CATHODE RAY TOMES

Badlands Universal Kit TM-344 1st Printing

Bad Lands (Atari Games, 1989) · Technical Manual · 62 pages · 63 sections · original scan

Page 1

weg we” yall Sat ae a oe 3a

or

4 _ Universal Kit

Installation Instructions

Page 2

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 3

Kit INSTALLATION INSTRUCTIONS

“te

Page 4

Copyright © 1989 by Atari Games Corporation. All rights reserved. No part of this publication may be reproduced by any mechanical, photographic or electronic process, or in the form of a phonographic recording, nor may it be stored in a retrieval system, transmitted, or otherwise copied for public or private use, without permission from the publisher. The game play, all graphic designs, this technical manual, its accompanying schematic diagrams, and the display manual are protected by the U.S. Copyright Act of 1976. This Act provides for substantial penalties for violating federal copyright laws. Courts can impound infringing articles while legal action is pending. If infringers are convicted, courts can order destruction of the infringing articles. In addition, the Act provides for payment of statutory damages of up to $50,000 per infringing transaction in certain cases. Infringers may also have to pay costs and attorneys’ fees and face an imprisonment of up to five years as well as fines of up to $250,000 in the case of individuals and up to $500,000 in the case of corporations. Atari Games Corporation will aggressively enforce its copyrights against infringers. We will use all legal means to immediately halt any manufacture, distribution, or operation of a copy of video games made by us. Anyone who purchases such copies risks forfeiting such a game.

Published by: Atari Games Corporation 675 Sycamore Drive P.O, Box 361110 Milpitas, California 95035

Printed in the U.S.A 12/89

Produced by the Atari Games Technical Publications Department. Technical Writing: Rosalind Hutton Editing and Text layout: Andrea Dencker Illustration and Design: Mary Ohanessian Sumner

ii Badlands Universal Kit

Notice Regarding Non-Atari’ Parts

WARNING Use of non-Atari parts or modifications of any Atari game circuitry may adversely affect the safety of your game, and may cause injury to you and your players.

You may void the game warranty (printed on the inside back cover of this manual) if you do any of the following:

  • Substitute non-Atari parts in the game.
  • Modify or alter any circuits in the game by using kits or parts not supplied by Atari Games Corporation.
NOTE This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instruction manual, may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of Federal Communications Commission (FCC) Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area or modification to this equipment is likely to cause interference, in which case the user, at his own expense, will be required to take whatever measures may be required to correct the interference. If you suspect interference from an Atari game at your location, check the following: All ground wires in the game are properly connected as shown in the game wiring diagram.
  • The power cord is properly plugged into a grounded three-wire outlet.
  • On games provided with an Electromagnetic Interference (EMD ground cage, be sure that the game printed-circuit boards (PCBs) are properly installed on the EMI ground cage and that the end board is securely installed with all screws in place and tightened. If you are still unable to solve the interference problem, please contact Customer Service at Atari Games Corporation. See the inside front cover of this manual for service in your area.
Page 5

Badlands Universal Kit

Contents

1 Installation How to Use This Manual . Equipment Requirements. Tools Required.

  • Inspecting the Kit Preparing the Cabinet for the Kit Installation Installing the Kit Parts Testing After Power-Up Setting the Coin and Game Options. Game Play ....

2 Self-Test Entering and Exiting the Self-Test... RAM and ROM Test Self-Test Menu .... Statistics Histogram. Coin Options. Game Options. Input Test... Playfield Stamp Test Motion Object Test . Motion Object Picture Test Playfield and Convergence Pattern Test. 27 Color Bars and Color Purity Test...... Sound Test...

3 Maintenance and Troubleshooting Video Display .. 3-4 Steering Assembly. 3-4 Pedal Assembly...

4 Illustrated Parts Lists See the list of illustrations and list of tables that follows.

5 Schematics See the list of illustrations that follows.

Glossary

Statistics Sheet

Illustrations

Figure 1-1 Assembling the Pedal 1-2 Installing the Pedals on the Game 1-3. Assembling the Control Panel..... 1-4

Figure 2-1 2-2

2-6

2-8

2-10

2-11

2-12

Figure 3-1 Figure 4-1 4-2

Figure 5-1

5-2

Table 1-1

Table 2-1 2-2

2-4 2-5 2-6

2-8

Table 3-1 3-2 Badlands Kit Parts Installed in a Cabinet

Self-Test Menu Screen Statistics Screen. Histogram Screen. Coin Options Screen . Game Options Screen Input Test Screen.... Playfield Stamp Test Screen Motion Object Test Screen.. Motion Object Picture Test Screen Playfield and Convergence Pattern Test Screen... Color Bars and Color Purity Test Screen... Sound Test Screen Pedal Installation Template ..... Maintaining the Steering Assembly. Steering Assembly... Badlands Game PCB Assembly.......... 44 Badlands Games PCB Assembly Schematic Diagram (6 sheets)... Steering PCB Schematic Diagram, Faulty RAM and ROM Tables, and Badlands Memory Map.

Tables

Equipment Requirements.. Kit Contents List.. JAMMA Pin and Wire Connections Summary of All Self-Test Screens. Bad RAM Locations... Bad Upper or Lower ROM Locations Coin Option Settings . Game Option Settings Motion Object Test . Motion Object Picture Test Error Locations .... . Faulty Sound RAM and ROM Locations ceseeeteeeteeees Troubleshooting Table... Voltage Inputs and Test Points on the PCBs.. ‘What ROM Problems Look Like Atari Video Connector Pin Assignment: Badlands Kit Parts List

iii

Page 6

Badlands Universal Kit

Safety Summary

The following safety precautions apply to all game operators and service personnel. Specific warnings and cautions will be found in this manual whenever they apply.

WARNING Properly Ground the Game. Players may receive an electrical shock if this game is not properly grounded! To avoid electrical shock, do not plug in the game until it has been inspected and properly grounded. This game should only be plugged into a grounded threewire outlet. If you have only a two-wire outlet, we recommend you hire a licensed electrician to install a three-wire grounded outlet. If the control panel is not properly grounded, players may receive an electrical shock! After servicing any part on the control panel, check that the grounding wire is firmly secured to the inside of the control panel. After you have checked this, lock up the game. AC Power Connection. Before you plug in the game, be sure that the game’s power supply can accept the AC line voltage in your location. The line voltage requirements are listed in the first chapter of this manual. Disconnect Power During Repairs. To avoid electrical shock, disconnect the game from the AC power before removing or repairing any part of the game. If you remove or repair the video display, be very careful to avoid electrical shock. High voltages continue to exist even after power is disconnected in the display circuitry and the cathode-ray tube (CRT). Do not touch the internal parts of the display with your hands or with metal objects! Always discharge the high voltage from the CRT before servicing it. Do this after you disconnect it from the power source. First, attach one end of a large, well-insulated, 18-gauge jumper wire to ground, Then momentarily touch the free end of the grounded jumper wire to the CRT anode by sliding the wire under the anode cap. Wait two minutes and do this again. Use Only Atari Parts. To maintain the safety of your Atari game, use only Atari parts when you repair it. Using non-Atari parts or modifying the game circuitry

iv may be dangerous, and could injure you and your players. Handle the CRT With Care. If you drop the CRT and it breaks, it may implode! Shattered glass from the implosion can fly six feet or more. Use the Proper Fuses. To avoid electrical shock, use replacement fuses which are specified in the parts list for this game. Replacement fuses must match those replaced in fuse type, voltage rating, and current rating. In addition, the fuse cover must be in place during game operation.

CAUTION Properly Attach All Connectors. Make sure that the connectors on each printed circuit board (PCB) are properly plugged in. The connectors are keyed to fit only one way. If they do not slip on easily, do not force them. If you reverse a connector, it may damage your game and void your warranty. Ensure the Proper AC Line Frequency. Video games manufactured for operation on 60 Hz line power (used in the United States) must not be operated in countries with 50 Hz line power (used in Europe). If a 60 Hz machine operates on 50 Hz line power, the fluorescent line ballast transformer will overheat and cause a potential fire hazard. Check the product identification label on your machine for the line frequency required.

ABOUT WARNINGS, CAUTIONS,

AND NOTES In Atari publications, notes, cautions and warnings have the following meaning:

WARNING — Players and/or technicians can be killed or injured if instructions are not followed.
CAUTION — Equipment and/or parts can be damaged or destroyed if instructions are not followed. You will void the warranty on Atari printed-circuit boards, parts thereon, and video displays if equipment or parts are damaged or destroyed due to failure of following instructions.
NOTE — A highlighted piece of information.
Page 7

Chapter 1

Installation

How to Use This Manual

This manual provides information troubleshooting and maintenance

for installing, testing, and trouble- procedures. ™@ Chapter 4 contains

shooting the Badlands™ kit. The illustrated parts lists. m™ Chapter 5

manual is divided into the follow- contains the schematics for the

ing chapters: m Chapter 1 describes the installation Badlands game PCB and steering PCB. Also, at the end

procedure and the Badlands game play. ™@ Chapter 2 of Chapter 1, is the template for installing the pedals

contains self-test procedures. m™ Chapter 3 contains on the cabinet.

Page 8

Installation

WARNING To avoid electrical shock, unplug the cabinet while installing the kit. After installation, plug the game only into a grounded 3-wire outlet.

Equipment Requirements

Table 1-1 lists the equipment required in the cabinet into which you are installing the Badlands kit.

CAUTION Do not unplug or plug in the Badlands game printed-circuit board (PCB) edge connector while the power is on. You could seriously damage the PCB.

Tools Required

®@ Three C-clamps ® Drill with 5/16-inch drill bit, 3/16-inch drill bit, and a 1 3/16-inch hole cutter (or a 1 3/16-inch chassis punch) Phillips screwdriver Flat-blade screwdriver Socket set and ratchet 1/4-20 hex wrench Wire cutters and strippers Straight edge Squeegee Badiands Universal Kit

@ X-ACTO™ knife @ Fast-ons (if you are installing a new JAMMA harness)

Inspecting the Kit

Check to see that you have all the parts listed in the kit parts list in Table 1-2. If any part is missing or damaged, contact your distributor with the Badlands kit Table 1-2 Kit Contents List

Page 9

Badlands Universal Kit

serial number, part number and description of the missing or damaged parts, and date received.

Preparing the Cabinet for

the Kit Installation

  • Turn off power to the game.
  • Remove the following from the cabinet: @ Old PCB(s). ™ Game harness if it is not Japan Amusement Machinery Manufacturers Association (JAMMA)compatible, @ Control panel decals,labels, and controls, ™@ Side decals, graphics and adhesive. If the cabinet sides are damaged, repair them before putting on the new decals. ™@ Video display shield, display bezel, attraction shield, and marquee.
  • Wipe down and vacuum the cabinet. Paint the cabinet, if required.

