CATHODE RAY TOMES

Zoo Keeper

Zoo Keeper (set 1) (Taito America Corporation, 1982) · Manual · 64 pages · 27 sections · original scan

Page 1

CN LOR SRS SS at ~-@ Nee as we

Ware ©1982 Trade Marks of Taito America Corporation 72-00036-001

Page 2

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 3
Scan of page 3

This page is a drawing, shown as the original scan.

Page 4

Reproduction of this publication is forbidden without the written permission of TAITO

AMERICA CORPORATION, Elk Grove Village, Illinois. This manual is only conditionally

issued, and neither receipt nor possession thereof confers or transfers any right in, or

license to use, the subject matter of the manual or any technical information contained

thereof.

For permission requests, write: TAITO AMERICA CORPORATION 1256 Estes Avenue Elk Grove Village, Iilinois 69007 Telephone (312) 981-1000 Telex 25-3290

Page 5

1.

2.

3. “ZOOKEEPER”™ UPRIGHT

TABLE OF CONTENTS

“ZOOKEEPER’™ GAME SET-UP ................ Page 5 4. ILLUSTRATION & PART LISTS..................... 25

1.1 Game Features ......0. 0.0... cece eee eee ee 6 Figure 1 Incandescant Panel ................04 26 1.2 Introduction ........... 00... cee cece 6 Figure 2 8-Way Joystick .............0.--.008 27 1.3. Game Inspection ................0 02. e eee eee 6 Figure 3 Control Panel ...............0..00005 28

1.4 Pre-Game Installation .......................4 6 Figure 4 Door Assembly ................00.048 29

1.5 Power On/Off Switch, Interlock Switch, Figure 5 Coin Door............-2..0 eee eee eee 30 Memory Protect Switch, Self Test Switch, Volume Control, and Service Outlet............. 7 Figure 6 Cabinet Assembly Front View .......... 32

1.6 Electronic Acceptors ................-...00005 7 Figure 7 Cabinet Assembly Rear View........... 34

1.7 Game Installation ............. 0.0... eee 7 Figure 8 Power Supply Component Layout ...... . 36 1.8 Self Test Procedure.............0..0..00. 00 8 Figure 9 Video Processor Component Layout ..... 39

Figure 10 Data/Sound Processor MAINTENANCE ................0... 000 eee eee eee 15 Component Layout

2.1 Cleaning ......... 0... c eee eeee eee 16 Figure 11 ROM/I/O P.C. Assembly Component Layout ................4 48 2.2 Coin DOO ...... 6... cece ccc e eee eens 16 Figure 12 Video Rom Expansion Board........... 52 2.3 Fuse Replacement ..............-.--00 see eee 16 Figure 13 Coin Processor Board Layout .......... 54 2.4 Monitor Removal...............00..eeee eee 16 : Figure 14 Coin Processor Board Schematic ....... 55 2.5 Cover Glass Removal .........-.-...0.ee eee 17 Figure 15 Wiring Diagram ...............00..08 56 2.6 Printed Circuit Board Replacement ............. 17 Figure 16 Power Supply Board Schematic (Fold Out) 2.7 Power Supply ......... 2.0... cece eee eee ee 17 Figure 17 Video Processor Board Schematic 1 of 2 2.8 CMOS RAM ............. cece cece eee 19 (Fold Out) 2.9 Test Points..............0c cece sees 19 Figure 18 Video Processor Board Schematic 2 of 2 (Fold Out) THEORY OF OPERATIONS ...............--...005. at Figure 19 Data/Sound Processor Board Schematic (Fold Out) 3.1 General... 0.0... e teeta 22 ; Figure 20 ROM/I/O Board Schematic (Fold Out) 3.2 Video Board ....... 6... cece c eee eee eee 22 Figure 21 Video Rom Expansion Board Schematic 3.3. Data Sound Board ............2.....0. 00020 23 (Fold Out) 3.4 ROM I/O Board ............ 62. cece eee eens 24

3.5 Video ROM Board .............--...0 eee 24

Page 6

LIST OF ILLUSTRATIONS

Figure 1-1 Programming Plug................... 6

Figure 1-2 Power ON/OFF Switch ................ 7

Figure 1-3 Interlock Switch & Memory Protect Switch7

Figure 1-4 — Self Test Switches ................... 7 Figure 1-5 — Volume Control Setting ............... 7

Figure 1-6 Self Test Button .

Figure 1-7 Video Board (On Service Door) ......... 9

Figure 1-8 Flow Chart ......................2. 10

Figure 1-9 Color Bar ....... 0. 10

Figure 1-10 Color Bar ..... 2.0... 10

Figure 1-11 Color Bar «0.0... eee eee e eee eee W Figure 2-1 Coin Door ................000 002 16 Figure 2-2 Fuse Replacement .................. 16

Figure 2-3 Monitor Removal ................... 16

Figure 2-4 Cover Glass Removal ................ 17

Figure 2-5 Printed Circuit Boards ............... 17

Figure 2-6 Power Supply ...............022200. 17

Figure 2-7 Current Limit Adjustment ............. 18

Figure 3-1 Clock Timing..................00008 22

Figure 3-2 Dual Port RAM Timing ............... 23 LIST OF TABLES

Table 1-1

Table 1-2

Table 1-3

Table 1-4

Table 1-5

Table 1-6

Table 1-7

Table 1-8

Table 1-9

Table 2-1

Table 2-2

Table 2-3

Table 2-4

Table 3-1

Table 3-2

Table 3-3 Table 3-4 Self Test Switches .............-..0005 7

Hardware Tests ............0.0-ee eee 8 Video Board ROM Checksum ........... 8

Video Board RAM Checksum ........... 9

Data/Sound Board ROM Checksum....... 9

Screen RAM Content ..

Audit Totals ...............--000 eee 12 Standard Coin Setting ................ 13

Custom Coin Setting ................8 13

Line Voltage .................02.0005 17

Secondary Fuses .................005 18

Data/Sound Board Test Points ......... 19

Video Board Test Points .............. 19

Video Board Memory Map............. 22

Register Initialization ................. 23

Data/Sound Memory Map ............. 24

Decoding Jumper Location ............ 24

Page 7

Game Set

Page 8

“ZOOKEEPER”™ UPRIGHT

  • GAME SET-UP

1.1 GAME FEATURES TAITO AMERICA CORPORATION'S ‘‘ZOOKEEPER’’™ upright game is housed in a compact and highly serviceable cabinet with many added features. A larger security designed cash box has been incorporated into the design of this cabinet. By putting wheels on the cabinet, moving the game from one location to another is made much easier. The Control Panel has a polycarbonate overlay, so cigarette marks and mars can easily be wiped clean. This overlay can be replaced if necessary. The Marquee and Coverglass are made of fully Tempered Glass to minimize breakage. The Back Service Door housed all the P.C. Boards for the system making servicing of the game, if needed, much easier. Lighted instructions are provided to further enhance the game and attract players, by making the instructions easier to read. TAITO AMERICA CORPORATION proudly presents out improved Self-Test capability, making servicing of the game easier, which keeps your game up and running with less down time.

1.2 INTRODUCTION TAITO AMERICA CORPORATION'S ‘‘ZOOKEEPER'’™ upright game is designed for one or two players. Players find out right off that its a zoo in there. . . and the anaimals are eating their way out! Wherever Zeke the zookeeper runs along the wall, he replaces bricks which have been chomped away. But the animals are swift and some inevitably escape. Now Zeke has to dodge or jump over them to survive--while still francically trying to rebuild the bricks. Plus, he’s trying to earn bonus points by grabbing watermelons, root beers, and other goodies along the way. And all the time the fuse is burning. Next Zeke must leap from ledge to reach his girlfriend, Zelda, held hostage by a monkey who’s throwing coconuts. The ledges move in oppsite directions, and if Zeke falls, its all over. If he can swing it at this stage, Zeke can make points here, too, by collecting bonus objects as he goes. The struggle seems all worthwile when Zelda is rescued. But Zeke still has to face two more brick Zoos teeming with the meanest animals ever. Luckily, a net can be used to catch the escaped animals and return them to their cages--IF Zeke can reach it. As the adventures alternate, survival becomes more difficult. In each of the “brick” screens, a more challenging animals with a higher point value is introduced. And in each succeeding ‘‘ledge”’ screen the “‘ledge"’ screen moves faster, until they finally become invisible. With only his memory of past ledge patterns in relation to the still visible bonus objects and coconuts, Zeke must jump from one invisible ledge to save Zelda. “Escalator’’ screens, in which bonus zoo keepers can be one to help Zeke out, are interspersed between the other screens. Here Zeke must jump onto each escalator, till he can rescue Zelda up above. The higher he gets, the quicker the animals become. But victory is sweet when Zeke saves Zelda at last!

1.3 GAME INSPECTION TAITO AMERICA CORPORATION'S “‘ZOOKEEPER''™ upright game is shipped ready for operation, but a last visual check should be made to insure the game is in good condition. Please verify the following before turning the game on. Check the exterior of the game for shipping damage, chips, dents, or broken parts.

  • Open the Rear Service Door and check for any interior damage.
  • Make sure there isn’t any damage to the wiring.
  • Check Printed Circuit Boards, making sure there is no damage to the components.
  • Check fuses making sure they are firmly in their holders.
  • Check for loose foreign objects, especially metal objects which may cause electrical problems.
  • Check Plug-in Connectors making sure they are firmly in their sockets.
  • Check Self Test Switches making sure they are not damaged. The Video Monitor is properly adjusted before shipping. If there are any adjustments necessary, refer to our Video Monitor Manual (72-00035-001) This Manual contains all the Manufacturers recommendations for adjusting the Video Monitor.

1.4 PRE-GAME INSTALLATION The following precautions should be followed when installing the game.

  • Avoid rough handling of the game, the picture tube is fragile.
  • Install the game on a level surface.
  • Avoid installing the game where it may receive excessive sunlight or heat, to protect the game from rising internal temperatures.
  • Do not install in a damp or dusty location.
  • Fora short time after connecting the power to the game, the picture may be temporarily distorted. The monitor's purity is affected by the earth’s magnetic field, causing a variation of color. By turning the game on for 10 or 15 seconds and then off for 20 to 30 minutes the automatic degaussing circuit applies a degaussing field around the edges of the monitor. Doing this several times will correct the problem. Another way to correct this problem is to purchase a degaussing coil or bulk tape eraser at any Electronics store. This will help to immediately demagnetize the Video tube. Caution must be used with a degaussing coil so the magnetic field of the degaussing coil is not allowed to become too intense at any one place on the picture tube there by causing a localized color distortion. Ifyou move the game to another location after degaussing the problem may reappear. Refer to Monitor Manual 72-00035-001 for details.

1.4.1 POWER REQUIRMENTS TAITO AMERICA CORPORATION'S ‘‘ZOOKEEPER’™ game is shipped ready for operation at 120 or 240VAC, 60Hz with a power consumption of approximately 250 Watts. The following line voltages may be selected: 1O00VAC +10% 50/60Hz 120VAC +10% 50/60Hz 200VAC +10% 50/60Hz 220VAC +10% 50/60Hz 240VAC +10% 50/60Hz Avoltage Programming Block is located on the primary side of the Transformer to compensate for high/low conditions. (See Figure 1-1).

FIGURE 1-1 PROGRAMING PLUG

Page 9
CAUTION For safe operation it is recommended the cabinet be grounded. This game is equipped with a three conductor power cable. The third conductor is the ground conductor and when the cable is plugged into an appropriate receptable, the game is grounded. The offset pin on the power cable's three-prong connector is the ground connection.

1.5 POWER ON/OFF SWITCH, INTERLOCK SWITCH, MEMORY PROTECT SWITCH, SELF TEST SWITCH, VOLUME CONTROL, AND SERVICE OUTLET To minimize the hazard of electrical shock while servicing the game a Power ON/OFF Switch, and two (2) Interlock Switches are provided. Two (2) Self Test Switches, two (2) Volume Control and a Service Outlet have also been provided. (See Figures 1-2, 1-3, 1-4 & 1-5 for the location of Switches).

1.5.1 POWER ON/OFF SWITCH, INTERLOCK SWITCH A Power ON/OFF Switch is located in the front of the game at the left hand side of the cabinet. There is two Power Interlock Switches, one is located on the inside of the Coin Door frame and the other is located at the inside rear of the Service Door. This switch removes all the power from the game without unplugging it from the wall outlet. Power may be restored for servicing by pulling out on the Interlock Switch Button.

Ca id N\

FIGURE 1-2 POWER ON/OFF SWITCH

1.5.2 MEMORY PROTECT SWITCH The Memory Protect Switch is used to prevent erroneous writes to locations in the CMOS RAM which store the location program variables.

Coin Door Memory Protect Switch =

SD t Coin Door Power Interlock Switch

Back Door Power Intericok Switch

FIGURE 1-3 INTERLOCK SWITCH & MEMORY PROTECT SWITCH

1.5.3 SELF TEST SWITCH There are two (2) Self Test Switches and four (4) positions, located on the inside of Coin Door. See Figure 1-4. The ‘“ZOOKEEPER”™ game is capable of testing itself and provides data to demonstrate that the games circuitry and the controls are working properly. For further information on the Self Test Procedure refer to Section 1.8 and Figure 1-7.

we | FIGURE 1-4 SELF TEST SWITCHES on SWITCH FUNCTION | Up Reset To Factory Setting (Reset Line Lit) Increment Number (Variable Line Lit) Down Decrement Number Advance Sub-Test | Move To Next Line Advance Test _|Move To The Next Screen TABLE 1-1 SELF TEST SWITCHES

1.5.4 VOLUME CONTROL SETTING The Volume Control Setting is located on the Data/Sound P. C. Board, which is on the Service Door. The volume increases when turned clockwise as indicated in Figure 1-5. A second volume control can be found on the inside right of the Coin Door frame. The volume increases when turned as indicated in Figure 1-5.

S d Spi

FIGURE 1-5 VOLUME CONTROL SETTING

1.5.5 SERVICE OUTLET A Power Recepatacle has been provided to further aid servicing. The voltage at this receptacle will be the same as the line voltage the game is set at.

1.6 ELECTRONIC ACCEPTORS This game is equipped with the capability of using 12 VDC Electronic Coin Acceptors, such as Third Wave Electronics, Model TW12 or equivalent. Power for these units may be obtained from the Coin Entry Lamp terminals which provide 12 VDC.

1.7 GAME INSTALLATION Open the Coin Door and pull out the Interlock Switch.Turn the game on.See Figure 1-3. The location name frame should be displayed. If the game is in the game mode, push the Self Test switch toward ADV Sub Test. The game will go into Self Test. If after a minute, the switch test frame is not displayed, refer to the Manual on Self Test (Figure 1-8). After the Switch Test is displayed push the Self Test Switch toward ADV four more times. Then the frame location name should then be displayed. Push Self Test Switch toward ADV Test four more times the game should be in the game mode. For more information on the options the operator can use, see Section 1.8.17 thru 1.8.21.

Page 10

1.7.1 GAME ADJUSTMENTS There are several adjustments you can preform to make the play easier or more difficult. High Score Duration is the length of time the high score will appear on the screen. This is the column to the left. The column to the right is best keeper ever and this remains the same. Maximum Coins defines a limit for the machine, which when crossed will disable the coin slots. This will allow the location to set a limit on the amount of games a player will get if there is a line of people waiting. This value ranges from 1 to 99. However, it should not be set so close to 99 that a single coin can overflow the credits issued (maximum 99). A Free Play mode may be selected by setting maximum credits to 0. Number of Keepers this setting regulates the number of initial Zookeepers which can be set anywhere from 1 ot 99. High Score Enable if set at 1 high score enable will appear if set at 0 none will appear. Attract Sound - If the setting is set a 1 the game will have attract sound, if set a 0 there will be no attract sound. Game Mode - If this setting is set at 1 the game will be in the

ei Table Mode, if set to 0 the game will be in the Upright

lode. Novice Animals - This setting regualtes the speedof the animals and ranges from 1 to 99. 99 being fasest setting. Novice animals appear on screens 1 thru’ 5. Expert Animals - This setting regualtes the speed of the animals and ranges from 1 to 99. 99 being the fastest setting. Expert animals appear on screens 6 thru 10. No Hit Mode - If set a 1 the game will be in the No Hit Mode If set a 0 the game will be in the normal game mode. This setting is useful when servicing to advance to higer screens. Free Game Rate - It ranges from 0 to 99, with the number indicating how many games must be played before a ‘Free Game”’ bonus object will appear in a game. The 0 position disables free games. The unit is in the 0 position when recieved from the factory.

1.8 SELF TEST PROCEDURE 1.8.1 GENERAL The Self Test Procedure is performed using the two (2) Switches located on the right inside corner of the Cabinet, and the Self Test Button and the LED'S on the Video PC Board. (See Figure 1-7).

