CATHODE RAY TOMES

GP Rider Upright Type Owners Manual 1st Printing SP (420-5953-02)

GP Rider (World, FD1094 317-0163) (Twin setup) (Sega, 1990) · Owner's Manual · 38 pages · 10 sections · original scan

Page 1

aR: SEGA ENTERPRISES, LTD.

"MANUAL NO, 420-5953-02

Page 2

GP RIDER

BY: SEGA Enterprises, Inc. (U.S.A.) 2149 Paragon Drive San Jose, California 95131 Phone Number (408) 435-0201 FAX Number (408) 435-0294

SPECIFICATIONS

71 in. 49 in. ; . 36 in. NET WEIGHT: 463 Ib.

Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his/her own expense.
Page 3

Table of Contents

Introduction 1 Handling and Installation Precautions 1 Prevention of Counterfeiting and Conversion Labelling 2 Precautions Concerning the Place of Installation 3 F.C.C. Requirements 3 Name of Parts 4 Parts for Design 6 Service Switches 8 Removing the Handle Unit 9 Adjusting the Accelerator/Brake 12 Shift Switches 14 Assembly, Handle Unit 15 Monitor Adjustments 23 Test Mode 24 Bookkeeping 29 Dip Switch Setting Options 32 Eprom Locations 33 Wiring Diagrams 34

NOTE: DESCRIPTIONS HEREIN CONTAINED MAY BE SUBJECT TO IMPROVEMENT OR CHANGES WITHOUT NOTICE.
Page 4

INTRODUCTION OF THE OWNER’S MANUAL

SEGA ENTERPRISES, LTD., supported by its high electronic technology of LSIs, microprocessors, etc. and a wealth of experience, has for more than 30 years been supplying various innovative and popular game machines to the world market. This OWNER’S manual is intended to provide detailed comments together with all the necessary information covering the operation in general of electronic assemblies, electromechanical servicing control, spare parts, etc. The manual is intended for those who have knowledge of electricity and technical expertise especially in ICs, CRTs, microprocessors, etc. Carefully read so as to acquire sufficient knowledge before working on the machine. Should there be a malfunction, non-technical personnel should under no circumstances touch the interior system.

HANDLING PRECAUTIONS

When installing or inspecting, be very careful of the following points and pay attention to ensure that the player can enjoy the game safely.

o Be sure to tum the power off before working on the machine. 0 To insert or pull out the plug quickly is dangerous. 0 It is necessary to make sure that the power cord or the grounding wire is not exposed on the road, etc. in a manner so as to be dangerous. Make sure that grounding connections are made safely at the position where specified. Do not use any fuse that does not meet the specified rating. Make complete connections for the IC board and other connectors. Insufficient insertion is very dangerous.

Also, for the IC board circuit inspections, only the logic probe is allowed. The use of a tester is not permitted, so be careful in this regard. After confirming that there are no irregularities, turn the power ON.

Page 5

PREVENTION OF COUNTERFEITING AND CONVERSION

LABELLING To prevent counterfeits and conversions, the following labels are put on all the SEGA products. When handling such goods, be sure to confirm the labels. They are used to prevent illegal acts such as the unauthorized copying of the products and the printed circuit boards thereof or carrying on business by manufacturing similar merchandise or by converting, selling or using such products or printed circuit boards.

The following seal is put on the machines manufactured by SEGA

A te tote nn se st se a ae te ry ere errr ee

ORIGINAL SEAL

COPYRIGHT NOTICE _ This SEGA product has the copyright notice as follows:

© SEGA 1990

This signifies that this work was disclosed in 1990 and is the property of SEGA ENTERPRISES, LTD.

Page 6

PRECAUTIONS CONCERNING THE PLACE OF INSTALLATION

This is an indoor game machine. Absolutely do not install it outside. Even indoors, avoid installing in places mentioned below so as to ensure proper usage:

Places subject to rain or water leakage, or condensation due to humidity. In the proximity of an indoor swimming pool and/or shower. Places subject to direct sunlight. Places subject to heat sources from heating units, etc., or hot air. Vicinity of highly flammable/volatile chemicals or hazardous matter. Sloped surfaces. Vicinity of anti-disaster facilities such us fire exits and fire extinguishers. Places subject to any type of violent impact. Dusty places. Residential Environment - (See F.C.C. statement below) ooocooooceo

F.C.C. REQUIREMENTS

The Federal Communications Commission requires that all Class A equipment be verified and labeled as follows:

This equipment complies with the requirements in part 15 of FCC Rules for a Class A computing device. Operation of this equipment in a residential area may cause unacceptable interference to radio and TV reception requiring the operator to take what ever steps are necessary to correct the interference.

