CATHODE RAY TOMES

Fax Manual Version 1.0

FAX (Exidy, 1983) · Manual · 69 pages · 33 sections · original scan

Page 1

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 2

FAX™

Operation and Service Manual 1st Edition

t

  • 1983 Exidy, Inc. Exidy Ireland 398 Java Drive, Sunnyvale, Gortlandroe Industrial Estate . California 94989-1271 Nenagh, County Tipperary Telephone: (48) 734-9416 Ireland Toll-free: (888) 538-8492 Telephone (@67) 32555 Telex: 357-499 (EXIDY MNTV) Telex: 70089 (EXDY EI)
Page 3

FOREWORD

Part One of this manual contains Preliminary Procedures, describing game inspection, installation, and checkout. Also, Adjustment Procedures are given for Power Supply, Audio Volume, and Operator Selectable Options.

Part Two, Modes of Operation, describes the four FAX™ modes: Automatic Self-Diagnostic Test Mode, Attract Mode, Game Play Mode, and Vanity Mode.

Appendix A contains game schematics, with a circuit description on each Page opposite.

Appendi.x B is the Illustrated Parts List. Parts are pointed out in the drawings and listed opposite each drawing.

Page 4

EXIDY FAX™M OPERATION AND SERVICE MANUAL

TABLE OF CONTENTS

I. PRELIMINARY PROCEDURES ...seeccccccsccccccerevees L

A. GAME INSPECTION ...

  • Filing a Claim ..
  • Visual Inspection ......

B. INSTALLATION wcscccccccccee

C. PRELIMINARY CHECKOUT PROCEDURE «-csssceeveess N

De ADJUSTMENTS .rcccccccrcccccccvecsccecresccece

  • Power Supply Information and Adjustments .
  • Audio Board Adjustments ....seees
  • Operator Selectable Options .....++. a. Coinage b. Game Length / Time Bonus c. Bonus Time Point Level www

TI. MODES OF OPERATION ...cccccvecccccevescceceveses ©

A. AUTOMATIC SELF-TEST MODE ....

  • Logic Diagnostic Tests . a. The RAM Test b. The EPROM Test
  • Audio Diagnostic Tests ..ssessessees
  • Control and Color Diagnostic Tests..

B. THE ATTRACT MODE .ecuesoeee eeeeeees F

C. GAME PLAY MODE .ccsccccvecsccccvccsccssrenes 1D

Dz. VANITY MODE coccsscccceccccccccsccecvecceess 1D

APPENDIX A: SCHEMATICS

Page 1: GAME LOGIC .. seveccccees AHL

Master Oscillator, Element (Horizontal) Counters, Line (Vertical) Counters, Screen RAM Addresses, Coin Input Decoding, Hardware Generated Line Positioning Proms, Blanking and Video Clocking

Page 5

Page 22 LOGiC cccccccccccccccccccscccccceeeees AMZ Screen Controller PROM, Screen RAM, Character Image Storage, PROM Power and Signal Selection, Character Generator Output Shift Register

Page 3: LOgic esccccccccccccccccccseccccsesces AMS Character Generator Image Storage, Plane

Interface Board

Page 42 Logic cecceeccccscccccccsccvccscoesees AMA The 6502 Microprocessor, Power-on Reset circuit, Processor Workspace RAM, Main Address Decoding

Page 5: Logic sccccessccccccccccccccccccescess AMS Program Memory, PROM Address Selection, Memory Device "Personality" Selection

Page 62 LOGIC seccceccccccesccccccccescesceees AG Moving Object Horizontal Position, Moving Object Vertical Position Counters, "Write Moving Object" Decoding, Color Interface Output

Page 72 LOGic cresessccccccccccccccccccceveses AMT Moving Object Multiplexing, Moving Objects Image PROM, Moving Object Video Output Shift Registers, Moving Objects Shift Register Load Logic, Moving Object Shift Register Control Logic, Memory Device Personality Configuration

Page 8: LOgic coscccccccreccccceccceccccsceses AB

Interrupt Status Latch , Option Switch Port,

Control Inputs Port, Moving Image Latch, Audio Board Port, Control Port Latch, I/O Decoding

Page 9: Memory and Expansion I/O Board ...++.. A-9

AUDIO/COLOR PCB-GENERAL DESCRIPTION ..esseeees A-1G Page 1: AUGLO/COlOr. eee eeseccececcecccceceees APLL Logic and Power Interface, Communications and Address Decoding

Page 2: Audio/Color ceeescccsceccccccevesceees AML2 6592 Microprocessor, Peripheral Interface Adapters, Address Decoding, Music Generator, Master Oscillator, Program Memory, Output Filter

Page 3: Audio/Color .sececcecescccceccccceecee AMlZ Clock Manipulation and Noise Generation Circuit, Amplitude Modulation Control, Output Summation and Special Effects, Volume Control

Page 6

Page 4: AudGiO/COLOL..seeeseceverecccvccccecess AMl4 Summing Amplifier, Integrator and Audio Power Amplifier, Volume controls

Page 5: AUGLiO/COLOL.+.eerecesesccccececeescees ALS Pattern Character Color Division, Priority Encoder, Color Data Latches, Color Selection Multiplexers, Video and Sync Signal Polarity Selection, Final Video Output Resychronization

Wiring Harness Diagrams/Schematics

Block Diagrams, A.C. Power and Monitor, Power Supply Assy,Main Harness, Control Panel Harness, Coin Door Harness, Power Supply Schematic, Game Monitor Schematic.

APPENDIX B: ILLUSTRATED PARTS LIST......++eeeeeeeeee Bol

I.

J. FAXTM POWER SUPPLY ASSY.......sseeeeeeeeeees BS

COIN DOOR ASSEMBLY .eeeeseecceeccseeeveeeees BS LOGIC AND AUDIO BOARD ASSEMBLY ..++eeeeeeees BO

PRINTED CIRCUIT, UNIVERSAL POWER SUPPLY .... B-7

LOGIC BOARD ..cceeeeecescsscsceccseeseeseses BB

AUDIO/COLOR BOARD ASSEMBLY ....eseseeseceees BRD

PLANE INTERFACE BOARD ..eceesssescecesseees Bl

MEMORY & I/O EXPANSION BOARD...+sseeeeesees Bell

Page 7

COPYRIGHT

Copyright (c) 1983 by Exidy Inc. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored ina retrieval system, or translated into any language in any form, or by any means without the prior written permission of Exidy, Inc. 398 Java Drive, Sunnyvale, California 94989.

DISCLAIMER

Exidy Inc. makes no representations or warranties with respect to the contents hereof and specifically disclaims any implied warranties of merchantibility or fitness for any particular purpose. Further, Exidy Inc. reserves the right to revise this publication from time to time in the content hereof without obligation of Exidy Inc. to notify any person of such revision or changes.

‘TRADEMARKS

FAXx™ is a trademark of Exidy Inc.

WARNING

This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual, may cause interference to radio comminications. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of FCC Rules which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment ina residential area is likely to cause interference in which case the user at his own expense will be required to take whatever measure may be required to correct the interference.

QUESTIONS

Exidy encourages technicians to use the toll-free customer service hotline for any questions they may have regarding FAX™, ‘That number is (800) 538-8492.

Page 8

I.

PRELIMINARY PROCEDURES

A. GAME INSPECTION

All Exidy equipment is carefully packaged in well-padded cardboard containers to prevent damage during shipment. Before signing the delivery receipt, you should follow this procedure:

1.

4.

1. Check for obvious damage and make certain that the physical piece count of the shipment matches the piece count on the bill of lading. These two procedures should always be done before signing the delivery receipt.

Shortages and/or obvious damage to the packaging on any given shipment should be noted in writing on the delivery receipt before signing for the delivery.

If concealed damage is suspected on any shipment, those packages believed to contain the damaged goods should be opened in the presence of the delivery driver. If the goods have sustained concealed damage, a description of said damage should be noted in writing on the delivery receipt before signing for the delivery.

Never apply power to any game with noticeable damage.

Filing a Claim

To file a claim, follow this procedure:

1. Any and all damaged freight, including packaging, should be retained by the consignee until a physical inspection of said freight can be made by a representative of the carrier involved.

The Claims Manager for the carrier involved should be notified as soon as possible, after the damaged goods are received. Preferably, the carrier's Claims Manager should be notified within forty-eight (48) hours of receipt of the goods by the consignee.

If warranted, a written claim should be filed with the carrier involved. A detailed description of the damage(s) should be provided and copies of all supporting documents, including bill of lading and/or delivery receipt, inspection report, and invoice, should be attached.

The sooner a claim is filed, the better for all parties concerned. The carrier against which a claim is filed is required, by law, to respond to (acknowledge) that claim within thirty (30) days of receiving same and mst reach a final disposition in the matter within one hundred twenty (120) days.

Visual Inspection

Remove the rear and front access doors with the appropriate packaged key.

Examine each major and electrical component thoroughly for scrapes, dents, broken or missing parts and loose or missing screws.

Check for loose cable connectors.

Page 9
  • Visually verify that all the integrated circuit devices (IC's) plugged into sockets are properly seated and that no IC pins are bent or misaligned.

If you find any damage during this inspection, file a claim with the carrier. Send a complete report of the damage to Exidy Inc.

B. INSTALLATION

Planning the location of the game should involve both physical and electrical considerations. Such physical considerations concern the placement of the equipment with respect to these clearances:

Height: 55.58 inches, 149.2 cm. Width: 37.25 inches, 94.5 cm. Depth: 24.88 inches, 61.8 cm.

An indoor, relatively dust-free environment is necessary, with proper conditions required of any electrical device. Electrical considerations include availability of an AC outlet with the correct voltage and frequency. You should consider the working space required for technicians and operators including access to the rear of the game.

