Eagle
Moon Cresta (Nichibutsu) (Nichibutsu, 1980) · Manual · 20 pages · 4 sections · original scan
REFERENCE MANUAL
centri. HIALEAH. FLORIDA.U.S.A
"EAGLE"
OPERATION AND MAINTENANCE
MANUAL
CENTURI, INC.
245 WEST 74TH PLACE
HIALEAH, FLORIDA 33014
TABLE OF CONTENTS
PAGE:
EAGLE UPRIGHT.....--+-
INTRODUCTION. ........-
GAME PLAY....-.eeeeees eee revccsreeldyd EAGLE POINT SCORING... 1. eee eee cee e cece sees cence need HIGH SCORE NAME REGISTRATION... .eeeeeeceeeeeereeed
METHOD OF REGISTRATION. ....-eeeeeeee eee r es cee eee eed INSTALLATION... cc cece ccc c cece eee e cece e eee ence ee & ELECTRICAL REQUIREMENTS.....e ce eecceee cere ee cece 6 MAINTENANCE AND SERVICE... cee eeee eee cece eee e eee nh GENERAL INFORMATION.......
OPERATOR OPTIONS...... se eee wens
SWITCH OPTIONS... cc eeeece cece cee ce eee ceeseeece eee sd COLOR VIDEO MONITOR ADJUSTMENTS.......ee eee ee eee nD
&
INTRODUCTION
EAGLE is a one or two player action game that offers a mode of play designed to intrigue the player, and ensure prolonged interest.
The simplicity of control panel design, with the two button left/right directional control and the one button fire control, challenge the player's dexterity.
As the rocket is visually launched in the center of the screen, aliens attack the rocket enmass. As each wave attacks, the intensity of play increases. The player maneuvers his rocket to avoid collisions, and fires missiles to destroy the enemy.
A bonus feature of the game is the docking maneuver. Through use of the bidirectional control buttons, and the fire button as a retro control, the player can score extra bonus points by docking the rocket. The highest score is achieved by docking in the shortest period of time.
GAME_PLAY
There are three modes of play in EAGLE: 1.) The Attract Mode 2.) The One-Player Mode 3.) The Two-Player Mode
The Attract Mode is activated when power is turned on. Initially, there is a video introduction to the game, then the top five high score names are registered. Next, the three stage rocket appears, with the explanation of of the docking maneuvers with rockets I and II. After the docking maneuver, each stage rocket appears on the screen, and fires at waves of aliens until it is destroyed. The attract mode ends when all three stages of rocket are destroyed.
The One-Player Mode is activated when a coin is accepted and the player pushes the one-player button. The three stage rocket appears, and there is an audio introduction. The first stage rocket breaks away from the rest of the rocket, and play begins. The player manipulates the movement of the rocket by pushing the left/right directional buttons, and fires at the aliens with the fire button. The first stage rocket fires one missile at a time, until it is destroyed by the aliens. If the rocket destroys the first four waves of aliens, it encounters the first stage docking maneuver bonus. After it docks with the second stage rocket, then the rocket has the ability to fire three missiles at a time at the next two waves of aliens, and then the comet wave. The rocket is then able to try for the second stage docking maneuver bonus. After that is completed, the player then goes on to two additional waves. Having completed eight waves of aliens, one wave of comets, and two docking maneuvers, the program begins all over again, at a slightly faster rate of speed. When all three stages of the rockets have been destroyed V4
the game is over.
The Two-Player Mode is activated when a coin is accepted and the players push the two-player button. The pattern of play is identical to the pattern of play for the one-player mode, except that when the first player has his first stage rocket destroyed, the second player begins play with his first stage rocket. When the second player's first stage rocket is destroyed, then play reverts back to the first player, who will then have his second stage rocket to destroy the aliens. When his second stage rocket is destroyed, then the second player begins play with his second stage rocket. The same applies to the third stage rocket for both players. The game is over when both players have had all three stages of rockets destroyed.
