the four mounting bolts of the steering pod.
  • Drill two 1.187-inch holes — one for the start button and one for the center of the steering wheel assembly.
  • Lay the plexiglass cover over the top of the control panel and mark the outside shape of the panel on the plastic. Also mark the button hole as close as possible to the locations shown on the template. Lastly, mark the positions of the four holes that will be used for securing the cover to the control panel. These four holes can be placed anywhere near the corners — wherever space permits.
Page 10

Installation World Rally Universal Kit

Solder Side Component Side

Color’PiinignalColor’
Brown?POWER GNDA1POWER GNDBrown?
Brown?POWER GNDB2POWER GNDBrown?
Red+5V DCc3+5V DC.Red?
Red?+5V DCD4+5V DCRed?
OrangeNot UsedE5Not UsedOrange
Yellow*+12V DCF6+12V DCYellow*
_KeyH7Key=
Violet/White®COIN CTR 2J8COIN CTR 1Blue/White®
_Not UsedK9Not Usedad
WhiteSPKR -L10SPKR +Brown
_Not UsedM1Not Used—
GreenVIDEO GREENN12VIDEO REDRed
BrownVIDEO SYNC (neg. composite sync)P13VIDEO BLUEBlue
—Not UsedR14VIDEO GNDBlack’
—Not Useds15SELF-TESTWhite®
OrangeCOIN SwW2T16COIN SW1Yellow
=Not Usedu17PLYR1 STARTWhite/Black*
—Not Usedv18Not Used=
—Not Usedw19Not Used=
_Not Usedx20Not Used—
—_Not UsedY21Not Usedam
=Not Usedz22ACCELERATORWhite/Green”®
-Not Useda23SHIFTERWhite/Blue”
=—Not Usedb24Not Used_—
=Not Usedce25Not Used_
Grey/White®STEERING DIRECTIONd26STEERING CLOCKViolet’?
Black/WhiteSWITCH GNDe27SWITCH GNDBlack/White
Black/WhiteSWITCH GNDt28SWITCH GNDBlack/White

Footnotes

1 The colors listed are for reference only. They are the colors used on the JAMMA harness available from Atari Games 2 Connect to the SV GND (RTN) terminal on the power supply. However, if you have 12V GND, connect one of the wires at pin 1, 2, A, of B to the 12V GND terminal. If your power supply has a ~ Sense terminal, connect one wire to the ~ Sense. 3Connect to the +5V terminal on the power supply. However, if your power supply has a + Sense terminal, connect one wire to the + Sense Connect to the +12V terminal of the power

supply. If your coin counter(s) require 12V,

also connect to the + side of the coin

counter(s), Sif you want to install a second coin counter, connect this wire to one side of the right 12V coin counter. Note: Do not use 24V counters. Connect the + side to +5V or +12V on the power supply, as appropriate. SConnect this wire to one side of the left 12V coin counter. Note: Do not use 24V counters. Connect the + side to +5V or +12V on the power supply, as appropriate. 7Note that the Worid Rally Game PCB was modified at the Atari Games factory to ground this pin. If this wire has become damaged and the video signal is no longer grounded, the monitor will display a jumbled video image. 8Use this wire if you want an external self-test switch. However, the kit already has a selftest switch on the game PCB. (If you connect an external self-test switch, turn off the ‘switch on the PCB. Connect the wire to the N.O. terminal on the external self-test switch. Connect the common terminal of the switch to a GND wire.) Connect this wire (white/black) to the N.O. terminal on the start button. Connect the common terminal to a switch ground wire. 10 Connect this wire (white/green) to the yellow wire supplied on the foot pedal assy. Con- Nect the black wire on the foot pedal to a switch ground wire. Secure the green safety ground wire to a bare metal AC ground source. 11Connect this wire (white/blue) to the N.O. terminal on the shifter. Connect the common terminal of the switch to a switch ground wire. NOTE: Improper connection of the shifter will cause it to work backwards, affecting game play and earnings! 12Connect the greyMWhite wire (steering direction) to the white wire supplied with the steering assy. Connect the violet wire (steering clock) to the grey wire supplied with the steering assy. Connect the red wire on the steering assy. to +5V and the black wire to switch ground.

