CATHODE RAY TOMES

Undercover Cops

Undercover Cops (World) (Irem, 1992) · Manual · 13 pages · 27 sections · original scan

Page 1

IREM AMERICA CORPORATION

OWNERS MANUAL

Page 2

VIDEO GAME OPERATOR:

Don't Get Involved In A Federal Crime. Duu’t

Buy Or Operate Copy Or Unauthorized Boards In

Your Games.

Every operator who buys or

operates a counterfeit or unauthorized

(trmported or domestic) ts contributing to the end of our industry and committing a FEDERAL CRIME. New criminal laws have recently been enacted that provide for maximunt penalties of $250,000 or five years in prison or both, per offense. EACH GAME [S_A SEPARATE OFFENSE

Y rgd ~

RS If you have any information about any

unauthorized games in the United States, contact sour lacal FRI ar, (eserical Amusement Machine Association 205 The Strand Suite 3 Alexandria, Virginia 22314 (703) 548-8044 All information will be treated in confidence.

pep eT RE

Page 3

SAFETY

The following topics should be carefully studied to insure maximum reliability and safety for both serviceman and customer. Shock Hazard: The high voltage present on the monitor may he very dangerous. Extreme caution must be used when working with or around the monitors. Be certain that the grounding strap is attached to the monitor frame. The picture tube in the monitor is also a hazard and should be handied with care. Do not strike, scratch, or subject the tube to more than moderate pressure as it may implode causing serious injury from flying glass. Be certain that the control panel, power supply monitor, and coin door are all properly grounded to the ground wire inside the line cord. Do not remove ground prong off plua end.

PARTS LIST

1 - Control Panel Overlay 1 - FCC tahel 6 - LD. Tags 1 - Manual 12 - Buttons 1 - 3rd Player Cables 1 - Marquee Art 1 - Undercover Cops PCB

IREM AMERICA CORPORATION® 8434 154th Avenue NE Redmond, WA 98052 (206) 881-0900 FAX (206) 881-6503

FOR SERVICE CONTACT.

Your authorized Irem America Corporation® Distributor or SUMMIT SERVICE 2274 University Avenue St. Paul. MN 55114 (612) 645-9077

WARRANTY REPAIRS

Irem America Corporation PCB have a 90 day warranty from date of shipment. This includes all failures except those caused by the installer such as miswiring.

All PCB muet be returned by an authorized Iram America Corporation distributor. A Return Material Authorization must be obtained from Summit Service prior to returning material. A Purchase Order must also be given to Summit Service at this time. The package must be clearly marked with the RMA number.

Page 4

UNDERCOVER COPS is protected by federal copyright laws and is the property of lrem Anietica Curporation®. Any unauthorized versiono of thie gamo aro illegal by federal law. AAMA protected stickers must be attached to the PCB. Please notify Irem America Corporation of any boards not having the AAMA seal.

IMPORTANT F.C.C. WARNING

THIS EQUIPMENT COMPLIES WITH THE REQUIREMENTS IN PART 15 OF FCC RULES FOR A CLASS A COMPUTING DEVICE. OPERATION OF THIS EQUIPMENT IN A RESIDENTIAL AREA MAY CAUSE UNACCEPTABLE INTERFERENCE OF RADIO AND TV RECEPTION REQUIRING THE OPERATOR TO TAKE WHATEVER STEPS ARE NECESSARY TO CORRECT THE INTERFERENCE. YOUR FCC COMPLIANCE LABEL IS ENCLOSED IN YOUR KIT AND MUST BE ATTACHED TO YOUR GAME PRIOR TO PLACING ON LOCATION. THIS LABEL INDICATES YOUR GAME WAS DESIGNED TO MEET FCC STANDARDS 47CFR15.19. WE ADVISE USING STAPLES IF NECESSARY TO MAKE SURE THE LABEL STAYS ON.

