CATHODE RAY TOMES

Rolling Thunder TM-300 1st Printing

Rolling Thunder (rev 3) (Namco, 1986) · Technical Manual · 48 pages · 54 sections · original scan

Page 1

ZZ ryu U/@“j LA;

Operators Manual

Page 2

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 3

SANIT [I TWN WH SLSELN ISP HUNDER

Operators Manual

with Illustrated Parts Lists

Zi L772 LAA LAA tizzzwigl, LAA LAA ZZ SZ \ LZ LL

Page 4

© 1987 by Atari Games Corporation All rights reserved No part of this publication may be reproduced by any mechanical, photographic, or electronic process, or in the form of a phonographic recording, nor may it be stored ina retrieval system, transmitted, or otherwise copied for public or private use, without permission from the publisher. The game play, all graphic designs, this technical manual, its accompanying schematic diagrams, and the display manual are protected by the U.S. Copyright Act of 1976. This Act provides for increased penalties for violating federal copyright laws. Courts can impound infringing articles while legal action is pending. If infringers are convicted, courts can order destruction of the infringing articles. In addition, the Act provides for payment of statutory damages of up to $250,000 in certain cases. Infringers may also have to pay costs and attorneys’ fees and face an imprisonment of up to five years.

Atari Games Corporation will aggressively enforce its copyrights against any infringers. We will use all legal means to immediately halt any manufacture, distribution, or operation of a copy of video games made by us. Anyone who purchases such copies risks forfeiting such a game.

Published by: Atari Games Corporation 675 Sycamore Drive P.O. Box 361110 Milpitas, California 95035

Printed in the U.S.A. 2R Rolling Thunder

Page 5

Rolling Thunder

Notice Regarding Non-ATARI® Parts

A WARNING A

Use of non-ATARI parts or modifications of any ATARI game circuitry may adversely affect the safety of your game, and may cause injury to you and your players.

You may void the game warranty (printed on the inside back cover of this manual) if you do any of the following: © Substitute non-ATARI parts in the game.

  • Modify or alter any circuits in the game by using kits or parts not supplied by Atari Games Corporation.

NOTE

This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual, may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of Federal Communications Commission (FCC) Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area or modification to this equipment is likely to cause interference in which case the user, at his own expense, will be required to take whatever measures may be required to correct the interference. If you suspect interference from an ATARI® game at your location, check the following: ¢ All ground wires in the game are properly connected as shown in the game wiring diagram. © The power cord is properly plugged into a grounded three-wire outlet

  • On games provided with an Electromagnetic Interference (EMI) ground plane, be sure the game printed-circuit boards (PCBs) are properly installed on the EMI Ground Plane. If you are still unable to solve the interference problem, please contact Customer Service at Atari Games Corporation. See the inside front cover of this manual for service in your area.

iii

Page 6

Table of Contents

Set-Up How to Use This Manual ............. Inspecting the Game OOo ae Control and Switch Locations ......

Game Play ae Pre PE O42 ORG OF

Self-Test Explanation of the Self-Test Screen. . . Service Switch ..................005

Maintenance Preventive Maintenance ..... Preventive Maintenance Intervals . Removing the Control Panel . Cleaning the Push-Button Leaf Switches Cleaning the Coin Mechanism .... . Cleaning the Interior Components Joystick Control ................

Corrective Maintenance . Removing the Game PCB... Removing the Video Display . . Replacing the Video Display . Removing the Speaker ....

Illustrated Parts Lists See List of Illustrations that follows. Se S

2-2 Rolling Thunder

Page 7

Rolling Thunder

List of Illustrations

Figure 1-1

Figure 2-1

Figure 3-1 Figure 3-2 Figure 3-3

Figure 4-1 Figure 4-2 Figure 4-3 Figure 4-4 Figure 4-5 Figure 4-6 Figure 4-7

Table 1-1 Table 1-2 Table 1-3 Table 2-1 Table 2-2 Table 3-1 Control and Switch Locations ... 2.2.6. ...6. 0522s

Self-Test Screen. ........-..

Leaf Switch and Joystick Removal ...... Joystick Lubrication . . Control Panel, Video Display, and Speaker Removal

Cabinet-Mounted Assemblies ... 22.6.2... 05s e sees Control Panel Assembly eo Be eon cd] BE Joystick Assembly ...........+- Ape Switching/Linear (SL) Power Supply Assembly Bag Coin Acceptors, Inc. Coin Door Assembly... .. . . Rolling Thunder Game PCB and Sub PCB Assemblies . . Rolling Thunder End PCB Assembly .

List of Tables

Game Specifications ...... 6.6.66. eee eee eee DIP Switch A Option Settings . . DIP Switch B Option Settings ....... DIP Switch A Option Settings ...............- DIP Switch B Option Settings .........-..-. Recommended Preventive Maintenance Intervals | banee

Page 8

vi

Safety Summary

The following safety precautions apply to all game operators and service personnel. Specific warnings and cautions will be found throughout this manual where they apply. & WARNING A Properly Ground the Game. Players may receive an electrical shock if this game is not properly grounded! To avoid electrical shock, do not plug in the game until it has been inspected and properly grounded. This game should only be plugged into a grounded three-wire outlet. If you have only a 2-wire outlet, we recommend you hire a licensed electrician to install a grounded outlet. Players may receive an electrical shock if the control panel is not properly grounded! After servicing any parts on the control panel, check that the grounding wire is firmly secured to the inside of the control panel. Only then should you lock up the game. AC Power Connection. Before connecting the game to the AC power source, verify that the game’s power supply is properly configured for the line voltage in your location. Disconnect Power During Repairs. To avoid electrical shock, disconnect the game from the AC power source before removing or repairing any part of the game. When removing or repairing the video display, extra precautions must be taken to avoid electical shock because high voltages may exist within the display circuitry and cathode-ray tube (CRT) even after power has been disconnected. Do not touch internal parts of the display with your hands or with metal objects! Always discharge the high voltage from the CRT before servicing this area of the game. To discharge the CRT: Attach one end of a large, well-insulated, 18-gauge jumper wire to ground. Momentarily touch the free end of the grounded jumper to the CRT anode by sliding it under the anode cap. Wait: two minutes and discharge the anode again. Use Only ATARI Parts. To maintain the safety integrity of your ATARI game, do not use non- ATARI parts when repairing the game. Use of non-ATARI parts or other modifications to the game circuitry may adversely affect the safety of your game, and injure you or your players. Handle the CRT With Care. If you drop the CRT and it breaks, it may implode! Shattered glass can fly six feet or more from the implosion. Use the Proper Fuses. To avoid electrical shock, use replacement fuses which are specified in the parts list for this game. Replacement fuses must match those replaced in fuse type, voltage rating, and current rating. In addition, the fuse cover must be in place during game operation.

CAUTION Properly Attach All Connectors. Make sure that the connectors on each printed-circuit board (PCB) are properly plugged in. Note that they are keyed to fit only one way. If they do not slip on easily, do not force them, A reversed connector may damage your game and void the warranty. Ensure the Proper AC Line Frequency. Video games manufactured for operation on 60 Hz, line power (i.¢., United States) must not be operated in countries with 50 Hz line power (i.¢., Europe) The fluorescent light ballast transformer will overheat, causing a potential fire hazard if 60 Hz games are operated on power lines using 50 Hz. Check the product identification label of your game for the line frequency required. ABOUT NOTES, CAUTIONS, AND WARNINGS In all Atari publications, notes, cautions, and warnings have the following meaning:
NOTE—A highlighted piece of information.
CAUTION—Equipment and/or parts can be damaged or destroyed if instructions are not followed You will void the warranty on Atari printed-circuit boards, parts thereon, and video displays if equipment or parts are damaged or destroyed due to failure of following instructions.
WARNING—Players and/or technicians can be injured or killed if instructions are not followed. (The word WARNING is always surrounded by international warning symbols—triangles with exclamation marks inside of them.) Rolling Thunder
Page 9

Chapter 1

Set-Up

How to Use This Manual

This manual is written for game operators and service

technicians, and provides information for setting up, playing, testing, and maintaining your Rolling Thunder* game. The manual is divided into the following chapters: © Chapter 1 contains set-up and game play information. © Chapter 2 contains self-test procedures. © Chapter 3 contains preventive and corrective maintenance procedures. © Chapter 4 contains illustrated parts lists. Schematic diagrams for the Rolling Thunder game circuitry are contained in the Schematic Package Supplement (SP-300) included with your game. This chapter includes information required to set up and play your Rolling Thunder game. Carefully read this information before applying power to the game.

A WARNING A

To avoid electrical shock, do not plug in the cabinet until it has been properly inspected and set up for the line voltage in your area. This cabinet should only be connected to a grounded three-wire outlet. If you have only a two-wire outlet, we recommend you hire a licensed electrician to install a grounded outlet. Players can receive an electrical shock if the game is not properly grounded. Do not touch internal parts of the display with your hands or with metal objects.

*Rolling Thunder is engineered and designed by Namco Ltd. Manufactured by Atari Games. Trademark and © Namco 1986.

Page 10

Set-Up

Inspecting the Game

CAUTION Do not plug in the game until you have completed the following inspection steps.

Please inspect your Rolling Thunder game carefully to ensure that the game is complete and delivered to you in good condition. Figure 4-1 shows the locations of the component parts of the game. Table 1-1 lists space, power, and environmental requirements.

