CATHODE RAY TOMES

Pole Position TM-218 4th Printing (Bad Scan)

Pole Position (World) (Namco, 1982) · Technical Manual · 85 pages · 51 sections · original scan

Page 1

Operation, Maintenance, and Service Manual

Complete with Schematics an

d Illustrated Parts Lists

Page 2

Operation, Maintenance, and Service Manual

Complete with Schematics

and Illustrated Parts Lists

@ *Pole Position is engineered and designed by Namco Ltd. Manufactured under license by Atari, Inc.

Page 3

Pole Position

© 1982 by Atari, Inc. All rights reserved. No part of this publication may be reproduced by any mechanical, photographic, or electronic process, or in the form of a phonographic recording, nor may it be stored in a retrieval system, transmitted, or otherwise copied for public or private use, without permission from the publisher. The game play, all graphic designs, this technical manual, its accompanying schematic diagrams, and the display manual are protected by the U.S. Copyright Act of 1976. This Act provides for increased penalties for violating federal copyright laws. Courts can impound infringing articles while legal action is pending. If infringers are convicted, courts can order destruction of the infringing articles. In addition, the Act provides for payment of statutory damages of up to $50,000 in certain cases. Infringers may also have to pay costs and attorneys’ fees, fines up to $25,000, and face an imprisonment of up to one year. Atari will aggressively enforce its copyrights against any infringers. We will use all legal means to immediately halt any manufacture, distribution, or operation of a copy of video games made by us. Anyone who purchases such copies risks forfeiting such a gam ;

Published by: ATARI, INC. 790 Sycamore Drive P.O. Box 906 Milpitas, California 95035

Lithographed in the U.S.A 2M

Page 4

& Pole Position

Notice Regarding Non-ATARI Parts

WARNING

Use of non-ATARI parts or modifications of your ATARI® game circuitry may adversely affect the safety of your game, and may cause injury to you and your players.

You may void the game warranty (printed on the inside back cover of this manual) if you do any of the following:

@ substitute non-ATARI parts in the game @ modify or alter any circuits in the game by using kits or parts not supplied by Atari.

INTERFERENC

to licensed communications services is not permitted by the Federal Communications Commission (FCC). If you suspect interference from an ATARI® game at your location, check the following: @ all green ground wires in the game are properly connected as shown in the the game wiring diagram @ the power cord is properly plugged into a grounded 3-wire outlet @ the game PCB is properly installed within the Electromagnetic Interference (EMI) cage @ the EMI Shield PCB is properly installed and in series with the game PCB harness. Refer to Figure 3-18 to make sure that the game PCB and the Shield PCB are correctly installed. If you are still unable to solve the interference problem, please contact ATARI Customer Service. See the inside front cover for service in your area. ~_A

Page 5

Pole Position

Table of Contents

1 Set Up Procedures New Features ........... 002.00 cess eee Inspecting theGame ... Leveling the Sit-Down Cabin * Space and Power Requirements .

  • Installation Requirements. . .
  • Selecting the Voltage Plug Locating the Switches ....
  • Power On/Off Switch .
  • Utility Panel Switches .
  • Option Switches .......
  • Memory Back-Up Jumper . Setting the Option Switches .. Performing the Initial Self-Test. Game Play ...
  • Attract Mode
  • Play Mode ....
  • High-Score Mode ..
  • Hints for Game Play pom>

m

zom

2 Self-Test Procedure A. Comments on Troubleshooting B. Performing the Self-Test

3 Maintenance, Repair, and Parts Cabinet-Mounted Assemblies Player Controls .......... Fluorescent Tube and Speaker Repla Video Display ...............00- Utility Panel. . Coin Doors ....... Printed-Circuit Boards .. Power Supply Assembly rOnmooOD>

Glossary of Terms ....................0.. 00.0 ccc cee cece eee 1-7

1-7 1-7

Page 6

Figure 1-1 Figure 1-2 Figure 1-3 Figure 1-4

Figure 1-5 Figure 2-1 Figure 2-2 Figure 2-3 Figure 2-4

Figure 3-1 Figure 3-2 Figure 3-3 Figure 3-4

Figure 3-5 Figure 3-6 Figure 3-7 Figure 3-8

Figure 3-9 Figure 3-10 Figure 3-11 Figure 3-12

Figure 3-13 Figure 3-14 Figure 3-15 Figure 3-16

Figure 3-17 Figure 3-18 Figure 3-19 Figure 3-20

Figure 3-21 Figure 3-22 Figure 3-23 Figure 3-24

Table 1-1 Table 1-2 Table 1-3 Table 1-4

Table 2-1 Table 2-2 Table 2-3 Table 2-4 Pole Position

List of Illustrations

Game Overview, Upright Cabinet . 1-2 Game Overview, Sit-Down Cabinet 1-3 Leveling the Sit-Down Cabinet . . oe 45 Location of Game Switches. ............ 0.6 cece cece eee 1-6 Self-Test Display... 0.6... 6. cc cece eee tenn Self-Test Screen 1: Upright Test Passes a Self-Test Screen 1: Sit-Down Test Passes Self-Test Screen 1: Test Fails a Self-Test Screen 2..... 0.60. cece ee cence eee eee eens

Illustrated Parts Lists Cabinet-Mounted Assemblies, Upright Cabinet . . 3-2 Cabinet-Mounted Assemblies, Sit-Down Cabinet 3-4 Control Panel .. 37 Control Panel Assembly ..........6 060 c cece cece eee eee 38 Steering-Wheel Control Assembly ............ 00s eee eee 3-10 Steering-Wheel Control Screw Adjustment . -. 312 Steering-Wheel Control Orientation . wee OB Gear-Shifter Control Assembly. .............00 0. cece eee 3-14 Foot-Pedal Control Assembly ..............0. 0c eee ee eee 3-16 Foot-Pedal Cable Rewinding 3-18 Fluorescent Tube and Speaker Board Removal, Upright Cabinet 3-20 Fluorescent Tube and Speaker Board Assembly Upright Cabinet 3-21

Sit-Down Cabinet Speaker Removal ...............00e eee 3-22 Video Display ...............-5 .. 325 Utility Panel Assembly . -. 326 Vertically Mounted Coin Door... ....s.scssscseseeeeseeeee 3-28

American-Made Coin Door..... 2.0.0... cece eee eee eee eee 3-31 Removing the Printed-Circuit Boards ...... Central Processing Unit Printed-Circuit Board Assem ly. .. 3:36 Pole Position Video Printed-Circuit Board Assembly.......... 3-44

Regulator/Audio 11 PCB Assembly, U.S.-Built Cabinet ......... 3-49 Regulator/Audio Il PCB Assembly, Ireland-Built Cabinet . .. 3-50 EMI Shield PCB Assembly.......... .. 353 Power Supply Assembly . List of Tables

Switch Settings for Game and Price Options ................ Switch Settings for Game and Play Options . 19 Self-Test Procedure ...............6 1-10 Qualifying Lap Information .............. 0c cece eee eee ee 1-13

Locating Failed Components on the Video PCB ............ 2-2 Locating Failed Components on the CPU PCB 2-2 Locating the Failed ROM ................0- - 23 Locating the Failed RAM .......... 000s cere eee eee eee 2-4

Page 7

Pole Position

vi

NOTICE

This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual, may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of FCC Rules, which are designed to provide feasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area is likely to cause interference in which case the user, at his own expense, will be required to take whatever measures may be required to correct the interference.

Page 8

@ set-Up Procedures

How to Use this Manual

This manual, written for game operators and service technicians, describes the Pole Position game. The manual contains information about the Upright and Sit-Down Pole Position cabinets. Whenever information is unique to the Upright

cabinet, this symbol appears: ]

Whenever information is unique to the Sit-Down

cabinet, this symbol appears: f

Wherever information is unique to /reland-Built

games, this symbol appears: *

x we > as PS a51/

OV AK ke by Ki

am Chapter 1 describes new features, game setup, settings of option switches, self-test procedures, and game play. Chapter 2 contains self-test procedures. Chapter 3 details maintenance, repair, and parts information. A glossary of terms is in the back of this manual for your convenience. In addition, schematic diagrams of the game circuitry are included with this manual. Figures 1-1 and 3-1 illustrate the Upright game cabinet; Figures 1-2 and 3-2 illustrate the Sit-Down game cabinet. Italicized lettering on these figures refers you to other places in the manual for information about specific cabinet parts.

>

Page 9

‘Set-Up Procedures

ATTRACTION PANEL, FLUORESCENT TUBE AND SPEAKER See Figure 3-11 or 3-12 Pole Position

% GAME IDENTIFICATION LABEL. (Serial number appears here on Ireland-Built games)

VIDEO DISPLAY a)

See Figure 3-14 = ACCESS PANEL > \ DASHBOARD

STEERING-WHEEL See Figure 3-1

CONTROL ASSY. p..) See Figure 35 = EMI CAGE if Ga (| Q See Figures 3-15 Peds) \ . and 3-23 igures 3-18, Was % 3:19 & 3-20 wae GEAR-SHIFTER ‘~ CONTROL ASSY. See Figure 38

UTILITY PANEL 4 REGULATOR!

See Figure 3-15 s 2 Sec rere 4 See Figures 3-18, gure 3-21 & 3.22

CONTROL PANEL See Figures 33 & 3-4

4 SPEAKER

See Figure 3-12 ES

COIN DOOR * See Figures 3-16 & 3-17

FOOT-PEDAL ASSEMBLY New Y See Figure 39

x Items with a serial number label on U.S.~Built cabinets POWER SUPPLY POWER ON/OFF SWITCH See Figure 3-24

WARNING

SHOCK HAZARD This game should only be connected to a grounded 3-wire outlet. If you have only a 2-wire outlet, we recommend you hire a licensed electrician to install a grounded outlet. You may receive an electrical shock if the game is not properly grounded!

Figure 1-1 Game Overview

Upright Cabinet

Page 10

Pole Position ‘Set-Up Procedures

@ % GAME IDENTIFICATION LABEL

(Serial number appears on exterior of rear access panel of Ireland-built games)

  • GAME PCBs See Figures 3-18, UTILITY PANEL ASSY. “> 3-19 & 3-20 See Figure 3-15 SPEAKER EMI CAGE See Figure 3-13 See Figures 3-18 & 323 “> ATTRACTION PANEL See Figure 3-2

ACCESS PANEL

+ REGULATOR! AUDIO II PCBs See Figures 3-18, 3-21 & 3-22 ) POWER ON/OFF SWITCH % POWER SUPPLY CAPACITOR See Figure 3-24 See Figure 3-24 VIDEO DISPLAY See Figure 3-14

STEERING-WHEEL CONTROL ASSY. See Figure 3-5

GEAR SHIFTER CONTROL ASSY. See Figure 3-8

CONTROL PANEL See Figures 33 & 3-4

COIN DOOR See Figures 3-16 & 3-17

WARNING

SHOCK HAZARD This game should only be connected to a grounded 3-wire outlet. If you have only a 2-wire outlet, we recommend you hire a licensed electrician to install a grounded outlet. You may receive an electrical shock if the game is not properly grounded! ACCELERATOR & BRAKE See Figure 3-9

x Items with a serial number label on U.S.-Built cabinets

Figure 1-2 Game Overview Sit-Down Cabinet

4-3

Page 11

Set-Up Procedures Pole Position

A. New Features B. Inspecting the Game

The Pole Position game has many new features. Even if you are familiar with ATARI® games, you should note these important differences: Please inspect your game carefully to ensure that it was delivered to you in good condition.

@ Electromagnetic Interference (EMI) Cage in U.S.-Built Cabinets Only. Games built after December 1, 1982, will have the CPU and Video printed-circuit boards (PCBs) mounted inside this cage. The EMI cage reduces interference from the game to television and radio receivers. See Figure 3-18 for details. @ American-Made Coin Door. Your game may be equipped with a new coin door. This door is very similar to the vertically mounted coin door, but does not have lockout coils. When ordering parts for your coin door, please check coin door illustrations in Figures 3-16 and 3-17 carefully to make sure you are ordering the correct part number. @ Steering-Wheel Control. This steering wheel is designed to provide a more realistic response from the race car on the display. @ Foot-Pedal Control (Accelerator and/or Brake). These pedals have been redesigned to accommodate a snap-action switch for the brake anda potentiometer, turned by a spring and cable, for the accelerator. @ Metal Attraction Panel on SitDown Game Cabinet. The metal attraction panel mounted on top of the cabinet entices players with its Formula-1 racing graphics. @ Quadraphonic Sound in Sit-Down Cabinet. Four 4-ohm, 6-ounce, high-fidelity speakers (two under the control panel; two behind the seat) surround the player with the exciting and realistic sounds of Gran Prix racing. New features and other major parts of the game are shown in Figures 1-1 and 1-2. Throughout this manual, wherever a new feature is mentioned, you will see this symbol: . a

1-4

WARNING To avoid electrical shock, do not plug in the game until the procedures in Sections B, C, and D have been completed!

Examine the exterior of the game cabinet for dents, chips, or broken parts. Remove the screws that were used as extra security to seal the rear access panel. Unlock and open this panel and the coin door; inspect the interior of the game as follows: a. Ensure that all plug-in connectors (on the game harness) are firmly plugged in. Replug any connectors found unplugged. Do not force connectors together. The connectors are keyed so they only fit in the proper orientation. A reversed edge connector may damage a PCB and will void your warranty. b. Ensure that all plug-in integrated circuits are firmly plugged into their sockets on the printed-circuit boards (PCBs). c. Remove the tie-wrap that secures the coiled power cord inside the cabinet. Inspect the power cord for any cuts or dents in the insulation. Repair or replace it as required. Place the square black plastic strain-relief plate in the wood slot at the bottom of the rear panel opening. d. Note the game serial number printed on a label on the back of the cabinet. Verify that the same serial number is also on the Pole Position game PCBs, Regulator/Audio II PCBs, power supply, and video display. See Figures 1-1 and 1-2 for locations of the serialnumbered components. Please mention the serial number whenever you call your distributor for service. e. Inspect major subassemblies, such as the power supply, control panel, and video display. Make sure they are mounted securely.

WARNING

To avoid electrical shock, do not touch internal parts of the display with your hands or with metal objects held in your hands!

Page 12

Pole Position

  • For the Sit-Down cabinet, remove the metal attraction panel from the protective wrapping. Remove the three button-head screws and retainer on the front window. Place the attraction panel over the mounting holes. Reinstall the retainer and screws.

C. Leveling the Sit-

C. Leveling the Sit Down Cabinet

The Sit-Down cabinet rolls easily from location to location on 4-inch casters. To level the cabinet, lift the game up on one side. Place a block of wood, a book, or another object (that is at least 2-inches thick) under the raised cabinet. Partially unscrew the adjustable glides (see Figure 1-3) until they extend below the caster. Lower the game and lift it up on the other side; partially unscrew the adjustable glides. Lower the game. To prevent players from moving the game around, be sure to adjust all four glides.

ADJUSTABLE GLIDE “a

Figure 1-3 Leveling the Sit-Down Cabinet Set-Up Procedures

D. Space and Power Requirements

  • Installation Requirements

Power 250 W Temperature 0° to +38°C(+ 32° to + 100°F) Humidity Not over 95% relative Upright Cabinet Space Required Game Height 62 x 90 cm (25% x 35%, in.) 186 cm (72% in.) Sit-Down Cabinet 165 x 64 cm (65 x 25% in.) 194 cm (76 in.) Space Required Game Height

  • Selecting the Voltage Plug
WARNING SHOCK HAZARD

This game should only be connected to a grounded 3-wire outlet. If you have only a 2-wire outlet, we recommend you hire a licensed electrician to install a grounded outlet. You may receive an electrical shock if the game is not properly grounded!

The power supply used in this game operates on the line voltage of almost any country in the world. The power supply comes with either one, two, or three separate voltage-selection plugs. Plug voltages and wire colors are 100 VAC (violet wire color), 120 VAC (yellow wire color), 220 VAC (blue wire color), and 240 VAC (brown wire color). Before plugging in your game, check your line voltage. Next, check the wire color on the voltageselecion plug that is plugged into the game’s power supply. Make sure the voltage-selection plug is correct for the voltage of your location (see Figure 3-24). Now, plug the game into a grounded 3-wire outlet.

Page 13

Set-Up Procedures.

E. Locating the Switches

CAUTION

Do not depress the accelerator or brake pedal when turning on the game or switching to the Self-Test Mode. This will cause faulty program initialization and incorrect action of the player controls. Pole Position

  • Power On/Off Switch

The power on/off switch is located on the back of the Upright cabinet on the lower left side. On the Sit- Down cabinet the power on/off switch is located on the lower left side of the cabinet (see Figure 1-4).

OPTION SWITCHES SWITCH AT 9JA (Game and price) SWITCH AT 9L (Game and play)

information.

JUMPER AT 6B (Memory back-up) See CO-218-01 for NAMCO PCB UTILITY PANEL ASSY. See Figure 3-15

POWER ON/OFF SWITCH

Figure 1-4 Location of Game Switches

Page 14

Pole Position

  • Utility Panel Switches The volume control(s), self-test switch, coin counter(s), and auxiliary coin switch are located on the utility panel in both the Upright and Sit-Down cabinets (see Figure 3-12). The utility panel is located inside the upper coin door. The volume control(s) adjust the level of sound produced by the game. The Sit-Down cabinet has four volume controls: one for each speaker. The Upright cabinet has two volume controls: one for each speaker. The self-test switch is used to enter and exit the Self-Test Mode. The coin counter(s) record the number of coins entered into the game. The auxiliary coin switch is used to credit the game without activating the coin counter(s).
  • Option Switches Option switches are located on the game CPU PCB (see Figure 1-4). Refer to supplement CO-218-01 for switch locations if your game has NAMCO PCBs. a. Game and price options are at CPU PCB location QJA. b. Game and play options are at CPU PCB location 9L.
  • Memory Back-Up Jumper The memory back-up jumper is at CPU PCB location 6B. Position this jumper to the on setting. The memory back-up jumper is positioned on the off setting when shipped from the factory to prevent leakage and to provide longer life for the battery at location 6A on the CPU PCB. The jumper must be positioned to the on setting so that the battery can provide power to the CMOS memory. This memory stores the high-score table and operator statistics. ‘Set-Up Procedures

The jumper does not affect game play. We recommend you position this jumper to the off setting when you expect extended downtime.

