CATHODE RAY TOMES

Asteroids Deluxe TM-165 1st Printing

Asteroids Deluxe (rev 3) (Atari, 1980) · Technical Manual · 56 pages · 48 sections · original scan

Page 1

TM-165 4st printing

Operation, Maintenance and Service Manva!

Complete with Illustrated Parts Lists

Yos™

Page 2

GAME SERIAL # IDENTIFICATION TAG

TV MONITOR

ASTEROIDS DELUXE GAME PCB

REGULATORVAUDIO PCB

GAME SERIAL NUMBER LOCATION

Your game's serial number is stamped on a piate on the outside of the game. The same number is also stamped on the chassis of the TV monitor, Regulator/Audio PCB, and tne Asteroids Deluxe™ Game PCB. Piease mention this number whenever calling your distributor for service.

Page 3

Operation, Maintenance and Service Manual

Complete with Illustrated Parts Lists

Published by: a ATARI INC. y oe 1265 Borregas Avenue * ¢ @

P.O. Box 427 : Ptronics

Sunnyvale, California 94086 Amusement Distributors. inc 245 S. PLUM Ia TUCSON Ag ages (602) 624-2826 Copyright © 1981 by Atari,Inc. All rights reserved.

No part of this publication may be reproduced by any mechanical, photographic, or electronic process, or in the form of a phonographic recording, nor may it be stored in a retrieval system, transmitted, or otherwise copied

for public or private use, without permission from the publisher. ATARI

Lithographed inthe USA. 2K A vWorne: Commutications Company

Page 4

Table of Contents

1 Location Setup A. B. Cc. New Parts 1 Game Inspection 3 Game Installation. . ss 3

  • Line Voltage Selection ....... os 3
  • Interlock and Power On/Off Switches 4 Self-Test Procedure .............. 7 Option Switch Settings . @
  • Bonus Play Feature... - 9
  • Coin Mechanism Multipliers .......... 00.00 e cece eee eee 10
  • Examples of Option Switch Settings . +. 10 Game Play .............0ee eee
  • Attract Mode
  • Ready-to-Play Mode
  • PlayMode ..........
  • High Score Initial Mode

2 Maintenance and Repair A. B. c.

mmo

G. Cleaning... 66... cece nee e eee n tenes Fuse Replacement Opening the Control Panel .... 16

  • LED Start-Switch Replacement 17
  • Leaf-Switch Replacement -17 Monitor Removal Fluorescent Tube Replacement . . Printed-Circuit Board Replacement .
  • Game PCB Removal .............000 eee eeee
  • RegulatoriAudio | PCB Removal . a Game Operation... 2.6... cece ee ee cet enter ee

3 Illustrated Parts Lists \llustrations and parts lists begin on page ............... eee ee eee 23

Page 5

Figure 1 Figure 2 Figure 3 Figure 4 Figure 5

Figure 6 Figure 7 Figure 8 Figure 9 Figure 10

Figure 11 Figure 12 Figure 13 Figure 14 Figure 15

Figure 16 Figure 17 Figure 18 Figure 19 Figure 20

Figure 21 Figure 22 Figure 23 List of Illustrations

Overview Of Game... 6... ee cece ence een e eee 2 Installation Requirements ..... 3 International Line Voltage Selection. 4 Interlock and Power On/Off Switches .......... a) Location of Self-Test Switch, Volume Control and Option Switches ..... 6

Self-Test Procedure ...... 20.6 cece ec eee ee ee ee een eee eee 7 Game Option Settings . . 9 Game Price Settings... .. 211 Coin Counter Option Settings . - 13 Opening the Control Panel and Replacing Switches - 16

Monitor Removal... 0... cc cece cece eee enter e eee eee es 7 Fluorescent Tube Replacement . . 18 Printed-Circuit Board Replacement Power Distribution Signal Distribution

Iiustrated Parts Lists: Cabinet-Mounted Assemblies .... Control Panel Assembly......... Fluorescent Light and Speaker Assembly Regulator/Audio | PCB Assembly Asteroids Deluxe™ Game PCB Assembly .........-.0.0 000s cece eee 30

Power Supply Assemblies for X-Y Games . American-Made Coin Door . . British-Made Coin Door

Page 6
NOTE If reading through this manual does not lead to solving a certain maintenance problem, call Tele-Help™ at the Atari Customer Service office in your geographical area, as shown in one of the two maps below. Order all parts from the California office.

WEST and CENTRAL U.S.A.

Parts for all Atari Customers. Sales and Service

Atari Coin-Op Customer Service 1105 N. Fair Oaks Avenue P. O. Box 427, Sunnyvale, CA 94086 Telex 17-1103

(Monday - Friday, 7:30 - 4:00 pm Pacific Time)

= From California, Alaska or Hawaii (408) 745-2900

From anywhere else in this area toll-free (800) 538-1611

EAST U.S.A.

Sales and Service Only

Atari Inc. New Jersey Customer Service Office Cottontail Lane, Somerset, NJ 08873 Telex 37-9347

(Monday - Friday, 7:30 - 4:00 pm Eastern time) rod From New Jersey (201) 469-5893

From anywhere else in this area toll-free (800) 526-3849

Page 7

Notice Regarding Non-Atari Parts

WARNING

Use of non-Atari parts or modifications of your Atari game circuitry may adversely affect the safety of your game, and may cause injury to you and your players.

Atari, Inc.’s warranty (printed on the inside back cover of this manual) may be voided, if you do any of the following:

1.) you substitute non-Atari parts in your coin-operated game, or

2.) you modify or alter any circuits in your Atari game by using kits or parts not supplied by Atari.

Not only may the use of any non-Atari parts void your warranty, but any such alteration may also adversely affect the safety of your game, and may cause injury to you and your players.

Page 8

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 9
WARNING — SHOCK HAZARD, Connect this game only to a grounded 3-wire outlet. If you have only a 2-wire outlet, we recommend you hire a licensed electrician to install a grounded outlet. Players may receive an electric shock if this game is not properly grounded!

A. New Parts

The Asteroids Deluxe™ game has two new parts. \f you have worked on Atari games in the past, then you should be aware of these important differences. The new parts are: @ Deep-Well Coin Box. This new coin box conservatively holds $600 in U.S. quarters. Please

note that $500 in quarters weighs over 11 kg (25 \bs.), and $600 in quarters weighs 12% to 13% kg (28-30 !bs.). @ Game PCB Circuitry. Most video games to date have used the raster-scan method of display. This game uses vector-generation with X and Y
Page 10

ATTRACTION PANEL

MONITOR SHIELD

ACCESS PANEL

XY a MONITOR

CONTROL 8 co

PANEL - eee

GAME PCB

»

REGULATOR! AUDIO PCB

COIN DOOR

POWER ONIOFF SWITCH

POWER SUPPLY

Figure 1 Overview of Game

Page 11

axes which allows better contrast and a greater number of moving objects, and draws lines at any angle. In addition, Asteroids Deluxe™ is one of the first Atari games to have non-volatile memory for part of the high score table. This means that even if power is removed from the game, the three highest scores wiil permanently stay in memory. You may erase these scores by following the instructions in Figure 6, Self-Test Procedure.

These new parts, as well as all other major parts in the game, are illustrated in Figure 1. Throughout this manual, wherever one of these new parts is

mentioned, you will see this symbol: “oO

B. Game Inspection

This new game is ready to play upon removal from the shipping carton. However, your careful inspection is needed to supply the final touch of quality control. Please follow these steps to help us insure that your new game was delivered to you in good condition.

[donot NOTE venti Do not plug the gam yet!

  • Examine the exterior of the game cabinet for dents, chips, or broken parts.
  • Uniock and open the access panel of the cabinet and inspect the interior of the game as follows: @ Check that al! plug-in connectors (on the game harness) are firmly seated. Replug any connectors found unplugged. DON’T FORCE CONNECTORS TOGETHER. The connectors are keyed so they only go on in the proper orientation. A reversed edge connector will damage a PCB and will void your warranty. @ Check that ali plug-in integrated circuits on the game PCB are firmly seated in their sockets.
WARNING To avoid possible unpleasant electrical shock, do not touch internal parts of the monitor with your hands or metal objects held in your hands! @ Note the location of the game's serial number—it is printed on the special label on the outside of the game cabinet. Verify that the serial numbers also stamped on the Asteroids Deluxe™ Game PCB, Regulator/Audio PCB and monitor are all identical. A drawing of the serial number locations is on the inside front cover of this manual. Please mention this number whenever you call your distributor for service.

@ Check all major subassemblies such as the power supply, control panel and monitor for secure mounting.

Cc. Game Installation

Figure 2 Installation Requirements

Power 175 watts Temperature 0° to 38°C (32° to 100°F) Humidity Not over 95% relative Space Required 64x 81% cm (25% x 32 in.) Game Height 182% cm (71% in.)

  • Line Voltage Selection This game has two possible power supplies: the U.S. or international power supply. The U.S. power supply operates on one line voitage range: 105 to 135 VAC. The international power supply has four colored voltage selection plugs and operates on the line voltage of almost any country in the world.

Before plugging in your game, check your power supply. If the supply doesn’t have voltage selection plugs and a connector at J3 (see Figure 3), then the game operates on any voltage from 105 to 135 VAC. If the supply has the colored voltage selection plugs, make sure that the voltage selection plug is correct for your location’s line voltage. Check the wire color on the plug and see if it is Correct per the list below.

Line Voltage Range Voltage Selection Plug Color

90-110 VAC (100) Violet 105-135 VAC (120) Yellow 200-240 VAC (220) — Blue 220-260 VAC (240) Brown

Page 12

Figure 3 International Line Voltage Selection

  • Interlock and Power On/Off Switches To minimize the hazard of electrical shock while working on the inside of the game cabinet, two interlock switches have been installed (see Figure 4). One is located behind the access panel and one is behind the coin door. These switches remove all AC line power from the game circuitry when a door is opened.

