CATHODE RAY TOMES

Toobin TM-320 1st Printing

Toobin' (rev 3) (Atari Games, 1988) · Technical Manual · 64 pages · 60 sections · original scan

Page 1

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 2

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 3

ATARI

AMES o

Toobin’: Operators Manual with Illustrated Parts Lists

Page 4

© 1988 by Atari Games Corporation. All rights reserved.

No part of this publication may be reproduced by any mechanical, photographic or electronic process, or in the form of a phonographic recording, nor may it be stored in a retrieval system, transmitted, or otherwise copied for public or private use, without permission from the publisher. The game play, all graphic designs, this technical manual, its accompanying schematic diagrams, and the display manual are protected by the U.S. Copyright Act of 1976. This Act provides for substantial penalties for violating federal copyright laws. Courts can impound infringing articles while legal action is pending. If infringers are convicted, courts can order destruction of the infringing articles. In addition, the Act provides for payment of statutory damages of up to $50,000 per infringing transaction in certain cases. Infringers may also have to pay costs and attorneys’ fees and face an imprisonment of up to five years as well as fines of up to $250,000 in the case of individuals and up to $500,000 in the case of corporations. Atari Games Corporation will aggressively enforce its copyrights against infringers. We will use all legal means to immediately halt any manufacture, distribution, or operation of a copy of video games made by us. Anyone who purchases such copies risks forfeiting such a game.

Published by: Atari Games Corporation 675 Sycamore Drive P.O. Box 361110 Milpitas, California 95035

Printed in the U.S.A 6S

Produced by the Atari Games Technical Publications Department Toobin’

Page 5

Toobin’

Notice Regarding Non-Atarie Parts

WARNING Use of non-Atari pasts or modifications of any Atari game circuitry may adversely affect the safety of your game, and may cause injury to you and your players.

You may void the game warranty (printed on the inside back cover of this manual) if you do any of the following: © Substitute non-Atari parts in the game. ° Modify or alter any circuits in the game by using kits or parts not supplied by Atari Games Corporation.

NOTE

This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instruction manual, may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of Federal Communications Commission (FCC) Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area or modification to this equipment is likely to cause interference, in which case the user, at his own expense, will be required to take whatever measures may be required to correct the interference. If you suspect interference from an Atari game at your location, check the following:

  • All ground wires in the game are properly connected as shown in the game wiring diagram. © The power cord is properly plugged into a grounded three wire outlet. © On games provided with an Electromagnetic Interference (EMI) ground plane, be sure the game printed-circuit boards (PCBs) are properly installed on the EMI Ground Plane. If you are still unable to solve the interference problem, please contact Customer Service at Atari Games Corporation. See the inside front cover of this manual for service in your area.

iii

Page 6

Table of Contents

Set-Up How to Use This Manual. Inspecting the Game..... Control and Switch Locations. Setting the Coin and Game Options. Game Play... Maximizing Earnings.. Self-Test RAM/ROM Tes\ Control Test. Alphanumeric Test. Coin Options Game Options Statistics Histograms. Playfield Scroll Test Motion Object Test. Color Test... Color Purity Test Convergence Test Intensity Test Sound Test... Maintenance Preventive Maintenance Preventive-Maintenance Interval: Maintaining the Attraction Drum Cleaning the Coin Mechanism... Cleaning the Interior Components. Corrective Maintenance. Removing the Video Display.. Replacing the Video Display Removing the Game PCB.... Replacing Static-Sensitive Devices Replacing Snap-Action Switches Removing the Fluorescent Lights Removing the Speaker..... Replacing the Attraction Drum Motor Illustrated Parts Lists Toobin’ Statistics Glossary Warranty Toobin’

Page 7

Toobin’

List of Illustrations

Figure 1-1

Figure 2-1 Figure 2-2 Figure 2-3 Figure 2-4 Figure 2-5 Figure 2-6 Figure 2-7 Figure 2-8 Figure 2-9 Figure 2-10 Figure 2-11 Figure 2-12 Figure 2-13 Figure 2-14 Figure 2-15

Figure 3-1 Figure 3-2 Figure 3-3

Figure 4-1 Figure 4-2 Figure 4-3 Figure 4-4 Figure 4-5 Figure 4-6 Figure 4-7

Table 1-1

Table 2-1 Table 2-2 Table 2-3 Table 2-4 Table 2-5

Table 3-1 Control and Switch Locations

Failing RAM Test .. 2-2 Failing ROM Test 2-2 Control Test..... 2-2 Alphanumeric Test. 2-3, Coin Option: 2-3 Game Options. Statistics Screen. Histograms ...... Playfield Scroll Test Motion Object Test Color Test Color Purity Te: Convergence Test .. Intensity Test..... Sound Test Screen

Lubricating the Attraction Drum Control Panel, Video Display, and Speaker Removal. Replacing Snap-Action Switches

Cabinet-Mounted Assemblies .. Contro] Panel Assembly .. Attraction Drum Assembly . Switching/Linear (SL) Power Supply Assembly Coin Acceptors, Inc. Coin Door Assembly. Toobin’ Game PCB Assembly .... Stand-Alone Audio PCB Assembly.

List of Tables

Game Specifications

Faulty RAM Locations... Faulty ROM Locations . Coin Options .. Game Options Faulty Sound RAM and ROM Locations.

Recommended Preventive-Maintenance Intervals

Page 8

Safety Summary

The following safety precautions apply to all game operators and service personnel. Specific warnings and cautions will be found in this manual whenever they apply.

WARNING Properly Ground the Game. Players may receive an electrical shock if this game is not properly grounded! To avoid electrical shock, do not plug in the game until it has been inspected and properly grounded. This game should be only be plugged into a grounded three-wire outlet. If you have only a two-wire outlet, we recommend you hire a licensed electrician to install a three-wire grounded outlet. If the control panel is not properly grounded, players may receive an electrical shock! After servicing any part on the control panel, check that the grounding wire is firmly secured to the inside of the control panel. After you have checked this, lock up the game. AC Power Connection. Before you plug in the game, be sure that the game’s power supply can accept the AC line voltage in your location. The line voltage requirements are listed in the first chapter of this manual. Disconnect Power During Repairs. To avoid electrical shock, disconnect the game from the AC power before removing or repairing any part of the game. If you remove or repair the video display, be very careful to avoid electrical shock. High voltages continue to exist even after power is disconnected in the display circuitry and the cathode-ray tube (CRT). Do not touch the internal parts of the display with your hands or with metal objects! Always discharge the high voltage from the CRT before servicing it. Do this after you disconnect it from the power source, First, attach one end of a large, well-insulated, 18-gauge jumper wire to ground, Then momentarily touch the free end of the grounded jumper wire to the CRT anode by sliding the wire under the anode cap. Wait two minutes and do this again. Use Only Atari Parts. To maintain the safety of your Atari game, use only Atari parts when you repair it. Using non-Atari parts or modifying the game circuitry may be dangerous, and could injure you and your players. Handle the CRT With Care. If you drop the CRT and it breaks, it may implode! Shattered glass from the implosion can fly six feet or more. Use the Proper Fuses. To avoid electrical shock, use replacement fuses which are specified in the parts list for this game. Replacement fuses must match those replaced in fuse type, voltage rating, and current rating. In addition, the fuse cover must be in place during game operation.
CAUTION Properly Attach All Connectors. Make sure that the connectors on each printed circuit board (PCB) are properly plugged in. The connectors are keyed to fit only one way. if they do not slip on easily, do not force them, If you reverse a connector, it may damage your game and void your warranty. Ensure the Proper AC Line Frequency. Video games manufactured for operation on 60 Hz line power (used in the United States) must not be operated in countries with 50 Hz line power (used in Europe). If a 60 Hz machine operates on 50 Hz line power, the fluorescent line ballast transformer will overheat and cause a potential fire hazard. Check the product identification label on your machine for the line frequency required. ABOUT NOTES, CAUTIONS, AND WARNINGS In Atari publications, notes, cautions and warnings have the following meaning:
NOTE—A highlighted piece of information.
CAUTION—Equipment and/or parts can be damaged or destroyed if instructions are not followed. You will void the warranty on Atari printed-circuit boards, parts thereon, and video displays if equipment Or parts are damaged or destroyed due to failure of following instructions.
WARNING—Players and/or technicians can be killed or injured if instructions are not followed. Toobin’
Page 9

Chapter 1

Set-Up

How to Use

This Manual

This manuai is written for game operators and service personnel, and provides information for setting up, playing, testing, and maintaining your Toobin’™ game. The manual is divided into the following chapters: ¢ Chapter 1 contains set-up and game play information.

  • Chapter 2 contains selftest procedures.
  • Chapter 3 contains preventive and corrective maintenance procedures.
  • Chapter 4 contains illustrated part lists. Wiring and schematic diagrams for the Toobin’ game circuitry are contained in the Schematic Package Supplement (SP-320) included with your game. This chapter includes information required to set up and piay your Toobin’ game. Carefully read the information in this chapter before applying power.
Page 10

Set-Up

WARNING To avoid electrical shock, do not plug in the cabinet until it has been properly inspected and set up for the line voltage in your area. This cabinet should be connected to a grounded three-wire outlet only. If you have only a twowire outlet, we recommend that you hire a licensed electrician to install a grounded outlet. Players can receive an electrical shock if the cabinet is not properly grounded.

Inspecting the Game

WARNING Do not plug in the game until you have completed the following inspection steps.

Please inspect your Toobin’ game carefully to ensure that the game is complete and was delivered to you in good condition. Figure 5-1 shows the locations of the component parts of the game. Table 1-1 lists space, power, and environmental requirements. Inspect the factory-assembled game as follows: 1, Examine the exterior of the cabinet for dents, chips, or broken parts.

  • Unlock and open the rear access panel. Unlock and open the coin doors. Inspect the interior of the cabinet as follows: a. Ensure that all plug-in connectors (on the cabinet harnesses) are firmly plugged in. Do not force connectors together. The connectors are keyed so they fit only in the proper orientation. A reversed edge connector can damage a printed-circuit board (PCB) and will void your warranty.

Table 1-1 Game Specifications

Characteristic Specification

Power Consumption 150 V-A, 110 W RMS Temperature +5° to +50° C (437° to +122° F) Humidity Not to exceed 95% relative Line Voltage 102 to 132 VAC (U.S. games) Width 25.25 in. (64 cm) Depth 34.75 in. (88 cm) Height 72 in. (183 cm) Weight 270 Ibs. (123 kg)

1-2 Toobin’

b. Ensure that all plug-in integrated circuits on each PCB are firmly plugged into their sockets. c. Inspect the power cord for any cuts or dents in the insulation. d, Inspect the power supply. Make sure that the correct fuses are installed. Check that the harness is plugged in correctly and that the fuse block cover is mounted in place. Check that the green ground wires are connected. e. Inspect other major sub-assemblies, such as the video display, printed-circuit boards (PCBs), and speaker. Make sure that they are mounted securely and that the ground wires are connected.

Control and Switch

Locations

Power On/Off Switch The power on/off switch is located at the bottom rear of the cabinet. (See Figure 4-1.) Volume Control The volume control is located on the Audio PCB behind the upper coin door. (See Figure 1-1.) The volume control adjusts the level of sound produced by the game.

Self-Test Switch The self-test switch is located on the corner of the Audio PCB behind the upper coin door. (See Figure 1-1.) The self-test switch selects the Self-Test Mode to check game operation. Refer to Chapter 2 for a complete description of self-test operation. Coin Counter The coin counter is located on the shelf inside the upper coin door. The coin counter records the number of coins deposited.

Setting the Coin and Game Options

The Toobin’ coin and game options are set in the Self- Test Mode. Refer to Chapter 2 for the recommended settings and the procedure for setting the options.

Game Play

This part of the manual describes the theme and game play of the Toobin’ game.

