CATHODE RAY TOMES

Data East DX-1 Multi Conversion Kit Installation Instructions

DX-1 Multi Conversion Kit (Data East USA, Inc.) · Installation · 45 pages · 11 sections · original scan

Page 1

DX-1 MULTI CONVERSION KIT

VIDEO GAME SYSTEM

INSTALLATION INSTRUCTIONS

Page 2

F.C.C. COMPLIANCE

TRE DATA EAST MULTI CONVERSION SYSTEM Dx-1 UTILIZES ELECTRONIC SIGNALS THAT COULD CAUSE INTERFERENCE TO RADIO AND TV RECEPTION IF IT IS NOT PROFERLY INSTALLED.

IF THE INSTALLER OF THIS SYSTEM DEVIATES FROM THE INSTRUCTIONS CONTAINED HEREIN, THERE MAY BE INTERFERENCE CREATED IN VIOLATION OF F.C.C CLASS A STANDARDS.

HIGH VOLTAGE

ALL VIDEO GAMES THAT MAY BE CONVERTED TO THE DATA EAST MULTI CONVERSION SYSTEM USE LIFE THREATENING HIGH VOLTAGES. ONLY QUALIFIED ELECTRONIC PERSONNEL SHOULD PERFORM THESE CONVERSIONS.

Page 3

14,

16.

17.

19.

22. Table of Contents

STEP BY STEP SUMMARY

INTRODUCTION

  • General Description
  • Choosing The Machine To Be Converted

GETTING STARTED

  • Review
  • Card Rack Installation
  • Power Supply Options
  • Power Supply Installation

APPLYING POWER

  • Connecting The Speaker
  • Quick Sound And System Test
  • Connecting The Video Monitor

INSTALLING THE TAPE DECK ASSEMBLY

Tape Deck Connection

INSTALLING THE GAME KIT

  • Dip Switches
  • Inserting The Tape
  • Connecting The Key Module

COSMETIC CONVERSION

TROUBLESHOOTING GUIDE

REFERENCE DATA

  • Electrical Specifications
  • Mechanical Specifications
  • Cable Section Schematics And Parts Lists

CHANGING A GAME IS EASY

Page 4

STEP BY STEP SUMMARY

  • REMOVE ALL OLD GRAPHICS. 2. INSTALL CARD CAGE & POWER SUPPLY.

or

  • INSTALL TAPE DECK AND TEST 4. APPLY OVERLAY TO CONTROL PANEL
Page 5

STEP BY STEP SUMMARY

  • REPAINT AND 6a INSTALL GAME KIT

OR APPLY NEW GRAPHICS

6b. INSTALL GAME KIT T. ADMIRE CONVERTED GAME

Page 6

INTRODUCTION

GENERAL DESCRIPTION

The Data East MULTI CONVERSION Dx-1 is a video game reprogrammable conversion system that can extend the usable life of old game cabinets.

The DX-1 System is designed to accept the game kits offered for use in the DECO CASSETTE INTERCHANGEABLE GAME SYSTEMS 113, 1174, 1732, 1U2, 1U3, 1U4, NDB-4x, & 1US5 which have been offered in the United States since 1980.

As the DECO CASSETTE SYSTEM is so flexible and able to accept games designed for a wide variety of controls which were not included in many of our old game cabinets; our customers must accept the responsibility of control panel and graphics modifications depending upon the game kits ordered.

The DX-1 MULTI CONVERSION SYSTEM consists of a Card Cage, three Circuit Boards, a Tape Deck Assembly, Interconnection Cables, and Cosmetic Graphics. Optional power supplies are available and recommended by Data East for most applications.

The card cage (with the three Printed Circuit Boards, Cable V-200238-0 and Cable V-200239-0 installed) is packaged in a specially molded styrofoam box for maximum protection. (See Figure 1a)

CABLE v-200299-8 TO KEY monULE:

CABLE. V-200208-0 RMS 8 / DSP a

PC_RACK ASSY (K-50398-01)

~ stv (exer Figure la.