Check for proper operation of the interlock switches by performing the following steps: @ Plug the AC line power cord into an AC outlet. @ Close the access panel and coin door. @ Set the power on/off switch to the on position. Within 30 seconds the TV monitor should display a picture. Slowly open the access panel. The TV monitor picture should disappear when the panel is opened approximately 2.5 cm (1 inch). Close and lock the access panel and repeat this step with the coin door.

If the results of the preceding step are satisfactory, the interlock switches are operating properly. If the TV monitor doesn’t go off as described, check to see if the corresponding interiock switch is broken from its mounting or stuck in the on position.

Page 13

SAFETY INTERLOCK SWITCH

POWER ON/OFF SWITCH

Figure 4 Interlock and Power On/Off Switches

Page 14

“~

GAME PCB

BS Oe aa |

OPERATOR OPTION SWITCH

~ 8 % CO

VOLUME INCREASE:

SELF-TEST TURN CLOCKWISE

SWITCH | ws) | SELF-TEST SWITCH (EURO- PEAN GAMES) VOLUME CONTROL

Figure 5 Location of Self-Test Switch,

Volume Control and Option Switches

Page 15

D. Self-Test Procedure

This game will test itself and provide data to dem- Part of the self-test procedure includes a disonstrate that the game’s circuitry and controls are play of the operator-selectable game options. operating properly. The data is provided on the mon- Therefore, we suggest you run the self-test proceitor and the game speaker; no additional equipment dure in Figure 6 anytime you need to change the is necessary. game’s options.

Figure 6 Self-Test Procedure

Results if Instruction Test Passes Results if Test Fails

  • Set self-test The monitor displays RAM FAILURE is indicated by a sequence of low and high beeps. Note the sequence switch to on posi- the picture below. The of beeps and determine which RAM(s) may be bad. To restart the sequence, press the tion (see Figure 5). | game produces onlya _reset pushbutton on the game PCB, or set the self-test switch to off, then again to the very short beep on position. sound. Possibie Bad Sequence of Beeps RAM Chip Location(s) 1 low a 2 lows U1, M1 1 high. 1 low M1 2 highs, 1 low M3 2 highs, 2 lows M3, R3 3 highs, 1 low R3 4 highs, 1 low N3 4 highs, 2 lows N3, P3 5 highs, 1 low P3

Example only—detail on next page explains these four rows of symbols.

  • Activate ail 7 As you activate and control-panel switch: deactivate each es, the slam switch, ‘switch, you'll hear a and coin door short low beep. Both switches. start switch LEDs will be constantly lit.
  • Erasing the High Score Table (optional) Any bad RAMs must be repiaced before the self-test can continue.

ROM/PROM FAILURE is indicated by the display of the actual PROM or ROM chip location(s) on the center left side of the monitor screen. Both a PROM or its equivalent ROM are inserted into the same socket. Therefore, the displays are correct regardless of whether your game PCB has PROMs or ROMs or a combination of both. If the screen is blank or displays “garbage,” the chips at locations N2 analor J1 are probably bad.

INVERTING CIRCUITRY FAILURE is indicated by the BANK ERROR message in the lower center part of monitor screen. This circuitry is necessary for the cocktail-table version to function properly, that is, the picture turns 180° with every other ship in 2player cocktail games.

AUDIO CHIP FAILURE is indicated by the ERROR message at center bottom of the screen. The large audio chip is at location M7/8 on the game PCB.

You will not hear a short low beep for the defective switch, or dark LED.

The current three highest scores are held in permanent memory, even if the game is unpiugged. These three are marked with spaceship symbols in the high score table. If you want to erase these scores, simultaneously press the rotate left, rotate right, thrust, and fire buttons. The ERAS/NG message near the center of the screen will then be displayed for several seconds, until the entire table is erased.

  • When satisfied with test, set selftest switch to off position.

[Selt-test continued on next page]

Page 16

Figure 6 Self-Test Procedure, continued

Coin Bonus Adder 0, 5,6 or 7 = No bonus coins 1 = For every 2 coins* inserted, game logic adds 1 more coin* 2 = For every 4 coins* inserted, game logic adds 1 more coin* 3 = For every 4 coins” inserted, game logic adds 2 more coins* 4 = For every 5 coins* inserted, game logic adds 1 more coin*

Center Mech Multiplier

= Genter coin mech x 1 (Both these settings affect = Center coin mech x 2 the left mech in a 2mech door) {

Right Mech Multiplier 0 = Right coin mech x 1 1 = Right coin mech x 4 2 = Right coin mech x 5 3 = Right coin mech x 6

Game Price 0 = Free play 1 coin® for 2 plays 2 = 1coin* ford play 3 = 2coins” for 4 play

*In the U.S. a "coin" is defined as 25¢. In Germany a “coin” is 1 DM.

Game Lanugage 0 = English 1 = German 2 = French 3 = Spanish

Ships at Game Start 0 = Game starts with 2 to 4 ships Game starts with 3 to 5 ships Game starts with 4 to 6 ships Game starts with 5 to 7 ships (See graphic display in third line for exact number of ships)

Minimum Number of Plays Oor2 = 1-play minimum tor3 = 2-play minimum

Bonus Ship 0 = Bonus ship at every 10,000 points Bonus ship at every 12,000 points Bonus ship at every 15,000 points 3 = No bonus ship (adds 1'ship at game start)

, Graphic display of number of ships per game (up to 7)

| O la 0 ——— Point score at which a bonus ship is granted (blank if no bonus ship)

Page 17

E. Option Switch Settings

  • Bonus Play Feature Asteroids Deluxe™ offers a bonus play for certain combinations of coins inserted. This bonus feature is Operator-selectable, meaning you may choose to offer it or not.

For example, with your game set at 50¢ per play, players who deposit four successive quarters or a $1.00 coin, then press the start button, can receive a bonus play. Therefore, players can receive 3 plays for $1.00.

This bonus feature encourages players to insert more money than just the minimum 50¢ required for one game. Various other bonuses are also available (see Figure 8).

Figure 7 Game Option Settings

To change toggle positions on the switch assemblies, you need not remove the game PCB. The switches, usually colored blue, are easily accessible when the Asteroids Deluxe™ Game PCB is mounted in place. When changing the options, verify proper results on the Monitor display by performing the self-test. Note that changing an option on any of the following eight toggles wil! cause an immediate change on the monitor screen during the self-test.

Toggle Settings of 8-Toggle Switch on Asteroids Deluxe PCB (at RS—LEFT switch when PCB is in game) 8 7 6 5 4 3 2 1 Option

On On Off Off

On On On Off

Off On

Off Off pasn iON

Off On On On Off Off On. Off Off On English language $ Off German language On French language Off Spanish language Depending on settings of certain other switches... Game starts with 2 to 4 ships Game starts with 3to5 ships $ Game starts with 4 to 6 ships Game starts with 5 to 7 ships 1-play minimum $ 2-play minimum Bonus ship at every 10,000 points $ Bonus ship at every 12,000 points Bonus ship at every 15,000 points No bonus ship

$ Manufacturer's suggested settings

Page 18
  • Coin Mechanism Multipliers Available since early 1980, Atari’s coin door has either two or three mechanisms. All recent Atari game PCBs identify the different mechanisms in a certain pattern.

The right coin mechs are all the same to the game’s logic, regardless of whether you have two or three mechs in your door. In addition, the logic sees the left mech in a 2-mech door and the center mech in a 3-mech door as the same. Refer to the diagram below.

[ese [s1 [2se) |[2se} |[ $1 This pattern is important for you to know, so you can correctly set the “multipliers” for each mech. The multipliers determine how much each mechanism will be worth to the game's logic.

The basic unit of measurement is 25¢, which equals a multiplier of x 1. Therefore, if you have a 25¢/25¢/$1 coin door, you will probably want to set the center and right option-switch multipliers at x 1/x 4. (The left mech in a 3-mech door always has a value of x 1—you cannot change its value.)

You can set these multipliers with toggles 3 thru 5 on the Asteroids Deluxe™ Game PCB switch assembly at location L8. For exact settings of these toggles, refer to Figure 8.

  • Examples of Option Switch

Settings

Figure 8 explains the options, giving twelve examples of the most common U.: uations. The toggles mentioned are all in the ch at location L8; they only relate to game price, coin mechanism multipliers, and bonus play. You should set the toggles relating to other functions as you see fit, although Figure 7 provides “$” symbols indicating Atari’s recommendations.

Page 19

Figure 8 Game Price Settings The white block below contains Atari’s suggested settings. All numbers 1 thru 8 are toggle settings on the 8-toggle switch at location L8, on the Asteroids Deluxe™ game PCB (the CENTER switch assembly).

50¢ PER PLAY: Bonus $.50 = 1 play Bonus $.75 = 2 plays $1.00 = 3 plays 7 6 Off Off On Straight 25¢ Door

Off On Off

25¢ PER PLAY:

Bonus Bonus No bonus $50 = 3 plays $1.00 = 5 plays

Circled numbers refer to coin-door labels you Should use with each situation (labels are illustrated ‘on the following page).

Use the label no. 6 (indicated above with ©) only

if you set toggle 5 at PCB switch assembly R5 to off.

ah]

Page 20

Figure 8 Game Price Settings, continued For your information, we have defined below the switch settings for those options relating to game price, coin mechanism multipliers, and bonus play. This information is useful in case you need to temporarily set the Asteroids Deluxe™ game on free play, or if you have German coin mechanisms in your door. The label no. 6 shown below should be used only if you set toggle 5 at PCB switch assembly RS to off.

Toggle Settings of 8- Toggle Switch on Asteroids Deluxe

PCB (at L8—CENTER switch when PCB is in game)

8765432

Option

On On Off Off

On On On Off

Off On

Off Off

On Off

OnOnOff
OnOffOn

On Off Off Off On On

On Off On Off Free play 1 coin* for 2 plays 1 coin* for 1 play 2coins* for1 play $

Right coinmech x 1 $ Right coin mech x 4 Right coin mech x 5 Right coin mech x 6 Center coin mech x 1 $ (Both these settings affect Center coin mech x 2 the left mech in a 2-mech door) No bonus coins For every 2 coins” inserted, game logic adds 1 more coin* For every 4 coins* inserted, game logic adds 1 more coin* For every 4 coins* inserted, game logic adds 2 more coins* $ For every 5 coins* inserted, game logic adds 1 more coin*

“In the U.S., a “coin” is detined as 25%. In Germany a “coin” is 1DM.

