Cops CO-398-01 1st Printing
Cops (USA) (Atari Games, 1994) · Change Order · 8 pages · 9 sections · original scan
JAK
ATARI
GAMES oe TIME WARNER INTERACTIVE ©
rs
Tips on Us
CO-398-01 1st printing
ing the COPS Self-Test
Supplement to the COPS Operator’s Manual (TM-398)
HE GUN CALIBRATION procedure in the Cops™ game was designed differ- MA ently from similar procedures in other games. This supplement explains the procedure in more detail than what is printed on page 2-4 of the COPS Operator’s Manual. It is very important that the gun is correctly calibrated, since this adjustment directly affects earnings. The alignment has been set at the factory. It should not require adjustment unless a new COPS Logic PCB or gun has been installed. “ In addition, this game has a different NTSC board than is shown in the
© 1995 Atari Games Corporation. All rights reserved. 3/95 COPS Operator’s Manual. Therefore, this supplement includes revised Figure 5-1 (Game Wiring Diagram, sheets 2 and 3), Figure 4-2 (Cabinet-Mounted Assemblies, Rear View), and video adjustment procedure. # Also, the gas pedal has been deactivated in the drive mode, to improve the game play.
If you need technical assistance, call your distributor or Atari Games Customer Service at: (408) 434-3950 Atari Games Corporation, 737 Sycamore Drive, Milpitas, CA 95035 (Monday-Friday, 7:30 a.m.—4:00 p.m. Pacific time)
A Barbour Langley Production USA ™ and © 1994 Nova Productions Limited. All Rights Reserved.
Licensed to Time Warner Interactive Inc,
SUPPLEMENT “ Tips ON USING THE COPS SeLe-Test
New Gun Alignment Procedure
Preliminary Steps
- To enter the Test Mode, press the Service switch located inside the coin door.
- Press A so that the Set-Up screen appears.
- Press C once to start the set-up. A frame and crosshairs appear on the screen.
- Press B twice slowly until Gun Setup appears in the alphanumeric display.
- Press C to start the gun set-up.
Gun Set-Up Procedure “1. Shoot Centre appears on the alphanumeric display. While seated in the game, hold the gun approximately 18 inches away from the screen. Aim at the center of the crosshairs in the middle of the screen; pull the trigger. (See Figure 1.)
here’ Figure 1 Gun Alming Location (Center of Crosshairs) ?
- Test Aim now appears on the alphanumeric display. The video now displays a building exterior: see Figure 2. Shoot the gun at the center of the screen (at the midpoint of the left column), and note the display of the shot fired in relation to where you aimed the gun.
ded when the ied at the orna teft column.
Figure 2 Example of Where Shot Landed When Gun Was Aimed at Center of Screen
As an example for this test, we will use the shot's position as 2 inches to the right and 1 inch up from the gun’s aim point. This is only an example: your results may vary. . Press B and aim the gun at the Shoot Centre crosshairs screen, about half the distance it is off in the opposite direction of the error. This avoids overcorrecting the aim. In this example it would be 1 inch to the left and 1/2 inch down from the center of the crosshairs:
Point gun here to compensate for error, and pull trigger.
Figure 3 Location of Correction Shot
Tips ON UsiNG THE COPS Setr-TesT SUPPLEMENT
- In the Test Aim building scene, shoot at the center of the screen. Again, use the approximate midpoint of the left column of the building as a center reference, and various points around the screen to test the gun’s aim.
- Repeat steps 3 and 4, gradually increasing the correction distance in step 3, if necessary, until the gun's error is minimized.
- Press C to lock in the setting. Otherwise all adjustments will be lost. Set Up Complete will appear on the alphanumeric display.
Final Steps
- Press A or B to re-enter the menu.
- Press the Service button once to exit ihe test. 3, Press and hold the Service switch for several seconds to exit the Test Mode and re-enter the laser player, CD-ROM, and checksum tests. After about 20 seconds, the game will go into the attract mode and be ready for play.