Installing the Kit Parts

The kit parts are shown installed on a cabinet in Figure 1-4.

Installing the Pedal To install the pedals, you need a copy of the pedal installation template at the end of this chapter and the following parts from the kit: ™@ The pedals and pedal brackets @ Eight #10-24 x 1/2-inch-long pan-head screws, internal lock washers, and lock nuts @ Eight 1/4-20 x 1 1/2-inch-long carriage bolts, flat washers and lock nuts.

  • Take a pedal apart by removing the set screws on the sides of the hinge. Take out the hinge pin. Take the pedal top off. 2, Use the #10-24 pan-head screws to attach pedal bottom to the bracket. (See Figure 1-1.) Install the lock washers and lock nuts. Put the ground wire lug between a lock washer and a lock nut on one of these screws.
  • Put a drop of oil on the hinge pin. Reassemble the pedal.
  • Put the other pedal on its bracket.
  • Cut the copy of the pedal installation template apart. Put the pieces on the the cabinet according to the dimensions shown in Figure 1-2 and on the template. Installation

Drill the holes in the cabinet with a 5/16-inch drill bit.

NOTE If you have a cabinet with a recessed base, put the pedal template higher so you will not drill into the gussets in the corners. You will also have to drill two more holes through the cabinet floor to feed the pedal wires into the cabinet.
  • Feed the pedal harnesses through the center holes. Insert the 1 1/2-inch-long carriage bolts from the outside. Install the flat washers and lock nuts.

Installing the Control Panel To set up the Badlands control panel you need the following parts from the kit: ™ Black metal cover plate Control panel decal Two red and two blue buttons Four start/fire button collars Two steering assemblies Two steering assembly mounting plates Six #10-24 x 1-inch-long carriage bolts, flat washers, and lock nuts Six #1/4 flat washers and lock nuts.

  • Lay the black metal cover plate over the bare control panel. Line up the two center button holes on the metal cover plate with the two center button holes on the control panel. Screw two buttons in the two center holes. See Figure 1-3. (If your control panel does not have the two center button holes in the correct position, just center the metal cover plate on the control panel.)
  • Clamp the cover plate to the control panel with three C-clamps.
  • Drill six mounting holes for the cover plate through the control panel using a 3/16-inch drill bit.
  • Install enough of the carriage bolts and lock nuts in the mounting holes to hold the cover plate in place.
  • Using the cover plate as a template, cut the holes for the outer buttons with the 1 3/16-inch hole cutter. Drill three mounting holes for each steering assembly using a 5/16-inch drill bit. You may also need to drill holes for the steering harnesses.
  • Take the metal cover plate off the control panel. With the cover plate off, install the control panel
Page 10

Installation. Badlands Universal Kit

Set Screw (2 places)

Hinge Pin

‘@

#10 Lock Nut (4 places)

#10 Lock Washer (4

NOTE This shows the installa- [— | tion of the harness ground lug.

Flat Washer (4 places)

1/4"-20 Lock Nut (4 places)

1/4"-20 Carriage Bolt (A places)

#10-24 Pan-Hd Screw (4 places) MN : Pedal Bracket

Figure 1-1 Assembling the Pedal

Page 11

Badlands Universal Kit Installation

Use a 5/16" Dri Bit, 10 places

NOTE Use the template at the end of the chapter to install the peaals.

Figure 1-2 Installing the Pedals on the Game

decal on the control panel. Do not put the decal over the black cover plate. ; CAUTION ;

  • Now install the black cover plate on the control Tighten the nuts on the steering assembly panel with the carriage bolts, flat washers, and lock studs to 40 inch-pounds maximum. If you nuts. tighten the nuts too much, you can damage the assembly.
  • Install each steering assembly with a mounting plate on the underside of the control panel. Install the mounting plate so the steering assembly cannot be torn off the control panel.
  • Put the 1/4-20 lock nuts and flat washers on the studs. Do not use a ratchet or an air gun to
  • Install the buttons with a plastic “Start/Fire” collar under each button. Put the blue buttons on the left and red buttons on the right.

tighten the nuts.

CAUTION Install the steering mounting plates Black Metal under the control panel so the Cover steering assemblies cannot be torn Frnt sy off the control panel. (places) Steering Carriage Wheel Assy places) ‘© Places) “

Steering Assy Steering Assy Mounting Mounting Hames

Holes Holes Holes

(6 places) (2 places)

Control Panel J Blue Button Assy Snap-Action Switch Locknut a on (6 places) ces}

Blue Red

Red Button Hotes Button Holes

NOTE Button Assy (2 places) places) The steering wheels Snap-Action Switch ;

are rotated for clarity. baa a Detail of Black Metal Cover

Figure 1-3 Assembling the Control Panel

Page 12

Installation

Installing and Connecting the Harness Badlands Universal Kit

Table 1-3 JAMMA Wire Connections

STEERING C

CAUTION To.meet FCC requirements, install the split beads included in the kit over all the wires in the harness as close to the connector as possible.

1.

1-6 If your game does not already have a JAMMA harness, find the JAMMA harness (part no. A046501-

  • in the kit and install it. Using Table 1-3, JAMMA Pin and Wire Connections, for wiring information, connect the JAMMA harness to existing component harnessing. Use crimp splices or butt soldering.
WARNING Do not simply tie the wires together. If you do, you could cause intermittent problems, loose connections, oxidation, or a fire.

Connecting Power Wires

  • Connect the wires on the JAMMA harness to the wires for the power supply, as shown in Table 1-3. The Badlands kit requires +5V and +12V. If -5V is available, it should be used too. If -5V is not available, connect both wires to the 5 V RTN (GND) terminal on the power supply unless the power supply has 12V RTN. If it does, connect both wires to it.
Page 13

Badlands Universal Kit Jastallation

Notes to Table 1-3 Jamma Wire Connections

ae Twisted pair,

1. Connect four of the lise BN wires. to ‘the 5V RIN =

(GND) terminal'on the power supply unless the power ‘supply has'a 12V-RTN. If you have’a 12V20 _ RIN, connect one. of the wires to the Tay RIN “8. Connect to s the Ne (GND) terminal “2s Cofinect the comm

2. Three of the R wires go to the +5V. sent on the apo ORE of the BRIW wi

power supply- If the: power supply-has a #SENSE 9. Connect to the ‘terminal, connect one: of these three wires to the © switch. Connect __ +SENSE instead of the +5V. The fourth wire goes fo 2. switch to'one of the: the red wires on the steering assemblies, © : connect to the Ni Connect both wires to the -5V_ terminal of te : switches. Conn _ power supply. (if -5V is not available, connect both wires to the 5. V REN (GND) terminal on the power" supply unless the power supply has 12V RTN. If it does, contiect ‘both wires to. it. NOTE: If -5V is not _ | used, the maximum power to the pedi Er reaiiced ee _ by half) : SS : 4, Connect both wires to the +2 terminal of the "power supply. (If your coin counter(s):require(s) _ | 12V,: you ‘can use one of these two wires for os ed _ side of the coin counter(s).) :

Connect to the negative side of the coin’ MES) Note 2, above. Note: Do not use Ay soot

If your counter(s) require 5V, splice’ into the ‘redwire that brings +5V to the steering assemblies. See

  • ‘Attach to. the: video display. a . s z | Use this wire if you \ want an external ‘self-test switch: The Badlands: kit already has’ a‘ self-test “switch on the PCB. If you connect’ ai’ external self.” ') lest switch, first make ‘sure ‘the ‘switch ‘on the PCB is. bat

wire te the common ten

  • Connect the thir “the control switche MON ‘encais of wire .

Connect the brown wire

speaker and the white:

If your original game used other voltages, they are Connecting Coin Door Wires not needed. Tie off any unused wires on the 1, Connect the wires on the JAMMA harness to the power supply. coin switches and meter according to Table 1-3.

  • There is more than one wire for each voltage. Use 2. Connect one side of the door lamps to one of the more than one wire for each voltage (connecting BK/W wires. Connect the other side of the door them as described in Table 1-3) so that you do not lamps to the R wire supplying +5V to the joysticks. overload the edge connector and cause it to burn. Connecting Video Display Wires NOTE Do not use -5V for the coin door lamps.
NOTE -5V is required for audio. The JAMMA harness provides only nega- (Some games have separate power supply outputs tive composite sync. If your video display for the coin door lamps. If you choose to use these requires separate positive sync, see outputs, make sure you connect both sides of the Chapter 3 for alternative wiring. lamps to the terminals on the power supply.)

Connect the wires designated for the red, green and Connecting the Control Wires

biue video guns along with the sync and ground wires, Connect the steering assembly harnesses and the butaccording to Table 1-3. ton harnesses to the JAMMA harness according to the information in Table 1-3

Page 14

Installation Badlands Universal Kit

Attraction Shield

Display Bezel Attraction Film

Game PCB Assembly Display Shield : Stand-ofts 4 X-Rec Screw

Volume Control

Self-Test Switch

Control Panel Decal Blue Button Assy Shap Action Switch Start/Fire Collar Locknut

Red Button Assy Snap Action Switch ‘Start/Fire Collar Control panel in closed position Self-Test Label

Foot Pedal

NOTE The steering wheels are shown rotated for clarity.

Figure 1-4 Badlands Kit Parts Installed in a Cabinet

1-8 HH]

Page 15

Badlands Universal Kit

Grounding the Cabinet Find the ground lead (green) of the 115V input power line. Connect this lead in daisy-chain fashion to a bare metal part of the coin door, both pedals, the control panel, the video display, and the power supply. This is a safety requirement for the players’ protection. This AC ground must be of #18 AWG wire or larger.

Checking the JAMMA Connections Before plugging in the game PCB, turn on the power to the game, and check +5 Volts on pins 3, 4, C, and D of the JAMMA connector; +12 Volts on pins F and 6; and -5 Volts on pins E and 5. Check that the video display and the attraction lamp have power. Now turn off the power to the game,

Installing the Badlands Printed-Circuit Board

  • After you have checked the power on the JAMMA connector, above, install the Badlands game PCB in the cabinet. Use the nylon standoffs and four #6-32 screws in the kit.
  • Connect the JAMMA connector to the PCB.
  • Turn on the power to the game. Check that the game PCB functions. If a video picture is not present, see Chapter 3.

Installing the Display Bezel Find the cardboard display bezel (part no. 047463-01). Measure the size of the existing display bezel and cut the new display bezel to size, if necessary.

Installing the Product ID and FCC Label Place the product ID label (part no. 038158-01) and FCC label (part no. 039450-01) on the back of the cabinet.

Installing the Side Panel Decals Find the side panel decals. Wet the left and right side panels of the cabinet with slightly soapy water. Then position the decals as shown in Figure 1-4. Remove any wrinkles in the artwork using a squeegee. Allow the sides to dry.