NOTE: The cabinet must be within seven feet of an AC outlet. Be certain that a ground jack or terminal is available at the outlet.
CAUTION: DO NOT remove the AC ground prong from the plug. Doing so voids your warranty!

C. PRELIMINARY CHECKOUT PROCEDURE

After properly installing FAX™, we suggest following this procedure to check its operation:

  • Connect the AC power plug into the AC outlet.
  • Once powered up, after five seconds of silence, a quick beep sounding like an organ chord, isheard. This is part of the Exidy AudioDiagnosticTest. A single beep indicates all is well with the audio board. If more than one beep is heard, refer to Part II, Automatic Diagnostic Test Mode.
  • Allow 8-18 seconds to pass for the CRT to warm up.
  • Observe the TV monitor display. After Exidy Diagnostic Test are completed assure the correct attract mode is present on the screen, as described in Part II B, Attract Mode. If the Fi display is incorrect, contact Exidy‘s Customer Service Department.
  • Insert the appropriate coin or token into each of the coin slots. The message in the attract mode will flash the following lines:
Page 10

FAX™M

CREDITS

Press Start

One or Two Players

A ONE PLAYER CHALLENGE

A TWO PLAYER RACE

depending on the number of coins dropped into the coin slot, or the number of credits awarded for each coin..

  • Press one or two player start and play the game to verify that all screen images are displayed as described in Part II C, Game Play Mode.

If assistance or repairs are necessary, contact the Exidy‘s Customer Service Department, (828) 538-8492.

D. ADJUSTMENTS

  • Power Supply Information and Adjustments

All DC Power required to operate FAX™ is supplied in the Exidy Power Supply Module. These supply outputs are as follows:

+5v DC@6 amps

-5v DC (Not ysed) @ 1 amp

+12v DC (AI),@3 amps
+12v De (Lo)!@1 amp
aR8la

amp

; (HI) refers to "high current"

(LO) refers to “low current"

CAUTION: Only certified technicians should make adjustments on all components of FAX, Only the +5v DC is adjustable. This must be adjusted to:

+5.@0v DC +/- .lv

as measured on the Main Logic PCB near the 6582 Microprocessor (location 2A).

  • Andio Board Adjustments

The following drawing points out the three individual audio adjustments and the location of the DIP switch. The audio board rides piggyback on the logic board, mounted on the back wall of the game.

Page 11

fae VOLUME SPECIAL EFFECTS 7 VOLUME

th Music VOLUME

  • Operator Selectable Options

FAXT™ has several switch selectable options controlled by an 8-position DIP switch located on the main logic board at position 16A. This switch is accessible through the left front door of the game.

FAX™ is shipped with the DIP switch already set for optimum dollar return, that is 48 seconds game clock 3:12 play time with 36 seconds bonus clock time at 13,988 point level. Actual game time play for the average player will be aproximately 2 to 4 times the game clock time as the game clock (bottom of screen) starts and stops at various times throughout the play of a game. The game clock starts when the answer to the first question appears on the screen, and stops when a player (both players in a two player game) selects an answer, right or wrong. This sequence is repeated for all questions. Should you decide to change the settings, you may select any of the following options by setting the proper switches accordingly:

Page 12
a. COINAGESwitchSwitch

4 5

F/s1 Coin - 1 CreditOFFOFF

2 Coins - 1 Credit OFF ON

1 Coin - 2 CreditsonOFF

1 Coin - 4 Credits on ON 1 Coin - 3 Credits OFF fons

OR 2 Coins - 7 Credits

1 Coin in Left Slot- OFF OFF

1 Credit, 1 Coin in Right Slot- 5 Credits”

1 Coin in Left Slot- fox OFF

1 Credit, 1 Coin in | Right Slot- 4 Credits

2 Coins in Left Slot- ON ON

1 Credit,1 Coin in Right Slot- 3 Credits*

b. GAME TIMESSwitchSwitch
GameApprox.Bonus
Clock TimePlay TimeTime67
3322:08224OFFOFF
F/s2483212336aNOFF
1:044:16348OFFOn
1:124:481:84ONON
c. BONUS TIMESwitchSwitch
(Extra time awarded23

when selectable number of points are made. Maximum of 2).

8,200OFFOFF
P/s13,980foOFF
18,808OFFON
25, 088ONON
  • Requires dual harness. F/S=factory setting. switch 1 is not used adn should be off. Switch

OFF

OFF

Page 13

FREEPLAY: For those wishing to demonstrate FAXTM, a freeplay mode may be achieved by turning switches 2 through 8 ON.

II. MODES OF OPERATION

A. AUTOMATIC SELF-TEST MODE

FAX™ automatically tests the logic data and audio boards on power up. To run the Control and Color Test, activate the coin switch while powering up.

You may bypass both diagnostic modes by depressing either the one or two player start button while powering up. After 8 seconds of the message "STAND BY VERSION X", (where X is a number representing the software version) the Attract Mode appears.

  • LOGIC DIAGNOSTIC TESTS

a. The RAM Test

When FAX™ is first turned on, a processor and video RAMtest are done. If the RAM passes, it goes immediately into the EPROM test, without a message indicating it passed the RAM test.

If a RAMChip fails, an attempt is made to indicate the RAM chip where a failure was detected. Since the screen depends on a properly functioning RAM, this indication may not be displayed. A failed RAM may be indicated by a digit from @ to 3 in every position on the screen. The code for these digits is as follows:

Number RAM chip Number Location

onto checkonon Plane
Screenon logicScreenInterface

board board

@4A,5A (2114)3Ul (6116)

1 7B,8B (2114)

2 9c (6116)

The RAM test cycles if the failure is persistent

Page 14

b. The EPROM Test If the RAM test passes, the EPROM test begins. The message "PROGRAM EPROM CRC TEST" first appears on the screen to indicate the FAX™ program logic Eproms are been tested. One by one, "X"*s appear on the screen. Each X indicates half of a 2732 EPROM, in locations 13A through 6A, on the logic board has passed the diagnostic test. Note that each EPROM is represented by two X‘s. To indicate the FAxt™ Questions and Answer Data Eprom‘s are been tested. After 16 X‘s appear the message "DATA EPROM CHECKSUM TEST" appears on the screen. Again X‘s will appear to indicate 2764 EPROMS in locations 1¢ through 8C, 1B through 8B and 1A through 8A on the MEMORY EXPANSION & I/O BOARD”, have passed the diagnostic test. Each EPROM is represented by one X with the first X assigned to 1C and the last to 8A.

If any failure is detected during the EPROM test, an alpha/numerical digit appears instead of "X" with a “BAD EPROM" message. The key for which chip to check is as follows:

DATA EPROM CHECKSUM TEST

8®123456789ABCDEFGHIJKLMN

lc 3c 5C 7C 1B 3B 5B 7B 1A 3A 5A 7A 2c 4c 6c 8& 2B 4B 6B 8B 2A 4A 6A 8A

PROGRAM EPROM CRC TEST

@1 23 45 67 89 AB CD EF 13A 12A 11A 180A 9A 8A 7A 6A

*NOTE: All locations may not be filled depending on the amount of memory required. (I.E. 7A and 8A are presently empty.)

Page 15
  • AUDIO DIAGNOSTIC TESTS

While the Logic Board tests are underway, the Audio board is also being checked.

Five seconds after power on, one or more quick beeps, like an organ chord, are heard. This is part of the Exidy Audio Diagnostic Test. The number of beeps that sound indicate different conditions of the Audio board. The following code is an indication only, of where to first check the Audio Board. Because this diagnostic test only evaluates certain components, other circuitry is relied upon for the test. Should this other circuitry fail, the diagnostic test may not, then, point directly to the failure. Please use the results of this test as a guideline for further troubleshooting.

The code is as follows:

@ beep: If no beeps are heard, along with a hum or random notes, this may indicate a failure in 3A and/or 7A, or volume control have been turned off.

1 beep: All audio hardware is OK. However, be sure to check the Attract Mode Cycle for a possible message to check the Audio Board. In occasional instances, this can occur. The message will further direct you.

2beeps: ZERO PAGE RAM failure. Check 6532 RAMI.O. Timer Array at location 7B on the audio board.

3 beeps: (will not occur)

4 beeps: ROM failure

5 beeps: INTERRUPT failure. Check 6532 at location 7B.

In addition, this message appears during the Attract Mode only if the Audio Board needs to be checked:

“AUDIO COMM ERROR" or "TEST ERROR"

  • OONTROL AND COLOR DIAGNOSTIC TESTS

If desired, you may test all player controls and screen colors for monitor adjustments To do so, activate either coin switch at power-up. The game then enters the Control/Color Test Mode. This mode lasts for 1@@ seconds to give you time to test and make adjustments. After that, the Attract Mode begins.

In the Control/Color Test Mode, the screen shows this pattern:

Page 16

au {+]-[-[-}-[-[-[-[-} wom [-]-] - | fan o for

The grid pattern tests your screen for any distortion or convergence.

The solid blocks of color (blue, white, green, and red) allow you to adjust the color. When either of the player control buttons (one player or two player) or coin switches (coin 1 coin 2) are activated, their name appears below the blue box. When any of the lettered answer buttons ("A" through "D" for player 1 or 2) are activated, their name appears below the blue and white boxes.

B. THE ATTRACT MODE

After FAXT™ goes through its automatic self-diagnostic test mode on power-up, a series of screen displays are shown repeatedly. The first screen identifies the game and manufacturer, along with credit information. The second screen gives game instructions. The third screen is the dean‘s list, with the initials and scores of the eight highest scoring players.

Page 17

The final screen shows the comparative progress display. The cycle then repeats.