New Video Adjustment
Procedure
The COPS game now has two video control boards that replace the single NTSC Decoder PCB shown on page 4-4 of the COPS Operator’s Manual. The two new boards are the NTSC Decoder Board and the Video interface Board. Due to this change, on the following pages are the revised game wiring diagrams (sheets 2 and 3 only) and the revised cabinet-mounted assemblies drawing. We recommend you keep this supplement with your COPS Operator's Manual. The two new boards require a different video adjustment procedure, should you ever need to correct or improve the Hantarex Polo screen image. Follow this procedure: Video Interface Board y
- Test Mode: Enter the test mode by moving the shunt on the Test header to the on position. Verify that you see a white raster on the screen. 2, Contrast Setting*: Adjust the contrast control (RV405) on the Remote Control Board to display a white raster on the screen.
- Disable Controls*: Disable the controls on this board by removing the control stems from the brightness (RV406) and contrast (RV405) controls. 4, Test Mode: Move the shunt on the Test header back to the off position.
NTSC Decoder Board
- Brightness: Adjust the brightness (BRI) and contrast (PIC) controls until the brightness range of video display images looks normal. This adjustment should be done using both day and night scenes from the game’s laser disc.
- Color: Adjust the color level (COLOR) and tint (HUE) controls until the color saturation and the color tones of the video display images look normal. This adjustment should be done using scenes with characters to verify that the skin tones are set correctly. Also check the green color in the night scope scene (this appears 10 seconds from the beginning of the attract mode).
- Noise Rejection: Adjust the detail sharpness (SHP) control until the chroma noise in the video image is minimized. The picture should appear sharp (in focus) without excessive noise visible.
Revised Gas Pedal Wiring
To improve game piay, the gas pedal switch is shorted closed at all times. This avoids players causing a braking effect when lifting their feet off the gas pedal, which could negatively affect game play.
ATARI
GAMES TIME WARNER INTERACTIVE
SUPPLEMENT * TIPS ON USING THE COPS SeLe-TrsT
Zz i= } = B[-weeeel Efa-l 7) azaene. 2h
| 882585 | 893 | come |
Key ALPHANUMERIC vioco no manu INTERFACE a
| ° | 5 | BOARD |
| sek, | 3 | es |
| 2328 | z | ra |
| 3328 | gaees | aeg™ |
ersaen i ginvoreereoteteze] low aae| glerens) glo = so] ' é fd “Ba | Zz) | F|
| ECP | ERCELLEEE | ages | as 2/2 |
! =| Lyd y
| EEECEEGOREE | EE | allel | aig| >| sla |
| B[-saemonaatt | lett | ebee | RaEaRS| |
foro GR formes Ge Towns GR ‘OFF ROAD 2 . (OFF ROAD 1 [ormow: G3 ___ sverreeranan (<a Taroommee CB
pat pan
vm ‘YOR vw yew OnBK YiGN yeu vw. visy wy arveran ~ ta rnc ae rer ae BULLET 2 Gy BULLET ft om | ‘OFF ROAD 4
OFF ROADS. OFF ROAD ae
onek ORBN ‘ORR ‘oRW ony ‘ORGN oneaU oR.