FE. Setting the Option Switches

Settings of the game option switches are explained in Tables 1-1 and 1-2. Options preset at the factory are shown by the <4 symbols. However, you may change the settings according to your individual needs. To verify option-switch settings, first set the power on/off switch to the off position and then to the on position. Next, set the self-test switch to the on position. Compare the information on the screen to the option switch settings listed in the tables in this section. Then set the self-test switch to the off position. Table 1-1 describes the switch settings for options relating to game price, coin mechanism multipliers, number of laps per game, and number of seconds per lap. These switches are on the game CPU PCB at location QJA. The multipliers (QJA switches 1-5) determine the value of the coin mechanisms to the game’s logic. A coin mechanism is a device on the inside of the coin door that inspects the coin to determine if the correct coin has been inserted. The mechanism either accepts or rejects the coin. The coin door has two coin mechanisms. The basic unit of measurement is a coin worth $.25 or 1 DM, which equals a multiplier of x1. For example, if you have a 2 DM/1 DM coin door, you may want to set the left multiplier at x2 and the right multiplier at x1.

N LAN

I, x Net

Page 15

Set-Up Procedures Pole Position

NOTE
CoinOptionInterconnectAssembly

J55A-P55A permits a coin placed in either coin mechanism to register in the same coin counter. The cable connector is located between the coin door harness and the main harness (see the Coin Op-

tionInterconnectWiringDiagramin
SP-218).Whenitisused,leftcoin

mechanism option switches at 9JA apply to both coin mechanisms. 'f you want different options for the left and right coin mechanisms, remove Coin

OptionInterconnectAssemblyJ55A-

P55A and connect J55 directly to P55. \f you have NAMCO game PCBs, refer to CO-218-01 for the location of the option switches.

Table 1-1 Switch Settings for Game and Price Options

Settings of 8-Toggle Switch on Pole Position CPU PCB (at 9JA)

87654321Option

On 4 racing laps * Off 3 racing laps <<

OffOff90 seconds per lap <
OffOn100 seconds per lap

On = Off 110 seconds per lap

OnOn120 seconds per lap *

Right Coin Mechanism

OffOff1 coin for 1 credit <
OffOn2 coins for 1 credit *
OnOff3 coins for 2 credits
OnOn4 coins for 3 credits

Left Coin Mechanism

OffOffOff1 coin for 1 credit <
OffOffOn1 coin for 2 credits
OffOnOff1 coin for 3 credits
OffOnOn2 coins for 1 credit *
OnOffOff3 coins for 1 credit
OnOffOn3 coins for 2 credits
OnOnOff4 coins for 3 credits *
OnOnOnFree Play

“4Manufacturer’s recommended settings for Upright cabinet % Manufacturer’s recommended settings for Sit-Down cabinet *This option setting can be changed to 1 coin for 6 credits by changing the program PROM (136014-160). Contact your distributor for further information.

Page 16

Pole Position

NOTE

pr) We recommend that game difficulty for

the race laps (EXTENDED RANK) and the qualifying lap (PRACTICE RANK) be increased periodically. These changes will ensure that Pole Position continues to offer maximum excitement and challenge. Except in locations with extremely skillful and advanced players, these settings should not be increased more than one level per month. ‘Set-Up Procedures

Table 1-2 contains option-switch settings for Attract Mode sound and speed (kilometers or miles per hour). These switches are on the game CPU PCB at location OL. Pole Position leaves the factory with option switches set at the manufacturer's recommended difficulty level. The game will be exciting and challenging for players at these settings. Table 1-4 lists the manufacturer’s recommended qualifying lap times. Table 1-5 lists option-switch settings for additional qualifying lap times. Table 1-6 provides switch settings for racing lap times.

Table 1-2 Switch Settings for Game and Play Options

Refer to CO-218-01 for switch locations if your game is equipped with NAMCO PCBs.

Settings of 8 Toggle Switch on Pole Position CPU PCB (at 9L) 8 7 6 5 4 3 2 1 Option

Off On

Off On Attract Mode sound off Attract Mode sound on <

Kilometers per hour Miles per hour <

“4Manufacturer's recommended settings

1-9

Page 17

Set-Up Procedures

G. Performing the Initial Self-Test

This game will test itself and provide data to show that the game’s circuitry and controls are operating properly. The data is provided on the video display and speakers. No additional equipment is necessary. Wait at least 10 seconds after playing a game before switching to the Self-Test Mode. Otherwise, you may erase the top three scores in the high-score table or distort the statistics. All credits will be cancelled when you switch to self-test. Refer to Figure 1-4 for the location of the option switches and Figure 3-15 for the location of the selftest switch. Set the self-test switch to the on position (see Figure 1-5) to see the Self-Test Display in the Self-Test Mode. To exit the Self-Test Mode, set the self-test switch to the off position. Pole Position

The complete self-test procedure is explained in Chapter 2, B. Self-Test Procedure. \f a part of the test described in Table 1-3 fails, refer to Chapter 2. We suggest you perform the self-test procedure when you first set up the game, when you collect money from the game, when you change game options, or when you suspect game failure.

CAUTION

Do not depress the accelerator or brake pedal when turning on the game or switching to the Self-Test Mode. This will cause faulty program initialization and incorrect action of the player controls.

Table 1-3 Self-Test Procedure

Instruction Test Passes

|. Without touching the pedal(s), set the self-test switch to the on position. All credits will be cancelled.

. Press down on the accelerator pedal.

. Press down on the brake pedal of the Sit-Down cabinet.

. Turn the steering wheel clockwise, then counterclockwise.

.. Shift the gear shifter.

. Shift the gear shift, press the auxiliary coin switch, and activate the coin switches.

. Press the auxiliary coin switch.

  • To end the test, switch the self-test switch to off. Random symbols are displayed on the screen for about five seconds. The self-test display appears. RAMs and ROMs are tested. If the screen is different from the self-test display, or if there are sounds, refer to Chapter 2, Self-Test Procedure.

The numbers to the right of ACCEL increase from 00 to somewhere between 90 and AQ as you press down on the pedal. If the test fails refer to Chapter 2.

The numbers to the right of BRAKE switch from 00 to FF. For the Upright cabinet, the numbers to the right of BRAKE should always read 00. If the test fails, refer to Chapter 2.

Rotating the wheel clockwise causes the numbers to the right of STEER- ING to increase. Rotating the wheel counterclockwise causes the numbers to decrease. If the test fails refer to Chapter 2.

The words to the right of SH/FT change from LO (shifter up) to HI (shifter down) as you shift gears. If the test fails, refer to Chapter 2.

The numbers to the right of SOUND increase from 00 to 20, and a new sound is played with each number. Test all 20 sounds. If the test fails, refer to Chapter 2.

Game statistics appear (for a few seconds) at the bottom of the screen. Press the coin switch each time you want to see the statistics. To erase game statistics, simultaneously press down on the accelerator pedal and press the auxiliary coin switch twice. Statistics will be reset at /999/. To reset the high-score table, simultaneously press down on the accelerator pedal and change gear shifter from low to high. The high-score table will be reset and contain fictitious scores.

4-10

Page 18

Pole Position Set-Up Procedures

ALL RAMS GOOD ALL ROMS GOOD ACCELERATOR PEDAL — a - teeer ox ‘ROM OK STEERING sacet 00 —s BRAKE 00 WHEEL STEERING 00 = SHIFT LO <————— ceansurrten

SOUNDS LEFT COIN

MECHANISM

RIGHT COIN MECHANISM QUALIFYING LAP TIME NO. OF LAPS IN THE RACE

RACE DIFFICULTY LEVEL» ‘ ee Eb 12) EXTENDED RANK

PRACTICE QUALIFYING LAP DIFFICULTY LEVEL (See Table 1-2)

GAME AUTOMATICALLY STARTS* (When correct number of coins are inserted) THE COUNT STARTS AT 999(999) AND DECREASES. For example, if you play 10 games, the game subtracts 10 from 99.9, and the display shows 98.9 for the number of games played. (Disregard decimal points.)

NO. OF GAMES PLAYED NO. OF POINTS SCORED (x10) NO. OF SECONDS PLAYED NOT APPLICABLE

999. 999. 999, 999, 999. 999. 999. 999, 999. 999, 999, 999. 999. 299. _{— | a | rn | NO. OF SECONDS THAT GAME /

HAS BEEN POWERED ON by OF GAMES IN WHICH

NO. OF GAMES IN WHICH PLAYER REACHED FINISH LINE PLAYER HAS QUALIFIED NO. OF GAMES THAT REACHED NO. OF GAMES THAT REACHED THIRD EXTENDED LAP . FIRST EXTENDED LAP *If screen displays MANUAL START, suspect the game harness. NO. OF GAMES THAT REACHED Refer to the Schematic Package. SECOND EXTENDED LAP

Figure 1-5 Self-Test Display

Page 19

‘Set-Up Procedures

H. Game Play

Pole Position is a one-player game using a color raster-scan video display. The game action takes place at Fuji Speedway in Japan. The country around the speedway consists of green meadows, hills, and snow-capped Mt. Fuji. The player drives a Formula-1 race car on the Fuji Speedway. Player controls consist of a steering wheel, a two-position gear shifter, and accelerator and brake pedals on the Sit-Down cabinet (accelerator only on the Upright cabinet). The object of the game is to finish the qualifying lap as quickly as possible. If the player beats the clock, he qualifies for the Gran Prix at Fuji Speedway; if not, he drives out the remainder of his time along the qualifying course. As a qualifier, the driver is ranked according to his qualifying lap time, from position one (the pole position) to position eight. The player then races against the clock and other cars to finish the four laps (operator-selectable option) of the race as fast as possible and to achieve the highest score possible. The player earns points for passing cars, driving on the track, and finishing the race with time remaining. He is rewarded with an extended-play lap for completing a lap. Pole Position has four modes of operation: Attract, Play, High-Score, and Self-Test. Self-Test is a special mode for checking the game switches and computer functions. You may enter the Self-Test Mode from any other mode. However, all credits will be cancelled. Pole Position

  • Attract Mode

The Attract Mode begins when you set the power on/off switch to on or after the Play, High-Score, or Self-Test Modes. The Attract Mode ends when the correct amount of credit for a game is inserted or when the Self-Test Mode begins. When the Attract Mode begins, the game displays a picture with the words POLE POSITION flashing at the top of the screen. A map of Fuji Speedway is displayed in the center of the screen. Within the map are the words FUJ/ SPEEDWAY and 1 LAP 3459M. At the bottom of the screen is the copyright message. Then, the Attract Mode simulates game play. Eight cars are at the starting line. The player's car, located in the eighth position, flashes on the screen. The starting lights flash from red to green and the race Starts. The race continues until the player's car crashes into another car and explodes into a red ball of fire. Then, the car reappears on the screen and continues down the track until it hits a sign along the side of the road. Again, the car explodes. During this sequence, the message GAME OVER appears in the center of the screen. Finally, the Attract Mode displays the High-Score Table. The fastest lap time, average game speed, and prize winners appear at the top of the screen. Below this information is a list of the six highest scores. Opposite each score are the initials of the player who achieved that score.

  • Play Mode The Play Mode begins when the correct amount of credit for a game is recorded. The game starts with the player's car behind the starting line and 90 seconds on the clock. (See Section E to select a different clock setting.) The car must finish the qualifying lap within 73 seconds to be in the race. If the player does not qualify, his car continues on the track until 90 seconds are used up.
Page 20

Pole Position

Table 1-4 Qualifying Lap Information

POSITION QUALIFYING LAP TIME* BONUS POINTS

158" 504000
260” 002000
362” 001400
464” 001000
566" 00800
668” 00600
770" 00400
873” 00200

*In seconds and hundredths of a second The above times apply to manufacturer's recommended settings. Just before the race begins, the player's car (flashing on the screen) is placed at the starting line with seven other cars. The position of the car depends on the qualifying time as shown in Tables 1-4 or 1-5. The starting lights flash from red to green, and the race begins. Racing hazards are other racing cars, sharp turns, and road signs. As the race progresses, more cars appear on the track. If the driver's car hits another car or a road sign, the driver’s car is destroyed in an explosion. The driver's car reappears in a few seconds and the race continues. Driving through wet puddles or off the track slows down the driver's car. Racing into the first turn, the driver must let up on the accelerator slightly to make the corner. Road signs flash along the side of the track. Depending on how well the player manipulates the controls, he can either roar through the hairpin turns like a champion or spin out in a flaming crash. He jockeys for position with the other racers, while keeping his eye on the clock at the top of the screen. When his time runs out, the race is over. The top score achieved by a player appears at the top of the screen. The time alloted for the lap is displayed under the top score. Increasing lap time (in seconds and hundredths of a second) and the speed of the car appears last. ‘Set-Up Procedures

  • High-Score Mode The High-Score Mode begins when a player has earned one of the 300 highest scores. The player has one minute to record his initials. A player rotates the steering wheel to locate his initial. He presses a foot pedal to put his initial on the screen. The third time he presses the pedal his initials are transferred into the high-score table.
  • Hints for Game Play Avoid puddles and the sides of the track because these slow you down. Accelerate and stay ahead of other racers. Stick to the inside of the track to make the corners. ¢ Successful completion of a turn depends on braking skill. © When sliding, steer into the skid.
Page 21

Pole Position Set-Up Procedures

Table 1-5 Switch Settings for Qualifying Lap Times

9LSelf-TestLevel
OptionPracticeofBeat This Many Seconds
‘SwitchesRankDifficultyto Qualify for Position:

1 2 3 1 2 3 4 5 6 7 8

On Off OnFEasy66 68 70 73 75 77 80 82
Off Off OnE65% 67% 70 722 74¥2 76V2 79 81
On On OnH59% 61 63 66 68 70 72 75
On On Offio)59 61 63 65 67 69 ral 74
Off On Offc<58% 60 62 64 6 68 7 73
On Off OffB58 60 62 64 66 68 70 72
Off Off OffA57% 8659 61 63 65 67 69 ral
Off On OnGHard57 59 61 63 65 67 69 71

“4Manufacturer's recommended settings

Table 1-6 Switch Settings for Racing Lap Times

9LJA Self-TestTop SpeedNumber of Seconds

Option Option

Switches ‘Switch Extended 4 5 6 8 Goal Rank MPH KPH Lap1 Lap2 Lap 3 Lap4 Off Off Off Off 3 A 195 313 75 50 61 = Off Off Off On 4 A 195 313 7 53. 58 62 Off On Off Off 3 Cc 195 313 75 48 60 - Off On Off On 4 c 195 313 75 51 57 61 On Off Off Off 3 B< 195 313 75 46 59 = On Off Off On 4 Ba" 195, 313 75 49 56 60 On On Off Off 3 D 195 313 75 44 58 - On On Off On 4 D 195 313 75 47 55 59 Off Off On Off 3 E 225 360 75 48 60 - Off Off On On 4 E 225 360 75 51 57 61 On Off On Off 3 FE 225, 360 75 46 59 = On Off On On 4 F 225 360 75 49 56 60 Off On On Off 3 G 244 391 75 48 60 - Off On On On 4 G 244 391 7 51 57 61 On On On Off 3 H 244 391 75 46 59 - On On On On 4 H 244 391 75 49 56 60 “Manufacturer's recommended settings *Upright cabinet **Sitdown cabinet wv

Page 22

» Self-Test Procedure

NOTE

The reference designators for components in this chapter refer to games with Atari® PCBs. If you have Namco XQ PCBs, please refer to CO-218-01.

The following self-test procedures should be performed by a qualified electronic technician. This game tests itself when the self-test switch is set to the on position. If there is a failure, the game produces audiovisual aids to help you find the failing portion of the game. The self-test procedure included in Chapter 1 will help you decide if the game is working properly.

Pr Chapter

Page 23

Self-Test Procedure

A. Comments on Troubleshooting

When troubleshooting, first determine the symptom(s) of the failure. After determining the symptom, look over the wiring diagram and determine what assemblies could cause the failure. Could it be caused by the power supply, Regulator/Audio II printed-circuit board (PCB), or the video display? The next step is to check all harness wires and connectors to the suspected assembly. If you do not find a harness or connector problem, substitute an assembly known to be good for the suspected failing assembly. If the game functions properly, you have successfully isolated the failure. If it doesn’t, repeat the procedure with another assembly. When you have isolated the failing assembly, you must troubleshoot that assembly and make the necessary repairs. If the video display fails, we suggest that a qualified video-display technician handle the troubleshooting and repair. Be sure to refer to The Book—A Guide to Electronic Game Operation and Servicing, published by Atari, Inc., whenever you need help with the techniques, tools, and terminology associated with coinoperated electronic games. To effectively troubleshoot a game PCB, learn as much as you can about the PCB. The diagrams in the Schematic Package (included with the game) show the functions of the circuitry. Again, while troubleshooting a PCB, first determine the symptom of the failure, then locate the suspected area on the schematic diagram. Tables 2-1 and 2-2 are troubleshooting aids, which can be used to locate faulty components.

Table 2-1 Locating Failed Components on the Video PCB

Symptom Area PROM Custom RAM

ic Large Car Pictures 125,130 Large Sign Pictures 12K,13K,12L, 13L Smail Cars & Signs 12N,13N All Cars & Signs 12H,11N 13H ‘9OF,10F Alphanumerics 7N,8M 8N Raceway 2L,2M,2N,4L 3N Background 6N,5K Raceway & Background SL,6L Middle & Sides of Raceway 2B,2C,2D All Video 4D,7E,2F

Red NE

Green 11D Blue 1c Pole Position

Table 2-2 Locating Failed Components on the CPU PCB

Custom AtoD

Symptom Area PROM IC RAM Converter

Audio Voice 9c 9D Screech/Crash 9E Player’s Motor 12E,12F All Other Sounds 7L,11D TK,7d Inputs Brake and/or Accelerator By Steering 9K Option Switches 9K,9M All Other Inputs. 9M Control for Audio & Inputs 8H,9H Sync 7M High Scores 7E

B. Performing the Self-Test

This game will test itself and provide data to show that the game’s circuitry and controls are operating Properly. The data is provided on the video display and speaker. No additional equipment is necessary. Video game repair should only be performed by a qualified electronic technician. To begin the Self-Test Mode, set the self-test switch, which is located on the utility panel, to the on position.

CAUTION Do not depress the accelerator or brake pedal when turning on the game or switching to the Self-Test Mode. This will cause faulty program initialization and incorrect action of the player controls.
Page 24

Self-Test Procedure Pole Position

SELF-TEST SCREEN 1—Test Passes: SELF-TEST SCREEN 1—Test Fails: ) Upright Cabinet. If the test passes, the screen If the test fails, the screen may display the picture displays the picture in Figure 2-1, Upright Test in Figure 2-3, Test Fails. Passes. See Chapter 1, Section G, Performing the Initial Self-Test for a complete description of this picture. To see self-test screen two, set the self-test switch to off and immediately back to on.