FIGURE 1-7 SELF TEST BUTTON 1.8.2 ENTERING INTO THE SELF TEST MODE To enter the Self Test Mode, press the Advance Sub-Test Switch located on theCoin Door or the Self Test Button found near the LED display on Video Board. All the LED'S should blink on and the Hardware Tests should start. If a continual test of the Video Board is desired, press the Self Test Button twice to start the Video Test in the Auto Test Mode. In this mode, the machine will continually run the Hardware Test until powered off. If the message “OPEN COIN DOOR TO TEST” appears, the Coin Door must be opened or a jumper connected across J19, 1-2. This is because the CMOS RAM Test cannot be perfomed with the memory protected by the Coin Door Switch.

1.8.3 HARDWARE TESTS These tests are performed in the following order: VIDEO BOARD. DATA BOARD. | ROM Checksum ROM Checksum Communications RAM Local RAM CMOS RAM Communications RAM Color RAM Handshake Test Screen RAM

TABLE 1-2 HARDWARE TESTS All LED values are shown Left to Right. 0 is OFF, 1 is ON and X is dependant upon the test results.

1.8.4 VIDEO BOARD ROM CHECKSUM The Rom Checksum calculates the checksum of each Video ROM and compares it to the checksum stored for that ROM. If it differs from the stored value, the machine will halt and the value of the ROM with the bad checksum will be shown on the LED'S.

LED VALUES: TEST IN PROGRESS: — 00 0001

FAILURE: 01 XXXX

LED VALUE VIDEO 2732

01 0000‘AQO0-AFFF*U3
01 0001BO00-BFFF*U4
01 0010AQ00-AFFFUS
01 0011B000-BFFFUs
01 0100C000-CFFFU7
01 0101D000-DFFFus
01 0110E000-EFFFug

Lot o1tt FO00-FFFF Ut0 “Alternate ROM Bank. TABLE 1-3 VIDEO BOARD ROM CHECKSUM

If the Checksum ROM is bad, it will show U10 to be bad first. If this test fails, the ROM indicated on the LED display or the supporting circuits will need to be replaced.

1.8.5 COMMUNICATIONS RAM FROM VIDEO BOARD The Communications RAM Test determines the stability of memory shared by the two processors by storing a predefined series of numbers throughout the RAM, then reading it back to insure that it was stored correctly. LED VALUE: 00 0010 A failure has been detected when the machine halts with the above display. Failure of Communications RAM during Video Board Tests may result from either defective RAM circuitry or failure of the Data Board. To isolate the failure, disconnect the Data Board at P6 and re-enter the test. A failure means trouble in U3, U4 or associated circuits. Passing the retest suggests Data Board problems.

Page 11

1.8.6 VIDEO BOARD CMOS RAM After saving values in another portion of memory, the CMOS RAM is tested in the same manner as the Communications RAM. If the CMOS RAM passes the test, all of the locations are restored to their previous values.

LED VALUE: 00 0011

A failure of the CMOS RAM has been detected when the machine halts with the above LED value displayed. If this occurs U85 and U86 or associated decoding should be checked.

1.8.7 VIDEO BOARD COLOR RAM This tests the system Color RAM by storing predefined sequences of numbers in the Color RAM, then reading them back while testing for accuracy.

LED VALUE: 00 0100

A failure is indicated by the processor halting with the above value displayed on the LED’S. This signifies the need to check U56, U57 and associated multiplexing and decoding.

1.8.8 VIDEO BOARD SCREEN RAM The Screen RAM is tested by writing a pattern to each page on the screen. The results of these writes is then compared to the original pattern. Any discrepancy causes the machine to halt with the LED displaying the faulty RAM.

LED VALUE: TEST IN PROGRESS: 00 0101

FAILURE: 1X XXXX

LED VALUE | RAM11 XXXXRAM
10 0000U3311 0000U66
10 0001U3211 0001U65
10 0010U31 -11 0010U64
10 0011U3011 0011U63
10 0100U2911.0100U62
10 0101U28110101U61
10 0110U2711.0110U60
10 0111U26110111U59
10 1000U1711 1000U48
10 1001U1611 1001U47
10 1010U1511 1010U46
10 1011u1411:1011U45
10 1100U1311 1100U44
10 1101u1211.1101U43
10 1110ut11.1110u42
101111U10411111U41

TABLE 1-4 VIDEO BOARD RAM CHECKSUM

Upon failure of a screen RAM, locate the problem RAM and replace it. Exchange suspected RAM with a known good location to determine if the problem moves with the RAM IC or whether the problem is in the supporting circuitry, further testing can be done with the Color Bar Test. If this Diagnostic appears to halt without indicating a RAM failure (00 0101 on LED’S), a failure to begin the next test (Data Hardware) is indicated. The interconnection to the Data Processor must be in place and the Data Processor must be functional to continue. SELF TEST LEDS

00 0000

o TEST BUTTON . J

FIGURE 1-7 VIDEO BOARD (ON BACK SERVICE DOOR) 1.8.9 DATA/SOUND BOARD SELF TESTS DATA HARDWARE (ROM CHECKSUM) The ROM Checksum calculates the checksum of each Data ROM and compares it to the checksum stored for that ROM. If it differs from the stored value, the machine will halt and the value of the ROM with the bad checksum will be shown on the LED'S. LED VALUE: TESTIN PROGRESS: 00 0110

FAILURE: 01 XXXX

LED VALUE DATA 2732

01 10008000-8FFFU12
01 10019000-9FFFU13
01 1010A000-AFFFU14
01 1011B000-BFFFU15
01 1100C000-CFFFU16
01 11010000-DFFFu17
01 1110E000-EFFFU18
011414FOOO-FFFFU19

TABLE 1-5 DATA/SOUND BOARD ROM CHECKSUM

If this test fails in the field, the bad ROM will need to be replaced.

NOTE: To aid the technician in diagnosing difficult boards, hold the Self Test Button located on the Video Board depressed while the game is being powered on. This will cause the game to enter the diagnostic mode directly upon power up, accessing only one ROM per processor. Games which otherwise will not execute the on

hoard diagnostics will thereby provide more information on ROM

jailure.

1.8.10 DATA/SOUND BOARD LOCAL MEM@RY The Data processor uses a known sequence of numbers to test the bits in its Local Memory. If a bad bit is found the machine will halt with the following display. LED VALUE:

1.8.11 COMMUNICATIONS RAM ADDRESSING The function of this test is to ensure that both the Data and the Video Processor address the Communicatons RAM in the same manner. The Data Processor requests the Video Processor to fill the RAM with a known pattern then, the Data Processor compares the result to the expected pattern. If it does not match, one of the processors is probably decoding the address incorrectly as the RAM itself was previously tested for stability by the Video Processor. The machine will halt with the following display.

LED VALUE: 00 0111

00 1000

Page 12

1.8.12 DATA/VIDEO HANDSHAKE This test ensures that the Data Processor can send priority commands via interrupts to the Video Processor. The Video Processor is halted, then restarted by the data Processor after the proper command acknowledgements are received. The machine will halt with the following display.

LED VALUE: 00 1001

1.8.13 SWITCH TEST This screen is used to determine all switches are working order before entering the switch dependent self-test screens. The Wiring Diagram supplied with each game will indicate the number associated with a particular switch. The switch numbers appear in green if the switch is closed and white if it is open. The Advance Test Switch (Switch number 9) is always red in order to set it apart from the others on the screen, switch 29, 30, 31, 32 are not used & stay green. The user should check all other switches before pressing the Advance Test Switch, as this would Move him to the next screen. In addition to the switches required, by the game, the User should be sure to test the Advance Sub-Test, UP and DOWN Switches located on the Coin Door, these switches are used to move about in the Self-Tests Screens. To advance to

the a screen, activate the Advance Test Button located on the

Coin Door.

GAME OVER

ADVANCE SUB-TEST ‘ADVANGE SELF TEST oven

[seneen paw } a0 01011 nae Leo's

SCREEN Tests

com S101 PRogeamuine

GAME OVER

FIGURE 1-8 FLOW CHART

1.8.14 COLOR BALANCE AND INTENSITY ADJUST SCREEN This screen is comprised of two sections. The first section provides a method for adjusting the intensity level of each color gun, and achieving an initial color balance. Three squares, one blue, one green and one red, are drawn along the top of the screen at minimum intensity or brightness. The color guns should be adjusted so that these squares are barely visible and of equal intensity. To complete the color adjustments, a gray scale is provided at the bottom of the screen. Fine tune the color balance with this ~ scale, the double check that the squares at the top are barely visible. To advance to the next screen, activate the Advance Test Switch located on the Coin Door. 1.8.15 COLOR BARS The CPU divides the screen RAM into 16 areas corresponding to 16 bars on the screen. Each area is written with a data value from the Table 1-7. Each value exercises one bit in the screen RAM. The Color RAM is written with a pattern which outputs each data value with a recognizable color from the table. All other data values are coded black. This results in a normal screen of 16 colors bars per the following Figure.

SSH RSC * A Sa 2 Rw SS a wy wS.cho NON CON 2 OS ree Ng PP cs S

COLOR BAR DIAGNOSTIC NORMAL FIGURE 1-9 COLOR BAR

BLK BLU BLK

P PoP 0% 0 0° “ NS PF cM o> 0% 6% Ao, wt ON AN ss RC os ON x oy ws

  • s Ser seo a noe Oe Sos s ‘. os aS SOOFF SFFFF

COLOR BAR DIAGNOSTIC BIT 03 STUCK LOW IN 1-BANK FIGURE 1-10 COLOR BAR

Page 13

SCREEN RAM DATA CONTENT —____A FR oO 0.6% GP Pgh a Oy par > o> OOP GOLEM AAP LON AS AS ASN 0840 SA en eos CP 0% 0% 0% oO AP OTOP ANAS Ay AS AP LoN AN AS POP OP OF OP OO OP AP AN AN AY AN AN AN AO GS cS N 4.

SOOFF

SFFOO

COLOR BAR DIAGNOSTIC BIT 5 STUCK HIGH ALL BANKS.

FIGURE 1-11 COLOR BAR SS) SCREEN RAM CONTENT COLOR RAM ADDRESS

Bar #| Color Hex Binary Bit Tested

1|Red01 | 000000010
2 | Orange02 | 000000101
3 | Yellow04 | 000001002
4 | Green08 | 000010003
5 | Blue Green10 | 000100004
6 | Blue20 | 001000005
7 | Violet40|010000006
8 | White80 | 100000007
9 | RedFE| 1114111100
10 | OrangeFD | 111111011
11| YellowFRO}411110112
12|GreenF7} 411101113
13 | Blue GreenEF| 1110141114
14 | BlueDF | 110111115
15 | VioletBF | 101111116
16 | White7F{O11111117

None | Black XX | XXXX__XXXX

TABLE 1-6

If the Self-Test passes, errors in those circuits which affect CPU access are ruled out. This leaves latches U91, U94, shift registers U95, U96 and U105-109, direction select U81 and U104 and the CR side of select U81 and U104 and CR side of the Color RAM MUX U55, U73, and U74. Stuck bits may be indentified by observing abnormal bars. A bit stuck high will result in black bars (two bit high) on the left or top half of the screen except for the bar associated with the stuck bit. On the right of bottom half, the bar associated with the stuck bit will be black. The converse is true of a bit stuck low. ‘An error across the entire bar indicates an error in the shift registers, direction select, or color RAM MUX which affects every pixel. Lines of error running crosswise to the bars indicate an error in one bank of RAM if every eighth pixel. To move to the next screen, activate the Advance Test Button. If self test fails, the color bars still may by useful. This screen may now be entered without going through on-board self test. Use “Advance Test’’ to enter the high score screen then ‘‘Down’’ to enter the Switch Test. Advance Test may then be used to access color bars. 1.8.16 ALIGNMENT AND CONVERGENCE TEST This screen is provided to align the color guns and correct the convergence ‘on the screen. The screen is composed of a white grid. Adjust the screen width and length so that the rectangle is slightly within the boundaries of the tube. The adjustment is to be made on the center of the lines which make up the rectangle. The corners of the rectangle will extend beyond the shadow mask. Agrid of white squares is provided to help detect and correct any convergence problems the tube may have. Adjust the monitor until the squares are of equal size throughout the screen. To advance to the next screen, activate the Advance Test Button on the Coin Door.

n

Page 14

1.8.17 LOCATION NAME This screen allows the user to program the location name. Alpha, numerical and miscellaneous charecters are provided. Use the Advance Sub-Test Button to move to the next character position indicated in green. Use the UP/DOWN switch to reach desired character, set by depressing Advance Sub-Test Button. Continue until location name is completed, depress Advance Test Button to advance to next screen.

1.8.18 LOCATION PROGRAMMING This screen allows the location to define various game control parameters. The User selects the line to be changed by using, the Advance Sub-Test Button until the desired line is changed to green. The value associated with this line is then modified with the UP or DOWN switches. If the machine is to be reset to the factory setting, use the Advance Sub-Test Button until the reset line is lit in green, the press the UP switch. The values will be reset and the user will be placed back on the first line for further adjustments. Advance test will move to the next screen at any time. Refer to Para 1.7.1 for setting.

1.8.19 HIGH SCORE TO DATE SCREEN This screen shows the scores and initials of the players with the ten highest scores. It is used as an audit for the game. To reset the values, press the UP Switch. This will also set the initials to the default values. When the UP Button is activated it resets to default scores. To Move to the next screen, activate the Advance Test Button in the bottom right inside corner of cabinet.

1.8.20 AUDIT TOTALS This screen provides the audit totals for the game. Once they are recorded, they may be zeroed by pressing the UP Switch. The following audits are kept.

Total Credits The total number of paid credits issued. This total is never zeroed, but it will wrap around to zero when its total reaches 1,000,000. The only time this total can be zeroed is by physically removing the battery or jumper W1, while the power is off. The number of coins dropped into the left slot. The number of coins dropped in the center slot. The number of coins dropped into the right slot. The number of credits issued for coins. The number of credits awarded by the game. Awarded credits / paid credits + awarded credits *100 Number of minutes the game has been in play mode. Number of minutes the game has been in extended or awarded play. % Free Time Awarded minutes / minutes played *100. Average Game (Sec) | Minutes played / paid credits + awarded credits “60 The number of times which a player scored high enough to bump someone else from the high score list. Left Coins

Center Coins

Right Coins

Paid Credits Awarded Credits

% Free Plays

Minutes Played

Minutes Awarded

High Scores

12 TABLE 1-7 AUDIT TOTALS The UP Switch is used to zero the audits. To advance to the next screen, activate the Advance Test Button on the Coin Door. Total credits will not turn to zero unless battery voltage is removed from CMOS memory.

1.8.21 COIN SLOT SELECTION This screen allows the user to either select a standard coinage setting for the game or program his own. If a standard setting is desired, use the UP and DOWN Switch to adjust the coinage setting while itis litin green. The values for the variable will change as this number is altered. When the right selection is set, use Advance Test to return to the game. If a non-standard setting is desired, use Advance Sub-Test Switch to move down to the variables so that they may be programmed individually. Once this switch is pressed, the standard setting number is set to zero to show that the location has supplied their own settings. As the lower variables are unchanged, the user may minimize his effort by first selecting a setting close to the one he desires. Once in the programming mode, the Advance Sub-Test Switch is used to move among the variables. It will also take you back to the standard settings, if you press it by mistake. The UP and DOWN Switches are used to increment or decrement the values. Advance Test Switch will return to the game when pressed. The coin multiplier tells how many coin units are issued for each coin through a particular slot. Coin units for credit show the number of units necessary before a credit is issued. Coin units for bonus gives the number of units necessary before a bonus credit is issued. Minimum coin is an optional value which will keep the credits from accumulating until the specified minimum amount of coin units is reached. It is not used in any of the standard settings.

1.8.22 CMOS MEMORY FAILURE If the message ‘‘Memory Failure - Service Required’’ appears on the screen, the CMOS RAM which stores all of the location programming has failed. All the values stored in the RAM are set back to factory defaults. This condition probably indicates a battery failure, or a failure of U85 or U86. Refer to Section 2 on Maintenance 2.7.6 CMOS RAM.

