Bubble Bobble
Bubble Bobble (Japan, Ver 0.1) (Taito Corporation, 1986) · Manual · 16 pages · 16 sections · original scan
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
Before You Get Started. . .Stop!
Does your new game package include all listed parts? (Is it complete?)
- Isthe game you have chosen to transform able to supply all the required voltages for the new game?
- Is the monitor configuration compatible? In most games it is rather difficult to change the monitor from a vertical mount to a horizontal mount. We recommend you choose a game cabinet with the same mount as your new game requires.
- Do you have the necessary tools? (See the recommended tool list)
Caution
F.C.C. Regulation Compliance
This is to avoid radio frequency radiation and comply with the limits for a class “A” computing device pursuant to sub-part ‘J’ of part 15 of F.C.C. rules, which are designed to provide reasonable protection against interference when operated in a commercial environment. Operation of this equipment in a residential area is likely to cause interference
- in which case, the user at his own expense, will be required to take whatever measures may be required to correct the interference. Metalized FCC compliance label must be attached and visible on the outside of the cabinet (rear) upon completion of installation.
Installing and Servicing Your
BU SBLEIBORE! E
New Game Package
Table of Contents
New Game Package Contents........ 0... e cece eee eee nee eeeees 2
Power and Monitor Requirements... 0.0.0... cee cece cece cence eeeeee 2 Recommended Tools and Supplies #6 65 Mid PSE ea ee ec ee ee eetwncews 3 Dip Switch Tables .... 6... cece cence nee e teen eeenee 3&4 Game Operation... 1... cece cece cect e te eneeeeneenns 5 Installation Procedures... 2... cece cee cece eee eee eeneneeeee 6
Control Panel Positioning ©... 6... cece cece een n nee eeeeennes 12 Main Harness Connections ... 2.0.2.0... cece cece cece eeeees outside back cover
BSBLEBOBSIB NEW GAME PACKAGE CONTENTS
1 Main Printed Circuit Board (PCB) 1 Marquee 1 Control Panel Overlay 1 Set Legs, Bolts, & Spacers 1 Plex Control Cover 1 Connecting Wire Harness 1 Set Side Graphics 2 Two-Way Joystick 1 Set Play Instructions & Function Labels 6 Player Button Assemblies 1 Service and Installation Manual
POWER REQUIREMENTS MONITOR REQUIREMENTS
+5 VDC 7 amp minimum Horizontal Mount Raster Scan +12 VDC lamp minimum Negative Composite Sync -5 VDC Tamp minimum
Recommended Tools and Supplies
ROMSTAR new game package. Phillips and Slot Screwdrivers Socket Set Enthusiastic Attitude Wire Cutters and Strippers Pliers or Channel Locks Planning and Careful Thought Electric Drill 3/32" © 1/4” © 7/16" Drill Bits 1/4" Plex Bit 1-3/16” Chassis or Sheet Metal Punch 1 1/4” Plex Hole Saw Glass of Water and a Snack Smail File Razor Knife and Sharp Blades Straight Edge Patience Common Sense
Dip Switch Tables
Optimize Your Profits Painting Supplies (if you do your own Painting) Paint Brush and Paint (don’t forget the primer) Paint Roller and Pan Sand Paper Putty Knife and Wood Putty A Good Nights Sleep Staple Gun and Staples Soldering Iron and 60/40 Resin Core Solder Vacuum Cleaner Assorted Fastening Hardware Shrink Tubing: 3/32” © 1/8” © 3/16” Masking Tape 3 1/2" OR 4” Wire Ties Spray Window Cleaner and Rags (baby diapers work GREAT!)
Thorough Research shows that two and a half minute games both satisfy players and also keep the quarters flowing. If games aren't running about two and a half minutes long, then collections probably aren't at their peak. You'll want to tailor your game to your location. The trick is to adjust a few DIP switches. (See the chart in this book.) It’s easy!
Dip-Switch Bank A
Adjustment Options
Screen normal invert Test Mode (power off) (power on) normal game test mode
Pause (while in game) — normal game stop game Attract Sounds ~on-
off
Coin, 1 jin 1 play 2 play nN] ryfalalrml| ro] ala
Dip-Switch Bank B
Adjustment Options pit 2 3/4/5/6]7]8 Difficulty
| 30,000 | /100,000 | / | 400,000 |
/ 80,000 300,000
| 40,000 | /200,000 | 500,000 |
| 50,000 | /250,000 | 500,000 |
Number of Plays -3- off | off on | off off | on on] on
—__Game Operation
BUSBLEIBORE! E
“ CONTROL BUB (1st PLAYER) & BOB (2nd) PLAYER AND DESTROY ALL OF THE BADDIES.
e FIRST: BLOW BUBBLES AT THE BADDIES. © NEXT: POP THE BADDIE BUBBLES WITH YOUR HORNS OR TAIL SPIKES. © THEN: COLLECT THE BONUS.