PRACTICE RANK C AUTO START Figure 2-3 Self-Test Screen 1: Test Fails

ROM failure is indicated by the word ROM and a Figure 2-1 Self-Test Screen 1:

igu es! pair of alphanumeric characters displayed at the top

Upright Test Passes of the screen.

wo Table 2-3 Locating the Failed ROM

Sit-Down Cabinet. If the test passes, the screen displays the picture in Figure 2-2, Sit-Down Test Location on Location on ROM No. ATARI CPU PCB NAMCO CPU PCB Passes. See Chapter 1, Section G, Performing the Initial Self-Test for a complete description of this pic-

ture. To see self-test screen two, set the self-test07H6H
switch to off and immediately back to on.2iay
3aLaL
RAM OKROM OKa“3k™
STEERING 00SHIFT LO74e4u

coum @ ; a: COIN1 2COIN® 1CREDIT - COIN2 2CDINS ACREDIT “Not used TIME 120

GOAL 4

EXTENDED RANK B PRACTICE RANK C AUTO START

@ Figure 2-2 Self-Test Screen 1:

Sit-Down Test Passes

Page 25

Self-Test Procedure

RAM failure is indicated by the word RAM and a pair of alphanumeric characters displayed at the top of the screen. Table 2-4 lists the failed RAM chip, the printed-circuit board (PCB) the chip is on, and the chip’s location. Replace the failed RAM, and restart the test (set the self-test switch to off, and then to on).

NOTE The reference designators for components in this chapter refer to games with Atari® PCBs. If you have Namco PCBs, please refer to CO-218-01.

Table 2-4 Locating the Failed RAM Location on Location on

ATARI NAMCO

RAM No. CPU PCB Video PCB CPU PCB Video PCB

0, 20, 408F7H
1, 21, 417F7F
22, 42a5H
23, 43WWSF
2, 24, 448H6H
3, 24, 457H6F
26, 458K4H
27, 477K4F
4, 28, 483F7B
29, 494F7
5, 30, 503E8B
1, 514E8c
6TW7H
77K8H
87E4H

Steering failure is indicated by failure of the numbers to the right of STEERING to properly increase or decrease. As you rotate the wheel clockwise, these numbers should increase; as you rotate the wheel counterclockwise, they should decrease. If the test fails, suspect the Coupler PCB.

Accelerator failure is indicated by failure of the numbers to the right of ACCEL to increase as you press down on the pedal. If no numbers appear, suspect a bad A-D converter on the CPU PCB ora mechanical problem on the foot pedal assembly. Troubleshoot using the information in Chapter 3, Section B, and the game schematics.

2-4 Pole Position

Brake failure on the Sit-Down cabinet is indicated by failure of the numbers to the right of BRAKE to change as you press down on the brake pedal. On the Upright cabinet, brake failure is indicated by anything other than 00 appearing to the right of BRAKE. If the test fails, suspect a bad switch, improper mechanical adjustment on the foot pedal assembly, or no ground on the brake edge-connector pin in the harness. Gear-shifter failure is indicated by failure of the words to the right of SHIFT to change from LO (shifter up) to H/ (shifter down) as you shift gears. If the —_ fails, suspect loose connector wires or a bad switch. Sound failure is indicated by the absence of any sound when the coin switches or gear shifterare activated. Suspect a loose harness or connector wire, the volume control turned off, the custom audio I/O chip, or the Regulator/Audio I board. Troubleshoot using the game schematics. To see self-test screen two, set the self-test switch to off and immediately back to on.

SELF-TEST SCREEN 2:

A white crosshatch pattern appears on the screen (see Figure 2-4). Use this pattern for convergence (see the raster-scan video display manual).

Figure 2-4 Self-Test Screen 2

Page 26

w Maintenance, Repair, and Parts

This chapter details maintenance and repair information and provides information you need to order parts for your game. Common hardware (screws, nuts, washers, bolts, etc.) has been deleted from most of the parts lists. However, a parts list for the hardware to mount the printed circuit boards (PCBs) to the cabinet has been included. The printed circuit board (PCB) parts lists are arranged in alphabetical order by component. Each component subsection is sorted by reference designator. Other parts lists are arranged alphanumerically by Atari part number. In these parts lists, all A-prefix numbers come first. Following these are numbers in sequence evaluated up to the hyphen, namely 00- through 99-, then 000598-through approximately 201000-. When ordering parts, please give the part number, part name, number of this manual, and serial number of your game. This will aid in filling your order rapidly and correctly. We hope the results will be less downtime and more profit from your game. Atari Customer Service numbers are listed on the ”) inside front cover of this manual.

  • Chapter
Page 27

Maintenance, Repair, and Parts

A. Cabinet-Mounted Assemblies Pole Position

Manuals, Schematics, & Self-Test Label— See parts list on next page

Fluorescent Tube and Speaker See Figures 3-11 & 3-12 ee | (Ventilation grille) af N me) XI SN 7-6900402 _\ 03937101

(Tape)(Shield retainer)A038881-01

(Lock) 039817-01 039119-02 (isplay shield) (Access panel) 039376-01 Video Display See Figure ou fe (Access panel) A037701-01 037742.01

78-6900402.EMI Cage(Bracket)

See Figures 3-18 & 3:23

rene)yy,3Game PCB Assy.

‘See Figures 3-18, A039420-01 , (Dashboard/decal) 518, & 3:20 Steering-Wheel a

Control Assy.AQGear-shitter Control Assy.‘03045901
See Figure 3-5.See Figure 38(Main har. assy)\

4039499-01

178034024Eontrol Panel Rasy.(Main harn. ass
(T-Moiding)See Figures 3:3 & 3-4pelvis '%

aaenoyo01 (Main harn. assy.)

Utility Panel(Speaker)Regulator! Audio Il
See Figure 3-15039144-01PCB Assy.

an (Speaker grille) y See Figures 25 3-21 & 3:22 Coin Door Assy. S —

See FiguresAg99460-01x‘ra04e-001
3-16 & 317(Power harn. assy.))(Caster)
038870-01Power Supp!J=
(Coin box enclosure—KSee Figure ves\°A037453-04

not shown) (Power cord) 038091-01 A037454-04

(Coin box—not shown)A039353-01(Power cord)

178034-025 (Cabinet assy) A037470-01 (T-Molding) A039353-02 (On/off switch assy.) (Cabinet assy.) 00999201

maaoniFootPedal Assy.A030353-03(Onloff switch cover)

(Glide) See Figure 3-9 (Cabinet assy.)

Figure 3-1 Cabinet-Mounted Assemblies U.S.-Built Upright Cabinet A039352:01 H Ireland-Built Upright Cabinet A039352-02 H (

3-2

Page 28

Pole Position Maintenance, Repair, and Parts

Cabinet-Mounted Assemblies Upright Cabinet Parts List Assemblies and components in the following parts list are shown in Figure 3-1.

Part No. Description For U.S.-Built Upright Cabinet A037453-04 Strain-Relief Power Cord (U.S. and Canada) A037701-01 Electromagnetic Interference Cage (includes guides) A039353-01 Cabinet Assembly (includes glides and PCB retainers, but not access panel) A039459-01 Main Harness Assembly (for U.S. PCB) For Ireland-Built Upright Cabinet A037454-04 Strain-Relief Power Cord (Austria, Belgium, Chile, Denmark, Finland, France, Germany, Greece, Indonesia, Italy, Netherlands, Norway, Spain, Sweden, and Uruguay) A039353-02 Cabinet Assembly (includes glides and PCB retainers, but not access panel) (for NAMCO PCB) A039353-03 Cabinet Assembly {includes glides and PCB retainers, but not access panel) (for Atari® PCB) A039459-02 Main Harness Assembly (for Atari® PCB) A039499-01 Main Harness Assembly (for NAMCO PCB) 03774201 Printed Circuit Board Mounting Bracket 039119-02 Rear Access Panel 72-1620S #6-32 x 1.25-Inch Pan Head Machine Screw 75-016S #6 Flat Washer For U.S.-Built and Ireland-Built Cabinets A037470-01 Power On/Off Switch/Mounting Plate Assembly A038881-01 Lock Assembly (for rear access panel) Acceptable substitute is part no. A038881-03 A039420-01 Dashboard Housing and Decal Assembly A039460-01 Power Harness Assembly A039576-01 Coin Option Interconnect Assembly The following nine items are technical information supplements to this game: CO-218-01 Pole Position Supplement (for NAMCO game PCB removal) SP-218 Pole Position Schematic Package (for Atari® game PCBs) or SP-219 Pole Position Schematic Package (for NAMCO game PCBs) S$T-218-01 Pole Position Label with Self-Test Procedure and Option Switch Settings (for Atari? game PCBs) ‘ST-219-01 Pole Position Label with Self-Test Procedure and Option Switch Settings (for NAMCO game PCBs) TM-160 Service Manual for 19-Inch Electrohome Color Raster-Scan Display (use with part no. 92-049) M-201 Service Manual for 19-Inch Wells-Gardner Color Raster-Scan Display (use with part no. 92-055) T™-218 Pole Position Operation, Maintenance, and Service Manual TM-220 Service Manual for 19-Inch Matsushita Color Raster-Scan Display (use with part no. 139003-1004) 78-3201 Adjustable Glide 78-6900402 Vinyl Foam Single-Coated Adhesive Tape, %-Inch Wide x %;-Inch Thick (48 inches required; used on top edge of video display shield, and on top edge of contro! panel) 78-6900404 Vinyl Foam Single-Coated Adhesive Tape, %-Inch Wide x %-Inch Thick (48 inches required; used on top and bottom of attraction panel) 009992-01 On/Off Switch Cover 03733201 Ventilation Grille 038091-01 Molded Coin Box (not shown) 038770-01 Metal Coin Box Enclosure (not shown) Acceptable substitute is part no. 038781-01 039144-01 Speaker Grille 039371-01 Video Display Shield Retainer 039376-01 Rear Access Panel (does not include lock) 039417-01 Video Display Shield with Graphics 148001-001 6- x 9-Inch Oval, 4-Ohm, 15 W Unshielded High-Fidelity Speaker (located on front panel) 171034-xxx Over/Under Coin Door Assembly Acceptable substitute is part no. 171027-001. 178034-024 %-Inch Black Plastic T-Molding (located on side panels) 178034-025 2,-Inch Black Plastic T-Molding (located on front panel) 178048-001 2-Inch Rigid Caster

Page 29

Maintenance, Repair, and Parts Pole Position

‘A039465-02 (Main harn. assy.) A039465-01 A039101-01 (Main harn. assy.) (Cabinet assy) A039245-01 *® A039101-02 (Main harn. assy.) (Cabinet assy.) Game PCB Assy. A039101-03 See Figures 3-18, 3-19 & 3-20 (Cabinet assy.)

037990-01 (Vent. Grille) veo =f 1 (Speaker) 78034034 03914501 (EMokéne) A037701-01 (Speaker grille) (EMI cage) See Figures 0391 3-18 & 3-23 (Grille) 038641-01 a 148001-001 (Vent. grille) Uo (Speaker) pa r= (Lock) 178034-024 (T-Molding)

: y

Utility Panel See Figure 3-15

Regulator/Audio II PCB Assy. See Figures 3-21 & 3-22 ( ZZ 03585" S Power Supply Assy. ire S See Figure 3-24 (A039246-01 (Power harn. assy.) A037470-01 A037453-03 (On/off switch assy.) (Power cord) 009992-01 A037454-03 (On/off switch cover) (Power cord)

Figure 3-2 Cabinet-Mounted Assemblies U.S.-Built Sit-Down Cabinet A039100-01 F lreland-Built Sit-Down Cabinet A039100-02 F

3-4

Page 30

é Pole Position

a ‘Steering-Wheel Control Assy. See Figure 3-5

Control Panel Assy. See Figures 3-3 & 3-4

aD Coin Door Assy. See Figures 3-16 & 3-17

038870-01 (Coin box exclosure) Maintenance, Repair, and Parts

Manuals, Schematics, & Self-Test Label— See parts list on next page

039155-01 —_——— (Metal attraction panel) Gear-Shifter Control Assy. See Figure 3-8

Video Display See Figure 3-14 037086-01 (Front window retainer)

039141-01 (Front window)

039148-01 (Display shield/graphics)

Foot-Pedal Assy. > See Figure 3-9

(Caster)

Figure 3-2 Cabinet-Mounted Assemblies, continued U.S.-Built Sit-Down Cabinet A039100-01 F Ireland-Built Sit.Down Cabinet A039100-02 F

Page 31

Maintenance, Repair, and Parts Pole Position Cabinet-Mounted Assemblies Sit-Down Cabinet Parts List Assemblies and components in the following parts list are shown in Figure 3-2. Part No. Description \ For U.S.-Built Cabinet A037453-03 Strain-Relief Power Cord (U.S. and Canada) A037701-01 Electromagnetic Interference (EMI) Cage (includes guides) A039101-01 Cabinet Assembly (includes glides and PCB retainers, but not the rear access panel) A039465-01 Main Harness Assembly For Ireland-Built Cabinet A037454-03 Strain-Relief Power Cord (Austria, Belgium, Chile, Denmark, Finland, France, Germany, Greece, Indonesia, Italy, Netherlands, Norway, Spain, Sweden, and Uruguay) A039101-02 Cabinet Assembly (includes glides and PCB retainers, but not the rear access panel) A039101-03 Cabinet Assembly (includes glides and PCB retainers, but not the rear access panel) A039245-01 Main Harness Assembly (for NAMCO PCBs) For U.S.-Built and Ireland-Built Cabinets A039246-01 Power Harness Assembly A039465-02 Main Harness Assembly (for Atari® PCBs) A037470-01 Power On/Off Switch/Mounting Plate Assembly A038881-01 Lock Assembly (for rear access panel) Acceptable substitute is part no. A038881-03 107001-001 Flat Black Paint The following nine items are technical information supplements to this game: C0-218-01 Pole Position Supplement (for NAMCO game PCB removal) SP-218 Pole Position Schematic Package (for Atari® game PCBs) or SP-219 Pole Position Schematic Package (for NAMCO game PCBs) ST-218-01 Pole Position Label with Self-Test Procedure and Option Switch Settings (for Atari® PCBs) or ST-219-01 Pole Position Label with Self-Test Procedure and Option Switch Setting (for NAMCO PCBs) TM-160. Service Manual for 19-Inch Electrohome Color Raster-Scan Display (use with part no. 92-049) TM-201 Service Manual for 19-Inch Wells-Gardner Color Raster-Scan Display (use with part no. 92-055) TM-218 Pole Position Operation, Maintenance, and Service Manual TM-220 Service Manual for 19-Inch Matsushita Color Raster-Scan Display (use with part no. 139003-1004) 72-1620S #6-32 x 1.25-Inch Pan Head Machine Screw 72-5524 #%-20 x 1.50-Inch Hex Head Machine Screw 75-016S #6 Flat Washer 75-045S Ya-Inch Split-Lock Washer 78-3201 Adjustable Glide 78-6900402 Vinyl Foam Single-Coated Adhesive Tape, ¥%-Inch Wide x %Inch Thick (48 inches required; used on control panel) 78-6900804 Vinyl Foam Single-Coated Adhesive Tape, ¥2-Inch Wide x ¥-Inch Thick (48 inches required; used in top slot of video display cleat, and on top and bottom of front window) 002728-01 Control-Panel Mounting Bracket 009992-01 On/Off Switch Cover 035851-01 Top Panel Hinge 037086-01 Front Window Retainer 037742-01 Printed Circuit Board Mounting Bracket 037990-01 Ventilation Grill (on rear access panel) 038091-01 Molded Coin Box (not shown) 038641-01 Ventilation Grille (on rear access panel) 038870-01 Metal Coin Box Enclosure Acceptable substitute is part no. 038781-01 039141-01 Front Window 039144-01 Speaker Grille (located behind seat) 039145-01 Speaker Grille (located under contro! panel) 039148-01 Video Display Shield with Graphics 039155-01 Metal Attraction Panel with Graphics 148001-001 6- x 9-Inch Oval, 4-Ohm, 15 W Unshielded High-Fidelity Speaker (not shown—located behind seat) 148001-013 6- x 9-Inch Oval, 4-Ohm, 15 W Shielded High-Fidelity Speaker (located under control panel) 171034-xxx. Over/Under Coin Door Assembly Acceptable substitute is part no. 171027-001 176015-110 #10 x %-Inch Cross-Recessed, Pan-Head Tapping Screw (not shown—for mounting speakers/grilles to seat back) 178034-024 %-Inch Black Plastic T-Molding & 178034-034 1-Inch Black Plastic T-Molding (located on seat back) 178023-001 4-Inch Rigid Caster 3-6

Page 32

Pole Position

B. Player Controls

WARNING Before you remove or repair any control on the control panel, turn the game off.
CAUTION Before removing the final wing nut on the Sit- Down cabinet, hold the gear-shifter housing with one hand to prevent the front-heavy control panel from falling forward. Maintenance, Repair, and Parts

Opening the Control Panel:

1. Unlock and open the rear access panel (see Figure 3-3), Reach through the opening to the top of the control panel. Remove the four wing nuts and washers that secure the control panel to the Upright cabinet. Two wing nuts and washers secure the control panel to the Sit- Down cabinet.

Guide or pull the control panel forward to its resting Position. The steering wheel and gear shifter are now accessible for maintenance or repair (see Figure 3-4). Make sure the foam tape is in good condition. This tape is on the control panel of the Upright cabinet, and on the display shield for the Sit-Down cabinet. Reassemble in reverse order.

Figure 3-3 Control Panel

Page 33

Maintenance, Repair, and Parts Pole Position

72-JB3814S, a “Gcrew) A Players may receive an electrical shock if this ; control panel is not properly grounded! After ’ servicing any parts on the panel, make sure that the ground wire is firmly attached to the metal tab on the inside of the control panel. 175002. 004. \ (Washer) J

‘A000608-09 Gear-Shifter Control Assy. See Figure 3-6

75-9458 (Hex locknut).

(Spacer)

i A039411-01 (Control panel/decal) 03937301 (Control pane!) 039409-04 (Decal) A039108-01 | 2] (Control panet/decal) 03914301 (Control panel) 039153-04 039132-01 (Decal) : (Spacer) (Washer)

005255-04 (Bezel)

75-5512B (Carriage bolt) ~ 75-5524B (Carriage bolt) Nera ‘Steering-Wheel Control Assy. Assemblies A039107-01 and See Figure 35 03941201 are used with Atari game PCBs; Assemblies A039107-02 and A039412-02 are tused with Namco game PCBs. Figure 3-4 Control Pane! Assembly Upright Cabinet A039412-01 &-02 A " Sit-Down Cabinet A039107-01 &-02 B

Page 34

Pole Position Maintenance, Repair, and Parts

Control Panel Assembly Parts List

Assemblies and components in the following parts list are shown in Figure 3-4.