Page 15

STANDARD COIN SETTINGS TABLE 1-8

ae 2/elele

zvlse|/8/8/2)2] & 8/8/slze;2l2/ &|3|él#|s|s |e COIN DOOR MECHANISMS CREDIT/MONEY

STANDARD1/.25, 4/81Ot | 01 | 04 | OF | 01 | 00 | 00

1/.50, 3/81, 6/82 t 02 | 01} 04 | 01 | 02 | 04 | 00 1/.50 03 | O01 | 04 | O1 | 02 | 00 | 00

10M, 5 DM1/1DM, 6/50M04 | 06 | 00 | 01 | 01 | 00 | 00
1 FRANC, 5 FRANC1/2F, 3/5F ONLY05 | 01}16 | 06 | 02]00 | 00
25 CENTS, 1 GUILDER1/25, 4/1G06 | 01 | 00 | 04}01}00 | 00
5 FRANCS, 10 FRANCSV/5F, 2/10F07 | 01}00 | 02 | 01 | 00 | 00
4/1 0F08 | 01 | 00 | 02 | 02]00 | 00
1 FRANC, 2 FRANCQF, 5/2F09 | 00 | 04 | 01 | 04}00 | 00
1 UNIT, 5 UNITS1/2, 3/510 | 01 | 00 | 06 | 02 | 00}00
TWIN COIN1/1 COIN01 | 01 | 04 | 01 | O1 | 00 | 00

[12 coins 03 | 01 | 04 [ 01 | 02 | 00 | 00

CUSTOM COIN SETTING TABLE 1-9

Bls

ry2=
2|/2/s/E/5)8)3

g/s|e;/8]/s]s]s

nl]al!<ec2a2
els}s8)s|/e]ez]§

3/8) e];z]/2le]

&|3/8|2|8]sl=

COIN DOOR MECHANISMS CREDIT/MONEY

STANDARD1/.25, 5/1oo | o1{ofo1[or | 04]00
2.50, 5/1oo | or {| o4[or]or04 | 02
2/50, 471oo | or {| 04]orf]or | oo [| 02
17.50, 391, 491.25oo {| o3 | 12]03 | 04]15 | 00
| ¥/.50, 3/1, 7782oo]12[48]12[14]96 | 24
25 CENTS, 1 GUILDER1/.25, 5/16oo | o1{00 | o4|o1|o4[00
100 LIRE, 200 LIRE1/200 LIREoo]or | oo | 02]o2[00 | 00
TWIN COIN1/3 COIN, 2/500 [02[00 J 02{05 | 00 | 00
1 UNIT, 5 UNITS1A, 5/5oo { or { oo | 05]o1|00 | 00
173, 25oo | o2{oo | 10]o5[oo | oo |
Page 16

Maintenance

ALL GAMES REQUIRE A CERTAIN AMOUNT OF MAINTENANCE TO KEEP THEM IN GOOD WORKING ORDER. A PERIODIC CHECK OF THE MECHANICAL CONTROLS WOULD BE BENEFICAL TO THE SUCCESS OF YOUR GAME.

Page 17
  • MAINTENANCE AND REPAIR 2.1 CLEANING The exterior of the game, all metal parts and all plastic parts can be cleaned with a non-abrasive cleanser. Caution should be used when cleaning the glass, a dry cloth can cause scratches and result in a foggy appearance.

2.2 COIN DOOR The Door used in “‘ZOOKEEPER’’™ UPRIGHT game needs little or No maintenance, See Figure 2.1. If desired a special coin mechanism cleanser, that leaves no residue, can be obtained from your distributor. Refer to the manufacturers documenation of additional information is needed.

FIGURE 2-1 COIN DOOR

2.3 FUSE REPLACEMENT This game contains eight (8) fuses. Five (5) fuses can be found on the Regulator PCB and two (2) can be found on the Transformer Assembly. One (1) fuses is located at the bracket where the AC line cord comes into the cabinet. See Figure 2-2 for locations of these fuses.

FIGURE 2-2 FUSE REPLACEMENT 2.4 MONITOR REMOVAL If you need to remove the Video Monitor, follow the instructions listed below:

CAUTION It is recommended the game be left disconnected for at least one hour before removing the Video Monitor. This will probably discharge the Video tube but EX- TREME CAUTION is still necessary.
  • Disconnect power from the line voltage.
  • Remove the Control Panel by releasing the two spring loaded latches. . Disconnect the Wiring by separating connector V and all wire to the CRT. . Remove (2) rear carriage bolts and lower Monitor on side rails.
  • Remove (4) bolts, one on each corner of the Monitor Bracket, slide Monitor out toward you. sk Oo
CAUTION Use EXTREME CAUTION and do not touch electrical parts of the Monitor Yoke area with your hands or with any metal object in your hands! High voltages may exist in any Monitor, even with power disconnected.

FIGURE 2-3 MONITOR REMOVAL

CAUTION
Caution must be used with a degaussing coil so the Magnetic field of the degaussing coil is not allowed to become too intense at any on place on the picture tube thereby causing a localized color distortion.

If you move the game to another location after degaussing the problem may reappear. Refer to Monitor Manual 72-00035-001 for further details.

Page 18

2.5 COVER GLASS REMOVAL To remove the Cover Glass follow the instructions listed below:

  • Remove the control panel by reaching up through the Coin Door and unlatching the latching clamps.
  • Remove the (3) Screws on the Cover Glass Bracket.
  • Hold Glass firmly slide out from the rear.
  • Be sure you are holding the glass firmly to ensure against any chipping or breakage.

FIGURE 2-4 COVER GLASS REMOVAL

2.6 PRINTED CIRCUIT BOARD REPLACEMENT You may wish to remove ‘‘ZOOKEEPER’'™ printed circuit board, Video Processor (08-00001-001), Data/Sound Board (08-00122- 001), ROM/IO Board (08-0003-001), Coin Door Processor (08- 00039-006) or Video Extension Board (08-00112-001) for servicing. Refer to Figure 2-5. “ZOOKEEPER’’™ Printed Circuit Boards (PCB) are located on the inside of the service door for easy access. To remove the boards the following steps should be followed:

  • Open the Service Door, the power will automatically be removed by the Interlock Switch located on the inside of the door frame. . Disconnect the connectors from the boards. Remove nuts from around shield and lift off shield. . Disconnect the ribbon cable, connecting the boards by spreading eject latches on the connector. . Remove the screws for the boards you wish to remove. a RON
  • Be. er . FIGURE 2-5 PRINTED CIRCUIT BOARD

2.7 POWER SUPPLY The Power Supply produces all the necessary game voltage requirements. Refer to Figure 2-6 and the Power Supply Schematic while reading the following circuit description.

FIGURE 2-6 POWER SUPPLY

2.7.1 AC INPUT The AC Input Voltage is applied to the main Power Supply via the AC Line Cords, Line Filter, Line Fuse, Power Switch and Interlock Switch. Different Line Cord are used for 120V and for 240V. The Line Fuse is located on the Line Cord Assembly near the Strain Relief. A Voltage Programming Block is located on the primary side of the Transformer to compensate for high/low voltage conditions. The following line voltages may be inserting the appropriate Programming Plug.

LINE VOLTAGE LINE FUSE

100 VAC + 10%50/60Hz3 AMP
120 VAC + 10%50/60Hz3 AMP
200 VAC + 10%50/60Hz1.5 AMP
220 VAC + 10%50/60Hz1.5 AMP
240 VAC + 10%50/60Hz1.5 AMP

TABLE 2-1 LINE VOLTAGE

Page 19
CAUTION For continous protection against fire hazard, replace only with a fuse of the same type having the same electrical rating.

There are five secondary sources. Three go to the Regulator PCB source voltage for +5VDC, +12VDC, -12VDC, and —5VDC. The other two are fused 6.3VAC used for the incandescent lighting and fused 120VAC used for the monitor, and in certain models for a fluorescent lamp and fan. These secondary fuses are located on the bracket adjacent to the Power Transformer.

Secondary Fuse 2.0AMP SLO-BLO 2.5AMP Circuit 120VAC 6.3VAC

TABLE 2-2 SECONDARY FUSES

2.7.2 —SVDC AND —12VDC REGULATORS The AC Input for the negative voltages comes into the Regulator PCB on J1-5 and J1-6 from the Transformer. Fuse F3 protects against short circuits. The AC voltage is then full wave rectified by BR3 and filtered by C16. The raw DC is then applied to Reg 1, a three terminal —12V Regulator. The output of this Regualtor is the —12VDC output for the system and is also the input voltage for Reg 2, a —5V Regulator. The output of this Regulator is the —SVDC for the system. Capacitors C17, C18, C19 are to improve the transient response and stability of the minus voltage regulator. Diodes D8 and D9 provide protection against C18 and C19 being shorted through the Regulator. Resistors R34 and R35 provide current limiting for LED'S 3 and 4 which will light when there is voltage present at the regulation outputs.

2.7.3 +5VDC REGULATOR The AC Input for the +5VDC Regulator circuit comes in on J1-1 and J1-2, via F1 into BR1. BR1 full wave rectifies the AC Input. This raw DC is applied to the collectors of (2) series pass transistors, mounted on the Heat Sink Assembly. The regulation is done by U3, which is a voltage regulator whose output controls the gain of Q5, which in turn controls the gain of the series pass transistors. The emitter of the series pass transistor returns to the Regulator PCB and through R11 and R12, which serve to force current sharing between the series pass devices. The voltage at the output of R11 and R12 is the +5VDC for the system. R16 and R18 are voltage set and current foldback adjustments respectively. Q8, D3 and R20 comprise a SCR-Type Crowbar Circuit which will trigger when the DC output voltages rise above 5.8V. Once the SCR fires, the Power Supply has to be turned off to reset the device. R19 is a current limiter for the voltage indicator LED 1. R16 is used to set the output voltage of the Regulator. C8, D2, R13 and Q4 delay the start-up of the 5V Regulator to allow the —5VDC Regulator to stabilize first. 2.7.4 +12VDC REGULATOR This circuit is essentially the same as the 5V Regulator described above. The AC current comes in on J1-3 and J1-4, via fuse F2 into BR2. The AC is rectified by BR2 and filtered by C9. The raw DC is fed to a single series pass transistor on the Heat Sink Assembly and also powers the +12V and +5V Regulator. R28 and R25 are voltage set and current foldback and factory adjusted to 12 Volts +.25V at 4 AMPS. D7, Q9, and R31 are SCR Crowbar Circuits which trigger at 13VDC output which causes supply to go into current foldback. There is an RC delay as in the 5V circuit to delay the +12V rise time.

2.7.5 RESET CIRCUIT The reset circuit will output a 2sec active low MRST pulse at J3-14 and J4-14 when the power is first turned ON and whenever power fails for more than 35ms. The reset circuitry is comprised of a Dual Timer (556) and an optical coupler across an AC secondary. The output of U1 is the input to one half of the 556 which is configured as a missing pulse detector. C1 and R3 determine the time before the output goes active. This is set for about 35ms. When two or more cycles are missing, the output of the first timer triggers the second timer which drives the MRST low for about 2 seconds. The timer constant for the second timer is set by R4 and C6. Power on reset is generated by C4, and R39 and D12 on the trigger input of the second timer. Q3 inverts the signal out of the 556 so it is active low. R7 insures MRST is low while the power is rising.

2.7.6 POWER SUPPLY ADJUSTMENTS VOLTAGE Adjust voltage on +5V and +12V for +5.00V to +5.05V and +12.00V to +12.05V. CURRENT LIMIT Adjust control (51, 121) counterclockwise until voltage just changes then turn control clockwise until voltage goes back to original value. With pointer, mark position of arrow on potentionmeter then turn control until beginning of 1st notch is aligned with the pointer. On the controls with the Blue Disk turn approximately 30°.

FIGURE 2-7 CURRENT LIMIT ADJUSTMENT

If voltage adjustment will not bring voltage up, set current limit adjustment to 2 value.

Page 20

2.8 CMOS RAM \f when powering the game up, it will not coin up because the battery is low. The following procedure should be followed. Open the Service Door of the game and pull out Interlock to Power game back up. Pull out the W1 jumper next to the battery on the Video Board (Blue jumper). Push Interlock back in. Wait 2 minutes, power back on and insert W1 back in. If the Location Name frame does not come on the CRT, remove W1 again and power down. Short pins 18 and 9 on U85, power back on and insert W1 back in. Leave the game on for 12 hours. If this procedure does not work when you turn the game back on the battery may need to be replaced.

2.9 TEST POINTS The following is a list of Test Points to be used when troubleshooting.

DATA/SOUND

DTP1E(Master Clock)
DTP2Q(Master Clock)

DTP3 LC Last Interlock Complete

DTP4SA 15(Address Line)
DTP5DA 15(Address Line)

DTP6 Voice Clock

DTP7SBSC(Sound Processor Data Enable)
DTP8DBSC(Data Processor Data Enable)

OTP10 +5V OTP11 Ground

TABLE 2-3 DATA/SOUND BOARD TEST POINTS

VIDEO BOARD

VTP1 Invert

VTP2 10 MHZ

VTP3va(Clock Video Processor)

VTP4 VE (Clock Video Processor)

VIPS Luc Last Instruction Complete

VTP6 Busy

VTP7 VBSC (Video Data Enable)

VIP8VA 15(Address Line)

TABLE 2-4 VIDEO BOARD TEST POINTS

If you ground any Data Enable Test Point (DTP7, DTP8, VTP7) the related processor will receive No-OP Instructions and the address line will act line a 16 Bit Counter.

Page 21

Operation

THIS SECTION PROVIDES A TECHNICAL DESCRIPTION OF “ZOOKEEPER’™ GAME. THE GAME ELECTRONICALLY CONSISTS OF PRICTED CIRCUIT BOARDS, TV MONITOR, POWER SUPPLY, AND SPEAKERS WHICH ARE DESCRIBED IN DETAIL IN THE FOLLOWINT TEXT.

Page 22
  • THEORY OF OPERATION 3.1 GENERAL The TAITO AMERICA CORPORATION'S arcade video system game is an advanced multiprocessor based circuit utilizing the Motorola 6809E microprocessor. The system is organized in three logical blocks:

A. The Data Processor, which supervises the operation of the entire system. B. The Video Processor, which performs all screen based functions, such as playfield image motion, line drawing, etc. C. The Sound Processor, which generates sounds under the direct control of the Data Processor.

In order to facilitate easy inter-system communications, the Data and the Video Microprocessors run synchronously using clock and timing signals developed on the Video Board. For this reason, discussion will begin by examining the Video Board.

3.2 VIDEO BOARD 3.2.1 SYSTEM CLOCK The fundamental system clock is developed by the 20MHz crystal, inverters U24 and U39, and components. The 20MHz signal is divided by the high speed flip flop U38 to obtain a 10MHz main clock with a precise 50 percent duty cycle. This 10MHz signal generates all other fundamental timing signals for the video system, including the Data Processor. 1C23 divides the 10MHz signal to obtain 5MHz, 2.5MHz and CCLK, and their respective inversions. IC’s U9, U37, and U38 combine these signals, presenting them to U25, which synchronizes the output signal to the system 10MHz clock. This circuit produces waveforms whose active edges are synchronized to 15ns worse case, 2ns average. The characteristics of the clock circuit may be noted by reference to the Timing Diagram, Figure 3-1.

ewe i 1} 4

ome|-|=\i.

sea TP i

cox=fiels Ged clade ed ola lel Ga Oo cy coy

@ ij > +L i . + t veo

mOTEif

i a

uxF:
a1f

os ws As oms +} +. mms =

easeiTyt

FIGURE 3-1 CLOCK TIMING 3.2.2 SCREEN RAM The Video Processor controls a Screen RAM of 256 x 256 pixels with 8 bits per pixel. In order to access of this information, the screen is divided into two pages, top and bottom, chosen under software control. These pages are both addressed at 0000 - 7FFF with address 0 corresponding to the lower left corner of the screen (horizontal scan). All CRT accesses to this RAM are transparent to the processor and the RAM may be read or written any time. The timing of the Screen RAM and the eventual scan is controlled by a 6845/6545/46505 CRT Controller Chip. It's address outputs are gated by U19, U20, U50, and U51 for inversion when when a cocktail table mode. The scan addresses are multiplexed with the address present on the microprocessor data bus by U35, U52, U53, and U54 for standard RAS-CAS accessing. The desired bank of memory is addressed by U87, a one of four decoder. Data written into the Screen RAM comes directly from the system data bus, buffered by 33 Ohm resistors. If a processor read is taking place, the data is placed on the data bus by U77, U78, U79, and U80. Screen reads are latched by 374’s U91, U92, U93, and U94. A second screen read is then performed, and this data, together with the data from the screen read previously performed and latched by the 374's is presented to the eight (8) 74LS299 shift registers. These registers may be shifted in either direction for cocktail table implementation. The byte stream then proceeds to the Color RAM.

