CATHODE RAY TOMES

Ridge Racer 2

Ridge Racer 2 (World, RRS2) (Namco, 1994) · Document · 22 pages · 3 sections · original scan

Page 1

Part No 90500075

Page 2

© 1993,1994 PRAMEO ce - au rights reserved.

No part of this publication may be reproduced by any mechanical, photographic or electronic process, or in the form of phonographic recording, nor may it be stored ina retrieval system, transmitted or otherwise copied for public or private use, without permission from namco Ltd.

While the information contained in this manual is given in good faith and was accurate at the time of publication, BRENT LEISURE LIMITED reserve the right to make changes and alterations without notice.

No responsibility is accepted for unauthorized changes or modifications made to the machine.

Published by: BRENT LEISURE Ltd. Unit 1 Brent Crescent, London. NW10 0QT

Phone:- 081-965-0550 Fax:- 081-961-0574

Page 3

1. 2. 3. Operators Manual «1 SPECIFICATIONS 5 MAJOR COMPONENTS 6 PRECAUTIONS. 7 3-1 Cautions When Installing 7 3-2 Caution when Handling. . 7 3-3 When Transporting. . 7 INSTALLATION ..... ee 8 4-1 Connecting the Seat Assemblies to the Cabinet. 8 4-2 Adjusting the Level Adjusters 8 ADJUSTMENTS 8 5-1 Turning on the Power.. 8 5-2 Switches for Adjustments .. 8 5-3 Test Mode 9 Contents

5-3-1 Setting the Game Fee and So On (On the Coin Options Screen) 5-3-2 Changing the Game Settings (on the Game Options Screen) . 5-3-3 Switch Test. 5-3-4 Sound Test (Adjusting the Sound Volume) . 5-3-5 LAMP TeSt ss. ccceccescecicetsceeveavennnesesnacvnrs cate vete 5-4 Adjusting the Game After Replacing Parts (Initializing the Game) 5-5 CONNECTING MULTIPLE GAME LINKS HOW TO PLAY MAINTENANCE ... 7-1 Replacing Fluorescent Lamps 7-2 Replacing the Leading Driver Lamps . 7-3 Removing the Game Printed Circuit Board (PCB) . 18 7-4 Removing the Shield Case ... 19 7-5 Removing the Power Control Panel 19 7-6 AB Pedal Assy (Replacing the Control) . 19 7-7 Gear Shift Assy (removing)... 19 7-8-1 Replacing the control ........ 7-8-2 Replacing The Steering Wheel

Page 4
  • SPECIFICATIONS

POWER SUPPLY :-

MONITOR:auto degauss.

DIMENSIONS :- When Assembled:- Cabinet:- Seat Assy:-

WEIGHT :- When Assembled:- Cabinet:- Seat Assy:-

ACCESSORIES :- 220/240volts AC

Hantarex 28" Polo Colour Monitor with

1400(w) x 1770(d) x 1980(h) 1400(w) x 920(d) x 1980(h) 470(w) x 940(d) x 1230(h)

310kg 250kg 30kg (ea)

Keys: (Cash Door) 2 (Coin Assy) 2 (Back Door) 2ea

M10x30 Hex Head Bolts 24 M10 Flat Washer 24 M10 Spring Washer 24 Seat/Cabinet Joint Bracket 4

Phono Link Lead 1

IEC mains Lead 1

Operators Manual 1

Page 5
  • MAJOR COMPONENTS

Top Flash

Rear door

Switching regulator Dashboard Assy

Gear Shift

Steering Assy

Mains In & Link Board

Page 6
  • PRECAUTIONS

3-1 Cautions When Installing.

This game is designed for indoor use only. The game must not be installed outdoors or under the following conditions:-

a. In areas directly exposed to sunlight, high humidity, direct water contact, dust, high heat or extreme cold.

In locations that would present an obstacle in the case of an emergency, i.e.. near fire equipment or emergency exits.

On an unstable surface or subject to floor vibration.

