Spectar Technical Manual V1.0
Spectar (revision 3) (Exidy, 1980) · Document · 39 pages · 7 sections · original scan
SPECIAR
TECHNICAL MANUAL —
SPECTAR (TM)
Technical Manual 1.1
- 1988 Exidy, Inc. 398 Java Drive, Sunnyvale, California 94086 Telephone: (488) 734-9419 Toll-free: (898) 533-8482 Telex: 357-499
FOREWARD
This manual is designed for your ease in reading schematics. A description accompanies each schematic on the opposite page. This should help clarify the schematics and aid in your understanding of the technical aspects of SPECTAR.
The following is an outline of the information contained in the schematic descriptions: To find the particular information you are interested in, look up the schematic PAGE number as listed, and opposite the schematic is additional verbal explanation.
PAGE 1: AUDIO BOARD
- Address Decoding (1D)
- Control Data Latch (2C)
- Tone Data Latch (2D)
- Tone Generation Circuit (1A, 1B, 3A, 3B, 3D)
- White Noise Generation (6D)
PAGE 2: AUDIO BOARD
- Shoot sound Generation (5A, 4A)
- Explosion/Crash Sound Generation (Q3
- Summing Amplifier and Integrator (5B)
- Audio Amplifier (6A)
PAGE 1: GAME LOGIC PCB
- Master Oscillator (1D)
- Element (Horizontal) counters (1C, 1E, 2E)
- Line (Vertical) Counters (4F, 5F, 6E)
- Screen RAM Addresses (7D)
- Coin Input Decoding (1H)
- Hardware Generated Line Positioning PROMS (3E, 45)
- Blanking and Video Clocking (5H)
- Black and White Compositie Video Output (1H)
PAGE 2, GAME LOGIC PCB
» Screen Controller PROM (6D) Screen RAM (7B, 8B) Character Image Storage PROM Power and Signal Selection (1B) Character Generator Output Shift Register (12B) UBwWwnNne
PAGE 3, GAME LOGIC PCB Image Storage RAM
- Character Generator Image Storage RAM (13C, 11C, 14C, 12C)
PAGE 4, GAME LOGIC PCB
- The 6582 Microprocessor (2A)
- Power-on Reset circuit (connected to 2A pin 49)
- Processor Workspace RAM (4A, 5A)
- Main Address Decoding (5C, 5D, 5E)
Memory Map
PAGE 5, GAME LOGIC PCB
- Program Memory (6A through 13A)
- PROM Address Selection (4B, 5B)
- Memory Device "Personality" Selection (11B)
PAGE 6, GAME LOGIC PCB
- Moving Object Horizontal Position (13F, 14F, 15F, 16F)
- Moving Object Vertical Position Counters (16E, 12E, 1E, 13E)
- "Write Moving Object" Decoding (6F, 16H, 5E, 3F)
- Color Interface Output (16B)
PAGE 7, GAME LOGIC PCB
- Moving Object Multiplexing (14A, 14E
- Moving Objects Image PROM (11D)
- Moving Object Video Output Shift Registers (12D, 13D, 14D, 15D)
- Moving Objects Shift Register Load Logic (2F, 16H)
- Moving Object Shift Register Control Logic (15H, 14H
- Memory Device Personality Configuration (19D)
PAGE 8, GAME LOGIC PCB
l. Interrupt Status Latch (8E
- Option Switch Port (15A)
- Control Inputs Port (9E)
- Moving Image Latch
- Audio Board Port
- Control Port Latch (9D)
- I/0 Decoding (7E)
PAGE 1, COLOR ADAPTER BOARD
- Character Generator RAM Division (1A, 2A)
- Video Priorization
- Color Multiplexers (5A, 5B, 5C)
- SYNC and VIDEO Polarity (JPR1, JPR2)
- Output Level Adjustments (6C, 7A, 7C)
APPENDIX A: PARTS LIST FOR SPECTAR
SCHEMATICS
1.
3.
4. GAME LOGIC PCB
Master Oscillator (1D) From this oscillator all dynamic operations are derived, such as the processor clock, the main element and line counters, the shift register clocks, as well as all other forms of timing signals.
Element (Horizontal) Counters (1C, 1E, 2E) These components form the final stages of horizontal timing. All operations in this game requiring horizontal positioning or timing have their origin here. Note that, beginning with signal HCLK (from Clock Divide Counter 2D), there are 256 counts prior to setting signal E256 high. When this signal goes high, it indicates that the horizontal blanking period is in progress. At this time the final counter (1E) is preloaded with a higher number than previously loaded. This creates a shorter count the second time around. The shorter count measures the retrace interval. When the retrace count is finished, the counter preloads with a lower number, establishing a longer count sequence again for “real time” sweep of the electron beam across the face of the CRT.
Line (Vertical) Counters (4F, 5F, 6E) These components form the entire vertical timing operation starting with a clock derived from horizontal timing. These counters count 256 times and then preload with a higher number, causing a shorter count the second time. Thisshorter count measures the vertical retrace interval. Note that signal L256, when high, indicates vertical blanking is in progress. After the completion of the vertical retrace count, the counters once again preload with a lower number. This way they count 256 times during the sweep of the electron beam down the face of the CRT, allowing the horizontal timers to sweep one complete horizontal line for each count of the vertical counters. Thus, the electron beam reaches the bottom of the CRT, after completing 256 horizontal line sweeps. It then begins the vertical retrace count, and the whole cycle begins anew with the beam starting again at the top of the CRT.
Screen RAM Addresses (7D) During the time the screen RAM is examined by the logic for output to the monitor screen, addresses must be applied to the screen RAM to count up ata rate corresponding to the image cells conceptually arranged on the screen in a32 x 32 matrix. The counts used here, 4 from the element counters, and 4 from the line counters, fulfill this timing requirement. The least significant element count used (E8) represents an interval exactly eight times that of one element. The least significant line count used represents an interval exactly eight times that of one horizontal line, or eight times a single line count. Dividing a 256 element line by 8 yields 32, and likewise dividing a 256 line vertical sweep by 8 yields 32. Thus the screen RAM address lines (RAMO through RAMS) count ata rate that creates 32 horizontal counts and 32 vertical counts as the electron beam sweeps the face of the CRT. This makes 1024 conceptual “image cells” into which can then be inserted images of 8 elements by 8 lines. For more information concerning these images, refer to the text for page 3 of the Logic Schematics.
. Coin Input Decoding (1H) Some models of SPECTAR contain two separate coin inputs for special coinage applications. NOR gate 1H combines these separate inputs, making signal SCOINT, which sets the interrupt flip-flop (6E on page 8) when either coin input becomes active, thus forcing the microprocessor to jump the interrupt service routine. This interrupt driven operation prevents ever missing a coin when inserted. However, this also means that when a game is first powered up, the coin input must be inactive. If for some reason the coin input switch is enabled at the time of power up, the game does not properly initialize until the switch is disabled.
Hardware Generated Line Positioning Proms (3E, 4E) These PROMs are not used for SPECTAR. Generally their function is to create solid or dotted lines on the screen.
Blanking and Video Clocking (5H) , Flip-flop 5H merely combines blanking and all other video.