O@®eo
- HINTS:
- BY POPPING BUBBLES FIRE, LIGHTNING & WATER YOU MAY USE THESE THINGS TO DESTROY BADDIES.
- TO GAIN HEIGHT YOU MAY JUMP ON BUBBLES (EVEN YOUR OWN). © TO GET SPECIAL POWERS, COLLECT CHARMS (HEARTS, CROSS, ETC.)
Installation Procedures
Something To Think About Your final product will be anew game. You have made a wise decision to transform a game that has seen better days in the all important cash box into anew game. This is by far the most cost effective alternative to maximize the return of your initial investment. All you provide is the cabinet with a power supply and a monitor. Oh yes, you will need a touch of elbow grease. And that's it! We provide the rest. The end resultis ... anew game ata very low cost. Fact: Spend a little time on the cabinet’s appearance (i.e. marquee, control panel and cabinet graphics). With a little paint, some wood putty and new lights, you will raise the profits of any game. . especially with the introduction of anew game package. The new game look should always apply to the inside of your game as well as the outside. A few wire ties and shrink tubing on your harness; some fastening hardware on your subassemblies and a sweep with the ol’ vacuum cleaner will ensure that unnecessary glitches do not occur. Remember: You are creating anew game . If you have any questions or just need some advice on any of your new game transformations, don’t hesitate in giving a member of our technical staff a call.
Let’s Get Our Hands Dirty
Preparing the Original Game for the New Game Remove the following:
| 1, | Main logic board(s) | 4. | Monitor Bezel |
| 2. | Control panel | 5. | Marquee |
| 3. | Monitor plexiglass | 6. | Graphics |
| would recommend painting your cabinet to give it a fresh new look. (If it is geographically inconvenient to make use of our facilities, you may consider having an auto body shop take care of your painting needs.) If your cabinet has wood grain sides; remove old graphics and adhesive (adhesive may be removed with lacquer thinner. If you intend to use your original plexiglass, be sure it is in mint condition or it should be replaced. Thoroughly clean out your cabinet.
Time To Install Your New Goodies
Before You Start. ..Remember DO NOT Do This Work With The Power On!
Logic P.C.B. Cage
Mount the logic cage securely (away from power supply). A Mark and drill pilot holes (3/32”). B Place the logic cage (bottom) over the holes and secure it with the supplied wood screws. C Install the PC.B. into the logic cage. Use feet and spacers supplied and adjust them so that the screws will go through the slots int he cage bottom.
Wire Harness
Attach the wire harness connector to the main logic board. CAUTION: Sometimes the connector is not keyed and it is very easy to install it reversed on the logic board. Even if it is keyed, always triple check to be sure the wire inputs were connected correctly to the connector and the connector to the logic board.
Connecting the Wire Harness to the Existing Wires
When you hook up the control panel, power supply, monitor or other subassemblies that remain in the game cabinet to your new wire harness, try and use their existing secondary connectors.
- Cut the original wire approximately three inches from the original connector. Strip off about one half inch of insulation.
- Solder the new wire designated for that position to the original wire you just stripped.
- Melt shrink tubing around all your in-line wire connections. Do not use electrical tape. Tape could unravel over a period of time due to the cabinet heat and cause you a great deal of trouble.
- Use wire tie wraps, and secure the cable to the cabinet whenever it seems necessary. Remember this is a new game , not a sloppy conversion.
Power Wires
1, Connect the wires that are designated for your power supply. You will need a supply of +5V, +12V & ground. Your new game package may not require all of the voltages that were used in the original game. Tie off any unused wires.
- You will notice that you probably have more than one wire for each voltage. It is a good idea to use all wires supplied (double up if it is necessary). This will help to ensure that you don’t overload the edge connector pins and cause them to “burn”.
Monitor Wires
You will be connecting the wires designated for the RED, GREEN & BLUE video guns along with the SYNC & GROUND wires.
Speaker Wires Find the two wires that are designated for the speaker and hook ‘em on up.
Coin Door Wires
- Connect the designated wires to the coin switches and meter.
- Youcanconnect your door lamps to the unused -5V power supply. Some games have separate power outputs for the coin door lamps.
- Be sure to clean and lubricate your old coin mechanisms. Keep the money coming in.