  • Examine the exterior of the cabinet and the control panel for dents, chips, or broken parts.
  • Use a Phillips screwdriver to remove the screws holding the rear access panel to the cabinet. Unlock and remove the panel. Unlock and open both coin doors. Inspect the interior of the cabinet as follows:

a. Ensure that all plug-in connectors (on the cabinet harnesses) are firmly plugged in. Do not force connectors together. The connectors are keyed so they only fit in the proper orientation. b. Ensure that all plug-in integrated circuits on each PCB are firmly plugged into their sockets. c. Inspect the power cord for any cuts or dents in the insulation.

d. Inspect the power supply. Make sure that the correct fuses are installed. Check that the harness is plugged in correctly and that the fuse-block cover is mounted in place. Check that the green ground wire is connected.

e. Inspect other major subassemblies, such as the video display, printed-circuit boards (PCBs), control, and speaker. Make sure that they are mounted securely and that the green ground wires are connected.

Table 1-1 Game Specifications

Characteristic Specification

Power Consumption 175 V-A, 125 W RMS maximum. Temperature +5° to +38° C(+37° to + 100° F) Humidity Not to exceed 95% relative Line Voltage 102 to 132 VAC (U.S. games) 198 to 264 VAC (Irish games) Width 25% in. (64 cm) Depth 33% in. (85 cm) Height 65% in. (166 cm) Weight 250 Ibs. (113 kg)

1-2 Rolling Thunder

f. Make sure that the game power source and operating environment is within the limits specified in Table 1-1, Game Specifications.

Control and Switch Locations

The following control and switch descriptions are for the Rolling Thunder game. Refer to Figure 1-1 for the locations of the controls and switches.

Power On/Off Switch The power on/off switch is located at the bottom rear of the cabinet. (See Figure 4-1.)

Volume Control The volume control is located in the upper right-hand corner of the Game PCB. The PCB is attached to the lower right-side panel of the cabinet. The volume control adjusts the level of sound produced by the game.

Coin Counter The coin counter is located on the shelf behind the upper coin door. The coin counter records the number of coins deposited.

Self-Test Switch The self-test switch is located on the End PCB, connected to the front of the Game PCB. Both PCBs are attached to the lower right-side panel of the cabinet. The self-test switch selects the Self-Test Mode to check game operation. Refer to Chapter 2 for a complete description of selftest operation.

Service Switch The service switch (a two-pin header connection) is located on the End PCB, connected to the front of the Game PCB. Both PCBs are located on the inside lower right-side panel of the cabinet. This switch has two functions, depending on whether the game is in the Self-Test Mode:

  • The switch is used as a coin switch when the game is not in the Self-Test Mode. Squeezing the two connector pins together gives the game one credit.
  • In the Self-Test Mode, the switch is used to make adjustments to the video display. A cross-hatch pattern appears on the display when the switch is turned on Squeezing the two connector pins together displays the pattern. Squeezing the pins a second time brings back the Self-Test screen. (Refer to the video display service manual included with your game for further information.)

a

Page 11

Rolling Thunder

Volume Control

Game woot Act y i o

f f

( Set-Up

Self-Test Switch

Service Switch S

End PCB

DIP Switch A

DIP Switch B

Figure 1-1 Control and Switch Locations

Setting the Coin and Game Option Settings

The Rolling Thunder cabinet has two dual-inline-package (DIP) option switches located on the Game PCB. (See Figure 1-1.)

  • Switch A is at location P1/2. Slide switches 2, 3, 7, and 8 on Switch A are for selecting coin options.
  • Switch B is at location P2/3. All slide switches except 6 and 7 on Switch B are for selecting game options. (Slide switches 6 and 7 are used to select the cabinet type setting.)
NOTE Slide switch 5 on Switch A is for factory use only and should always be turned off. Set the coin and credit option settings, and the game option settings by changing the settings of the DIP switches. Refer to Table 1-2 and Table 1-3 for the available options and default (recommended) settings. To change the coin and credit settings, and the game settings, use a pen or a sharp-pointed instrument to slide the appropriate small buttons to different settings. Right is the on position, and left is the off position. The joystick control and the push buttons are not used to change these settings. Refer to Chapter 2, Self-Test, for a more detailed description and explanation of the option settings.

Game Play

This section of the manual describes the theme of the Rolling Thunder game, the operating modes, and the game play features.

Page 12

Set-Up

Introduction

Rolling Thunder is a one- or two-player (alternating) game where the player controls the hero whose code name is Albatross. The story takes place in 1960 in New York City where the elusive Maboo, leader of the secret society Geldra, is plotting to conquer the world. Rolling Thunder is the undercover arm of a secret police organization. Their female agent, Leila, was sent on special assignment into Geldra’s underground headquarters Her mission was to expose the treacherous conspiracy, but she was captured.

Agent Albatross is the only man on the Rolling Thunder force who can possibly save Leila and complete the mission.

Operating Modes

Rolling Thunder has four operating modes: Attract, Play, High Score, and Self-Test. Rolling Thunder

Game Play

Game play starts with the player at the base of the enemy headquarters. Using a four-position joystick and Jump and Shoot buttons, the player makes way to the end of each area by evading or destroying enemy guards. The screen scrolls horizontally along with player maneuvers. By using the Shoot button, the player activates his weapon. Limited ammunition is given to the player at the start of each area, and he must collect additional ammunition by entering doors marked Bullets. If the player enters a door marked Arms, he receives a more powerful machine gun. By using the Jump button, the piayer can strategically evade or set up enemy attacks. The game playfields consist of various areas including old buildings, warehouses, and caves. To complete each area, the player must reach the exit. However, a timer and a life gauge limit the player in each area. Upon successful completion of each area, the screen briefly changes to show Maboo at his control station, as he awaits Albatross about to penetrate his headquarters. As the game progresses, the player is awarded bonus lives at several score thresholds.

Page 13

Rolling Thunder Set-Up

Table 1-2 DIP Switch A Option Settings

Settings of Switch A on Rolling Thunder Game PCB (at P1/2) 1 z 3 4 5 6 7 8 Option

Off Off Off On On Off On On

Off On

Off On

Off On

Off = Off Off On On Off On On

Off On Coins Per Credit (Right Mechanism) 1 Coin 1 Credit <4 1 Coin 2 Credits 1 Coin 5 Credits # 1 Coin 6 Credits

Screen Hold Normal <4 Hold

For Factory Use Only

Always in Off Position

Never in On Position Attract Sound Sound <4 No Sound

Coins Per Credit (Left Mechanism) 1 Coin 1 Credit <4 1 Coin 3 Credits -wo 2 Coins 1 Credit 3 Coins 1 Credit

Self-Test Normal (Attract Mode) <4 Self-Test Mode

Table 1-3 DIP Switch B Option Settings

Settings of Switch B on Rolling Thunder Game PCB (at P2/3) 1 2 3 4 5 6 7 8 Option

Off On

Off = Off Off On On On

Off On

Off On

Off On

Off On

Off On Game Continuation 6 Games Maximum <4 3 Games Maximum

Cabinet Type Type A (Upright) <4 ‘Type B (Cocktail—no flip) Type C (Cocktail—flip) Select Level No Yes <4

Game Difficulty Normal <4 Easy Timer Value 120 Seconds <4 150 Seconds

Bonus Lives Granted at: 70,000 Points and 200,000 Points <4 100,000 Points and 300,000 Points

Number of Starting Lives

bY

<4 Manufacturer's recommended settings + Recommended settings for Germany -w Recommended settings for United Kingdom

Page 14

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 15

Chapter 2

Self-Test

The Rolling Thunder* game tests itself and provides visual and audible indications of the condition of the game circuitry. Self-test information is visually displayed on the screen and audibly presented through the sound system. No additional equipment is required. We suggest that you perform a self-test when you first set up the game, each time you collect the money, or when you suspect game failure. Coin and game options are selected in the Self-Test Mode.

When the self-test switch is turned on, the game enters the Self-Test Mode. Turning the self-test switch off at any time during the Self-Test Mode causes the game to return to the Attract Mode.

“Rolling Thunder is engineered and designed by Namco Ltd. Manufactured by Atari Games. Trademark and © Namco 1986.

Page 16

Self-Test

Self-Test Screen

The Self-Test screen displays the game Main and Sub ROM condition, coin and credit options, game options, dualinline-package (DIP) switch settings, and other game conditions. After turning on the self-test switch, the Self-Test screen shown in Figure 2-1 is displayed. The self-test switch is located on the End Printed-Circuit Board (PCB), connected to the front of the Game PCB. Both PCBs are attached to the inside lower right-side panel of the cabinet. (See Figure 1-1.)

DIP Switch Settings

The Rolling Thunder game has two DIP option switches located on the Game PCB. (See Figure 1-1.) The DIP Switch settings indicate the current settings of both DIP Switch A and DIP Switch B.

  • Switch A is at location P1/2. Slide switches 2, 3, 7, and 8 on Switch A are for selecting coin options. Switch B is at location P2/3. All slide switches except 6 and 7 on Switch Bare for selecting game options. (Slide switches 6 and 7 are used to select the cabinet type setting.)
NOTE Slide switch 5 on Switch A is for factory use only and should always be turned off.