ADDRESS | VIDEO BOARD MEMORY MAP

A.| 8000Dual Port RAM
B.| 8400CMOS Battery Backup Memory
C.| 8800LED Output and Color RAM Page Select

8801 EPROM Page Select D. | 8C00 Data FIRQ Activation Address 8001 Video FIRQ Deactivation Address

E.| 9000Color RAM
F.9402Address Latch Hi-Byte

9403 Address Latch Lo-Byte 9400 Address Latch Indexed Screen Location 9800 Scan Line Readback Location 9co0 CRT Controller Base Address

TABLE 3-1 VIDEO BOARD MEMORY MAP

3.2.3 DUAL PORT RAM This RAM may be accessed in its entirety by either processor. This is arbitrated as follows:

  • The Data Processor runs in quadrature with (one quarter clock cycle ahead of) the Video Processor. In other words, E is inverted for use as DQ, and Q becomes DE. Refer to Timing Diagram. Figure 3-2.
  • The Data Processor, by nature of this timing, accesses the Dual Port RAM % cycle before the Video Processor. At this point the Video Processor is guaranteed to not be accessing the RAM. The Data Processor access is flagged by U36, which causes a cycle to be stolen from the Video Processor’s main clock, VQ and VE.
  • The Video Processor is unable to access the Dual Port RAM unless the Data Processor is not accessing it as it will not be receiving clocks during that time. The cycle steal is accomplished by the generation of signal DPMUX by U36. This signal directly steals the cycle, and also folds over multiplexers U5, U6, and U21, switching the address lines, R/W and gating signals. U1 and U2 gate the data to or from the desired processor. U22 insures that no spurious writes are generated during foldover.
Page 23

savers mene ¢ < rm i p v i FIGURE 3-2 DUAL PORT RAM TIMING

3.2.4 CMOS RAM The CMOS RAM is implemented for use as both a battery back-up storage area and a work area for the Video Processor. The gating U100, U101, U102, and U103 insure that writes to the block RAM from $8700 - 87FF cannot be performed unless the Coin Door is open (J19-2 grounded). The 3.6V NiCAD battery is trickle charged by Q8, R64, and R65 when the system is powered. When turned off, supply current for U85, U86, and U100 is provided by this battery. U100 is included to solidly gate the MRST signal and prevent invalid operations during power Up and Down. LED and Color RAM Page Latch, U72 is addressed at address $8800. The upper six bits drive LED'S on the circuit board for diagnostics which cannot be done through the screen. The lower 2 bits select the Color RAM page and will be discussed later.

3.2.5 BI DIRECTIONAL FIRQ CAPABILITY To provide for immediate inter-system communication on demand a Bi-Directional FIRQ Capability has been provided. Any access of address $8C00 by the Video Processor will generate a FIRQ to the Data Processor. Any access of $8C01 by the Video Processor will remove a FIRQ generated by the Data Processor to the Video Processor. This is accomplished by U7, U8, and U9.

3.2.6 COLOR RAM The Color RAM is used as a translation matrix so that a number of different pixel values may access a given color, or to change the color of a given area of the screen without rewriting the Screen RAM. The serial bit stream, eight bits wide, comes from the shift registers of the Screen RAM to be presented to multiplexers USS, U73, and U74. These select between the Video Processor bus and the serial bit stream. As processor access times are considerably greater than the basic bit time (200ns), it is necessary to access this register only during retrace times. Bus read/write occur through U75, and serial output is latched by U76. This Data Stream is converted to a color pallet of 64 colors and four intensities. When the serial bit is selected for access, the two high order bits are provided by the LED output latch. This allows the Programmer to select between four pages of RAM rapidly. 3.2.7 ADDRESS LATCH CIRCUITRY Two methods of Screen Memory Address are provided:

  • A 16 bit address may be written into latch U70 and U71 addressed at $9402 and $9403. The addressed location may be accessed by reference to location $9400.
  • The high order bit of the latch selects one of two pages which may be directly addressed by reference to locations $0000 - $7FFF. U36, U70, and U71 latch the address. U36 is used in conjunction with U70 as U70 and U71 are tri-stated when inactive. The screen address deposited on the LA bus by U84 and U98 for Processor Bus accesses, and by U70 and U71 for latched address. Decoding is performed by U87 and U88.

3.2.8 SCAN LINE READBACK When read, this location is the number of the scan line currently being drawn by the beam. U34 latches the last row address drawn, and U101 prevents erratic updating at the end of a horizontal line. There are 256 valid scan lines 00 - FF.

3.2.9 CRT CONTROLLER The 6845/6545/46505 is a software programmable sync and scan generator. It has two ports based at $9C00 and $9C01. It is recommended that the reader consult Motorola, Hitachi, Rockwell, or Synertek supplied documentation. Register initialization are as follows:

INITIALIZATION REGISTER] DESCRIPTION (DECIMAL)

ROHorizontal total-138
R1Horizontal displayed32
R2Horizontal sync position34
R3Sync pluse width03
R4Vertical total-131
RSVertical hold adjust11
R6Vertical displayed30
R7Vertical sync position31
RQScan lines per row-107

TABLE 3-2 REGISTER INITIALIZATION

All other registers are cleared. The interlace capability which differentiates the various types is not used in this application.

3.3 DATA/SOUND BOARD The Data Processor runs synchronously to the Video Processor, as was described in this (Section Dual) Port Memory. All basic timing signals originate on the Video Processor Board and are bussed onto the Data Processor Board. The Sound Processor and Amplifier circuitry also resides on this Board.

Page 24

3.3.1 MEMORY MAP The following devices are available for access to the Data Processor.

$0000 | Dual Port Memory $0400 | Local Memory $0800 | ACIA Base Address $0C00 | Video FIRQ Activation Address $0C01 | Data FIRQ Deactivation Address $1000 | Sound PIA $1400 | Game PIA 1. $1900 | Game PIA 2. $1000 | Game PIA 3. seopE

xmoamm

TABLE 3-3 DATA/SOUND MEMORY MAP

3.3.2 DUAL PORT MEMORY See discussion of Dual Port Memory under Video Processor Heading (Section 3.2).

3.3.3 LOCAL MEMORY This is a 1K block of memory, U15 and U16, provided for scratch and work area for the Data Processor.

3.3.4 ACIA A Motorola 6850 ACIA has been provided for diagnostic and other communications. Timing is generated by crystal oscillator Y1 - U23 and prescaled by U27 and U26. SW1 may be configured to allow one of eight baud rates (2 speeds may be software selected in the ACIA). Correct RS-232 levels are provided by U25 and U21.

3.3.5 BI-DIRECTIONAL FIRQ CAPABILITY Any access of $8C00 will generate a FIRQ to the Video Processor. Any access of $8C01 will remove FIRQ generated by the Video Processor to the Data Processor. This is accomplished by U7, U8, and U9, which resides on the Video Board.

3.3.6 SOUND PIA Both ports of PIA U20 have been dedicated to the control of the Sound Processor. Port A is used to select a sound number, which is initiated by strobbing the U20 (CA2) - U8 (CA1) interrupt line. Responses can be made using the reverse U8 (CA2) - U20 (CA1) interrupt. Port B is used to control the amplitude of the generated sound to two Stereo Amplifiers. The output of side B go to U24 and U28, which vary the ratio of the voltage divider across the noninverting inputs of U29 and U30. This allows spatial positioning of a sound to coincide with real time events occuring on the screen, as well as a time based envelope control.

3.3.7 GAME PIA’S Three 6820's are provided for interfacing with Play Controls and Coin Door Switches. These are located on the Game Board and are accessed through a Jumper Cable J16 and J15 respectively. 3.3.8 SOUND PROCESSOR A Motorola 6802 also resides on the Data Board for sound generation. This Processor runs at 3.68MHz and accesses only two devices, PIA’S U7 and U8. U8 as mentioned previously, interface to the Data Processor. It also is the digital to analog output of the Sound Processor. Data from Port B is presented to U13. The current based output is converted to a voltage output by Q1, and controlled in amplitude by a potentiometer placed across J8. Speech circuitry is mixed with sound by R9, and the sum is sent to the Amplifiers. U7 controls the speech synthesis chip U19. The speech signal is shaped and filtered by the multipole bandpass filter U18.

3.4 ROM//0 BOARD This board contains the Program ROM for both the Data and Sound Processors, along with the PIA’S needed to interface control, coils, lamps, etc.

3.4.1 GAME PIA’S Three Game PIA’S are located on this board $1400, $1900, $1000. These devices, U11, U20, and U30 respectively, interface through noise control circuits A or B filters for those lines dedicated to inputs. Eleven (11) High Current Drivers have been provided utilizing circuit C. Each of these is capable of switching a 1.5AMP/ 24Volt DC load to ground.

3.4.2 ROM'S Eight ROM locations are provided for the Data Processor, U12 - U19. These are selected by U21. ROM select jumpering for 2732's is as follows: Pin 2-14, 3-13, 4-12, 5-11, and 6-10. The highest address EPROM is U19, or U27 in each bank with addresses of adjacent sockets progressing downward in $1000 byte blocks. ROM Bank U12-U19 contains 2732 EPROMS as selected by the jumper plug at U22. ROM Bank U25-U27 also contains 2732 EPROMS as selected by the jumper plug at U28.

E-PROM BANK LOCATION DATA U22 SOUND U29

TABLE 3-5 DECODING JUMPER LOCATION

3.5 VIDEO ROM BOARD This Board contains the program ROM for the Video Processor. 16K of memory is paged over address $A000-$BFFF. Setting Bit 2 at $8801 selects page 1 while resetting the bit selects page 0.

3.5.1 ROM’S Eight ROM locations U3-U10 contain 2732 EPROMS.

Page 25

&

Parts Lists

Page 26

INCANDESCENT PANEL

TAITO ITEM PART NO. DESCRIPTION 1 27-00006-001 | Lamp 47 2 26800009-001| Bayonet Base Socket 3 61D00112-001} Marquee Lighting Plate

Page 27

8-WAY JOYSTICK

TAITO PART NO. DESCRIPTION

63-00031-001 Ball & Shaft (Short) 63-00033-001 Mask

63-00027-001 Mounting Plate 62-00002-001 Shock Mount Pad

63-00028-001 Switch Plate

63-00030-001 Actuator

61-00078-001 “L" Bracket

63-00026-001 Switch Spacer 29-00016-002 Leaf Switch

63-00029-001 Spacer 59B00020-017 “E” Ring

Page 28

CONTROL PANEL

] TaITO item | PARTNO. —_| DESCRIPTION 63B00031-001 | Ball & Shaft 63B00024-001 | Push Button White 42B00108-001 | Cleat, Wood 63D00032-006 | 8-Way Joystick 61A00015-001 | Strike Hook 1] 42000017-001 | Control Panel, Wood 61D00251-001 | Control Panel, Metal 63-00137-001 | Lexan, Decal welolwlola}alolrm}a 63-00025-001 | Switch Support 10 54A07001-008 | Nut, Stamped %-11 1 29B00016-001 | Leaf Switch “Item not shown on drawing

11 10

Page 29

DOOR ASSEMBLY

TAITO ITEM PART NO. DESCRIPTION 1 04-00037-002 | Lock Kit 2 61-00306-001 | P.C.Board Mounting Plate 3 08-00117-001 | Game P.C. Board Assembly . 79-00067-001 | L.E.D. Values Sheet 5 08-00001-001 | Video Board 6 08-00003-001 | ROM/I/0 Board 7 08-00002-003 | Data/Sound Board 8 08-00039-006 | Coin Processor Board 9 08-00112-001 | Video ROM Expnsion 10 61-00142-001 | Lock Rod Assembly 1 61-00111-001 | Bracket, Lock Rod 12 61-00306-001 | P.C.B. Mounting Plate “Item not shown on drawing

Page 30

TAITO |

TEMPART NO.DESCRIPTIONREFERENCE
107-00027-001 | Inner Panel With Levers Sub Assembly404429
294-03013-001 | Nut #8-32400-8
  • 09-00017-001 | Custom Harness Assembly (SHL Coin) i 09-00017-002 | Custom Harness Assembly (Dual Coin) 3 61B001 13-001] Service Switch Bracket 4 29-00022-001 | Service Switch 5 54-03011-001 | Nut #4-40
663-00014-001 | Switch Cover904762
751-02052-001 | Screw #6-32 x %/16 SS ph100-6-3
823-00001-001 | C.R.E.M. Coil Assembly404354
951-02052-001 | Screw #6-32 x */x6 SS ph100-4-12
1059-00019-001 | Retainer900651
a28-00029-001 | Silver Switch Wire for U.S. 25¢904710-1
1229-00007-001 | Switch904845
1361-00044-001 | Coin Chute904701
1461-00045-001 | Coin Return Box904598
1561-00025-001 | Switch & C.R.E.M. Coil Bracket404428
1659-00018-001 | 25° Acceptor5301-10
1751-02051-006 | Screw 4-40 x 3 SS ph110-4-6
1827-00003-001 | Miniature Bayonet Base Lamp.904717

a 26-00006-001 | Lamp Socket

1927-00003-001 | #47 Lamp (6.3 Voit)904716
2061-00048-001 | Coin Inlet Chute904418
2161-00047-001 | Right Half of Coin Inlet Chute904594
2254-00001-001 | ‘“U'’ Type Fastener904712
2351-02051-006 | Screw 4-40 x % SS ph116-4-8
2429-00006-001 | Slam Switch Assembly904704

25 998325 Coin Meters

"Item not shown on drawing.

Page 31

COIN DOOR

Page 32

CABINET ASSEMBLY FRONT VIEW

TAITO ITEM PART NO. DESCRIPTION 1 07M00055-004 Incandescent Panel 2 63B00006-003) ‘'U’ Channel Bracket 3 47-00012-016} Marquee 4 61000115-001} Marquee Retaining Bracket 5 61D00012-001| Lower Coverglass Bracket 6 07-00251-001} Control Panel Assembly 7 07-00115-001 | Coin Door 8 61-00113-001 | Switch Bracket bs 59-00045-001 | Switch Barrier, Single 9 07M00057-001 Service Switch Assembly 10 29-00022-001| Slide, Center Return Switch 11 29B00015-001| Interlock Switch 12 61B00114-001| Interlock Switch Bracket 7 59-00046-001 | Switch Barrier, Double 13 59-00008-001 | Latching Clamp 14 63B00002-004| ‘‘T’’ Molding 15 29A00023-001} Power ON/OFF Switch 16 [ 41-00023-001 | Finished Cabinet

Page 33

CABINET ASSEMBLEY FRONT VIEW

Page 34

CABINET ASSEMBLY REAR VIEW

TAITO ITEM PART NO. DESCRIPTION r 1 07-00083-001 | Speaker Assembly 2 61B00009-001 | Speaker Grill 3 41-00023-001 | Finished Cabinet 4 63-00053-001 | Monitor Shroud 5 47-00016-007 | Coverglass 6 07M00042-001) A/C Line Cord Assembly

  • 22-00001-001 | Line Filter 7 61B00030-002 | Interlock Bracket 8 29800015-001 | Interlock Switch 9 07M00039-001} Transformer Assembly . 08-00007-001 | Regulator, PCB
  • 18-00003-001 | Transformer [- 61-00208-001 | CRT Support Frame 10 61C00054-001 | Cash Box Lid WW 31-00004-001 | 19" Color Monitor 12 63-00019-001 | Cash Tray Separator = 13 61B00039-001 | Cash Tray Handle 14 61D00060-001 | Cash Box 15 63R00010-001 | Cash Tray (only) [is 07M00054-001| Cash Tray Assembly 7 7 08-00002-003 | Data/Sound P.C.B. 18 08-00003-001 | ROM/O P.C.B. 19 To4-00037-002 Lock Kit [0 08-00001-001 | Video Processor P.C. B. 21 41-00014-004 | Back Door 22 45€00002-001 | Lock Assembly 23, 61B800142-001 | Lock Rod Assembly 24 61A00111-001 | Lock Rod Bracket 25 63-00143-001 | Shield 26 61-00208-001 | CRT Support Frame 27 61-00006-001 | Upper Coverglass Bracket 28 26-00008-001 | Socket Lamp 29 27-00006-001 | #47 Bulb 30 61-00306-001 | Ground Plate
Page 35

CABINET ASSEMBLY REAR VIEW

Page 36

POWER SUPPLY COMPONENT LAYOUT Om as Lae, “= ac om aD Ge)

a rm iS om O8 Y

  • om O oO, @ Or

eee. 08-00007-O0! iss.¢ MADE IN U.S.A.