EAGLE POINT SCORING:
NO. TARGETS: POINT VALUE:
| Green Mantas: | 4 Whole Targets | 50 Points for |
that break in half each half when hit. destroyed. Total = 8 Targets.
| Pink Mantas: | 4 Whole Targets | 50 Points for |
that break in half each half when hit. destroyed. Total = 8 Targets.
| Pink Tegors: | 8 Targets. | 30 Points each. |
| Blue Tegors: | 8 Targets. | 30 Points each. |
First Stage docking maneuver: 100 points per seconds remaining. Maximum points = 1900 points.
| Red Eagles: | 8 Targets. | 60 Points each. |
| Blue Eagles: | 8 Targets. | 60 Points each. |
| Comets: | 8 Pair Targets | 200 Points each. |
= 16 Targets.
Second Stage docking maneuver: 200 points per seconds remaining. Maximum points = 4200 points.
| Pink Volars: | 8 Targets | 100 Points each. |
| Green Volars: | 8 Targets | 100 Points each. |
Program pattern then begins with the Mantas again, at a slightly faster rate of speed.
HIGH SCORE NAME REGISTRATION:
The High Scorer's name can be registered on the screen.
Any unwanted wording can be cancelled by turning the game off at the service switch, and the high score will then be cancelled.
METHOD OF REGISTRATION:
The letters ("A"-"Z"), "Space", "Rub", and "End" will be displayed on the screen. By moving the control lever, move the underline through the alphabet one letter at a time, so that the high scorer's initials can be spelled.
A letter above the underline can be registered on the screen by pushing the fire button.
"RUB": If a wrong letter has been registered, move the underline to the word "Rub", then push the fire button and the letter will be cancelled.
"END": To finish the high scorer's initial registration, move the underline to the word "End" and push the fire button.
The high scorer's initial registration must be performed within one minute. After one minute has passed, the registration will automatically end. (In total, three letters can be registered).
INSTALLATION
Your game was shipped in ready-to-play condition. A brief visual examination is suggested after removal from the shipping carton.
Any damage to the game cabinet and external components should be noted for freight claim purposes. Any damage to the exterior would indicate possible interior damage as well.
Briefly examine the interior of the game for disconnected wires, cables or harnesses and electronic devices loose in their sockets, etc. Log the game serial number, as it will be required for reference and servicing.
ELECTRICAL REQUIREMENTS
Unless specified otherwise, your game is set to operate at 115vVAc, 50/60 HZ. Two other voltage settings are possible, and these options and fusing requirements are listed on the power supply chassis.
A good ground is essential for the proper operation of this game. Instability and erratic operation can be traced to ineffective ground.
MAINTENANCE AND SERVICE
This machine should require very little maintenance and only occasional adjustments, due to the solid-state electronic circuitry.
Certain precuations should be observed to avoid damage to the game.
Service should be done by a qualified technician.
CENTURI Customer Service Department can be reached outside Florida at: #1-800-327-6749, or in Florida: #1-305-887-5528.
GENERAL INFORMATION
Your CENTURI game is designed much the same as other conventional video games. The game is built with the same basic assemblies:
The Power Supply unit provides all necessary voltages for each separate electronic assembly, as well as the AC lighting required throughout the game.
The Central Processing Unit (CPU or logic unit) contains the circuitry necessary to interpret all input functions which include the player control panel switches, all coin and credit information, and generates all the digital signals used to provide the visual display and control the audio effects. It also contains all the software (machine language and game personality memory) needed to control the game operation.
The Audio Control (volume control) is located on the main logic board, and can be easily adjusted by rotation of the volume pot. To maximize play time, the audio level should compete with the other machines.
OPERATOR OPTIONS
The option switch is located on the main logic board. See the Option Switch settins diagram for settings.
The option switch and audio control can easily be reached through the back of the game.
