CATHODE RAY TOMES

Lost World

The Lost World: Jurassic Park (pinball, CPU 2.02, display A2.01) (Sega, 1997) · Manual · 95 pages · 68 sections · original scan

Page 1

1ST PRINTING - JL

THE (ost WORLD

JURASSIC Laid RS

U/R TYPE

OWNER’S MANUAL

® Before using this product, read this OWNER'S MANUAL carefully to understand the conte erein stated.

  • After reading this manual, be sure to keep it available nearby the

IMPORTANT! product or elsewhere convenient for referring to it anytime when

: necessary SEGA ENTERPRISES, LTD.

MANUAL NO. 420 - 6325 -

Page 2

THE LOST WORLD: JURASSIC PARK TM & © 1997 Universal City Studios, Inc. and Amblin Entertainment, Inc. All Rights Reserved. Licensed by MCA/Universal Merchandising, Inc.

Page 3

BEFORE USING THE PRODUCT, se sure to pean THE FOLLOWING:

To maintain the safety: To ensure the safe usage of the product, be sure to read the following before using the product. The following instructions are intended for the users, operators and the personnel in charge of the operation of the product. After carefully reading and sufficiently understanding the warning displays and cautions, handle the product appropriately. Be sure to keep this manual nearby the product or elsewhere convenient for referring to it when necessary. Herein, explanations which require special attention are enclosed with dual lines. Depending on the potentially hazardous degrees, the terms of DANGER!, WARNING!, CAUTION!, etc. are used. Be sure to understand the contents of the displays before reading the text. Indicates that mishandling the Indicates that mishandling the product by disregarding this picto- product by disregarding this caugraph will cause severe injury or tion will cause a slight hazardous death. situation which can result in per-

DANGER! CAUTION! sonal injury and or material damage.

Indicates that mishandling the Indicates that mishandling the product by disregarding this warn- product by disregarding this dising will cause a potentially hazard- play can cause the product's intrinjus situation which can result in sic performance not to be obtained, WARHING! death or serious injury. IMPORTANT! resulting in malfunctioning.

For the safe usage of the product, the following pictographs are used: Indicates "HANDLE WITH CARE." In order to protect the human body and equipment, this display is attached to places where the Owner's Manual and or Service Manual should be referred to.

Indicates a "Protective Earth Terminal." Before operating the equipment, be sure to connect it to the Ground.

O Perform work in accordance with the instructions herein stated. Instructions for work-are explained by paying attention to the aspect of accident prevention. Failing to perform work as per the instructions can cause accidents. In the case where only those who have technical expertise should perform the work to avoid hazardous situation, the instructions herein state that the serviceman should perform such work. O Be sure to turn off power before working on the machine. To prevent electric shock, be sure to turn off power before starting the work in which the worker touches the interior of the product. If the work is to be performed in the power-on status, the Instruction Manual herein always states to that effect. O Be sure to ground the Earth Terminal (this, however, is not required in the case where a power cord with earth is used). This product is equipped with the Earth Terminal. When installing the product, Connect the Earth Terminal to the "accurately grounded indoor earth terminal" by using an earth wire. Unless the product is grounded appropriately, the user can be subject to electric shock. After performing repair, etc. for the Control equipment, ensure that the Earth Wire is firmly connected to the Control equipment. O Ensure that the Power Supply used is equipped with an Earth Leakage Breaker. This product does not incorporate the Earth Leakage Breaker. Using a power supply which is not equipped with the Earth Leakage Breaker can cause a fire when earth leakage occurs. O Be sure to use fuses which meet the specified rating. (only for the machines which use fuses). Using fuses exceeding the specified rating can cause a fire and electric shock.

Page 4

O Specification changes (removal of equipment, conversion and addition) not designated by SEGA are not allowed. The parts of the product include warning labels for safety, covers for personal protection, etc. It is very hazardous to operate the product by removing parts and or modifying the circuits. Should doors, lids and protective parts be damaged or lost, refrain from operating the product, and contact where the product was purchased from or the office herein stated. O Ensure that the product meets the requirements of appropriate Electrical Specifications. Before installing the product, check for Electrical Specifications. SEGA products have a nameplate on which Electrical Specifications are described. Ensure that the product is compatible with the power supply voltage and frequency requirements of the location. Using any Electrical Specifications different from the designated Specifications can cause a fire and electric shock. O Install and operate the shar in places where appropriate lighting is available, allowing warning labels to be clearly read. To ensure safety for the customers, labels and printed instructions describing potentially hazardous situation are applied to places where accidents can be caused. Ensure that where the product is operated has sufficient lighting allowing the warnings to be read. If any label is peeled off, apply it again immediately. Please place an order with where the product was purchased from or the office herein stated. fe) bakit i the Monitor, be very careful. (Applies only to the product w/ monitor). Some of the monitor (TV) parts are subject to high tension voltage. Even after turning off power, some portions are still subject to high tension voltage sometimes. Monitor repair and replacement should be performed only by those technical personnel who have knowledge of electricity and technical expertise. O When transporting or reselling this product, be sure to attach this manual to the product.

In the case where commercially available monitors and printers are used in this product, only the contents relating to this product are explained herein. Some commercially available equipment has functions and reactions not stated in this manual. Read this manual together with the specific Instruction Manual of such equipment. + Descriptions herein contained may be subject to improvement changes without notice.

  • The contents described herein are fully prepared with due care. However, should any question arise or errors be found, please contact SEGA.

INSPECTIONS IMMEDIATELY AFTER TRANSPORTING THE PRODUCT TO THE LOCATION.

Normally, at the time of shipment, SEGA products are in a status allowing for usage immediately after transporting to the location. Nevertheless, an irregular situation may occur during transportation. Before turning on power, check the following points to ensure that the product has been transported in a satisfactory status. a a there any dented portions or defects (cuts, etc.) on the external surfaces of the cabinet? CJ Are Casters and Adjusters, damaged? GO Do the power supply voltage and frequency requirements meet with those of the location? 1 Are all wiring connectors correctly and securely connected? Unless connected in the correct direction, connector connections can not be made accurately. Do not insert connectors forcibly. (Do power cords have cuts and dents? C} Do the fuses used meet specified rating? Is the Circuit Protector in an energized status? © Are all accessories available? O Canall Doors and Lids be opened with the Accessory keys? Can Doors and Lids be firmly closed?

Page 5

oOo TABLE OF CONTENTS

BEFORE USING THE PRODUCT, BE SURE TO READ THE FOLLOWING: TABLE OF CONTENTS INTRODUCTION OF THE OWNER’ S MANUAL HANDLING PRECAUTIONS ... 0.0 .s cee cece cence cere e rece eeeeees 1~2 PRECAUTIONS CONCERNING INSTALLATION LOCATION...........04. 3~4 PRECAUTIONS TO BE HEEDED FOR OPERATION NAME OF PARTS ......eeeeeeeee eee eeeeeeeeeenee ACCESSORIES a ues ce cee tna ce ccna beee tienda nea ee ASSEMBLING AND PRECAUTIONS ...... eee eeeeeeee eet eee eee eennes PRECAUTIONS TO BE HEEDED WHEN MOVING THE MACHINE.......... 17 CONTENTS OF GAME 1... cece eee ete cent eter e eee t ene nee eeas EXPLANATION OF TEST AND DATA DISPLAY........ 9-1 POWER SUPPLY UNIT AND COIN METER 9-2 TEST MODE... . cece cece cece cece e nen e eee 9-3 MEMORY TEST 9-4 INPUT TEST........ 9-5 SOUND TEST........ 9-6 C.R.T. TEST 9-7 GAME ASSIGNMENTS ........ cece cece eee e eee tent eee ee ees 9-8 COIN ASSIGNMENTS... 0.0.0 cece cece e ete e cence eee eeeenes 9-9 GUN SETTING 9-10 OUTPUT TEST 9-11 BOOKKEEPING 9-12 BACKUP DATA CLEAR. ..... ccc cece cece erence erent eneeaee

  • CONTROLLER (GUN) .....- 0. eee e cece eee cee eee tent eee t eens
  • COIN SELECTOR OONAARWNH>
  • MONITOR... cece cece e eee e eee e tent e eee e teenie een eesenee 12-1 CAUTIONS AND WARNINGS CONCERNING THE SAFETY FOR HANDLING THE MONITORS.......+0eeeeeee 44~45 12-2 CAUTIONS TO BE HEEDED WHEN CLEANING THE CRT SURFACES........2eeeeeeeeeeeees 12-3 ADJUSTMENT METHOD........0ceeeeeeeeeee
  • REPLACEMENT OF FLUORESCENT LAMP AND LAMPS... 13-1 FLUORESCENT LAMP REPLACEMENT..........65- 13-2 LAMP REPLACEMENT... 0.0. ccceseeeseeeeeenas
  • PERIODIC INSPECTION TABLE ..........ceeeeeuee
  • TROUBLESHOOTING ......eceeeee ee eeteeeeeneeeee
  • GAME BOARD... 2... ese e cece cece tena eee ee nena 16-1 REMOVING THE GAME BOARD.......0eceeeeeeeeeeeeeeeeeees 16-2 COMPOSITION OF GAME BOARD........eseseeeeeeeeeeceeees
  • DESIGN RELATED PARTS ........ccseceeeeneeeeeees
  • PARTS LIST ......ccee eee eeee
  • WIRE COLOR CODE TABLE
  • WIRING DIAGRAM..........008
Page 6

SPECIFICATIONS > 800 mm (W) X 1,230 mm (D) (31.5 in. X 48.4 in.) Installation space

Height : 2,160 mm (85.0 in.) Weight : Approx. 207 kg. (456.4 Ibs. ) Power, maximum current > 300W 3.30A (AC 110V 50 Hz AREA) 289W 3.30A (AC 110V 60 Hz AREA) 294W 3.00A (AC 120V 60 Hz AREA)

307W1.70A(AC 220V 50 Hz AREA)

299W 1.70A (AC 220V 60 Hz AREA)

306W1.60A(AC 230V 50 Hz AREA)
293W1.60A(AC 230V 60 Hz AREA)
300W1.50A(AC 240V 50 Hz AREA)

294W 1.50A (AC 240V 60 Hz AREA) For TAIWAN Power, current : 285W 3. 30A(MAX. ) 210W 2. 40A(MIN. ) MON! TOR : 29 INCH COLOR MONITOR

INTRODUCTION OF THE OWNER'S MANUAL

SEGA ENTERPRISES, LTD., supported by its high electronic technology of LSIs, microprocessors, etc. and a wealth of experience, has for more than 30 years been supplying various innovative and popular game machines to the world market. This Owner's Manual is intended to provide detailed descriptions together with all the necessary information covering the general operation of electronic assemblies, electromechanicals, servicing control, spare parts, etc. as regards THE LOST WORLD U/R TYPE, a new SEGA product . This manual is intended for those who have knowledge of electricity and technical expertise especially in ICs, CRTs, microprocessors, etc. Carefully read this manual to acquire sufficient knowledge before working on the machine. Should there be a malfunction, non-technical personnel should under no circumstances

touch the interior system. Should such a case arise, contact our Main Office or

the closest branch office listed as follows:

SEGA ENTERPRISES, INC. (U.S.A.)/CUSTOMER SERVICE 45133 Industrial Drive, Fremont, California 94538, U.S.A. Phone : (415) 802-3100 Fax : (415) 802-1754

Page 7

[ DEFINITION OF LOCATION MAINTENANCE MAN AND SERVICEMAN

A

WARNING!

Non-technical personnel who do not have technical knowledge and expertise should refrain from performing such work that this manual requires the location's maintenance man or a serviceman to carry out, or work which is not explained in this manual. Failing to comply with this instruction can cause a severe accident such as electric shock.

Ensure that parts replacement, servicing & inspections, and troubleshooting are performed by the location's maintenance man or the serviceman. It is instructed herein that particularly hazardous work should be performed by the serviceman who has technical expertise and knowledge.

The location's maintenance man and serviceman are herein defined as follows:

“Location's Maintenance Man" : Those who have experience in the maintenance of amusement equipment and vending machines, etc., and also participate in the servicing and control of the equipment through such routine work as equipment assembly and installation, servicing and inspections, replacement of units and consumables, etc. within the Amusement Facilities and or locations under the management of the Owner and Owner's Operators of the product.

Activities of Location's Maintenance Man : Assembly & installation, servicing & inspections, and replacement of units & consumables as regards amusement equipment, vending machines, etc.

Serviceman : Those who participate in the designing, manufacturing, inspections and maintenance service of the equipment at an amusement equipment manufacturer. Those who have technical expertise equivalent.to that of technical high school graduates as regards electricity, electronics and or mechanical engineering, and daily take part in the servicing & control and repair of amusement equipment.