Table 1-3 JAMMA Pin and Wire Connections

1-4

Page 11

‘World Rally Universal Kit Installation

NOTE The four holes in the corners for securing the control panel cover are not shown in this i- 6.36 - B.00 4 lustration. Drill these holes Wherever space permits. /—\sl8T DIA (2x) vee DIA (4x)

/ \ / \; Low

a:id:“9?———|——

| | 32 308

  • wee te \ q
Red StartSteering|i

Button Wheel Pd

4@oF4=

N i ; f Ne aoe ——u

BBB

  • elo a i Suggested distance from the front of the con- J trol panel. Check that the controls have sufficient clearance before cutting any holes.

Figure 1-1 Locations of Control Panel Holes to be Drilled

  • Using a bandsaw, cut the control panel cover to its correct outside shape.
WARNING Wear safety glasses when drilling the plastic control panel cover. Use care to avoid shattering or chipping the plastic.
  • Tape or glue the template to the plexiglass cover. To start the saber saw cut, drill a 4-inch hole inside the steering wheel hole, the gear shifter cutout, and the button hole.
  • Saw out the large hole for the shifter and the button hole.
  • Drill the four 4-inch holes that will be used to mount the cover to the control panel and the %inch bolt holes to mount the shifter.
  • To prevent injury, carefully deburr all the edges of the plexiglass cover.
  • Install the control panel decal on the control panel. Use a sharp X-ACTO knife to trim the outside edge and to cut out the holes for the controls.
  • Install the cover on the control panel with the four ¥%-inch-long carriage bolts, washers, and nut/washer assemblies.
  • Install the steering wheel pod using the 1/4-20 hardware supplied with it.
  • Install the red button assembly with its “Start” indicator plate and snap-action switch.
  • Install the gear shifter with its #10-24 nut/washer assemblies and %-inch-long carriage bolts. For maintenance and servicing information on the controls, refer to Chapter 2 of this manual.

Installing the Foot Pedal

Parts Needed from this Kit

To install the foot pedal on the lower front of your game cabinet, you need the following parts: © Fooi pedal assembly ¢ Four fender washers and nut/washer assemblies

Page 12

Installation ‘World Rally Universal Kit

1.

Installing the Parts Connecting the JAMMA cations shown in Figure 1-2 of this manual. Using Harness

Draw a template using the hole dimensions and lo-

carbon paper, transfer the foot pedal mounting pat- 1. If your game cabinet does not already have a JAMtem from the temple to the. cabinet. MA harness, install a JAMMA harness in the cabi- Drill four %-inch corner holes and a 1%-inch center net. To purchase a JAMMA harness, contact the hole in the cabinet front. Atari Games Customer Service office closest to you. Feed the pedal harness through the large center 2. Install the two pairs of split beads on the harness hole. Insert the foot pedal’s threaded studs into the as close to the PCB edge connector as possible. four small corner holes. Hold the beads on the harness with the two tie From the inside of the cabinet, install the four fend- wraps included in the kit.

1-6 er washers and nut/washer assemblies onto the threaded studs of the pedal.

Z FOOT Fans

\.250 DIA

B15 DIA (Ax) NE Fiwer

l \ oo Zoo : {

cok

jee Suggested distances from the inside

550 | — edge of the side panel and the floor.

L- 4.00 4 NOTE: If your cabinet has a thicker

lower front panel, you will need to

-— 23.15 REF counterbore each .375-inch-diameter hole on the inner side of the panel.

Figure 1-2 Locations of Foot Pedal Holes to be Drilled

Page 13

‘World Rally Universal Kit

CAUTION You must install the split beads and the JAMMA Filter PCB on the JAMMA harness to meet FCC requirements. (These parts are included in the kit.)
  • Using Table 1-3 for wiring information, connect the JAMMA harness to existing component harnesses. Use crimp splices or butt soldering.
WARNING Do not simply tie the wires together. If you do, you could cause intermittent problems, loose connections, oxidation, or a fire.

Connecting Power Wires

  • Connect the wires on the JAMMA harness to the wires for the power supply, as shown in Table 1-3. The World Rally kit requires +5V and +12V. The -5V is not needed and should not be used. Tie off any other voltage wires on the power supply besides +5V, -5V, and +12V. There is more than one wire for each voltage in the JAMMA harness. Use more than one wire for each voltage (connecting them as described in Table 1-3) so that the power wiring does not overload and burn.