Black and White Composite Video Output (1H) This circuit is not used for SPECTAR. If desired, however, these components may be installed to aid troubleshooting, by acting as a “video probe”. ‘
REVISIONS
| Zone | U | DESCRIPTION | DATE | APPROVED |
A $6301 GY HARDWARE GENERATED LINE POSITIONING
| “eos | Proms | COIN INPUT DECODING | pup 2 |
| COInt | rr | ines |
W289 MH b fy
| (i | Led | ax 4 | L308 | _2| eso | |
| KER | SAK | Sod? resver | 432 | wo | : |
o ck
| id Wiheery | 1a8 3) nor | GHDLE | 3H |
£64 Y\IVUSED xD £227,
| WCLK | 6. SPECTAR, | | ev ble | Pi |
| aa | £8 | 4t_1 5) 4597 | voy |
s: -£8_5|
| bi | 53882 $e | was | ESRD. | VIDEO SUMMING |
SCEWID Bak SMOIVDT MORVDT
| ELEMENT CHORi2 ONTAL) COUNTERS | L644 Sax \¢ | ts|? Sig | osLE | BLANKING # VIDEO | |||||||
| sy 5 | "To 4 | na) 748974 Lig | GHSLE | nor ust | SDCBLB | CLOCKING | |||||
| ug 1) GOO | | 1a | ni | lis. SHOE | on | |||||||
| 296 | | se256 | us | lia | 4 | 1 | ia | ere | SPECTAR | scvp | al,” 4 | c |
| ~ | ry | E256 | £128 a Nor | BEQ56 Zz | Es bEBSE | “g74 | |||||
| | I | arn | _£64_4| useD | Scece 4 | |5____éc ang | Plea | ||||||
| qa ly Is |e | £3, | on | VEL | 7 | 2VvL1 | Ssecik We | |||||
| PRE ABD | ia | ——_F | f_-"s— | ||||||||
| f | eye 4-3" git I | |? susie. | £16 | SPECTAR | sync | ls | B | |||||
| WHLsI6) | THR | 13) 74Ls02.) | |||||||||
| re | $60} be"ae | cae | ee 5 | go | Wd eag | al Py) | |||||
| alél | gal, glz__4sywe | 1 | y | |||||||||
| Ik | in @ | Sts26 | \ | ||||||||
| Be id P ya. it | bi | a | Sla56 4 tse | Ys 74) | |||||||
| SCREEN RAM ADDRESSES | SSCL | ee |
——| CD
| £136 | al” "he | RAN | ||
| eH | 4) MHSAM! Lig | RAMZ. | ||
| an | | | 4 | Ma, | |
| Eg | 8 | la | RAM) | NOT USED |
| i | i7PA ~~ ay] | RAMO | BLACK ¢ WHITE | ‘on |
| 15 | le | RAM | COMPOSITE | SPECTAR |
| LINE (VERTICAL) COUNTERS | 13 | pe | VIDEO OUT PUT. | |
| ml | 4 | RANT | 8 |
ig e—Byccey 2 esao_, 'Y SESBD 5 5 Is WE
| cay |e | ep | al* he | Ran. |
7HESI64 musa
| wl, TES | af msa4! Lig | RAS |
> aa A aaa =
| ' 1S ' | lee perl | ie | Ppa |
| sep iT | oS | pda | |
| SCONL 15; | 15 GCOINS | ee g t* | “ey oo |
SCOIN2 13| 74524117 6COINA
| 4H | Ty] Ge | PART OR | NOMENCLATURE | T | ||
| 16 | _¢ | 7] | [ | ARQ] eky | iene No, | On DESCRIPTION | { |
| 28. | 26 | PARTS LIST | ||||
| L____s4 | urz "9 | DIMENSIONS Ant IN INCHES | PECT | (™) |
TOLERANCES. ARE
| Lb | = | i | aed = | - | if | 6502 GAME LOGIC PCB |
MATERIAL SYNC AND VIDEO GENERATION NSH ‘SIRE ] CODE IDENT RO. [DRAWING RO. 77-3374~1) NEXT ASSY | _USE ‘APPLICATION DO_NOT SCALE DRAWING
| 7 | 6 | 5 | ‘ | 4 | 3 |
1.
e GAME LOGIC PCB
Screen Controller PROM (6D) This PROM controls the direction of data flow into and out of the screen RAM and character generator RAM. It prevents timing errors and buss conflicts, assuring that the microprocessor can write to either the screen or character generator RAM, or read back from either.
. Screen RAM (7B, 8B) The screen RAM is comprised of two 1024 x 4 static RAMs, configured to act as a single 1024 x 8 RAM. This creates a screen matrix of 32 horizontal by 32 vertical positions. A single byte code is stored in each of these positions to represent a particular character. During “real time” (the time the CRT is being swept by the electron beam) these character codes address the character generator RAM. Note that the PCB could substitute PROM for character generator RAM, but is not so configured for SPECTAR. These character codes, when used as addresses, are combined with the three least significant line counts (L1, L2, L4) to present to the character generator output shift register all the necessary data to form an 8 element wide by 8 line high character on the CRT, located within one of the 1024 positions mentioned immediately above, that is, the 32 horizontal by 32 vertical positions. The screen, then, is a storage place for single byte codes that call up an 8 x 8 character and place it into the corresponding character cell. This character is stored in the character generator RAM, shown on page 3 of the schematic.
Character Image Storage Shown on this page are two PROMs (9C, 10C). They could be used as a permanent set of characters. However, SPECTAR uses RAM instead, to increase the flexibility in character manipulation. This portion of RAM appears on page 3 of the Logic schematics.
. PROM Power and Signal Selection (10B) This Dip Shunt configures the logic for different types of PROM devices. For SPECTAR, however, this Dip Shunt is unnecessary due to the fact that RAM has been used rather than PROM.
Character Generator Output Shift Register (12B) Video from the character generator memory devices (RAM in the case of SPECTAR) is formed by this shift register as a byte of data that displays one |\ine ata time from left to right on the CRT. This ultimately forms an 8 line high by 8 element wide character positioned on the screen according to the time it is presented to the shift register. Output from this shift register is all the images seen on the screen except the player image and the player missile image.
SCREEN CHIP SELECT and Buss DIRECTION DECODING PROM D7 2|a Blip Be 3 \7 igo 4 3 _cssR DS 4 [le
| VSEL 13] 7 CSCI | D4 5 | is | |
| au 12 @ C8062 | i 10 _EC6BD | D3 Cl iszas [4 | |
| VDIAIO u azsi23 5 SESBD | | | Dz 2 13B \3 | |
| RW \o|“Go [4 S5ECGBD | DI | & | rt |
| E DBDIR | So | bo 3 | a |
| Ss 2 swR 3 | SCREEN RAWIS) | SEcGBO 18 oe | i |
| § | TESEO cipie | (Chak, CODE STORAGE), | DBDR |
= ——_\oir v o—=—_ VO7AIO —_r'i
| aa ar | 7 | RAMS IS[oS wo | 18 lia { | VAS. 22! | |||||
| AB 4 | _ | RAM B16 | he . | | ely | VAB 21 peom [12 | yo? \4 | 313 12 SCGVID | ||
| wT @ | . | RAM 7 n | 1B | 14 | 15 7 | VA? i | te | YD@ 12 | es |
| Re BS | RAMG 1 | 1 im | 3] para EZ | J | VAG 2 | is | ft | Vos ut | ||
| aS Mlisza: [3 | 7 | RAMS 2 | | al'St* fz | tI | VAS 3 | 4 woe vo4 0 | |||
| A \ | AM 4 3 | T | |||||||
| 4 is; eB [5 | T . | RAM | 24 | 5 | { | vas 4 | 13, | t vD3 5 | | CHARACTER | |
| AZ 13 | 7 | - RAMZ 4; 7B | 1 & al + VAR 5. | u | L vo2 4 | LSiee | GENERATOR | |||
| Re 7 | 3 | RAM2 5 | 3 | Vaz e| 3¢ 10 | 4 | vor a{| (8 | ||||
| 5esBo | | RAMI G | 7SRLD | ? Tai 7 | 2 | Yoo 2 | MIDEO oor Pur | |||
| zee Ne | caBO | al | = | ||||||
| ESBD 18 | RAMO 7,4 | ECGBD | vao 8 | if | \ | SWIFT REGISTER | |||
| —| | — | st | |||||||
| aiied | cssr 8 |-— | cscGi_ 18, | ssr_o [5 | 57 | ||||||
| =———acea | | NBs | 5 |
GSWR IO scB.B | 3 =i
| 4 | 18 | y) fvreat_es USED | eo {t® | ||
| Al 7 fea ey] 3 | Le | \e | [ |_|) jvrreo 20 on | sscuk 7 |" | |
| + | SPECTAR | cK | |||
| a = | = | u | 14 | dvaria a) > : | |
| Ls241 | 9 | iS | u“ | See Faye 3 | Vv |
| \A | eo AD 12 | ¢ | ECGBD | ||
| ESBD ‘3 | 7 | 1B | tT | ||
| 5ESB 1 | 1 | 14 | 1 | 22 | 7 |
| ° | @ | rf? | r | 2 | le |
‘a +
| 3] og | ac 2@fa IT 18 t | 7] PROM [5 | |||
| 4] 3 | ag 4 | 10 | 2 | 14 | |
| = | ae G | \4 | + | 5 | =] |
| z | aq 8 | i | + | a | m |
| 5 | AG 17; Lse4! | 3 | - | |||
| cf | L | s | 10 | ||
| cSSR 8B Ao | = ‘Ss ® EA | @ | g | ||
| ————-d¢s | re B | 7 | + | joc |
GSWe 10 =
| ——__aw | Ad n | s | ? | B |
SECGBD 1 | — saa 1 1G cscG2 18
| D7 2] Bia | | | ECOBD S| 05 | qcs |
| de 3 | 7 | L__| | vrp2i_2i| “7 Ose |
| BS 4 | we | vRP20_ 20 _ | |
| a | — | CTA | |
| Da 5 | 1S | Ae fea es | Veer 1g] > PecTAR |
| Da @ |ise4s [14 | al {5 5 | See Page 3 | |
| oc | AO 13 | ¥ | |
| 5 7 | B | seat [ |
7 38 Dt 8 [te
| rr) 2 | Tr | EcGeo 13/4 | CHARACTER IMAGE |
S5ESBO 13 |_— STORAGE _ | ENA peor ie See Page 3 for JOB Alteruate: RAM used
| OM | IE | °. |
1 For PROGRAM ve ret
| —i | , st lover2i | | 1 an veer | |
| PROM | , ys 2° 15 | H | chongeatle gery. |
| Power € SIGNAL | | aewrs° Le | ' | |
| SELECTION | : | 45 \BYRP29 | |
NO SHUNT ; AOS ry
| USED FoR SPECTAR | ! | rae UNArIS |
| 1 ne 98 Fro | | | 6502 GAME LOGIC PCB |
VOTAID 8 S i 1 \BTAB By H
| \ | cy | = |
ere Sree ar oom 2-80 == CO DIP) SHUNT VIDEO RAM RACTER GENERATOR NOT USED FoR SPECTAR AND Sule” EATER 20F8 3374-11
GAME LOGIC PCB
Image Storage RAM
Character Generator Image Storage RAM (13C, 11C, 14C, 12C) These four RAMs, when used in this configuration, act as a 2048 x 8 bit RAM. The images placed on the screen are stored in this RAM by the microprocessor, according to the game program. In this RAM images are established, altered, shifted slightly, and even replaced with a new set, if required by the program. When called by the logic to do so, the RAM presents, to the character generator shift register, a single byte, representing one line of a particular image. Each image is composed of 8 lines of data, each line is one byte-wide. Thus, 256 images of 8 x 8 bits can be stored here simultaneously and “called up” by the screen RAM to be displayed on the CRT in any of the 1024 character cell positions. A single byte code, stored in the screen RAM, calls up a character. The character may change or move by replacing the single byte code in the screen RAM, or by altering the data in the character generator RAM which forms the image.