This label must be permanently attached in a conspicuous location and the text ; “s Jabel is ¥ . ; . rr ion Ui icatio 1 CT. amended,

Page 7

NAME OF PARTS

DESIGN PLATE

(423-0146)

HANDLE UNIT

RED

BLUE

COIN CHUTE DOOR

CASH BOX DOOR

TOOL (TAMPERPROOF WRENCH)

M4 540-0006-01

M5 540-0007-01

M8 540-0009-01

Page 8

NAME OF PARTS

ASSY SHIELD CASE : GPD-1058

ASSY PWR SPLY

GPD-40001

Page 9

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 10

ITEM NO, PART NO. DESCRIPTION NOTE

1423-0146Design Plate GP Rider U/R
2GPD-1022-AFront Glass - Left, Clear
3GPD-1022-BFront Glass - Right, Clear
4422-0349Play Instruction Plate, GP Rider U/R_
5421-7745Side Decal, GP Rider - Right
6421-7744Side Decal, GP Rider - Left
7421-7760Sticker, Direction (Arrow Red - Blue)
8421-7746Decal, Front Red ~ Right
9421-7747Decal, Front Blue - Left
10HSD~-2040-BSticker Meter A (Handle Assy)
ll| HSD-2040-CSticker Meter B (Handle Assy)
12GPD-1023-AMonitor Card, Blue - Left
13GPD-1023-BMonitor Card, Red - Right

| 560-5164 Xformer, 120 Primary - 18.5 5A, 100 3A Sec. t 200-5090 | Monitor, 19" Standard Resolution

|l 837-7273Communication Board, GP Rider

| | 834-7626-01 IC Board, GP Rider

839-0329 Filter Board GP Rider A

|839-0330Filter Board GP Rider B|
|601-6227-0Power Amp W/Switching Regulator 12V 5A
Page 11

SERVICE SWITCHES

Open the COIN CHUTE DOOR, and the following SERVICE SWITCHE’S layout will

appear :

oe LEFT PLAYER prrcccc core rr cnr cre - & : - SWITCH

kere vine RIGHT PLAYER

  • «a- <m 4 SWITCH

DEMAGNETIZING SWITCH

SERVICE SWITCH

TEST SWITCH

VOLUME ADJUSTMENT

OPERATING INSTRUCTIONS:

TEST SWITCH SERVICE SWITCH.. ..For operating this switch, see TEST MODE. .. Used for the purpose of servicing and increasing the credits without registering on the meter. DEMAGNETIZING SWITCH............. Not Used VOLUME ADJUSTMENT..................Used for adjusting the SPEAKER volume.

Page 12

REMOVING THE HANDLE UNIT

eo When adjusting the centering V.R., remove the HANDLE UNIT by using the following procedure:

TAMPERPROOF TAMPERPROOF

SCREW SCREW

M8x30 — eae a

oN TAMPERPROOF SCREW M8x30 SCREW M8x25

DISASSEMBLING PROCEDURE

For the adjustment of the centering V.R., take off the six TAMPERPROOF SCREWS by using the TAMPERPROOF WRENCH (M8), and the illustrated layout will appear.

Page 13

HANDLE’S CENTERING ADJUSTMENT

o When the HANDLE is in a stationary position, display the following on the screen in the SELF-TEST mode.

o At this time, if the variable value becomes 80H, it is

considered normal,

SCREW A a

ADJUSTMENT GEAR 601-6005

ADJUSTING PROCEDURE

INPUT TEST @ The V.R, BRACKET can be moved in the right and the left directions by releasing 2 SCREWS A which fasten it. @ move the V.R, BRACKET to the right to SHIFT A OFF disengage the PINION GEAR and the ADJUSTMEN'T SHIFT B OFF GEAR. At this time, make adjustments by BANK turning the V.R. SHAFT in a manner so that ACCEL the variable value falls within the BRAKE allowable range. @In the case where fine adjustments are necessary, loosen the ADJUSTMENT GEAR'S COIN #1 OFF START OFF COIN #2 OFF SERVICE OFF

SCREWS B and make adjustments as required.