Connecting Video Display Wires

NOTE The JAMMA harness provides only negative composite sync.

Connect the wires designated for the red, green and blue video guns along with the sync and ground wires, according to Table 1-3.

Connecting Coin Door Wires 1, Connect the wires on the JAMMA harness to the coin switches and meter according to Table 1-3.

  • Connect one terminal of the door lamps to one of the BK/W wires. Connect the other terminal of the door lamps to the R wire supplying +5V.
NOTE Do not use -5V for the coin door lamps. Tastallation

Some games have separate power supply outputs for the coin door lamps. If you choose to use these outputs, make sure you connect both terminals of each lamp to the terminals on the power supply.

Connecting the Control Wires Connect the gear shifter, foot pedal, steering wheel, and button harnesses to the JAMMA harness using crimp splices or butt soldering, according to the information in Table 1-3.

Grounding the Cabinet Find the ground lead (green) of the 115V input power line. Connect this lead in daisy-chain fashion to a bare metal part of the coin door, the control panel, the foot pedal, the video display, and the power supply. This AC ground must be of #18 AWG wire or larger.

WARNING For the safety of players, you must connect the green ground wire as indicated above.

Checking the JAMMA Connections Before plugging in the game PCB, turn on the power to the game, and check +5 Volts on pins 3, 4, C, and D of the JAMMA connector; +12 Volts on pins F and 6; and —5 Volts on pins E and 5. Check that the video display and the attraction lamp have power. Now turn off the power to the game.

Installing the World Rally

Game PCB

  • After you have checked the power on the JAMMA connector (above), install the World Rally game board in the cabinet. Use the four screws and standoffs supplied with the game board to mount it onto the wood cabinet surface.
  • Plug the JAMMA Filter PCB into the game board. Install the %-inch standoffs with adhesive to support the Filter PCB.
  • Connect the JAMMA harness connector to the Filter PCB. 4, Secure the JAMMA harness away from the PCB with cable ties.
  • Turn on the power to the game. Check that the game PCB functions. If a video picture is not present, see Chapter 2.
Page 14

Installation

Installing the Bezel, Decals,

Labels, and Attraction

Assembly

Installing the Display Bezel Find the cardboard display bezel in the kit. This bezel can accommodate both 19-inch and 25-inch video displays. Follow the instructions on the back of the bezel, and cut the hole and outside edges as required. Then find the game instructions label in the kit, and adhere that label to the bottom center of the bezel.

Installing the Product ID and FCC Label Place the product ID label (part no. 038158-01) and FCC compliance label (part no. 039450-

  • on the back of the cabinet.

Installing the Side Panel Decals Find the side panel decals in the kit. Wet the left and right side panels of the cabinet with slightly soapy water. Then position the decals on the side panels of the cabinet. Remove any wrinkles in the artwork using a squeegee. Allow the sides to dry.

Installing the Attraction

Find the World Rally attraction film in the kit (the attraction shield should be reused from your cabinet). Using the existing shield as a template, cut the film to size, if necessary, Install them in the cabinet attraction assembly.

Adjusting the Volume

This game has a volume control potentiometer on the game printed-circuit board. To adjust the volume, turn the knob located near the PCB’s edge connector. ‘World Rally Universal Kit

Setting the Coin and Game Options

Set the coin and game options in the self-test. See Chapter 2 for information about the option settings.

Maximizing Earnings

For maximum earnings, regularly maintain your World Rally game. When you set up the game and when you collect money, use all the screens in the self-test procedure — especially the Control Test.

Game Play

This section describes the theme of the World Rally game and the game play features.

Introduction

World Rally™ is a road rally-themed driving game. Licensed by Gaelco of Barcelona, Spain, it is suitable for both street and arcade locations. World Rally is a one- or two-player alternating driving game. Controls include a steering wheel on a mounting pod, a high/low gear shifter assembly, and an accelerator pedal.

Game Play Description Players select one of four rallies to start, each progressively more difficult than the one before. A rally is’ composed of three stages, offering a variety of different track layouts and road surfaces. Asphalt, dirt, night driving and snow-covered roads require players to adjust their driving skills accordingly. Players maneuver their way through hairpin curves, jumps, bridges, puddles, and other obstacles. Completing each stage within the 60-second time limit allows players to advance to the next stage for free. After the finish of each stage, and at the completion of all 12 stages, players’ times are displayed and compared with other top drivers.