SWITCH OPTIONS
| SWITCH: | ON/OFF: | DESCRIPTION: |
| 1 | OFF | Replay for 30,000 Points. |
| 1 | ON | Replay for 50,000 Points. |
| 2 | OFF | Japanese Docking Instructions. |
| 2 | ON | English Docking Instructions. |
| 3 | -- | Not Used. |
| 4 | — | Not Used. |
1 COIN FOR 1 PLAY 5 6 OFF | OFF
ON OFF 1 COIN FOR 2 PLAYS
OFF | ON 1 COIN FOR 3 PLAYS for [om FREE PLAY
COLOR VIDEO MONITOR _ADJSUTMENTS
The video monitor is properly adjusted before shipping.
Occasionally adjustments are necessary and for this reason, a complete technical manual for the monitor is included with each game.
All adjustment control locations are located on the back of the monitor chassis.
Vertical Hold: Adjust vertical hold if picture rolls vertically.
Horizontal Hold: Adjust horizontal hold if the picture is warped or broken into diagonal lines. (Use caution when adjusting this control).
Focus: Adjust focus if picture is fuzzy.
Red, Green and Blue Colors: Adjust red screen, green screen and blue screen controls.
For additional adjustments and information, refer to the monitor manual.
USER INFORMATION - F.C.C.
THIS EQUIPMENT GENERATES, USES AND CAN RADIATE RADIO
FREQUENCY ENERGY AND IF NOT INSTALLED AND USED IN ACCORD-
DANCE WITH THE INSTRUCTIONS MANUAL, MAY CAUSE INTERFERENCE
TO RADIO COMMUNICATIONS. AS TEMPORARILY PERMITTED BY REGU-
LATION, IT HAS NOT BEEN TESTED FOR COMPLIANCE PURSUANT TO
SUBPART J OF PART 15 OF F.C.C. RULES, WHICH ARE DESIGNED
TO PROVIDE REASONABLE PROTECTION AGAINST SUCH INTERFERENCE.
OPERATION OF THIS EQUIPMENT IN A RESIDENTIAL AREA IS LIKELY
TO CAUSE INTERFERENCE IN WHICH CASE THE USER AT HIS OWN EX-
PENSE WILL BE REQUIRED TO TAKE WHATEVER MEASURES MAY BE RE-
QUIRED TO CORRECT THE INTERFERENCE.
INSTALLATION
Your game was shipped from the factory in ready-to-play condition. A brief inspection is suggested before the machine is removed from the carton. If there is damage to the shipping carton, contact the freight carrier for claim purposes. External damage could indicate possible damage to the cabinet and/or
electronics components.
After the carton has been satisfactorily inspected, remove the machine from the shipping carton.
Examine the interior of the game for disconnected wires, cables, or harnesses. Make sure the electronic devices are se-
curely mounted in their sockets, etc. Record the game serial number since it will be required for reference and servicing.
ELECTRICAL REQUIREMENTS
Unless otherwise specified, this game is set to operate at 110 Volts A.C. See Figure-1- for 110/220 VAC conversion in-
structions. Power Supply Chasis schematic information and parts list are included in this manual.
FIGURE -1-
110/220 VAC CONVERSION INSTRUCTIONS:
This video arcade game has a harnessing configuration that allows the machine to be operated from either a 110 VAC or 220 VAC @ 50 or 60Hz power source, with only minor changes. The only items requiring a change are the fuses and the jumper plug on the game power transformer.
FIRST: Unplug the machine from the wall outlet to completely eliminate shock hazards.
SECOND: Remove the two fuses in the A.C. distribution bracket.
THIRD: Remove the jumper plug on the game power transformer located on the floor of the machine.
FOURTH: Depending on what voltage you wish to run the game from, do the following:
110 VAC
Replace the two fuses that go in the bracket with the 3 AMP, SLOW-BLOW types. Next, plug in the orange jumper plug labeled 110 VAC. The machine can now be operated with an input voltage of 110 Volts A.C.
220 VAC
Replace the two fuses that go in the bracket with 14-AMP, SLOW-BLOW types. Next, plug in the red jumper plug labeled 220 VAC. The machine can now be operated with an input voltage of 220 Volts A.C.
ROUTINE MAINTENANCE & SERVICE
Because of the solid state electronic circuitry, this machine should require very little maintenance and only occasional adjustments. However, it is necessary to take measures to insure this.