Page 37

POWER SUPPLY

TAITO TAITO SYM | PART NO. DESCRIPTION SYM | PART NO. DESCRIPTION

R111-00001-102 | Resistor 1.0K 5% VW 5%C5 | 12-10001-102 | Capacitor, .00tuf

R2 | 11-00001-512 | Resistor 5.1K %4W 5% C6 |} 12-30001-106 | Capacitor, Tantalum 10uf R3 | 11-00001-183 | Resistor 18K %W 5% C7 | 12-20003-509 | Capacitor, Electrolytic 50,000uf R4 | 11-00001-224 | Resistor 220K %W 5% C8 | 12-30001-105 | Capacitor, Tantalum 1.uf 35V

RS177-00001-020Resistor 2ohm ¥4W + 5%co12-20003-209 | Capacitor, Electrolytic 20,000uf

R6 | 11-00001-222 | Resistor 2.2K %W 5% C10 | 12-10001-332 | Capacitor, Ceramic .0033ut R7 | 11-10001-101 | Resistor 100K %4W 5% C11 | 12-30001-476 | Capacitor, Tantalum 47uf R8 | 11-00001-102 | Resistor 10K ¥sW 5% C12 | 12-30001-105 | Capacitor, Tantalum 1.uf 35V RQ | 11-00001-472 | Resistor 4.7K %4W 5% C13 | 12-10004-103 | Capacitor, Ceramic .O1uf [R10 |11-10001-101 | Resistor 100K YW 5% | C14 | 12-10001-102 | Capacitor, .001uf R11 | 11-30001-015 | Resistor .15 4W 5% C15 | 12-30001-476 | Capacitor, Tantalum 47uf R12. | 11-30001-015 | Resistor .15 4W 5% C16 | 12-20002-108 | Capacitor, Electrolytic 1,000ut R13 | 11-00001-472 | Resistor 4.7K YW 5% C17 | 12-30001-225 | Capacitor, Tantalum 2.2uf 25V R14 | 11-00001-222 | Resistor 2.2K Y4W 5% C18 | 12-30001-225 | Capacitor, Tantalum 2.2uf 25V R15 | 11-00001-222 | Resistor 2.2K %4W 5% C19 | 12-30001-105 | Capacitor, Tantalum 1.uf 35V

R16 | 11-60001-252 | Pot 2.5K ¥4W 20%Ft24-00003-010 | 10A Fuse

R17 | 11-00001-222 | Resistor 2.2K Y4W 5% F2 — | 24-00003-010 | 10A Fuse R18 | 11-60001-102 | Pot 1.0K %4W 20% F3 | 24-00003-003 | Fuse, 2A

R19 | 11-00001-511 | Resistor 510K %W 5%F424-00003-004 | Fuse, 4A

R20 | 11-10001-470 | Resistor 47K eW 5% F5 | 24-00003-004 | Fuse, 4A R21 | 11-00001-162 | Resistor 1.6K YW 5% BR1 | 13-00100-025 | Diode Bridge 25A, 100V R22 | 11-00001-103 | Resistor 10K YW 5% BR2 | 13-00100-012 | Diode Bridge 12A, 100V R23 | 11-00001-472 | Resistor 4.7K Y4W 34 BR3 | 13-00100-002 | Diode Bridge 2A, 100V R24 | 11-00001-222 | Resistor 2.2K Y4W 5% D1 | 13-14002-001 | Diode IN4002 R25 | 11-60001-102 | Pot 1.0K %W 5% D2 | 13-14002-001 | Diode IN4002 R26 | 11-00001-472 | Resistor 470K Y4W 5% D3 | 13-10752-001 | Diode, Zener IN4002 R27 | 11-00001-222 | Resistor 2.2K Y4W 5% D4 | 13-14002-001 | Diode IN4002 R28 | 11-60001-252 | Pot 2.5K %W 20% D5 | 13-14002-001 | Diode IN4002 R29 | 11-00001-472 | Resistor 4.7K 4W 5% DG | 13-14002-001 | Diode 1IN4002 R30 | 11-00001-122 | Resistor 1.2K YaW 5% D7 | 13-10964-001 | Diode, Zener IN4002 R31_ | 11-10001-470 | Resistor 47K vaW 5% D8 | 13-14002-001 | Diode IN4002 R32_ | 11-30001-015 | Resistor .15K 4W 5% D9 =| 13-14002-001 | Diode IN4002 R33_ | 11-00001-222 | Resistor 2.2K Y4W 5% D10 | 13-14002-001 | Diode IN4002 R34 | 11-00001-122 | Resistor 1.2K Y4W 5% D11_ | 13-14002-001 | Diode IN4002 R35_ | 11-00001-511 | Resistor 510 Y4W 5% D12 | 13-14002-001 | Diode IN4002 R36 | 11-00001-222 | Resistor 2.2K YW 5% D13. | 13-16276-001 | Transorb (IN6276) R37_ | 11-00001-104 | Resistor 100K D14 | 13-16281-001 | Transorb (IN6281) R38 | 11-00001-103 | Resistor 10K YW 5% D15 | 13-14002-001 | Diode IN4002

R39_|11-00001-224 | Resistor 220L YW 5%D16 | 13-14002-001 | Diode IN4002

C1 | 12-30001-225 | Capacitor, Tantalum 2.2uf 25V D17 | 13-16267-001 | Transorb (IN6267) C2 | 12-10064-103 | Capacitor, Ceramic .O1uf LED1 | 13-00001-001 | LED (Red) C3 | 12-10004-103 | Capacitor, Ceramic .01uf LED2 | 13-00001-001 | LED (Red) C4 | 12-30001-105 } Capacitor, Tantalum 1.uf 35V LEDS | 13-00001-001 | LED (Red) | LED4 | 13-00001-001 | LED (Red) |

Page 38

POWER SUPPLY

TAITO SYM | PART NO. DESCRIPTION U1 15-62500-001 | Opto Coupler H11AA2 U2__|15-50556-001 | Timer (Dual) 556 U3 | 15-50723-001 | Voltage Regulator 723 U4 | 15-50723-001 | Voltage Regualtor 723 REG1 | 15-57912-001 | Voltage Regualtor 7912 REG2} 15-57905-001 | Voltage Regualtor 79L05 Q1__| 14-22905-001 | Transistor 2N2905 Q2 | 14-22905-001 | Transistor 2N2905 Q3 | 14-22905-001 | Transistor 2N2905 Q4 | 14-22905-001 | Transistor 2N2905 Q5 | 14-23055-001 | Transistor 2N3055 Q6 | 14-22905-001 | Transistor 2N2905 Q7 _|14-20030-001 | Transistor TIP-30A Q8 | 14-26401-001 | SCR 2N6401 Q9 | 14-26401-001 | SCR 2N6401 Jt |25-00022-006 | Connector, 1-380999-0 6Pin J2 | 25-00022-008 | Connector, 350212-1 8Pin J3___|25-00002-014 ; Connector, 09-60-1141 14Pin v4 25-00002-014 | Connector, 09-60-1140 14Pin 24-10001-001 Fuse Clips 30-00220-002 Heat Sink Dual To-220 30-00003-001 Heat Sink Single To-3

Page 39

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 40

VIDEO PROCESSOR

TAITO TAITO PART NO. DESCRIPTION SYM | PART NO. DESCRIPTION 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80 -20% C55 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80: —20% C2 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% C56 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% C3 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% C57 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% C4 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% C58 | 12-10002-104 | Capacitor Ceramic, .1uf,S0V, +80/—20% C5 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% C59 | 12-10002-104 | Capacitor Ceramic, .tuf,50V, +80/—36 C6 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/-20% C60 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% C7 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/-20% C61 | 12-30001-106 | Capacitor Tant, 10uf, 16V C8 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% C62 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/-20% C9 | 12-30001-106 | Capacitor Tant, 10uf, 16V C63 | 12-30001-106 | Capacitor Tant, 10uf,16V C10 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% C64 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% C11 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% C65 | 12-10001-471 | Capacitor Ceramic, 470uf,50V,10% X7R G12 | 12-10002-104 | Capacitor Ceramic, 1uf,50V, +80/—20% Axial Lead C13 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% C66 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20%

C14 | 12-10003-101 | Capacitor Ceramic, 100pf, 10% NPO Axial Lead|C67_|12-10002-104 | Capacitor Ceramic, tuf,50V, +80/—20%

15 | 12-10002-104 | Capacitor Ceramic, .tuf,50V, +80/—20% C68 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20%

C16 | 12-10002-104 | Capacitor Ceramic, tuf,50V, +80/—20%C69_|12-10002-104 | Capacitor Ceramic, Tuf,50V, +80/—20%

12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% C70 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/-20% 42-10002-104 | Capacitor Ceramic, tuf,50V, +80/~20% C71 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% 42-10002-104 | Capacitor Ceramic, .1uf.50V, +80/—20% C72 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% C20 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% C73. | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% 21 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% C74 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% 22 | 12-30001-106 | Capacitor Tant, 10uf, 16V C75 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/-20% 623 | 12-10002-104 | Capacitor Ceramic, .1uf,S0V, +80/-20% €76_|'12-10002-104 | Capacitor Ceramic, tut, SOV, +80/— 20%

626 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/-20%CTT_|12-30001-106 | Capacitor Tant, 10uf, 16V

27 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% C78 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/-20% 28 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% C79 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/-20%

629 | 12-10002-104 | Capacitor Ceramic, uf,50V, +80/— 20%C80_|12-30001-106 | Capacitor Tant, 10uf,16V
€30_[12-10002-104 | Capacitor Ceramic, 1uf,50V, +80/— 20%C81_|12-10002-104 | Capacitor Ceramic, 1uf.50V, +80/-20%

31 | 12-10003-101 [Capacitor Disk 100pf, 10% NPO C82 | 12-10002-104 | Capacitor Ceramic, uf,50V, +80/~20% 632 _| 12-10002-104 | Capacitor Ceramic, 1uf,50V, +80/-20% C83 _| 12-10002-104 | Capacitor Ceramic, -tuf,S0V, + 80/— 36

€33_|12-10002-104 | Capacitor Ceramic, tuf,50V, ~60/—20%C84 _| 12-10002-104 | Capacitor Ceramic, tuf.60V, +80/—20%
€34 | 12-10002-104 | Capacitor Ceramic, .tuf,50V, +80) —20%685_|12:10002-104 | Capacitor Ceramic, uf,50V. +80/-20%

35 | 12-10002-104 | Capacitor Ceramic, .1uf.50V, +80/-20% C86 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—-20% 36 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% C87 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80) ~ 20% 637 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% C88 | 12-20001-107 | Capacitor Electrolytic, 100ur,25V,

GOBTE 1000210 | Cabacior Geta. TUL AV. + S020a9 | 12-20001-107 | Capacitor Electrolytic, ‘00ut.25V,

C39 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/~20% +100/—20% C40 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% C90 | 12-20001-107 | Capacitor Electrolytic, 100uf,25V, C41 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% +100/-20% C42 | 12-10002-104 | Capacitor Tant, 10uf, 16V C91 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20%

C43 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20%C92_|12-10002-104 | Capacitor Ceramic, .tuf,50V, +80/~20%

C44 | 12-30001-106 | Capacitor Tant, 10uf,16V C93 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% C45 | 12-30001-106 | Capacitor Tant, 10uf. 16V C94 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% C50 [12-10002-104 Capacitor Ceramic, .1uf,50V, +80/—20% C95 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/-20% | C51 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% C96 | 12-10001-471 | Capacitor Ceramic, 470pf,50V,10% X7R 52 | 12-10002-104 | Capacitor Ceramic, uf,50V, +80/—20% ——

63 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20%Go|2-100 1-471Cepacton Ceramic} A7Apl.20h 10% Xn

C54 | 12-10002-104 | Capacitor Ceramic, 1uf.50V, +80/—20% C98 | 12-10001-471 | Capacitor Ceramic, 470pt,50V, 10% X7R Axial Lead

Page 41

VIDEO PROCESSOR

TAITO TAITO | SYM | PART NO. _| DESCRIPTION | SYM | PART NO. | DESCRIPTION C99 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/-20% R37 | 11-00001-473 | Resistor 47K OHM, YsW, 5% {C100 12-10002-104 | Capacitor Ceramic, .tuf,50V, +80/—20% R38 | 11-00001-332 | Resistor 3300 OHM, YW, 5% C101] 12-10003-100 | Capacitor Ceramic, 10pf, 10% NPO Axial R39 | 11-00001-331 | Resistor 330 OHM, %W, 5% boat. 20% R40 | 11-00001-331 [Resistor 330 OHM, “AW, 5% C102] 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/~20% R41 | 11-00001-331 | Resistor 330 OHM, ‘aw, 5% 103] 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% R42 | 11-00001-331 | Resistor 330 OHM, %W. 5% 104] 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% R43 | 11-00001-331 | Resistor 330 OHM, %W, 5% 105] 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/-20% R44 | 11-00001-331 | Resistor 330 OHM, MW, 5% C106] 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% R45 | 11-00001-471 | Resistor 470 OHM, YaW, 5% C107 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/-20% R46 | 11-00001-820 | Resistor 82 OHM, %W, 5% C108} 12-10002-104 | Capacitor Ceramic, -luf,50V, +80/—20% R47 | 11-00001-471 | Resistor 470 OHM, %W, 5% C113] 12-10001-471 panel elas SOV, 10% 470PF R48 | 11-00001-181 | Resistor 180 OHM. YW, 5% e_ | 11-0000 152} Resistor 7 A ft | 11-00007-330 [Resistor 33 OHM, TW, 5% R3_[1-0000%-271 | Resistor 270 OFM. Mh, R52 | 1-00001-990 [Resistor 39 OHM, YAW, 5%

R4_|11-00001-271 | Resistor 270 OHM, %W, 5%aea*tai-onoo7-a00 | Resistor 3 CAMA 5a

R5__ | 11-00001-271 | Resistor 270 OHM, YW, 5% aia | it onbi a0 TReasior 33 OAM AW. 5%

BoEnos PeeleR55 | 11-00001-330 | Resistor 33 OHM, TW, 5%
RY_|11-00001-22 | Resistor 220 OFM. fo 6%56 | 11-00001-830 [Resistor 33 OHM, VW, 5%

Bb, | TUDO 22 | Resistor 2h aa RST | 11-00007-330 [Resistor 39 OHM, YW, 6%

Ro _| 11-00001-350 | Resistor 38 OM. HAW. Se68|11-G000T-S80 | Resistor 39 OHM, HW, 5%
io | tS eea59|17-00007-473 | Resistor 47K OHM, TaW, 5%
BL | 11-0000 Seti Rests SOHN a60]11-0000%-332 [Resistor 3300 OHM, AW, 5%

B21 IT Dogo seth Resistor Se i | 17-00001-307 | Resistor 390 OHM, TaW, 5%

R13. | 11-00001-820 | Resistor 82 OHM, %4W, 5%mezn.bn0ni sao8l Resistor 2R aS
R14 | 11-00001-181 | Resistor 180 OHM, 14W, 5%feaLeonor 02 Resistor KW, 53

R16 | 11-00001-271 | Resistor 270 OHM, MW, Sie R64 | 11-0000t-121 | Resistor 120 OHM, YW, 5% R16 | 11-00001-471 | Resistor 470 OHM, %W, 5% Res 1 T-boonT-11 ReaeiGr TaD OHM “oh

Ri7 | 11-00001-471 | Resistor 470 OHM, YW, 5%més171-00007-339 | Resistor 3.3K aie
iaR67 | 11-00001-330 | Resistor 3300 OHM, YAW, 5%
R19. | 11-00001-181 | Resistor 180 OHM, YW, 5%Rea{-11-00007-330 | Resiclor 3.3K oe

R20 | 11-00001-820 | Resistor 82 OHM, YW, 5% ago 111 B000-332 | Resistor ae uw oe

R21 | 11-00001-330 | Resistor 33 OHM, YaW, 5%Ferfazowonoor Tae =

R22 | 11-00001-330 | Resistor 33 OHM, YW, 5% ego" | avcononr-ont [irarte bead

R23 | 11-00001-330 | Resistor 33 OHM, YW. 5%feafri7-omorom.| Fanie Bead
R24 | 11-00001-330 | Resistor 33 OHM, YW. 5%caanla7-pnaot-b0T | Fantie Bead
R25 | 11-00001-330 | Resistor 33 OHM, YW, 5%Fas47-00001-007 [lFemtie Bead
R26 | 11-00001-330 | Resistor 33 OHM, YW, 5%spe177-00007-001 [Ferrite Bead
R27 | 11-00001-330 | Resistor 33 OHM, YW, 5%a7}17-c0n01-001 | fanite ead

R26 | 11-00001-181 | Resistor 180 OHM, ¥4W, 5% soe 1 77-00001-007 | Fanite Bead

R29 | 11-00001-471 | Resistor 470 OHM, ¥%4W, 5%a5[17-00002-007"| Fernieleead

R30 | 11-00001-471 | Resistor 470 OHM, %W, 5% aval aponot-an | Farts Bead R31 | 11-00001-471 | Resistor 470 OHM, YW, 5% ; R32 | 11-00001-471 | Resistor 470 OHM, YW, 5% B14 17-00001-001 | Ferrite Bead

Raa111-00001-471 | Resistor 470 OHM, %uW, 5%Q1 | 14-23904-001 | Transistor NPN Silicon (2N3904)
faa111-00001-681 | Resistor 680 OHM, %W, 5%Q2 | 14-23904-001 | Transistor NPN Silicon (2N3904)
a5111-00001-397 | Resistor 390 OHM, %W, 5%Q3come Transistor NPN Silicon (2N3904)
Rabeaeesse 33 OHM, AW, 5%Q4 | 14-23904-001 | Transistor NPN Silicon (2N3904)

a”

Page 42

VIDEO PROCESSOR

TAITO PART NO. DESCRIPTION DESCRIPTION Transistor NPN Silicon (2N3904) 15-10001-001 | RAM 16K x 1 Dynamic (4116)

14-23904-001{Transistor NPN Silicon (2N3904)26-00001-016 | Socket DIP 16 Pin for U11

Transistor NPN Silicon (2N3904) 15-10001-001 | RAM 16K x 1 Dynamic (4116) Transistor NPN Silicon (2N3905) 26-00001-016 | Socket DIP 16 Pin for U12 L.E.D. RED, TL-1% 15-10001-001 | RAM 16K x 1 Dynamic (4116) L.E.D. RED, TL-1% 26-00001-016 | Socket DIP 16 Pin for U13

13-00001-001|L.£.0. RED, TL-1%U14 |15-10001-001 | RAM 16K x 1 Dynamic (4116)