Installing the Attraction Assembly Find the attraction shield and the attraction film. Using the existing shield as a template, cut the shield and film to size, if necessary. Install them on the cabinet as shown in Figure 1-4,

Testing After Power-Up

Use the self-test to check the operation of the game. Refer to Chapter 2 for information about the self-test. Installation

Perform the self-test when you first set up the game, each time you collect the money, or when you suspect game failure.

Setting the Coin and Game Options

The Badlands coin and game options are set in the self-test. See Chapter 2 for information about the option settings.

Game Play

This section of the manual describes the theme of the Badlands game and the game play features.

Introduction It has been 50 years since the nuclear disaster. The sport of sprint racing is now a ruthless battle between armed cars. These races take place on tracks built in the ruins of the dangerous nuclear zone known only as the BADLANDS. This is sprint racing gone BAD! It’s all-out war on the track as players blast away at the drones (and each other) to finish first! Players shoot playfield targets for extra points and bonus missiles!

One or two players can race at any time with Badlands’ buy-in and game continuation features. If a player loses to one of the drone cars, the player can put in another coin to continue on to the next heat and retain any custom car options he has acquired. Each race has four laps. Players continue on to the next racing heat as long as they beat the drone car. Badlands has eight unique track layouts set in eight different animated backgrounds that react to player shots and crashes. These backgrounds change with the level of difficulty. The backgrounds are: The City—watch out for falling power lines and the water tower that crashes, spilling water on the track that slows you down. ™ The Desert—the mountain rumbles and falls onto the track.

The Freeway—make your own shortcuts through the diner and gas station. ™ = The Volcano—lava spills down upon the track. ™ The Junkyard—power lines fal] and old cars explode on impact. The Military Base—cannons fire and missiles explode.

Page 16

Installation

™ The Prison Yard—Use the gates to make shortcuts and avoid the towers that fire upon you.

m The Refinery—be careful of creating oil spills. Players can add coins to quickly customize their car. Custom car options include: ™ Missiles to destroy other cars and walls to make short cuts.

1-10 Badlands Universal Kit

Tires to slide less around the turns.

Turbo to get up to speed faster. Speed for higher top speed. Shields to protect the car from shots, missiles and crashing.

THIN

ITT

Page 17

Chapter 2

Self-Test

The Badlands™ game tests itself

and provides visual and audible

indications of the condition of the

game circuitry and controls. Self-

test information is displayed on the screen and

through the sound system. No additional equipment is

required. Perform the self-test when you first set up

the game, each time you collect the money, and when you suspect game failure. The

self-test screens provide informa-

tion pertaining to the game cir-

cuits and controls. This chapter

shows the screens in the self-test and explains each of

the tests. The screens and explanations are arranged in

the order they appear in the self-test, Table 2-1 lists all

the self-test screens and their purposes.

Page 18

Self-Test

Badlands Universal Kit

Table 2 2-1 Summary of the Self-Test Screens

ie Color Purity Screen White Color Purity Scrée! lor Purity :

Sound Test Screen

mechanism operation

Entering and Exiting the

To enter the self-test, turn on the self-test switch, located on the game PCB at 19B near the JAMMA connector. If you turn on the self-test switch after the power is turned on, the self-test skips the RAM and ROM test. To test the RAMs and ROMs, first turn on the self-test switch and then turn on the power. Turn off the self-test switch to exit the self-test and return to the Attract Mode. However, if you want to reset the coin or game options, leave the options screen and then turn off the self-test switch. If you turn off the self-test switch while you are on the options screen, the settings will not change.

RAM and ROM Test

Test the RAMs and ROMs by turning on the self-test switch first, and then the power switch. If the power was on when you turn on the self-test switch the RAM and ROM test is skipped. If the RAMs and ROMs pass

2-2 the test, the display advances to the self-test menu screen automatically.

Testing Game RAMs No message appears while the test is checking the RAMs. If the game has a bad RAM, you may see a message, or if the problem is severe, you may only see a colored screen. See Table 2-2 for the location of the bad RAM if you see a message. If the test finds no RAM errors, no message appears and the program goes to the ROM test after a 4-second delay. The RAM test continues to run until it passes. You can advance to the next RAM or ROM test by pressing the left player Start/Fire button.

Table 2-2 Bad RAM Locations

Page 19

Badlands Universal Kit

Testing Game ROMs If the ROMs have no errors, the ROM test displays no messages and advances to the Statistics screen. If a ROM fails, a message is displayed. If the game has an error in the program ROM, then the error number is shown at the bottom of the screen. See Table 2-3 for the location of the bad ROM.

Table 2-3 Bad Upper or Lower Main

ROM Locations

Error Address _ Location on Game PCB ‘00000 “-U=20F L=27F? 20000 “USI7E SUF

If you think you have a ROM error, but the screen shows no messages, see Table 3-3 for information about the locations of various ROM functions. Depending on how bad the ROM error is, you may not be able to go to the self-test menu by pressing the left player Start/Fire button. If you have more than one ROM error, you must press the left player Start/Fire button several times to go to the self-test menu.

Self-Test Menu

Choose the screen you want to see from this menu, shown in Figure 2-1. Move through the menu by turning the left steering wheel. To choose a screen, press the left player Start/Fire button.

SELF-TEST +O SELECT: USE LEFT WHEEL TO EXECUTE: PRESS LEFT START

GAME STATS AND HISTOGRAM ‘COIN OPTIONS GAME OPTIONS INPUT TEST PLAYFIELD STAMP TEST. MOTION OBJECT TEST MOTION OBJECT PICTURES PLAYFIELD PATTERN TESTS: (CONVERGENCE PATTERN). COLORBARS AND PURITY TESTS. SOUND TEST

Figure 2-1 Self-Test Menu Screen

Statistics

The statistics screen is shown in Figure 2-2. The statistics information is accumulated either from the first time the game was turned on or from the last time the Seif-Test

STATISTICS

iE SSION: FOTAL GAMES. ERROR COUN: TOTAL GAME TIME TOTAL CREDITS: ave a iMpencorr AVG TIMEG AM ANG EANESISESSION TO EXIT: PRESS LEFT 5’ 70 CLEAR STATISTICS: wa HELE: SPINNING A WHEEL PRESS RIGHT: START ‘OS CREATION DATE 21 NOV 89 PG CREATION DATE 04 JAN 70 16:08:00 00:00:00.

Figure 2-2 Statistics Screen

statistics were reset. To reset the statistics information, spin either steering wheel and while the wheel is spinning, press the right player Start/Fire button. Enter the information on the statistics screen on a copy of the statistics page in the back of this manual. The following information appears on the statistics screen: Left Coins shows the number of coins deposited in the left coin mechanism. Right Coins shows the number of coins deposited in the right coin mechanism. = Continues shows the number of times players coi tinued their games. ™ Conversions shows the number of times players converted credits to wrenches. (The Convert Credits to Wrenches game options setting must be set to yes.) ™ 0 Plyr Mins shows the minutes of idle time. ™ 1 Plyr Mins shows the minutes played as a 1-player game. ™ 2 Plyr Mins shows the minutes played as a 2-player game. m@ Sessions shows the number of sessions played. One session is the game play starting at the left or right player position and play ending at that position, regardless of the number of coins or time played. ™ Total Games shows the total number of games played. One “game” is the time between a player starting and that player losing to a drone car. @ Error Count shows the number of EEROM errors that were detected. If this is any number other than zero, all of the statistics may be wrong. If you have errors counted regularly, replace the EEROM at

Page 20

Self-Test Badlands Universal Kit

location 27J on the Game PCB. togram, spin either steering wheel and while the m Total Game Time shows the total time, in minutes, wheel is spinning, press the right player Start/Fire butthat the game has been played. =m Press the left player Start/Fire button to go to the selftest menu screen.

Coin Options

The coin options screen is shown in Figure 2-4. The coin options screen indicates the current coin option settings and allows you to change those settings. ™ Total Credits shows the total number of credits deposited in both coin mechanisms. ™ Avg Time/Credit shows the average game time per credit, in seconds, for all players. ™ Avg Time/Game shows the average game time per game, in seconds, for all players. The coin mode does not affect this figure, nor do credits converted to wrenches. The settings, with defaults, are shown in Table 2-4.

To move through the options, turn the left wheel. The blue box around the option name indicates the option

COIN OPTIONS:

NOTE Game time for Badlands will average about 3 1/2 minutes per game because of the nature of the game play.

m Avg Games/Session shows the average number of games played in a session. This indicates continued games. Press the left player Start/Fire button to go to the his- {DEFAULTS IN GREEN} COIN MODE 4+ COIN 1 CREDIT RIGHT MECH MULTIPLIER 1 COIN COUNTS AS 1 COIN LEFT MECH MULTIPLIER 1 COIN COUNTS AS 1 GOIN. BONUS ADDER NO BONUS ADDER togram screen.

Histogram

The histogram screen is shown in Figure 2-3. The histogram shows the average game time from 0 to 600 or more seconds. The histogram also provides a corresponding bar graph. To change OPTION: use LEFT Wheel ‘To change SETTING: use RIGHT Wheel To SAVE and EXIT: press LEFT Start ‘To ABORT: press RIGHT Start

Figure 2-4 Coin Options Screen Enter the information on the histogram screen on a copy of the statistics page in the back of this manual.

The game times information is accumulated either from the first time the game was turned on or from the last time the game times were reset. To reset the his- Table 2-4 Coin Options Settings

HISTOGRAM 4 GAME TIME IN SECONDS:

70-599 600 & UP TO EXIT: PRESS LEFT START. TO CLEAR HISTOGRAM: WHILE SPINNING A WHEEL PRESS RIGHT START

Figure 2-3 Histogram Screen

2-4

Page 21

Badlands Universal Kit

that can be changed. The default setting appears in green letters. To move through the settings, turn the right wheel. To save the settings and exit the screen, press the left Start/Fire button. To leave the screen without saving the settings, press the right Start/Fire button. ™ Coin Mode is the number of coins required for one credit. Coin Mode should have a blue box around it when you enter this screen. m@ Right Mech Multiplier is the number of coins each coin counts as in the coin mechanisms. = Left Mech Multiplier is the number of coins each coin counts as in the coin mechanisms. ™ Bonus Adder lets you choose bonus coins, no bonus, or free play. If you replace the EEROM at location 27J or if a hardware problem occurs, the coin options will change to the default (green) settings.

NOTE To save new coin option settings, first exit the screen by pressing the left Start/Fire button and then turn off the self-test switch.