C. GAME PLAY MODE

FAX™ is a timed trivia game of miltiple choice, YES/NO, and TRUE/FALSE questions for either one or two players. Naturally the object of the game is to correctly answer as many questions as possible and score as many points as possible. A player first selects one of the four categories and the difficulty level (choice of three). After each question appears on the screen, the possible answers will appear directly below. The player only has one chance to answer the question. He cannot change is mind once an answer is chosen. The quicker a question is answered correctly, the more points are scored. The game is played until time runs out. Bonus time is awarded for high scores. In a two player game both players play simultaneusly and the first correct answer wins the points.

D. VANITY MODE

Anytime a player's score exceeds one of the fifty current high scores, he is eligible to enter his initials in the Vanity Table. Only the top eight scores will be displayed in the Attract Mode. If both players of a two player game are record high scorers, the higher of the two is first invited to enter his initials. Todo so, he uses the A thru D buttons. Use the "A" or "B" button to run the alphabet letters up or down respectively. Once the desired letter appears enter it in by depressing either the "C" or "D" buttons. The game will return to the Attract Mode either after all the initials have been entered or after approximately 100 seconds have elapsed.

Page 18

APPENDIX A: SCHEMATICS

PAGE 1, GAME LOGIC PCB

  • Master Oscillator (1D)

From this oscillator all dynamic operations are derived, such as the processor clock, the main element and line counters, the shift register clocks, as well as all other forms of timing signals.

  • Element (Horizontal) Gounters (1C, iE, ZEY These components form the final stages of horizontal timing. All operations in this game requiring horizontal positioning or timing have their origin here.
Note that, beginning with signal HCLK (fram Clock Divide Counter 2D), there are 256 counts prior to setting signal E256 high. When this signal goes high, it indicates that the horizontal blanking

period is in progress At this time the

final counter (1E) is preloaded with a higher number than previously loaded. This creates a shorter count the second time around. The shorter count measures the retrace interval. When the retrace count is finished, the counter preloads with a lower number, establishing a longer count sequence again for “real time" sweep of the electron beam across the face of the CRT.

23) Line (Vertical) Counters (4F, 5F,

6E

These components form the entire vertical timing operation starting with a clock derived from horizontal timing. These counters count 256 times and then preload with a higher number, causing a shorter count the second time. This shorter count measures the vertical retrace interval. Note that signal L256, when high, indicates vertical planking is in progress. After the completion of the vertical retrace count, the counters once again preload with a lower number. This way they count 256 times during the sweep of the electron beam down the face of the CRT, allowing the horizontal timers to sweep one complete horizontal line for each count of the vertical counters. Thus, the electron beam reaches the bottom of the CRT, after completing 256 horizontal line sweeps. It then begins the vertical retrace count, and the whole cycle begins anew with the beam starting again at the top of the CRT.

  • Screen RAM Addresses (7D)

During the time the screen RAM is examined by the logic for output to the monitor screen, addresses must be applied to the screen RAM to count up at a rate corresponding to the image cells conceptually arranged on the screen ina 32 x 32 matrix. The counts used here, 4 fran the element counters, and 4 from the line counters, fulfill this timin

requirement. Theleastsignifican'

element count used (E8) represents an interval exactly eight times that of one element. The least significant line count used represents an interval

exactly eighttimesthatofone

horizontal line, or eight times a single line count. Dividing a 256 element line by 8 yields 32, and likewise dividing a 256 line vertical sweep by 8 yields 32. Thus the screen RAM address lines (RAMO through RAM9) count at a rate that creates 32 horizontal counts and 32 vertical counts as the electron beam sweeps the face of the CRT. This makes 1824 conceptual "image cells" into which can then be inserted images of 8 elements by 8 lines. For more information concerning shee im s. eyed to the

text forSof thelic

Schematic. tog

  • Coin Input Decoding (1H) Some models of FAX™ contain two separate
coininputsforspecialcoinage

applications. NOR ‘te 1H combines ese separate inputs, making signal SCOINT, which sets the interrupt flipflop (6E on page 8) when either coin input

becomesactive,thusforcingthe

microprocessor to jump to the interrupt service routine. This interrupt driven operation prevents ever missing a coin when inserted. However, this also means that when a game is first powered up, the coin input mist be inactive. If for some

reeen the oon input switch is enabled

attime o:rup, thecomes

with test pattern ilbgtratea an page e

  • Blanking and Video Clocking (5H)

Flip-flop 5H merely combines blanking and all other video.

Page 19

PAGE 2, GAME LOGIC PCB

  • Screen Controller PROM (6D)

This PROM controls the direction of data flow into and out of the screen RAM and character generator RAM. It prevents

timingerrorsand bussconflicts,

assuring that the microprocessor can write to either the screen or character generator RAM, or read back from either.

  • Screen RAM (7B, 8B)

The screen RAM is comprised of two 1024 x 4 static RAMs, configured to act as a single 1024 x 8 RAM. This creates a screen matrix of 32 horizontal by 32 vertical positions. A single byte code is stored in each of these positions to

representaparticularcharacter.

During “real time" (the time the CRT is being swept by the electron beam) these © character codes address the character generator RAM.

These character codes, when used as addresses, are combined with the three least significant line counts (Ll, L2, LA) to present to the character generator output shift register all the necessary data to form an 8 element wide by 8 line high character on the CRT, located within one of the 1024 positions mentioned immediately above; that is, the 32 horizontal by 32 vertical positions.

The screen, then, is a storage place for single byte codes that call up an 8 x 8 Character and place it into the

correspondingcharactercell. This

character is stored in the character generator RAM, shown on page 3 of the schematic.

  • Character Image Storage

Shown on this page are two PROMs (9%, 1@C). They could be used as a permanent. set of characters. However, FAX™ uses RAM instead, to increase the flexibility in character manipulation. This portion of RAM appears on page 3 of the Logic schematics.

  • PROM Power and Signal Selection (ieBy — —

This Dip Shunt configures the logic for different types of PROM devices. For FAXTM, however, this Dip Shunt is unnecessary due to the fact that RAM has been used rather than PROM.

  • Character Generator Output Shift Register (128)

Video from the character generator memory devices (RAM in the case of FAX™) is formed by this shift register as a byte of data that displays one line at a time from left to right on the CRI. This ultimately forms an 8 line high by 8 element wide character positioned on the screen according to the time it is presented to the shift register.

Output from this shift register are all the images seen on the screen except the lower body of the characters climbing the ladders.

Page 20

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 21

SCREEY Gnip ceurcT and BUSS GeECTION VECODING PROM 2 2) ahs be 3 7

16049) l2_csor3s =te
SaPrecerBe 31s
2] ass; [eeseeeWP yo% eces:os ©] seas DF
Ss seseotsbe 7 °538° bs
a sereeo 220or =‘e
z ie SiTeeba =1
le Swe a,BP [screen ram®3eceso ia |
FEES” exp tafspt Save q(ur cave Sroence)Saree

= vorio I

4s 258he‘| 2vas 22!
xs vehe7 iwas 2s2vor 1a1s BE 12 seavin
ra =cofeo12 15 anaTtevoo 12CR
es= ttcyi Tt fwaeisws
is hsen-a|'S32* fews 3) 616vos 10
ia] ee!ane*=vasreyvos sCHARACTER
=>aer@vas 5mWoe 4] tasgePa
x333wae«8cvorLpee cur Por:
paceTRL" leaa3wooSWET REGISTER
soreco:
laoBEBO doelax
esaismo [E]ot-
esCES TE cefeds
hidwievera.__21|pee
a onesaosere0 28sscuf > [or

i. ves ios =

taza+5ai+
ca aadie?econoL.
73} [~2t
sess8 |7t22/70 pyawel2
°z25] INTERNE
Fasewo 2 fa LeeS
Bayreie=rc
+meeve$=
=Faiz |ai
$ie53 gapm ES
a5See
wean a |*2as@) Foe [s
S8_Sdeey7>
woe oh==

secceot | = texecie| rahe escorted 07 zh Ble ra

be 37varzi_ ai
a)Yewar20— 29]
bas5rare]

ae ftseas [is ee

o Gi.CHAPAETER ance

a Sraease SEBO B dee Leese SSeS gene See Fase 3 for je ANoraghe SAM ds0d —— For Paasenn gente rd clesgeable imagery Pree 4 S10IKL ‘ SELeeTIO44 ' \ 502 GAME LOGIC PCB

:=oee l=
DIP SHUNTDEQHARACTER GENERATOR

TARE QUT RESTATE m zore 7660801

Page 22

PAGE 3, PLANE INTERFACE BOARD Image Storage RAM

  • Character Generator Image Storage RAM and Plane Interface Board (9C, UL)

These two RAMs, when used in this configuration, act as a 4096 x 8 bit RAM. The two color images placed on the screen are stored in this RAM by the microprocessor, according to the game program. In this RAM images are established, altered, shifted slightly, and even replaced with a new set, if required by the program. When called by the logic to do so, the RAM presents, to the character generator shift register, a single byte, repre—senting one line of a particular image. Each image is composed of 8 lines of data, each line is one byte-wide. Thus, 256 images of 8 x 8 bits can be stored here simultaneously and "called up" by the screen RAM to be displayed on the CRT in any of the 1924 character cell positions. A single byte code, stored in the screen RAM, calls up a _= character. The character may change or move by replacing the single byte code in the screen RAM, or by altering the data in the character generator RAM which forms the image.

Page 23

8 7 6 5 Y 4 3 2 1

[A | Baca

ap * B t

TO LOCK S a A me pang pI ea a rr| = ss | =n i | =. | P Z —— 9} vs

a x are R, voce eon

  • eA i os eee a Zuwmon = ENTERRRE ~“, = == 1G" |e L2 77- coe | Di aaa E Es
Page 24

PAGE 4, GAME LOGIC PCB

  • ‘The 6502 Microprocessor (2A)

For detailed information concerning this microprocessor, refer to the MOSTEK publication, 65@@-10A, MCS Microcomputer Family Hardware Manual.