L.E.D. RED, TL-1% 26-00001-016 | Socket DIP 16 Pin for U14

LEDS | 13-00001-001|L.E.D. RED, TL-1%U15 75-10007-001 | RAM 16K x 1 Dynamic (4116)

26-00001-016 | Socket DIP 16 Pin for U15 LEDG | 13-00001-001 {L.E.D. RED, TL-1% U16 |15-10001-001 | RAM 16K x 1 Dynamic (4116) 19-00003-001 [CRYSTAL, 20,000MHZ BATT | 20-00001-001 | Battery, NICAD, 3.6V, 1/3 AA 26-00001-016 | Socket DIP 16 Pin for U16 U17 |15-10001-001 | RAM 16K x 1 Dynamic (4116) SW1 |29-00017-001 | Switch Momentary

TP1|59-00021-001 | Test Point26-00001-016 | Socket DIP 16 Pin for U17

59-00021-001 | Test Point U18|15-00003-001 | CRT CONTROLLER 68A45 59-00021-001 | Test Point 26-00001-040 | Socket DIP 40 Pin for U18 59-00021-001 | Test Point U19 | 15-20086-001 | Quad 2 Input Exclusive or (74LS86) |TP5_{59-00021-001 | Test Point U20 | 15-20086-001 | Quad 2 Input Exclusive or (74LS86)

TP6|59-00021-001 | Test PointU21 |15-20157-001 | Multiplexer Quad 2-Input (74LS157)
TP7|59-00021-001 | Test PointU22 | 15-20032-001 | Quad 2 Input or (74LS157)
TP8|59-00021-001 | Test PointU23 |15-20161-001 | Counter, 4 Bit Presetable (7415161)
RP1|11-50001-102 | 1K OHM Resistor Sip Pack|U24 | 15-20004-001 | Inverter, HEX (74LS04)
RP2|11-50001-473 |47K OHM Resistor Sip PackU25 | 15-70374-001 | Latch, Octal Shockey (74LS374)

RP3 | 11-50001-332 |3.3K Resistor Sip Pack U26 | 15-10001-001 | RAM 16K x1 Dynamic (4116)

RP4|11-50001-332 |3.3K Resistor Sip Pack26-00001-016 | Socket DIP 16 Pin for U26
RP5|11-50001-332 |3.3K Resistor Sip PackU27 | 15-10001-001 | RAM 16K x1 Dynamic (4116)

25-00001-014 | Connector, 14 Pin .156 Center 26-00001-016 | Socket DIP 16 Pin for U27 25-00002-014 | Connector, 14 Pin .156 Center U28 | 15-10001-001 | RAM 16K x1 Dynamic (4116) 25-00001-001 | Connector, 50 Pin Header Vertical 26-00001-016 | Socket DIP 16 Pin for U2B 25-00001-001 | Connector, 50 Pin Header Vertical U29 | 15-10001-001 | RAM 16K x1 Dynamic (4116) 25-00002-002 | Connector, 2 Pin .156 Center 26-00001-016 | Socket DIP 16 Pin for U29 [wi [25-00021-002 Connector .1 Center for W1 U30 | 15-10001-001 | RAM 16K x1 Dynamic (4116) | Wi |26-00007-001 | Shorting Pin 26-00001-016 | Socket DIP 16 Pin for U30

'32-00001-001|P.C.B. Video Processor BoardU31 | 15-10001-001 | RAM 16K x1 Dynamic (4116)
U1|15-20245-001 | Bus Transiciever, Octal (74LS245)26-00001-016 | Socket DIP 16 Pin for U31
U2|15-20245-001 | Bus Transiciever, Octal (74LS245)U32 | 15-10001-001 | RAM 16K x1 Dynamic (4116)
U3_|15-10003-001 | Ram 1K x 4 NMOS Static (2114)[26-00007-016 Socket DIP 16 Pin for U32

}26-00001-018 | Socket DIP 18 Pin for U3 U33 | 15-10001-001 [RAM 16K x1 Dynamic (4116)

U4|15-10003-001 | Ram 1K x 4 NMOS Static (2114)26-00001-016 | Socket DIP 16 Pin for U33

126-00001-018 | Socket DIP 18 Pin for U4 U34 | 15-20374-001 | Latch, Octal (745374) & 15-20157-001 | Multiplexer Quad 2-Input (74LS157) U35 | 15-20153-001 | Multiplexer, Dual 4-Input (74LS153) 15-20157-001 | Multiplexer Quad 2-Input (74LS157) U36 | 15-20074-001 | Flip Flop Dual-D (74LS74) 15-20074-001 | Flip Flop, Dual D (74LS74) U37 | 15-20008-001 | Quad, 2-Input and (74LS08) }15-20032-001 | Quad 2 Input or (74LS32) U38 | 15-70113-001 | Flip Flop JK Schottky (74LS113) 15-20032-001 | Quad 2 Input or (74LS32) U39 | 15-20004-001 | Inverter, HEX (74LS04)

U10 |15-10001-001{RAM 16K x 1 Dynamic (4116)U40 | 15-30017-001 | Buffer/Driver, HEX (7417)

| __ [26-00001-016 [Socket DIP 16 Pin for U10 Udi | 15-10001-001 | RAM 16K x 1 Dynamic (4116) 26-00001-016 | Socket DIP 16 Pin for U41 a2

Page 43

VIDEO PROCESSOR

TAITO | TAITO

SYM | PART NO.DESCRIPTIONSYM |PART NO.DESCRIPTION
U42| 15-10001-001 | RAM 16K x 1 Dynamic (4116)U81|15-20157-001 | Multiplexer Quad 2-Input (74LS157)

26-00001-016 | Socket DIP 16 Pin for U42 U82 |15-00002-001 |eossr 68A09E U43] 15-10001-001 | RAM 16K x 1 Dynamic (4116) 26-00001-040 | Socket DIP 40 Pin for U82 26-00001-016 | Socket DIP 16 Pin for U43 U83 |15-20244-001 | Octal, Buffer (7415244)

44] 15-10001-001 | RAM 16K x 1 Dynamic (4116)U84 [askOctal, Buffer (74LS244)

26-00001-016 | Socket DIP 16 Pin for U44 U85 |15-10002-001 | RAM 1K x 4 CMOS Static (6514) U45 | 15-10001-001 | RAM 16K x 1 Dynamic (4116) 26-00001-018 | Socket DIP 18 Pin for U85 26-00001-016 | Socket DIP 16 Pin for U45 U86 15-10002-001 RAM 1K x 4 CMOS Static (6514) U46 15-10001-001 | RAM 16K x 1 Dynamic (4116) 26-00001-016 | Socket DIP 16 Pin for U46 U87 15-20139-001 Decoder Dual 1 of 4 (74LS139) ame eee DIP 18 Pin for U86 u47 15-10001-001 | RAM 16K x 1 Dynamic (4116) U88 15-20032-001 Quad 2-Input of (74LS32) 26-00001-016 | Socket DIP 16 Pin for U47 u89 15-20074-001 Flip Flop, Dual-D (74LS74) [15-20004-001

U48 | 15-10001-001 | RAM 16K x 1 Dynamic (4116)U90Inverter. HEX (74LS04)

26-00001-016 | Socket DIP 16 Pin for U48 U91 |15-20374-001 | Latch, Octal (74LS374) U49 | 15-20032-001 | Quad 2-Input or (74LS32) | U92 |15-20374-001 | Latch, Octal (74LS374) U50 | 15-20086-001 | Quad 2-Input Exclusive or (74LS86) U93 |15-20374-001 | Latch, Octal (74LS374) U51 | 15-20086-001 | Quad 2-Input Exclusive or (74LS86) U94 |15-20374-001 | Latch, Octal (74LS374) U52 | 15-20153-001 | Multiplexer, Dua! 4-Input (74LS153) U95 |15-20299-001 | Shift Register 8 Bit (74LS299) U53 | 15-20153-001 | Multiplexer, Dual 4-Input (74LS153) U96 |15-20299-001 | Shift Register 8 Bit (74LS299) U54 | 15-20153-001 | Multiplexer, Dual 4-Input (74LS153) U97 |15-20244-001 | Buffer, Octal (74LS244) U55 | 15-20157-001 | Multiplexer, Quad 2-Input (74LS157) U98 |15-20244-001 | Buffer, Octal (74LS244) 56 | 15-10008-001 | RAM 1K x 4 HMOS Static (2148) U99 |15-20138-001 | Decoder, 1 of 8 (74LS138) 26-00001-018 | Socket DIP 18 Pin for US6 U100}15-40000-001 | Quad 2-Input NOR (74C00) US7 | 15-10008-001 | RAM 1K x 4 HMOS Static (2148) U101/15-20008-001 | Quad 2-Input AND (74LS08) 26-00001-018 | Socket DIP 18 Pin for US7 U102}15-20010-001 | Triple 3-Input AND (741810) U58 | 15-30017-001 | Butfer/Driver, HEX (7417) U103]15-20000-001 | Quad 2-Input NAND (74LS00) U59 | 15-10001-001 | RAM 16K x 1 Dynamic (4116) U104]15-20157-001 | Multiplexer Quad 2-Input (74LS157) U60 | 15-10001-001 | RAM 16K x 1 Dynamic (4116) U105]15-20299-001 | Shift Register 8 Bit (74LS299) U61 | 15-10001-001 | RAM 16K x 1 Dynamic (4116) [ U106}15-20299-001 | Shift Register 8 Bit (74LS299) U62 | 15-10001-001 | RAM 16K x 1 Dynamic (4116) U107|15-20299-001 | Shift Register 8 Bit (741299) U63 | 15-10001-001 | RAM 16K x 1 Dynamic (4116) U108]15-20299-001 | Shift Register 8 Bit (74LS299) U64 | 15-10001-001 | RAM 16K x 1 Dynamic (4116) U109/15-20299-001 | Shift Register 8 Bit (7415299)

U65 | 15-10001-001 | RAM 16K x 1 Dynamic (4116)u110[15-20299-001Shift Register 8 Bit (74LS299)

66 | 15-10001-001 | RAM 16K x 1 Dynamic (4116) U67 | 15-20032-001 | Quad 2-Input or (74LS32) U68 | 15-20244-001 | Octal Buffer (74LS244) U69 | 15-20245-001 | BUS Transciever, Octal (74LS245) U70 | 15-20374-001 | Latch, Octal (74LS374) U71 | 15-20374-001 | Latch, Octal (74LS374) U72 | 15-20374-001 | Latch, Octal (74LS374) U73 | 15-20157-001 | Multiplexer Quad 2-Input (74LS157) U74 | 15-20157-001 | Multiplexer Quad 2-Input (74LS157) U75 | 15-20245-001 | BUS Transciever, Octal (74LS245) U76 | 15-20273-001 | Register 8 Bit (74LS273) U77 | 15-20373-001 | Latch, Octal (74LS373) U78 | 15-20373-001 | Latch, Octal (74LS373) U79 | 15-20373-001 | Latch. Octal (74LS373) U80 | 15-20373-001 | Latch. Octal (74LS373)

Page 44

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 45

DATA/SOUND PROCESSOR

TAITO | TAITO SYM|PARTNO. | DESCRIPTION SYM |PARTNO. | DESCRIPTION Ri | 11-00001-473 | Resistor 47K YaW +5% FB5 | 17-00001-001 | Ferrite Bead R2__ | 11-00001-332 | Resistor 3.3K “MW =5% FB8 | 17-00001-001 | Ferrite Bead

R3__[11-00001-332 | Resistor 3.3K %4W +-5%17-00001-001 | Ferrite Bead
R4_| 11-00001-332 | Resistor 3300 OHM %4W 5%FB10 | 17-00001-001 | Ferrite Bead
[R5| 11-00001-472 | Resistor 4.7K YW +5%FB11 | 17-00001-001 | Ferrite Bead

11-00001-103 | Resistor 4.7K YAW +5% | FB13 | 17-00001-001 | Ferrite Bead 11-00001-103 | Resistor 10K Y4W 5% FB14 | 17-00001-001 | Ferrite Bead 11-00001-332 | Resistor 3.3K OHM 4W +5% FB15 | 17-00001-001 | Ferrite Bead 11-60001-502 | Pot, P.C. Mount 5K FB16 | 17-00001-001 | Ferrite Bead 11-00001-473 | Resistor 47K YW 5% FB17 | 17-00001-001 | Ferrite Bead 11-00001-473 | Resistor 47K YW =5% FB18 | 17-00001-001 | Ferrite Bead 11-00001-332 | Resistor 3.3K Y4W +5% FB19 | 17-00001-001 | Ferrite Bead [R13 | 11-00001-332 | Resistor 3.3K 4W +5% £820 | 17-00001-001 | Ferrite Bead 11-00001-332 | Resistor 3.3K “AW +5% C1 | 12-10002-104 | Capacitor Ceramic .1uf 50V Axial Lead

11-00001-332 | Resistor 3.3K UW +5%2| 12-10002-104 | Capacitor Ceramic . 1uf 50V Axial Lead

11-00001-332 | Resistor 3.3K 4W +5% 3 _ | 12-10002-104 | Capacitor Ceramic .1uf 50V Axial Lead 11-00001-332 | Resistor 3300 OHM YW »5% 04 | 12-10002-104 | Capacitor Ceramic .1uf 50V Axial Lead

11-00001-124 | Resistor 120K %4W +5%5| 12-10002-104 | Capacitor Ceramic .1uf 50V Axial Lead

11-00001-472 | Resistor 4.7K YW +5% C6 | 12-10002-104 | Capacitor Ceramic .1uf 50V Axial Lead R20 | 11-00001-221 | Resistor 220 OHM YW 5% 7 _ | 12-20001-107 | Capacitor Electrolytic 100uf 16V R21 11-00001-221 Resistor 220 OHM Y4W +5% 12-20001-107 Capacitor Electrolytic 100uf 16V R22 | 11-00001-332 | Resistor 3.3K %4W +5% 12-20001-107 | Capacitor Electrolytic 100uf 16V R24 | 11-00001-182 | Resistor 1.8K 4W +5% 12-20001-107 | Capacitor Electrolytic 100uf 16V R25 | 11-60001-104 | POT, P.C. Mount 100K 12-20001-107 | Capacitor Electrolytic 100uf 16V R26 | 11-00001-103 | Resistor 10K “4W +5% 12-10002-104 | Capacitor Ceramic .1uf 50V Axial Lead R27 | 11-00001-103 | Resistor 10K %W +5% 12-10002-104 | Capacitor Ceramic .1uf 50V Axial Lead R28 | 11-00001-223 | Resistor 22K 4%W +5% 12-10002-104 | Capacitor Ceramic .1uf 50V Axial Lead R29 | 11-00001-562 | Resistor 5.6K %4W +5% 12-10002-104 | Capacitor Ceramic .1uf 50V Axial Lead R30 11-00001-332 Resistor 3.3K YaW +5% 12-10002-104 Capacitor Ceramic .1uf 50V Axial Lead

R31 11-00001-020 Resistor 2.2 OHM %4W +5% 12-10002-104 Capacitor Ceramic .1uf SOV Axial Lead R32 11-00001-010 Resistor 1 OHM %2W +5% 12-10002-104 Capacitor Ceramic .1uf 50V Axial Lead R33 11-00001-020 Resistor 2.2 OHM %W +5% 12-10003-470 Capacitor 47pf 10% NPO Axial Lead R34 11-00001-010 Resistor 1 OHM ¥eW +5% 12-20001-105 Capacitor Electrolytic 1uf R35 11-00001-102 Resistor 1.0K OHM %W +5% 12-10002-104 Capacitor Ceramic .1uf 50V Axial Lead R36 11-00001-332 Resistor 3.3K %W +5% 12-20001-807 Capacitor Electrolytic 800uf, 16V R37 11-00001-152 Resistor 1.5K %4W +5% C23 12-20001-807 Capacitor Electrolytic 800uf, 16V R38 | 11-00001-222 | Resistor 2.2K YW +5% C24 | 12-10001-471 | Capacitor Ceramic 470pf 50V 10% Axial Lead R39 | 11-00001-221 | Resistor 220 OHM %4W +5% C25 | 12-10001-471 | Capacitor Ceramic 470pf 50V 10% Axial Lead R40 | 11-00001-332 | Resistor 3.3K YW +5% C26 | 12-10001-471 | Capacitor Ceramic 470pf SOV 10% Axial Lead| R41 | 11-00001-562 | Resistor 5.6K %W +5% C27 | 12-10001-471 | Capacitor Ceramic 470pf 50V 10% Axial Lead R42 | 11-00001-223 | Resistor 22K %4W +5% C28 | 12-10001-471 | Capacitor Ceramic 470pf 50V 10% Axial Lead R43. | 11-00001-103 | Resistor 10K %W +5% C30 | 12-10001-471 | Capacitor Ceramic 470pf 50V 10% Axial Lead

R44 | 11-00001-103 | Resistor 10K %4W +5%C31}12-10001-471 | Capacitor Ceramic 470pf 50V 10% Axial Lead