7CH 7DH 7EH 7FH 80H 81H 82H 83H 84H

/ ALLOWABLE RANGE

Page 14

REMOVING THE HANDLE COVER

© When adjusting the V.R. for the ACCELERATOR/BRAKE, remove the

HANDLE COVER by using the following procedure.

TAMPERPROOF SCREW

TAMPERPROOF SCREW

TAMPERPROOF "SCREW M4x10

TAMPERPROOF SCREW 4x10

[DISASSEMBLING PROCEDURE

@ Remove 5 SCREWS which fasten the HANDLE COVER by using the

TAMPERPROOF WRENCH (M4).

  • The HANDLE COVER can be detached from the HANDLE UNIT in accordance with @ above. It is removable from the HANDLE UNIT by disconnecting the CONNECTOR (WHITE 4P MINI)

~11-

Page 15

ADJUSTING THE ACCELERATOR/BRAKE

BRAKE SIDE PINION GEAR 601-5252 \ BRAKE GEAR / 601-6005

SCREW B ACCELERATOR M4x10 SCREW A \ GEAR M4x10 601-6172 ACCELERATOR SIDE PINION GEAR 601-5252

| ADJU NG THE ACCELERATOR V.R.

(Remove the HANDLE COVER (see Page 13 ). @ Loosen SCREWS A and move the GEAR in a manner so that the variable value as specified in P 19 is obtained. @) When the specified variable is obtained, retighten SCREWS A.

{ ADJUSTING THE BRAKE V.R.

(Ty Remove the HANDLE COVER (see P 13 3. @ Loosen SCREWS B and move the GEAR in a manner so that the variable value as specified in P 19 is obtained. (@)When the specified variable is obtained, retighten SCREWS B.

Page 16

REPLACING THE V.R. THE ACCELERATOR/BRAKE

_SCREW V.R. BRACKET M4x8 _- HSD=2027X

M4x8 V.R. 5k9 B TYPE \ SCREW \ 220-5130

\ \_V.R. BRACKET NUT A BSD-2027

DISASSEMBLING PROCEDURE |

1. To remove the BRACKET from the HANDLE UNIT, take off the 2

screws which fasten the V.R. BRACKET.

To remove the PINION GEAR attached to the V.R. SHAFT to be

replaced, release the 2 SET SCREWS Lhat fasten the PINION

GEAR.

The V.R. can be removed from the BRACKET by taking off the

v.R. SHAFT'S NOT A.

After the replacement has been made, reassemble them in sequential order opposite from the above procedure.

=13-

Page 17

REPLACING THE SHIFT SWITCHES

SWITCH CASE SHIFT-UP SW (RED) OO

SHIFT-DOWN SW (GREEN) 4

When replacing the SHIFT SWITCH(ES), apply a plier, etc., to the edges of the switch(es), and while slightly moving it up/down and or left/right, take it out. Insert wires to the new switch in the same manner as for the old one, and push it in by matching the switch convex portion and the case concave portion.

Page 18

ASSY HANDLE U/R (GPD-—20001) (D-1/8)

Page 19

ASSY HANDLE U/R (GPD-20001) (D-2/8)

Page 20

ASSY HANDLE U/R (GPD-20001) (D-3/8)

Page 21

ASSY HANDLE U/R (GPD-20001) (0-4/8)

ITEM NO.| PART NO. DESCRIPTION NOTE

1 | GPD-2010HANDLE BASEEB
2 | HSD-2100ASSY CENTERING1D
3| HSD-2030PANEL HOLDERsy

4 HSD-2031 FRONT PANEL ed

5HSD-2032WOODEN BASE UPPER|
6 | HSD-2033WOODEN BASE LOWERron
7 | GPD-2012HANDLE COVEREOD
8 | HSD-2002ACCEL GRIPSET) ND

9 GPD-2011 SHIFT GRIP me)

10 | HSD-2004ASSY BRAKEa
1| HsD-2015STOPPER Disk@
12| BsD-2016TORSION SPRINGapr
13| HSD-2017SPRING HOLDER
14 | HsD-2018GEAR HOLDER> |