One feature that should be mentioned here, however, is that this microprocessor has “memory-mapped 1/0". This means that all ports interfacing to peripherals of any type must be located within the normal memory map, with no duplication of addresses, since no instructions are specifically oriented toward I/O operations.

  • Power-on Reset circuit (connected to 2B pin 40)

When power is first applied to a game, a particular sequence of events must occur to set up all logic conditions. If this sequence is broken for whatever reason, the microprocessor may become confused, and the game will not start and run.

This sequence is accomplished when the reset line to the microprocessor is the last line allowed to reach a "high" logic level. The Power-on reset circuit makes sure this occurs by utilizing the charge time of an RC network as a delay.

If any kind of power interruption occurs during normal game play, the power-on reset circuit insures that the microprocessor is reset. This alleviates confusing the microprocessor, while it also recreates the original power-on sequence.

  • Processor Workspace RAM (4A, 5A)

The RAM, or workspace, consists of the lowest 1024 bytes of memory and can be divided into three separate sections due to distinctly different functions.

The lowest 256 bytes (@ to FF Hexadecimal) is reserved for special software register operations, and is called "zero page". The processor uses this area to store dynamic variables. For details of this type of operation, refer to 6502 technical literature regarding "Zero Page Addressing".

The next higher 256 bytes (100 to 1FF Hex) is reserved for the 6502 stack. The processor stores return addresses in the stack when interrupted or called to execute a subroutine. The game program may also request the processor to store other kinds of information here for later retrieval.

The next higher 512 bytes (200 to 3FF Hex) are used as a scratchpad area. Miscellaneous calculations and their results are temporarily stored here. If an error in this RAM occurs, the screen will not retain the condition that existed prior to losing the last turn, or between players.

4. Main Address Decoding (5C, 5D, 5E)

This circuit is the first stage of the address line decoding necessary to organize the memory map; that is, it Places specific functions or devices within generalized blocks of the memory map, grouped by function.

Page 25

PAGE 5, GAME LOGIC PCB

1. Program Memory (6A through 13A)

These memory devices are 2732 EPROMS.

Note that four of the lines to each memory device (PCSO through PCS7, PAP19, PAP20, PAP21) are programmable through jumper configurations located at 4B and 11B. This allows different memory devices to be used and/or facilitates interconnection to the memory expansion PCB (if used).
  • PROM Address Selection (4B, 5B)

This is a second stage of address decoding, used to select each individual memory device when addressed. Signal ROMSEL (from page 4 Main Address Decoding) selects the Program Memory devices in general, and jumper 4B, together with decoder 5B further defines an address to a particular memory device.

  • Memory Device "Personality" Selection (11B)

The dip shunt, or jumpers block, alters control signal configuration to the program memory devices. This allows the use of alternate size EPROMS and/or those created by different manufacturers whose control signal pinouts may not be identical to one another.

Page 26

PAGE 6, GAME LOGIC PCB

  • Moving Object Horizontal Position Counters (13F, 15F, 14F, 16F)

Counters 13F and 15F form a byte-wide counter which horizontally positions Moving Object 1 on the screen. These counters are preloaded to a certain value by the microprocessor during Vertical Retrace time. Then, after each occurrence of the Horizontal Sync, they begin to count. The count outputs AND‘ed through 15E give rise to signal MIHW, the Horizontal Position Window for Moving Object 1. Counters 14F and 16F are the equivalent circuit for Moving Object 2.

  • Moving Object Vertical Position Counters (16E, 125, 1£, 132)

Counters 16E and 12E form a byte-wide counter which positions Moving Object 1 vertically on the screen. These counters are preloaded to a certain value by the microprocessor during Vertical Retrace time. Then, after each occurrence of Vertical sync, they begin counting. The four count outputs of the least significant of these two counters (MLL1, M1L2, MIL3, MLL4) are sent to the moving object image PROM to specify which line of the image is presently being displayed. The AND'ed outputs of the second counter give rise to signal MlW, the Vertical Position Window for Moving Object 1. Counters 11E and 13E are the equivalent circuit for Moving Object 2.

  • “Write Moving Object" Decoding (6F, 16H, 5E, 3F)

Consists of two distinctly different functions. 6F and 16H form the circuit that generates the load pulses for the moving object position counters, while 5E and 3F simply prevent the counters fram counting during blanking.

  • Color Interface Output (16B)

This is a 14 pin DIP socket used as the connector interface to the color selection circuitry, located on the audio PCB. The signals and their functions are listed below:

Pin #

1 5SRLOAD = Shift Register Load Pulse (Neg. True)

2CBLB= Composite Blanking
3CSYNC= Composite Sync
4SCVID= Composite Video (Neg. True)
55SCLK= Shift Register Clock (Neg. True)
6HSYNC= Horizontal Sync

7 GND

8VSYNC= Vertical Sync

9 5MO2VID = Moving Object 2 Video (Neg. True) 18 S5MO1VID = Moving Object 1 Video (Neg. True)

11DBDIR= Character Generator Address Line 9

12 CSSR = NOT USED ON FAX™

13VD7A1®= Character Generator Address Line 10

+5V

Page 27

PAGE 7, GAME LOGIC PCB

  • Moving Object Multiplexing (14A, 148)

These two multiplexers pass information to the moving objects image PROM. They contain two codes: one determines which image should appear, and the other specifies which line of that image is to be displayed.

The data passed alternates between data for Moving Object 1 and Moving Object 2, depending on the state of element count E32.

The upper multiplexer (14A) passes the “which image" code, and the lower multiplexer (14E) passes the "which line of that image" code.

  • Moving Objects Image PROM (11D)

This EPROM accepts as an address the image and line codes of moving objects 1 and 2 (see "Moving Object Multiplexing" above). It then presents the appro~ priate data for one line of the image to the output shift registers.

The timing of the logic insures that the correct pair of shift registers are loaded with the data, then shifted out at the correct time to become, one line at a time, the 16 lines of video for that character (Moving Object 1 or 2).

  • Moving Object Video Output Shift Registers (12D, 13D, 14D, 15D)

Shift registers 12D and 13D together form a 16 bit shift register whose task is to accept, as data, 16 bits (2 bytes) representing a Single line of the image for Moving Object 1, then shift these 16 Parallel bits out serially to become video. This operation is repeated for 16 consecutive lines, resulting in a video image that is 16 bits wide by 16 lines high on the monitor screen. Shift registers 14D and 15D together form this same type of circuit, identical in function, for Moving Object 2.

  • Moving Objects Shift Register Load Logic (2F, 16H)

This circuit sends properly timed load signals to the Moving Object Video Shift Registers. These load signals are needed to load the image data into the shift registers at locations 12D, 13D, 14D, and 15D.

  • Moving Object Shift Register Control Logic (15H, 14H)

The input signals to the upper two gates (15H) represent horizontal and vertical position “windows" for the two moving Objects (for example, MIHW = Moving Object 1 Horizontal Window, M2VW = Moving Object 2 Vertical Window). These windows allow the Moving Object shift registers to shift only at the right time. This insures the image is generated at the correct position on the screen.

The lower 2 gates of 15H are, in HARD HATIM, used for later decoding in the color selection circuitry, located on the audio and color plane interface PCB's

  • Memory Device Personality Configuration (1@D)

This is another Dip Shunt which reconfigures the PC board in order to use an EPROM (11D) of another type or manufacturer.

Page 28

PAGE 8, GAME LOGIC PCB

  • Interrupt Status Latch (8E)

This latch is set when a coin is dropped or vertical sync occurs. When the latch is set, the CPU is interrupted; that is, signal IRQ goes low. This forces the CPU to jump to the interrupt service routine. The interrupt service routine instructs the CPU to check for a coin input, and then run a debounce routine on the coin bits of ports 9E or 15A, depending on which coin input bit was set at 8E.

If the CPU finds no coin input bit set at latch 8E, it will assume the Interrupt condition was caused by vertical sync. This tells the CPU that it should now jump to the routine that services the normal game play, and that the screen can now be updated with new data. The screen can only be updated during the vertical retrace interval.

  • Option Switch Port (15A)

This port provides input from the option dipswitch, at location 16A. Data from the dipswitch is gated onto the data buss and read by the CPU at game start. This allows such options as number of turns, coins per game, additional game versus extra turn, etc.

Note that one input of this port (labeled COIN 2) does not come from the switch. Instead, it comes from Coin Input 2, and is used for debouncing the auxiliary coin input switch.
  • Control Inputs Port (9E)

This port can provide up to 8 control imputs. For only the coin1 input is used. Data from this port is gated on to the data buss for examination by the CPU during the regular service routine (which is synchronized to the vertical interval). The COIN] input to this port is used for debouncing the standard coin input.

  • Moving Image Latch

Only the CPU can write to the moving image latch. This latch contains the code that specifies which image or images are presently being displayed by the hardware moving object circuitry.

  • Audio Board Port

This latch is written to and read by the CPU, and transmits instructions to the audio board when any sounds are enabled, disabled, or the game is initialized. In addition, this port passes data sent to select colors for screen images. For the functions of these instructions, see the audio board schematic and/or description of operation.

  • Control Port Latch (9D)

This latch, used only in table versions, is written to only by the CPU and keeps track of which player is "up", in order to select which controls are active, that is, player one or player two.

  • I/O Decoding (7E)

The upper half of this decoder generates the chip selects for those I/O devices written to by the CPU, and the lower half generates the chip selects for those I/O devices which are read by the CPU. See the detailed memory map for more precise information.