Part No. Description Upright Cabinet A039411-01 Control Panel with Decal (consists of contro! pane! 039373-01 and decal 039409-04) 177012-111 %-Inch Push-On Spring Nut (not shown) 78-6900402 Vinyl Foam Single-Coated Adhesive Tape, ‘4-Inch Wide x %-Inch Thick (96 inches required) Sit-Down Cabinet

A039108-01 Control Panel with Decal (consists of contro! panel 039143-01 and decal 039153-04) 039132-01 Control Panel Spacer 75-035S Ya-Inch Wide Flat Washer 75-5524B #%-20 x 1.50-Inch Black Carriage Bolt

Upright and Sit-Down Cabinets A039229-01 Steering-Whee! Control Assembly (Namco games use part no. A039229-02) A000608-09 Gear-Shifter Control Assembly 72-JB3814S, #8-16 x .87-Inch Screw 75-5512B #%-20 x .75-Inch Black Carriage Bolt 75-9458 #%-20 Hex Locknut 005255-04 Shifter Bezel 039154-01 Shifter Spacer 175002-004 #10 Flat Washer

Page 35

Maintenance, Repalr, and Parts Pole Position

a - - 178099-003 (Steering whee!) 039243-01 (Label)

039230-01 (Steering cap) —

039231-01 (Shaft)

175003-002 (Nylon washer) 178012-002 039234-01 (Retaining ring) —_ frame) 72:HB3606S : (Hex screw) eA,

asi “a 178100-001 (Flange bearing) (Coupler PCB assy.) 178097-001 (Bearing assy.) 175002-001 (Washer) 175003-002 (Nylon washer) 178012-001 039233-01 (Retaining ring) (Encoder shaft)», 178101-001 178101-002 (Gear) (Gear)

7507014 (Washer) i = NYOGEL 779 (Split-lock washer) 72-8408 —— = SIN-ONE OIL See text for lubrication information.

Figure 3-5 Steering-Wheel Control Assembly A039229-01 D

3-10

Page 36

Pole Position Maintenance, Repair, and Parts

Steering-Wheel Control Assembly Parts List

Assemblies and components listed in the following parts list are shown in Figure 3-5.

Part No. Description A035220-02 Coupler Printed-Circuit Board Assembly (includes Radial Optical Coupler) 72-8008 #10-32 x 0.50-Inch Steel Socket-Head Cap Screw 72-8012 #10-32 x 0.75-Inch Steel Socket-Head Cap Screw 72-8408 #4-40 x 0.50-Inch Steel Socket-Head Cap Screw 72-HB3606S, #6-32 x 0.38-Inch Zinc-Plated Steel Hex Washer-Head Screw 75-040 #10 Split-Lock Washer 75-044 #4 Split-Lock Washer 7507014 #4 Flat Washer 79-58356, 4-Position Connector with Locking Ramp (located on the Coupler PCB Assembly) 030369-01 Radial Optical Coupler (located on the Coupler PCB Assembly) 035221-01 100 2, +5%, %4W Resistor (located on the Coupler PCB Assembly) 039230-01 Steering Cap 039231-01 Steering Shaft 039232-01 Spacer 039233-01 Encoder Shaft 039234-01 Steering Frame 039243-01 Steering Cap Label 035938-01 Encoding Wheel 107013-001 3-in-One® Oil 175002-001 Flat Washer 175002-002 #10 Heavy Flat Washer 175003-002 Nylon Flat Washer 178012-001 Retaining Ring for 0.75-Inch Shaft 178012-002 Retaining Ring for 0.25-Inch Shaft 178027-001 Nyogel 779 Lubricant 178097-001 Bearing for 0.25-Inch Shaft 178099-003 Steering Wheel 178100-001 Bearing Flange for 0.75-Inch Shaft 178101-001 24 Diametral Pitch x 20° Pressure Angle x 2.500 Pitch Diameter Spur Gear 178101-002 24 Diametral Pitch x 20° Pressure Angle x 0.583 Pitch Diameter Spur Gear

Page 37

Maintenance, Repair, and Parts

WARNING

Before you remove or repair any player control, tur the game off.

Removing the Coupler PCB, Encoding Wheel, and Steering Wheel:

  • Open the contro! panel (see Figure 3-3). To remove the steering-wheel control assembly, disconnect the green ground wire from the grounding hardware. Remove the hardware which secures the steering-wheel control assembly to the control panel (see Figure 3-4). Pole Position

Unplug the harness connector on the Coupler PCB. To remove the Coupler PCB, remove the hardware securing the PCB to the steering frame. To remove the encoding-wheel assembly, hold the shaft of the encoding wheel in a fixed position with a wrench. Use an Allen wrench to remove the cap screw, encoding wheel, washers, spacer, and bearing. To remove the encoder shaft, pry off the retaining ring. To remove the steering wheel, hold the steering wheel shaft in a fixed position. Remove the cap screw, washers, and gear. Pry off the retaining ring and remove the heavy washer. Reassemble in reverse order.

OPEN-END WRENCH ALLEN WRENCH.

ENCODING WHEEL

Figure 3-6 Steering-Wheel Control Screw Adjustment

3-12

Page 38

Pole Position

Lubricating the Steering-Wheel Control:

Periodic maintenance of the steering-wheel contro! assembly must include the following procedures:

  • Check that the #4-40 x 12-inch socket-head cap screw (part no. 72-8408) on the encoder shaft is secure (see Figure 3-6). \f the screw needs tightening, hold the encoder shaft (part no. 039233-01) with a 7,-inch openend wrench while tightening the screw with a %,-inch Allen wrench.
  • Check that the #10-32 x ¥2-inch socket-head cap screw (part no. 72-8008) on the steering-wheel shaft is tight (see Figure 3-5). If the screw needs tightening, hold the steering wheel still while using a %-inch Allen wrench to tighten the screw.
  • Check, and if necessary, lubricate the encoder shaft (part no. 039233-01) and the two flat nylon washers (part no. 175003-002) as shown in Figure 3-5. Use ONLY the recommended lubricant, Nyogel 779 (part no. 178027-001). Nyoge! 779 is a damping grease and will aid in the smooth operation of the control. Make sure a HEAVY film of this lubricant is applied to the encoder shaft and both surfaces of the nylon washers.
  • Check for a grinding feeling caused by inadequate lubrication or by the gears being too close together. To correct this condition, lubricate with Nyogel 779, and/or loosen the locknut on the bearing assembly Maintenance, Repair, and Parts

(part no. 178097-001) and move the bearing away from the main steering shaft toward the coupler PCB assembly. This movement may be very smail, but it can make a difference.

Check, and if necessary, lubricate the bronze flange bearings (part no. 178100-001) in the steering frame (part no. 039234-01), using a few drops of a light machine oil, such as 3-in-One oil (part no. 107013-001) (see Figure 3-5). The steering-wheel control assembly should be positioned as follows (see Figure 3-7): a. Open the control panel. b. Disconnect the green ground wire from the grounding hardware. Remove the four carriage bolts that secure the steering-wheel control assembly to the control panel. c. Rotate the steering-wheel control assembly 90° so that the encoding wheel assembly and the encoder shaft are on the bottom (nearest the floor). All new Pole Position games will be assembled in this manner. d. Reinsert the four carriage bolts that secure the steering-wheel control assembly to the control panel. Reconnect the green ground wire.

STEERING-WHEEL CONTROL oo COUPLER PCB

GEAR-SHIFTER CONTROL

CONTROL PANEL

Figure 3-7 Steering-Wheel Control Orientation

3-13

Page 39

Maintenance, Repair, and Parts

0n5265.04 OD (Bezel) \

NOTE The shift bezel is not part of the gear shifter assembly and must be purchased separately.

ye See text for lubrication information.

000610-02 (Shifter handle)

039705-01 (Spring)

76-11375S er eK ey ®

(Shift detent)

(Actuator pin)

Figure 3-8 Gear-Shifter Control Assembly A000608-09 AB d 75-944S TN (Hex nut) 035301-02 Pole Position

000609-02 (Shift housing)

72-1412S (Screw) 65-0210 (Switch)

Page 40

Pole Position

WARNING

Before you remove or repair any player control, tum the game off.

Removing the Gear-Shifter Control Assembly:

  • Open the control panel (see Figure 3-3).
  • To remove the gear-shifter control assembly (see Figure 3-4), disconnect the plug-in connectors from the switch. Remove the hardware that secures the gear-shifter control assembly to the control panel.
  • To open the gear-shifter assembly, remove the six screws that secure the two halves of the housing (see Figure 3-8). Maintenance, Repair, and Parts
  • To remove the switch, remove the two screws and locknuts that secure the switch to the housing. Be careful not to lose the small actuator pin that sits above the switch actuator.
  • Reassemble in reverse order.

Lubricating the Gear-Shifter Control: To lubricate the gear-shifter control assembly, open the control panel (see Figure 3-3) and remove the gear-shifter control assembly using the procedure above. Apply a lightduty lubricant (such as Nyogel 779) every six months to the spherical part of the handle and the detent.

Gear-Shifter Control Assembly Parts List

Assemblies and components listed in the following parts list are shown in Figure 3-8.

Part No. Description

000610-02 Gear-Shifter Handle 65-021A Single-Pole Single-Throw Low-Force Miniature Switch 72-JB3606 #6 x 0.38-Inch Steel Plastite Screw Acceptable substitutes are part nos. 72-JB3608, 72-JA4608, and 72-JB16068 72-1412S #4-40 x 0.75-Inch Cross-Recessed Pan-Head Steel Machine Screw

76-11375S, %-Inch Ball Bearing 75-944S #4-40 Self-Locking Polymer Hex Nut 78-3002003 Spring 000609-02 Gear-Shifter Housing (two required) 005255-04 Shifter Bezel 035792-01 Shift Detent 035301-02 Actuator Pin 178027-001 Nyogel 779 Lubricant (not shown)

3-15

Page 41

Maintenance, Repair, and Parts Pole Position

On 039241-01 Gatety tread) See text for lubrication information.

039240-01 (Foot pedal—accelerator) 039236-01 (Pivot pin) ee m, F Pr : 040028-01

(Compression spring)

039242-01 178012-004, \ (Cable) (Retaining ring)

039238-01 (Pulley)

039704-01 « : * 72-8606 (Extension spring) (Cap screw)

ft Cap screw of pulley must be in this position when pedal is fully open (at rest). 039703-01 (Cable spring) 039239-01 (Base plate)

72-HB3410S* (Screw) 19-9026 (Potentiometer) 160023-001* (Switch)

*For Sit-Down cabinet (dual foot-pedal assembly)

**For Upright cabinet (single foot-pedal assembly)

03914201" (Mounting plate)

039379-01** (Mounting plate)

4 = NYOGEL 779 75-040S** ——_—____+@3 (Washer) G3 = WD-40

Figure 3-9 Foot-Pedal Control Assembly 75-9418 (Hex locknut)

3-16

Page 42

Pole Position Maintenance, Repair, and Parts

Foot-Pedal Control Assembly Upright A039413-01 B Sit-Down A039109-01 C Parts List

Assemblies and components in the following parts list are shown in Figure 3-9.

Part No. Description Sit Down Cabinet A039247-01 Dual Foot-Pedal Control Harness Assembly 72-HB3410S #4-40 x .62-Inch Thread-Forming Hex Washer-Head Screw 75-010S #10 Tooth Internal Lock Washer 160023-001 SPDT Snap Switch with Actuator Upright Cabinet A039463-01 Single Foot-Pedal Control Pedal Harness Assembly 75-035S Ya-Inch Flat Washer 75-040S #10 Tooth Internal Lock Washer 75-5520B #%-20 x 1.25-Inch Black Carriage Bolt (not shown) 75-915S #'%4-20 Hex Nut 039379-01 Single Foot-Pedal Control Mounting Plate Upright and Sit-Down Cabinets 19-9026 5 kQ Potentiometer 72-8606 #6-32 x .38-Inch Hex Socket-Head Cap Screw 75-9415 #10-24 Hex Locknut

040028-01Compression Spring(for pedal)

039236-01 Pivot Pin 039238-01 Pulley 039239-01 Foot-Pedal Control Base Plate 039240-01 Foot Pedal 039241-01 Safety Tread 039242-01 Cable 107012-001 Dry Teflon Spray Lubricant (not shown) 178012-004 External Retaining Ring for %-Inch Diameter Shaft

178026-005Extension Spring(for cable)
178026-006Extension Spring(for pedal)

3-17

Page 43

Maintenance, Repair, and Parts

WARNING

Before you remove or repair any player control, turn the game off.

Removing the Foot-Pedal Control Assembly:

  • Unlock and open the rear access panel. Reach through the opening to the top of the foot-pedal control.
  • Remove the two locknuts located on the top two footpedal mounting screws.
  • From the front of the Upright cabinet or in the player area of the Sit-Down cabinet, remove the foot-pedal mounting screws and lift out the foot-pedal control assembly. Pole Position

Foot-Pedal Control Maintenance:

NOTE If the game fails to reach maximum speed, refer to Table 16 to make sure the option switch settings are set according to manufacturer’s recommendations. If the switch settings are correct, perform the maintenance procedures set out below. .

Periodic maintenance of the foot-pedal controls must include the following procedures:

  • The only maintenance required on this newly designed foot-pedal control is lubrication every four months (see Figure 3-9). Lubricate the pivot pin and surround-
  • Place the foot-pedal control assembly upside down on a work surface in front of you with the pedal in a fully open position and the hinged end away from you.

CABLE

  • Wrap the cable one quarter-turn around the pulley and bring it out through the notch toward the cap screw.
  • Thread the cable up through the opening in the base plate.

LARGER EYELET

  • Rotate the pulley until the cap screw points straight up.

PULLEY

  • Hook the larger eyelet of the cable to the foot-pedal bracket.

BRACKET

Figure 3-10 Foot-Pedal Pulley Cable Rewinding

3-18 \

Page 44

Pole Position Maintenance, Repair, and Parts

ing area, the spring cable, and pulley with dry teflon 3. If the pulley cable needs rewinding, adjust as shown in

spray. If needed, apply a light-duty lubricant like WD-40 Figure pen! 9, ac

to the potentiometer shaft only.

  • If your accelerator pedal fails to return to its uppermost position, check for the following conditions: NOTE a. Inadequate lubrication of the pedal assembly. Lubricate as necessary. If it is necessary to disassemble the foot-pedal control assembly and remove the pulley cable
b.A broken extension spring (part no, 03970401).(part no. 039242-01), MAKE SURE the cable is

Replace if necessary. wound as illustrated in Figure 3-10. BE

c.Abroken or inadequately lubricated compressionCAREFUL not to cut or fray the cable in the

spring (part no. 000592-01). Replace and/or lubri- disassembly/assembly process. Note that the cate if necessary. foot-pedal assembly must be removed from the game cabinet in order to wrap the cable cor-

d.Inadequate lubrication of the potentiometer shaftrectly,

(part no. 19-9026). Lubricate as necessary with a light-duty lubricant, such as WD-40 (part no. 78-1701).

  • Wrap the cable twice around the cap screw in a clockwise direction.
  • Attach the smaller eyelet on the cable to the cable spring. NOTE: You \ § may find it helpful to compress the

Ne base plate slightly and extend the

=<] cable spring during this step.

  • Bring the cable back through the notch and wrap it around the pulley one and one-half times.

CABLE SPRING

SMALLER EYELET

Figure 3-10 Foot-Pedal Pulley Cable Rewinding, continued

3-19

Page 45

Maintenance, Repair, and Parts

C. Fluorescent Tube and Speaker Replacement

WARNING Before you remove or repair the fluorescent tube or speaker, turn the game off. If you drop a fluorescent tube and it breaks, /t will implode! Shattered glass can fly six feet or more from the implosion. Use care when replacing any fluorescent tube.

Upright Cabinet

Removing the Tube and Speaker Board:

1. From the back of the game, unlock and open the rear access panel. Unplug the tube and speaker’s 5-pin harness connector (see Figure 3-11). From the front of the game, remove the three buttonhead screws and lock washers that secure the upper attraction-panel retainer to the cabinet. Loosen the screws and washers that secure the lower attractionpanel retainer to the cabinet. Remove the attraction glass. Remove the lower retainer. Pole Position

  • Remove the two wood screws that secure the tube and speaker board to the cabinet. Slide this board out of the cabinet. After making necessary repairs or replacements, make sure that the tube and speaker board is pushed all the way back on the tube and speaker panel when you reinstall the board.

Replacing the Fluorescent Tube:

  • Check that the green ground wire is securely attached to the large metal bracket and the ballast transformer on the wood panel. If the tube is not grounded, it may not start.
  • Remove the cardboard locking tab at each end of the tube (see Figure 3-12). Slightly rotate the tube up or down and carefully remove it from the tube holder.
  • Replace it with a new tube. Do not snap in the tube vigorously— you may break it, causing an implosion! Replace the locking tabs.

Replacing the Upper Speaker:

  • Disconnect the two plug-in connectors on the speaker.
Note that the white wire (+) connects on the side marked with a painted dot.
  • Remove the screws that attach the speaker to the board (see Figure 3-12). Replace with a new speaker and reinstall the tube and speaker board.

Replacing the Lower Speaker: From the back of the game, unlock and open the rear access panel. Refer to upper speaker removal procedure in Figure 3-12).