Page 15

{ CHAPTER 2

Self-Test and Troubleshooting

INTRODUCTION

J; HIS CHAPTER contains a

description of the self-test

. and two troubleshooting

tables for your World Rally” game.

Use the self-test procedure to check

the condition of the game circuitry

and controls. @ You will see the

self-test information on the video display. You and exp! do not need any additional equip-

ment to perform the self-test. You

should perform the self-test when

you first set up the game, each time

you collect the money, or when you

suspect game failure. ¢ This chap-

ter shows the screens in the self-test

lains each of the tests.

Page 16

Self-Test and Troubleshooting

Entering and Exiting the

Self-Test

To enter the self-test, push switch toggle 1 on DIP Switch 2 to the on position (located on the game PCB). Then turn the power to the game off and on again. See Figure 3-5 of this manual, which highlights the locations of DIP Switches 1 and 2. Exit the self-test by returning this switch to the off position. Then turn the power to the game off and on again.

Monitor and General Status Screen

Use this screen to see the monitor colors and the general status of the electronics (see Figure 2-1).

Monitor Test

The color strips in the center should be four bands (green, red, blue, and black/white from top to bottom), each with a color scale of 15 blocks ranging from dark to bright, left to right. If the screen does not match this description, adjust the video display as described in the video display manual.

Electronics Status

The four lines at the bottom of the screen show the version of the software, and the status of the RAM, ROM, and coprocessor. Advance to the next screen by pressing the Start button.

aes

Figure 2-1 Monitor and General Status

World Rally Universal Kit

Coin Settings Display

Use this screen to see how all the dual-inline-package (DIP) switch toggles on DIP Switch 1 on the game PCB are set. You can view and change the coin options on this screen, shown in Figure 2-2. The coin option settings are explained in Table 2-1. To change a setting, slide the appropriate toggle on DIP Switch 1 to on or off. The screen will immediately display the change in status. Advance to the next screen by pressing the Start button.

Dip

6 8 O ed

O o ed

a o

ee Pla O

Figure 2-2 DIP Switch 1 Display (Coin Option Settings)

Game Settings Display

Use this screen to see how all the DIP switch toggles on DIP Switch 2 on the game PCB are set. You can view and change the game options on this screen, shown in Figure 2-3. The game option settings are explained in Table 2-2. To change a setting, slide the appropriate toggle on DIP Switch 2 to on or off. The screen will immediately display the change in status. Advance to the next screen by pressing the Start button. yee

Page 17

World Rally Universal Kit

Free Play 1 Off 10n Switch Settings Self-Test and ‘Troubleshooting

Result

Nov Yes

Start/Continue Setting 2 Off T credit to start/1 credit to continue 20n 2 credits to stari/1 credit to continue ¥

Game Cost6 Off7 Off8 Off1 coin for 1 creditFor SW1 or left mechanism
6 Off7 Off80On1 coin for 2. credits
6 Off70n8 Off1 coin for 3 credits
6 Off70n8 On1 coin for 4 credits
6 On7 Of8 Off1 coin for 5 credits
6On7 Off80On1 coin for 6 credits
6On70n8 Off2 coins for 3 credits
60On70n80On3 coins for 4 credits
Game Cost3 Off4 Off5 Off1 coin for 1 creditwFor SW2 or right mechanism
3 Off4 Off5On2 coins for 1 credit
3 Off40n5 Off3 coins for 1 credit
3 Off40n5On4 coins for 1 credit
30On4 Off5 OffS coins for 1 credit
30n4 Off50On6 coins for 1 credit
30On40On5 Off3.coins for 2 credits
30n40On5On4 coins for 3credits

v Manufacturer's recommended settings.

Table 2-1 DIP Switch 1 Settings (Coin Settings)

Dip

8 D a

6 O

4 ontrol Op

Ad ound

Positio prig

Figure 2-3 DIP Switch 2 Dispiay (Game Option Settings)

Control Test

Use this screen to check all the coin switches, control panel switches, steering wheel, and foot pedal in this game (see Figure 2-4).