One row of numbers refers to switches 1 through 8 on Switch A; the second row of numbers refers to switches 1 through 8 on Switch B. / denotes that the switch is turned on; 0 denotes that it is turned off. The settings are displayed on the screen as:

MAIN ROM OK SUB ROM OK RAM OK CUSTOM OK COIN1 1 COIN. 1 CREDIT COIN2 1 COIN. 1 CREDIT

ATTRACT SOUND

ALBATROSS 3 BONUS 70000/200000 PTS TIMER 120 SEC

DIFFICULTY NORMAL

CABINET TYPE A CONTINUATION 6 SELECT YES SOUND PSG Oo DIPSWA 10000000 DIPSWB 00000000

Figure 2-1 Self-Test Screen

2-2 Rolling Thunder

DIPSWA 10000000 DIP SWB 00000000 Set the coin and credit option settings, and the game option settings by changing the settings of the DIP switches. Refer to Table 2-1 and Table 2-2 for the available options and default (recommended) settings. To change the coin and credit settings, and the game settings, use a pen or a sharp-pointed instrument to slide the appropriate small buttons to different settings. Right is the on position, and left is the off position. The joystick control and the push buttons are mor used to change these settings.

Main ROM/Sub ROM Test The Main ROM/Sub ROM Test indicates the condition of the game Main ROM and the Sub ROM circuitry, and is displayed on the screen as: MAIN ROM OK SUB ROM OK This message indicates that both the Main ROM and the Sub ROM are normal. If either ROM fails, the message BAD, and not OK, is displayed. MAIN ROM refers to ROM on the Game PCB. SUB ROM refers to ROM on the Sub PCB, or the “‘piggyback”’ PCB.

RAM/Custom IC Test The RAM/Custom IC Test indicates the condition of the game RAM and the custom integrated circuits (ICs), and is displayed on the screen as: RAM OK CUSTOM OK This message indicates that both the RAM and the custom ICs are normal. If either the RAM or any of the custom ICs fail, the message BAD is displayed.

Coin and Credit Options

The current coin and credit option settings are displayed on the screen as: COINI 1 COIN 1 CREDIT

COIN2 1 COIN 1 CREDIT These are the default (recommended) settings for coin mechanisms 1 (left) and 2 (right). The coin and credit options can be changed by resetting the DIP switches located on the Game PCB. The COIN/ setting can be changed by resetting slide switches 2 and 3 on Switch A to the On position. The COIN2 setting can be changed by resetting slide switches 7 and 8 on Switch A to the On position. (Refer to D/P Switch Settings earlier in this chapter for more information.).

Attract Mode Sound Setting

The Attract Mode Sound setting indicates that sound is selected when the game is in the attract mode. This setting is displayed on the screen as:

Page 17

Rolling Thunder

ATTRACT SOUND The sound can be turned off in the attract mode by resetting slide switch 4 on DIP Switch A to the On position

Starting Lives Setting

The Starting Lives setting indicates the number of lives granted when game play begins, and is displayed on the screen as:

ALBATROSS 3 3 lives is the default (recommended) setting. The setting can be changed to 5 lives by resetting slide switch 1 on DIP Switch B to the On setting. Note that in the game play mode, the screen displays the words MAN x for the remaining number of men (lives).

Bonus Lives Setting

The Bonus Lives setting indicates when bonus lives are granted, and is displayed on the screen as: BONUS — 70,000/200,000 PTS 70,000 and 200,000 points is the default (recommended) setting for bonus lives. The setting can be changed to 100,000 and 300,000 points by resetting slide switch 2 on DIP Switch B to the On position.

Timer Value Setting

The Timer Value setting indicates the amount of game play time in seconds, and is displayed on the screen as: TIMER 120 SEC 120 seconds is the default (recommended) setting. The setting can be changed to 150 seconds by resetting slide switch 3 on DIP Switch B to the On position,

Game Difficulty Setting

The Game Difficulty setting indicates the difficulty level

of the game, and is displayed on the screen as:

DIFFICULTY NORMAL Normal is the default (recommended) setting. The setting can be changed to the easy level by resetting slide switch 4 on DIP switch B to the On position.

Cabinet Type Setting The Cabinet Type setting indicates whether the screen should alternately flip 180 degrees between two players. This setting is displayed on the screen as: CABINET TYPE A Leave slide switches 6 and 7 on DIP Switch B at the Off setting. Self-Test

Game Continuation Setting The Game Continuation setting indicates the maximum number of credits allowed for game continuation. This setting is displayed on the screen as: CONTINUATION 6 6 credits maximum is the default (recommended) setting. The setting can be changed to 3 credits maximum by resetting slide switch 8 on DIP Switch B to the On position.

Select Level Setting The Select Level Setting indicates whether or not the Select Level function is activated. This setting is displayed on the screen as:

SELECT YES If set to Yes, players can choose a starting level from Areas 1 through 5. (The player selects the starting level by holding down the 1-player start button, and moving the joystick to select any of the first five areas or levels.) If set to No, the game automatically starts at Story 1, Area 1,

Sound Test The Sound Test indicates the condition of the sound-effects circuitry (when sound is selected in the Attract Mode setting). This test is displayed on the screen as: SOUND PSG 0 Different sound numbers can be selected. The number is selected by moving the joystick to the right (increments the number) or to the left (decrements the number). Moving the joystick front (toward the display screen) or back selects PSG, FM, or VOICE. PSG indicates sound effect, and FM indicates music.

Service Switch The service switch (a two-pin header connector) is located on the End PCB, connected to the front of the Game PCB. Both PCBs are located on the inside lower right-side panel of the cabinet. This switch has two functions, depending on whether the game is in the Self-Test Mode:

  • The switch is used as a coin switch when the game is not in the Self-Test Mode. Squeezing the two connector pins together gives the game one credit.
  • In the Self-Test Mode, the switch is used to make adjustments to the video display. A cross-hatch pattern. appears on the display when the switch is turned on. Squeezing the two connector pins together displays the pattern. Squeezing the pins a second time brings back the Self-Test screen. (Refer to the video display service manual included with your game for further information.)

2-3

Page 18

Self-Test Rolling Thunder

Table 2-1 DIP Switch A Option Settings

Settings of Switch A on Rolling Thunder Game PCB (at P1/2) 1 2 3 4 5 6 7 Option

Off Off On On

Off On

Off On

Off On

Off Off Off On On Off On On

Off On Off On Off On Coins Per Credit (Right Mechanism) 1 Coin 1 Credit < 1 Coin 2 Credits 1 Coin 5 Credits # 1 Coin 6 Credits

Screen Hold Normal <4 Hold

For Factory Use Only Always in Off Position <4 Never in On Position

Attract Sound Sound <4 No Sound.

Coins Per Credit (Left Mechanism) 1 Coin 1 Credit <4 1 Coin 3 Credits m0 2 Coins 1 Credit 3 Coins 1 Credit

Self-Test Normal (Attract Mode) <4 Self-Test Mode

Table 2-2 DIP Switch B Option Settings

Settings of Switch B on Rolling Thunder Game PCB (at P2/3) 1 2 3 4 5 6 7 Option

Off Off Off On On On

Off On

Off On

Off On

Off On

Off On Off On Game Continuation 6 Games Maximum <4 3 Games Maximum

Cabinet Type Type A (Upright) Type B (Cocktail—no flip) Type C (Cocktail—flip) Select Level No Yes <4

Game Difficulty Normal <4 Easy Timer Value : 120 Seconds 4 150 Seconds

Bonus Lives Granted at: 70,000 Points and 200,000 Points <4 100,000 Points and 300,000 Points Number of Starting Lives

<4 Manufacturer's recommended settings + Recommended settings for Germany -m Recommended settings for United Kingdom

Page 19

Chapter 3

Maintenance

This chapter includes preventive and corrective mainte nance procedures for the Rolling Thunder game components that are subject to the most use. To assure maximum trouble-free operation from this game, we recommend that preventive maintenance be performed as described in this chapter. Removal and replacement procedures are provided for components that might require corrective maintenance Chapter 4, Illustrated Parts Lists, also be used to locate the parts of this game that are mentioned, but not illustrated, in the maintenance procedures,

Page 20

Maintenance Rolling Thunder

Preventive Maintenance

Preventive maintenance includes cleaning, lubricating, and tightening hardware. How often preventive maintenance is performed depends upon the game environment and frequency of play. However, for those components listed in Table 3-1 Preventive-Maintenance Intervals, we recommend that preventive maintenance be performed at the intervals specified.

Preventive-Maintenance Intervals

The preventive-maintenance intervals specified in Table 3-1 are the recommended minimum requirements for the components listed.

A WARNING A

To avoid possible electrical shock, turn off the game before performing any maintenance procedures.

Removing the Control Panel

Perform the following procedure to remove/replace the control panel. (See Figure 3-3.)

  • Unlock and open the upper coin door.
  • Carefully reach up through the upper coin door opening and release the two spring draw latches located under the control panel on each side of the cabinet.
  • Grasp the control panel on the top edge (next to the speaker grille) and gently tilt the panel up slightly. Remove the panel from the front edge of the cabinet. Stand the control panel on its back edge by placing it in the wood slots located under the control panel on each side of the cabinet. The panel is now in position for servicing the leaf switches or the joystick control.
  • If you need to remove the control panel, disconnect the control harness connector from the Game PCB and disconnect the green ground wire.

Table 3-1 Recommended Preventive- Maintenance Intervals

Joystick Control Lubricate and tighten hardware at least every three months. Coin Mechanism Inspect whenever you collect coins. Clean at least every three months.

  • Carefully lift the control panel from the cabinet.
  • Replace the control panel in the reverse order of removal.

Cleaning the Push-Button Leaf

Switches

Perform the following procedure to clean the push-button leaf switch contacts and tighten the securing hardware. (See Figure 3-1.)