CHARACTER © GENERATOR IMAGE STORAGE PRAMS
For use with PROGRAM generated chaugeable imagery.
USED on SPECTAR
| VA iS | u vo7 | VA sf vo7 | |
| vas te | 12 VDe | vas | 12 DG |
| var 17] 1024x4 fig vos | va7 | loztx4 | vos |
| VA 1] Ran [4 vo4 | VAG | RAM [ia vba |
vas; 2 VAS
| Vaa B| ena | Vad | 24 |
| VAR, a] isc | a | 14c |
yaa 5 vae VAI e Val VAO 7 vao cscar_ 8 | cscee 10 GSWR___/04
| vas is | u vo3 | u vos |
VAS 16] jorgxg [12 VOR 12 vou
| VAT 7 | 13 vol | ye24eg [BOI |
VAG 1] RAM [a vDO 14 voo VAS z RAM
VAS SB] 214 2u4 VAR a] te vec
Vaz Ss VAI a vao 7 cacay_ 8 Gswr 10 ~~ ___d
6502 GAME LOGIC PCB
IMAGE STORAGE RAM [3 ore
GAME LOGIC PCB
The 6502 Microprocessor (2A) For detailed information concerning this microprocessor, refer to the MOSTEK publication, 6500-10A, MCS Microcomputer Family Hardware Manual. One feature that should be mentioned here, however, is that this microprocessor has “memory-mapped I/O”. This means that all ports interfacing to peripherals of any type must be located within the normal memory map, with no duplication of addresses, since no instructions are specifically oriented toward I/O operations.
Power-on Reset circuit (connected to 2A pin 40) When power is first applied to a game, a particular sequence f events must occur to set up all logic conditions. If this sequence is broken for what ever reason, the microprocessor may become confused, and the game will not start and run. This sequence is accomplished when the reset line to the microprocessor is the last line allowed to reach a “high” logic level. The Power-on reset circuit makes sure this occurs by utilizing the charge time of an RC network as a delay. If any kind of power interruption occurs during normal game play, the power-on reset circuit insures that the microprocessor is reset. This alleviates thoroughly confusing the microprocessor while it also recreates the original power-on sequence.
Processor Workspace RAM (4A, 5A) The RAM, or workspace, consists of the lowest 1024 bytes of memory and can be divided into three separate sections due to distinctly different functions. The lowest 256 bytes (0 to FF Hexadecimal) is reserved for special software register operations, and is called “zero page”. The processor uses this area to store dynamic variables. For details of this type of operation, refer to 6502 technical literature regarding “Zero Page Addressing”. The next higher 256 bytes (100 to 1FF Hex) is reserved for the 6502 stack. The processor stores return addresses in the stack when interrupted or called to execute a subroutine. The game program may also request the processor to store other kinds of information here for later retrieval. The next higher 512 bytes (200 to 3FF Hex) are used as a scratchpad area. Miscellaneous calculations and their results are temporarily stored here.
Main Address Decoding (5C, 5D, 5E) This circuit is the first stage of the address line decoding necessary to organize the memory map; thatis, it places specififunctions or devices within generalized blocks of the memory map, grouped by function. For details on the addressing scheme, see MEMORY MAP, Figure 1.
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
1. GAME LOGIC PCB
Program Memory (6A through 13A) These memory devices are 2716 EPROMS on Spectar. Note that four of the lines to each memory device (PC$0 through PC$7, PAP19, PAP20, PAP21) are programmable through jumper configurations located at 4B and 11B. This allows different memory devices to be used and/or it relocates the program memory within the memory map.
PROM Address Selection (4B, 5B) This is a second stage of address decoding, used to select each individual memory device when addressed. Signal ROMSEL (from page 4 Main Address Decoding) selects the Program Memory devices in general, and jumper 4B, together with decoder5B further defines an address to a particular memory device.
Memory Device ”Personality” Selection (11B) The dip shunt, or jumpers block, alters power and signal configuration to the program memory devices. Note thatthe configuration shown on the schematic requires the use of 2716 EPROMS needing +12v, +5v, and -5v. PLEASE EXERCISE CAUTION regarding any change, in this configuration or replacement of memory devices.
MEMORY MAP Hex Address Function or Device FFF7-FFFF Interrupt and Reset Vectors 5201 Audio Board Tone Data Latch (write) 5200 Audio Board Control Latch (write) 5103 Interrupt Condition Latch (read) 5101 Control Inputs Port (read) 5101 Output Control Latch (write) (Not used in Spectar upright) 5100 Moving Objects Image Latch (write) 5100 Option Dipswitch Port (read) 50CO Moving Object 2 Vertical Position Latch (write) 5080 Moving Object 2 Horizontal Position Latch (write) 5040 Moving Object 1 Vertical Position Latch (write) 5000 Moving Object 1 Horizontal Position Latch (write) 4800-4FFF Character Generator RAM 4000-43FF Screen RAM 0800-3FFF Program PROM 0200-03FF Scratchpad RAM 0100-01FF Stack RAM 0000-00FF Zero Page RAM
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
GAME LOGIC PCB
Moving Object Horizontal Position (13F, 15F, 14F, 16F) Counters 13F and 15F form a 2 byte-wide counter which horizontally positions Moving Object 1 on the screen. These counters are preloaded to a certain value by the microprocessor during Vertical Retrace time. Then, after each occurrence of the Horizontal Sync, they begin to count. The count outputs AND’ed through 15E give rise to signal M1HW, the Horizontal Position Window for Moving Object 1. Counters 14F and 16F are the equivalent circuit for Moving Object 2.
Moving Object Vertical Position Counters (16E, 12E, 1E, 13E) Counters 16E and 12E form a2 byte-wide counter which positions Moving Object 1 vertically on the screen. These counters are preloaded to a certain value by the microprocessor during Vertical Retrace time. Then, after each occurrence of Vertical sync, they begin counting. The four count outputs of the least significant of these two counters (M1L1,M1L2, M1L3, M1L4) are sent to the moving object image PROM to specify which line of the image is presently being displayed. The AND’ed outputs of the second counter give rise to signal M1VW, the Vertical Position Window for Moving Object 1. Counters 11E and 13E are the equivalent circuit for Moving Object 2.