Serviceman's Activities : Assembly & installation and repair & adjustments of electrical, electronic and mechanical parts of amusement equipment and vending machines.

Page 8
  • HANDLING PRECAUTIONS

A\

WARNING!

IMPORTANT!

When installing or inspecting the machine, be very careful of the following points and pay attention to ensure that the player can enjoy the game safely. Non-compliance with the following points or inappropriate handling running counter to the cautionary matters herein stated can cause personal injury or damage to the machine.

Before performing the work, be sure to turn power off. Performing the work without turning power off can cause an electric shock or short circuit. To avoid electric shock or short circuit, do not insert or pull out the plug quickly. To avoid electric shock, do not unplug with a wet hand. Do not expose Power Cords and Earth Wires on the surface, (floor, passage, etc.). If exposed, the Power Cords and Earth Wires are susceptible to damage. Damaged cords and wires can cause electric shock and short circuit accidents.

To avoid causing a fire or electric shock, do not put things on or damage

Power Cords. When or after installing the product, do not unnecessarily pull the power cord. If damaged, the power cord can cause a fire or electric shock. In case the power cord is damaged, ask for replacement through where the product was purchased from or the office herein stated. Using the cord as is damaged can cause fire, electric shock or leakage. Be sure to perform grounding appropriately. Inappropriate grounding can cause an electric shock. Be sure to use fuses meeting specified rating. Using fuses exceeding the specified rating can cause a fire or electric shock. The electronic parts on the IC Board could be damaged due to human body's static electricity. Before performing IC Board related work, be sure to discharge physically accumulated statics by touching grounded metallic surfaces.

To avoid causing a fire or electric shock, do not make Specification

changes by removing, converting and making additions unless otherwise designated by SEGA. Be sure to perform periodic maintenance inspections herein stated.

For the IC board circuit inspections, only the logic tester is allowed. The use of a multiple-purpose tester is not permitted, so be careful in this regard. When cleaning the CRT surfaces, use a soft, dry cloth. Do not apply chemicals such as thinner, benzine, etc. The electronic parts on the IC Board could be damaged due to human body's static electricity. Before performing IC Board related work, be sure to discharge physically accumulated statics by touching grounded metallic surfaces.

Page 9

CONCERNING THE STICKER DISPLAY CONCERNING WARNING DISPLAYS

SEGA product has Stickers describing the product manufacture No. (Serial No.) and Electrical Specifications. Also it has a Sticker describing where to contact for repair and for purchasing parts. When inquiring about or asking for repair, mention the Serial No. and Name of Machine indicated on the Sticker. The Serial No. indicates the product register. Identical machines could have different parts depending on the date of production. Also, improvements and modifications might have been made after the publication of this Manual. In order to meet the above situations, mention the Serial No. when contacting the applicable places.

440-WSO012XEG AAWARNING| za SEGA product has warning displays on Stickers, Labels and or printed instructions adhered / attached to or incorporated in the places where a potentially hazardous situation can arise. The warning displays are intended for avoiding hazardous situation relating to maintenance and servicing work, and for the prevention of accidents for the customers. There are some portions in the Cabinet, which are subject to high tension voltage, etc. where accidents can be caused only by touching. When performing the servicing work, be very careful of the warning displays. Especially, repair and replacement work not mentioned herein, should be performed by those technical personnel who have knowledge of electricity and technical expertise. For the prevention of accidents, caution any customer whose act runs counter to the warnings, as to the effect that he must stop the act.

He mule can + Do not use the for E: ee [AACAUTION [Bint te utegen tn ps Isbreakable | ‘avery carta when oplecing them 440-CSO109XEG

Electrical Specifications 440-WSO002XEG

AXDANGER

Da ret ooo he monitor 440-DSOO13XEG

Display /

440-HS0002XEG Serial No. Display /

Page 10
  • PRECAUTIONS CONCERNING INSTALLATION LOCATION

A

WARNING!

This product is an indoor game machine. Do not install it outside. Even indoors, avoid installing in places mentioned below so as not to cause a fire, electric shock, injury and or malfunctioning. @ Places subject to rain or water leakage, or places subject to high humidity in the proximity of an indoor swimming pool and or shower, etc. Places subject to direct sunlight, or places subject to high temperatures in the proximity of heating units, etc. Places filled with inflammable gas or vicinity of highly inflammable/ volatile chemicals or hazardous matter. Dusty places. Sloped surfaces Places subject to any type of violent impact. Vicinity of anti-disaster facilities such as fire exits and fire extinguishers. The operating (ambient) temperature range is from 5°C to 40°C. Only in the case a projector is employed, the temperature range is from 5 to 30°C.

LIMITATIONS OF USAGE REQUIREMENTS

AN

@ Be sure to check the Electrical Specifications. Ensure that this product is compatible with the location's power supply, voltage and frequency requirements. A plate describing Electrical Specifications is attached to the product.

Non-compliance with the Electric Specifications can cause a fire and

electric shock. This product requires the Breaker and Earth Mechanisms as part of the location facilities. Using them in a manner not independent can cause a fire and electric shock. Ensure that the indoor wiring for the power supply is rated at 7A or higher (AC 100V~120V area) and 3A or higher (AC 220~240V area).

Non-compliance with the Electrical Specifications can cause a fire and

electric shock. Be sure to independently use the power supply equipped with the Earth Leakage Breaker. Using a power supply without the Earth Leakage Breaker can cause an outbreak of fire when earth leakage occurs. Putting many loads on one electrical outlet can cause generation of heat and a fire resulting from overload. When using an extension cord, ensure that the cord is rated at 7A or higher (AC 100~120V area) and 3A or higher (AC 220V~240V area).

Using a cord rated lower than the specified rating can cause a fire and

electric shock.

Page 11

@ Note that for transporting the machine into the location's building, the minimum necessary dimensions of the opening (of doors, etc.) are 0.9m

IMPORTANT! (W) and 2.0m(H). @ For the operation of this machine, secure a minimum area of 1.3m (W)x 1.6m (D). For ventilation, provide an approximately 10cm. space between the rear part of the cabinet and the wall.

SN Approx. 10 cm.

Ss

S

AG SS Yi yyy ‘ SS \N\ * N

FIG. 2

Page 12
  • PRECAUTIONS TO BE HEEDED FOR OPERATION

For the safe operation of the product, be sure to comply with the following precautions.

BEFORE STARTING OPERATION

mn In order to avoid accidents, check the following before starting the operation: @ Check if all of the adjusters are in contact with the surface. If they are

WARNING! not, the Cabinet can move and cause an accident.

Ensure that all of the Adjusters are in contact with the floor.

Do not put any heavy item on this product. Placing any heavy item on the product can cause a falling down accident or parts damage. Do not climb on the product. Climbing on the product can cause falling down accidents. To check the top portion of the product, use a step. To avoid electric shock accidents, check to see if door & cover parts are damaged or omitted. To avoid electric shock, short circuit and or parts damage, do not put the following items on or in the periphery of the product. Flower vases, flower pots, cups, water tanks, cosmetics, and receptacles/containers/vessels containing chemicals and water.

A To avoid injury, be sure to provide sufficient space by considering the

potentially crowded situation at the installation location. Insufficient

CAUTION! installation space can cause the player to come into contact with or hit the others and result in injury or trouble.
Page 13

| PAYING ATTENTION TO CUSTOMERS _|

A

WARNING!

A

CAUTION!

To avoid injury and trouble, be sure to constantly give careful attention to the behavior and manner of the visitors and players.

To avoid electric shock and short circuit accidents, do not allow customers to put hands and fingers or extraneous matter in the openings of the product or small openings in or around the doors. To avoid falling down and injury resulting from falling down, immediately stop the customer's leaning against or climbing on the product, etc. To avoid electric shock and short circuit accidents, do not allow the customers to unplug the power plug without a justifiable reason. To avoid injury resulting from falling down, and electric shock accidents due to spilled drinks, instruct the player not to place heavy items or drinks on the product.

Immediately stop such violent acts as hitting and kicking the product. Such violent acts can cause parts damage or falling down, resulting in injury due to fragments and falling down.

Page 14
  • NAME OF PARTS

BILLBOARD PLATE

FRONT DOOR ie Shield Case and AC Unit are located inside.

FIG. 4

Page 15
  • ACCESSORIES When transporting the machine, make sure that the following parts are supplied.

TABLE 5 ACCESSORIES

DESCRIPTION Part No. (Qty. )

Note OWNERS MANUAL 420-6325-03 (1)

Figures If Part No. has no description, the Number has not been registered or can not be registered. Such a part may not be obtainable even if the customer desires to purchase it. Therefore, ensure that the part is in safekeeping with you. KEY MASTER KEY 220-5576 (2) (2) For opening/closing For the CASHBOX DOOR the doors

TAMPERPROOF WRENCH M4 540-0006-01 (1) M5 540-0007-01 (1) TOOL SW MICRO TYPE 509-5080 (1) For spare, refer to Section 10.

LAMP WEDGE BASE 390-5160(1) For spare, refer to Section 13. FUSE 5000mA 125V 514-5036-5000 (1) For spare, refer to Section 15.

POWER CORD 600-6724 po0-6729 (1) For AC 110V AREA

600-6618 (1) For AC 220V~240V AREA Used for installation, see [3], Sec. 6).

Page 16

CARTON BOX GLASS CLEANER 601-8928 (1) 090-0174 (1) Used for transporting Used tor cleaning the Game Board. the Front Glass and Refer to the following. Mirror.

SZ

HOW TO USE THE CARTON BOX

‘S) @ When asking for the replacement or repair of the product's Game

Board (MODEL 3 BOARD), be sure to put the Game Board together

IMPORTANT! with the Shield Case in the Carton Box. Otherwise, the request is not acceptable. Put the Shield Case in the Carton Box by paying attention to the correct direction as per the following instructions and as shown by the instructions printed on the Carton Box. Handling in an erroneous manner can damage the Game Board.

"CHECK SIDE” Displa

FILTER BOARD

Wrap the Shield Case with the packing material and put it in the Carton Box as shown. Putting it upside down or packing otherwise in the manner not shown can damage the Game Board and parts.

Page 17
  • ASSEMBLING AND PRECAUTIONS

mn @ Perform the assembly work by following the procedure herein stated. Failing to comply with the instructions can cause an electric shock

WARNING! accident. @ Assembling should be performed as per this manual. Since this is a complex machine, erroneous assembling can damage the machine or cause the machine not to function as per specified performance. When assembling, be sure to perform the work by plural persons. Depending on the assembly work, there are some cases in which performing the work by a single person can cause personal injury or parts damage. Ensure that connectors are accurately connected. Incomplete connections can cause electric shock and short circuit accidents.

The installation and assembling work of this product is performed sequentially in order of the following 4 items:

INSTALLING THE BILLBOARD PLATE AND POP PANEL.

SECURING TO THE INSTALLATION LOCATION (ADJUSTER ADJUSTMENT)

POWER SUPPLY, AND EARTH CONNECTION

ASSEMBLING CHECK

Note that the tools such as a Phillips type screwdriver and wrench for hexagon bolt with 24 mm width across flats are necessary for the assembly work.
  • 1”) Phillips type screwdriver

24mm

ADJUSTABLE WRENCH (for M16 hexagon bolt)

Page 18

INSTALLING THE BILLBOARD PLATE AND POP PANEL

To perform work safely and securely, be sure to prepare a step which is in

a secure and stable condition. Using an unstable step can cause a violent

CAUTION! falling down accidents.

@ Take out the 3 Truss screws from the lower part of the Billboard and pull out the Billboard Case towards you. POP PANEL

@ Adhere the Pop Panel to the Billboard Case with 2-sided adhesive tape. 2-SIDED ADHESIVE TAPE

@) Return the Billboard Case to the original position and secure with the 3 truss screws.

@ Take out the 4 truss screws to remove Lamp Cover B.

©) Insert the Billboard Plate to the Billboard Case and secure Lamp Cover B with the 4 truss screws. TRUSS SCREW (3) M4 x 20, black, flat washer used.

FIG. 6.1la

t TRUSS _SCREW_(4) LA MX 12, black, 1 flat washer used. > LAMP COVER B BILLBOARD PLATE

PREPARE A STEP TO PERFORM WORK.

FIG. 6. 1b

Page 19

SECURING TO THE INSTALLATION LOCATION (ADJUSTER ADJUSTMENT)

A\ Make sure that all of the adjusters are in contact with the floor. If they are cmon ||" e cabinet may move causing én accident.

This machine has 4 casters and 4 adjusters (FIG. 6. 2 a). When the installation position is determined, cause the leg adjusters to come into contact with the floor directly, make adjustments in a manner so that the casters will be raised approximately 5mm. from the floor and make sure that the machine position is level.

@ Move the machine to the installation position.