3-2 Caution when Handling.

a. AC power must always be turned OFF, and the game disconnected, before replacing any parts or connecting/disconnecting connectors.

When unplugging the game from an electrical outlet, always grasp the plug, not the mains lead.

The machine must be earthed with a securely connected earthed plug.

Care must be taken at all times to avoid electric shock when inspecting or adjusting the game.

Adjustment is required whenever the game PCB board, ROM, Steering Assy, AB pedal Assy or control are replaced. (See 5-4 "Adjusting the Game After Replacing Parts" on page 10)

3-3 When Transporting.

a.

b. Do not subject the game to physical shock when transporting or moving it.

Always return the levellers to the UP position before moving the machine.

Take care not to rope any moulded (plastic) parts when transporting.

Always separate the seat assemblies from the cabinet before moving or transporting.

Page 7
  • INSTALLATION

Remove from the cash box the four joint plates, 240ff M10x30 hex head bolts, 24off M10 flat washers and 24off M10 spring washers.

4-1 Connecting the Seat Assemblies to the Cabinet

  • Place the cabinet in the installation position.
  • Connect the connectors from the cabinet to the connectors in the seat assemblies.
  • Fix the seat assemblies to the cabinet using the joint plates, M10 hex head bolts, flat washers and spring washers taking care not to trap any wires between the seat assemblies and cabinet.

4-2 Adjusting the Level Adjusters

Adjust the level adjusters of the cabinet and seat assemblies (four each for the cabinet and each seat assembly) with a wrench (24mm) so that the castors are raised from the floor by about 5mm. Ensure the machine is level and stable then back up the lock nut to lock the adjuster.

  • ADJUSTMENTS

5-1 Turning on the Power

After installing the product, turn on the power. The power switch is located above the mains inlet on the rear of the cabinet.

5-2 Switches for Adjustments

Open the coin door for access to the switches for adjustments.

  • Service Switch Press this switch to establish credits without incrementing the coin counter.
  • Test Switch Set this switch to "ON" to enter test mode. You can change the price of play and perform various tests in Test Mode. (See "5-3 Test Mode" on page 5)

COIN COUNTER—_| °

Ler RIGHT PLAYER LEEAYER nicht LEFT RIGHT. |_ — SEAT VOLUME OO 007

mio

Page 8

5-3 Test Mode

  • Open the coin door, set the test switch to "ON". The "Menu Screen" appears on the monitor display.
  • Select the item to be tested by turning the steering wheel right or left. The colour of the item you select changes.
  • Step on the accelerator pedal to display the menu of the selected item. To return to the “Menu Screen” step on the brake pedal
  • When the test finishes, set the test switch to “OFF” to return to the Game Screen.

The Test switch must always be “OFF” during normal game mode.

MENU

COIN OPTIONS

GAME OPTIONS

BOARD TEST

SWITCH TEST

SOUND TEST

MONITOR TEST

ADS TEST

PCG TEST

LAMP TEST

ABOUT

IN=STEP ON THE GAS (a)

(b)

(c)

(d)

(e)

(f)

(g)

(h)

@

@ For setting the price of play (see 5-3-1)

setting the game options (see 5-3-2)

testing the game PCB

testing switches (see 5-3-3)

adjusting the sound volume (see 5-3-4)

monitor adjustments

displaying game data collected

testing game graphics

testing leading driver lamps

restoring each setting to standard value

Page 9

Select 1 “COIN OPTIONS” on the Menu Screen to set the game fee

Turn the steering wheel to select the item to be changed, then 5-3-1 Setting the Game Fee and So On (On the Coin Options Screen)

COIN OPTIONS

GAME COST

2 COINS | CREDIT (a) step on the accelerator pedal. COIN 1 MECH VALUE

Turn the steering wheel again to 1 COIN COUNT AS 1 COIN (b) change the setting, then step |coin 2 MECH VALUE on the accelerator pedal (See table 1.) 1 COIN COUNT AS 1 COIN (c)

Step on the brake pedal to return BONUS FOR QUANTITY BUY-IN to the Menu Screen. NONE @)

FREE PLAY

Note: ‘The price of play OFF (e) adjustments are made on the credit dispense board (located inside the coin door) |EXIT = STEP ON THE BRAKE and the coin options should be set as the following table.