"Write Moving Object” Decoding (6F, 16H, 5E, 3F) Consists of two distinctly different functions. 6F and 16H form the circuit that generates the load pulses for the moving object position counters, while 5E and 3F simply prevent the counters from counting during blanking.
Color Interface Output (16B) This is a 14 pin DIP socket used as the connector interface to the color adapter board. The signals and their functions are: Pin # 1 5SRLOAD = Shift Register Load Pulse (Neg. True) 2 CBLB = Composite Blanking 3 CSYNC = Composite Sync 4 5CVID = Composite Video (Neg. True) 5 SSCLK = Shift Register CLock (Neg. True) 6 HSYNC = Horizontal Syne 7 GND 8 VSYNC. = Vertical Sync 9 5MO2VID —_ = Moving Object 2 Video (Neg. True) 10 5MO1VID = Moving Object 1 Video (Neg. True) 11 VD7A09 = Character Generator Address Line 9 12 SLINES = NOT USED ON SPECTAR 13 VD7A10 = Character Generator Address Line 10 +5V
MOVING HORZ COUNTERS | | MovING OEJECT 2 HORZ, COUNT
De
oS
D3 i
iy
bo
Swe
Pup 3
MHCLK
o7 MOVING OBJECT 4
VERTICAL COUNTERS 1SE MW swmeh
PuP 3
MCL
VERTICAL MOVING OBJECT 2
COUNTERS
Oe
DS
oF
D3
D2.
a
DO
SWMIV
Pur 4 cBLB
WISEL
WEITE
SCBLB
BCLK sal IW
a ist. 0 6 oF 7415134 AT ia], ten swmev
Swen SWMIV z@
o SWMIH A
5E\6 MHCLK 4 iLsog oF
‘wRiTe mMovING OBTECT’ DECODING Near SWM2V
Pur 4
caLB
10. Ls2!
ia ler M2HW
movinig OBJECT 1 =
MoIING OBJECT 2 = PLAYER IMAGE (WUMMEL) MISSILE
_S5RLGAD CBLB 2
SYNC 3
ScviD 4
—SSCLK
HSYNC, /6B
/@ PIN DIP SOCKET COLOR INTERFACE mevw OUTPUT Es
z
v SYNC _e| —smozvip _4] —smoivip _/0
vo7aa? 5 LINES, Le. VD7AIO 13 45 i
6502 GAME LOGIC PCB
=e UA, COLOR INTERFACE OUTPUT AN. MOVING OBJECT POSITION COUNTERS
6OF8 77-3341
i GAME LOGIC PCB
Moving Object Multiplexing (14A, 14E) These two multiplexers pass information to the moving objects image PROM. They contain two codes: one determines which image should appear, and the other specifies which line of that image is to be displayed. The data passed alternates between data for Moving Object 1 (player image) and Moving Object 2 (player missile), depending on the state of element count E32. The upper multiplexer (14A) passes the “which image” code, and the lower multiplexer (14E) passes the “which line of that image” code.
Moving Objects Image PROM (11D) This PROM accepts as data the image and line codes of moving objects 1 and 2 (see “Moving Object Multiplexing” above). It then presents the appropriate data for one line of the image to the output shift registers. The timing of the logic insures that the correct pair of shift registers are loaded with the data, then shifted out at the correct time to become, one line at a time, the 16 lines of video for that character (Moving Object 1 or 2).
Moving Object Video Output Shift Registers (12D, 13D, 14D, 15D) Shift registers 12D and 13D together form a 16 bit shift register whose task is to accept, as data, 16 bits (2 bytes) representing a single line of the image tor Moving Object 1, then shift these 16 parallel bits out serially to become video. This operation is repeated for 16 consecutive lines, resulting in a video image that is 16 bits wide by 16 lines high on the monitor screen. Shift registers 14D and 15D together form this same type of circuit, identical in function, for Moving Object 2.
Moving Objects Shift Register Load Logic (2F, 16H) This circuit sends properly timed load signals to the Moving Object Video Shift Registers. These load signals are needed to load the image data into the shift registers at location 12D or 14D.
Moving Object Shift Register Control Logic (15H, 14H) The input signals to the upper two gates (15H) represent horizontal and vertical position “windows” for the two moving objects (for example, M1HW Moving Object 1 Horizontal Window, M2VW Moving Object 2 Vertical Window). These windows allow the Moving Object shift registers to shift only at the right time. This insures the image is generated at the correct position on the screen. The lower 2 gates of 15H are, in Spectar, used only for later decoding on the color adapter board.
Memory Device Personality Configuration (10D) This is another Dip Shunt which reconfigures the PC board in order to use a PROM (11D) of another type or manufacturer.
oBTECT 2
| MOVING OBJECTS | nesect 4 | | movin |
| MULT PLEXING | Orchuy | | ViIDEN aureiuT |
| ShiFT KEGISTER | | | REGISTER ii |
JUMPER USED ON SPECAR MRI
| mere 13/7815) hie | Vv | 22 | 17 | MVDB | 14. | \ |
| R410 | l 23 | ra | 7 | |||
| me | sg ay | 2708 | Mv 0 | 12) gigi tS MIMD | qa sine ts _M2vio | |
| mere | 7 | UT prom LS | MYO | 1 |
2B ey
| M2Ri 3 1B ir 4 | 2 | \4 | AVDS | 10 | |
| mesial, | 1 | 3 | 1 | MVDS | 5 |
| meat | Ele 4 | mn | MVDS | 4 |
Bey [iS
| MIRE EI | s| HID [io | mvo2 | 3 | ||
| 2 | | | G | a | MV DI | 2 |
1A
| 1aa | ma | seo |
| £3e 1 | 8B] PROG | SSCuK 7 |
LK
| bee | mRel 21 | # | SESR! o a |
| ; | mR20 20 HRLIID-/ | Pure 3 |
meg 1g vari sok MIB 18 Tr “FY si
aoe ee fOD
| mele 13) get Si2 le | | pura \ lo rie! | —J | ||
| maa 1D | 3 | —3°9 Oe ~ |! | ||
| BB sy | @ 15 | ' | ||
| mele | 7 | | | ' | {oO |
28 ay 1 PUPS 3 la MRIS
| matt 3tig iyLS | 1 #e 4 g 13 | 1 | MV DB 14 | MYDS 14 | |
| MILE laa | ‘ —,_ | ' | |||
| laa | H | 5 12 MR2O | | MVDT 12 aes | mv07 12 | 1B |
74L81
| mia, | 1 | te 1 MReY | State | mye ar] tS '66) | |
| mice SI, | ! | 7 10 | ; | ie, | MVDS_10 |
| mui Be | 1 35 a 3 | : | vba 5 | ||
| I4E | We et ae ere ea a __---! | MVD3 4 | |||
| B32 Ney | vy ODIP SHUNT | mvoz2 3 | |||
| 'Sdewa | MYDI 2 | j |
le ENA MEMORY DEVICE
| PERSONALITY | | | 150 |
| SELECTION | zEsRE-olot* | cK |
| wa $i Hi U | Pur 4 3° | ca |
enSigurati howu
| ontiguration show! | ig | cur | |
| 1s for “3 VoeTAGE | usre SST | si | |
| MOVING OBJECTS | ZTOR EPROM | me | : |
| SHIFT REGISTERS | ST | st |
Loab LOGIC
E256 8
| Eoa vel | SELDAI ia | R |
| Eoa | 12|1g20 Yo S_SELAD | LOAD sexe [SESE |
go 0 ja Ele (3) prom [2 _SESRZ
| SEB 3 | Ese | maw \ | ERt 2} | [a sesra |
| — | Ele | mw 2|Lsoo | n| ——" Ja sesra |
men B . 10] ¢33) |S Emvio” Jot G EM2VID
| MIR | 12 | m2vw 12/800 SH | PROG 7 |
y un #
| £32 | 13 | —— | Be |
tsoo sti | [& 6c lo MRI g}isao = , 34 Lise 2 hac _5}tS00 & EMIVID 5
| a | aoe a |is00 o®. | SNOIVDT _ |
MeRIe oo ae 15H
| ___* | Eme2viD 10 | SMO2VOT |
| TMAGE SELECTION LOGIC | | meviDa]isoo b& | NV |
a 15H Which Moving Object?) NOT USED SPECTAR MOVING OSTJECTS SHIFT REGISTERS CONTROL LOGIC 6502 GAME LOGIC PCB
Se
MOVING OBJECT VIDEO GENERATION. 70F8 T-s76-0 ae
GAME LOGIC PCB
Interrupt Status Latch (8E) This latch is set when a coin is dropped or vertical sync occurs. When the latch is set, the CPU is interrupted, that is, signal IRQ goes low. This forces the CPU to jump to the interrupt service routine. The interrupt service routine instructs the CPU to check for a coin input, and then run a debounce routine on the coin bits of ports 9E or 15A, depending on which coin input bit was set at 8E. If the CPU finds no coin input bit set at latch 8E, it will assume the Interrupt condition was caused by vertical sync. This tells the CPU that it should now jump to the routine that services the normal game play, and that the screen can now be updated with new data. The screen can only be updated during the vertical retrace interval.