GUESS WHAT?
You are almost done with the electrical connections of your new game. All you have left is the contro! panel wiring. But we are going to hold off on that for right now. We have a few other things we need to do first. So why don’t you go ahead and get yourself a drink of water and stretch your legs. When you return, we can take a fresh look at your progress and then move forward.
Smoke Test
What Test?
Don’t worry. All this means is that you are ready to apply power to the system for the first time and you pray that there will be no smoke from a simple oversight. You are just about ready to power up the logic board. But first we need to recheck your work.
- Carefully inspect the game for loose power wires, exposed connections and extra fastening hardware.
- Make sure the logic board, board cage, monitor and Power supply are securely fastened in place.
- Double check the connectors to be sure they are wired and connected properly.
- Set the dip switches on the logic board to the factory recommendations. (Refer to page 5.) Also, be sure you set the dip switches for “DEMO WITH SOUND”. This will enable you to hear as well as see that your new PC.B. is functional.
Time to Apply Power:
1. 2. Look and smell for smoke. (TURN OFF IMMEDIATELY IF ANY IS NOTICED) Listen for game sounds. If after one minute you have not heard any sounds: A) Check for proper dip switch settings. B) Adjust volume control and check speaker connections. C) Check the +12V power supply to the logic board
HORIZONTAL SYNC INPUT FROM P.C.B. S Vcc {OR COMPOSITE SYNC INPUT} HORIZONTAL SYNC OUTPUT TO MONITOR {OR COMPOSITE SYNC OUTPUT) VERTICAL SYNC INPUT FROM P.C.B
VERTICAL SYNC OUTPUT TO MONITOR
B) Now how’s your picture? © it it centered?
- Is it too bright or dim? ¢ Is it in focus? Check your monitor manual for these adjustments. If your screen looks “off”, then your new game transformation may have been in vain. So let’s take the time to make the monitor look great. C) Is the picture upside-down? Dip switch 2 0n switch bank A should solve your problems.
Control Panel Assembly
1.
2.
3. Remove the buttons, joysticks and wire harness and put them aside fro now. Do not remove the original panel overlay until the new holes have been drilled. Mark positions on the panel for the new holes. ROMSTAR supplies a clear 1/8” thick piece of plexiglass with every new game package to cover the control panel. We feel that your new game investment is well worth protecting. . .and the control panel is the first place to show wear and tear.
- You will need to cut this piece to size. Use the control panel as a template. ¢ Use a razor knife to score the plexiglass deeply. Then use a pair of Pliers to break away the extra plexiglass. Now drill the holes in your panel that you have marked off for the buttons, Joystick and bolts. Hint: For best results, use a chassis or sheet metal punch for button holes. Drill the same holes on your plexiglass panel protector. Once again use your panel as a template. Hint: To avoid chipping while you are drilling the holes, place the plexiglass securely on a soft wood surface and use a plexiglass drill bit and hole cutter. The holes are now all cut. Smooth them out on your panel and plexiglass with a fine toothed file. Remove the original graphics overlay from the panel. Clean up the panel and install your ROMSTAR graphics. Make It Easier: Peel the top half of the protective backing off of your graphics. Start from the center and smooth out your overlay. Make sure you have about an inch extra coming off the top. Vo bubbles please. Now peel off the bottom half and do the same as you did for the top. Adhere the instruction and function labels. Install the Plex Contro! Cover over your completed new game panel.
Marquee Installation
Using the original marquee as a template, Center your new game marquee graphics and score the new marquee deeply to fit the cabinet. Break off the excess with pliers. Be sure the light behind the marquee works. Everything should always work on a new game. Take your time ... Don’t forget this is going to be a mew game.
Side Graphic Installation
Be sure sides of game are clean and free of old adhesive, dust, etc.
- Mark position of decal with eraseable pen or pencil (centered on upper half of cabinet).
- Peel off top 1/4 of decal backing and apply to cabinet with a smoothing motion (use a soft rag). Continue peeling off backing and smoothing.
- Remove any small bubbles with a pin or razor blade (pop them!)
Finishing Touches
- Check the game inside and out for any imperfections. Secure any loose wiring or fastening hardware.
- Make sure the coin door is tight and the coin mechs are well adjusted. A game is no good to anybody if you can’t get a coin into it.
- Once again go over every step of this mew game transformation in your mind. Be sure everything is correct and to your liking.
- Power up the game. A. Check all the coin switches. (Does the coin meter work?) B. Play your new game . © Are all the player controls working?
- Are the game sounds present? Is the volume level proper?