  • Follow the procedure described in steps 1-3 above for removing the control panel.
  • Use electrical contact cleaner to clean the contacts. Do not burnish them. When the push button is pressed, the wiping action of the cross-bar contacts provides a self-cleaning feature.
  • Using a '%,-inch open-end wrench, tighten the stamped nut securing the push-button leaf switch to the control panel

Cleaning the Coin Mechanism Use a soft-bristled brush to remove loose dust or foreign material from the coin mechanism. A toothbrush can be used to remove any stubborn build-up of residue in the coin path. After cleaning the coin mechanism, blow out all of the dust with compressed air.

Cleaning the Interior Components Perform the following procedure to clean the components inside the cabinet.

Turn off the game power, but do not unplug the power cord before cleaning inside the cabinet. The power cord provides a ground path for stray static voltages that might be present on the cleaning tools.

  • Unlock and remove the rear access panel.
  • Use a vacuum cleaner with a soft long-bristled brush attachment or a soft-bristled paint brush to remove loose dirt and dust accumulated on the inside of the cabinet. Be sure to clean the electrical components thoroughly (power supplies, PCB assemblies, display, etc.).
Page 21

Rolling Thunder

1-Inch-Long Carriage Bolt

Button Assy

Harness Assy Leaf Switch with Button Holder Maintenance

Red Button Assy Yellow Button Assy

Lock Nut

Joystick Assembly Stamped Nut

Figure 3-1 Leaf Switch and Joystick Removal

CAUTION Be extremely careful when cleaning the electrical components inside the cabinet. Avoid touching the electrical components with any solid object other than the soft bristles of the vacuum attachment or paint brush.

Joystick Control

Preventive maintenance on the joystick control consists of inspecting the pivot and actuator balls for excessive wear or dirt, lubricating the pivot ball, adjusting the leaf switches and, if necessary, replacing or tightening the securing hardware.

Lubricating the Joystick Control

Perform the following procedure to lubricate and tighten the joystick control. (See Figure 3-2.)

  • Remove the control panel as previously described.
  • Apply a light film of Lithium grease (Atari part no. 107027-001) to the lubrication points shown in Figure 3-2.
  • Using a %-inch wrench, tighten the four nuts holding the joystick to the control panel
  • Using a %-inch wrench (or an appropriate tool), tighten the four screws holding the positioning plate to the lower housing.
Page 22

Maintenance Rolling Thunder

Corrective Maintenance

Upper Housing Assembly

Leaf Switch

#4-20 Screw

#8-16 Screw

Figure 3-2 Joystick Lubrication

3-4 Corrective maintenance consists of removing, disassembling, reassembling, and replacing the push-button leaf switches, joystick control, game printed circuit board (PCB), video display, and speaker. The procedures for removing and replacing the Game PCB, video display, and the speaker follow.

Removing the Game PCB

Perform the following procedure to remove/replace the Game PCB.

  • Turn the game power off.
  • Remove the rear access panel of the cabinet.
  • Remove the mounting screw and the fiber washer from the upper right-hand corner of the Game PCB. 4, Grasp the back edge of the Game PCB and gently slide it straight backwards until it just clears the rear slotted guide.
  • Replace the Game PCB in the reverse order of removal.

Removing the Video Display

Perform the following procedure to remove/replace the video display. (See Figure 3-3.)

  • Turn the game power off and wait two minutes. Unplug the power cord.
  • Remove the control panel as described under Preventive Maintenance.
  • Using a Phillips screwdriver, remove the four screws holding the speaker grille to the cabinet. 4, Remove the video display shield. . Remove the bezel.
  • Using a Phillips screwdriver, remove the four screws holding the rear access panel to the cabinet. Ww

A WARNING A

High Voltage The video display contains lethal high voltages. To avoid injury, do not attempt to service this display until you observe all precautions necessary for working on high-voltage equipment. X-Radiation The video display has been designed to minimize X-radiation. However, to avoid possible exposure to soft X-radiation, never modify the highvoltage circuitry. Implosion Hazard The cathode-ray tube may implode if struck or dropped. Shattered glass may cause injury within a 6-foot radius. Use care when handling the display.

Page 23

Rolling Thunder Maintenance

Video Display Shield

Video Display

Video Display Bezel

Grille Mounting Screws (4 Places)

Speaker Grille

Speaker Mounting Screws (4 Places)

Control Panel

Figure 3-3 Control Panel, Video Display, and Speaker Removal

  • Discharge the high voltage from the cathode-ray tube A WARNING A (CRT) before proceeding. The display assembly contains a circuit for discharging the high voltage to ground when power is removed. However, to make certain, always discharge the display as follows. To avoid dropping the video display, use extreme care when removing the display from the cabinet. We recommend that a second person carefully hold the display chassis from the back a. Attach one end ofa large, well-insulated, 18-gauge of the cabinet while the other person lifts it from jumper wire to ground. the front of the cabinet. b. Momentarily touch the free end of the grounded jumper to the CRT anode by sliding it under the anode cap. 9. Using a %<-inch wrench, reach through the control panel opening and remove the four nuts and washers c, Wait two minutes and repeat part b. holding the video display to the cabinet shelf.
  • From the back of the cabinet, unplug the display har- 10. Push the four carriage bolts up from the bottom of ness connectors from the display. the shelf and remove them from the back of the cabinet
  • Carefully slide the display out through the front of the cabinet.
  • Replace the video display as described in the following procedure.

3-5

Page 24

Maintenance

NOTE Whenever the cathode-ray tube and yoke are replaced as a single unit, readjust the brightness, size, and centering as described in the display manual. Check the purity and convergence also according to the display manual instructions, but adjust both only if required.

Replacing the Video Display

Perform the following procedure to replace the video display in the cabinet. (See Figure 3-3.)

  • Gently lift the video display through the front of the cabinet and onto the shelf.
  • Position the display so that the four slots in the chassis are aligned with the corresponding mounting holes in the cabinet shelf.
  • From the back of the cabinet, insert the four carriage bolts into the four slots in the chassis and through the mounting holes in the shelf.
  • From the back of the cabinet, slide the display back until the rear of the CRT frame fits against the wood cleat at the rear of the shelf.
  • From the back of the cabinet, push the four carriage bolts through the CRT frame and shelf. Through the control panel opening, tighten the four mounting nuts and washers under the shelf using a /,-inch wrench.

3-6 Rolling Thunder

  • Connect the display harness to the display PCB.
  • Replace the bezel.
  • Replace the video display shield.
  • Using a Phillips screwdriver, securely tighten the four screws holding the speaker grille to the cabinet:

Removing the Speaker

Perform the following procedure to remove/replace the speaker. (See Figure 3-3.)

  • Using a Phillips screwdriver, remove the four screws on the front of the speaker grille.
  • Lift the speaker grille from the cabinet
CAUTION Do not touch the speaker cone when handling the speaker. The cone material is fragile and can be easily damaged.
  • Using a Phillips screwdriver, remove the four screws holding the speaker to the cabinet.
  • Remove the speaker just far enough to disconnect the two speaker wires.
  • With the tabs pointed outward, replace the speaker in the reverse order of removal.
Page 25

Illustrated Parts Lists

This chapter provides information you need to order parts for your game. Common hardware (screws, nuts, washers, etc.) has been deleted from most of the parts lists. —— > The PCB parts lists are arranged in alphabetical order by component. Each component subsection is arranged alphanumerically by reference designator. Other parts lists are arranged alphanumerically by Atari part number. In these parts lists, all A-prefix numbers come first. Following these are numbers in sequence evaluated up to the hyphen, namely 00- through 99-, then 000598- through approximately 201000-. ‘When ordering parts, please give the part number, part name, number of this manual, and serial number of your game. This will help us fill your order rapidly and correctly. We hope the results will be less downtime and more profit from your game. Atari Customer Service numbers are listed on the inside front cover of this manual.

Page 26

Illustrated Parts Lists Rolling Thunder

043596-01 043594-01 Video Display Bezel n39017-001 Tinted Display Shield, or Wells-Gardner Clear Display, or 044067-01 139017-204 Clear Display Shield Wells-Gardner Tinted Display

78-6900404 A044063-01 Foam Tape Graphics Panel Assy

044065-02 Right-Side Panel Decal

043595-01 Speaker Grille

“ 148007-104 Speaker

Joystick Assy See Figure 4-3

Control Panel Assy See Figure 4-2

178013-001 Spring Draw Latch

Coin Door Assy See Figure 4-5

171078-002 Coin Counter

A043424-01 038091-01 Locking Bar Assy (Optional) ———> Molded Coin Box

Figure 4-1 Cabinet-Mounted Assemblies A044060-01 A

4-2

Page 27

Rolling Thunder Illustrated Parts Lists

Items Not Shown

NOTE A044083-01 To comply with emission requirements, the Speaker Harness Assy Federal Communications Commission re- 034536-02 quires that the ground strap be secured to Vibration Damper both the Game PCB and End PCB Assemlies. Do not operate this game without properly installing the ground strap.