@ Have all of the Adjusters make contact with the floor surfaces. Adjust the height of the Adjusters by using a wrench in the manner so that the machine position is kept level.

@® After making adjustments, fasten the adjuster nut upward and secure the height of the adjuster.

nut_upward. Fasten the Approx. 5 mm

FIG. 6.2b Having the Adjusters make contact with the floor surfaces

Approx. 10 cm

FIG. 6.2¢ : Refer to this Fig. (Scale: 1/100) for the layout of the place of installation. FIG. 6.24 Provide sufficient space so as to allow for ventilation by the ventilation fan.

Page 20

POWER SUPPLY, AND EARTH CONNECTION

A

WARNING!

Be sure to independently use the power supply socket outlet equipped with an Earth Leakage Breaker. Using a power supply without an Earth Leakage Breaker can cause a fire when the leakage occurs. Ensure that the "accurately grounded indoor earth terminal" and the earth wire cable are available (except in the case where a power cord plug with earth is used). This product is equipped with the earth terminal. Connect the earth terminal and the indoor earth terminal with the prepared cable. If the grounding work is not performed appropriately, customers can be subjected to an electric shock, and the product's functioning may not be stable. Ensure that the power cord and earth wire are not exposed on the surface (passage, etc.). If exposed, they can be caught and are susceptible to damage. If damaged, the cord and wire can cause an electric shock and short circuit accidents. Ensure that the wiring position is not in the customer's passage way or the wiring has protective covering.

Ensure that the Main SW is OFF.

= [| >

Turn the Main SW OFF.

Connect one end of the earth wire to the AC Unit earth terminal, and the other end to the indoor earth terminal. The AC Unit earth terminal has a Bolt and Nut combination. Take off the Nut, pass the earth wire through the Bolt, and fasten the Nut. The AC unit is mounted on the rear of Cabinet. The AC Unit incorporates the Main SW, Circuit Protector, Earth Terminal and Inlet which connects the Power Cord. Firmly insert the Power Plug into the Plug Socket and the other side of the plug to the Inlet. Turn the Main SW ON to turn power ON.

EARTH TERMINAL

aa,

MAIN SW

CIRCUIT PROTECTOR

INLET.

FIG. 6.34

Page 21

@® Firmly insert the power plug into the plug socket and inlet.

FIG. 6.3¢

@® Perform wiring for the Power Cord and Earth Wire. Install protective covering for the Power Cord and Earth Wire.

® Tur the Main SW ON to tum power ON.

Wiring Cover

FIG. 6.3d Wiring for Power Cord and Earth Wire

Page 22

ASSEMBLING CHECK

In the TEST MODE, ensure that the assembly has been made correctly and IC BD is satisfactory (refer to Section 9). In the test mode, perform the following test:

MEMORY TEST Selecting the MEMORY TEST on the test mode menu screen causes the on-board memory to be tested automatically. The game board is satisfactory if the display beside each IC No. shows GOOD.

PRESS TEST BUTTON TO EXIT

INPUT TEST aoe PoE? Selecting the INPUT TEST on the test mode aan an on menu screen causes the screen (on which each COIN CHUTE on switch is tested) to be displayed. Press each off switch. For the coin switch test, insert a coin from the coin inlet with the coin chute door being open. If the display beside each switch indicates "ON," the switch and wiring connections are satisfactory.

PRESS TEST BUTTON TO EXIT

SOUND TEST In the TEST mode, selecting SOUND TEST

career causes the screen, on which sound related BD and

Sear wiring connections are tested, to be displayed. Be sure to check if the sound is satisfactorily emitted from each speaker and the sound volume is appropriate.

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON

Page 23

CRT TESTIN2 In the TEST mode menu, selecting C.R.T. TEST allows the screen (on which the monitor is tested) to be displayed. Although the monitor adjustments have been made at the time of shipment from the factory, color deviation, etc., may occur due to the effect

caused by geomagnetism, the location building's steel

frames and other game machines in the periphery. By watching the test mode screen, make judgment as to whether an adjustment is needed. If it is necessary, adjust the monitor by referring to Section 12. In case of color deviation due to the monitor's magne- PRESS TEST BUTTON TS:CONTINUE tization, use DEMAG SW (see Section 9).

On the menu screen in the test mode, selecting GUN SETTING displays the screen on which gun sightsightXpos sigmxpos ing is set. Check to see if there is any problem for sight pos. sightYpos playing game. screenXpos sereenX pos sereenY pos sereenYpos

[OUT OF $PREEN 1P]

CURSOR (Impact Position) IMPACT MARK

CURSOR for 1P is blue and for 2P, red.

SIGHTING CHECK

PUT TEST commons Select "OUTPUT TEST" from the Test Menu in the

PLAYER | Test Mode to have the Lamp Test Screen displayed. PLAYER 2 Check if each lamp lights up satisfactorily. ROOM LIGHT > MARS LIGHT EXIT

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON

Perform the above inspections also at the time of monthly inspection.

Page 24
  • PRECAUTIONS TO BE HEEDED WHEN MOVING THE MACHINE

mn When moving the machine, be sure to pull out the plug from the power

supply. Moving the machine with the plug as is inserted can damage

WARNING! the power cord and cause a fire or electric shock. When moving the machine on the floor, retract the Adjusters and ensure that Casters make contact with the floor. During transportation, pay careful attention so that Casters do not tread power cords and earth wires. Damaging the power cords can cause electric shock and short circuit accidents.

J\ When moving the product, do not push the Front Glass. The Glass part could be damaged and glass fractions can cause injury.

CAUTION! When lifting the cabinet, be sure to hold the grip portions or bottom

part. Lifting the cabinet by holding other portions can damage parts and installation portions due to the empty weight of the cabinet, and cause personal injury.

! WHEN MOVING THE PRODUCT, DO NOT PUSH THE FRONT GLASS.

Have the Casters make contact with the floor.

FIG.7

Page 25
  • CONTENTS OF GAME The following are operations and responses obtained when the machine functions satisfactorily. Any functioning different from the following may have been caused by a certain fault. Immediately investigate and eliminate the cause of malfunctioning to ensure satisfactory operation. @ Inserting a coin(s) causes the credit display on the bottom of the screen to count. Inserting one credit worth coin(s) changes the message on the bottom of the screen from "INSERT COIN(S)" to "PRESS START BUTTON" and both of the start buttons will flash. The maximum number of credits counted at a time is 9. Any coin inserted after counting 9 credits will not be counted as any credits, nor be returnable. These coins, however, will count as coins inserted in book-

keeping and the coin meter. @ Pressing either of the start buttons determines which side (left or right) you are playing on. Press the START button to start the game. ® After starting the game, the Title of the Stage being started is displayed. SIGHT

The Cartridge picture shows charged bullets. When your gun runs out of anmo, RELOAD is displayed.

When your gun runs out of ammo, point outside the screen and pull the trigger to reload.

@ The life points and the number of bullets of the left-hand side player (IP) are displayed on the lower left-hand side of the screen, and those of the right-hand side player (2P), on the lower right-hand side of the screen.

@ You lose one life when the dinosaur attacks you.

@ Shooting a human by mis'ake loses one life.

Shooting a human by mistake loses one life.

Page 26

@ The gun holds 5 bullets. When it runs out of ammo, "RELOAD" is displayed on the screen. At this time, point outside the screen and pull the trigger to reload.

@ When the life point becomes zero, the game is over.

@ Downing the boss character awaiting you at the end of each stage results in clearing that particular stage. The player can not defeat the boss until the life meter of the boss becomes zero.

@ Shooting an item on the screen or clearing a specific event allows you to capture an item. Capturing an item strengthens weapons or recovers the life (the explanations regarding the items are stated later on).

@ The Sight Mark sometimes appears on the enemy. At this time, unless the enemy is downed before the sight tums red, the player's life may be lost or the player's status could be extremely unfavorable. Downing the boss character awaiting you at the end of each stage results in clearing that particular stage. The player can not defeat the boss until the life meter of the boss becomes zero.

Unless the enemy is downed before the sight turns red, the player's status could be extremely unfavorable.

Page 27

@ When fighting against the boss character at the end of each stage in the 2 player simultaneous play, if all of the sights can not be shot, the screen will be in the objective mode and in this case either of the players may be taken away by the enemy.

The player who is taken away will remain on the screen as is between the dinosaur's teeth. Herein, he is referred to as Player A.

The other player who is not taken away stays on the screen in the subjective mode. Herein, this player is referred to as Player B.

Player A who is taken away.

SIGHT

At this time, Player B who is not taken away can rescue Player A by shooting all of the sights before the sight attached to the boss turns red.

Although Player A can not shoot with the gun, he can extend the completion time of the sight attached to the boss by repeatedly pressing the Start Button.

If Player B fails to shoot all of the sights before the boss sight becoming red, then Player A will be subject to damage and Player A loses one life.

Page 28

@ If you would like to join in the game at anytime while the other person is playing, insert a coin(s) and press the start button. Also, when credits allowing the game to be played still remain, the start button on the other side will keep flashing. The player can participate in the game by pressing the flashing button. @® When the life point becomes zero, if you want to continue, insert a coin(s) required to continue and press the start button. If credits allowing the player to continue still remain, you can continue by merely pressing the start button. © Atthe time of game over, if the player's score ranks 10th or higher, his name can be entered.

KNACK OF PLAY

TO SHOOT AND DESTROY WHAT EMITS SOUND.

In any stage, the enemy characters other than the boss character will face in the direction where sound is emitted in response to sound and during this time, they stop attacking temporarily. When you are surrounded by plural enemies, shoot anything that emits sound to divert the enemy's attention. Things that emit sound are glass, metal, wooden items, etc.

QUICK SHOT

Shooting the sound emitting items (glass, metals, etc.) causes the dinosaur to respond to the sound produced and the alarm sound emitted by the fellow dinosaur whose head is shot, and thus the enemy temporarily stops attacking.

@ Accurately shoot the head: In each stage, the head part is the weak point of the enemy characters other than the boss. Shooting the head produces a very loud alarm sound which results in the same effect as when shooting what emits sound.

@ Successfully perform an event: Successfully achieving an event which takes place during a stage allows you to favorably proceed with what's coming thereafter. On the other hand, failing to achieve the event causes the enemy attack to become more furious and the situation for the player to be less favorable.

@ Continuously hitting the target enemy without missing earns you high points.

Page 29

REGARDING THE ITEMS

S-POWERBAR (SPECIAL POWER BAR) This increases your “LIFE” by one.

POWERBAR Collecting 3 POWERBARSs increases your “LIFE” by one.

GRENADE GRENADE Hitting this against the earth surface damages the target(s) over a wide a area.

‘ LAA cc During the limited time, there is no limit regarding the number of

grenades that can be used. When the limited time elapses, this returns to an ordinary gun.

SHOT GUN Having a wide scope for hit determination, this damages the target(s) in an extensive area. During the limited time, there is no limit regarding the number of bullets that can be used. When the limited time elapses, this returns to an ordinary gun.

LIGHTNING Hitting a target damages targets within a certain scope from that particular point. During the limited time, there is no limit regarding the number of bullets that can be used. When the limited time elapses, this returns to an ordinary gun.

LASER-SITE The present place at the gunpoint appears on the screen in real time as the pointer. During the limited time, there is no limit regarding the number of bullets that can be used. When the limited time clapses, this returns to an ordinary gun.

Page 30

DINOSAURS appearing in The Lost World: Jurassic Park - The Arcade Game

VELOCIRAPTOR

Alias: RAPTOR Weight: 45 kg. Length: 2m Flesh-eater One of the most ferocious dinosaur in The Lost World. Captures preys by taking an advantage of sharp, long & hook-shaped claws and agile movements as powerful weapons. This dinosaur seems to have brains and skills to pursue spoils in 7 groups.

Appearance in all stages.

MAMENCHISAURUS

Weight: 12t Length: 22m _ Plant-eater MAMENCHISAURUS was a living creature with an approximately 11m long head & neck portion, about the half of the total length, the longest ever (in relation to the physical length) in the terrestrial history. Since the head movements were not so versatile, it might have been able to stand on its rear feet alone sometimes to make up for the handicap. Appearance in Stage 2.

TRICERATOPS Weight: 6t Length: 9m Plant-eater This plant-eater has features of 3 large horns which derive its name and an accessory-like pattern around the neck portion. It’s a gentle dinosaur which eats young buds, etc. with the edge-sharp beak. Appearance in Stage 1.

TYRANNOSAURUS-REX

Alias: TYREX Weight: 6.5t Length: 12m _ Flesh-eater This flesh-eating dinosaur is well-known and the strongest one ever existed in the history. Although physically gigantic, it seems that this dinosaur was able to run fairly quick to pursue preys. The sharp biting attack ability with teeth of a 17 cm. length could be the maximum threat.

Appearance in Stage 1 & ?