$ Manufacturer's suggested settings To achieve bonus plays, all coins must be inserted before pressing start button.

C J, @@ 2 coins ATARI

ATARI @ 1 coin = 1 play

AO @@ 2 coins =1 play ATARI

6 ae @ 4 coins = 3 plays ne @@ 2coins = 1 play Am @@@ 3 coins = 2 plays @@@@ 4coins = 3 plays

° ee 2 coins = 1 play Ay @ $1 coin =3 plays (Susan B. Anthony coi

on @ 1coin = 1 play ame’ 2 play minimum (2 coins = 2 plays)

(For operator use—write in the appropriate phrase. Use a permanent-ink water-resistant marker.)

Page 21

Figure 9 Coin Counter Option Settings

[These toggles determine which coin mechanisms activate which counters]

Toggle Settings of 4-Toggle Switch on Game PCB (at M12) 4 3 2 1 For Games Having These Coin Doors: Option

OnOnThai 1 Baht/1 Baht, German 1 DM/1 DM, U.S. 25%/-All 3 coin mechanisms are

25¢, Belgian or French 5 Fi/5 Fr, Swiss or French same denomination; all 1 Frit Fr, U.S, 25¢/25¢/25¢, Japanese Y190/Y100, register on one coin Swedish 1 Kr/1 Kr, U.K. 10 P/10 P, Australian 20¢/- counter. $ 20¢, or Italian 100 L/100 L.

OffOnGerman 2 DM/1 DM, German 1 DM/5 DM, U.S. 25¢/-Left and center mechanisms

25¢/$1, or U.S, 25¢/$1. are same denomination; right mech is another denomination. Requires two coin counters.

OnOffNo coin door is currently designed for this contig-Left mech is one denomina-

uration. tion; center and right mech are another denomination. Requires two coin counters.

OffOffGerman 1 DM/2 DM/5 DM.Left, center and right mechs

are 3 different denominations. Requires three coin counters.

$ Manufacturer's suggested settings

F. Game Play

Atari’s Asteroids Deluxe™ is a one- or two-player game with an X-Y or vector-generator monitor. The game depicts a third-person view of a player's spaceship battling to destroy asteroids, flying saucers and enemy ships or “death stars” (shaped like clusters of triangles). When hit, the asteroids and death stars will break into progressively smaller pieces.

Players can put up an octagon-shaped “shield” to temporarily protect their spaceship. However, this shield wears out with use.

The game has five possible modes of operation: Attract, Ready-to-Play, Play, High Score Initial, and Self-Test. Self-test is a special mode for checking the game switches and computer functions. You may enter this mode at any time. When entered, all game credits are cancelled.

  • Attract Mode The attract mode begins when power is applied to the game, after a play or high score initia! mode, or after self-test. This mode is continuous and is only interrupted when a game is paid for and accepted or when you enter self-test.

In this mode, the monitor displays two possible pictures. One picture is of randomly tumbling asteroids, large and small saucers, and death stars—all in a simulated game. The other picture shows the ten currently highest scores.

If you erase the special “permanent” memory (see Figure 6, Self-Test Procedure), then the second picture with the high-score table will not appear on the screen. The table is redeveloped from scores of subsequent games.

Page 22
  • Ready-to-Play Mode This mode begins when sufficient coins have been accepted for a one- or two-player game. It ends when the 1 PLAYER START or 2 PLAYER START pushbutton is pressed.

Operators may choose one- or two-play minimums by selecting one of the option switch settings on the game PCB (see Figure 7, Game Option Settings). If you have selected the two-play minimum and a player has inserted enough money for only one play, the message 2 GAME MINIMUM and CREDITS ‘% will stay on the screen until the second coin has been inserted.

When this mode begins, the message PRESS START flashes immediately below the center score at the top of the screen. The displayed pictures are otherwise the same as those shown in the attract mode.

  • Play Mode The play mode begins when either start pushbutton is pressed. The mode ends when the player's last ship of the game is lost.

Six large asteroids appear and drift in from the outer edges of the display. By pressing the ROTATE LEFT and ROTATE RIGHT pushbuttons on the control panel, the player may aim a spaceship toward any of the asteroids. The player uses the FIRE pushbutton to shoot at the asteroids and other objects.

When shot, each large asteroid divides into two medium-sized asteroids, and the game adds 20 points to the player’s score. Medium-sized asteroids, when shot, divide into two small-sized astetoids, and the game awards 50 points to the player. When shot, the smallest asteroid disappears and the game adds 100 points to the player's score.

In addition to asteroids, the players can score points for shooting the various enemy ships. When hit, the large ships (‘death stars” shaped like hexagons) score 50 points and break into three diamond shapes. The medium-sized enemy or diamond, when hit, grants the player 100 points and breaks into two small triangular pieces. These small pieces disappear when the player hits them, and the score increases by 200 points.

At any time during game play, a flying saucer may appear from either side of the display. The game awards players 200 points for shooting a large saucer and 1000 points for a small saucer. (The latter is a smaller target for players, though not any faster moving than the large one. It also shoots more accurately.) The player's objective in the game is to shoot and destroy as many asteroids, saucers, and enemy ships as possible before all his or her spaceships are destroyed. A ship is destroyed if an asteroid, saucer or enemy ship smashes into it, or if a flying saucer shoots it. To prevent losing a ship, the player may press the THRUST pushbutton to move out of the path of an oncoming object.

As an emergency maneuver, a player can press

  • the SHIELDS pushbutton. An octagon will then appear around the player’s ship as protection from all enemies. For challenge the shield power lasts only about 10 seconds, but the power is renewed with each ship. The amount of shielding power available is shown by the brightness of the octagon (dim means almost exhausted power).

An operator option allows you to award an extra ship each-time a player’s score reaches multiples of 10,000, 12,000 or 15,000 points. As an alternative, you may not offer any bonus ships at all to players. Refer to Figure 7, Game Option Settings, for how to set your game for this option.

When the last ship of the game is destroyed, the message GAME OVER appears below the high score. This message remains for three seconds before the high score initial mode begins.

  • High Score Initial Mode At the beginning of the high score initial mode, the player instructions appear at the top of the screen, and A _____ appears at the lower center of the display. Players enter initials one character at a time.

By pressing the ROTATE LEFT pushbutton, the displayed character steps through the alphabet from A to Z. By pressing the ROTATE RIGHT pushbutton, the character shown will step backwards through the alphabet from A to a blank space, then from Z to A. Once the game displays the desired letter, players should press the SHIELDS pushbutton to record the letter; then an A appears in the next space.

If players need only two letters for their initials, they should use the blank between Z and A in one of the three locations. Pressing the SHIELDS pushbutton a third time will cause the initials and game score to be transferred to the high score table. This table contains a maximum of 10 scores and appears during the attract mode.

Page 23

Maintenance

Ail games require certain maintenance to keep them in good working order. Clean, properly maintained games will attract players and earn more profits.

The most important maintenance item is running the self-test every time you collect money from the cash box. Just looking at a game wil! not tell you if the light-emitting-diode (LED) switches or leaf switches are broken, or if LEDs have burned out. The self-test will inform you of any of these possible problems.

Second, you should regularly clean the outside of the game and the coin mechanisms. In addition, you will need to regularly clean the leaf switch contacts: for details see this chapter.

Page 24

A. Cleaning

The exterior of the game cabinet and the metal and acrylic surfaces may be cleaned with any nonabrasive household cleaner. If desired, special coin machine cleaners that leave no residue can be obtained from your distributor. Do not dry-wipe any of the acrylic panels, because any dust can scratch the surface and result in fogging the plastic.

B. Fuse Replacement

This game contains five fuses—all on the power supply assembly (not including the monitor fuses). Replace fuses only with the same type as listed in Figure 21 of this manual. See the Quadrascan™ monitor manual for the monitor fuse data.

NORMALLY CLOSED (N.C.) CONTACT

NORMALLY OPEN $0) CONTACT \ \ \. LIGHT-EMITTING-DIODE COMMON J (L-E.D) CONTACTS CONTACT

C. Opening the Control Panel

Prior to repairing or replacing any switch on the control panel or prior to removing the monitor, unplug the game. Then open the coin door.

Reach up through the opening and remove both sets of carriage bolts, wing nuts, split lock washers, and large flat washers, located on the underside of the control panel (see Figure 10).

Lift up on the control panel and tilt it towards you. Be sure that the acrylic monitor shield does not fall on you. The top edge of the control panel acts as a retainer strip for the shield: once the control panel is opened, the shield is free and could slide out under its own power.

To Remove LED Switch: @ Remove all wires from the faulty switch. Turn the switch counterclockwise while holding the black cone-shaped nut on the outside of the control panel. @ Install a new switch using the reverse procedure. @ Reconnect the hamess wires.

Figure 10 Opening the Control Panel and Replacing Switches

Page 25
  • LED Switch Replacement The light-emitting diode (LED) switches on the control panel have a very low failure rate. In case a switch should ever be suspect, first test it per the description that follows. To replace the switch, refer to Figure 10.

@ Remove the wires from the suspected switch. @ Set multimeter to ohms scale. Set ohms scale to Rx1, then zero the meter. @ Connect multimeter leads to appropriate LED switch contacts (see Figure 10 for designation of switch contacts and meter lead placement). @ Check contacts (push and release the switch button) for closed and open continuity. @ = If the contacts do not operate sharply or always remain closed or open, then replace the LED switch as outlined in the figure.

  • Leaf-Switch Replacement
NOTE Adjust switches for a narrow gap. When a switch button is depressed, the resulting wiping action of the contacts provides a self-cleaning feature.

All five of these leaf switches operate on 5 volts at a very low current. Therefore, pitting of these switches would be extremely rare. Probably the only reason that pitting would occur is in very highhumidity locations.

Don’t burnish the switches. Burnishing them removes their plating, thus increasing the corrosion of the contacts. The best method of cleaning the switch contacts is to wipe them with a non-abrasive surface. A business card works very well.