Option Switch Port (15A) This port provides input from the option dipswitch, at location 16A. Data from the dipswitch is gated onto the data buss and read by the CPU at game start. This allows such options as number of turns, coins per game, additional game versus extra turn, etc.
Control Inputs Port (9E) This port provides input from the controls located on the control panel, such as the joystick, fire button, one player start, andtwo player start. Data from these controls are gated onto the data buss for examination by the CPU during the regular service routine (which is synchronized to the vertical interval).
Moving Image Latch Only the CPU can write to the moving image latch. This latch contains the code that specifies which image or images are presently being displayed by the hardware moving object circuitry.
Audio Board Port This latch is written to only by the CPU and transmits instructions to the audio board when any sounds are enabled, disabled, or the game is initialized. For the functions of these instructions, see the audio board schematic and/or description of operation.
Control Port Latch (9D) This latch, used only in the Spectar cocktail table versions, is written to only by the CPU and keeps track of which player is “up”, in order to select which controls are active, that is, player one or player two.
1/O Decoding (7E) The upper half of this decoder generates the chip selects for those devices written to by the CPU, and the lower half generates the chip selects for those devices which are read by the CPU. See the detailed memory map for more precise information.
| A/D CONVERT: | omen | | ‘ |
| LATCH | surrey, | waving oBTECT |
| A/D CONVERSIO | a a | TATION |
VERSION LATCH
| Not peed on SPECTAR | uze ia[D @lia | nie Te | La" - | ||
| Loa 17[t8374 lie | Elaaszai {7 | 1a|0 lia N2RB | |||
| Laz. ia 1S | ‘Ss s | 12] 68374 | 16 M2R4 | |||
| a | ee | . | 7 | " | 4 1S M2RZ |
on | t
| ts: Bereta [2 | 7 | 3 | ot _ 3) 12 mee | ||
| La 4 | 5 | e | 14 | + | AIRS |
s 1
| it? | 7 | 1 | < | 3 | . | IRA | ||
| ADSEL | [.s00 3 | ue] so [s | | | 2] sa Ne | san | are | ||
| 4 | SEAD | | > | mIRT | |||||
| 13 | 13H | o | oe | | | é | ‘ie | | | | SWMOL |
| 12| E800 Joy | Ss = | | | Slog | |||||
| 10 a | 13H | Li | i |
mzaco 34 a |Ls00 |
| 138 | | | cre | CONTROL INPUT |
| | w4o02 | REGISTER BUFFER | | @
| GEE) | scont 2[A — Y|18 | oe) | |||||
| R19 | R20 | se | * Prown 4 | 748241 Ne | + | 18 ABD? aq | ||
| 10K | 10K | “ | i | + | 3] useas [17 appe | ||
| Cine 4 | aE es | 10 MIADO ma | t Vas . bad | it | 4 | I ABDS = | ||
| cre | 12 |p) | Gre | Fike 8 | ie | T | = | 1s abba CSS |
| us | . | \2H | z | err 7 | meat | oa4 | |
| wor. use | ae esa | a | on 5 | * | * | 6 A803 Gass | |
| SPECTAR | CRB R23 re | | | 7 | = | + | 7 | 13 ABDZ |
| 4454 IK | £26 | Coed. | Za | 2 | | | 8 | (Aor |
| vsync | 3 ie | Gis | ae fg ? | AESE | |||
| ab | + | | 3| isa [ur aevo | |||||
| +5V GBOK eiew | | | aBSEL 18] a5 | us-8 |
sw 4 Lm3400 SRW D R22 ci DR
BIOK _g 3300 o128 S
| ce0 | a] >>> eto | - | D7 |
| Ol | 12H | Ba | |
| wor User | Tt | + | Be |
| on | = | ~ | + |
| SPECTAR | CR4 R25 | D4 | |
| NSYNC IN4#454 1K & | T | REY | |
| ee | pS | r+ |
\ De
| 45V | ceok -—1 | + |
| oy LM3900 | 7 | 21 |
R21
| INTERRUPT DECODING | | , | = | ||||
| T/o DECODING | T__ DECODING JUMPER USED | INTERRUPT CONDITION LATCH | | ||||
| — | FoR SPECTAR | | | | ||||
| TOSEL 13, @F | cate | aa | suze 16/0 @lia | | | wP @]is aos | |
| —— nos | t | LANGUAGE | is374 | * | Ee | |
| write 12 )LS32 | Tyres \. | comt 7 74 lhe | 2 | ie IRI | ||
| Al | Scuillieg | COIN2 Lad ‘iS | —* | |||
| '3\,, Sweee SmolveT 12 | SCOINT. NX | Lie | t4] LS374 [15 W2RIo | |||
| RO 1 TE | VOLV 13 rs | | | ||||
| a” 12 SWMOL St | e | ‘3 | te | |||
| NID | lo | TABLE | 2 | = | z | a4) |
t E
| Tose, 2-2F | uf PREG | SNOIVID 4 | 5 | t | 4 | a | wi=D) |
| a a | BeLK ig | Tse | nat 7| 2 [@ | t | 7 | z | oe) | |
| a | LNGG 8 3 | mt | B| 3D fe | wet) | |||
| +5V Al 3} | le a | " | Qu-z2) | ||||
| |, al | SwePL | 1 | ine | ||||
| L256 1 | sein rs | sv | ;——doe | ||||
| SVGCRY 13 se Vit | —— | R4 |
VCNTC 2 2 ek
| S5COIN2 | 7F | SDye@ | reo | CONTROL PORT |
| “ec | ~ | LATCH |
R308 200
| a | <= _ G3] | a | Sv |
| Al | ° | Sv cw | |
| AUXILIARY COIN | SSSEL G10] a1V _ Gere | a | |
| INPUT. | a arene | TE=7 |
5O Pence ete. =a Se KE 6502 GAME LOGIC PC I/O PORTS sore
AUDIO BOARD
Address Decoding (1D) Uses the audio board select signal ABSEL, the 02 AND’ed write signal WRITE, and Address Line AO to decode the addresses for two input latches. These two latches each receive a byte of data from the CPU instructing the audio board what to do and when.
Control Data Latch (2C) This latch receives a byte of data from the CPU that sets those particular bits directly used as sound enables. Signal TONE is the enable for the programmable tone (or music) generator. Signal CRASH is the enable for the crash or explosion sound. Signal SHOOT is the enable for the player (Wummel) firing saund. SPECTAR does not use signal CPU MUSIC.
Tone Data Latch (2D) This latch receives a byte of data from the CPU that becomes the preload for the most significant counters of the Tone Generation circuit. Varying this preload allows generation of a variety of tones used for music or special effects.
Tone Generation Circuit (1A, 1B, 3A, 3B, 3D) Counters 1A and 1B divide the 02 (phase two) processor clock down from approximately 706 Khz to approximately 34 Khz. This frequency establishes a range of tones accurately generated by merely changing the preload of the two most significant counters in this circuit, 3A and 3B. Flip-flop 3D divides this tone by two again, while transforming a narrow terminal count pulse train into a pulse train having a50% duty cycle. This means it is at a logic high for the same amount of time it is at a logic low, causing a more pleasing sound to the ear. The output of this circuit is then fed to the input of the summing amplifier.