Game Options

The game options screen is shown in Figure 2-5. This screen indicates the current game option settings, and is used to reset the high score table and change the game option settings. Refer to Table 2-5 for the available settings and Atari Games’ recommended settings. To move through the options, turn the left wheel. The blue box around the option name indicates the option

GAME OPTIONS (DEFAULTS IN GREEN) RESTORE FACTORY OPTIONS AD: SPECIAL COST 410 special cost: DIFFICULTY LEVEL. moderate aoe ‘GREDITS TO: WRENCHES

music IN ATTRACT MODE

Lean HIGH SCORE TABLE

oy MORE WY ‘To change OPTIONS: use LEFT Wheel To change SETTING: use RIGHT Wheet To SAVE alid EXIT: press LEET Start Ta ABORT: press RIGHT Start

Figure 2-5 Game Options Screen Self-Test

Table 2-5 Game Options Settings

= Two Credits to Start; (One fo Continue e “Moderate +

  • Hardest No No Nee No (No.

that can be changed. The default setting appears in green letters. To move through the settings, turn the right wheel. To save the settings and exit the screen, press the left Start/Fire button. To leave the screen without saving the settings, press the right Start/Fire button. m™ Restore Factory Options lets you set all the game options to the factory options or lets you use your own settings. Make sure you set this to no to use your own chosen settings. @ Special Cost lets you choose two credits to start and one to continue, or no special cost, which is one credit to start and one to continue. @ Difficulty Level lets you choose the difficulty level of the Badlands game. ™ Convert Credits to Wrenches controls whether players may convert credits to wrenches. Music in Attract Mode lets you turn the music on or off in the attract mode. ™ Clear High Score Table resets the high score table if you select Yes. m™ Auto High-Score-Table Reset automatically resets the high-score table after 2000 games if no player has achieved a high score in the last 200 games. m Don’t Do Drugs lets you turn off or on the FBI symbol screen in the attract mode.

NOTE To save new game option settings, first exit the screen by pressing the left Start/Fire button and then turn off the selftest switch.
Page 22

Self-Test

Input Test

The input test screen, shown in Figure 2-6, checks the player controls. The inputs that are checked are: ™ Switches and Lev/Edge are for Atari Games development, ™ Leia Values, Raw and Delta are the inputs for the steering wheels and the pedals. ™ Left Wheel Delta value increases from 01, as you turn the wheel clockwise. The faster you turn the wheel, the higher the delta number is. As you turn the wheel counterclockwise faster and faster, the value decreases from FF. | Right Wheel Delta value increases from 01, as you turn the wheel clockwise. The faster you turn the wheei, the higher the delta number is. As you turn the wheel counterclockwise faster and faster, the value decreases from FF. m Left Pedal Delta value increases when you press the left pedal. ™ Right Pedal Delta value increases when you press the right pedal. lm Self-Test shouid have a pink box around it when this screen appears. ™ VBLANK is for Atari Games development. =| Right Stari/Fire tests the right Fire/Start buttons. Press either of the right buttons and a pink box appears around the words. @ Left Start/Fire tests the left Fire/Start buttons. Press either of the left buttons and a pink box appears around the words. ™ Freeze, Freeze-Step, Old Gas Pedals, and Old Steering Wheels should never be highlighted. Simultaneously press the right and left player Start/Fire

INPUT TEST SWITCHES RaW LETA VALUES cau DELTA 00 Left wheel LEVEDCE 00 Right Wheel 82°00 00 Left Pedat 00 Right Pedal

NI RIGHT START/FIRE LEFT START/FIRE FREEZE FREEZE-STEP: OLD GAS PEDALS OLD STEERING WHEELS

TO EXIT: PRESS BOTH START BUTTONS.

Figure 2-6 Input Test Screen Badlands Universal Kit

button to return to the self-test menu screen.

Playfield Stamp Test

This screen shows the different stamps used in the game and appears in Figure 2-7. If you turn the left wheel clockwise, you will see Bank 0 stamps. If you turn the left wheel counterclockwise, you will see Bank 1 stamps. Simultaneously press the right and left player Start/Fire button to return to the self-test menu screen.

Motion Object Test

The motion object test screen is shown in Figure 2-8. The motion object test indicates the condition of the motion-object buffer circuit. Use the controls to test the motion objects as described in Table 2-6. Table 2-6 Motion Object Test

Page 23

Badlands Universal Kit

Motion objects with priority 0 (PRI: 0) move behind the orange and grey vertical stripes on the sides of the screen. Motion objects with priority 1 move in front of the stripes. The following information is provided at the bottom of the screen: ™@ MOB indicates the number of the motion object selected. @ PiX indicates the stamp number in ROM. HPOS indicates the horizontal position of the object. VPOS indicates the vertical position of the object. VSIZ indicate the number of stamps. PAL indicates the palette number for colors. PRI indicates priority. Simultaneously press the left and right Start/Fire buttons to return to the self-test menu screen.

Figure 2-8 Motion Object Test Screen

Motion Object Picture Test

The motion object picture test checks the information in the EPROMs in the game and is shown in Figure 2-

  • Press the right Fire/Start button to see the next picture and press the left Fire/Start button to see the previous picture. To change the palette, press a pedal.

Table 2-7 Motion Object Picture Self-Test

ais: Drees pedals

Figure 2-9 Motion Object Picture Test Screen

View the pictures, and if you think there are errors (other than unusual colors) check the EPROMs as shown in Table 2-7. Simultaneously press the left and right Start/Fire buttons to return to the self-test menu screen.

Playfield and Convergence

Pattern Test

The first playfield and convergence pattern screen is shown in Figure 2-10. This test indicates the condition of the display size, centering, linearity, and convergence. The grid pattern should be white. Press the right player Start/Fire button and the grid pattern changes to violet. Pressing the right player Start/Fire button again should cause the grid pattern to turn green. Check the grid pattern for the following characteristics (the violet and white patterns‘are used

Figure 2-10 Playfield and Convergence Pattern Test Screen

2-7

Page 24

Self-Test

to adjust the display convergence): ™ Grid lines should show no pincushioning or barreling, and the lines should be straight within 3.0 mm. ™ Violet and white pattern convergence should be within 2.0 mm. If the display characteristics are not within these limits, refer to the display manual for the linearity and convergence adjustment procedures or to determine the possible cause of failure. If you press the left player Start/Fire button you will see a variety of patterns. Simultaneously press the left and right Start/Fire buttons to return to the self-test menu screen.

Color Bars and

Color Purity Test

The color bars and color purity test screen is shown in Figure 2-11. This test indicates the condition of the display color circuits.

Figure 2-11 Color Bars Test Screen

The screen should show, from top to bottom, a row of red, a row of green, a row of blue and a row of grey, each with 32 vertical bars. The brightest bars should be on the left and darkest (black) on the right, with a grey frame around the screen. If the display characteristics are not correct, refer to the video display manual for the color-gun adjustment procedure or to determine the possible cause of failure. If you press the right player Start/Fire button, you will see a screen with color bars of yellow, cyan, magenta, and grey. Press the right player Start/Fire button again to see the color purity screens of red, green, blue, white and

2-8 Badlands Universal Kit

grey. These screens show the adjustment of the color purity of the video display. Each screen should display a rectangle of color, with no curving at the corners, no unevenness of color, and no lines in the display. If the screens are not correct, adjust the video display as described in the video display manual. Simultaneously press the left and right Start/Fire buttons to return to the self-test menu screen.

Sound Test

‘The sound test screen is shown in Figure 2-12. This test indicates the condition of the coin mechanisms and the music and sound-effects circuits.

SOUND 4 MUSIC CHIP TEST

NUMBER OF SOUNDS. 73. GOOD LEFT RIGHT. o oO SOUND CPU STATUS = COIN MECH SWITCHES:

TO SELECT. SOUND: USE RIGHT WHEEL TO PLAY: RHT START, TO STOP: LET START TQ EXIT: PRESS BOTH START BUTTONS

Figure 2-12 Sound Test Screen

The sound microprocessor is reset at the beginning of this test. The game may take up to three seconds to produce the first sound. If the sound-microprocessor reset fails, the message SOUND PROCESSOR NOT RESPONDING should blink. If the sound microprocessor is good, check the coin mechanisms and the sound microprocessor circuits by observing the following messages: m 1,2,3,4, etc. are the numbers assigned to each sound. Choose a sound by turning the right wheel Some sounds numbers cannot be selected. To hear the sound, press the left player right Start/Fire button one or more times. Press the left player Start/Fire button to silence the sound. m 4 Music Chip Test consists of eight tones in a major scale that alternate between sound channels (16 tones in all). m Number of Sounds indicate the number of sounds used in the Badlands game.

Page 25

Badlands Universal Kit Self-Test

Table 2-8 Faulty Sound RAM and ROM Locations _ Error Message _ ‘Music Chip Time Out Sound CPU Interrupt Error

Sound CPU RAM 1 Err

Sound CPU ROM 1 Error

‘Communications Error #1 Counts the number | Sound Processor Not Responding further. Press both Stait/Fire |

major problem: swith th

m Sound CPU Status indicates the condition of the sound microprocessor. If the sound microprocessor is good, the word GOOD should appear. If the sound microprocessor or associated circuitry is faulty, a number will appear (to indicate sound status) as well as an error message. See Table 2-7 for the error messages and faulty sound RAM and ROM locations. Coin Mech Switches shows the condition of the left and right coin mechanisms. The zeroes underneath left and right correspond to the left and right coin mechanisms. The zero should change to one when the coin switch is held down, and change back to zero when it is released. Simultaneously press the left and right Start/Fire buttons to return to the self-test menu screen.

2-9

Page 26

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 27

Chapter 3

Troubleshooting and Maintenance

This chapter contains regular of ROM-caused problems with

maintenance information, trou- specific ROMs to check and

bleshooting tables, and repair replace. The last part of the chap-

procedures for your Badlands ter has information about con-

game. The chapter has two parts. necting the video display to the

The first part contains three trou- Badlands kit and repair informa-

bleshooting tables. The first table has general trouble- tion for the steering assembly and the pedal assembly.

shooting information, the second contains the voltage If a part is mentioned, but not illustrated, see Chapter

levels and test points on the PCBs, and the last table is 4, Illustrated Parts Lists, for information.

Page 28

Troubleshooting and Maintenance

Table 3-1 Troubleshooting Table Badlands Universal Kit

Sound Problems Is the spules volome ‘turned ub ee : Is the voltage on the JAMMA ‘connector correc . Is the harness from the PCB to the speake ls the audio ROM and RAM good?: ae Check the’ ROM and RAM in the _o Bad Sound RAM and ROM Locatio b: Check the ROM at 9C. 5, Is the the voltage level to the

  • oe the ee fees to be replaced? Erratic sound Video Display Proble: Sync Problems .
  • Is the oe In _ 3. Are the: connections good:

. Is the line fuse good?

VAC, depending on the type of video displ

the level i is not correct, ch |

3-2

Page 29

Badlands Universal Kit Troubleshooting and Maintenance

Table 3-1 Troubleshooting Table, Continued. 83 deiss < se Action ee

i cted to the monitor?