Page 7

The Cassette Deck Assembly and its associated mounting hardware is also packaged in a special molded styrofoam box. (See Figure 1b)

CASSETTE DECK ASeEMBLY

ADHESIVE. FOAM RUBBER Hip BE eee. ATER Cant V-200190 IS INSTALLED.

Figure 1b,

Cable assemblies V-200240-1, V~200150-1, V-200236-1, and V-200235-1 are all packaged in a cardboard container placed in the bottom of the master shipping container. (See Figure 1c)

PC RACK Assy. PACKS N STYROFOAM,

CABLES

CASSETTE DECK Assy. PACKAGED IN STYROFCAM

Figure Ic.

Page 8

Cosmetic Graphics are packaged in a separate container which will also contain the specific game package ordered with the MULTI CONVERSION SYSTEM.

CHOOSING THE MACHINE TO BE CONVERTED

One of the most important considerations determining the success of your conversion will be the condition of the machine that you are converting. Obviously, if the picture is dull with its present game; it will be no better with the conversion system. If you have a choice, select a machine that has an instruction manual and/or good primary wiring diagrams.

Cosmetic Considerations: Since it is extremely

important that all visible graphics, original manufacturers name (other than serial number plate), logos and etc are removed or covered by new graphics, a proper choice of cabinet in this phase of the conversion can save you much time.

Mechanical considerations: Make sure the integrity of the cabinet is such that the converted game will not be the vandais dream. Remember that you may possibly be making more game interchanges in this cabinet. Review the control panel to identify what changes will be required so that you will be properly prepared. Make sure there is enough room to install the Multi Conversion system and still have access for service.

Electronic considerations: The Data East MULTI CONVERSION SYSTEM is designed to operate with color RASTER SCAN monitors, mounted in the vertical direction (your home 7V screen is mounted in the horizontal direction). The system also requires four basic power supply voltages. The regulated voltages are + 5 volts, -5 volts, and + 12 volts. Under certain conditions it may be desirable to use an unregulated source of + 12 volts (called +13 volts in technical descriptions).

Page 9

tev stev ‘COUNTER } COUNTER?

out 1 our 6

com 1 CON GND

N20 IN 19

Zz zz2z Some EA

g GETTING STARTED

REVIEW

All of the games designed for use with the MULTI CONVERSION SYSTEM require a control lever (joystick) and at least one pushbutton for action and two pushbuttons for 1PLAYER and 2PLAYFR selections.

Review the interconnection diagram to determine the controls you will be using and the location of

all the components required. sec Figures 2a & 2b)

od COUNTER a CON 4

CoN counTer #2 AY

  • ee ee = 1 steer

ES GN COIN COUNTER 2 §§ OPTIONAL, RIGHT ACODER OMST “oe Saetores Fon err THIS OPTION. uP OPTIONAL FILTER CAPACITOR. DOWN SHOOT 1 SHOOT 2

Figure 2a. mt

REY NODULE 7 Suaiied with Geme RAE)

CASSETTE DECK ASSY wa-50362-2

1 v-ro0aa6-1 el

y-200235-1 To RGB Color Naaieor

y-200239-0 To Bay nodule

y-200150-3 ‘To Cassette Deck Assy [=> 6 ® 7 v-200242-1 i Procte’seusceors Figure 2b J vosgoto-a

Page 10

keview the instruction manual for the game you are converting and determine if you can utilize the power supply currently in the game and also determine how much if any of the present wiring may be used. Refer to the electrical specification section for the MULTI CONVERSION SYSTEM requirements.

The major components that you will have to install will be PCB Card Rack, the Cassette Tape Deck and Power Supply. The card rack and the tape deck assembly should be located for ease of access so that game interchageability and dip switch changes can be easily accomplished.

It is recommended that the card rack be installed vertically as shown, being sure that the component side of the pceb's are facing the inside of the cabinet to provide easy access to the dip switches and the sound volume control. (see Figure 3).

Figure 3

The system will operate with the card rack assembly mounted at any position; however, care should be taken to consider proper ventilation and cooling of the pebs. Heat is generated by the electronic components mounted on the pebs and if the boards are not ventilated these temperatures can cause severe damage to the pcbs.