Page 29

Meving apsecT 4 HORE. COUNTER ‘MovINe ORTECT 2 WoRz, COUNTERS

» & &

& Es = Ea

sum mene cues ap Rea e ces apie 3 mex appl ee eo max HH? lel he Le mons) “HE? he cur Ac © cin _a ec oMf cuR_A 8 c ! aia i mbit gem chown if BET a pes 2 mew

  • Ley Ds tse = Ly

mone oBsecT 4 towns oerecr 2 VERTICAL CowsTeRs| VERNAL COUNTERS

os Es & & =

o T

Ea

nes ra suo | ema ees ma

Sion | www mew -23ces____} De enc a] Ec — 4] Tees] essa —bepR___z}

7 Cs]

SE )é oe tne

oe inn aeeent WRITE MOVING OBTECT’ DECODING J4

8 vioeo ‘ann ourrur ie ro. PLANE INTERFACE. PCB

G502 GAME LOGIC PCB

TERT ATE OOTP OBJECT POSITION COUNTER: [70008 ot

Page 30

PROGRAM MEMORY Sec srr AnUAL For Wrovtias Fs,

els 2a a3 2201 as re Dee as aa m2

ry cinROS raspe Fee = ee 4 ss i (a4
eeAOS rafis r08— a ray “Tso a 7 is wos
ry amoa iei CI os A Cc ke z i (ce
s ake1: iso[a— a0 ra ay Sif es is FT oar

ms 702 os [nwo ra af fa ee ms hn woe

ro %co 2 ele ‘3800 xz]5805 ne3 Keo
x 7i 7Ey ay* 7
2co elee0
wah»uA108=
wes) edenes? 18dennessDATE BUSS
2wee armenaparen _a
20ww 2]‘ar 20 0]
rc)a}re]

L__J a7gg 3

s}2 207 as espa OT Fsno?oe
ro2 he a0 mes hie pe neoobe
aoes res ro Sots aos ore405oefis Ros,
ieoh woe =Oia no a2aoebo CT
Fa[a 00 ne i 3 R0oa03 Re
=ne lhoBeens sr
*”thmS

pose a dena reas enn pare at paren aris] fara]

PRON ADDRESS Configuration Shown +5 PORSONALIT? For *BV ond 2732 EFROMS, on

See TECICAL MANUAL ForCosfigurition chown a3.EXIDY INC.
cohiynhae lar otherconfiguration shown +=—
pewery devices.Gor #3 onty 27.32 | EPREAS,oe FOEFAcas

Ste TeCmMcAL manu for Fibs GARE IOOIC PEE emgage other A edt

memory 5soreBort
Page 31

[movie oe seer! mine PLEXING move OBTECTS HAASE STORAGE Movie oesrer 4 vioca gurrer Sales REsISTER manne parecer 2|

rede |

mre

az sf EZi|mvos‘4won |
me ol TsLF] aig fo?FE sagey|S mMEcrae
nee appanes ismvD
ce A1zimos9
nna]1=ismoe=
mine]3] ND fiovoz3
mei — 2]@°mrz
eaeleeal Peoesscux than138:
eeezi]zc

20 deur = et

ineee2
mes sf FERRI 2iie unis!
mae\oij
musThe'1meoa ve
inne:erei
xIe:eesee
me —s]**'+ose}
en eresLmse
pveSELvoz 3

weet mor 2] nemon? Device

POR =OWALITYcaaise

Sesne—e) ot" ze" ure 3, Sour

aarea ftGara fot
mount OBSEeTS:745

Shi REGISTERS fa [one tose | -tOSte

Da te v3] $869, [ez sesne

se6 9exesiwee
teenew e800| 144 [seaBootpura
ee 8Sie ceical lez,
Pies|,sewn elo | pceTT

= Loy Caer : 100) #{ pt Sf pe_I a

a enema 10

(Ewe gececro oe]weve 10>,swoevor

‘arick Movies Object?) ven

mon? OBse=TS SwET REGISTER TOE GAME LOGIE PCE earrase 1361 = _— =

MOVING O8JECT VIDEO GENE RATION

Page 32

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 33

MEMORY EXPANSION AND I/O BOARD

The FAXT™M Memory Expansion and I/O Board serves two purposes.

The first is to allow the CPU access to large amounts of data required because of

the large number of questions that FAX™ contains (350 - 4900). The board can

hold up to 24 8K byte chip‘s. The total capacity of the board is therefore 192KB. The CPU can access only one Eprom at a time. The contents of the latch at 11C determines which Eprom resides in the CPU*s memory map at any given point intime.

The second function is to provide a mechanism to allow the CPU access to control panel information consisting of "A" through "D" buttons for both player 1 and Player 2 as well as player 1 start and player 2 start.

This is accomplished via buffers at 4D and 7D plus associated support circuitry.

Page 34

ee ee eee MemoRY Er7AN> 0% ae sup 10 "Bose

Page 35

is wow SILER MEHO%: EXDANSION AND TO BouRd

Page 36

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 37

AUDIO/COLOR PCB-GENERAL DESCRIPTION

The Audio/Color PCB is so named because it contains not only the circuitry required to generate all sounds, but also the main color selection decoding circuitry and video output connector.

This PCB contains a dedicated 6502 microprocessor and circuitry to support the simultaneous generation of many types of sound, including three channel music. The Logic PCB simply sends commands to the Audio/Color PCB via a bidirectional communications port and the Audio/Color PCB takes it from there. In some cases this PCB even aids the Logic PCB in some of it's calculations when there is not enough processing time available on the Logic PCB.

As a result of this structure, the actual program to generate sounds or music resides on the Audio/Color PCB. There is also a handshake required between the two PCB's in order for the system to power up correctly, and of course, there is no video output without the Audio/Color PCB connected.

Page 38

PAGE 1 OF 5, AUDIO/COLOR PCB

1. Logic and Power Interface (P5,J2,J3)

Connector P5 provides the audio/color PCB with all the power it requires to operate. Also fed through this connector are the two speaker output leads. P5 interfaces only to the power supply module and the speaker, through the main harness.

Connectors J2 and J3 are the most significant path of communication between the Logic and Audio/Color PCB's. Address lines, Bi-directional Data lines, processor control lines, and the Audio/Color PCB Select line are all passed through these two connectors.

  • Commanications and Address Decoding (9B, 13D)

Peripheral Interface Adapter (PIA) 9B, in concert with 8B (another PIA ,shown on page two) serves as a bi-directional communications path between the Logic PCB and the Audio/Color PCB. During information transfer between the two PCB's, both PIA's are in use. Information from the Logic PCB microprocessor passes through the PIA at 9B to the PIA at 8B, then to the microprocessor on the Audio/Color PCB. When information is passed the other direction, the path is the same, but the direction is reversed.

During the time that no information transfer is occurring between the two PCB's, both microprocessors can continue to operate independently.

Also shown on page one is 13D, a 3-line to 8-line decoder, used to generate the write signals for the Color Data Latches. These Latches will be covered in the text for page five of the Audio/Color PCB.

Page 39

PAGE 2 OF 5: AUDIO/COLOR PCB

  • 6582 Microprocessor (3B)

This microprocessor is the same as that used on the Logic PCB, but is exclusively dedicated to the generation of sound. It can communicate with the Logic PCB microprocessor, and receives it's instructions thereby. Once it has received it's instructions, however, it asserts complete control over all Audio/Color PCB circuitry and ignores the Logic PCB microprocessor until such time as it is informed that another command is ready. Some commands are of a type that must be processed immediately, irregardless of other operations in progress, and some commands can wait until the operations in progress are completed. The program on the Audio/- Color PCB handles all these eventualities appropriately.

  • Peripheral Interface Adapters (8B, 7B)

The PIA at 8B, as mentioned in the text floor page one, is used in bi-directional communications between the microprocessors on the Logic PCB and the Audio/Color PCB.

The PIA at 7B is used for two fundamental purposes on this PCB. The first, and mst

important, is that it contains the RAM that the microprocessor uses for zero Page and stack operations. The PIA only contains 128 bytes of RAM, which under normal circumstances would not be sufficient for both zero page and stack. In this case, however, the memory map on this PCB has been altered, so that when the microprocessor thinks it is putting the stack at address Q1FFH it is actually putting it at address Q07FH.

The second use of this device is that of a programmable interval timer, used for various purposes unique to the specific sounds being generated on this game. The ability of this device to generate interrupts at time out is utilized here.

  • Address Decoding (4B)

Keyboard Encoder (4B) is used here to generate the chip selects of all devices located in the memory map of the Audio/Color PCB.

  • Music Generator (2B)

Another Programmable Counter/Timer device is used here to generate msic (and sometimes other special effects) in up to three channels (or voices) simultaneously. The music is created by a special software operating system, and all but the counter/timer chip is therefore invisible.

  • Master Oscillator (Al,B1)

This oscillator is the source of all timing on the Audio/Color PCB. If this clock stops running, so does everything else on the Audio/Color PCB. It is, how ever, completely independent of the clock and other timing signals generated by the Master Oscillator located on the Logic PCB.

  • Program Memory (5A, 6A, 7A)

The memory devices used here are 2716 (2848 x 8) EPROMS. The DIP shunt located at 8A is used to reconfigure the control and power supply lines, if necessary, for equivalent devices from different manufacturers, whose pinouts may not be the same.

7. Output Filter Latch (1C)

This latch is used simply to switch different output filter capacitors inor out of the circuit to soften or shade the sound, according to program requirements, or to change the volume.

Page 40

PAGE 3 OF 5: AUDIO/COLOR PCB

  • Clock Manipulation and Noise Generation Circuit (3D,4D,6D,5E)

The timers inside Programmable Timer Module 3D can be incremented or decremented either internally by the Phase Two clock input, or externally from the "C" inputs (C1,C2,C3). Both options are used by the program. When the counters are being controlled by the Phase Two clock, the "C" inputs have no effect, and the noise generation circuit is therefore inoperative. In order to generate sounds that are classified as noise, or contain some kind of noise within them, the counters are programmed to decrement in accordance with the input on the "C" inputs. While in this mode, the combination of 6D (Dual "D" Flip- Flop) and 5E (128 Bit Shift Register), are used to "randomize" the clock inputs to the Programmable Timer Module (3D). The “randomizer" can be clocked with either the Phase Two clock or counter output Ql.