3-20 (Tape) oseqt601—_____ sf {Attraction glass/ graphics)

78-6900402 (Tape)

148001-001 039144-01 (Speaker) (Speaker grille) § 003053-01 (Retainer)

Figure 3-11 Fluorescent Tube and Speaker Board Removal

Page 46

Pole Position Maintenance, Repair, and Parts

148001-013 70-304 99-11006 (Speaker) (Tube) (Tab)

179035-001 | (Tube holder) ! A037457-01 i Oe” —v (Harness)

| 142028-001 (Transformer) 142028-002 (Transformer)

(Starter) 99-11009 (Socket) racket)

NOTE To make sure that the fluorescent tube starts, check that the ground wire is firmly attached 79-561816P 7 1 to both the ballast transformer and the steel (Wire nut) von ‘a tube bracket. @ A037540-01 (Ground wire)

Figure 3-12 Fluorescent Tube and Speaker Board Assembly U.S.-Built Upright Cabinet A039415-01 A Ireland-Built Upright Cabinet A039415-02 A Parts List

Part No. Description For U.S-Built Upright Cabinet 142028-001 60 Hz, 118 V, Ballast Transformer (used on A037458-01 assembly) For Ireland-Built Upright Cabinet 142028-002 50 Hz, 118 V, Ballast Transformer (used on A037458-02 assembly) For U.S- and Ireland-Built Upright Cabinet A037457-01 Tube and Speaker Harness Assembly A037540-01 Ground Wire with Ring Lug 70-304 18-Inch, 15 W, Cool White Fluorescent Tube 78-6900402 Vinyl Foam Single-Coated Adhesive Tape, ¥%-Inch Wide x ¥Inch Thick 79-561816P Spring-Connector Wire Nut for 16- to 18-Gauge Wires 99-11003 Fluorescent Tube Starter 99-11006 Fluorescent Tube Locking Tab (tab consists of two pieces) 99-11009 Starter Socket 003053-01 Upper and Lower Attraction Glass Retainer 037469-01 Steel Tube Bracket 039366-01 Tube and Speaker Board 039418-01 Attraction Glass with Graphics 148001-013* 6 x 9-Inch Oval, 4-Ohm, 6-Ounce, Shielded High-Fidelity Speaker 176015-110 #10 x 5/8-Inch Pan Screw 179035-001 2-Pin Fluorescent Tube Holder *148001-001 6 x 9-Inch Oval, 4-Ohm, 6-Ounce, High-Fidelity Speaker—mounted to the cabinet near the coin door, behind speaker grille part no. 039144-01

3-21

Page 47

Maintenance, Repair, and Parts

Sit-Down Cabinet

Replacing the Front Speakers:

  • For the right speaker, unlock and open the rear access panel (see Figure 3-13). For the left speaker, open the control panel (see Figure 3-3). Unplug the two plug-in connectors. Remove the two screws that secure the speaker to the wood speaker panel. en Replacing the Seat-Panel Speakers:

4.

5. Pole Position

aD Remove the six wood screws that secure the seatback panel to the cabinet (see Figure 3-13). Lean the seat-back panel forward. Disconnect the two plug-in connectors on each speaker. Remove the seat-back panel from the player area of the cabinet. Remove the four screws that secure each speaker to the seat-back panel. Reassemble in reverse order.

Figure 3-13 Sit-Down Cabinet Speaker Removal

3-22

Page 48

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 49

Maintenance, Repair, and Parts.

D. Video Display

WARNING SHOCK HAZARD The following procedure should only be performed by a qualified service technician. Before removing or repairing the video display, turn the game off. High voltages may exist in any video display, even with power disconnected. Use extreme
caution and do not touch electrical parts of the display yoke area with your hands or with metal objects in your hands! Discharge the high voltage from the cathode ray tube as follows: First, attach one end of a large, well-insulated, 20-kV jumper to ground. Momentarily touch the free end of the grounded jumper to the anode by sliding it under the anode cap. Then, wait two minutes and discharge the anode again. IMPLOSION HAZARD If you drop the display and the picture tube breaks, it will implode! Shattered glass and the yoke can fly six feet or more from the implosion. Use care when replacing any display.

Removing the Video Display From the Upright Cabinet:

  • From the back of the cabinet, unlock and open the rear access panel. Unplug the 6-pin connector from the video chassis, the 2-pin 110-VAC connector, and disconnect the ground wire (see Figure 3-14).
  • Remove the four sets of hardware that secure the video display to the wood display shelf. Open the control panel (see Figure 3-3). Remove the three wing nuts (located on the displayshield support) that secure the dashboard panel to the cabinet.
  • From the front of the cabinet, lift off the dashboard panel.
  • Remove the hardware that secures the display-shield retainer. Lift the display shield up and out of the cabinet.
  • Remove any staples that may secure the bezel to the cabinet. Then, carefully remove the cardboard bezel.
  • Carefully pull the display out through the front of the cabinet. Place the display in a protected location. After servicing the display, reinstall in reverse order.

3-24 Pole Position

Removing the Video Display From the Sit-Down Cabinet:

  • From the back of the cabinet, unlock and open the rear access panel. Unplug the 6-pin connector from the video chassis, the 2-pin 110-VAC connector, and disconnect the ground wire (see Figure 3-14).
  • Remove the four sets of hardware that secure the video display to the wood display shelf.
  • Open the control panel (see Figure 3-3).
  • Move to the player area of the cabinet. Grasp the bottom edge of the video display shield and slide the shield out and down. Make sure the foam tape on the bottom of the shield is in good condition.
  • Remove any staples that may secure the bezel to the cabinet. Then, carefully grasp the bottom edge of the cardboard bezel and remove it from the cabinet.
  • Pull the display out through the front of the cabinet. Place the display in a protected location. After servicing the display, reinstall in reverse order.
Page 50

Pole Position Maintenance, Repair, and Parts

039148-01 H Shield) 039149-01 039371-01 i (Bezel) (Retainer) 039417-01 (Shiela) 039407-01 | / (Bezel) [ 92-049 (Electrohome display) & or 139003-1004 (Matsushita display)

i 78-6900402 (Shell) a ] (Tape) 039123-02 es 78-6900804 (Shelf Ss (Tape) aay

Figure 3-14 Video Display Upright and Sit-Down Cabinets Parts List

Part No. Description For Upright Cabinet 039363-02 Display Shelf 039371-01 Retainer 039407-01 Display Bezel 039417-01 Display Shield 78-6900402 Vinyl Foam Single-Coated Adhesive Tape, %4-Inch Wide x }-Inch Thick For Sit-Down Cabinet 039123-02 Display Shelf 039148-01 Display Shield 039149-01 Display Bezel 78-6900804 Vinyl Foam Single-Coated Adhesive Tape, ¥2-Inch Wide x Inch Thick For Upright and Sit-Down Cabinets 92-049 19-Inch Electrohome Color Raster-Scan Display Alternate display is part no. 139003-1004— 19-inch Matsushita Color Raster-Scan Display

3-25

Page 51

Maintenance, Repair, and Parts Pole Position

ete The utility panel is located inside the upper coin door.

E. Utility Panel This panel includes the volume control(s), self-test switch,

auxiliary coin switch, and the coin counter(s) (see Figure 3-15). The auxiliary coin switch is used to credit the game without tripping the coin counter. Before removing or repairing the utility panel, turn the game off. Players may receive an electrical shock if the NOTE

Only Ireland-Built cabinets have two coin counters. If using both coin counters, the pad at 10D (pins 11 and 12) on the CPU PCB must be split. utility panel is not properly grounded! After servicing any parts on the panel, make sure that the ground wire is firmly attached to the metal screw on the back of the coin counter.

A039254-01 (Dual component harness) (Utility panel— 5 A038004-0' U.S.-Buill Upright only) \<— (utility panel 039295-01 harness) (Utility panel)

(Coin counter) a1 178070001 (Vol. control harness) (Vol. control knob)

176018-002 (Screw) 75.9168 SELF-TEST SWITCH = (Hex nut) ——_-75-9910W0

(sno (Stamped nut) (Auxiliary

coin switch)

SWITCH NOT USED

Figure 3-15 Utility Panel Assembly A039391-xx F

3-26

Page 52

Pole Position Maintenance, Repair, and Parts

Utility Panel Assembly Parts List

Part No. Description For U.S.-Built Upright Cabinet 039457-01 Utility Panel (for 2 volume controls) For Ireland-Built Upright Cabinet 039295-01 Utility Panel (for 4 volume controls) For U.S.- and Ireland-Built Upright Cabinet A039254-01 Dual Component Harness Assembly For U.S.- and Ireland-Built Sit-Down Cabinet A038004-01 Utility Panel Harness Assembly A039248-01 Volume Control Harness Assembly 039295-01 Utility Panel (for 4 volume controls) For U.S.- and Ireland-Built Upright and Sit-Down Cabinets A002465-01 6 V Coin Counter 19-9032 50 Q, 12.5 W Volume Control 62-041 SPST Momentary-Contact Pushbutton Auxiliary Coin Switch with Black Cap 69-001 DPDT Self-Test Switch 176018-002 #6-32 x Y2-Inch Thread-Forming Screw 75-916S #6-32 Steel Machine Hex Nut 75-9910W0 #15/32-32 Stamped Nut 178070-001 Volume Control Knob

3-27

Page 53

Maintenance, Repair, and Parts Pole Position

F. Coin Doors

470000-001 (Lamp) 2 179047-001 NN “99-5023 (Lamp Base) Vig > (Base Plate)

99.15056 “ 5028 15040

(Screw tor Bezel) bet enn

9915025, oe j (Coin inlet) oa

a _- 99-18054 (Pivot for Lever)

75-9148 Hex Nut) (Hex Nut) 7

(Lock Wash.)

99-15029 (Bracket) *\ ¢— 99-15060 (Sw. Cover)

99-15042 (Switch)

721414 (Screw)

Figure 3-16 Vertically Mounted Coin Door 171034-xxx

3-28

Page 54

Pole Position Maintenance, Repair, and Parts

’ 99-15038 A037542.01 P ; (Bezel for Button) (Harness—not shown) SS 5

(eter bot i C a ‘ : 99-15001 thru 99-15011 per Doo ~ (Return Button)

99-15063 S (Screw) 99-15052 i" _ pring for Button)

99-15071 (Clamp)

99-15039 (Bezel for Cover)

99-15036 (Cover) 99-15067 (Lock Assy.)

038091-01 (Coin Box) 99-15066 (Screw)

99-15074 (Lower Door)

(Doors and Frame) 99-15072 (Door Frame)

171034-001 — U.S. 25¢/25¢ Coin Door 171034-006 — U.K. 20 P/50 P Coin Door 171034-011 — German 1 M/S M Coin Door 171034-003 — Canadian 25¢/25¢ Coin Door 171034-009 — German 2 M/1 M Coin Door 171034-015 — French 2 Fi1 F Coin Door 171034-005 — U.K. 10 P/50 P Coin Door 171034-010 — German 2 M/5 M Coin Door

Figure 3-16 Vertically Mounted Coin Door, continued 171034-xxx

3-29

Page 55

Maintenance, Repair, and Parts Pole Position

Vertically Mounted Coin Door Parts List

Part No. Description A037542-01 Harness Assembly 72-1414S #4-40 x %-Inch Cross-Recessed Pan-Head Steel Machine Screw 75-056 #6 Internal-Tooth Zinc-Plated Stee! Lock Washer 75-9148 #4-40 Steel Machine Hex Nut 75-3414S, #4-40 x %-Inch 82° Cross-Recessed Flat-Head Steel Machine Screw 99-15001 Coin Return Button with U.S. 25¢ Price Plate 99-15002 Coin Return Button with U.S. $1 Price Plate 99-15003 Coin Return Button with German 1 DM Price Plate 99-15004 Coin Return Button with German 2 DM Price Plate 99-15005, Coin Return Button with German 5 DM Price Plate 99-15006 Coin Return Button with Belgian 5 Fr Price Plate 99-15007 Coin Return Button with French 1 Fr Price Plate 99-15008 Coin Return Button with Japanese 100 Yen Price Plate 99-15009 Coin Return Button with British 10 Pence Price Plate 99-15010 Coin Return Button with Australian 20¢ Price Plate 99-15011 Coin Return Button with Italian 100 Lire Price Plate 99-15023 Base Plate 99-15025 Left Half of Coin Inlet 99-15026 Right Half of Coin Inlet 99-15027 Side Plate of Coin Return Box 99-15028 Base Plate of Coin Return Box 99-15029 Switch Bracket 99-15036 Metal Coin Return Cover 99-15038 Bezel for Coin Return Button 99-15039 Metal Bezel for Coin Return Cover 99-15040 Coin Return Lever 99-15042 Coin Switch for U.S. 25¢ 99-15052 Spring for Coin Return Button 99-15054 Pivot for Coin Return Lever 99-15055, Retaining Screw 99-15056 #4-40 x ¥,Inch Cross-Recessed Pan-Head Steel Machine Screw 99-15060 Switch Cover 99-15063 Screw for Hinge 99-15066 Screw for Clamp 99-15067 Lock Assembly 99-15070 Doors and Frame 99-15071 Clamp for Frame 99-15072 Door Frame 99-15073 Upper Door 99-15074 Lower Door 99-15075 Switch Adjuster 038091-01 Coin Box (Not included in assembly) Acceptable substitute is part number A037491-01 170000-001 6.3 V Miniature Wedge-Base Incandescent Lamp 171006-035 Metal Coin Mechanism 179047-001 Lamp Base

3-30

Page 56

Pole Position Maintenance, Repair, and Parts

99-10140 (Panel assy.)

99-10116 (Lever)

99-10152 (Right coin inlet)

99-10096 (Fastener) 75-9448 (Hex nut)

99-10151

(Lamp socket).

70-11-47 (Lamp)

S / 99-10104

  • (Bar retainer) ore 99-10147 (Screw) 99-10105 (Harness) 99-10154 Z a ( (Bracket af | . ZA i 99-10042 thru 99-10045
,7(Coinswitchassy,
mun4y}(Coin switch assy.)

(Coin return box) a >

a{|.

65-441C oo (Coin switch) ~ aa So DP

Pa‘SA99-10150
~‘<*(Switch cover)
~~Ke La«

99-1075 thru 99-10078 _~ 2 (Switch wire) 99-1008 75-1412S (Retainer) (Screw)

Figure 3-17 American-Made Coin Door 171027-001 A

3-31

Page 57

a Maintenance, Repair, and Parts

72-HA1404C (Screw)

99-10139 (Coin door) ———>}

99-10145 —>-( aS (Cam) \ @®

72-JA1405B (Screw)

038091-01 (Coin box)

Figure 3-17 American-Made Coin Door, continued 171027-001 A

3-32 99-10119 (Button assy) ) 9.190148 \3 \\

. 99-10115 Pole Position

99-10142 (Button housing)

99-10134 (Cover)

(Spring)

99-10117 (Coin return door)

99-10144 |~—(Channe! clip)

i)

99-10149 (Service door)

99-10143 (Frame)

Page 58

Pole Position Maintenance, Repair, and Parts

American-Made Coin Door Parts List Assemblies and components in the following parts list are shown in Figure 3-17.

Part No. Description A039576-01 Coin Option Interconnect Assembly (not shown) 171006-035 Metal Coin Mechanism for U.S. $.25 65-4416 Coin Switch 70-11-47 Miniature Bayonet Lamp 72-9406S #4-40 x %-Inch Truss-Head Screw 72-HA1404C #4-40 x Ya-Inch Pan-Head Screw 72-JA1405B #4-40 x .31-Inch Pan-Head Screw 75-1412S #4-40 x 3-Inch Pan-Head Screw 75-9948, #4-40 Lock Nut 99-10008 Retainer 99-10042 Coin Switch Assembly for Belgium 5 Fr and U.S. $.25 99-10043 Coin Switch Assembly for German 1 DM, Japanese 100 Yen, Swiss 1 Fr 99-10044 Coin Switch Assembly for German 2 DM, Italian 100 L, U.S. $1.00 99-10045 Coin Switch Assembly for Australian $.20, German 5 DM, British 10 P 99-10068 Coin Return Chute 99-10075 Switch wire (included in coin switch assembly) 99-10076 Switch wire (included in coin switch assembly) 99-10077 Switch wire (included in coin switch assembly) 99-10078 Switch wire (included in coin switch assembly) 99-10080 Lamp socket 99-10081 Key holder 99-10096 Fastener 99-10104 Bar retainer 99-10105 Bar 99-10115 Spring 99-10116 Plastic Coin Return Lever 99-10117 Steel Coin Return Door 99-10118 Amber Coin Return Button 99-10119 Amber Coin Button for U.S. $.25 99-10134 Coin Button Cover 99-10139 Coin Door 99-10140 Coin Door Inner-Panel Assembly 99-10141 Diecast Coin Return Cover 99-10142 Diecast Button Housing 99-10143 Coin Door Frame 99-10144 Coin Door Channel Clip 99-10145 Offset Cam (includes 99-10148—Lock) 99-10146 Coin Inlet Chute Assembly 99-10147 American-Made Coin Door Harness 99-10149 Service Door 99-10150 Switch Cover 99-10151 Left Coin Inlet 99-10152 Right Coin Inlet 99-10153 Coin Return Box 99-10154 Bracket Assembly

3-33

Page 59

Maintenance, Repair, and Parts Pole Position

G. Printed-Circuit Boards

039378-03 (Retainer) 03776701 (EMI Shield PCB)

476015-110 Shield PCB 03787301 (Screw) (Spacer) «3

A039431-01 (End PCB)

° @ (Screw) A037701-01 (Foam pad) 72-1604F (EMI cage) (Screw)

178044.242 bess A030185-21 (Pole Position Video PCB) (Grommet) (Pole Position CPU PCB) 175009-221 a Washer i ) 178045-442 The FCC requires that the game (Fastener) PCB be housed in the EMI cage with the Shield PCB attached.

03543501 176015-110 A035435-05 (Screw) (Regulator/ 175004-708 Audio || PCB) (Washer)

*Steps 1, 10, and 11 are not illustrated.

Figure 3-18 Removing the Printed-Circuit Boards

Page 60

Pole Position

WARNING

Before you remove or repair any printed-circuit board, turn the game off.

Removing the Printed-Circuit Boards: Removing the Game PCBs from the EMI Cage

  • Open the rear access panel.
  • The game printed-circuit boards (PCBs) are located inside the electromagnetic interference (EMI) cage (see Figure 3-18). The EMI cage is located on the cabinet wall of the Upright game and on the inside of the rear access panel of the Sit-Down game. Unplug the two harness edge-connectors from the EMI Shield PCB.
  • To remove the game PCBs, pull the eight nylon snap-in fasteners on the EMI Shield PCB to the unlocked position. Carefully slide the Shield PCB and attached PCBs straight out of their guides. Be careful not to twist the boards, as this may loosen connections or components. Removing the EMI Shield PCB from the Game PCBs
  • Remove the two pan-head screws that connect the EMI Shield PCB to the spacers.
  • Push the EMI Shield PCB off the game PCBs by applying pressure with your thumbs to the edge connectors. Maintenance, Repair, and Parts
  • Unplug the End PCB that connects the two game PCBs.
  • Determine which PCB you need to repair or replace, and remove the two pan-head screws that connect that PCB to the spacers. Replace or repair as required, and reinstall the PCBs. (Make sure the foam vibration damper is placed between the game PCBs.) Removing a Regulator/Audio Il PCB:
  • To remove a Regulator/Audio Il PCB, disconnect the small harness connectors on the board.
  • Remove the hardware that secures the Regulator/Audio || PCB to the cabinet, and carefully lift the board from the retainer. Do not twist the board, as this may loosen connections or components. Replace or repair as required and reinstall the PCB.
CAUTION

Make sure that the connectors on each PCB are properly plugged in. Note that they are keyed to fit only one way. If they do not slip on easily, do not force them. A reversed connector may damage your game and void the warranty.