Page 11

CARD RACK INSTALLATION

There are two metal brackets packaged with screws and placed in the cardboard box with the interconnecting cables. These metal brackets are to be screwed to the sides of the card rack to provide a means of attaching the card rack to the side of a cabinet.

Determine the most desirable location for the card rack and temporarily install it. Try removing one of the peb's from the rack to determine that enough space was allowed for service at a later date.

Locate the power supply to the card rack cable assembly (cable H) and be certain that you have allowed for adequate slack in this cable when it is connected to the power supply.

NOTE

If IS IMPERATIVE THAT THE MAIN POWER LINE GROUND BE ATTACHED DIRECTLY TO THE GROUNDING BOLT ON THE CARD RACK (SEE PICTURE) BEFORE IT IS ROUTED TO OTHER PARTS OF THE SYSTEM.

Figure 4,

Page 12

POWER SUPPLY OPTIONS

Approximately one out of twenty machines that are candidates for conversion have sufficient power supply capacity to operate the MULTI CONVERSION SYSTEM. After reviewing your machine if you need additional power, Data Fast offers two alternate power supply assemblies for your use. They are pictured below.

SWS-60 NDB-O4PS Figure 5a Figure 5b

The SWS-60 switching power supply has sufficient capacity to handle all but the most difficult situations. (see electrical specification section)

The NDB-O4PS Power Supply Assembly includes the SWS-60 as well as an Isolation Transformer (100vac), a Noise Filter, and an Unregulated +12 Volt Supply. (see electrical specification seation)

Connect the power supply to the card rack using the cable supplied (Cable H). Make sure that each connector is properly seated and that the cable is not routed in such a way that it could be damaged by future vibration or equipment motion.(ie across a sharp piece of metal or steel staples)

Page 13

POWER SUPPLY INSTALLATION

The location of the power supply was considered above with respect to the length of the power cable; however, consideration must be given to proper ventilation of the power supply. Proper access of the power supply should also be considered so that voltage measurements may be made and adjusted according to the power supply specifications.

POWER SUPPLY CONNECTION

Be sure that proper fuse protection has been provided for the power supplies and thoroughly review the primary wiring circuit. If necessary, cut the cable ties so that you may trace each wire to assure that it is properly connected.

NOTE

POWER SUPPLIES GENERATE HEAT DURING OPERATION AND MANY NEED TO BE DE-RATED AT HIGHER TEMPFRATURFS. REVIEW YOUR POWER SUPPLY SPECIFICATIONS AND IF THERE IS ANY DOUBT RUN TEMPERATURE TESTS PRIOR TO PLACING EQUIPMENT ON LOCATION.

CUSTOMER-PROVIDED POWER SUPPLY SYSTEM.

After determining that the power supply you intend to use has sufficient capacity, use a voltmeter to assure you have properly identified all of the required output voltages.

Refer to the CAELES section--Cable H (V-200240-1 ) for color code and pin numbers of each of the required connections. Connect the unterminated ends of Cable H (Power Supply-to-Card Rack Cable) to your power supply, taking care that each connection is proper and that each is of the CORRECT VOLTAGE AND POLARITY. Insert the other end of the cable into the Card Rack Motherboard (BUS

  • using the connector provided. Make sure that the connector is properly seated and that the cable is not routed in such a way that it could be damaged by future vibration or equipment motion.(ie across a sharp piece of metal or steel staples)
Page 14

APPLYING POWER

Without any peb's inserted into the card rack, turn the Main Power Switch ON. By looking into the card rack, you will see four LEDs adjacent to CN2 on the motherboard (See Figure 6). One for each type of power required by the DX-1. (+5V=RED, -5V=GREEN, +12V=YELLOW, +13V=AMBER). Note that all four LEDS are lit. Should any fail to light there may be a mis-connection or a fault in the power supply.

CAUTION

DO NOT UNDER ANY CIRCUMSTANCE INSERT PCB'S INTO THE CARD CAGE UNTIL ALL LEDS ARE LIT! DO NOT INSERT OR REMOVE PCB'S WHILE POWER IS APPLIED TO CARD RACK! TO DO SO MAY CAUSE IRREPARABLE DAMAGE TO THE PCB'S AND WILL VOID THE WARRANTY.