  • Amplitude Modulation Control (2D, 7, 8, 90),

Counter (3D) outputs Q1,Q2, and Q3 are already highly complex sounds, but in order to create much more specialized audio they must be modulated in amplitude. Each channel is separately controllable in amplitude by associated Digital-to-Analog converters comprised of analog multiplexers and a resistive ladder network. Three control bits on each multiplexer select a voltage to output, according to which input pin is addressed (since each input pin is tied to a different point, and therefore voltage, in the resistive ladder). The voltage thus selected is applied to one of the two inputs to each segment of 2D (another triple analog switch). The other input is tied to ground. Note that the control bit to each analog switch segnent is one of the previously mentioned count outputs (Q1,Q2,Q3). In

thismanner,eachoutputcanbe

controlled for frequency and amplitude individually.

Note also that the count output from Ql, unlike Q2 and Q3, first passes through yet another analog switch whose function is to turn off the count output of Ql prior to reaching the Digital-to-Analog conversion stage. This is done because the Ql output is the one used for selective clock frequency generation, and would therefore interfere with other sounds if not disabled at the appropriate time.
  • Output Summation and Special Effects Volume Control (2E)

The three segments of Operational Amplifier 2E are configured as voltage

followers(forimpedanceconsider-

ations), and their outputs are summed together at the top of a 10K POT, R3l.

Theoutputvolume,thereforeis

determined by the voltage applied at each input and the adjustment of the POT.

Note that the resistors used to sum these three outputs together are large in value, so that each channel will have minimal effect on the others when
conflictingsignalsarrivesiml-

taneously (except, of course, that their sum will appear at the output).

This summed output is then again summed with all other sounds generated by this PCB at the input to the final Power Amplifier.

Page 41

PAGE 4 OF 5: AUDIO/COLOR PCB

  • Summing Amplifier and Master Volume Control (3F, R46)

One segment of Operational Amplifier 3F is used here as a point at which all the various sounds generated on this PCB are brought together. Note that the output goes immediately to a 10K POT (R46) which has ground on the other end. The wiper, therefore, varies the final output volume of all sounds together.

  • Integrator and Audio Power Amplifier (38, 10F)

Another seqment of Operational Amplifier 3F is used here as an integrator; that is, it is used to “roll off" the higher frequency sounds in order to prevent the power amplifier from going into unwanted oscillation. The Audio Power Amplifier (1@F) is a Dual Audio Amplifier IC configured as a “Bridge Amplifier" and may be either a 14377. or =LM378 for Revision A, Audio/Color PCB. Revision letters are located at position 11C. Information regarding this is available in the operators manual for this game, or contact the Exidy Customer Service Department for assistance if you must use an alternate device.

Volume Controls

Master Volume R46, see the fourth page of Audio/Color PCB schematics.

Music Volume R93, see the fourth page of Audio/Color PCB schematics.

Special Effects Volume R3, see the fourth page of Audio/Color PCB schematics.

Page 42

PAGE 5 OF 5: AUDIO/COLOR PCB

  • Pattern Character Color Division (19A, 9A)

The two segments of Flip-Flop 10A, using the upper two address lines from the character generator circuit, divide the character generator RAM space into four (4) conceptual groups (or quadrants) according to address. This is done in order to assign different colors to different characters.

Using this method, any character stored in a particular quadrant will be the same color as any other character stored in that same quadrant. If the same character is stored in a different quadrant, it will be displayed with a different color. The output of 9A (Twoline to Four-line decoder) applies the separated video lines of these quadrants to priority encoder 10B, whose task is to determine which image is to take visual preference when two or more coincide on the TV screen; that is, which image is to appear to be in the "foreground", and which is to appear to be in the "background".

  • Priority Encoder (1@B)

All the video signals generated by the logic PCB are applied to the priority encoder. The signals assigned the higher priority are shown at the top, and the lower priority are shown on the bottom. The output of this device is a3 Bit code representing the highest priority video line active at that instant. This output code is then sent to the color multiplexers as an address which will select the appropriate color for the imagery generated on that video line. Note that the lowest priority input to the encoder is tied permanently low (active). This insures that when no other video is being generated, there is a background color present, unless of course, the program has selected a jackground color of black at that time.

  • Color Data Latches (11C,12C,13C)

These latches are addressed directly by the Logic PCB microprocessor. Here the microprocessor stores the data that determines which character is what color. This data is then passed to the color selection multiplexers.

  • Color Selection Multiplexers (11B, 128, 13B)

Each of the three multiplexers controls the video output toa different color gun in the CRT. One turns the red gun on or off, one turns the green gun on or off, and the third does the same for the blue gun. The output combination of the three multiplexers provides for oe of eight possible colors to be displayed at any given instant. The color displayed is determined by two things: what type of video is present (e.g. which character), and what color the microprocessor has currently assigned to that type of video. As mentioned above, the color assignations are stored in the color data latches. The priority encoder (18B) issues the code representing the type of video currently displayed. Using these two pieces of information, the multiplexers look at the appropriate bits in the color latches and send the data directly to the TV to turn the color guns on or off.

5. Video and ae Signal arity

Selection (TTA, 12a)

Before being reclocked one last time, all video outputs are passed through an Exclusive-Or gate (11A), so that one input of each segment can be used to invert the video (make it 188 degrees out of phase with respect to the input to the gate). This feature insures compatibility with TV monitors made by several different manufacturers.

The TV Sync signals are also routed through Exclusive-Or gate segments (12A) for the same purpose.

  • Final Video Output Re-synchroniza~ tion (13A)

To insure that all video signals and sync signals are accurately synchronized in time, they are all re~clocked one last time together by a HEX "D"Flip-Flop. It "cleans up" any spurious irregularities or propagation delays that may have crept into any of the video or syne signals.

Page 43

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 44

fe pao) =a mt [rom me sa m nos fa an ms roe mm | = was

Silt bos cai] EY be of » rea ra we] sl fe Bs =a bear ome oy re bea ~ w Be mt ro as oa Re

nore 40 Ans acaiio mob be dite Erveigers sown 2B ae ) ga53 on

*

77-0007-0!

Page 45

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 46

D

c

P HUNT CONFIGURATION

Fe a wore 1: . ws? 378 MO ge po ren (ort)

HAT SINK

B

we RG tne ben ser) a Thee |__ Fea

A

NEAL R. ZOOK “TA, vow STRUER AUDIO/COLOR PCB "4 caceal a ee —— oe SCHEMATIC. DIAGRAM l- 5 77-0007-01

3 7 6 5 2 4 ] 3 | 2 l 1

Page 47

wa FY

8765x4321
se DATA LaTENcoe seecTion+”
ABD.19Lah 5 RED
z20ABEpe gesl, Ype
14 FI DIP SOCKET ConECTOR‘ABD2hs aiti ybevives Poaety 9 8
_ABO313]i45] ¥en
SéL0>“3fsPaesD
Be:Ks
SieaoeSp 378 oe2 16cor Foe
sevieABD E4Bir istLowereue
vieAEDy3Eirn
FROMMHSYNEWRED4.5
Looe resENDyp
74sVNCbe
eae$rain

SHOWvIO F

j_vivyls owmn) ‘> s GRNA=

SV. EL

}|_YD7AIO_++Gi)
+5 VDC.LPr?Syne BLA

«)) 82 $s | my

Hbe1

sic mamy $230

waePar)Esc

smn coy. aa

  • 2 ow _sesme _J~1)) g>2-—1 PATTERN) CIARKCIER CoLok DIVISION an pa 6 HsycA nsmme__17})) ,>*—tee — BB i aA
iioerveruc__—1)) gs —Yetice

wav

PRIORITY ENCODER snes mre

10 PI wareR WEA

—ReoAsep ootot
biGRWA‘GN our4
pis,BLvAa] .g [7 eww oor.3

cewek] 8 fees or 3) eurrer ro Treinen 5] "4 fig—pemeoor 4] rv monroe

vec],fis ave oorS] ervey ma

é aewers )

: to i

Fdio/ vor wee SCHEMATIC DIAGRAM 77-000T-01 You fe

3]2
Page 48

APPENDIX B: ILLUSTRATED PARTS LIST FOR FAX™

The following is an illustrated parts list to aid you, should you need to order replacement parts for FAX™, the drawings have all parts labeled by a number within a circle. This number refers to the item number on the Parts List directly across from the drawing. In the case of the Final Assembly list, the second drawing has numbers referring to the Final Assembly list found opposite the first drawing.

Following the Illustrated Parts List is a list of parts for the Logic, Audio and Plane Interface boards, Memory Expansion Board and overall cabinet hardware.

Page 49

A. FAXTM FINAL ASSEMBLY

Item Part Number

98-8073-20 65-2891-88 61-2849-98 65-9092-98 51-2194-25

80-9054-90 65-8098-00 59-895 2-30 54-1190-20 98-0074-98

79-6981-28 51-3896-298 53-3908-90

89-0258-08

95-0923-88 95-9825-00 49-9928-95 65-8994-99 58-1182-88 51-2204-98

48-3902-008 48-3903-08

61-0948-08 61-0835-28

98-8975-00 51-2098-21

90-BB76-B8 51-2088-@1

95-8914-89 49-9823-85 51-2204-88

$5-G989-98 65-0888-88 50-3396-22 54-3308-01 Description

Assy, Cabinet Speaker Grill Face panel Assy Retainer Channel Screw #8A Sq.Dr.x 1/2

Fax™ Dis: lay Plex Plex Bracket O-Ring #2 5/32IDx1/16 Kep Net 46253 / TV Bezel Assy

Monitor, 13in 13K48@1 Screw, #18 HiLo Pan Hdx3/4 Washer #18

Anti-Glare Filter, 13in.