13 | HsD-2019 KEY 4x4x12 16 | HSD-2020 SLIDE SPACER

7HSD-2042SLIDE PLATE INNER(ees
18| HSD-2022SLIDE HOLDERse
19| HSD-2023SWING ARM HOLDEReg
20 | HSD~2024SWING ARM8

21 | HSD-2025 HOLD PLATE

22 | HSD-2026SWING ARM SHAFTa

L {| =

23HSD-2027XVR BRKTie
‘HSD-2037|CHAIN HOLDER B)
25| HN-5046SPACER TUBE@
26HSD-2038CHAIN| SOD
Page 22

ASSY HANDLE U/R (GPD-20001) (D-5/8)

ITEM NO.| PART NO. DESCRIPTION 27 | HSD-2034 BUMPER HOLDER R

2| HSD-2035BUMPER HOLDER Lé
29 | HN-S024xBUMPERfy
30 | HSD-2036SLIDE PLATE OUTEREos

31 | HSD-2048 = | HOLDER VR BRKT ee

32| HSD-2044xVR BRACKETCe
33} eo1-5410GEAR 15 26OF!
34| 601-6005ADJUST GEAR&)
35| 601-6172GEAR 48
36 | GPD-2007SWITCH CASE&) |
37| Mx-2020TUBE HOLDERS&S
38 | MX-2021PROTECTOR W/S TUBEoOo
39 | 421-7752STICKER UP DOWN(25) |
101| 100-111BEARING 212©)
102 | 100-5112BEARING £17o) |
103 | 220-5130VOL CONT B-5K OHMee
104| 509-5218PUSH BTN SWITCH 1T YELLOW W/LAMPOF
105509-5003PUSH BUTTON SW 1T (114.2 GREENa|

108 | 509-500-083 | PUSH BUTTON SW 1T [ia2 RED ff

107 | 280-5009CORD CLAMP ¢21Ep |

201 | 000-0408-FS_ | M SCR PH W/FS M4x8 202 | 031-0630-B CRG BLT BLK M6x30 203 | 008-0410 TMP PRF SCR TH M4x10 204 | 050-0006 HEX NUT M6

Page 23

ASSY HANDLE U/R (GPD-20001) (D-6/8)

ITEM NO. PART NO. DESCRIPTION NOTE

205 | 000-0514-FS_- | M SCR PH W/FS M5x14 206 | 000-0410-S M SCR PH W/S M4x10

207001-0508M SCR FH M5x8
208028-0003SET SCR PH SPCL M3x8
203039-0102CRG BLT M8x45
210059-0017HEX NUT M12
211050-0008HEX NUT M8

212 | 054-0005 U NUT Ms

213054-0006U NUT M6

214 | 029-0129 HEX SKT H CAP SCR BLK M6x25

215006-3525W SCR FH 3.5x25
21606-0030SPR WSHR M12

217 — | 061-0008 SPR WSHR M8

218061-0006SPR WSHR M6
219061-0005SPR WSHR M5

220 | 060-0006 FLT WSHR M6 221 | 069-0106 FLT WSHR 4.4-12x1.6

222060-0004FLT WSHR M4
223060-0008FLT WSHR M8

224 — | 001-0306 M SCR FH M3x6

225069-0109FLT WSHR 8.2-15x0.1

226 | 090-0012 SCREW LOCK 227 | 090-0013 GREASE

228000-0416-FSM SCR PH W/FS M4x16
229054-0004U NUT M4
r230000-0525-FSM SCR PH W/FS M5x25

~20-

Page 24

ASSY HANDLE U/R (GPD-20001) (D-7/8)

ITEM NO. PART NO. DESCRIPTION NOTE

231028-0012SET SCR CH SPCL M5x12
301600-5879-10| CONN HANDLE EXT
302SGB-4034-13WIRE HARN ANGLE VR

211-5282-03WH| CONN PLUG 9090 03P-WH

303 SGB-4034-14 | WIRE HARN ACCELE & BRAKE VR

211-5274-04RE | CONN PLUG AMP MINI 04P-RE 304 SGB-4034-15 | WIRE HARN SHIFT SW 211-5274—-03BL | CONN PLUG AMP MINI 03P-BL 280-0472 FASTON RCPT 110 305 SGB-4034-16 | WIRE HARN START SW

211-5274—04WH| CONN PLUG AMP MINI 04P-WH

280-0472 FASTON RCPT 110 601-5904 ONE TOUCH SLEEVE 110 306 SGB-4034-22 | WIRE HARN EARTH HANDLE 11-5282-01GR | CONN PLUG 9090 01P-GR —<4 211-0167 TERM LUG RND ID5

i307211-5276CONN PIN AMP MINI AWG 26-22
308211-5277CONN PIN AMP MINI AWG 22-18
309211-8284CONN PIN 9090 AWG 18-24
310211-5285CONN PIN 9090 AWG 14-20
311280-0425CORD CLAMP 210
312280-5008CORD CLAMP #15
313| 601-0460TIE BELT 85mm