DANGER

The isolation traneformer must be used with the monitor and power supply

This game must be equipped with a three wire 110 volt plug for safety. Under no circumstance remove the ground plug. :

This game is designed with a JAMMA 56 pin connector. This piug is one of the finest operator friendly features in our industry today. What this means to you is that:

  • 1, 2,A,B, 27, 28, e and f are grounded
  • 3.4.C and D are +5 volts
  • 5 and E are -5 volts
  • 6 and F are +12 volts Also, all video and joystick functions are always in the same place. Once a cabinet is wired tor JAMMA, it is easily changed from game to game.

Many older games such as Pac Man®, etc., have the power supply on the board. This will not worklll Only a JAMMA connector with proper voltage will work irem America Corporation® recommends using an 11 or 15 amp switching power supply with Undercover Cops®.

MONITORS

Undercover Cops® is designed to be operated with a horizontal raster scan monitor with negative sync (RGB). This means Undercover Cops® will not work with any X-¥ (Tempest, Space Dual, Star Trec}, etc. An isolation transformer must be used in conjunction with the monitor. This is for your safety. The monitor also utilizes extremely high voltages. The monitor inay alsv retain a charge for an extended period of time. Safety goggloe muct bo worn while removing or replacing the monitor.

It is highly recammended that the monitor is verified good before the new Undercover Cops® kit is installed in your new and or rebuilt cabinet.

Page 5

INSTALLATION OF KIT

IN USED CABINET

To Disassemble:

+. Open back door and remove old board set and power supply, if you are using a new switching power supply.

9 Remove marquee giass and monitor glass.

  • Remove control panel and set aside.

4, Remove old wire narness, leaving 110 voll witiny irlaut. Alsu, leave the grounding atrape to the monitor, coin door, control panel, and power supply intact.

Installation:

  • Mount the board set on the side panel of the cabinet as close to the middie of the game as possible (approximately 10-12” off bottom).
NOTE; Do not mount board directly below control or any vents or cracks so that liquide may seep on to the board. Do not forget about coins that may drop on to the board. Also, mount the board with edge connector facing up.
  • Mount the power supply on the bottom of the cabinet with connectors facing the rear of the cabinet. An optional mounting might be on the side panel just below the board set, connector to rear.
  • If the game does not have an isolation transformer, you must protect your customers and your game. Install one between the 110 voit fine and your monitor/power supply.

4, Place the provided JAMMA wiring harness on the board. Connect the +5, +12, -5, and ground wires to the corresponding lugs on the power supply, connecting all the wires. If you don't, you will probably burn the board connector.

5, Runa wire from +12 volts to the coin door lights. Run a wire from +12 volts to the coin counters. This completes the power requirements.

  • Connect the Audio (+) and Audio (-) to the speaker.
  • Cornect the video red, green, blue, ground, and syne to the corresponding wires on the monitor. If the monitor is not a negative composite sync, see sync modifications chart.
  • Cut the marquee to size. Replace the marquee lamp, if needed. Install the marquee panel.
  • Connect the coin 1 and coin 2 wires to the coin switches. Connect the coin counter 1 and coin counter 2 wires to the coin counters.
NOTE: If you only have one coin counter, see coin counter diagram. It will not matter if the coin counters are only rated at 6 volts, as the pulse is not long enough to burn out the counter.

eRe REA

Page 6
  • Disassemble the control panel of all the hardware. Do not remove the old panel overlay. Determine where to place the new joystick and buttons if they must be repositioned. Then, cut new holes.
NOTE: If you are going to use plexiglass over the contro! panel, we suggest that you use a good 1%" polycarbonate with a scratch resistant coating. We recommend GENERAL ELECTRIC LEXAN MRS with margard or TUFFAK CM-2. These do not crack or break with . abuse.

Cut and drill plex as needed. Remove the old control panel overiay carefully and apply the new overlay on top of the old glue. Use an Exacto knife to cut out any button or bolt holes. Apply necessary decals over appropriate buttons. Now assemble the contro! panel.

  • #olt the control panei to the cabinet. Now connect the appropriate wires to the correct switches. Connect the 1 player and 2 player start wires.

12, Be oure to inotall tho FCC cage to avoid unnecessary radio frequency interference.