R45 | 11-00001-103 | Resistor 10K %W +5% C32 | 12-10001-471 | Capacitor Ceramic 470pf 50V 10% Axial Lead R50 | 11-00001-472 | Resistor 4.7K vaW +5% C33 | 12-10002-104 | Capacitor Ceramic .1uf 50V Axial Lead FB1 | 17-00001-001 | Ferrite Bead C34 | 12-10002-104 | Capacitor Ceramic .1uf 50V Axial Lead FB2 | 17-00001-001 | Ferrite Bead C35 | 12-10002-104 | Capacitor Ceramic .1uf 50V Axial Lead FB3 | 17-00001-001 | Ferrite Bead C36 | 12-10002-104 | Capacitor Ceramic .1uf SOV Axial Lead FB4 | 17-00001-001 | Ferrite Bead

Page 46

DATA/SOUND PROCESSOR

TAITO PART NO. DESCRIPTION PART NO. DESCRIPTION

12-10002-104 12-10002-104 -luf SOV Axial Lead -luf 50V Axial Lead Capacitor Ceramic Capacitor Ceramic SYM TP3 59-00021-001 Test Point 59-00021-001 Test Point

12-10001-123 Capacitor Ceramic .012 50V Axial Lead 12-10001-183 Capacitor Ceramic .018 50V Axial Lead 12-10004-103 Capacitor Ceramic .O1uf SOV Axial Lead TP4 TP5 59-00021-001 Test Point 59-00021-001 Test Point

TP7 §9-00021-001 Test Point

12-10001-332 Capacitor Ceramic .0033uf SOV Axial Lead TP8 59-00021-001 Test Point C43 | 12-10001-153 | Capacitor Ceramic .015uf 50V Axial Lead TPQ | 59-00021-001 | Test Point C44 | 12-10001-563 | Capacitor Ceramic .056uf 50V Axial Lead TP10 | 59-00021-001 | Test Point C45_ | 12-10003-100 | Capacitor 10pf NPO Axial Lead TP11 | 59-00021-001 | Test Point C46 | 12-10002-104 | Capacitor Ceramic .1uf 50V Axial Lead RP1 | 11-50001-332 | Resistor Sip Pack 3.3K C47 | 12-20001-105 | Capacitor Electrolytic 1uf Axial Lead RP2 | 11-50001-332 | Resistor Sip Pack 3.3K C48 | 12-20001-105 | Capacitor Electrolytic 1uf Axial Lead RP3 | 11-50001-471 | Resistor Sip Pack 47K C49 | 12-10001-471 | Capacitor Ceramic 470uf SOV Axial Lead RP4 | 11-50001-471 | Resistor Sip Pack 47K C50 | 12-10001-471 | Capacitor Ceramic 470pf 50V Axial Lead RP5 | 11-50001-103 | Resistor Sip Pack 10K C51 | 12-10002-104 | Capacitor Ceramic .1uf 50V Axial Lead RP6 | 11-50001-332 | Resistor Sip Pack 3.3K C52 | 12-10002-104 | Capacitor Ceramic .1uf 50V Axial Lead U1 | 15-20244-001 | Octal Buffer (74LS244) C53_| 12-10002-104 | Capacitor Ceramic .1uf 50V Axial Lead U2 | 15-00002-001 | Microprocessor 68AOSE | C54 | 12-10002-104 | Capacitor Ceramic .1uf SOV Axial Lead 26-00001-040 | Socket 40P DIP-For 68AO9E C55 | 12-20001-105 | Capacitor Electrolytic tuf U3 | 15-20244-001 | Octal Buffer (7415244) C56 | 12-10002-104 | Capacitor Ceramic .1uf 50V Axial Lead U4 | 15-20244-001 | Octal Buffer (74LS244) C57 | 12-20001-477 | Capacitor Electrolytic 470uf, 16V U5 | 15-00007-001 | Microprocessor 6802 12-20001-477 | Capacitor Electrolytic 470uf, 16V 26-00001-040 | Socket 40P DIP for 6802 12-10002-104 | Capacitor Ceramic .1uf 50V Axial Lead 15-20244-001 | Octal Buffer (74LS244) 12-10002-104 Capacitor Ceramic .tuf 50V Axial Lead 15-00004-002 Parallel 1/0 6821

12-10001-471 Capacitor Ceramic 470pf 50V 10% Axial Lead 15-00004-002 Parallel 1/0 6821

12-10001-471 Capacitor Ceramic 470pf SOV 10% Axial Lead 15-20245-001 BUS Tranciever, Octal (74LS245)

12-10001-471 Capacitor Ceramic 470pf 50V 10% Axial Lead] 15-20244-001 Octal Buffer (74LS244) 12-10001-471 Capacitor Ceramic 470pf 50V 10% Axial Lead 15-20245-001 BUS Tranciever, Octal (74LS245)

12-10001-471 Capacitor Ceramic 470pf 50V 10% Axial Lead 15-20244-001 Octal Buffer (74LS244)

12-10001-471 Capacitor Ceramic 470pf 50V 10% Axial Lead 15-50001-001 Digital to Analog Converter 8 Sit (1408)

12-10001-471 Capacitor Ceramic 470pf SOV 10% Axial Lead 15-20032-001 Quad 2-Input or (74LS32)

12-10002-104 Capacitor Ceramic .1uf 50V Axial Lead 15-10003-001 RAM 1K x 4 NMOS Static (2114)

12-10002-104 Capacitor Ceramic .1uf 50V Axial Lead 26-00001-018 Socket 18P DIP for 2114

12-10002-104 Capacitor Ceramic .1uf 50V Axial Lead 15-10003-001 RAM 1K x 4 NMOS Static (2114)

12-10002-104 Capacitor Ceramic .1uf 50V Axial Lead 26-00001-018 Socket 18P DIP for 2114

12-10003-101 Capacitor 100pf 10% NPO Axial Lead | 15-20738-001 Decoder 1 of 8 (74LS138)

12-10003-221 Capacitor 220pf 10% NPO Axial Lead 15-50003-001 Quad OP AMP LM324 12-10002-104 | Capacitor Ceramic . uf 50V Axial Lead 15-60004-001 | Speech Synthesis TMS5200 12-20001-105 | Capacitor Electrolytic 1uf 26-00001-028 | Socket 28P DIP for TMS5200 12-20001-105 | Capacitor Electrolytic tuf U20 | 15-00004-001 | Parallel 1/0 68A21 12-10002-104 | Capacitor Ceramic .1uf 50V Axial Lead U21 | 15-60002-001 | Line Driver (MC1488) 12-10002-104 | Capacitor Ceramic .1uf 50V Axial Lead U22 | 15-00005-002 | Serial 1/0 68A50 Capacitor Ceramic .1uf 50V Axial Lead 26-00001-024 | Socket 24P DIP for 68A50 Capacitor Ceramic 470pf 50V 10% Axial Lead 23 | 15-20004-001 | Inverter, HEX (74LS04) Capacitor Ceramic 470pf 50V 10% Axial Lead U24 | 15-44066-001 | Quad Analog Multiplexer (4066) Capacitor 10pf NPO Axial Lead U25 | 15-60001-001 | Line Receiver (MC1489) 59-00021-001 | Test Point U26 | 15-20161-001 | Counter 4-Bit Presettable (74LS161) Test Point 27 | 15-20092-001 | Counter Divide By Twelve (74LS92) U28 | 15-44066-001 | Quad Analog Multiplexer (4066)

Page 47

DATA/SOUND PROCESSOR

SYM TAITO PART NO. DESCRIPTION s 15-50002-001 | Audio Amplifier (2002) 30-00001-001 | Heatsink to 220 15-50002-001 | Audio Amplifier (2002) 30-00001-001 | Heatsink to 220 SW1 | 29-00001-001 | Switch, DIP 4 Pole Yt 19-00002-001 | Crystal 7.3728 MHZ Q1__| 14-23904-001 | Transistor NPN, Silcon 2N3904 Jt | 25-00002-004 | Connector 14 PIN Locking J5 | 25-00001-001 | Connector Header 50 PIN J6 | 25-00001-001 | Connector Header 50 PIN J7 | 25-00002-005 | Connector 5 PIN Locking | J8 | 25-00002-005 | Connector 5 PIN Locking JQ | 25-00003-001 | Connector RS232

Page 48

w 8 BBRBRBEEE ROM/V/0 P.C. ASSEMBLY COMPONENT LAYOUT

; || sree

SE] §

tana” *en [es]

C3) itr23) a

iC 23)

GD ¥s

CED) ¥ 91 100-€0000-80 ‘WSN NI JOVW ftsxa]

GED ¥en 2n *In

  • 66

: a Q |e fo.

Fon

ch efle] slalela ais ele eee pHs 068 ggg hETEAGe BRee (| HG GSSEERREE ER SEERBRABES LJ —— Co [ts 3] I “8 GBGE BERBBRSS * BE BERGER BBE *

Page 49

ROM/1/0 P.C. ASSEMBLY

Tato TAITO

SYM | PART NO.DESCRIPTIONSYM | PART NO.DESCRIPTION

Ri | 11-00001-562 | Resistor 5.6K, 4W/+5% R51 | 11-00001-471 | Resistor 470 OHM YW +5%

R2_|11-00001-471 | Resistor 470 OHM YW +5%R52 | 11-00001-562 [Resistor 5.6K, YW +5%
R3__|11-00001-471 | Resistor 470 OHM %W +5%R53 | 11-00001-562 | Resistor 5.6K, 4W +5%

R4 | 11-00001-471 | Resistor 470 OHM YW +5% R54 | 11-00001-471 | Resistor 470 OHM %4W +5% R5 | 11-00001-471 | Resistor 470 OHM YW +5% R55 | 11-00001-471 | Resistor 470 OHM %4W +5% R6 | 11-00001-471 | Resistor 470 OHM YAW =5% R56 1 11-00001-471 | Resistor 470 OHM YW =5% R7 | 11-00001-471 | Resistor 470 OHM YW +5% R57 | 11-00001-471 | Resistor 470 OHM “W +5% R8 | 11-00001-471 | Resistor 470 OHM YW +5% R58 | 11-00001-471 | Resistor 470 OHM YW +5% RQ | 11-00001-471 | Resistor 470 OHM YW +5% R59 | 11-00001-471 | Resistor 470 OHM %4W +5% R10 | 11-00001-471 | Resistor 470 OHM Y4W +5% R60 | 11-00001-471 | Resistor 470 OHM %4W +5% Rit | 11-00001-471 | Resistor 470 OHM YW +5% R61 | 11-00001-471 | Resistor 470 OHM %W +5% R12 | 11-00001-471 | Resistor 470 OHM YW +5% R62 | 11-00001-471 | Resistor 470 OHM %W +5% R13 | 11-00001-471 | Resistor 470 OHM %4W +5% R63 | 11-00001-471 | Resistor 470 OHM %4W +:5% R14 | 11-00001-471 | Resistor 470 OHM YW +5% C1 | 12-10002-104 | Capacitor Ceramic .1uf Axial Lead

R15 | 11-00001-471 | Resistor 470 OHM YaW +5%~|C2__|12-10002-104 | Capacitor Ceramic .1uf Axial Lead
R16 | 11-00001-471 | Resistor 470 OHM YaW +5%C312-10001-471|Capacitor Ceramic 470pf Axial Lead
R17 | 11-00001-471 | Resistor 470 OHM %W +5%C412-10001-471 | Capacitor Ceramic 470pf Axial Lead
R18 | 11-00001-471 | Resistor 470 OHM YaW +5%C512-10001-471 | Capacitor Ceramic 470pf Axial Lead

RiS | 11-00001-471 | Resistor 470 OHM YW +5% C6 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead R20 | 11-00001-562 | Resistor 5.6K, 4W +5% C7 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead R21 | 11-00001-562 | Resistor 5.6K, %4W +5% C8 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead R22 | 11-00001-562 | Resistor 5.6K. %W +5% C9 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead R23 | 11-00001-562 | Resistor 5.6K, 4W +5% C10 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead R24 | 11-00001-562 | Resistor 5.6K, %4W +5% C11 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead R25 | 11-00001-562 | Resistor 5.6K, %W +5% C12 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead R26 | 11-00001-562 | Resistor 5.6K, %4W +5% NY C13 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead R27 | 11-00001-562 | Resistor 5.6K, %4W +5% C15 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead

R28 | 11-00001-471 | Resistor 470 OHM YW +5%C16 | 12-10001-471|Rapacitor Ceramic 470pf Axial Lead

R29 | 11-00001-471 | Resistor 470 OHM %W +5% C17 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead R30 | 11-00001-471 | Resistor 470 OHM YW +5% C18 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead R31 | 11-00001-471 | Resistor 470 OHM %4W +5% | C19 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead R32 | 11-00001-471 | Resistor 470 OHM YW +5% C20 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead

R33!11-00001-471 | Resistor 470 OHM “W +5%C21 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead

R34 | 11-00001-471 | Resistor 470 OHM %4W +5% C22 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead R35 | 11-00001-471 | Resistor 470 OHM YW +5% C23 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead R36 | 11-00001-471 | Resistor 470 OHM YaW +5% C24 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead R37 | 11-00001-471 | Resistor 470 OHM YW +5% C25 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead R38 | 11-00001-471 | Resistor 470 OHM %4W +5% C26 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead R39 | 11-00001-471 | Resistor 470 OHM YW +5% C27 | 12-10002-104 | Capacitor Ceramic .1uf Axial Lead R40 | 11-00001-562 | Resistor 5.6K, 4W +5% C28 | 12-10002-104 | Capacitor Ceramic .1uf Axial Lead R41 | 11-00001-562 | Resistor 5.6K, 4W +5% C29 | 12-10002-104 _| Capacitor Ceramic . tuf Axial Lead

R42 | 11-00001-562 | Resistor 5.6K, %&W +5%C30 | 12-10002-104{Capacitor Ceramic .tuf Axial Lead

R43 | 11-00001-562 | Resistor 5.6K, YaW +5% C31 | 12-10002-104 | Capacitor Ceramic .tuf Axial Lead R44 | 11-00001-471 | Resistor 470 OHM %4W +5% C32 | 12-10002-104 | Capacitor Ceramic .1uf Axial Lead R45 | 11-00001-471 | Resistor 470 OHM %4W +5% C33 | 12-10002-104 | Capacitor Ceramic .tuf Axial Lead R46 | 11-00001-471 | Resistor 470 OHM Y4W +5% C34 | 12-10002-104 | Capacitor Ceramic .1uf Axial Lead R47 | 11-00001-471 | Resistor 470 OHM YW +5% C35 _| 12-10002-104 | Capacitor Ceramic .1uf Axial Lead R49 | 11-00001-471 [Resistor 470 OHM %4W +5% C36 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead R50 11-00001-471 Resistor 470 OHM V4W +5%

Page 50

ROM/V/0 P.C. ASSEMBLY

TAITO PART NO. DESCRIPTION 42-10001-471 |Capacitor Ceramic 470pf Axial Lead 12-10001-471 |Capacitor Ceramic 470pf Axial Lead 12-10001-471 |Capacitor Ceramic 470pf Axial Lead 12-10001-471 |Capacitor Ceramic 470pf Axial Lead 12-10001-471 |Capacitor Ceramic 470pf Axial Lead DESCRIPTION C37 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead 12-10001-471 | Capacitor Ceramic 470pf Axial Lead C39 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead C40 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead C41 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead C42 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead 12-10001-471 | Capacitor Ceramic 470pf Axial Lead

C43 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead12-10001-471|Capacitor Ceramic 470pf Axial Lead
C44 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead12-10001-471|Capacitor Ceramic 470pf Axial Lead

| C45 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead 17-00001-001 | Ferrite Bead