Page 11

Toobin’

Coin Door

i Auxiliary Coin Switch Set-Up

Stand-Alone Audio PCB

Volume Control

Self-Test Switch

Coin Counter

Figure 1-1 Control and Switch Locations Introduction Toobin’ is a unique fantasy-adventure game. One or two players can race Bif and Jet, the Toobin’ dudes, in their inner tubes, down 45 different rivers. The players try to keep Jet and Bif afloat, avoiding sharp objects, gaining points, and throwing cans at obstacles. Toobin’ appeals to both males and females of all ages who both find it just “fun to play.” Toobin’ has a continuous buy-in feature so players can join in at any time. Toobin’ has a color-coded control panel and players can identify Jet in the yellow inner tube and Bif in the black inner tube and red shorts. Each player has a set of four buttons to steer Bif or Jet forwards, backwards, and sideways. Pressing the two Paddle Forward buttons moves the inner tube forward. Pressing the two Back Paddle buttons moves the inner tube backwards. Pressing only one Paddle button makes the inner tube turn. The player uses the Throw Can button to destroy obstacles in the river and stun riverside pests. Toobin’ players can enjoy amusing game play and an incredible variety of rivers and environments for their long-term enjoyment

Play Mode

The player races Bif or Jet against other players, or against the game, down Toobin’s 45 different rivers, paddling through six classes of play, and cruising the 15 unique river environments. The player can choose almost 200 courses through the rivers, finding his own way through rapids, obstacles, riverside pests and waterfalls. The player has to guide Bif or Jet around obstacles, go through gates and pick up treasure to accumulate points to get more inner tube patches, collect cans to throw at obstacles and to stun riverside pests, and paddle fast enough to avoid the big gator lurking in all the rivers. At the finish line, players are treated to a party. Each party grows in size until the player reaches the final super party at the end of the game. Inner-Tube Patches: At the beginning of each game, the player has a certain number of inner-tube patches, which represent game lives. A player receives extra patches by scoring the number of points required for another patch. The number of points required changes from level to level, and is displayed in the lower left and right corners of the playfield. A player can also receive more patches by picking up patches floating in the rivers. Points: The player can score points by:

  • Time of Travel: The player receives points simply for traveling down the river. ° Passing through Gates: The player receives points for passing through the gates in the river. Differentcolored gates are worth different amounts of points. The green gates give the lowest points, then the red, gold, and finally crystal gates give the highest points. If a players “swishes” a gate, that is, paddles through it without hitting the poles, he adds to his Score Multiplier. (This is described in Score Multiplier below.) For maximum points, the player should be the first through the gate and swish the gate. Each time the gate poles are hit, the point value of the gate falls.
  • Score Multiplier: If a player “swishes” the gate, the score is multiplied. Each gate that is swished adds to the multiplier. For example, if the player has a “2X” multiplier, each point scored is multiplied by 2. Every point the player scores is multiplied by the score multiplier. The score multiplier is shown in the upper left and right of the playfield, underneath the game scores. The minimum multiplier is 1 and the maximum is 5. The player must pass through every gate (whether he swishes it or not) to maintain the score multiplier. If

1-3

Page 12

set-up

the player misses a gate, the score multiplier is reduced by one. As long as the player passes through the gate, even if he bumps it, the score multiplier is maintained. However, if a player's tube is punctured, his score multiplier falls to one.

  • Treasures: The player can pick up treasures floating on the river or hidden under obstacles to gain extra points. The lowest-value treasure is green, next is red, and gold is the highest.
  • Warp: The warp feature moves the player to the intermediate or advanced play classes. When the player warps, he is rewarded with warp bonus points. Warping is a good way to quickly score points. Cans: The player must accumulate cans to throw at obstacles and pests. All cans are the same value. The player can pick up individual cans floating in all the rivers or six-packs hidden under obstacles or in back waters. (Six packs give unlimited cans.) The player throws the cans by pointing Bif or Jet at the obstacle and pressing the Throw Can button. Most of the obstacles in the river can be eliminated by hitting them with a can. Dangers: The player must avoid or eliminate dangers in the river and stun pests on the river banks. The dangers in the river include: ° Falling rocks * Floating logs
  • Deadly falling coconuts * Icebergs ¢ Mines ¢ Stampeding cattle © Snakes * Crocodiles © Barbed wire * Thorny bushes Dangerous riverside pests throw and shoot objects at Bif and Jet. The player can stun most of these objectionable characters with a can thrown in their direction. These pests include:
*Casting fishermen.° — Hillbillies
¢Terrorists*Devils
*¢Martians*Street punks
©Pistolaros*Natives
¢=Penguins°Bears
*Dinosaurs*Cavemen

Big ’Gator : If a player is slow, the big ‘gator comes up from behind to discourage slow play and hurry the player through the gates. A loud thumping sound warns the player of its presence. One escape from the big ‘gator is to quickly paddle downstream or pass through a gate. If the gator catches Bif or Jet, one inner-tube patch is lost.

Maximizing Earnings

Operator options on this game have been kept very simple. You should thoroughly read Chapter 2, Self- Test, for information on the Coin Options, Game Options, Histogram, and Statistics screens so that you can Toobin’

effectively use the available options. Use the Self-Test screens showing Statistics and Histogram to evaluate game data, and the Game Options screen to make adjustments. (Refer also to the Self-Test chapter for more information on setting options.) The key to maximum earnings is striking a midpoint on game times. Game times must be short enough so that player turnover is high. Conversely, game times must be long enough to give players a good value and ensure repeat play. (Repeat play is crucial to longevity.) The Toobin’ software gives the operator the flexibility to tune game difficulty and enough statistics to intelligently make adjustments. If collections seem low or are dropping off, check all player controls and coin mechanisms for proper operation. If earnings seem low, the game is technically sound, and the average game time per quarter is under 150 seconds, try changing the game-difficulty option to an easier setting. This change will give players more game time for their money. If the average game time per quarter is over 270 seconds, first try changing the game difficulty to a harder setting. If the average game time per quarter is still over 270 seconds after a few weeks, try an even harder setting. After changing the game-difficulty settings, it is a good idea to reset the game statistics and the histograms. The game statistics can be cleared in the self-test by pressing all the Back Paddle buttons simultaneously. The histograms can be cleared by pressing all the Back Paddle buttons simultaneously while you are on the seventh histogram screen.

Special Contest Feature Every Toobin’ game in the U.S has a special contest. A player can win a free Toobin’ t-shirt just for playing the game and finding and picking up all seven characters to spell the word Toobin’ (including the apostrophe). These characters are hidden in the river below obstacles and hazards. The letters collected by the player are shown at the beach party at the end of the run. For more contest details, see the game.

Page 13

Chapter 2

Self-Test

The Toobin™ game tests itself and provides visual and audible indications of the condition of the game circuitry and controls, Self-test information is displayed on the screen and through the sound system. No additional equipment is required. We suggest that you perform a self-test when you first set up the game, each time you collect the money, or when you suspect game failure.

The self-test screens provide information about the game circuits and controls. The game enters the self-test mode after the self-test switch is turned on. The following selftest screens are arranged in the sequence in which they occur when the self-test switch is turned on. After the sound test, the sequence starts over with the control test. If you turn off the self-test switch at any time during the selftest mode, the game returns to the attract mode.

The self-test switch is located on the front corner of the Stand- Alone Audio board, inside the coin door.

Page 14

Self-Test

RAM/ROM Test The RAM/ROM Test screens are shown in Figures 2-1 and 2-2. If the game has errors in the RAM, ROM, or associated circuitry, this test provides information about the location of the error. If the RAMs and ROMs pass the test, the self-test advances to the Control Test. The RAM/ROM Test is divided into two sections. The RAM Test is performed first. If the RAM Test passes after a six-second delay, the self-test skips to the ROM Test without displaying any message. If the RAM fails, a message is displayed on the screen as shown in Figure 2-1. See Table 2-1 for informtion about RAM problems.

Figure 2-1 Failing RAM Test If no errors occur, the ROM Test displays no messages and advances to the Switch Test. If a ROM fails, a message is displayed as shown in Figure 2-2. Refer to Table 2-2 for the location of the failing ROM. If you get a message on the screen, press the left player Start button to advance to the Switch Test.

Table 2-1 Faulty RAM Locations

RAM Type Location Video Display Characteristic

CPU7), 7FBackground color is red.

PF 1E, 3E, 4/SE Background color is green.

AL/MO.17D, 18DBackground color is blue.
COL8),Background color varies be-

tween red, white, and blue.

2-2 Toobin’

Table 2-2 Faulty ROM Locations

Error Address Location on Game PCB

00000U=lL=1F
20000U=JL=2F
40000u=4L=4F
60000u=5)L=5F

Figure 2-2 Failing ROM Test

Control Test

The control test is shown in Figure 2-3. Use this test to check the condition of the buttons. As you press each button, the corresponding position on the screen turns red if it is operating correctly. Press both Start buttons to go to the next test.

CONTROL TEST

Figure 2-3 Control Test

Page 15

Toobin’

Alphanumeric Test

The alphanumeric test checks the condition of the alphanumerics in the game. The screen is shown in Figure 2-4, If you see an error on the screen, check the EPROM at 20H. Press the left Start button to go to the next test.

Figure 2-4 Alphanumeric Test

Coin Options

Check and select the coin options on this screen. The screen is shown in Figure 2-5. The coin option setting defaults are shown in green. The coin option that you are changing is shown in a blue box. Press the left player Back Paddle buttons to move up and down the screen. Change any of the option settings by pressing either left player Paddle Forward button. Exit the screen by pressing the left Start button. To save your changes, you must press the left Start button before you leave the Self-Test. Change all the option settings back to the factory defaults by pressing the furthest right Paddle Forward button. To return to your original option settings, press the right Start button, The coin options are as follows: Coin Mode has a blue box around it when the screen first appears. The blue box means that you can change this option. The coin mode settings you can choose are:

  • One coin equals one credit (default)
  • Two coins equal one credit Self-Test

Figure 2-5 Coin Options

  • Three coins equal one credit
  • Four coins equal one credit Right Mech Multiplier is the next option. Move to this option by pressing the right Paddle Forward button for the left player. Change the setting of this option when it has a blue box around it. The settings you can choose are:
  • One coin counts as one coin (default)
  • — Six coins count as one coin
  • Five coins count as one coin ¢ Four coins count as one coin

Left Mech Multiplier is the next option. Move to this option by pressing a Paddle Forward button for the

Table 2-3 Coin Option Settings Coin Mode One coin equals one credit # Two coins equal one credit Three coins equal one credit Four coins equal one credit One coin counts as one coin # Six coins count as one coin Five coins count as one coin Four coins count as one coin Right Mech Muttiplier

Left Mech Multiplier One coin counts as one coin +

One coin counts as two coins

No bonus adder # 2 coins give 1 extra coin 4 coins give 1 extra coin 4 coins give 2 extra coins 5 coins give 1 extra coin 3 coins give 1 extra coin Free Play (for demonstration mode) + Manufacturer's recommended settings Bonus Adder

Page 16

Self-Test

left player. Change the setting on this option when it has a blue box around it. You can choose these settings:

  • One coin counts as one coin (default)
  • One coin counts as two coins Bonus Adder is the next option. To move to this option, press down either Paddle Forward button on the left player side. Change the setting on this option when it has a blue box around it. You can choose these settings:
  • No bonus adder (default) 2 coins give 1 extra coin 4 coins give 1 extra coin 4 coins give 2 extra coins 5 coins give 1 extra coin 3 coins give 1 extra coin Free play (for demonstration mode) eoeeeee

To go to the game options screen, press the left Start button.

Game Options

Use this screen to check and select the game options. The screen is shown in Figure 2-6. The game option setting defaults are shown in green. You can change the setting when the option has a blue box around it. Press the left player Back Paddle buttons to move up or down the option list. Change any option setting by pressing either left player Paddle Forward button. Exit the screen by pressing the left Start button. To save your changes you must press the left Start button before leaving the Self-Test. Change the options to the factory defaults by pressing the furthest right Paddle Forward button. To return to your original option settings, press the right Start button. The game option settings are as follows. Difficulty Level has a blue box around it when the screen first appears. Choose the player difficulty level. The levels are:

  • Easiest Easier Easy Medium (default) Medium Hard Hard Harder Hardest eee eecee Toobin’

Clear High Score Table is the next option. Move to this option by pressing the left player's right Paddle Forward button. Use this option to clear the high score table displayed in the attract mode. ° Yes ° No (default)

Figure 2-6 Game Options Demo/Play Mode is the next option. Move to this option by pressing the left player's right Paddle Forward button. Use this option to choose the play mode or the demonstration mode.

  • Playable Game Mode (default)
  • Demonstration Only Mode Starting Lives is the number of times a player's inner tube can be punctured before sinking. The settings are: 7 2
  • 3 (default) 2° 4

Music in Attract Mode turns the music on or off in the attraction mode. ° Yes (default) ° No Special Cost allows you to choose either 2 credits to start and 1 to continue, or the standard coin setting.

  • 2 credits to start, 1 to continue (default) ° None
Page 17

Toobin’

Table 2-4 Game Option Settings Option Name Settings

Difficulty Setting Easiest Easier

Easy Medium +

Medium Hard Hard

Harder Hardest

Clear HighYesNo +

Score Table

Demo Play Mode Playable Game Mode + Demonstration Only Mode

Starting Lives23+

4 5

Music in Attract ModeYes #No

Special Cost 2 credits to start, 1 to continue None Contest Enabled (default for U.S. games)* Disabled (default for European games) + Manufacturer's recommended settings

Contest is the last game option. For U.S. games, the default is that the contest is enabled, but for European games, the default is disabled. The contest is briefly described at the end of Chapter 1. ¢ Enabled (default for U.S. games) ¢ Disabled (default for European games) Exit the screen by pressing the left Start button.

Statistics

Use the statistics shown on this screen and on the histogram screens to track your game use. Record the statistics on the Toobin’ statistics sheet found in the back of this manual. The statistics screen is shown in Figure 2-7, The information on the screen is accumulated from the last time the statistics were reset. Also on this screen is the date the program was created. If you call Atari Games Customer Service with a problem, you may need this information. To reset the statistics screen, simultaneously press all of the Back Paddle buttons. Exit the screen by pressing the left Start button. The statistics screen shows the following information: ° Left Coins shows the number of coins deposited in the left coin mechanism. Self-Test

Figure 2-7 Statistics Screen Right Coins shows the number of coins deposited in the right coin mechanism. New Games shows the number of new games started. Continuation shows the number of games continued. O Plyr Mins shows the number of minutes the game had no players. I Plyr Mins shows the number of minutes the game was played by one player. 2 Plyr Mins shows the number of minutes the game was played by two players. New Mins shows the number of minutes the game was played as a new game. Cont Mins shows the number of minutes the game was played as a continued game. Sessions shows the number of sessions played. A session starts when the first coin is put in and ends when the last player leaves the game. Error Count shows the number of errors counted in the erasable memory. This should have a count of less than 75 per week. If it has more, then the game should be repaired. Total Coins shows the number of coins deposited. Avg Time/Coin shows the average number of seconds per coin. Avg Time/New Game shows the average number of seconds per new game. (This calculates the average time correctly whether or not you are using the 2 coins to start, 1 coin to continue setting.)