Are the sync inputs connected properly? Does your sync? See the Video Display Sync Problems sect

3-3

Page 30

Troubleshooting and Maintenance

Video Display

Sync Problems Some video displays cannot use the composite negative sync that is on the JAMMA connector. If you need separate positive sync the Badlands game PCB includes a standard Atari video connector (located at 14A) that provides separate positive sync. Refer to Table 3-4 and make the appropriate connections for your video display. Table 3-4 Atari Video Connector Pin Assignments for Separate Positive Sync

Horizontal Shifting If you cannot center the display horizontally as described in your video display manual, you can shift it horizontally by altering the game PCB. 1, Remove the resistor at R98.

  • To shift the display to the right, add a resistor of less than 100 Q (or a wire) at location R99. To shift the display to the left, add a resistor of less than 100 Q (or a wire) at location R100.

Steering Assembly

Replacing the Steering Wheel

It is easier to replace the steering wheel if you remove the steering assembly from the control panel.

  • Open the control panel. :
  • Unscrew the nuts that hold the steering assembly on the control panel. Remove the reinforcing plate.
  • Take off the connector to the PCB. Remove the steering assembly from the cabinet: 4, The screws that hold the steering wheel on the steering assembly are tightened to.90 inch-pounds, and are difficult to remove. One way to loosen the screws is to put the tamper-proof hex key in a vise, put the screw head into the key, and turn the steer-

3-4 Badlands Universal Kit

ing wheel until the screw is loosened. Loosen and remove all the screws.

  • Replace the steering wheel. Replace the screws. Tighten to 90 inch-pounds,
  • Install the steering assembly on the control panel. Install the nuts on the studs. Tighten these nuts to 40 inch-pounds maximum. If you tighten the nuts too much, you can damage the steering assembly and the steering wheel will not turn easily.

Replacing the Steering PCB The steering wheel assembly is shown in Figure 3-1.

  • Open the control panel.
  • Unscrew the nuts that hold the steering assembly on the control panel. Remove the reinforcing plate.
  • Take off the connector to the PCB. Remove the steering assembly. 4, Remove the two cross-recessed screws that hold the PCB bracket on the steering housing. Remove the bracket and the PCB.
  • Take the old PCB off the bracket. Repair or replace it. (The schematic for the PCB is in Chapter 5 of this manual.) Install the repaired or new PCB on the bracket.
  • Put the PCB and the bracket into the steering housing. Make sure the encoder wheel, inside the housing, fits between the two parts of the sensor on the board and does not scrape against the sensor.
  • Put the screws and the washers into the PCB and attach the PCB to the housing.
  • Install the steering assembly on the control panel. Install the nuts on the studs. Tighten these nuts to 40 inch-pounds maximum. If you tighten the nuts too much, you can damage the steering assembly and the steering wheel will not turn easily.

Pedal Assembly

The only parts of the pedal assembly you can replace separately are the set screws on the hinge (part number 75-4504) and the pedal tread (part number 047518- 01). You must purchase the rest of the pedal as an assembly because special techniques are required to assemble it at the factory.

Page 31

Badlands Universal Kit

72-1605S 78-40104 : 6-32 Pan-Hd Screw Steering Wheel (2 places)

175014-1026 A047368-01 138000-001 #6 Flat Washer P.C. Board Opto-Serrvar (2 places) Assy

176025-4412 1/4-20 Button-Head Tamper Proot Screw 75-0553 1/4 Internal Lock-Washer

046655-01 Cover Plate 79-58356 Connector

110027-151 150, 1/8 W Resistor

047513-01 Encoder Wheel 75-0448 Split Look Waste 72-8406 +#4-40 Screw

175014-1018 #4 Flat Washer Troubleshooting and Maintenance

72-1605S 6-32 Pan-Hd Screw 175014-1026 047503-01 #6 Flat Washer Housing

047505-01 PCB Bracket

178012-001 Clip Ring 047508-01 Shim

Figure 3-1 Maintaining the Steering Assembly

3-5

Page 32

Chapter 4

Illustrated Parts Lists

This chapter provides information

you need to order parts for your

game. Common hardware parts,

such as screws, nuts, washers, and so on usually are

not listed in the parts lists. The parts lists (except for

the PCB parts lists) are arranged alphanumerically by

Atari part number. All A-prefix numbers, which are

assemblies, come first. Next are part numbers with six

numbers followed by a hyphen (000598- through

201000-). Ending the list are part numbers with a two-

number designation followed by a hyphen (00through 99-). The PCB parts lists

are arranged in alphabetical order

by component. Within each sec-

tion the parts are arranged numerically by part num-

ber. When you order parts, give the part number, part

name, the number of this manual, and the serial

number of your game. With this information, we can

fill your order rapidly and correctly. We hope this will

create less downtime and more profit from your

games. Atari Games Customer Service phone numbers

are listed on the inside front cover of this manual.

Page 33

Illustrated Parts Lists Badlands Universal Kit

Table 4-1 Badlands Kit Parts List A047460-01 C

Part No.DescriptionPart No.Description
A047193-01Badlands Game PCB Assembly141026-001Ferrite Split Bead
A046501-01JAMMA Harness Assembly160044-001Snap-Action Microswitch
A047502-01Steering Assembly (assembled at the factory177010-240#10-24 Polymer Hex Locknut
with JS Hamess Assembly part no.177010-244—-#1/4-20 Polymer Hex Locknut

A047138-01)

4047507-02Pedal Assembly. Replaceable Parts:178032-002Wire Tie Wrap
75-45041/4-20 x 1/4-Inch Long Hex Socket Set178126-0025/32 Tamperproof Hex Key
Screw178237-001Red Button Assembly
047518-01Pedal Tread178237-005Blue Button Assembly
047461-01Black Metal Control Panel Cover Plate178265-001Nylon PCB Standoff
047512-01Reinforcing Plate for Steering Assembly178283-001Start/Fire Identification Collar
047509-01Pedal Mounting Bracket72-6612#6-32 x 3/4-Inch Pan-Head Screw
047205-01Attraction Shield72-1108F#10-24 x 1/2-Inch-Long Pan-Head Screw
047464-01Attraction Film175014-1040#10 Flat Washer
047463-0119” Display Bezel175014-10501/4 Flat Washer
047462-01Control Panel Decal75-050#10 Internal Lock Washer
047106-02Badlands Poster75-5116B#10-24 x 1-Inch-Long Black Carriage Bolt
047106-01Side Panel Decal75-5520B1/4-20 x 1 1/4-Inch-Long Black Carriage
038158-01Product 1.D. LabelBolt
039450-01FCC Compliance LabelTM-344Badlands Universal Kit Installation Manual
Page 34

Badlands Universal Kit

7216058 78-40105 “ 6-32 Pan-Hd Screw Steering Wheel (2 places)

175014-1026 A047368-01 138000-001 #6 Flat Washer P.C. Board Opto-Sensor (2 places) Assy

176025-4412 1/4-20 Button-Head Tamper Proof Screw 75-0553 1/4 Internal Lock-Washer

046655-01 Cover Plate 79-58356 Illustrated Parts Lists

‘72-1605 6-32 Pan-Hd Screw 175014-1026 047503-01 #6 Flat Washer Housing

047514-01 Hub 178012-001 75-4006 Clip Ring 047513-01 Set Si 508-01 Encoder Wheel onrene 75-0448 Split Lock Washer 72-8406 #4-40 Screw 175014-1018 #4 Flat Washer

Figure 4-1 Steering Assembly A047502-01 B

Steering Assembly Parts List

Part No.DescriptionPart No.Description
A047367-01P.C. Board Assembly, Replaceable Parts:176025-4412—1/4-20 x 3/4-Inch-Long Tamper-Proof
110027-1511502, 1/8 W ResistorButton-Head Screw
138000-001Opto-Sensor178012-0013/4-Inch Diameter Klip Ring
79-58356Connector72-1605S#6-32 x 5/16-Inch-Long Pan-Head Screw

72-8406 #4-40 x 3/8-Inch-Long Cap Screw 046655-01 Cover Plate

047503-01Steering Housing175014-1018#4 Flat Washer
047504-01Steering Shaft175014-1026#6 Flat Washer
047505-01Steering Bracket75-044#4 Split Lock Washer

75-055B 1/4 Black Internal Lock Washer 047508-01 3/4-Inch Shaft Spacer Shim

047513-01Encoder Wheel75-4006#10-32 x 3/8-Inch-Long Set Screw
04751401Encoder Hub78-40104Steering Wheel
Page 35

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 36

Badlands Universal Kit Illustrated Parts Lists

Badlands Game PCB Assembly Parts List

Designation.DescriptionPart No.DesignationDescriptionPart No.
Integrated Circuits16CIntegrated Circuit, 7418240137251-001
1KIntegrated Circuit, 74HCT273137655-00116PIntegrated Circuit, 74F00137327-001
2EIntegrated Circuit, LM324137582-00116SIntegrated Circuit, GALI6V8136074-1003
zyIntegrated Circuit, 74F260137570-00117EIntegrated Circuit, EPROM, 250 nsec 136074-1009
2NIntegrated Circuit, OTP, 250 nsec:136074-1013
17Integrated Circuit, 74F32137486-001
2sIntegrated Circuit, OTP, 250 nsec36074-101517KIntegrated Circuit, 7418175137123-001
2UIntegrated Circuit, OTP, 250 nsec36074-101717UIntegrated Circuit, VMATCH137552-001
3KIntegrated Circuit, 7418374137144-00118CIntegrated Circuit, 7418244137038-001
4Integrated Circuit, 74F260137570-001

18R, 18S Integrated Circuit, 74F74 137436-001

4NIntegrated Circuit, OTP, 250 nsec—_-136074-101219Integrated Circuit, 741808137012-001
4sIntegrated Circuit, OTP, 250 nsec—_-136074-101419KIntegrated Circuit, 7418240137251-001
4UIntegrated Circuit, OTP, 250 nsec—_-136074-101619NIntegrated Circuit, 7418374137144-001
SEIntegrated Circuit, LM324137582-001
20CIntegrated Circuit, LETA137304-2002
5KIntegrated Circuit, 74HCT273137655-00120FIntegrated Circuit, EPROM, 250 nsec 136074-1008
6FIntegrated Circuit, 7406137052-00121RIntegrated Circuit, GAL16V8136074-1002
JNIntegrated Circuit, 741S374137144-00121TIntegrated Circuit, 74F157137494-001
7R,7TIntegrated Circuit, 74F374137420-001

228 Integrated Circuit, 68000, 8 MHz, — 137289-003

WVIntegrated Circuit, 741$374137144-001PLAS
8EIntegrated Circuit, YM3012137402-001225Integrated Circuit, 74F74137436-001
8FIntegrated Circuit, 7418245137134-00122KIntegrated Circuit, 7418374137144-001
3Integrated Circuit, 74F00137327-00122NIntegrated Circuit, 7418257137136-001
8KIntegrated Circuit, RAM, 2K x137534-00122VIntegrated Circuit, RAM, 8KX8,137535-004