  • Close and lock the rear access panel.
  • Important: Perform the self-test.

Printed-Circuit Board Mounting Hardware Parts List

Assemblies and components in the following parts list are shown in Figure 3-18.

Part No. Description

U.S-Built Upright and Sit-Down Cabinets A037701-01 Electromagnetic Interference (EMI) Cage (includes guides) 72-1404F #4-40 x ¥%-Inch Cross-Recessed Steel Screw 72-1604F #6-32 x ¥a-Inch Cross-Recessed Steel Screw 034536-02 Foam Pad 037873-01 Spacer 039378-03 Dual-Slotted Retainer 175004-708 #8 Fiber Washer 175009-221 Plastic Spacer (for EMI shield PCB) 72-6812S #8 x ¥-Inch Steel Machine Screw 178044-242 Grommet 178045-442 Snap-In Fastener

Ireland-Built Upright and Sit-Down Cabinets* 72-6624S, #6 x 1 ¥2-Inch Cross-Recessed Pan-Head Tapping Screw 74-5608NN #6-32 x Ye-Inch Spacer 75-99516 #6-32 Nut/Washer Assembly 034536-02 Foam Pad 039157-02 Dual-Slotted PCB Retainer 175004-706 #6 Fiber Washer 175004-708 #8 Fiber Washer 72-6812S #8 x ¥-Inch Steel Machine Screw 178020-750 Nylon Spacer

*Not shown in illustration

3-35

Page 61

Maintenance, Repair, and Parts Pole Position

3-36 rIoFE Fae a5 i Le] ig cna eaats & i] BB & B Hd $a ES

ee PEE CEP Pe] 1 2) poio] peat

we_6) BA ia
a= [ileHl i) a8 8
a Je ae HybHes fhhy _o
° irFi}___B
in ity Ey aflf:

go fg tee i

ob) la=e aa) |
ia itia il :
. F i SEE IE a ae8} fe] ft#5
=| ° 0 GHes Hitlersi= ‘

sal LR)

Figure 3-19 Central Processing Unit (CPU) Printed-Circuit Board Assembly A039185-21 B

Page 62

Pole Position

Parts List

Assemblies and components in the following parts list are shown in Figure 3-19. Figure 3-16 Central Processing Unit Printed-Circuit Board Assembly Maintenance, Repair, and Parts

DesignatorDescriptionPart No.

Capacitors

C2-C50.01 uF, 100 V Radial-Lead Mylar Capacitor21-101103
cé33 pF, 100 V Radial-Lead Epoxy-Dipped Mica Capacitor128002-330
c70.1 uF, + 10%, 50 V Ceramic-Disc Axial-Lead Capacitor122002-104
co10 uF, 25 V Aluminum Electrolytic Fixed Axial-Lead Capacitor24-250106.
C100.1 uF, + 10%, 50 V Ceramic-Disc Axial-Lead Capacitor122002-104
ci47 uF, 10 V Aluminum Electrolytic Fixed Axial-Lead Capacitor24-100476
C120.1 uF, + 10%, 50 V Ceramic-Disc Axial-Lead Capacitor122002-104
C130.01 uF, +80%, -20%, 25 V Ceramic-Disc Axial-Lead Capacitor122005-103
C14, C150.1 uF, + 10%, 50 V Ceramic-Disc Axial-Lead Capacitor122002-104
C16-C230.01 pF, + 80%, -20%, 25 V Ceramic-Disc Axial-Lead Capacitor122005-103
C24, C250.1 uF, + 10%, 50 V Ceramic-Disc Axial-Lead Capacitor122002-104
C2647 uF, 10 V Aluminum Electrolytic Fixed Axial-Lead Capacitor24-100476
C27, C280.0022 uF, + 10%, 100 V Radial-Lead Plastic Film Capacitor121022-222
C29, C300.022 uF, 100 V Radial-Lead Mylar Capacitor21-101223
C31, C320.01 uF, +80%, -20%, 25 V Ceramic-Disc Axial-Lead Capacitor122005-103
C33, C340.047 uF, 100 V Radial-Lead Mylar Capacitor21-101473
C350.022 uF, 100 V Radial-Lead Mylar Capacitor21-101223
C360.0047 uF, 100 V Radial-Lead Mylar Capacitor21-101472
C370.001 uF, 100 V Radial-Lead Mylar Capacitor21-101102
C380.0047 uF, 100 V Radial-Lead Mylar Capacitor21-101472
C39, C400.01 uF, 100 V Radial-Lead Mylar Capacitor21-101103
C4147 uF, 10 V Aluminum Electrolytic Fixed Axial-Lead Capacitor24-100476
C42, C430.0047 uF, 100 V Radial-Lead Mylar Capacitor21-101472
C44, C450.001 uF, 100 V Radial-Lead Mylar Capacitor21-101102
C46470 uF, 16 V Aluminum Electrolytic Fixed Axial-Lead Capacitor24-250477
C47-C5622 uF, 16 V Aluminum Electrolytic Fixed Axial-Lead Capacitor24-160226

Acceptable substitute is part no. 24-100477

C57-C840.1 pF, + 10%, 50 V Ceramic-Disc Axial-Lead Capacitor122002-104
C820.001 yF, 100 V Radial-Lead Mylar Capacitor21-101102

Diodes

CRIType-MV5053 Light-Emitting Diode38-MV5053,
CR26.2 V, +5%, 1 W Type-1N4735A Zener Diode131009-001
CR3-CR5100 V, Type-1N914 Switching Diode31-1N914
CRE3.9 V +5% Type-1N748A Zener Diode131000-002
CR7-CR12100 V, Type-1N914 Switching Diode31-1N914

Integrated Circuits

2NType-12L6 Programmable-Array Logic 1137280-001
3AType-Z8002 16-Bit Microprocessor137275-001
3cType-74LS373 Integrated Circuit37-74LS373
3F, 3HCustom Integrated Circuit 10137281-001

(Continued on next page)

3-37

Page 63

Maintenance, Repair, and Parts

Central Processing Unit Printed-Circuit Board Assembly Parts List, continued Pole Position

DesignatorDescriptionPart No.
3M, 4CType-74LS373 Integrated Circuit37-74LS373
4F, 4HCustom Integrated Circuit 10137281-001
4MType-74LS373 Integrated Circuit37-74LS373
4NType-Z8002 16-Bit Microprocessor137275-001
5AType-74LS74 Integrated Circuit37-74LS74
5CType-12L6 Programmable-Array Logic 1137280-001
5DType-74LS367 Integrated Circuit37-74LS367
5EType-74LS244 Integrated Circuit37-74LS244
5JType-74LS367 Integrated Circuit37-74LS367
5KType-74LS244 Integrated Circuit37-74LS244
5LType-74LS368 Integrated Circuit137168-001
5MType-74LS158 Integrated Circuit137203-001
5NType-74LS74 Integrated Circuit37-74LS74
6AType-74LS161 Integrated Circuit37-74LS161
6cType-74LS74 Integrated Circuit37-74LS74
6D-6FType-74LS367 Integrated Circuit37-74LS367
6HCustom Integrated Circuit 08137186-001
6u, 6KType-74LS157 Integrated Circuit37-74LS157
6LType-74LS109 Integrated Circuit37-74LS109
6MType-74LS00 Integrated Circuit37-74LS00
6NType-74S163 Integrated Circuit137274-001
7CType-10L8 Programmable-Array Logic 3137279-001
7DType-Z80A 8-Bit Microprocessor137194-001
7MCustom Integrated Circuit 07137193-001
7NType-74S04 Integrated Circuit37-74804
8DType-74LS138 Integrated Circuit137177-001
8EType-74LS259 Integrated Circuit37-74LS259
8FType-74LS367 Integrated Circuit37-74LS367
8HCustom Integrated Circuit 08137 186-001
8JType-ADC0804 Integrated Circuit137273-001
8KType-4066 Integrated Circuit37-4066
8LType-4584B Integrated Circuit37-4584B
8MType-74LS04 Integrated Circuit37-74LS04
9ECustom Integrated Circuit 52137284-001
OFACustom Integrated Circuit 54137285-001
9FBType-LM324 Integrated Circuit37-LM324
9HCustom Integrated Circuit 06137192-001
9KCustom Integrated Circuit 53137188-001
9MCustom Integrated Circuit 51137187-001
10AType-74LS138 Integrated Circuit137177-001
10CType-74LS374 Integrated Circuit37-74LS374
10DType-74LS174 Integrated Circuit37-74LS174
10E, 10FType-74LS283 Integrated Circuit137204-001
10H, 103Type-74LS273 Integrated Circuit37-74LS273
10K, 10LType-4066 Integrated Circuit37-4066
AType-74LS174 Integrated Circuit37-74LS174
1CType-7497 Integrated Circuit37-7497
METype-74LS273 Integrated Circuit37-74LS273

(Continued on next page)

3-38

Page 64

Pole Position Maintenance, Repair, and Parts

Central Processing Unit Printed-Circuit Board Assembly Parts List, continued

DesignatorDescriptionPart No.
dFType-4051 Integrated Circuit137277-001
41HType-74LS174 Integrated Circuit37-74LS174
WWType-74LS273 Integrated Circuit37-74LS273
41K-11MType-4066 Integrated Circuit37-4066
12AType-74LS174 Integrated Circuit37-7TALS174
12BType-7497 Integrated Circuit37-7497
120Type-74LS161 Integrated Circuit37-74LS161
12DType-74LS393 Integrated Circuit37-74LS393
12H, 12J, 12MType-LM324 Integrated Circuit37-LM324

Random-Access Memories

7ECMOS Random-Access Memory137278-001
7J, 7KRandom-Access Memory137199-001

Read-Only Memories

coElectrically Programmable Read-Only Memory Acceptable136014-106

substitute is part no. 136014-147

3EElectrically Programmable Read-Only Memory136014-203
3LElectrically Programmable Read-Only Memory136014-101
4EElectrically Programmable Read-Only Memory136014-204
4uElectrically Programmable Read-Only Memory136014-102
7FElectrically Programmable Read-Only Memory136014-116
7HElectrically Programmable Read-Only Memory136014-105
7LProgrammable Read-Only Memory Acceptable substitute is part136014-117

no. 136014-160 for Ireland-Built cabinets

11DProgrammable Read-Only Memory136014-118
12EElectrically Programmable Read-Only Memory Acceptable136014-111

substitute is part no. 136014-149

12FElectrically Programmable Read-Only Memory Acceptable136014-110

substitute is part no. 136014-148

Resistors

RI220 2, +5%, ¥ W Resistor110000-221
R2-R82.2 kQ, +5%, V4 W Resistor110000-222
RQ1kQ, +5%, % W Resistor110000-102
R10-R162.2 kQ, +5%, v4 W Resistor110000-222
R17-R201kQ, +5%, % W Resistor110000-102
R21-R261kQ, +5%, % W Resistor110000-102
R27-R342.2 kQ, +5%, % W Resistor110000-222
R35,1kQ, +5%, Y% W Resistor110000-102
R36-R382.2 kQ, +5%, V4 W Resistor110000-222
R39-R431kQ, +5%, % W Resistor110000-102
R4547 Q, +5%, % W Resistor110000-470
R46, R471kQ, +5%, V4 W Resistor110000-102
R49-R51220 2,5%, Y W Resistor110000-221
R52470 2, +5%, Ya W Resistor110000-471
R531kQ, +5%, % W Resistor110000-102
R54470 2, +5%, v4 W Resistor110000-471

(Continued on next page)

3-39

Page 65

Maintenance, Repair, and Parts Pole Position

Central Processing Unit Printed-Circuit Board Assembly Parts List, continued

DesignatorDescriptionPart No.
R55, R561kQ, +5%, % W Resistor110000-102
R57-R60470 Q, +5%, ¥% W Resistor110000-471
R614.7 kQ, +5%, Vs W Resistor110000-472
R6210 kQ, +5%, v4 W Resistor110000-103
R6322 kQ, +5%, % W Resistor110000-223
R6447 kQ, +5%, Vs W Resistor110000-473,
R654.7 kQ, +5%, Ys W Resistor110000-472
R6610 kQ, 5%, V4 W Resistor110000-103
R6722 kQ, +5%, % W Resistor110000-223
R6847 kQ, +5%, Vs W Resistor110000-473
R694.7 kQ, +5%, V4 W Resistor110000-472
R7010 kQ, +5%, % W Resistor110000-103,
R7122 kQ, +5%, % W Resistor110000-223
R7247 kQ, +5%, V4 W Resistor110000-473
R734.7 kQ, +5%, Vs W Resistor110000-472
R7410 kQ, +5%, % W Resistor110000-103
R7522 kQ, +5%, % W Resistor110000-472
R7647 kQ, +5%, % W Resistor110000-473
R77-R801kQ, +5%, % W Resistor110000-102
R81220 2, +5%, v4 W Resistor110000-221
R821k2Q, +5%, % W Resistor110000-102
R83470 Q, +5%, Vs W Resistor110000-471
R841kQ, +5%, % W Resistor110000-102
R852.2 kQ, +5%, Vs W Resistor110000-222
R86330 Q, +5%, % W Resistor110000-331
R871kQ, +5%, % W Resistor110000-102
R88.22 kQ, +5%, V4 W Resistor110000-223
R89-R921kQ, +5%, % W Resistor110000-102
R93, R94330 Q, +5%, % W Resistor110000-331
R951kQ, +5%, % W Resistor110000-102
ROG4.7 kQ, +5%, Vs W Resistor110000-472
R97220 Q, +5%, % W Resistor110000-221
R982.2 kQ, +5%, % W Resistor110000-222
R99.220 2, 5%, % W Resistor110000-221
R1012.2 kQ, +5%, ¥% W Resistor110000-222
R102, R1041kQ, +5%, V% W Resistor110000-102
R103, R1074.7 kQ, +5%, Vs W Resistor110000-472
R106, R108-R1151kQ, +5%, % W Resistor110000-102
R1161.5 kQ, +5%, % W Resistor110000-152
R1171kQ, +5%, % W Resistor110000-102
R1184.7 kQ, +5%, % W Resistor110000-472
R11910 kQ, +5%, % W Resistor110000-103
R120, R12122 kQ, +5%, % W Resistor110000-223
R122120 kQ, +5%, V4 W Resistor110000-124
R123470 2, +5%, % W Resistor110000-471
R12447 kQ, +5%, V4 W Resistor110000-473
R12512 kQ, +5%, % W Resistor110000-123
R1264.7 kQ, +5%, Vs W Resistor110000-472

(Continued on next page)

Page 66

Pole Position Maintenance, Repair, and Parts

Central Processing Unit Printed-Circuit Board Assembly Parts List, continued

DesignatorDescriptionPart No.
R127, R1282.2 kQ, +5%, % W Resistor110000-222
R129, R1303.3 kQ, +5%, Vs W Resistor110000-332
R13110 k2, +5%, % W Resistor110000-103
R13222 kQ, +5%, % W Resistor110000-223
R13315 kQ, +5%, % W Resistor110000-153
R134120 kQ, +5%, % W Resistor110000-124
R135470 Q, +5%, % W Resistor110000-471
R13647 kQ, +5%, % W Resistor110000-473
R13715 kQ, +5%, v4 W Resistor110000-153
R13810 kQ, +5%, % W Resistor110000-103
R13922 kQ, +5%, 4 W Resistor110000-223
R140180 kQ, +5%, % W Resistor110000-184
R141470 Q, +5%, % W Resistor110000-471
R142, R14322 kQ, +5%, Y4 W Resistor110000-223
R144-R1511kQ, +5%, VY W Resistor110000-102
R15247 kQ, +5%, Va W Resistor110000-473
R153470 Q, +5%, Vv W Resistor110000-471
R15410 kQ, +5%, Y% W Resistor110000-103
R15582 kQ, +5%, %4 W Resistor110000-823
R156, R15747 kQ, +5%, % W Resistor110000-473
R15822 kQ, +5%, % W Resistor110000-223
R15947 kQ, +5%, v4 W Resistor110000-473
4«R160100 kQ, +5%, % W Resistor110000-104
wR161-R1652.2 kQ, +5%, vs W Resistor110000-222
R1661kQ, +5%, % W Resistor110000-102
R1672.2 kQ, +5%, % W Resistor110000-222
R1684.7 kQ, +5%, V4 W Resistor110000-472
R169220 kQ, +5%, vs W Resistor110000-224
R170390 kQ, +5%, Vs W Resistor110000-394
R1714.7 kQ, +5%, V4 W Resistor110000-472
R17215 kQ, 5%, V4 W Resistor110000-153
R17347 kQ, +5%, Vs W Resistor110000-473
R17433 kQ, +5%, % W Resistor110000-333
R175,10 k2, +5%, % W Resistor110000-103
R17647 kQ, +5%, ¥% W Resistor110000-473
R1771kQ, +5%, V4 W Resistor110000-102
R1787.5 kQ, +5%, Vs W Resistor110000-752
R179330 kQ, +5%, V4 W Resistor110000-334
R180, R18147 kQ, +5%, V4 W Resistor110000-473
R1821kQ, +5%, % W Resistor110000-102
R18322 kQ, +5%, V4 W Resistor110000-223
R18415 kQ, +5%, ¥% W Resistor110000-153
R18510 kQ, +5%, ¥% W Resistor110000-103
R1861k2, +5%, % W Resistor110000-102
R187330 kQ, +5%, ¥% W Resistor110000-334
R18810 k2, +5%, 4 W Resistor110000-103
R189, R19047 kQ, +5%, % W Resistor110000-473

1k2, +5%, % W Resistor 110000-102 re) R191 (Continued on next page)

Page 67

Maintenance, Repair, and Parts

Central Processing Unit Printed-Circuit Board Assembly Parts List, continued Pole Position