- Are the dip switches set properly? Well, that’s about it. Good Luck.
ai
6 BOB 2 WAY JOYSTICK i mo 06 wo BUBBLE JUMP BUBBLE
Control Panel
O VOLUME
WARRANTY, REPAIR AND RETURN POLICY
THIS POLICY WILL REMAIN IN EFFECT FOR A PERIOD OF ONE YEAR FROM DATE OF PURCHSE FROM ROMSTAR. UPON EXPIRATION OF THIS ONE YEAR PERIOD, ROMSTAR WILL CONSIDER P.C.B. REPAIRS ON A BOARD—TO—BOARD BASIS, BUT IS NOT RESPONSIBLE FOR REPAIR OR REPLACEMENT.
- *45 DAY FULL PARTS WARRANTY.
2 *60 DAY FULL ELECTRONICS WARRANTY (SEE RMA BELOW).
3, MINIMUM $40.00 SERVICE CHARGE FOR ALL NON-WARRANTY REPAIRS OR
RETURNS.
- ANY UNAUTHORIZED NON-FACTORY REPAIR OR ATTEMPTED REPAIR VOIDS
WARRANTY.
(*ALL WARRANTY PERIODS BEGIN ON THE DATE OF PURCHASE FROM ROMSTAR}
RETURN MERCHANDISE AUTHORIZATION — {RMA}
- ALL RETURNED MERCHANDISE MUST HAVE AN RMA NUMBER CLEARLY VISIBLE ON THE OUTSIDE OF THE PACKAGE.
2 ALL RMA NUMBERS MUST BE OBTAINED FROM ROMSTAR BY AN AUTHORIZED ROMSTAR DISTRIBUTOR. (PLEASE HAVE ROMSTAR SERIAL NUMBER AVAILABLE WHEN CALLING FOR AN RMA #).
- ALL PE BOARDS RETURNED TO ROMSTAR WITHOUT AN RMA NUMBER WILL BE SUBJECT TO A MINIMUM CHARGE OF $40.00.
- ROMSTAR WILL SHIP ADVANCE REPLACEMENT BOARDS TO DISTRIBUTORS OR AT DISTRIBUTORS REQUEST, DROP-SHIP BOARDS DIRECT TO THE OPERATOR.
- ADVANCE REPLACEMENT BOARDS WILL BE BILLED TO THE DISTRIBUTOR UNTIL RECEIPT OF A RETURNED BOARD BY ROMSTAR AT WHICH TIME A CREDIT WILL BE ISSUED.
6 ALL REPAIRS AND/OR REPLACEMENTS WILL BE SHIPPED BY ROMSTAR WITHIN 24 HOURS OF RECEIPT OR REQUEST. (SUBJECT TO AVAILABILITY OF BOARDS).
- FORANY ROMSTAR PRODUCT PURCHASED AFTER 3/1/86, A ROMSTAR WARRANTY CARD MUST BE ON FILE FOR EACH BOARD TO FACILITATE REPAIR & RETURN.
ANY QUESTIONS CONCERNING THESE POLICIES SHOULD BE DIRECTED TO DENNIS SABLE, TECHNICAL MANAGER OR SHAWN ZENKER, OPERATIONS OFFICER.
BUBBLE BOBBLE WIRE HARNESS (G)
COMPONENT SIDE WIRE COLOR
Ground | Black wn SOLDER SIDE
Video Ground Video Blue
Coin Switch Coin Meter
N/U N/U IP Right IP Left 2P Right Yellow 2 Left Violet
BUBBLE
oe JUMP
t-*{— NZ Me ee ane JUMP Orange
BUBBLE BOBBLE WIRE HARNESS (G)
COMPONENT SIDE SOLDER SIDE
Ground Ground Ground UN] B C Ground Black | Ground Black [| DO [Ground Black ; BUBBLE BOBBLE WIRE HARNESS (H)
WIRE | CONNECTION COLOR [Black [Ground [1 [Black_| Ground 3 [sik | Grn Fa
voc unreg) | 9 | et | Yellow [+i2vOC 11
JU... |_| #!2V0C (unreg) and +12VDC may be wired together.
BUBBLE BOBBLE COIN SWITCH JUMPER Ifyou wish to use your ” B, B.” conversion without a coin meter, a small wire jumper must be installed across the points of J7 located near IC 60 (the large brown SIP IC near the “G” connector).
METER HOOK-UP: Connect | lead of the meter to terminal 9of the “G” connector and the other lead to terminal 9 (+12VDC) of the “H” connector. The coin meter is activated by the voltage (@+6VDC) dropped from the +12VDC through a resistor.