‘OnBK YIOR BEEEEE yicy g 5 Fut UA, RW RY IGN
rao rnernaad
Figure 5-1 Game Wiring Diagram, Sheet 2 (revised) 053830-01 Rev. C oniGy @vBU wy
GYIGN
Tips on UsiNG TH COPS Stir-Trst ¢ SUPPLEMENT
E
a wi | 1 | CSYNC cGno @+8K 2 sate o+¥
| 3 |ano | viveo | av epee |
4 | eu DISPLAY
| 5 | GRN | 5 | vlolol 88 | | 8) 8) = | ||
| - | 6 | RED | voz | | a. | TI | | |
| ; ner | Slawo] | 53 | (c= 9) | (owaee] | ||
| | INTERCONNECT | & | Fi | a | t | — |
ee 8 4 z30e
| | newore | Bless | az | £8235 |
| | CONTROL, | 42 | 7 | |
| BOARD: | * ba | x |
i | & > ON ig, : tf 407 Es
| Bu pee | 3 oe | 5 Sz | NTSC DECODER BOARD |
| I | 2 | ——— |
Rires zee)
| J | | | ] |
| i: | ae | A |
ow Ter Wh PowER SUPPLY wiogo INPUT FROMLASER Isc PLAYER e
EO a of
| Le | 28 | « | Pa |
5 §
| + | a8 | 8 | 3 | 55 | gs |
| noun | (OS | ( | Ee | L} | g |
| | PS) ewevawe | ¥ | 288 | |||
| = | 1 | zea | 7 | 7 | |
| =— | BLUE LAMP | oe coat | 39 | ia ee |
oe a ' i RED
| ue | Ga | moun | ert | 32 | F |
| «| =| 8] >| | oe | Ce | 3 S| > |
Zleane How) flow) Blew) FL) FL
| gee | F] | 3 | g | ||
| 88 2/5 | gy | Bs! | 88s | slg] | as |
pd bd
| elf | g | zl | g | ||
| 5 58 5 | CC | Ce | ee | ||
| RARE | a8 | zR | Ra | aa | 8 8| |
Figure 5-1 Game Wiring Diagram, Sheet 2 (revised) 053830-01 Rev. C
SUPPLEMENT % Tips ON UsinG tiie COPS Setr-Test
i
| ' | SHAKER | steennc | | | ||
| \ | MOTOR | Por | | | ||
| | | —~, | _ | ' | ||
| 360 | 4 | | “FR | |||
| wen, | went | Wren | a | x | ! |
| iis | R | | _R | | | xz | i |
| 3 LwaK | wax |? | wk | = | i | |
| eK | ° | BK i: | 8k | |||
| WR | nw! | Taw | |||
| 5 Taw | | | ony |® | |||
| 6 | i | 6 | CONTROL | ||
| 7] | TP) Uh | RT SL |
8 | ow ° :
€ 5|5|8
3/8
-—|-|-0— 1 i ' | Foor | | PEDAL | i} i i}
com fey counTer o¢
men) PSS
7 peu. 2 pep
| a ae | wich _/, | |O8 | e | SERVICE SWA |
| «ren | we]? | | yt | SERVICE SWB |
| 5 Hin | wwe]? | | SERVICE SWC | |
| ers | a |X. | SERVICE ACCESS | |
| ; | ° | 8K | ® | [eK |
oH, $ seurstesr
Pss
on : a}? 2
| 9K | —) | com |
| 10 | wo? | DOOR |
GNY 12} Mte °
Figure 5-1 Game Wiring Diagram, Sheet 3 (revised) 053830-01 Rev. C
Tips ON UstnG THe COPS Seir-Test * SuppLemet
NOTES:
/\ ALTERNATE PIN-OUTS FOR EDGE CONNECTORS: Loic BOARD
PIN® ALTERNATE = PIN@ = ALTERNATE,
| - | 5 | 1 at | A B41 |
2 Az 8 B2 3 Ag c Ba 4 aa D Ba
| rr] | 5 AS | ry) | |
| 58 | 6 as | F a6 | |
| Ez | 7 AT | H a7 | |
| , og | t | a AB | J Be |
| 22 | 9 Ag | K Bo |
10 ato of ok B10 " an) ow an An N B12
| : | 3 Ang | P B13 | |
| x | 5 | 14 an | a Bi |
15 ats Ss "B15
| CD-ROM PLAYER | He rer | : ie |
7 aq ui. Bw
| Bc INPUT AuDI0 OUT | 18 AmB | v B18 |
| 1 | | 19 ang | we B19 |
| leoae!l [pwoe | 20 A720 | x 80 |
n an yp pea
| a | 2 An | z + Bm |