  • Power up the game. Look over your installation for errors, and then apply power, listening for unusual sounds. Check for smoke or sparks. If everything is okay, wire tie all wires to form a nice, neat wiring harness. Clean the cabinet inside and out. Measure the +5 volts on the furthest point from the edge connector and adjust 5 volts to 5.05 volts. Use a tinted plex over the monitor if there are burns in the screen. We suggest bronze or grey tinted plex. Touch up the cabinet with [rest pairil, and then repair all cabinet dents or chips, using an auto body product called Duraglass. This is similar to bondo. You can consult your local auto body shop or auto parts supplier for this product, as well as advice on how to use it.
  • Be sure your ground plug is good. All metal exposed to the player must be grounded (coin door, control panel, etc.) including all metal inside exposed.

UNDERCOVER COPS®

lrem America Corporation recommends installing your new UNDERCOVER COPS kit in only a new or refurbished cabinet. Instailing UNDERCOVER COPS in an older cabinet will result in lower earnings. The cabinet should be as follows:

  • horizontal monitor ~
  • 11 amp or larger power supply
  • monitor not laying down flat. @ START BUTTON CABINET TYPE O ATTACK BUTTON
TABLE TYPE2P UPRIGHT3P UPRIGHT3P UPRIGHT

Too foo Too | Too Too Too Oa 70 Too Too TOO LU

SET DIP SW2-3 OFFSET DIP SW2-3 OFFSFT DIP SW?.3 ONSET DIP SW2-3 OFF|
SET SW1-6 ONSET SW14 ONGN5-6 HAS TO BECN5-6 HAS TO BE

CONNECTED WITH CONNECTED WITH 3P COIN SW 3P START SW.

SET SW1-6 OFF SET SW1-6 ON

Page 7
  • Hye Contros:

SPRING ACTION JOYSTICK

‘ Featuring G. © Nylon and solid stee! construction

‘= Spring ‘eturn to center

Micro a leat switches

individually replaceable

Long statt, 1.5 inch

iamete red knob fitted

as standard —— Harr Controis

Prone: (

Fax: (312) 5936137 Telex: 297249 CONTROL UR SUPER JOYSTICK » Unique hardle design

  • Spring retum to center
  • Rugged acuator for fong tite » Change acuation to deway or B-nay simply ty flipping sctuator over sovensovmTien_eikeoe oa SOE0EL50 Siar pick any Oey coe | sosoes.c0 sip yen ey
Page 8

1.

FIG. Monitor Syne it your monitor does not have dual polarity positions for sync, you may use on of the following

methode to get your game gaing CURE 1: Install a simple one \.C. Circuit on your logic board. This |.C. may be “piggy backed” on to another 7404 series chip for power by bending up al! but the two power pins so that they are parallel to the top surtace of the new |.C. and then connecting the power pins only to the existing chip. (See Fig. 1) Next connect the sync wires as shown in Fig. 2. (Note: Figure 2 shows a hookup

for either composite or separate syncs.)

HORIZONTAL SYNC INPUT FROM P.C.B. +5VDC COR COMPOSITE SYNC INPUT > 7 HORTZONTAL_SYNC OUTPUT TO MONITOR NC. CUR COMPOSITE SvNe CUTPUT?

74LS04 VERTICAL SYNC INPUT FROM P.C.B. NC.

VERTTCAl SYNC GLITPUT TO MONITOR NC. 74L504

Nc. NC.

Nee Ne.

1 GROUND NC.

BENT PINS

FIG. 2

SOLDE!

GURE 2: Used for Wells-Gardner Video-Sync boards with positive syne cannectinns only. (Vertical

mount board 85x14 OB.)