211-5275-03BL | CONN CAP AMP MINI 03P-BL 211-5275-O4RE ) CONN CAP AMP MIN! 04P-RE

Page 25

ASSY HANDLE U/R (GPD-20001) (D-8/8)

ITEM NO, PART NO. DESCRIPTION

NOTE

211-5275-04WH CONN CAP AMP MINI 04P—WH

a

~22-

Page 26

GREEN ORIVE

QLU CUT OFF HORIZ SIZE GREEN CUT OFF

REO ORIVE REO CUT OFF HORIZ RASTER POSITION (7 ;— FUSE lowes TPS 4 TP4 u TP3 A HV BLU ORIVE is A sHUT “S pown xP i i} g

HORIZ VIDEO SHIFT +H. SYNC HORIZ HOLO +V. SYNC VERT RASTER POS GND

VERT SIZE VERT HOLD BRIGHTNESS

BLUE BLUE DRIVE cuT OFF GRN DRIVE GREEN son cut OFF HORIZ RASTER RED ORIVE POSITION

FUSE

x TPS TP4 TP3 t HV SHUTa “S pown t 4

NO

" +H. SYNC

+V. SYNC VERT RASTER POS GND

VERT SIZE VERT HOLO ®RIGHTNESS CONTRAST

MONITOR ADJUSTMENTS

Page 27

TEST MODE

The main purposes of these tests are to check the operations of the game boards, to find defects if any, to adjust the monitor colors properly, and to make sure the sounds are produced satisfactorily.

  • Selection of Test Items
  • INDIVIDUAL

MEMORY TEST INPUT TEST OUTPUT TEST SOUND TEST Cc. R.T, TEST DIP SW. ASSIGNMENTS BOOKKEEPING BACKUP RAM CLEAR COM. BOARD TEST EXIT

SELECT BY SHIFT SW. PRESS TEST SW. /

  • By pushing the TEST SW, the following test item menu can be displayed.
  • Push the SHIFT SW to move the arrow mark ">" downward. Bring the ">" mark to the desired TEST item and push the

TEST SW again.

  • When the test has been completed, move the "—>" mark to EXIT and push the TEST SW.
Page 28
  • Test Items and Details
  • Memory Test: To check if the on-board Memory IC's and

Custom IC's are normal or not. If the IC is

normal, "GOOD" is indicated and if it is not

normal, "BAD" will be displayed.

an MEMORY TEST >

qc, Ic,

Ic. Ic.

Ic. ic.

Ic, Ic.

  • * ROMS TEST * * 20 GOOD IC, 21 GOOD IC. 58 GOOD 29 GOOD IC. 30 GOOD IC. 63 GOOD
  • * RAMS TEST * * 22 GOOD IC. 31 GOOD IC. 38 GOOD 23 GOOD IC. 32 GOOD IC. 39 GOOD

55 GOOD IC. 60 GOOD IC. 125 GOOD 56 GOOD IC. 61 GOOD IC. 126 GOOD

132 GOOD IC. 134 GOOD IC. 150 GOOD 133 GOOD 1C.135 GOOD IC. 151 GOOD

%* %& CUSTOM IC TEST * *« IC, 30 GOOD IC. 37 GOOD IC. 53 GOOD IC. 107 GOOD IC, 108 GOOD

When the test has been completed, push the TEST Sw,

  • Input Test: To check the condition of each switch and

potentiometers.

INPUT TEST

® @ COIN #1 OFF START OFF @ sw COIN #2 OFF SERVICE OFF @ ON/OFF condition

  • POTENTIOMETER SHIFT A OFF

SHIFT B OFF @ CURRENT VALUE

@ ® (HEX ADECIMAL ) BANK 80H

ACCEL CCH

EAH Ke

Page 29

Oo Operate the dip switches. When "ON" is indicated at the right side of a certain tested item, the item is OK.

o If the data value increases when the handle is inclined to the right, or decreases when it is inclined to the left, the testing is OK (the data is indicated in hexadecimal values), Make adjustment in a manner so that in the static condition, the value shows 80H (within the range of 7CH~ 84H).