Fluoresent Bulb Fluoresent Socket Bryant Assy Lamp Ts, Bracket Lamp Holder Screw, 6-32x1/4 Screw, #8AB Pan Hd x 1/2

Switch Assy Starpoint Switch Assy Starpoint

Front Door Assy Rear Door Assy

Power Supply Assy Screw #8 FH Wood x 1.8

Isolation Transformer Assy Screw #8 FH Wood x 1.9

Coin Door Assy Assy FAX™ coin Door Harness Screw, #8AB Pan Hd x 1/2

Coin Box Door Bracket Hasp Bolt Carriage 18-24x3/4 Kep Nut 10-24

Page 50

A-FAX™ FINAL ASSEMBLY continued

Item Part Number Description

95-@016-@8 Cash Box, Plastic

65-8999-88 Bracket Coin Counter 95-@915-@8 Coin Counter 51-2204-96 Screw #8AB Pan Hd.xl/2 50-O806-09 Screw #4-40 Pan Hd.x3/4

95-8817-08 Speaker 9x6 Oval 65-0895-98 Speaker cover 51-2086-81 Screw #8 FH Wood x3/4 49-0827-85 Assy Speaker Harness 48-5001-98 Interlock Switch 65-0B96-08 Interlock Sw.Brk.x.58 65-0997-20 Interlock Sw.Brk.x.75 51-2284-88 Screw,#8AB Pan Ha x 1/2

49-8829-85 Power Cord Assy 51-2284-@8 Screw #8AB Pan Hd x 1/2

77-9807-85 PCB Audio 77-©888-85 PCB Logic 77-®@15-@5 PCB Memory Expansion 77-@@06-05 PCB Plane Interface 51-2204-08 Screw #8AB Pan Hd x 1/2

49-9024-95 Assy FAX™ Main Harness 49-8826-985 Assy FAXT™ control Harness 49-@925-95 Assy FAXTM A.C. Power Harness 51-2204-68 Screw #8AB Pan Hd X 1/2

Page 51

EEE) B. FAX POWER SUPPLY ASSEMBLY, 90-0875-08

Item Part Number

WO UD OB WN 32-8901-28 77-@201-95 36-881-00 31-9991-99 69-9358 80 51-3204-88 51-1204-88 55-9801-88 59~-1195-98 53-1904-09 54-1196-91 13-4985-89 13-3364-29 13-6844-89 21-9803-88 21-2884-28 21-8206-08 20-8993-20 20-2985-98 Description

POWER SUPPLY, 5V @ 6AMPS PCB_REGULATOR XFMR STEP DOWN EMI FILTER POWER SUPPLY MOUNTING BOARD SCREW, #10 AB PAN HD x1/2 SCREW, PAN HD, #6 X 1/2" LG. TYPE AB SPACER, #6 x .1/8 NON-METALLIC SCREW, PAN HD. #6-32 x 5/8" LG. WASHER, FLAT, #6 NUT, KEP, #6-32 CAP ELECT 4800 MF 50V CAP ELECT 33 MF 25v CAP ELECT 6.8 MF 25V TRANSISTOR 2N3055 TRANSISTOR 2N6246 REGULATOR 7912 DIODE 698$1/UT 4918 RECTIFIER, BRIDGE MDA-979-1

\ ley

[ifije \ ab :

—]

[——T i =r [| ®

Page 52

C. ISOLATION TRANSFORMER ASSEMBLY, 90-0076-00

Item Part Number Description 30-0202-00 TRANSFORMER, ISOLATION 30-0204-08 § FLUORESENT LAMP BALLAST 95-0026-08 FLUORESENT STARTER SOCKET 95-0024-20 FLUORESENT STARTER (F&S) 6@-@351-08 | MOUNTING BOARD 51-3886-28 SCREW, #10 HiLo PAN HD x3/4 53-3000-00 WASHER #10 FLAT 51-@185-29 SCREW, #4A PAN HD x 5/8 51-2204-08 SCREW, #8AB PAN HD x 1/2 WDIHEUBWNE

Page 53

D. COIN DOOR ASSEMBLY, 95-0814-00

item Part Number Description 1 95-8814-68 COIN DOOR 2 49-B023-20 COIN HARNESS ASSY

Page 54

E. LOGIC AND AUDIO BOARD ASSEMBLY 90-0005-00

OYHAUNRWNH 77-@828-85 77-8207-85 55-8202-28 50-1102-208 36-B2B6-BB 59-8956-20 36-2205-08 77-8286-25 PWA LOGIC PWA AUDIO COLOR SPACER NON-METALLIC #6-32 X 7/8 LONG SCREW, PAN HD. PHIL #6-32 x 1/4 LG : CABLE ASSY, RIBBON, 14 PIN WASHER, FLAT, NYLON #6 PLANE INTERFACE RIBBON CABLE . PLANE INTERFACE PCB ASSEMBLY

Page 55

F. PRINTED CIRCUIT ASSEMBLY-UNIVERSAL POWER SUPPLY, 77-0609-@5

ODIDARWNE 71-6009-64 13-4985-20 13-3364-08 13-6844-06 28-0203-08 28-B005-00 21-9083-20 21-0004-20 21-2005-20 21-006-2B 84-G012-00 84-2813-08 409-002-068 58-4927-28 53-4911-@1 37-6801-20 UNIVERSAL POWER SUPPLY BOARD CAP, ELECT. 400@MF, 5QV AXIAL LEAD CAP, ELECT. DIP 33MF 25V + 20% CAP, ELECT. DIP 6.8MF 25V + 20% DIODE 60S1 or UT4@10 RECTIFIER, BRIDGE MDA-970-1 TRANSISTOR, 2N3055 TRANSISTOR, 2N6246 REGULATOR 7905 REGULATOR 7912 HEATSINK HEATSINK CONNECTOR 12 PIN (WAFER HEADER) SCREW, PAN HD #4-40 x 3/8 LG (PHIL) NUT, KEP #449 TIE WRAP 5 1/2"

Page 56

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 57

G. LOGIC BOARD, continued

Item Part Number

48 18-1044-1 41 13-6844-1

42 13-3365-8

43 13-4775-8

44 47-2001-28 45 49-5882-08

46 29-2001-28 47 48-206 1-08

48 44-1601-26

49 44-2491-20

58 44-4061-26

51 44-1491-06

52 44-~1801-28 53 11-1953-28 54 @2-2212-26 55 @2-1802-06

68 18-2214-4

H. AUDIO/COLOR BOARD ASSEMBLY 77-0007-05

71-2087-64 22-@013-02 26-2093-06 25-0202-00 25-0204-20 27-2201-20 22-0022-B2 27-0082-28 22-2023-28 22-0055-28 FUOUDNDUBWNE Q Description

CAP. 6.8uf 25v DIPTANT CAP. 33uf 25V ELECTROLYTIC CAP. 47Quf 10V ELECTROLYTIC DIPSHUNT JUMPER PAKS 16 PIN DIP SWITCH 8 POS. CRYSTAL 11.289mhz (SERIES) 10 PIN MALE MOLEX HDR DIP SOCKETS 16 PIN LOW PROFILE DIP SOCKETS 24 PIN LOW PROFILE DIP SOCKETS 48 PIN LOW PROFILE DIP SOCKETS 14 PIN LOW PROFILE DIP SOCKETS 18 PIN LOW PROFLE CAP luf DIPTANT RES. 220 OHM 1/4W 5% RES. 18 OEM 1/4W 58 CAP. 330 pf CER. DISC E PROM, 2732 FXL E PROM, 2732 FXL E PROM, 2732 FXL E PROM, 2732 FXL Location

1c, 15D, 1c, 2c 6E, 13F

10H

4B, 11B, 10D

16A 1D

lec, 16F 4B, 11B, 14H, 10D | 6A thru 13a, 11D 5c, 6D

2a

16B

4A, 5A, 7B, 8B, 11C 12c, 13c, 14¢ c45 thru C52, 5D, 2H R268, R311 R308 thru R302 5D 6A 7A 8A OA CAP 220 pf CERAMIC DISC E PROM, 2732 FXL E PROM, 2732 FXL E PROM, 2732 FXL E PROM, 2732 FXL-6 E PROM, 2716 FXL

PRINTED CIRCUIT BOARD I.C. 74LS138 I.C. 6526 I.C. 6532 I.C. 6582 I.C. 6849 I.C. 74LS154 I.C. 8253 I.C. 4069 I.C. 4813B 10a 1lA 12A 13A 11D

13D

3B 3D 4B

1A 1B

Page 58

H. AUDIO/COLOR BOARD ASSEMBLY, continued

Item Part Number Description

1122-0003-62I.C. 74LS84
1222-801-02I.C. 74LS06
1322-0821-G2I.C. 74LS374
1422-0024-20I.C. 4953
1522-0025-20I.c. 4175
1622-8056-28I.C. 4562
1722-@611-02I.C. 74LS74
1822-0826-28I.C. LM324
1922-0854-08I.C. 7486
2822-@827-2I.C. 74LS86
2122-2828-00I.C. 4051
2222-6014-82I.C. 74LS139
2322-2057-00I.C. LM377
2422-@829-82I.C. 74LS148
2522-030-02I.C. 74LS151
2622-@831-82I.C. 74LS174