White Noise Generation (6D) Transistor Q4 is the source of this white noise, as its base-emitter junction is broken down by excessive reverse bias. This throws the junction into heavy electron agitation (thermal emission) which activity produces noise across a wide bandwidth. Operational Amplifier 6D is used merely to boost the output amplitude of this noise, and transistor Q5 serves as an output buffer stage to prevent loading of the operational amplifier.
~ q GND +1ZvEc CHI =i2voe“H) ~I2vuc (Lo) = 5 voce THRU +12v0¢ (10) HARNESS SPKR (A) TO +5VDC POWER SUPPLY DOYS URW ~
Sree (6) € SPEAKER
Al AO LoGic PCB INTERCONNECT +5VOC GND +12 voc (Lo) | =5VDC g2 3 POBVESFHAWN-|G
ABD7 PULLUP SOURCES
CONTROL DATA LATCH
TONE, ABDG t V7 Io ABDS —-+
+ CRASH Logic PCB AgD4 i i"
INTERCONNECT ABD3
aa
ABD2Z ABD1 SHOOT. g is
q @
cPU_music WH TE NOISE GENERATION
cPuU music. [Seeseusenala
TONE GENERATION 14,1718,
74LS 161 IB aisle
7ALSIGl VOLUME R23 R46 10K
WHITE NOISE
cae to R49
10K POT
TONE VOLUME wl (SUM 5 input of SUMMING AMP)
a SPECTAR AUDIO PCB SCHEMATIC 77-3376-I1
1. AUDIO BOARD
Shoot Sound Generation (5A, 4A) Both segments of timer 5A are configured to act as free-running multivibrators. The segment on the right receives, as control voltage input, the psuedo-triangle wave created by the charge and discharge of the RC network of the left segment. This creates, in the right segment, a frequency that increases and decreases at the rate of the triangle wave rate. This effectively simulates reverberation. This reverberated tone is then fed to amplitude modulator 4A, whose output amplitude is controlled by the voltage applied to pin 2. Normally (in the quiescent condition) transistor Q1 is ina saturated state, holding 4A pin 2 at a level just under 6 volts. This prevents any audible output from 4A. When signal SHOOT is enabled (set high), transistor Q1 is cut off due to the base being dragged low. This drops the voltage on 4A pin 2 low causing the output amplitude of 4A to increase, creating the player firing sound. Note that both the leading and trailing edge of this amplitude-modulated tone package are made gradual (sloping) due to (for the leading edge) the discharge time of C60, and (for the trailing edge) the discharge time of C14.
Explosion/Crash Sound Generation (Q3) Normally (quiescent condition) transistor Q3 is not base-biased to conduct, therefore the white noise applied to the cathode of CR2 is never passed through the circuit. When signal CRASH is enabled (set high), C35 is allowed to charge through CR1 and R25 toward +12v. As this voltage increases, the base of Q3 receives increasing current and begins to pass the white noise. This circuit is configured to act as an active filter, so the frequencies passed are only those selected for a reasonable crash or explosion sound. The trailing edge of the explosion/crash decays slowly when signal CRASH is disabled (set low) since the discharge path for C35 is through a relatively high resistance (R24). Output of this circuit is also then routed to the input of the summing amp.
Summing Amplifier and Integrator (5B) Two segments of an LM324 operational amplifier are used here. The first is configured as a summing amplifier. It is the common point at which all the various sounds are algebraically added to become one signal. This signal is the composite of all individually developed sounds. This is also the location of the master volume control (R22).
Audio Amplifier (6A) The final audio amplifer is a single IC (6A), configured as a bridge amplifier. The composite audio signal is applied to the input of one of the two internal segments and the output swings in accordance with the input signal. The feedback on this segment is not only fed back to the inverting input of the same segment, but is also applied to the inverting input of the other segment. This creates a condition wherein one segment swings positive, and the other segment simultaneously swings in a negative direction, creating an output twice the voltage of a single segment.
From 20-15 SHOOT SOUND GENERATION
AMPLITUDE CONTROL
+
PACKAGE FORMATION
C60
SHOOT wt ead ay edge”
EXPLOSION /CRASH SOUND GENERATION
CR2
WHITE NOISE IN4454 Ql 2N3904
+12V °
R2E 12k CRI CRASH IN4454 >t RIQ C34 Ri 22K ol to R44 10K WA—— input of @ Por SHOOT SUMMING AMP VOLUME Loci v
INTEGRATOR
SUMMING AWW P od
R21 4.7K
MASTER VOLUME
C3) zizK +! te R44 So inpot of SUMMING AME CEALH VY VOLUME
fren ocsonenon 7 390 JAVAOR SUNNYVALE SPECTAR AUDIO PCB foros se10 SCHEMATIC ~l2v (HI)
Jumpers shown indicate configuration for LM379. pie SHUNT used to alter pinout configuration for use with LM377 or LM378,
- *5V Bypass capacitors (.0lpF cer disc) 2 C1-C4, C6, C8, C23, C24, C25, C27, C80, C33, +12v Bypass capacitors (33 nF tantalum or aluminum electrolytic): C14,C20 All Ic?s with unspecified prefix are 74xx family TTL. All Resistor values are in ohms, Yq watt 5% tolerance , unless otherwise specified. All Capacitor values are in microtorads unless otherwise specified,
COLOR ADAPTER BOARD
Character Generator RAM Division (1A, 2A) The combination of flip-flop 1Aand decoder 2A divides the character generator RAM into 4 equal segments, using the uppermost 2 address lines from that circuit (VD7A09, VD7A10) and the composite video signal (5CV1D). The resulting 4 video lines are then applied to the input of the priority encoder at 2B.
Video Prioritization (2B) All video outputs from the Logic Board are applied to priority encoder 2B. As mentioned in the discussion of “Character Generator RAM Division”, above, the single character generator output has here been separated into 4 different lines, each carrying the video imagery stored in a different quadrant of character generator RAM. These four lines are applied to the priority encoder along with the video output lines from Moving Object 1, Moving Object 2, and signal SLINES, not used for SPECTAR. As shown on the schematic, the input prioritization is from top to bottom. That is, highest priority is assigned to the input shown at the top (5MO1VID) and the lowest to the input at the bottom. The \owest in this case is actually tied low in order to be always active, which creates the background color. The code present on the output of 2B indicates the number of the highest priority video line active at that time. This codeis then applied to the Color Multiplexers to select the appropriate RGB output code for that video imagery.
. Color Multiplexers (5A, 5B, 5C) Each of these multiplexers generates the final video output for a particular base color: red, green, or blue. The priority code from 2B is applied to the multiplexer select lines. This causes all multiplexers to simultaneously output data according to the priority code, and output the data from a particular input pin. The data on each input pin is set up by jumper configuration. Thus, in parallel, 5A, 5B, and SC consider two factors when outputing RED, GREEN and BLUE data: the code of the highest priority video present, and the associated jumper configuration establishing the color of the video.
SYNC and VIDEO Polarity (JPR1, JPR2) Exclusive OR gates 6A and 1C have here been configured to act as “selectable inverters”. Cut the VID jumper (JPR1) and the output video is inverted to become negative true. The same occurs with the SYNC jumper (JPR2). Note that composite sync is available as well as separate Horizontal and Vertical sync outputs. When JPR2 is cut, it inverts all three sync outputs.
Output Level Adjustments (6C, 7A, 7C) The only time these inputs are used is with a monitor requiring unusual input levels. They are not used on SPECTAR.