Page 31

GALLIMIMUS Weight: 130 kg Length: 4m Omnivorouseater This dinosaur running in groups in the “Jurassic Park” is very impressive. It has the skeletal structure quite similar to an ostrich and its movements are the fastest of all dinosaurs. Having omnivorous-eating habits, it takes insects, small lizards, and fruit.

Appearance in Stage 2.

STEGOSAURUS

Weight: 1.5t Length: 6m Plant-eater A large body and small head as well as the spine are very characteristic. It seems that the 2 pairs of tail spines are utilized for defense, and also, they always act in groups. Appearance in Stage 1.

DILOPHOSAURUS

Alias: Spitter Weight: 1t Length: 6m _ Flesh-eater This dinosaur suddenly became famous as poison spitter in the Jurassic Park. It is distinguished by the large muffler that spreads out to threaten others.

Appearance in Stage 1.

PACHYCEPHALOSAURUS

Alias: PACHY Weight: ? Length: 4.5m _Plant-eater Having the head of a dome-shaped skeletal structure, this dinosaur looks strange as if it had a helmet on. The “helmet” portion is as thick as 25 cm. and surrounded by spike-shaped spines. Did it ferociously fight against the enemies and its rivals sometimes with head butts attack by taking advantage of the rock head?

Appearance in Stage 2.

Page 32

PARASAUROLOPHUS Weight: ? Length: 10m _ Plant-eater The length of the cristated, cylindrical portion of the head is approximately one meter. The cristate is considered to produce cry resonance and to be useful for communicating with fellow dinosaurs belonging to their groups and also instrumental in making amorous approaches.

Appearance in Stage 2.

ANATOSAURUS Weight: 3t Length: 10m _ Plant-eater This belongs to one of the duck-billed dinosaur species, the same as PARASAUROLOPHUS. Its characteristic is the duck-billed wide beak. A number of back teeth allows it to eat hard things >} such as pine needles and nuts.

—e Appearance in Stage 2.

PROCOMPSOGNATHUS

Alias: COMPY Weight: 3kg Length: 60cm _ Flesh-eater This is one of the smallest dinosaurs, only as large as achicken. It can move quickly and catches small animals such as lizards, etc., and sometimes attacks human adults by groups!!

Appearance in Stages 1, 3, and 5.

DEINOSUCHUS

Weight: ? Length: 15m _ Flesh-eater The name is derived from “fearful Alligator.” Although belonging to the specie different from the dinosaur, this is a ferocious flesh-eater which attacks living creatures and fish at the waterside. The length is said to be 15m though the appearance is almost the same as currently existing alligators. Its weapons are the jaws lined up with sharp teeth and the strong tail.

Appearance in Stage 2.

Page 33

PTERANODON Weight: 17 kg. Length: 7m (when wings are opened) _-Flesh-eater PTERANODON signifies that it has wings and is toothless. It used to glide through the air like a glider with large wings spread out. Freely flying through the sky, it pursues spoils from above with its sharp beak.

Appearance in Stage 4.

CARNOTAURUS Weight: ? Length: 12m _ Flesh-eater The characteristics are a short, strange looks with two large spines. In the “Lost World,” the original novel, this is given a setting as Chameleon Dinosaur and captures preys which come near by without knowing that this dinosaur uses the technique in which it camouflages itself by changing its physical color adapted to the surrounding scenery.

Appearance in Stage 4.

Page 34
  • EXPLANATION OF TEST AND DATA DISPLAY

By operating the switch unit, periodically perform the tests and data check. When installing the machine initially or collecting cash, or when the machine does not function correctly, perform checking in accordance with the explanations given in this section. The following shows tests and modes that should be utilized as applicable.

TABLE 9 EXPLANATION OF TEST MODE

DESCRIPTION SECTIONS INSTALLATION | When the machine is installed, perform the following: OF MACHINE REFERENCE

  • Check to see that each setting is as per standard setting made | 9-7, 9-8, 9-9 at the time of shipment.
  • In the INPUT TEST mode, check each SW and VR. 9-4
  • In the OUTPUT TEST mode, check each of lamps. 9-10
  • Inthe MEMORY TEST mode, check ICs on the IC Board. 9-3
MEMORYChoose MEMORY TEST in the MENU mode to allow the9-3

MEMORY test to be performed. In this test, PROGRAM RAMs, ROMs, and ICs on the IC Board are checked.

PERIODIC Periodically perform the following: SERVICING

  • MEMORY TEST 9-3
  • Ascertain each setting. 9-7, 9-8, 9-9
  • In the INPUT TEST mode, test the CONTROL device 9-4
  • In the OUTPUT TEST mode, check each of lamps. 9-10
CONTROL1. In the INPUT TEST mode, check each SW and VR.9-4

SYSTEM

  • Adjust or replace each SW and VR. 10
  • If the problem can not be solved yet, check the CONTROL's 10 moves.
MONITORIn the MONITOR ADJUSTMENT mode, check to see if the9-6

PROJECTOR adjustment is appropriately made.

IC BOARD1. MEMORY TEST9-3
  • In the SOUND TEST mode, check the sound related ROMs. | 9-5
DATA CHECKCheck such data as game play time and histogram to adjust the9-7, 9-11

difficulty level, etc..

Page 35

9-1 SWITCH UNIT AND COIN METER

A Never touch places other than those specified. Touching places not

specified can cause electric shock and short circuit.

WARNING!

S @ Adjust to the optimum sound volume by considering the environmental

requirements of the installation location.

IMPORTANT! @ Ifthe COIN METER and the game board are electrically disconnected,

game play is not possible.

Open FRONT DOOR (RIGHT), and the Switch Unit shown appears. The function of each switch is as follows:

VOLUME SERYCE TR CEMA TIER O° ce) j ©) : iN SPEAKER_VOLUME, SERVICE BUTTON. TEST BUTTON DEMAGNETIZER SW.

FIG. 9. 1a SWITCH UNIT

TEST BUTTON (TEST SW) : For the handling of the TEST BUTTON, refer to the following pages.

SERVICE BUTTON (SERVICE SW): Gives credits without registering on the coin meter.

SPEAKER VOLUME (VOLUME) — : Adjusts the volume of all of the Speakers.

DEMAGNETIZER SWITCH : Eliminates the unevenness of MONITOR's on-screen color.

Open the Cashbox Door by using the key to have the Coin Meter appear underneath the Cashbox.

COIN METER Counts the number of coins

FIG. 9.1 b COIN METER

Page 36

9-2 TEST MODE

S In case settings are changed in GAME ASSIGNMENTS, COIN

ASSIGNMENTS, and GUN SETTING, the setting changes are not effective

IMPORTANT! unless the test mode is exited and the game mode returns on the screen. The setting changes are ineffective if power is turned off in the test mode.

This mainly checks if the operation of the game BD is accurate, and allows for COIN ASSIGNMENTS/GAME ASSIGNMENTS setting and Moniter adjustments.

SELECTION OF TEST ITEMS

TEST MENU @ Push the TEST BUTTON to cause the follow-

icipaaiiliad ing TEST MENU to appear: Serre ReclcnseNrs, @ By pushing the SERVICE BUTTON, bring the oureur Test the TEST BUTTON

SOUND TEST

COIN ASSIGNMENTS arrow mark ">" to the desired item and press oureur Test the TEST BUTTON. BOOKKEEPING BACKUP DATA CLEAR > EXIT © After the test is complete, move ">" to "EXIT" and press the TEST BUTTON to return to the SELECT WITH SEAVICE BUTTON Game Mode. AND PRESS TEST BUTTON

FIG. 9.2 TEST MENU

9-3 MEMORY TEST

MEMORY TEST The MEMORY TEST mode is for checking the on-BD memory IC functioning. "GOOD" is displayed for normal ICs and "BAD" is displayed for abnormal ICs.

@ When the test is completed, if the display is as shown left, it is satisfactory.

@ After finishing the test, pressing the TEST BUTTON allows the MENU mode to return PRESS TEST BUTTON TO EXIT on to the screen.

FIG. 9.3 MEMORY TEST

Page 37

9-4 INPUT TEST

When INPUT TEST is selected, the monitor will show the following, allowing you to watch the status of each switch. On this screen, periodically check the status of each switch.

INPUT TEST PLAYER 1 PLAYER 2 TRIGGER off oft START off ot COIN CHUTE #1 off COIN CHUTE #2 olf SERVICE off TEST

PRESS TEST BUTTON TO EXIT

FIG.9.4 INPUT TEST

9-5 SOUND TEST

‘SOUND TEST

VoIct Sa

SELECT WITH SERVICE BUTTON ‘AND PRESS TEST BUTTON

FIG. 9.5 SOUND TEST @ By pressing each switch, if the display on the right-hand side of the name of each switch changes to on from off, the SW and the wiring connections are satisfactory.

@ Open the Coin Chute Door and insert a coin into the Coin Entry to check Coin Chute Coin SW. Note that depending on the destination, this product may not be equipped with COIN CHUTE #2.

Press the Test button to return to the Test Menu mode (FIG. 9.2).

This enables sounds used in the game to be checked. Sound related memory and each speaker are checked.

By using the Service button, bring the arrow to select the desired sound item to be checked. Each time the Test button is pressed, the numeral beside the selected item increases by one and the sound is emitted sequentially in order.

Choose EXIT and press the Test button to return to the menu mode (FIG. 9. 2).

Page 38

9-6 C.R.T. TEST

Select C. R. T. Test to cause the Monitor to display CRT. TEST 1/2 the screen shown left, allowing Monitor adjustment status to be checked.

Periodically check the Monitor adjustment status on this screen.

The screen (1/2) enables color adjustment check to be performed. The color bar of each of the 4 colors, i. e., red, green, blue and white, is darkest at the extreme left and becomes brighter towards the PRESS TEST BUTTON TO CONTINUE extreme right.

Press the TEST BUTTON to shift to the next page (2/2). FIG.9.6a C.R.T TEST (1/2)

The screen (2/2) allows screen size and distortion to be tested.

Check if the Crosshatch Frame Line goes out of the screen and if the crosshatch lines are distorted.

Press the TEST BUTTON to return to the Menu mode. (FIG. 9. 2)

FIG.9.6b C.R.T TEST (2/2)

Page 39

9-7 GAME ASSIGNMENTS

Selecting the GAME ASSIGNMENTS in the menu mode causes the present game setting to be displayed and also the game setting changes (game difficulty, etc.) can be made. Each item displays the following content.

SETTING CHANGE PROCEDURE

S The setting changes are ineffective unless "EXIT" is selected in the menu

IMPORTANT! jj change. mode (FIG. 9. 2). Be sure to exit from the test mode after the setting

@ Press the SERVICE BUTTON to move the arrow ">" to the desired item.

@ Choose the desired setting change item by using the TEST BUTTON.

@® To return to the MENU mode, move the arrow to EXIT and press the TEST BUTTON.

GAME ASSIGNMENTS.

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON

FIG. 9.7 GAME ASSIGNMENTS GAME DIFFICULTY Game Difficulty can be set in 16 different levels.

ADVERTISE SOUND Determines whether ADVERTISE SOUND is to be emitted or not by setting to ON when emitting it and to OFF when not emitting it.

LIFE The INITIAL LIFE (the number of life points allotted to the player at the time of game start) can be selected from the 9 categories.

BOSS ACTION The setting of the last Boss Character is performed. NORMAL enables LIFE recovery. MILD disables LIFE recovery.

Page 40

9-8 COIN ASSIGNMENTS

The "COIN ASSIGNMENTS" mode permits you to set the start number of credits, as well as the basic numbers of coins and credits. This mode expresses "how many coins correspond to how many credits."

SETTING CHANGE PROCEDURE

S The setting changes are ineffective unless "EXIT" is selected in the menu

mode (FIG. 9. 2). Be sure to exit from the test mode after the setting

IMPORTANT! |] change.

COIN. ASSIGNMENTS

CREDIT TO START CONTINUE . a

Note that depending on the destination, this product may not be equipped with COIN CHUTE #2. COIN/CREDIT SETTING CHUTE #1 COIN TCREDIT

GWE #2 TCOIN 1CREDIT

WANUAL SETTING

> IT

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON

FIG. 9.8 a COIN ASSIGNMENTS

@ CREDIT TO START / CREDIT TO CONTINUE Number of credits required for starting game and for continuing game are set. The eleven sets of these combinations are available as follows:

START: 1 2 3 3 4 4 4 5 5 5 5 CONTINUE : 1 1 1 2 1 2 3 1 2 3

@ COIN/CREDIT SETTING Sets the CREDIT increase increment per coin insertion. There are 27 settings from #1 to #27, expressed in QO CREDIT as against OO COINS inserted. #27 refers to FREE PLAY (refer to TABLE 9. 8 a).