¢ If the data value decreases, becomes CCH + 04H (C8H~DOH) and becomes under 50H, when, respectively, the ACCELERATOR is applied, released and fully opened; then it is satisfactory.

+ If the data value decreases, becomes ECH + 04H (E8H~FOH ) and becomes under 70H, when, repectively, the BRAKE is applied, released and fully applied; then it is satisfactory.

OUTPUT TEST

DIAGNOSTIC VER. 1.00 OUTPUT TEST

START LAMP TEST

PUSH TEST BUTTON TO EXIT J

If the START LAMP lights up, it is functioning properly. When the test has been completed, push the TEST SW.

Page 30
  • SOUND TEST

This test is to check sounds. By using the SHIFT SW, bring

the "+" mark to the desired Test Item and push the START SW.

SOUND TEST

—1. MUSIC

  • EFFECT SOUND 1
  • EFFECT SOUND 2

4, VOICE

  • ENGINE SOUND

SELECT BY SHIFT SW. PRESS START SW, 7

Push the START SW to change to next page.

(— MUSIC

SELECT BY SHIFT PRESS START SW. / —1. OPENING 10. 2.GOAL i.

  • QUALIFY 12. 4, AUTOMATIC 13.
  • MANUAL 14.
  • LINK GAME 15.
  • TITLE 16. 8.NAME ENTRY 12. 9.GAME OVER 1 18. GAME OVER 2 LINK WIN 7 LINK LOSE 1 LINK LOSE 2

EXIT

sw. The test incorporates tests for 13 kinds of B.G.M., 33 kinds of SOUND EFFECTs and 11 kinds of VOICEs and ENGINE SOUNDs.

When the test has been completed, push the TEST SW.

Page 31
  • CRT TEST

(Sa

RED

GREEN

BLUE

BRIGHT

  • RED, GREEN, BLUE Ss

The color becomes darker from the left to the right.

+ BRIGHT

The color becomes darker from the left to the right.

  • DIP SWITCH ASSIGNMENTS Displays the condition of DIP SW A and B.

For details, see the page(s) explaining the DIP SW.

DIP SWITCH ASSIGNMENTS

1 2 3 4 5 6 7 8 DIP SW. A OFF OFF OFF OFF OFF OFF OFF OFF DIP SW. B OFF OFF OFF OFF OFF OFF OFF OFF

+ A1234 COIN SW #1 1COIN 1 CREDIT + A5678 COIN SW #2 1 COIN 1 CREDIT +Bl2 9 CABINET TYPE RIDE ON + B3 NO USE + Ba ID NO. 1 (MAIN) + BS ADVERTISE SOUND ON + B6 NO USE GAME DIFFICULTY NORMAL DIP SW. A

COIN SW SETTING

DIP SW. B

SETTING OF THE GAME

DIFFICULTY

When the test has been completed,

push the TEST SW.

Page 32
  • BOOKKEEPING

Page 1: Indicates the record of the number of coins and

credits.

  • of BOOKKEEPING

COIN CHUTE 1 COIN CHUTE 2 COIN CREDITS SERVICE CREDITS TOTAL CREDITS 6eeee ococooo

e TOTAL TIME 00HOO0MO00S

Lo PRESS START SW./ _ @ Usage frequency of Coin Chute 1 @ Usage frequency of Coin Chute 2 @ Number of Coin Credits @ Number of SERVICE CREDITS ® Total Number of Credits © Total time during which the machine is energized.

Push the START SW to change to Page 2.

o Page 2: Indicates the record of game time distribution,

a — BOOKKEEPING

NUMBER OF GAMES0®D
AVR. SCORE0@
TOP SCORE0@
LOW SCORE0@

GAME TIME

TOTAL00HOOMO0S9
AVERAGE00HO00MO00S©
LONGEST00HOOMOOS@

PRESS START SW./ Lo _ @® Number of Games @® Average score @ Highest score @ Lowest score ® Total game hours © The longest game time

Push the START SW to change to page 3.

Page 33

¢ Displays the COURSE RECORD, number of AUTOMATIC / MANUAL game plays, and the DATA of by-lap GAME OVER.