The volume control is located on the bottom side of the
printed circuit board farthest from the side of the cabinet, and can be accessed through the rear door.
The video monitor has been properly adjusted before ship-
ping. Occasionally minor adjustments are necessary. See monitor specifications and schematics for technical information. Adjustment controls for the monitor are located at the rear
of the monitor.
This machine should be serviced only by a qualified
technician.
Do not make any adjustments on this machine while the
power is on.
For service information, contact:
CENTURI, INC.
Customer Service Department #800-327-7710(Outside the state of Florida) #305-556-5888 (In Florida)
POWER SUPPLY
The computer Board in this game operates most efficiently and reliably when the power supply is set so that the voltage on the board is 5.0 Volts, +0.1 Volts. To check this, place a meter across 5 Volts and ground at the edge connector. If necessary, adjust the screwdriver control on the power supply so the meter reads between 4.9 and 5.1 Volts.
SYMBOL:
Ti
Ll L2, L4 L3
D1 D2 D3, D6
D5, D7 D12, D13 D14
Ql Q2
Q4
Icl
Pcl
R1 R8, R9 R3, 1-4
R12 R28
R26 R23 R10 R27 R2 R22 R21 R6 R11 R20 R17 R19 R18 R5 R16 R29 R39 R38 R24 R25 RV1 PARTS LIST - SHINDENGEN POWER SUPPLY
DESCRIPTION:
TRANSFORMER, SINGLE PHASE, 2A VA
CHOKING COIL, 1.6mH, 1.5A CHOKING COIL, SF-T8-50S-03 CHOKING COIL, SF-HP-2A-03
DIODE, V19G DIODE, VO6C DIODE, 181588 DIODE, S15S3 DIODE, 5CH1M DIODE, F113B DIODE, F113B DIODE, S4VB40(BRIDGE TYPE)
TRANSISTOR, TRANSISTOR, TRANSISTOR, TRANSISTOR, 2S8C2504 2SD467 (B) 2SC460 (B) 2SA673 (B)
INTEGRATED CIRCUIT, RM723DC or HA17723G-02 PHOTO COUPLER, PS2001
RESISTOR, 2 RESISTOR, RESISTOR, RESISTOR, RESISTOR, RESISTOR, RESISTOR, RESISTOR, BRR EENN WATT, 18 OHM WATT, 47K OHM WATT, 15 OHM WATT, 56 OHM WATT, 100 OHM WATT, 470 OHM WATT, 0.56 OHM WATT, 0.82 OHM RESISTOR, 1/4 WATT, 22 OHM RESISTOR, 1/4 WATT, 33 OHM RESISTOR, 1/4 WATT, 68 OHM RESISTOR, 1/4 WATT, 330-470 OHM RESISTOR, 1/4 WATT, 220 OHM RESISTOR, 1/4 WATT, 270 OHM RESISTOR, 1/4 WATT, 330 OHM RESISTOR, 1/4 WATT, 68 OHM RESISTOR, 1/4 WATT, 470 OHM RESISTOR, 1/4 WATT, 680 OHM RESISTOR, 1/4 WATT, 800 OHM RESISTOR, 1/4 WATT, 1.2K OHM RESISTOR, 1/4 WATT, 10K OHM RESISTOR, 1/4 WATT, 220K OHM RESISTOR, 3 WATT, 27 OHM RESISTOR, 1/4 WATT, 4.7K OHM RESISTOR, 1/4 WATT, 5.6K OHM RESISTOR, 1/4 WATT, 330 OHM RESISTOR, 1/4 WATT, 150 OHM VARIABLE RESISTOR, RJ-6P501 USAGE:
PRPNNEPNEE BNE
PRRE
Be