Page 18

Self-Test

« Aug Time/Cont Game shows the average number of seconds per continued game. (This calculates the average time correctly whether or not you are using the 2 coins to start, 1 coin to continue setting.)

Histograms

This game has seven histogram (horizontal bar graph) screens. The first one is shown in Figure 2-8. The histogram information is accumulated from the last time the screens were cleared. You can clear all the histogram screens by pressing all the Back Paddle buttons at the same time when you are in the seventh histogram screen. To move through the screens, press the left Start button.

Figure 2-8 Histograms The seven histogram screens show the following: New easy games in seconds New medium games in seconds New hard games in seconds Easy continuation games in seconds Medium continuation games in seconds Hard continuation games in seconds Sessions in minutes

Playfield Scroll Test

You can test the playfield scrolling circuitry in this screen. Use the left player buttons to move left, right, up, and down. The screen is shown in Figure 2-9. eoeeeee

Exit the screen by pressing the left Start button.

2-6 Toobin’

Figure 2-9 Playfield Scroll Test

Motion Object Test

The motion object test screen is shown in Figure 2-10. This tests the movement and color of various game objects.

Figure 2-10 Motion Object Test Use the left player paddle buttons to move the objects left, right, up and down. The left player Start button is the Exit button as usual.

Page 19

Toobin’

Use the right player buttons to do the following: ¢ Press the left Back Paddle button to flip the object vertically.

  • Press the right Back Paddle button to flip the object horizontally. © Press the left Paddle Forward button to change the picture in the object.
  • Press the right Paddle Forward button to change the coior of the object. ¢ Press the Start button to choose the next object.

Color Test

This test indicates the condition of the video display color circuits. The scfeen is shown in Figure 2-11. The screen changes from white at the bottom to black in the middle. The last black line in the middle should be definitely black. Above the black line, red, green, and blue become darker and darker, with the colors and the black border blending into each other at the top of the screen. If the screen does not fit this description, see the video display manual included with the game for adjustments. Exit the screen by pressing the left Start button.

Figure 2-11 Color Test

Color Purity Test

The color purity test has five screens. The first screen is shown in Figure 2-12. These screens show the condition of the color purity circuit in the video display. Each screen should display a rectangle of color, with no curving at the corners and no lines in the display. The screens are red, green, Self-Test

Figure 2-12 Color Purity Test blue, white and gray. If the screens are not correct, see the video display manual included with the game for adjustments. Exit each screen by pressing the left Start button.

Convergence Test

The convergence test is shown in Figure 2-13. This test has three screens. The first is white, the second is purple, and the last is green. Check the following on the screens: ¢ The grid lines should be straight within 3.0 mm and the lines should not pincushion or barrel.

  • The convergence of the lines on the violet and white screens should be within 2.0 mm.

Figure 2-13 Convergence Test

2-7

Page 20

Self-Test

If these screens do not meet these criteria, see the video display manual for suggested adjustments. Exit the screen by pressing the left Start button.

Intensity Test

This test checks the intensity circuit and the interrupt circuit of the video display. The screen is shown in Figure 2-14. You should see a number of grey vertical bars from light to dark across the display. If these bars do not appear, there is problem in either the intensity or the interrupt circuit. You can determine which circuit is the problem by going into the play mode. If the screen does not fade out when the the game goes into play mode, then something is wrong with the intensity circuit. If the game does not display anything at ali, then something is wrong with the interrupt circuit. Exit the screen by pressing the left Start button. Toobin’

Sound Test

The sound test indicates the condition of the music and sound effects circuits. The sound test screen is shown in Figure 2-15. The sound microprocessor resets at the beginning of the test. You will hear the first sound three seconds after the test starts.

Figure 2-15 Sound Test Screen.

After the microprocessor is reset and you hear the first sound, the number of game sounds and the sound CPU status information appear. If the CPU is good, the word “Good” appears. The test cycles through the following tests: © Music Chip Test

  • Effects Chip Test ¢ SCOM Reset Test
Page 21

Toobin’ Self-Test

Table 2-5 Faulty Sound RAM and ROM Locations Error Message Location on Cause or Comment Stand-Alone Audio PCB Music Chip Time Out 2F Sound CPU Interrupt Error 2F, 5K, Transistor Q8 Sound CPU RAM 1 Error 2H Sound CPU ROM 1 Error 2K If displayed when entering test, then sound processor cannot run further. Press the Left Player Start button to go to the next test. Communications Error #1 1M ‘Will count number of errors caused by either the Stand-Alone Audio PCB or Game PCB. This error message usually means that the SCOM chip (part no. 137526-001) on one of these boards is bad.

CAUTION The SCOM chip is a CMOS IC and is static sensitive. IF you do not handle it properly, you can permanently damage this chip. See the section Replacing Static-Sensitive Devices, in Chapter 3 of this manual, for more information.

Communications Error #2 A probable disconnection of the Stand-Alone Audio PCB from the Game PCB, or the chip at 1M is not inserted into its socket. Sound Processor Not A major problem with the Stand-Alone Audio PCB. If you cannot enter the Responding self-test, the cause may be a harness disconnection between the Stand- Alone Audio Board and the Game PCB.

After these tests, the 4th Music Chip Test begins. Use the buttons on the control panel to select sounds in the test and listen to them. Use the player buttons to do the following: ¢ Press the left player Back Paddle buttons to move forward and back through the sound list. Press the left player left Paddle Forward button to stop the sound. Press the right player Start button to play the sound. Press the left player Start button to exit the sound test. You return to the first test in the self-test series.

Page 22

Self-Test

N

2-10 Toobin’

S

Page 23

Chapter 3

tenance

This chapter includes preventive and corrective maintenance \. procedures for the Toobin’™ game components that are subject to the most use. To assure maximum troublefree operation from this game, we recommend that preventive maintenance be performed as described in this chapter. Removal, disassembly, re-assembly, and replacement procedures are provided for components that might require corrective maintenance. Appropriate references are provided to Chapter 4, Illustrated Parts Lists, to help locate the parts of this game that are mentioned, but not illustrated, in the maintenance procedures.

Page 24

Maintenance Toobin’

Preventive Maintenance

Preventive maintenance includes cleaning, lubricating, and tightening hardware. How often preventive maintenance is performed depends upon the game environment and frequency of play. However, for those components listed in Table 3-1, Recommended Preventive-Maintenance Intervals, we recommend that preventive maintenance be performed at the intervals specified.

WARNING To avoid possible electrical shock, turn off the game before performing any maintenance procedures.

Preventive-Maintenance Intervals

The preventive-maintenance intervals specified in Table 3-1 are the recommended minimum requirements for the components listed.

Table 3-1 Recommended Preventive- Maintenance Intervals Attraction Drum _Lubricate and tighten hardware at least every three months. Coin Mechanism _ Inspect whenever you collect coins. Clean at least every three months.

Maintaining the Attraction

Drum

Preventive maintenance on the attract drum consists of:

  • Lubricating the five points shown in Figure 3-2.
  • Tightening the screws on the left side of the frame that hold the drum shafts in place.

Lubricating the Attraction Drum

  • Remove the two screws on the top of the game cabinet that secure the retainer. Take off the retainer.
  • Remove the inner and outer attraction shields and attraction graphics.
  • Lightly oil the plastic bearings that hold the drum shafts in the frame. Do this at each of the five locations shown on Figure 3-1.

3-2

Tightening the Attraction Drum

1, Tighten the hex-head screws that hold the attraction drums in place. You will not be able to reach all of the screws, but tighten the ones you can reach.

  • Tighten the screws that hold the frame to the cabinet and that hold the light fixture on the frame.
  • If you take out the frame to replace the motor or the light fixture, tighten all the nuts at that time.
  • When you are done, replace the retainer and tighten the two screws that hold the retainer on the cabinet. Cleaning the Coin Mechanism Use a soft-bristled brush to remove loose dust or foreign material from the coin mechanism. A toothbrush can be used to remove any stubborn build-up of residue in the coin path. After cleaning the coin mechanism, blow out all of the dust with compressed air. Cleaning the Interior Components
WARNING Turn off the game power, but do not unplug the power cord before cleaning inside the cabinet. The power cord provides a ground path for stray static voltages that can be present on the cleaning tools.

Perform the following procedure to clean the components inside the cabinet.

  • Unlock and open the rear access panel and display service panel.
  • Discharge the high voltage from the cathode-ray tube (CRT) before proceeding. The display assembly contains a circuit for discharging the high voltage to ground when power is removed. However, to make certain, always discharge the display as follows: a. Attach one end of a large, well-insulated, 18gauge jumper wire to ground. b. Momentarily touch the free end of the grounded jumper to the CRT anode by sliding it under the anode cap.
Page 25

Maintenance Toobin’

Fluorescent Lamp

Gear Motor

Figure 3-1 Lubricating the Attraction Drum

c. Wait two minutes and repeat part b. 3. Use a vacuum cleaner with a soft long-bristled brush attachment or use a soft-bristled paint brush

CAUTION to remove loose dirt and dust accumulated on the inside of the cabinet. Be sure to clean the electrical components thoroughly (power supplies, PCB assemblies, display, etc.). Be extremely careful when cleaning the electrical components inside the cabinet. Avoid touching the electrical components with any solid object other than the soft bristles of the vacuum attachment or paint brush.
Page 26

Maintenance Toobin’

Corrective Maintenance

Corrective maintenance consists of removal, disassembly, re-assembly, and replacement of game components, The following procedures are provided for components that may require corrective maintenance.

Removing the Video Display

Replacing the Video Display

Perform the following procedure to remove/replace the video display. (See Figure 3-2.)

  • Turn the game power off and wait two minutes. Unplug the power cord.

‘WARNING High Voltage The video display contains lethal high voltages. To avoid injury, do not attempt to service this display until you observe all precautions necessary for working on high-voltage equipment. X-Radiation The video display has been designed to minimize X-radiation. However, to avoid possible exposure to soft X-radiation, never modify the high-voltage circuitry. Implosion Hazard The cathode-ray tube may implode if struck or dropped. Shattered glass may cause injury within a 6-foot radius. Use care when handling the display.

  • Open the coin door. Reach up through the coin door to the control panel and unlatch the latches on both sides of the it. Tilt the control panel up and disconnect the harness connectors. Remove the control panel.
  • Use the finger hole below the video display to help you remove the video display shield. 4, Carefully remove the bezel from the protective foam tape.
  • Open the rear access panel.
  • Be sure that the game power is turned off before discharging the high voltage from the cathode-ray tube (CRT). The display assembly contains a circuit for discharging the high voltage to ground when power is removed. However, to make certain, always discharge the display as follows:

3-4 a. Attach one end of a large, well-insulated, 18gauge jumper wire to ground. b. Momentarily touch the free end of the grounded jumper to the CRT anode by sliding it under the anode cap. c. Wait two minutes and repeat part b. ~ . From the rear of the cabinet, disconnect the display harness connectors from the display.

  • Remove the two wood cleats on the left and right sides of the cabinet. Use a Phillips screwdriver to remove the 2 screws on each side.
  • Use a 3/8-inch nut driver to remove the four hex head-washer bolts holding the display onto the metal mounting brackets in the cabinet.
  • Carefully lift the display out through the front of the cabinet.
WARNING To avoid dropping the video display, use extreme care when removing the display from the cabinet. We recommend that no one weighing less than 150 pounds should attempt to remove the display. In addition, we recommend that you wear gloves to protect your hands from the sheet-metal edges.
  • Replace the video display as described in the following procedure.

Perform the following procedure to replace the video display in the cabinet. (See Figure 3-2.)

NOTE Whenever the cathode-ray tube and yoke are replaced as a single unit, readjust the brightness, size, and centering as described in the display manual. Also check the purity and convergence according to the display manual instructions, but adjust both only if required.
Page 27

Display Shield Toobin’ Maintenance

Inner Attraction Shield Video Display Outer Attraction Shield

4/2-Inch Foam Tape Display Bezel

Control Panel Assy

Draw Latch Attraction Graphics

Bezel Support ‘Wood Cleat 1/4-inch Foam Tape Retainer ‘Speaker | Speaker Grille Attraction Drum Assy

Rear Door

Display Mounting Bracket

Figure 3-2 Control Panel, Video Display, and Speaker Removal

  • Carefully lift the video display through the front of the cabinet.
  • Position the display so that the four holes in the video display mounting brackets align with the four holes in the top and bottom metal bracket.
  • Install the four hex head-washer bolts through the display frame and mounting brackets. 4, Use a 3/8-inch nut driver to tighten the bolts. Be sure that the display is centered horizontally.
  • Connect the display harnesses to the display.
  • Install the two cleats that support the bezel and the display shield.
  • Replace the bezel and display shield.

Removing the Game PCB

Perform the following procedure to remove or replace the Toobin’ Game PCB.