‘Ignore the S6 setting. Setting it to either 1 Joystick or 2 Joysticks is irrelevant, because this kit does not use joysticks. To check the functioning of each switch, activate it and watch the corresponding graphic change.

NOTE Player 1 is the start button. F1 represents the foot pedal, and F2 is the gear shifter. The Player 2 start button and the three graphics below it are not used by the game software. Coins 1 is the left coin mechanism, and Coins 2 is the right one.

If the messages or graphics do not appear correctly, check the harness connections, switches, steering wheel, and foot pedal. Advance to the attract mode by simultaneously pressing the foot pedal and the start button. Permanently exit the self-test by moving switch toggle 1 on DIP Switch 1 to the off position. Then turn the power to the game off and on again. The game will now stay in the attract mode,

Page 18

Self-Test and Troubleshooting ‘World Rally Universal Kit

Option Result

Game Difficulty7 Off8 Off1 (Normal) ¥
7 Off80On2 (Easy)
70n8 Off3 (Hard)
70On80On4 (Hardest)
No, of Joysticks Installed6On1 joystick

6 Off 2 joysticks (Either of the S6 settings is irrelevant for this kit, so ignore how this switch is set. This kit does not use joysticks.)

Driving Control Installed4 Off5 OffJoystick
4 Off5On270° steering wheel (potentiometer)
40n50On360° steering wheel (optical sensor) ¥
Sound During Attract?3 OffNo

30On Yes¥

Type of Cabinet20nCocktail table

2 Off Upright game ¥

Self-Test Mode On1 OffNov

10n Yes (You must power off the game before it will enter the self-test mode or stay in the attract mode.) v Manufacturer's recommended settings.

Table 2-2 DIP Switch 2 Settings (Game Options)

Control Test

Wheel

Player? &

F

Coins 1 OFA

Coins 2

Troubleshooting

Table 2-3 (troubleshooting) in this chapter can help you pinpoint problems in your game. This table lists possible sources of problems in various parts of the game.

Player? &

Press P1 and F1 to Exit

Figure 2-4 Control Test Screen

Page 19

World Rally Universal Kit Self-Test and Troubleshooting

Problem Suggested Action Coin Mechanism Problem 1. Check the wiring to the coin switch and counter.

  • Test the coin switch with the sound test screen in the self-test.

Game Play Problem . Check the harness and connectors.

  • Perform the self-test.
  • Check the voltage levels on the PCB.

Control Problems . Has the steering wheel, gear shifter, or foot pedal been lubricated? If not, lubricate it. Refer to Figures 3-2 through 3-4 for exploded parts illustrations. . Check the harnesses and connectors. . Check the switches and the optical sensor on the steering wheel by using the Control Test screen in the self-test procedure. . Ifyou took the control apart, have you reassembled it correctly? . Make sure all the parts on the controls are in good repair. Repair or replace parts. on

as

Sound Problem 1. Is the speaker volume turned up? (Volume is adjusted on the game PCB.)

  • Check the voltage on the game PCB edge connector.
  • Check the wiring from the PCB to the speaker.
  • Check the voltage level to the PCB.
  • Replace the speaker.

Video Display Problem Screen is dark. . Isthe game plugged in? . Is the game turned on? Are the connections good? . Is the line fuse good? . Is the display brightness turned up? . Are the edge connectors on the game PCB and JAMMA Filter PCB tightly connected? . Check all of the items below. If you answer no to any question, you have a problem with the video display, not with the game circuitry. See your video display service manual. a. Do you have power to the video display? b. Are the video display’s filaments lit? c. Do you have high voltage to the video display?

  • Are the voltage levels to the video display PCB correct? (Power voltage is 100 VAC or 110 VAC, depending on the type of video display. Video signal voltage is 0.5 to 3.5 Volts.)
  • Ifthe level is not correct, check the connectors and the harness. OPaaons

=

Only a colored screen appears. You probably have a serious RAM problem.

Display area wavers or 1. Do you have correct power voltage to the video display PCB? is too small. 2. Do you have correct high voltage to the video display? Picture is wavy. 41. Is the monitor ground connected to the monitor?

  • Are the sync inputs connected properly?