Cut the traces on the solder side of the board between input pins 5 & 6 to the unbanded (anode) ends of diodes X201 & X202. Add MPSA 56 transistor as follows: Collector to anade leads of diodes X201 & X202. Base pins 5 & 6 of the video input connector. Emitter to cathode (banded) lead of zener diode 2L201. Insert a 1N4148 diode - cathode to the emitter of the MPSA56 and anode to the base. (See Fig. 3)

RED

GREEN 1N4 148 z MPSASG BLUE 3

GND 4

VERT. 5

HORZ. 6

SUT BOTH TRACES ee

Page 9
  • Horizontal Tearing CAUSE: The negative sync signal of most logic sets are slightly different than the GO7-CBO monitor negative sync inputs. The result of this mismatch is a horizontal “wave” or “curl”. CURE 1: On the monitor deflection board, replace C303 with a 10uf 25V radial iead capacitor with the positive lead towards the collector of X305. (CAUTION: be sure to check this step as the original cap is not polarized.) Then replace C501 with the cap removed from the €303 location.

CURE 2: Connect 1N4148 fast-switching diodes across both the positive and negative sync inputs to the monitor. (See Fig. 4) NOI: Both diodes must be installed or you will not have vertical stability. iN4148

NEGATIVE SYNC INPUT ‘

  • HORZ. - VERT. GND

FIG. 4

+ HORZ- + VERT. = GNU BLUE GREEN RED

CURE 3: Join negative sync inputs J2 and J3 together with a jumper. Locate W102 and install a jumper from W102 to either J2 or J3.

CURE 4: For Wells-Gardner K4600 series monitors. Replace C356 (4 7uf 25V) on the Horizontal /vertical board (vertically mounted hoard nearest the flyback transformer) and center the horizontal hold pot. Turn L351 for the best horizontal stability and fine-tune with the horizontal width pot.

COIN COUNTER DIAGRAM

If only one coin counter is to be used Install two diodes tn the tollowing manner:

waz vou

Amaoo. COIN COUNTER 1

COIN COUNTER Sern counter £

NOTE: IF DIODE INSIDE COIN COUNTER ANa001 IS NOT PRESENT, INSTALL ON!
Page 10

UNDERCOVER COPS

DIP SWITCH SETTINGS

DIP SWITCH 1 at SWITCH NUMBER gpa ps Te Tar Te FUNCTION

NUMBER OF WARRIORS:

[prFFroury a a START BUTTONS Tes

TEST MODE TEST

START BUTTONS: THIS FEATURE IS USED IN CONJUNCTION WITH DIP SWITCH 3-3, TO ALLOW THE ATTACK BUTTONS TO START THE GAME PLAY. THIS ALLOWS THE USE OF INDIVIDUAL COIN CHUTES ON THREE PLAYER PANELS.

THOT MODE: TURN WITCH #8 ON, DEPRESS BOTH ATTACK & JUMP BUTTONS AT THE SAME TIME. EXIT THE TEST MODE BY DEPRESSING BOTH THE ATTACK & JUMP BUTTONS TOGETHER A SECOND TIME.

DIP SWITCH SETTINGS

DIP SWITCH 2 FUNCTION SWITCH NUMBER Tp2ztT3T4@) ste tz ts INVERT Orr SCREEN on NUMBER OF oF PLAYERS on COIN CHUTES OFF oF

[COIN MODE 1aaBd
or | on[ore | ore}or

ort orn | on “| ore | or

1 coCeeC
5 ODN / 1 Playont | ort | oF[|or

ed

1 core 72 PLATor | err | on]ow | or

[recom ps part a Toon) + mus or | ore | or | on | on 1 coit 7 5 Par ee

2 com 7 6 PLATon | "or | on[or]or
Foon 73 Putort[oe | on | on]on
‘3 COIN f 2 PLAY“oreorridon“on
Tom 73 Fara [ ao | ot]on
CORTEAUE coreon | ere | a8]ona
FREE PLATcoreaea
‘2 COIN 7 1 PLAYomOrrOFFa |
7 eo 71 FATaOT
3 come 77 PLATon]on
3 conn 74 Puaon[oron.
COIN MODE 2B1 COI / 2 PLAYonoo]or
7 cotN 7 3 PLATaroar
760m 7 5 PLATafon
2 COTW | 6 PLAYon_=]om

CONTINUE COIN: THIS MODE WILL USE TWO COINS TO START A GAME AND ONE COIN TO CONTINUE. IF TWO PLAYERS ARE GOING TO PLAY FOUR COINS ARE REQUIRED TO START AND 2 COINS TO CONTINUE. THIS MODE MAY NOT BE SELECTED WITH ANY OTHER COIN MODE.