  • Turn the game power off.
  • Unlock and remove the rear access panel from the cabinet.
  • Disconnect the harness connectors from the Game PCB.
  • Use a Phillips screwdriver to remove the two screws and washers holding the Game PCB to the cabinet. we . Grasp the edge of the Game PCB and gently lift it out of the slotted guide.
  • Replace the Game PCB in the reverse order of removal.
Page 28

Maintenance

Replacing Static-Sensitive

Devices

Be careful when you are working with static-sensitive devices, such as microprocessors, field-effect transistors (FET), complementary metal-oxide semiconductors (CMOS), and other large-scale integration (LSI) devices that use metal-oxide semiconductor (MOS) technology. Static charge that has built up in your body can cause a static-sensitive device to fail. Leakage from an improperly grounded soldering iron can also cause a static-sensitive device to fail. Before you handle a static-sensitive device or a PCB with such devices attached to it, ground any static voltage that may have accumulated in your body by touching an object that has been earth grounded. A bare wire wrapped around your wrist and attached to an earth ground is effective when working extensively with static-sensitive devices. When you solder a static-sensitive device, use a solder-

Yellow Button Assy

Control Panel

Snap Action Switch Toobin’

ing iron with a properly grounded three-wire cord. Before you replace a static-sensitive device, make sure it is actually defective. A static-sensitive device can appear defective due to leakage on a PCB. To make sure a device is defective, ground static voltages as described in the paragraph above. Clean both sides of the PCB with flux remover or an eraser. For discrete FETs, clean thoroughly between the gate, drain, and source leads. Then test the device. New static-sensitive devices can be packaged in conductive foam or can have a protective shorting wire attached to the pins. Remove the conductive foam just prior to inserting the device into its socket or soldering it to a PCB. Remove the shorting wire only after the device is inserted into its socket or after all the leads are soldered in place.

Replacing Snap-Action

Switches

Perform the following procedure to replace any of the snap-action switches. (See Figure 3-3.)

Red Button Assy

Figure 3-3 Replacing Snap-Action Switches

3-6

Page 29

Toobin’

1, Open the coin door. . Reach up through the coin door to the contro] panel. Unlatch the latches on both sides of the control panel that hold it in place. nN

ww . Disconnect the control panel harness connector and remove the control panel from the cabinet. 4, Remove the two connectors on the switch. . Remove the switch by twisting and pulling the switch to release it from the plastic pegs in the bottom of the button assembly.

  • Push a new switch into the holder. Make sure the pegs on the button assembly go into the two holes in the side of the switch. . Push the electrical connectors onto the switch. wu

N

  • Replace the control panel in the cabinet.

Removing the Fluorescent Lights

Perform the following procedure to remove or replace the fluorescent lights. (See Figure 3-3.)

  • Turn the game power off.
  • Remove the two screws holding the retainer on the top of the cabinet. Remove the retainer.
  • Remove the attraction shields and attraction graphics. 4, Remove the fluorescent light from the light fixture.
  • To remove the entire light fixture, take out the attract drum frame. Remove the four screws in the top and bottom that hold the frame on the cabinet.
  • Disconnect the motor and light connectors from the cabinet harness. Take out the attract drum frame.
  • Unscrew the two screws that hold the light fixture on the frame. Take the wire out of the tie wrap on the side. Remove the light fixture.
  • Replace the light fixture and put new tie wraps around the wires on the side. Maintenance
  • Replace the attract drum frame in the cabinet.
  • Replace the attraction shields with the attraction graphics between them. Replace the retainer.

Removing the Speaker

Perform the following procedure to remove the speaker. (See Figure 3-2.)

  • Turn the game power off.
  • Remove the four screws holding the speaker grille to the cabinet. Remove the grille.
CAUTION Do not touch the speaker cone when handling the speaker. The cone material is fragile and can be easily damaged.
  • Use a Phillips screwdriver to remove the four screws holding the speaker to the cabinet. Do not let the speaker fall.
  • Lower the speaker just far enough to disconnect the two speaker wires.
CAUTION Do not rest the speaker against the video display. The magnet in the speaker will cause color impurity. You may have to re-adjust the video display if you put the speaker on the screen.

wu . Replace the speaker in the reverse order of removal. Be sure that you hook up the wires correctly. The signal wire on the speaker should be attached to the speaker tab marked with color, a “+” sign, or a round dot. (The signal wire is shown on the game wiring diagram; refer to the Schematic Package included with the game.)

Page 30

Maintenance

Replacing the Attraction

Drum Motor

Perform the following procedure to replace the attraction drum motor. (See Figure 3-2.)

  • Turn the game power off.
  • Remove the two screws that secure the retainer on the top of the cabinet. Remove the retainer.
  • Remove the attraction shields and attraction graphics,

4, Remove the four screws on the top and bottom that hold the frame in the cabinet. 10.

11. Vindicators

Disconnect the motor and light connectors from the cabinet harness. Take out the attraction drum frame. Take the wire out of the tie wrap on the side.

Loosen the set screw that holds the drum onto the motor shaft.

Using a 1/4-inch Allen wrench, remove the hex head nuts that hold the motor onto the frame.

Replace the motor, and replace the hex-head nuts. Tighten the set screw that holds the drum onto the motor shaft. Put new tie wraps around the wires on the side.

Replace the attraction drum frame.

Page 31

Chapter 4

Illustrated

Parts Lists

This chapter provides information you need to order parts for your game. Common hardware parts, such as screws, nuts, washers, and so on are not in the parts lists. The PCB parts lists are arranged in alphabetical order by component, Each component section is arranged alphanumerically by reference designator. Other parts lists are arranged alphanumerically by Atari part number. In these parts lists, all A-prefix numbers come first. Next come part numbers with a two-number designation followed by a hyphen (00- through 99-). Ending the list are part numbers with six numbers followed by a hyphen (000598- through 201000-). When you order parts, give the part number, part name, the number of this manual, and the serial number of your game. With this information, we can fill your order rapidly and correctly. We hope this will create less downtime and more profit from your game. Atari Customer Service phone numbers are listed on the

inside front cover of this manual.

Page 32

Illustrated Parts Lists

045546-01 Inner Attraction Shield

045511-01 148007-104 Attraction Graphics Speaker 045935.01 045515-01 043276-04 Outer Attraction Shield ‘Speaker Grille Retainer

04551301 Display Bezel

178056-002 1/2-Inch Foam Tape Toobin’

A045933-01 \ Attraction Drum Assy i | i

045514-01 Display Shield /

176027-4416 Screw with Washer

139012-304 Video Display

037332-01 Grille

045512-01 Display Mounting Bracket,

045516-02 y . Large Right Decal A045508-01 NJ Control Panel Assy 178013-001 786900402 Draw Latch 1/4-inch Foam Tape (2 piaces) 045536-01

Rear Door 045510-02 Front Decal 045516-04

‘Small Right Decal

A043713-24 SA Audio PCB Assy

/ 178120-606 171027001 Coin Door PCB Standoff

171078-002 038091-01 Coin Counter Coin Box

Figure 4-1 Cabinet Mounted Assemblies A045504-01 B

4-2

Page 33

Toobin’ Illustrated Parts Lists

Not Shown

A043909-02 +5 Volt Harness Assy

(A045549-01 Speaker Harness Assy

(A045571-01 Cabinet Hamess Assy

A045572.01 Power Hamess Assy

A045573-01 ‘AC Power Harness Assy

A045574-01 Video Hamess Assy

A045576-01 Com./Aud. Harness Assy 045516-01 A045577-01 Large Left Decal Ground Strap Assy

178129-001 Wire Routing Clip

034536-02 Foam Vibration Damper

045516-03 ‘Small Left Decal

A043055-01 On/Off Harness Assy SS RAB AREIDO

404405821 Game PCB Assy

Adjustable Glide Koasianes 178093-01 Power Supply Assy Fan Blade Guard

Figure 4-1 Cabinet-Mounted Assemblies, Continued

Page 34

Illustrated Parts Lists Toobin’

Cabinet-Mounted Assemblies Parts List

Part No. Description

A043055-01 On/Off Harness Assembly A043713-24 Stand-Alone Audio PCB Assembly (see Figure 4-7) A043909-02 +5 Volt Harness Assembly A044058-21 ‘Toobin’ Game PCB Assembly (see Figure 4-6)

A045140-01 SL Power Supply Assembly (see Figure 4-4) A045508-01 Control Panel Assembly (see Figure 4-2) A045549-01 Speaker Harness Assembly A045571-01 Cabinet Harness Assembly

A045572-01 Power Harness Assembly A045573-01 AC Power Harness Assembly A045574-01 Video Harness Assembly A045576-01 Com./Aud. Harness Assembly

A045577-01 Ground Strap Assembly A045933-01 Attraction Drum Assembly (see Figure 4-3) 034536-02 Foam Vibration Damper 037332-01 Louvered Grille

038091-01 Molded Coin Box 043276-04 Retainer 045511-01 Attraction Graphics 045512-01 Display Mounting Bracket

045513-01 Display Bezel 045514-01 Display Shield 045515-01 Speaker Grille 045516-01 Upper Left Side Decal

045516-02 Upper Right Side Decal 045516-03 Left Decal Next to Control Panel 045516-04 Right Decal Next to Control Panel 045510-02 Front Decal

045935-01 Attraction Shield 045536-01 Rear Door 045546-01 ‘Textured Inner Attraction Shield 045548-01 Light Reflector

139012-304 Wells-Gardner 19-inch Medium Resolution Video Display 148007-104 4 1/2-inch Round Shielded Speaker 171027-001 Over/Under 25¢/25¢ USA Coin Door (see Figure 4-5) 171078-002 Non-Resettable 12V DC Coin Counter 175008-002 #10 White Nylon Washer 176019-220 #8 Cross Recessed Screw 176027-4016 #10 Hex Head Screw with Washer 176027-4416 1/4 Hex Head Screw with Washer

178013-001 Draw Latch 178056-002 1/2-inch Wide, 4-inch Long Foam Tape 178093-01 Fan Blade Guard 178120-606 PCB Standoff

178129-001 Wire Routing Clip 78-3201 Adjustable Glide

4-4

Page 35

Toobin’ Illustrated Parts Lists

Cabinet-Mounted Assemblies Parts List, Continued

Part No. Description

78-6900402 1/4-inch Wide, 40-inch Long Foam Tape

These items are the technical information supplements to the game: Toobin’ Schematic Package Toobin’ Self-Test Label Toobin’ Operators Manual Weils-Gardner (Model #197635) 19-inch Color Video Display Service Manual

Page 36

Ittustrated Parts Lists ‘Toobin’

Not Shown A045575-01 045509-01 Control Harness Assy Contro! Panel 045510-01 Control Panel Decal

178237-001 Red Button Assy

<

178237-002 Yellow Button Assy a

160044-001 Snap Action Switch

Figure 4-2 Control Panel Assembly A045508-01 A

Control Panel Assembly Parts List

Descrption

A045575-01 Control Hamess Assembly 045509-01 Control Panel 045510-01 Control Panel Decal 160044-001 Snap-Action Switch

178237-001 Red Button Assembly 178237-002 Yellow Button Assembly

4-6

Page 37

Toobin’ Illustrated Parts Lists

178232-002 Lamp Retaining Clip 170003-003 Fluorescent Lamp

171086-003 Lamp Fixture

145004-001 Gear Motor

170003-003 Fluorescent Lamp 178232-002 Lamp Retaining Clip

‘A045550-01 171086-003 AC Splitter Harness Lamp Fixture Assy

Attraction Drum Assembly Parts List

Part No. Description

A045550-01 AC Splitter Harness Assembly 107013-001 Light Oi] Lubricant 145004-001 120 VAC, 16 RPM, CW Gear Motor 170003-003 8W 12-inch Long Fluorescent Lamp 171086-003 118V, 60Hz, 12-inch Long Electrical Lamp Fixture (Acceptable substitute is part no, 171086-004) 178232-002 Lamp Retaining Clip

Page 38

Illustrated Parts Lists Toobin’

A WARNING A The switching power supply has high voltages on it when power is turned on Therefore, ne sure you do not touch this power supply unless you have turned off the power to the game.

149003-003 T2-HAA606S 5V 10A Switching Screw Power Supply Assy a 179231-002 ¢ AOSSET IK Terminal Block 4 442047-001 meet t | Transformer

A043367-XX + Jumper Assy a 72-HA4B06S A043909-02 Screw SV Harness Assy

049996-01 Power Supply Chassis Base

A042384-01 Line Filter Assy

146007-3002 3-Amp Fuse

Warning Lable!

179225-2205, or 79-3206 Fuse Block 034544-01 Fuse Block Cover

043622-01 Fuse Label 14607-2002 2-Amp Fuse

Figure 4-4 Switching/Linear (SL) Power Supply Assembly A045140-01 A

4-8

Page 39

Toobin’

Switching/Linear Power Supply Assembly Illustrated Parts Lists

Parts List

Part No. Description

A042384-01 Line Filter Assembly A043367-01 Jumper Assembly A043367-02 6-Inch Black Jumper Assembly A043367-03 6-Inch White Jumper Assembly 72-HA4606s #6-32 Thread-Forming Screw 72-HA4806s #8-32 Thread-Forming Screw 034544-01 Fuse Block Cover 037640-01 Power Supply Warning Label

043396-01 Power Supply Base Chassis 043622-01 Power Supply Fuse Label 142047-001 Power Transformer 146007-2022 2-Amp 250 V 3AG Slow Blow Fuse 146007-3022 3-Amp 250 V 3AG Slow Blow Fuse 149003-003 Hitron 5V 10A Switching Power Supply (see below) 179225-2205 5-Position Fuse Block (Acceptable substitute is part no. 79-3206) 179231-002 2-Position Terminal Block

Hitron 5-Volt Power Supply Sub-Assembly Model HSA-122B(S) Parts List

DesignatorDescriptionPart No.