037332-01 Louvered Grille 044065-01

Left-Side Panel Decal

A044082-01 S Video Harness Assy = ==> SSS oe S A043377-01 Display Power Harmess Assy

End PCB Assy See Figure 4-7

A043086-05 Ground Strap Assy

YRS Y Ns) A044084-01 | A! YQ Coin Harness Assy Game PCB Assy See Figure 4-6

78-3201 Adjustable Glide

A044081-01 Power Supply Assy Power Harness Assy See Figure 4-4

< oS A044068-01 Cabinet Assy

043583-01 Rear Access Panel 042914-01 Ventil Soeacseat /entilation Grille On/Off Switch & Power Cord

Figure 4-1 Cabinet-Mounted Assemblies, Continued

Page 28

Illustrated Parts Lists Rolling Thunder

Cabinet-Mounted Assemblies Parts List

Part No. Description

A043055-01 A043086-05 A043377-01 A043424-01

A044063-01 A044068-01 A044081-01 A044082-01

A044083-01 A044084-01 78-3201 78-6900404

009992-01 034536-02 037332-01 038091-01

042914-01 043583-01 043595-01 043596-01

044065-01 044065-02 043594-01 044067-01

139017-001 139017-204 148007-104 71078-002 On/Off Switch Assembly with Harness Ground Strap Assembly Display Power Harness Assembly Locking Bar Assembly (optional—can be used with either brand of coin door)

Graphics Panel Assembly Cabinet Assembly Power Harness Assembly Video Harness Assembly

Speaker Harness Assembly Coin Harness Assembly Adjustable Glide %-Inch-Wide x Y-Inch-Thick Foam Tape (24 inches required; used on top underside lip of speaker grille)

On/Off Switch Cover 0.50-Inch-Thick Foam Vibration Damper Louvered Grille Molded Coin Box

Ventilation Grille Rear Access Panel with Lock Speaker Grille 19-Inch Video Display Bezel

Left-Side Panel Decal Right-Side Panel Decal Tinted Video Disp Clear Video Disp! shield; used with part no. 139017-001 OR Shield; used with part no. 139017-204

Wells-Gardner 19-Inch Clear Color Raster Video Display OR ‘Wells-Gardner 19-Inch Tinted Color Raster Video Display 4'4-Inch Round, 8Q, 10W, Shielded Speaker Non-Resettable Counter, 12 VDC 178013-001 Spring Draw Latch

The following items are technical information supplements for this game: T™M-300 Rolling Thunder Operators Manual TM-283 Wells-Gardner 19-Inch Color Raster Video Display Service Manual; used with part no. 139017-001 SP-300 Rolling Thunder Schematic Package Supplement ST-300 Rolling Thunder Self-Test Label 99-131014 Wells-Gardner 19-Inch Color Raster Video Display Service Manual; used with part no. 139017-204

4-4

Page 29

Rolling Thunder Illustrated Parts Lists

044066-01 036895-01 Control Panel Decal Bezel

178030-004 Red Button Assy 178030-007 75-5116B 1-Inch-Lang Carriage Bolt Yellow Button Assy

044062-01 Control Panet

62-041 Push-Button Switch /

\ &

3S

177010-240 Lock Nut

A044086-01 i Joystick Assembly Harness Assy 160013-002 See Figure 4-3 Leaf Switch with Button Holder 75-9910NO ‘Stamped Nut

Figure 4-2 Control Panel Assembly A044061-01 A

Control Panel Assembly Parts List

Part No. Description

A040934-01 4-Position Leaf Switch Joystick Assembly A044086-01 Control Panel Harness Assembly 62-041 Black Cap (No LED) SPDT Push-Button Switch 75-5116B #10-24 x 1,00-Inch-Long Black Carriage Bolt

75-9910NO #11 %Inch Stamped Nut 036895-01 Black Molded Bezel 044062-01 Control Panel 044066-01 Control Panel Decal 160013-002 Cross-Bar Leaf Switch with Button Holder 177010-240 #10-24 Lock Nut 178030-004 Red Button Assembly 178030-007 Yellow Button Assembly

Page 30

Illustrated Parts Lists Rolling Thunder

A040932-01 Upper Housing Assy

041287-01 Lower Housing

041508-01 Leaf Switch

176030-110 #4-20 Screw

039714-01 Actuator

039717-01 Plate

176002-140 #8-16 Screw

Figure 4-3 Joystick Assembly A040934-01 B

Page 31

Rolling Thunder Illustrated Parts Lists

Joystick Assembly Parts List

Part No. Description

A040932-01 Upper Housing Assembly 041287-01 Lower Housing 041508-01 Leaf Switch 039714-01 Actuator

039717-01 4-Position Positioner Plate 176002-140 #8-16 x 2,50-Inch-Long Self‘Tapping Hex Washer-Head Screw 176030-110 #4-20 x .62-Inch-Long Hex Washer-Head Self‘Tapping Screw

Page 32

Illustrated Parts Lists Rolling Thunder

4 WARNING A The switching power supply has high vottages on it when power is turned on. Therefore, be sure you do not touch this power supply unless you have turned off the power to the game. 149007-001 Astec 5V/12V Switching Power Supply A044089-01 A044090-01 5V Harness Assy AC Harness Assy 72-HA4616S, Screw

179231-002 Terminal Block

A043367-01 Jumper Assy Go 175004-706 Washer

(

A042384-01 Line Filter Assy

72-HA4608S Screw 72-HA4206S Screw

a 116024-500 AL ~500 Resistor A

142045-001 Transformer

037640-01 S if 46-2013002 | a 5 Warning Label SS Fuse e Z QA 043396-01 Power Supply Chassis Base 043908-01 Fuse Label

179225-2201 034544-01 Fuse Block 72-HA4806S, Fuse Block Cover Screw

Figure 4-4 Switching/Linear (SL) Power Supply Assembly A044074-01 A

Page 33

Rolling Thunder

Switching/Linear (SL) Power Supply Assembly Ilustrated Parts Lists

Parts List

Part No. Description

A042384-01 Line Filter Assembly A043367-01 Jumper Assembly A044089-01 5 V Harness Assembly A044090-01 AC Harness Assembly

46-2013002 250 V Slow-Blow 3 A Fuse 72-HA4206S #4-32 x %-Inch Cross-Recessed Pan-Head Thread-Forming Screw 72-HA4608S #6-32 x 's-Inch Cross-Recessed Pan-Head Thread-Forming Screw 72-HA4616S #6-32 x 1-Inch Cross-Recessed Pan-Head Thread-Forming Screw

72-HA4806S #8-32 x ¥-Inch Cross-Recessed Pan-Head Thread-Forming Screw 034544-01 Fuse Block Cover 037640-01 Power Supply Warning Label 043396-01 Power Supply Chassis Base

043908-01 Power Supply Fuse Label 116024-500 50, 5 W, Chassis-Mount, Wirewound Resistor 142045-001 ‘Transformer 149007-001 Astec 5 V/12 V Switching Power Supply

175004-706 #6 Fiber Washer 178181-6808 179225-2201 179231-002 171-Inch ID, ¥-Inch OD, Aluminum Standoff 1-Position Fuse Block 2-Position Terminal Block

Astec 5-Volt Power Supply Sub-Assembly Model SA40-1304 Parts List

DesignatorDescriptionPart No.

Capacitors

ci, C2Capacitor, Met Poly, .1 #E, + 20%, 250 VAC99-209076
C3, C4Capacitor, Poly, 2200 pF, + 20%, 250 VAC99-209077
csCapacitor, Met Poly, 2200 pF, + 20%, 250 V99-209080
C8Capacitor, Electrolytic, 220 uF, + 100 -+ 10%, 10 V99-209072
coCapacitor, Ceramic, 1000 pF, + 20%, 3 KV, Z5P99-209068
c10Capacitor, Met Poly, .022 pF, + 20%, 250 VAC99-209079
cllCapacitor, Poly, .22 pF + 10%, 100 V99-209014
cl2Capacitor, Electrolytic, 2200 wF, + 20%, 16 V, Sxa99-209073,
C13Capacitor, Poly, .01 wE, +5%, 50 V99-209075,
C14Capacitor, Electrolytic, 100 pF, + 20%, 25 V, Sxa99-209006
C15Capacitor, Electrolytic, 1000 uF, + 20%, 16 V, Sxa99-209008
C16Capacitor, Poly, .022 uF, + 20%, 50 V99-209078
ci7Capacitor, Electrolytic, 1000 uF, + 20%, 10 V, Sm99-209071
C18Capacitor, Ceramic, 330 pF, + 20%, 100 V, SI99-209069
C19Capacitor, Electrolytic, 470 uF, + 20%, 16 V, Sm99-209074
20Capacitor, Electrolytic, 100 wF, + 20%, 16 V, Sm99-209070
C21Capacitor, Poly, .22 uF, + 10%, 100 V99-209014
C23Capacitor, Ceramic, .01 uF, + 80-+ 20%, 100 V, ZSU99-209003

Diodes

DIDiode, RGP10A99-209083
D2Diode, RGP10J99-209033
Page 34

Illustrated Parts Lists Rolling Thunder

Astec 5-Volt Power Supply Sub-Assembly

Model SA40-1304 Parts List, Continued

Designator Description Part Ni

D3.Diode, GP10A99-209084
D4, DSDiode, RGP10J99-209033
D6, D7Diode, 1N460699-209030
D8Assembly, Regulator/SCR/Diode/Heat Sink99-209105
D8Diode, 12CTQ03599-209107
D9Diode, RGP10B99-209034
D10Assembly, Diode/Heat Sink99-209103
DuDiode, 1N460699-209030
D12, D13Diode, 1N400199-209035
DBIDiode, Bridge, KBPO899-209085

Inductors

13Inductor, 2.2 wH99-209029
14Inductor, 1.5 mH99-209028
LSAssembly, Inductor Coil99-209059
16Inductor, 4.4 wH99-209102

Transistors

Ql‘Transistor, NPN, 28C212099-209082
Q2Assembly, Transistor/Heat Sink99-209104
Q3Transistor, PNP, 2SB56199-209022