After determining that all four LEDs are lit, turn the Main Power Switch OFF. Insert the pcbs into the card rack. Determine that all four LEDs are still lit, if so turn off the main power switch and proceed with further interconnection.

Page 15

CONNECTING THE SPEAKER

Cable C (V-200236-1) is provided with unterminated leads for connection to your speaker. Sound is generated in the RMS-8 PCB and is available at CN-1. Cable C is provided with a connector compatible with CN-1.

QUICK SOUND AND SYSTEM TEST

Adjust the Volume Control (located to the left of CN-1) to its mechanical mid-range. Make sure that all the switches on DIF Switch 1 are in the OFF position and that there are no cables connected to the BIO-8 PCB. Turn the Main Power Switch ON. A two-tone alarm signal should be heard in the speaker.

Figure 7. Volume Control

CONNECTING THE VIDEO MONITOR Video is generated in the DSP-8 PCB and is connected to the monitor via connector CN-1. Cable D(V-200235-1) is supplied with a mating connector to CN-1 on one end and unterminated wires on the other end (See the cable section for color coding and pin numbers). Connect the unterminated wires to your monitor inputs, being careful to ensure that all connections are made correctly and are routed to protect these video cables from the extremely high voltages that exist in monitors.

Page 16

CONNECTING THE VIDEO MONITOR

Turn the Main Power Switch ON and wait a sufficient time for the monitor tube to reach operating temperature. You should see a blue background picture with the following large sized words DECO CASSETTE SYSTEM printed in red. Following that, smaller white letters should show WAIT UNTIL COUNTER READS 000 THEN GAME START (See illustrations in Trouble Shooting Section). Any other colors than blue, red and whiter indicates that an error was made in connecting the video wires and should be double checked. If there is un-decipherable video on the screen, the Vertical and/or Horizontal Hold adjustments on your monitor may have to be adjusted to display the picture described above.

Should the picture be stable but turned upside down or backwards, the wires to the Deflection Yoke may have to be reversed. Refer to the instructions for the specific monitor you are using.

If the position of the picture is oriented severely off the screen or an extremely unstable picture results, the Sync Signal Input to the monitor may have to be changed from its original position to the Horizontal and Vertical Negative syne position.

INSTALLING THE TAPE DECK ASSY

Using Cable E(V-200150-3), install the Edge Connector onto the peb of the Tape Deck Assy. You will be able to see the peb by looking through the rectangular hole in the back of the Tape Deck Housing. Then remove the adhesive-backed foam rubber strips from the cassette deck styrofoam box and install the strips to each side of the rectangular hole so as to provide an effective dust seal for the tape deck assembly. Insert the other con-_ nector into CN-2 of the RMS-8 pcb. (See Figs. 8a & 8b)

Figure 8b. Figure 8a

Page 17

INSTALLING THE GAME KIT

DIP SWITChES One of the most important aspects of installing a game kit is making sure the DIP switches are properly programmed. Incorrect settings can prevent the system from operating. Since the main microprocessor samples these switches when the main power is applied, always test the system reloading after changing any switch position. This test is accomplished by turning the Power Switch OFF and after a 10 second wait turn the Power Switch ON again. Normal tape reloading should occur.

The LIP switches are located on the RMS-& PCR, adjacent to the Volume Control. Typical DIP switch settings are shown in Figure 9.

RH COIN SELECTOR (TYP — OFF} SPECIAL PURPOSE (TYP. 6 ON. 7 & 8 OFF) i LH COIN SELECTOR : (TYP-OFF) DIFFICULTY TAPE DECK BONUS POINTS - SSS T= MUST BE LEFT OFF] COCKTAIL/UPRIGHT NUMBER OF ROCKETS, MEN. ETC: COCKTAIL — BOTH OFF UPRIGHT — BOTH ON Figure 9,

INSERTING THE TAPE

Install the microcassette tape into the tape deck, "A" side up. Close the the top of the tape deck housing and proceed to the installation of the Key Module. (See Figure 10)

Figure 10.