Picture is upside down. Check DIP Switch 2, taggie 2, on the game PCB. This toggle shouid be in the off position for a normal screen in an upright game. Another possibility is if you serviced the display, you may have connected the wires incorrectly. Switch the horizontal or vertical yoke wires on the display.

Convergence, purity Use the first screen in the game's self-test to adjust the video display. Use the or color problems. adjustment procedures in your video display manual. as Picture is not centered. Use the centering procedures in your video display manual.

Table 2-3 Troubleshooting Table

Page 20

Self-Test and Troubleshooting

2-6

NOTES

World Rally Universal Kit

Page 21

CHAPTER 3

~ Parts Illustrations

» HIS CHAPTER provides information

you need to order replacement

parts for your kit. All the common

hardware parts sold with this kit, such as

screws, nuts, washers, and so on,

are included in these parts

illustrations. In addition, the

JAMMA Filter PCB schematic

diagram is included in this ==

chapter. @ When you order parts, give the part number, part name, the number

of this manual, and the serial number of your

kit. With this information, we can fill your

order rapidly and correctly. We hope this will

create less downtime and fy | | more profit from your games. i Atari Games Customer Service

phone numbers are listed on

the inside front cover of this

Page 22

Parts Illustrations World Rally Universal Kit

Figure 3-1 World Rally Universal Kit A051940-01 B

Parts List

Quan- Quan-

tityDescriptionPart No.tityDescriptionPart No.
1JAMMA Filter PC Board Assy.A047292-014.281-Inch LD. x 1.25 O.D. x .059-
1Product LD. Label038158-01Thick Flat Washers175002-007
1FCC Compliance Label039450-014#10 Flat Washers175014-1040
1FBI Warning Label042452-014#10-24 Zinc Nut/Washer Assemblies 17026-0040
4#1/4-20 Nut/Washer Assemblies177026-0044

Black Bezel for Kits 049774-01

%e-Inch Polycarbonate Control2#10 Wire and Cable Ties178032-002
Panel Cover051656-011Red Button Assembly178237-001
2Side Panel Decal051932-011Black “Start” Indicator Plate with
1Attraction Film051933-01Backing Strip178283-011

2 ¥-Inch Straight PCB Standoffs with

1Control Panel Decal051934-01Adhesive (for JAMMA Filter Bd.)178373-0108
1Instruction Label051937-01
4-40-Inch LD, Split Ferrite Beads141026-0034#10-24 x %Inch Long Carriage Bolts 75-5112B
1Snap-Action Switch160044-0011World Rally Universal Kit Installation

Instructions TM-391

:High/Low Gear Shifter Assy171088-001Note: A JAMMA harness is not included in this kit. If your
1Single Foot Pedal Assy.171122-0001i"hi[AMMA bne
1360° Steering Assy. with Mountinggame cabinet dosnne ready evenanes 1
Pod and Hardware17123-0001stalled in it, you can order this harness from Atari Games

Customer Service.

1World Rally Game PCB Assy.155035-001

Also, packaging materials are not listed above.

Page 23

World Rally Universal Kit Parts Illustrations

99-215004 Rubber Stop (2 places)

99-215003 Microswitch 99-215002 w/Actuator Cover Plate _

99-215001 Knob and Shaft

Figure 3-2 High/Low Gear Shifter Assembly 171088-001

Page 24

Parts Illustrations World Rally Universal Kit

99-215115 Top Pedal

Figure 3-3 Foot Pedal Assy. (Side View) 171122-0001

3-4

Page 25

Parts Illustrations World Rally Universal Kit

99-215112 [e) #4-40 Screw (2 places)

99-215107 Base

99-215113 Spring 99-215003 Microswitch

99-215114 99-215108

Shaft = Switch Bracket

99-215111 =| #8-32 Screw

99-215109 ane 0 bpd (2 places) (4 places)

Figure 3-3 Foot Pedal Assy. (Bottom and Top Views) 171122-0001

Page 26

Parts Illustrations ‘World Rally Universal Kit

99-215101 go-21s103 99-215102 Lock Nut This bracket is not Gear Washer 7

used. It is replaced by: se-2isi01 Sys 9.215098

99-215116 99-215104 a yeerow Mounting Pod a

99-215106 ap \ 99215100 99-215092 Bolt Shaft

99-215118 a0 y Encoder Wheel

a 99-215099 Screw

99-215091 Brack Collar chet 99.215097 99-215090 99-215095 Encoder PCB 99-215098

Washer g9-215094 Gear Plate Screw

Bushing

99-215086 Three-Spoke Steering Wheel

99-215089 Lock Nut

99-215087 Screw

99-215088 Horn Cover O

Figure 3-4 360° Steering Wheel Assembly 171123-0001

3-6

Page 27

a World Rally Universal Kit

= {+ ey earswidue [_carpwcqus[ wsisvred

seesiezdem | meswedd seze teen Are both DIP switch locations. Use for setting game and coin options.