@ MANUAL SETTING

This allows credit increase setting as against coin insertion to be further set in the manner finer than COIN/CREDIT SETTING (refer to TABLE 9. 8 b).

Page 41

HOW TO USE THE TEST MODE

Selecting MANUAL SETTING in the Coin Assignment mode displays the following screen.

COIN ASSIGNMENTS MANUAL SETTING

  • COIN ICREDIT NO BONUS ADDER COIN TO CREDIT BOUNUS ADDER

COIN CHUTE #1 MULTIPIER 1 COIN COUNTS AS 1 COIN

COIN CHUTE #2. MULTIPIER 1 COIN COUNTS AS 1 COIN > EXIT

‘SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON

FIG. 9.8b MANUAL SETTING @ Determines Coin /Credit setting.

@ This sets how many coins should be inserted to obtain one Service Coin.

@ This sets how many tokens one coin represents.

Table 9.8b MANUAL SETTING

COIN TO CREDIT CREDIT CREDIT CREDIT CREDIT CREDIT CREDIT CREDIT CREDIT

BONUS ADDER

COIN CHUTE MULTIPLIER 2 COINS 3 COINS 4 COINS 5 COINS 6 COINS 7 COINS

9 COINS GIVE 1 EXTRA COIN

1 COIN COUNTS AS 1 COIN 1 COIN COUNTS AS 2 COINS 1 COIN COUNTS AS 3 COINS 1 COIN COUNTS AS 4 COINS 1 COIN COUNTS AS 5 COINS

1 COIN COUNTS AS 7 COINS 1 COIN COUNTS AS 8 COINS 1 COIN COUNTS AS 9 COINS

Page 42

9-9 GUN SETTING

S The setting changes are ineffective unless "EXIT" is selected in the menu

mode (FIG. 9. 2). Be sure to exit from the test mode after the setting

IMPORTANT! jj change. Selecting GUN SETTING causes the following screen shown at the top to appear. This allows the controller sighting to be adjusted. Periodically check the sighting adjustment status on this screen.

The screen shown left is the sighting adjustment oxen menu mode. Press the SERVICE button to bring the GUN MARK CHECK arrow to the desired adjustment item to check. Press > ae the Test button to have the following adjustment menu mode appear on the screen. Bring the arrow to EXIT and press the TEST button to return to the menu mode (FIG. 9. 2).

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON

FIG. 9.9a SIGHTING ADJUSTMENT MENU

Selecting GUN MARK CHECK causes the screen at the left to appear (the intersecting point of the 2 straight lines indicates the center of the screen).

eatoe oe Point the Controller to this screen to have a square

beseiet a4) basal td cursor appear (1P side is blue and 2P side is red). This cursor indicates an impact mark. Point the Controller at the screen and trigger to have a small LOUT OF $¢REEN 1P) square remain on the screen as impact mark. (OUT OF $EREEN {P| Perform sighting check on this screen. Press the Test button to return to the above sighting adjustment menu screen. ~ ~ ~

CURSOR (Impact Position) IMPACT MARK

CURSOR for IP is blue and for 2P, red.

FIG. 9.9b SIGHTING CHECK

Page 43

Select GUN ADJUSTMENT to display the following screen. In this mode, the 4 Adjustment values (for on-screen right end, left end, upper end and lower end) are set. Each adjustment value is set as follows. Be sure to determine the adjustment value by actually pointing the Controller at the end of the designated direction (the cursor value is preset). Select each adjustment position by using the 1P or 2P Start button. Press the Test button to return to the SIGHTING ADJUSTMENT mode.

Senos Sireenstpos sereen¥pos

RIGHT LeET ‘TOP. > BOTTOM CENTER BOTTOM > CENTER

FIG. 9.9 ¢ SIGHTING ADJUSTMENT

The Cursor is in the pre-setting For the actual sighting adjustment, trigger while each end of the on-screen 4 sides being aimed at by the Controller regardless of the Cursor.

RIGHT aa:bb LEFT aa:bb Determine the adjustment value of the screen’s right-hand end in the horizontal directions. The left side value (aa) indicates the pre-setting value, and the right side value (bb) refers to the value to be newly inputted. By pointing the Controller to the right end of the screen, determine the adjustment value while actually aiming the Controller at the right end of the screen with the Controller and triggering regardless of the cursor. At this time, disregard the vertical directions.

TOP aa:bb Determines the adjustment value of the screen’s upper end in the vertical direction. The left side value (aa) indicates the pre-setting value, and the right side value (bb) refers to the value to be newly inputted, By pointing the Controller to the upper end of the screen, dete: justment value while actual, ing the Controller at the upper end of the screen and triggering regardless of the cursor. At this time, disregard the horizontal directions.

CENTER X aa:bb

Y aa:bb Determines the adjustment value of the screen’s center. Determine the adjustment value of the screen’s left-hand end in the horizontal direction. The left side value (aa) indicates the pre-setting value, and the right side value (bb) refers to the value to be newly inputted. By pointing the Controller to the left end of the screen, determine the adjustment value while actually aiming the Controller at the left end of the screen and triggering regardless of sor. At this time, disregard the vertical directions.

BOTTOM aa:bb Determines the adjustment value of the screen’s lower end in the vertical direction. The left side value (aa) indicates the pre-setting value, and the right side value (bb) refers to the value to be newly inputted. By pointing the Controller to the lower end of the screen, determine the adjustment value while actually aiming the Controller at the lower end of the screen and triggering regardless of the cursor. At this time, disregard the horizontal directions.

X and Y respectively indicates left/right and up/down directions. The left -hand side value (aa) indicates the pre-setting value, and the right-hand side value (bb) refers to the value to be newly inputted. By pointing the Controller to the center of the screen, determine the adjustment value while actually aiming the Controller at the center of the screen and triggering regardless of the cursor.

Page 44

9-10 OUTPUT TEST

  • Choose OUTPUT TEST to have the MONITOR PLAYER screen shown left appear. This screen allows lamp PLAYER 2 status to be checked. Periodically check the lamp ROOM LIGHT status in this mode. > MARS LIGHT exit Select the desired item to be checked. If each of IP and 2P buttons flashes, it is satisfactory. Note that though ROOM LIGHT and MARS LIGHT are displayed on the screen, the U/R Cabinet is not equipped with these. SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON

FIG. 9.10 OUTPUT TEST

BUTTONS FLASH.

Choose EXIT and press the Test button to return to the Menu mode (FIG. 9. 2).

Page 45

9-11 BOOKKEEPING

Choosing BOOKKEEPING in the menu mode displays the data of operating status up to the present are shown on 2 pages. PAGE 1/2 shows COIN/CREDIT related data. Press the Test button to proceed to PAGE 2/2.

BOOKKEEPING 1/2

COIN CHUTE #1 XXXXXXXXXXX COIN GHUTE #2 XXXXXXXXXXX a XXXXXXXXXXX XXXXXXXXXXX XXXXXXXXXXX XXXXXXXXXXX XXXXXXXXXXX XDXXHXXMXXS XDXXHXXMXXS_ XDXXHXXMXXS, XDXXHXXMXXS XDXXHXXMXXS.

PRESS TEST BUTTON TO CONTINUE

FIG. 9.11 a BOOKKEEPING(1/2)

BOOKKEEPING 2/2

TIME HISTOGRAM

Insos

ast

ae

ove AXON

PRESS TEST BUTTON TO EXIT

FIG. 9.11 b BOOKKEEPING(2/2) COIN CHUTE #1,2: Number of coins put in each Coin Chute.

TOTAL COINS: Total number of activations of coin chutes

COIN CREDITS: Number of credits registered by inserting coins

SERVICE CREDITS: Credits registered by the SERVICE BUTTON

TOTAL CREDITS: Total number of credits (COIN CREDITS + SERVICE CREDITS)

NUMBER OF GAMES: Total number of plays

TOTAL TIME: Total energized time

AVERAGE PLAY TIME:

LONGEST PLAY TIME:

SHORTEST PLAY TIME:

On page (2/2), each play frequency is displayed. When setting difficulty levels, the frequency can be referred to as a standard.

When in the PAGE 2/2 mode, press the Test button to return to the Menu mode (FIG. 9.2).

Page 46

9—12 BACKUP DATA CLEAR

Clears the contents of BOOKKEEPING and high BAKCUP DATA CLEAR score player ranking entry. When clearing the contents, bring the arrow to "YES" and press the test > YES(CLEAR) button. When the data has been cleared, NO (CANCEL) "COMPLETED" is displayed. Press the Test button to return to the menu mode (FIG. 9.2). Bringing the arrow to "NO" and pressing the Test button causes the menu mode to return to the screen. Note that the contents of game assignments and sighting adjustment are not affected by BACKUP DATA CLEAR operation. SELECT WITH SERVICE BUTTON ‘AND PRESS TEST BUTTON

FIG. 9.12. BACKUP DATA CLEAR

Page 47

10. CONTROLLER (GUN)

A

WARNING!

@ In order to prevent an electric shock and short circuit, be sure to turn power off before performing work by touching the interior parts of the product. @ Be careful so as not to damage wirings. Damaged wiring can cause an electric shock or short circuit accident.

In the cases where the controller's operation is not satisfactory or the controller sight deviates from the direction in which the controller is pointed, the controller's interior parts may have been damaged. Replace the parts by disassembling the controller in the following procedure: Also, be sure to perform sighting check in the test mode when the controller parts are replaced.

REPLACING THE MICROSWITCH

1)

®

© e68®o Disassemble the controller.

Pull out the microswitch from COVER RIGHT.

Take out the microswitch by removing the soldering from it.

Bend the new Microswitch Actuator as shown.

Solder the new microswitch and assemble the controller.

By operating the Trigger, check if the Microswitch can be turned ON/OFF correctly.

REPLACING THE SENSOR UNIT

®

®@ Disassemble the controller.

Remove the sensor unit from COVER.

Page 48

MICROSWITCH ACTUATOR BENDING WORK Approximately 8 mm Approximately 7 mm | @ FIG. 10 CAP_NUT_(9) M3

a.

ha \

<i ie

a JPT-2030

MBX 25 M3 xX 8 MICROSWITCH 509-5080,

Page 49
  • COIN SELECTOR

HANDLING THE COIN JAM

If the coin is not rejected when the REJECT button is pressed, open the coin chute door and open the selector gate. After removing the jammed coin, put a normal coin in and check to see that the selector correctly functions.

CLEANING THE COIN SELECTOR

The coin selector should be cleaned once every 3 months. When cleaning, follow the procedure below: Turn the power for the machine OFF. Open the coin chute door. Open the gate and dust off by using a soft brush (made of wool, etc.). Remove and clean smears by using a soft cloth dipped in water or diluted chemical detergent and then squeezed dry. Remove the CRADLE. When removing the retaining ring (E ring), be very careful so as not to bend the shaft. Remove stain from the shaft and pillow portions by wiping off with a soft cloth, etc. After wiping off as per ©) above, further apply a dry cloth, etc. to cause the coin selector to dry completely. © © © oO

©

S @ Never apply machine oil,

etc. to the Coin Selector.

IMPORTANT! @ After cleaning the Coin

Selector, insert a regular coin in the normal working status and ensure that the Selector correctly functions.

Insert a coin

COIN INSERTION TEST the Reject

Once every month, when performing Button the Coin SW Test, simultaneously Pressed down . id check if check the following: at is rejected,

Does the Coin Meter count satisfactorily? COIN METER Does the coin drop into the Cashbox correctly? Is the coin rejected when inserted while keeping the Reject Button pressed down?

FIG. llc

Page 50
  • MONITOR 12—1 CAUTIONS AND WARNINGS CONCERNING THE SAFETY FOR HANDLING THE MONITORS Before handling the monitors, be sure to read the following explanations and comply with the
caution/warning instructions given below. Note that the caution/waming symbol marks and letters are used in the instructions. Indicates that handling the monitors Indicates that handling the monitors by erroneously by disregarding this warning disregarding this caution may cause a may cause a potentially hazardous situation, potentially hazardous situation, which could
WARNING! which could result in death or serious injury. CAUTION! result in personal injury and or material ie * damage. Indicates that access to a specific part of the Indicates the instruction to disconnect a equipment is forbidden. power connector or to unplug.

@ When performing such work as installing and removing the monitor, inserting and disconnecting the external connectors to and from monitor interior and the monitor, be sure to disconnect the power connector (plug) before starting the work. Proceeding the work without following this instruction can cause electric shock or malfunctioning.

WARNING! @ Using the monitor by converting it without obtaining a prior permission is not allowed. SEGA 7 shall not be liable for any malfunctioning and accident caused by said conversion.