Page 18

CONNECTING THE KEY MODULE

The key Module must match the tape installed and must be installed properly or the tape will not load. It is connected to the BIO-3 through cable V-200239-0 (See Figure 11).

Figure 11

Page 19

COSMETICS

All components that contain any possible original manufacturers name (other than the serial number plate), graphics or game information must be removed or covered by some means. Do not destroy or discard the Header Plex (top flashing), Control Fanel and or Monitor Plex or Glass as these items may have to be used or modified for your conversion.

The Control Panel and Monitor areas are probably the most important components of your conversion since they are the main interface between the player and the game. The Control Panel: If the control panel has a joystick that is convertible from 4 way to @ way action (and vice versa), one or more pushbuttons for "SHOOT or ACTION", and two pushbuttons for {PLAYER and 2PLAYER selections you are ready to proceed to CONTROL PANEL OVFRLAY INSTRUCTIONS. Any mechanical modifications, such as adding a joystick, should be accomplished before installing the control panel overlay. A template has been included as an aid in locating and drilling for a WICO joystick (See Figure 12a). A GREENLEE Radio Chassis Punch (available at electrical supply store and some hardware stores) produces a quick and clean large hole for the joystick shaft to go through (See Figure 12b).

Figure 12a Figure 12b

Page 20

CONTROL PANEL OVERLAY INSTRUCTIONS: The generic Lata East Control Panel Overlay supplied, has been specifically designed to retain the player controls within the two sets of lines printed on the overlay. It is shipped with a very strong adhesive applied to one side which is protected with an easy-release paper backing. Since the overlay is oversize, carefully position it over the control panel before removing the protective backing to determine exactly how it will be installed. Remove the backing and apply the overlay to the panel as it was positioned above. Smooth the overlay from the center of the panel towards the edges being sure to remove air bubbles as you proceed. The excess overlay material at the top and bottom of the control panel should be wrapped around the edges to prevent players from peeling the material off. All holes may be cut and other excess overlay material may be trimmed using an Exacto Knife or razor blade. Carefully apply the appropriate pushbutton decals and install new pushbuttons according to the schedule below. 1PLAYER, 2PLAYER Yellow SHOOT 1 (Fire, Action) Red SHOOT 2 (only when reqd@) Blue

THE MONITOR PLEX OR GLASS: Many games have been manufactured with graphics screen printed to the back side of the plex. These graphics must.be removed or a new clear plex installed. One method of removing the screen printed material is to soak a rag in lacquer thinner and wipe the plex clean. It may take repeated applications of the thinner to completely remove all traces of the graphics. An oversized black Cardboard Underlay has been supplied to be placed under the monitor plex. Using masking tape, temporarily align the viewing hole of the underlay with the monitor screen. Mark and trim the excess cardboard as required.

Page 21

CABINET SIDES AND FRONT: Many techniques are available to prepare the cabinet for conversion. A few are listed below: SIDE DECALS- Remove carefully using heat gun or cover with paint. REPAINT- Paint over all graphics using a conventional roller and latex based paint. Use a sufficient amount of paint to totally cover all previous graphics. APPLY NEW GRAPHICS- New side graphics have been included in the kit which will provide new color and may also cover up some types of old graphics. HEADER PLEX (TOP FLASHING): A new marquee with game graphics is supplied with each of DATA EAST'S game kits. Due to the large variety of sizes of header plex's used by the various game manufacturers, you may have to cut the marquee to Size using an appropriate saw. In some cases the marquee will be too small to completely fill the opening left after the removal of the original plex. This may be solved by removing the screen printed graphics from the original plex (see monitor plex) and mounting the DATA FAST marquee be~ hind it. If the original plex is longer, you may wish to saw spacers from the original plex. Paint them black and put them on one or both sides of the new marquee.

Page 22

TROUBLE SHOOTING GUIDE

1, FUNCTIONS

THE THREE PCB'S DO NOT FUNCTION AS A GAME UNLESS

TAPE PROGRAM IS LOADED TO THE PCB'S.