27 10-1644-1

28 10-2264-1 29 18-1034-1 3o 13-3365-1 22pf CERAMIC CAP 16V

33uf CAP, 25V, ELECTROLYTIC W/AXIAL LEADS 1@@uf CAP ELECTRO- LYTIC 16V 4.7uf CAP ELECTRO- LYTIC 16V 1.Quf CAP ELECTRO- LYTIC 16V 1.8K RES. 1/4W 5% 3.3K RES. 1/4W 5% 1K RES. 1/4W 5% 1M RES. 1/4W 5% 300 OHM RES. 1/4W 5% 100K RES. 1/4W 5% 31 13-1875-@8

32 13-4755-08

33 13-1955-28

34 ®2-1822-08 35 @2-3322-28 36 ®2-1822-08 37 ®2-10862-08 38 %2-3812-08 39 $2-1842-08

46 @2-2232-28 4l ®2-1952-28 42 92-3332-08 43 ®2-2722-00 44 @2-2732-28 45 ®2-1322-08 46 92-6812-88 47 ®2-3312-08 48 @2-1612-88 22K RES. 1/4W 5% 1M RES. 1/4w 5% 33K RES. 1/4W 5% 2.7K RES. 1/4W 5% 27K RES. 1/4W 5% 1.3K RES. 1/4w 5% 680 OHM RES. 1/4w 5% 330 OHM RES. 1/4wW 5% 168 OHM RES. 1/4W 5% Location

5D 6B 1c, llc, 12C, 13Cc 2D, 4D 6E, 73, 8E, 9E 5E 1@A, 6D 3F, 2E 1D 11A, 12A, 4E 7D, 8D, 9D 9A 18E 10B 11B, 12B, 13B 13A -luf. CERAMIC CAP 25V 1A thru 7A, 9A, 11A, 13A, 1B, 6B, 9B, 11B, 1C, 11C, 13C, 1D 3D, 5D, 7D, 9D, 11D, 13D, 1E, 2E, C7, C9, C10, 3E, 5E, 7E, 9E, C12, 13E, 2F, 4F, 12F, 98, 2E, 3F cl -@1 uf CERAMIC CAP 16V C6, C8, Cll, C33, IC C13, C15, C17 thru C21

clé

C3, C4, C5

C27, C32, C2

R3, R4, RS R6 R14 R2 RL RIO, R11, R12, R27 R47, 428, R29 R15, R3O R32 R33, R35 R34 R21 R44 R26 R19 R7, RB, R24 R25

Page 59

H. AUDIO/COLOR BOARD ASSEMBLY, continued

Item Part Number

oi) @2-8282-00 B2-3902-00 97-1032-20 97-0004-20 B9-B2B8-28

29-0202-00 47-G061-20 44-1491-08 44-2491 -28 44-2801-26 44-4981-20 44-1681-08 13-4735-20

4B-005-18 37-0089-20

75-B006-20

41-2203-29 Description

82 OHM RES. 1/4W 5% 39 OHM RES. 1/4W 5% 10K RES. 1/4W 5% 10K Por 4.7K RES. PAC 16 PIN SIP 3.579545 MHZ CRYSTAL 16 PIN DIP SHUNT 14 PIN DIP SOCKET 24 PIN DIP SOCKET 28 PIN DIP SOCKET 49 PIN DIP SOCKET 16 PIN DIP SOCKET -47 uf CAP ELECTRO- LYTIC 16V 1@ PIN MALE CONNECTOR 1@ PIN FLAT CABLE ASSEMBLY HEATSINK STAVER V7-1 E PROM 2716, FXA-2 E PROM 2716, FXA-2 E PROM 2716, FXA-2 FEMALE 10 PIN

I. PLANE INTERFACE BOARD 77-0006-05

Part Number

771-2066-B4 10-1944-1 22-0001-02 22-0617-22 22-2620-02 23-0845-28 44-1481-08 44-2481-20 Description

PLANE INTERFACE BOARD «UF CAP., 25 VOLT I.C. 74LS00 I.C., 74LS166 I.-C. 74LS245 I.C., 6116 14 PIN SOCKET 24 PIN SOCKET Location

R2O R22, R23 R16, R17, R18, R42, R45 R9, R31, R46 4D

2A 8A, 11E J28, 1A, 1B, 5E 3A, 4A, 5A, 6A, 7A, 2B 3D 3B, 7B, 8B, 9B 2D, 4D, 8A, 11E, 6E- 9E, 7D-9D c14

P21 J2, J3

ONLY W/ 14277, LM278 5A 6A aN

Page 60

J. MEMORY & I/O EXPANSION BOARD 77-0015-25 Part Number Description 77-@015-04 PCB board 22-2001-82 I.C. 741508 22-20108-22 I.C. 741832 22-@813-@2 I.C. 7418138 22-@814-2 I.C. 7418139 22-@828-2 I.C. 7418245 22-0831-02 I.C. 7418174 22-037-02 I.C. 7418125 22-0861-62 I.C. 7418244 29-BBS3-BO 22 Ohm Res.Pac 29-QOB4-BB 2.2 k Sip Pac 18-1044-18 sluf cap 13-4787-08 47®uf cap ele.l6év 4G-2005-18 18 pin molex .156 48-0821-18 10 pin inline .108 4B-OG21-12 12 pin inline .188 41-0005-28 48 pin connector 44-1681-20 16 pin socket 44-2801-20 28 pin socket 23-0076-20 Data E-PROM set FXD-xx Consist of up to 24-2764 EPROMs depending on data version (xx). Location possible are 1C thru &, 1B thru 8B, 1A thru 8A. 24-0014-28 Prom FXD-1 12B 49-2038-05 Ribbon Cable

Page 61

SV SUPPLY

STEP DOWN.

  • EMR REGULATOR BOARD

FILTER

M™VIRING DIAGRAM POWER SUPPLY _ASSY.

NOTES UNLESS OTHERWISE SPECIFIED

Page 62

12345675900 e134 5] loRN/ BLK ViO7 BLK RED ED

FAX_ MAIN HARNESS RED. T2 345675 D101 213145 617 BD DAWABCDOEFAT KLMNER STUVWKY 2| fi Z| fd 213456]

49-0024-00

Page 63

vac

vac i ual 33 [amauns — -—12v (Lo)

—12V (HI) } GND

Tr]eSCRETONToate | apenoven5
HTREVISED PER ECN 00235730-61 =Zu

bg a a ges Soa cR2 Qi za $ TL REF. w3 35 sa 2N3O55 209 Jt 24 VCT. 4aMP a

>iiunfsevin$33

t :

tesKez<J-
criJer vatt 33

© + 5 ees ree INT yai2 [OUT 10 | +i2vwo0

i SPARES

Notes UNLESS OTHERWISE SPECIFTO

c UT

co TOLERANCES UNLESS OTHERSE SeRCIEED BREN PUCES INCH Oa FEA xx [Fe WExT ASSY use ON | xxx [Fy TT3B6S-15 | VEUTURE | —as fe

Page 64

St S2 MECH | MECH 2

NOTES UNLESS OTHERWISE SPECIFIED COIN COUNTER

m™ FAX COIN DOOR HARNESS BB) A | 2:0028-00

Page 65

FRONT INTERLOCK

HU \GOLATION TRANSFORMER: @

NN MONITOR ce fy x ES] o

GRN RN WHT. YET

GY/ BLUE 4 GY 7GRN 5 1S | IGY/RED

i} [Exes anno

x

mo AVA OF SUMIYVALE ca seams creo mt FAK AC POWSR WITH MONITOR AC. HARNESS:

NOTES UNLESS OTHERWISE SPECIFIED

Page 66

7a aueveLK | Zpaveroaw BLUE 7RED BLUE JOR

BLUE /YEL,

PLAYER 2 a

PLAYER 2

[ "A PETRETTIO ark VON STRIVER : i eon =" CONTROL,

= Et PANEL FARNESS

3 T 7 é T 3 * 4 | 3 ] 2 I 1

Page 67

id LL

POWER F| ! SUPPLY emenney, AUDIO Losi pce ae

ISOLATION XPORHER

aT, Blo oIAGRAM

Page 68

PROTECTION

| PARTS UST.

0251 cOLLECTOR

pocounen soreSe Tee Be

‘WiDw 200 SECIOW

NEGATIVE SDE OF C309

‘WinW 200 SECO ; SERVICE TECHNICIAN WaaN | X-RAY RADIATION PRECAUTION:

THIS PRODUCT CONTAINS CRITICAL

ESSENTIAL FOR X-RAY RADIATION

FOR REPLACEMENT PURPOSES, USE ONLY TYPE “PARTS SHOWN IN THE | MODELS 13K4801, 13K 4806, 13K4851, 13K4856

CAUTION: FOR CONTINUED SAFETY, REPLACE SAFETY CRITICAL COM: | PONENTS ONLY WITH MANUFAC TURER'S RECOMMENDED PARTS, ELECTRICAL AND MECHANICAL PARTS ; | AVERTISSEMENT: POUR MAINTENIR [| LEDEGRE DE SecuRITE DE L’APPAREIL ‘i ' NE REMPLACER LES COMPOSANTS 4 DONT LE FONCTIONNEMENT. EST

CRITIQUE POUR LA SECURITE QUE FAR

DES PIECES RECOMMANDEES PAR LE i, FABRICANT. 3 2 poor hi OSCILLOSCOPE WAVEFORM PATTERN i ‘The wavetorms shown are as observed on the wide band oscllioseope with the monitor turned to a reasonably 3 Strong signal and a normal picture, The voltages shown fon each waveform ate the approximate peak aml tudes. If the waveforms are observed on the oscilloscope with frequency response, the corner of the pulses will tend to be more rounded than those shown land the amplitude of any high frequency puise witl tend to be less.

K4BOIE, K4BSIE, - 5832 K48060, 48568

Page 69

Ee 390 JAVA DR. SUNNYVALE, CA 94086 408-734-9410 TELEX 357-499