Item Description

(a) Game feeNumber of credit pulses necessary for game creditOne to nineSet to 1
(b) Coin 1 mechanism | Number of credit pulses per coinOne to nineSet to 1
  • Coin 2 mechanism | Not Used One to nine
  • Bonus The extra credit given as a bonus when the specified | One credit per one coin
number of coins are insertedThree credits per nineSet to NONE

coins

(e) Free playFree play started by stepping on the acceleratorOFF/ONset to OFF
Page 10

5-3-2 Changing the Game Settings (on the Game Options Screen)

Select 2 “GAME OPTIONS” to Tanaris

change the game options.(DEFAULTINOREN)
Turn the steering wheel to select_aban>
the item to be changed then stepEXPERT>
on the accelerator pedal.cams:
Turn the steering wheel again toover:7
change the setting,then step onperms+s)
the accelerator pedalae:a
(see table below).LINKABLE:a
Step on the brake pedal to returnsony_antmacton|

to the Menu Screen. OO

Set the rank and number of laps the — . °

same for each connected—,”
machine. Set the CPU numbersEXIT=STEP ON THE BRAKE

starting in ascending order with

Settings of the Game Options Screen

Ttem| Description Factory setting

(a) Play time for the novice level‘A (shortest) to H (longest)D
  • Play time for the advanced level ‘A (shortest) to H (longest)
(©) Play time for the expert levelA (shortest) to H (longest)D
(d) Play time for the time trial game‘A (shortest) to H (longest)D
(©) Play time for linked game‘A (shortest) to H (longest)D
(f) Laps for the novice level21052
(g) Laps for the advanced level21053
(h) Laps for the expert level20053
(Laps for the time trial game20053
(j) Laps for the linked game20053

KMH (Kilometers per Hour)

  • Unit of speed MPH (Miles per Hour) Set for Country of Use
(D) Attract soundON/OFFON
(m) CPU No.0107Setin farsi from
(n) Car type1 BLUE1 BLUE - Left Player

2 YELLOW 2 YELLOW - Right Player 3RED 4 GREEN When linked to other 5 BLUE ‘machines set to player No. 6 YELLOW

7RED 8 GREEN

Displays number of linked

orrne0d Gonmachines. If there is a

problem or only one seat set, (NG) will be displayed.

Page 11

5-3-3 Switch Test

Select 3 “SWITCH TEST” to display the following screen.

SWITCH TEST

DIP SW2 12345678 (a) Option switch (SW2 on the CPU) SW3 12345678 (b) Option switch (SW3 on the CPU)

STEERING—*0000(©) Steering
GAS*0000(d) Accelerator
BRAKE*0000(©) Brake
SHIFTCENTRE SWITCHIOFF|(f Shift

SWITCH2 OFF

SERVICEOFF(g) Service switch
COIN1OFF(h) Coin 1 switch
COIN2OFF() Coin2 switch

EXIT = STEPON THE BRAKE

AND ACCELERATOR

a. The status of the option switch SW2 on the game PCB (CPU-PCB) is indicated here. b. The status of the option switch SW3 on the game PCB (CPU-PCB) is indicated here. The SW2 or SWS switch is set to ON when the corresponding number is red. c. When you turn the steering wheel to the right, the number increments. When turning it to the left, the number decrements. d. When you step on the accelerator pedal, the number increments. e. When you step on the brake pedal, the number increments. An approximate value of “0000” appears on the item c, d or e respectively when you locate the steering wheel in the middle and when the accelerator and brake pedals are released. (Even if the least digit of the number changes, the game is operating normally). “OK” appears to the right of the number when the accelerator and brake pedals are depressed. f. The position of the shift and the status of two switches are indicated here. When you move the shift lever to low CENTRE changes to DOWN and switch 1 is set to ON. When you move it to high Centre changes to UP and switch 2 is set to ON. h. ”ON” appears when you press the service switch inside the coin door. i. “ON” appears when you operate the credit available button only if credits are established on the dispense board. j. Not used.