Resistors

RIResistor, Carbon Film, 470K 9, +5%, % W99-209089
R2Resistor, Wirewound, 332, +5%,3 W99-209097
R3, R4Resistor, Metal Oxide Film, 100K 2, +5%, 1 W99-209054
RSResistor, Carbon Film, 1K Q, +5%, 4 W99-209086
RGResistor, Metal Oxide Film, 1209, 45%, 2W99-209095
R7Resistor, Metal Film, 19, +5%, 1 W.99-209025
RBResistor, Carbon Film, 279, +5%, 4 W99-209040
ROResistor, Carbon Film, 682, +5%, 4 W99-209090
R1OResistor, Carbon Film, 109, +5%, % W99-209037
RILResistor, Carbon Film, 152, +5%, 4 W99-209087
R12Resistor, Metal Film, .75 9, 45%, 1 W99-209091
R13Resistor, Carbon Film, 5.62, +5%, % W.99-209046
R14Resistor, Carbon Film, 472, +5%, 4 W99-209043
R15, RIGResistor, Carbon Film, 2709, +5%, % W99-209041
RI7Resistor, Carbon Film, 8.22, +5%, 4 W99-209049
R18Resistor, Carbon Film, 3309, +5%, % W.99-209042
RI9Resistor, Carbon Film, 569, +5%, 4 W99-209045
R20Resistor, Carbon Film, 68 2, +5%, 4 W99-209090
R21Resistor, Carbon Film, 3309, +5%, 4 W.99-209042
R22Resistor, Carbon Film, 4709, +5%, 4 W.99-209044
R23Resistor, Metal Film, 8.2K Q, 41%, 4 W99-209094
R24Resistor, Metal Film, 2.7K Q, +1%, 4 W99-209093
R25,Resistor, Metal Film, 18K Q, +1%, %4 W99-209092
R27Resistor, Carbon Film, 22 9, +5%, 4 W99-209088
R28Resistor, Carbon Film, 109, 45%, 4 W99-209037
R29Resistor, Metal Oxide Film, 1209, +5%,2W99-209095

4-10

Page 35

Rolling Thunder Illustrated Parts Lists

Astec 5-Volt Power Supply Sub-Assembly

Model SA40-1304 Parts List, Continued

DesignatorDescriptionPart No.
R30Resistor, Wirewound, 150, +5%,5 W99-209096
R32Resistor, Carbon Film, 109, +5%, % W99-209037

Transformers

TlCom Mode Transformer Assembly99-209101
T2‘Transformer, Power, AC815499-209100
73Control Transformer Assembly (J/V)99-209058

Miscellaneous

FlFuse, 2 A, 250 V99-209081
ICRegulator, 43199-209023
1c2Assembly, Regulator/SCR/Diode/Heat Sink99-209105
1c2Regulator, UA791299-209106
SCRIAssembly, Regulator/SCR/Diode/Heat Sink99-209105
SCRIThyristor, SCR, 2N639599-209108
TMI, TM2Thermistor, 82, + 20%99-209099
VRIPotentiometer, Trimming, 1K 099-209098
ZIDiode, Zener, 5.6 V, +5%, 40 mA99-209031
Page 36

Illustrated Parts Lists Rolling Thunder

99-10140 Panel Assembly 75-948S Locknut va

99-10152 \ Right Coin Inlet ye 171006-035, Coin Mechanism 99-10116 Lever

99-10147 Harness

75-944S Locknut

99-10096 Fastener

99-10151 Left Coin Inlet

70-11-47 Lamp

99-10080 Lamp Socket

99-10105 ar 72-9406S Screw

99-10104 Bar Retainer

99-10042 thru 99-10045 AY

a Coin Switch Assembly

99-10150 Switch Cover 99-10154 Bracket Assembly

99-10153 Coin Return Box

99-10068 Coin Chute

65-441C Coin Switch

99-10075 thru 99-10078 Switch Wires 99-10008 Retainer 7544195

Screw

Figure 4-5 Coin Acceptors, Inc. Coin Door Assembly 171027-001 A

Page 37

Rolling Thunder Illustrated Parts Lists

99-10148 Lock Assembly

99-10142 Button Housing

72-HA1404C Screw

99-10134 panorae! 99-10119 Cover A Button Assembly ? Coin Door cs sane

> < 99-10115 99-10148 Spring Lock Assembly

S : - 99-10141 AY : c Coin Return Cover

cc) % A . A 99-10117 Coin Return Door

72-JA1405B Screw J——_99-10144 Channel Clip So 99-15066 Screw

99-10149 Service Door

038091-01 | L . . Coin Box \ be Cle S ; 99-10143, Frame

NOTE The acceptable substitute for this door (and the one used in games manufactured in Ireland) is the Coin Controls, Inc. Coin Door Assembly, part number 171034-001.

Figure 4-5 Coin Acceptors, Inc. Coin Door Assembly, Continued 171027-001 A

4-13

Page 38

Illustrated Parts Lists Rolling Thunder

Coin Acceptors, Inc. Coin Door Assembly Parts List

Part No. Description

65-441C Coin Switch 70-11-47 Miniature Bayonet Lamp 72-94068 #4-40 x %-Inch Truss-Head Screw 72-HA1404C #4-40 x Y4-Inch Pan-Head Screw

72-JA1405B #4-40 x 0.31-Inch Pan-Head Screw 75-14128 #4-40 x %-Inch Pan-Head Screw 75-9948 #4-40 Locknut 99-10008 Retainer

99-10042 Coin Switch Assembly for Belgian 5 Fr and U.S. $.25 99-10043 Coin Switch Assembly for German 1 DM, Japanese 100 Yen, Swiss 1 Fr 99-10044 Coin Switch Assembly for German 2 DM, Italian 100 L, U.S. $1.00 99-10045 Coin Switch Assembly for Australian $.20, German 5 DM, British 10 P

99-10068 Coin Return Chute

99-10075Switch Wire(included in coin switch assembly 99-10043)
99-10076Switch Wire(included in coin switch assembly 99-10042)
99-10077Switch Wire(included in coin switch assembly 99-10044)
99-10078Switch Wire(included in coin switch assembly 99-10045)

99-10080 Lamp Socket 99-10081 Key Holder 99-10096 Fastener

99-10104 Bar Retainer 99-10105, Bar 99-10115 Spring 99-10116 Plastic Coin Return Lever

99-10117 Steel Coin Return Door 99-10118 Amber Coin Return Button 99-10119. Amber Coin Button for U.S. $.25 99-10134 Coin Button Cover

99-10139 Coin Door 99-10140 Coin Door Inner-Panel Assembly 99-10141 Die-Cast Coin Return Cover 99-10142 Die-Cast Button Housing

99-10143 Coin Door Frame 99-10144 Channel Clip 99-10147 Harness 99-10148 Lock Assembly

99-10149 Service Door 99-10150 Switch Cover 99-10151 Left Coin Inlet 99-10152 Right Coin Inlet

99-10153 Coin Return Box 99-10154 Bracket Assembly 99-15066 Screw for Clamp 171006-035 Metal Coin Mechanism for U.S. $.25

Page 39

Rolling Thunder Illustrated Parts Lists

N O T E 5

4-15

Page 40

Illustrated Parts Lists

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL; Reproduction forbidden without the specific whiten permission of Atari Games Corporation, Milpitas, CA. This drawing is only Conditionally issued, and neither recerpt nor possession there confers or transfers any right in. or license to use, the subject matter of the drawing (oF any design or technical information shown thereon, nor any right lo reproduce this drawing or any part thereot, Except for manufacture by vendors of Atari Games Corporation, and for manufacture under the corporation's writen license, no right is granted to reproduce this drawing © the subject matter thereot, unless by writen agreement with or witlen permission from the corporation. Rolling Thunder

5, Ge gy Pons 9 10 btse5 Lay a

0011969198

U

sh 518519085) app 2063070 Sigpaa a Sa

F said Rits0e es

ar 2 ny ge oA Ato 1" [ome] aR e bots a. brsis3— ¥, (3375

< pss) bts « bis08

Dp Eg, iL . a 7 etc] it

2018 we]

ca

= f | *® # ae) $1575

voor 44 or l F eeA0%e iN ae) = ile ____ op. Be maa we 7 a It 1m

Figure 4-6 Rolling Thunder Game PCB Assembly 99-090284

Page 41

Rolling Thunder

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL. Reproduction forbidden without the specife wrtten permission of Atari Games Corporation, Mitas, CA. This drawing is only Conditionally issued, and neitner receipt nor possession thereat confers or transfers any right n, oF license lo use, the subyect matter of the drawing Or any design or technical information shown thereon, nor any ight to reproduce tins drawing or any part thereof. Except for manufacture by vendors of Atati Games Corporation, and for manufacture under the corporation's writen license, no right is granted to reproduce this drawing or the subject matter theréof, unless by written agreement with or wniten permission from the corporation.