| a | 2 a2 | a B23 |
| Fi | 2 Az | b ov pe |
| by | 2 Ag | cag 78s |
28 Am a 826 2 aq :
| 1 | Laser oIsc | 8 ref | 7 |
| 7 | PLAYER | 2 A29 | nh. BZ |
30 30 oF 3 B80
| : | at Ast | k f Bat | |
| 5 | 32 AR | 1 * paz | |
| & Hoasues | pa | 2 ass | ™ B33, |
| 7 | —e) sksack | “ ase nod | |
| 7 ewes (9) | Press | po Bas | |
| » LOABLES | @) rep sack | 38 AS | r 536 |
i N to Psmieuws
R R " 12 Loe on a 2 ee aU 3 we v 20) Fis-232 w w 5 INPUT yiDEO
| 5 | tw 1 | ourPur |
2s o——— tonse DECODER BOARD
To 120 Ac ‘OUTLET ia
=—_7—______
Figure 5-1 Game Wiring Diagram, Sheet 3 (revised) 053830-01 Rev. C
SUPPLEMENT *% Tirs ON USING THE COPS SuLr-TEST
| 72-5508 | 175014-1050 | 059786-01 | 72-5520 |
| 1/4-20x.5"Lg. | 1/4", 281" x 625" | ‘Speaker | 174-20 x 1-1/4" Lg. |
| Hex-Head Screw | Flat Washer | Mounting Bracket | Hex-Head Screw |
| (4 Places) | (4 Places) | (2 Places) | (4 Places) |
| 148022-001 | 175017-2025 | 175014-1050 | 175017-2025 |
| 4-1/2" Enciosed | —_1/4* Split Lock | 1/4", 281" x.625" | 1/4” Split Lock |
| Speaker | Washer | Fiat Washer | Washer |
| (2 Places) | (4 Places) | (4 Places) | (20 Places) |
053787-01175014-3040 82-8008B
| Speaker | #10, 219" | 5" Blk, #10-32 x 5" Lg. Bik. |
Cover Plate Flat Washer Button-Heaa Screw (Places) (4 Places) (4 Places)
osto24-02 1! ™ Blue Seat | Side Panel 72-5912 | Decal See Attraction Detail 5/16-18 x 3/4" | (2 Places) At Right Hex-Hd, Screw | (6 Places) 175017-2031 5/16" Split | Lock Washer | (6 Places) 175014-1056 s/i6", 344" x 688" Flat Washer (6 Places) |
053799-01 Seat Pedestal 82-8328 - 318-24 x <2 1-3/4" Lg, Black - Button-Head Screw (4 Places) 2 175014-3063 —_ 9/8", 406" x 812" - Black Fiat Washer - (8 Places) 177000-149| 7 x 3/8-24 Hex Nut | 5 Rear lots (4 Places) Door
| 176020-220 | (2 Places) |.“ | —_ |
#8 x 1-1/4" Lg. ‘A053757-01
| Black LPW Screw | cueae at | 053759-01 | Fan/Power | ||
| (4 Places)| | Part of | | Hamess | Assy. | Wood Cabinet | Bracket Assy. |
| Video | aaeagen or | tssoi-n8 | 038158-01 | 176015-110 | |
| Display | ; | Product I.D, Label | #10 x 5/8" Lg. | ||
| 72-8410S | pce Interface | Lower | 049514-01 | Cross-Recessed | |
| #4 x 5/8" Lg. | Assy. | Right Side | UL Label | Self-Tapping Screw | |
| Cross-Recessed AB | A053858-01 | bits brtars | 042452-0 | (3 Places) | |
| Pan-Head Screw | Video Interconnect | 053911-01 | reed | |||
| (4 Places) | Harness Assy. | Lower | Label | ||
| 17504-7068 | 171132-003 | ee | Lacapeaay | ||
| Fiber Washer | Nectec NTSC | 053951-02 | |||
| (40r8 Places) | Decoder PCB Assy. | Fuse Replacement |
A053861-01 Warning Label Power/Gate Harness Assy.
Figure 4-2 Cabinet-Mounted Assemblies, Rear View (revised) A053750-01 Rev. J