To return to the Menu Screen, step on both the brake and gas pedal at the same Pdigee 8

Page 12

5-3-4 Sound Test (Adjusting the Sound Volume)

Select “SOUND TEST” on the menu screen to adjust the sound volume. The following screen appears.

SOUND TEST

VOLUME(L) 3F (a) Sound volume for left speakers

VOLUME(R) 3F (b) Sound volume for right speakers

STEREO CHECK (c) Stereo checking function

SONG 00

EXIT=STEP ON THE BRAKE

Use the steering wheel to select the item to be changed. Step on the accelerator and the item selected will stop flashing. Use the steering to adjust the level. Step on the accelerator when the desired setting is reached and the item will start flashing. The steering can now select another item.

The sound volume can be adjusted in 64 steps between 00 (minimum) to 3F (maximum). The factory setting is “SF”. (i.e. Loudest)

When you select (c) and step on the accelerator pedal, sound is produced the left speaker, then the right speaker. Step on the brake pedal to return to the Menu Screen.

The volume controls on the service bracket enable the seat speakers to be reduced from the main volume.

5-3-5 Lamp Test

The Leading Driver Lamps will turn ON or OFF each time the accelerator pedal is pressed.

Page 13

5-4 Adjusting the Game After Replacing Parts (Initializing the Game)

Be sure to adjust the game with the following instructions below after replacing any part. Otherwise, the game will not function correctly.

  • Ensure that the accelerator and brake pedals are released and the steering is in the centre.
  • Slide the test switch to “ON” while pressing the service button. The following screen appears on the monitor display.

ADJUST

STEERING 0000

GAS 0000

BRAKE 0000

  • To zero the settings press the service switch.
  • When each number on the right hand side of the items: STEERING, GAS and BRAKE is about “0000”, the adjustments are complete.
  • Set the test switch to “OFF” to return to the Game Screen.

The test switch must always be “OFF” during normal game mode.

Page 14

5-5 CONNECTING MULTIPLE GAME LINKS

ONE GAME When installing more than one Ridge Racer 2™ game, the units must be linked using screened audio cable (One lead is supplied with each machine)

Ensure that all leg levellers on the game cabinets and seats have all been lowered, and that all castors are clear of the floor. Make sure that power to all the games is turned OFF.

To link multiple cabinets (2-4 units), locate the LINK PCB, mounted next to the mains-in socket (remove the cover plate to gain access), on each Game Cabinet, and move all slide switches to the "External" (Right) position.

NOTE:- A single cabinet (not linked) must have the slide switch set to the "INTERNAL" (Left) position. If not, the two players will not link.

Using the appropriate diagram below, connect the link cables provided from "IN" to "OUT" between each of the game units to be linked.

TWO

®©®©©©GAMES
ourINouroNouTIN
0i)A0

THREE © GAMES our ® 2© © 2© our e z

FOUR GAMES

eo©®eo©®eo©®eo©®
ouroNouroNourINour

z

NOTE: Initialize each car (see 5-4 Page 10). Do this for each car.

Enter the test mode, and using the Option Screen, set the CPU No. and Car Type for each unit. (See 5-3-2, Page 7 "Game Option Screen", for more information).

  • Each car must have a different CPU and Car Type number for proper operation.
Page 15
  • HOW TO PLAY

Players can race by themselves against the computer or head to head on the same track. With four machines linked, up to 8 players can race on the same track.

Four difficulties are provided. NOVICE, INTERMEDIATE, ADVANCED and T.T.(Time Trials), with up/down gear shift or fully automatic transmission.