SP

MOTHER BOARD

ac Sowce

STRUCTURE

Page 23
  • INDIVIDUAL FUNCTION OF EACH BLOCK
  • CONTROL CPU AND ITS RELATED CIRCUIT
  • COLOR SIGNAL GENERATOR AND CONTROL
  • STANDARD PATTERN GENERATOR AND TIMING SIGNAL GENERATOR
  • CPU CLOCK
  • STROBE SIGNAL
  • DYNAMIC RAM TIMING SIGNAL
  • CRT TIMING SIGNAL GENERATOR
  • HORIZONTAL
  • VERTICAL
  • SYNCHRONIZE
  • DISPLAY CONTROL
  • MISSILE GENERATOR AND CONTROL
  • MIXMODE GENERATOR AND CONTROL
  • MAIN GRAPHIC GENERATOR AND CONTROL

RMS 8

  • DYNAMIC MEMORY (48 K BYTE)
  • PROGRAM
  • DISPLAY
  • SOUND
  • CPU
  • ROM/RAM
  • SOUND CHIP
  • MIXING
  • COMMUNICATION WITH MAIN CPU
Page 24

3)

4)

1)

2)

3)

4)

5)

6) RESET SIGNAL GENERATOR

DIP SWITCH READING

BOOTSTRAP ROM

CONTROL PANEL SWITCH INPUT READING

COIN SWITCH ACTIVATION READING AND COIN COUNTER DRIVE

NMI GENERATION FROM SERVICE/COIN SWITCH ACTIVATION

VOLUME INPUT AD CONVERSION

BACK DISPLAY CONTROL

  • READING/WRITING PUNCTION FROM CPU TO MEMORY
  • HEAD LIGHT MODE
  • DISPLAY HORIZONTAL/VERTICAL SHIFT

CASSETTE DECK INTERFACE

CASSETTE DECK

  • GAME PROGRAM LOADING

DC POWER SOURCE

  • SWITCHING REGULATOR

+5V (REGULATED) 6A +12V ( u ) 1A +13V (UNREGULATED) 2A -5V (REGULATED) O.1A

IF REGULATED +12V, 3A COMBINATION IS USED IT ALLOWS

+13V UNREGULATED POWER USE.

Page 25

DECO CASSETTE SYSTEM

TROUBLE SHOOTING GUIDE

TURN

POWER

ON

DOES BLUE BACKGROUND APPEAR

SEE FIG.#1

YES

DOES COUNTER ISA CASSETTE DO POWER LED'S LIGH ON CARD RACK REFER TO SOLUTIONS

NO | #3,#4,#5

DOES REFER TO

ERRORAPPEAR ONMONITORSOLUTIONS
DISPLAYEDTHE SCREENFILAMENT

GLow #6,47 SEE FIG.#3 SEE FIG. #2

YES

REFER TOae ]| REFER To

SOLUTION YES caenecreD |NO_| SOLUTION

#1, #2BETWEEN PCB#8

AND MONITOR

te veRiE DOES GAME REFER TO

THat cane [YES | APPEAR SOLUTION AFTER

I'sAPROX#9

FUNCTIONING Or ehuTeS

J [re REFER TO pt Tee SOLUTION COUNTER STOP AT A #9 PARTICULAR NUMBER

ERROR 1S FLASHING REFER TO CASSETTE ERROR SEE NEXT PAGE FOR SOLUTIONS

Page 26

OPERATING PROCEDURES, SOLUTION GUIDE

SOLUTIONS

#1

#2

#3

#4

#5

#6

#7

#8

#9 CHECK DIP SWITCH SETTINGS

SETTINGS MUST ALWAYS BE

CHECK KEY MODULE CONNECTION

CHECK FUSES

CHECK AC INPUT TO SWITCHING REGULATOR 100V.AC AND

DC OUTPUT +5, -5, +12

ASSURE POWER IS CONNECTED TO CARD RACK

CHECK MONITOR POWER CONNECTOR FOR 100V.AC

CHECK MONITOR FUSES

CHECK VIDEO CONNECTOR

EXCHANGE PCB'S

Page 27

DEC QO

CASSETTE

SYSTEM

WAIT UNTIL COUNTER BELOW READS 000 THEN GAME START

DEC O

CASSETTE

SYSTEM

CASSETTE ERROR!