Capacitors

clCapacitor, Metal Film, 0.047 pF, 250 V99-211036
c2Capacitor, Metal Film, 0.1 pF, 400 V99-211038
C3, C4Capacitor, Ceramic, 4700 pF, 400 V99-211049
C5, C6Capacitor, Electrolytic, 100 pF, 200 V99-211046
C7Capacitor, Metal Film, 0.1 pF, 400 V99-211038
csCapacitor, Ceramic, 0.001 pF, 2 kV99-211042
coCapacitor, Ceramic, 0.01 pF, 1 kV, Z5U99-211041
10Capacitor, Electrolytic, 220 pF, 25 V99-211045
cllCapacitor, Metal Film, 0.22 F, 100 V99-211037
C12Capacitor, Metal Film, 0.022 pF, 100 V99-211039
C13Capacitor, Metal Film, 0.22 F, 100 V99-211037
C14Capacitor, Ceramic, 1800 PF, 2 kV, Z5 V99-211040
C17Capacitor, Electrolytic, 470 pF, 25 V99-211044
cloCapacitor, Electrolytic, 2200 pF, 16 V99-211048
C20Capacitor, Electrolytic, 1000 uF, 25 V99-211047
C21Capacitor, Ceramic, 470 PF, 1 kV, Z5P99-211043
C22Capacitor, Electrolytic, 2200 pF, 16 V99-211048
C23Capacitor, Electrolytic, 1000 pF, 25 V99-211047
C24Capacitor, Electrolytic, 2200 pF, 16 V99-211048

Diodes

D1, D2Diode, Fast Recovery, RPG10K99-211010
D3Diode, Fast Recovery, RPG15B99-211011
D4Diode, Fast Recovery, RPG10B99-211009
DS5-D7Diode, Switching, 1N414899-211012
Page 40

Ihustrated Parts Lists

Hitron 5-Volt Power Supply Sub-Assembly Model HSA-122B(S) Parts List, Continued ‘Toobin’

DesignatorDescriptionPart No.
D9Diode, Fast Recovery, 30DF199-211006
D1, D12Diode, Schottky, $10SC4M99-211005
D13.-D16Diode, Rectifier, 1N400699-211008

Inductors

11Inductor, 15 mH99-211052
13Inductor, 7 pH (Acceptable substitute is part no. 99-211051),99-211050
14Inductor, 2.2 pH99-211054
15Inductor, 1.5 mH99-211053

Resistors

R1, R2Resistor, Carbon Film, 180 K Ohm, +5%, 1 W99-211034
R3.Resistor, Wirewound, 120 Ohm, +5%, 2 W99-211019
R4Resistor, Wirewound, 0.47 Ohm, +5%, 2 W99-211018
RSResistor, Wirewound, 33 Ohm, 5%, 2 W99-211917
RO, R7Resistor, Carbon Film, 5.6 Ohm, 25%, 1/4 W99-211027
RSResistor, Wirewound, 0.47 Ohm, 5%, 2 W99-211018
ROResistor, Carbon Film, 10 Ohm, +5%, 1/4 W99-211029
R10Resistor, Carbon Film, 1 K Ohm, +5%, 1/4 W99-211032
R11Resistor, Carbon Film, 47 Ohm, +5%, 1/4 W99-211025
R12Resistor, Carbon Film, 5.6 Ohm, +5%, 1/4 W99-211027
R13Resistor, Carbon Film, 330 Ohm, +5%, 1/4 W99-211026
R14Resistor, Carbon Film, 270 Ohm, +5%, 1/2 W99-211023
R15Resistor, Carbon Film, 330 Ohm, +5%, 1/2 W99-211022
R16Resistor, Carbon Film, 8.2 Ohm, +5%, 1/4 W99-211028
R17, R18Resistor, Carbon Film, 56 Ohm, +5%, 1/4 W99-211031
RIDResistor, Carbon Film, 39 Ohm, +5%, 1/4 W99-211030
R20Resistor, Carbon Film, 2 K Ohm, +5%, 1/4 W99-211035
R21Resistor, Carbon Film, 470 Ohm, +5%, 1/4 W99-211024
R22Resistor, 2.2 K Ohm, +2%, 1/4 W99-211021
R23Resistor, Metal Film, 2K Ohm, +2%, 1/4 W99-211033
R25Resistor, Carbon Film, 10 Ohm, +5%, 1/4 W99-211029
R26Resistor, Wirewound, 50 Ohm, +5%, 2 W99-211015
R27Resistor, Carbon Film, 47 Ohm, #5%, 1/4 W99-211025
R31Resistor, Wirewound, 150 Ohm, +5%, 2 W99-211016

Transistors

aTransistor, NPN, 2SC1413A99-211002
Q3Transistor, NPN, PE8050B99-211003
Q3Transistor, PNP, PE8550B99-211004

Miscellaneous

FlFuse, 2 A, 250 V, SEMKO99-211058
Ic1Regulator, UA431AWC99-211001
SCR1Thyristor, SCR99-211013,
TlTransformer99-211055
TRIThermistor, 0.5 Ohm, +5%, 5 W99-211020
VRIPotentiometer, Trimming, 3 K Ohm99-211014
ZD1Diode, Zener, 1N752A99-211007

Fuse, 2 A, 250 V 99-211056 Fuse Holder, 6.35 mm. 99-211060 Terminal Block, 8 Ckt 99-211057 Heat Sink 99-211059 Heat Sink, 1.5 mm. 99-241061

4-10

Page 41

Toobin’ Hlustrated Parts Lists

ON O T E S

+ heen

Page 42

IMlustrated Parts Lists Toobin’

99-10140 Panel Assembly

75-948S Lecknut 99-10116 Lever

99-10152 Right Coin Inlet 99-10147 Harness

171006-035 Coin Mechanism

75-944 S Locknut

99-10096 Fastener 99-10151 \ Left Coin Inlet ®-

7011-47 Lamp

99-10080 Lamp Socket

99-10105 72-9406S os

Screw

aA

99-10104 Bar Retainer

99-10042 thru 99-10045 a Coin Switch Assembly 99-10154 Bracket Assembly

99-10153 Coin Return Box 99-10150 ae ‘Switch Cover

99-1068 Coin Chute .

65-4416 . Coin Switeh ,

99-10075 thru 99-10078 4

‘Switch Wires

99-10008 Retainer 75-1412S Screw

Figure 4-5 Coin Acceptors, Inc. Coin Door Assembly 171027-001 A

4-12 EE ————aooo————— ST - ——_ hy

Page 43

Toobin’ Illustrated Parts Lists

99-10148 Lock Assembly

99-10160 Coin Inlet Housing

72-HA1404C (7 Screw

g a 99-10161 K 4 |~—— Side Entry Button Assy 99-10139 Coin Door A

'S ‘Spring 99-10148 Lock Assembly

99-10147 Coin Return Cover

99-10117 Coin Return Door

72-JA1405B A \a— 9010144 Screw Z Channel Clip

> 99-15068 Screw

| 99-10149 a y - Service Door

038091-01 eon : ' :

Coin Box Nee :

: ? 99-10143 Frame

NOTE

The acceptable substitute for this door (and the one used in games manufactured in Ireland) is the Coin Controls Ltd. Coin Door Assembly, part number 171034-001. You can obtain a free Coin Controls Ltd. i supplement (part. no, CO-305-01) that has illustrations and a parts list. Write to Atari Games Ireland Limited, Tipperary Town, Ireland, Telephone 062-52155.

Figure 4-5 Coin Acceptors, Inc. Coin Door Assembly, Continued

Page 44

Illustrated Parts Lists Toobin’

Coin Acceptors, Inc. Coin Door Assembly Parts List

Part No. Description

65-441C Coin Switch 70-11-47 Miniature Bayonet Lamp 72-9406S #4-40 x 3/8-Inch Truss-Head Screw 72-HA1404C #4-40 x 1/4-Inch Pan-Head Screw 72-JA1405B #4-40 x .31-Inch Pan-Head Screw 75-1412S #4-40 x 3/4-Inch Pan-Head Screw 75-9948 #4-40 Locknut 99-10008 Retainer 99-10042 Coin Switch Assembly for Belgian 5 Fr and U.S. 25¢

99-10043 Coin Switch Assembly for German 1 DM, Japanese 100 Yen, Swiss 1 Fr

99-10044 Coin Switch Assembly for German 2 DM, Italian 100 L, U.S. $1.00 99-10045 Coin Switch Assembly for Australian $.20, German 5 DM, British 10 P 99-10068 Coin Return Chute 99-10075, Switch Wire (included in coin switch assembly 99-10043) 99-10076 Switch Wire (included in coin switch assembly 99-10042) 99-10077 Switch Wire (included in coin switch assembly 99-10044) 99-10078 Switch Wire (included in coin switch assembly 99-10045) 99-10080 Lamp Socket 99-10081 Key Holder 99-10096 Fastener 99-10104 Bar Retainer 99-10105 Bar 99-10115 Spring 99-10116 Plastic Coin Return Lever

99-10117 Steel Coin Return Door 99-10139 Coin Door 99-10140 Coin Door Inner-Panel Assembly 99-10141 Die-Cast Coin Return Cover

99-10143 Coin Door Frame 99-10144 Channel Clip 99-10147 Harness 99-10148 Lock Assembly

99-10149 Service Door 99-10150 Switch Cover 99-10151 Left Coin Inlet 99-10152 Right Coin Inlet 99-10153 Coin Return Box 99-10154 Bracket Assembly 99-10160 1-Inch Wide Die-Cast Coin Inlet Housing

99-10161 25¢ Amber Side-Entry Coin Button Assembly

99-15066 Screw for Clamp 171006-035 Metal Coin Mechanism for U.S. 25¢

4-14

Page 45

‘Toobin’ Illustrated Parts Lists

_ Meee

Bo oO

Figure 4-6 Toobin’ Game PCB Assembly A044058-01 C

4-15

Page 46

Illustrated Parts Lists Toobin’

Toobin’ Game PCB Assembly Parts List

DesignatorDescriptionPart No.

Integrated Circuits

1AIntegrated Circuit, EPROM, 27512-200136061-1101
1BIntegrated Circuit, EPROM, 27512-200136061-1105
1cIntegrated Circuit, 741824437-7418244
1DIntegrated Circuit, 74L$8637-T4LS86
1EIntegrated Circuit, RAM, 8Kx8, 100 nsec137535-004
1FIntegrated Circuit, EPROM, 27512-300136061-1137
yyIntegrated Circuit, EPROM, 27512-300136061-1133
1MIntegrated Circuit, 740637-7406
2AIntegrated Circuit, EPROM, 27512-2006136061-1102
2BIntegrated Circuit, EPROM, 27512-200136061-1106
2cIntegrated Circuit, 74LS37337-7418373
2DIntegrated Circuit, 74115737-741S157
2FIntegrated Circuit, EPROM, 27512-300136061-1138
2JIntegrated Circuit, EPROM, 27512-300136061-1134
2/KIntegrated Circuit, 74HC273137556-001
2KIntegrated Circuit, 7415260137332-001
3CIntegrated Circuit, 74F374137420-001
3DIntegrated Circuit, 74LS15737-74LS157
3E, 4/SEIntegrated Circuit, RAM, 8Kx8, 100 nsec137535-004
4AIntegrated Circuit, EPROM, 27512-200136061-1103
4BIntegrated Circuit, EPROM, 27512-200136061-1107
4cIntegrated Circuit, 74F374137420-001
4DIntegrated Circuit, 74115737-741S157
4FIntegrated Circuit, EPROM, 27512-300136061-1139
4yIntegrated Circuit, EPROM, 27512-300136061-1135
4KIntegrated Circuit, 74LS260137332-001
5AIntegrated Circuit, EPROM, 27512-200136061-1104
5BIntegrated Circuit, EPROM, 27512-200136061-1108
5cIntegraied Circuit, 74LS37337-7418373
5DIntegrated Circuit, 74LS15737-741S157
SFIntegrated Circuit, EPROM, 27512-300136061-1140
5JIntegrated Circuit, EPROM, 27512-300136061-1136
SVKIntegrated Circuit, 74HC273137556-001
5KIntegrated Circuit, 741$17437-741S174
6cIntegrated Circuit, 741824437-7418244
6D, 6EIntegrated Circuit, 741817437-74LS174
6MIntegrated Circuit, 74LS15737-74L8157
7BIntegrated Circuit, SOS137550-001
7C, 7DIntegrated Circuit, 74F219137567-001
JEIntegrated Circuit, PAL, 16L8 A136061-1151
7K, 7}Integrated Circuit, RAM, 8Kx8, 150 nsec137441-001
7L, 7MIntegrated Circuit, 74L$138137177-001
8BIntegrated Circuit, SOS137550-001
8CIntegrated Circuit, 74F219137567-001
Page 47

Toobin’ Ilustrated Parts Lists

Toobin’ Game PCB Assembly Parts List

DesignatorDescriptionPart No.
8D, 8EIntegrated Circuit, 74F374137420-001
8FIntegrated Circuit, 74F174137531-001
8HIntegrated Circuit, 74LS245,37-74L8245
3Integrated Circuit, RAM, 2Kx8, 45 nsec137534-002
8KIntegrated Circuit, 2804 A-45, 450 nsec137329-450
8LIntegrated Circuit, 74189037-741890
8MIntegrated Circuit, 7480237-74L802
9cIntegrated Circuit, 74L$17437-7418174
9E, OFIntegrated Circuit, 74F153137492-001
9HIntegrated Circuit, 741524537-7418245
9Integrated Circuit, RAM, 2Kx8, 45 nsec137534-002
9K, 9LIntegrated Circuit, 741824537-7ALS245
9MIntegrated Circuit, 74LS163 A37-74L8163A
10AIntegrated Circuit, 1M Bit, Mask ROM, LH231000136061-1143,
10BIntegrated Circuit, 1M Bit, Mask ROM, LH231000136061-1147
10CIntegrated Circuit, 741S163 A37-74LS163A
10DIntegrated Circuit, 74F163137345-001
10E, 10F, 10HIntegrated Circuit, 74F153137492-001
10KIntegrated Circuit, 741813937-TAL8139
10MIntegrated Circuit, 741824437-7418244
11¢, 11DIntegrated Circuit, 74LS163 A37-74L8163A
IEIntegrated Circuit, 74F21137555-001
11FIntegrated Circuit, 74F163137345-001
11HIntegrated Circuit, 74F398137557-001
lyIntegrated Circuit, 741824437-7418244
11KIntegrated Circuit, 74LS0037-74LS00
11MIntegrated Circuit, 74L$24437-7418244
12C, 12DIntegrated Circuit, 7415163 A37-T4LS163A,
12E, 12FIntegrated Circuit, 74F163137345-001
124gIntegrated Circuit, 74F08137483-001
12KIntegrated Circuit, 74182037-74LS20
12MIntegrated Circuit, 741813937-74L8139
13AIntegrated Circuit, 1M Bit, Mask ROM, LH231000136061-1144
13BIntegrated Circuit, 1M Bit, Mask ROM, LH231000136061-1148
13C, 13DIntegrated Circuit, 741$17437-7418174
13E, 13FIntegrated Circuit, 74F163137345-001
13KIntegrated Circuit, 74183237-74L832
13LIntegrated Circuit, 68010137414-002
13MIntegrated Circuit, 74180037-TALS00
14CIntegrated Circuit, 74F00137327-001
14DIntegrated Circuit, 7418158137203-001
14EIntegrated Circuit, 74F283137506-001
14FIntegrated Circuit, 741517437-74L8174
14HIntegrated Circuit, 74F163137345-001
14KIntegrated Circuit, 74181437-74LS14
14MIntegrated Circuit, 74LS7437-741874
Page 48

Illustrated Parts Lists Toobin’

Toobin’ Game PCB Assembly Parts List

DesignatorDescriptionPart No.
15CIntegrated Circuit, 74180437-74LS04
15DIntegrated Circuit, 7418158137203-001
15EIntegrated Circuit, 74F283137506-001
15FIntegrated Circuit, 741837437-74LS374
15HIntegrated Circuit, 74F244137502-001
15JIntegrated Circuit, 74F174137531-001
15KIntegrated Circuit, 74183237-74L832
15MIntegrated Circuit, 74187437-74LS74
16AIntegrated Circuit, 1M Bit, Mask ROM, LH231000136061-1145
16BIntegrated Circuit, 1M Bit, Mask ROM, LH231000136061-1149
16CIntegrated Circuit, 74180437-74L804
16DIntegrated Circuit, 74L$158137203-001
16EIntegrated Circuit, 74F283137506-001
16FIntegrated Circuit, 741937437-7418374
16H, 16)Integrated Circuit, 74F164137568-001
16KIntegrated Circuit, 74153237-74LS32
17CIntegrated Circuit, 74F374137420-001
17DIntegrated Circuit, RAM, 8Kx8, 100 nsec137535-004
17FIntegrated Circuit, 741537437-74L8374
17H, 17JIntegrated Circuit, 741516437-7418164
17K, 17LIntegrated Circuit, 741S24537-7418245
18AIntegrated Circuit, 1M Bit, Mask ROM, LH231000136061-1146
18BIntegrated Circuit, 1M Bit, Mask ROM, LH231000136061-1150
18CIntegrated Circuit, 741837337-74L8373
18DIntegrated Circuit, RAM, 8KX8, 100 nsec137535-004
18FIntegrated Circuit, 741837337-741S373
18H, 18)Integrated Circuit, 7418194 A37-741S194
18K, 181, 19C, 19FIntegrated Circuit, 74LS24437-7418244
19H, 19)Integrated Circuit, 74L$15737-74LS157
19KIntegrated Circuit, SCOM137526-001
19LIntegrated Circuit, 741824437-741S244
20CIntegrated Circuit, 741827337-74LS273
20DIntegrated Circuit, 741S25737-74LS257
20EIntegrated Circuit, 74LS15337-741S153
20FIntegrated Circuit, 741827337-74L8273
20HIntegrated Circuit, EPROM, 27128-200136061-1142
20KIntegrated Circuit, 741$17437-74L8174
21AIntegrated Circuit, EPROM, 27512-200136061-1125
21BIntegrated Circuit, EPROM, 27512-200136061-1129
21CIntegrated Circuit, 741$27337-74L8273
21D, 21EIntegrated Circuit, 741517437-74LS174
21FIntegrated Circuit, 741527337-74LS273
21KIntegrated Circuit, 74188537-74LS85
22CIntegrated Circuit, 74L$27337-74LS273
22DIntegrated Circuit, 741915337-74LS153
22EIntegrated Circuit, 74L$283137204-001
Page 49

Toobin’ Ilusirated Parts Lists

Toobin’ Game PCB Assembly Parts List

DesignatorDescriptionPart No.
22FIntegrated Circuit, 741825737-74LS257
22HIntegrated Circuit, 74F163137345-001
225Integrated Circuit, 74F162137346-001
22KIntegrated Circuit, 7418163 A37-74LS163A
22L,Integrated Circuit, 74188537-74L885
23AIntegrated Circuit, EPROM, 27512-200136061-1126
23BIntegrated Circuit, EPROM, 27512-200136061-1130
23CIntegrated Circuit, 741517437-74LS174
23D, 23E, 23FIntegrated Circuit, 741S283137204-001
23HIntegrated Circuit, 7418163 A37-74LS163A,
23)Integrated Circuit, 74LS10937-T4LS109
23KIntegrated Circuit, 74F04137437-001
23LIntegrated Circuit, 74F08137483-001
24Integrated Circuit, EPROM, 27512-200136061-1127
24BIntegrated Circuit, EPROM, 27512-200136061-1131
24CIntegrated Circuit, 741517437-741S174
24DIntegrated Circuit, PROM, 828147136061-1152
24E, 24FIntegrated Circuit, 741S283137204-001
24HIntegrated Circuit, 74180437-741804
247Integrated Circuit, 74187437-74LS74
24KIntegrated Circuit, 74F74137436-001
241, 24L/MIntegrated Circuit, 74187437-74L874
254,Integrated Circuit, EPROM, 27512-200136061-1128
25BIntegrated Circuit, EPROM, 27512-200136061-1132
25C, 25D, 25EIntegrated Circuit, 74LS8637-741886
25FIntegrated Circuit, 741819337-74LS193
25HIntegrated Circuit, 74180837-74LS08
25)Integrated Circuit, 74F74137436-001
25KIntegrated Circuit, 74F32137486-001
251.Integrated Circuit, 74F10137428-001
2s1/MIntegrated Circuit, 74F00137327-001
26CIntegrated Circuit, 74LS0837-74LS08,
26DIntegrated Circuit, 741815737-74LS157
26EIntegrated Circuit, 74LS19137-74LS191
26FIntegrated Circuit, 74LS1037-74LS10
26H, 26)Integrated Circuit, 74F74137436-001
26KIntegrated Circuit, 74F139137488-001
26LIntegrated Circuit, 74F32137486-001
27Integrated Circuit, 741$138137177-001
27D, 27EIntegrated Circuit, 741$283137204-001
27FIntegrated Circuit, 74182037-74LS20
27LIntegrated Circuit, 74F112137569-001

EPROM Substitutes for Mask ROMS Substitute for Mask ROM at 10A

10AIntegrated Circuit, EPROM, 27512-200136061-1109
1AIntegrated Circuit, EPROM, 27512-200136061-1110

4-19

Page 50

Illustrated Parts Lists Toobin’

Toobin’ Game PCB Assembly Parts List

DesignatorDescriptionPart No.

Substitute for Mask ROM at 134

13AIntegrated Circuit, EPROM, 27512-200136061-1111
14AIntegrated Circuit, EPROM, 27512-200136061-1112

Substitute for Mask ROM at 16A

164Integrated Circuit, EPROM, 27512-200130061-1113
7AIntegrated Circuit, EPROM, 27512-200136061-1114

Substitute for Mask ROM at 184

18AIntegrated Circuit, EPROM, 27512-200136061-1115
20AIntegrated Circuit, EPROM, 27512-200136061-1116

Substitute for Mask ROM at 10B

10BIntegrated Circuit, EPROM, 27512-200136061-1117
11BIntegrated Circuit, EPROM, 27512-200136061-1118

Substitute for Mask ROM at 13B

13BIntegrated Circuit, EPROM, 27512-200136061-1119
14BIntegrated Circuit, EPROM, 27512-200136061-1120

Substitute for Mask ROM at 16B

16BIntegrated Circuit, EPROM, 27512-200136061-1121
7BIntegrated Circuit, EPROM, 27512-200136061-1122

Substitute for Mask ROM at 18B

18BIntegrated Circuit, EPROM, 27512-200136061-1123
20BIntegrated Circuit, EPROM, 27512-200136001-1124

Capacitors

C10-C26Capacitor, .1 pF, 50 V, Ceramic122002-104
C27-C30Capacitor, 100 pF, 100 V, Ceramic122016-101
C31Capacitor, .1 pF, 50 V, Ceramic122002-104
C32-C34Capacitor, 100 pF, 100 V, Ceramic122016-101
C35-C37Capacitor, .001 pF, 50 V, Ceramic122002-102
C38Capacitor, 33 pF, 50 V, Ceramic121015-330
€39-C41Capacitor, 100 pF, 100 V, Ceramic122016-101
C42Capacitor, 47 pF, 25 V, Electrolytic124009-476
C43,Capacitor, 68 pF, 100 V, Mica128002-680
C44Capacitor, 47 pF, 100 V, Mica128002-470
C45, C46Capacitor, .1 pF, 50 V, Ceramic122002-104
C47Capacitor, 47 pF, 25 V, Electrolytic124009-476
C48-C147Capacitor, .1 pF, 50 V, Ceramic122002-104

Inductor

LlInductor, 1 pH, 830 mA141007-001

Transistors

aTransistor, 2N5306133033-001
Q2-Q11Transistor, 2N390434-2N3904

Resistors

RIResistor, 1 K Ohm, +5%, 1/8 W110027-102
R2-RGResistor, 470 Ohm, +5%, 1/8 W110027-471
ROResistor, 1 K Ohm, +5%, 1/8 W110027-102
R18-R33Resistor, 470 Ohm, +5%, 1/8 W110027-471
R44-R59Resistor, 1 K Ohm, +5%, 1/8 W110027-192
ROOResistor, 100 K Ohm, +5%, 1/8 W110027-104
R61, R62Resistor, 1 K Ohm, +5%, 1/8 W110027-102
R63Resistor, 240 Ohm, +5%, 1/8 W110027-241
R64Resistor, 10 K Ohm, +5%, 1/8 W110027-103
Page 51

Toobin’ Illustrated Parts Lists

Toobin’ Game PCB Assembly Parts List

DesignatorDescriptionPart No.
R65Resistor, 4.7 K Ohm, +5%, 1/8 W110027-472
ROGResistor, 1 K Ohm, +5%, 1/8 W110027-102
RO7Resistor, 10 K Ohm, #5%, 1/8 W110027-103
R68-R71Resistor, 220 Ohm, #5%, 1/8 W110027-221
R72Resistor, 100 Ohm, +5%, 1/8 W110027-101
R73Resistor, 10 Ohm, +5%, 1/8 W110027-100
R74Resistor, 3.3 K Ohm, #5%, 1/8 W110027-332
RISResistor, 1 K Ohm, £5%, 1/8 W110027-102
R76Resistor, 300 Ohm, +5%, 1/8 W110027-301
R77Resistor, 2.4 K Ohm, #5%, 1/8 W110027-242
R78Resistor, 1 K Ohm, 25%, 1/8 W110027-102
R79Resistor, 100 Ohm, +5%, 1/8 W110027-101
R80Resistor, 10 Ohm, +5%, 1/8 W110027-100
R81Resistor, 3.3 K Ohm, +5%, 1/8 W110027-332
R82Resistor, 1 K Ohm, +5%, 1/8 W110027-102
R83Resistor, 300 Ohm, 25%, 1/8 W110027-301
R84Resisior, 2.4 K Ohm, +5%, 1/8 W110027-242
R85Resistor, 1 K Ohm, 25%, 1/8 W110027-102
R86Resistor, 100 Ohm, +5%, 1/8 W110027-101
R87Resistor, 10 Ohm, +5%, 1/8 W110027-100
R88Resistor, 3.3 K Ohm, +5%, 1/8 W110027-332
R89Resistor, 1 K Ohm, #5%, 1/8 W110027-102
R90Resistor, 300 Ohm, +5%, 1/8 W110027-301
ROLResistor, 2.4 K Ohm, +5%, 1/8 W110027-242
ROZResistor, 1 K Ohm, #5%, 1/8 W110027-102
R93-ROS.Resistor, SIP Network, 1K/2K Ohm, +2%118016-001
R96Resistor, 68, +5%, 1/8 W110027-680
ROTResistor, 10 K Ohm, 45%, 1/8 W110027-103
ROBResistor, SIP Network, 1K/2K Ohm, +2%118016-001
R99, R100Resistor, 1 K Ohm, +5%. 1/8 W110027-102
R101Resistor, 680 Ohm, +5%, 1/8 W110027-681
R102Resistor, 470 Ohm, 45%, 1/8 W110027-471
R103Resistor, 680 Ohm, +5%, 1/8 W110027-681
R104Resistor, 470 Ohm, #5%, 1/8 W110027-471
R105-R115,Resistor, 1 K Ohm, #5%, 1/8 W110027-102
R116Resistor, 470 Ohm, #5%, 1/8 W110027-471
R117Resistor, 680 Ohm, #5%, 1/8 W110027-681
R118Resistor, 1 K Ohm, +5%, 1/8 W110027-102
R119Resistor, 680 Ohm, 45%, 1/8 W110027-681
R120Resistor, 470 Ohm, +5%, 1/8 W110027-471
R121Resistor, 1 K Ohm, #5%, 1/8 W110027-102
R122, R123Resistor, 470 Ohm, +5%, 1/8 W110027-471
R124, R125Resistor, 680 Ohm, +5%, 1/8 W110027-681

4-21

Page 52

Illustrated Parts Lists Toobin’

Toobin’ Game PCB Assembly Parts List, Continued

Designator Description Part No.

Sockets Socket, 28 Pin, .600 179257-028 Socket, 24 Pin, .600 179257-024 Socket, 64 Pin, .900 179256-064 Socket, 20 Pin, .300 179259-020

Connectors

AUDConnector, 11 Ckt, Header, .100-Inch Ctr, Key 5179118-011
PWRConnector, 6 Ckt, Header, .250 Ctr179069-006
SWAConnector, 11 Ckt, Header, .100-Inch Ctr, Key 2179118-011
SWBConnector, 11 Ckt, Header, .100-Inch Ctr, Key 2179118-011
VIDConnector, 11 Ckt, Header, .100-Inch Ctr, Key 3179118-011

Miscellaneous

XlCrystal, 32.000 MHz144000-010
CRIDiode, MV5053, Light Emitting38-MV5053

Test Point 179051-001

4-22

Page 53

Toobin’

SRR e- Peg mean

i

  • Le Rta,

cos SP

Ry or

Page 54

Iilustrated Parts Lists

4-24 wt-scon a BA, cea a ++ ree 4 cas

no 4kche=

ci g

|F2h

Ee

Feo*lo Ft
SI critcoe R193¢-—_L Rie
e41K RIO eferyFTH taF Cee
3cersaanes-anusttidF £63
Bee£Rey
~2} s0bbs
el]lasiS CosaL wet
llig+-F fro
¥peeeLs5CY
2 carsCancs B55,Se
Lluae TTTrer LF Ree
gtoe8
xaa5r10K

& Eb sy ttt ew op

“ Paoea
LuiZe3s a aEe
alFf35R104 gary C58 |
384 ot MF og of FROD
ee. 354Lipset]637AE cvs BFD 4
Bo] | |+a3 4a aee#7
8TonzostR324=F as Eaof&
703. Fq gi) |aS te OLr
oF pstJeri es ce EP
23 456

Figure 4-7 Stand-Alone Audio PCB Assembly A043713-24 B Toobin’

Page 55

Toobin’ Mlustrated Parts Lists

Stand-Alone Audio PCB Assembly Parts List

LocationDescriptionPart No.

Integrated Circuits

1J-CPUIntegrated Circuit, 6502 A90-6013
1M-SCOMIntegrated Circuit, SCOM137526-001
23Integrated Circuit, LM32437-1M324
2F-YAMIntegrated Circuit, YM215i137401-001

Integrated Circuit, 6264-15, 150 nsec 137441-002 Integrated Circuit, 27512, 300 nsec 136061-1141 Integrated Circuit, Programmed PALIGL8 A, 25 ns 136056-2101 Integrated Circuit, 7418374 37-7ALS374

3KIntegrated Circuit, POKEY137430-001
4A, 4BIntegrated Circuit, LM32437-LM324
4MIntegrated Circuit, 74LS138137177-001
5C, SEIntegrated Circuit, 4066B37-4066
5F, 5HIntegrated Circuit, 741527337-741S273
SJIntegrated Circuit, 7415240137251-001
5KIntegrated Circuit, 74187437-74LS74
gIntegrated Circuit, 741$39337-74LS393
ALTCLKIntegrated Circuit, 741839337-74LS393

Capacitors

clCapacitor, .22 iF, 50 V, Ceramic122015-224
c2Capacitor, 22 pF, 35 V, Electrolytic24-350226
C3Capacitor, .22 F, 50 V, Ceramic122015-224
C4Capacitor, .1 pF, 50 V, Ceramic122002-104
csCapacitor, 22 pF, 35 V, Electrolytic24-350226
C6-C9, C12Capacitor, .1 pF, 50 V, Ceramic122002-104
C13-C16Capacitor, 100 pF, 100 V, Ceramic122016-101
cl7Capacitor, .1 pF, 50 V, Ceramic122002-104
C18-C21Capacitor, 3300 pF, 25 V, Electrolytic, Radial123003-338
C23Capacitor, .1 pF, 50 V, Ceramic122002-104
C24Capacitor, 10 pF, 25 V, Electrolytic24-250106C25
C25Capacitor, .22 pF, 50 V, Ceramic122015-224
C26Capacitor, .1 pF, 50 V, Ceramic122002-104
C27Capacitor, 10 pF, 25 V, Electrolytic24-250106
C28Capacitor, .1 pF, 50 V, Ceramic122002-104
C29Capacitor, .22 pF, 50 V, Ceramic122015-224
C30Capacitor, .1 pF, 50 V, Ceramic122002-104
C31Capacitor, 10 pF, 25 V, Electrolytic24-250106
C32, C33Capacitor, .001 pF, 50 V, Ceramic122002-102
C34, C35Capacitor, .1 pF, 50 V, Ceramic122002-104
C37Capacitor, .047 pF, 100 V, Ceramic122015-473
C38, C39Capacitor, .1 yF, 50 V, Ceramic122002-104
C40Capacitor, .001 pF, 50 V, Ceramic122002-102
C41, C42Capacitor, .1 pF, 50 V, Ceramic122002-104
C43Capacitor, 10 pF, 25 V, Electrolytic24-250106
C47Capacitor, .22 pF, 50 V, Ceramic122015-224
C48-C52Capacitor, .1 pF, 50 V, Ceramic122002-104
Page 56

Ilustrated Parts Lists ‘Toobin’ |

Stand-Alone Audio PCB Assembly Parts List, Continued

LocationDescriptionPart No.
53Capacitor, .0022 pF, 50 V, Axial Ceramic122015-222
54Capacitor, .0027 pF, 50 V, Ceramic122015-272
55Capacitor, .001 pF, 50 V, Ceramic122002-102
C56Capacitor, .0027 pF, 50 V, Ceramic122015-272/
C57Capacitor, .001 F, 50 V, Ceramic122002-102
C58Capacitor, .0022 pF, 50 V, Axial Ceramic122015-222
C61-C68Capacitor, .1 pF, 50 V, Ceramic122002-104
C69Capacitor, 39 pF, 100 V, Ceramic122016-390\
C70Capacitor, 100 pF, 100 V, Ceramic122016-101
C71-C74, C84Capacitor, .1 pF, 50 V, Ceramic122002-104

Diodes

CR1, CR2Diode, 1N4001131048-001
CR3Diode, MV5053, Light-Emitting131027-002
CR4, CRSDiode, 1N4001131048-001
CRODiode, MV5053, Light-Emitting131027-002
CR7-CR10Diode, 1N5401131051-002
CR13Diode, MV5053, Light-Emitting131027-002
CR14, CR15Diode, iN4001131048-001

Inductor

L1Inductor, 100 pH141024-001

Transistors

Ql, Q2Integrated Circuit, TDA2030137301-001
Q4Integrated Circuit, 7905, Standup37-7905
Q5-Q8Transistor, 2N390434-2N3904
Q9, Q10Transistor, 2N5306133033-001

Resistors

R1Resistor, 1 K Ohm, +5%, 1/4 W110000-102
R2Resistor, 10 K Ohm, +5%, 1/4 W110000-103,
R3, R4Resistor, 1 Ohm, +5%, 1/4 W110000-010
RSResistor, 1 K Ohm, +5%, 1/4 W110000-102
ROResistor, 10 K Ohm, +5%, 1/4 W110000-103
R10Resistor, 0 Ohm, 1/4 W110005-001
R11Resistor, 1 K Ohm, +5%, 1/4 W110000-102F
R12Resistor, 470 Ohm, #5%, 1/4 W110000-471F
R13Resistor, 1 K Ohm, +5%, 1/4 W110000-102
R14Resistor, 470 Ohm, +5%, 1/4 W110000-471{
RISResistor, 1 K Ohm, +5%, 1/4 W110000-102]
R16Resistor, 470 Ohm, #5%, 1/4 W110000-471
R17, R18Resistor, 10 K Ohm, +5%, 1/4 W110000-103
R19Resistor, 22 K Ohm, #5%, 1/4 W110000-223
R20Resistor, 1 K Ohm, +5%, 1/4 W110000-102
R2UResistor, 22 K Ohm, £5%, 1/4 W110000-223

4-26

Page 57

Toobin’ Ilustrated Parts Lists

Stand-Alone Audio PCB Assembly Parts List, Continued

LocationDescriptionPart No.
R22Resistor, 10 Ohm, +5%, 1/4 W110000-100
R23Resistor, 560, +5%, 1/4 W110000-561
R24Resistor, 1 K Ohm, 5%, 1/4 W110000-102
R26, R27Resistor, 10 Ohm, +5%, 1/4 W110000-100
R28Resistor, 10 K Ohm, +5%, 1/4 W110000-103
R29Resistor, 1 K Ohm, +5%, 1/4 W110000-102
R33, R34Resistor, 470 Ohm, +5%, 1/4 W110000-471
R35,Resistor, 75 K Ohm, +5%, 1/4 W110000-753
R36, R37Resistor, 10 K Ohm, +5%, 1/4 W110000-103
R38.Resistor, 47 K Ohm, #5%, 1/4 W110000-473
R43-R48Resistor, 12 K Ohm, 25%, 1/4 W110000-123
R49Resistor, 10 K Ohm, +5%, 1/4 W110000-103
R50Resistor, 1 K Ohm, +5%, 1/4 W110000-102
R51, R52Resistor, 10 K Ohm, +5%, 1/4 W110000-103
R53, R54Resistor, 1 K Ohm, +5%, 1/4 W110000-102
R55, R56Resistor, 150 K Ohm, +5%, 1/4 W110000-154
R58Resistor, 1 K Ohm, +5%, 1/4 W110000-102
R59Resistor, 150 K Ohm, 25%, 1/4 W110000-154
ROOResistor, 1 K Ohm, #5%, 1/4 W110000-102
R61Potentiometer, 10 K Ohm, Horizontal, Dual119011-103
RO2Resistor, 7.5 K Ohm, +5%, 1/4 W110000-752
ROBResistor, 30 K Ohm, #5%, 1/4 W110000-303
R64Resistor, 15 K Ohm, +5%, 1/4 W110000-153
ROSResistor, 12 K Ohm, #5%, 1/4 W110000-123
R70Resistor, 75 K Ohm, #5%, 1/4 W110000-753
R71Resistor, 150 K Ohm, +5%, 1/4 W110000-154
R74-R81Resistor, 1 K Ohm, +5%, 1/4 W110000-102
R82Resistor, 470 Ohm, #5%, 1/4 W110000-471
R83Resistor, 150 K Ohm, +5%, 1/4 W110000-154
R84Resistor, 0 Ohm, 1/4 W110005-001
R85AResistor, 470 Ohm, +5%, 1/4 W110000-471
R86Resistor, 220 Ohm, #5%, 1/4 W110000-221
R103Resistor, 150 K Ohm, 25%, 1/4 W110000-154
R104Resistor, 12 K Ohm, +5%, 1/4 W110000-123

Sockets

q-CPUSocket, 40 Pin179257-040
1M-SCOMSocket, 20 Pin179259-020
2DSocket, 16 Pin179259-016
2F-YAMSocket, 24 Pin179257-024
2H-RAM, 2K-ROMSocket, 28 Pin179257-028
3KSocket, 40 Pin179257-040

Connectors

JACDCConnector, 12 Cki, Header, .156-Inch Ctr, Key 11179213-012
JCDLConnector, 2 Ckt, Header, .156-Inch Ctr179213-002
JCOINConnector, 6 Ckt, Header, .100-Inch Ctr, Key 2179118-006

4-27

Page 58

Illustrated Parts Lisis

Stand-Alone Audio PCB Assembly Parts List, Continued Toobin’

LocationDescriptionPart No.
JSCOMConnector, 11 Ckt, Header, .100-Inch Ctr, Key 5179118-011
JSPKConnector, 6 Ckt, Header, .156-Inch Ctr, Key 3179213-006

Miscellaneous

HSLHeat Sink, TDA2030178190-032
HSRHeat Sink, TDA2030178190-032
sWiSwitch, Slide, SPDT160040-001
x1Crystal, 3.579 MHz Standup144007-001

Test Point 179051-001

Page 59

Toobin’ Statistics: Date _

Left Coins Right Coins New Games Continuation O Plyr Mins 1 Plyr Mins 2 Plyr Mins New Mins Game Statistics (Refer to Chapter 2 of the operators manual for clarification of these terms)

Cont Mins Sessions Error Count Total Coins Avg Time/Coin Avg Time/New Game Avg Time/Cont Game

Histogram Information

Length of Game in Seconds 0-39 40-59 60-79 80-99 100-119 120-139 140-159 Number of Games

Length of Game in Seconds 0-39 40-59 60-79 80-99 100-119 120-139 140-159 Number of Games

Length of Game in Seconds 0-39 40-59 60-79 80-99 100-119 120-139 140-159 Number of Games New Easy Games Length of Length of

Game inNumberGame inNumber
Secondsof GamesSecondsof Games

160-179 300-319 180-199 320-339 200-219 340-359

220-239360-379———
240-259380-399———

260-279 400 & Up 280-299 —

New Medium Games Length of Length of

Game inNumberGame inNumber
Secondsof GamesSecondsof Games

160-179 300-319 180-199 320-339 200-219 _ 340-359 220-239 360-379 240-259 380-399

260-279_400 & Up

280-299 —

New Hard Games Length of Length of

Game inNumberGame inNumber
Secondsof GamesSecondsof Games

160-179 300-319 180-199 320-339

200-219_340-359~—
220-239360-379——
240-259380-399—____
260-279_400 & Up_

280-299

Page 60

Histogram Information, Continued

Length of Game in Seconds 0-39 40-59 60-79 80-99 100-119 120-139 140-159 Number of Games

Length of Game in Seconds 0-39 40-59 60-79 80-99 100-119 120-139 140-159 Number of Games

Length of Game in Seconds 0-39 40-59 60-79 80-99 100-119 120-139 140-159 Number of Games

Length of Game in Seconds 0-39 40-59 60-79 80-99 100-119 120-139 140-159 Number of Games Continued Easy Games Length of Game in Seconds 160-179 180-199 200-219 220-239 _ 240-259 260-279 280-299 Number of Games

Continued Medium Games Length of Game in Seconds 160-179 180-199 200-219 220-239 240-259 260-279 280-299 Number of Games

Continued Hard Games Length of Game in Seconds 160-179 180-199 200-219 220-239 240-259 260-279 280-299 Number of Games

Session Length Length of Game in Seconds 160-179 180-199 200-219 __ 220-239 240-259 260-279 280-299 Number of Games Length of Game in Seconds 300-319 320-339 340-359 360-379 380-399 400 & Up

Length of Game in Seconds 300-319 320-339 340-359 360-379 380-399 400 & Up

Length of Game in Seconds 300-319 320-339 340-359 360-379 380-399 400 & Up

Length of Game in Seconds 300-319 320-339 340-359 360-379 380-399 400 & Up Toobin’

Number of Games

Number of Games

Number of Games

Number of Games

Page 61

AC Alternating current; from zero it rises to a maximum positive level, then passes through zero again to a maximum negative level.

ACTIVE STATE The true state of a signal. For example: ‘The active state for is low.

ADDRESS A value that identifies a specific location of data in memory; normally expressed in hexadecimal notation. ANALOG Measurable in an absolute quantity (as opposed to on or off). Analog devices are volume controls, light dimmers, stereo amplifiers, etc. ANODE The positive (arrow) end of a diode. AMPLIFIER A device used to increase the strength of an applied signal. AMPLITUDE The maximum instantaneous value of a waveform pulse from zero. ASTABLE Having no normal state. An astable device will free-run or oscillate as long as operating voltage is applied. The oscillation frequency is usually controlled by external circuitry. AUXILIARY COIN SWITCH A momentary-contact pushbutton switch with a black cap located on the utility panel. The auxiliary coin switch adds credits to the game without activating a coin counter. BEZEL A cut, formed, or machined retention device, such as the conical device used to mount a pushbutton switch to a control panel, or the formed device used to frame the video display screen, BIDIRECTIONAL Able to send or receive data on the same line (e.g., the data bus of a microprocessor). BINARY A number system that expresses all values by using two digits (0 and 1). BIT A binary digit; expressed as i or 0. BLANKING Turning off the beam on a cathode-ray tube during retrace. BLOCK DIAGRAM ‘A drawing in which functional circuitry units are represented by blocks. Very useful during initial troubleshooting. BUFFER 1, An isolating circuit designed to eliminate the reaction of a driven circuit on the circuits driving it (e.g., a buffer amplifier).

  • A device used to supply additional drive capability. BUS An electrical path over which information is transferred from any of several sources to any of several destinations.

CAPACITOR A device capable of storing electrical energy. A capacitor blocks the flow of DC current while allowing AC current to pass. CATHODE The negative end of a diode. CHIP An integrated circuit comprising many circuits on a single wafer slice. CLOCK A repetitive timing signal for synchronizing system functions. COINCIDENCE Occurring at the same time. COIN COUNTER A 6-digit electromechanical device that counts the coins inserted in the coin mechanism(s).

COIN MECHANISM A device on the inside of the coin door that inspects the coin to determine if the correct coin has been inserted.

COMPLEMENTARY Having opposite states, such as the outputs of a flip-flop. COMPOSITE SYNC Horizontal and vertical synchronization pulses that are bused together into a single signal. This signal provides the timing necessary to keep the display in synchronization with the game circuitry.

Glossary

COMPOSITE VIDEO Complete video signal from the game system to drive the display circuitry, usually comprising H SYNC, V SYNC, and the video. CREDIT One play for one person based on the game switch settings. CRT Cathode-ray tube. DATA General term for the numbers, letters, and symbols that serve as input for device processing. DARLINGTON A two-transistor amplifier that provides extremely high gain.

DC Direct current, meaning current flowing in one direction and of a fixed value.

DEFLECTION YOKE Electromagnetic coils around the neck of a cathode-ray tube. One set of coils deflects the electron beam horizontally and the other set deflects the beam vertically. DIAGNOSTICS A programmed routine for checking circuitry. For example: the self-test is a diagnostic routine. DIODE A semiconductor device that conducts in only one direction. DISCRETE Non-integrated components, such as resistors, capacitors, and transistors. DMA Direct memory access. DMA is a process of accessing memory that bypasses the microprocessor logic. DMA is nozmally used for transferring data between the input/output ports and memory. DOWN TIME ‘The period during which a game is malfunctioning or not operating correctly due to machine failure. EAROM Electrically alterable read-only memory (see ROM). The EAROM is a memory that can be changed by the application of high voltage.

gl-l

Page 62

FLYBACK A step-up transformer used in a dispiay to provide the high voltage. GATE

  • A circuit with one output that responds only when a certain combination of pulses is present at the inputs.
  • A circuit in which one signal switches another signal on and off.
  • To control the passage of a pulse or signal. HARNESS A prefabricated assembly of insulated wires and terminals ready to be attached to a piece of equipment. HEXADECIMAL A number system using the equivalent of the decimal number 16 as a base. The symbols 0-9 and A-F are usually used. IMPLODE To burst inward; the inward collapse of a vacuum tube, vo Input/Output. IRQ Interrupt request. IRQ is a control signal to the microprocessor that is generated by external logic. This signal tells the microprocessor that external logic needs attention. Depending on the progiam, the processor may or may not respond, LED The abbreviation for a light-emitting diode. LOCKOUT COIL Directs coins into the coin return box when there is no power to the game. LOGIC STATE The binary (1 or 0) value at the node of a logic element or integrated circuit during a particular time. Also called the logic level. The list below shows the voltage levels corresponding to the logic states (levels) in a TTL system. Logic 0, Low = 0 VDC to +0.8 VDC Grey Area (Tri-State Level) = +0.8 VDC to +2.4 VDC Logic 1, High = +2.4 VDC to +5 VDC MULTIPLEXER A device that takes several low-speed inputs and combines them into one high-speed data stream for simultaneous transmission on a single line.

gl-2 NMI Non-maskable interrupt. NMI is a request for service by the microprocessor from external logic. The microprocessor cannot ignore this interrupt request. PAGE A subsection of memory. A read-only memory device (see ROM) is broken into discrete blocks of data. These blocks are called pages. Each block has X number of bytes. PCB The abbreviation for a printed-circuit board, (e.g., the ATARI® CAT Box) convert lengthy bit streams into four-digit hexadecimal signatures. The signature read by the analyzer at each circuit node is then compared with the known good signature for that node. This process continues until a fault is located. TROUBLESHOOT The process of locating and repairing a fault. VECTOR A line segment drawn between specific X and Y coordinates on a cathode-ray tube.

PHOTOTRANSISTOR WATCHDOG by an external light source. A *%, designed to

A transistor that is activated ta a ak A counter circuit

POTENTIOMETER 7 protect the

  • A resistor that has a continuously moving contact which is generally mounted on a moving shaft. Used chiefly as a voltage divider. Also called a pot (slang).
  • An instrument for measuring a voltage by balancing it against a known voltage. RAM Random-access memory. A device for the temporary storage of data. RASTER-SCAN DISPLAY A display system whereby images are displayed by continuously scanning the cathoderay tube horizontally and vertically with an electron beam. The display system controls the intensity of the electron beam. RETRACE In a raster-scan display, retrace is the time during which the cathode-ray tube electron beam is resetting either from tight to left or from bottom to top. RESISTOR A device designed to have a definite amount of resistance. Used in circuits to limit current flow or to provide a voltage drop. ROM Read-only memory. A device for the permanent storage of data. SIGNATURE ANALYSIS A process of isolating digital logic faults at the component level by means of special test equipment called signature analyzers. Basically, signature analyzers Mh microproi cessor

from self-destruction if a program malfunction occurs. If a malfunction does occur, the counter applies continuous pulses to the reset line of the microprocessor, which causes the microprocessor to keep resetting. X-Y DISPLAY ‘A display system whereby images are displayed with vectors. ZENER DIODE A special diode used as a regulator. Its main characteristic is breaking down at a specified reverse-bias (Zener) voltage.

Page 63

somngpisip yons Aq pouuoyed s} uRps Joge| Supnpur vonRoyrpow Aue Jo ued pery-uoU Aue jo 4 Anod guhsua oF Japlo ui ‘saue8 mo quia swauodmos parddnsqey-sou Buy -sti uy snoring A7aA ag ‘stato pur NOA oy Arniu; anes puE oUTED 3NOA Jo AjaTES Se a eee Ny te Beer ee re eee eeu ea sus) atp 0} Surpyosoe “AueueM nod pron Amu sued wery-uoU Aue yo asn ot . 4aye5 Aq sionposd Jo apps ag) qr HoONoeUMO? uy saLNGiny dao Kup spas emi sof alunssy 9 uosied souo Gur seme ~oyInD 4ou SoUINSSP saqOU tt pun ‘und S4o]JaS aql UO SaLnpqD} 40 suoNDEGO woqo ye fo pup ‘asodind sojnoiued p sof ssounf pur Giypqotupgo.au fo sosuns am. paydus agi Fuipnyour ‘peyduy 40 passeudca sane saqio yo fo vagy sp passaudxa st (rune sa) ‘utadaq suLial acy sepasiadns sopauos qaign JAC PUP saypesy. uaamjaq yao? uayLum Dp ut quol tes Gunsnm ssaidea Cup sof waa “safviuep pepvanbes YOO JO JEIBOPIOU! ‘asn JO sso} “siyOIT JO sso] JOY a]qEH aq JaY[Eg [TeYs Weae ou UT ‘Bunsay sadosdunt so. ‘uoneymsul ‘sedas sodosdunr ‘uopesae hpalfou ‘asnsnu uapioat Aq pasnes JOU aie puE polsrxa sHayap pafeye yons IEP VOOUISHES stafjes oO} Sesopsip smaped pres JO UOMEUIEXe stayjpg (9) pure cued szajps o predaad paummar are sonipard yang (q) ‘panoajap ore sionpord pres ail sadng Aq Aisaonsip uodn Supp oy pagpou Apdeuord sy sayjag Ce) -o1d ‘poped Aqueren. pres Sapp Joyjas on pawiniay oe Gory Sionposd yons Joy Tnosse suaing wpe so ‘eseday redex OF “uoRdo sy re ‘Sq TTeYys Gmqer sjos S2ayfag AURA Sit) OF WUOJUOD O} []Ry [ENUVUN STI Gt paquosap s~npoid otp 51 "PMUEUEA st josiswp sued JO sionpold sorpo szayjes atp jo ation awawidyys jo aep woy skep.(o¢y Aunp yo porad ¥ Joj aa}Alas pue asf jetuGU Jopun diysurinpom pue fepeietu wi sbayep uloy aay sue (siaxud osrp-oopla pun skujdsip ipia payddns sawed u}) siedejd Is7p opprasasr] por Shtjdsip oapia si iy) SIUTLEAL Jalfag TuadiYs Jo ap Woy Shep (9g) Arm JO poled # toy aojaras pur asn yemouJopun drysueunpOA pur yeLaTeN U1 S192) ap Woy Say ase. UOsrey sued put spieoq imMdn5-permnd sip ietp SivesseAs Joljag AQUVLIE AA

Page 64

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.