@ Primary side and Secondary side The monitor's circuit which is divided into the Primary side SECONDARY SIDE and Secondary side, is electrically isolated. Do not touch the (Chassis, CRT) primary side, or do not touch both the primary side and the secondary side simultaneously. Failing to observe the instruction can cause electric shock and this is very dangerous. When making monitor adjustments, use a nonconductive driver and make adjustment without touching any part other than the Adjustment V. R. and knob. Also, be sure not to cause a short-circuit to the Primary side and Secondary side. If short-circuited, it can cause electric shock or malfunctioning, which is very dangerous. @ High-tension Voltage Some of the parts inside monitor are subject to high-tension voltage in excess of 20,000 volts and very dangerous. Therefore, do not touch the monitor interior. Should soldering & paper wastes, etc. be mixed in the monitor interior, turn the power off so as not to cause malfunctioning or fire hazard. rove CAP PRIMARY SIDE DEMAGNETIZER___REAR PART TL ANODE LEAD Mainsp © © ‘Approx. 29 kV ar =

DEMAGNETIZER FOCUS LEAD iS)

COIL (black) SS a Approx. 10 kV NECK PCB

SECONDARY SIDE FBT Approx.

(Chassis, sheet metal work, CRT, etc.) 4 Disconnect or unplug 29 kV

@ Connecting the CRT and PCB For combining the CRT and PCB, use the specified part No. to maintain the status of adjustments made at the factory. The anode of the CRT itself will be accumulatively charged as time elapses, generating high-tension voltage which is very dangerous. The monitor should be used with the Chassis, CRT and PCB assembled. When repair, etc. is required at the time of malfunctioning, be sure to send it in an "as is assembled" condition. If these are disassembled, what's charged to said high tension voltage can be discharged, causing a very hazardous situation. Therefore, under no circumstances should it be disassembled.

@ Static Electricity Touching the CRT surface sometimes causes you to slightly feel electricity. This is because the CRT surfaces are subject to static and will not adversely affect the human body. @ Installation and removal

CAUTION! Ensure that the Magnetizer Coil, FBT (Fly-Back Transformer), Anode Lead and Focus Lead are not positioned close to the sheet metal work's sharp edges, etc. and avoid damaging the insulated portions so as not to cause electric shock and malfunctioning. (For the name of parts, refer to the above Figures).
Page 51

\ For the purpose of static prevention, special coating is applied to the CRT face of this product. To protect the coating, pay attention to the following

CAUTION! points. Damaging the coating film can cause electric shock to the

customers. For the caution to be heeded when cleaning, refer to the Section of Periodic Inspection Table. @ Do not apply or rub with a hard item (a rod with pointed edge, pen, etc.) to or on the CRT surfaces. Avoid applying stickers, seals, etc. on the CRT face. Do not remove aluminum foils from the CRT corners. Removing the aluminum foils can cause static prevention effects to be lowered. Aluminum Foi!

12—2 CLEANING THE CRT

CAUTION!

S @ When cleaning the CRT, be sure to use a soft, dry cloth. Do not use

chemicals such as thinner, benzene, etc. INPORTANT! @ Apply anti-static agent,which prevents dust attachment, only to the CRT ‘ face.

Be sure to turn power off before cleaning the CRT.

GLASS HOLDER UPPER

When cleaning the CRT, remove GLASS HOLDER UPPER and the TRUSS SCREW (3) FRONT GLASS. MS x 16, black FRONT GLASS

Page 52

42—3 ADJUSTMENT METHOD

A\ @ Monitor adjustments have been made at the time of shipment. Therefore, do not make further adjustment without a justifiable reason.

WARNING! Adjusting the monitor which contains high tension parts is a dangerous . work. Also, an erroneous adjustment can cause deviated synchronization and image fault, resulting in malfunctioning. When making adjustment, utilize a resinous Alignment Screwdriver. Servicing with bare hand or using conductive tools can cause electric shock accidents.

Remove the back door at the rear of the cabinet, and the monitor adjustment knob appears.

@ Take off the 3 tamperproof screws to remove the back door.

TAMPERPROOF_SCREW(3) M4X30, using flat washer

FIG. 12.3

@ There are 3 types of Monitor that can be used for this product. Depending on the specific monitor,

the knob layout varies.

Page 53

NANAO monitor: 2-2 4—0 5 (24K mode) 200-52 200-53 —24-—0 1 (24K mode) NANAO monitor:

Heese We Aa

DO@OOH OD OW

SANWA monitor: 200—5 2 43—2 4-—0 1 (24K mode)

Ooe8@eeaeegeeag

© @ OO © © OF ®O ®@ RGAIN GGAIN BGAIN BRIGHT HSIZE HHOLD HPOSI VSIZE VHOLD VPOSI

POSOLHVOOSHoOHNO R-GAIN ....

G-GAIN Controls colors.

B-GAIN ....2

BRIGHT ......... Controls screen brightness.

H. SIZE uu... Controls horizontal screen size.

H. HOLD ........ Provides horizontal synchronization, i.e., controls right/left hold.

H. POSL........... Controls horizontal display position on screen.

V. SIZE woesseecses Controls vertical screen size.

V. HOLD ........ Provides vertical synchronization, i.e., controls up-down hold.

V. POST wees Controls vertical display position on screen.

CONTRAST ... Adjusts image contrast.

Page 54
  • REPLACEMENT OF FLUORESCENT LAMP AND LAMPS

A

WARNING!

A

CAUTION!

When performing the work, be sure to turn power off. Working with power on can cause electric shock and short circuit accidents. @ The Fluorescent Lamp, when it gets hot, can cause burns. Be very careful when replacing the Fluorescent Lamp. @ Be sure to use the lamp of the specified rating. Using lamps of nonspecified rating can cause a fire or malfunctioning.

To perform work safely and securely, be sure to prepare a step which is in a secure and stable condition. Not using a step or using an unstable step can cause a violent falling down accidents.

143—1 REPLACEMENT OF FLUORESCENT LAMP

After removing Lamp Cover B and Billboard Plate as per FIG. 6. 1 a, Section 6, take out the 2 screws, remove Lamp Cover A, and replace the Fluorescent Lamp.

FLATHEAD SCREW (2) Mt x 8, black

FLUORESCENT LAMP_20W :_390-5251-20-20 GLOW BULB + 390-5638-1E

LAMP _COVER_A

PREPARE A STEP TO PERFORM WORK.

Page 55

13—2 LAMP REPLACEMENT

@ Take off the 6 Tamperproof Screws and remove the Switch Panel. (FIG. 13. 2 a)

@ _ Pull the lower part of the Switch from the rear of the Switch Panel and remove the Switch part to replace the lamp. (FIG. 13. 2 b)

SWITCH PANEL

TAMPERPROOF SCREWS (6) M48, chromium plated

5 : OD 2

; 2

Z ye og

FIG. 13.2a .

LAMP _6V_3W 390-5160

> al © FIG. 13.26

Page 56
  • PERIODIC INSPECTION TABLE The items listed below require periodic check and maintenance to retain the performance of this machine and ensure safe operation. When handling the controller, the player will be in direct contact with it. In order to always allow the player to enjoy the game, be sure to clean it regularly. Also, it is advisable to provide wet tissue, etc. available for player use.

@ Be sure to check once a year to see if Power Cords are damaged, the plug is securely inserted, dust is accumulated between the Socket

WARNING! Outlet and the Power Plug, etc. Using the product with dust as is : accumulated can cause a fire or electric shock. @ Periodically once a year, request the place of contact herein stated or the Distributor, etc. where the product was purchased from, as regards the interior cleaning. Using the product with dust as is accumulated in the interior without cleaning can cause a fire or accident. Note that cleaning the interior parts can be performed on a pay-basis.

ITEMS DESCRIPTION PERIOD REFERENCE

CONTROLLER Cleaning As necessary

Sight checkWeekly9

Check SWes. Monthly 9

COIN SELECTORCheck COIN SWes.Monthly9
COIN SELECTOR cleaning.Trimonthly11

MONITOR C.R.T. cleaning. Weekly 12

Check adjustments.Monthly6. 9. 12
FRONT GLASS, MIRRORCleaningWeeklySee FIG. 14
GAME BDSetting checkMonthly9
| INTERIORCleaningAnnuallySee above.

POWER PLUG Inspection and cleaning

CLEANING THE FRONT GLASS AND MIRROR When cleaning, be sure to comply with the following CAUTION and instructions so as to ensure that the front glass and mirror are not damaged.

I

CAUTION @ Be sure to use the accessory glass cleaner or high-efficiency alkaline

cleansing water. To avoid damaging the glass surfaces, do not use solutions such as thinner and alcohol, or abrasives, nor bleaching | agents.

IMPORTANT! @ Use a soft cloth. ; : ‘ @ When removing an attached large particle of dust (or foreign matter), do not rub with a cloth.

Remove the front glass when cleaning the front glass and mirror. First, remove GLASS HOLDER UPPER only. Then, put your hand through the square hole in the back side of GLASS HOLDER UPPER, and pull the TRUSS SCREW (3) front glass toward you. 5X16, black FIG. 14 VW

Page 57
  • TROUBLESHOOTING

Should trouble occur, first check wiring connector connections.

PROBLEMS CAUSE COUNTERMEASURES

With Main SW ON, no activation. Power is not supplied. Securely insert the power plug into the plug socket.

Power supply/voltage is not correct. Make sure that power supply/voltage is correct.

The Circuit Protector functioned due to the momentary overload. After eliminating the cause of overload, reinstate the AC Unit's Circuit Protector.

The CONNECT BOARD fuse is blown due to the momentary overload.

The monitor screen sways or shrinks.

No sound is emitted. The power supply voltage is not correct. After eliminating the cause of overload, replace the CONNECT BOARD fuse (see next page). 514-5036-5000 FUSE 6.4 ¢ X30 5000mA 125V

Ensure that the power supply voltage is correct.

Sound volume adjustment is not appropriate. Adjust sound volume (see Section 9).

Board and Amplifier malfunctioning,

Controller sighting is not satisfactory. Due to environmental changes, etc., sighting became inappropriate. Perform the sound test and confirm (see Section 9).

Perform sighting adjustment in the test mode (see Section 9).

LED BD malfunctioning. Check to ensure that the LED lights up. If it does not light up, replace.

Sensor Unit malfunctioning. Replace the Sensor Unit.

LED BD, Front Glass, and Mirror are soiled.

The Fluorescent lamp does not light up. The Fluorescent tube is burnt out.

The Lamp does not light up. Lamp malfunctioning. Wipe off soiled surfaces (see Sec. 14 and next page).

Replace the Fluorescent tube (refer to Sction 13).

Replace the Lamp (see Section 13).

Page 58

REPLACEMENT OF LED BD

If the light emission of 2 LED’s can not be seen, the fault or malfunctioning may be considered. Replace by using the following procedure. Also, when wiping off the soils, remove the ASSY SENSOR as per the same procedure.

a gs

q 0 je oS }

INA light emission from the 2 LED's can not be seen, replace.

FIG. 15a

@® Turn power off.

@ Remove the Back Door.

@® Disconnect the ASSY SENSOR CONNECTOR.

@ Pull out the ASSY SENSOR.

© Disconnect the connector from the both ends of the LED BD which shows defects.

@© Take out the 2 U Nuts to remove and replace the LED BD. LED ASSY_ SENSOR

BD U_NUT_(2)

Page 59

REPLACEMENT OF FUSE

man In order to prevent an electric shock accident, be sure to turn power off

before performing work by touching the interior parts of the product.

WARNING! Be careful so as not to damage wirings. Damaged wiring can cause an electric shock or short circuit accident. Be sure to use fuses meeting specified rating. Using fuses exceeding the specified rating can cause a fire or electric shock. After eliminating the cause of the fuse blowing, replace the fuse. Depending on the cause of fuse blowing, continued use with the fuse as is blown can cause generation of heat resulting in a fire.

By referring to 12 - 3, remove the Back Door and replace the AC Unit Fuse.

PHOTO 15

Page 60
  • GAME BOARD

A

WARNING!

A

CAUTION!

16-1 In order to prevent electric shock and short circuit accidents, be sure to turn power off before performing work by touching the interior parts of the product. Be careful so as not to damage wirings. Damaged wiring can cause a fire or electric shock and short circuit accidents. Do not expose the Game BC, etc. without a justifiable reason. Exposed Game BD, etc. can cause electric shock accidents and malfunctioning.

The electronic parts on the IC Board could be damaged due to human body's static electricity. Before performing IC Board related work, be sure to discharge physically accumulated statics by touching grounded metallic surfaces. @ When asking for the replacement or repair of the product's Game Board (MODEL 3 BOARD), be sure to put the Game Board together with the Shield Case in a Carton Box. Otherwise, the request is not acceptable.