8616961201 2 | 21512 E Se Keo S|] g Ee ‘Fle ae

=FloM
22512wisi

Lo 2

=*21512

=| 21512 Kt

i 21512 CUSIIS g PCS x 71512 al 26)

eeaSS

2 |

pee221512|
asae ae 02428°
721512Sagat=F
2BTwRID

Par | Fi rR 1 a aha = of] B| Rg 9K

BaR8 “eT weL|

gr a

inalae&
-15365REnh| Bate
“aPeSE
—es“Gr pcg8
aa;en|XTAL
(S251x|
aq1B

= fay cae =

shh”|gRieFa
aapsaage2|~i
aeaeg&ES"

A RB

§jspo

iz Bs dé 3éP PINDER

Figure 4-6, Continued Rolling Thunder Sub PCB Assembly 99-090285 Illustrated Parts Lists

Page 42

Illustrated Parts Lists Rolling Thunder

Rolling Thunder Game PCB Assembly

Parts List

Desig- Desig-

natorDescriptionPart No.natorDescriptionPart No.
Integrated Circuits8UIC, 74L87499-090115,
1EIC, Custom 98.99-0901568vIC,74L817499-090123
IRIC, Custom 9599-0901559AIC, 68A09EP99-090135
aeIC, Custom 9999-090157,9AIC, HDG8A09E99-090134
2F, 2tom 95,99-0901559c1C, PR EPROM, RT2-1, 27256, 2501ns,9C — 99-090223
3AIC, Power Amplifier, LA446099-0901609EIC, 741824599-090124
3FIC,M5M5165-70 (70 ns)99-090142oFIC,741837599-090129
aFIC, MB81C78-45 (45 ns)99-090143oMIC, Custom 4899-090154
3F>, MB8464A-70 (70 ns)99-090144ONIC,7480899-090220
3FIC, TMM2063P-70 (70 ns)99-090145opIC, Custom 2799-090148
3FIC, TMM2064P-70 (70 ns)99-090146OvIC, 741817499-090123
3HIC, 74180899-09011110CIC, Custom 4799-090153
3), 3KIC, 74HC25799-09013210MIC, M5M5165P-10 (100 ns)99-090140
3L, 3M41825799-09012510MIC, TMM2064P-10 (100 ns)9.090141
3RIC, PR EPROM, RTI-1, 7124, 45 ns,3R—-99-09023910NIC, 741813899-090117
38IC, PR EPROM, RT1-2, 7116, 45 ns, 3S99-09024010P, 10RIC, 74L$17399-090122
31, 3U,3VIC, 74L817399-090122108IC, 741537899-090131
4AIC, Op-Amp, LM324N99-09015910TIC, 74L817399-090122
IC, DAC, YM301299-090158HAIC, 68A09EP99-090135
IC,Custom 3099-090149HAIC, HD68A09E99-090134
IC, M5M5165P-10 (100 ns)99-090140MD-I1FIC, 741825799-090125
99-090141HHIC, 741837799-090130
99-090126UKIC, CXK5813D-45 (45 ns)99-090137
99-090241HKIC, Custom 9599-090155
IC, YM215199-09014711KIC, TMM2018D-45 (45 ns)99-090136
IC, 406999-09013311KIC, TMM2016BP-10 (100 ns)99-090139
IC, Custom 4299-09015111NIC,Custom 3999-090150,
IC, 7ALS15899.090121HUIC, CXK5813D-45 (45 ns)99-090137
IC, PR EPROM, RT 1-4, 7138, 45s, 5V_—-99-090242HUIC, CXK5808P-45 (45 ns)99-090138
IC, TALS245,99-09012411UIC, TMM2018D-45 (45 ns)99-090136
IC, 74183299.090114uvIC, CXK5808P-45 (45 ns)99-090138
IC, Custom 4399-090152VvIC, CXK5813D-45 (45 ns)99-090137
IC, PR EPROM, RT1-5, 7112, 35 ns, 699-090243lvIC, TMM2018D-45 (45 ns)9.090136
IC, 7417499-09022112AIC, 7418029.090109
IC, 741837399-09012712cIC, PR EPROM, RT2-2, 27256, 250 ns, 12C 99-090224
IC, 741825799-09012512EIC, 741824599-090124
IC, 741813999-09011812HIC, PR EPROM, RT1-9, 27512, 250 ns, 12H 99-090231
IC, 74LS1099-09011212KIC, PREPROM, RT1-10, 27512, 250ns, 12K 99-090232
IC, TALS0499-090110LLIC, PR EPROM,RT 1-11, 27512, 250.ns, 121 99-090233
99-0901 1312MIC, PR EPROM, RT1-12, 27512, 250 ns, 99-090234
IC, Custom 4299-09015112M
IC, M5M5165P-10 (100 ns)99-09014012PIC, PR EPROM, RT1-13, 27512, 250.ns, 12P_ 99-090235
IC, TMM2064P-10 (100 ns)99-090141LRIC, PREPROM,RT1-14, 27512, 2501s, 12R 99-090236
7SIC, PR EPROM, RT1-8, 27256, 250 ns, 7S — 99-090230.12TIC, PR EPROM, RT1-15, 27512, 250 ns, 12T 99-090237
7IC, 7ALS15899-09012112UIC, PR EPROM, RT1-16, 27512, 250 ns, 99-090238
"vIC, TALS8S99-09011612U
8BIC, 741825799-090125
8CIC, 74LS15799-090120Capacitors
8DIC, 74LS0099.090108clCapacitor, Electrolytic, 470 wk, 10 V99-090168
-74C2Capacitor, Electrolytic, 1000 wk, 25 V99-090169
8EIC, 74L-09rectoraedHS
Heic. eresoe iaGCapacitor, Electrolytic, 47 uF,6.3 V99-090167
8HIC. 741837499.090128C4Capacitor, Electrolytic, 2.2 uF, 25 V99-090165
8NIC, Custom 43,99-090152

4-18

Page 43

Rolling Thunder Illustrated Parts Lists

Rolling Thunder Game PCB Assembly

Parts List, Continued

Desig- Desig-

natorDescriptionPart No.natorDescriptionPart No.
aCapacitor, Electrolytic, 22 uF, 16 V99-090166PC26, PC29, Capacitor, Ceramic, 0.1 pF, 25 V99-090175
C6, C7Capacitor, Ceramic, .033 uF, 50 V, 410% — 99-090180PC30Capacitor, Ceramic, 0.1 pF, 25 V99-090175
8, C9Capacitor, Ceramic, 0.01 uF, 25 V99-090174PC33-PC36 Capacitor, Ceramic, 0.1 pF, 25 V99-090175
C10, C1Capacitor, Electrolytic, 10 wE, 16 V99-090170,PC38, PC40 Capacitor, Ceramic, 0.1 wE, 25 V99-090175
12Capacitor, Ceramic, 470 pk, 25. V99.090173PALCapacitor, Tantalum, TSD-A 4.7 4. 10V_—99-090177
cBCapacitor, Ceramic, 0022 uF 50 V, +5% — 99-090179PCALCapacitor, Tantalum, TSD-S 4.7 uF, 10V-99-090176
Capacitor, Electrolytic, 10 pk, 16 V99090170PC42-PC45. Capacitor, Ceramic, 0.1 pF, 25 V9.090175
Capacitor, Ceramic, 22 pF, 25 V99-090171PCGCapacitor, Tantalum, TSD-S 4.7 4F, 10V99-090176
Capacitor, Ceramic, 100 pk 25 V99-090172PCACapacitor, Tantalum, TSD-A 4.7 wR, 10V99-090177
Capacitor, Ceramic, 220 pk, 25 V99-090178PCA7Capacitor, Ceramic, 0.1 wE, 25 V9.090175

Diodes Resistors

DIDiode, Zener, RDG.2F(1 W, 5.8-6.6 V)99-090164RI, R2Resistor, 4.79, +5%, 4 W99-090187
RBResistor, 15K Q,+5%, %& W99-090197
Connectors and SocketsR4Resistor,6.8K Q, +5%, 4 W99-090195
IlConnector, Pin Housing, 3CKT99-090222RS.Resistor, 15K Q, +5%, 4 W99-090197
iSocket, 34CKT99-090207ROResistor, 6802, +5%, 4 W99-090188
IsSocket, 20CKT99-090206RTResistor, 18K @, +5%, 4 W99-090200
Socket, IC, L4CKT99-090216RSResistor, 22K Q, +5%, 4 W99-090198
Socket, IC, 16CKT99-090210ROResistor, 10K 9, +5%, %& W99-090196
Socket, IC, 20CKT99-090211RIOResistor, 3902, +5%, 4 W9.090190
Socket, IC, 22CKT99-090214RIResistor, 560.2, +5%, 4 W99-090192
Socket, IC, 24CKT99-090213RI2Resistor, IMegQ, +5%, 4 W99-090199
Socket, IC, 24CKT99-090212R13.Resistor, 3300, +5%, 4 W99-090189
Socket, IC, 28CKT99-090215R14Resistor, 10K Q, +5%, 4 W99-090196
Socket, IC, 40CKT99-090217RISResistor,4.7K Q, +5%, 4 W99-090194
Socket, IC, 42CKT99-090218RIGResistor, 1K, 5%, 4 W99-090193
Socket, IC, 64CKT99-090219RI7Resistor, 470 2, +5%, « W99-090191
onRIBResistor, 1802, +5%, 4 W99-090201
9%, a We-0901'
oscOscillator, MCO-1425B (49.152 MHz)99-090162Rio.Resistor, IK, £5%,Oe
oscOscillator, KXO-01-49M15299-090161Reaintor Mindules
RMIResistor, SIP Network, 220 Ohm x 4,%W99-090181
pcrconactionee Se5RM2Resistor, SIPNetwork, 470 Ohm x 4,W99-090182
Peuae sa ja rene os a naaraRM3Resistor, SIP Network, IK Ohmx 4, %W99-090183
rcnee aot asyas oy ilRM4Resistor, SIP Network, 2.2K Ohm x4, %W 99-090184
PCACapacitor, Tantalum, TSD-S 4.7 uF, 10V99090176es meMeee Eee Comm caKie, gomuiee
PCsCapacitor, Tantalum, TSD-A 4.7 uF, 1099-0901777aaale.
PCSCapacitor, Ceramic, 0.1 pF, 25 V99-090175Switches
PCTCapacitor, Tantalum, TSD-A4.7 wR 10V99-090177a‘itch, DIP,8CKT09020
PCTCapacitor, Tantalum, TSD-S 4.7 uF 10V_99-090176eaSea oriceeine
PCBCapacitor, Tantalum, TSD-A4.7 wR 10V99-090177SWBSwitch, DIP, 8CKT99-090204
PCBCapacitor, Tantalum, TSD-S 4.7 xR, 10V—99-090176SWBSwitch, DIP. 8CKT99.090205
PCO.Capacitor, Ceramic, 0.1 uF, 25 V99-090175
PC1OCapacitor, Tantalum, TSD-S 4.7 pE 10V—-99-090176Miscellaneous
PCIOCapacitor, Tantalum, TSD-A 4.7 #F, 1099-090177TI-T3Terminal, Fast-on Tab, .2509.090208
PCI1-PC14 Capacitor, Ceramic, 0.1 pF, 25 V99-090175VRIPotentiometer, Trimming, 2K 2, TMI0K 99-090203
PCISCapacitor, Tantalum, TSD-A 4.7 wR 1099-090177PV)
PCISCapacitor, Tantalum, TSD-S 4.7 4E 10V-99-090176vRIPotentiometer, Trimming, 2K @, TMIOK 99-090202
PCIG-PC21Capacitor, Ceramic, 0.1 uF, 25 V99-090175(PV) BUS
PC24Capacitor, Tantalum, TSD-A 4.7 uF, 10V — 99-090177x1Crystal, 3.579545 MHz99-090163