To replace any of the five leaf switches, remove both of its screws with a Phillips-head screwdriver— see Figure 10.

If the white button itself needs to be replaced, turn the stamped nut with a wrench in a counterclockwise direction, as seen from the inside of the control panel. The white ring on the outside of the control panel should not spin, due to its design.

D. Monitor

Removal

WARNING High voltages may exist in any television monitor, even with power disconnected. Use extreme caution and do not touch electrical parts of the yoke area with your hands or with metal objects in your hands! If you drop the monitor and it breaks, it will implode! Shattered glass and the yoke can fly 6 feet or more from the implosion. Use care when replacing any monitor.

If you should need to remove the Quadrascan X-Y monitor, follow steps 1 thru 4 as listed on this page. Refer to Figure 11.

  • Unplug the game from its wall outlet. Open the coin door. Reach in the opening and unpiug the 12-pin harness connector underneath the monitor.
  • Open the rear access panel. Unplug the harness connector located at the center left side of the access panel opening.
  • Locate the two brass-colored “L” brackets that fasten down the wood monitor shelf. Remove the two sets of carriage bolts, flat and split lock washers, and hex nuts that secure the monitor assembly to these brackets.
  • Carefully bend the bottom rear flap of the large background bezel compietely inward. (If the flap has tape on each end, cut thru the tape first.) Slide the monitor chassis out the rear of the game.

Disassemble in the order indicated. (Circled numbers match the steps above.)

Monitor Removal Figure 11

Page 26

E. Fluorescent Tube Keplace ment

Tube Keplace-

WARNING If you drop a fluorescent tube and it breaks, it will implode! Shattered glass can fly 6 feet or more from the implosion. Use care when replacing any fluorescent tube. Avoid looking at the blacklight when it is on. \t may damage your eyes.

To replace the fluorescent white- or blacklight tube behind the front graphics attraction panel, follow this procedure (see Figure 12):

  • Remove the three Allen-head screws and lock washers at the top of the game (they secure the black metal retainer for the attraction panel). Lift the attraction panel up and out of its lower retainer. If you need to replace the blacklight tube, remove the two Phillips screws that secure the light board to the cabinet, and slide out the . whole assembly. The harness has plenty of length, so you can pull the assembly about two feet out of the game. Remove the two Y-shaped connectors from the ends of the fluorescent tube: you may find it helpful to use a flat-head screwdriver. Now carefully remove the tube from its clamps by pulling it towards you. Replace with a new tube. Do not snap the tube in vigorously—you may break it, causing an implosion! Reconnect the Y-shaped connectors. Reinstall the fluorescent light assembly with the two screws (if you removed it). Replace the attraction panel on the front of the game. When tightening the Allen screws, be sure the top retainer strip is pushed tightly back against the attraction panel.

Figure 12 Fluorescent Tube Replacement

Page 27

REGULATOR! AUDIO | PCB

PCB

Figure 13 Printed-Circuit Board Replacement

F. Printed-Circuit Board Keplace ment

Board Keplace-

You may wish to remove the Asteroids Deluxe™ game PCB or the Regulator/Audio | PCB for service or inspection. To do this, refer to Figure 13 and proceed as follows:

  • Game PCB Removal @ Unlock and open the access panel. @ Remove the two beaded nylon tie wraps from the PCB’s edge connector. Remove the 44-pin edge connector from the right side of the PCB. @ Locate the Phillips-head screw that extends through the PCB and into the wood block (at the right side of the board). Remove and save this screw as well as the fiber washer. ®@ Remove the PCB from the cabinet by carefully pulling it out of the plastic PCB retainer. After servicing it, reinstall the PCB, making sure that the 44-pin edge connector is properly plugged in. Note that the connector is keyed to fit on only one way, so if it doesn’t slip on easily, don’t force it! A reversed connector will probably damage your game and will void the warranty. Check that the operation of the game is correct by performing the self-test. This is especially
important with any game when you replace a PCB.

Regulator/Audio | PCB Removal Unlock and open the access panel. Remove the five plug-in connectors on the Regulator/Audio | PCB. Note that all of these connectors are keyed for proper orientation. Locate the two Phillips-head screws that extend through the PCB and into the wood behind the PCB. Remove and save these two screws and the two fiber washers. Remove the PCB from the interior wall of the cabinet.

Page 28

G. Game Operation

With this manual you received two large sheets that contain the wiring and schematic diagrams for the Asteroids Deluxe™ game. Sheet 1, Side A, includes information that shows the arrangement of these diagrams. These diagrams include information that explains the functions of the circuits and defines inputs and outputs.

Atari’s Asteroids Deluxe is a microprocessorcontrolled game. The microprocessor is contained on the game PCB. The game PCB receives switch in- Puts from the control panel and coin door. These inputs are processed by the game PCB and output to the monitor, Regulator/Audio | PCB, and control panel.

The monitor is an X-Y monitor. Therefore, the monitor receives signals for the X, Y and Z axes. Since the location of the beam in the monitor is totally controlled by the X- and Y-axis outputs of the game PCB, the game PCB does not contain a standard sync circuit. The X- and Y-axis inputs to the monitor step in increments of 1024 steps for the X (horizontal) axis, and 768 steps for the Y (vertical) axis. The Z axis merely controls the intensity of the beam.

The Regulator/Audio | PCB performs two functions: 1) it regulates the + 10.3 VDC from the power supply to +5 VDC, and 2) it amplifies the audio output from the game PCB. The +5 VDC from the Regulator/Audio | PCB provides most logic power to the game PCB. The audio output from the Regujator/Audio | PCB directly drives the game speaker and is controlled by the volume control, mounted inside the coin door.

The Power Supply is the source of all voltages in the game. These voltages are protected by four fuses in the fuse block on the power supply chassis. The primary winding of the power supply transformer is protected by the cartridge-type fuse in the power supply chassis.

Figure 14 illustrates the distribution of power in this game. Figure 15 illustrates the distribution of signals.

Page 29

FLUORESCENT LIGHTS

MONITOR

POWER INTERLOCK SWITCHES

COIN DOOR

‘GAME PCB

g} 8 a] 3

gl S| a] REGULATORIAUDIO | PCB: Sa

AC POWER CORD

POWER oH ONIOFF SWITCH A \ POWER SUPPLY we

Figure 14 Power Distribution

Page 30

CONTROL PANEL MONITOR

VOLUME CONTROL

COIN DOOR

REGULATOR/AUDIO | PCB:

Figure 15 Signal Distribution

Page 31

ustrated

Parts Lists

This chapter provides you with the necessary information for ordering replacement parts for your Asteroids Deluxe™ game. Please note that, for sim- Plicity, common hardware has been deleted from most of these parts lists. This includes screws, nuts, washers, bolts, etc.

The parts lists are arranged in alphanumeric order. For example, all “A-” prefix numbers come first. Following this are numbers in sequence evaluated up to the hyphen, namely 00- thru 99-, then 000598- thru approximately 190000-.

When ordering parts from your distributor, give the part number, part name, applicable figure number of this manual, and serial number of your game. This will help to avoid confusion and mistakes in your order. We hope the results will be less downtime and more profit from your game.

Page 32

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the Specific written permission of Atari inc., Sunnyvale, CA. This drawing is only conditionally issued, and neither receipt nor possession thereof confers or transiars any right in, or license to use, the sublect matter of the drawing of any design or technical information shown thereon, ner any right to reproduce this crawing or any part thereof. Except for manufacture by vendors of Atari, Inc, and for manufacture under the corporation's written license, no right to reproduce this drawing is granted or the subject matier thereof unless by writien agreement with or written permission from the corporation. Fluor. Lt. & Speaker Assy.— see Figure 18 036615-01 (Attract. Panel)

02-305010 (T-Moiding)

036498.01 (Attract. Retainer) 036617-03, -04, 05 036617-02 (3 Cardbd. Inserts) (Background Bezel) 036614-01 (Mon. Shield) 036617-01 (Mon. Bezel) 036495-01 03649901 (Sokr. Gill) A , (Mirror) (Monitor Assy.) 03631701 ; (Mirror Retainer) A036692.01 Ss . sang (Interconnect Harness) Fe SN 036316-01 — 002728-01 (Monitor Bracket) = (Ctrl-Panet Brkt.) Control-Panel Assembly — see Figure 17 036262-01

49.9092.(Coin Box Brkt)amt4-034536-03
(Vol. ControtA035943-01, -02, 03(Vibration Damper)
01(Deep-Well Coin Box)03574502
(Pricing Labels)03594201(PCB Retainer)

(Separator) 75-07017 036617-06 (PCB Spacer) (Coin Detlector) A036189-01 |. i (Interl. Sw. Assy.) 78-24012 007882.02 OB Tie Wap) (interl. Sw. Cover) (Pee Tie Wap American-Made Coin Door— e PGB Asey.— see Figure 22 so Faure 20 A036689-01 British-Made Coin Door— see Figure 23 (Main Harness) Regul/Audio | PCB— see Figure 19 034536-02 (Vibration Damper) 00999201 wa val (On/Off Sw. Cover) Power Supply Assy.—

Schematics, Self-Tesi Label & Manuals—78-3201see Figure 21A034841-05,

see parts list on opposite page 4 (Cabinet Leg) ‘A034631-01 A034863-05 (On/O't Sw. Assy.) (Power Cord)

Figure 16 Cabinet-Mounted Assemblies A036500-xx B

Page 33

Figure 16 Cabinet-Mounted Assemblies Parts List

Part No. Description

A034631-01 On/Off Switch Assembly

A034841-05Strain Relief Power Cord(U.S)
A034863-05Strain Relief Power Cord(German)Pa Neu)

A035943-01 Deep-Well Coin Box Assembly (for a// the same coins) A035943-02 Deep-Well Coin Box Assembly (for two different coin denominations—has one separator) A035943-03. Deep-Well Coin Box Assembly (for three different coin denominations—has two separators)

A036189-01(Interlock Switch Assembly(modified for safety)