REM OVING THE BOARD To replace the IC BD (such as GAME BD, I/O BD, etc.) , take out the IC BD by using the following procedure: Tur the MAIN SW off. Take off the screw to unlock and open FRONT DOOR LEFT. Depending on cabinets, the front door may not have this screw. The shield case is contained inside FRONT DOOR LEFT. Disconnect all the Connectors which connect the Base and the Cabinet. The shield case is secured to the base (wooden). Take off the wing bolt which secures the base to the cabinet and take out the shield case together with the base. (OX)

© ©6068

Take off the 3 screws to remove the case lid. The game BD is contained in the shield case. Loe

p SHIELD CASE

Disconnect s all the Connectors

CASE LID SCREWS _(3) A M4X8, w/flat & spring washers FIG. 16.1

Page 61

16—2 COMPOSITION OF GAME BOARD

GAME BD JPT (833-13171)

SCREW (10) (355, using flat & spring washers SCREW (5) M3X35, using flat & = spring washers

FIG. 16.2

PART No. DESCRIPTION

837-12874 MODEL3 STEP 1.5 CPU BOARD 837-12874-01 MODEL3 STEP 1.5 CPU BD W/GND BD 837-12875 MODEL3 STEP 1.5 VIDEO BOARD

834-13172 ROM BD THE LOST WORLD

Page 62
  • DESIGN RELATED PARTS For the Warning Display stickers, refer to Section 1.

WN Ld Nd LNOD HS NOIS30

81022-L To\ Lt YIN Id? 3LV1d YISNI ONG Y/N ddf HS ULSNI AVId WEZ- Id TO-S290-22F WN Id? 4 30S Y3XOILS WN Id? JlVId GHVOETIG / WA Id? 1 30S Y3XOILS 70S 2060-627 / €0G- 1dr

YIN Id? Nd dod 9 10-627

Page 63
  • PARTS LIST

@ TOP ASSY THE LOST WORLD U/R (0-1/2)

=e

» o®? >e @= z Be CLE

Page 64

@ TOP ASSY THE LOST WORLD U/R

ITEM NO.

oye wNe

XAANANNNNANN PART NO.

JPT-10001 JPT-2300 422-0625-01 421-1907- ~ 421-6594-91 421-7987 421-8408 421-7988-91 421-8479-01 440-DS0013XEG SGM-4323 440-WS0002XEG 440-CS0109-BG PRC-1045

008-T00408-0C 090-0024 008-T00408-0B

601-6604-30 SGM-2675 420-6325-03 220-5576 SGM-4111 540-0006-01 540-0007-01 514-5036-5000 509-5080 390-5160 600-6724 600-6729 600-6618 SGM-4441 423-0302 429-0144 090-0174

105-5216 601-7975 008-100412-0C 050-F00400 008-T00408-0C GPD-0002X 421-8740 421-6690-03 421-6690-05 421-6690-06 DESCRIPTION

ASSY CABINET U/R ASSY SW PANEL PLAY INSTR SH JPT U/R ENG DENOMI SH ~ STICKER CERTIFICATE STICKER ELEC SPEC STICKER ELEC SPEC FOR TAIWAN STICKER SERIAL NUMBER STICKER INSTR SUNLIGHT ENG STICKER D MONITOR ENG POLY COVER 900 x 1300 x 1800 STICKER W POWER OFF ENG STICKER C ZMB U/R ENG COVER

TMP PRF SCR TH CRM M4 x8 S B TAPE 19MM 50M ROLL L=70 TMP PRF SCR TH BLK M4x8

CARTON BOX 30 POLYETHYLENE BAG 240x370 OWNERS MANUAL JPT U/R ENG KEY MASTER FOR 220-5575 KEY BAG (SGB-1035X) WRENCH M4 TMP SCR WRENCH MS TMP SCR FUSE 6.4% 30 5SO00MA 125V SW MICRO TYPE LAMP WG B TYPE 6V 3W AC CABLE CONNECT TYPE 15A AC CABLE CONNECT TYPE 15A AC CABLE CONNECT TYPE FOR BXP POLY BAG 780 Xx 1000 x 0. 05 BILLBOARD PLATE JPT U/R POP PNL JPT U/R GLASS CLEANER NAC S-100

CHAIN BRKT CHAIN 1080 TMP PRF SCR TH CRM M4 x 12 FLG NUT M4 TMP PRF SCR TH CRM M4 x8 SHIPPING BRACKET

CAUTION INSTR COP U/R STICKER 220V STICKER 240V STICKER 110V (0-2/2)
NOTE

OTHERS TAIWAN

} AC 110V AREA AC 220~240V AREA

AC 220V AREA AC 240V ARBA AC 110V AREA

Page 65

@ ASSY CABINET U/R (JPT-10001) (0-1/2)

| -} ACPA -

(BBY Qu _| Oo | a | Wy

Page 66

@ ASSY CABINET U/R (JPT-10001) (0-2/2)

ITEM NO.PART NO.DESCRIPTIONNOTE
1JPT-1500ASSY SUB-CABI U/R
2JPT-1540AC UNIT
3JPT-1550ASSY SENSOR
4COP-1570ASSY MONITOR 29
5JPT-2200ASSY CONT PNL U/R
6JPT-3500ASSY BILLBOARD
1JPT-4500ASSY PWR SPLY U/R
8JPT-4600ASSY MAIN BD U/R
9COP-1510FRONT GLASS
10AIN-1032RUBBER PACKING
1AIN-1033GLASS HOLDER UPPER
12JPT-1509GLASS HOLDER LOWER
13AIN-1085CUSHION
14AIN-1036WOODEN MASK
15AIN-1044MIRROR BRKT
16AIN-1038MIRROR
17AIN-1039MIRROR SASH
18AIN-1040MIRROR HOLDER
19253-5366CASH BOX
21421-8885STICKER CAUTION FORK
201000-F00416M SCR FH M4x 16
202000-P00412-WM SCR PH W/FS M4x 12
203000-T00420-0BM SCR TH BLK M4 x 20
204008-T00412-0CTMP PRF SCR TH CRM M4 x 12
205000-T00516-0BM SCR TH BLK Md x 16
206000-T00520-0BM SCR TH BLK M5 x20
207008-T00525-0BTMP PRF SCR TH BLK M5 x 25
208030-000612-SHEX BLT W/S M6 x 12
209032-000430WING BLT M4 x 30
210050-F00400°FLG NUT M4
211060-F00600FLT WSHR M6
212068-441616FLT WSHR 4. 4-16 1.6
213068-441616-0BFLT WSHR BLK 4, 4-16 1.6
214068-552016-0BFLT WSHR BLK 5. 5-20 1.6
Page 67

(©) ASSY SUB-CABI U/R (JPT-1500) (0-1/3)

DE 20% 293010) 109) G 4 ( OOO SECTION AA

iS _

@ alm €)

Ss 2) c

Page 68

(©) ASSY SUB-CABI U/R (JPT-1500) (0-2/3)

ITEM NO.

e Sowmrts®Tswne lt PART NO.

-1530 W-0360 0-0395-01 T-1501 T-1502 T-1503 -1504 -1505 -1506 T-1507 C-1006 -1008 -1503 OP-1506 DP-1148X DP-1167 UP-1018 105-5239-03 105-5169 105-5171 105-5258-01 117-0062 117-5098 117-5191 117-5247 253-5396-02 421-7501-02 838-11856-01 421-6595-05 JPT-1508 SCR-1008 i BaBa] eS

So COFE eee ee nuane

130-5155 220-5237- ~ 220-5574 220-5575 280-5275-SR10 310-5029-F20 601-9377 601-5699X 560-5316 514-5036-5000 280-5009-01 280-0419 601-0460

000-P00416-W 000-P00420-W 000-T00420-0B 000-T00420-0C 008-T00430-0B 011-T00312 ESCRIPTION NOTE

‘AN UNIT SW UNIT METER UNIT S WOODEN CABINET FRONT DOOR STICKER SIDE L JPT U/R STICKER SIDE R JPT U/R WOOFER BRKT WOOFER HOLD RUBBER (OOK BRKT LEG BRACKET MONITOR SUPPORT BRKT ACK DOOR RE COVER NG IG LKG R VENT R VENT OCK BRACKET W HUTE PLATE SINGLE IPPING HOOK BRKT RED LATE LOCK RETAINER NG RETAINER PLATE LATE PLATE 6-80 CABINET HANDLE WHITE STICKER 6. 3V 0, 15A CONNECT BD W/FUSE & COVER STICKER 5A ROTECT SHEET B NUT PLATE FOR CASTER cSeesc= a a

sue

SPEAKER BOX SUB WOOFER ASSY C.C 2DR ~ CAM LOCK W/KEYS CAM LOCK MASTER W/O KEY CORD CLAMP SR10 SUMI TUBE F F 20MM CASTER FAI=75 LEG ADJUSTER BOLT M16 x75 XFMR 100V5A 12. 5V6A FUSE 6.430 5000MA 125V CORD CLAMP 21 HARNESS LUG PLASTIC TIE BELT 100MM

M SCR PH W/FS M4 x 16 M SCR PH W/FS M4x 20 M SCR TH BLK M4 x20 M SCR TH CRM M4 x 20 TMP PRF SCR TH BLK M4 x 30 TAP SCR TH 3x 12

Page 69

@ ASSY SUB-CABI U/R (JPT-1500) (0-3/3)

ITEM NO.PART NO.DESCRIPTIONNOTE
207011-T00325TAP SCR TH 3X25
208011-T03512TAP SCR TH 3.5 12
209030-000630-SCHEX BLT W/S CRM M6 x 30
210030-000830-SBHEX BLT W/S BLK M8 x 30
211031-000530-0CCRG BLT CRM M5 x 30
212031-000630-0CCRG BLT CRM M6 x 30
213050-F00500FLG NUT M5
214050-F00600FLG NUT M6
215050-H01600HEX NUT M16
216060-F00600FLT WSHR M6
217060-F00800-0BFLT WSHR BLK M8
218068-441616-0BFLT WSHR BLK 4, 4-16 1.6
219011-F00310TAP SCR FH 3x10
220010-P00406-FS-TITE SCR PH W/F M4x6
221000-P00408-WM SCR PH W/FS M4x8
222030-000625-SHEX BLT W/S M6 x 25
301600~-6455-02WIRE HARN C.C DOOR SINGLE
302600-6709-52WIRE HARN EARTH 400MM
303600-6709-54WIRE HARN BARTH 150MM
304600-6925-004WIRE HARN XFMR ACLOOV OUT
305600-6925-005WIRE HARN XFMR AC12. 5V OUT
306600-6925-006WIRE HARN CONN BD 15P
307600-6925-026WIRE HARN EXT SPEAKER A
308600-6925-027WIRE HARN DC12V
309600-6925-028WIRE HARN EXT SOUND
310600-6925-029WIRE HARN EXT RGB & 1/0
311600-6925-030WIRE HARN EXT I/O & A/D
312600-6925-031WIRE HARN EXT SOUND VR
313600-6925-032WIRE HARN EXT WOOFER
314600-6925-033WIRE HARN EXT LED BD
315600-6925-045WIRE HARN EARTH MAIN
316600-6925-047WIRE HARN EARTH COIN METER
Page 70

@) FAN UNIT (JPT-1530)

ITEM NO.PART NO.DESCRIPTIONNOTE
1150-5238FAN BRKT
101260-0011-02AXIAL FLOW FAN ACLOOV 50-60HZ
102601-8543FAN GUARD
103280-5275-SR10CORD CLAMP SR10
201000-P00312-WM SCR PH W/FS M3 x 12
Page 71

@® sW UNIT (SDW-0360)

VOLUME SERVICE TEST DEMAGIETIZE olor

(02}(09) (ot

ITEM NO.PART NO.DESCRIPTIONNOTE
1KR-1060SW BRACKET
2421-6481STICKER SW
101509-5028SW PB IM
102220-5179VOL CONT B-5K OHM
103601-0042KNOB 22MM
104310-5029-D20SUMITUBE F D20MM
105601-0460PLASTIC TIE BELT 100MM
301600-6373-53WIRE HARN TEST&SERVICE LEFT
302600-6373-55WIRE HARN VOL. LEFT
Page 72

© METER UNIT S (610-0395-01)

ITEM NO.PART NO.DESCRIPTIONNOTE
1105-5233-01METER BRKT S
2421-6591-01STICKER COIN METER
101220-5412MAG CNTR W/CONN
Page 73

@ AC UNIT (JPT-1540)

ITEM NO. (101

PART NO.