DesignatorDescriptionPart No.
R19275 kQ, +5%, % W Resistor110000-753
R19315 kQ, +5%, v4 W Resistor110000-153
R19447 kQ, +5%, VY W Resistor110000-473
R19510 kQ, +5%, Ve W Resistor110000-103
R1961kQ, +5%, % W Resistor110000-102
R197, R19847 kQ, +5%, % W Resistor110000-473
R1991kQ, +5%, %4 W Resistor110000-102
R20047 kQ, +5%, % W Resistor110000-473
R20115 kQ, +5%, V4 W Resistor110000-153
R20210 kQ, +5%, % W Resistor110000-103
R2031k, +5%, % W Resistor110000-102
R204, R20547 kQ, +5%, % W Resistor110000-473
R2061kQ, +5%, % W Resistor110000-102
R20720 kQ, +5%, % W Resistor110000-203
R20810 kQ, +5%, % W Resistor110000-103
R20920 kQ, +5%, % W Resistor110000-203
R21010 kQ, 5%, Y% W Resistor110000-103
R21120 kQ, +5%, % W Resistor110000-203
R21210 kQ, +5%, % W Resistor110000-103
R21320 kQ, +5%, % W Resistor110000-203
R21410 kQ, +5%, % W Resistor110000-103
R21520 kQ, +5%, % W Resistor110000-203
R21610 kQ, +5%, % W Resistor110000-103
R21720 kQ, +5%, % W Resistor110000-203
R21810 kQ, +5%, % W Resistor110000-103
R21920 kQ, +5%, % W Resistor110000-203
R22027 kQ, +5%, Y W Resistor110000-273
R2231kQ, +5%, % W Resistor110000-102
R225-R2311kQ, +5%, % W Resistor110000-102
R231-R2382.2 kQ, +5%, % W Resistor110000-222
R239-R2441kQ, +5%, % W Resistor110000-102
R245100 2, +5%, % W Resistor110000-101
R246150 kQ, +5%, % W Resistor110000-154
1E2.2 kQ, + 2%, Dual-Intine-Package Resistor Network118003-222
ON1kQ, +2%, Dual-Inline-Package Resistor Network118003-102

Sockets

3A40-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C40
3E, 3F28-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C28
3H28-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C28
3L28-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C28
4E, 4F28-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C28
4H28-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C28
4.28-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C28
4N40-Contact Medium-insertion-Force Integrated Circuit Socket79-42C40

3-42 (Continued on next page) &

Page 68

Pole Position Maintenance, Repair, and Parts

Central Processing Unit Printed-Circuit Board Assembly Parts List, continued

DesignatorDescriptionPart No,
6H-9H28-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C28
7D40-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C40
7E, 7F24-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C24
7H28-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C28
7M28-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C28
8A28-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C28
8c28-Contact Medium-Insertion-Force integrated Circuit Socket79-42C28
9c28-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C28
9E42-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C42
OFA28-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C28
9K42-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C42
9M42-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C42
12E, 12F28-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C28

Switches

QJA8-Station, Single-Throw, Dual-Inline-Package Bit Switch66-118PIT
9L8-Station, SingleThrow, Dual-Inline-Package Bit Switch66-118PIT

Transistors

QiType-2N3906 40 V, 1 W, PNP Transistor33-2N3906
Q2Type-2N3904 60 V, 350 mW, NPN Transistor34-2N3904
Q3Type-MPS-A92 300 V, 500 mA, PNP Transistor33-MPSAQ2
Q4Type-2N3904 60 V, 350 mW, NPN Transistor34-2N3904
Q5, Q6Type-2N6044 80 V, 8 A, Darlington NPN Transistor34-2N6044

Miscellaneous

BT13.6 V, 100 mA Nickel-Cadmium Battery171028-001
wtLead-Spring Socket Terminal179131-001

Test Point Acceptable substitute is part no. 020670-01 179051-001 Jumper Staple 150009-001

Q5, Q6Nylon Snap-In Fastener81-4302
Page 69

Pole Position Maintenance, Repair, and Parts

iar a a a ia iti =) =

iene 1 2 3 4 5 6 7 8 9 10 n 12 13

Figure 3-20 Pole Position Video Printed-Circuit Board Assembly A039187-21

Page 70

Pole Position Maintenance, Repair, and Parts

Pole Position Video Printed-Circuit Board Assembly Parts List

DesignatorDescriptionPart No.

Capacitors

c2470 uF, 25 V Aluminum Electrolytic Axial-Lead Capacitor24-250477

C3-C17 22 uF, 16 V Aluminum Electrolytic Axial-Lead Capacitor Acceptable substitute is part no. 24-250226 24-160226

C18-C570.1 uF, + 80, -20%, 50 V Ceramic Disk Radial-Lead Capacitor122002-104
C5868 pF, 100 V, Mica Capacitor128002-680
C5922 pF, 100 V, Mica Capacitor128002-220

Diodes

CRIType-MV5053 Light-Emitting Diode38-MV5053,
CR2Type-1N4735A, 6.2 V, 1 W Zener Diode131009-001

Inductors

L1-L31 wH, ¥2 W Inductor141007-001
L4100 wH, + 10% Inductor141002-001

Integrated Circuits

2AType-74LS138 Integrated Circuit137177-001
2EType-74LS74 Integrated Circuit37-74LS74
2HType-74LS139 Integrated Circuit37-74LS139
2Type-74LS10 Integrated Circuit37-74LS10
2KType-74LS368 Integrated Circuit137 168-001
3BType-74LS283 Integrated Circuit137204-001
3cType-74LS283 Integrated Circuit137204-001
3DType-74LS283 Integrated Circuit137204-001
3HType-74LS175 Integrated Circuit37-74LS175
BU, 4dType-74LS174 Integrated Circuit37-74LS174
3KType-74LS283 Integrated Circuit137204-001
3LType-74LS283 Integrated Circuit137204-001
3MType-74LS02 Integrated Circuit37-74LS02
4BType-74LS367 Integrated Circuit37-74LS367
4cType-74LS367 Integrated Circuit37-74LS367
4HType-74LS157 Integrated Circuit37-74LS157
4KType-74LS174 Integrated Circuit37-74LS174
4M, 5MType-74LS298 Integrated Circuit137201-001
4N, 5NType-74LS283 Integrated Circuit137204-001
5BType-74LS174 Integrated Circuit37-74LS174
5C.Type-74LS174 Integrated Circuit37-74LS174
5DType-74LS174 Integrated Circuit37-74LS174
5EType-74LS245 Integrated Circuit37-74LS245,
5F, 6FType-74LS245 Integrated Circuit37-74LS245,
5HType-74LS175 Integrated Circuit37-74LS175
buType-74LS273 Integrated Circuit37-74LS273
6AType-74S04 Integrated Circuit37-74S04
6BType-74LS368 Integrated Circuit137168-001
6CType-74LS08 Integrated Circuit37-74LS08
6HType-74LS245 Integrated Circuit37-74LS245
6JType-74LS245 Integrated Circuit37-74LS245
6KType-74LS245 Integrated Circuit37-74LS245
6M, 7MType-74LS273 Integrated Circuit37-74LS273
7BType-74S163 Integrated Circuit Acceptable substitute is part no.137274-001

137287-001 or -002

7CType-74S04 Integrated Circuit37-74S04
7DType-74LS32 Integrated Circuit37-74LS32

(Continued on next page)

Page 71

Maintenance, Repair, and Parts Pole Position

Pole Position Video Printed-Circuit Board Assembly Parts List, continued e

DesignatorDescriptionPart No.
7LType-74LS273 Integrated Circuit37-74LS273
8BType-74S00 Integrated Circuit37-74S00
8C,9CType-74LS157 Integrated Circuit37-74LS157
8DType-74S158 Integrated Circuit137312-000
8EType-74LS158 Integrated Circuit137203-001
8L,9LType-74LS174 Integrated Circuit37-74LS174
9BType-74LS20 Integrated Circuit37-74LS20
9DType-74LS298 Integrated Circuit137201-001
9E, 10EType-74LS257 Integrated Circuit37-74LS257
9HType-74S161 Integrated Circuit137287-001
QJType-74S161 Integrated Circuit137287-001
9KType-7497 Integrated Circuit37-7497
9M, 10MType-74LS283 Integrated Circuit137204-001
ONType-74LS85 Integrated Circuit37-74LS85
10BType-74LS74 Integrated Circuit37-74LS74
10CType-74LS174 Integrated Circuit37-74LS174
10DType-74LS368 Integrated Circuit137168-001
10HType-74S161 Integrated Circuit137287-001
10JType-74S161 Integrated Circuit137287-001
10KType-74S161 Integrated Circuit137287-001
10LType-74S161 Integrated Circuit137287-001
10NType-74LS85 Integrated Circuit37-74LS85
11BType-74107 Integrated Circuit Acceptable substitute is part no.37-74107

137169-001

iFType-74LS174 Integrated Circuit37-T4LS174
1HType-74LS174 Integrated Circuit37-74LS174&
WWType-74LS273 Integrated Circuit37-74LS273
WKType-74LS139 Integrated Circuit37-74LS139
1bType-74LS373 Integrated Circuit37-74LS373
11MType-74LS373 Integrated Circuit37-74LS373
12BType-74LS08 Integrated Circuit37-74LS08
12FType-74LS86 Integrated Circuit37-74LS86
13FType-74LS20 Integrated Circuit37-74LS20

For -21 version only

2FType-07 Custom Integrated Circuit137193-001
3NType-02 Custom Integrated Circuit137190-001
4DType-09 Custom Integrated Circuit137282-001
SL, 6LType-03 Custom Integrated Circuit137283-001
7EType-04 Custom Integrated Circuit137191-001
8NType-02 Custom Integrated Circuit137190-001
13HType-02 Custom Integrated Circuit137190-001

Random-Access Memories

SE, 4ERandom-Access Memory (200 ns) Acceptable substitute is part no.137 198-001

137211-001 (150 ns)

3F, 4FRandom-Access Memory (200 ns) Acceptable substitute is part no.137198-001

137211-001 (150 ns)

7F, 8FType-2114-2 (200 ns) Random-Access Memory90-7036
7H, 8HType-2114-2 (200 ns) Random-Access Memory90-7036
7J, BdType-2114-2 (200 ns) Random-Access Memory90-7036
7K, 8KType-2114-2 (200 ns) Random-Access Memory90-7036
QF, 10F55 ns Random-Access Memory137199-001

(Continued on next page)

Page 72

Pole Position Maintenance, Repair, and Parts

Pole Position Video Printed-Circuit Board Assembly Parts List, continued

DesignatorDescriptionPart No.

Programmable Read-Only Memories

2BType-82S129(17) Programmable Read-Only Memory136014-144
2cType-82S129(16) Programmable Read-Only Memory136014-143
2DType-82S129(15) Programmable Read-Only Memory136014-142
4LType-82S137(12) Programmable Read-Only Memory136014-145
5KType-82S129(11) Programmable Read-Only Memory136014-141
6DType-82S123(14) Programmable Read-Only Memory136014-136
6EType-82S123(13) Programmable Read-Only Memory136014-135
8MType-828129(10) Programmable Read-Only Memory136014-140
11CType-82S129(9) Programmable Read-Only Memory136014-139
11DType-82S129(8) Programmable Read-Only Memory136014-138
11EType-82S129(7) Programmable Read-Only Memory136014-137
12HType-828137(6) Programmable Read-Only Memory136014-146

For -21 version only

aLElectrically Programmable Read-Only Memory Acceptable136014-127

substitute is part no. 136014-158

2MElectrically Programmable Read-Only Memory Acceptable136014-128

substitute is part no. 136014-159

2NElectrically Programmable Read-Only MemoryAcceptable136014-134

substitute is part no. 137205-001

6NElectrically Programmable Read-Only MemoryAcceptable136014-133

substitute is part no. 137205-001

7NElectrically Programmable Read-Only MemoryAcceptable136014-132

substitute is part no. 137205-001

TiNElectrically Programmable Read-Only Memory Acceptable136014-231

substitute is part no. 136014-131

12dElectrically Programmable Read-Only Memory Acceptable136014-120

substitute is part no. 136014-157

12KElectrically Programmable Read-Only Memory Acceptable136014-122

substitute is part no. 136014-153

12LElectrically Programmable Read-Only Memory Acceptable136014-124

substitute is part no. 136014-155

12NElectrically Programmable Read-Only Memory Acceptable136014-126

substitute is part no. 136014-157

13dElectrically Programmable Read-Only Memory Acceptable136014-119

substitute is part no. 136014-150

13KElectrically Programmable Read-Only Memory Acceptable136014-121

substitute is part no. 136014-152

13LElectrically Programmable Read-Only Memory Acceptable136014-123

substitute is part no. 136014-154

13NElectrically Programmable Read-Only Memory Acceptable136014-125

substitute is part no. 136014-156 Resistors

R1-R92.2 kQ, +5%, v4 W Resistor110000-222
R10-R241kQ, +5%, % W Resistor110000-102
R25-R40470 2, 5%, V4 W Resistor110000-471
R41-R484.7 kQ, +5%, v4 W Resistor110000-472
R49-R521kQ, +5%, % W Resistor110000-102
R55-R58-1kQ, +5%, Y W Resistor110000-102
R59220 2, +5%, % W Resistor110000-221
R60470 Q, +5%, v4 W Resistor110000-471

(Continued on next page)

Page 73

Maintenance, Repair, and Parts Pole Position

Pole Position Video Printed-Circuit Board Assembly Parts List, continued ‘

DesignatorDescriptionPart No.
R611kQ, +5%, % W Resistor110000-102
R622.2 kQ, +5%, % W Resistor110000-222
R66220 2, +5%, % W Resistor110000-221
R67470 Q, +5%, % W Resistor110000-471
R68.1kQ, +5%, % W Resistor110000-102
R692.2 kQ, +5%, % W Resistor110000-222
R73220 Q, +5%, % W Resistor110000-221
R74470 Q, +5%, % W Resistor110000-471
R751kQ, +5%, % W Resistor110000-102
R762.2 kQ, +5%, Vs W Resistor110000-222
R801kQ, +5%, 4 W Resistor110000-102
R81100 2, +5%, % W Resistor110000-101
R82-R851kQ, +5%, % W Resistor110000-102
R86220 Q, +5%, % W Resistor110000-221
R87-R981kQ +5%, %4 W Resistor110000-102
R9910 kQ, +5%, % W Resistor110000-103
R100220 Q, +5%, Y% W Resistor110000-221
R10110 kQ, +5%, % W Resistor110000-103
R102470 kQ, +5%, V% W Resistor110000-471
R103-R10582 Q, +5%, Vs W Resistor110000-820
1B2.2 kQ, +2%, 15-Element, Dual-Inline Package Resistor Pack118003-222
1K2.2 kQ, +2%, 15-Element, Dual-Inline Package Resistor Pack118003-222

Sockets

QF28-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C28@
2u28-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C28
2M28-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C28
2N24-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C24
36, 4E24-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C24
3F, 4F24-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C24
3N28-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C28
4D24-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C24
5L, 6L18-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C18
6N, 7N24-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C24
7E28-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C28
8N28-Contact Medium-Iinsertion-Force Integrated Circuit Socket79-42C28
41N24-Contact Medium-Insertion-Force Integrated Circuit Socket79-42024
12J, 13028-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C28
12K, 13K28-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C28
12L, 13L28-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C28
12N, 13N28-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C28
13H28-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C28

Transistor

Q4Type-2N3904, 60 V, 1 W, NPN Transistor34-2N3904

Miscellaneous Test Points Acceptable substitute is part no. 020670-01 179051-002

Y1B24.576 MHz Crystal Acceptable substitute is part no. 144004-002144004-003
Page 74

Pole Position Maintenance, Repair, and Parts

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific written permission of Atari, Inc., Sunnyvale, CA. This drawing is ‘only conditionally issued, ‘and either receipt nor possession thereof confers or transfers any right in. or license to use, the ‘subject matter of the drawing or any design or technical information shown thereon, nor any right to reproduce this drawing or any part thereof. Except for manufacture by vendors of Atari Inc. and for manulacture under the corporation's written license, ‘no right to reproduce this drawing is granted oF the subject mat- {er thereof unless by written agreement with or written permission from the corporation.

R24,10.,7W)

Figure 3-21 Regulator/Audio I! PCB Assembly U.S.-Built Cabinet A035435-01 G

3-49

Page 75

Maintenance, Repair, and Parts

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific written permission of Atari, Inc., Sunnyvale, CA. This ‘drawing is only conditionally issued, and neither receipt nor possession thereof confers of transfers any right in, oF license to use, the subject matter of the drawing or any design or technical information shown thereon, nor any tight to reproduce this drawing or any part thereof. Except for manufacture by vendors of Atari, Inc., and for manufac ture under the corporation's written license, no right to reproduce this drawing is granted or the subject matter thereot uniass by written agreement with or written permis sion from the corporation. Pole Position

oe) a> — [res 12. 7W!

Figure 3-22 Regulator/Audio || PCB Assembly lreland-Built Cabinet A035435-05 A

3-50

Page 76

Pole Position Maintenance, Repair, and Parts

Regulator/Audio || PCB Assembly X) Parts List Assemblies and components in the following parts list are shown in Figures 3-21 and 3-22.

DesignatorDescriptionPart No.

Capacitors

For -01* and -05** versions

C1470 uF, 25 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor24-250477
C20.001 uF, 25 V, Ceramic-Disc Axial-Lead Capacitor122002-102
C80.22 uF, 25 V, Ceramic-Disc Axial-Lead Capacitor122004-224
C131000 pF, 25 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor24-250108

For -01 version

c30.1 uF, 25 V, Ceramic-Disc Axial-Lead Capacitor29-088
C4470 yF, 25 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor(24-250477
C50.01 pF, 25 V Minimum, Ceramic-Disc Axial-Lead Capacitor Acceptable100015-103

substitute is part no. 122005-103

C60.22 uF, 25 V, Ceramic-Disc Axial-Lead Capacitor122004-224
C70.001 uF, 25 V, Ceramic-Disc Axial-Lead Capacitor122002-102
C9, C103300 uF, 35 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor24-350338
ci0.1 uF, 25 V, Ceramic-Disc Axial-Lead Capacitor29-088
C12470 pF, 25 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor24-250477
C140.01 pF, 25 V Minimum, Ceramic-Disc Axial-Lead Capacitor Acceptable100015-103

substitute is part no. 122005-103

C150.22 uF, 25 V, Ceramic-Disc Axial-Lead Capacitor122004-224
C160.001 uF, 25 V, Ceramic-Disc Axial-Lead Capacitor122002-102
C170.22 uF, 25 V, Ceramic-Disc Axial-Lead Capacitor122004-224
C18, C193300 HF, 35 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor24-350338
C20, C210.1 uF, 25 V, Ceramic-Disc Axial-Lead Capacitor29-088
C22, C231 uF, 50 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor24-500105

Diodes

For -01 and -05 versions

CR1Type-1N4002, 1 A, 100 V Silicon Rectifier Diode31-1N4002
CR4Type-1N4002, 1 A, 100 V Silicon Rectifier Diode31-1N4002

Integrated Circuits

For -01 and -05 versions

QiType-LM305, 5 V, Linear Voltage Regulator37-LM305,

For -01 version

Q5Type-TDA2002A, 8 W, Linear Audio Amplifier Integrated Circuit137151-002
Q7Type-TDA2002A, 8 W, Linear Audio Amplifier Integrated Circuit137151-002

(Continued on next page)

Jb *Acceptable substitutes are A035435-02 or -04. **Acceptable substitutes are A035435-01, -02, or -04.