PER RP RPP REP REE PEER BRP HPRP RHP EPRPEP ANE
PARTS LIST - SHINDENGEN POWER SUPPLY
SYMBOL:
C1, C2 C3-1,-2 c9, C10 C11, C23 C12, C13, C15 C27 C18, C19, C20 C26 C21, C22, C25
c14, C16 DESCRIPTION:
CAPACITOR, CAPACITOR, CAPACITOR, CAPACITOR, CAPACITOR, CAPACITOR, CAPACITOR, CAPACITOR, CAPACITOR, CAPACITOR, CAPACITOR, CAPACITOR, CAPACITOR, CAPACITOR, CAPACITOR, ECK-DAL102E 160VSN100 SM10VB-2200 SM10VB-2200 SL25VB-10 SL25VB-10 SM35VB-1000 SM35VB-1000 SM16VB-1000 DMY21H472K DMY21H104K DMY21H222K CM20XC511K5 MDD22G473K DMY21H222K
ENCLOSED TYPE FUSE, 3A USAGE:
BPRPENEPRPWRPWRPWNNNN
Nu
THE MATERIAL CONTAINED HEREIN 1S CONFIDENTIAL AND NO PART OF IT CAN BE REPRODUCED WITHOUT THE EXPRESSED PERMISSION OF ALLIED LEISURE IND., INC. Ri ware ee ee 22 AWG WHITE WIRE 5 Fez / Aw 82 44") | iz 95 (14) ae 92 (16") GRAY omPe Wik Fecawe 30 (48") GRA Ae ee wire Fax AWG 46 ) Gay, VAs Betek WIRE, #22 AWG ues | Be je WRE, Bea A AWG 9548) GREEN BO WIRE 922 AWG 37 (48') GREEN WIRE 9 22 AWG 7 GREEN [ERE Ry BRRANG r [50175306 [GREEN /GRILB™ wae, Fez AWG
| s} 20-87) 1.) | ertene| | mn | ea | |
| CPU | $5.27) | | | 017970 | |
| Pa | | \ | —_ | - | BLU |
4Y4-PIN EDGE Conn, G-Pit NoKeX 5502") 6H) RECEPTACLE.
RED WIRE , #22 AWG
i BLACK WIRE , #22 AWG gles C42") 4” wire Ties
| i | i | 3he" FAST-ONS | |||
| L | $2. (42") | | | “RECEP. To. | ae | et |
| (42") | CC IN | 6 |S015009@ | OPEN LUGS | ||
| 10 | aa! | t | BOR. | 1 |so1goras | RING LUG | |
| 41,13 | £4 (42) | i | 12 |50156223| MOLEX FEMALE PINS | ||
| MyP | 50 (42") | i | 50150269 | AMP FEMALE PINS | ||
| 12. | 56 (42") | | | G-PIN MOLEX RECEPTACLE |
? 7 AZ-PIN MOLEX RECEPTACLE
| af | urease | Lo | ZA-FIN AMP RECEPTACLE |
| z | iL (eE') | 1] | YH-PIN EDGE COARCETOR, |
TO. AB-PIN MOLEX Ri 2 SE OF MATERIALS ALLIED LEISURE INDUSTRIES, INC. [Unless Otherwise Specitied | HIALEAH, FLORIDA.33014 + + NAME = ga[ CRY HARNESS 19” EAGIE
| BHT. MET BENDS | b. | Joate | Part NO.3G, | 1 |
Ke WE [ts Fe |
THEsMATEBIAL CONTAINED HEREIN 1S CONFIDENTIAL . AND NO PART OF IT CAN BE REPRODUCED WITHOUT THE *, EXPRESSED PERMISSION OF ALLIED LEISURE IND., INC. LEFT SW, RIGHT sw. FIRE Sw. 1 PLAYER Sw. 2 PLAYER. SW.
as (72) e5(2" o ( 7%") 54 C48") se_(7%") 52 (218")
Jz | 85 (0°) __a@ cuassis L___j 12-PIN MOLEX PLUG
[reevethine 24 SneeN BLACK 22AWG| a PANEL. CONN a CONTROL 4 é
ee ee ee eee a = [ ac. arvo[ Prov. apvol ary. [Assematy on | HIALEAH, FLORIDA. 33014 ““ CONTROL PANEL HARNESS j bse CS DECIMALS2 PL DECIMALS 3PL
amucrecwss ee [Pater [Se Lei ia-o700 I