Page 11

JAMMA CONNECTOR UNDERCOVER COPS

COMPONENT SIDEPosPosSOLDER SIDE

FUNCTION iz FUNCTION GROUND Lt A GROUND

GROUND2BGROUND
+5 VOLTS3Cc+5 VOLTS
+5 VOLTS4D+5 VOLTS
[=5 VOLTS5E-5 VOLTS
+12 VOLTS&¥+12 VOLTS
PREVENT KEY7HPREVENT KEY
COIN COUNTER #18oCOIN COUNTER #2
GROUND9KGROUND
AUDIO POS +10LAUDIO NEG —

ai M

VIDEO RED12NnVIDEO GREEN
VIDEO BLUE13PVIDEO SYNC*
VIDEO GROUND14RSERVICE SWITCH
TEST SWITCH158
COIN INPUT 1istCOIN INPUT 2
START 117USTART 2
1P UP18Vv2P UP
1P DOWN19W2P DOWN|
1P LEFT20x2P LEFT
1P RIGHT21Y2P RIGHT
1P ATTACK22b42P ATTACK
IP JUMP23a2P JUMP

24 b 25 ¢ | : 26 a

GROUND27eGROUND

GROUND 28 Fa GROUND

3RD PLAYER CONNECTIONS

CNS FUNCTION WHEN DIP SWITCH 2-3 IS OFF, CNS-6 GROUND HAS TO BE CONNECTED TO THE 3P START 3P_ RIGHT SWITCH. WHEN DIP SWITCH 2-3 IS ON, 3P LEFT CN5-6 HAS TO BE CONNECTED TO THR 2P 3P_ DOWN COIN SWITCH. 3P UP {3P START/COIN 3P_ JUMP "| Wf 0] ~ja]upe/)rmtHlo (7)

3P_ATTACK

Page 12

ISOLATION

3 AMP VARISTOR TRANSFORMER

SLO-BLO SWETCH EMI FILTER

110 VAC FUSE ON/OFF cORCOM 11 AMP SROUND

110 vac | SWITCHING +S ype

POWER SUPFLY

-S VDC +12 VDC

COUNTER #2

COUNTER #1

& OHM SPEAKER

L AUTO + AUDIO — RGB COLOR MONET OR HORIZONTAL,

VIDEO RED N VIDEO GREEN 13 VIDEO BLUE NEG C4P. SYNC VIDEO GROUND GROUND = COIN DOOR fal LIGHTS #94 BULBS 1ST PLAYER CONTROLS SHOWN

COIN SWITCHES

COIN INPUT #1 COIN INPUT #2 CAP2C2P> 17 1> START F u 22 START ' PB 21 Y RIGHT i A 200 X LEFT

19° WH DOWN Tt I Dj 18 Yo UF al O RI wl ATTACK 22 Z artack T| QI TI NPI SUMP” 23 a JINP a

N

27,28,e,f GROUND > al

al

UNDERCOVER COPS FoR SRO PLAYER.

Page 13

ba & : PLAYERS ed MOTE! SPECIAL START/COIN OPTIONS

GI

SET DIP SWITCHES AS FOLLOFS: hy

D

3 PLAYER GAME WITH

SEPARATE COIN CHUTES

NO START BUTTONS DIP SW 1-6 = OFF DIP SW 2-3 = ON

COMMON COIN CHUTES

AND START BUTTONS

DIP SW 1-6 = ON DIP SH 2-3 = OFF 125456789

PLEYERL

2 PLAYER GAPE WITH COMMON COIN CHUTES. AND START BLTTONS. DIP SW 1-6 = ON DIP SW 2-3 = OFF 2 PLAYER TAELE GAME WITH JAMMA CONNESTOR

AND START BUTTONS COMPONENT S:DE DIP EW 1-6 = ON L 9 DIP W 2-3 = OFF cNS

SRE PLAYER

UNDERCOVER COPS