8, 35 nsec 100 ns

9BIntegrated Circuit, RAM, 8K x8,137535-00523RIntegrated Circuit, 74F74137436-001
120 nsec237Integrated Circuit, 74F157137494-001
9cIntegrated Circuit, OTP, 250 nsec:136074-101824Integrated Circuit, 7415138137177-001
9DIntegrated Circuit, YM2151137401-001

24F Integrated Circuit, EPROM, 250 nsec 136074-1007

ONIntegrated Circuit, GALI6V8136074-100424JIntegrated Circuit, 74F20137530-001
ovIntegrated Circuit, 7418374137144-00125MIntegrated Circuit, SOS137550-001
10EIntegrated Circuit, 7418174137122-00126Integrated Circuit, IM556, Dual137660-001
10FIntegrated Circuit, 74LS138137177-001Timer
10)Integrated Circuit, 74F04137437-00126CIntegrated Circuit, GAL16V8136074-1001
10KIntegrated Circuit, 74F374137420-00126RIntegrated Circuit, GAL16V8136074-2000
10RIntegrated Circuit, OTP, 250 nsec136074-101126TIntegrated Circuit, 74F153137492-001
VvIntegrated Circuit, 7418175137123-00126UIntegrated Circuit, 74F04137437-001
12EIntegrated Circuit, GAL16V8136074-100527FIntegrated Circuit, EPROM, 250 nsec 136074-1006
13FIntegrated Circuit, 741$374137144-001ayIntegrated Circuit, EEPROM,137399-300
13)Integrated Circuit, 74F00137327-0012816 A, 300 ns
13VIntegrated Circuit, 741S175137123-00128AIntegrated Circuit, 7418197137240-001
281Integrated Circuit, 741$257137136-001
14Integrated Circuit, 6502 A137577-001
14EIntegrated Circuit, 74F74137436-00128NIntegrated Circuit, 74F373137575-001
14RIntegrated Circuit, OTP, 250 nsec—_-136074-101028RIntegrated Circuit, 7415163 A137114-001
15FIntegrated Circuit, 7418374137144-00128TIntegrated Circuit, 74F153137492-001

Capacitors

15)Integrated Circuit, 74F74137436-001c2Capacitor, 47 UF, 25 V, Electrolytic124009-476
15KIntegrated Circuit, 74F04137437-001C3Capacitor, .1 UF, 50 V, Ceramic122002-104
15NIntegrated Circuit, LB137536-001C4Capacitor, 470 UF, 25 V, Electrolytic, 123003-477
15VIntegrated Circuit, 74F74137436-001Radial
csCapacitor, .22 HF, 50 V, Ceramic122017-224
Page 37

Ilustrated Parts Lists Badlands Universal Kit

Badlands Game PCB Assembly , Parts List, Continued

DesignationDescriptionPart No.DesignationDescriptionPart No.
C6-C9Capacitor, .1 uF, 50 V, Ceramic122002-104RI6-R19Resistor, 3.3 K Q, +5%, 1/8 W110027-332
C10-C15Capacitor, 100 pF, 100 V, Ceramic122016-101R22-R25_Resistor, 470 Q, +5%, 1/8 W110027-471
C16-C24_Capacitor, .1 HF, 50 V, Ceramic122002-104R26, R27 Resistor, 24 K Q, +5%, 1/8 W110027-243
C25-C28Capacitor, .001 YF, £10%, 50V122015-102R30Resistor, 100 K Q, +5%, 1/8 W110027-104
29-C32_Capacitor, .01 HF, 50 V, Ceramic:122002-103R31Resistor, 220 Q, +5%, 1/8 W110027-221
C33Capacitor, .1 UF, 50 V, Ceramic122002-104R32-R35_Resistor, 1 K Q, 45%, 1/8 W110027-102
C35Capacitor, 47 UF, 25 V, Electrolytic—124009-476R37-R41Resistor, 10 K Q, +5%, 1/8 W110027-103
C36, C37. Capacitor, .1 UF, 50 V, Ceramic122002-104R42Resistor, 1 K Q, 45%, 1/8 W110027-102
C38Capacitor, 10 UF, 25 V, Electrolytic124009-106R43-R45_Resistor, 10 K Q, +5%, 1/8 W110027-103,
39Capacitor, .001 HF, +10%, 50V122015-102R46-R56Resistor, 1 K Q, +5%, 1/8 W110027-102
C40, C41Capacitor, .1 MF, 50 V, Ceramic122015-104R57Resistor, 470 Q, £5%, 1/8 W110027-471
C42Capacitor, .001 UF, +10%, 50V122015-102R58-R6OResistor, 1 K Q, +5%, 1/8 W110027-102
C43, C44 Capacitor, .1 uF, 50 V, Ceramic122002-104R61Resistor, 5.1 K Q, +5%, 1/8 W110027-512
C45Capacitor, 47 UF, 25 V, Electrolytic — 124009-476R62Resistor, 12 K Q, $5%, 1/8 W110027-123
C46Capacitor, .1 UF, 50 V, Ceramic122002-104R63Resistor, 47 K Q, £5%, 1/8 W110027-473
C47Capacitor, 22 WF, 35 V, Electrolytic124000-226R64Resistor, 12 K Q, £5%, 1/8 W110027-123
C48Capacitor, .1 UF, 50 V, Ceramic122002-104ROSResistor, 1.5 K Q, $5%, 1/8 W110027-152
49Capacitor, 0022 MF, 50 V, Ceramic122015-222R66Resistor, 1 K Q, $5%, 1/8 W110027-102
C50Capacitor, 001 HF, 10%, 50V122015-102R67, ROS Resistor, 18 K Q, +5%, 1/8 W110027-183
51, C52 Capacitor, -1 WF, 50 V, Ceramic122002-104RODResistor, 560 Q, +5%, 1/8 W110027-561
C53Capacitor, .22 HF, 50 V, Ceramic122017-224R70Resistor, 470 Q, +5%, 1/8 W110027-471
C54, C55. Capacitor, .001 LF, +10%, 30V122015-102R71Resistor, 1.5 K Q, +5%, 1/8 W110027-152
C56, C57. Capacitor, .1 YF, 50 V, Ceramic122002-104R72Resistor, 100 Q, +5%, 1/8 W110027-101
58Capacitor, 10 HF, 25 V, Electrolytic—124009-106R74Resistor, 2.4 K Q, +5%, 1/8 W110027-242
C59, C60 Capacitor, 100 pF, 100 V, Ceramic122016-101R75Resistor, 15 Q, 45%, 1/8 W110027-150
€63-C116 Capacitor, .1 LF, 50 V, Ceramic122002-104R77Resistor, 10 Q, +5%, 1/8 W110027-100
DiodesR78Resistor, 1.5 K Q, 45%, 1/8 W110027-152
CRI, CR2 Diode, 1N4001131048-001R81Resistor, 2.4 K Q, +5%, 1/8 W110027-242
CR3Diode, MV5053, Light Emitting131027-002
CR4, CRS. Diode, 1N4001131048-001R82Resistor, 15 Q, +5%, 1/8 W110027-150
CRG, CR7 Diode, MV5053, Light Emitting131027-002R83Resistor, 1.5 K Q, +5%, 1/8 W110027-152
R84Resistor, 10 Q, +5%, 1/8 W110027-100
7Inductor, 100 rae141024-001R85Resistor, 1002, +5%, 1/8 W110027-101
‘TransistorsR86Resistor, 2.4 K Q, 45%, 1/8 W110027-242
Q1-Q3Transistor, 2N5306133033-001R88Resistor, 1.5 K Q, +5%, 1/8 W110027-152
O4Integrated Circuit, TDA2030137301-001R89Resistor, 15 Q, +5%, 1/8 W110027-150
Q5-Q8Transistor, 2N3904133041-001ROLResistor, 10 Q, +5%, 1/8 W110027-100

Resistors

R1Potentiometer, 10 K Q, Vert, with119020-103R92Resistor, 1000, +5%, 1/8 W110027-101
KnobR93-R95__Resistor, 10 K Q, +5%, 1/8 W110027-103
R2Resistor, 100Q, +5%, 1/8 W110027-101R96, ROTResistor, 1002, +5%, 1/8 W110027-101
R3Resistor, 18 K Q, +5%, 1/8 W110027-183ROSResistor, 10 Q, +5%, 1/8 W110027-100
R4,R5Resistor, 1 K Q, 45%, 1/8 W110027-102
R101_Resistor, 1.5 K Q, +5%, 1/8 W110027-152
RGResisior, OQ, $5%, 1/4 W110005-001R102_—Resistor, 3.3 K Q, 45%, 1/8 W110027-332
R7-R9Resistor, 220 Q, +5%, 1/8 W110027-221
R10-R14_Resistor, 1 K Q, +5%, 1/8 W110027-102RNIL-RN3_ Resistor Network, R2R118016-001
RISResistor, 10 Q, +5%, 1/8 W110027-100
Page 38

Badlands Universal Kit Hlustrated Parts Lists

Badlands Game PCB Assembly Parts List, Continued. Designation Description Part No. Designation Description Part No. Miscellaneous Socket, 28 Pin, 600" 179257-028

Switch, Slide, SPDT160040-001Socket, 16 Pin, .300”179259-016
X1Crystal, 14.318144000-004Socket, 24 Pin, .300"179259-024
Connector, 11 Ckt, Header, 100179118-011Socket, 20 Pin, .300”179259-020

Ctr, Key 3

Connector, 2 Ckt, Header, 100 Ctr179048-002Socket, 40 Pin, 600”179257-040

Socket, 64 Pin, .900” 179256-064 Connector, 2 Ckt, Header, .100 Ctr 179048-002

Page 39

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 40

Chapter 5

Schematic Diagrams

About this Chapter...

This chapter contains the sche- Parts Lists.) The Steering PCB,

matics for your Badlands Univer- memory map and the faulty

sal Kit.™ The Badlands Game RAM/ROM tables are also shown.

PCB schematic has six pages and The part numbers for the steering

is shown in ths chapter. (The as- PCB are shown in the steering

sembly drawing and parts list for assembly drawing in Chapter 4.

the game PCB are shown in Chapter 4, Illustrated The Badlands game does not have an audio PCB.

Page 41

Schematic Diagrams

5-2 JAM-88)

ces +4 cer pence : Raa 10K Badlands Universal Kit

ono.

  • * as. Ret R20

1K 1K

seet-23)

7 Ras sret-24) 10K +50. aoe lee wy ‘est eso. GND ono. pay_23 | RETA Ea x a i cates +5v. - cua oop Soin asi oat pase HE vat-ce! i Slot oa[8 JAM-OD, aan f ree pele Saree: aan Stour 035 ca) 10K 5 R19 tates [x2 ae agg}

a? » tf a as]? = 15 aai® & Yr ns FT pO) 16 20 remttoves-t SELFTEST ieoeatl Tap 02 /test aie No. bear oes

Page 42

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 43

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 44

Badlands Universal Kit

26r, Schematic Diagrams

:

7 nN 3lo0 alg—ramois

  • fly ale RaMDsd

Tl? ~ She Blo = a} eawor1 819 ~ ap? RAMOS

Dis ——————— ‘D4 _— 012 O11

a Oa

i — ot

agit 2 ‘

Fesepatfey

yee = psi 4a

Reniele

sae malts oo Stas |,

votive tt |OrasBY
No.Oa18se

O04e fe Bees zi, alito7 ins Hock 2 Yas nai Sas newt cat, She Bs ao5 a@— pa AS Sie OF 213" al2—o9 3 08 ven 7 ROMRE. ze AA Fra 9. ono—2{o s af S$. wr ab ate S08

a 13 7RES. 13 23. pee MOOCLK Ps

ies ie aw /aunres mista soe

7 PUDRESO

Figure 5-1 Badlands Game PCB Assembly Schematic Diagram, Sheet 2 of 6 047194.01 C

5-5

Page 45

Schematic Diagrams Badlands Universal Ki

“ Boa Pon oP /PFBEND FOO

» ReMDIS—3/o Remois—to al q anos 220 4 a jo 3 RanDs— 20 ~ any cna) i

RAMO7—2lo a) Renoe—lo RaMOS—Zo a)

ox 5 pewoe tale Fa hes noi —tlo a i —_—— Rewpo—2l0 ~ 0 a a ay ttt 1, it - Na. a 2N 48 1 4 Aas aus rae Eat) ana ates

HeamangEmigmss
Heterooa2am
Eelam 8tela satin St
a1 pL ssSeoptsyplas
qEAE AECcae ACSaig, Sclaed.
4y.Sina 4SHea tal 38Sina oat
av.Tas oldsTea 0:Ties o3t$3
iv-Sfae oe }43Faz oe aeStee 02} 42
ce|eofce OF

pease let eggeno Te fee /PFALS 7PFALG

  • %

5-6

Page 46

Badlands Universal Kit ‘Schematic Diagrams

+ an aA a a

|if1iy

tS 5

=*4

+H Sy 8

'a3 |
r7A2/y |
:.q

'- +5u-Y}o al a q

————-ox

4u, 2u. ‘4HD2H.-

faistHns |*5V-

rata a ave 2 2

ae)zat)Fal™

Aizey Atzes rtd nace slay sel 8 es

SnelShaABlo a /CRaMAS
a7 o7 3Har o7|30 ~ ale-g43/9 = a2 /cRAMAA
eStine 0640S ale ty0 5 al /CRana3
a5 05|As os|Zo & alsao 8 aie /cranne
Hela beeHes tae ba75.7ERAMPS
tat oHWea oyayyray dsh
20, on]0,00}cus7PF

reget Pe vergete ee

PrALE./PFRLS.mR

; “a tha» of -e-/93 So = of“ yore OS alsa /Prt fo a2 2 7Pro rato “A

Figure 5-1 Badlands Game PCB Assembly Schematic Diagram, Sheet 3 of 6 04719401 C

y Nn

Page 47

Schematic Diagrams

a3 roe 14 7M01-

BEREEGRRE & gy

ROSSA SSBR ES SES Badlands Universal Kit

0817. a

ey

7H0A16

es *e

Z78HDGH—¥ 744024: 72H

woatz. MORALE: BRRBRARVTTE z

ce —Ten a4 7#SYNCDO.

NOT INSTALLED

Page 48

Badlands Universal Kit Schematic Diagrams

toy +5v. oS2 roxan—d are CRAM sae bs Fra 403 screm—e2io § als

nos*d>* Se crememothapsHy
FooLor2D

+ it-~res0 Caan CRAMOE oon wer Ls08 oS,

ssera ta

= syst moa ASME sg —~8 cran—2s—$3,

.ceFoo

8k » 10K onottase GND-

prto—fo ald2a
Hooley4page

ln al

a2Sttitt+fs —sene

To «4 ja 2 al

2g X afteieS.lo N ae—-RED2
aa) GlasA6oS as Reot
33/y~ gfzla ~ aS GREENS
4 OF£.ry3? GREENS

ery | ronemup Jet ef 19K GND- . CREME: al, he aoa :

ar—TrRS 4DAs-AB
AeaHe _aebaa

asa Sy o13—Ha a 1 ace

ae, ~o1o—Ha& 9|

40 26 Dita 9 3 4

/CREaloo

wer? |? /CRAM-

SK 30 a2 GREENS flo a|=—GREENZ To | alk —GREENI ale ase BLUES Halo @ GS acueg ato ~ ole BLUES joa BLED “ae prxcuk ttt]? rate]

/MISC2. a7 AUDFULL: PR +5V- 15\ Lio F74 48 {o § al? —moaiz

du a} moni7

rr +5Vsay Larrea 2 NOT INSTALLED

240 $ a}2—moAi6

:‘BHOGH-}2— monte

T +5u:

Figure 5-1 Badlands Game PCB Assembly Schematic Diagram, Sheet 4 of 6 04719401 C

Page 49

‘Schematic Diagrams ‘Badlands Universal Kit

35 / TROACK

: He 4 R70 0

AGND—&—_———_—_—_-

:

42K

5-10

Page 50

Badlands Universal Kit grams

13 156

sor—Hoapisois—to a —s07
S0e—Hoa —D14Or4—H0al — 06
.sos—foaif —013o13—4ooft $05

soso | afore 1280 | aft S04 S03—Z7jo & ast Orato = ae 803 AM-8

qloape

S00—2]o ~ ali be 08449 ~ oft 500 5 of Atte napa 7eupWR—~— 7ROP- +5V. +5v.

  • tasers 15u 44 74
adio $ gLS_AuoFULL
a} /avorra.3/MAINIRO

Same 6: vi2u R56 c7 tear Lcasicse 44538, . tovesy x J cre

saeelaeaededSnvsos3

sb spp 3 cn. AGNO CRT

302coc36Lease tcstt

“TEST. /MAINIRG- /PUDIROff

aTeapa477250

thea Teerasy Loom Lt

Figure 5-1 Badlands Game PCB Assembly Schematic Diagram, Sheet 5 of 6 047194-01¢

5-11

Page 51

Schematic Diagrams Badlands Universal Kit

aNe oR a BREENStp——Sloe our GREEN3- 303 EENC- 3] RoR GREEN1. 0 GREENO- {00 ik GND- NO rs) z ied u cE} F260 tas

= BLUES- 05, SLUEs—p —4 jos our) erue3— tp —F toa BLUEZ- 4102 gor SN. eign 1K oe.

aq 4d D 6 td reso

INSTALLEO = R73,76,79,80,87, AND 99 = JAMMA LEVELS INSTALLED = 874,75,61,62,86, AND 89 = ATARI LEVELS 2K NOT INSTALLED

RED» avip-1 WE 2 REN AVIO-4 auID-s ed oA 8 avIo-9 SYNC AvIO-20 AvIO-it

/HSYNC

5-12

Page 52

Badlands Universal Kit Schematic Diagrams

+50.

eyo cer Lees Lew Lev

C308 arpa opis Lope Leis Lesse

+ alg

o1P20

Figure 5-1 Badlands Game PCB Assembly Schematic Diagram, Sheet 6 of 6 04719401 C

Page 53

Schematic Diagrams Badlands Universal Kit

J1-2

opt

~ s Ja-t 3 3

~

OAs 4-4

Ws GND _s 44-3

Steering PCB Assembly Schematic Diagram

Faulty RAM Locations

RAM TypeLocationVideo Display

ae Characteristic

CPU/Video22v.Background color‘is'ted

: "and foreground is black.

ColorRAM~~ 8KBlack and yellow are thi

“main colors. »:

Faulty Upper or Lower Main ROM Locations

Error Address * Location on Game PCB

00000 U=20F L=27F 20000 7 UsI7E . L=24F

5-14

Page 54

Badlands Universal Kit

ADDRESS.

000000

008000

010000

C0000

C0000

FD0001,

FEOO01

FE2001,

FEA001

FE6OOL

FEB000

FBA000

FECOOL

FEEOOL

FFCO00

FFEOOO

FPFOOO - FFFIFF

FFFOOO ~ 007FFF

~ OOFFFE

  • O3PFFE

~ FDOFFE

~ PRC3FE

~ EFEEFF

  • PRFFFF Ste

16RW

16KH

9exw

2s6w

28208

1688

4B Schematic Diagrams

BADLANDS MEMORY MAP

ADDRESS BUS DATA BUS

2222 1111 1111 1100 0000 0000 1111 1200 0000 0000

3210 9876 5432 1098 7654 3210R/W5432 1098 7654 3210 FUNCTION
00 OAAA AAA AAAA AAARDDD DODD DODD DDDSHORT ABSOLUTE PROGRAM PROM
BBA AAAA AAAA AAARDDD DDDD DDDD PODSLAPSTIC PROGRAM PROM
O-- -AA AMAA AAAA AAAA AAARDDD DODD DDD DDDDLONG ABSOLUTE PROGRAM PROM
000- — — —wAUDIO RESET
000- — — —RDAUDIO TRANSFER LATCH FULL
000A AAAA AAAA AAAAB/WDDDD DODDARON.
000- — — —WWATCH DOG
oo1- — — —WVIDEO IRQ ACKNOWLEDGE
o10- — — —RDppD DDDSHITCHES

D SELFTEST (ACTIVE 10)

D BLANK

D BUTTON 1 (ACTIVE LO)

D BUTTON 2 (ACTIVE LO)

ppp OPTION SHITCHES (ACTIVE Lo)

1-20 o11- —RDoDD DoDDLETA

00 WHEEL 1

on WHEEL 2

10 PEDAL 1

u PEDAL 2

100- — — —WDD DpDDAUDIO WRITE
qoi- —— —RDDD DDDDUDIO READ
10- — — —WDPLAYFIELD STAMP BANK
nu — — —WEAROM UNLOCK
110- —AA AAAA AAROR/WDODD DDDDCOLORAY

° PLAYFIELD COLORAM

1 MOTION OBJECTS COLORAM

AAA PALETTE

AA AA coLor

°ppp ppRED
°ppGREEN (HSB)
1pppGREEN (LSB)
1D pppoBLUE
1-11 1110 AAAA AAAA AAAR/W_—-DDED DODD DDDD DODDPLAYFIELD PARAMETER RAM