PC24, PC25 Capacitor, Tantalum, TSD-S 4.7 uF, 10V —_-99-090176 PC25 Capacitor, Tantalum, TSD-A 4.7 wE, 10V99-090177

4-19

Page 44

Iustrated Parts Lists

Rolling Thunder Sub PCB Assembly

Rolling Thunder

Parts List

Desig- Desig-

natorDescriptionPart No.natorDescriptionPart No.

Integrated Circuits Connectors

AlIc, 74499-090244iConnector, Header, 34CKT99-090276
A2IC, 406699-090246
8IC, HD637A01X099-090247Inductors
BLIC, 741824599-090124L1,L2Inductor, 100 mH, SP0406-101K99-090274
ElIC, 741836599-090245.
E2IC, Op-amp, TLO84CN9.090248Polarized Capacitors
FIIC. PR EPROM, RT1-17,27512, 250NS, FI99-090278PCI-PCI4.itor, Ceramic, .01 pF, 12 V99-090265
F2IC, 11599-090251_
BBIC, PR EPROM, RT 1-21, 27512, 299.090282tore
HIIC, PR EPROM, RT1-18, 27512,9.090279nSResistor, 10K 2, +5%, & W9.090196
HBIC, PR EPROM, RT2-22, 27512, 299-090283ReResistor, 3.3K 0, 25%, 4 W99-090258
KiIC, PR EPROM, RT2-19, 27512, 250NS,KI 99-0902807Resistor 10K G, °¢ 27014HOU
"onFinR4Resistor, 3.3K 2,+5%, 4 W99-090258,
MIIC, PR EPROM, RT 1-20, 27512, 250NS, MI 99-090281see.90ee
M2IC, Regulator, TL497ACN9.090249©Resistog 1008, 23%, 4ae
,RG, R7Resistor, 6.8K 2, 45%, 4“ W99-090195
;R8, ROResistor, 2.2K 9, +5%, 4 W99-090257

Capacitors 7 : ae

clCapacitor, Electrolytic, 47 uF, 25 V99-090271RIOResistor, 3.9K Q, + 5%, M w99-090259
C2Capacitor, Electrolytic, 100 ak, 16 V99-090273RUResistor, 4.7K 2,£5%, 4 W99-090194
3Capacitor, Electrolytic, 1 pF, 16 V99-090268R12, R13___Resistor, 47K Q,+599-090261
cs.Capacitor, Ceramic, .01 pF, +10%,50V — 99-090267R14-R16Resistor, 22K Q, 45%,W99-090198
75%.4W9.090254
6Capacitor, Ceramic, 0047 uF, £ 10%, 50V_ 99-0902667Resistor,19, £5%, 4 W79-090254
7,8Capacitor, Ceramic, 01 pF. 12 V9.090265RIBResistor, 27K 2, +5%, 4 W99-090260
C9, C10Capacitor, Ceramic, 22 pF, 12 V99-090262R19Resistor, 1.2K Q, +5%, 4 W99-090256

cul Capacitor, Electrolytic, 47 wk, 16 V 99-090270 Resistor Modul

clCapacitor,Ceic,.01 pF,v4\esistorModules
a3Coasior ceamie 0a AdeeRMIResistor, SIP Network, 2.2K 9x4, KW994090252
Cl4Capacitor, Ceramic, 0.1 pF, 50 V99-090264RM2, RM3_Resistor, SIP Network, SK Qx 899-090253
015cictviag1.09027:
e :Capacitor, Blectrolytic, 47 af 35 V99-090272ieee
C16Capacitor, Electrolytic, 10 nF, 16 V99-090269XTALCrystal, 6.000 MHz9.090275
C17Capacitor, Ceramic, 0.1 aE, 50 V99-090264Socket. IC, 64CKT99-090219
DiodesSocket, IC, 28CKT99-090215
DI,D2Diode, 18158899-090250

4-20

Page 45

Rolling Thunder

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific wnitten permisson of Atari Games Corporation, Milpitas, CA. This drawing is only Conditionally issued, and neither rece pt nor possession thereat confers or transfers any right in, oF license to use, the subject matter of the drawing 6 any design or technical information shown thereon, nor any ight to reproduce this drawing or any part thereo!. Except for manufacture by Vendors of Atari Games Corporation, and for manufacture under the corporation's writen icerise, no right is granted to reproduce this drawing or the subject matter thereof, unless by written agreement with or wtten permission from the corporation. Illustrated Parts Lists

NOTE: Components R1-R7, TP1, and TP2 should not be installed in ine PCB

poooeg » | = cot Of oa ° eo 027

i

spose 3 hfe eoccce ON) Dac cee eee S38

tieaccseee4, Aecccceccea 28§ca10 0oonOO.13

On oe AAR " foorry An: y D0 $66 é °

| Rtirrriaiistrsststisrsiii ee

Figure 4-7 End PCB Assembly A044201-01 A

End PCB Assembly Parts List

DesignatorDescriptionPart No.

Capacitors

c1-C211 wE 50 V Ceramic Capacitor122002-104
22.001 pE, 50 V Ceramic Capacitor122002-102
€23-C25470 pE, 100 V CeramicCapacitor122016-471
€26-C311 wE, 50 V Ceramic Capacitor22002-104
32, C33O1 pk, 25 V Ceramic Capacitor122005-103
34-C361 hE, 50 V Ceramic Capacitor122002-104

Diodes

CRI, CR2Type-1N4001 Diode31-1N4001

Connectors

JI, J211-Ckt., .1-Inch Ctr. Header Connector179118-011
3B6-Ckt., .156-Inch Ctr. Header Connector179213-006
49-Ckt., .156-Inch Ctr. Header Connector179213-009
ap)6-Ckt., .1-Inch Ctr. Header Connector179118-006
3656-Ckt., Right-Angle Edge Connector (Acceptable substitute is part no179240-056

179240-156) Resistors

R8OQ, +5%, % W Resistor110005-001

Miscellaneous

L1-L3,Ferrite Bead141003-005
CC+,CC+Test Point, .187 x .031179051-001
TP3Test Point, .250 x.031179051-003

SPDT Miniature Slide Self-Test Switch 2-Ckt., .1-Inch Ctr, Header Connector (Service Switch) 69-004 179118-002

4-21

Page 46

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 47

Warranty

Seller warrants that its printed-circuit boards and parts thereon are free from defects in material and workmanship under normal use and service for a period of ninety (90) days from date of shipment. Seller warrants that its video displays and laser video disc players (in games supplied with displays and video-disc players) are free from defects in material and workmanship under normal use and service for a period of thirty (30) days from date of shipment. None of the Seller's other products or parts thereof are warranted. If the products described in this manual fail to conform to this warranty, Seller’s sole liability shall be, at its option, to repair, replace, or credit Buyer’s account for such products which are returned to Seller during said warranty period, provided:

  • Seller is promptly notified in writing upon discovery by Buyer that said products are defective;
  • Such products are returned prepaid to Seller’s plant; and
  • Seller’s examination of said products discloses to Seller’s satisfaction that such alleged defects existed and were not caused by accident, misuse, neglect, alteration, improper repair, installation, or improper testing. In no event shall Seller be liable for loss of profits, loss of use, incidental or consequential damages. Except for any express warranty set forth in a written contract between Seller and Buyer which contract supersedes the terms herein, this warranty is expressed in lieu of all other warranties expressed or implied, including the implied warranties of merchantability and fitness for a particular purpose, and of all other obligations or liabilities on the Seller's part, and it neither assumes nor authorizes any other person to assume for the Seller any other liabilities in connection with the sale of products by Seller.

The use of any non-Atari parts may void your warranty, according to the terms of the warranty. The use of any non-Atari parts may also adversely affect the safety of your game and cause injury to you and others. Be very cautious in using non-Atari-supplied components with our games, in order to ensure your safety. Atari distributors are independent, being privately owned and operated. In their judgment they may sell parts or accessories other than Atari parts or accessories. Atari Games Corporation cannot be responsible for the quality, suitability or safety of any non-Atari part or any modification including labor which is performed by such distributor.

Page 48

NN NN \

Ww So \

\

Atari Games Corporation @ 675 Sycamore P.O. Vi Miipitas, California 95 035

Lttzjziz¢: