CATHODE RAY TOMES

Battle Arena 2 Toshinden

Battle Arena Toshinden 2 (Europe 951124) (Capcom / Takara, 1995) · Manual · 22 pages · 24 sections · original scan

Page 1

‘TAKARA CO.,LTD, 1995 / ALL RIGHTS RESERVED, PROGRAMMED BY © TAMSOFT 1995 CAPCOM CO.,LTD. 1S AN EXCLUSIVE DISTRIBUTOR

OPERATORS MANUAL

AN WARNING

This game is for use in the United States of America and Canada. Sales, export or operation outside of these countries may be constructed as copyright and trademark infringements and is strictly prohibited. Violators are subject to severe penalties and will be prosecuted to the full extent of the law.

CARCOMY COIN-OP, INC. 3311 N. Kennicott Avenue Arlington Heights, Illinois 60004 Phone: (847) 797-6192 PM00142-KIT Fax: (847) 797-6306 020196

Page 2

@NREON* coin-op, inc. BATTLE ARENA TOSHINDEN 2™

THANK YOU FOR PURCHASING TOSHINDEN 2: BATTLE ARENA™, WE INVITE YOU TO USE THE FOLLOWING MAILING ADDRESS, TELEPHONE OR FAX NUMBER FOR PARTS OR SERVICE INFORMATION CONCERNING THIS GAME:

CAPCOM® COIN-OP, INC. ATTN: FIELD SERVICE - VIDEO PRODUCTS 3311 N. KENNICOTT AVENUE ARLINGTON HEIGHTS, ILLINOIS 60004 PHONE: (847) 797-6192 FAX: (847) 797-6306

THE SERIAL NUMBERS OF YOUR GAME ARE LOCATED ON THE PRINTED CIRCUIT BOARDS AS SHOWN BELOW. PLEASE HAVE THESE SERIAL NUMBERS AVAILABLE WHEN CONTACTING US FOR SERVICE INFORMATION.

PLEASE RECORD THE PC BOARD SERIAL NUMBERS HERE:

  • LOWER PC BOARD - SOLDER SIDE: AAMA SERIAL NUMBER:
  • LOWER PC BOARD - COMPONENT SIDE: CAPCOM SERIAL NUMBER.

[Proprietary and confidential information, not to be disclased or copied without the express permission of CAPCOM® COIN-OP, INC.

Page 3

CAPCOM? co-op, inc. BATTLE ARENA TOSHINDEN 2™

TABLE OF CONTENTS

Warranty Information

Kit Inspection

Kit Installation Preparation Installation Marquee Control Panel Components Cabinet Decals System Wiring Control Panel Test/Volume Bracket Speakers Q-Sound Modification. PC Boards

Game Adjustments Volume Control Stereo / Monaural Test Menu Accessing the Menu How to Select an Item Closing the Menu Menu Item Descriptions Configuration Menu System Configuration Game Configuration

Reference Information JAMMA Connections Auxiliary Cable Connections

Template : Control Panel Drill Hole(s)

Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC.

Page 4

GAPEOLL com-op, inc. BATTLE ARENA TOSHINDEN 2™

LIMITED PRODUCT WARRANTY (APPLIES TO DOMESTIC SALES ONLY)

CAPCOM® COIN-OP, INC. (Seller), warrants only to the initial purchaser of its products, that the items listed below are free from defects in material and workmanship under normal use and service for the warranty periods specified:

A. Printed Circuit Boards: One (1) Year B. Electronic and Mechanical Components: (90) days

No other part of Seller's products are warranted.

Warranty periods are effective from the initial date of shipment from seller to its authorized distributors.

Seller's sole liability shall be, at its option, to repair or replace products which are returned to Seller during the warranty periods specified, provided:

A. Seller is notified promptly upon discovery by buyer that stated products are defective;

B. Such products are properly packaged and then returned, prepaid to Seller's designated plant.

This warranty does not apply to any parts damaged during shipment or handling, or due to improper installation or usage, or alteration. In no event shall Seller be liable for any anticipated profits, loss of profits, loss of use, incidental or consequential damages or any other losses incurred by the customer in connection with the purchase of a CAPCOM® COIN-OP, INC. product.

WARRANTY DISCLAIMER

EXCEPT AS SPECIFICALLY PROVIDED IN A WRITTEN CONTRACT BETWEEN SELLER AND PURCHASER, THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

IMPORTANT NOTICE

THIS SHIPMENT HAS BEEN CAREFULLY INSPECTED AND PROPERLY PACKAGED BEFORE LEAVING THE FACTORY. WE CANNOT ASSUME RESPONSIBILITY FOR BREAKAGE THAT MAY OCCUR DURING TRANSPORTATION OF THE GAME. IF THIS GAME IS DAMAGED UPON RECEIPT FROM THE CARRIER, IMMEDIATELY NOTIFY THE CARRIER AND FILE A DAMAGE REPORT.

ii Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC.

Page 5

CAR COMYY COIN-OP, INC.

Check that all of the following parts have been shipped with your kit. If any parts are missing, contact your distributor immediately.

DESCRIPTION QTY KIT INSPECTION

PSX System PC Boards A-0022200 13-0154 $C00104-05 Standoff w/Screw, PCB Mounting BATTLE ARENA TOSHINDEN 2™

Screw, Wood GE1200 Monitor Card AW00192 06-0074 AW00193 Marquee Overlay, Control Panel Decal, Joystick & Button Switches AW00147 Decal, Cabinet Side AW00196-01 AW00196-02 PM00142-KIT 03-0104 Decal - Top, Instruction Decal - Bottom , Instruction Manual, Operators Harness, Stereo Speaker 03-0052 GE2030 Cable, Auxiliary Joystick Switch, 1-Player Start Button (White) Switch, 2-Player Start Button (White) Switch, Button (Red) Switch, Button (Blue) Switch, Button (Green) 03-0050

Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OF, ING, Bracket, Volume/Test

Page 6

CAPE con-op, Inc. BATTLE ARENA TOSHINDEN 2™

CAUTION |

Please read the following instructions to keep the PC boards in good condition:

Do not drop or bump the boards.

Do not spill any liquids on the boards.

DISASSEMBLING THE BOARDS OR REMOVING STICKERS MAY CAUSE THE TERMINATION OF YOUR REPAIR WARRANTY

YOUR REPAIR WARRANTY.

Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC.

Page 7

® (CAPCOM) COIN-OP, INC.

KIT INSTALLATION

AN WARNING:

MAKE SURE ELECTRICAL POWER TO THE GAME IS OFF BEFORE STARTING THE KIT INSTALLATION.

PREPARATION

  • Disconnect and remove the old printed circuit board(s) or cartridges from the cabinet.
  • Remove or open the control panel, and disconnect and remove the buttons and joystick(s) from the control panel.
  • Remove any covering from the control panel overlay, and then remove the control panel overlay.
  • Place the Drill Hole template over the control panel to determine where any new holes should go. Center punch any needed new holes on the control panel.
  • Cut out the new holes using a 1-3/16" hole saw.
  • If there is an additional control panel *cover (such as plastic or lexan) that will be utilized, cut any additional holes using the same template. *Cover is not included in the kit.
  • Plug up unused holes with a wood dowel (1- 1/8" diameter) and sand any rough edges.

INSTALLATION

Marquee Installation

  • Remove the marquee glass, marquee overlay, and the cabinet graphics.
  • Install the new marquee and replace the *glass. *Glass is not included in this kit.

Control Panel Overlay Installation (See Figure 1)

  • The control panel overlay in the kit is oversized to accommodate most control panel sizes. Center BATTLE ARENA TOSHINDEN 2™

the overlay on the control panel, leaving some excess material at the edges.

  • Remove the protective backing from the overlay and press it down on the control panel, keeping it properly aligned. Press it down firmly, smooth out any bubbles, and press it over the edges.
  • Trim any excess from the overlay. Place the drill hole template on top of the overlay, aligning it with the joystick holes. Pierce through the overlay at each control panel hole. Then, cut away overlay material covering the joystick and button holes. Remove the template and clean off the overlay.
  • Peel off the backings of the 6-button and joystick decals, align over the control panel holes, and press in place on the overlay (refer to the drill hole template for proper placement). Using a knife, trim material from the center hole of the joystick decal.
  • Install the control panel *cover (if required).

Figure 1 Overlay Installation

Reassembly of Components

  • Install all buttons and retaining rings on the control panel as shown in Figure 2. Install two RED buttons to the immediate right of each joystick, install two GREEN buttons to the right of the red ones, and install two BLUE buttons to the right of the green ones. Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC.
Page 8

ICARCOMY COIN-OP, INC.

Control Panel Red Green Blue Red Green Blue Tuy s COPE

Red Green Blue Red Green Blue

Buttons: ey) i ie <)

SS OQ) in SS = Retaining —_& Fi Rings Switches weg E

FIGURE 2 Control Panel Buttons and Switches

  • Notice that there are two white buttons. (See Figure 3.) The WHITE buttons are START buttons. Install the PLAYER ONE button on the top lefthand side of the control panel, and the PLAYER TWO button on the top right-side of the control panel.

1 Player

FIGURE 3 Start Buttons

  • Install the switches on the buttons as shown in Figure 2. Orient the switches so that when a button is pressed, the red contact on the switch is depressed.
  • Install the joysticks on the control panel as shown in Figure 4. BATTLE ARENA TOSHINDEN 2™

FIGURE 4 Joystick Installation

CABINET DECAL INSTALLATION

  • Remove monitor glass and install monitor card.
  • Peel-off the backing to the instruction decals and place on both the top and bottom of the monitor card. (See Figure 5). Also, apply the cabinet decals to both sides of the cabinet.

MONITOR CARD

INSTRUCTION DECAL -

INSTRUCTION DECAL - BOTTOM

FIGURE 5 Cabinet Decal Installation

4 Propritary and confidential information, not be dlaclosed or copied without the express permission of CAPCOM® COIN-OF, INC.

Page 9

ICAP COMY Reed BATTLE ARENA TOSHINDEN 2™

SYSTEM WIRING To PC Board Connector CONTROL PANEL WIRING CN2

NOTE: All switch wires used in this game must be wired to the normally-open connection on the switches. Each switch requires a ground wire on the common connector and the appropriate control or switch wire on the normally-open connector of the switch. To

21. Reconnect the existing JAMMA connectors to ean a

the control panel according to the chart in Figure 5. Switches

  • Connect the Player 1 and the Player 2 ESCAPE vacaso va Remo and KICK buttons to the auxiliary cable harness connectors as shown in Figure 6. Make the ane FIGURE 6 connections according to the chart in Figure 7. Auxiliary Cable Harness

JAMMA CONNECTS

CONNECTOR REF.*WIRE COLORTOCOMPONEN’
WHITE/BLACK.PLAYER 1JOYSTICK
WHITE/BROWN,PLAYER |JOYSTICK
WHITE/REDPLAYER |JOYSTICK
WHITE/ORANGE,PLAYER |JOYSTICK,
WHITE/YELLOW,PLAYER 1ESCAPE BUTTON.
WHITE/GREEN.PLAYER 1‘WEAPON BUTTON,
WHITE/BLUE,PLAYER |WEAPON BUTTON
‘VIOLET/BLACKPLAYER 2JOYSTICK,
‘VIOLET/BROWN.PLAYER 2JOYSTICK
VIOLET/REDPLAYER 2JOYSTICK,
VIOLET/ORANGE,PLAYER 2JOYSTICK
‘VIOLET/YELLOW.PLAYER 2.ESCAPE BUTTON.
VIOLET/GREENPLAYER 2,WEAPON BUTTON,
VIOLET/BLUEPLAYER 2WEAPON BUTTON,

Figure 6: JAMMA Wiring Connections

  • Wire Color Note: — Wire colors shown are according to the AAMA -AMOA Standard for wire color assignments; your harness may contain different colors than shown above.

AUXILIARY CABLE CONNECTS

CONNECTOR REF.WIRE COLORTOCOMPONENT.FUNCTION

PLAYER 1 ESCAPE & KICK BUTTONS PLAYER | ESCAPE BUTTON PLAYER 1 KICK BUTTON. PLAYER | KICK BUTTON

PLAYER 2 ESCAPE & KICK BUTTONS ‘COMMON

PLAYER 2ESCAPE BUTTON‘OUT
PLAYER 2,KICK BUTTON.LIGHT.
PURPLE/YELLOW.PLAYER 2,KICK BUTTON.—tHEAVY,

GRAY/YELLOW NO CONNECTION PINK/YELLOW NO CONNECTION BLACK/WHITE NO CONNECTION.

Figure 7: Auxiliary Cable Wiring Connections Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC.

Page 10

® ICAIRCOM| COIN-OP, INC.

TEST/VOLUME BRACKET WIRING

  • An optional Test/Volume bracket (see Figure 8) is included in this kit. Your cabinet may already contain this bracket. If you decide to install the bracket, it should be mounted inside the coin door and on top of the cash box for easy access.
NOTE: Only the Test switch is used for this game; the Volume Up/Down switches are disabled. Volume adjustments must be made through the volume control knob located on the PC board.

‘v300500 Figure 8: Test Bracket

Wiring of the Test Bracket requires connections to the main JAMMA harness as shown in Figure 9:

SWITCH CONNECTS

FUNCTION TO

VOLUME-UP NO

CONNECTION NO CONNECTION NO CONNECTION JAMMA ‘15° JAMMA ‘A’ or ‘B’ or ‘e’ or ‘f or ‘1’ or ‘2’ or ‘27° or ‘28° Figure 9: Test Bracket Wiring Chart LEAD WIRE COLOR

SPEAKER WIRING

28a. If you are converting a cabinet that is not equipped with CAPCOM® Q-SOUND, the leads from the speaker harness (supplied with this kit) must be wired to the cabinet speakers according to the following chart: BATTLE ARENA TOSHINDEN 2™

LEFT (+) LEFT () RIGHT (+) RIGHT (+)

28b. _If you are converting a cabinet that is equipped with CAPCOM® Q-SOUND, you may elect to wire directly to the cabinet speaker terminals, as shown above, or you can obtain the same result by performing the following modification (see Figure 10):

  • Disconnect the speaker harness connector from the Q-SOUND board at location CB8. Please note that the Q-SOUND system will be disabled during this game;

ii) Install a 4-pin, 0.156 inch diameter header connector (not supplied with this kit; purchase locally) onto the speaker harness connector;

iii) Insert each wire lead from the supplied speaker harness to each corresponding pin from a 4-pin, 0.156 inch diameter female connector (not supplied with this kit; purchase locally);

iv) Push the female connector and the header connector pins together.

  • Your cabinet is now equipped to receive stereo sound from the PC board.

TO CABINET SPEAKERS

EXISTING SPEAKER HARNESS

TO GAME

HEADER PC BOARD,

CONNECTOR LOCATION

4-PIN Keay, CN 504 FEMALE CONNECTOR

veesco SUPPLIED SPEAKER HARNESS

Figure 10: Q-SOUND Modification

6 [Froprictany and confidential information pot tobe dsdowed or copied witht the espres prminton of CAPCOM® COINOP ING]

Page 11

CAPO coin-op, Inc. BATTLE ARENA TOSHINDEN 2™

  • Install the four (4) mounting standoffs to the underside of the PC board by securing with the supplied machine screws. Then, fasten the PC board standoffs to the control panel shelf with wood screws, as shown in Figure 11.

MACHINE SCREW ce SCREW get 4)

Figure 11: PC Board Mounting

PC BOARD WIRING CONNECTIONS AND ADJUSTMENTS

  • Connect the JAMMA harness connector to the edge connector located on the bottom PC board (see Figure 12).

ne JAN WARNING

Improper installation of the JAMMA harness connector to the PC board connector will cause damage to the PC board.

  • Attach the auxiliary cable connector to the top PC board at location CN2 (see Figure 12).
  • Attach the speaker harness connector to the PC board at location CN504 (see Figure 12).
  • Check that the mode switch, on the lower PC board, is set to “STEREO” (see Figure 12).
  • Check that all 4 positions of the DIP switch are set to OFF (see Figure 12).
  • Power-up the game and adjust the speaker volume by turning the Volume Control knob clockwise. to increase volume, or counterclockwise to decrease volume (see Figure 12).
  • .Set all operator adjustable options by pressing the TEST switch. Follow the instructions under the TEST MENU section of this manual.

Figure 12: PC Board Wiring Connections & Adjustments

[Proprietary and confidential information, not to be disclosed or without the express permission of CAPCOM® COIN.O1

Page 12

CAPCOM con-op, inc. BATTLE ARENA TOSHINDEN 2™

NOTES

8 Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC.

Page 13

GAP@OHI° coin-op, Inc. BATTLE ARENA TOSHINDEN 2™

TEST MENU

The test menu allows you to test various functions of the game and configure settings used in the game. These items include input devices such as joysticks, buttons and coin mechs, output devices such as monitor, speakers and meters. Through the Test Menu you can also access the Configuration Menu, where you can change the settings of the game.

  • ACCESSING THE TEST MENU

+ Fora CAPCOM® cabinet or a converted cabinet with a test switch: Make sure the game is on. Open the coin door, find the location of the test switch, and press “Test”. The screen shown below will appear on the monitor:

TEST MENU

INPUT

OUTPUT

SOUND & VOICE

COLOR

DOT CROSS HATCH

GAME DATA

CONFIGURATION

  • MEMORY CHECK
  • EXIT

SELECT = 1P UP or DOWN START =1P SHOT1

  • HOW TO SELECT AN ITEM

+ Use the PLAYER I JOYSTICK to move the arrow in front of the desired item and press the PLAYER I ESCAPE IN button.

  • To return to the test menu, push the PLAYER I START and PLAYER 2 START buttons simultaneously. ¢ The test menu will always appear on the screen:
  • After you exit the “7. CONFIGURATION MENU” and
  • After the memory is tested from the menu, “8. MEMORY CHECK”.
  • CLOSING THE TEST MENU

To close the Test Menu, highlight “9. EXIT” and push the PLAYER I ESCAPE IN button.

Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM@ COIN-OP, nc] 9

Page 14

ICAIRCOMY COIN-OP, INC. BATTLE ARENA TOSHINDEN 2™

  • TEST MENU ITEM DESCRIPTIONS

[INPUT Used to test all the input switches, such as joysticks and buttons. The “0” changes to a “1” as the button is pushed or joystick is moved. Check connections and switches in case the “0” doesn’t change to a “1” when depressed or moved.

OUTPUT Used to test the coin meter and the coin lock.

SOUND & VOICE Select a code of SOUND or VOICE with the PLAYER I JOYSTICK. Push the PLAYER | ESCAPE IN button to hear the sound of the selected code.

COLOR Shows color bars of red, green, blue, and white. Adjust RGB and brightness to obtain the optimum color balance and solid black background.

DOT CROSS Used to test the screen size, focus and distortion. HATCH GAME DATA Coin meter and playtime information will be displayed.

CONFIGURATION

MEMORY CHECK Used to change the game play settings. Refer to the CONFIGURATION MENU section.

Used to test memory. “OK” appears when each block of memory passes test, “NG” appears in case of malfunction. If “NG” appears, repeat the memory test and wait for the “OK” message. Contact your distributor if “NG” still appears.

EXIT Select this item and push the PLAYER I ESCAPE IN button to return to game play mode.

10 Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN.OP, INC.

Page 15

CAPCOM coin-op, INC. BATTLE ARENA TOSHINDEN 2™

CONFIGURATION MENU

The Configuration Menu is used to change various game settings such as level difficulty, credits, sound configuration, etc. These settings are stored in memory on the PCB rather than DIP switches.

The Configuration Menu is divided into 2 sections. In the SYSTEM section, you can change credits, sound, and coin door configurations. In the GAME section, you can change the play difficulty level and duration of the game.

  • ACCESSING THE CONFIGURATION MENU

¢ From the TEST MENU, move the arrow to “7. CONFIGURATION” and push the PLAYER I ESCAPE IN button. The screen below will be displayed. A description of each option is explained in the table below.

  • CONFIGURATION MENU

> 1. SYSTEM

  • GAME
  • DEFAULT
  • SAVE & EXIT

SELECT 1P UP OR DOWN START 1P START & SHOT1

SYSTEM | Select this item to change settings for credits, monitor flip, sound and coin door configurations. GAME _| Select this item to change difficulty level, damage level, time count speed, maximum number of rounds and event type. DEFAULT | Use this item to restore configuration settings to the original factory values. Press the PLAYER I START and PLAYER | ESCAPE IN buttons at the same time to select this option. SAVE & Use this to save new configuration settings and exit to the Test Menu. The message EXIT “SAVING NEW CONFIGURATION IN EEPROM” will appear while the new settings are being saved. DO NOT tum power off to the game until “SAVING” is complete and the Test Menu reappears.

[Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COI

Page 16

CAP@OMcom-op, nc. BATTLE ARENA TOSHINDEN 2™

SYSTEM CONFIGURATION

CHANGING THE SYSTEM CONFIGURATION SETTINGS

Move the PLAYER | JOYSTICK up or down to highlight the desired option. Once the option is highlighted, move the PLAYER I JOYSTICK left or right or press the PLAYER | ESCAPE IN button to select.

7-1. SYSTEM CONFIGURATION

. COIN MODE 2 COINS 1COIN CONTINUE

. CHUTE TYPE 2 CHUTES SINGLE

. CONTINUE ON

|. DEMO SOUND ON

  • SOUND MODE MONAURAL
  • EXIT

SELECT OPTION P UP OR DOWN MODIFY SETTING P LEFT OR RIGHT = 1P SHOT1 OR SHOT2

SYSTEM CONFIGURATION ITEM DESCRIPTIONS

  • COIN MODE SELECT THE CHARGE PER PLAY.
  • CHUTE TYPE SELECT THE NUMBER OF PLAYER(S) AND COIN CHUTES. 1 CHUTE SINGLE: WITH THIS SETTING, EITHER PLAYER CAN START THE GAME. 2 CHUTES SINGLE: TWO PLAYERS USE ONE COIN CHUTE AND PLAY AT THE SAME TIME. THE PLAYER WHOSE COIN WAS PUT IN FIRST STARTS THE GAME. 2 CHUTES MULTI: TWO PLAYERS USE TWO COIN CHUTES AND PLAY SEPARATELY. THE GAME STARTS FROM THE SAME SIDE AS THE COIN CHUTE WAS USED.
  • CONTINUE USED TO SET THE CONTINUOUS PLAY.
  • DEMO SOUND TURNS ATTRACT SOUNDS ON OR OFF.
  • SOUND MODE SELECT STEREO OR MONAURAL FOR USE WITH YOUR CABINET.
NOTE: STEREO SHOULD ONLY BE SELECTED WHEN THE CABINET SPEAKERS HAVE BEEN CONNECTED TO THE GAME PC BOARD AT LOCATION CNS504. Q-SOUND IS NOT AVAILABLE FOR USE WITH THIS GAME. TO SAVE THE SETTINGS AND RETURN TO THE CONFIGURATION MENU, HIGHLIGHT THIS ITEM AND PUSH THE PLAYER | START BUTTON.

SYSTEM CONFIGURATION OPTION SETTINGS

1COIN1 COIN1 COIN1 COIN1 COIN
1 CREDIT2 CREDITS3. CREDITS4 CREDITSSCREDITS
1 COINT COIN1 COIN1 COIN2 COINS:
6 CREDITS7 CREDITS8. CREDITS9 CREDITS1 CREDIT
3. COINS‘4 COINS,‘5 COINS‘6 COINS.7 COINS:
1 CREDITCREDIT,1 CREDITCREDIT1 CREDIT
‘8 COINS‘9 COINS2 COINS STARTFREE PLAY

1 CREDIT 1 CREDIT 1 COIN CONTINUE

  • CHUTE TYPE, 1 CHUTE SINGLE 2 CHUTES SINGLE
  • CONTINUE ‘ON OFF ‘4 DEMO SOUND. ‘ON OFF
  • SOUND MODE STEREO MONAURAL

NOTE: FACTORY SETTING

Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC.

Page 17

@APCOLI coin-op, Inc. BATTLE ARENA TOSHINDEN 2™

GAME CONFIGURATION

CHANGING THE GAME CONFIGURATION SETTINGS

Move the PLAYER J JOYSTICK up or down to highlight the desired option. Once the option is highlighted, move the PLAYER | JOYSTICK left or right or press the PLAYER 1 ESCAPE IN button to select.

7-2, GAME CONFIGURATION

>1. DIFFICULTY EL.

. DAMAGE LEVEL

. TIME COUNT

. MAX ROUND 3 ROUNDS

. EXIT

SELECT OPTION 1P UP OR DOWN MODIFY SETTINGS P LEFT OR RIGHT = 1P SHOT1 OR SHOT2

GAME CONFIGURATION ITEM DESCRIPTIONS

  • DIFFICULTY SETS THE DIFFICULTY LEVEL.
  • DAMAGE LEVEL SETS THE OFFENSIVE POWER LEVEL
  • TIMERCOUNT. SETS THE SPEED OF THE COUNTDOWN FROM THE TIMER DISPLAY. 4, MAX ROUND SETS THE NUMBER OF ROUNDS PER MATCH: 1 ROUND: WINNER OF A SINGLE ROUND WINS; 3 ROUNDS: WINNER OF 2 OUT OF 3 ROUNDS WINS; S ROUNDS: WINNER OF 3 OUT OF 5 ROUNDS WINS. RETURN TO THE CONFIGURATION MENU.

GAME CONFIGURATION OPTIONS

  • DIFFICULTY
  • DAMAGE LEVEL Low
  • TIME COUNT

‘4. MAX ROUND

NOTE: FACTORY SETTING

Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC.

Page 18

CAPCOL* coin-op, inc. BATTLE ARENA TOSHINDEN 2™

JAMMA Connections

GND GND +5 VDC

N.C. +12 VDC KEY A B i D Ei E H N.C. +12 VDC KEY N/C COIN COUNTER 1 COIN LOCK 2 COIN LOCK 1 *SPEAKER (-) Nc. VIDEO GREEN VIDEO SYNC SERVICE (FREE CREDIT) NIC

2 PLAYER - START

2PLAYER - DOWN 2PLAYER - LEFT 2 PLAYER - RIGHT 2 PLAYER - ESCAPE IN 2 PLAYER - LIGHT WEAPON 2PLAYER - HEAVY PUNCH NIC NIC GND *SPEAKER (+) N.C. VIDEO RED

VIDEO GROUND

1 PLAYER - COIN 1 PLAYER - START 1 PLAYER - UP. 1 PLAYER - DOWN 1 PLAYER - LEFT 1 PLAYER - RIGHT 1 PLAYER - ESCAPE IN 1 PLAYER - LIGHT WEAPON 1 PLAYER - HEAVY PUNCH

NIC NIC NIC NIC PURPLE/YELLOW_| PLAYER 2 HEAVY KICK NIC NIC PINK PLAYER 1 HEAVY KICK RED PLAYER 1 LIGHT KICK BLUE PLAYER | ESCAPE OUT GRAY/YELLOW PLAYER 2 ESCAPE OUT PINK/YELLOW PLAYER 2 LIGHT KICK NIC NIC GRAY/YELLOW. NIC BLACK/WHITE NIC

BLACK PLAYER 2 COMMON

NIC NIC PINK/YELLOW NIC PLAYER 1 COMMON BLACK

14 Proprietary and confidential information, not to be disclosed or copied without the express per ‘of CAPCOM® COIN:

Page 19

1-3/16" DRILL FOR PLAYER HOLE

1-3/4" DRILL FOR JOYSTICK HOLE

1-3/16" DRILL FOR BUTTON HOLES

@ CAPCOM COINP, INC. 3311 NORTH KENNICOTT AVENUE (CAIRCOM | ARLINGTON HEIGHTS, ILLINOIS 60004 PHONE (708) 797-6100, FAX (708) 797-6119 TMLE

"TOSHINDEN 2" DRILL TEMPLATE

‘DATE DRAWN BY: 1-22-96 JA

80200 bs

Page 20

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 21

CAPCOM co-op, inc. BATTLE ARENA TOSHINDEN 2™

REFERENCE INFORMATION

PC BOARD CONNECTIONS AND CONTROLS

Auxiliary Cable SS Connector Test Switch (Not Used)

Knob

Harness Connector Speaker Harness Connector

TYPICAL CONTROL PANEL LAYOUT OF BATTLE ARENA TOSHINDEN 2™

Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC.

Page 22

NOTICE

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense.

WARNING

Federal law provides severe civil and criminal penalties for the unauthorized reproduction, distribution, or exhibition of copyrighted audiovisual works and video games.

The Federal Bureau of Investigation investigates allegations of criminal copyright infringement.

ICARCOMY COIN-OP, INC. 3311 N. Kennicott Avenue Arlington Heights, Illinois 60004 Phone: (847) 797-6192 Fax: (847) 797-6306

Copyright © 1995 CAPCOM ® coin-op, INc., All Rights Reserved