(Outline of a Game)

When a player drives a car the specified number of laps within the given time, they finish the race, the ranking, lap time and total time are displayed and the game is over.

If the countdown timer reaches 00 before a player finishes the race, the game is over.

(Starting a Game)

Insert coins, and press the credit available button for each driver. Turn the steering wheel to select MANUAL or AUTOMATIC then press the accelerator. Turn the steering wheel to select NOVICE, INTERMEDIATE, ADVANCED or TT then press the accelerator. A linked game starts when all linked seats have been entered, or when 20 seconds have elapsed since the first credit available button was pressed.

(Difference of Difficulty Levels)

When a player selects the NOVICE level, he or she drives a car on the MAIN COURSE at a low speed. This is the player’s car vs. computer driven cars race game.

When a player selects the INTERMEDIATE level, he or she drives a car on the MAIN COURSE at a high speed. This is the player’s car vs. computer-driven cars race game.

When a player selects the ADVANCED level, he or she drives a car on the MAIN COURSE and a TECHNICAL BRANCH ata high speed. This is the player’s car vs. computer-driven cars race game.

When a player selects the TT level, he or she drives a car on the MAIN COURSE and the TECHNICAL BRANCH at a higher speed than that of the ADVANCED level. This is the player’s car vs. a computer-driven car or other player's time trial race. When a player clocks a good time, they can record their name.

When drivers are driving against each other in LINK mode, they drive on the intermediate level.

Page 16
  • MAINTENANCE

7-1 Replacing Fluorescent Lamps

  • Remove the ten M5x16 button head screws, and remove the top flash (see fig. below). taking care to unplug the 2 Leading Driver Lamp plugs.
  • Replace the fluorescent lamp and/or starter.

7-2 Replacing the Leading Driver Lamps

  • Remove the ten M5x16 button head screws, and remove the top flash (see fig. below). taking care to unplug the 2 Leading Driver Lamp plugs.
  • Replace the lamps. (12v 2.2w Wedge Lamps)

(M5x16) Screw

Acrylic sign

LLL LALLA SULLLLLLLLLLUMLL dds

ULL

Xenon lamp

Leading Driver Lamp

Page 17

7-3 Removing the Game Printed Circuit Board (PCB)

1. Remove the back door,

Remove two assembling bolts (M6 x 30), then pull out the power control panel about 25cm. (Note: if you pull it out too much, it will be detached).

Disconnect two connectors on the EMI board, then remove six cup screws (M4 X 10) from the shield case door. (Do not lose internal washers).

Take care not to damage the connectors between the EMI board and the main PCB to remove the shield case door, then take out the main pcb.

Remove two cup screws (M4 X 10) from the I/O door. (Note: Do not remove other screws).

Remove the I/O door, then disconnect four connectors of the I/O PCB.

Take out the I/O PCB. Shield case Back cover (L)

Cup screw (M4 x 10)

Assembling bolt (M6 x 30) Angle bracket

‘Power control “s panel rie ee

Shield case door

Main PCB Cup screw (M4 x 10) AC fan

EMI board”

Ground terminal __

an Internal washer (M4) Cup screw (M4x 10) / CU

Page 18

7-4 Removing the Shield Case

1.

2.

3. Perform Steps (1) and (2) described in Section 7-3.

Disconnect the connector of the AC Fan.

Remove two cup screw (M5 x 14) then take out the shield case.

7-5 Removing the Power Control Panel

2. Perform steps 1, 2, 5 and 6 described in Section 7-3.

Disconnect two connectors of the EMI board, remove a cup screw (M4 X

  • from the shield case door, then remove the ground terminal. (Note: do not lose the internal washer).

Disconnect the connectors connecting the power control panel and the main body assy: one connector on the right side and two connectors on the left side then remove the power control panel.

7-6 AB Pedal Assy (Replacing the Control)

1.

2. Remove four hex head bolts (M6x20) and withdraw the assy forward .

Loosen the quadrant gear clamp screw and remove the quadrant gear.

Loosen the gear grub screw and remove the gear.

Replace the control potentiometer.

Note: When reassembling a. Ensure that the potentiometer locating tag is engaged in the mounting plate cutout. b. Turn the potentiometer shaft almost fully clockwise before engaging the quadrant gear.

7-7 Gear Shift Assy (removing)

1.

2. Remove 4off M5x20 button head screws and pull forward the play panel assy and disconnect the four way connector on the gear shift assy.

Remove four M4 coach bolts and withdraw the shifter assy.

Re-initialize the game (see 5-4 Page 10 "Adjusting the Game") whenever the game PCB board, ROM, Steering Assy, AB Pedal Assy or Controls are replaced before the game is played.

Page 19

7-8 Steering Assy

7-8-1 Replacing the control

  • Remove 4off M5x20 button head screws and pull forward the play panel assy to gain access to the steering assy.
  • Loosen the grub screw on the gear wheel and remove the gear wheel.
  • Replace the control potentiometer.
  • Replace the gear wheel and re-tighten the grub screw securely.
Note: When replacing the control potentiometer ensure that the locating tag of the potentiometer is located in the hole in the mounting bracket and the pot shaft is at its mid travel before tightening the gear grub screw.

7-8-2 Replacing The Steering Wheel

  • Remove the centre cover of the steering wheel.
  • Remove three socket button heads (M6x16)
  • Pull off the steering wheel, then replace it with a new one.

Re-initialize the game (see 5-4 Page 10 "Adjusting the Game") whenever the game PCB board, ROM, Steering Assy, AB Pedal Assy or Controls are replaced before the game is played.

Page 20
  • PARTS

CABINET SEAT ASSY

Description Part No. Description Part No.

Monitor 28" Hantarex Polo84000012Seat - (black)88300630
Speaker 4 1/2" 20w (with shield can) | 62000006Seat Slider Mechanism88300680
Speaker - Piezo Horn62000046Speaker 4 1/2" 20w62000006
Dual Pedal Assy (with pots)88800029Speaker Cover Plate (Left)88300603
Dual Pedal Assy Control Pot (Sk)76000652Speaker Cover Plate (Right)88300604
Steering Assy (270 deg)88800001MI6 Adjustable Foot88300079
Steering Control Pot (5k)7600065275mm Castor59000005

Steering Wheel 88800008

Gear shift Assy 88800009

Credit Available Button Assy 60200215

Power Supply Assy - 5v/30amp 83000004.

Schaffner Mains Filter Input Assy 66000016

Fuse 5a 20mm 63500601

Interlock Switch 60000006

Fan67000015VAC-FORMS/ACRYLIC/DECALS

Front Glass 31000019

1000hm 10w W/W Volume Control76000164peseriptionpaar Ne
Slide Switch60000023Steering Cover Vac-Form39000047
Push button Switch60000059Top Flash Vac-Form45000170
4ft Fluorescent Tube64000014Top Flash Acrylic30000029
12v 2.2w Wedge Lamp64000002Cabinet Side Decal (Left)40000037
M16 Adjustable Foot88300079Cabinet Side Decal (Right)40000038
75mm Castor59000005Play Panel Instruction Decal40000043

Seat - Back Decal 40000035

Seat - Ridge Racer Decal 40000042

Seat - Namco Decal 40000036

Top Flash System 22 (Left) Decal 40000039

Top Flash System 22 (Right) Decal 40000040

Page 21
  • SCHEMATIC
Page 22

ae te ae Teceping acey! PGEAR a STEERING Assy | SEA! ae 2 lie

et pe " sis rai fos — fs; a= — | ——F | Sy eran iz er ————————

:aeseata:

ame 21 cand RIGHT PLAYER

~ oo Tl TTL 4

revel ara] : Ll csmer

:“flew ©:

| (hess fe

PINK/RED.tH
2Eires— ibe.fH

ravi HEE be a oo

CREDIT DISPENSE enya. BOARD

= bn F