A036606-01 Monitor Assembly (monitor itself is part no. 92-047 for Electrohome or 92-050 for Wells-Gardner; wood monitor shelf is part no. 036489-01) A036689-01 Main Harness Assembly (a/so includes on/off switch, 2 interlock switches and their brackets, and volume control and its bracket) A036692-01 Interconnect Harness Assembly (in upper rear part of game) The following six items are the technical information supplements to this manual: DP-165-01 Asteroids Deluxe™ Schematic Drawings (Sheet 1) DP-165-02 Asteroids Deluxe Schematic Drawings (Sheet 2) ST-165 Label with Self-Test Procedure and Option Switch Settings TM-151 Instruction and Service Manual for Electrohome G05-802/805 Quadrascan™ X-Y Monitor, OR TM-164 Service Manual for Wells-Gardner Quadrascan X-Y Monitor TM-165, Asteroids Deluxe Operation, Maintenance and Service Manual 02-305010 ¥s-Inch Plastic T-Molding 19-9032 Volume Control 71-2110 Panel Cartridge Lock Mechanism (for access panel) 75-07017 Spacer for Mounting Printed Circuit Boards 78-3201 Cabinet-Leveling Leg 78-24012 5-Inch Beaded Nylon Tie Wrap (for PCB Edge Connector) 002728-01 Control-Panel Mounting Bracket 00788202 Interlock Switch Cover 009992-01 On/Off Switch Cover 034536-02 Foam Vibration Damper (for Regu/ator/Audio | PCB) 034536-03 Foam Vibration Damper (for Game PCB) 035745-02 18-Inch Plastic PCB Retainer 035942-01 Deep-Well Coin Box Separator 036262-01 Coin Box Bracket 036316-01 Monitor Mounting “L” Bracket 036317-01 Mirror Retainer 036495-01 Speaker Grille 036498-01 Attraction-Panel Retainer 036499-01 Half-Silvered Mirror 036614-01 Monitor Shield with Graphics 036615-01 Attraction Panel with Graphics 036617-01 Cardboard Monitor Bezel with Blue Acetate Window 036617-02 Cardboard Background Bezel 036617-03 Cardboard Starship Insert 036617-04 Cardboard Asteroids Insert for Center (five asteroids) 036617-05 Cardboard Asteroids Insert for Side (four asteroids) 036617-06 Cardboard Coin Deflector 036686-01 Card of Coin-Door Pricing Labels

Page 34

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction’ forbidden without tne specific written permission of Atari, Inc., Sunnyvaie, CA. ‘This drawing is only conditionally Issued, and neither receipt nor possession thereof confers or transfers any right in, or license to use, the subiect matter of the draw: ng or any design or technical information shown thereon, hor any right tO reproduce this drawing or any part there” of. Except for manufacture by vendors of Atari, Inc., and for manufacture under the corporation's written license, ‘no right to reproduce this drawing is granted or the sub- Ject matter thereof unless by written agreement with or written permission from the corporation. 78-6900402 (Foam Tape)

A036616-01 (Control Panel)

036046-01 (Pushotn. Assy.)

033127-01 (Sw. Bushing)

62-039 (LED Switch)

160001-001 (Leaf Sw/ Button Holder)

75:9910NO

A036690-01 (Cirl-Panel Harness)

Figure 17 Control Panel Assembly A036611-01 A

Parts List

Part No. Description

A036046-01 Pushbutton Assembly A036690-01 Contre! Panel Harness Assembly 62-039 Momentary-Contact SPDT Light-Emitting Diode Switch 75-9910NO 5/8"-11 Steel Stamped Nut

78-6900402 Vinyl Foam Single-Coated-Adhesive Tape, 1/8-Inch thick x ¥4-Inch wide 033127-01 Black Molded Switch Bushing A036616-01 Control Panel with Graphics 160001-001 Leaf Switch and Button Holder (Leaf Switch only is part no. 160004-001)

Page 35

A005493-01 (Fl. Lt. Harness) 79-561816P_ (Wire Nut) 70-306, (Black Tube) 99-11012 48-009 (Bin. Spkr.) (1-In. Clamp)

99-1103: (Starter) 99-1109 (Socket)

99-11008 (Transtormer)

A036691.01 (Fl, Lt. & Spkr. Harness)

70-304: (White Tube)

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden withcut the specific written permission of Atari, Inc., Sunnyvale, CA, This drawing is only conditionally’ issued, and neither receipt nor possession thereo! confers or transfers any right In, or license to use, the subject matter of the draw. 99-11011 ing or any design or technical information shown thereon, ve nor any vfight to reproduce this drawing or any part (1 %-In. Clamp) thereof, Except for manufacture by vendors of Atari, Inc., and for mantiacture unger ‘he. corporation's “writen license, no right to reproduce this drawing is granted or 035835-01 or the subject matter thereot untess by written agreement A036045-01 with or written permission from the corporation. (Connector)

Figure 18 Fluorescent Light and Speaker Assembly A036610-01 A

Parts List

Part No. Description

A005493-01 Fluorescent Light Harness A036691-01 Fluorescent Light and Speaker Harness 48-009 8-Inch High-Fidelity Speaker 70-304 18-Inch 15-Watt Cool White Fluorescent Tube 70-306 18-Inch 15-Watt Blacklight Fluorescent Tube

79-561816P Spring Connector Wire Nut for 16- to 18-Guage Wires 99-11003 Fluorescent Lamp Starter 99-11008 Ballast Transformer 99-11009 Starter Socket 99-11011 1¥2-Inch Clamp (for white tube)

99-11012 1-Inch Clamp (for blacklight tube) 035835-01 Y-Lead Connector (part no. A036045-01 is an acceptable substitute)

Page 36

Asteroids Detuxe™

This drawing is only condit

passession thereat confers or transfers any

, oF license to u: subject mattor of the draw:

s DY wi

jen permission from the corpor

ons | 410.300 470UF fo) cl

9] ze c4 ce } “70 “9 o)

aio oo ab a7 ee - S&P {0} pore cis

“7, Aven ir—t|

= GND LL t

A A034485-03 Figure 19 Regulator/Audio | PCB Assembly

Page 37

Figure 19 Regulator/Audio | PCB Assembly Parts List

Part No. Description (Reference Designations and Locations in Bold)

12-52P72.7 Ohm, + 5%, 1W Resistor(R5)

19-100P1015 .1 Ohm, + 3%, 7W Wirewound Resistor (R24) 19-315102 1K Ohm Vertical PCB-Mounting Cermet Trimpot (R8) 24-250108 1000 uf Aluminum Electrolytic Fixed AxialLead 25V Capacitor (C13) 24-250477 470 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (C1, 4, 12) 24-350338 3300 ut Aluminum Electrolytic Fixed Axial-Lead 35V Capacitor (C9, 10) 29-088, .1 uf Ceramic-Disc 25V Radial-Lead Capacitor (C3, C11) 31-1N4002 100V 1-Amp. Silicon Rectifier 1N4002 Diode (CR1, 4) 33-TIP32 PNP Power Transistor, Type TIP32 (Q2) 34-2N3055, NPN Silicon Transistor, Type 2N3055 (Q3)

37-LM305,5V Linear Voltage Regulator(Q1)

75-F60405 #6-32 x 4 Inch Binder-Head Nylon Screw 78-16008 Thermally Conductive Compound for the 2N3055 78-16014 Thermally Conductive Compound for the TIP32

79-58306,6-Position Connector Receptacle(J6)
79-8308,9-Position Connector Receptacle(J7)

79-58354 4-Position Square Connector Receptacle (J8) 020670-01 Test Point 034531-01 Heat Sink 100015-103 .01 uf Ceramic-Disc 25V Radial-Lead Capacitor (C5, 14) 110000-010 1 Ohm, + 5%, %W Resistor (R10, 19) 110000-100 10 Ohm, + 5%, %W Resistor (R11, 20, 25, 26) 110000-101 100 Ohm, + 5%, %4W Resistor (R4, 12, 22) 110000-102 1K Ohm, + 5%, %4W Resistor (R15, 16)

110000-10310K Ohm, + 5%, ¥4W Resistor(R13, 14)
110000-271270 Ohm, + 5%, %4W Resistor(R1)

110000-330 33 Ohm, + 5%, %4W Resistor (R3)

110000-3923.9K Ohm, + 5%, %4W Resistor(R6)

110000-752 7.5K Ohm, +5%, “W Resistor (R7)

110001-221220 Ohm, + 5%, ¥zW Resistor(R9, 21)

122002-102 .001 uf Ceramic-Disc 25V Radial-Lead Capacitor (C2, 7, 16) 122004-224 .22 uf Ceramic-Disc 25V Radial-Lead Capacitor (C6, 8, 15, 17) 137151-002 8W Linear Audio Amplifier Integrated Circuit (Q5, 7)

Page 38

IAL: Reproduction forbidden without the

Inc., Sunn} A. own thereon, ‘or any part

agreement

fn permission from the corporation. oe | ' a, 2 Bo,

a Q ! | Sep Fi SAB gunk) lity ee ee

it ae) PR pe 15273 9 omy ary Tar} Pe (a

= = =z Pa [lef = BE fee ge es ee coal ER ere) 4 a on 2 4 6 8 10

A Figure 20 Asteroids Deluxe™ Game PCB Assembly A036471-01 and -02

Page 39

oe~ Figure 20 Asteroids Deluxe™ Game PCB Assembly Parts List

Part No. Description (Reference Designations and Locations in Bold)

C012294-01 Audio /0 N-Channel MOS/LSI Custom Chip (M7/8) 19-007 10K Ohm, + 20%, 1%W 8-Pin Dual-Inline-Package Resistor Network (RP1, RP2—use only if board has 74LS170s or 74LS670s at locations F3, H3, J3) 19-315103 10K Ohm Vertical PCB-Mounting Cermet Trimpot (R149, 152) 21-101104 .1 uf, + 10%, Radial-Lead Epoxy-Dipped 100V Mylar Capacitor (C118-120) 21-101153 .015 uf, + 10%, Radial-Lead Epoxy-Dipped 100V Mylar Capacitor (C30)

24-25010610 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor(C121, 122)
24-250107100 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor(C17)
24-25022622 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor(C104)

