CATHODE RAY TOMES

Game Boy Color Repair Procedures

Game Boy Color (Nintendo, 1998) · Service Manual · 8 pages · 5 sections · original scan

Page 1

Hardware Overview

The major features and functions of the Game Boy Color are:

1. Central Processing Unit Custom 8 Bit Processor 127 x 8 bit internal Random Access Memory (RAM) Power up display program contained with internal Read Only Memory (ROM) Produces display signals for up to 52 different colors Stereo sound generation ¢ 16,384 Bytes of Video RAM for background graphics and text memory map

Sound Output e Audio power amplifier IC to drive outputs e Stereo sound provided to external jack for headphones (2mW) e¢ Mono sound provided to internal speaker (10mW)

Dot Matrix Red Green Blue (RGB) Liquid Crystal Display (LCD) e¢ Contains common and segment drivers ¢ 160 horizontal by 144 vertical dot resolution e LCD buffer amplifier (IR3E02) provides LCD bias voltage

Work RAM (127 X 8 bit) e Used to keep track of sprite locations, game score, game time, etc.

DC/DC Converter e Receives 3 VDC from two AA batteries or an AC Adapter e Provides 5 VDC for the CPU PCB operation e Provides -15 VDC and +13.6 VDC for the LCD operation

External Communication ¢ 6 pin I/O port for multiple player games or peripheral devices e Infrared transmitter and receiver for multiple player games

Page 2

Game Boy Color

Theory of Operation The operation of the Game Boy Color is similar to the original Game Boy and Game Boy Pocket, as it must still play Game Boy games. However, its faster CPU and extra RAM are used to play Game Boy Color dedicated games.

Power Supply Section - The DC/DC converter operates on a 3VDC input (2 AA batteries or an AC adapter) and provides the operating voltage for the Game Boy Color (5 VDC, - 15 VDC and 13.6 VDC). The minimum input voltage is 2 VDC and the minimum operating voltage is 4.6 VDC.

Controller Input Section - The controller uses a parallel/serial input to serial output shift register. The parallel inputs are connect to ground through open contact surfaces on the PCB. When an actuator is depressed, a contact pad is pressed against the surface causing the corresponding PI input line to be connected to ground. All control signals are sent and all controller functions are received by the CPU.

Display Section - The LCD has been changed to an RGB LCD display. The new display does not require contrast control, so it has been removed. The common and segment drivers are built in to the LCD.

System Timing Section - System timing include an oscillator and discrete components to supply a 8.4 MHz master clock signal to the CPU. The CPU uses the master clock to derive the control signals for the rest of the unit.

Note: The Sound Section, Game Pak Interface, and Program Section work the same as the Game Boy and Game Boy Pocket.
Page 3

Game Boy Color Repair Procedures Page 3

Block Diagram

LcD Driver HR-TFT 160 X 144 X RGB Dots

REG

LeD LoD

Headphone Driver Driver

Jack I +

+ Volume A

M Om Display RAM

P 64 Kbit e-Bit tI SRAM

Speaker Microcomputer

Display RAM 64 Kbit SRAM

Infrared Communications

Expanded WRAM S2Kbit X 8 SRAM SIO Terminal

Mask ROM

Program Batteries

DC Jack SRAM (for Back-up)

Power Switch Game Pak +13V +8V +3.3V-15V

Converter

Page 4

Game Boy Color Disassembly Procedures

1. Open the Game Boy Color by removing the six (6) brass screws (Y-Selftap Chromate P/N 21826). Two of the screws are under the battery cover.

Remove the rear housing, taking care not to damage the battery contacts as they slide through the housing.

Release the black tabs (see Figure 1) on the LCD ribbon connector (P2) by sliding them toward the top of the Game Boy Color.

Figure 1

Remove the three (3) screws (PHP Selftap Chromate P/N 34644) located below the 32 pin connector.

Lift out the PCB.

LCD Replacement

To remove the LCD screen, carefully twist the front housing to release the LCD from the LCD Gasket (see Figure 2).

Figure 2

Page 5
  • Carefully lift the LCD out of the housing.
Note: If the LCD is removed, replace the LCD Gasket (P/N 38894).
Caution: Insure the LCD viewing area is dust free before placing into the housing.
  • Assemble in reverse order.
Note: After replacing the rear housing, hold the Game Boy Color main unit, and insert the end of an angled probe into the center of the battery spring. Press firmly to crimp the raised metal tab.
Page 6

Exploded View

Page 7

Game Boy Color Repair Procedures Page 7

Item # Part # 21826 34637 34643 34644 34646 34686 35281 38884 38885 38886 38887 38888 38889 38890 38891 38892 38893 38894 38895 38896 38897 38898 38899 38900 38901 38902 Component Description Screw, M2 X 8.2 Y Self Tapping Contact, C-Pad MGB Plate, PCB Guard MGB Screw, M2 X 6 PHP Self-TapChro Speaker, MGB LBL, Consumer Service MGB Screw, M2 X 6 PHP Prec Tap Chro Actuator, A Button CGB Actuator, B Button CGB Actuator, C-Pad CBG Actuator, Power Switch CGB Actuator, Select/Start CGB Contact, A/B MGL Contact, Batt (W) CGB Cover, Batt CGB Grape Cover, LED CGB Cover, Screen CGB Gasket, Front Screen CGB Hsg. Front CGB Grape Hsg. Back CGB Grape LBL, Adjustment Cover Purple CG LBL, Model # CGB LBL, Serial # CG Barcode CGB LCD Unit, CGB Support, LCD CGB PCB, CGB-CPU Quantity Per Build

were

ee ee er Sry

Page 8

Game Boy Color Repair Procedures Page 8

Game Boy Color

Schematic