  • BLUE BACKGROUND

<—REFER TO ERROR GUIDE

#59

CASSETTE

SYSTEM

Page 28

CASSETTE ERROR GUIDE

ERROR CODE SOLUTIONS

OL 1,8,9,3

02 3,4,5

03 3,4,5

04 3,4,5

32 2,3

33 5

52 8,9,4

58 3,4,5 59 6,778

CASSETTE ERROR SOLUTIONS

#1

#2

#3

#4

#5

#6

#7

#8

#9 CHECK THE TAPE AND MODULE GAME NAME TO INSURE THEY ARE PROPERLY MATCHED

CLEAN THE TAPE DECK HEAD WITH ALCOHOL AND COTTON SWAB

CHANGE THE CASSETTE TAPE

CHANGE THE CASSETTE DECK

IF THE ERROR PERSISTS CHANGE THE BIO-8 BOARD

CHECK THE TAPE DECK CONNECTOR

CHECK THE KEY MODULE CONNECTOR

CHECK THE TAPE TO INSURE SIDE "A" IS FACING UP

CHECK THE TAPE TO INSURE THAT THE TAPE IS ON THE SPOOL OPPOSITE THE CAPITOL "A", IF NOT ADVANCE THE TAPE TO THE CORRECT SPOOL WITH A SCREWDRIVER

Page 29

ELECTRICAL SPECIFICATIONS

Input Power Requirements:

Regulated +5volts 5 amp. Max -5volts -2 amp. Max +12volts 1 amp. Max(logic only) Unregulated +12volts(+13volts) Sound -75 amp Max. Coin Counter *(customer determined) Coin Blockers *(customer determined) *see Power Considerations below

Video Requirements Color Signal RGB Black 0 to +2v Image +2.5 v to +4v Syne : ie} 0 to +.5v 1 +3v to +5v

POWER CONSIDERATIONS

Connection and use of Coin Counters and Blockers are beyond the control of Data East and therefore should be given special consideration by the customer.

When Data East offers the SWS-60 Power Supply Option, it does so on the basis that the +12volt and the +13volt lines are jumpered together and the regulated +12volt power from the SWS-60 powers all 12volt components. In the event a coin counter that draws excessive current is connected to the system, actuation of this circuit could cause a temporary memory failure and a malfunction may occur. An optional capacitor as shown in Figure 2a may alleviate this problen.

Page 30

MECHANICAL SPECIFICATIONS

The following drawings provide all the necessary dimensions for the mounting of the Multi Conversion Kit.

MOUNTING BRACKET

CASSETTE PLAYER A975 rr

2375

  • 5.25 7 198

CASSETTE PLAYER

DIMENSIONS FOR INSTALLATION

Page 31

2.0 CLEARANCE FOR CABLES

DIMENSIONS FOR INSTALLATION.

Page 32

CABLE SECTION

  • PCl RMS8 CNL

PS= RMS8 fa S-VH

CABLE C V~-200236-1 To Speaker

SPEAKER- (GND) BLACK

SPEAKER+ WHITE

  • PC2 DSP8 CN1

CABLE D V~-200235-1 To RGB Monitor

TV.B BLUE

TV.G

TV.R

TV.GND Ailun/|s|/win | SYNC

Page 33
  • PC3 B108 CN3

Ye ee p62, > if o | PAZ [oR ee a ee ee pay Poe

IAi2 | 412 L/w | MOLE x 1625-BR- OLEX M 1625 -15P—

PGCE SHOOT 4 [| CY | SHOOT 2 PT R p Pi | BR [| A21 |TERM.6D./1T1 | _| BLOCKER’ |_|

Page 34
  • BUS 10 CN2

MOTHERBOARD

Bus 10 B8PS-VH

CABLE H V~200240-1 To Power Supply

"465 ORANGE

RED

PINK

BLACK

BLACK BLUE

RED

connected internally on BUS 10

connected internally

on BUS 10

Page 35

K-50598-0

| NOS [DESCRIPTION CN_SUPPORT PARTS" NOS. k-50216-3 2_| SIDE PLATE(R 3_| SIDE PLATE(L 4 SIDE PLATE SUPPORT. PCB STOPPER GUIDE RAIL WING BOLT sw4 P-59514-0 50-1030