24-250477 470 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (C72, 73)

24-5001051 uf Aluminum Electrolytic Fixed Axial-Lead 50V Capacitor(C22, 49, 50, 74, 83, 85, 103)
28-10110010 pi Epoxy-Dipped 100V Radial-Lead Mica Capacitor(C87, 95)
28-101101100 pf Epoxy-Dipped 100V Radial-Lead Mica Capacitor(C77)
28-101100220 pf Epoxy-Dipped 100V Radial-Lead Mica Capacitor(C88, 89, 109, 110)
28-101271270 pf Epoxy-Dipped 100V Radial-Lead Mica Capacitor(C46)
28-101391390 pf Epoxy-Dipped 100V Radial-Lead Mica Capacitor(C75)
28-10168068 pf Epoxy-Dipped 100V Radial-Lead Mica Capacitor(C106, 111)
29-0061 uf, +10%, 35V Tantalum Capacitor(C21, 51, 116)

29-088 .1 uf Ceramic-Disc 25V Radial-Lead Capacitor (C1-16, 18-20, 23-29, 31-44, 47, 48, 52-71, 76, 78, 79, 81, 84, 86, 90:94, 96-102, 105, 107, 108, 112-115, 117) 31-1N100 100V Type 1N100 Germanium Switching Diode (CR3, 4, 11)

31-1N91475V Type 1N914 Silicon Switching Diode(CR1, 5)
31-1N400150V Type 1N4001 Silicon Rectifier Diode(CR7-10)
32-1N756A8.2V, +5%, Type 1N756A Zener Diode(CR6, 12)
33-2N3906,Type 2N3906 PNP Switching and Amplifying Transistor(Q1, 4, 5, 11-13)

34-2N3904 Type 2N3904 NPN 60V 1-Watt Transistor (Q2, 3) 34-2N6044 Type 2N6044 NPN Darlington Transistor (Q8-10) 34-MPSA06S Type MPSAO6S NPN 80V 500ma Transistor (Q6, 7)

37-LM324Type LM324 Integrated Circuit(P11)
37-TLO82CPType TLO82CP Integrated Circuit(A12, C12)

37-4016B Type 4016B Integrated Circuit (R11, B12, D12)

37-565Type 555 Timer Integrated Circuit(N11)
37-74LS00Type 74LS00 Integrated Circuit(C5, N4)
37-74LS02Type 74LS02 Integrated Circuit(D5, P10. Also, for -02 PCB assy. only: C7)
37-74LS04Type 74LS04 Integrated Circuit(L4, R9)
37-74LS08Type 74LS08 Integrated Circuit(E5, K5, R6, B8)
37-74LS10Type 74LS10 Integrated Circuit(A8, N8)
37-74LS14Type 74LS14 Integrated Circuit(B5)
37-74LS20Type 74LS20 Integrated Circuit(E4)
37-74LS32Type 74LS32 Integrated Circuit(M4, N5, B9)
37-74LS42Type 74LS42 Integrated Circuit(L5, E6, E8)
37-74LS74Type 74LS74 Integrated Circuit(D3, A6, R7)
37-74LS83,Type 74LS83 Integrated Circuit(M5)
37-74LS86Type 74LS86 Integrated Circuit(P4)
37-74LS109Type 74LS109 Integrated Circuit(A9)
37-74LS139Type 74LS139 Integrated Circuit(L2, E3)

[Continued on next page]

Page 40

Asteroids Deiuxe™

Figure 20 Asteroids Deluxe™ Game PCB Assembly, continued Parts List

Part No. Description (Reference Designations and Locations in Bold)

37-74LS157Type 741.S157 Integrated Circuit(F2, H2, J2, K2, F5, A10, B/C10, C10, D/E10, E10, F/H10)
37-74LS161Type 74LS161 Integrated Circuit(D6)
37-74LS 164Type 74LS164 Integrated Circuit(P8, R8, K9)
37-74LS174Type 74LS174 Integrated Circuit(P6, D8, F10, N10)
37-74LS175,Type 74LS175 integrated Circuit(M6, P9)
37-74LS191Type 74LS191 Integrated Circuit(K4, C9, D9, E9, F9, H9, J9)
37-74L5193Type 74LS193 Integrated Circuit(F4, H4, J4)
37-74LS244Type 74LS244 integrated Circuit(B1, C1, M9)
37-74LS245Type 74LS245 Integrated Circuit(P1,E2) Acceptable substitute is part no. 37-8304B

37-74L8251 Type 74LS251 Integrated Circuit (J10, £10)

37-74LS253.Type 74LS253 Integrated Circuit(P5)
37-74LS259Type 74LS259 Integrated Circuit(M10)
37-74LS273Type 74LS273 Integrated Circuit(F6, H6, J6, K6)
37-74LS367Type 74LS367 Integrated Circuit(H5, J5)
37-74LS393Type 74LS393 Integrated Circuit(B3, D4)
37-74LS374Type 74LS374 Integrated Circuit(L9,810,D10) Acceptable substitute is part no. 37-74LS273
37-74LS670Type 74LS670 Integrated Circuit(F3, H3,J3) Acceptable substitute is part no. 37-74LS170
37-7404Type 7404 Integrated Circuit(B4, H10)
37-7406Type 7406 Integrated Circuit(N6)
37-7497Type 7497 Integrated Circuit(For -01 PCB assy. only: F8, H8, J8, K8)
37-7805+5V Voltage Regulator(VR3)
97-7812+12V Voltage Regulator(VR1)

37-7815 + 15V Voltage Regulator (VR4)

37-7915— 15V Voltage Regulator(VR2)
37-9316Type 9316 Integrated Circuit(C3, C4, B6, C6, P7)

38-MV5053 Type MV5053 Light-Emitting Diode (CR2)

41-3004100 uH, + 10%, Hot-Molded Plastic Fixed R.F. Choke(L1, 2)

62-001 SPST Momentary Pushbutton Switch (A5)

66-114P1T4-Station Single-Throw, Dual-Inline-Package Bit Switch(M12)
66-118P1T8Station Single-Throw, Dual-Inline-Package Bit Switch(R5, L8)

79-42C24 24-Contact Medium-insertion-Force Integrated Circuit Socket (D1, E/F1, H1, J1, N/P2, R2) 79-42C40 40-Contact Medium-Insertion-Force Integrated Circuit Socket (C2, M7/8) 81-4302 Nylon Snap-In Fastener (VR1-4, Q8-10)

90-10212.086 MHz, + .005%, Crysial(Y1)

90-6013 Microprocessor (C2) 90-7033 Random-Access Memory (L1, M1, M3, N3, P3, R3) 020670-01 Test Point 034602-01 Programmable Read-Only Memory (C8) 035904-01 Type 828131 Integrated Circuit (For -02 PCB assy. only: F7, H7, J7) 035905-01 Type 828131 Integrated Circuit (For -02 PCB assy. only: E7) 036430-01 Read-Only Memory (D1) 036431-01 Read-Only Memory (E/F1) 03643201 Read-Only Memory (H1) 036433-01 Read-Only Memory (J1)

Page 41

Figure 20 Asteroids Deluxe™ Game PCB Assembly, continued Parts List

Part No. Description (Reference Designations and Locations in Bold)

036799-01 Read-Only Memory (N/P2) 036800-01 Read-Only Memory (R2) 100015-103 -1 uf Ceramic-Disc 25V Radial-Lead Capacitor (C45, 80, 82) 110000-102 1K Ohm, +5%, %W Resistor (R27, 29, 45, 47, 72)

110000-10310K Ohm, +5%, %4W Resistor(R9-26, 28, 33, 34, 39, 48-55, 67, 73, 74, 81-84, 86, 90, 92, 98, 102,

114, 117, 120, 121, 156, 159)

110000-104100K Ohm, +5%, %4W Resistor(R69, 80, 146)
110000-121120 Ohm, +5%, %W Resistor(R93, 126)

110000-122 1.2K Ohm, +5%, %4W Resistor (R36, 160)

110000-12312K Ohm, +5%, YW Resistor(R44)
110000-151150 Ohm, +5%, %4W Resistor(R68)
110000-18318K Ohm, +5%, %W Resistor(R75, 143)

110000-222 2.2K Ohm, +5%, YW Resistor (R37, 46, 76, 116, 118, 122, 125, 145, 154) 110000-223 22K Ohm, +5%, %W Resistor (R1-8, 35, 42)

110000-27027 Ohm, +5%, %4W Resistor(R71)
110000-271270 Ohm, +5%, %W Resistor(R88, 142)

110000-274 270K Ohm, +5%, YW Resistor (R157) 110000-331 330 Ohm, +5%, %sW Resistor (R30, 31, 115)

410000-3323.3K Ohm, +5%, %4W Resistor(R78, 147, 158)
110000-3923.9K Ohm, +5%, %W Resistor(R40, 94-96, 148, 151)

110000-471 470 Ohm, +5%, %4W Resistor (R32, 97, 99-101, 103-111, 127-139)

110000-4724.7K Ohm, +5%, %W Resistor(R38, 79, 85, 89, 91, 112, 123, 144. Also, for -02 PCB assy. only:

R56-66)

110000-47347K Ohm, +5%, ¥4W Resistor(R43, 87, 155)

110000-562 5.6K Ohm, +5%, v4W Resistor (R41) 110000-563 56K Ohm, +5%, %W Resistor (R77, 113) 110000-680 68 Ohm, +5%, %4W Resistor (R70) 110000-682 6.8K Ohm, +5%, YW Resistor (R150, 153, 161)

110000-8228.2K Ohm, + 5%, Y4W Resistor(R119, 124)

137108-001 Operational Amplifier Integrated Circuit (B/C12, E12) 137158-002 Type AM6012ADC Digital-to-Analog Converter (A/B11, C/D11) Acceptable substitute is part no. 37-AD561J (B11, D11) 137161-001 Electrically Alterable Read-Only Memory (N9)

Page 42

03448202 79-4411001 034544-01 036304-01

A035888-01 or -02

A036354-01 or -02 (U.S)

TOP VIEW

(F2 is not used)