C46 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead17-00001-001|Ferrite Bead

| C47 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead 17-00001-001 | Ferrite Bead C48 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead 17-00001-001 | Ferrite Bead C49 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead 17-00001-001 | Ferrite Bead C50 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead 17-00001-001 | Ferrite Bead C51 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead 17-00001-001 | Ferrite Bead C52 | 12-10002-104 | Capacitor Ceramic .1uf Axial Lead FB8 | 17-00001-001 | Ferrite Bead C53 | 12-10002-104 | Capacitor Ceramic .1uf Axial Lead FB9 | 17-00001-001 | Ferrite Bead C54 | 12-10002-104 | Capacitor Ceramic .1uf Axial Lead FB10 | 17-00001-001 | Ferrite Bead C55 | 12-10002-104 | Capacitor Ceramic .1uf Axial Lead FB11 | 17-00001-001 | Ferrite Bead 12-10002-104 | Capacitor Ceramic .1uf Axial Lead FB12 | 17-00001-001 | Ferrite Bead 12-10002-104 | Capacitor Ceramic .1uf Axial Lead FB13 | 17-00001-001 | Ferrite Bead 12-10002-104 | Capacitor Ceramic .1uf Axial Lead FB14 | 17-00001-001 | Ferrite Bead C59 | 12-10002-104 | Capacitor Ceramic .1uf Axial Lead FB15 | 17-00001-001 | Ferrite Bead C60 | 12-10002-104 | Capacitor Ceramic .1uf Axial Lead FB16 | 17-00001-001 | Ferrite Bead C61 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead FB17 | 17-00001-001 | Ferrite Bead C62 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead FB18 | 17-00001-001 | Ferrite Bead C63 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead FB19 | 17-00001-001 | Ferrite Bead 64 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead FB20 | 17-00001-001 | Ferrite Bead C65 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead FB21 | 17-00001-001 | Ferrite Bead C66 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead FB23 | 17-00001-001 | Ferrite Bead C67 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead FB24 | 17-00001-001 | Ferrite Bead C68 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead FB25 | 17-00001-001 | Ferrite Bead C69 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead FB26 | 17-00001-001 | Ferrite Bead C70 | 12-20001-107 | Capacitor Electrolytic 100uf F827, | 17-00001-001 | Ferrite Bead C71 | 12-10001-471 | Capicitor Ceramic 470pf Axial Lead FB28 | 17-00001-001 | Ferrite Bead C72 | 12-10002-104 | Capacitor Ceramic .1uf Axial Lead FB29 | 17-00001-001 | Ferrite Bead C73 | 12-10002-104 | Capacitor Ceramic .1uf Axial Lead FB30 | 17-00001-001 | Ferrite Bead C74 | 12-10002-104 | Capacitor Ceramic .1uf Axial Lead FB31 | 17-00001-001 | Ferrite Bead C75 | 12-10002-104 | Capacitor Ceramic .1uf Axial Lead FB32 | 17-00001-001 | Ferrite Bead C76 | 12-10002-104 | Capacitor Ceramic .1uf Axial Lead FB33 | 17-00001-001 | Ferrite Bead C77 | 12-10002-104 | Capacitor Ceramic .1uf Axial Lead FB34 | 17-00001-001 | Ferrite Bead C78 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead | FB35 | 17-00001-001 | Ferrite Bead C79 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead FB36 | 17-00001-001 | Ferrite Bead C80 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead FB37 | 17-00001-001 | Ferrite Bead C81 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead FB38 | 17-00001-001 | Ferrite Bead C82 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead FB39 | 17-00001-001 | Ferrite Bead C83 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead FB40 | 17-00001-001 | Ferrite Bead C84 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead FB41 | 17-00001-001 [Ferrite Bead

Page 51

ROM/V/0 P.C. ASSEMBLY

TAITO{—_]raito
‘SYM | PART NO.DESCRIPTIONSYM | PART NO.DESCRIPTION
FB42 | 17-00001-001 | Ferrite BeadU6Not Used

FB43 | 17-00001-001 | Ferrite Bead 26-00001-024 | Socket 24 Pin Dip for U6

F844 | 17-00001-001 | Ferrite BeadU7Not Used

FB45 | 17-00001-001 | Ferrite Bead 26-00001-024 | Socket 24 Pin Dip for U7

FB46 | 17-00001-001 | Ferrite BeadusNot Used

fear} 17-00001-001 | Ferrite Bead 26-00001-024 | Socket 24 Pin Dip for U8 FB48 | 17-00001-001 | Ferrite Bead ug _| Not Used FB49 | 17-00001-001 | Ferrite Bead 26-00001-024 | Socket 24 Pin Dip for U9

FB50 | 17-00001-001 | Ferrite BeadU10Not Used

FB51 | 17-00001-001 | Ferrite Bead 26-00001-024 | Socket 24 Pin Dip for U10 FB52 | 17-00001-001 | Ferrite Bead U11_|15-00004-001 | Paralell 1/0 68A21

FB53 | 17-00001-001 | Ferrite Beadu12E-PROM “‘ZOOKEEPER''™

D1 | 13-14001-001 | Diode IN4001 26-00001-024 | Socket 24 Pin Dip for U12

D2 | 13-14001-001 | Diode IN4001U13Not Used

D3 | 13-14001-001 | Diode IN4001 26-00001-024 | Socket 24 Pin Dip for U13

D4 | 13-14001-001 | Diode IN4001U14E-PROM “‘ZOOKEEPER''™

D5 | 13-14001-001 | Diode IN4001 26-00001-024 | Socket 24 Pin Dip for U14

D6 | 13-14001-001 | Diode IN4001U15E-PROM ‘‘ZOOKEEPER’'™

D7 | 13-14001-001 | Diode IN4001 26-00001-024 | Socket 24P Dip Used ForE-PROM

D8 | 13-14001-001 | Diode IN4001U16E-PROM “'ZOOKEEPER’™

D9 | 13-14001-001 | Diode IN4001 26-00001-024 | Socket 24 Pin Dip for U16

D10 | 13-14001-001 | Diode IN4001U17E-PROM “‘ZOOKEEPER''™

D11_ | 13-14001-001 | Diode IN4001 26-00001-024 | Socket 24 Pin Dip for U17

D12 | 13-14001-001 | Diode IN4001U18E-PROM “‘ZOOKEEPER"™

Q1 | 14-00001-001 | Transistor NPN DarlingtonTIP120 26-00001-024 | Socket 24 Pin Dip for U18

Q2 | 14-00001-001 | Transistor NPN DarlingtonTIP120U19E-PROM “‘ZOOKEEPER'’™

Q3 | 14-00001-001 | Transistor NPN DarlingtonTIP120 26-00001-024 | Socket 24 Pin Dip for U19 Q4 | 14-00001-001 | Transistor NPN DarlingtonTIP120 U20 | 15-00004-001 | Paralell 1/0 68A21 Q5 | 14-00001-001 | Transistor NPN DarlingtonTIP120 U21 | 15-20138-001 | Decoder 1 of 8 (138)

Q6 | 14-00001-001 | Transistor NPN DarlingtonTIP120U22|26-00002-032 | ROM Select

Q7 | 14-00001-001 | Transistor NPN DarlingtonTIP120 26-00001-014 | Socket 24P Dip for U22 Q8 | 14-00001-001 | Transistor NPN DarlingtonTIP120 U23 | 15-20004-001 | Inverter, HEX (74LS04)

agNot UsedU24Not Used
Q10 | 14-00001-001 | Transistor NPN DarlingtonTIP120U25E-PROM ‘ZOOKEEPER''™
Q11 | 14-00001-001[Transistor NPN DarlingtonTIP120U26E-PROM “‘ZOOKEEPER’'™
Q12|14-00001-001 | Transistor NPN DarlingtonTIP120U27E-PROM ‘‘ZOOKEEPER’'™
U1Not Used26-00001-014 | Socket 24P Dip for U27

26-00001-014 | Socket 14P Dip, for U1 U28 | 15-20138-001 | Decoder 1 of 8 (138) U2 | 15-20138-001 | Decoder 1 of 8 (138) U29 | 26-00002-032 | ROM Select

U3Not Used26-00001-014 | Socket 14P Dip Used For ROMSelect

26-00001-024 | Socket 24 Pin Dip for U3 U30_ | 15-00004-001 | Paralell 1/0 6821

U4Not UsedJ3___|25-00001-001 | Connector Header 50PIN
26-00001-024 | Socket 24 Pin Dip for U4J525-00001-001 | Connector Header SOPIN
U5Not UsedJ6_|25-00001-001 | Connector Header SOPIN
26-00001-024 | Socket 24 Pin Dip for USJ11|25-00002-014 | Connector 14 Pin Header .156Center

J15 _}25-00002-014 | Connector 14 Pin Header .156Center J16 _|25-00002-014 | Connector 14 Pin Header .156Center J17 |25-00002-014 | Connector 14 Pin Header .156Center

Page 52

VIDEO ROM EXPANSION BOARD

TAITO ITEM PART NO. DESCRIPTION 1 32-00220-001 | 6809 Video ROM P.C.B. 25-00001-001| Conn Header Vert, 50 pin 25-00002-014| Conn 14 Pin Locking 26-00001-024} Socket Dip 24 Pin 17-00001-001 | Ferrite Bead

15-20138-001| Decoder 1 of 8 74LS138 15-20074-001| Flip Flop Dual D 74LS74 6 12-20001-107| Cap Elect 16V 100uf

15-20157-001| Miti Quad 2 Input 74LS157 10 15-20000-001 | Quad 2 Input Nand 74LS00 1 11-00001-332 | Resistor 3300 ohm %4W 5% 12 12-10001-471 | Cap 470PF 50V 10% X7R AXL 13 12-10002-104| Cap Cer .1uf 50V

Page 53

VIDEO ROM EXPANSION BOARD

Page 54

XXX Bee lo} Jo} Jo} Jo} JO} Jo} jo ca] |c0} |co} SES EDSES co} oo} Joo} Joo} Jo Poaceae arene 3 BEE d S| 10} S| LS] LS 100-O01000-SI Q 7 +

OxXXKXKXXXXXX) x) cold Lj x XK XXX KX) ix KXXXXXX XXX XK el 3unold ANOAVT GUYOd HOSSII0Ud NIOD

Page 55

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 56

WIRING DIAGRAM

qf ==}

OM VIDED PROCESSOR ES PCB

PRIM AR BRACKET anime

Page 57

POWER SUPPLY BOARD SCHEMATIC

FIGURE 16 NOTICE TO ALL PERBONG RECEIVING THs ORAWING Courioen tin. Reprodcie ister thou RET A claps he ne ek

facture une the eo Tegroduce tm drawing w granted. othe rect omit by winton agreement wi oF REVISIONS

SECONDARY BRACKET

GE) PF F

za | loo[aszPG ono
220K100K$+—_C3end

PT vee RE TRICT ame ec

sséu2a os|RSCJa-5 eno

meour VOLTAGE PROGRAMMING JUMPER

GND _Veows Veong OUTarkGND

co ay Tes P E 7 224F | oF ‘Ol J4=7 GND

Be 4683a=) HRST

22k ‘S08 Ja-14_) RST wee $C ono = L__Caei Jono Fe be J2-( Soe Jo-2 )BASE Ri 152 aw

RS—Ja-3_)eM
ING276ATKJ2-4=

RIO, Ro i5.a aw

ce Vf RIZ

+i\yJs) +58
22KRis CURRENT4Aass *5

FOLD BACK JRIS

21tytigreaaL_ Gare )+s
Rae =FineserCis)28
24|*{Gaz :28
IINTERLOCKJ2-5ee
aaBROWN+t5J2-G BASE

; 2N3055 + R33 $5 OK om N INe2si R22 Je-7 oe R23 a | eux-wirt

4! euk-rep:

Ny p----) -=-----

2N3055 ~ 5, Lo dprcuaen FOR 120V LINE (

1 4 on/orr V275LAISA FOR 240VLINE | ff rT ansosst_{ ansoss

{ !

\ I

R32 De )+eA tL. ----_4 a4w ror Pe INSG4B HEAT SINK ASSY

CISR30D7Qa(J4-G + 12A

2K ‘Laneaoi TAF y rata CG3=10_)12¢ FLED 2 GF )+2€ eK ° VOLTAGE 8) “12 ADJUST + J4-8 )-12 R34

pe12kps4 5

OAT EA ao

LED 4 vey.C 9359 2ITSLOEAS ory 1 27g +E tony i 22FH Le 2.2uF F y

TAITO AMERIGA CORPORATION

POWER SUPPLY ASSEMBLY

Page 58

VIDEO PROCESSOR BOARD SCHEMATIC 1 OF 2

VAIO 1) 12 (3 1415,

+5Vg grey "ou ~ 3.6V pe 32. pSRH_24 U8 Me

4lle|8

a =

xttTrronle
=<aEaM
aBleyn
E1013Ul yasJADR=BB0OHT!caer
i24CeeD
le-oe

rede luis see

egT2,51Oy134138=

68A45. -

iccMaiuf

| ha = uso] uls eS 2, S/1Q3 JADR REC eee aad form aes scot 28, tBY +5 33K 86 Ss inv. U5t &

ADR= 8COOH

_POWER/ GROUND. Pia

  • NOTICE TO ALL PERSONS RECEIVING THIS DRAWING 20M ei CONFIDENTIAL = Reproduction forbidden without

22k R? ~ Re 220

c3l 100 PF:

Ss es bal = a VIDEO PROCESSOR Perey Tel s2-6600 [4

Page 59

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 60

DATA/SOUND PROCESSOR BOARD SCHEMATIC

Ceitese~ ~~ 7 oa 1 (1O)PLACES, I 1° Lona aed

83 _C5= 8S get Cenas ea + fiery Ges ; : . (35-37) « ca? 70 vy IME

i Bag “i = SOUND FODREZS BUS SCINTCOMS SOUNT BATS BUS a.

DER See Be: Toe COR SE

pce B-DPR

Kt 2 35 1° 3H ow RET 2,E

NOTICE TO ALL PERSONS RECEIVING THiS DRAWING.

Specttic wektan vor Grove Vitageit.° Theo

Page 61

ROM/I/0 BOARD SCHEMATIC

av “sv DATA PROGRAM ry

T/0 CKT'S11)7
3UI} ul? ut5| Ul,i¥=
8luis) Jui ula) ula pnywe iemaEs
a—>
ig-l|-l-/-]/el-t#sitlopeD4
sf 8zlzlzlalzlel2i zieElE/El2 ] ep, 22
=araaaaPatani lB a?
a4inEIEVEIS/ETE & |S podfran ti aD:
a,i)eye eyerey?Stett/zlz boLo
5| avanPeesCor
a9g/alalslelgjs/apt.18/8 {aa)
*BI8/88 /Si8 s/s 17618|StaSan he tt | 5
74aB/ 2] B/S) 8] S/S] Ss hz dose!Ele/8+l 3PLACES

59 {

A3we yey ype ye pepe ye +eyene +
38 PLACES}IPS,
a3Ppsunt2 (50)

MEO ("al )}

7 ONE PLAYER 3 L t

a16]FERRITE BEADS (5)
¢-5
€142
|U0)usCn ean poeOOco SBRRE ry EBSS,
zrev9] ] u7|?°lus|“Juslis [vos Aa)eterna
--—-#ad)zislzleleieisleos

EVE|E EEE ele x EVER EEE ElE

A=E/E/E/E/S/S 15/5

| cl/z/zix[zix{zlz A S/S 5/51 S/S) 5/5

348181818) 2/8/813
e3Ele S/Sisleisis

2 i" 18 718 716 VIS T me | i

iJPL.

2 ‘oie _) Seo py 8 U6 Ra 20 _) |

&VIDEO PROGRAMo

(a Cc

A PUWER/GROUND TABLE

a(68420 | 66a21 MEMORY MAPadcxctss [ria] |
aTC NOV PORT & [CONTROYPORTE] CORTErimt0
ADIR REG REG A_| DIREG B271642 124 {
Ault | 9400H] 9401] 9402] 9403Hreera-
Au20 | 9900 | 9901 H] 9902H]| 92031S

uso | 9co0H] acor | acozH| gco3H

Li} us Li2|

NOTICE TO ALL PEREONS RECEWING THIS DRAWING 1d natner racetet mor bonuse ae

fieneproduce ts arawig w grantac. or thean
writen pomiolon tom the corporation-ROM/IO.

igesy~" [eTszscteos ry

Page 62

VIDEO ROM EXPANSION BOARD SCHEMATIC

N vv 24 PIN SOCKETS

aq > 7 ai) g—vall

A, +5v slur 8 PLACES (Al rr. pat

N @

w EE w an foo

N my [I iS ro 741500 vio | v4 ue u7 | v6 us | Ut | U3

y BN) KS

J3 silplis este + Wn d o ® @ Cy a a ry a

24+ = 8

a, J3

35 a 36 q =

PU. NOTICE TO ALL PERSONS RECEIVING THIS ORAWING

UAL 6809 SYSTEM VIDEO_ROM EXPANSION Seay Te Gr soza-oo |

Page 63

WARRANTY

TAITO AMERICA CORPORATION warrants that its printed circuit boards and parts are free from defects in material and workmanship under nomal use and service for a period of ninety (90) days from the date of shipment. Seller warrants that its monitors are free from defects in material and workmanship under normal use for a period of thirty (30) days from the date of shipment. The factory also warrants all socketed parts for a period of ninety (90) days when furnished with the game serial number. If the above products fail to conform to this Warranty Taito America Corporation has the option to repair, replace, or credit the Buyer’s account. The Buyer must notify Taito America Corporation in writing upon finding the defective product. Buyer must also return the defective product prepaid to Taito America Corporation’s factory located in Elk Grove Village, Illinois. If Taito America Corporation determines upon examining the returned product that damage was caused by accident, misuse, neglect, modification, or improper repair or testing, this Warranty will be void. Inno event will Taito America Corporation be held for loss of profits to Buyer.

Page 64

® TAITO AMERICA CORPORATION 1256 Estes Avenue, Elk Grove Village, IL 60007 Telephone (312) 981-1000 Telex 25-3290