JPT-1541 421-8202 421-7468-02

214-0202 270-5020 280-0417 509-5453-V-B 512-5046-5000 512-5046-3000 280-5009-01 601-0460 310-5029-F20

010-P00306-F

600-6925-001 600-6925-002 600-6925-003 600-6925-043 600-6925-044 DESCRIPTION

AC BRACKET STICKER EARTH MARK STICKER C.P W/PIC

AC INLET PANEL TYPE NOISE FILTER AC250V 6A TERMINAL BINDING POST BLACK SW ROCKER J8 V-B C.P 5000MA CE UL C.P 3000MA CE UL CORD CLAMP 21 PLASTIC TIE BELT 100MM SUMI TUBE F F 20MM

S-TITE SCR PH W/F M3x6

WIRE HARN C. P. WIRE HARN N. FILTER IN WIRE HARN N. FILTER OUT WIRE HARN BARTH AC INLET WIRE HARN EARTH AC UNIT

NOTE

AC 110V AREA AC 220~240V AREA

Page 74

ASSY SENSOR (JPT-1550)

ITEM NO.PART NO.DESCRIPTIONNOTE
1JPT-1551SENSOR BRKT A
2JPT-1552SENSOR BRKT B
3JPT-1082IR COVER
4JPT-1553SENSOR BRKT C
101838-13145LED BD GUN SENSE
102280-5009-01CORD CLAMP 21
103280-5275-SR10CORD CLAMP SR10
201000-P00408-WBM SCR PH W/FS BLK M4x8
202050-U00300U NUT M3
203060-F00300FLT WSHR M3
301600-6925-039WIRE HARN LED BD A
302600-6925-040WIRE HARN LED BD B
303600-6925-041WIRE HARN LED BD C
304600-6925-042WIRE HARN LED BD D
Page 75

©) ASSY MONITOR 29 (COP-1570)

y WOOO a , os a bs |

Ch

>

  • SECTION A-A
ITEM NO.PART NO,DESCRIPTIONNOTE
1AIN-1026MONITOR BRKT A
2AIN-1027MONITOR BRKT B
3280-5112BUSH FOR TV
4280-5113COLLAR FOR TV
5280-5114SPACER 6, 4-252
101200-5242-24-05ASSY CLR DSPL 29 TYPE 24K 100V

200-5243-24-01 ASSY CLR DSPL 29 TYPE 24K 100V . 200-5387-24-01 ASSY CLR DSPL 29 TYPE 24K AUTO 100V

201000-P00512-WM SCR PH W/FS M5 x12
202050-F00600FLG NUT M6
Page 76

ASSY CONT PNL U/R (JPT-2200) (0-1/2)

y 6 Oe

@) de Le OO OOO 1

Page 77

ASSY CONT PNL U/R (JPT-2200) (0-2/2)

ITEM NO.PART NO.DESCRIPTIONNOTE
1JPT-2201CONT PANEL BASE
2JPT-2202SPEAKER NET
3JPT-2203SPEAKER BRKT
4JPT-2204PROTECT SHEBT
5JPT-2010CONTROL UNIT 1P U/R
6JPT-2060CONTROL UNIT 2P U/R
8CPT-1019HOLDER
101130-5162GULL BOX SPEAKER 80HM 8W
102280-5009-01CORD CLMAP 21
103280-5275-SR10CORD CLAMP SR10
104601-0460PLASTIC TIE BELT 100MM
201000-P00612-WM SCR PH W/FS M6 x 12
202012-P00412TAP SCR #2 PH 4x12
203031-000410-0CCRG BLT CRM M4x 10
204050-F00400FLG NUT M4
205050-U00400U NUT M4
206060-F00400FLT WSHR M4
301600-6925-034WIRE HARN EXT SW PANEL
302600-6925-036WIRE HARN EXT SPEAKER B
303600-6925-046WIRE HARN EARTH CONT PNL

—7i-

Page 78

@ CONTROL UNIT 1P U/R (JPT-2010) (0-1/2)

and adjust the Actuator so as to allow the Trigger of © to turn

NOTE: When assembling (@), bend the Actuator as shown in the Detail FIG.

the Microswitch ON-OFF correctly.

Page 79

(©) CONTROL UNIT 1P U/R (JPT-2010) (D-2/2)

ITEM NO.

annwnre PART NO.

JPT-2030 COP-2005 125-5124 253-5404-01 253-5405-01 253-5406-01

280-5124-03 310-5029-D20 509-5080 601-0460

000-P00308-0B 012-P00308 FAS-000015 FAS-500006 060-F00300

600-6925-037 DESC IPTION NOTE

SENSOR UNIT STOP! TORS COVE! COVE! ER PIN ON SPRING LEFT BLUE RIGHT BLUE TRIGGER BLUE

NYLON CLAMP NKO3 SUMITUBE F D 20 MM SW M CRO TYPE PLASTIC TIE BELT 100MM

M SCR PH BLK M3 x8 TAP SCR #2 PH 3x8 M SCR PH BLK M3 25 CAP UT TYPE 3 BLK M3 FLT WSHR M3

WIRE HARN GUN 1P

Page 80

(@® SENSOR UNIT (JPT-2030)

ITEM NO.PART NO.DESCRIPTIONNOTE
1JPT-2031SENSOR HOLDER
101838-13144SENSOR BD GUN SENSE
201012-P00306TAP SCR #2 PH 3x6
Page 81

(©) CONTROL UNIT 2P U/R (JPT-2060) (0-1/2)

the Actuator as shown in the Detail FIG.

0 as to allow the Trigger of © to turn

:

E

: é E

Page 82

® CONTROL UNIT 2P U/R (JPT-2060) (D-2/2)

ITEM NO.

ounkwnre PART NO.

JPT-2030 COP-2005 125-5124 253-5404-02 253-5405-02 253-5406-02

280-5124-03 310-5029-D20 509-5080 601-0460

000-P00308-0B 012-P00308 FAS-000015 FAS-500006 060-F00309

600-6925-038 DESCRIPTION NOTE

SENSOR UNIT STOPPER PIN TORSION SPRING COVER LEFT RED COVER RIGHT RED TRIGGER RED

NYLON CLAMP NKO3 SUMITUBE F D 20 MM SW MICRO TYPE PLASTIC TIE BELT 100MM

M SCR PH BLK M3x8 TAP SCR #2 PH 3x8 M SCR PH BLK M3 x 25 CAP NUT TYPE 3 BLK M3 FLT WSHR M3

WIRE HARN GUN 2P

Page 83

ASSY SW PANEL (JPT-2300)

(‘01) ‘01

ITEM NO.PART NO.DESCRIPTIONNOTE
1JPT-2301INSTR PLATE JPT U/R
101509-5610-03YBSW PB 30M YELLOW W/L WH 5V 3W
301600-6457-10WIRE HARN START
302600-6457-36WIRE HARN START EX
Page 84

@ ASSY BILLBOARD (JPT-3500)

ITEM NO.

NMI RwWNMH PART NO.

JPT-3501 JPT-3502 JPT-3503 JPT-3504 JPT-3505 421-7501-17 440-WS0012XEG

390-5538-20SD 390-5636-20SD 390-5637-20SD 280-5275-SR10

000-F00408-0B 000-T00408-0B 000-P00430-W 000-T00412-0B 068-441616-0B

600-6925-035 DESCRIPTION

BILLBOARD CASE REFLECTOR LAMP COVER A LAMP COVER B BILLBOARD UPPER SUSH STICKER FL 20W STICKER W HIGH TEMP ENG

ASSY FL20W SD W/CONN HIGH L ASSY FL20W SD W/CONN HIGH S ASSY FL20W SD W/CONN HIGH T CORD CLAMP SR10

M SCR FH BLK M4x8 M SCR TH BLK M4x8 M SCR PH W/FS M4 x30 M SCR TH BLK M4 x 12 FLT WSHR BLK 4, 4-16 x 1.6

WIRE HARN FL

NOTE
Page 85

SINS OPK YQ a1oyy 7eY} ur “OV “suoTjiod yIe YSeTS oyy (2/1-@) (O0S¥-1Ldf) Y/N ATdS YMd ASSY cD)

Page 86

ASSY PWR SPLY U/R (JPT-4500) (0-2/2)

ITEM NO.PART NO.DESCRIPTIONNOTE
1JPT-4501PWR SPLY BASE U/R
2838-11650-29EQ. PWR AMP JPT C
3838-11651-91LOWPASS AMP
4838-13143-01IC BD GUN SENSE UR
5839-0979CONDENSER BD
101280-0419HARNESS LUG
102280-5009-01CORD CLAMP 21
103601-0460PLASTIC TIE BELT 100MM
201011-P00325TAP SCR PH 3x25
202011-T03512TAP SCR TH 3.5x 12
203011-F00310TAP SCR FH 3x10
301600-6925-007WIRE HARN BQ. AMP AC IN
302600-6925-008WIRE HARN EQ. AMP VR
303600-6925-009WIRE HARN EQ. AMP SOUND IN
304600-6925-010WIRE HARN EQ. AMP SPEAKER
305600-6925-011WIRE HARN AMP TO AMP
306600-6925-012WIRE HARN LAMP WOOFER
308600-6925-014WIRE HARN IC BD TO MAIN BD
309600-6925-015WIRE HARN IC BD TO LED BD
312600-6925-048WIRE HARN IC BD TO SENSOR
Page 87

(0-1/2) @ ASSY MAIN BD U/R (JPT-4600)

“SuOT}IOd YIeW YSETS OY} UT “Ojo “BUTITM OU ST diay} 1eY} aINs oyeH ey Og) Gi) (+) ©) O \LYLZZ2222277777LZALIT ILI LLL ELLA R ELE @ fal ral &(MAO|jouu”M Q@: OY|MA# VL TM MMU LEE “ @© ©@

Page 88

() ASSY MAIN BD U/R (JPT-4600) (D-2/2)

ITEM NO.PART NO.DESCRIPTIONNOTE
1JPT-0100ASSY SHIELD CASE
2JPT-4601MAIN BD BASE U/R
3105-5241SHIELD CASE BRKT
4839-0542AUDIO MIX BD
101400-5330-02SW REGU FOR MODEL3
102280-0419HARNESS LUG
103280-5009-01CORD CLAMP 21
201011-P00325TAP SCR PH 3X25
202011-T03512TAP SCR TH 3.5% 12
203011-F00310TAP SCR FH 3x10
204000-P00412-WM SCR PH W/FS M4x 12
205000-P00408-WM SCR PH W/FS M4x8
301600-6925-018WIRE HARN SW REGU AC IN
302600-6925-019WIRE HARN MAIN BD DC IN
303600-6925-020WIRE HARN SW REGU 18P
304600-6925-021WIRE HARN MAIN BD SOUND
305600-6925-022WIRE HARN AUDIO MIX BD OUT
306600-6925-023WIRE HARN MAIN BD RGB
307600-6925-024WIRE HARN MAIN BD 1/0
308600-6925-025WIRE HARN MAIN BD A/D
Page 89

ASSY SHIELD CASE (JPT-0100)

ITEM NO. PART NO.

105-5245 105-5242X 839-0951 833-13171 421-9174-01 421-6510-13171 601-8928

260-0064 280-5275-SR10 601-0460

000-P00320-W 000-P00408-W 010-P00308-F 010-P00310-F 010-P00365-F

600-6770-018-91 DESCRIPTION NOTE

SHI

GAME BD JPT LD CASE MODEL3 NVS SHIELD CASE LID MODEL3 FILTER BD MODEL3 JPT

STICKER CAUTION ANTISTATIC STICKER 833-13171 ‘ON BOX MODEL3 CAR’

FAN CORI MOTOR CLMAI PLASTIC T DC12V SR10 E BELT 100MM

M SCR PH W/FS M3 x 20 M SCR PH W/FS M4x8 S-T TE SC PH W/F M3 x8 S-TITE SCR PH W/F M3 x 10 TE SCR PH W/F M3 x65 S-T

WIRE HARN FAN MOTOR

Page 90
  • WIRE COLOR CODE TABLE

THE WIRE COLOR CODE is as follow:

MoUaAW> PINK SKY BLUE BROWN PURPLE LIGHT GREEN

Wires other than those of any of the above 5 single colors will be displayed by 2 alphanumeric characters.

COIWNAWNE RED BLUE YELLOW GREEN WHITE ORANGE BLACK GRAY

If the right-hand side numeral of the code is 0, then the wire will be of a single color shown by the left-hand side numeral (see the above).

Note 1:
Note 2: If the right-hand side alphanumeric is not 0, that particular wire has a spiral color code. The left-hand side character shows the base color and the right-hand side one, the spiral color.

<Example> 510 rrr WHITE / RED a — 1

RED WHITE

The character following the wire color code indicates the size of the wire.

K: AWG18, UL1015 L AWG20, UL1007 None: AWG22, UL1007

Page 91

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 92

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 93

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 94

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 95

SEGA ENTERPRISES, LTD. 12-14, Higashikohjiya 2-Chome, Ohta-ku, Tokyo, Japan 144-8532 OTEL : (03) 5737-7544 OFAX : (03) 5737-7746

© SEGA 1998

Printed in Japan