NOTICE in PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the 78-70501SC specific written pecmission of Atari, Inc., Sunnyvale, CA. This drawing is on'y conditionally issued, and reither 29-053 receipt nor possessicn thereof confers or transfers any right in, or license to use, the subject matter of the draw: ing or any design of techrical information shown thereon, nor any right lo reproduce this Grawing or any part thereof, Except fer manufacture by vendors of Atarl, Inc. and for manufacture under the corporation's written license, no right to reproduce this drawing is granted or the subject matter Ihereof unless by written agreement with or written permission from the corporation,

BOTTOM VIEW

3A-MDA3501

A035890-01 (Int'l) A034630-01 or A036355-01 (U.S.) A034629-01 79-15021001

Figure 21_ Power Suppiy Assemblies for X-Y Games A035892-01 (International) A { A036353-01 (U.S.) A

Page 43

Figure 21 Power Supply Assemblies for X-Y Games Parts List

Part No. Description (Reference Designations in Bold)

A034629-01 A.C. Harness Assembly A034630-01 RFI Filter Assembly (FL1) A035674-01 Voltage Plug Assembly (set of four plugs—for international power supply only) A035888-01 or -02 Transformer Assembly—international only (T1) A035890-01 Power Harness Assembly (international only) A035891-01 Fuse Harness Assembly A036354-01 or -02 Transformer Assembly—U.S. only (T1) A036355-01 Power Harness Assembly (U.S. only) 29-053, 26,000 uf 15 VDC Electrolytic Capacitor (C1) 3A-MDA3501 Bridge Rectifier, Type MDA 3501 (CR1) 46-2014001 4-Amp. 125 V 3AG Slow-Blow Glass Cartridge-Type Fuse (F4, F5, F6) 46-2017002 7-Amp. 250 V 3AG Slow-Blow Glass Cartridge-Type Fuse (F1) 46-302202 20-Amp. 250 V 3AB Slow-Blow Ceramic Cartridge-Type Fuse (F3) 78-2708 Nylon Type 6/6 Hole Bushing with 5/8-Inch Inside Diameter x 55/64-Inch Outside Diameter x Y-Inch Thick 78-70501SC 2-Inch Diameter Capacitor Mounting Bracket 79-15021001 2-Circuit Single-Row Terminal Block 79-3206 §-Position 3AG Fuse Block with %4-Inch Quick-Disconnect Terminals 79-4411001 Panel-Mounting Non-Indicating 3AG Cartridge-Type Fuse Post 034482-02 Power Supply Chassis 034544-01 Fuse Block Cover 036304-01 Label for Fuse Values

Page 44

NOTICE TO ALL PERSONS RECEIVING THIS ORAWING CONFIDENTIAL: Reproduction’ forbidd. Specific written permission of Atari, Inc. . This drawing is only conditionally’ issued, and neither receipt nor possession thereof confers or transfers any Fight in, or license to use, the subject matter of the draw- Ing or any design or technical information shown thereon, nor any ‘right to reproduce this drawing or any part thereof. Except for manufacture by vendors of Atari, Inc., and for manufacture under the corporation's written license, no right to reproduce this drawing is granted or the subject matter thereof unless by written agreement with or written permission from the corporation. 99-10071

70-11-47

99-10080

72-9406S,

COIN MECHANISM. SEE PARTS LIST (71-12000)

99-0102 72-9803S COIN RETURN) — 99-1065 SWITCH WIRE CHUTE 99-10068 _/ SEE PARTS LIST Be-10047 (90-10075 thru ay waooe COIN switcH aséy, | 910078) PART OF 99-10047 ‘SEE PARTS LIST 99-1008 99-1082 (99-10042 thru 75-14128 99-1045) Figure 22 American-Made Coin Door 71-10xxxx D

Page 45

COIN RETURN BUTTON ASSY.— SEE PARTS LIST (99-10012 thru 99-1022, and 99-10107)

COIN DOOR ONLY— SEE PARTS LIST {99-10008 and 10010)

99-10094

99-10049

75-5520B

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific written permission of Atari, Inc., Sunnyvaie, CA. This diawing 's only conditionally issued, and neither receipt nor possession thereot ‘confers or transters any right in, or license to use, the subject matter of the drawing or any design af tecrnical imformation shown thereon, nor any right 10 reproduce this drawing or ary part thereol, Except for manufacture by vendors of Atari Inc. ‘and for manufacture under the corporation's writ: ten license, no right to reproduce this arawing is Granted or the subject matter thereof unless by Written agreement with or written permission from the corporation.

71-102201 — U.S. 25¢/28¢ Coin Door 71-103202 — U.S. 25¢/25¢/25¢ Coin Door 74-103203 — U.S. 254/25¢/$1 Coin Door 71102204 — German 2 DM/1 DM Coin Door 71-103205 — German 1/25 DM Coin Door COIN RETURN BUTTON COVER— ‘SEE PARTS LIST (99-10055 thru 99-10059)

PRICE PLATE— SEE PARTS LIST (99-10070, 99-10083 thru 99-10092, and 99-10108)

99-10062

75-9158 |

99-10051

71-102208 — German 1 DM/5 DM Coin Door 71102207 — Belgian 5 FriS Fr Coin Door 71-102208 — Swiss 1 Fri1 Fr Coin Door 11-102209 — Japanese 100Y/100Y Coin Door 74102210 — British 10 P/10 P Coin Door 99-10074

72-JA1405B

72-HA1404C

99-10061

72-JA1405B

74-102211 — Australian 20¢/20¢ Coin Door 71402212 — Italian 100 L/100 1. Coin Door 71-102213 — U.S. 50¢/50¢ (2 x 25%) Coin Door 71-103214 — U.S. 50%/50C/50¢ Coin Door 74-103215 — U.S. 50¢/50¢/$1 Coin Door

Figure 22 American-Made Coin Door 71-10xXxx D

Page 46

Figure 22 American-Made Coin Door, continued Parts List

Part No. Description

31-1N4002 100V Silicon Rectifier 1N4002 Diode 65-441C General-Usage Low-Force Miniature Switch 70-11-47 Miniature Bayonet-Base Incandescent Lamp, Type #47 71-1201ADU U.S. $1.00 Coin Mechanism 71-1201FCH Swiss 1 Fr Coin Mechanism

71-1201MG German 1 DM Coin Mechanism 71-1202MG German 2 DM Coin Mechanism 71-1205FB Belgian 5 Fr Coin Mechanism 71-1205MG German 5 DM Coin Mechanism 71-1210PE U.K. 10 P Coin Mechanism 71-1220CA Australian 20¢ Coin Mechanism 71-1225CU U.S. 25¢ Coin Mechanism 71-12100LI Italian 100 Lire Coin Mechanism 71-12100YJ Japanese Y100 Coin Mechanism 72-HA1404C, #4 x ¥4-Inch Slotted Pan-Head Thread-Rolling Tri-Fluted “Taptite” Cadmium-Plated Screw 72-JA1405B #4 x 5/16-Inch Slotted Pan-Head Thread-Rolling Tri-Fluted “Plastite” Black Screw 72-9406S #4-40 x 3/8-Inch Slotted Truss-Head Steel Machine Screw 72-9603S #6-32 x 3/16-Inch Slotted Truss-Head Steel Machine Screw 75-915S #%-20 Standard-Pattern Cadmium-Plated Steel Hex Nut 75-918S #832 Standard-Pattern Cadmium-Plated Steel Hex Nut 75-944S #4-40 Polymer Self-Locking Steel Hex Nut 75-948S, #8-32 Polymer Self-Locking Steel Hex Nut 75-1408S #4-40 x ¥2-Inch Slotted Pan-Head Steel Machine Screw 75-1412 #4-40 x 34-Inch Slotted Pan-Head Sieel Machine Screw 75-5520B #¥%4-20 x 1¥%-Inch Round-Head Square-Neck Steel Bolt with Black Finish 99-10008 Switch Wire Retainer 99-10009 2-Mech Coin Door Only 99-10010 3-Mech Coin Door Only 99-10011 Inner Panel 99-10012 U.S. 25¢ Coin Return Button Assembly 99-10013 U.S. $1.00 Coin Return Button Assembly 99-10014 German 1 DM Coin Return Button Assembly 99-10015 German 2 DM Coin Return Button Assembly 99-10016 German 5 DM Coin Return Button Assembly 99-10017 Belgian 5 Fr Coin Return Button Assembly 99-10018 Swiss 1 Fr Coin Return Button Assembly 99-10019 Japanese Y100 Coin Return Button Assembly 99-10020 U.K. 10 P Coin Return Button Assembly 99-10021 Australian 20¢ Coin Return Button Assembly 99-10022 Italian 100 Lire Coin Return Button Assembly 99-10040 Coin Inlet Chute Assembly 99-10041 Coin Counter Assembly 99-10042 Coin Switch Assembly for U.S. 25¢ and Belgian 5 Fr Coins (si/ver wire) 99-10043 Coin Switch Assembly tor German 1 DM, Swiss 1 Fr, and Japanese Y100 Coins (b/ack wire) 99-10044 Coin Switch Assembly for U.S. $1.00, German 2 DM, and Italian 100 Lire Coins (go/d wire)