3-51

Page 77

Maintenance, Repair, and Parts

Regulator/Audio || PCB Assembly Parts List, continued Pole Position

DesignatorDescriptionPart No.

Resistors

For -01 and -05 versions

R1270 2, +5%, % W Resistor110000-271
R333 Q2, +5%, % W Resistor110000-330
R4100 2, +5%, % W Resistor110000-101
R52.7 Q, +5%, 1 W Resistor110009-027
R63.9 kQ, +5%, % W Resistor110000-392
R775 kQ, +5%, % W Resistor110000-752
R81 kQ Vertical PCB-Mounting Cermet Potentiometer Acceptable19-315102

substitute is part no. 119002-102

R240.1 2, +3%, 7 W Wirewound Resistor19-100P1015,
R29, R3010 Q, +5%, % W Resistor110000-100

For -01 version

RQ220 Q, +5%, ¥2 W Resistor110001-221
R101, +5%, % W Resistor110000-010
R1110 2, +5%, % W Resistor110000-100
R12100 2, +5%, % W Resistor110000-101
R13, R1410 kQ2, +5%, ¥% W Resistor110000-103
R191, +5%, % W Resistor110000-010
R2010 2, +5%, % W Resistor110000-100
R21220 2, +5%, V2 W Resistor110001-221
R22100 2, +5%, % W Resistor110000-101
R27, R281kQ, +5%, % W Resistor110000-102

Transistors

For -01 and -05 versions

Q2Type-TIP32 PNP Power Transistor33-TIP32
Q3Type-2N3055 NPN Silicon Transistor34-2N3055

Mechanical Parts

For -01 and -05 versions

J66-Position Connector Receptacle79-58306
J79-Position Connector Receptacle79-58308
Q3#6-32 x Y-Inch Cross-Recessed Pan-Head Corrosion-Resistant Stee!72-1608C

Machine Screw

Q2, Q3#6-32 Nut/Washer Assembly75-99516
Q2Thermally Conductive Silicon Insulator78-16014
Q3Thermally Conductive Silicon Insulator78-16008
Q5#6-32 x %-Inch Binder-Head Nylon Screw75-F60405

Heat Sink 034531-01 Test Point Acceptable substitute is part no. 020670-01 179051-001

For -01 version

J84-Position Connector Receptacle79-58354
Qs#6 x %-Inch Cross-Recessed Pan-Head Thread-Forming Type-AB Zinc-72-6606S,

Plated-Steel Screw

3-52

Page 78

Pole Position Maintenance, Repair, and Parts

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific witten permission of Atari, Inc., Sunnyvale, CA. This drawing is ‘only conditionally issued, ‘and neither receipt nor possession thereof confers or transfers any right in, or license to use, the subject matter of the drawing or any design or technical information shown thereon. nor any right to reproduce this drawing or any part thereot. Except for manulacture by vendors of ‘ari, Inc, and for manufacture under the corporation's written Nicense, no right to reproduce this drawing is granted or the subject matter thereot unless by wrlten agreement with or wntten permission trom the corporation

Gc Go e220 co c23 GD ome g c24 Ci} Gocs c2s oD ace a oD cD cD co co sD ep cs! wpeiz os2 fi Gos <33 4D coca oS4+ fon ras cD pac Cop Coa too co Cop Go <39° cop co c40 CO Cpe2:

ape Bea GOoc43 9044, 470PF aces Co cac,470°F 03647 ,.470Pe 1c

fl

Go-c5s4 Gpcss [.

LL

Figure 3-23 EMI Shield PCB Assembly A037667-01 A

3-53

Page 79

Maintenance, Repair, and Parts

EMI Shield PCB Assembly Parts List

Assemblies and components in the following parts list are shown in Figure 3-23. Pole Position

DesignatorDescriptionPart No.

Capacitors

C1-C50.1 uF, +80, -20%, 50 V Ceramic-Disk Radial-Lead Capacitor122002-104
C6-C100.01 uF, +80, -20%, 25 V Ceramic-Disk Radial-Lead Capacitor122005-103
C120.01 pF, + 80, -20%, 25 V Ceramic-Disk Radial-Lead Capacitor122005-103
C13-C150.1 uF, +80, -20%, 50 V Ceramic-Disk Radial-Lead Capacitor122002-104
Cié0.01 uF, +80, -20%, 25 V Ceramic-Disk Radial-Lead Capacitor122005-103
C17-C240.1 uF, +80, -20%, 50 V Ceramic-Disk Radial-Lead Capacitor122002-104
C250.01 uF, +80, -20%, 25 V Ceramic-Disk Radial-Lead Capacitor122005-103
C27-C310.01 uF, +80, -20%, 25 V Ceramic-Disk Radial-Lead Capacitor122005-103
32,0330.1 uF, +80, -20%, 50 V Ceramic-Disk Radial-Lead Capacitor122002-104
C34-C390.01 uF, +80, -20%, 25 V Ceramic-Disk Radial-Lead Capacitor122005-103
C40-C430.1 pF, +80, -20%, 50 V Ceramic-Disk Radial-Lead Capacitor122002-104
C440.471 uF, +80, -20%, 100 V Ceramic-Disk Radial-Lead Capacitor122016-471
C450.001 uF, +80, -20%, 100 V Ceramic-Disk Radial-Lead Capacitor122016-102
C46,C470.471 uF, +80, -20%, 100 V Ceramic-Disk Radial-Lead Capacitor122016-471
C480.1 uF, +80, -20%, 50 V Ceramic-Disk Radial-Lead Capacitor122002-104
C54,C550.1 uF, +80, -20%, 50 V Ceramic-Disk Radial-Lead Capacitor122002-104

Connectors

P1930-Pin Card-Edge Connector Acceptable substitute is part no. 179046-030179073-030
P2044-Pin Card-Edge Connector Acceptable substitute is part no. 179046-044179073-044

3-54

Page 80

Pole Position Maintenance, Repair, and Parts

9 H. Power Supply Assembly

WARNING A035888-01 Fuse cover must be in place dur- (Transformer assy.) ing game operation.

A021084-xx (Voltage plugs) 29-053 (Capacitor) 03454401 (Fuse biock cover)

79-4411001 (Fuse post) 78-70501SC (Capacitor bracket) 46-2017002 (Fuse)

29.053 (Capacitor) A035891-02 034482.02 (Fuse harness assy.) \\ > . “a (Chassis) 46-301203 (Fuse)

037639-01 (Label)

A034630-01 (Filter Assy.)

78-70501SC 46-2014002 (Bracket) (Fuses)

79-15021001 (Terminal block) (Power harness)

A034629-01 3A-MDA3501 (Rectifier) (AC harness)

Figure 3-24 Power Supply Assembly ) A0376721-04 & -05 G

Page 81

Maintenance, Repair, and Parts Pole Position

Power Supply Assembly Parts List

Assemblies and components in the following parts list are shown in Figure 3-24.

Part No. Description (Reference Designations in Bold)

A021084-01Voltage Plug for 100V(90-110 VAC) (violet)
A021084-02Voltage Plug for 120V(105-135 VAC) (yellow)
A021084-04Voltage Plug for 220V(200-240 VAC) (biue)
A021084-05,Voltage Plug for 240V(220-260 VAC)(brown)

A034629-01 AC Harness Assembly

A034630-01RFI Filter Assembly(FL1—designation not marked)

A035888-01 Upright and Cabaret Transformer Assembly (11) Acceptable substitute is part no. A035888-02 A035890-01 Power Harness Assembly (J2) A035891-02 Fuse Harness Assembly (F2-F6) 29-053 27,000 pF 15V DC Electrolytic Capacitor (C1) 3A-MDA3501 Bridge Rectifier, Type MDA 3501 (CR1)

46-20140024A, 250 V, 3AG Slow-Blow Glass Cartridge-Type Fuse(F2, F4-F6)
46-20170027 A, 250 V, 3AG Slow-Blow Glass Cartridge-Type Fuse(F1)
46-301253,25 A, 32 V, 3AG Slow-Blow Glass Cartridge-Type Fuse(F3)

78-2708 Nylon Type 6/6 Hole Bushing with %-Inch Inside Diameter x %,-Inch Outside Diameter x ‘%-Inch Thick 78-70501SC 2-Inch Diameter Capacitor Mounting Bracket (C1) 79-15021001 2-Circuit Single-Row Terminal Block (located under F4) 79-3206, 5-Position 3AG Fuse Block with ¥%-Inch Quick-Disconnect Terminals (F2-F6) 79-4411001 Panel-Mounting Non-Indicating 3AG Cartridge-Type Fuse Post (F1) 034482-02 Power Supply Chassis

034544-01Fuse Block Cover(F2-F6)
037639-03, -04Label for Fuse Value(F1)
037641-01Label for Fuse Values(F2-F6)

A037671-04 power supply has the 120 V plug. ‘A037671-05 has the 100 V, 220 V and 240 V plugs. ‘A037671-06 has the 220 V and 240 V plugs.

3-56

Page 82

Pole Position

g Glossary of Terms

AC Alternating current; from zero it rises to a maximum positive level, then passes through zero again to a maximum negative level. ACTIVE STATE The true state of a signal. For example: The active state for START is low.

ADDRESS A value that identifies a specific location of data in memory; normally expressed in hexadecimal notation. ANALOG Measurable in an absolute quantity (as opposed to on or off). Analog devices are volume controls, light dimmers, stereo amplifiers, etc. ANODE The positive (arrow) end of a diode. AMPLIFIER A device used to increase the strength of an applied signal.

AMPLITUDE The maximum instantaneous value of a waveform pulse from zero. ASTABLE Having no normal state. An astable device will free-run or oscillate as long as operating voltage is applied. The oscillation frequency is usually controlled by external circuitry. AUXILIARY COIN SWITCH A momentary-contact pushbutton switch with a black cap located on the utility panel. The auxiliary coin switch adds credits to the game without activating the coin counter. BEZEL A cut, formed, or machined retention device, such as the conical device used to mount a pushbutton switch to a control panel, or the formed device used to frame the video display screen. BIDIRECTIONAL Able to send or receive data on the same line (e.g., the data bus of a microprocessor). BINARY A number system that expresses all values by using two digits (0 and 1). BIT A binary digit; expressed as a 1 or ad. BLANKING Turning off the beam on a cathoderay tube during retrace. BLOCK DIAGRAM A drawing in which functional circuitry units are represented by blocks. Very useful during initial troubleshooting. BUFFER

  • An isolating circuit designed to eliminate the reaction of a driven circuit on the circuits driving it (e.g., a buffer amplifier).
  • A device used to supply additional drive capability. BUS An electrical path over which information is transferred from any of several sources to any of several destinations.

CAPACITOR A device capable of storing electrical energy. A capacitor blocks the flow of DC current while allowing AC current to pass.

CATHODE The negative end of a diode. CHIP An integrated circuit comprising many circuits on a single wafer slice.

CLOCK A repetitive timing signal for synchronizing system functions.

COINCIDENCE Occurring at the same time. COIN COUNTER A 6-digit electro-mechanical device that counts the coins inserted in the coin mechanism(s). COIN MECHANISM A device on the inside of the coin door that inspects the coin to determine if the correct coin has been inserted. COMPLEMENTARY Having opposite states, such as the outputs of a flip-flop. COMPOSITE SYNC Horizontal and vertical synchronization pulses that are bused together into a single signal. This signal provides the timing necessary to keep the display in synchronization with the game circuitry, Glossary

COMPOSITE VIDEO Complete video signal from the game system to drive the display circuitry, usually comprising H SYNC, V SYNC, and the video. CREDIT One play for one person based on the game switch settings. CRT Cathode-ray tube. DATA General term for the numbers, letters, and symbols that serve as input for device processing. DARLINGTON A two-transistor amplifier that provides extremely high gain. Dc Direct current, meaning current flowing in one direction and of a fixed value. DEFLECTION YOKE Electro-magnetic coils around the neck of a cathode-ray tube. One set of coils deflects the electron beam horizontally and the other set deflects the beam vertically. DIAGNOSTICS A programmed routine for checking circuitry. For example: the self-test is a diagnostic routine. DIODE A semiconductor device that conducts in only one direction. DISCRETE Non-integrated components, such as. resistors, capacitors, and transistors. DMA Direct memory access. DMA is a process of accessing memory that bypasses the microprocessor logic. DMA is normally used for transferring data between the input/output ports and memory. DOWN TIME The period during which a game is malfunctioning or not operating correctly due to machine failure. EAROM Electrically alterable read-only memory (see ROM). The EAROM is a memory that can be changed by the application of high voltage. FLYBACK A step-up transformer used in a display to provide the high voltage.

GLA

Page 83

Glossary

GATE

  • A circuit with one output that responds when and only when a certain combination of pulses is present at the inputs.
  • A circuit in which one signal switches another signal on and off.
  • To control the passage of a pulse or signal. HARNESS A prefabricated assembly of insulated wires and terminals ready to be attached to a piece of equipment. HEXADECIMAL A number system using the equivalent of the decimal number 16 as a base. The symbols 0-9 and A-F are usually used. IMPLODE To burst inward; the inward collapse of a vacuum tube. vo Input/Output. IRQ Interrupt request. IRQ is a control signal to the microprocessor that is generated by external logic. This signal tells the microprocessor that external logic needs attention. Depending on the program, the processor may or may not respond. LED The abbreviation for a light-emitting diode. LOCKOUT COIL Directs coins into the coin return box when there is no power to the game. LOGIC STATE The binary (1 or 0) value at the node of a logic element or integrated circuit during a particular time. Also called the logic level. The list below shows the voltage levels corresponding to the logic states (levels) ina TTL system. Logic 0, Low = 0 VDC to +0.8 VDC Grey Area (Tri-State Level) = +0.8 VDC to +2.4 VDC Logic 1, High = +2.4 VDC to +5 VDC MULTIPLEXER A device that takes several lowspeed inputs and combines them into one high-speed data stream for simultaneous transmission on a single line.

GL2 NMI Non-maskable interrupt. NMI is a request for service by the microprocessor from external logic. The microprocessor cannot ignore this interrupt request. PAGE A subsection of memory. A read-only memory device (see ROM) is broken into discrete blocks of data. These blocks are called pages. Each block has X number of bytes. PCB The abbreviation for a printed-circuit

PHOTOTRANSISTOR A transistor that is activated by an external light source. POTENTIOMETER

  • A resistor that has a continuously moving contact which is generally mounted on a moving shaft. Used chiefly as a voltage divider. Also called a pot (slang).
  • An instrument for measuring a voltage by balancing it against a known voltage. RAM Random-access memory. A device for the temporary storage of data. RASTER-SCAN DISPLAY Adisplay system whereby images are displayed by continuously scanning the cathode-ray tube horizontally and vertically with an electron beam. The display system controls the intensity of the electron beam. RETRACE In a raster-scan display, retrace is the time during which the cathoderay tube electron beam is resetting either from right to left or from bottom to top. RESISTOR A device designed to have a definite amount of resistance. Used in circuits to limit current flow or to provide a voltage drop. ROM Read-only memory. A device for the permanent storage of data. SIGNATURE ANALYSIS A process of isolating digital logic faults at the component level by means of special test equipment called signature analyzers. Basically, signature analyzers (e.g., the ATARI® CAT Box) convert lengthy bit Pole Position

streams into four-digit hexadecimal signatures. The signature read by the analyzer at each circuit node is then compared with the known good signature for that node. This process continues until a fault is located. TROUBLESHOOT The process of locating and repairing a fault. VECTOR A line segment drawn between specific X and Y coordinates on a cathode-ray tube. WATCHDOG A counter circuit designed to protect the microprocessor from self-destruction if a program malfunction occurs. If a malfunction does occur, the counter applies continuous pulses to the reset line of the microprocessor, which causes the microprocessor to keep resetting. X-Y DISPLAY A display system whereby images are displayed with vectors. ZENER DIODE A special diode used as a regulator. Its main characteristic is breaking down at a specified reverse-bias (Zener) voltage.

Page 84

pe Beek Bees Ben Bees Bees Res. En 2a 1 RUE SWE URW SUE SUSUR

Y clee Neal Natee Sani ated 5 Natal ated, Nata Ns

Warranty

Seller warrants that its printed-circuit boards and parts thereon are free from defects in material and workmanship under normal use and service for a period of ninety (90) days from date of shipment. Selier warrants that its video displays (in games supplied with displays) are free from defects in material and workmanship under normal use and service for a period of thirty (30) days from date of shipment. None of the Seller's other products or parts thereof are warranted.

lf the products described in this manual fail to conform to this warranty, Sellers’ sole fiability shall be, at its option, to repair, replace, or credit Buyer's account for such products which are returned to Seiler during said warranty period, provided:

{a) Seller is promptly notified in writing upon discovery by Buyer that said products are defective:

  • Such products are returned prepaid to Sellers’ plant, and
  • Seller's examination of said products discloses to Seller's satisfaction that such aileged defects existed and were not caused by accident, misuse, neglect, alteration. improper repair installation or improper testing.

In no event shall Seller be liable for loss of profits, loss of use, incidental or consequential damages.

Except for any express warranty set forth in a written contract between Seller and Buyer which contract supersedes the terms of this order, this warranty is expressed in lieu of all other warranties expressed or implied, including the implied warranties of merchantability and fitness for a particular purpose, and of all other obligations or liabilities on the Seller's part, and it neither assumes nor authorizes any other person to assume for the Seller any other liabilities in connection with the sale of products under this order.

The use of any non-Atari parts may void your warranty, according to the terms of the warranty. The use of any non-Atari parts may also adversely affect the safety of your game and cause injury to yourself and others. Be very cautious in using non-Atari-supplied components with our games, in order to insure your safety.

Atari distributors are independent, being privately owned and operated. In their judgment they may sell parts or accessories other than Atari parts or accessories. Atari cannot be responsible for the quality, suitability or safety of any non-Atari part or any modification including labor which is performed by such distributor:

This document is and contains confidential trade secret information of Atari, Inc.

This document is loaned under confidential custody for the sole purpose of operation, maintenance or repair of Atari equipment and may not be used by or disclosed to any person for any other purpose whatever, and remains the property of Atari, Inc.

Neither it nor the information it contains may be reproduced, used, or disclosed to persons not having a need to know consistent with the purpose of the loan, without written consent of Atari, Inc. © © « « © © © BN

Page 85

ATARI, INC. 790 SYCAMORE DRIVE P.O. BOX 906 MILPITAS, CALIFORNIA 95035, 408/942-3100 © TELEX 35-7488

© + vere: conmuncatons comeany