DE-0096 DE-0097

Page 36

CASSETTE DECK ASSEMBLY

[p-50950-0 | 2 [ CASSETTE BRACKET [K-50141-2 | 1 | [RUBBER SHEET | P~50769-0 [| [casserze DECK [MD-3a_ [|

[SCREW TP3x8 | [screw 3x6 |

Page 37
  • PC3 BIO8 CN3 (Ati nA)

HIF3~50p~2.54DS

ey NeFELerm |
Ali} GNDBl
A21p(R)B21p (L)
A31lp(u)B3 ,lp (D)
Adlp SHOOT 1B4lp sHooT 2

AS | BS

AG2p(R)B62p(L)
A72p(U)B72p(D)
[a82p SHOOT 1B8_ |_2p sHooT 2

aa B9 Al0 B10

AllBlllp
Al22pB12SERVICE SW
Al3GNDB13GND
Al4COIN SW 2B14
AlSCOIN sw lB15

Al6é GND B16 GND

Al7BLOCKER 1B17BLOCKER 2

Al8 B18

Al9 B19

A20COUNTER 2B20COUNTER 1
A2l_ | +13vB21+13V
GNDB22GND

B23 B24 B25

#) #—AMC Lo SHOOT SW1 (#Re *Y) , SHOOT SW2 (Hx EEBKLESM, 24» F1F ROB SHOOT SWI ( BY) CHRLTFS.

Page 38

ON1 MOTHER BOARD

RAY A

DS TLY102 Dé TLRI02

  • Be TLAIO8 a (Ae) rasa] ah (p23) D9 RD36FB

OOOO ~8aa] AAT

ou fAnT-AGG

+419

  • +12 t-Or5

GND to om < as oe

@e| Bo os ia)

sc] tt | |< } jocor

' x xan uw > jin. +

Page 39

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 40

sEESBENSRBIISSSENEASEHUE [>] Reezasa oye ONZE IRESARAMRI RSE GiaRRRKEREM fever Le Sete S

| scl od =i dol a = NR) 9 See

ant H [jSeSImi A 684 ARAN

A RG) Tes } I IF]

Page 41

rad | > i.

cue tree ES Sao | EE COTES FRR

: - ; +

5 SBSSSEse ceateaaad

Page 42

ts CCS amare peel _ ots 2 7 2c cee i coy tt ete fil c ee io a woe ECL | Sr cin

= i ran a OR can oe 0 ede] He 2 rm mx: Rad (OD wD led BO ead 1H soe For sd ts Com a ad a a Tg we § joes jem aeeela—e tee we te *

Wee ret EFFA EAE REFEREE

oa oo pet fey Ft —* rey) ey ec Oy a me A a wg ELA batt Ww By a Ee Ee in n aoe Fy ates ay COME Oa

el tll oo fo ll CO 8 S| t—-F TT evan iN ta if

Page 43
  • ae LALA : ge Sar Pd | og on aia SEE. oath wees a oi

percep gts Bh SC AMaweee ss ui re ERRVTRRAT isuscsesaccsionas BaegRSeSRORRNRUOUTNNS le) Rg { — zl wes as COCCC eee Ei

a: Peery fi Ald sun ou ou

  • a‘ one 57)
Page 44

BB 22S Kee

es SN je = | ee ) ee

ks] z E48 Tihs 3223 eae ' = 4 LE HOEY VYY

z Rabe SESE 28 a tbe vi ze a at q le

Page 45

CHANGING A GAME Is EASY

AS

  • CHANGING THE TAPE
  • CHANGE JOYSTICK TO PROPER SETTING- (2 WAY, 4 WAY OR 8 WAY). ON DATA EAST SANWA JOYSTICK THIS IS ACCOM- PLISHED BY USING PROPER RESTRICTOR.
  • CHANGING THE KEY MODULE
  • SETTING THE DIP SWITCHES
  • CHANGING THE TOP FLASHING

(HEADER PLEY)