Page 47

Figure 22 American-Made Coin Door, continued Parts List

Part No. Description

99-10045 Coin Switch Assembly for German 5 DM, U.K. 10 P, and Australian 20¢ Coins (green wire) 99-10047 Lockout Coil Assembly 99-10048 Coin Door Harness Assembly 99-10049 Locking Arm Assembly 99-10051 Coin Door Frame 99-10052 Coin Return Lever 99-10054 Coin Button Housing 99-10055 Coin Return Button Cover for Japanese 100Y Coin 99-10056 Coin Return Button Cover for German 1 DM and Swiss 1 Fr Coins 99-10057 Coin Return Button Cover for U.S. 25¢ and Belgian 5 Fr Coins 99-10058 Coin Return Button Cover for U.S. $1.00, German 2 DM, and Italian 100 Lire Coins 99-10059 Coin Return Button Cover for German 5 DM, U.K. 10 P, and Australian 20¢ Coins 99-10061 Coin Return Bezel 99-10062 Coin Return Button 99-10063 Right Half of Coin Inlet Chute 99-10064 Left Half of Coin Inlet Chute 99-10065 Coin Return Box 99-10066 Coin Return Cover 99-10070 U.S, 25¢ Price Plate 99-10071 Slam Switch Assembly 99-10073 Test Switch Decal 99-10074 Lock Assembly 99-10075 Black Switch Wire for German 1 DM, Swiss 1 Fr and Japanese 100Y Coins 99-10076 Silver Switch Wire for U.S. 25¢ and Belgian 5 Fr Coins 99-10077 Gold Switch Wire for U.S. $1.00, German 2 DM and Italian 100 Lire Coins 99-10078 Green Switch Wire for German 5 DM, U.K. 10 P and Australian 20¢ Coins 99-10080 Miniature Bayonet-Base Lamp Socket 99-10081 Wire Key Holder 99-10082 Switch Cover 99-10083 U.S. $1.00 Price Plate 99-10084 German 1 DM Price Plate 99-10085 German 2 DM Price Plate 99-10086 German 5 DM Price Plate 99-10087 Belgian 5 Fr Price Plate 99-10088 Swiss 1 Fr Price Plate 99-10089 Japanese Y100 Price Plate 99-10090 U.K. 10 P Price Plate 99-10091 Australian 20¢ Price Plate 99-10092 Italian 100 Lire Price Plate 99-10094 Fish Paper Insulation 99-10095 Toggle Switch 99-10096 “U"-Type Fastener 99-10097 Fish Paper Insulation 99-10101 Coin Inlet Chute Sub-Assembly 99-10102 Switch and Lockout Coil Bracket Sub-Assembly 99-10103 Inner Panel with Levers Sub-Assembly 99-10104 Anti-Penny-Flip Bar Retainer 99-10105 Anti-Penny-Flip Bar 99-10107 U.S. 50¢ Coin Return Button Assembly (for two quarters) 99-10108 U.S. 50¢ Price Plate (for two quarters)

Page 48

99-15038 (Bezel for Button) NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL; Reproduction forbidden without the gpecilic written permission of Atari, Inc. Sunnyvale, CA. This drawing is. only conditionally’ issued, and neither receipt nor possession thereof confers or \ransfers any Tight in, or license to use, the subject matter of the drawing or any design or technical information shown thereon, not any fight to reproduce this drawing or any part 99-1501 thru 99-15012 thereof. Except for manufacture by vendors of Atari, Inc., (Ret. Button) and tor manufacture under the corporation's written license, no right to reproduce this drawing is granted or the subject matter thereof unless by written agreement with of written permission from the corporation.

99-15052 (Spring tor Button),

99-15054 (Lamp Holder)

. 99:15040 99-15026 (Lever) — (Coin Inlet)

cad 9915039 a \ (Bezel tor Cover) 99-15036, . (Cover) 99-15056 (Screw for Bezel)

(Coin Inlet)

PART OF

99-15041

99-15054 99-15055 of\ - 99-15041 ls a (Pivot for Lever) (Retng. Screw) > SA (Lockout Coil) we 99-15053 aN ! (Lockt. Col Spring) << NJ

99-15027 (Coin Ret. Box)

~+——— 99-15028 (Goin Ret. Box)

99-15037 (Sw. Adjuster 99-15056 (Screw for Bezel) 99-15060 _— (Sw. Cover) 9915029 (Bracket)

(Switch) a

171000-xxx A

Page 49

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific written permission of Atari, Inc., Sunnyvale, CA. This drawing is only conditionally’ issued, and neither receipt nor possession thereot Confers or transfers any right in, of license to use, the subject matter of the draw ing or any design or technical information shown thereon, nor any right to reproduce this drawing or any part thereof. Except for manufacture by vendors of Atari, !nc., and for manufacture under the corporation's wiitien license, no right to reproduce this drawing is granted or the subject matter thereot unless by written agreement with of written permission irom the corporation:

171001001 — British 10 P/10 P Coin Door 171000-002 — British 10 P/50 P Coin Door 171000-003 — British 20 P/50 P Coin Door 171000-004 — German 1 DM/1 DM Coin Door 171000005 — German 2 DM/1 DM Coin Door 171000-008 — German 2 DM/5 DM Coin Door 171000007 — Belgian 5 Fr/5 Fr Coin Door 171000008 — French 1 Fr/1 Fr Coin Door 171000-008 — French 2 Fr/1 Fr Coin Door 171000-010 — Swedish 1 Kr/1 Kr Coin Door 171000-011 — Hong Kong $1/$1 Coin Door 171000-012 — Canadian 25%/25¢ Coin Door 171000-013 — U.S. 25°/25¢ Coin Door 171000-014 — Spanish 25 Pts/25 Pts Coin Door 171000-015 — Swiss 1 Frit Fr Coin Door

Figure 23 _British-Made Coin Door 171000-xxx A

Page 50

Figure 23 British-Made Coin Door, continued Parts List

Part No. Description

99-15001 Coin Return Button with U.S. 25¢ Price Plate 99-15002 Coin Return Button with U.S. $1 Price Plate 99-15003 Coin Return Button with German 1 DM Price Plate 99-15004 Coin Return Button with German 2 DM Price Plate 99-15005 Coin Return Button with German 5 DM Price Plate 99-15006 Coin Return Button with Belgian 5 Fr Price Plate 99-15007 Coin Return Button with French 1 Fr Price Plate 99-15008 Coin Return Button with Japanese 100 Yen Price Plate 99-15009 Coin Return Button with British 10 Pence Price Plate 99-15010 Coin Return Button with Australian 20¢ Price Plate 99-15011 Coin Return Button with Italian 100 Lire Price Plate 99-15012 Coin Return Button with U.S. 50¢ (2 x 25¢) Price Plate 99-15025 Left Half of Coin Inlet 99-15026 Right Half of Coin Intet 99-15027 Side Plate of Coin Return Box 99-15028 Base Plate of Coin Return Box 99-15029 Switch Bracket 99-15030 Flap for Lockout Coil (U.S. 25¢) 99-15036 Coin Return Cover 99-15037 Switch Adjuster 99-15038 Bezel for Coin Return Button 99-15039 Bezel for Coin Return Cover 99-15040 Coin Return Lever 99-15041 Lockout Coil 99-15042 Coin Switch for U.S. 25¢ 99-15051 Lamp Holder 99-15052 Spring for Coin Return Button 99-15053 Spring for Lockout Coil 99-15054 Pivot for Coin Return Lever 99-15055 Retaining Screw 99-15056 Screw for Both Bezels 99-15060 Switch Cover

Page 51

1st printing

YOUR COMMENTS, PLEASE!

Your comments will assist Atari in improving the usefulness of our publications. They are an important part of preparing for revisions of manuals and parts catalogs. No postage stamp is necessary if mailed in the U.S.A.

!f you have any technical questions about certain Atari or Kee Games products, or are requesting additional publications, we wil! immediately forward your note to the appropriate person.

Page: Comments:

Fill in if you wish a reply:

Name.

Firm Ci Distributor

Address J] Operator

City State Zip C) Other.

Area Code Phone

Page 52

No Postage Necessary if mailed in the United States

BUSINESS REPLY MAIL

FIRST CLASS PERMIT.NO. 1004 SUNNYVALE,CA POSTAGE WILL BE PAID BY ADDRESSEE

Atari, Inc. Attn.: Field Service/Coin-Op Division P. O. Box 427 Sunnyvale, California 94086

Second fold

abpe siyy ede, aut siyy Buoye ynD

Page 53

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 54

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 55

aa

=e ° > id > > ES SE ES SS

Warranty

Seller warrants that its printed circuit boards and parts thereon are free from defects in material and workmanship under normal use and service for a period of ninety (90) days from date of shipment. Seller warrants that its television monitors (in games supplied with monitors) are free from defects in material and workmanship under normal use and service for a period of thirty

  • days from date of shipment. None of the Seller's other products or parts thereof are warranted

If the products described in this manual fail to conform to this warranty, Sellers’ sole liability shall be, at its option, to repair, replace, or credit Buyer's account tor such products which are returned to Seller during said warranty period, provided:

  • Seller is promptly notified in writing upon discovery by Buyer that said products are defective;
  • Such products are returned prepaid to Sellers’ plant; and
  • Seller's examination of said products discloses to Seller's satisfaction that such alleged defects existed and were not caused by accident, misuse, neglect, alteration, improper repair, installation or improper testing

In no event shall Seller be liable for loss of profits, loss of use, incidental or consequential damages

Except for any express warranty set forth in a written contract between Seller and Buyer which contract supersedes the terms of this order, this warranty is expressed in lieu of all other warranties expressed or implied, including the implied warranties of merchantability and fitness for a particular purpose, and of all other obligations or liabilities on the Seller's part, and it neither assumes nor authorizes any other person to assume for the Seller any other liabilities in connection with the sale of products under this order.

The use of any non-Atar parts may void your warranty, according to the terms of the warranty. The use of any non-Atari parts may also adversely affect the safety of your game and cause injury to yourself and others. Be very cautious in using non-Atari-supplied components with our games, in order to insure your safety.

Atari distributors are independent, being privately owned and operated. In their judgment they may sell parts or accessories other than Atari parts or accessories. Atari cannot be responsible for the quality, suitability or safety of any non-Atari part or any modification including labor which is performed by such distributor

This document is and contains confidential trade secret information of Atari, Inc.

This document is loaned under confidential custody for the sole purpose of operation, maintenance or repair of Atari equipment and may not be used by or disclosed to any person for any other purpose whatever, and remains the property of Atari, Inc.

Neither it nor the information it contains may be reproduced, used, or disclosed to persons not having a need to know consistent with the purpose of the loan, without written consent of Atari, Inc. © £ s s s

bs

Page 56

ATARI

ATARI INC 1265 BORREGAS AVENUE P.O. BOX 427 SUNNYVALE, CALIFORNIA 94086, 408/745-2000 ¢ TELEX 35-7488 ovo conmancanima coneney