2_EDB 5 GRUB EmO2VID GRA
| ares | pa FRIAO | eA | BLUA | | | 7 Sus |
| | | 45 | CSYNCA II) 74L$174 lo cynics | |||
| & | HSYNCA 13 | 12_HSYNCB | |||
| ma < Rio | vsyncA 14 | 15 VSYNCB |
GA
| SMOiviD | 86 | RED A | 1 |
74L$139 CUT FoR ——i> 12 oA Lo = TRUE 3
vey be a
| pth | es | a | _HsYMe I | = | #6 ea. RESISTORS _ |
————_ To BE WNSTAWED ned WITH MoniTeR REQUIRING 2.5 Vorr LEVELS
| REDD O | rt~—~™Y | CUT FOR | ~ : |
| LOD IE | 22 ke | reve | ilar |
| keDp 2 | fea | ee |
REDDS REDD4 “kepvs 2]
| REDDE 3 | | 3 | bse | GRN_ovT |
REDD7T 4
| 7 | C | t | REDD | |
rx REDDZ retaz | ¢
| peta | [95 | | | REDDS | |
| eRTAO | If | KeDb4. | 7 | « | BLU out |
REDS REDDG
| Vv | f | REDDT | |
| CANDO _12 | pars | ae | see ne |
GRBDI_13 . CRUD2 14 GRND3_15 GRND4 | GRNDS 2 GRNDE HSYNCB HoOR@ SYNC ID
S5SCLK G2o-@) HEINE —__ VSYNC
@i0-3) SCSYNC To Be msTALED | ONLY WHEN H T20-14 : USED WITH MmolTOR Budo 12 7 $ REQUIRING 2.5 VorT uD
| BiwDI 13 | ‘ | BLUDO | LEVELS. |
| Bud! ue iq is ayn to % BLUDZ 7 Bwd4 1} BLUD3
| L | 2 | | | Buib4 |
GND
| J20-7 | Bude 3) | | | BLU DS |
BLUDG vuuseD = (P2/-F Buds UNUSED — (P21=0 VSYNCB. 9
aay esisrops LG SB=TRG YOO OAC
NOTES! 4, All resichr values shown im ohms
- All capacitor values shown 1 microfarads B. C4-CG (hor SHOWN) are .Oluf cer disc. for BYPASS
foseo ow Treroescnenom —
| Gene Bosad | ee | COLOR ADAPTER PCB | 77-3373-Il |
VIDEO GAME 408-734-9410
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
APPENDIX A
PARTS LIST FOR SPECTAR
Control Panel Assembly
Part Number Description
68-2033-13 75-5177-18 72-3022 38-5076-190 38-5044-18 74-5247 74-6506 71-2391 control panel control panel PSA polycarb silkscreen overlay switch pushbutton with nut and washer control 4-way joysick, long assy. Midway white pushbutton switch assy. carriage bolts 10/24 x 5/8 L black full thread kepnut 10/24 control panel harness
Universal Power Supply Assy
Part Number Description
78-3081 63-4028 or 63-4825 or 63-4935 77-3365-15 71-2389-16 76-1211-10 74-3503
74-5198
74-3502 74-3508 74-4604 61-8072 61-8056 61-8054 88-4992 88-4081 88-4028 88-4098 88-4611 +5VDC Power Supply 6AMP aux. transformer T911
aux. transformer T893
MFG pin 773P9 power supply PCB Assy. power supply harness power supply mounting board screw, #6x1/2 1 phillips pan head selftap screw, #6-32x 3/4 pan hol. phil. machine kepnut 6-32 washer #6 Amer. std plain hex nut 8-32 nylon butt splice, blue plug, 2 pin molex pins, male molex tie wrap, small tie wrap, large wire, 22 ga. buss-uncoated solder SN6@ .®@3 dia. 58 core flex mask and mold seal
American Standard Double Coin Door
Part Number Description
66-4093 66-4097
71-2398 64-2009 88-4002 61-8313 74-3502 Std. double coindoor, Vendall 25 cent Amer. coin acceptor Coin door key (supplied w/ 66-4023) Universal coin door harness coin meter tie wrap, small butt splice red 6-32 kepnut
British/Australian Coin Door
Part Number Description
66-4013-19 Std. British/Aust. dbl. coindoor w/ 16P/50P Coin door key supplied w/ 66-4813-19 71-2417 Aux. coin harness 64-2000 coin meter 61-8313 butt splice red 71-2398 univ. coin door harness 74-3562 6-32 kepnuts
Pushbutton Assy
Part Number Description
72-3061 switch assy. 72-3062 push button 74-6203 pal nut
Spectar Speaker Assy
Reference Part Number Description Location
62-7061 6" x 9" oval speaker
| 61-8856 | conn. 2 pin male molex 93-89-2022 | P4 |
61-8054 pins, male molex 92-99-2118
Monitor Isolation Transformer Assy.
Reference Part Number Description Location
FR 63-4829 Isolation transformer Midwest 773P7
| 61-8858 | Molex connector 93-99-2032 | AC INPUT 22 |
| 61-8054 | male molex pins 62-99-2118 | P22 |
| 61-8857 | molex connector 93-89-1923 | AC to |
Monitor J23
| 61-8055 | female molex pins 92-99-1118 | J23 |
76-1212-598 XFMR mounting board 71-20901-14 xfmr harness 61-8072 butt splice blue 74-6462 washer, #10 plain 74-6506 kepnut 10-24 74-5463-01 screw, 10-24 x 1" ph phil mach 74-5165 fender washer 1/4 ID 1 1/4 OD 88-4062 tie wrap small 61-8313 butt splice red
Audio PCB Assembly
Part Number Description
48-2321 48-2314 48-2071 48-2398
48-2218 48-2342 48-2212 48-2221 48-2211 48-2015 48-2392 47-3005 46-3038
59-5110 59-5189 54-5021 54-5019 59-5070
59-5125
59-5163 59-5625
59-5055 59-5080
59-5146 59-5969 59-5058 59-5128 59-5095 59-5645 59-5040 59-5630 59-5065 23-4030 23-4835
23-4015
21-4020 23-4078 74LS139, IC 74LS374, IC 74LS112, IC 74LS161, IC
72748, IC LM324 NE 556 MC 3340 LM379 (Dual 6W Audio Amp National) 7407 74 LS@4 2N 39064, trans IN 4454, trans
resistor, 2.2K 1/4 w 5% resistor, 3.3K 1/4 w 5% potentiometer, 100K potentiometer, 10K resistor, 22K 1/4w 5%
resistor, 1K 1/4w 5%
resistor 820K 1/4w 5% resistor 1 meg omega 1/4 w 5%
resistor, 47K 1/4 w 5% resistor, 10K 1/4 w 5%
resistor, 109K omega 1/4w 5% resistor, 120K 1/4w 5% resistor, 68K 1/4w 5% resistor, 1.2K 1/4w 5% resistor, 4.7K 1/4w 5% resistor, 190K 1/4w 5% resistor, 156K 1/4w 5% resistor, 560K 1/4w 5% resistor, 33K 1/4w 5% cap, .22 uf ceramic disk cap .1 uf ceramic disk
cap, 6.8 uf 25v dip. tant.
cap, 2.2 uf 15v dip. tant. cap, 22pf. ceramic disk Reference Location
1D 2c,2D 3D 1A,2A,1B,3B, 3A 6D 5B 5A 4A 6A 4c 1¢,3C Q1,03,04,05 CR2, CR3, CR4, CR1 R7 R14 R35 R1,R22,R38 R19,R31,R32, R37 R33,R40,R45, R13 R41 R9,R16,R17, R42, R47 R43 R12,R34 ,R46 R48 R44 R4, R24 R3 R2,R25,R5 R21, R49, R6 R28, R15 R26 R27 R18, R39 c44 c9, C12, C17, C31, C34, C37, C43 c14, C2l, C22, C48, C46, C47 c48, c49 C45
Audio PCB Assembly (continued)
Part Number Description
23-4068 cap, .@@1 uf ceramic disk 23-4056 cap, -91 uf ceramic disk
21-4016 cap, 33 uf 25v dip tant. 22-4825 cap, -47 uf 25v dip. tat.