Eee: A syzsie sl sis Wei Ceie ia

visage: = ql

a4 i ld m [|p zm [8 sie ete + W, gq =n. a = |& qu EF Parts Illustrations

JAMMA ann:

N

Figure 3-5 World Rally Game PCB Assembly 155035-001

3-7

Page 28

Parts Illustrations

FROM GAME BOARD

3 O——* jis 4 O-—» Juesy S$ O——# tw & O a0 Juetey TO KY 8 O——« JLCNTRE 9 O——* Juke 10 O——# yispKni~ 1d O——» JinupeN 12 O—# JioREEN 13 O-—— JLSYNE 14 Ow Jas RY 15 O-—* LVL 16 0-8 JURrIN, 17 O—— JUS TORT 18 O-—« Jiupen 19 O-——= JLpOKNZA 20 O-—— JULY 128 24 O-——* ART? 22 O——-# LF TREZ 23 O——= Jive! 24 O——# I bUHNEB 25 O—= JiLEITZ3, 2 O——# HRTZB 27 O-—# GND 28 O——-= CND 8 O—s CRD 5B Oe cnn CO 9 Jiesy DO—# sissy Oe ey Oo sey oO ker Oe SENTRA O—* J1LorKt Os s1sPKR I+ Oma SAUL Oo" RED Os vine, O—— JLVTDGND Oe JASLITST Oa COIN Oo sasak Ts Oo uP o——= spot Oa JLEFTIA oa RTI Oe ree oe uP BS O——# J:0THNIB. CC O——# JSLEFTID, 0p O——s JR TLE. FE FF Buaxcccamsvzzrncran

3-8 cou JESSY 9m $n Je) 200nF

JL=5Y 8 ——# S50

Jae12y «———|— pe Jy

2200PF

JACI @ oi TR 2200PF Eoq nee LOCKE oo e200rr

2p00PF cay

Np SADC TE 2n00°F —~# JSPKRI-

= JoREEN e70PF 633 JAS ING we] arpa —a asin rp 270pr

JATILT &

JARCOIN —a JRCOIN

z200PF C37 np —e sine 2200°F JASTART2 e—-

cx stunner span 2200°° aq 2002 Hamar Jonnie > 22000

JULEFTEA JLEFTER

ARTE rn Jere

oa JAP REQ #— r ePnOPF cng

JAU02 = wuee

iz L arbaid i

<< JpoKNAN

—# JLEFTED = os enone

2 apTen World Rally Universal Kit

suv ie aps she rece

20°F cy, ca. Jose

Jisi2ye——

20°F cp J8L0¢K @—— fre Lot z To c JESPRRL =~ ssexra+ = zener cg

JteuDe age ue a 2zoore + ¢ ae Rep @r po co 2708 exp Jin.ue ——— a nm BLUE ob ezore

cat JAVIDOND =, sasurtst e=——[-——— ma ist tsr zecorr

sLc0n er pen co

ssstamtt + sirens LE eoor

cis SUPA 9am UPA Tr 22n0PF yy, JADORNLA @=—— ais Alea 2 220oPr

rs? JALEF 1g es 2200°F 49 kia — nce kde JLEFTAR

= oRTIA PE

ra = JAP TRE eo

Yo PRO0T U0 = — sp 2e00re

ad. rt : JEDOWNL Ra re ine ene SBOMNLET

SALT pe a LE S geome

Figure 3-6 JAMMA Filter PCB Schematic Diagram A047292-01 B

Page 29

suonensny] sued

d 10-267LF0V Penupuo) ‘wesSeig 2peUIEYIS qd Jey, WWW! 9-€ 2unS]y 30H On Eun © OH gu wi O— sy un oH Ht S