BOOKKEEPING @ COURSE RECORD

COURSE REC.ooMoosooD@® Number of AUTOMATIC game pla

AUTOMATIC Q plays

MANUALRy@ Number of MANUAL game plays
LAP 1@@® Number of 1 lap GAME OVER
LAP 23® Number of 2 laps GAME OVER
LAP 3©© Number of 3 laps GAME OVER
LAP 4Q® Number of 4 laps GAME OVER
GOAL®® Number of GOAL

PRESS START SW./

Push the START SW to change to Page 1. When the test has been

completed, push the TEST sw.

  • BACKUP RAM CLEAR

In this test, the content of the BOOKKEEPING data can be

cleared. When desiring to clear the data, bring the ">" mark to "YES" by using the START SW and push the TEST SW, and when not desiring to clear, bring the ">" mark to "NO" by using the START SW and push the TEST SW.

BACKUP RAM CLEAR xo When BACKUP RAM clear is —> YES finished. “COMPLETED” will

be shown on the screen.

SELECT BY SHIFT SW. PRESS TEST SW. /# SN

Page 34
  • COM. BOARD TEST

+ In the COMMUNICATION BOARD TEST mode, the COM. BOARD

(837-7273) check is performed. Carry out the test for both PLAYER 1 and 2 simultaneously.

COM. BOARD TEST

COM. BOARD GOOD

+ If the COM. BOARD is satisfactory, “COM. BOARD GOOD” will be displayed.

When the test has been completed, push the TEST SW.

(10)* To end the TEST mode, select “EXIT” on the MENU screen and

press the TEST SW.

The TEST mode ends with

“END OF DIAGNOSTICS”

displayed on the screen. END OF DIAGNOSTIC

L

Page 35

DIP SWITCH

PLAYER 2 PLAYER 1

DIP SWB

COIN/CREDIT OPTION SW. SETTING DIP SW. A

1727374Tse[7]28 ]

1 COIN 1 CREDIT | OFF| OFF|OFF| OFF | OFF| OFF| OFF| OFF 1 COIN 2 CREDITS | ON | OFF|OFF| OFF/ON | OFF|OFF| OFF 1 COIN 3 CREDITS | OFF|ON |OFF| OFF] OFF| ON | OFF| OFF

5 COINS1 CREDIT|ON |ON |OFF) OFF|ON | ON | OFF| OFF
6 COINS1 CREDIT|OFF|OFF|ON | OFF| OFF| OFF|ON | OFF

1 COIN 6 CREDITS |} ON | OFF|ON | OFF|ON | OFF| ON | OFF

2 COINS1 CREDIT|OFF|ON |ON | OFF| OFF] ON | ON | OFF
3.COINS1 CREDIT|ON | ON |ON | OFF] ON | ON |ON | OFF

4 COINS 1 CREDIT | OFF| OFF|OFF|ON | OFF| OFF | OFF] ON 2 COINS 3 CREDITS | ON | OFF|OFF|ON | ON | OFF| OFF] ON 2 COINS 1 CREDIT 3 COINS 2 CREDITS S COINS 3 CREDITS |OFF|ON |OFF| ON | OFF|ON | OFF | ON 6 COINS 4 CREDITS 2 COINS 1 CREDIT «COINS 3 GREDITs |ON |ON |OFF|ON | ON | ON | OFF] ON 1 COIN 1 CREDIT 2 COINS 2 CREDITS 3 COINS 3 CREDITS | OFF|OFF|ON | ON | OFF| OFF|ON | ON 4 COINS 4 CREDITS | 5 COINS 6 CREDITS 1 COIN 1 CREDIT 2 COINS 2 CREDITS 3 COINS 3 CREDITS |ON |OFF {ON |ON | ON | OFF|ON | ON 4 COINS 5 CREDITS 1 COIN 1 CREDIT 2 COINS 3 CREDITS |OFF|ON [ON |ON |OFF|ON |ON | ON FREE PLAY ON |ON [ON [ON |ON [ON {ON [ON

COIN Sw #1|_COIN SW #2

GAME OPTION SW. SETTING DIP SW. B

1 t2t37Taytstet7{s CABINET RIDE ON | OFF | OFF TYPE ‘UPRIGHT | ON | OFF | PLAYER1 (BLUE) OFF | PLAYER 2 (RED) ON ADVERTISE! ON NOT OFF [NOT

SOUND'_ OFFUSEDON _|USED

TNORMAL OFF | OFF

GAME1EASYON |OFF

| DIFFICULTY/HARD OFF | ON

L'HARDESTon_|ON

~32-

Page 36

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 37

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 38

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.