61-8042 conn., 18 pin female 68-3041 heat sink, thermalloy 6072
22-4032 caps, 10 uf Radial tant or mini electro 25V 74-2586 screw, 4-48 x 1/4" machine 72-3825 dip pkg. shunt 16 pin AMP Part # 435704-8 74-5865 standoff 6-32 x 5/8" nylon or 74-5875 standoff 6-32 x 1/2" nylon 77-3371 Spectar, audio (bare) PCB 74-5182 6-32 x 1/4 machine screw
Universal Power Supply PCB
Part Number Description
77-3365-14 printed circuit board Reference Location
cll Cl, C2, C3, c4, C6, C7, c8, Cl6, c24, C25, C27, C23, C38, C33, C38, C39 C19, C20 cl5, Clo, cee J2, J3 6A (use only w/ LM 379 cl14, c5
6A heatsink 6B
28-4900 4906 uf 58 v axial lead capacitor 21-4819 33 uf 25 v dip tantalum capacitor 21-4915 6.8 uf 35v dip tantalum capacitor 46-3016 60si diode 47-3004 mda 979-1 bridge rectifier 47-3041 "N3055 transistor 47-3011 2N6246 transistor 48-2337 7905T negative 5v LM320T-5 regulator 48-2217 7912T negative 12v LM320T 12 regulator 48-2338 7812T positive 12v LM34@ T-12 regulator 68-3041 thermalloy 6872 heat sink 69-2038 thermalloy 6815 heat sink 61-8618 12 pin male molex 74-2514 4-49 x 3/8 phillips pan head machine screw 74-5216 #4 flat metal washer 74-5191 #4-48 kep nut
6582 Game Logic PCB Assembly
Part Number Description
48-2008 Ic 7409 48-2085 IC 7402 48-2010 Ic 7494
48-2015 IC 7407 48-2828 IC 7408 48-2332 Ic 74LS11 48-2035 IC 7428 48-2316 IC 74LS21 48-2045 Ic 7427 48-2055 Ic 7432 48-2067 Ic 7474 48-2071 IC 74LS112 48-2307 IC 74LS138 48-2321 Ic 74LS139 48-2098 IC 74157 48-2095 Ic 74161 48-2108 Ic 74166
48-2115 Ic 74193
48-2328 Ic, 74LS8241
48-2358 Ic 74LS245
48-2314 IC 74LS374
48-6592 microprocessor 6592 48-2334 2114 (1K x4) RAM
48-9125-81 2708 EPROM (1K 8) HRL 11D-1 x 48-9999-91 6331 PROM (.32 X 8) 48-9899-92 6331 PROM (.32 X 8) 48-9144 6301 PROM (256 X 4) 46-3925 IN4982 diodes 59-5135 res. 470 omega 1/4 w 5% 59-5128 res., 1.2K 1/4w 5% 59-5115 res., 1.8K 1/4w 5% 59-5110 res., 2.2K 1/4w 5% 59-5105 res., 2.7K 1/4W 5% 51-6903 res., 228 omega 1/4w 5% 19 pin sip 51-0082 res., 2.2K 1/4w 5% 18 pin sip 51-9901 res., 4.7K 1/4w 5% 19 pin sip Reference Location
3D, 15H 1H, 6H 1D, 3F, 4D, 1OF, 11F
14A, 14E 1E,2D,4F,5F 12B, 12D, 13D, 14D, 15D 10E, 12E, 13F, 15F 14F, 16F, 11E,13E 8c, 1A, 3A 3B, 4H, 6B, 7D, 9B, 9E, 15A 3C, 4c, 6C 15B, 13B 1F, 14B, 7C, 8E 2A 4A, SA, 7B, 8B, llc, 12c 13c, 14C 11D 6D 14H 5c 8E, 9E, 2H 1D, 2H 2c 1C, 2c 7E, 2A 1c, 2c 9E 16A 15A
65082 Game Logic PCB Assembly (continued)
Part Number Description
51-0804 23-4933 23-4635
21-4015
20-4614 20-4005 72-3025 72-3042 45-3036 61-8641 61-8962 77-3374 61-8645
61-8935 61-8069 61-8157
21-4621 49-5138
59-5064 23-4667 48-9143-81 48-9143-92 48-9143-83 48-9143~-94 48-9143-085 48-9143-66 res., 6.8K 1/4w 5% 108 pin sip cap, .@1 uf ceramic disc cap, .1 uf ceramic disc
cap, 6.8 uf 25v tant. dip
cap, 33 uf 25v electrolytic cap, 470 uf 1@v electrolytic dip shunt jumper paks 16 pin dip switch 8 pos. crystal, 11.289 connector 1% pin molex dip sockets 16 pin low profile print. circuit board dip socket 24 pin low profile
dip socket 40 pin low profile dip socket 14 pin low profile dip socket 18 pin low profile
cap, 1 uf 25v dip tant res, 220 v 1/4 w 5%
res, 18ohm 1/4w 5% cap, 330 pf cer. disk 2716 EPROM programmed SPL6A-1 2716 EPROM programmed SPL7A-1 2716 EPROM programmed SPL8A-1 2716 EPROM programmed SPLA9A-1 2716 EPROM programmed SPL19@A-1 2716 EPROM programmed SPL11A-1
65082 Color Adapter PCB Assembly
Part Number Description
48-2086 48-2305 48-2321 48-2079 48-2341 48-2333 20-4015 59-5136 59-5193 23-4033 61-8283 61-8127 77-3373-14 Ic 74151 IC 74LS74 IC 74LS139 Ic 74148 IC 74LS86 IC 74LS174 6.8 uf dipped tantalum capacitor resistor 338 omega 1/4 w 5% 9 pin sip resistor pac 1K omega -@1 uf ceramic disc capacitor 1@ pin male molex connector 14 pin socket stan profile w/ lock printed circuit board Reference Location
14A 1D A/R per assy drawing 1c, 6E, 15D, 13F Ic 2c 16H 4B, 19D, 118 16A 1D 16C, 16E 5C, 6D, 14H
11D,6A,7A,8A 9A, 190A, 11A 2A 16B 4A 5A 7B 8B llc 12c 13¢ 14c c45, C52 R209, R311 at 5D R3090-R388 5D
Reference Location
5A, 5B, 5C 1A 2A 2B Ic 6A 6B cl Rl thru R16 3A, 3B, 3C c2 c4 C5 C6 P2 Jl
Electro Home Monitor Power Cord Assembly
Part Number Description
61-8056 molex plug 93-99-2022 61-8654 molex pins 92-69-2118
Main Harness
Part Number Description
61-8843 molex 6 pin flat wafer connector 61-8889 molex 4 pin plug 61-8039 molex 3 pin receptacle 61-8207 molex 15 pin receptacle 61-8113 molex 19 pin flat connector 61-8057 molex 2 pin receptacle 61-8958 molex 3 pin plug 61-8208 molex 12 pin flat wafer connector 61-8308 15 pin cinch edge connector 61-8399 dual 22 pin cinch edge connector black wire 18 gauge brown wire 18-22 gauge red wire 18 gauge orange wire 18 gauge yellow wire 18 gauge green wire 18 gauge blue wire 18-22 gauge violet wire 18 gauge grey wire 18-22 gauge white wire 18 gauge blue on black wire 18-22 gauge blue on green wire 18-22 gauge black on yellow wire 18 gauge black on orange wire 18 gauge black on violet wire 18 gauge red on green wire 18-22 gaige yellow on green wire 18-22 gauge black on grey wire 18-22 gauge red on white wire 18-22 gauge green on white wire 18-22 gauge violet on white wire 18-22 gauge orange on white wire 18-22 gauge yellow on blue wire 18-22 gauge white on grey wire 18-22 gauge red on grey wire 18-22 gauge green on grey wire 18-22 gauge white on brown wire 18-22 gauge green on brown wire 18-22 gauge Reference Location
monitor monitor
Reference Location
99-50-3101
Electro Home Monitor Power Cord Assembly (continued)
Reference Part Number Description Location
61-8311 molex pin 98-50-9116 61-8318 molex pin #8-83-8304 61-8954 molex pin (male) #2-69-2118 61-8055 molex pin (female) 92-89-1118 88-4002 Panduit tie wrap panduit tie clamp PLC-51-58 88-4005 1/8" shiring tubing
Power Supply Harness
Part Number Description
61-8058 molex 3 pin plug 61-8039 molex 3 pin recept. 61-8954 molex pin (male) 61-8055 molex pin (female) 88-4002 panduit tie wrap 4 in. black wire 18 gauge white wire 18 gauge red wire 18 guage green wire 18 guage
Isolation Transformer Harness
Part Number Description
61-8058 molex 3 pin plug 61-8839 molex 3 pin recept. 61-8054 molex pin (male) 61-8055 molex pin (female) 88-4002 panduit tie wrap 4 in. 61-8313 butt splice (red) black wire 18-22 gauge white wire 188-22 gauge green wire 18-22 guage
Spectar Universal Coindoor Harness
Part Number Description
61-8058 molex 3 pin plug 93-09-2032 61-8312 panduit terminal D18-188 61-8054 molex pin (male) 61-8313 butt splice (red) 88-4602 panduit tie wrap N/A red wire 188-22 gauge N/A green wire 18-22 gauge N/A blue wire 18-22 gauge
Control Panel Harness
Part Number Description
61-8695
88-4082 61-8854 molex 15 pin plug panduit terminal D18-188 violet on white wire 18-22 gauge green on white wire 18-22 gauge red on green wire 18-22 gauge green on blue wire 18-22 gauge orange on white wire 18-22 gauge red on white wire 18-22 gauge yellow on green wire 18-22 gauge green wire 18 gauge panduit tie wrap molex pin (male)