RRRR R ROW ADDRESS

cee cee COLUMN ADDRESS ppp COLOR PALETTE D pDDD DpDD DEDD STAMP NUMBER

=11 1211 0000 AAAA AAO—-«=R/W_—DPDD DDOD DDDD DODDMOTTON OBJECTS PARAMETER RAM

© one sae Mor

ppp pppD DoDD STAMP NUMBER

© Lem 14 vou

pppD DDDD D VERTICAL POSITION

poo VERTICAL SI2z

2 Tee 1 MoH

ppp pppp b HORIZONTAL POSITION

D VIDEO PRIORITY ppp COLOR PALETTE

11 1111 AAAA AAAA AAA——-R/WDODD DDDD DDDD DDDDPROGRAM RAM

Figure 5-2 Steering PCB Assembly Schematic Diagram, Faulty RAM and ROM Tables and Badlands Memory Map 047368-01 A

5-15

Page 55

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 56

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 57

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 58

Left Coins

Right Coins

Continues

Conversions

0 Plyr Minutes

1 Plyr Minutes

2 Plyr Minutes

Sessions

GameTime Number (seconds) of Games

0-59 60-89

90-119

120-149

150-179

180-209

210-229 240-269

270-299 300-329 Badlands Universal Kit

Badlands

Statistics Page

Statistics Screen

Total Games

Error Count

Total Game Time (minutes)

Total Credits

Average Time/Credit

Average Time/Game

Average Games/Session

Histogram Screen

Game Time Number (seconds) of Games

330-359 360-389 390-419

420-449

450-479 _ 480-509

510-539 540-569

570-599 600 & UP

Page 59

AC Alternating current; from zero it rises to a maximum positive level, then passes through zero again to a maximum negative level. ACTIVE STATE The true state of a signal. For example: The active state for is low.

ADDRESS ‘A value that identifies a specific location of data in memory; normally expressed in hexadecimal notation. ANALOG Measurable in an absolute quantity (as opposed.to on or off). Analog devices are volume controls, light dimmers, stereo amplifiers, etc. ANODE The positive (arrow) end of a diode. AMPLIFIER A device used to increase the strength of an applied signal. AMPLITUDE The maximum instantaneous value of a waveform pulse from zero. ASTABLE Having no normal state. An astable device will free-run or oscillate as long as operating voltage is ap-

plied. The oscillation frequency is usually controlled by external circuitry. AUXILIARY COIN SWITCH A momentary-contact pushbutton, switch with a black cap located on the utility panel. The auxiliary coin switch adds credits to the game without activating a coin counter. BEZEL A cut, formed, or machined retention device, such as the conical device used to mount a pushbutton switch to a control panel, or the formed device used to frame the video display screen. BIDIRECTIONAL Able to send or receive data on the same line (e.g., the data bus of a microprocessor). BINARY A number system that expresses all values by using two digits (0 and 1). BIT A binary digit; expressed as 1 or 0. BLANKING Turning off the beam on a cathode-ray tube during retrace. BLOCK DIAGRAM A drawing in which functional circuitry units are represented by blocks. Very useful during initial troubleshooting. BUFFER

  • An isolating circuit designed to eliminate the reaction of a driven circuit on the circuits driving it (e.g., a buffer amplifier).
  • A device used to supply additional drive capability. BUS An electrical path over which information is transferred from any of several sources to any of several destinations.

CAPACITOR A device capable of storing electrical energy. A capacitor blocks the flow of DC current while allowing AC current to pass. CATHODE The negative end of a diode,

CHIP An integrated circuit comprising many circuits on a single wafer slice. CLOCK A repetitive timing signal for synchronizing system functions. COINCIDENCE Occurring at the same time. COIN COUNTER A 6-digit electromechanical device that counts the coins inserted in the coin mechanism(s). COIN MECHANISM A device on the inside of the coin door that inspects the coin to determine if the correct coin has been inserted.

Glossary

COMPLEMENTARY Having opposite states, such as the outputs of a flip-flop. COMPOSITE SYNC Horizontal and vertical synchronization pulses that are bused together into a single signal. This signal provides the timing necessary to keep the display in synchronization with the game circuitry. COMPOSITE VIDEO Complete video signal from the game system to drive the display circuitry, usually comprising H SYNC, V SYNC, and the video.

CREDIT One play for one person based on the game switch settings. CRT Cathode-ray tube. DATA General term for the numbers, letters, and symbols that serve as input for device processing. DARLINGTON A two-transistor amplifier that provides extremely high gain. DC Direct current, meaning current flowing in one direction and of a fixed value.

DEFLECTION YOKE Electromagnetic coils around the neck of a cathode-ray tube. One set of coils deflects the electron beam horizontally and the other set deflects the beam vertically. DIAGNOSTICS A programmed routine for checking circuitry. For example: the self-test is a diagnostic routine. DIODE A semiconductor device that conducts. in only one direction. DISCRETE Non-integrated components, such as resistors, capacitors, and transistors. DMA Direct memory access. DMA is a process of accessing memory that bypasses the microprocessor logic. DMA is normally used for transferring data between the input/output ports and memory.

gl-1

Page 60

DOWN TIME me The period during which a game is malfunctioning or not operating correctly due to machine failure. EAROM Electrically alterable read-only memory (see ROM). The EAROM is a memory that can be changed by the application of high voltage. FLYBACK A step-up transformer used in ‘a display to provide the high voltage. GATE

  • A circuit with one output that responds only when a certain combination of pulses is present at the inputs.
  • A circuit in which one signal switches another signal on and off.
  • To control the passage of a pulse or signal. HARNESS A prefabricated assembly of insulated wires and terminals ready to be attached to a piece of equipment. HEXADECIMAL A number system using the equivalent of the decimal number 16 as a base. The symbols 0-9 and A-F are usually used, IMPLODE ‘To burst inward; the inward collapse of 4 vacuum tube. vo Input/Output. IRQ Interrupt request. IRQ is a control signal to the microprocessor that is generated by external logic. This signal tells the microprocessor that external logic needs attention. Depending on the progfam, the processor may or may not respond, LED The abbreviation for a light-emitting diode. LOCKOUT Com, Directs coins into the coin return box when there is no power to the game.

gl-2 LOGIC STATE The binary (1 or 0) value at the node of a logic element or integrated circuit during a particular time. Also called the logic level. The list below shows the voltage levels corresponding to the logic states (levels) in a TTL system. Logic 0, Low = 0 VDC to +0.8 VDC Grey Area (Tri-State Level) = +0.8 VDC to +2.4 VDC Logic 1, High = +2.4 VDC to +5 VDC MULTIPLEXER A device that takes several low-speed inputs and combines them into one high-speed data stream for simultaneous transmission on a single line. NMI Non-maskable interrupt. NMI is a request for service by the microprocessor from external logic. The microprocessor cannot ignore this interrupt request.

PAGE A subsection of memory. A read-only memory device (see ROM) is broken into discrete blocks of data. These blocks are called pages. Each block has X number of bytes. PCB The abbreviation for a printed-circuit board. PHOTOTRANSISTOR A transistor that is activated by an external light source. POTENTIOMETER

  • A resistor that has a continuously moving contact which is generally mounted on a moving shaft. Used chiefly as a voltage divider. Also called a pot (slang).
  • An instrument for measuring a voltage by balancing it against a known, voltage. RAM Random-access memory. A device for the temporary storage of data. RASTER-SCAN DISPLAY A display system whereby images are displayed by continuously scanning the cathode-ray tube horizontally and vertically with an electron beam. The display system controls the intensity of the electron beam. RETRACE In a raster-scan display, retrace is the time during which the cathode-ray tube electron beam is resetting either from right to left or from bottom to top. RESISTOR A device designed to have a definite amount of resistance. Used in circuits to limit current flow or to provide a voltage drop. ROM Read-only memory. A device for the permanent storage of data. SIGNATURE ANALYSIS A process of isolating digital logic faults at the component level by means of special test equipment called signature analyzers. Basically, signature analyzers (eg., the ATARI® CAT Box) convert lengthy bit streams into four-digit hexadecimal signatures, The signature read by the analyzer at * each circuit node is then compared with the known good signature for that node. This process continues until a fault is located. TROUBLESHOOT The process of locating and repairing a fault. VECTOR A line segment drawn between specific X and Y coordinates on a cathode-ray tube. WATCHDOG A counter circuit designed to protect the microprocessor from self-destruc-

tion if a program malfunction occurs. IF

a malfunction does occur, the counter applies continuous pulses to the reset line of the microprocessor, which causes the microprocessor to keep resetting. X-Y DISPLAY A display system whereby images are displayed with vectors. ZENER DIODE A special diode used as a regulator. Its main characteristic is breaking down at a specified reverse-bias (Zener) voltage.

Page 61

fed ped eM e lel eN eM el ee ped pepe el ed eed elle eel pel fel pel ed pel el elelelel (ca

Warranty

Seller warrants that its printed-circuit boards and parts thereon are free from defects in material and workmanship under normal use and service for a period of ninety (90) days from date of shipment. Seller warrants that its video displays and laser-video disc players (in games supplied with displays and video-disc players) are free from defects in material and workmanship under normal use and service for a period of thirty (30) days from date of shipment. None of the Seller’s other products or parts thereof are warranted. If the products described in this manual fail to conform to this warranty, Seller's sole liability shall be, at its option, to repair, replace, or credit Buyer’s account for such products which are returned to Seller during said warranty period, provided:

  • Seller is promptly notified in writing upon discovery by Buyer that said products are defective;
  • Such products are returned prepaid to Seller’s plant; and
  • Seller's examination of said products discloses to Seller’s satisfaction that such alleged defects existed and were not caused by accident, misuse, neglect, alteration, improper repair, installation, or improper testing. In no event shall Seller be liable for loss of profits, loss of use, incidental or consequential damages.

Except for any express warranty set forth in a written contract between Seller and Buyer which contract supersedes the terms herein, this warranty is expressed in lieu of all other warranties expressed or implied, including the implied warranties of merchantability and fitness for a particular purpose, and of all other obligations or liabilities on the Seller’s part, and it neither assumes nor authorizes any other person to assume for the Seller any other liabilities in connection with the sale of products by Seller.

REE e ere eee eee ere eee el elelelelelel ele

The use of any non-Atari parts may void your warranty, according to the terms of the warranty. The use of any non-Atari parts may also adversely affect the safety of your game and cause injury to you and others. Be very cautious in using non-Atari-supplied components with our games, in order to ensure your safety. Atari distributors are independent, being privately owned and operated. In their judgment they may sell parts or accessories other than Atari parts or accessories. Atari Games Corporation cannot be responsible for the quality, suitability or safety of any non-Atari part or any modification including labor which is performed by such distributor.

Page 62

aly

Hs

he a ATARI GAMES CORPORATION

675 SYCAMORE DRIVE a

P.O. BOX 361110 a

™ MILPITAS, CA 95036