a0) @Z-UAKLIT CONS] 22-uhubr CAMO LET 9Z-UhlNsr C@MLAIID Sz-BHET CENOLLNE 42-chbr C2NOLINE) E2-wMHLr CTNOLINE I 2z-UHUUr CONDI] 12-bHKOr CATT) 02-UAHUT COTNHODS GT -ueAIr cen] @T-URMEIT CUUWWLS) JT-wuHUr N10] 97 -uAlur CAsaLs1as) St-uMuUr ONO G19 AT-BAT CaN) Ey-BHAEr coma) 2T-wanUr cong) TT-tMiisr Cs Taxd8 3 OT-BT CFya07-3) b- HHH CIMINGD 3 a~bAHOT AD c-bunur Caste) 9-eHNUr CAS-9 S-BHRUT CAGE 3 eB casey e-UHWr CONT] -2-UHUT ONO) T-UHHYr CAN] dd-BHE COND) 23-BHKUE CaaLHOLy) da-UAWOr eR 3-H CENOLLNERY Ba-WHAU C2NOL.LNGY 3. Ue“ CWO! 109 CuML HOLY cua CUUNNO > cuyund a-ehRUe CHLWLS >) N-UAHUT CINTOD L-aMUT CLIELD S-UMWUT c30raa3s) a-whr CONKS 2 d-UAWGr NTaNQ]N-UHUIT cao anya H-BhHUr C-TYWdS 3 -UHWE CYNOOT-33-BHRUE Seer O-bubet D-UMtsr B-wHUr B-Hultsr SSBNUUH

oa ano Oa ano os ar Lar oO a aL O-——» BTINMOr Oe tune oe re oan lar ou Oe BINNIE Os atone o——s Tiawise mma NTOSTE Oo = 1S Lsr ——s ONSITAr Oe amar os aur sonter wTidase Oo by00TF oa VULNS oO oa neter ose Oa AGH oa ncer O-—9 GNI o——= ano Aner oa ana, o——« ano, oa aziar oe azar (O--—» GeNHOOr O-—-a Beane oe 1ytsr oa zur os vane Cm BANHOOE m= uzane 24yuLse Nroour mature oe nase On ONS Ome NETUON oa anaaniue oe ase oe eon one BULNIT Oo Oe nate Ome nse Oa ner awso OL 4M fessoarug Aled Poa

Page 30

Parts Illustrations World Rally Universal Kit

OPF & & = Fy

= E & s

Figure 3-7 JAMMA Filter PCB Assembly A047292-01 B

JAMMA Filter PCB Assembly Parts List

natorDescriptionPart No.natorDescriptionPart No.
c1-82200 pF, SOV, 3-Pin EMI Filter Cap.140006-222C32, C33270 pF, SOV, 3-Pin EMI Filter Cap.140006-271
C9,C10270 pF, SOV, 3-Pin EMI Filter Cap.140006-27134-462200 pF, 50V, 3-Pin EMI Filter Cap.140006-222
C11-312200 pF, 50V, 3-Pin EMI Filter Cap.140006-222jiConnector, 56 Ckt., .156 Ctr, RT179240-056

3-10

Page 31

i sn co pe ee is mt nd noi shipment. None of the Seller's other products or parts thereof are warranted. Ep the roduc: Gescribed iia) thie enaral falls lconfortaleo te wateanre Seller's sole liability shall be, at its option, to repair, replace, or credit Buyeee which are returned to Seller during said war- Tanty

(a) Seller is promptly notified in writing upon discovery by Buyer that

said products are defective; (b) Such products are returned prepaid to Seller's plant; and (© Seller's examination of said discloses to Seller’s satisfaction

that such alleged defects and were not caused by accident,

In no event shall Seller be liable for loss of profits, loss of use, incidental or consequential damages.

warranties a lar purpose, and of all other obligations or liabilities on the Seller’s part, and it neither assumes nor authorizes any other person to assume for the Seller any other liabilities in connection with the sale of products by

warranty. The use of any non-Atari parts may also adversely affect the safety of your game and cause injury to you and others. Be very cautious in using non-Atari-supplied components with our games, in order to ensure your safety.

Corporation part or any modification including labor which is performed by such distributor.

Page 32

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.